@inproceedings{WuKemper2016,
  author    = {Wu, Ziyi and Kemper, Hans},
  title     = {The optimal 48 V - battery pack for a specific load profile of a heavy duty vehicle},
  series = {8. Internationale Fachtagung Kraftwerk Batterie : 26. - 27. April 2016, M{\"u}nster, Deutschland},
  booktitle = {8. Internationale Fachtagung Kraftwerk Batterie : 26. - 27. April 2016, M{\"u}nster, Deutschland},
  year      = {2016},
  language  = {en}
}
@inproceedings{WellmerChenBraunetal.2007,
  author    = {Wellmer, Georg and Chen, B.-H. and Braun, Carsten and Ballmann, Josef},
  title     = {Numerical prediction of aeroelastic effects on twin-sting-rig mounted models for rear fuselage and empennage flow investigation in transonic windtunnel},
  series = {Proceedings / IFASD 2007, CEAS/AIAA/KTH International Forum on Aeroelasticity and Structural Dynamics, June 18 - 21, 2007, Stockholm, Sweden},
  booktitle = {Proceedings / IFASD 2007, CEAS/AIAA/KTH International Forum on Aeroelasticity and Structural Dynamics, June 18 - 21, 2007, Stockholm, Sweden},
  publisher = {KTH},
  address   = {Stockholm},
  organization    = {Confederation of European Aerospace Societies ; American Institute of Aeronautics and Astronautics, Reston, Va. ; Kungliga Tekniska H{\"o}gskolan, Stockholm},
  pages     = {1 CD-ROM},
  year      = {2007},
  language  = {en}
}
@inproceedings{WeissAbanteribaEsch2007,
  author    = {Weiss, Alexander and Abanteriba, Sylvester and Esch, Thomas},
  title     = {Investigation of Flow Separation Inside a Conical Rocket Nozzle With the Aid of an Annular Cross Flow},
  series = {Proceedings of the ASME/JSME 2007 5th Joint Fluids Engineering Conference. Volume 1: Symposia, Parts A and B},
  booktitle = {Proceedings of the ASME/JSME 2007 5th Joint Fluids Engineering Conference. Volume 1: Symposia, Parts A and B},
  publisher = {American Society of Mechanical Engineers (ASME)},
  address   = {New York},
  isbn      = {0-7918-4288-6},
  doi       = {10.1115/FEDSM2007-37387},
  pages     = {1861 -- 1871},
  year      = {2007},
  abstract  = {Flow separation is a phenomenon that occurs in all kinds of supersonic nozzles sometimes during run-up and shut-down operations. Especially in expansion nozzles of rocket engines with large area ratio, flow separation can trigger strong side loads that can damage the structure of the nozzle. The investigation presented in this paper seeks to establish measures that may be applied to alter the point of flow separation. In order to achieve this, a supersonic nozzle was placed at the exit plane of the conical nozzle. This resulted in the generation of cross flow surrounding the core jet flow from the conical nozzle. Due to the entrainment of the gas stream from the conical nozzle the pressure in its exit plane was found to be lower than that of the ambient. A Cold gas instead of hot combustion gases was used as the working fluid. A mathematical simulation of the concept was validated by experiment. Measurements confirmed the simulation results that due to the introduction of a second nozzle the pressure in the separated region of the conical nozzle was significantly reduced. It was also established that the boundary layer separation inside the conical nozzle was delayed thus allowing an increased degree of overexpansion. The condition established by the pressure measurements was also demonstrated qualitatively using transparent nozzle configurations.},
  language  = {en}
}
@inproceedings{WeberTellisDuhovic2016,
  author    = {Weber, Tobias and Tellis, Jane J. and Duhovic, Miro},
  title     = {Characterization of tool-part-interaction an interlaminar friction for manufacturing process simulation},
  series = {ECCM 17, 17th European Conference on Composite Materials, M{\"u}nchen, DE, Jun 26-30, 2016},
  booktitle = {ECCM 17, 17th European Conference on Composite Materials, M{\"u}nchen, DE, Jun 26-30, 2016},
  isbn      = {978-3-00-053387-7},
  pages     = {1 -- 7},
  year      = {2016},
  language  = {en}
}
@inproceedings{WeberEnglhardHaileretal.2019,
  author    = {Weber, Tobias and Englhard, Markus and Hailer, Benjamin and Arent, Jan-Christoph},
  title     = {Manufacturing Process Simulation for the Prediction of Tool-Part-Interaction and Ply Wrinkling},
  series = {Proceedings of SAMPE Europe Conference 2019, Nantes, France},
  booktitle = {Proceedings of SAMPE Europe Conference 2019, Nantes, France},
  pages     = {1 -- 10},
  year      = {2019},
  language  = {en}
}
@inproceedings{WeberEnglhardHaileretal.2015,
  author    = {Weber, Tobias and Englhard, Markus and Hailer, Benjamin and Arent, Jan-Christoph},
  title     = {Manufacturing Process Simulation for the Prediction of Tool-Part-Interaction and Ply Wrinkling},
  series = {Proceedings of SAMPE Europe Conference, Amiens , France},
  booktitle = {Proceedings of SAMPE Europe Conference, Amiens , France},
  pages     = {1 -- 10},
  year      = {2015},
  language  = {en}
}
@inproceedings{Weber2015,
  author    = {Weber, Tobias},
  title     = {Manufacturing Process Simulation for Tooling Optimization: Reduction of Quality Issues During Autoclave Manufacturing of Composite Parts},
  series = {Proceedings of SAMPE Europe Conference 2015, Amiens, France},
  booktitle = {Proceedings of SAMPE Europe Conference 2015, Amiens, France},
  pages     = {1 -- 8},
  year      = {2015},
  language  = {en}
}
@inproceedings{WaldmannVeraDachwaldetal.2018,
  author    = {Waldmann, Christoph and Vera, Jean-Pierre de and Dachwald, Bernd and Strasdeit, Henry and Sohl, Frank and Hanff, Hendrik and Kowalski, Julia and Heinen, Dirk and Macht, Sabine and Bestmann, Ulf and Meckel, Sebastian and Hildebrandt, Marc and Funke, Oliver and Gehrt, Jan-J{\"o}ran},
  title     = {Search for life in ice-covered oceans and lakes beyond Earth},
  series = {2018 IEEE/OES Autonomous Underwater Vehicle Workshop, Proceedings November 2018, Article number 8729761},
  booktitle = {2018 IEEE/OES Autonomous Underwater Vehicle Workshop, Proceedings November 2018, Article number 8729761},
  doi       = {10.1109/AUV.2018.8729761},
  year      = {2018},
  abstract  = {The quest for life on other planets is closely connected with the search for water in liquid state. Recent discoveries of deep oceans on icy moons like Europa and Enceladus have spurred an intensive discussion about how these waters can be accessed. The challenge of this endeavor lies in the unforeseeable requirements on instrumental characteristics both with respect to the scientific and technical methods. The TRIPLE/nanoAUV initiative is aiming at developing a mission concept for exploring exo-oceans and demonstrating the achievements in an earth-analogue context, exploring the ocean under the ice shield of Antarctica and lakes like Dome-C on the Antarctic continent.},
  language  = {en}
}
@inproceedings{Wahle1987,
  author    = {Wahle, Michael},
  title     = {Optimale Auslegung von Schwingungsd{\"a}mpfern zur Schwingungsberuhigung elastischer Strukturen},
  series = {D{\"a}mpfung von Schwingungen bei Maschinen und Bauwerken : Tagung N{\"u}rnberg, 9. u. 10. April 1987. - (VDI-Berichte ; 627)},
  booktitle = {D{\"a}mpfung von Schwingungen bei Maschinen und Bauwerken : Tagung N{\"u}rnberg, 9. u. 10. April 1987. - (VDI-Berichte ; 627)},
  publisher = {VDI-Verl.},
  address   = {D{\"u}sseldorf},
  isbn      = {3-18-090627-8},
  pages     = {355 -- 373},
  year      = {1987},
  language  = {de}
}
@inproceedings{Wahle1983,
  author    = {Wahle, Michael},
  title     = {Calculation of the response of heat exchanger tubes with regard to nonlinear and prestressing effects},
  series = {Vibration in nuclear plant : proceedings of the 3rd International Conference on Vibration in Nuclear Plant held on 11 - 14 May 1982, Keswick ; vol. 1},
  booktitle = {Vibration in nuclear plant : proceedings of the 3rd International Conference on Vibration in Nuclear Plant held on 11 - 14 May 1982, Keswick ; vol. 1},
  publisher = {British Nuclear Energy Society},
  address   = {London},
  isbn      = {0-7277-0192-4 (Druckausg.)},
  pages     = {162 -- 183},
  year      = {1983},
  language  = {en}
}
@inproceedings{Wahle1983,
  author    = {Wahle, Michael},
  title     = {Determination of flow induced nonlinear vibrations of prestressed heat exchanger tubes},
  series = {Advanced Course in Heat Exchangers : Theory and Practice ; ICHMT Symposium ; Dubrovnik, Croatia 1981. - (ICHMT digital library online ; 19)},
  booktitle = {Advanced Course in Heat Exchangers : Theory and Practice ; ICHMT Symposium ; Dubrovnik, Croatia 1981. - (ICHMT digital library online ; 19)},
  publisher = {Begell House},
  address   = {Redding, Connecticut},
  pages     = {339 -- 353},
  year      = {1983},
  language  = {en}
}
@inproceedings{VeettilRakshitSchopenetal.2022,
  author    = {Veettil, Yadu Krishna Morassery and Rakshit, Shantam and Schopen, Oliver and Kemper, Hans and Esch, Thomas and Shabani, Bahman},
  title     = {Automated Control System Strategies to Ensure Safety of PEM Fuel Cells Using Kalman Filters},
  series = {Proceedings of the 7th International Conference and Exhibition on Sustainable Energy and Advanced Materials (ICE-SEAM 2021), Melaka, Malaysia},
  booktitle = {Proceedings of the 7th International Conference and Exhibition on Sustainable Energy and Advanced Materials (ICE-SEAM 2021), Melaka, Malaysia},
  editor    = {Bin Abdollah, Mohd Fadzli and Amiruddin, Hilmi and Singh, Amrik Singh Phuman and Munir, Fudhail Abdul and Ibrahim, Asriana},
  publisher = {Springer Nature},
  address   = {Singapore},
  isbn      = {978-981-19-3178-9},
  issn      = {2195-4356},
  doi       = {10.1007/978-981-19-3179-6_55},
  pages     = {296 -- 299},
  year      = {2022},
  abstract  = {Having well-defined control strategies for fuel cells, that can efficiently detect errors and take corrective action is critically important for safety in all applications, and especially so in aviation. The algorithms not only ensure operator safety by monitoring the fuel cell and connected components, but also contribute to extending the health of the fuel cell, its durability and safe operation over its lifetime. While sensors are used to provide peripheral data surrounding the fuel cell, the internal states of the fuel cell cannot be directly measured. To overcome this restriction, Kalman Filter has been implemented as an internal state observer. Other safety conditions are evaluated using real-time data from every connected sensor and corrective actions automatically take place to ensure safety. The algorithms discussed in this paper have been validated thorough Model-in-the-Loop (MiL) tests as well as practical validation at a dedicated test bench.},
  language  = {en}
}
@inproceedings{ThomaStiemerBraunetal.2023,
  author    = {Thoma, Andreas and Stiemer, Luc and Braun, Carsten and Fisher, Alex and Gardi, Alessandro G.},
  title     = {Potential of hybrid neural network local path planner for small UAV in urban environments},
  series = {AIAA SCITECH 2023 Forum},
  booktitle = {AIAA SCITECH 2023 Forum},
  publisher = {AIAA},
  doi       = {10.2514/6.2023-2359},
  pages     = {13 Seiten},
  year      = {2023},
  abstract  = {This work proposes a hybrid algorithm combining an Artificial Neural Network (ANN) with a conventional local path planner to navigate UAVs efficiently in various unknown urban environments. The proposed method of a Hybrid Artificial Neural Network Avoidance System is called HANNAS. The ANN analyses a video stream and classifies the current environment. This information about the current Environment is used to set several control parameters of a conventional local path planner, the 3DVFH*. The local path planner then plans the path toward a specific goal point based on distance data from a depth camera. We trained and tested a state-of-the-art image segmentation algorithm, PP-LiteSeg. The proposed HANNAS method reaches a failure probability of 17\%, which is less than half the failure probability of the baseline and around half the failure probability of an improved, bio-inspired version of the 3DVFH*. The proposed HANNAS method does not show any disadvantages regarding flight time or flight distance.},
  language  = {en}
}
@inproceedings{ThomaFisherBraun2020,
  author    = {Thoma, Andreas and Fisher, Alex and Braun, Carsten},
  title     = {Improving the px4 avoid algorithm by bio-inspired flight strategies},
  series = {DLRK2020 - „Luft- und Raumfahrt - Verantwortung in allen Dimensionen"},
  booktitle = {DLRK2020 - „Luft- und Raumfahrt - Verantwortung in allen Dimensionen"},
  pages     = {10 Seiten},
  year      = {2020},
  language  = {en}
}
@inproceedings{ThomaFisherBertrandetal.2020,
  author    = {Thoma, Andreas and Fisher, Alex and Bertrand, Olivier and Braun, Carsten},
  title     = {Evaluation of possible flight strategies for close object evasion from bumblebee experiments},
  series = {Living Machines 2020: Biomimetic and Biohybrid Systems},
  booktitle = {Living Machines 2020: Biomimetic and Biohybrid Systems},
  editor    = {Vouloutsi, Vasiliki and Mura, Anna and Tauber, Falk and Speck, Thomas and Prescott, Tony J. and Verschure, Paul F. M. J.},
  publisher = {Springer},
  address   = {Cham},
  isbn      = {978-3-030-64312-6},
  doi       = {10.1007/978-3-030-64313-3_34},
  pages     = {354 -- 365},
  year      = {2020},
  language  = {en}
}
@inproceedings{ThenentDahmann2011,
  author    = {Thenent, N. E. and Dahmann, Peter},
  title     = {Increasing aircraft design flexibility - The development of a hydrostatic transmission for gliders with self-launching capability},
  series = {Deutscher Luft- und Raumfahrtkongress 2011 : Bremen, 27. bis 29. September 2011 ; Tagungsband},
  booktitle = {Deutscher Luft- und Raumfahrtkongress 2011 : Bremen, 27. bis 29. September 2011 ; Tagungsband},
  publisher = {Dt. Gesellschaft f{\"u}r Luft- und Raumfahrt},
  address   = {Bonn},
  isbn      = {978-3-9321-8274-7},
  pages     = {865 -- 883},
  year      = {2011},
  language  = {en}
}
@inproceedings{ThenentDahmann2011,
  author    = {Thenent, N. E. and Dahmann, Peter},
  title     = {Hydrostatic propeller drive},
  series = {Proceedings of the conference : 18 - 20 May, 2011 Tampere, Finland / the Twelth Scandinavian International Conference on Fluid Power, SICFP'11. Ed.: Harri Sairiala ... Vol. 1},
  booktitle = {Proceedings of the conference : 18 - 20 May, 2011 Tampere, Finland / the Twelth Scandinavian International Conference on Fluid Power, SICFP'11. Ed.: Harri Sairiala ... Vol. 1},
  address   = {Tampere},
  isbn      = {978-952-15-2517-9},
  pages     = {217 -- 227},
  year      = {2011},
  language  = {en}
}
@inproceedings{TheisKrisnamurthySchmitz2015,
  author    = {Theis, Jochen and Krisnamurthy, Hemanth Kumar and Schmitz, G{\"u}nter},
  title     = {Modellbasierte Simulation und experimentelle Anwendung von mechatronischen Systemen in der Lehre in Verbindung mit NI myRIO und dem NI LabVIEW Interface Toolkit},
  series = {Virtuelle Instrumente in der Praxis 2015 : Mess-, Steuer-, Regel- und Embedded-Systeme; Begleitband zum 20. VIP-Kongress},
  booktitle = {Virtuelle Instrumente in der Praxis 2015 : Mess-, Steuer-, Regel- und Embedded-Systeme; Begleitband zum 20. VIP-Kongress},
  editor    = {Jamal, Rahman},
  publisher = {VDE-Verl.},
  address   = {Berlin},
  isbn      = {978-3-8007-3669-0},
  pages     = {362 -- 365},
  year      = {2015},
  language  = {de}
}
@inproceedings{TamaldinMansorMatYaminetal.2022,
  author    = {Tamaldin, Noreffendy and Mansor, Muhd Rizuan and Mat Yamin, Ahmad Kamal and Bin Abdollah, Mohd Fazli and Esch, Thomas and Tonoli, Andrea and Reisinger, Karl Heinz and Sprenger, Hanna and Razuli, Hisham},
  title     = {Development of UTeM United Future Fuel Design Training Center Under Erasmus+ United Program},
  series = {Proceedings of the 7th International Conference and Exhibition on Sustainable Energy and Advanced Materials (ICE-SEAM 2021), Melaka, Malaysia},
  booktitle = {Proceedings of the 7th International Conference and Exhibition on Sustainable Energy and Advanced Materials (ICE-SEAM 2021), Melaka, Malaysia},
  editor    = {Bin Abdollah, Mohd Fadzli and Amiruddin, Hilmi and Singh, Amrik Singh Phuman and Munir, Fudhail Abdul and Ibrahim, Asriana},
  publisher = {Springer Nature},
  address   = {Singapore},
  isbn      = {978-981-19-3178-9},
  issn      = {2195-4356},
  doi       = {10.1007/978-981-19-3179-6_50},
  pages     = {274 -- 278},
  year      = {2022},
  abstract  = {The industrial revolution IR4.0 era have driven many states of the art technologies to be introduced especially in the automotive industry. The rapid development of automotive industries in Europe have created wide industry gap between European Union (EU) and developing countries such as in South-East Asia (SEA). Indulging this situation, FH Joanneum, Austria together with European partners from FH Aachen, Germany and Politecnico Di Torino, Italy is taking initiative to close the gap utilizing the Erasmus+ United grant from EU. A consortium was founded to engage with automotive technology transfer using the European ramework to Malaysian, Indonesian and Thailand Higher Education Institutions (HEI) as well as automotive industries. This could be achieved by establishing Engineering Knowledge Transfer Unit (EKTU) in respective SEA institutions guided by the industry partners in their respective countries. This EKTU could offer updated, innovative, and high-quality training courses to increase graduate's employability in higher education institutions and strengthen relations between HEI and the wider economic and social environment by addressing Universityindustry cooperation which is the regional priority for Asia. It is expected that, the Capacity Building Initiative would improve the quality of higher education and enhancing its relevance for the labor market and society in the SEA partners. The outcome of this project would greatly benefit the partners in strong and complementary partnership targeting the automotive industry and enhanced larger scale international cooperation between the European and SEA partners. It would also prepare the SEA HEI in sustainable partnership with Automotive industry in the region as a mean of income generation in the future.},
  language  = {en}
}
@inproceedings{TamaldinEschTonolietal.2020,
  author    = {Tamaldin, Noreffendy and Esch, Thomas and Tonoli, Andrea and Reisinger, Karl Heinz and Sprenger, Hanna and Razuli, Hisham},
  title     = {ERASMUS+ United CBHE Automotive International Collaboration from European to South East Asia},
  series = {Proceedings of the 2nd African International Conference on Industrial Engineering and Operations Management},
  booktitle = {Proceedings of the 2nd African International Conference on Industrial Engineering and Operations Management},
  publisher = {IEOM Society International},
  address   = {Southfield},
  isbn      = {978-1-7923-6123-4},
  issn      = {2169-8767},
  pages     = {2970 -- 2972},
  year      = {2020},
  abstract  = {The industrial revolution especially in the IR4.0 era have driven many states of the art technologies to be introduced. The automotive industry as well as many other key industries have also been greatly influenced. The rapid development of automotive industries in Europe have created wide industry gap between European Union (EU) and developing countries such as in South East Asia (SEA). Indulging this situation, FH JOANNEUM, Austria together with European partners from FH Aachen, Germany and Politecnico di Torino, Italy are taking initiative to close down the gap utilizing the Erasmus+ United Capacity Building in Higher Education grant from EU. A consortium was founded to engage with automotive technology transfer using the European framework to Malaysian, Indonesian and Thailand Higher Education Institutions (HEI) as well as automotive industries in respective countries. This could be achieved by establishing Engineering Knowledge Transfer Unit (EKTU) in respective SEA institutions guided by the industry partners in their respective countries. This EKTU could offer updated, innovative and high-quality training courses to increase graduate's employability in higher education institutions and strengthen relations between HEI and the wider economic and social environment by addressing University-industry cooperation which is the regional priority for Asia. It is expected that, the Capacity Building Initiative would improve the quality of higher education and enhancing its relevance for the labor market and society in the SEA partners. The outcome of this project would greatly benefit the partners in strong and complementary partnership targeting the automotive industry and enhanced larger scale international cooperation between the European and SEA partners. It would also prepare the SEA HEI in sustainable partnership with Automotive industry in the region as a mean of income generation in the future.},
  language  = {en}
}
@inproceedings{StrieganStruthDickhoffetal.2019,
  author    = {Striegan, Constantin J. D. and Struth, Benjamin and Dickhoff, Jens and Kusterer, Karsten and Funke, Harald and Bohn, Dieter},
  title     = {Numerical Simulations of the Micromix DLN Hydrogen Combustion Technology with LES and Comparison to Results of RANS and Experimental Data},
  series = {Proceedings of International Gas Turbine Congress 2019 Tokyo, November 17-22, 2019, Tokyo, Japan.},
  booktitle = {Proceedings of International Gas Turbine Congress 2019 Tokyo, November 17-22, 2019, Tokyo, Japan.},
  isbn      = {978-4-89111-010-9},
  pages     = {1 -- 9},
  year      = {2019},
  language  = {en}
}
@inproceedings{StrieganHajAyedFunkeetal.2017,
  author    = {Striegan, C. and Haj Ayed, A. and Funke, Harald and Loechle, S. and Kazari, M. and Horikawa, A. and Okada, K. and Koga, K.},
  title     = {Numerical combustion and heat transfer simulations and validation for a hydrogen fueled "micromix" test combustor in industrial gas turbine applications},
  series = {Proceedings of the ASME Turbo Expo},
  booktitle = {Proceedings of the ASME Turbo Expo},
  number    = {Volume Part F130041-4B, 2017},
  isbn      = {978-079185085-5},
  doi       = {10.1115/GT2017-64719},
  year      = {2017},
  language  = {en}
}
@inproceedings{SpurmannOhndorfDachwaldetal.2009,
  author    = {Spurmann, J{\"o}rn and Ohndorf, Andreas and Dachwald, Bernd and Seboldt, Wolfgang and L{\"o}b, Horst and Schartner, Karl-Heinz},
  title     = {Interplanetary trajectory optimization for a sep mission to Saturn},
  series = {60th International Astronautical Congress 2009},
  booktitle = {60th International Astronautical Congress 2009},
  isbn      = {9781615679089},
  pages     = {5234 -- 5248},
  year      = {2009},
  abstract  = {The recently proposed NASA and ESA missions to Saturn and Jupiter pose difficult tasks to mission designers because chemical propulsion scenarios are not capable of transferring heavy spacecraft into the outer solar system without the use of gravity assists. Thus our developed mission scenario based on the joint NASA/ESA Titan Saturn System Mission baselines solar electric propulsion to improve mission flexibility and transfer time. For the calculation of near-globally optimal low-thrust trajectories, we have used a method called Evolutionary Neurocontrol, which is implemented in the low-thrust trajectory optimization software InTrance. The studied solar electric propulsion scenario covers trajectory optimization of the interplanetary transfer including variations of the spacecraft's thrust level, the thrust unit's specific impulse and the solar power generator power level. Additionally developed software extensions enabled trajectory optimization with launcher-provided hyperbolic excess energy, a complex solar power generator model and a variable specific impulse ion engine model. For the investigated mission scenario, Evolutionary Neurocontrol yields good optimization results, which also hold valid for the more elaborate spacecraft models. Compared to Cassini/Huygens, the best found solutions have faster transfer times and a higher mission flexibility in general.},
  language  = {en}
}
@inproceedings{SpohrSchirraHoeflingetal.2013,
  author    = {Spohr, A. and Schirra, Julian and Hoefling, J. and Schedl, A.},
  title     = {Wing weight estimation methodology for highly non-planar lifting systems during conceptual design},
  series = {Deutscher Luft- und Raumfahrtkongress 2013 : 10.9. - 12.9.2013, Stuttgart},
  booktitle = {Deutscher Luft- und Raumfahrtkongress 2013 : 10.9. - 12.9.2013, Stuttgart},
  organization    = {Deutscher Luft- und Raumfahrtkongress <62, 2013, Stuttgart>},
  pages     = {Publ. online},
  year      = {2013},
  language  = {en}
}
@inproceedings{SeefeldtBauerDachwaldetal.2015,
  author    = {Seefeldt, Patric and Bauer, Waldemar and Dachwald, Bernd and Grundmann, Jan Thimo and Straubel, Marco and Sznajder, Maciej and T{\´o}th, Norbert and Zander, Martin E.},
  title     = {Large lightweight deployable structures for planetary defence: solar sail propulsion, solar concentrator payloads, large-scale photovoltaic power},
  series = {4th IAA Planetary Defense Conference - PDC 2015, 13-17 April 2015, Frascati, Roma, Italy},
  booktitle = {4th IAA Planetary Defense Conference - PDC 2015, 13-17 April 2015, Frascati, Roma, Italy},
  pages     = {24},
  year      = {2015},
  language  = {en}
}
@inproceedings{SeboldtDachwald2003,
  author    = {Seboldt, Wolfgang and Dachwald, Bernd},
  title     = {Solar sails for near-term advanced scientific deep space missions},
  series = {Proceedings of the 8th International Workshop on Combustion and Propulsion},
  booktitle = {Proceedings of the 8th International Workshop on Combustion and Propulsion},
  pages     = {14 Seiten},
  year      = {2003},
  abstract  = {Solar sails are propelled in space by reflecting solar photons off large mirroring surfaces, thereby transforming the momentum of the photons into a propulsive force. This innovative concept for low-thrust space propulsion works without any propellant and thus provides a wide range of opportunities for highenergy low-cost missions. Offering an efficient way of propulsion, solar sailcraft could close a gap in transportation options for highly demanding exploration missions within our solar system and even beyond. On December 17th, 1999, a significant step was made towards the realization of this technology: a lightweight solar sail structure with an area of 20 m × 20 m was successfully deployed on ground in a large facility at the German Aerospace Center (DLR) at Cologne. The deployment from a package of 60 cm × 60 cm × 65 cm with a total mass of less than 35 kg was achieved using four extremely light-weight carbon fiber reinforced plastics (CFRP) booms with a specific mass of 100 g/m. The paper briefly reviews the basic principles of solar sails as well as the technical concept and its realization in the ground demonstration experiment, performed in close cooperation between DLR and ESA. Next possible steps are outlined. They could comprise the in-orbit demonstration of the sail deployment on the upper stage of a low-cost rocket and the verification of the propulsion concept by an autonomous and free flying solar sail in the frame of a scientific mission. It is expected that the present design could be extended to sail sizes of about (40 m)2 up to even (70 m)2 without significant mass penalty. With these areas, the maximum achievable thrust at 1 AU would range between 10 and 40 mN - comparable to some electric thrusters. Such prototype sails with a mass between 50 and 150 kg plus a micro-spacecraft of 50 to 250 kg would have a maximum acceleration in the order of 0.1 mm/s2 at 1 AU, corresponding to a maximum ∆V-capability of about 3 km/s per year. Two near/medium-term mission examples to a near-Earth asteroid (NEA) will be discussed: a rendezvous mission and a sample return mission.},
  language  = {en}
}
@inproceedings{SeboldtBlomeDachwaldetal.2004,
  author    = {Seboldt, Wolfgang and Blome, Hans-Joachim and Dachwald, Bernd and Richter, Lutz},
  title     = {Proposal for an integrated European space exploration strategy},
  series = {55th International Astronautical Congress of the International Astronautical Federation, the International Academy of Astronautics, and the International Institute of Space Law},
  booktitle = {55th International Astronautical Congress of the International Astronautical Federation, the International Academy of Astronautics, and the International Institute of Space Law},
  pages     = {1 -- 10},
  year      = {2004},
  abstract  = {Recently, in his vision for space exploration, US president Bush announced to extend human presence across the solar system, starting with a human return to the Moon as early as 2015 in preparation for human exploration of Mars and other destinations. In Europe, an exploration program, termed AURORA, was established by ESA in 2001 - funded on a voluntary basis by ESA member states - with a clear focus on Mars and the ultimate goal of landing humans on Mars around 2030 in international cooperation. In 2003, a Human Spaceflight Vision Group was appointed by ESA with the task to develop a vision for the role of human spaceflight during the next quarter of the century. The resulting vision focused on a European-led lunar exploration initiative as part of a multi-decade, international effort to strengthen European identity and economy. After a review of the situation in Europe concerning space exploration, the paper outlines an approach for a consistent positioning of exploration within the existing European space programs, identifies destinations, and develops corresponding scenarios for an integrated strategy, starting with robotic missions to the Moon, Mars, and near-Earth asteroids. The interests of the European planetary in-situ science community, which recently met at DLR Cologne, are considered. Potential robotic lunar missions comprise polar landings to search for frozen volatiles and a sample return. For Mars, the implementation of a modest robotic landing mission in 2009 to demonstrate the capability for landing and prepare more ambitious and complex missions is discussed. For near-Earth asteroid exploration, a low-cost in-situ technology demonstration mission could yield important results. All proposed scenarios offer excellent science and could therefore create synergies between ESA's mandatory and optional programs in the area of planetary science and exploration. The paper intents to stimulate the European discussion on space exploration and reflects the personal view of the authors.},
  language  = {en}
}
@inproceedings{SchulzeMuehleisenFeyerl2018,
  author    = {Schulze, Sven and M{\"u}hleisen, M. and Feyerl, G{\"u}nter},
  title     = {Adaptive energy management strategy for a heavy-duty truck with a P2-hybrid topology},
  series = {18. Internationales Stuttgarter Symposium. Proceedings},
  booktitle = {18. Internationales Stuttgarter Symposium. Proceedings},
  publisher = {Springer Vieweg},
  address   = {Wiesbaden},
  doi       = {10.1007/978-3-658-21194-3},
  pages     = {75 -- 89},
  year      = {2018},
  language  = {en}
}
@inproceedings{SchoutetensDachwaldHeiligers2021,
  author    = {Schoutetens, Frederic and Dachwald, Bernd and Heiligers, Jeannette},
  title     = {Optimisation of photon-sail trajectories in the alpha-centauri system using evolutionary neurocontrol},
  series = {8th ICATT (International Conference on Astrodynamics Tools and Techniques) 23 - 25 June 2021, Virtual},
  booktitle = {8th ICATT (International Conference on Astrodynamics Tools and Techniques) 23 - 25 June 2021, Virtual},
  pages     = {1 -- 15},
  year      = {2021},
  abstract  = {With the increased interest for interstellar exploration after the discovery of exoplanets and the proposal by Breakthrough Starshot, this paper investigates the optimisation of photon-sail trajectories in Alpha Centauri. The prime objective is to find the optimal steering strategy for a photonic sail to get captured around one of the stars after a minimum-time transfer from Earth. By extending the idea of the Breakthrough Starshot project with a deceleration phase upon arrival, the mission's scientific yield will be increased. As a secondary objective, transfer trajectories between the stars and orbit-raising manoeuvres to explore the habitable zones of the stars are investigated. All trajectories are optimised for minimum time of flight using the trajectory optimisation software InTrance. Depending on the sail technology, interstellar travel times of 77.6-18,790 years can be achieved, which presents an average improvement of 30\% with respect to previous work. Still, significant technological development is required to reach and be captured in the Alpha-Centauri system in less than a century. Therefore, a fly-through mission arguably remains the only option for a first exploratory mission to Alpha Centauri, but the enticing results obtained in this work provide perspective for future long-residence missions to our closest neighbouring star system.},
  language  = {en}
}
@inproceedings{SchopenShabaniEschetal.2022,
  author    = {Schopen, Oliver and Shabani, Bahman and Esch, Thomas and Kemper, Hans and Shah, Neel},
  title     = {Quantitative evaluation of health management designs for fuel cell systems in transport vehicles},
  series = {2nd UNITED-SAIG International Conference Proceedings},
  booktitle = {2nd UNITED-SAIG International Conference Proceedings},
  editor    = {Rahim, S.A. and As'arry, A. and Zuhri, M.Y.M. and Harmin, M.Y. and Rezali, K.A.M. and Hairuddin, A.A.},
  pages     = {1 -- 3},
  year      = {2022},
  abstract  = {Focusing on transport vehicles, mainly with regard to aviation applications, this paper presents compilation and subsequent quantitative evaluation of methods aimed at building an optimum integrated health management solution for fuel cell systems. The methods are divided into two different main types and compiled in a related scheme. Furthermore, different methods are analysed and evaluated based on parameters specific to the aviation context of this study. Finally, the most suitable method for use in fuel cell health management systems is identified and its performance and suitability is quantified.},
  language  = {en}
}
@inproceedings{SchopenKemperEsch2021,
  author    = {Schopen, Oliver and Kemper, Hans and Esch, Thomas},
  title     = {Development of a comparison methodology and evaluation matrix for electrically driven compressors in ICE and FC},
  series = {Proceedings of the 1st UNITED - Southeast Asia Automotive Interest Group (SAIG) International Conference},
  booktitle = {Proceedings of the 1st UNITED - Southeast Asia Automotive Interest Group (SAIG) International Conference},
  publisher = {FH Joanneum},
  address   = {Graz},
  isbn      = {978-3-902103-94-9},
  pages     = {45 -- 46},
  year      = {2021},
  abstract  = {In addition to electromobility and alternative drive systems, a focus is set on electrically driven compressors (EDC), with a high potential for increasing the efficiency of internal combustion engines (ICE) and fuel cells [01]. The primary objective is to increase the ICE torque, provided independently of the ICE speed by compressing the intake air and consequently the ICE filling level supported by the compressor. For operation independent from the ICE speed, the EDC compressor is decoupled from the turbine by using an electric compressor motor (CM) instead of the turbine. ICE performances can be increased by the use of EDC where individual compressor parameters are adapted to the respective application area [02] [03]. This task contains great challenges, increased by demands with regard to pollutant reduction while maintaining constant performance and reduced fuel consumption. The FH-Aachen is equipped with an EDC test bench which enables EDC-investigations in various configurations and operating modes. Characteristic properties of different compressors can be determined, which build the basis for a comparison methodology. Subject of this project is the development of a comparison methodology for EDC with an associated evaluation method and a defined overall evaluation method. For the application of this comparison methodology, corresponding series of measurements are carried out on the EDC test bench using an appropriate test device.},
  language  = {en}
}
@inproceedings{SchleupenEngemannBagherietal.2016,
  author    = {Schleupen, Josef and Engemann, Heiko and Bagheri, Mohsen and Kallweit, Stephan},
  title     = {The potential of SMART climbing robot combined with a weatherproof cabin for rotor blade maintenance},
  series = {17th European Conference on Composite Materials - ECCM, Munich, Germany},
  booktitle = {17th European Conference on Composite Materials - ECCM, Munich, Germany},
  pages     = {1 -- 8},
  year      = {2016},
  language  = {en}
}
@inproceedings{SchirraWatmuffBauschat2014,
  author    = {Schirra, Julian and Watmuff, Jon and Bauschat, J.-Michael},
  title     = {A relative assessment of existing potential-methodologies to accurately estimate the induced drag of highly non-planar lifting systems},
  series = {Advanced aero concepts, design and operations : Applied Aerodynamics Conference : July 22 -24, 2014, Bristol, UK},
  booktitle = {Advanced aero concepts, design and operations : Applied Aerodynamics Conference : July 22 -24, 2014, Bristol, UK},
  organization    = {Applied Aerodynamics Conference <2014, Bristol>},
  pages     = {1 -- 13},
  year      = {2014},
  language  = {en}
}
@inproceedings{SchirraJ2013,
  author    = {Schirra, Julian and J., Watmuff},
  title     = {Euler-based induced drag estimation for highly non-planar lifting systems during conceptional design},
  series = {62. Deutscher Luft- und Raumfahrtkongress 2013 : 10. - 12. September 2032, Stuttgart, Haus der Wirtschaft},
  booktitle = {62. Deutscher Luft- und Raumfahrtkongress 2013 : 10. - 12. September 2032, Stuttgart, Haus der Wirtschaft},
  publisher = {Dt. Gesellschaft f{\"u}r Luft- und Raumfahrt},
  address   = {Bonn},
  organization    = {Deutsche Gesellschaft f{\"u}r Luft- und Raumfahrt - Lilienthal-Oberth},
  pages     = {1 -- 8},
  year      = {2013},
  language  = {en}
}
@inproceedings{SchirraBauschatWatmuff2014,
  author    = {Schirra, Julian and Bauschat, J.-Michael and Watmuff, J.H.},
  title     = {Accurate induced drag prediction for highly non-planar lifting systems},
  series = {19th Australasian Fluid Mechanics Conference : 8.-11. Dezember 2014, Melbourne, Australia},
  booktitle = {19th Australasian Fluid Mechanics Conference : 8.-11. Dezember 2014, Melbourne, Australia},
  pages     = {4 Seiten},
  year      = {2014},
  abstract  = {The impact of wake model effects is investigated for two highly non-planar lifting systems. Dependent on the geometrical arrangement of the configuration, the wake model shape is found to considerably affect the estimation. Particularly at higher angles of attack, an accurate estimation based on the common linear wake model approaches is involved.},
  language  = {en}
}
@inproceedings{SchildtMarzoccaBraunetal.2019,
  author    = {Schildt, Philipp and Marzocca, Pier and Braun, Carsten and Dahmann, Peter and Keimer, Jona},
  title     = {Effects of atmospheric excitation on vibration based condition monitoring methods for hybrid-electric aircraft propulsion systems},
  series = {AIAC 2018: 18th Australian International Aerospace Congress: HUMS - 11th Defence Science and Technology (DST) International Conference on Health and Usage Monitoring (HUMS 2019): ISSFD - 27th International Symposium on Space Flight Dynamics (ISSFD)},
  booktitle = {AIAC 2018: 18th Australian International Aerospace Congress: HUMS - 11th Defence Science and Technology (DST) International Conference on Health and Usage Monitoring (HUMS 2019): ISSFD - 27th International Symposium on Space Flight Dynamics (ISSFD)},
  isbn      = {9781925627213},
  pages     = {923 -- 928},
  year      = {2019},
  language  = {en}
}
@inproceedings{SchildtBraunMarcocca2017,
  author    = {Schildt, P. and Braun, Carsten and Marcocca, P.},
  title     = {Flight testing the extra 330LE flying testbed},
  series = {48th Annual International Symposium of the Society of Flight Test Engineers 2017},
  booktitle = {48th Annual International Symposium of the Society of Flight Test Engineers 2017},
  isbn      = {978-151085387-4},
  pages     = {349 -- 362},
  year      = {2017},
  language  = {en}
}
@inproceedings{SchartnerLoebDachwaldetal.2009,
  author    = {Schartner, Karl-Heinz and Loeb, H. W. and Dachwald, Bernd and Ohndorf, Andreas},
  title     = {Perspectives of electric propulsion for outer planetary and deep space missions},
  series = {European Planetary Science Congress 2009},
  booktitle = {European Planetary Science Congress 2009},
  pages     = {416 -- 416},
  year      = {2009},
  abstract  = {Solar-electric propulsion (SEP) is superior with respect to payload capacity, flight time and flexible launch window to the conventional interplanetary transfer method using chemical propulsion combined with gravity assists. This fact results from the large exhaust velocities of electric low-thrust propulsion and is favourable also for missions to the giant planets, Kuiper-belt objects and even for a heliopause probe (IHP) as shown in three studies by the authors funded by DLR. They dealt with a lander for Europa and a sample return mission from a mainbelt asteroid [1], with the TANDEM mission [2]; the third recent one investigates electric propulsion for the transfer to the edge of the solar system. All studies are based on triple-junction solar arrays, on rf-ion thrusters of the qualified RIT-22 type and they use the intelligent trajectory optimization program InTrance [3].},
  language  = {en}
}
@inproceedings{RoethTragsdorf2004,
  author    = {R{\"o}th, Thilo and Tragsdorf, Carsten},
  title     = {Innovativer Einsatz von Werkstoffen - Trends und Entwicklungen im Karosserieleichtbau},
  year      = {2004},
  abstract  = {1) In Karosseriestrukturen steht der richtige Werkstoffeinsatz st{\"a}rker den je im Spannungsfeld von Leichtbau, Kosten (St{\"u}ckzahlen) und Leistungsanforderung 2) In „klassischen" Strukturen von Modultr{\"a}gern und Klappen hat sich die Materialmischbauweise verst{\"a}rkt in den letzten Jahren durchgesetzt 3) Unter Aspekten des konzeptionellen Leichtbaus erscheint der verst{\"a}rkte Einsatz von Leichtbauwerkstoffen im Vorderwagen sowie in der Dachstruktur zielf{\"u}hrend 4) Offene Strukturprofile in Materialmischbauweise liefern f{\"u}r eine Vielzahl von Anwendungen ein interessantes und bis dato kaum genutztes Potential 5) Neue Entwicklungen bei den F{\"u}getechnologien (i.b. kontinuierliche F{\"u}geverbindungen und kombinierte Verfahren) unterst{\"u}tzen den wirtschaftlichen Karosserieleichtbau 6) Werkstoffinnovationen sowie neuartige Fertigungsverfahren machen den Konstruktionswerkstoff „Stahl" auch in der Zukunft im Karosseriebau weiterhin sehr attraktiv},
  subject      = {Karosseriebau},
  language  = {de}
}
@inproceedings{RoethStark2009,
  author    = {R{\"o}th, Thilo and Stark, R.},
  title     = {Die Rolle der virtuellen Produktentstehung bei der Integration von Karosseriesystemen},
  series = {Karosseriekongress Systemintegration in der Karosserietechnik : 17. und 18. M{\"a}rz 2009 in Baden-Baden / Kongressleitung: Reiner Stark},
  booktitle = {Karosseriekongress Systemintegration in der Karosserietechnik : 17. und 18. M{\"a}rz 2009 in Baden-Baden / Kongressleitung: Reiner Stark},
  publisher = {VDI-Wissensforum},
  address   = {D{\"u}sseldorf},
  isbn      = {978-3-9812624-4-5},
  pages     = {175 S. : zahlr. Ill., graph. Darst.},
  year      = {2009},
  language  = {de}
}
@inproceedings{Roeth2002,
  author    = {R{\"o}th, Thilo},
  title     = {Modularisierung in der Karosserie von morgen},
  year      = {2002},
  abstract  = {1) Module werden die Fahrzeugplattform und den -aufbau in Zukunft weiterhin und in zunehmendem Maße bestimmen. 2) Neue Module und Modulschnittstellen am Fahrzeug werden {\"u}berdacht und k{\"o}nnen in der Zukunft erwartet werden. 3) Die Wertsch{\"o}pfung und der Entwicklungsumfang wird sich vom OEM zum Modullieferanten verlagern. 4) Modulvergaben werden in der Zukunft noch st{\"a}rker auf Innovation und Kostenreduktion beruhen. 5) Modularisierung des Fahrzeuges heißt ein Aufbrechen der Fahrzeugkarosserie und wird daher von der Beherrschung struktureller Aufgaben sowie der L{\"o}sung der (sichtbaren) Modul{\"u}berg{\"a}nge bestimmt sein. 6) Neben den Systemintegratoren und den Komponentenspezialisten besetzen die Modullieferanten die erste Lieferantenriege. 7) Der Modullieferant wird neben h{\"o}chster Fertigungsexpertise ein hohes Maß an (Teil-)fahrzeug-Know-How und Produktentwickler-mentalit{\"a}t bereitstellen.},
  subject      = {Karosseriebau},
  language  = {de}
}
@inproceedings{RuppKuperjansSchulze2016,
  author    = {Rupp, Matthias and Kuperjans, Isabel and Schulze, Sven},
  title     = {Energetische und {\"o}kologische Bewertung hybrider Antriebe im st{\"a}dtischen Busverkehr},
  series = {Commercial vehicle technology 2016 : proceedings of the 4th Commercial Vehicle Technology Symposium (CVT 2016), March 8-10, 2016, University of Kaiserslautern, Kaiserslautern, Germany},
  booktitle = {Commercial vehicle technology 2016 : proceedings of the 4th Commercial Vehicle Technology Symposium (CVT 2016), March 8-10, 2016, University of Kaiserslautern, Kaiserslautern, Germany},
  editor    = {Berns, Karsten},
  publisher = {Shaker},
  address   = {Aachen},
  organization    = {Internationales Commercial Vehicle Technology Symposium <4, 2016, Kaiserslautern>},
  pages     = {227 -- 237},
  year      = {2016},
  abstract  = {In Anbetracht weltweit zunehmend strengerer klimapolitischer Ziele steigt auch der Druck f{\"u}r Nutzfahrzeughersteller, effizientere und umweltfreundlichere Technologien zu entwickeln. Den Blick bei der Bewertung dieser ausschließlich auf die Fahrzeugnutzung zu richten, ist l{\"a}ngst nicht mehr zufriedenstellend. Im Rahmen dieser Analyse wird ein gegenw{\"a}rtig auf dem Markt erwerblicher und in deutschen St{\"a}dten bereits seit Jahren betriebener Hybridbus energetisch und {\"o}kologisch mit einem konventionell angetriebenen, nahezu baugleichen Modell entlang des Lebensweges bewertet. Nach Definition von Ziel und Untersuchungsrahmen wird ein {\"U}berblick auf bereits durchgef{\"u}hrte Lebenszyklusanalysen zu Hybridbussen im Stadtverkehr gegeben und Schlussfolgerungen f{\"u}r die anschließende Analyse abgeleitet. Diese wird im Rahmen einer energetischen und {\"o}kologischen Bewertung beider Produktsysteme anhand der Parameter "Prim{\"a}renergieeinsatz" und "CO2{\"a}q Emissionen" praktiziert. Der Fahrzeugrumpf beider Fahrzeuge des gleichen Modells wird dabei als einheitlich angenommen, sodass bei dem Vergleich der Herstellung vereinfacht nur die sich unterscheidenden Komponenten des Antriebstranges ber{\"u}cksichtigt werden. Die Resultate der Wirkungsabsch{\"a}tzung werden als Differenz des Hybridbusses gegen{\"u}ber dem Referenzfahrzeug {\"u}ber die einzelnen Lebenszyklusphasen dargestellt. Schließlich werden Prognosen getroffen, ab welcher Strecke die bei der Herstellung erzeugten h{\"o}heren CO2{\"a}q Emissionen des Hybridantriebstranges gegen{\"u}ber dem Referenzmodell ausgeglichen werden.},
  language  = {de}
}
@inproceedings{Rosenkranz1993,
  author    = {Rosenkranz, Josef},
  title     = {Verbesserung der Laufruhe des Verbrennungsmotors durch abgestimmte qualit{\"a}tssteigernde Maßnahmen beim Auswuchten des Kurbeltriebs},
  series = {Antriebstechnisches Kolloquium '93 / Industrieentwicklungen und Forschungsergebnisse f{\"u}r die Maschinen{\"u}berwachung und die Konstruktion in der Antriebstechnik. - (Reihe IME-Leitfaden)},
  booktitle = {Antriebstechnisches Kolloquium '93 / Industrieentwicklungen und Forschungsergebnisse f{\"u}r die Maschinen{\"u}berwachung und die Konstruktion in der Antriebstechnik. - (Reihe IME-Leitfaden)},
  publisher = {Verl. T{\"U}V Rheinland},
  address   = {K{\"o}ln},
  isbn      = {3-8249-0139-0},
  pages     = {176 -- 199},
  year      = {1993},
  language  = {de}
}
@inproceedings{RoosenFeyerl2015,
  author    = {Roosen, Petra and Feyerl, G{\"u}nter},
  title     = {Gender-specific perception and utilization of personal use vehicles},
  series = {FISITA World Automotive Congress 2014 : Maastricht, The Netherlands, 2 - 6 June / [organised by the International Federation of Automotive Engineering Societies (FISITA) ...]. Bd. 1},
  booktitle = {FISITA World Automotive Congress 2014 : Maastricht, The Netherlands, 2 - 6 June / [organised by the International Federation of Automotive Engineering Societies (FISITA) ...]. Bd. 1},
  publisher = {Curran},
  address   = {Red Hook, NY},
  isbn      = {978-1-5108-0209-4},
  pages     = {418 -- 425},
  year      = {2015},
  language  = {en}
}
@inproceedings{RingsLudowicyFingeretal.2019,
  author    = {Rings, Ren{\´e} and Ludowicy, Jonas and Finger, Felix and Braun, Carsten and Bil, Cees},
  title     = {Sensitivity Analysis of General Aviation Aircraft with Parallel Hybrid-Electric Propulsion Systems},
  series = {Asia Pacific International Symposium on Aerospace Technology. APISAT 2019},
  booktitle = {Asia Pacific International Symposium on Aerospace Technology. APISAT 2019},
  pages     = {14 Seiten},
  year      = {2019},
  language  = {en}
}
@inproceedings{ReimerBraunChenetal.2007,
  author    = {Reimer, Lars and Braun, Carsten and Chen, B.-H. and Ballmann, Josef},
  title     = {Computational aeroelastic analysis and design of the HIRENASD wind tunnel wing model and tests},
  series = {Proceedings / IFASD 2007, CEAS/AIAA/KTH International Forum on Aeroelasticity and Structural Dynamics : June 18 - 21, 2007, Stockholm, Sweden},
  booktitle = {Proceedings / IFASD 2007, CEAS/AIAA/KTH International Forum on Aeroelasticity and Structural Dynamics : June 18 - 21, 2007, Stockholm, Sweden},
  publisher = {KTH},
  address   = {Stockholm},
  pages     = {1 CD-ROM},
  year      = {2007},
  language  = {en}
}
@inproceedings{ReimerBraunBallmann2006,
  author    = {Reimer, Lars and Braun, Carsten and Ballmann, Josef},
  title     = {Analysis of the static and dynamic aero-structural response of an elastic swept wing model by direct aeroelastic simulation},
  series = {ICAS 2006 proceedings : 25th Congress of the International Council of the Aeronautical Sciences ; Hamburg, Germany, 3 - 8 September, 2006 : 25th International Congress of Aeronautical Sciences},
  booktitle = {ICAS 2006 proceedings : 25th Congress of the International Council of the Aeronautical Sciences ; Hamburg, Germany, 3 - 8 September, 2006 : 25th International Congress of Aeronautical Sciences},
  publisher = {Optimage},
  address   = {Edinburgh},
  organization    = {International Council of the Aeronautical Sciences (ICAS)},
  isbn      = {0-9533991-7-6},
  pages     = {Paper No. 2006-10.3.3},
  year      = {2006},
  language  = {en}
}
@inproceedings{QuitterMarinoBauschat2019,
  author    = {Quitter, Julius and Marino, Matthew and Bauschat, J.-Michael},
  title     = {Highly Non-Planar Aircraft Configurations: Estimation of Flight Mechanical Derivatives Using Low-Order Methods},
  series = {Deutscher Luft- und Raumfahrtkongress 2019, DLRK 2019. Darmstadt, Germany},
  booktitle = {Deutscher Luft- und Raumfahrtkongress 2019, DLRK 2019. Darmstadt, Germany},
  pages     = {10 Seiten},
  year      = {2019},
  language  = {en}
}
@inproceedings{PlescherMathiakWillnecker2005,
  author    = {Plescher, Engelbert and Mathiak, Gerhard and Willnecker, Rainer},
  title     = {Technical aspects of liquid diffusion model experiments},
  series = {55th International Astronautical Congress : October 4 - 8, 2004, Vancouver, Canada / International Astronautical Federation. Bd. 8. IAC-04-J.5.04},
  booktitle = {55th International Astronautical Congress : October 4 - 8, 2004, Vancouver, Canada / International Astronautical Federation. Bd. 8. IAC-04-J.5.04},
  publisher = {International Astronautical Federation},
  address   = {Paris},
  organization    = {International Astronautical Congress <55, 2004, Vancouver>},
  pages     = {5019 -- 5025},
  year      = {2005},
  language  = {en}
}
@inproceedings{PirovanoSeefeldtDachwaldetal.2015,
  author    = {Pirovano, Laura and Seefeldt, Patric and Dachwald, Bernd and Noomen, Ron},
  title     = {Attitude and Orbital Dynamics Modeling for an Uncontrolled Solar-Sail Experiment in Low-Earth Orbit},
  series = {25th International Symposium on Spaceflight Dynamics, 2015, Munich, Germany},
  booktitle = {25th International Symposium on Spaceflight Dynamics, 2015, Munich, Germany},
  pages     = {15 S.},
  year      = {2015},
  language  = {en}
}