@inproceedings{LangohrBungCrookston2022, author = {Langohr, Philipp and Bung, Daniel Bernhard and Crookston, Brian M.}, title = {Hybrid investigation of labyrinth weirs: Discharge capacity and energy dissipation}, series = {Proceedings of the 39th IAHR World Congress}, booktitle = {Proceedings of the 39th IAHR World Congress}, editor = {Ortega-S{\´a}nchez, Miguel}, publisher = {International Association for Hydro-Environment Engineering and Research (IAHR)}, address = {Madrid}, isbn = {978-90-832612-1-8}, issn = {2521-7119 (print)}, doi = {10.3850/IAHR-39WC252171192022738}, pages = {2313 -- 2318}, year = {2022}, abstract = {The replacement of existing spillway crests or gates with labyrinth weirs is a proven techno-economical means to increase the discharge capacity when rehabilitating existing structures. However, additional information is needed regarding energy dissipation of such weirs, since due to the folded weir crest, a three-dimensional flow field is generated, yielding more complex overflow and energy dissipation processes. In this study, CFD simulations of labyrinth weirs were conducted 1) to analyze the discharge coefficients for different discharges to compare the Cd values to literature data and 2) to analyze and improve energy dissipation downstream of the structure. All tests were performed for a structure at laboratory scale with a height of approx. P = 30.5 cm, a ratio of the total crest length to the total width of 4.7, a sidewall angle of 10° and a quarter-round weir crest shape. Tested headwater ratios were 0.089 ≤ HT/P ≤ 0.817. For numerical simulations, FLOW-3D Hydro was employed, solving the RANS equations with use of finite-volume method and RNG k-ε turbulence closure. In terms of discharge capacity, results were compared to data from physical model tests performed at the Utah Water Research Laboratory (Utah State University), emphasizing higher discharge coefficients from CFD than from the physical model. For upstream heads, some discrepancy in the range of ± 1 cm between literature, CFD and physical model tests was identified with a discussion regarding differences included in the manuscript. For downstream energy dissipation, variable tailwater depths were considered to analyze the formation and sweep-out of a hydraulic jump. It was found that even for high discharges, relatively low downstream Froude numbers were obtained due to high energy dissipation involved by the three-dimensional flow between the sidewalls. The effects of some additional energy dissipation devices, e.g. baffle blocks or end sills, were also analyzed. End sills were found to be non-effective. However, baffle blocks with different locations may improve energy dissipation downstream of labyrinth weirs.}, language = {en} } @inproceedings{LandHoeherGligorevic2004, author = {Land, Ingmar and Hoeher, Peter Adam and Gligorevic, Snjezana}, title = {Computation of symbol-wise mutual information in transmission systems with logAPP decoders and application to EXIT charts}, series = {5th International ITG Conference on Source and Channel Coding (SCC) : January 14 - 16, 2004, Erlangen ; conference record. (ITG-Fachbericht ; 181)}, booktitle = {5th International ITG Conference on Source and Channel Coding (SCC) : January 14 - 16, 2004, Erlangen ; conference record. (ITG-Fachbericht ; 181)}, publisher = {VDE-Verl.}, address = {Berlin [u.a.]}, organization = {International Conference Source and Channel Coding <5, 2004, Erlangen>}, isbn = {3-8007-2802-8}, pages = {195 -- 202}, year = {2004}, language = {en} } @inproceedings{LahrsKrisamHerrmann2023, author = {Lahrs, Lennart and Krisam, Pierre and Herrmann, Ulf}, title = {Envisioning a collaborative energy system planning platform for the energy transition at the district level}, series = {ECOS 2023. The 36th International Conference on Efficiency, Cost, Optimization, Simulation and Environmental Impact of Energy Systems}, booktitle = {ECOS 2023. The 36th International Conference on Efficiency, Cost, Optimization, Simulation and Environmental Impact of Energy Systems}, publisher = {Procedings of ECOS 2023}, doi = {10.52202/069564-0284}, pages = {3163 -- 3170}, year = {2023}, abstract = {Residential and commercial buildings account for more than one-third of global energy-related greenhouse gas emissions. Integrated multi-energy systems at the district level are a promising way to reduce greenhouse gas emissions by exploiting economies of scale and synergies between energy sources. Planning district energy systems comes with many challenges in an ever-changing environment. Computational modelling established itself as the state-of-the-art method for district energy system planning. Unfortunately, it is still cumbersome to combine standalone models to generate insights that surpass their original purpose. Ideally, planning processes could be solved by using modular tools that easily incorporate the variety of competing and complementing computational models. Our contribution is a vision for a collaborative development and application platform for multi-energy system planning tools at the district level. We present challenges of district energy system planning identified in the literature and evaluate whether this platform can help to overcome these challenges. Further, we propose a toolkit that represents the core technical elements of the platform. Lastly, we discuss community management and its relevance for the success of projects with collaboration and knowledge sharing at their core.}, language = {en} } @inproceedings{KueppersSchubaNeugebaueretal.2023, author = {K{\"u}ppers, Malte and Schuba, Marko and Neugebauer, Georg and H{\"o}ner, Tim and Hack, Sacha}, title = {Security analysis of the KNX smart building protocol}, series = {ARES '23: Proceedings of the 18th International Conference on Availability, Reliability and Security}, booktitle = {ARES '23: Proceedings of the 18th International Conference on Availability, Reliability and Security}, publisher = {ACM}, doi = {10.1145/3600160.3605167}, pages = {1 -- 7}, year = {2023}, abstract = {KNX is a protocol for smart building automation, e.g., for automated heating, air conditioning, or lighting. This paper analyses and evaluates state-of-the-art KNX devices from manufacturers Merten, Gira and Siemens with respect to security. On the one hand, it is investigated if publicly known vulnerabilities like insecure storage of passwords in software, unencrypted communication, or denialof-service attacks, can be reproduced in new devices. On the other hand, the security is analyzed in general, leading to the discovery of a previously unknown and high risk vulnerability related to so-called BCU (authentication) keys.}, language = {en} } @inproceedings{KoetterDeckerDetzleretal.2012, author = {K{\"o}tter, Jens and Decker, Stefan and Detzler, Raphael and Sch{\"a}fer, Jochen and Schmitz, Mark and Herrmann, Ulf}, title = {Cost Reduction of Solar Fields with HelioTrough Collector}, publisher = {FLAGSOL}, address = {K{\"o}ln}, pages = {9 S. : Ill., graph. Darst.}, year = {2012}, language = {en} } @inproceedings{KoenigWolf2018, author = {K{\"o}nig, Johannes Alexander and Wolf, Martin R.}, title = {Cybersecurity awareness training provided by the competence developing game GHOST}, series = {ACHI 2018 : The Eleventh International Conference on Advances in Computer-Human Interactions}, booktitle = {ACHI 2018 : The Eleventh International Conference on Advances in Computer-Human Interactions}, isbn = {978-1-61208-616-3}, pages = {81 -- 87}, year = {2018}, abstract = {This paper introduces a Competence Developing Game (CDG) for the purpose of a cybersecurity awareness training for businesses. The target audience will be discussed in detail to understand their requirements. It will be explained why and how a mix of business simulation and serious game meets these stakeholder requirements. It will be shown that a tablet and touchscreen based approach is the most suitable solution. In addition, an empirical study will be briefly presented. The study was carried out to examine how an interaction system for a 3D-tablet based CDG has to be designed, to be manageable for non-game experienced employees. Furthermore, it will be explained which serious content is necessary for a Cybersecurity awareness training CDG and how this content is wrapped in the game}, language = {en} } @inproceedings{KoenigWolf2016, author = {K{\"o}nig, Johannes Alexander and Wolf, Martin R.}, title = {A new definition of competence developing games - and a framework to assess them}, series = {ACHI 2016 : The Ninth International Conference on Advances in Computer-Human Interactions}, booktitle = {ACHI 2016 : The Ninth International Conference on Advances in Computer-Human Interactions}, isbn = {978-1-61208-468-8}, pages = {95 -- 97}, year = {2016}, abstract = {There are different types of games that try to make use of the motivation of a gaming situation in learning contexts. This paper introduces the new terminology 'Competence Developing Game' (CDG) as an umbrella term for all games with this intention. Based on this new terminology, an assessment framework has been developed and validated in scope of an empirical study. Now, all different types of CDGs can be evaluated according to a defined and uniform set of assessment criteria and, thus, are comparable according to their characteristics and effectiveness.}, language = {en} } @inproceedings{KoenigWolf2016, author = {K{\"o}nig, Johannes Alexander and Wolf, Martin R.}, title = {The pyramid assessment framework for 'competence developing games'}, series = {Communications in Computer and Information Science}, volume = {618}, booktitle = {Communications in Computer and Information Science}, editor = {Stephanidis, C.}, publisher = {Springer}, isbn = {978-331940541-4}, issn = {1865-0929}, doi = {10.1007/978-3-319-40542-1_37}, pages = {232 -- 237}, year = {2016}, language = {en} } @inproceedings{KoenigVoelkerWolf2018, author = {K{\"o}nig, Johannes Alexander and V{\"o}lker, Veronika and Wolf, Martin R.}, title = {The user-focused storybuilding framework for competence developing games - a design-framework considering the basics of an educational game's story}, series = {ACHI 2018 : The Eleventh International Conference on Advances in Computer-Human Interactions}, booktitle = {ACHI 2018 : The Eleventh International Conference on Advances in Computer-Human Interactions}, isbn = {978-1-61208-616-3}, pages = {98 -- 106}, year = {2018}, abstract = {During the development of a Competence Developing Game's (CDG) story it is indispensable to understand the target audience. Thereby, CDGs stories represent more than just the plot. The Story is about the Setting, the Characters and the Plot. As a toolkit to support the development of such a story, this paper introduces the UserFocused Storybuilding (short UFoS) Framework for CDGs. The Framework and its utilization will be explained, followed by a description of its development and derivation, including an empirical study. In addition, to simplify the Framework use regarding the CDG's target audience, a new concept of Nine Psychographic Player Types will be explained. This concept of Player Types provides an approach to handle the differences in between players during the UFoS Framework use. Thereby, this article presents a unique approach to the development of target group-differentiated CDGs stories.}, language = {en} } @inproceedings{KoellenspergerBragardPlumetal.2007, author = {K{\"o}llensperger, P. and Bragard, Michael and Plum, T. and De Doncker, R. W.}, title = {The dual GCT : a new high-power device using optimized GCT technology}, series = {Conference record of the 2007 IEEE Industry Applications Conference : 42. IAS annual meeting ; September 23 - 27, 2007, New Orleans, Louisiana, USA}, booktitle = {Conference record of the 2007 IEEE Industry Applications Conference : 42. IAS annual meeting ; September 23 - 27, 2007, New Orleans, Louisiana, USA}, publisher = {IEEE Operations Center}, address = {Piscataway, NJ}, isbn = {978-1-4244-1260-0 (Online)}, doi = {10.1109/07IAS.2007.76}, pages = {358 -- 365}, year = {2007}, language = {en} } @inproceedings{Kurz2008, author = {Kurz, Melanie}, title = {On the benefit of moving images for the evaluation of form in virtual space : reflections in model theory}, series = {Design and semantics of form and movement : DeSForM 2008 ; [Hochschule f{\"u}r Gestaltung Offenbach am Main, 6.-7.11.2008]}, booktitle = {Design and semantics of form and movement : DeSForM 2008 ; [Hochschule f{\"u}r Gestaltung Offenbach am Main, 6.-7.11.2008]}, editor = {Feijs, Loe}, publisher = {Philips}, address = {Eindhoven}, isbn = {978-90-809801-2-9}, pages = {31 -- 34}, year = {2008}, language = {en} } @inproceedings{Kurz2006, author = {Kurz, Melanie}, title = {Recognition of shape in virtual visualizations}, series = {Proceedings : November 15 - 17, 2006, Technische Universit{\"a}t Darmstadt, Darmstadt, Germany ; PACE, Partners for the advancement of collaborative engineering education}, booktitle = {Proceedings : November 15 - 17, 2006, Technische Universit{\"a}t Darmstadt, Darmstadt, Germany ; PACE, Partners for the advancement of collaborative engineering education}, publisher = {Techn. Univ.}, address = {Darmstadt}, isbn = {978-3-00-020161-5}, pages = {203 -- 209}, year = {2006}, language = {en} } @inproceedings{Kurz2008, author = {Kurz, Melanie}, title = {Theses on the significance of the model in the form-finding process}, series = {"Focused" - Current Design Research Projects and Methods : Swiss Design Network Symposium 2008, 30 - 31 May 2008 Mount Gurten, Berne Switzerland}, booktitle = {"Focused" - Current Design Research Projects and Methods : Swiss Design Network Symposium 2008, 30 - 31 May 2008 Mount Gurten, Berne Switzerland}, publisher = {SwissDesignNetwork, SDN}, address = {Genf}, isbn = {978-3-9523138-0-0}, pages = {115 -- 127}, year = {2008}, language = {en} } @inproceedings{Kuperjans2000, author = {Kuperjans, Isabel}, title = {Decision-support-system for technical, economical and ecological design and evaluation of industrial energy systems}, series = {Industrial ecology and sustainability : conferences and workshops ; September 22 - 25, 1999, Troyes, France}, booktitle = {Industrial ecology and sustainability : conferences and workshops ; September 22 - 25, 1999, Troyes, France}, editor = {Bourg, Dominique and Erkman, Suren}, publisher = {Universit{\´e} de technologie de Troyes Gen{\`e}ve : Institute for communication and analysis of science and technology}, address = {[Troyes]}, pages = {1 CD-ROM}, year = {2000}, language = {en} } @inproceedings{KunfermannDrumm2005, author = {Kunfermann, Philipp and Drumm, Christian}, title = {Lifting XML schemas to ontologies - the concept finder algorithm}, series = {MEDIATE 2005 First International Workshop on Mediation in Semantic Web Services Proceedings of the First International Workshop on Mediation in Semantic Web Services (MEDIATE 2005)}, booktitle = {MEDIATE 2005 First International Workshop on Mediation in Semantic Web Services Proceedings of the First International Workshop on Mediation in Semantic Web Services (MEDIATE 2005)}, pages = {113 -- 122}, year = {2005}, language = {en} } @inproceedings{KumaranGopinathanRazalietal.2013, author = {Kumaran, P. and Gopinathan, M. and Razali, N. M. and Kuperjans, Isabel and Hariffin, B. and Hamdan, H.}, title = {Preliminary evaluation of atomization characteristics of improved biodiesel for gas turbine application}, series = {IOP Conference Series: Earth and Environmental Science (EES)}, volume = {16}, booktitle = {IOP Conference Series: Earth and Environmental Science (EES)}, number = {1}, publisher = {Institute of Physics Publishing (IOP)}, address = {London [u.a.]}, issn = {1755-1315}, doi = {10.1088/1755-1315/16/1/012014}, pages = {012014/1 -- 012014/4}, year = {2013}, language = {en} } @inproceedings{KuhnhenneDoeringPyschnyetal.2012, author = {Kuhnhenne, Markus and D{\"o}ring, Bernd and Pyschny, Dominik and Feldmann, Markus}, title = {Energy efficient sandwich construction}, series = {Proceedings of the VI International Congress on Architectural Envelopes : 20.6. - 22.6.2012, San Sebastian, Spain}, booktitle = {Proceedings of the VI International Congress on Architectural Envelopes : 20.6. - 22.6.2012, San Sebastian, Spain}, publisher = {ICAE}, organization = {International Congress on Architectural Envelopes <6, 2012, San Sebastian>}, pages = {277 -- 285}, year = {2012}, language = {en} } @inproceedings{KuhlmannButenwegLopezetal.2004, author = {Kuhlmann, Wolfram and Butenweg, Christoph and Lopez, Marijen and Fernandez, Sebastian}, title = {Seismic vulnerability assessment of the historic Aachen Cathedral}, series = {Conference proceedings / 13th World Conference on Earthquake Engineering [Vancouver, British Columbia, Canada, August 1 - 6, 2004] / [hosted by CAEE/ACGP, Canadian Association for Earthquake Engineering]}, booktitle = {Conference proceedings / 13th World Conference on Earthquake Engineering [Vancouver, British Columbia, Canada, August 1 - 6, 2004] / [hosted by CAEE/ACGP, Canadian Association for Earthquake Engineering]}, publisher = {CAEE}, address = {Vancouver}, organization = {World Conference on Earthquake Engineering <13, 2004, Vancouver>}, pages = {1 -- 14}, year = {2004}, language = {en} } @inproceedings{KuhlenDigel2017, author = {Kuhlen, Max and Digel, Ilya}, title = {Fluorescence signatures and detection limits of ubiquitous terrestrial bio-compounds}, series = {2nd YRA MedTech Symposium 2017 : June 8th - 9th / 2017 / Hochschule Ruhr-West}, booktitle = {2nd YRA MedTech Symposium 2017 : June 8th - 9th / 2017 / Hochschule Ruhr-West}, editor = {Erni, Daniel and Fischerauer, Alice and Himmel, J{\"o}rg and Seeger, Thomas and Thelen, Klaus}, publisher = {Universit{\"a}t Duisburg-Essen}, address = {Duisburg}, organization = {MedTech Symposium}, isbn = {978-3-9814801-9-1}, doi = {10.17185/duepublico/43984}, pages = {102 -- 103}, year = {2017}, language = {en} } @inproceedings{KubalskiMarinkovićButenweg2016, author = {Kubalski, T. and Marinković, Marko and Butenweg, Christoph}, title = {Numerical investigation of masonry infilled R.C. frames}, series = {Brick and Block Masonry. Proceedings of the 16th International Brick and Block Masonry Conference, Padova, Italy, 26-30 June 2016}, booktitle = {Brick and Block Masonry. Proceedings of the 16th International Brick and Block Masonry Conference, Padova, Italy, 26-30 June 2016}, editor = {Modena, Claudio}, publisher = {CRC Press}, address = {Leiden}, isbn = {9781315374963}, pages = {1219 -- 1226}, year = {2016}, language = {en} } @inproceedings{KubalskiButenwegMarinkovićetal.2017, author = {Kubalski, T. and Butenweg, Christoph and Marinković, Marko and Klinkel, S.}, title = {Investigation Of The Seismic Behaviour Of Infill Masonry Using Numerical Modelling Approaches}, series = {16th World Conference on Earthquake Engineering, 16WCEE 2017 Santiago Chile, January 9th to 13th 2017}, booktitle = {16th World Conference on Earthquake Engineering, 16WCEE 2017 Santiago Chile, January 9th to 13th 2017}, publisher = {Chilean Association on Seismology and Earthquake Engineering (ACHISINA)}, pages = {1 -- 11}, year = {2017}, abstract = {Masonry is a widely spread construction type which is used all over the world for different types of structures. Due to its simple and cheap construction, it is used as non-structural as well as structural element. In frame structures, such as reinforced concrete frames, masonry may be used as infill. While the bare frame itself is able to carry the loads when it comes to seismic events, the infilled frame is not able to warp freely due to the constrained movement. This restraint results in a complex interaction between the infill and the surrounding frame, which may lead to severe damage to the infill as well as the surrounding frame. The interaction is studied in different projects and effective approaches for the description of the behavior are still lacking. Experimental programs are usually quite expensive, while numerical models, once validated, do offer an efficient approach for the investigation of the interaction when horizontally loaded. In order to study the numerous parameters influencing the seismic load bearing behavior, numerical models may be used. Therefore, this contribution presents a numerical approach for the simulation of infill masonry in reinforced concrete frames. Both parts, the surrounding frame as well as the infill are represented by micro modelling approaches to correctly take into account the different types of failure. The adopted numerical model describes the inelastic behavior of the system, as indicated by the obtained results of the overall structural response as well as the formation of damage in the infilled wall. Comparison of the numerical and experimental results highlights the valuable contribution of numerical simulations in the study and design of infilled frames. As damage of the infill masonry may occur in-plane due to the interaction as well as out-of-plane due to the low vertical load, both directions of loading are investigated.}, language = {en} } @inproceedings{KruegerAnthrakidisFischeretal.2009, author = {Kr{\"u}ger, Dirk and Anthrakidis, Anette and Fischer, Stephan and Lokurlu, Ahmet and Walder, Markus and Croy, Reiner and Quaschning, Volker}, title = {Experiences with solar steam supply for an industrial steam network in the P3 Project}, series = {SolarPACES 2009 : electricity, fuels and clean water powered by the sun ; 15 - 18 September 2009, Berlin, Germany ; the 15th SolarPACES conference ; proceedings}, booktitle = {SolarPACES 2009 : electricity, fuels and clean water powered by the sun ; 15 - 18 September 2009, Berlin, Germany ; the 15th SolarPACES conference ; proceedings}, publisher = {Deutsches Zentrum f. Luft- u. Raumfahrt}, address = {Stuttgart}, isbn = {9783000287558}, pages = {1 CD-ROM}, year = {2009}, language = {en} } @inproceedings{KrueckelNoldenFerreinetal.2015, author = {Kr{\"u}ckel, Kai and Nolden, Florian and Ferrein, Alexander and Scholl, Ingrid}, title = {Intuitive visual teleoperation for UGVs using free-look augmented reality displays}, series = {2015 IEEE International Conference on Robotics and Automation (ICRA), Seattle, WA}, booktitle = {2015 IEEE International Conference on Robotics and Automation (ICRA), Seattle, WA}, doi = {10.1109/ICRA.2015.7139809}, pages = {4412 -- 4417}, year = {2015}, language = {en} } @inproceedings{KronigerHorikawaFunkeetal.2021, author = {Kroniger, Daniel and Horikawa, Atsushi and Funke, Harald and Pf{\"a}ffle, Franziska and Kishimoto, Tsuyoshi and Okada, Koichi}, title = {Experimental and numerical investigation on the effect of pressure on micromix hydrogen combustion}, series = {Conference Proceedings Turbo Expo: Power for Land, Sea and Air, Volume 3A: Combustion, Fuels, and Emissions}, booktitle = {Conference Proceedings Turbo Expo: Power for Land, Sea and Air, Volume 3A: Combustion, Fuels, and Emissions}, publisher = {ASME}, address = {New York, NY}, doi = {10.1115/GT2021-58926}, pages = {11 Seiten}, year = {2021}, abstract = {The micromix (MMX) combustion concept is a DLN gas turbine combustion technology designed for high hydrogen content fuels. Multiple non-premixed miniaturized flames based on jet in cross-flow (JICF) are inherently safe against flashback and ensure a stable operation in various operative conditions. The objective of this paper is to investigate the influence of pressure on the micromix flame with focus on the flame initiation point and the NOx emissions. A numerical model based on a steady RANS approach and the Complex Chemistry model with relevant reactions of the GRI 3.0 mechanism is used to predict the reactive flow and NOx emissions at various pressure conditions. Regarding the turbulence-chemical interaction, the Laminar Flame Concept (LFC) and the Eddy Dissipation Concept (EDC) are compared. The numerical results are validated against experimental results that have been acquired at a high pressure test facility for industrial can-type gas turbine combustors with regard to flame initiation and NOx emissions. The numerical approach is adequate to predict the flame initiation point and NOx emission trends. Interestingly, the flame shifts its initiation point during the pressure increase in upstream direction, whereby the flame attachment shifts from anchoring behind a downstream located bluff body towards anchoring directly at the hydrogen jet. The LFC predicts this change and the NOx emissions more accurately than the EDC. The resulting NOx correlation regarding the pressure is similar to a non-premixed type combustion configuration.}, language = {en} } @inproceedings{KronigerHorikawaFunkeetal.2021, author = {Kroniger, Daniel and Horikawa, Atsushi and Funke, Harald and Pf{\"a}ffle, Franziska}, title = {Numerical investigation of micromix hydrogen flames at different combustor pressure levels}, series = {The Proceedings of the International Conference on Power Engineering (ICOPE)}, booktitle = {The Proceedings of the International Conference on Power Engineering (ICOPE)}, doi = {10.1299/jsmeicope.2021.15.2021-0237}, pages = {4 Seiten}, year = {2021}, abstract = {This study investigates the influence of pressure on the temperature distribution of the micromix (MMX) hydrogen flame and the NOx emissions. A steady computational fluid dynamic (CFD) analysis is performed by simulating a reactive flow with a detailed chemical reaction model. The numerical analysis is validated based on experimental investigations. A quantitative correlation is parametrized based on the numerical results. We find, that the flame initiation point shifts with increasing pressure from anchoring behind a downstream located bluff body towards anchoring upstream at the hydrogen jet. The numerical NOx emissions trend regarding to a variation of pressure is in good agreement with the experimental results. The pressure has an impact on both, the residence time within the maximum temperature region and on the peak temperature itself. In conclusion, the numerical model proved to be adequate for future prototype design exploration studies targeting on improving the operating range.}, language = {en} } @inproceedings{KromeSander2018, author = {Krome, Cornelia and Sander, Volker}, title = {Time series analysis with apache spark and its applications to energy informatics}, series = {Proceedings of the 7th DACH+ Conference on Energy Informatics}, booktitle = {Proceedings of the 7th DACH+ Conference on Energy Informatics}, doi = {10.1186/s42162-018-0043-1}, year = {2018}, abstract = {In energy economy forecasts of different time series are rudimentary. In this study, a prediction for the German day-ahead spot market is created with Apache Spark and R. It is just an example for many different applications in virtual power plant environments. Other examples of use as intraday price processes, load processes of machines or electric vehicles, real time energy loads of photovoltaic systems and many more time series need to be analysed and predicted. This work gives a short introduction into the project where this study is settled. It describes the time series methods that are used in energy industry for forecasts shortly. As programming technique Apache Spark, which is a strong cluster computing technology, is utilised. Today, single time series can be predicted. The focus of this work is on developing a method to parallel forecasting, to process multiple time series simultaneously with R and Apache Spark.}, language = {en} } @inproceedings{KroggelBerndt1984, author = {Kroggel, Matthias and Berndt, Heinz}, title = {The 0-hydroxiphenyloxicarbonyl-group a new base labile amine protecting group}, series = {Peptides 1984 : Proceedings of the 18th European Peptide Symposium Djur{\"o}n{\"a}set, Sweden, June 10 - 15, 1984}, booktitle = {Peptides 1984 : Proceedings of the 18th European Peptide Symposium Djur{\"o}n{\"a}set, Sweden, June 10 - 15, 1984}, editor = {Ragnarsson, Ulf}, publisher = {Almquist \& Wiksell}, address = {Stockholm}, isbn = {91-22-00715-6}, pages = {81 -- 83}, year = {1984}, language = {en} } @inproceedings{KreyerMuellerEsch2020, author = {Kreyer, J{\"o}rg and M{\"u}ller, Marvin and Esch, Thomas}, title = {A Map-Based Model for the Determination of Fuel Consumption for Internal Combustion Engines as a Function of Flight Altitude}, publisher = {DGLR}, address = {Bonn}, doi = {10.25967/490162}, pages = {13 Seiten}, year = {2020}, abstract = {In addition to very high safety and reliability requirements, the design of internal combustion engines (ICE) in aviation focuses on economic efficiency. The objective must be to design the aircraft powertrain optimized for a specific flight mission with respect to fuel consumption and specific engine power. Against this background, expert tools provide valuable decision-making assistance for the customer. In this paper, a mathematical calculation model for the fuel consumption of aircraft ICE is presented. This model enables the derivation of fuel consumption maps for different engine configurations. Depending on the flight conditions and based on these maps, the current and the integrated fuel consumption for freely definable flight emissions is calculated. For that purpose, an interpolation method is used, that has been optimized for accuracy and calculation time. The mission boundary conditions flight altitude and power requirement of the ICE form the basis for this calculation. The mathematical fuel consumption model is embedded in a parent program. This parent program presents the simulated fuel consumption by means of an example flight mission for a representative airplane. The focus of the work is therefore on reproducing exact consumption data for flight operations. By use of the empirical approaches according to Gagg-Farrar [1] the power and fuel consumption as a function of the flight altitude are determined. To substantiate this approaches, a 1-D ICE model based on the multi-physical simulation tool GT-Suite® has been created. This 1-D engine model offers the possibility to analyze the filling and gas change processes, the internal combustion as well as heat and friction losses for an ICE under altitude environmental conditions. Performance measurements on a dynamometer at sea level for a naturally aspirated ICE with a displacement of 1211 ccm used in an aviation aircraft has been done to validate the 1-D ICE model. To check the plausibility of the empirical approaches with respect to the fuel consumption and performance adjustment for the flight altitude an analysis of the ICE efficiency chain of the 1-D engine model is done. In addition, a comparison of literature and manufacturer data with the simulation results is presented.}, language = {en} } @inproceedings{KreyerEsch2017, author = {Kreyer, J{\"o}rg and Esch, Thomas}, title = {Simulation Tool for Predictive Control Strategies for an ORCSystem in Heavy Duty Vehicles}, series = {European GT Conference 2017}, booktitle = {European GT Conference 2017}, pages = {16 Seiten}, year = {2017}, abstract = {Scientific questions - How can a non-stationary heat offering in the commercial vehicle be used to reduce fuel consumption? - Which potentials offer route and environmental information among with predicted speed and load trajectories to increase the efficiency of a ORC-System? Methods - Desktop bound holistic simulation model for a heavy duty truck incl. an ORC System - Prediction of massflows, temperatures and mixture quality (AFR) of exhaust gas}, language = {en} } @inproceedings{KremersPieper2015, author = {Kremers, Alexander and Pieper, Martin}, title = {Simulation and Verification of Bionic Heat Exchangers with COMSOL Multiphysics® Software}, series = {COMSOL Conference 2015 User Presentations ; COMSOL Conference 2015 Grenoble October 14 - 16, 2015 - World Trade Center, Grenoble, France}, booktitle = {COMSOL Conference 2015 User Presentations ; COMSOL Conference 2015 Grenoble October 14 - 16, 2015 - World Trade Center, Grenoble, France}, publisher = {COMSOL}, address = {G{\"o}ttingen ; Berlin}, pages = {6 Seiten}, year = {2015}, language = {en} } @inproceedings{KramerBragardRitzetal.2024, author = {Kramer, Pia and Bragard, Michael and Ritz, Thomas and Ferfer, Ute and Schiffers, Tim}, title = {Visualizing, Enhancing and Predicting Students' Success through ECTS Monitoring}, series = {2024 IEEE Global Engineering Education Conference (EDUCON)}, booktitle = {2024 IEEE Global Engineering Education Conference (EDUCON)}, publisher = {IEEE}, address = {New York, NY}, issn = {2165-9559}, doi = {10.1109/EDUCON60312.2024.10578652}, pages = {5 Seiten}, year = {2024}, abstract = {This paper serves as an introduction to the ECTS monitoring system and its potential applications in higher education. It also emphasizes the potential for ECTS monitoring to become a proactive system, supporting students by predicting academic success and identifying groups of potential dropouts for tailored support services. The use of the nearest neighbor analysis is suggested for improving data analysis and prediction accuracy.}, language = {en} } @inproceedings{KowalskiMcElwaine2008, author = {Kowalski, Julia and McElwaine, J.}, title = {Two-phase debris flow modeling}, series = {Geophysical Research Abstracts}, booktitle = {Geophysical Research Abstracts}, year = {2008}, language = {en} } @inproceedings{KowalskiMcArdellBartelt2006, author = {Kowalski, Julia and McArdell, B. W. and Bartelt, Perry}, title = {A comparison of two approaches to modeling multiphase gravity currents}, series = {Geophysical Research Abstracts}, volume = {8}, booktitle = {Geophysical Research Abstracts}, year = {2006}, language = {en} } @inproceedings{KowalskiBarteltMcElwaine2007, author = {Kowalski, Julia and Bartelt, Perry and McElwaine, J.}, title = {Two-phase debris flow modeling}, series = {Geophysical Research Abstracts}, booktitle = {Geophysical Research Abstracts}, year = {2007}, language = {en} } @inproceedings{Kowalski2006, author = {Kowalski, Julia}, title = {Numerical Debris Flow Simulation}, series = {Schweizer Numerik Kolloquium : Book of Abstracts 12. April 2006}, booktitle = {Schweizer Numerik Kolloquium : Book of Abstracts 12. April 2006}, pages = {1}, year = {2006}, language = {en} } @inproceedings{KorschDafnisReimerdesetal.2006, author = {Korsch, Helge and Dafnis, Athanasios and Reimerdes, Hans-G{\"u}nther and Braun, Carsten and Ballmann, Josef}, title = {Dynamic qualification of the HIRENASD elastic wing model}, series = {Motto: Luft- und Raumfahrt: Lehre, Forschung, Industrie - gemeinsam innovativ. Deutscher Luft- und Raumfahrtkongress 2006 : Braunschweig, 06. bis 09. November 2006. Jahrbuch / Deutsche Gesellschaft f{\"u}r Luft- und Raumfahrt. 2006}, booktitle = {Motto: Luft- und Raumfahrt: Lehre, Forschung, Industrie - gemeinsam innovativ. Deutscher Luft- und Raumfahrtkongress 2006 : Braunschweig, 06. bis 09. November 2006. Jahrbuch / Deutsche Gesellschaft f{\"u}r Luft- und Raumfahrt. 2006}, publisher = {Dt. Gesellschaft f{\"u}r Luft- und Raumfahrt - Lilienthal-Oberth (DGLR)}, address = {Bonn}, pages = {1441 -- 1450}, year = {2006}, language = {en} } @inproceedings{KonstantinidisKowalskiMartinezetal.2015, author = {Konstantinidis, K. and Kowalski, Julia and Martinez, C. F. and Dachwald, Bernd and Ewerhart, D. and F{\"o}rstner, R.}, title = {Some necessary technologies for in-situ astrobiology on enceladus}, series = {Proceedings of the International Astronautical Congress}, booktitle = {Proceedings of the International Astronautical Congress}, isbn = {978-151081893-4}, pages = {1354 -- 1372}, year = {2015}, language = {en} } @inproceedings{KonstantinidisDachwaldOhndorfetal.2013, author = {Konstantinidis, K. and Dachwald, Bernd and Ohndorf, A. and Dykta, P. and Voigt, K. and F{\"o}rstner, R.}, title = {Enceladus explorer (ENEX): A lander mission to probe subglacial water pockets on Saturn's moon enceladus for life}, series = {64th International Astronautical Congress 2013 (IAC 2013) : Beijing, China, 23 - 27 September 2013. (Proceedings of the International Astronautical Congress, IAC ; 2)}, booktitle = {64th International Astronautical Congress 2013 (IAC 2013) : Beijing, China, 23 - 27 September 2013. (Proceedings of the International Astronautical Congress, IAC ; 2)}, publisher = {Curran}, address = {Red Hook, NY}, organization = {International Astronautical Congress <64, 2013, Beijing>}, isbn = {978-1-62993-909-4}, pages = {1340 -- 1350}, year = {2013}, language = {en} } @inproceedings{KonradChudobaButenwegetal.2003, author = {Konrad, M. and Chudoba, Rostislav and Butenweg, Christoph and Bruckermann, O.}, title = {Textile reinforced concrete. Part II: Multi-level modeling concept}, series = {Digital proceedings / IKM 2003, proceedings 16th International Conference on the Applications of Computer Science and Mathematics in Architecture and Civil Engineering [Elektronische Ressource : 10. - 12. Juni 2003, Weimar] / Bauhaus-Universit{\"a}t Weimar. Ed.: K. G{\"u}rlebeck; L. Hempel; C. K{\"o}nke}, booktitle = {Digital proceedings / IKM 2003, proceedings 16th International Conference on the Applications of Computer Science and Mathematics in Architecture and Civil Engineering [Elektronische Ressource : 10. - 12. Juni 2003, Weimar] / Bauhaus-Universit{\"a}t Weimar. Ed.: K. G{\"u}rlebeck; L. Hempel; C. K{\"o}nke}, publisher = {IKM}, address = {Weimar}, organization = {Internationales Kolloquium {\"u}ber Anwendungen der Informatik und Mathematik in Architektur und Bauwesen <16, 2003, Weimar>}, pages = {1 -- 11}, year = {2003}, language = {en} } @inproceedings{KollSchwarzboezlHenneckeetal.2009, author = {Koll, Gerrit and Schwarzb{\"o}zl, Peter and Hennecke, Klaus and Hartz, Thomas and Schmitz, Mark and Hoffschmidt, Bernhard}, title = {The Solar Tower J{\"u}lich - a research and demonstration plant for central receiver systems}, series = {SolarPACES 2009 : electricity, fuels and clean water powered by the sun ; 15 - 18 September 2009, Berlin, Germany ; the 15th SolarPACES conference ; proceedings}, booktitle = {SolarPACES 2009 : electricity, fuels and clean water powered by the sun ; 15 - 18 September 2009, Berlin, Germany ; the 15th SolarPACES conference ; proceedings}, publisher = {Deutsches Zentrum f. Luft- u. Raumfahrt}, address = {Stuttgart}, isbn = {9783000287558}, pages = {1 CD-ROM}, year = {2009}, language = {en} } @inproceedings{KolkmannGriesSchleseretal.2005, author = {Kolkmann, Annette and Gries, Thomas and Schleser, Markus and Dilthey, Ulrich}, title = {Innovative yarn structures and coatings for textile reinforced concrete}, series = {All lectures / Techtextil Symposium : 6. - 9. 6.2005, Frankfurt am Main}, booktitle = {All lectures / Techtextil Symposium : 6. - 9. 6.2005, Frankfurt am Main}, address = {Frankfurt a.M.}, pages = {1 CD-ROM}, year = {2005}, language = {en} } @inproceedings{KolditzAlbrachtFasseetal.2015, author = {Kolditz, Melanie and Albracht, Kirsten and Fasse, Alessandro and Albin, Thivaharan and Br{\"u}ggemann, Gert-Peter and Abel, Dirk}, title = {Evaluation of an industrial robot as a leg press training device}, series = {XV International Symposium on Computer Simulation in Biomechanics July 9th - 11th 2015, Edinburgh, UK}, booktitle = {XV International Symposium on Computer Simulation in Biomechanics July 9th - 11th 2015, Edinburgh, UK}, pages = {41 -- 42}, year = {2015}, language = {en} } @inproceedings{KolditzAlbinFasseetal.2015, author = {Kolditz, Melanie and Albin, Thivaharan and Fasse, Alessandro and Br{\"u}ggemann, Gert-Peter and Abel, Dirk and Albracht, Kirsten}, title = {Simulative Analysis of Joint Loading During Leg Press Exercise for Control Applications}, series = {IFAC-PapersOnLine}, volume = {48}, booktitle = {IFAC-PapersOnLine}, number = {20}, doi = {10.1016/j.ifacol.2015.10.179}, pages = {435 -- 440}, year = {2015}, language = {en} } @inproceedings{KohlbergerWildKasperetal.2021, author = {Kohlberger, David-Sharif and Wild, Dominik and Kasper, Stefan and Czupalla, Markus}, title = {Modeling and analyses of a thermal passively stabilized LEO/GEO star tracker with embedded phase change material applying the Infused Thermal Solutions (ITS) method}, series = {ICES202: Satellite, Payload, and Instrument Thermal Control}, booktitle = {ICES202: Satellite, Payload, and Instrument Thermal Control}, publisher = {Texas Tech University}, address = {Lubbock, Tex.}, pages = {12 Seiten}, year = {2021}, abstract = {Phase change materials offer a way of storing excess heat and releasing it when it is needed. They can be utilized as a method to control thermal behavior without the need for additional energy. This work focuses on exploring the potential of using phase change materials to passively control the thermal behavior of a star tracker by infusing it with a fitting phase change material. Based on the numerical model of the star trackers thermal behavior using ESATAN-TMS without implemented phase change material, a fitting phase change material for selected orbits is chosen and implemented in the thermal model. The altered thermal behavior of the numerical model after the implementation is analyzed for different amounts of the chosen phase change materials using an ESATAN-based subroutine developed by the FH Aachen. The PCM-modelling-subroutine is explained in the paper ICES-2021-110. The results show that an increasing amount of phase change material increasingly damps temperature oscillations. Using an integral part structure some of the mass increase can be compensated.}, language = {en} } @inproceedings{KohlSchmidtsKloeseretal.2021, author = {Kohl, Philipp and Schmidts, Oliver and Kl{\"o}ser, Lars and Werth, Henri and Kraft, Bodo and Z{\"u}ndorf, Albert}, title = {STAMP 4 NLP - an agile framework for rapid quality-driven NLP applications development}, series = {Quality of Information and Communications Technology. QUATIC 2021}, booktitle = {Quality of Information and Communications Technology. QUATIC 2021}, publisher = {Springer}, address = {Cham}, isbn = {978-3-030-85346-4}, doi = {10.1007/978-3-030-85347-1_12}, pages = {156 -- 166}, year = {2021}, abstract = {The progress in natural language processing (NLP) research over the last years, offers novel business opportunities for companies, as automated user interaction or improved data analysis. Building sophisticated NLP applications requires dealing with modern machine learning (ML) technologies, which impedes enterprises from establishing successful NLP projects. Our experience in applied NLP research projects shows that the continuous integration of research prototypes in production-like environments with quality assurance builds trust in the software and shows convenience and usefulness regarding the business goal. We introduce STAMP 4 NLP as an iterative and incremental process model for developing NLP applications. With STAMP 4 NLP, we merge software engineering principles with best practices from data science. Instantiating our process model allows efficiently creating prototypes by utilizing templates, conventions, and implementations, enabling developers and data scientists to focus on the business goals. Due to our iterative-incremental approach, businesses can deploy an enhanced version of the prototype to their software environment after every iteration, maximizing potential business value and trust early and avoiding the cost of successful yet never deployed experiments.}, language = {en} } @inproceedings{KohlFreyerKraemeretal.2023, author = {Kohl, Philipp and Freyer, Nils and Kr{\"a}mer, Yoka and Werth, Henri and Wolf, Steffen and Kraft, Bodo and Meinecke, Matthias and Z{\"u}ndorf, Albert}, title = {ALE: a simulation-based active learning evaluation framework for the parameter-driven comparison of query strategies for NLP}, series = {Deep Learning Theory and Applications}, booktitle = {Deep Learning Theory and Applications}, editor = {Conte, Donatello and Fred, Ana and Gusikhin, Oleg and Sansone, Carlo}, publisher = {Springer}, address = {Cham}, isbn = {978-3-031-39058-6 (Print)}, doi = {10.1007/978-3-031-39059-3_16}, pages = {235 -- 253}, year = {2023}, abstract = {Supervised machine learning and deep learning require a large amount of labeled data, which data scientists obtain in a manual, and time-consuming annotation process. To mitigate this challenge, Active Learning (AL) proposes promising data points to annotators they annotate next instead of a subsequent or random sample. This method is supposed to save annotation effort while maintaining model performance. However, practitioners face many AL strategies for different tasks and need an empirical basis to choose between them. Surveys categorize AL strategies into taxonomies without performance indications. Presentations of novel AL strategies compare the performance to a small subset of strategies. Our contribution addresses the empirical basis by introducing a reproducible active learning evaluation (ALE) framework for the comparative evaluation of AL strategies in NLP. The framework allows the implementation of AL strategies with low effort and a fair data-driven comparison through defining and tracking experiment parameters (e.g., initial dataset size, number of data points per query step, and the budget). ALE helps practitioners to make more informed decisions, and researchers can focus on developing new, effective AL strategies and deriving best practices for specific use cases. With best practices, practitioners can lower their annotation costs. We present a case study to illustrate how to use the framework.}, language = {en} } @inproceedings{KobGoemmelButenwegetal.2006, author = {Kob, Malte and G{\"o}mmel, Andreas and Butenweg, Christoph and Niendorf, Thoralf}, title = {Training of a combined model of larynx and vocal folds with data from MRI measurements}, series = {The 5th International Conference on Voice Physiology and Biomechanics: Variations across Cultures and Species, July 12-14, 2006, Tokyo, Japan. Proceedings}, booktitle = {The 5th International Conference on Voice Physiology and Biomechanics: Variations across Cultures and Species, July 12-14, 2006, Tokyo, Japan. Proceedings}, organization = {International Conference on Voice Physiology and Biomechanics <5, 2006, Tokyo>}, pages = {45 -- 46}, year = {2006}, language = {en} } @inproceedings{KobButenweg2004, author = {Kob, Malte and Butenweg, Christoph}, title = {A finite element model of the interaction between intra-and extralaryngeal muscles}, series = {International Conference on Voice Physiology and Biomechanics, August 18-20, 2004, Marseille, France}, booktitle = {International Conference on Voice Physiology and Biomechanics, August 18-20, 2004, Marseille, France}, organization = {International Conference on Voice Physiology and Biomechanics <2004, Marseille>}, pages = {1 -- 2}, year = {2004}, language = {en} } @inproceedings{KnackstedtEggertHeddieretal.2013, author = {Knackstedt, Ralf and Eggert, Mathias and Heddier, Marcel and Chasin, Friedrich and Becker, J{\"o}rg}, title = {The Relationship of IS and Law - Insights into the German Online Car Registration Case}, series = {ECIS 2013 Completed Research. 18. Proceedings of the 21st European Conference on Information Systems}, booktitle = {ECIS 2013 Completed Research. 18. Proceedings of the 21st European Conference on Information Systems}, pages = {13 S.}, year = {2013}, language = {en} } @inproceedings{KnackstedtEggertHeddieretal.2013, author = {Knackstedt, Ralf and Eggert, Mathias and Heddier, Marcel and Chasin, Friedrich and Becker, J{\"o}rg}, title = {The Relationship Of Is And Law - The Perspective Of And Implications For IS Research}, series = {ECIS 2013 Completed Research. 18}, booktitle = {ECIS 2013 Completed Research. 18}, pages = {13 S.}, year = {2013}, language = {en} }