@article{EdipSesovButenwegetal.2018,
  author    = {Edip, K. and Sesov, V. and Butenweg, Christoph and Bojadjieva, J.},
  title     = {Development of coupled numerical model for simulation of multiphase soil},
  series = {Computers and Geotechnics},
  volume    = {96},
  journal   = {Computers and Geotechnics},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {0266-352X},
  doi       = {10.1016/j.compgeo.2017.08.016},
  pages     = {118 -- 131},
  year      = {2018},
  abstract  = {In this paper, a coupled multiphase model considering both non-linearities of water retention curves and solid state modeling is proposed. The solid displacements and the pressures of both water and air phases are unknowns of the proposed model. The finite element method is used to solve the governing differential equations. The proposed method is demonstrated through simulation of seepage test and partially consolidation problem. Then, implementation of the model is done by using hypoplasticity for the solid phase and analyzing the fully saturated triaxial experiments. In integration of the constitutive law error controlling is improved and comparisons done accordingly. In this work, the advantages and limitations of the numerical model are discussed.},
  language  = {en}
}
@article{Fissabre2018,
  author    = {Fissabre, Anke},
  title     = {Die Relevanz der historischen Bauforschung f{\"u}r neue Impulse in Stadtplanung und Architektur. Das Beispiel der Chiesa della SS. Maria Incoronata und des Servitenklosters in Sabbioneta.},
  series = {archimaera},
  journal   = {archimaera},
  number    = {Nr. 7, Juli 2018},
  publisher = {Archimaera},
  address   = {Aachen},
  issn      = {1865-7001},
  url       = {http://nbn-resolving.de/urn:nbn:de:0009-21-47067},
  pages     = {99 -- 105},
  year      = {2018},
  abstract  = {Durch die Bauforschung im Rahmen des mehrj{\"a}hrigen Projektes "Die Hochkorridore von Sabbioneta" konnten der Verlauf und viele Anschl{\"u}sse der hochliegenden G{\"a}nge an bestehende Bauten weitgehend gekl{\"a}rt werden. Im Bereich der Chiesa della SS. Maria Incoronata und des angrenzenden Servitenklosters f{\"u}hrten die Bauuntersuchungen zu v{\"o}llig neuen Erkenntnissen {\"u}ber den ehemaligen Verlauf des Hochkorridors und damit zu einer Neuinterpretation des baulichen Ensembles sowie seiner Bedeutung f{\"u}r die Idealstadt. Aus dieser historischen Umdeutung entstanden Ideen f{\"u}r die Umnutzung des ehemaligen Servitenklosters und seiner angrenzenden Freifl{\"a}chen, die im Rahmen von studentischen Entw{\"u}rfen am Lehrstuhl f{\"u}r Baugeschichte und Denkmalpflege in Kooperation mit dem Lehrstuhl f{\"u}r Landschaftsarchitektur der RWTH Aachen weiterentwickelt wurden. Somit stellten sich Befunde einer historisch orientierten Bauforschung mit {\"u}bergeordneter Fragestellung als neue Impulsgeber f{\"u}r Stadtplanung, Architektur und Denkmalpflege heraus.},
  language  = {de}
}
@article{JochimMenzel2018,
  author    = {Jochim, Haldor E. and Menzel, Christoph J.},
  title     = {Die Trassenb{\"u}ndelung als Planungsmethode nachhaltiger Verkehrspolitik},
  series = {Der Eisenbahningenieur : EI},
  volume    = {69},
  journal   = {Der Eisenbahningenieur : EI},
  number    = {11},
  publisher = {DVV Media Group},
  address   = {Hamburg},
  issn      = {0013-2810},
  pages     = {26 -- 31},
  year      = {2018},
  language  = {de}
}
@article{HirschKleebergSchmitz2018,
  author    = {Hirsch, Marko and Kleeberg, Jochen and Schmitz, Philipp},
  title     = {Dynamische Asset-Allocation- Strategien im Niedrigzinsumfeld},
  series = {Absolut|report : neue Perspektiven f{\"u}r institutionelle Investoren},
  journal   = {Absolut|report : neue Perspektiven f{\"u}r institutionelle Investoren},
  number    = {6},
  publisher = {Absolut Research},
  address   = {Hamburg},
  pages     = {52},
  year      = {2018},
  language  = {de}
}
@article{Wollert2018,
  author    = {Wollert, J{\"o}rg},
  title     = {Echtzeit-Ethernet - Basis f{\"u}r Industrie 4.0},
  series = {Design \& Elektronik},
  journal   = {Design \& Elektronik},
  publisher = {WEKA-Fachmedien},
  address   = {M{\"u}nchen},
  isbn      = {0933-8667},
  year      = {2018},
  language  = {de}
}
@article{WerkhausenAlbrachtCroninetal.2018,
  author    = {Werkhausen, Amelie and Albracht, Kirsten and Cronin, Neil J and Paulsen, G{\o}ran and Bojsen-M{\o}ller, Jens and Seynnes, Olivier R},
  title     = {Effect of training-induced changes in achilles tendon stiffness on muscle-tendon behavior during landing},
  series = {Frontiers in physiology},
  journal   = {Frontiers in physiology},
  number    = {9},
  publisher = {Frontiers Research Foundation},
  address   = {Lausanne},
  issn      = {1664-042X},
  doi       = {10.3389/fphys.2018.00794},
  pages     = {11 Seiten},
  year      = {2018},
  abstract  = {During rapid deceleration of the body, tendons buffer part of the elongation of the muscle-tendon unit (MTU), enabling safe energy dissipation via eccentric muscle contraction. Yet, the influence of changes in tendon stiffness within the physiological range upon these lengthening contractions is unknown. This study aimed to examine the effect of training-induced stiffening of the Achilles tendon on triceps surae muscle-tendon behavior during a landing task. Twenty-one male subjects were assigned to either a 10-week resistance-training program consisting of single-leg isometric plantarflexion (n = 11) or to a non-training control group (n = 10). Before and after the training period, plantarflexion force, peak Achilles tendon strain and stiffness were measured during isometric contractions, using a combination of dynamometry, ultrasound and kinematics data. Additionally, testing included a step-landing task, during which joint mechanics and lengths of gastrocnemius and soleus fascicles, Achilles tendon, and MTU were determined using synchronized ultrasound, kinematics and kinetics data collection. After training, plantarflexion strength and Achilles tendon stiffness increased (15 and 18\%, respectively), and tendon strain during landing remained similar. Likewise, lengthening and negative work produced by the gastrocnemius MTU did not change detectably. However, in the training group, gastrocnemius fascicle length was offset (8\%) to a longer length at touch down and, surprisingly, fascicle lengthening and velocity were reduced by 27 and 21\%, respectively. These changes were not observed for soleus fascicles when accounting for variation in task execution between tests. These results indicate that a training-induced increase in tendon stiffness does not noticeably affect the buffering action of the tendon when the MTU is rapidly stretched. Reductions in gastrocnemius fascicle lengthening and lengthening velocity during landing occurred independently from tendon strain. Future studies are required to provide insight into the mechanisms underpinning these observations and their influence on energy dissipation.},
  language  = {en}
}
@article{BaringhausGaigall2018,
  author    = {Baringhaus, Ludwig and Gaigall, Daniel},
  title     = {Efficiency comparison of the Wilcoxon tests in paired and independent survey samples},
  series = {Metrika},
  volume    = {2018},
  journal   = {Metrika},
  number    = {81},
  publisher = {Springer},
  address   = {Berlin},
  issn      = {1435-926X},
  doi       = {10.1007/s00184-018-0661-4},
  pages     = {891 -- 930},
  year      = {2018},
  abstract  = {The efficiency concepts of Bahadur and Pitman are used to compare the Wilcoxon tests in paired and independent survey samples. A comparison through the length of corresponding confidence intervals is also done. Simple conditions characterizing the dominance of a procedure are derived. Statistical tests for checking these conditions are suggested and discussed.},
  language  = {de}
}
@article{BensbergAuthCzarnecki2018,
  author    = {Bensberg, Frank and Auth, Gunnar and Czarnecki, Christian},
  title     = {Einsatz von Text Analytics zur Unterst{\"u}tzung literaturintensiver Forschungsprozesse: Konzeption, Realisierung und Lessons Learned},
  series = {Anwendungen und Konzepte der Wirtschaftsinformatik},
  volume    = {2018},
  journal   = {Anwendungen und Konzepte der Wirtschaftsinformatik},
  number    = {8},
  publisher = {AKWI},
  address   = {Luzern},
  issn      = {2296-4592},
  doi       = {10.26034/lu.akwi.2018.3221},
  pages     = {1 -- 6},
  year      = {2018},
  abstract  = {Das anhaltende Wachstum wissenschaftlicher Ver{\"o}ffentlichungen wirft die Fragestellung auf, wie Literaturana-lysen im Rahmen von Forschungsprozessen digitalisiert und somit produktiver realisiert werden k{\"o}nnen. Insbesondere in informationstechnischen Fachgebieten ist die Forschungspraxis durch ein rasant wachsendes Publikationsaufkommen gekennzeichnet. Infolgedessen bietet sich der Einsatz von Methoden der Textanalyse (Text Analytics) an, die Textdaten automatisch vorbereiten und verarbeiten k{\"o}nnen. Erkenntnisse entstehen dabei aus Analysen von Wortarten und Subgruppen, Korrelations- sowie Zeitreihenanalysen. Dieser Beitrag stellt die Konzeption und Realisierung eines Prototypen vor, mit dem Anwender bibliographische Daten aus der etablierten Literaturdatenbank EBSCO Discovery Service mithilfe textanalytischer Methoden erschließen k{\"o}nnen. Der Prototyp basiert auf dem Analysesystem IBM Watson Explorer, das Hochschulen lizenzkostenfrei zur Verf{\"u}gung steht. Potenzielle Adressaten des Prototypen sind Forschungseinrichtungen, Beratungsunternehmen sowie Entscheidungstr{\"a}ger in Politik und Unternehmenspraxis.},
  language  = {de}
}
@article{WeldenSchejaSchoeningetal.2018,
  author    = {Welden, Rene and Scheja, Sabrina and Sch{\"o}ning, Michael Josef and Wagner, Patrick and Wagner, Torsten},
  title     = {Electrochemical Evaluation of Light-Addressable Electrodes Based on TiO2 for the Integration in Lab-on-Chip Systems},
  series = {physica status solidi a : applications and materials sciences},
  volume    = {215},
  journal   = {physica status solidi a : applications and materials sciences},
  number    = {15},
  publisher = {Wiley-VCH},
  address   = {Weinheim},
  issn      = {1862-6319},
  doi       = {10.1002/pssa.201800150},
  pages     = {Article number 1800150},
  year      = {2018},
  abstract  = {In lab-on-chip systems, electrodes are important for the manipulation (e.g., cell stimulation, electrolysis) within such systems. An alternative to commonly used electrode structures can be a light-addressable electrode. Here, due to the photoelectric effect, the conducting area can be adjusted by modification of the illumination area which enables a flexible control of the electrode. In this work, titanium dioxide based light-addressable electrodes are fabricated by a sol-gel technique and a spin-coating process, to deposit a thin film on a fluorine-doped tin oxide glass. To characterize the fabricated electrodes, the thickness, and morphological structure are measured by a profilometer and a scanning electron microscope. For the electrochemical behavior, the dark current and the photocurrent are determined for various film thicknesses. For the spatial resolution behavior, the dependency of the photocurrent while changing the area of the illuminated area is studied. Furthermore, the addressing of single fluid compartments in a three-chamber system, which is added to the electrode, is demonstrated.},
  language  = {en}
}
@article{MuellerBeckersMussmannetal.2018,
  author    = {M{\"u}ller, Janina and Beckers, Mario and Mußmann, Nina and Bongaerts, Johannes and B{\"u}chs, Jochen},
  title     = {Elucidation of auxotrophic deficiencies of Bacillus pumilus DSM 18097 to develop a defined minimal medium},
  series = {Microbial Cell Factories},
  volume    = {17},
  journal   = {Microbial Cell Factories},
  number    = {1},
  publisher = {BioMed Central},
  issn      = {1475-2859},
  doi       = {10.1186/s12934-018-0956-1},
  pages     = {Article No. 106},
  year      = {2018},
  abstract  = {Background Culture media containing complex compounds like yeast extract or peptone show numerous disadvantages. The chemical composition of the complex compounds is prone to significant variations from batch to batch and quality control is difficult. Therefore, the use of chemically defined media receives more and more attention in commercial fermentations. This concept results in better reproducibility, it simplifies downstream processing of secreted products and enable rapid scale-up. Culturing bacteria with unknown auxotrophies in chemically defined media is challenging and often not possible without an extensive trial-and-error approach. In this study, a respiration activity monitoring system for shake flasks and its recent version for microtiter plates were used to clarify unknown auxotrophic deficiencies in the model organism Bacillus pumilus DSM 18097. Results Bacillus pumilus DSM 18097 was unable to grow in a mineral medium without the addition of complex compounds. Therefore, a rich chemically defined minimal medium was tested containing basically all vitamins, amino acids and nucleobases, which are essential ingredients of complex components. The strain was successfully cultivated in this medium. By monitoring of the respiration activity, nutrients were supplemented to and omitted from the rich chemically defined medium in a rational way, thus enabling a systematic and fast determination of the auxotrophic deficiencies. Experiments have shown that the investigated strain requires amino acids, especially cysteine or histidine and the vitamin biotin for growth. Conclusions The introduced method allows an efficient and rapid identification of unknown auxotrophic deficiencies and can be used to develop a simple chemically defined tailor-made medium. B. pumilus DSM 18097 was chosen as a model organism to demonstrate the method. However, the method is generally suitable for a wide range of microorganisms. By combining a systematic combinatorial approach based on monitoring the respiration activity with cultivation in microtiter plates, high throughput experiments with high information content can be conducted. This approach facilitates media development, strain characterization and cultivation of fastidious microorganisms in chemically defined minimal media while simultaneously reducing the experimental effort.},
  language  = {en}
}
@article{ValeroBungCrookston2018,
  author    = {Valero, Daniel and Bung, Daniel Bernhard and Crookston, B.M.},
  title     = {Energy dissipation of a Type III basin under design and adverse conditions for stepped and smooth spillways},
  series = {Journal of Hydraulic Engineering},
  volume    = {144},
  journal   = {Journal of Hydraulic Engineering},
  number    = {7},
  publisher = {ASCE},
  address   = {Reston, Va.},
  issn      = {0733-9429},
  doi       = {10.1061/(ASCE)HY.1943-7900.0001482},
  year      = {2018},
  abstract  = {New information regarding the influence of a stepped chute on the hydraulic performance of the United States Bureau of Reclamation (Reclamation) Type III hydraulic jump stilling basin is presented for design (steady) and adverse (decreasing tailwater) conditions. Using published experimental data and computational fluid dynamics (CFD) models, this paper presents a detailed comparison between smooth-chute and stepped-chute configurations for chute slopes of 0.8H:1V and 4H:1V and Froude numbers (F) ranging from 3.1 to 9.5 for a Type III basin designed for F = 8. For both stepped and smooth chutes, the relative role of each basin element was quantified, up to the most hydraulic extreme case of jump sweep-out. It was found that, relative to a smooth chute, the turbulence generated by a stepped chute causes a higher maximum velocity decay within the stilling basin, which represents an enhancement of the Type III basin's performance but also a change in the relative role of the basin elements. Results provide insight into the ability of the CFD models [unsteady Reynolds-averaged Navier-Stokes (RANS) equations with renormalization group (RNG) k-ϵ turbulence model and volume-of-fluid (VOF) for free surface tracking] to predict the transient basin flow structure and velocity profiles. Type III basins can perform adequately with a stepped chute despite the effects steps have on the relative role of each basin element. It is concluded that the classic Type III basin design, based upon methodology by reclamation specific to smooth chutes, can be hydraulically improved for the case of stepped chutes for design and adverse flow conditions using the information presented herein.},
  language  = {en}
}
@article{TekinAshikagaHorikawaetal.2018,
  author    = {Tekin, Nurettin and Ashikaga, Mitsugu and Horikawa, Atsushi and Funke, Harald},
  title     = {Enhancement of fuel flexibility of industrial gas turbines by development of innovative hydrogen combustion systems},
  series = {Gas for energy},
  journal   = {Gas for energy},
  number    = {2},
  publisher = {Vulkan-Verlag},
  address   = {Essen},
  pages     = {4},
  year      = {2018},
  abstract  = {For fuel flexibility enhancement hydrogen represents a possible alternative gas turbine fuel within future low emission power generation, in case of hydrogen production by the use of renewable energy sources such as wind energy or biomass. Kawasaki Heavy Industries, Ltd. (KHI) has research and development projects for future hydrogen society; production of hydrogen gas, refinement and liquefaction for transportation and storage, and utilization with gas turbine / gas engine for the generation of electricity. In the development of hydrogen gas turbines, a key technology is the stable and low NOx hydrogen combustion, especially Dry Low Emission (DLE) or Dry Low NOx (DLN) hydrogen combustion. Due to the large difference in the physical properties of hydrogen compared to other fuels such as natural gas, well established gas turbine combustion systems cannot be directly applied for DLE hydrogen combustion. Thus, the development of DLE hydrogen combustion technologies is an essential and challenging task for the future of hydrogen fueled gas turbines. The DLE Micro-Mix combustion principle for hydrogen fuel has been in development for many years to significantly reduce NOx emissions. This combustion principle is based on cross-flow mixing of air and gaseous hydrogen which reacts in multiple miniaturized "diffusion-type" flames. The major advantages of this combustion principle are the inherent safety against flashback and the low NOx-emissions due to a very short residence time of the reactants in the flame region of the micro-flames.},
  language  = {en}
}
@article{ButenwegMarinkovic2018,
  author    = {Butenweg, Christoph and Marinkovic, Marko},
  title     = {Erdbebensicherer Anschluss von Ausfachungsmauerwerk in Stahlbetonrahmentragwerken mit Entkopplungselementen},
  series = {Bauingenieur},
  volume    = {93},
  journal   = {Bauingenieur},
  number    = {9},
  publisher = {VDI Fachmedien},
  address   = {D{\"u}sseldorf},
  issn      = {0005-6650},
  pages     = {333 -- 341},
  year      = {2018},
  abstract  = {Stahlbetonrahmentragwerke mit Mauerwerksausfachungen weisen nach Erdbebenereignissen h{\"a}ufig schwere Sch{\"a}den auf, da die Ausfachungen ohne weitere konstruktive Maßnahmen mit vollem Kontakt zum Stahlbetonrahmen eingemauert werden. Durch die unplanm{\"a}ßige Beteiligung am horizontalen Lastabtrag erfahren die Ausfachungen Belastungen in Wandebene und beeinflussen das globale Schwingungsverhalten der Rahmentragwerke. In Kombination mit den gleichzeitig auftretenden seismischen Tr{\"a}gheitskr{\"a}ften senkrecht zur Wand f{\"u}hrt dies in vielen F{\"a}llen zu einem Versagen der mit niedrigen Festigkeiten ausgef{\"u}hrten Ausfachungen. Dies war der Anlass in dem europ{\"a}ischen Forschungsprojekt INSYSME ein Entkopplungssystem zu entwickeln, mit dem Rahmen und Ausfachung durch ein spezielles Profil aus Elastomeren entkoppelt werden. Das Profil erm{\"o}glicht Relativverschiebungen zwischen Rahmen und Ausfachung und stellt gleichzeitig die Aufnahme von Belastungen senkrecht zur Wand sicher. Der Beitrag erl{\"a}utert zun{\"a}chst den Aufbau des Systems und gibt einen {\"U}berblick {\"u}ber die in Kleinbauteilversuchen ermittelten Tragf{\"a}higkeiten. Zudem werden experimentelle Untersuchungen an mit hochw{\"a}rmed{\"a}mmenden Mauerziegeln ausgefachten Stahlbetonrahmen mit und ohne Entkopplungssystem f{\"u}r getrennte und kombinierte Belastungen in und senkrecht zur Wandebene vorgestellt. Auf Grundlage einer Versuchsauswertung und eines Ergebnisvergleichs werden Wirkungsweise und Effektivit{\"a}t des entwickelten Entkopplungssystems demonstriert.},
  language  = {de}
}
@article{SchifferFerrein2018,
  author    = {Schiffer, Stefan and Ferrein, Alexander},
  title     = {ERIKA—Early Robotics Introduction at Kindergarten Age},
  series = {Multimodal Technologies Interact},
  volume    = {2},
  journal   = {Multimodal Technologies Interact},
  number    = {4},
  publisher = {MDPI},
  address   = {Basel},
  issn      = {2414-4088},
  doi       = {10.3390/mti2040064},
  pages     = {15},
  year      = {2018},
  abstract  = {In this work, we report on our attempt to design and implement an early introduction to basic robotics principles for children at kindergarten age. One of the main challenges of this effort is to explain complex robotics contents in a way that pre-school children could follow the basic principles and ideas using examples from their world of experience. What sets apart our effort from other work is that part of the lecturing is actually done by a robot itself and that a quiz at the end of the lesson is done using robots as well. The humanoid robot Pepper from Softbank, which is a great platform for human-robot interaction experiments, was used to present a lecture on robotics by reading out the contents to the children making use of its speech synthesis capability. A quiz in a Runaround-game-show style after the lecture activated the children to recap the contents they acquired about how mobile robots work in principle. In this quiz, two LEGO Mindstorm EV3 robots were used to implement a strongly interactive scenario. Besides the thrill of being exposed to a mobile robot that would also react to the children, they were very excited and at the same time very concentrated. We got very positive feedback from the children as well as from their educators. To the best of our knowledge, this is one of only few attempts to use a robot like Pepper not as a tele-teaching tool, but as the teacher itself in order to engage pre-school children with complex robotics contents.},
  language  = {en}
}
@article{HeinkeKnickerAlbracht2018,
  author    = {Heinke, Lars N. and Knicker, Axel J. and Albracht, Kirsten},
  title     = {Evaluation of passively induced shoulder stretch reflex using an isokinetic dynamometer in male overhead athletes},
  series = {Isokinetics and Exercise Science},
  volume    = {26},
  journal   = {Isokinetics and Exercise Science},
  number    = {4},
  publisher = {IOS Press},
  address   = {Amsterdam},
  issn      = {1878-5913},
  doi       = {10.3233/IES-184111},
  pages     = {265 -- 274},
  year      = {2018},
  abstract  = {BACKGROUND: Muscle stretch reflexes are widely considered to beneficially influence joint stability and power generation in the lower limbs. While in the upper limbs and especially in the muscles surrounding the shoulder joint such evidence is lacking. OBJECTIVE: To quantify the electromyographical response in the muscles crossing the shoulder of specifically trained overhead athletes to an anterior perturbation force. METHODS: Twenty healthy male participants performed six sets of different external shoulder rotation stretches on an isokinetic dynamometer over a range of amplitudes and muscle pre-activation moment levels. All stretches were applied with a dynamometer acceleration of 10,000∘/s2 and a velocity of 150∘/s. Electromyographical response was measured via sEMG. RESULTS: Consistent reflexes were not observed in all experimental conditions. The reflex latencies revealed a significant muscle main effect (F (2,228) = 99.31, p< 0.001; η2= 0.466; f= 0.934) and a pre-activation main effect (F (1,228) = 142.21, p< 0.001; η2= 0.384; f= 1.418). The stretch reflex amplitude yielded a significant pre-activation main effect (F (1,222) = 470.373, p< 0.001; η2= 0.679; f= 1.454). CONCLUSION: Short latency muscle reflexes showed a tendency to an anterior to posterior muscle recruitment whereby the main internal rotator muscles of the shoulder revealed the most consistent results.},
  language  = {en}
}
@article{EckertRudolphGuoetal.2018,
  author    = {Eckert, Alexander and Rudolph, Tobias and Guo, Jiaqi and Mang, Thomas and Walther, Andreas},
  title     = {Exceptionally Ductile and Tough Biomimetic Artificial Nacre with Gas Barrier Function},
  series = {Advanced Materials},
  volume    = {30},
  journal   = {Advanced Materials},
  number    = {32},
  publisher = {Wiley-VCH},
  doi       = {10.1002/adma.201802477},
  pages     = {Article number 1802477},
  year      = {2018},
  abstract  = {Synthetic mimics of natural high-performance structural materials have shown great and partly unforeseen opportunities for the design of multifunctional materials. For nacre-mimetic nanocomposites, it has remained extraordinarily challenging to make ductile materials with high stretchability at high fractions of reinforcements, which is however of crucial importance for flexible barrier materials. Here, highly ductile and tough nacre-mimetic nanocomposites are presented, by implementing weak, but many hydrogen bonds in a ternary nacre-mimetic system consisting of two polymers (poly(vinyl amine) and poly(vinyl alcohol)) and natural nanoclay (montmorillonite) to provide efficient energy dissipation and slippage at high nanoclay content (50 wt\%). Tailored interactions enable exceptional combinations of ductility (close to 50\% strain) and toughness (up to 27.5 MJ m⁻³). Extensive stress whitening, a clear sign of high internal dynamics at high internal cohesion, can be observed during mechanical deformation, and the materials can be folded like paper into origami planes without fracture. Overall, the new levels of ductility and toughness are unprecedented in highly reinforced bioinspired nanocomposites and are of critical importance to future applications, e.g., as barrier materials needed for encapsulation and as a printing substrate for flexible organic electronics.},
  language  = {en}
}
@article{JildehOberlaenderKirchneretal.2018,
  author    = {Jildeh, Zaid B. and Oberl{\"a}nder, Jan and Kirchner, Patrick and Keusgen, Michael and Wagner, Patrick H. and Sch{\"o}ning, Michael Josef},
  title     = {Experimental and Numerical Analyzes of a Sensor Based on Interdigitated Electrodes for Studying Microbiological Alterations},
  series = {physica status solidi (a): applications and materials science},
  volume    = {215},
  journal   = {physica status solidi (a): applications and materials science},
  number    = {15},
  publisher = {Wiley-VCH},
  address   = {Weinheim},
  issn      = {1862-6319},
  doi       = {10.1002/pssa.201700920},
  pages     = {Artikel 1700920},
  year      = {2018},
  abstract  = {In this work, a cell-based biosensor to evaluate the sterilization efficacy of hydrogen peroxide vapor sterilization processes is characterized. The transducer of the biosensor is based on interdigitated gold electrodes fabricated on an inert glass substrate. Impedance spectroscopy is applied to evaluate the sensor behavior and the alteration of test microorganisms due to the sterilization process. These alterations are related to changes in relative permittivity and electrical conductivity of the bacterial spores. Sensor measurements are conducted with and without bacterial spores (Bacillus atrophaeus), as well as after an industrial sterilization protocol. Equivalent two-dimensional numerical models based on finite element method of the periodic finger structures of the interdigitated gold electrodes are designed and validated using COMSOL® Multiphysics software by the application of known dielectric properties. The validated models are used to compute the electrical properties at different sensor states (blank, loaded with spores, and after sterilization). As a final result, we will derive and tabulate the frequency-dependent electrical parameters of the spore layer using a novel model that combines experimental data with numerical optimization techniques.},
  language  = {en}
}
@article{BirklDiendorferKernetal.2018,
  author    = {Birkl, Josef and Diendorfer, Gerhard and Kern, Alexander and Thern, Stephan},
  title     = {Extrem hohe Blitzstr{\"o}me},
  series = {Elektropraktiker},
  volume    = {72},
  journal   = {Elektropraktiker},
  number    = {3},
  publisher = {Huss Medien},
  address   = {Berlin},
  pages     = {217 -- 225},
  year      = {2018},
  abstract  = {Blitze sind nach wie vor eine enorme Schadensquelle f{\"u}r Personensch{\"a}den, Br{\"a}nde, mechanische Zerst{\"o}rungen und insbesondere auch {\"U}berspannungen. Das zeigen nicht zuletzt aktuelle Statistiken der Schadensversicherer. Immer wieder gibt es Meldungen {\"u}ber extrem hohe Blitzstr{\"o}me, die nat{\"u}rlich auch zu großen Sch{\"a}den und Zerst{\"o}rungen f{\"u}hren k{\"o}nnen. Dabei werden Scheitelwerte von teilweise deutlich {\"u}ber 300 kA genannt. Dies wirft Fragen auf, da die „klassische" Blitzstatistik (z. B. nach CIGRE und IEC [8][10]) bisher solche Werte nicht kennt. Diese extremen Blitzstr{\"o}me werden meist aus den Daten von Blitzortungssystemen ermittelt.},
  language  = {de}
}
@article{LapitanRogatkinPersheyevetal.2018,
  author    = {Lapitan, Denis G. and Rogatkin, Dmitrii A. and Persheyev, Sydulla K. and Kotliar, Konstantin},
  title     = {False spectra formation in the differential two-channel scheme of the laser Doppler flowmeter},
  series = {Biomedizinische Technik},
  volume    = {63},
  journal   = {Biomedizinische Technik},
  number    = {4},
  publisher = {De Gruyter},
  address   = {Berlin},
  issn      = {0013-5585},
  doi       = {10.1515/bmt-2017-0060},
  pages     = {439 -- 444},
  year      = {2018},
  abstract  = {Noise in the differential two-channel scheme of a classic laser Doppler flowmetry (LDF) instrument was studied. Formation of false spectral components in the output signal due to beating of electrical signals in the differential amplifier was found out. The improved block-diagram of the flowmeter was developed allowing to reduce the noise.},
  language  = {en}
}
@article{PoghossianJablonskiKochetal.2018,
  author    = {Poghossian, Arshak and Jablonski, Melanie and Koch, Claudia and Bronder, Thomas and Rolka, David and Wege, Christina and Sch{\"o}ning, Michael Josef},
  title     = {Field-effect biosensor using virus particles as scaffolds for enzyme immobilization},
  series = {Biosensors and Bioelectronics},
  volume    = {110},
  journal   = {Biosensors and Bioelectronics},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {0956-5663},
  doi       = {10.1016/j.bios.2018.03.036},
  pages     = {168 -- 174},
  year      = {2018},
  abstract  = {A field-effect biosensor employing tobacco mosaic virus (TMV) particles as scaffolds for enzyme immobilization is presented. Nanotubular TMV scaffolds allow a dense immobilization of precisely positioned enzymes with retained activity. To demonstrate feasibility of this new strategy, a penicillin sensor has been developed by coupling a penicillinase with virus particles as a model system. The developed field-effect penicillin biosensor consists of an Al-p-Si-SiO₂-Ta₂O₅-TMV structure and has been electrochemically characterized in buffer solutions containing different concentrations of penicillin G. In addition, the morphology of the biosensor surface with virus particles was characterized by scanning electron microscopy and atomic force microscopy methods. The sensors possessed a high penicillin sensitivity of ~ 92 mV/dec in a nearly-linear range from 0.1 mM to 10 mM, and a low detection limit of about 50 µM. The long-term stability of the penicillin biosensor was periodically tested over a time period of about one year without any significant loss of sensitivity. The biosensor has also been successfully applied for penicillin detection in bovine milk samples.},
  language  = {en}
}
@article{VahidpourOberlaenderSchoening2018,
  author    = {Vahidpour, Farnoosh and Oberl{\"a}nder, Jan and Sch{\"o}ning, Michael Josef},
  title     = {Flexible Calorimetric Gas Sensors for Detection of a Broad Concentration Range of Gaseous Hydrogen Peroxide: A Step Forward to Online Monitoring of Food-Package Sterilization Processes},
  series = {Phys. Status Solidi A},
  volume    = {215},
  journal   = {Phys. Status Solidi A},
  number    = {15},
  publisher = {Wiley-VCH},
  address   = {Weinheim},
  doi       = {10.1002/pssa.201800044},
  pages     = {Artikel 1800044},
  year      = {2018},
  abstract  = {In this study, flexible calorimetric gas sensors are developed for specificdetection of gaseous hydrogen peroxide (H₂O₂) over a wide concentrationrange, which is used in sterilization processes for aseptic packaging industry.The flexibility of these sensors is an advantage for identifying the chemical components of the sterilant on the corners of the food boxes, so-called "coldspots", as critical locations in aseptic packaging, which are of great importance. These sensors are fabricated on flexible polyimide films by means of thin-film technique. Thin layers of titanium and platinum have been deposited on polyimide to define the conductive structures of the sensors. To detect the high-temperature evaporated H₂O₂, a differential temperature set-up is proposed. The sensors are evaluated in a laboratory-scaled sterilizationsystem to simulate the sterilization process. The concentration range of the evaporated H₂O₂ from 0 to 7.7\% v/v was defined and the sensors have successfully detected high as well as low H₂O₂ concentrations with a sensitivity of 5.04 °C/\% v/v. The characterizations of the sensors confirm their precise fabrication, high sensitivity and the novelty of low H₂O₂ concentration detections for future inline monitoring of food-package sterilization.},
  language  = {en}
}
@article{Golland2018,
  author    = {Golland, Alexander},
  title     = {Gemeinsame Verantwortlichkeit in mehrstufigen Verarbeitungsszenarien},
  volume    = {21},
  number    = {7-8},
  publisher = {dfv Mediengruppe},
  address   = {Frankfurt a.M.},
  issn      = {1434-6354},
  pages     = {433 -- 438},
  year      = {2018},
  abstract  = {Die Rechtsfigur der gemeinsamen Verantwortlichkeit besch{\"a}ftigt die datenschutzrechtliche Literatur seit Langem. Die Bestimmung der Verantwortlichkeit bei arbeitsteiligen Verarbeitungsverfahren, welche vor allem bei heutigen Plattformdiensten {\"u}blich sind, ist komplex: Stets sind mehrere Akteure beteiligt und in der Regel werden durch die Handlung eines Beteiligten mehrere Verarbeitungsschritte ausgel{\"o}st. Nun hat sich der EuGH in einem in mehrfacher Hinsicht bemerkenswerten Urteil ge{\"a}ußert.},
  language  = {de}
}
@article{KoenigWolf2018,
  author    = {K{\"o}nig, Johannes Alexander and Wolf, Martin},
  title     = {GHOST: An Evaluated Competence Developing Game for Cybersecurity Awareness Training},
  series = {International Journal on Advances in Security},
  volume    = {11},
  journal   = {International Journal on Advances in Security},
  number    = {3 \& 4},
  publisher = {IARIA Journals},
  issn      = {1942-2636},
  pages     = {274 -- 287},
  year      = {2018},
  abstract  = {To train end users how to interact with digital systems is indispensable to ensure a strong computer security. 'Competence Developing Game'-based approaches are particularly suitable for this purpose because of their motivation-and simulation-aspects. In this paper the Competence Developing Game 'GHOST' for cybersecurity awareness trainings and its underlying patterns are described. Accordingly, requirements for an 'Competence Developing Game' based training are discussed. Based on these requirements it is shown how a game can fulfill these requirements. A supplementary game interaction design and a corresponding evaluation study is shown. The combination of training requirements and interaction design is used to create a 'Competence Developing Game'-based training concept. A part of these concept is implemented into a playable prototype that serves around one hour of play respectively training time. This prototype is used to perform an evaluation of the game and training aspects of the awareness training. Thereby, the quality of the game aspect and the effectiveness of the training aspect are shown.},
  language  = {en}
}
@article{SchmidtEnningPfaff2018,
  author    = {Schmidt, Bernd and Enning, Manfred and Pfaff, Raphael},
  title     = {G{\"u}terwagen 4.0 - Der G{\"u}terwagen f{\"u}r das Internet der Dinge Teil 3: Einf{\"u}hrungsszenarien f{\"u}r aktive, kommunikative G{\"u}terwagen},
  series = {ETR - Eisenbahntechnische Rundschau},
  volume    = {67},
  journal   = {ETR - Eisenbahntechnische Rundschau},
  number    = {5},
  publisher = {DVV Media Group},
  address   = {Hamburg},
  issn      = {0013-2845},
  pages     = {60 -- 64},
  year      = {2018},
  abstract  = {Wenn durch innovative, automatisierte G{\"u}terwagen betriebswirtschaftliche Vorteile nutzbar gemacht werden sollen, muss die Migration auf das neue System in sinnvollen Teilschritten unter Ber{\"u}cksichtigung der organisationellen und betrieblichen Vereinbarkeit vorgenommen werden. Eine stufenweise Migration mit Nachr{\"u}stbarkeit und Kompatibilit{\"a}t kann die optimale Ausstattungsvariante f{\"u}r die unterschiedlichen Betriebsszenarien sowie eine Steigerung der Wirtschaftlichkeit des Gesamtsystems bieten.},
  language  = {de}
}
@article{FingerBraunBil2018,
  author    = {Finger, Felix and Braun, Carsten and Bil, Cees},
  title     = {Impact of electric propulsion technology and mission requirements on the performance of VTOL UAVs},
  series = {CEAS Aeronautical Journal},
  volume    = {10},
  journal   = {CEAS Aeronautical Journal},
  number    = {3},
  publisher = {Springer},
  issn      = {1869-5582 print},
  doi       = {10.1007/s13272-018-0352-x},
  pages     = {843},
  year      = {2018},
  abstract  = {One of the engineering challenges in aviation is the design of transitioning vertical take-off and landing (VTOL) aircraft. Thrust-borne flight implies a higher mass fraction of the propulsion system, as well as much increased energy consumption in the take-off and landing phases. This mass increase is typically higher for aircraft with a separate lift propulsion system than for aircraft that use the cruise propulsion system to support a dedicated lift system. However, for a cost-benefit trade study, it is necessary to quantify the impact the VTOL requirement and propulsion configuration has on aircraft mass and size. For this reason, sizing studies are conducted. This paper explores the impact of considering a supplemental electric propulsion system for achieving hovering flight. Key variables in this study, apart from the lift system configuration, are the rotor disk loading and hover flight time, as well as the electrical systems technology level for both batteries and motors. Payload and endurance are typically used as the measures of merit for unmanned aircraft that carry electro-optical sensors, and therefore the analysis focuses on these particular parameters.},
  language  = {en}
}
@article{MiyamotoSekiSutoetal.2018,
  author    = {Miyamoto, Koichiro and Seki, Kosuke and Suto, Takeyuki and Werner, Frederik and Wagner, Torsten and Sch{\"o}ning, Michael Josef and Yoshinobu, Tatsuo},
  title     = {Improved spatial resolution of the chemical imaging sensor with a hybrid illumination that suppresses lateral diffusion of photocarriers},
  series = {Sensor and Actuators B: Chemical},
  volume    = {273},
  journal   = {Sensor and Actuators B: Chemical},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {0925-4005},
  doi       = {10.1016/j.snb.2018.07.016},
  pages     = {1328 -- 1333},
  year      = {2018},
  abstract  = {The chemical imaging sensor is a semiconductor-based chemical sensor capable of visualizing pH and ion distributions. The spatial resolution depends on the lateral diffusion of photocarriers generated by illumination of the semiconductor substrate. In this study, two types of optical setups, one based on a bundle of optical fibers and the other based on a binocular tube head, were developed to project a hybrid illumination of a modulated light beam and a ring-shaped constant illumination onto the sensor plate. An improved spatial resolution was realized by the ring-shaped constant illumination, which suppressed lateral diffusion of photocarriers by enhanced recombination due to the increased carrier concentration.},
  language  = {en}
}
@article{TeumerCapitainRossJonesetal.2018,
  author    = {Teumer, T. and Capitain, C. and Ross-Jones, J. and Tippk{\"o}tter, Nils and R{\"a}dle, M. and Methner, F.-J.},
  title     = {In-line Haze Monitoring Using a Spectrally Resolved Back Scattering Sensor},
  series = {BrewingScience},
  volume    = {71},
  journal   = {BrewingScience},
  number    = {5/6},
  publisher = {Fachverlag Hans Carl},
  address   = {N{\"u}rnberg},
  issn      = {1613-2041},
  pages     = {49 -- 55},
  year      = {2018},
  abstract  = {In the present work an optical sensor in combination with a spectrally resolved detection device for in-line particle-size-monitoring for quality control in beer production is presented. The principle relies on the size and wavelength dependent backscatter of growing particles in fluids. Measured interference structures of backscattered light are compared with calculated theoretical values, based on Mie-Theory, and fitted with a linear least square method to obtain particle size distributions. For this purpose, a broadband light source in combination with a process-CCD-spectrometer (charge ? coupled device spectrometer) and process adapted fiber optics are used. The goal is the development of an easy and flexible measurement device for in-line-monitoring of particle size. The presented device can be directly installed in product fill tubes or vessels, follows CIP- (cleaning in place) and removes the need of sample taking. A proof of concept and preliminary results, measuring protein precipitation, are presented.},
  language  = {en}
}
@article{EngelHoltmannUlberetal.2018,
  author    = {Engel, Mareike and Holtmann, Dirk and Ulber, Roland and Tippk{\"o}tter, Nils},
  title     = {Increased Biobutanol Production by Mediator-Less Electro-Fermentation},
  series = {Biotechnology Journal},
  volume    = {14},
  journal   = {Biotechnology Journal},
  number    = {4},
  publisher = {Wiley-VCH},
  address   = {Weinheim},
  issn      = {1860-7314},
  doi       = {10.1002/biot.201800514},
  year      = {2018},
  abstract  = {A future bio-economy should not only be based on renewable raw materials but also in the raise of carbon yields of existing production routes. Microbial electrochemical technologies are gaining increased attention for this purpose. In this study, the electro-fermentative production of biobutanol with C. acetobutylicum without the use of exogenous mediators is investigated regarding the medium composition and the reactor design. It is shown that the use of an optimized synthetic culture medium allows higher product concentrations, increased biofilm formation, and higher conductivities compared to a synthetic medium supplemented with yeast extract. Moreover, the optimization of the reactor system results in a doubling of the maximum product concentrations for fermentation products. When a working electrode is polarized at -600 mV vs. Ag/AgCl, a shift from butyrate to acetone and butanol production is induced. This leads to an increased final solvent yield of Yᴀᴃᴇ = 0.202 gg⁻¹ (control 0.103 gg⁻¹), which is also reflected in a higher carbon efficiency of 37.6\% compared to 23.3\% (control) as well as a fourfold decrease in simplified E-factor to 0.43. The results are promising for further development of biobutanol production in bioelectrochemical systems in order to fulfil the principles of Green Chemistry.},
  language  = {en}
}
@article{LauraDrechslerErdtetal.2018,
  author    = {Laura, C.O. and Drechsler, Klaus and Erdt, M. and Wesarg, S. and Bale, R.},
  title     = {Intervention assessment tool for primary tumors in the liver},
  series = {Current Directions in Biomedical Engineering},
  volume    = {4},
  journal   = {Current Directions in Biomedical Engineering},
  number    = {1},
  publisher = {De Gruyter},
  address   = {Berlin},
  issn      = {2364-5504},
  doi       = {10.1515/cdbme-2018-0081},
  pages     = {337 -- 340},
  year      = {2018},
  abstract  = {After a liver tumor intervention the medical doctor has to compare both pre and postoperative CT acquisitions to ensure that all carcinogenic cells are destroyed. A correct assessment of the intervention is of vital importance, since it will reduce the probability of tumor recurrence. Some methods have been proposed to support the medical doctors during the assessment process, however, all of them focus on secondary tumors. In this paper a tool is presented that enables the outcome validation for both primary and secondary tumors. Therefore, a multiphase registration (preoperative arterial and portal phases) followed by a registration between the pre and postoperative CT images is carried out. The first registration is in charge of the primary tumors that are only visible in the arterial phase. The secondary tumors will be incorporated in the second registration step. Finally, the part of the tumor that was not covered by the necrosis is quantified and visualized. The method has been tested in 9 patients, with an average registration error of 1.41 mm.},
  language  = {en}
}
@article{RosinButenwegCacciatoreetal.2018,
  author    = {Rosin, Julia and Butenweg, Christoph and Cacciatore, Pamela and Boesen, Niklas},
  title     = {Investigation of the seismic performance of modern masonry buildings during the Emilia Romagna earthquake series},
  series = {Mauerwerk},
  volume    = {22},
  journal   = {Mauerwerk},
  number    = {4},
  publisher = {Ernst \& Sohn},
  address   = {Berlin},
  issn      = {1437-1022},
  doi       = {10.1002/dama.201800013},
  pages     = {238 -- 250},
  year      = {2018},
  abstract  = {The article presents the investigation of the seismic behaviour of a modern URM building located in the municipality of Finale Emilia in province of Modena, Northern Italy. The building is situated in the centre of the series of the 2012 Northern Italy earthquakes and has not suffered any damage during the earthquake series in 2012. The observed earthquake resistance of the building is compared with predicted resistances based on linear and nonlinear design approaches according to Eurocode. Furthermore, probabilistic analyses based on nonlinear calculation models taking into account scattering of the most relevant input parameters are carried out to identify their influence to the results and to derive fragility curves.},
  language  = {en}
}
@article{QuittmannMeskemperAbeletal.2018,
  author    = {Quittmann, Oliver J. and Meskemper, Joshua and Abel, Thomas and Albracht, Kirsten and Foitschik, Tina and Rojas-Vega, Sandra and Str{\"u}der, Heiko K.},
  title     = {Kinematics and kinetics of handcycling propulsion at increasing workloads in able-bodied subjects},
  series = {Sports Engineereing},
  volume    = {21},
  journal   = {Sports Engineereing},
  number    = {21},
  publisher = {Springer Nature},
  address   = {Cham},
  issn      = {1460-2687},
  doi       = {10.1007/s12283-018-0269-y},
  pages     = {283 -- 294},
  year      = {2018},
  abstract  = {In Paralympic sports, biomechanical optimisation of movements and equipment seems to be promising for improving performance. In handcycling, information about the biomechanics of this sport is mainly provided by case studies. The aim of the current study was (1) to examine changes in handcycling propulsion kinematics and kinetics due to increasing workloads and (2) identify parameters that are associated with peak aerobic performance. Twelve non-disabled male competitive triathletes without handcycling experience voluntarily participated in the study. They performed an initial familiarisation protocol and incremental step test until exhaustion in a recumbent racing handcycle that was attached to an ergometer. During the incremental test, tangential crank kinetics, 3D joint kinematics, blood lactate and ratings of perceived exertion (local and global) were identified. As a performance criterion, the maximal power output during the step test (Pmax) was calculated and correlated with biomechanical parameters. For higher workloads, an increase in crank torque was observed that was even more pronounced in the pull phase than in the push phase. Furthermore, participants showed an increase in shoulder internal rotation and abduction and a decrease in elbow flexion and retroversion. These changes were negatively correlated with performance. At high workloads, it seems that power output is more limited by the transition from pull to push phase than at low workloads. It is suggested that successful athletes demonstrate small alterations of their kinematic profile due to increasing workloads. Future studies should replicate and expand the test spectrum (sprint and continuous loads) as well as use methods like surface electromyography (sEMG) with elite handcyclists.},
  language  = {de}
}
@article{SvaneborgKarimiVarzanehHojdisetal.2018,
  author    = {Svaneborg, Carsten and Karimi-Varzaneh, Hossein Ali and Hojdis, Nils and Fleck, Franz and Everaers, Ralf},
  title     = {Kremer-Grest Models for Universal Properties of Specific Common Polymer Species},
  series = {Soft Condensed Matter},
  journal   = {Soft Condensed Matter},
  number    = {1606.05008},
  year      = {2018},
  abstract  = {The Kremer-Grest (KG) bead-spring model is a near standard in Molecular Dynamic simulations of generic polymer properties. It owes its popularity to its computational efficiency, rather than its ability to represent specific polymer species and conditions. Here we investigate how to adapt the model to match the universal properties of a wide range of chemical polymers species. For this purpose we vary a single parameter originally introduced by Faller and M{\"u}ller-Plathe, the chain stiffness. Examples include polystyrene, polyethylene, polypropylene, cis-polyisoprene, polydimethylsiloxane, polyethyleneoxide and styrene-butadiene rubber. We do this by matching the number of Kuhn segments per chain and the number of Kuhn segments per cubic Kuhn volume for the polymer species and for the Kremer-Grest model. We also derive mapping relations for converting KG model units back to physical units, in particular we obtain the entanglement time for the KG model as function of stiffness allowing for a time mapping. To test these relations, we generate large equilibrated well entangled polymer melts, and measure the entanglement moduli using a static primitive-path analysis of the entangled melt structure as well as by simulations of step-strain deformation of the model melts. The obtained moduli for our model polymer melts are in good agreement with the experimentally expected moduli.},
  language  = {en}
}
@article{ZieburaBremenSchleifenbaumetal.2018,
  author    = {Ziebura, Dawid and Bremen, Sebastian and Schleifenbaum, Johannes Henrich and Gebhardt, Andreas},
  title     = {Machbarkeitsstudie zur Verarbeitung von nicht rostendem Stahl 1.4404 unter Verwendung einer Diodenlaser-basierten LPBF-Maschine mit kartesischem Achssystem},
  series = {RTejournal - Forum f{\"u}r Rapid Technologie},
  volume    = {15},
  journal   = {RTejournal - Forum f{\"u}r Rapid Technologie},
  issn      = {1614-0923},
  year      = {2018},
  language  = {de}
}
@article{RabehiGarlanAchtsnichtetal.2018,
  author    = {Rabehi, Amine and Garlan, Benjamin and Achtsnicht, Stefan and Krause, Hans-Joachim and Offenh{\"a}usser, Andreas and Ngo, Kieu and Neveu, Sophie and Graff-Dubois, Stephanie and Kokabi, Hamid},
  title     = {Magnetic detection structure for Lab-on-Chip applications based on the frequency mixing technique},
  series = {Sensors},
  volume    = {18},
  journal   = {Sensors},
  number    = {6},
  publisher = {MDPI},
  address   = {Basel},
  issn      = {1424-8220},
  doi       = {10.3390/s18061747},
  pages     = {14 Seiten},
  year      = {2018},
  abstract  = {A magnetic frequency mixing technique with a set of miniaturized planar coils was investigated for use with a completely integrated Lab-on-Chip (LoC) pathogen sensing system. The system allows the detection and quantification of superparamagnetic beads. Additionally, in terms of magnetic nanoparticle characterization ability, the system can be used for immunoassays using the beads as markers. Analytical calculations and simulations for both excitation and pick-up coils are presented; the goal was to investigate the miniaturization of simple and cost-effective planar spiral coils. Following these calculations, a Printed Circuit Board (PCB) prototype was designed, manufactured, and tested for limit of detection, linear response, and validation of theoretical concepts. Using the magnetic frequency mixing technique, a limit of detection of 15 µg/mL of 20 nm core-sized nanoparticles was achieved without any shielding.},
  language  = {en}
}
@article{EngelmannBuhlDraacketal.2018,
  author    = {Engelmann, Ulrich M. and Buhl, Eva Miriam and Draack, Sebastian and Viereck, Thilo and Frank, and Schmitz-Rode, Thomas and Slabu, Ioana},
  title     = {Magnetic relaxation of agglomerated and immobilized iron oxide nanoparticles for hyperthermia and imaging applications},
  series = {IEEE Magnetic Letters},
  volume    = {9},
  journal   = {IEEE Magnetic Letters},
  number    = {Article number 8519617},
  publisher = {IEEE},
  address   = {New York, NY},
  issn      = {1949-307X},
  doi       = {10.1109/LMAG.2018.2879034},
  year      = {2018},
  abstract  = {Magnetic nanoparticles (MNPs) are used as therapeutic and diagnostic agents for local delivery of heat and image contrast enhancement in diseased tissue. Besides magnetization, the most important parameter that determines their performance for these applications is their magnetic relaxation, which can be affected when MNPs immobilize and agglomerate inside tissues. In this letter, we investigate different MNP agglomeration states for their magnetic relaxation properties under excitation in alternating fields and relate this to their heating efficiency and imaging properties. With focus on magnetic fluid hyperthermia, two different trends in MNP heating efficiency are measured: an increase by up to 23\% for agglomerated MNP in suspension and a decrease by up to 28\% for mixed states of agglomerated and immobilized MNP, which indicates that immobilization is the dominant effect. The same comparatively moderate effects are obtained for the signal amplitude in magnetic particle spectroscopy.},
  language  = {en}
}
@article{OttenWeberArent2018,
  author    = {Otten, Dennis and Weber, Tobias and Arent, Jan-Christoph},
  title     = {Manufacturing Process Simulation - On Its Way to Industrial Application},
  series = {International Journal of Aviation, Aeronautics, and Aerospace},
  volume    = {5},
  journal   = {International Journal of Aviation, Aeronautics, and Aerospace},
  number    = {2},
  publisher = {Embry-Riddle Aeronautical University},
  address   = {Daytona Beach, Fla.},
  issn      = {2374-6793},
  doi       = {10.15394/ijaaa.2018.1217},
  year      = {2018},
  abstract  = {Manufacturing process simulation (MPS) has become more and more important for aviation and the automobile industry. A highly competitive market requires the use of high performance metals and composite materials in combination with reduced manufacturing cost and time as well as a minimization of the time to market for a new product. However, the use of such materials is expensive and requires sophisticated manufacturing processes. An experience based process and tooling design followed by a lengthy trial-and-error optimization is just not contemporary anymore. Instead, a tooling design process aided by simulation is used more often. This paper provides an overview of the capabilities of MPS in the fields of sheet metal forming and prepreg autoclave manufacturing of composite parts summarizing the resulting benefits for tooling design and manufacturing engineering. The simulation technology is explained briefly in order to show several simplification and optimization techniques for developing industrialized simulation approaches. Small case studies provide examples of an efficient application on an industrial scale.},
  language  = {en}
}
@article{AltherrEdererPfetschetal.2018,
  author    = {Altherr, Lena and Ederer, Thorsten and Pfetsch, Marc E. and Pelz, Peter F.},
  title     = {Maschinelles Design eines optimalen Getriebes},
  series = {ATZ - Automobiltechnische Zeitschrift},
  volume    = {120},
  journal   = {ATZ - Automobiltechnische Zeitschrift},
  number    = {10},
  publisher = {Springer Nature},
  address   = {Cham},
  isbn      = {2192-8800},
  doi       = {10.1007/s35148-018-0131-3},
  pages     = {72 -- 77},
  year      = {2018},
  abstract  = {Nahezu 100.000 denkbare Strukturen kann ein Getriebe bei gleicher Funktion aufweisen - je nach Ganganzahl und gefordertem Freiheitsgrad. Mit dem traditionellen Ansatz bei der Entwicklung, einzelne vielversprechende Systemkonfigurationen manuell zu identifizieren und zu vergleichen, k{\"o}nnen leicht innovative und vor allem kostenminimale L{\"o}sungen {\"u}bersehen werden. Im Rahmen eines Forschungsprojekts hat die TU Darmstadt spezielle Optimierungsmethoden angewendet, um auch bei großen L{\"o}sungsr{\"a}umen zielsicher ein f{\"u}r die individuellen Zielstellungen optimales Layout zu finden.},
  language  = {de}
}
@article{RiekeStollenwerkDahmenetal.2018,
  author    = {Rieke, Christian and Stollenwerk, Dominik and Dahmen, Markus and Pieper, Martin},
  title     = {Modeling and optimization of a biogas plant for a demand-driven energy supply},
  series = {Energy},
  volume    = {145},
  journal   = {Energy},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {0360-5442},
  doi       = {10.1016/j.energy.2017.12.073},
  pages     = {657 -- 664},
  year      = {2018},
  abstract  = {Due to the Renewable Energy Act, in Germany it is planned to increase the amount of renewable energy carriers up to 60\%. One of the main problems is the fluctuating supply of wind and solar energy. Here biogas plants provide a solution, because a demand-driven supply is possible. Before running such a plant, it is necessary to simulate and optimize the process. This paper provides a new model of a biogas plant, which is as accurate as the standard ADM1 model. The advantage compared to ADM1 is that it is based on only four parameters compared to 28. Applying this model, an optimization was installed, which allows a demand-driven supply by biogas plants. Finally the results are confirmed by several experiments and measurements with a real test plant.},
  language  = {en}
}
@article{BhattaraiStaat2018,
  author    = {Bhattarai, Aroj and Staat, Manfred},
  title     = {Modelling of Soft Connective Tissues to Investigate Female Pelvic Floor Dysfunctions},
  series = {Computational and Mathematical Methods in Medicine},
  volume    = {2018},
  journal   = {Computational and Mathematical Methods in Medicine},
  number    = {Article ID 9518076},
  publisher = {Hindawi},
  address   = {New York, NY},
  issn      = {1748-6718},
  doi       = {10.1155/2018/9518076},
  pages     = {1 -- 16},
  year      = {2018},
  abstract  = {After menopause, decreased levels of estrogen and progesterone remodel the collagen of the soft tissues thereby reducing their stiffness. Stress urinary incontinence is associated with involuntary urine leakage due to pathological movement of the pelvic organs resulting from lax suspension system, fasciae, and ligaments. This study compares the changes in the orientation and position of the female pelvic organs due to weakened fasciae, ligaments, and their combined laxity. A mixture theory weighted by respective volume fraction of elastin-collagen fibre compound (5\%), adipose tissue (85\%), and smooth muscle (5\%) is adopted to characterize the mechanical behaviour of the fascia. The load carrying response (other than the functional response to the pelvic organs) of each fascia component, pelvic organs, muscles, and ligaments are assumed to be isotropic, hyperelastic, and incompressible. Finite element simulations are conducted during Valsalva manoeuvre with weakened tissues modelled by reduced tissue stiffness. A significant dislocation of the urethrovesical junction is observed due to weakness of the fascia (13.89 mm) compared to the ligaments (5.47 mm). The dynamics of the pelvic floor observed in this study during Valsalva manoeuvre is associated with urethral-bladder hypermobility, greater levator plate angulation, and positive Q-tip test which are observed in incontinent females.},
  language  = {en}
}
@article{KlubertMalechaSparla2018,
  author    = {Klubert, Joachim and Malecha, Hartmut and Sparla, Peter},
  title     = {Modernisierung der geod{\"a}tischen Messtechnik der Urfttalsperre},
  series = {Wasserwirtschaft},
  volume    = {108},
  journal   = {Wasserwirtschaft},
  number    = {10},
  publisher = {Springer Vieweg},
  address   = {Wiesbaden},
  issn      = {0043-0978},
  pages     = {14 -- 18},
  year      = {2018},
  language  = {de}
}
@article{DruckenmuellerGuentherElbers2018,
  author    = {Druckenm{\"u}ller, Katharina and G{\"u}nther, Klaus and Elbers, Gereon},
  title     = {Near-infrared spectroscopy (NIRS) as a tool to monitor exhaust air from poultry operations},
  series = {Science of the Total Environment},
  volume    = {630},
  journal   = {Science of the Total Environment},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {0048-9697},
  doi       = {10.1016/j.scitotenv.2018.02.072},
  pages     = {536 -- 543},
  year      = {2018},
  abstract  = {Intensive poultry operation systems emit a considerable volume of inorganic and organic matter in the surrounding environment. Monitoring cleaning properties of exhaust air cleaning systems and to detect small but significant changes in emission characteristics during a fattening cycle is important for both emission and fattening process control. In the present study, we evaluated the potential of near-infrared spectroscopy (NIRS) combined with chemometric techniques as a monitoring tool of exhaust air from poultry operation systems. To generate a high-quality data set for evaluation, the exhaust air of two poultry houses was sampled by applying state-of-the-art filter sampling protocols. The two stables were identical except for one crucial difference, the presence or absence of an exhaust air cleaning system. In total, twenty-one exhaust air samples were collected at the two sites to monitor spectral differences caused by the cleaning device, and to follow changes in exhaust air characteristics during a fattening period. The total dust load was analyzed by gravimetric determination and included as a response variable in multivariate data analysis. The filter samples were directly measured with NIR spectroscopy. Principal component analysis (PCA), linear discriminant analysis (LDA), and factor analysis (FA) were effective in classifying the NIR exhaust air spectra according to fattening day and origin. The results indicate that the dust load and the composition of exhaust air (inorganic or organic matter) substantially influence the NIR spectral patterns. In conclusion, NIR spectroscopy as a tool is a promising and very rapid way to detect differences between exhaust air samples based on still not clearly defined circumstances triggered during a fattening period and the availability of an exhaust air cleaning system.},
  language  = {en}
}
@article{Lind2018,
  author    = {Lind, Thorsten Patric},
  title     = {Neues zur Gesch{\"a}ftsf{\"u}hrerhaftung nach \S 64 GmbHG - Zugleich Anmerkung zu BGH vom 19.12.2017 - II ZR 88/16, DB 2018 S. 307, und vom 04.07.2017 - II ZR 319/15, DB 2017 S. 1959 -},
  series = {Der Betrieb},
  journal   = {Der Betrieb},
  number    = {17},
  publisher = {Fachmedien Otto Schmidt},
  address   = {D{\"u}sseldorf},
  issn      = {0005-9935},
  pages     = {1003 -- 1008},
  year      = {2018},
  language  = {de}
}
@article{AlbannaKotliarLuekeetal.2018,
  author    = {Albanna, Walid and Kotliar, Konstantin and L{\"u}ke, Jan Niklas and Alpdogan, Serdar and Conzen, Catharina and Lindauer, Ute and Clusmann, Hans and Hescheler, J{\"u}rgen and Vilser, Walthard and Schneider, Toni and Schubert, Gerrit Alexander},
  title     = {Non-invasive evaluation of neurovascular coupling in the murine retina by dynamic retinal vessel analysis},
  series = {Plos one},
  volume    = {13},
  journal   = {Plos one},
  number    = {10},
  publisher = {PLOS},
  address   = {San Francisco},
  doi       = {10.1371/journal.pone.0204689},
  pages     = {e0204689},
  year      = {2018},
  abstract  = {Background Impairment of neurovascular coupling (NVC) was recently reported in the context of subarachnoid hemorrhage and may correlate with disease severity and outcome. However, previous techniques to evaluate NVC required invasive procedures. Retinal vessels may represent an alternative option for non-invasive assessment of NVC. Methods A prototype of an adapted retinal vessel analyzer was used to assess retinal vessel diameter in mice. Dynamic vessel analysis (DVA) included an application of monochromatic flicker light impulses in predefined frequencies for evaluating NVC. All retinae were harvested after DVA and electroretinograms were performed. Results A total of 104 retinal scans were conducted in 21 male mice (90 scans). Quantitative arterial recordings were feasible only in a minority of animals, showing an emphasized reaction to flicker light impulses (8 mice; 14 scans). A characteristic venous response to flicker light, however, could observed in the majority of animals. Repeated measurements resulted in a significant decrease of baseline venous diameter (7 mice; 7 scans, p < 0.05). Ex-vivo electroretinograms, performed after in-vivo DVA, demonstrated a significant reduction of transretinal signaling in animals with repeated DVA (n = 6, p < 0.001). Conclusions To the best of our knowledge, this is the first non-invasive study assessing murine retinal vessel response to flicker light with characteristic changes in NVC. The imaging system can be used for basic research and enables the investigation of retinal vessel dimension and function in control mice and genetically modified animals.},
  language  = {en}
}
@article{AltherrJoggerstLeiseetal.2018,
  author    = {Altherr, Lena and Joggerst, Laura and Leise, Philipp and Pfetsch, Marc E. and Schmitt, Andreas and Wendt, Janine},
  title     = {On obligations in the development process of resilient systems with algorithmic design methods},
  series = {Applied Mechanics and Materials},
  volume    = {885},
  journal   = {Applied Mechanics and Materials},
  number    = {885},
  publisher = {Trans Tech Publications},
  address   = {B{\"a}ch},
  isbn      = {1662-7482},
  doi       = {10.4028/www.scientific.net/AMM.885.240},
  pages     = {240 -- 252},
  year      = {2018},
  abstract  = {Advanced computational methods are needed both for the design of large systems and to compute high accuracy solutions. Such methods are efficient in computation, but the validation of results is very complex, and highly skilled auditors are needed to verify them. We investigate legal questions concerning obligations in the development phase, especially for technical systems developed using advanced methods. In particular, we consider methods of resilient and robust optimization. With these techniques, high performance solutions can be found, despite a high variety of input parameters. However, given the novelty of these methods, it is uncertain whether legal obligations are being met. The aim of this paper is to discuss if and how the choice of a specific computational method affects the developer's product liability. The review of legal obligations in this paper is based on German law and focuses on the requirements that must be met during the design and development process.},
  language  = {en}
}
@article{ZhangValeroBungetal.2018,
  author    = {Zhang, G. and Valero, Daniel and Bung, Daniel Bernhard and Chanson, H.},
  title     = {On the estimation of free-surface turbulence using ultrasonic sensors},
  series = {Flow Measurement and Instrumentation},
  volume    = {60},
  journal   = {Flow Measurement and Instrumentation},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {0955-5986},
  doi       = {10.1016/j.flowmeasinst.2018.02.009},
  pages     = {171 -- 184},
  year      = {2018},
  abstract  = {Accurate determination of free-surface dynamics has attracted much research attention during the past decade and has important applications in many environmental and water related areas. In this study, the free-surface dynamics in several turbulent flows commonly found in nature were investigated using a synchronised setup consisting of an ultrasonic sensor and a high-speed video camera. Basic sensor capabilities were examined in dry conditions to allow for a better characterisation of the present sensor model. The ultrasonic sensor was found to adequately reproduce free-surface dynamics up to the second order, especially in two-dimensional scenarios with the most energetic modes in the low frequency range. The sensor frequency response was satisfactory in the sub-20 Hz band, and its signal quality may be further improved by low-pass filtering prior to digitisation. The application of the USS to characterise entrapped air in high-velocity flows is also discussed.},
  language  = {en}
}
@article{GoettenFingerHavermannetal.2018,
  author    = {G{\"o}tten, Falk and Finger, Felix and Havermann, Marc and Braun, Carsten and Gomez, Francisco and Bill, C.},
  title     = {On the flight performance impact of landing gear drag reduction methods for unmanned air vehicles},
  series = {Deutscher Luft- und Raumfahrtkongress 2018},
  journal   = {Deutscher Luft- und Raumfahrtkongress 2018},
  publisher = {DGLR},
  address   = {Bonn},
  doi       = {10.25967/480058},
  pages     = {11 S.},
  year      = {2018},
  abstract  = {The flight performance impact of three different landing gear configurations on a small, fixed-wing UAV is analyzed with a combination of RANS CFD calculations and an incremental flight performance algorithm. A standard fixed landing gear configuration is taken as a baseline, while the influence of retracting the landing gear or applying streamlined fairings is investigated. A retraction leads to a significant parasite drag reduction, while also fairings promise large savings. The increase in lift-to-drag ratio is reduced at high lift coefficients due to the influence of induced drag. All configurations are tested on three different design missions with an incremental flight performance algorithm. A trade-off study is performed using the retracted or faired landing gear's weight increase as a variable. The analysis reveals only small mission performance gains as the aerodynamic improvements are negated by weight penalties. A new workflow for decision-making is presented that allows to estimate if a change in landing gear configuration is beneficial for a small UAV.},
  language  = {en}
}
@article{HorbachStaat2018,
  author    = {Horbach, Andreas and Staat, Manfred},
  title     = {Optical strain measurement for the modeling of surgical meshes and their porosity},
  series = {Current Directions in Biomedical Engineering},
  volume    = {Band 4},
  journal   = {Current Directions in Biomedical Engineering},
  number    = {1},
  publisher = {De Gruyter},
  address   = {Berlin},
  issn      = {2364-5504},
  doi       = {10.1515/cdbme-2018-0045},
  pages     = {181 -- 184},
  year      = {2018},
  abstract  = {The porosity of surgical meshes makes them flexible for large elastic deformation and establishes the healing conditions of good tissue in growth. The biomechanic modeling of orthotropic and compressible materials requires new materials models and simulstaneoaus fit of deformation in the load direction as well as trannsversely to to load. This nonlinear modeling can be achieved by an optical deformation measurement. At the same time the full field deformation measurement allows the dermination of the change of porosity with deformation. Also the socalled effective porosity, which has been defined to asses the tisssue interatcion with the mesh implants, can be determined from the global deformation of the surgical meshes.},
  language  = {en}
}
@article{SunAltherrPeietal.2018,
  author    = {Sun, Hui and Altherr, Lena and Pei, Ji and Pelz, Peter F. and Yuan, Shouqi},
  title     = {Optimal booster station design and operation under uncertain load},
  series = {Applied Mechanics and Materials},
  volume    = {885},
  journal   = {Applied Mechanics and Materials},
  publisher = {Trans Tech Publications},
  address   = {B{\"a}ch},
  issn      = {1662-7482},
  doi       = {10.4028/www.scientific.net/AMM.885.102},
  pages     = {102 -- 115},
  year      = {2018},
  abstract  = {Given industrial applications, the costs for the operation and maintenance of a pump system typically far exceed its purchase price. For finding an optimal pump configuration which minimizes not only investment, but life-cycle costs, methods like Technical Operations Research which is based on Mixed-Integer Programming can be applied. However, during the planning phase, the designer is often faced with uncertain input data, e.g. future load demands can only be estimated. In this work, we deal with this uncertainty by developing a chance-constrained two-stage (CCTS) stochastic program. The design and operation of a booster station working under uncertain load demand are optimized to minimize total cost including purchase price, operation cost incurred by energy consumption and penalty cost resulting from water shortage. We find optimized system layouts using a sample average approximation (SAA) algorithm, and analyze the results for different risk levels of water shortage. By adjusting the risk level, the costs and performance range of the system can be balanced, and thus the system's resilience can be engineered},
  language  = {en}
}
@article{DantismRoehlenWagneretal.2018,
  author    = {Dantism, Shahriar and R{\"o}hlen, Desiree and Wagner, Torsten and Wagner, Patrick and Sch{\"o}ning, Michael Josef},
  title     = {Optimization of Cell-Based Multi-Chamber LAPS Measurements Utilizing FPGA-Controlled Laser-Diode Modules},
  series = {physica status solidi a : applications and materials sciences},
  volume    = {215},
  journal   = {physica status solidi a : applications and materials sciences},
  number    = {15},
  publisher = {Wiley-VCH},
  address   = {Weinheim},
  issn      = {1862-6319},
  doi       = {10.1002/pssa.201800058},
  pages     = {Article number 1800058},
  year      = {2018},
  abstract  = {A light-addressable potentiometric sensor (LAPS) is a field-effect-based potentiometric device, which detects concentration changes of an analyte solution on the sensor surface in a spatially resolved way. It uses a light source to generate electron-hole pairs inside the semiconductor, which are separated in the depletion region due to an applied bias voltage across the sensor structure and hence, a surface-potential-dependent photocurrent can be read out. However, depending on the beam angle of the light source, scattering effects can occur, which influence the recorded signal in LAPS-based differential measurements. To solve this problem, a novel illumination unit based on a field programmable gate array (FPGA) consisting of 16 small-sized tunable infrared laser-diode modules (LDMs) is developed. Due to the improved focus of the LDMs with a beam angle of only 2 mrad, undesirable scattering effects are minimized. Escherichia coli (E. coli) K12 bacteria are used as a test microorganism to study the extracellular acidification on the sensor surface. Furthermore, a salt bridge chamber is built up and integrated with the LAPS system enabling multi-chamber differential measurements with a single Ag/AgCl reference electrode.},
  language  = {en}
}
@article{KohlerKirschnerHermannsStaatetal.2018,
  author    = {Kohler, Annette and Kirschner-Hermanns, Ruth and Staat, Manfred and Brehmer, Bernhard},
  title     = {Pathogenese, funktionelle und anatomische Aspekte der weiblichen Belastungsinkontinenz},
  series = {Aktuelle Urologie},
  volume    = {49},
  journal   = {Aktuelle Urologie},
  number    = {1},
  publisher = {Thieme},
  address   = {Stuttgart},
  issn      = {1438-8820},
  doi       = {10.1055/s-0043-120616},
  pages     = {47 -- 51},
  year      = {2018},
  abstract  = {Der vorliegende Artikel fokussiert sich auf die weibliche Belastungsinkontinenz als Insuffizienz der Speicherfunktion der Blase, auch wenn im klinischen Alltag die Harninkontinenz der Frau h{\"a}ufig verschiedene Ursachen hat und insbesondere eine Belastungsinkontinenz im Alter und bei neurologischer Komorbidit{\"a}t nur selten isoliert vorkommt. Das kleine Becken der Frau ist sowohl als Funktions- als auch als strukturelle Einheit zu betrachten. Dabei unterliegen bei der Frau Blase, Harnr{\"o}hre, Geb{\"a}rmutter und Enddarm sowie die muskul{\"a}ren und ligament{\"o}sen Strukturen des kleinen Beckens durch Fertilit{\"a}tsphase, m{\"o}gliche Schwangerschaften, Geburten und Menopausen-Phase, {\"u}ber das „normale Altern" hinaus, gravierenden Ver{\"a}nderungen. This article focuses on female stress incontinence in the form of pelvic floor dysfunction and urethral sphincter deficiency, although isolated stress incontinence accounts for less than half of all incontinence cases. Especially in women of old age and those with neurological comorbidities, the causes of incontinence are mostly multifactorial. Also it has to be considered that the female bladder, urethra, uterus and rectum as well as the muscular and ligamentous structures of the female pelvis minor are affected by phases of fertility, possible pregnancies, births and menopause in addition to the normal ageing process.},
  language  = {de}
}