@inproceedings{WeissAbanteribaEsch2007,
  author    = {Weiss, Alexander and Abanteriba, Sylvester and Esch, Thomas},
  title     = {Investigation of Flow Separation Inside a Conical Rocket Nozzle With the Aid of an Annular Cross Flow},
  series = {Proceedings of the ASME/JSME 2007 5th Joint Fluids Engineering Conference. Volume 1: Symposia, Parts A and B},
  booktitle = {Proceedings of the ASME/JSME 2007 5th Joint Fluids Engineering Conference. Volume 1: Symposia, Parts A and B},
  publisher = {American Society of Mechanical Engineers (ASME)},
  address   = {New York},
  isbn      = {0-7918-4288-6},
  doi       = {10.1115/FEDSM2007-37387},
  pages     = {1861 -- 1871},
  year      = {2007},
  abstract  = {Flow separation is a phenomenon that occurs in all kinds of supersonic nozzles sometimes during run-up and shut-down operations. Especially in expansion nozzles of rocket engines with large area ratio, flow separation can trigger strong side loads that can damage the structure of the nozzle. The investigation presented in this paper seeks to establish measures that may be applied to alter the point of flow separation. In order to achieve this, a supersonic nozzle was placed at the exit plane of the conical nozzle. This resulted in the generation of cross flow surrounding the core jet flow from the conical nozzle. Due to the entrainment of the gas stream from the conical nozzle the pressure in its exit plane was found to be lower than that of the ambient. A Cold gas instead of hot combustion gases was used as the working fluid. A mathematical simulation of the concept was validated by experiment. Measurements confirmed the simulation results that due to the introduction of a second nozzle the pressure in the separated region of the conical nozzle was significantly reduced. It was also established that the boundary layer separation inside the conical nozzle was delayed thus allowing an increased degree of overexpansion. The condition established by the pressure measurements was also demonstrated qualitatively using transparent nozzle configurations.},
  language  = {en}
}
@inproceedings{HuberBleckScheiketal.2011,
  author    = {Huber, Fr{\´e}d{\´e}ric and Bleck, Wolfgang and Scheik, Sven and Schleser, Markus and Reisgen, Uwe},
  title     = {Investigation of galvanneal coating adherence in adhesive bonded joints using lap shear test},
  series = {Galvatech 2011 : 8th International Conference on Zinc and Zinc Alloy Coated Steel Sheet, June 21 - 24, 2011, Genova (Italy) ; proceedings},
  booktitle = {Galvatech 2011 : 8th International Conference on Zinc and Zinc Alloy Coated Steel Sheet, June 21 - 24, 2011, Genova (Italy) ; proceedings},
  publisher = {Associazione Italiana di Metallurgia},
  address   = {Mailand},
  organization    = {International Conference on Zinc and Zinc Alloy Coated Steel Sheet <8, 2011, Genua>},
  isbn      = {978-88-85298-82-8},
  pages     = {Paper No. 43},
  year      = {2011},
  language  = {en}
}
@inproceedings{KubalskiButenwegMarinkovićetal.2017,
  author    = {Kubalski, T. and Butenweg, Christoph and Marinković, Marko and Klinkel, S.},
  title     = {Investigation Of The Seismic Behaviour Of Infill Masonry Using Numerical Modelling Approaches},
  series = {16th World Conference on Earthquake Engineering, 16WCEE 2017 Santiago Chile, January 9th to 13th 2017},
  booktitle = {16th World Conference on Earthquake Engineering, 16WCEE 2017 Santiago Chile, January 9th to 13th 2017},
  publisher = {Chilean Association on Seismology and Earthquake Engineering (ACHISINA)},
  pages     = {1 -- 11},
  year      = {2017},
  abstract  = {Masonry is a widely spread construction type which is used all over the world for different types of structures. Due to its simple and cheap construction, it is used as non-structural as well as structural element. In frame structures, such as reinforced concrete frames, masonry may be used as infill. While the bare frame itself is able to carry the loads when it comes to seismic events, the infilled frame is not able to warp freely due to the constrained movement. This restraint results in a complex interaction between the infill and the surrounding frame, which may lead to severe damage to the infill as well as the surrounding frame. The interaction is studied in different projects and effective approaches for the description of the behavior are still lacking. Experimental programs are usually quite expensive, while numerical models, once validated, do offer an efficient approach for the investigation of the interaction when horizontally loaded. In order to study the numerous parameters influencing the seismic load bearing behavior, numerical models may be used. Therefore, this contribution presents a numerical approach for the simulation of infill masonry in reinforced concrete frames. Both parts, the surrounding frame as well as the infill are represented by micro modelling approaches to correctly take into account the different types of failure. The adopted numerical model describes the inelastic behavior of the system, as indicated by the obtained results of the overall structural response as well as the formation of damage in the infilled wall. Comparison of the numerical and experimental results highlights the valuable contribution of numerical simulations in the study and design of infilled frames. As damage of the infill masonry may occur in-plane due to the interaction as well as out-of-plane due to the low vertical load, both directions of loading are investigated.},
  language  = {en}
}
@inproceedings{MarkinkovicButenwegPaveseetal.2020,
  author    = {Markinkovic, Marko and Butenweg, Christoph and Pavese, A. and Lanese, I. and Hoffmeister, B. and Pinkawa, M. and Vulcu, C. and Bursi, O. and Nardin, C. and Paolacci, F. and Quinci, G. and Fragiadakis, M. and Weber, F. and Huber, P. and Renault, P. and G{\"u}ndel, M. and Dyke, S. and Ciucci, M. and Marino, A.},
  title     = {Investigation of the seismic behaviour of structural and nonstructural components in industrial facilities by means of shaking table tests},
  series = {Seismic design of industrial facilities 2020: proceedings of the 2nd International Conference on Seismic Design of Industrial Facilities (SeDIF-Conference)},
  booktitle = {Seismic design of industrial facilities 2020: proceedings of the 2nd International Conference on Seismic Design of Industrial Facilities (SeDIF-Conference)},
  isbn      = {978-3-86359-729-0},
  pages     = {159 -- 172},
  year      = {2020},
  language  = {en}
}
@inproceedings{ReisgenSchleserSchoeneetal.2012,
  author    = {Reisgen, Uwe and Schleser, Markus and Schoene, Jens and Hegger, Josef and Gallwoszus, J{\"o}rg and Feldmann, Markus and Kopp, Maik and G{\"u}ndel, Max},
  title     = {Investigation on bond mechanisms of innovative small-scale shear connectors between steel and concrete},
  series = {Bond in concrete 2012. Vol. 2. Bond in new materials and under severe conditions},
  booktitle = {Bond in concrete 2012. Vol. 2. Bond in new materials and under severe conditions},
  editor    = {Cairns, John W.},
  publisher = {Publisher creations},
  address   = {Manerbio, Brescia},
  isbn      = {978-88-907078-3-4},
  pages     = {893 -- 898},
  year      = {2012},
  language  = {en}
}
@inproceedings{SchoppHeuermannHoltrup2014,
  author    = {Schopp, Christoph and Heuermann, Holger and Holtrup, S.},
  title     = {Investigation on efficacy optimization of RF-driven automotive D-lamps},
  series = {44th European Microwave Conference (EuMC),2014, Rome},
  booktitle = {44th European Microwave Conference (EuMC),2014, Rome},
  doi       = {10.1109/EuMC.2014.6986645},
  pages     = {1154 -- 1157},
  year      = {2014},
  language  = {en}
}
@inproceedings{WeissHeslenfeldSaeweetal.2022,
  author    = {Weiss, Christian and Heslenfeld, Jonas and Saewe, Jasmin Kathrin and Bremen, Sebastian and H{\"a}fner, Constantin Leon},
  title     = {Investigation on the influence of powder humidity in Laser Powder Bed Fusion (LPBF)},
  series = {Procedia CIRP},
  volume    = {111},
  booktitle = {Procedia CIRP},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {2212-8271},
  doi       = {10.1016/j.procir.2022.08.102},
  pages     = {115 -- 120},
  year      = {2022},
  abstract  = {In the Laser Powder Bed Fusion (LPBF) process, parts are built out of metal powder material by exposure of a laser beam. During handling operations of the powder material, several influencing factors can affect the properties of the powder material and therefore directly influence the processability during manufacturing. Contamination by moisture due to handling operations is one of the most critical aspects of powder quality. In order to investigate the influences of powder humidity on LPBF processing, four materials (AlSi10Mg, Ti6Al4V, 316L and IN718) are chosen for this study. The powder material is artificially humidified, subsequently characterized, manufactured into cubic samples in a miniaturized process chamber and analyzed for their relative density. The results indicate that the processability and reproducibility of parts made of AlSi10Mg and Ti6Al4V are susceptible to humidity, while IN718 and 316L are barely influenced.},
  language  = {en}
}
@inproceedings{HeinzOertelBung2010,
  author    = {Heinz, G. and Oertel, Mario and Bung, Daniel B.},
  title     = {Investigations on a cooling water system for a gas tubine facility concerning air vortexes and sediment transport},
  series = {Hydraulic structures: useful water harvesting systems or relics? : Third International Junior Researcher and Engineer Workshop on Hydraulic Structures (IJREWHS'10) : Edinburgh, Scotland, U.K., 2-3 May 2010},
  booktitle = {Hydraulic structures: useful water harvesting systems or relics? : Third International Junior Researcher and Engineer Workshop on Hydraulic Structures (IJREWHS'10) : Edinburgh, Scotland, U.K., 2-3 May 2010},
  editor    = {Janssen, Robert},
  publisher = {School of Civil Engineering, The University of Queensland},
  address   = {Brisbane},
  organization    = {International Junior Researcher and Engineer Workshop on Hydraulic Structures <3, 2010, Edinburgh>},
  isbn      = {9781742720159},
  pages     = {109 -- 116},
  year      = {2010},
  language  = {en}
}
@inproceedings{Sauerborn2011,
  author    = {Sauerborn, Markus},
  title     = {Investigations to the influence of clouds and aerosols to the haze of the sunshape},
  series = {SolarPACES 2011 : concentrating solar power and chemical energy systems : 20 - 23 September, 2011, Granada, Spain},
  booktitle = {SolarPACES 2011 : concentrating solar power and chemical energy systems : 20 - 23 September, 2011, Granada, Spain},
  address   = {Granada},
  pages     = {1 CD-ROM},
  year      = {2011},
  language  = {en}
}
@inproceedings{BegingPoghossianMlyneketal.2010,
  author    = {Beging, Stefan and Poghossian, Arshak and Mlynek, D. and Hataihimakul, S. and Pedraza, A. and Dhawan, S. and Laube, N. and Kleinen, L. and Baldsiefen, G. and Busch, H. and Sch{\"o}ning, Michael Josef},
  title     = {Ion-selective sensors for the determination of the risk of urinary stone formation},
  series = {Micro- and Nanosystems in biochemical diagnosis : Principles and applications},
  booktitle = {Micro- and Nanosystems in biochemical diagnosis : Principles and applications},
  address   = {Warsaw},
  pages     = {74 -- 80},
  year      = {2010},
  language  = {en}
}
@inproceedings{BrockmannSultanowCzarnecki2019,
  author    = {Brockmann, Carsten and Sultanow, Eldar and Czarnecki, Christian},
  title     = {Is enterprise architecture still relevant in the digital age?},
  series = {GI Edition Proceedings Band 295 INFORMATIK 2019, Workshop-Beitr{\"a}ge},
  booktitle = {GI Edition Proceedings Band 295 INFORMATIK 2019, Workshop-Beitr{\"a}ge},
  editor    = {Draude, Claude and Lange, Martin and Sick, Bernhard},
  publisher = {K{\"o}llen},
  address   = {Bonn},
  isbn      = {9783885796893},
  issn      = {1617-5468},
  doi       = {10.18420/inf2019_ws01},
  pages     = {21 -- 21},
  year      = {2019},
  language  = {en}
}
@inproceedings{KolditzAlbinAlbrachtetal.2016,
  author    = {Kolditz, Melanie and Albin, Thivaharan and Albracht, Kirsten and Br{\"u}ggemann, Gert-Peter and Abel, Dirk},
  title     = {Isokinematic leg extension training with an industrial robot},
  series = {6th IEEE RAS/EMBS International Conference on Biomedical Robotics and Biomechatronics (BioRob) June 26-29, 2016. UTown, Singapore},
  booktitle = {6th IEEE RAS/EMBS International Conference on Biomedical Robotics and Biomechatronics (BioRob) June 26-29, 2016. UTown, Singapore},
  doi       = {10.1109/BIOROB.2016.7523750},
  pages     = {950 -- 955},
  year      = {2016},
  language  = {de}
}
@inproceedings{BeckerHoefkenSchuetzetal.2016,
  author    = {Becker, Sebastian and H{\"o}fken, Hans-Wilhelm and Sch{\"u}tz, Philip and Schuba, Marko},
  title     = {IT-forensische Erkennung modifizierter Android-Apps},
  series = {Proceedings of DACH Security 2016, Klagenfurt, Austria, September 2016},
  booktitle = {Proceedings of DACH Security 2016, Klagenfurt, Austria, September 2016},
  editor    = {Schartner, P.},
  pages     = {120 -- 125},
  year      = {2016},
  abstract  = {Malware auf Smartphones ist ein Problem, dem auch Strafverfolgungsbeh{\"o}rden immer h{\"a}ufiger gegen{\"u}berstehen. Insbesondere Telefone, bei denen potentiell schadhafte Apps zu einem finanziellen Schaden gef{\"u}hrt haben, finden sich auf den Schreibtischen der Polizei wieder. Dabei m{\"u}ssen die Ermittler m{\"o}glichst schnell und gezielt erkennen k{\"o}nnen, ob eine App tats{\"a}chlich schadhaft manipuliert wurde, was manipuliert wurde und mit wem die App kommuniziert. Klassische Malware-Erkennungsverfahren helfen zwar bei der generellen Erkennung schadhafter Software, sind aber f{\"u}r die polizeiliche Praxis nicht geeignet. Dieses Paper stellt ein Programm vor, welches gerade die forensischen Fragestellungen ber{\"u}cksichtigt und so f{\"u}r den Einsatz in der Strafverfolgung in Frage kommt.},
  language  = {de}
}
@inproceedings{HartungHillgaertnerSchmitzetal.2014,
  author    = {Hartung, Frank and Hillg{\"a}rtner, Michael and Schmitz, G{\"u}nter and Schuba, Marko and Adolphs, Fabian and Hoffend, Jens and Theis, Jochen},
  title     = {IT-Sicherheit im Automobil},
  series = {AmE 2014 : Automotive meets Electronics, Beitr{\"a}ge der 5. GMM-Fachtagung vom 18. bis 19. Februar 2014 in Dortmund. (GMM-Fachbericht ; 78)},
  booktitle = {AmE 2014 : Automotive meets Electronics, Beitr{\"a}ge der 5. GMM-Fachtagung vom 18. bis 19. Februar 2014 in Dortmund. (GMM-Fachbericht ; 78)},
  publisher = {VDE-Verl.},
  address   = {Berlin},
  organization    = {VDE/VDI-Gesellschaft Mikroelektronik, Mikrosystem- und Feinwerktechnik (GMM)},
  isbn      = {978-3-8007-3580-8},
  pages     = {CD-ROM},
  year      = {2014},
  language  = {de}
}
@inproceedings{KetelhutGoellBraunsteinetal.2019,
  author    = {Ketelhut, Maike and G{\"o}ll, Fabian and Braunstein, Bjoern and Albracht, Kirsten and Abel, Dirk},
  title     = {Iterative learning control of an industrial robot for neuromuscular training},
  series = {2019 IEEE Conference on Control Technology and Applications},
  booktitle = {2019 IEEE Conference on Control Technology and Applications},
  publisher = {IEEE},
  address   = {New York},
  isbn      = {978-1-7281-2767-5 (ePub)},
  doi       = {10.1109/CCTA.2019.8920659},
  pages     = {7 Seiten},
  year      = {2019},
  abstract  = {Effective training requires high muscle forces potentially leading to training-induced injuries. Thus, continuous monitoring and controlling of the loadings applied to the musculoskeletal system along the motion trajectory is required. In this paper, a norm-optimal iterative learning control algorithm for the robot-assisted training is developed. The algorithm aims at minimizing the external knee joint moment, which is commonly used to quantify the loading of the medial compartment. To estimate the external knee joint moment, a musculoskeletal lower extremity model is implemented in OpenSim and coupled with a model of an industrial robot and a force plate mounted at its end-effector. The algorithm is tested in simulation for patients with varus, normal and valgus alignment of the knee. The results show that the algorithm is able to minimize the external knee joint moment in all three cases and converges after less than seven iterations.},
  language  = {en}
}
@inproceedings{FateriGebhardt2014,
  author    = {Fateri, Miranda and Gebhardt, Andreas},
  title     = {Jewelry fabrication via selective laser melting of glass},
  series = {ASME 2014 12th Biennial Conference on Engineering Systems Design and Analysis Volume 1: Applied Mechanics; Automotive Systems; Biomedical Biotechnology Engineering; Computational Mechanics; Design; Digital Manufacturing; Education; Marine and Aerospace Applications},
  booktitle = {ASME 2014 12th Biennial Conference on Engineering Systems Design and Analysis Volume 1: Applied Mechanics; Automotive Systems; Biomedical Biotechnology Engineering; Computational Mechanics; Design; Digital Manufacturing; Education; Marine and Aerospace Applications},
  isbn      = {978-0-7918-4583-7},
  doi       = {10.1115/ESDA2014-20380},
  pages     = {V001T06A005},
  year      = {2014},
  abstract  = {Selective Laser Melting (SLM) is one of the Additive Manufacturing (AM) technologies applicable for producing complex geometries which are typically expensive or difficult to fabricate using conventional methods. This process has been extensively investigated experimentally for various metals and the fabrication process parameters have been established for different applications; however, fabricating 3D glass objects using SLM technology has remained a challenge so far although it could have many applications. This paper presents a summery on various experimental evaluations of a material database incorporating the build parameters of glass powder using the SLM process for jewelry applications.},
  language  = {en}
}
@inproceedings{Gligorevic2002,
  author    = {Gligorevic, Snjezana},
  title     = {Joint channel estimation and equalization for fast time-variant multipath channels},
  series = {Proceedings / 13th IEEE International Symposium on Personal, Indoor and Mobile Radio Communications : PIMRC 2002 : Lisboa, Portugal, September 15 - 18, 2002},
  booktitle = {Proceedings / 13th IEEE International Symposium on Personal, Indoor and Mobile Radio Communications : PIMRC 2002 : Lisboa, Portugal, September 15 - 18, 2002},
  organization    = {Institute of Electrical and Electronics Engineers},
  isbn      = {0-7803-7589-0},
  pages     = {1127 -- 1130},
  year      = {2002},
  language  = {en}
}
@inproceedings{HadinejadMahramGligorevicRitscher2002,
  author    = {Hadinejad-Mahram, Hafez and Gligorevic, Snjezana and Ritscher, Matthias},
  title     = {Joint iterative channel estimation and parallel interference cancellation for coded DS-CDMA},
  series = {Proceeding of the International Conference on Telecommunications 2002 : [Beijing, 23 - 26 June 2002]. Vol. 2},
  booktitle = {Proceeding of the International Conference on Telecommunications 2002 : [Beijing, 23 - 26 June 2002]. Vol. 2},
  organization    = {Institute of Electrical and Electronics Engineers},
  pages     = {566 -- 570},
  year      = {2002},
  language  = {en}
}
@inproceedings{BraunsteinGoldmannAlbrachtetal.2013,
  author    = {Braunstein, Bjoern and Goldmann, Jan-Peter and Albracht, Kirsten and Sanno, Maximilian and Willwacher, Steffen and Heinrich, Kai and Herrmann, Volker and Br{\"u}ggemann, Gert-Peter},
  title     = {Joint specific contribution of mechanical power and work during acceleration and top speed in elite sprinters},
  series = {31 International Conference on Biomechanics in Sports, Taipei, Taiwan, July 07 - July 22, 2013},
  booktitle = {31 International Conference on Biomechanics in Sports, Taipei, Taiwan, July 07 - July 22, 2013},
  issn      = {1999-4168},
  year      = {2013},
  language  = {en}
}
@inproceedings{GoldmannBraunsteinHeinrichetal.2015,
  author    = {Goldmann, Jan-Peter and Braunstein, Bjoern and Heinrich, Kai and Sanno, Maximilian and St{\"a}udle, Benjamin and Ritzdorf, Wolfgang and Br{\"u}ggemann, Gert-Peter and Albracht, Kirsten},
  title     = {Joint work of the take-off leg during elite high jump},
  series = {Proceedings of the 33th International Conference on Biomechanics in Sports (ISBS)},
  booktitle = {Proceedings of the 33th International Conference on Biomechanics in Sports (ISBS)},
  pages     = {3 S.},
  year      = {2015},
  language  = {en}
}
@inproceedings{UibelBlass2013,
  author    = {Uibel, Thomas and Blaß, Hans-Joachim},
  title     = {Joints with Dowel Type Fasteners in CLT structures},
  series = {Focus solid timber solutions : European Conference on Cross Laminated Timber (CLT); May 21-22, 2013, Graz University of Technology, Austria},
  booktitle = {Focus solid timber solutions : European Conference on Cross Laminated Timber (CLT); May 21-22, 2013, Graz University of Technology, Austria},
  organization    = {European Conference on Cross Laminated Timber <2013, Graz>},
  isbn      = {978-1-85790-181-8 ; 1-85790-181-9},
  pages     = {119 -- 134},
  year      = {2013},
  language  = {en}
}
@inproceedings{Hoepner2008,
  author    = {Hoepner, Gert},
  title     = {Jurorenstatement - Junioren zeigen sich aggressiv},
  organization    = {DDV Deutscher Dialogmarketing Verband e. V.},
  year      = {2008},
  abstract  = {Statement zu den Einreichung des DDP 2008},
  subject      = {Deutscher Direktmarketing-Verband},
  language  = {de}
}
@inproceedings{OberlaenderReisertKirchneretal.2013,
  author    = {Oberl{\"a}nder, Jan and Reisert, Steffen and Kirchner, Patrick and Wagner, Patrick and Sch{\"o}ning, Michael Josef},
  title     = {Kalorimetrische Gassensoren zur H2O2-Detektion in aseptischen Sterilisationsprozessen},
  series = {11. Dresdner Sensor-Symposium : 9.-11.12.2013},
  booktitle = {11. Dresdner Sensor-Symposium : 9.-11.12.2013},
  organization    = {Dresdner Sensor-Symposium <11, 2013>},
  isbn      = {978-3-9813484-5-3},
  pages     = {234 -- 238},
  year      = {2013},
  language  = {de}
}
@inproceedings{PinnekampMueller2006,
  author    = {Pinnekamp, Johannes and M{\"u}ller, Karsten},
  title     = {Kanalisation und Gew{\"a}sserschutz},
  series = {7. K{\"o}lner Kanal Kolloquium : 06. und 07. September 2006 im Maternushaus, K{\"o}ln / hrsg. von Johannes Pinnekamp. Aachener Schriften zur Stadtentw{\"a}sserung. Bd. 9},
  booktitle = {7. K{\"o}lner Kanal Kolloquium : 06. und 07. September 2006 im Maternushaus, K{\"o}ln / hrsg. von Johannes Pinnekamp. Aachener Schriften zur Stadtentw{\"a}sserung. Bd. 9},
  publisher = {Ges. zur F{\"o}rderung der Siedlungswasserwirtschaft an der RWTH Aachen},
  address   = {Aachen},
  isbn      = {3-938996-02-1},
  pages     = {1/1 -- 1/16},
  year      = {2006},
  language  = {de}
}
@inproceedings{AbelBoninAlbrachtetal.2010,
  author    = {Abel, Thomas and Bonin, Dominik and Albracht, Kirsten and Zeller, Sebastian and Br{\"u}ggemann, Gert-Peter and Burkett, Brendan and Str{\"u}der, Heiko K.},
  title     = {Kinematic profile of the elite handcyclist},
  series = {28th International Conference on Biomechanics in Sports, Marquette, Michigan, USA, July 19 - 23, 2010},
  booktitle = {28th International Conference on Biomechanics in Sports, Marquette, Michigan, USA, July 19 - 23, 2010},
  issn      = {1999-4168},
  pages     = {140 -- 141},
  year      = {2010},
  language  = {en}
}
@inproceedings{ReisgenSchleserStieglitz2009,
  author    = {Reisgen, Uwe and Schleser, Markus and Stieglitz, Anja},
  title     = {Kleben im Schienenfahrzeugbau},
  series = {Die Verbindungs-Spezialisten 2009 : Große Schweißtechnische Tagung ; Forschungsforum, Industrieforum, Studentenkongress, Handwerkerforum ; Vortr{\"a}ge der Veranstaltung in Essen vom 14. bis 19. September 2009. DVS-Berichte. 258},
  booktitle = {Die Verbindungs-Spezialisten 2009 : Große Schweißtechnische Tagung ; Forschungsforum, Industrieforum, Studentenkongress, Handwerkerforum ; Vortr{\"a}ge der Veranstaltung in Essen vom 14. bis 19. September 2009. DVS-Berichte. 258},
  publisher = {DVS-Media},
  address   = {D{\"u}sseldorf},
  organization    = {DVS - Deutscher Verband f{\"u}r Schweißen und Verwandte Verfahren e.V. ; Große Schweißtechnische Tagung <2009, Essen>},
  isbn      = {978-3-87155-584-8},
  pages     = {182 -- 186},
  year      = {2009},
  language  = {de}
}
@inproceedings{ReisgenSchleserEssersetal.2012,
  author    = {Reisgen, Uwe and Schleser, Markus and Essers, Marc and Thiele, Regina and Schiebahn, Alexander},
  title     = {Klebstofffixiertes R{\"u}hrreibschweißen von d{\"u}nnen Aluminiumblechen},
  series = {DVS Congress 2012 : Große Schweißtechnische Tagung, DVS-Studentenkongress ; Vortr{\"a}ge der Veranstaltungen in Saarbr{\"u}cken am 17. und 18. September 2012. (DVS-Berichte ; 286)},
  booktitle = {DVS Congress 2012 : Große Schweißtechnische Tagung, DVS-Studentenkongress ; Vortr{\"a}ge der Veranstaltungen in Saarbr{\"u}cken am 17. und 18. September 2012. (DVS-Berichte ; 286)},
  publisher = {DVS-Media},
  address   = {D{\"u}sseldorf},
  organization    = {Große Schweißtechnische Tagung <2012, Saarbr{\"u}cken> ; Deutscher Verband f{\"u}r Schweißen und Verwandte Verfahren},
  isbn      = {978-3-87155-593-0},
  pages     = {20 -- 25},
  year      = {2012},
  language  = {de}
}
@inproceedings{BagheriSchleupenDahmannetal.2016,
  author    = {Bagheri, Mohsen and Schleupen, Josef and Dahmann, Peter and Kallweit, Stephan},
  title     = {Kletternde Wartungsplattform f{\"u}r die wetterunabh{\"a}ngige Instandhaltung von Rotorbl{\"a}ttern an Windenergieanlagen - SMART},
  series = {AKIDA 2016 Aachener Kolloquium f{\"u}r Instandhaltung, Diagnose und Anlagen{\"u}berwachung (AKIDA) am 15. und 16.11.2016, Technologiezentrum Aachen},
  booktitle = {AKIDA 2016 Aachener Kolloquium f{\"u}r Instandhaltung, Diagnose und Anlagen{\"u}berwachung (AKIDA) am 15. und 16.11.2016, Technologiezentrum Aachen},
  pages     = {21 Folien},
  year      = {2016},
  abstract  = {In Deutschland liegt der Anteil der Windkraft an der Gesamtstromerzeugung bei 13,3\% mit mehr als 25.000 installierten Windenergieanlagen (WEA). Weltweit erf{\"a}hrt die Windbranche ein rasantes Wachstum. Indien und China berichten eine j{\"a}hrliche Wachstumsrate an Neuinstallationen von 45\%. Die Technologie zur Erzeugung elektrischer Energie aus Windkraft ist noch vergleichsweise jung. Durch die weltweit steigende Anzahl an Windenergieanlagen w{\"a}chst zunehmend der Bedarf an innovativen Wartungsl{\"o}sungen. Komponenten wie Generator oder Getriebe sind inzwischen weitestgehend ausgereift. Der Fokus richtet sich zunehmend auf die wesentliche Kernkomponente - die Rotorbl{\"a}tter. Industriekletterer inspizieren die Rotorbl{\"a}tter oder T{\"u}rme i.d.R. in einem zwei Jahres Rhythmus. Sie werden zunehmend durch Seilarbeitsb{\"u}hnen unterst{\"u}tzt. F{\"u}r gr{\"o}ßere Reparaturen kommen Kr{\"a}ne zum Einsatz, mit denen das Rotorblatt f{\"u}r die Instandhaltung demontiert wird. Die Standardinspektion besteht aus Sicht- und Klopfpr{\"u}fung der Rotorblattoberfl{\"a}che und ist nur bei sehr ruhiger Wetterlage durchf{\"u}hrbar. Seit September 2014 wird das Forschungsprojekt SMART (Scanning, Monitoring, Analysis, Repair and Transportation), Entwicklung einer Wartungsplattform f{\"u}r WEA, vom BMWi gef{\"o}rdert. Das Konsortium besteht aus zwei Firmen und der Fachhochschule Aachen. Die SMART-Anlage klettert reibschl{\"u}ssig am Turm der WEA mittels speziellen Kettenfahrwerken (Abbildung) auf- und abw{\"a}rts. Ein ringf{\"o}rmiges Spannsystems, basierend auf dem Konzept der „N{\"u}rnberger"-Schere, erzeugt die erforderliche Anpresskraft f{\"u}r den Kletterprozess. Wettergesch{\"u}tzte Arbeitskabinen erm{\"o}glichen die ganzj{\"a}hrige Instandhaltung von Rotorbl{\"a}ttern und ebenso T{\"u}rmen. Dadurch k{\"o}nnen Wartungsarbeiten auf 24 Stunden am Tag ausgeweitet werden. Der kombinierte Einsatz (Sensorfusion) bildgebender Messtechnik wie Thermografie, Ultraschall, und Terahertz in der Arbeitskabine kann die Dokumentation, Effizienz und Qualit{\"a}t der Instandhaltungsarbeiten erheblich verbessern. Langfristiges Ziel von SMART ist ein Condition Monitoring f{\"u}r Rotorbl{\"a}tter und T{\"u}rme auf Basis digitalisierter dreidimensionaler Volumenscans. Der kooperative Einsatz mit UAVs erweitert die Instandhaltungsstrategie. UAVs erm{\"o}glichen die schnelle, kosteng{\"u}nstige globale optische Inspektion von Rotorblattoberfl{\"a}chen zur Detektion potentieller Fehlstellen. Der „Proof-of-Concept" Meilenstein wurde mit der Demonstration eines funktionsf{\"a}higen Modells im Dezember 2015 erfolgreich abgeschlossen.},
  language  = {de}
}
@inproceedings{PisarczykRitzSachtleben2013,
  author    = {Pisarczyk, Rafael and Ritz, Thomas and Sachtleben, Johanna},
  title     = {KMU-taugliche Modelle zur Entwicklung gebrauchstauglicher mobiler Unternehmenssoftware},
  series = {Mensch \& Computer 2013 - Workshopband : 13. fach{\"u}bergreifende Konferenz f{\"u}r interaktive und kooperative Medien},
  booktitle = {Mensch \& Computer 2013 - Workshopband : 13. fach{\"u}bergreifende Konferenz f{\"u}r interaktive und kooperative Medien},
  editor    = {Boll-Westermann, Susanne},
  publisher = {Oldenbourg},
  address   = {M{\"u}nchen},
  isbn      = {978-3-486-77855-7 (Print)},
  doi       = {10.1524/9783486781236},
  pages     = {29 -- 38},
  year      = {2013},
  language  = {de}
}
@inproceedings{StaatSzelinskiHeitzer2001,
  author    = {Staat, Manfred and Szelinski, E. and Heitzer, Michael},
  title     = {Kollapsanalyse von l{\"a}ngsfehlerbehafteten Rohren und Beh{\"a}ltern},
  year      = {2001},
  abstract  = {Es werden verbesserte Kollapsanalysen von dickwandigen, mit axialen Oberfl{\"a}chenfehlern behafteten Rohren und Beh{\"a}ltern vorgeschlagen.},
  subject      = {Druckbeh{\"a}lter},
  language  = {de}
}
@inproceedings{Overkamp2009,
  author    = {Overkamp, Stefan},
  title     = {Kombination von Desktop GIS, Geodatenbank und Internet-GIS am Beispiel von Manifold System 8.0, PostgreSQL 8.3 und Adobe Flex},
  year      = {2009},
  abstract  = {Dipl.-Ing. Stefan Overkamp - GISWORKS GbR, Velbert. 11 S. (S. 7-17). Beitrag zum 2. Aachener Softwaretag in der Wasserwirtschaft <2, 2009, Aachen> Aus der Gliederung: 1 Geoinformationssysteme 2 Anforderungen an eine kommunale Geodateninfrastruktur (GDI) 3 Komponenten einer GDI 3.1 Geodatenmanagement 3.2 Geodatenhaltung 3.3 High-End-GIS 3.4 intraGIS 4 GISWORKS 5 Weiterf{\"u}hrende Informationen},
  subject      = {Geoinformationssystem},
  language  = {de}
}
@inproceedings{WernerMansourRateikeetal.2011,
  author    = {Werner, Frederik and Mansour, Ahmed and Rateike, Franz-Matthias and Schusser, Sebastian and Wagner, Torsten and Yoshinobu, Tatsuo and Keusgen, Michael and Sch{\"o}ning, Michael Josef},
  title     = {Kompakter Aufbau eines lichtadressierbaren potentiometrischen Sensors mit verfahrbarem Diodenlaser},
  series = {10. Dresdner Sensor-Symposium : Dresden, 5. - 7. Dezember 2011 ; miniaturisierte analytische Verfahren, Hochtemperatur-Sensoren, Sensoren f{\"u}r Bioprozess- und Verfahrenstechnik, Sensoren f{\"u}r die Medizin, Chemische Verfahrenstechnik, Lebensmittelanalytik, innovative Sensorl{\"o}sungen, Sensoren f{\"u}r die Wasserqualit{\"a}t, Selbst{\"u}berwachung / Gerald Gerlach ... (Hg.) Dresdner Beitr{\"a}ge zur Sensorik. 43},
  booktitle = {10. Dresdner Sensor-Symposium : Dresden, 5. - 7. Dezember 2011 ; miniaturisierte analytische Verfahren, Hochtemperatur-Sensoren, Sensoren f{\"u}r Bioprozess- und Verfahrenstechnik, Sensoren f{\"u}r die Medizin, Chemische Verfahrenstechnik, Lebensmittelanalytik, innovative Sensorl{\"o}sungen, Sensoren f{\"u}r die Wasserqualit{\"a}t, Selbst{\"u}berwachung / Gerald Gerlach ... (Hg.) Dresdner Beitr{\"a}ge zur Sensorik. 43},
  editor    = {Gerlach, Gerald},
  publisher = {TUDpress},
  address   = {Dresden},
  isbn      = {978-3-942710-53-4},
  pages     = {277 -- 280},
  year      = {2011},
  language  = {de}
}
@inproceedings{BudaWollert2008,
  author    = {Buda, Aurel and Wollert, J{\"o}rg},
  title     = {Kompensation von Fading und Koexistenzproblemen in IEEE 802.15.4 Netzwerken durch Diversit{\"a}t : die Kombination macht's m{\"o}glich},
  series = {Automation 2008: L{\"o}sungen f{\"u}r die Zukunft ; der Automatisierungskongress in Deutschland ; Tagung Baden-Baden, 3. und 4. Juni 2008. (VDI-Berichte ; 2032)},
  booktitle = {Automation 2008: L{\"o}sungen f{\"u}r die Zukunft ; der Automatisierungskongress in Deutschland ; Tagung Baden-Baden, 3. und 4. Juni 2008. (VDI-Berichte ; 2032)},
  publisher = {VDI-Verl.},
  address   = {D{\"u}sseldorf},
  organization    = {Automatisierungskongress <2008, Baden-Baden>},
  isbn      = {978-3-18-092032-0},
  pages     = {139 -- 142},
  year      = {2008},
  language  = {de}
}
@inproceedings{BillerbeckLadwigSaldenetal.2015,
  author    = {Billerbeck, Katrin and Ladwig, Tina and Salden, Peter and Barnat, Miriam},
  title     = {Kompetenzen visualisieren als Notenersatz? Ann{\"a}herung an eine didaktische Herausforderung},
  series = {Wie viel (Grundlagen) Wissen braucht technische Bildung? : Wege zu technischer Bildung : Referate der 9. Ingenieurp{\"a}dagogischen Regionaltagung 2014 an der Universit{\"a}t Siegen, 6.-8. November 2014},
  booktitle = {Wie viel (Grundlagen) Wissen braucht technische Bildung? : Wege zu technischer Bildung : Referate der 9. Ingenieurp{\"a}dagogischen Regionaltagung 2014 an der Universit{\"a}t Siegen, 6.-8. November 2014},
  editor    = {Kammasch, Gudrun},
  publisher = {Berlin},
  address   = {IPW},
  isbn      = {978-3-00-049835-0},
  pages     = {57 -- 63},
  year      = {2015},
  language  = {de}
}
@inproceedings{ReisgenSchleserHarmsetal.2010,
  author    = {Reisgen, Uwe and Schleser, Markus and Harms, Alexander and Schiebahn, Alexander},
  title     = {Konduktiv unterst{\"u}tztes R{\"u}hrreibschweißen an Stahl- und Aluminiumwerkstoffen},
  series = {DVS congress 2010 : Große Schweißtechnische Tagung ; Studentenkongress ; Statusseminar "Schneidtechnik" ; Abschlusskolloquium zum AiF-Forschungscluster "Integration des R{\"u}hrreibschweißens in Fertigungsprozessketten" ; Vortr{\"a}ge der Veranstaltung in N{\"u}rnberg am 27. und 28. September 2010. (DVS-Berichte ; 267)},
  booktitle = {DVS congress 2010 : Große Schweißtechnische Tagung ; Studentenkongress ; Statusseminar "Schneidtechnik" ; Abschlusskolloquium zum AiF-Forschungscluster "Integration des R{\"u}hrreibschweißens in Fertigungsprozessketten" ; Vortr{\"a}ge der Veranstaltung in N{\"u}rnberg am 27. und 28. September 2010. (DVS-Berichte ; 267)},
  publisher = {DVS Media},
  address   = {D{\"u}sseldorf},
  organization    = {Deutscher Verband f{\"u}r Schweißen und Verwandte Verfahren ; Große Schweißtechnische Tagung <2010, N{\"u}rnberg>},
  isbn      = {978-3-87155-592-3},
  pages     = {394 -- 398},
  year      = {2010},
  language  = {de}
}
@inproceedings{SchuermannKellerWollert2009,
  author    = {Sch{\"u}rmann, Volker and Keller, Alex and Wollert, J{\"o}rg},
  title     = {Konvergenz von drahtlosen und drahtgebundenen Kommunikationstechnologien in der Geb{\"a}udeautomation},
  series = {Wireless technologies : von der Technologie zur Anwendung ; 11. Kongress, 29. - 30. September 2009, Stuttgart / [11. Wireless-Technologies-Kongress]. (Fortschritt-Berichte VDI : Reihe 10, Informatik, Kommunikation ; Nr. 800)},
  booktitle = {Wireless technologies : von der Technologie zur Anwendung ; 11. Kongress, 29. - 30. September 2009, Stuttgart / [11. Wireless-Technologies-Kongress]. (Fortschritt-Berichte VDI : Reihe 10, Informatik, Kommunikation ; Nr. 800)},
  publisher = {VDI-Verl.},
  address   = {D{\"u}sseldorf},
  organization    = {Wireless-Technologies-Kongress <11, 2009, Stuttgart>},
  isbn      = {978-3-18-380010-0},
  pages     = {197 -- 205},
  year      = {2009},
  language  = {de}
}
@inproceedings{MollKoehlerWolf2019,
  author    = {Moll, Florian and K{\"o}hler, Klemens and Wolf, Martin},
  title     = {Konzeption von IT-Sicherheitsl{\"o}sungen unter ethischen Gesichtspunkten am Beispiel einer Monitoring-App f{\"u}r mobile Endger{\"a}te},
  series = {Angewandte Forschung in der Wirtschaftsinformatik 2019 : Tagungsband zur 32. AKWI-Jahrestagung},
  booktitle = {Angewandte Forschung in der Wirtschaftsinformatik 2019 : Tagungsband zur 32. AKWI-Jahrestagung},
  publisher = {mana-Buch},
  address   = {Heide},
  isbn      = {978-3-944330-62-4},
  pages     = {61 -- 72},
  year      = {2019},
  abstract  = {Die steigende Popularit{\"a}t von mobilen Endger{\"a}ten im privaten und gesch{\"a}ftlichen Umfeld geht mit einem Anstieg an Sicherheitsl{\"u}cken und somit potentiellen Angriffsfl{\"a}chen einher. Als ein Element der technischen und organisatorischen Maßnahmen zum Schutz eines Netzwerkes k{\"o}nnen Monitoring-Apps dienen, die unerw{\"u}nschtes Verhalten und Angriffe erkennen. Die automatisierte {\"U}berwachung von Endger{\"a}ten ist jedoch rechtlich und ethisch komplex. Dies in Kombination mit einer hohen Sensibilit{\"a}t der Nutzer und Nutzerinnen dieser Ger{\"a}te in Bezug auf Privatsph{\"a}re, kann zu einer geringen Akzeptanz und Compliance f{\"u}hren. Eine datenschutzrechtlich und ethisch einwandfreie Konzeption solcher Apps bereits im Designprozess f{\"u}hrt zu h{\"o}herer Akzeptanz und verbessert so die Effizienz. Diese Analyse beschreibt M{\"o}glichkeiten zur Umsetzung.},
  language  = {de}
}
@inproceedings{Hoffschmidt2011,
  author    = {Hoffschmidt, Bernhard},
  title     = {Kooperationen und Ziele am Standort J{\"u}lich},
  series = {Forschung und Entwicklung f{\"u}r solarthermische Kraftwerke : 14. K{\"o}lner Sonnenkolloquium Mittwoch, 13. Juli 2011, im Auditorium des Campus J{\"u}lich der FH Aachen : Kurzfassungen der Vortr{\"a}ge und Poster},
  booktitle = {Forschung und Entwicklung f{\"u}r solarthermische Kraftwerke : 14. K{\"o}lner Sonnenkolloquium Mittwoch, 13. Juli 2011, im Auditorium des Campus J{\"u}lich der FH Aachen : Kurzfassungen der Vortr{\"a}ge und Poster},
  publisher = {DLR},
  address   = {K{\"o}ln},
  pages     = {4 S.},
  year      = {2011},
  language  = {de}
}
@inproceedings{RitzFuchs2008,
  author    = {Ritz, Thomas and Fuchs, Britta},
  title     = {Kosten-Nutzen-Bewertungen bei mobilen Anwendungen},
  series = {Mobile und Ubiquit{\"a}re Informationssysteme - Technologien, Prozesse, Marktfahigkeit. Proceedings zur 3. Konferenz Mobile und Ubiquit{\"a}re Informationssysteme (MMS 2008) 26. - 28. Februar 2008, M{\"u}nchen, Germany. - (GI-Edition : Proceedings ; 123) Breitner, Michael H. [Hrsg.]},
  booktitle = {Mobile und Ubiquit{\"a}re Informationssysteme - Technologien, Prozesse, Marktfahigkeit. Proceedings zur 3. Konferenz Mobile und Ubiquit{\"a}re Informationssysteme (MMS 2008) 26. - 28. Februar 2008, M{\"u}nchen, Germany. - (GI-Edition : Proceedings ; 123) Breitner, Michael H. [Hrsg.]},
  editor    = {Breitner, Michael},
  publisher = {Ges. f{\"u}r Informatik},
  address   = {Bonn},
  isbn      = {978-3-88579-217-8},
  pages     = {164 -- 177},
  year      = {2008},
  language  = {de}
}
@inproceedings{IlleSchrammAdametal.2009,
  author    = {Ille, Fabian and Schramm, S. and Adam, M. and Backes, K. and Anthrakidis, Anette and Faber, Christian},
  title     = {Kraft-W{\"a}rme-K{\"a}lte-Kopplung im Leistungsbereich in 10kW mit periodisch arbeitender Sorptionsmaschine},
  series = {DKV-Tagungsbericht. 35,2,1. Deutsche K{\"a}lte-Klima-Tagung 2008 Ulm},
  booktitle = {DKV-Tagungsbericht. 35,2,1. Deutsche K{\"a}lte-Klima-Tagung 2008 Ulm},
  publisher = {Dt. K{\"a}lte- und Klimatechnischer Verein},
  address   = {Hannover},
  isbn      = {978-3-932715-44-0},
  pages     = {305 -- 320},
  year      = {2009},
  language  = {de}
}
@inproceedings{SchneckenburgerFranzenGligorevicetal.2011,
  author    = {Schneckenburger, N. and Franzen, N. and Gligorevic, Snjezana and Schnell, M.},
  title     = {L-band compatibility of LDACS1},
  series = {IEEE/AIAA 30th Digital Avionics Systems Conference (DASC) : 16 - 20 Oct. 2011, Seattle, Wash.},
  booktitle = {IEEE/AIAA 30th Digital Avionics Systems Conference (DASC) : 16 - 20 Oct. 2011, Seattle, Wash.},
  organization    = {Institute of Electrical and Electronics Engineers},
  isbn      = {978-1-61284-797-9},
  issn      = {2155-7195},
  pages     = {4C3-1 -- 4C3-11},
  year      = {2011},
  language  = {en}
}
@inproceedings{GligorevicSchneckenburgerFranzenetal.2011,
  author    = {Gligorevic, Snjezana and Schneckenburger, N. and Franzen, N. and Schnell, Michael and M{\"u}ller, S. and G{\"u}nzel, H.},
  title     = {L-Band compatibility of LDACS1},
  series = {3rd CEAS Air and Space Conference, 24 - 28 October 2011, Venezia, Italy},
  booktitle = {3rd CEAS Air and Space Conference, 24 - 28 October 2011, Venezia, Italy},
  organization    = {European Air and Space Conference <3, 2011, Venezia>},
  pages     = {1 -- 8},
  year      = {2011},
  language  = {en}
}
@inproceedings{SchnellFranzenGligorevic2010,
  author    = {Schnell, Michael and Franzen, Nico and Gligorevic, Snjezana},
  title     = {L-DACS1 laboratory demonstrator development and compatibility measurement set-up},
  series = {IEEE/AIAA 29th Digital Avionics Systems Conference (DASC) : 3 - 7 Oct. 2010, Salt Lake City, Utah},
  booktitle = {IEEE/AIAA 29th Digital Avionics Systems Conference (DASC) : 3 - 7 Oct. 2010, Salt Lake City, Utah},
  organization    = {Institute of Electrical and Electronics Engineers},
  isbn      = {9781424466160 ; 9781424466184},
  pages     = {3E3-1 -- 3E3-11},
  year      = {2010},
  language  = {en}
}
@inproceedings{PoghossianBronderSchejaetal.2016,
  author    = {Poghossian, Arshak and Bronder, Thomas and Scheja, S. and Wu, Chunsheng and Metzger-Boddien, C. and Keusgen, M. and Sch{\"o}ning, Michael Josef},
  title     = {Label-free Electrostatic Detection of DNA Amplification by PCR Using Capacitive Field-effect Devices},
  series = {Procedia Engineering},
  volume    = {Vol. 168},
  booktitle = {Procedia Engineering},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {1877-7058},
  doi       = {10.1016/j.proeng.2016.11.512},
  pages     = {514 -- 517},
  year      = {2016},
  abstract  = {A capacitive field-effect EIS (electrolyte-insulator-semiconductor) sensor modified with a positively charged weak polyelectrolyte of poly(allylamine hydrochloride) (PAH)/single-stranded probe DNA (ssDNA) bilayer has been used for a label-free electrostatic detection of pathogen-specific DNA amplification via polymerase chain reaction (PCR). The sensor is able to distinguish between positive and negative PCR solutions, to detect the existence of target DNA amplicons in PCR samples and thus, can be used as tool for a quick verification of DNA amplification and the successful PCR process.},
  language  = {en}
}
@inproceedings{PoghossianBronderWuetal.2015,
  author    = {Poghossian, Arshak and Bronder, Thomas and Wu, Chunsheng and Sch{\"o}ning, Michael Josef},
  title     = {Label-free sensing of biomolecules by their intrinsic molecular charge using field-effect devices},
  series = {Semiconductor Micro- and Nanoelectonics : Proceedings of the tenth international conference, Yerevan, Armenia, September 11-13},
  booktitle = {Semiconductor Micro- and Nanoelectonics : Proceedings of the tenth international conference, Yerevan, Armenia, September 11-13},
  isbn      = {978-5-8084-1991-9},
  pages     = {61 -- 63},
  year      = {2015},
  language  = {en}
}
@inproceedings{ZischankHeidlerKernetal.2002,
  author    = {Zischank, Wolfgang J. and Heidler, Fridolin and Kern, Alexander and Metwally, I. A. and Wiesinger, J. and Seevers, M.},
  title     = {Laboratory simulation of direct lightning strokes to a modelled building - measurement of magnetic fields and induced voltages},
  year      = {2002},
  abstract  = {In IEC 61312-2 equations for the assessment of the magnetic fields inside structures due to a direct lightning strike are given. These equations are based on computer simulations for shields consisting of a single-layer steel grid of a given mesh width. Real constructions, however, contain at least two layers of reinforcement steel grids. The objective of this study was to experimentally determine the additional shielding effectiveness of a second reinforcement layer compared to a single-layer grid. To this end, simulated structures were set up in the high current laboratory. The structures consisted of cubic cages of 2 m side length with one or with two reinforcement grids, respectively. The structures were exposed to direct lightning currents representing the variety of anticipated lightning current waveforms. The magnetic fields and their derivatives at several positions inside the structure as well as the voltage between "floor" and "roof" in the center were determined for different current injection points. From these data the improvement of the shielding caused by a second reinforcement layer is derived.},
  language  = {en}
}
@inproceedings{Hartz2004,
  author    = {Hartz, Thomas},
  title     = {LACASA - ein Instrument zur energetischen Analyse und Optimierung von Geb{\"a}uden mit Anlagentechnik},
  series = {14. Symposium Thermische Solarenergie : 12. bis 14. Mai 2004, Kloster Banz, Bad Staffelstein / OTTI-Kolleg Technik, Energie, Management},
  booktitle = {14. Symposium Thermische Solarenergie : 12. bis 14. Mai 2004, Kloster Banz, Bad Staffelstein / OTTI-Kolleg Technik, Energie, Management},
  publisher = {OTTI-Energie-Kolleg},
  address   = {Regensburg},
  pages     = {402 -- 406},
  year      = {2004},
  language  = {de}
}
@inproceedings{Mertens2000,
  author    = {Mertens, Josef},
  title     = {Laminar leading edges: manufacturing, contamination, and operational aspects - results from the German RaWid programme},
  year      = {2000},
  abstract  = {RaWid was the German national technology programme on transonic aerodynamics and supporting technologies, lasting from 1995 to 1998. One of the main topics was laminar wing development. Besides aerodynamic design work, many operational aspects were investigated. A manufacturing concept was developed to be applied to operational laminar wings and empennages. It was built in a large scale manufacturing demonstrator with the aerodynamic shape of a 1,5 m section of the A320 fin nose. Tolerances in shape and roughness fulfilled all requirements. The construction can easily be adapted to varying stiffness and strength requirements. Weight and manufacturing costs are comparable to common nose designs. The mock-up to be designed in ALTTA is based on this manufacturing principle. Another critical point is contamination of suction surfaces. Several tests were performed to investigate perforated titanium suction surfaces at realistic operational conditions: - a one year flight test with a suction plate in the stagnation area of the Airbus "Beluga" - a one year test of several suction plates in a ground test near the airport - a one year test of a working suction ground test installation at all weather conditions. No critical results were found. There is no long term suction degradation visible. Icing conditions and ground de-icing fluids used on airports did not pose severe problems. Some problems detected require only respection of weak design constraints.},
  subject      = {Laminare Str{\"o}mung},
  language  = {en}
}
@inproceedings{Wollert2006,
  author    = {Wollert, J{\"o}rg},
  title     = {Langzeitstatistische Untersuchungen zur Qualit{\"a}t von Funkkan{\"a}len f{\"u}r das industrielle Umfeld},
  series = {Wireless technologies : von der Technologie zur Anwendung : 8. Kongress, 27. - 28. September 2006, Dortmund ( J{\"o}rg Wollert (Hrsg.) (Fortschritt-Berichte VDI : Reihe 10, Informatik, Kommunikation ; Nr. 772)},
  booktitle = {Wireless technologies : von der Technologie zur Anwendung : 8. Kongress, 27. - 28. September 2006, Dortmund ( J{\"o}rg Wollert (Hrsg.) (Fortschritt-Berichte VDI : Reihe 10, Informatik, Kommunikation ; Nr. 772)},
  publisher = {VDI-Verl.},
  address   = {D{\"u}sseldorf},
  isbn      = {3-18-377210-8},
  pages     = {165 -- 176},
  year      = {2006},
  language  = {de}
}
@inproceedings{SeefeldtBauerDachwaldetal.2015,
  author    = {Seefeldt, Patric and Bauer, Waldemar and Dachwald, Bernd and Grundmann, Jan Thimo and Straubel, Marco and Sznajder, Maciej and T{\´o}th, Norbert and Zander, Martin E.},
  title     = {Large lightweight deployable structures for planetary defence: solar sail propulsion, solar concentrator payloads, large-scale photovoltaic power},
  series = {4th IAA Planetary Defense Conference - PDC 2015, 13-17 April 2015, Frascati, Roma, Italy},
  booktitle = {4th IAA Planetary Defense Conference - PDC 2015, 13-17 April 2015, Frascati, Roma, Italy},
  pages     = {24},
  year      = {2015},
  language  = {en}
}