@inproceedings{WeissAbanteribaEsch2007, author = {Weiss, Alexander and Abanteriba, Sylvester and Esch, Thomas}, title = {Investigation of Flow Separation Inside a Conical Rocket Nozzle With the Aid of an Annular Cross Flow}, series = {Proceedings of the ASME/JSME 2007 5th Joint Fluids Engineering Conference. Volume 1: Symposia, Parts A and B}, booktitle = {Proceedings of the ASME/JSME 2007 5th Joint Fluids Engineering Conference. Volume 1: Symposia, Parts A and B}, publisher = {American Society of Mechanical Engineers (ASME)}, address = {New York}, isbn = {0-7918-4288-6}, doi = {10.1115/FEDSM2007-37387}, pages = {1861 -- 1871}, year = {2007}, abstract = {Flow separation is a phenomenon that occurs in all kinds of supersonic nozzles sometimes during run-up and shut-down operations. Especially in expansion nozzles of rocket engines with large area ratio, flow separation can trigger strong side loads that can damage the structure of the nozzle. The investigation presented in this paper seeks to establish measures that may be applied to alter the point of flow separation. In order to achieve this, a supersonic nozzle was placed at the exit plane of the conical nozzle. This resulted in the generation of cross flow surrounding the core jet flow from the conical nozzle. Due to the entrainment of the gas stream from the conical nozzle the pressure in its exit plane was found to be lower than that of the ambient. A Cold gas instead of hot combustion gases was used as the working fluid. A mathematical simulation of the concept was validated by experiment. Measurements confirmed the simulation results that due to the introduction of a second nozzle the pressure in the separated region of the conical nozzle was significantly reduced. It was also established that the boundary layer separation inside the conical nozzle was delayed thus allowing an increased degree of overexpansion. The condition established by the pressure measurements was also demonstrated qualitatively using transparent nozzle configurations.}, language = {en} } @masterthesis{Weisbecker2023, type = {Bachelor Thesis}, author = {Weisbecker, Helen}, title = {550 nm : Farbwechsel von Tieren - Kommunikation in der Natur}, publisher = {FH Aachen}, address = {Aachen}, school = {Fachhochschule Aachen}, pages = {116 Seiten}, year = {2023}, abstract = {„550 nm" befasst sich mit dem physiologischen Farbwechsel von Tieren. Einige Fische, Amphibien und Reptilien - wie beispielsweise das Cham{\"a}leon oder der Tintenfisch - k{\"o}nnen ihre K{\"o}rperfarbe schnell wechseln. Unsere Natur leidet unter Kriegen und dem Klimawandel und verliert dadurch ihre Sch{\"o}nheit. Diese zeichnet sich vor allem durch die beachtliche Diversit{\"a}t der K{\"o}rperf{\"a}rbung von Tieren aus. Die Funktionen erstrecken sich {\"u}ber Tarnung, Auflauern oder Warnung bis hin zu einer Werbef{\"a}rbung. Nicht nur Tiere nutzen Farbe als Ausdrucks- und Kommunikationsmittel. Auch Designer*innen bedienen sich an Farben, um Stimmungen zu vermitteln oder um Aufmerksamkeit und Individualit{\"a}t zu generieren. In „550 nm" wird das Ph{\"a}nomen des Farbwechsels durch Illustrationen visualisiert und soll als Inspiration f{\"u}r Designinnovationen dienen.}, language = {de} } @techreport{WeisSchornAnthrakidisetal.2016, author = {Weis, Fabian and Schorn, Christian and Anthrakidis, Anette and Herrmann, Ulf}, title = {Entwicklung eines kleinen Parabolrinnenkollektors mit Kunststoffkorpus zur Bereitstellung solarer Prozessw{\"a}rme : Poly-P : Abschlussbericht}, publisher = {Solar-Institut J{\"u}lich}, address = {J{\"u}lich}, pages = {56 Seiten}, year = {2016}, language = {de} } @inproceedings{WeingartSchneiderWollert2009, author = {Weingart, Daniel and Schneider, Ulf and Wollert, J{\"o}rg}, title = {Doppelt gekoppelt - Kabellose und dynamische Anbindung von CANopen an Profinet IO}, series = {Elektrische Automatisierung - Systeme und Komponenten: SPS-IPC-Drives 2009, Fachmesse \& Kongress, 24. - 26. Nov. 2009, N{\"u}rnberg ; [Tagungsband]}, booktitle = {Elektrische Automatisierung - Systeme und Komponenten: SPS-IPC-Drives 2009, Fachmesse \& Kongress, 24. - 26. Nov. 2009, N{\"u}rnberg ; [Tagungsband]}, publisher = {VDE-Verl.}, address = {Berlin [u.a.]}, isbn = {978-3-8007-3184-8}, pages = {147 -- 154}, year = {2009}, language = {de} } @inproceedings{WeilPoghossianSchoeningetal.2012, author = {Weil, M. and Poghossian, Arshak and Sch{\"o}ning, Michael Josef and Cherstvy, A.}, title = {Electrical monitoring of layer-by-layer adsorption of oppositely charged macromolecules by means of capacitive field-effect devices}, isbn = {978-3-9813484-2-2}, doi = {10.5162/IMCS2012/P2.5.2}, pages = {1575 -- 1578}, year = {2012}, language = {en} } @article{WeiheErnstRoethetal.2013, author = {Weihe, Stefan and Ernst, Ansgar and R{\"o}th, Thilo and Proksch, Johannes}, title = {Aluminium-Stahl-Verbundguss im Nutzfahrzeugbau}, series = {ATZ - Automobiltechnische Zeitschrift}, volume = {115}, journal = {ATZ - Automobiltechnische Zeitschrift}, number = {4}, publisher = {Springer Fachmedien Wiesbaden}, issn = {2192-8800 (Online)}, pages = {312 -- 316}, year = {2013}, abstract = {In modernen Fahrzeugkarosserien der Großserie kommen zunehmend Materialmischbauweisen zur Anwendung. In Zusammenarbeit der Daimler AG, der Tower Automotive Holding GmbH, der Imperia GmbH sowie der Partnerunternehmen KSM Castings GmbH und Schaufler Tooling GmbH \& Co. KG wird das Leichtbaupotenzial von Aluminiumverbundguss-Stahlblech-Hybriden am Beispiel des vorderen Dachquertr{\"a}gers des Mercedes-Benz Viano/Vito ausf{\"u}hrlich untersucht.}, language = {de} } @article{WeiheAnsgarRoethetal.2013, author = {Weihe, Stefan and Ansgar, Ernst and R{\"o}th, Thilo and Proksch, Johannes}, title = {Leichtmetall-Stahl-Verbundguss im Nutzfahrzeugbau}, series = {Lightweight Design}, volume = {6}, journal = {Lightweight Design}, number = {2}, publisher = {Springer}, address = {Berlin}, issn = {2192-8738 (Online)}, pages = {38 -- 43}, year = {2013}, abstract = {In modernen Fahrzeugkarosserien der Großserie kommen zunehmend Materialmischbauweisen zur Anwendung. In Zusammenarbeit der Daimler AG, der Tower Automotive Holding GmbH, der Imperia GmbH sowie der Partnerunternehmen KSM Castings GmbH und Schaufler Tooling GmbH \& Co. KG wird das Leichtbaupotenzial von Stahlblech-AluminiumverbundgussHybriden am Beispiel des vorderen Dachquertr{\"a}gers des Mercedes-Benz Viano/Vito ausf{\"u}hrlich untersucht.}, language = {de} } @article{WeigandCollaniSaniga1994, author = {Weigand, Christoph and Collani, E. v. and Saniga, E.M.}, title = {Economic Adjustment Design for -Control Charts. E.v.Collani, E.M. Saniga, Ch. Weigand}, series = {IIE Transactions / Institute of Industrial Engineers. 26 (1994), H. 6}, journal = {IIE Transactions / Institute of Industrial Engineers. 26 (1994), H. 6}, isbn = {0569-5554}, year = {1994}, language = {en} } @article{Weigand1994, author = {Weigand, Christoph}, title = {Optimal Production Schedule for a K Products Single Machine Problem}, series = {Economic Quality Control. 9 (1994)}, journal = {Economic Quality Control. 9 (1994)}, isbn = {0940-5151}, pages = {91 -- 101}, year = {1994}, language = {en} } @article{Weigand1991, author = {Weigand, Christoph}, title = {Optimale Maschinenjustierung}, series = {Technische Hochschule / Bibliothek: Wissenschaftliche Zeitschrift. 37 (1991)}, journal = {Technische Hochschule / Bibliothek: Wissenschaftliche Zeitschrift. 37 (1991)}, isbn = {0043-6917}, pages = {167 -- 175}, year = {1991}, language = {de} } @article{Weigand1991, author = {Weigand, Christoph}, title = {A Solution to the Scheduling Problem Taking into Account Quality}, series = {Operations research '91 : extended abstracts of the 16th Symposium on Operations Research held at the University of Trier at September 9 - 11, 1991 / [GM{\"O}OR]. Peter Gritzmann ... (eds.)}, journal = {Operations research '91 : extended abstracts of the 16th Symposium on Operations Research held at the University of Trier at September 9 - 11, 1991 / [GM{\"O}OR]. Peter Gritzmann ... (eds.)}, publisher = {Physica-Verl.}, address = {Heidelberg}, isbn = {3790806080}, pages = {373 -- 375}, year = {1991}, language = {en} } @article{Weigand1990, author = {Weigand, Christoph}, title = {Optimal Adjustment Policies}, series = {Proceedings of the First Ume{\aa}-W{\"u}rzburg Conference in Statistics : Kronlund Conference Center and University of Ume{\aa}, September 10 - 14, 1990 / ed. by Kurt Br{\"a}nn{\"a}s}, journal = {Proceedings of the First Ume{\aa}-W{\"u}rzburg Conference in Statistics : Kronlund Conference Center and University of Ume{\aa}, September 10 - 14, 1990 / ed. by Kurt Br{\"a}nn{\"a}s}, publisher = {Univ. of Ume{\aa}}, address = {Ume{\aa}}, isbn = {91-7174-564-5}, pages = {147 -- 158}, year = {1990}, language = {en} } @book{Weigand2006, author = {Weigand, Christoph}, title = {Statistik mit und ohne Zufall : eine anwendungsorientierte Einf{\"u}hrung ; mit 10 Tabellen / Christoph Weigand}, publisher = {Physica-Verl.}, address = {Heidelberg}, isbn = {3-7908-1693-0}, pages = {XIII, 421 S. : graph. Darst.}, year = {2006}, language = {de} } @article{Weigand2003, author = {Weigand, Christoph}, title = {Technically Optimal Inspection Policy with Arithmetical Adaption}, series = {IMA Journal of Management Mathematics. 14 (2003), H. 4}, journal = {IMA Journal of Management Mathematics. 14 (2003), H. 4}, isbn = {1471-678X}, pages = {357 -- 371}, year = {2003}, language = {en} } @article{Weigand2003, author = {Weigand, Christoph}, title = {Economically Optimal Inspection Policy with Geometrical Adaption}, series = {Journal of Applied Statistics. 30 (2003), H. 5}, journal = {Journal of Applied Statistics. 30 (2003), H. 5}, isbn = {0266-4763}, pages = {555 -- 569}, year = {2003}, language = {en} } @article{Weigand2001, author = {Weigand, Christoph}, title = {Economically Optimal Inspection Policy with Arithmetical Adaption}, series = {Applied stochastic models and data analysis / [10th International Symposium on Applied Stochastic Models and Analysis, June 12-15 2001, Universit{\´e} Technologique de Compi{\`e}gne] ; editors G{\´e}rard Govaert, Jacques Janssen, Nikolaos Limnios.}, journal = {Applied stochastic models and data analysis / [10th International Symposium on Applied Stochastic Models and Analysis, June 12-15 2001, Universit{\´e} Technologique de Compi{\`e}gne] ; editors G{\´e}rard Govaert, Jacques Janssen, Nikolaos Limnios.}, publisher = {Universit{\´e} Technologique de Compi{\`e}gne}, address = {Compi{\`e}gne}, pages = {1010 -- 1015}, year = {2001}, language = {en} } @article{Weigand2000, author = {Weigand, Christoph}, title = {Economically Optimal Adaptive Inspection Policies}, series = {Economic Quality Control. 15 (2000), H. 1/2}, journal = {Economic Quality Control. 15 (2000), H. 1/2}, isbn = {0940-5151}, pages = {55 -- 77}, year = {2000}, language = {en} } @article{Weigand1992, author = {Weigand, Christoph}, title = {Economic Machine Adjustment in the Case of Product Screening .E.v.Collani, Ch. Weigand}, series = {Statistical Papers. 33 (1992)}, journal = {Statistical Papers. 33 (1992)}, pages = {171 -- 184}, year = {1992}, language = {en} } @article{Weigand1993, author = {Weigand, Christoph}, title = {On the Effects of SPC on Production Time}, series = {Economic Quality Control. 8 (1993)}, journal = {Economic Quality Control. 8 (1993)}, isbn = {0940-5151}, pages = {23 -- 61}, year = {1993}, language = {en} } @article{Weigand1992, author = {Weigand, Christoph}, title = {A new Approach for Optimal Control of a Production process}, series = {Economic Quality Control. 7 (1992)}, journal = {Economic Quality Control. 7 (1992)}, isbn = {0940-5151}, pages = {225 -- 251}, year = {1992}, language = {en} } @book{Weigand2009, author = {Weigand, Christoph}, title = {Statistik mit und ohne Zufall : Eine anwendungsorientierte Einf{\"u}hrung . 2. Aufl.}, publisher = {Physica-Verlag}, address = {Heidelberg}, isbn = {978-3-7908-2346-2}, pages = {XIII, 469 S. : Ill., graph. Darst.}, year = {2009}, language = {de} } @article{Weigand2009, author = {Weigand, Christoph}, title = {Defining Precisions for Reliable Measurement and Estimation Procedures}, series = {Economic Quality Control. 24 (2009), H. 1}, journal = {Economic Quality Control. 24 (2009), H. 1}, publisher = {De Gruyter}, address = {Berlin}, isbn = {0940-5151}, pages = {5 -- 33}, year = {2009}, language = {en} } @article{Weigand2012, author = {Weigand, Christoph}, title = {Statistical Tests Based on Reliability and Precision}, series = {Economic Quality Control : EQC ; international journal for quality and reliability}, volume = {27}, journal = {Economic Quality Control : EQC ; international journal for quality and reliability}, number = {1}, publisher = {De Gruyter}, address = {Berlin}, issn = {1869-6147}, doi = {10.1515/eqc-2012-0002}, pages = {43 -- 64}, year = {2012}, abstract = {The construction of a statistical test is investigated which is based only on "reliability" and "precision" as quality criteria. The reliability of a statistical test is quantifiedin a straightforward way by the probability that the decision of the test is correct. However, the quantification of the precision of a statistical test is not at all evident. Thereforethe paper presents and discusses several approaches. Moreover the distinction of "nullhypothesis" and "alternative hypothesis" is not necessary any longer.}, language = {en} } @book{Weigand2019, author = {Weigand, Christoph}, title = {Statistik mit und ohne Zufall : Eine anwendungsorientierte Einf{\"u}hrung}, edition = {3. Aufl.}, publisher = {Springer Spektrum}, address = {Berlin, Heidelberg}, isbn = {978-3-662-59309-7}, doi = {10.1007/978-3-662-59309-7}, pages = {499 S.}, year = {2019}, language = {de} } @article{WegnervonArxSassKlaassenetal.2013, author = {Wegner, Lena and von Arx, Georg and Sass-Klaassen, Ute G. W. and Eilmann, Britta}, title = {ROXAS - an efficient and accurate tool to detect vessels in diffuse-porous species}, series = {IAWA Journal / International Association of Wood Anatomists}, volume = {34}, journal = {IAWA Journal / International Association of Wood Anatomists}, number = {4}, publisher = {Brill}, address = {Leiden}, issn = {0928-1541 (Print)}, doi = {10.1163/22941932-00000034}, pages = {425 -- 432}, year = {2013}, language = {en} } @article{WegmannHacklStaatetal.2016, author = {Wegmann, Kilian and Hackl, Michael and Staat, Manfred and Mayer, Katharina and M{\"u}ller, Lars-Peter}, title = {Double plate osteosynthesis of proximal ulna fractures: biomechanical and clinical results}, series = {Knee surgery, sports traumatology, arthroscopy}, volume = {Volume 24}, journal = {Knee surgery, sports traumatology, arthroscopy}, number = {Supplement 1}, publisher = {Springer}, address = {Berlin}, issn = {0942-2056}, doi = {10.1007/s00167-016-4079-0}, pages = {58 -- 59}, year = {2016}, abstract = {While plate fixation of proximal ulna fractures might lead to superior clinical results compared to tension band wiring, regular plates represent an established risk factor for wound complications. The olecranon double plates (Medartis, Basel, CH) might decrease complications related to the osteosynthesis because of their low profile and better anatomical fit. This study aimed to evaluate the biomechanical performance and clinical results of the olecranon double plates.}, language = {en} } @article{WeemstraEilmannSassKlaassenetal.2013, author = {Weemstra, Monique and Eilmann, Britta and Sass-Klaassen, Ute G. W. and Sterck, Frank J.}, title = {Summer droughts limit tree growth across 10 temperate species on a productive forest site}, series = {Forest Ecology and Management}, volume = {2013}, journal = {Forest Ecology and Management}, number = {306}, publisher = {Elsevier}, address = {Amsterdam}, issn = {0378-1127 (Print)}, doi = {doi:10.1016/j.foreco.2013.06.007}, pages = {142 -- 149}, year = {2013}, language = {en} } @article{WedrowskiBruyndonckxTavernieretal.2009, author = {Wedrowski, M. and Bruyndonckx, P. and Tavernier, S. and Zhi, L. and Dang, J. and Mendes, P. R. and Perez, J. M. and Ziemons, Karl}, title = {Robustness of neural networks algorithm for gamma detection in monolithic block detector, positron emission tomography}, series = {2009 IEEE Nuclear Science Symposium Conference Record (NSS/MIC)}, journal = {2009 IEEE Nuclear Science Symposium Conference Record (NSS/MIC)}, isbn = {1082-3654}, pages = {2625 -- 2628}, year = {2009}, abstract = {The monolithic scintillator block approach for gamma detection in the Positron Emission Tomography (PET) avoids estimating Depth of Interaction (DOI), reduces dead zones in detector and diminishes costs of detector production. Neural Networks (NN) are very efficient to determine the entrance point of a gamma incident on a scintillator block. This paper presents results on the robustness of the spatial resolution as a function of the random fraction in the data, temperature and HV fluctuations. This is important when implementing the method in a real scanner. Measurements were done with two Hamamatsu S8550 APD arrays, glued on a 20 {\~A}— 20 {\~A}— 10 mm3 monolithic LSO crystal block.}, language = {en} } @article{WeckesserHufnagelZiemonsetal.1997, author = {Weckesser, Matthias and Hufnagel, Andreas and Ziemons, Karl and Grießmeier, Martin and Sonnenberg, Frank and Hackl{\"a}nder, Thomas and Langen, Karl-J. and Holschbach, Markus and Elger, Christian E. and M{\"u}ller-G{\"a}rtner, Hans-W.}, title = {Effect of partial volume correction on muscarinic cholinergic receptor imaging with single-photon emission tomography in patients with temporal lobe epilepsy}, series = {European Journal of Nuclear Medicine}, volume = {24}, journal = {European Journal of Nuclear Medicine}, number = {9}, isbn = {1619-7089}, pages = {1156 -- 1161}, year = {1997}, abstract = {Animal experiments and preliminary results in humans have indicated alterations of hippocampal muscarinic acetylcholine receptors (mAChR) in temporal lobe epilepsy. Patients with temporal lobe epilepsy often present with a reduction in hippocampal volume. The aim of this study was to investigate the influence of hippocampal atrophy on the quantification of mAChR with single photon emission tomography (SPET) in patients with temporal lobe epilepsy. Cerebral uptake of the muscarinic cholinergic antagonist [123I]4-iododexetimide (IDex) was investigated by SPET in patients suffering from temporal lobe epilepsy of unilateral (n=6) or predominantly unilateral (n=1) onset. Regions of interest were drawn on co-registered magnetic resonance images. Hippocampal volume was determined in these regions and was used to correct the SPET results for partial volume effects. A ratio of hippocampal IDex binding on the affected side to that on the unaffected side was used to detect changes in muscarinic cholinergic receptor density. Before partial volume correction a decrease in hippocampal IDex binding on the focus side was found in each patient. After partial volume no convincing differences remained. Our results indicate that the reduction in hippocampal IDex binding in patients with epilepsy is due to a decrease in hippocampal volume rather than to a decrease in receptor concentration.}, language = {en} } @article{WeckesserGriessmeierSchmidtetal.1998, author = {Weckesser, Martin and Grießmeier, Martin and Schmidt, Daniela and Sonnenberg, Frank and Ziemons, Karl and Kemna, Lars and Holschbach, Marcus and Langen, Karl-J. and M{\"u}ller-G{\"a}rtner, Hans-W.}, title = {Iodine-123 α-methyl tyrosine single-photon emission tomography of cerebral gliomas: standardised evaluation of tumour uptake and extent}, series = {European Journal of Nuclear Medicine}, volume = {25}, journal = {European Journal of Nuclear Medicine}, number = {2}, isbn = {1619-7089}, pages = {150 -- 156}, year = {1998}, abstract = {Single-photon emission tomography (SPET) with the amino acid analogue l-3-[123I]iodo-α-methyl tyrosine (IMT) is helpful in the diagnosis and monitoring of cerebral gliomas. Radiolabelled amino acids seem to reflect tumour infiltration more specifically than conventional methods like magnetic resonance imaging and computed tomography. Automatic tumour delineation based on maximal tumour uptake may cause an overestimation of mean tumour uptake and an underestimation of tumour extension in tumours with circumscribed peaks. The aim of this study was to develop a program for tumour delineation and calculation of mean tumour uptake which takes into account the mean background activity and is thus optimised to the problem of tumour definition in IMT SPET. Using the frequency distribution of pixel intensities of the tomograms a program was developed which automatically detects a reference brain region and draws an isocontour region around the tumour taking into account mean brain radioactivity. Tumour area and tumour/brain ratios were calculated. A three-compartment phantom was simulated to test the program. The program was applied to IMT SPET studies of 20 patients with cerebral gliomas and was compared to the results of manual analysis by three different investigators. Activity ratios and chamber extension of the phantom were correctly calculated by the automatic analysis. A method based on image maxima alone failed to determine chamber extension correctly. Manual region of interest analysis in patient studies resulted in a mean inter-observer standard deviation of 8.7\%±6.1\% (range 2.7\%-25.0\%). The mean value of the results of the manual analysis showed a significant correlation to the results of the automatic analysis (r = 0.91, P<0.0001 for the uptake ratio; r = 0.87, P<0.0001 for the tumour area). We conclude that the algorithm proposed simplifies the calculation of uptake ratios and may be used for observer-independent evaluation of IMT SPET studies. Three-dimensional tumour recognition and transfer to co-registered morphological images based on this program may be useful for the planning of surgical and radiation treatment.}, language = {en} } @inproceedings{WeberTellisDuhovic2016, author = {Weber, Tobias and Tellis, Jane J. and Duhovic, Miro}, title = {Characterization of tool-part-interaction an interlaminar friction for manufacturing process simulation}, series = {ECCM 17, 17th European Conference on Composite Materials, M{\"u}nchen, DE, Jun 26-30, 2016}, booktitle = {ECCM 17, 17th European Conference on Composite Materials, M{\"u}nchen, DE, Jun 26-30, 2016}, isbn = {978-3-00-053387-7}, pages = {1 -- 7}, year = {2016}, language = {en} } @article{WeberRuffStahl2017, author = {Weber, Tobias and Ruff-Stahl, Hans-Joachim K.}, title = {Advances in Composite Manufacturing of Helicopter Parts}, series = {International Journal of Aviation, Aeronautics, and Aerospace}, volume = {4}, journal = {International Journal of Aviation, Aeronautics, and Aerospace}, number = {1}, issn = {2374-6793}, doi = {10.15394/ijaaa.2017.1153}, year = {2017}, language = {en} } @inproceedings{WeberEnglhardHaileretal.2019, author = {Weber, Tobias and Englhard, Markus and Hailer, Benjamin and Arent, Jan-Christoph}, title = {Manufacturing Process Simulation for the Prediction of Tool-Part-Interaction and Ply Wrinkling}, series = {Proceedings of SAMPE Europe Conference 2019, Nantes, France}, booktitle = {Proceedings of SAMPE Europe Conference 2019, Nantes, France}, pages = {1 -- 10}, year = {2019}, language = {en} } @inproceedings{WeberEnglhardHaileretal.2015, author = {Weber, Tobias and Englhard, Markus and Hailer, Benjamin and Arent, Jan-Christoph}, title = {Manufacturing Process Simulation for the Prediction of Tool-Part-Interaction and Ply Wrinkling}, series = {Proceedings of SAMPE Europe Conference, Amiens , France}, booktitle = {Proceedings of SAMPE Europe Conference, Amiens , France}, pages = {1 -- 10}, year = {2015}, language = {en} } @article{WeberEnglhardArentetal.2019, author = {Weber, Tobias and Englhard, Markus and Arent, Jan-Christoph and Hausmann, Joachim}, title = {An experimental characterization of wrinkling generated during prepreg autoclave manufacturing using caul plates}, series = {Journal of Composite Materials}, volume = {53}, journal = {Journal of Composite Materials}, number = {26-27}, issn = {1530-793X}, doi = {10.1177/0021998319846556}, pages = {3757 -- 3773}, year = {2019}, language = {en} } @article{WeberArentSteffenetal.2017, author = {Weber, Tobias and Arent, Jan-Christoph and Steffen, Lucas and Balvers, Johannes M. and Duhovic, Miro}, title = {Thermal optimization of composite autoclave molds using the shift factor approach for boundary condition estimation}, series = {Journal of Composite Materials}, volume = {51}, journal = {Journal of Composite Materials}, number = {12}, publisher = {Sage}, address = {London}, issn = {1530-793X}, doi = {10.1177/0021998317699868}, pages = {1753 -- 1767}, year = {2017}, language = {en} } @article{WeberArentMuenchetal.2016, author = {Weber, Tobias and Arent, Jan-Christoph and M{\"u}nch, Lukas and Duhovic, Miro and Balvers, Johannes M.}, title = {A fast method for the generation of boundary conditions for thermal autoclave simulation}, series = {Composites Part A}, volume = {88}, journal = {Composites Part A}, publisher = {Elsevier}, address = {Amsterdam}, issn = {1359-835X}, doi = {10.1016/j.compositesa.2016.05.036}, pages = {216 -- 225}, year = {2016}, abstract = {Manufacturing process simulation enables the evaluation and improvement of autoclave mold concepts early in the design phase. To achieve a high part quality at low cycle times, the thermal behavior of the autoclave mold can be investigated by means of simulations. Most challenging for such a simulation is the generation of necessary boundary conditions. Heat-up and temperature distribution in an autoclave mold are governed by flow phenomena, tooling material and shape, position within the autoclave, and the chosen autoclave cycle. This paper identifies and summarizes the most important factors influencing mold heat-up and how they can be introduced into a thermal simulation. Thermal measurements are used to quantify the impact of the various parameters. Finally, the gained knowledge is applied to develop a semi-empirical approach for boundary condition estimation that enables a simple and fast thermal simulation of the autoclave curing process with reasonably high accuracy for tooling optimization.}, language = {en} } @inproceedings{Weber2015, author = {Weber, Tobias}, title = {Manufacturing Process Simulation for Tooling Optimization: Reduction of Quality Issues During Autoclave Manufacturing of Composite Parts}, series = {Proceedings of SAMPE Europe Conference 2015, Amiens, France}, booktitle = {Proceedings of SAMPE Europe Conference 2015, Amiens, France}, pages = {1 -- 8}, year = {2015}, language = {en} } @phdthesis{Weber2019, author = {Weber, Tobias}, title = {Herstellprozesssimulation zur Vorhersage der Faltenbildung in der Prepreg-Autoklav-Fertigung}, publisher = {Technische Universit{\"a}t Kaiserslautern}, address = {Kaiserslautern}, isbn = {978-3-944440-24-8}, url = {http://nbn-resolving.de/urn:nbn:de:hbz:386-kluedo-54923}, pages = {XIV, 207 Seiten}, year = {2019}, language = {de} } @inproceedings{WeberTersteggeHallingetal.1995, author = {Weber, S. and Terstegge, Andreas and Halling, H. and Herzog, H. and Reinartz, R. and Reinhart, P. and Rongen, F. and M{\"u}ller-G{\"a}rtner, H.-W.}, title = {The design of an animal PET: flexible geometry for achieving optimal spatial resolution or high sensitivity}, series = {Conference record / 1995 IEEE Nuclear Science Symposium and Medical Imaging, October 21 - 28, 1995, San Francisco ; vol. 2}, booktitle = {Conference record / 1995 IEEE Nuclear Science Symposium and Medical Imaging, October 21 - 28, 1995, San Francisco ; vol. 2}, publisher = {IEEE}, address = {Piscataway, NJ}, organization = {Institute of Electrical and Electronics Engineers}, isbn = {078033180X ; 0780331818 ; 0780331826}, pages = {1002 -- 1005}, year = {1995}, language = {en} } @inproceedings{WeberTersteggeEngelsetal.1996, author = {Weber, S. and Terstegge, Andreas and Engels, R. and Herzog, H. and Reinartz, R. and Reinhart, P. and Rongen, F. and M{\"u}ller-G{\"a}rtner, H. W. and Halling, H.}, title = {The KFA TierPET: performance characteristics and measurements}, series = {Conference record / 1996 IEEE Nuclear Science Symposium [and Medical Imaging], November 2 - 9, 1996, Anaheim, California ; vol. 2}, booktitle = {Conference record / 1996 IEEE Nuclear Science Symposium [and Medical Imaging], November 2 - 9, 1996, Anaheim, California ; vol. 2}, publisher = {IEEE}, address = {Piscataway, NJ}, organization = {Institute of Electrical and Electronics Engineers}, isbn = {0-7803-3534-1}, issn = {1082-3654}, pages = {1117 -- 1119}, year = {1996}, language = {en} } @article{WeberRiglingEilmannetal.2008, author = {Weber, Pascale and Rigling, Andreas and Eilmann, Britta and Mayer, Phillip and Wohlgemuth, Thomas and Dobbertin, Matthias}, title = {Verj{\"u}ngung und Konkurrenz der Flaumeiche im Wallis}, series = {Informationsblatt Wald}, journal = {Informationsblatt Wald}, number = {22}, issn = {1661-5859 (Online)}, pages = {1 -- 3}, year = {2008}, language = {de} } @inproceedings{WeberWolf2017, author = {Weber, Niklas and Wolf, Martin}, title = {Datenerhebung f{\"u}r die CDG-Forschung}, series = {Prozesse, Technologie, Anwendungen, Systeme und Management 2017 : angewandte Forschung in der Wirtschaftsinformatik : Tagungsband zur 30. AKWI-Jahrestagung vom 17.09.2017 bis 20.09.2017 an der Hochschule Aschaffenburg / Arbeitskreis Wirtschaftsinformatik an Fachhochschulen (AKWI)}, booktitle = {Prozesse, Technologie, Anwendungen, Systeme und Management 2017 : angewandte Forschung in der Wirtschaftsinformatik : Tagungsband zur 30. AKWI-Jahrestagung vom 17.09.2017 bis 20.09.2017 an der Hochschule Aschaffenburg / Arbeitskreis Wirtschaftsinformatik an Fachhochschulen (AKWI)}, editor = {Barton, Thomas}, publisher = {mana-Buch}, address = {Heide}, isbn = {978-3-944330-56-3}, pages = {218 -- 227}, year = {2017}, language = {de} } @masterthesis{Weber2021, type = {Bachelor Thesis}, author = {Weber, Jana}, title = {Botanischer Garten und Botanisches Museum Berlin: Entwicklung eines neuen Erscheinungsbildes}, publisher = {FH Aachen}, address = {Aachen}, school = {Fachhochschule Aachen}, pages = {125 Seiten}, year = {2021}, abstract = {Die Pflanzenvielfalt der Erde steht im Fokus aller Aktivit{\"a}ten am Botanischen Garten und Botanischen Museum Berlin (BGBM). Umfangreiche wissenschaftliche Sammlungen bilden zusammen mit den historischen Garten- und Gew{\"a}chshausanlagen, dem Museum und einer modernen Forschungsinfrastruktur die Grundlage f{\"u}r die dortige Arbeit. Dar{\"u}ber hinaus tr{\"a}gt das BGBM mit seinen Forschungs- und Entwicklungsprojekten zu nationalen und internationalen Biodiversit{\"a}tsprogrammen bei. Umso wichtiger ist es, der Einrichtung ein klares und modernes Auftreten zu geben. Das neue Erscheinungsbild l{\"a}sst Garten und Museum durch eine rahmende Typografie zu einer Einheit werden und kommuniziert so auch gleichzeitig das Leitbild der Einrichtung, als „Schaufenster in die Pflanzenwelt" zu dienen. Es positioniert das BGBM zum einen als wissenschaftliche Institution und zum anderen als farbenfrohes Ausflugsziel und Erholungsort.}, language = {de} } @inproceedings{WeberMarkovicDrumm2007, author = {Weber, Ingo and Markovic, Ivan and Drumm, Christian}, title = {A conceptual framework for composition in business process management}, series = {Business Information Systems : 10th International Conference, BIS 2007, Poznan, Poland, April 25-27, 2007. Proceedings}, booktitle = {Business Information Systems : 10th International Conference, BIS 2007, Poznan, Poland, April 25-27, 2007. Proceedings}, publisher = {Springer}, address = {Berlin, Heidelberg}, isbn = {978-3-540-72035-5}, doi = {10.1007/978-3-540-72035-5_5}, pages = {54 -- 66}, year = {2007}, language = {en} } @article{WeberSchulteLauterbachetal.1999, author = {Weber, Hans-Joachim and Schulte, A. and Lauterbach, Gerhard and S{\"u}dkamp, Michael [u.a.]}, title = {Studien{\"u}berblick zu transienten Druckexkursionen bei Membranoxygenatoren / A. Schulte, G. Lauterbach, M. S{\"u}dkamp, H.-J. Weber}, series = {Kardiotechnik. 8 (1999), H. 1}, journal = {Kardiotechnik. 8 (1999), H. 1}, isbn = {0941-2670}, pages = {14 -- 16}, year = {1999}, language = {de} } @article{WeberSchmittJahnetal.1989, author = {Weber, Hans-Joachim and Schmitt, W. and Jahn, D. and Euringer, H.}, title = {Ein Versuch zur theoretischen Temperaturermittlung im Schneidbereich bei Bohrungen in kortikalem Knochen - An Experiment to Calculate the Theoretical Temperature at the Drill - Cortical Bone Interface / Schmitt, W. ; Weber, H. J. ; Jahn, D. ; Euringer, H.}, series = {Biomedizinische Technik/Biomedical Engineering. 34 (1989), H. 3}, journal = {Biomedizinische Technik/Biomedical Engineering. 34 (1989), H. 3}, isbn = {0013-5585}, pages = {53 -- 56}, year = {1989}, language = {de} } @article{WeberSchmittJahn1988, author = {Weber, Hans-Joachim and Schmitt, W. and Jahn, D.}, title = {Thermische Untersuchungen beim Bohren in kortikalem Knochen unter Verwendung verschiedener K{\"u}hlsysteme / Schmitt, W. ; Weber, H. J. ; Jahn, D.}, series = {Deutsche zahn{\"a}rztliche Zeitschrift : DZZ. 43 (1988), H. 7}, journal = {Deutsche zahn{\"a}rztliche Zeitschrift : DZZ. 43 (1988), H. 7}, isbn = {0012-1029}, pages = {802 -- 805}, year = {1988}, language = {de} } @inproceedings{WeberPorschenDietzeletal.1978, author = {Weber, Hans-Joachim and Porschen, W. and Dietzel, F. and [u.a.],}, title = {In vivo analysis of the influence of combined hyperthermia and gamma irradiation on euoxic and hypoxic tumor cells}, series = {Cancer therapy by hyperthermia and radiation : [proceedings of the 2. International Symposium on Cancer Therapy by Hyperthermia and Radiation, Essen, 2.-4.6.1977]}, booktitle = {Cancer therapy by hyperthermia and radiation : [proceedings of the 2. International Symposium on Cancer Therapy by Hyperthermia and Radiation, Essen, 2.-4.6.1977]}, editor = {Streffer, Christian}, publisher = {Urban and Schwarzenberg}, address = {Baltimore ; Munich [u.a.]}, isbn = {0-8067-1701-7}, pages = {276 -- 277}, year = {1978}, language = {en} } @article{WeberMoRamakrishna2006, author = {Weber, Hans-Joachim and Mo, Xiumei and Ramakrishna, S.}, title = {PCL-PGLA composite tubular scaffold preparation and biocompatibility investigation / X. Mo, H.-J. Weber, S. Ramakrishna}, series = {The International journal of artificial organs. 29 (2006), H. 8}, journal = {The International journal of artificial organs. 29 (2006), H. 8}, publisher = {-}, pages = {790 -- 799}, year = {2006}, language = {en} }