@article{HagenkampBlankeDoering2021,
  author    = {Hagenkamp, Markus and Blanke, Tobias and D{\"o}ring, Bernd},
  title     = {Thermoelectric building temperature control: a potential assessment},
  series = {International Journal of Energy and Environmental Engineering},
  volume    = {13},
  journal   = {International Journal of Energy and Environmental Engineering},
  publisher = {Springer},
  address   = {Berlin},
  doi       = {10.1007/s40095-021-00424-x},
  pages     = {241 -- 254},
  year      = {2021},
  abstract  = {This study focuses on thermoelectric elements (TEE) as an alternative for room temperature control. TEE are semi-conductor devices that can provide heating and cooling via a heat pump effect without direct noise emissions and no refrigerant use. An efficiency evaluation of the optimal operating mode is carried out for different numbers of TEE, ambient temperatures, and heating loads. The influence of an additional heat recovery unit on system efficiency and an unevenly distributed heating demand are examined. The results show that TEE can provide heat at a coefficient of performance (COP) greater than one especially for small heating demands and high ambient temperatures. The efficiency increases with the number of elements in the system and is subject to economies of scale. The best COP exceeds six at optimal operating conditions. An additional heat recovery unit proves beneficial for low ambient temperatures and systems with few TEE. It makes COPs above one possible at ambient temperatures below 0 ∘C. The effect increases efficiency by maximal 0.81 (from 1.90 to 2.71) at ambient temperature 5 K below room temperature and heating demand Q˙h=100W but is subject to diseconomies of scale. Thermoelectric technology is a valuable option for electricity-based heat supply and can provide cooling and ventilation functions. A careful system design as well as an additional heat recovery unit significantly benefits the performance. This makes TEE superior to direct current heating systems and competitive to heat pumps for small scale applications with focus on avoiding noise and harmful refrigerants.},
  language  = {en}
}
@article{KaemperPicardBrilletal.2003,
  author    = {K{\"a}mper, Klaus-Peter and Picard, Antoni and Brill, Manfred and Cassel, Detlev and Jentsch, Andreas and Merten, Sabine and Rollwa, Markus},
  title     = {The Virtual Clean Room - a new tool in teaching MST process technologies},
  year      = {2003},
  abstract  = {The Virtual Clean Room - a new tool in teaching MST process technologies University education in high-technology fields like MST is not complete without intensive laboratory sessions. Students cannot fully grasp the complexity and the special problems related to the manufacturing of microsystems without a thorough hands-on experience in a MST clean room.},
  subject      = {Virtuelle Maschine},
  language  = {en}
}
@article{ZhubanovaDigelNojimaetal.2007,
  author    = {Zhubanova, Azhar A. and Digel, Ilya and Nojima, H. and Artmann, Gerhard},
  title     = {The use of bactericidal effects of cluster ions generated by plasma in medical biotechnology},
  year      = {2007},
  abstract  = {The most of conventional methods of air purification use the power of a fan to draw in air and pass it through a filter. The problem of bacterial contamination of inner parts of such a type of air conditioners in some cases draws attention towards alternative air-cleaning systems. Some manufacturers offer to use the ozone's bactericidal and deodorizing effects, but the wide spreading of such systems is restricted by the fact that toxic effects of ozone in respect of human beings are well known. In 2000 Sharp Inc. introduced "Plasma Cluster Ions (PCI)" air purification technology, which uses plasma discharge to generate cluster ions (I 0-14 ). This technology has been developed for those customers that are conscious about health and hygiene. In our experiments, we focused on some principal aspects of plasma-generated ions application - time-dependency and irreversibility of bactericidal action, spatial and kinetic characteristics of emitted cluster particles, their chemical targets in the microbial cells.},
  subject      = {Clusterion},
  language  = {en}
}
@article{MatheisRoethWagner2005,
  author    = {Matheis, Anton and R{\"o}th, Thilo and Wagner, Manfred},
  title     = {Studentenprojekt "Capro" - eine virtuelle Sportwagenstudie "Vision 2015"},
  year      = {2005},
  abstract  = {Design- und Karosseriebaustudenten der FH Aachen entwickeln gemeinsam mit externen Fachleuten unter Einsatz virtueller Entwicklungswerkzeuge ein Konzept f{\"u}r einen Sportwagen},
  subject      = {Karosseriebau},
  language  = {de}
}
@article{JildehWagnerSchoening2021,
  author    = {Jildeh, Zaid B. and Wagner, Patrick H. and Sch{\"o}ning, Michael Josef},
  title     = {Sterilization of Objects, Products, and Packaging Surfaces and Their Characterization in Different Fields of Industry: The Status in 2020},
  series = {physica status solidi (a) applications and materials science},
  volume    = {218},
  journal   = {physica status solidi (a) applications and materials science},
  number    = {13},
  publisher = {Wiley-VCH},
  address   = {Weinheim},
  issn      = {1862-6319},
  doi       = {10.1002/pssa.202000732},
  pages     = {27 Seiten},
  year      = {2021},
  abstract  = {The treatment method to deactivate viable microorganisms from objects or products is termed sterilization. There are multiple forms of sterilization, each intended to be applied for a specific target, which depends on—but not limited to—the thermal, physical, and chemical stability of that target. Herein, an overview on the currently used sterilization processes in the global market is provided. Different sterilization techniques are grouped under a category that describes the method of treatment: radiation (gamma, electron beam, X-ray, and ultraviolet), thermal (dry and moist heat), and chemical (ethylene oxide, ozone, chlorine dioxide, and hydrogen peroxide). For each sterilization process, the typical process parameters as defined by regulations and the mode of antimicrobial activity are summarized. Finally, the recommended microorganisms that are used as biological indicators to validate sterilization processes in accordance with the rules that are established by various regulatory agencies are summarized.},
  language  = {en}
}
@article{EggertKreuzer2022,
  author    = {Eggert, Mathias and Kreuzer, Vincent},
  title     = {Sprachsteuerung im Gesundheitswesen - Anforderungen und Auswahl geeigneter Anbieter},
  series = {HMD Praxis der Wirtschaftsinformatik},
  volume    = {59},
  journal   = {HMD Praxis der Wirtschaftsinformatik},
  publisher = {Springer Vieweg},
  address   = {Wiesbaden},
  isbn      = {2198-2775},
  issn      = {1436-3011},
  doi       = {10.1365/s40702-022-00919-z},
  pages     = {1640 -- 1652},
  year      = {2022},
  abstract  = {Das Gesundheitswesen ist konfrontiert mit steigenden Kosten und einer immer schwieriger werdenden Personalsituation. Zeitgleich versprechen moderne Sprachsteuerungssysteme Prozesse in Arztpraxen und Krankenh{\"a}usern zu verschlanken und Vorg{\"a}nge zu beschleunigen. Dennoch wird derzeit der Einsatz von Sprachsteuerungssystemen in Arztpraxen oder Krankenh{\"a}usern nur selten beobachtet, was auch an den besonders strengen Datenschutzauflagen der Datenschutzgrundverordnung (DSGVO) liegt. Dar{\"u}ber hinaus wirft die niedrige Nutzungsrate die Frage nach den konkreten Anforderungen und ihrer Umsetzbarkeit auf, was durch den vorliegenden Beitrag adressiert wird, indem die Ergebnisse von Interviews mit acht medizinischen Fachexperten ausgewertet werden. Erg{\"a}nzend wird die technische Umsetzbarkeit einzelner Anforderungen mit unterschiedlichen Cloud-Anbietern erprobt.},
  language  = {de}
}
@article{BornheimGriegerBlanecketal.2024,
  author    = {Bornheim, Tobias and Grieger, Niklas and Blaneck, Patrick Gustav and Bialonski, Stephan},
  title     = {Speaker Attribution in German Parliamentary Debates with QLoRA-adapted Large Language Models},
  series = {Journal for language technology and computational linguistics : JLCL},
  volume    = {37},
  journal   = {Journal for language technology and computational linguistics : JLCL},
  number    = {1},
  publisher = {Gesellschaft f{\"u}r Sprachtechnologie und Computerlinguistik},
  address   = {Regensburg},
  issn      = {2190-6858},
  doi       = {10.21248/jlcl.37.2024.244},
  pages     = {13 Seiten},
  year      = {2024},
  abstract  = {The growing body of political texts opens up new opportunities for rich insights into political dynamics and ideologies but also increases the workload for manual analysis. Automated speaker attribution, which detects who said what to whom in a speech event and is closely related to semantic role labeling, is an important processing step for computational text analysis. We study the potential of the large language model family Llama 2 to automate speaker attribution in German parliamentary debates from 2017-2021. We fine-tune Llama 2 with QLoRA, an efficient training strategy, and observe our approach to achieve competitive performance in the GermEval 2023 Shared Task On Speaker Attribution in German News Articles and Parliamentary Debates. Our results shed light on the capabilities of large language models in automating speaker attribution, revealing a promising avenue for computational analysis of political discourse and the development of semantic role labeling systems.},
  language  = {en}
}
@article{Staat2003,
  author    = {Staat, Manfred},
  title     = {Shakedown and ratchetting under tension-torsion loadings: analysis and experiments},
  year      = {2003},
  abstract  = {Structural design analyses are conducted with the aim of verifying the exclusion of ratchetting. To this end it is important to make a clear distinction between the shakedown range and the ratchetting range. The performed experiment comprised a hollow tension specimen which was subjected to alternating axial forces, superimposed with constant moments. First, a series of uniaxial tests has been carried out in order to calibrate a bounded kinematic hardening rule. The load parameters have been selected on the basis of previous shakedown analyses with the PERMAS code using a kinematic hardening material model. It is shown that this shakedown analysis gives reasonable agreement between the experimental and the numerical results. A linear and a nonlinear kinematic hardening model of two-surface plasticity are compared in material shakedown analysis.},
  subject      = {Einspielen <Werkstoff>},
  language  = {en}
}
@article{Lohr1996,
  author    = {Lohr, J{\"u}rgen},
  title     = {Server f{\"u}r den interaktiven Einsatz},
  year      = {1996},
  abstract  = {J{\"u}rgen Lohr, Jahrgang 1962, besch{\"a}ftigt mit Softwareentwicklung im Projekt "Interaktive Multimedia" bei Telekom AG, Entwicklungszentrum Berlin. Zuerst erschienen in: Telekom-Praxis Ausgabe 1996. Inhaltsverzeichnis: 1. Einleitung 1.1 Einf{\"u}hrung 1.2 Neue Dienste und Anwendungen 2 Modell zur Verteilung und Architektur 3 Technologien 3.1 Netzwerk 3.2 Computertechniken 3.3. Aufgaben der Server 4 Geplanter Einsatz der Pilotprojekte 4.1 Pilote der Telekom 4.2 Show-Case Berlin 5 Verwendete Server-Architektur 5.1 Berlin - SEL/Alcatel 5.2 Hanburg - Philips 5.3. K{\"o}ln/Bonn - Digital, FUBA und Nokia 5.4 N{\"u}rnberg - Oracle, nCube und Sequent 5.5 Stuttgart - SEL/Alcatel, Hewlett Packard und Bosch 6 Zuk{\"u}nftige Aspekte 6.1 DVB 6.2 DAVIC 6.3 weitere Aspekte 7 Zusammenfassung 8 Schrifttum 9 verwendete Abk{\"u}rzungen},
  subject      = {Multimediamarkt},
  language  = {de}
}
@article{EggertMoulen2020,
  author    = {Eggert, Mathias and Moulen, Tobias},
  title     = {Selektion von Gesch{\"a}ftsprozessen zur Anwendung von Robotic Process Automation am Beispiel einer Versicherung},
  series = {HMD Praxis der Wirtschaftsinformatik},
  volume    = {57},
  journal   = {HMD Praxis der Wirtschaftsinformatik},
  number    = {6},
  publisher = {Springer},
  address   = {Weinheim},
  issn      = {1436-3011},
  doi       = {10.1365/s40702-020-00665-0},
  pages     = {1150 -- 1162},
  year      = {2020},
  abstract  = {H{\"a}ufig bremsen geringe IT-Ressourcen, fehlende Softwareschnittstellen oder eine veraltete und komplex gewachsene Systemlandschaft die Automatisierung von Gesch{\"a}ftsprozessen. Robotic Process Automation (RPA) ist eine vielversprechende Methode, um Gesch{\"a}ftsprozesse oberfl{\"a}chenbasiert und ohne gr{\"o}ßere Systemeingriffe zu automatisieren und Medienbr{\"u}che abzubauen. Die Auswahl der passenden Prozesse ist dabei f{\"u}r den Erfolg von RPA-Projekten entscheidend. Der vorliegende Beitrag liefert daf{\"u}r Selektionskriterien, die aus einer qualitativen Inhaltanalyse von elf Interviews mit RPA-Experten aus dem Versicherungsumfeld resultieren. Das Ergebnis umfasst eine gewichtetet Liste von sieben Dimensionen und 51 Prozesskriterien, welche die Automatisierung mit Softwarerobotern beg{\"u}nstigen bzw. deren Nichterf{\"u}llung eine Umsetzung erschweren oder sogar verhindern. Die drei wichtigsten Kriterien zur Auswahl von Gesch{\"a}ftsprozessen f{\"u}r die Automatisierung mittels RPA umfassen die Entlastung der an dem Prozess mitwirkenden Mitarbeiter (Arbeitnehmer{\"u}berlastung), die Ausf{\"u}hrbarkeit des Prozesses mittels Regeln (Regelbasierte Prozessteuerung) sowie ein positiver Kosten-Nutzen-Vergleich. Praktiker k{\"o}nnen diese Kriterien verwenden, um eine systematische Auswahl von RPA-relevanten Prozessen vorzunehmen. Aus wissenschaftlicher Perspektive stellen die Ergebnisse eine Grundlage zur Erkl{\"a}rung des Erfolgs und Misserfolgs von RPA-Projekten dar.},
  language  = {de}
}
@article{GebhardtBrueckerSchmidt2005,
  author    = {Gebhardt, Andreas and Br{\"u}cker, Christoph and Schmidt, Frank-Michael},
  title     = {RP gest{\"u}tzte Herstellung komplexer transparenter Hohlr{\"a}ume f{\"u}r die Str{\"o}mungsanalyse},
  year      = {2005},
  abstract  = {Die Berechnung der Durchstr{\"o}mung von Bauteilen ist gegen{\"u}ber derjenigen von umstr{\"o}mten Bauteilen deutlich im Hintertreffen. Das liegt vor allem an der fehlenden Verf{\"u}gbarkeit geeigneter optisch transparenter Modellkan{\"a}le f{\"u}r die experimentelle Analyse. Der Beitrag stellt ein Verfahren zur Herstellung transparenter durchstr{\"o}mter Geometrien auf der Basis generativ gefertigter Urmodelle vor. Damit k{\"o}nnen beliebig komplexe Innenstr{\"o}mungen optisch analysiert werden. Anhand von zwei Beispielen aus der Medizin, der Modellierung der oberen Atemwege und des Bronchialbaums, wird das Verfahren vorgef{\"u}hrt. Der generative Bauprozess mittels 3D-Printing wird beschrieben und die Abformung in transparentem Silikon gezeigt. Schließlich werden beispielhaft der Messaufbau und Ergebnisse der Anwendung vorgestellt. Das Verfahren bildet die Grundlage f{\"u}r die Analyse und Berechnung komplexer Innenstr{\"o}mungen und tr{\"a}gt somit zur Verbesserung zahlreicher technischer Anwendungen bei.},
  subject      = {Rapid prototyping},
  language  = {de}
}
@article{Kern2003,
  author    = {Kern, Alexander},
  title     = {Risikomanagement f{\"u}r den Blitzschutz - Absch{\"a}tzung des Blitzschadensrisikos nach der neuen Vornorm VDE V 0185 Teil 2 : 2002},
  year      = {2003},
  abstract  = {Ein vorausschauendes Risikomanagement beinhaltet, Risiken zu kalkulieren. Es liefert Entscheidungsgrundlagen, um diese Risiken zu begrenzen und es macht transparent,welche Risiken sinnvoll {\"u}ber Versicherungen abgedeckt werden sollten. Bei Unternehmen, die mit umfangreichen elektronischenEinrichtungen produzieren oder Dienstleistungen erbringen (und das sind heutzutage wohl die meisten), muss auch das Risiko durch Blitzeinwirkungen besondere Ber{\"u}cksichtigung finden. Dabei ist zu beachten, dass der Schaden aufgrund der Nichtverf{\"u}gbarkeit der elektronischen Einrichtungen und damit derProduktion bzw. der Dienstleistung und ggf. der Verlust von Daten den Hardwareschaden an der betroffenen Anlage oft bei weitem {\"u}bersteigt.},
  language  = {de}
}
@article{RoethenbacherCesariDoppleretal.2022,
  author    = {R{\"o}thenbacher, Annika and Cesari, Matteo and Doppler, Christopher E.J. and Okkels, Niels and Willemsen, Nele and Sembowski, Nora and Seger, Aline and Lindner, Marie and Brune, Corinna and Stefani, Ambra and H{\"o}gl, Birgit and Bialonski, Stephan and Borghammer, Per and Fink, Gereon R. and Schober, Martin and Sommerauer, Michael},
  title     = {RBDtector: an open-source software to detect REM sleep without atonia according to visual scoring criteria},
  series = {Scientific Reports},
  volume    = {12},
  journal   = {Scientific Reports},
  number    = {Article number: 20886},
  publisher = {Springer Nature},
  address   = {London},
  issn      = {2045-2322},
  doi       = {10.1038/s41598-022-25163-9},
  pages     = {1 -- 14},
  year      = {2022},
  abstract  = {REM sleep without atonia (RSWA) is a key feature for the diagnosis of rapid eye movement (REM) sleep behaviour disorder (RBD). We introduce RBDtector, a novel open-source software to score RSWA according to established SINBAR visual scoring criteria. We assessed muscle activity of the mentalis, flexor digitorum superficialis (FDS), and anterior tibialis (AT) muscles. RSWA was scored manually as tonic, phasic, and any activity by human scorers as well as using RBDtector in 20 subjects. Subsequently, 174 subjects (72 without RBD and 102 with RBD) were analysed with RBDtector to show the algorithm's applicability. We additionally compared RBDtector estimates to a previously published dataset. RBDtector showed robust conformity with human scorings. The highest congruency was achieved for phasic and any activity of the FDS. Combining mentalis any and FDS any, RBDtector identified RBD subjects with 100\% specificity and 96\% sensitivity applying a cut-off of 20.6\%. Comparable performance was obtained without manual artefact removal. RBD subjects also showed muscle bouts of higher amplitude and longer duration. RBDtector provides estimates of tonic, phasic, and any activity comparable to human scorings. RBDtector, which is freely available, can help identify RBD subjects and provides reliable RSWA metrics.},
  language  = {en}
}
@article{Gebhardt2005,
  author    = {Gebhardt, Andreas},
  title     = {Rapid Prototyping f{\"u}r metallische Werkst{\"u}cke: Direkte und indirekte Verfahren},
  year      = {2005},
  abstract  = {Die generative Herstellung von Kunststoffbauteilen hat im Gewand des Rapid Prototyping die Produktentwicklung nachhaltig positiv beeinflusst und ist im Begriff als Rapid Manufacturing die Fertigung zu revolutionieren. Je mehr sich die besonderen Eigenschaften generativ gefertigter Kunststoffbauteile herumsprechen, desto lauter wird der Ruf nach Metallbauteilen. Die Entwicklung entsprechender Prozesse l{\"a}uft auf Hochtouren, kann aber bisher aber erst vereinzelt Erfolge vorweisen. Dabei w{\"a}ren es gerade die Metallbauteile, die ausgestattet mit den besonderen Merkmalen generativ gefertigter Werkst{\"u}cke, in vielen Branchen einen deutlichen Entwicklungsschub ausl{\"o}sen k{\"o}nnten. F{\"u}r den potenziellen Anwender ist dabei besonders verwirrend, dass die unterschiedlichsten Ans{\"a}tze nebeneinander verfolgt werden. Im Folgenden soll daher der Versuche unternommen werden, dieses weite Feld systematisiert darzustellen und M{\"o}glichkeiten und Trends zu erl{\"a}utern.},
  subject      = {Rapid prototyping},
  language  = {de}
}
@article{Gebhardt2006,
  author    = {Gebhardt, Andreas},
  title     = {Rapid Manufacturing - eine interdisziplin{\"a}re Strategie},
  year      = {2006},
  abstract  = {Als um 1987 ein Verfahren namens Stereolithographie und ein Stereolithography Apparatus (SLA) vorgestellt wurden, war der Traum von der Herstellung beliebiger dreidimensionaler Bauteile direkt aus Computerdaten und ohne bauteilspezifische Werkzeuge Realit{\"a}t geworden. Ein Anwendungs-Szenario wurde gleich mitgeliefert. Diese Technologie w{\"u}rde es m{\"o}glich machen, die gesamte Ersatzteilversorgung der Amerikanischen Pazifikflotte mittels ein paar dieser Maschinen, umfangreicher Datenst{\"a}tze und gen{\"u}gend Rohmaterial vor Ort auf einem Flugzeugtr{\"a}ger direkt nach Bedarf zu fertigen. Diese Vorstellung definierte schon damals die direkte digitale Fertigung, das Rapid Manufacturing. In der Realit{\"a}t bestanden die mit diesem Verfahren hergestellten Bauteile nur aus Kunststoff, waren ungenau, bruchempfindlich und klebrig und allein in der Produktentwicklung, eben als Prototypen zu benutzen. Sie waren schnell verf{\"u}gbar, weil zu Ihrer Herstellung keine Werkzeuge ben{\"o}tigt wurden. Folgerichtige und zudem modern hießen sie: Rapid Prototyping. Rapid Prototyping wurde schnell zum Synonym eines neuen Zweiges der Fertigungstechnik, der Generativen Fertigungstechnik. Die weitere Entwicklung brachte neue Verfahren, h{\"o}here Genauigkeiten, verbesserte Werkstoffe und neue Anwendungen. Die Herstellung von Negativen, also Werkzeugen, mit dem gleichen Verfahren wurde marketing-getrieben Rapid Tooling genannt und als die ersten Bauteile nicht mehr als Prototypen, sondern als Endprodukte eingesetzt wurden, nannte man dies Rapid Manufacturing - das Ziel war erreicht. War das Ziel wirklich erreicht? Ist es Rapid Manufacturing, wenn ein generativ gefertigtes Bauteil die gew{\"u}nschte Spezifikation erreicht? Was muss passieren, damit aus dem Ph{\"a}nomen Rapid Prototyping eine Strategie wird, die geeignet ist, einen Paradigmenwechsel von der heutigen Hersteller-induzierten Massenproduktion von Massenartikeln zur Verbraucher-induzierten (und verantworteten) Massenproduktion von Einzelteilen f{\"u}r jedermann erm{\"o}glichen und m{\"o}glicherweise unsere Arbeits- und Lebensformen tiefgreifend zu beeinflussen? Im Beitrag wird der Begriff der (Fertigungs-) Strategie „Rapid Manufacturing" n{\"a}her beleuchtet. Es wird diskutiert, welche Maßnahmen auf der technischen und der operative Ebene getroffen werden m{\"u}ssen, damit die generative Fertigungstechnik im Sinne dieser Strategie umgesetzt werden kann. Beispiele belegen, dass diese Entwicklung bereits begonnen hat und geben Anregungen f{\"u}r eine konstruktive Diskussion auf der RapidTech 2006.},
  subject      = {Rapid prototyping},
  language  = {de}
}
@article{Wollert2016,
  author    = {Wollert, J{\"o}rg},
  title     = {Rapid Application Development},
  series = {Design \& Elektronik},
  journal   = {Design \& Elektronik},
  number    = {4},
  publisher = {WEKA-Fachmedien},
  address   = {M{\"u}nchen},
  issn      = {0933-8667},
  pages     = {8 -- 11},
  year      = {2016},
  abstract  = {Das IoT ist ohne eingebettete Systeme undenkbar. Erst kleine und kleinste Mikrocontroller mit intelligenten Kommunikationsschnittstellen und Anbindung ans Internet erm{\"o}glichen sinnvolles und fl{\"a}chendeckendes Einsammeln von Daten. Doch wie kompliziert ist der Einstieg in die Embedded-Welt? Dieser Artikel gibt Einblick, wie die »Arduino-Plattform« die Einstiegsh{\"u}rden f{\"u}r eingebettete Systeme dramatisch reduzieren kann.},
  language  = {de}
}
@article{PfaffBabilon2023,
  author    = {Pfaff, Raphael and Babilon, Katharina},
  title     = {Railway Challenge - moderne Auflage der Rainhill Trials?},
  series = {Eisenbahntechnische Rundschau : ETR ; Impulsgeber f{\"u}r das System Bahn},
  volume    = {2023},
  journal   = {Eisenbahntechnische Rundschau : ETR ; Impulsgeber f{\"u}r das System Bahn},
  number    = {4},
  publisher = {DVV Media Group},
  address   = {Hamburg},
  issn      = {0013-2845},
  pages     = {55 -- 58},
  year      = {2023},
  abstract  = {Die IMechE Railway Challenge wird j{\"a}hrlich in Stapleford, Großbritannien ausgetragen. Im Rahmen der Challenge entwickeln und bauen Studierende eine Lokomotive und vergleichen sich in verschiedenen Disziplinen, darunter eine automatisierte Zielbremsung, optimale Energier{\"u}ckgewinnung beim Bremsen und minimale Ger{\"a}uschemissionen. Neben diesen und weiteren technischen Wettbewerbsdisziplinen treten die Fahrzeuge und die Teams auch in nicht-technischen Disziplinen wie einer Business Case Challenge an.},
  language  = {de}
}
@article{TippkoetterRoth2020,
  author    = {Tippk{\"o}tter, Nils and Roth, Jasmine},
  title     = {Purified Butanol from Lignocellulose - Solvent-Impregnated Resins for an Integrated Selective Removal},
  series = {Chemie Ingenieur Technik},
  volume    = {92},
  journal   = {Chemie Ingenieur Technik},
  number    = {11},
  publisher = {Wiley-VCH},
  address   = {Weinheim},
  issn      = {1522-2640},
  doi       = {10.1002/cite.202000200},
  pages     = {1741 -- 1751},
  year      = {2020},
  abstract  = {In traditional microbial biobutanol production, the solvent must be recovered during fermentation process for a sufficient space-time yield. Thermal separation is not feasible due to the boiling point of n-butanol. As an integrated and selective solid-liquid separation alternative, solvent impregnated resins (SIRs) were applied. Two polymeric resins were evaluated and an extractant screening was conducted. Vacuum application with vapor collection in fixed-bed column as bioreactor bypass was successfully implemented as butanol desorption step. In course of further increasing process economics, fermentation with renewable lignocellulosic substrates was conducted using Clostridium acetobutylicum. Utilization of SIR was shown to be a potential strategy for solvent removal from fermentation broth, while application of a bypass column allows for product removal and recovery at once.},
  language  = {en}
}
@article{Starck2007,
  author    = {Starck, Andreas},
  title     = {Projektsteuerung contra Architektengrundleistung oder wer steuert das Baugeschehen?},
  year      = {2007},
  abstract  = {Sieht man sich die umfangreichen Bet{\"a}tigungsfelder f{\"u}r einen Projektsteuerer in den Publikationen der einschl{\"a}gigen Verb{\"a}nde und der Anbieter etwas genauer an, so wird man feststellen, das nach der eigentlichen Projektvorbereitungsphase mit Wirtschaftlichkeitsberechnungen und Sicherstellung der Finanzierung erhebliche {\"U}berschneidungen zu den in der HOAI ausgewiesenen T{\"a}tigkeiten der weiteren Planungsbeteiligten, insbesondere des Geb{\"a}udeplaners, also des Architekten bestehen. Geht man nun davon aus, dass der Bauherr diese Leistungen nicht doppelt bezahlen will, w{\"a}re die logische Konsequenz aus der vollumf{\"a}nglichen Beauftragung eines Projektsteuerers die Verminderung des Auftragsumfangs an den Architekten, verbunden mit einer Honorarminderung f{\"u}r den Architekten. Damit bricht dem Architekten bei eingehender Betrachtung am Ende mehr als die H{\"a}lfte seiner T{\"a}tigkeit und damit seiner Grundlage zur Honorarerzielung weg. Der Bauherr muss in erster Linie seine W{\"u}nsche definieren und sein Budget bestimmen. Er beauftragt die Planungsbeteiligten und nimmt deren Leistungen entgegen. Sein Problem dabei ist, dass er diese Leistung nicht beurteilen kann, weder in Bezug auf deren Vollst{\"a}ndigkeit, noch in Bezug auf deren Inhalt. Hier steht der Projektsteuerer im eigentlichen Sinne. Er muss wissen, was die Planungsbeteiligten f{\"u}r ihr Geld zu leisten haben und wie er diese Leistungen durchsetzen kann. Letztendlich sorgt er dann aber auch daf{\"u}r, das die Architektenleistungen, also Planung und Ausschreibungsunterlagen vom Bauherrn verstanden werden. Warum aber kann der Architekt selbst seine Leistungen und damit den Nachweis der Leistungserf{\"u}llung nicht selbst dem Bauherrn verst{\"a}ndlich und damit glaubhaft machen? Es liegt also letztlich in der Hand der Architekten, ob ihr Bet{\"a}tigungsfeld weiter durch in die Planung und Gestaltung eingreifende, zus{\"a}tzliche Projektsteuerer und Generalunternehmer eingeengt oder sogar weggenommen werden kann. Die Frage, wer das Baugeschehen steuert und lenkt bleibt solange ungekl{\"a}rt, wie die Architekten dieses T{\"a}tigkeitsfeld des Architekten im Baubetrieb weiterhin nur unzul{\"a}nglich ausf{\"u}llen k{\"o}nnen und wollen.},
  language  = {de}
}
@article{Lohr1998,
  author    = {Lohr, J{\"u}rgen},
  title     = {Probleme der Multimedia Dienste im nationalen und internationalen Umfeld},
  year      = {1998},
  abstract  = {In: Telekom-Praxis. Ausgabe 1998. 25 S.},
  subject      = {Multimediamarkt},
  language  = {de}
}
@article{Staat2004,
  author    = {Staat, Manfred},
  title     = {Plastic collapse analysis of longitudinally flawed pipes and vessels},
  year      = {2004},
  abstract  = {Improved collapse loads of thick-walled, crack containing pipes and vessels are suggested. Very deep cracks have a residual strength which is better modelled by a global limit load. In all burst tests, the ductility of pressure vessel steels was sufficiently high whereby the burst pressure could be predicted by limit analysis with no need to apply fracture mechanics. The relative prognosis error increases however, for long and deep defects due to uncertainties of geometry and strength data.},
  subject      = {Druckbeh{\"a}lter},
  language  = {en}
}
@article{WeldenNagamineKomesuWagneretal.2021,
  author    = {Welden, Rene and Nagamine Komesu, Cindy A. and Wagner, Patrick H. and Sch{\"o}ning, Michael Josef and Wagner, Torsten},
  title     = {Photoelectrochemical enzymatic penicillin biosensor: A proof-of-concept experiment},
  series = {Electrochemical Science Advances},
  volume    = {2},
  journal   = {Electrochemical Science Advances},
  number    = {4},
  publisher = {Wiley-VCH},
  address   = {Weinheim},
  issn      = {2698-5977},
  doi       = {10.1002/elsa.202100131},
  pages     = {1 -- 5},
  year      = {2021},
  abstract  = {Photoelectrochemical (PEC) biosensors are a rather novel type of biosensors thatutilizelighttoprovideinformationaboutthecompositionofananalyte,enablinglight-controlled multi-analyte measurements. For enzymatic PEC biosensors,amperometric detection principles are already known in the literature. In con-trast, there is only a little information on H+-ion sensitive PEC biosensors. Inthis work, we demonstrate the detection of H+ions emerged by H+-generatingenzymes, exemplarily demonstrated with penicillinase as a model enzyme on atitanium dioxide photoanode. First, we describe the pH sensitivity of the sensorand study possible photoelectrocatalytic reactions with penicillin. Second, weshow the enzymatic PEC detection of penicillin.},
  language  = {en}
}
@article{Wollert2016,
  author    = {Wollert, J{\"o}rg},
  title     = {OS-Funktionalit{\"a}t ohne OS f{\"u}r das IoT},
  series = {Design \& Elektronik},
  journal   = {Design \& Elektronik},
  number    = {11},
  publisher = {WEKA-Fachmedien},
  address   = {M{\"u}nchen},
  issn      = {0933-8667},
  pages     = {85 -- 90},
  year      = {2016},
  abstract  = {Low-end-Embedded-Plattformen stellen eine hohe Anforderung an die Entscheidungsf{\"a}higkeit des Entwicklers: Zum n{\"a}chstgr{\"o}ßeren Prozessor greifen und ein Betriebssystem benutzen oder doch besser auf das Betriebssystem verzichten? Die Frage l{\"a}sst sich einfach beantworten: Einen Nanokernel verwenden und das Embedded-System mit einem minimalen Footprint realisieren. Adam Dunkels Protothreads sind eine ausgesprochen effiziente Art, Mikrocontroller gut strukturiert zu programmieren und gleichzeitig auf Overhead zu verzichten. So k{\"o}nnen auch mit kleinen 8-bit-Prozessoren anspruchsvolle Aufgaben in einem Thread-Modell bearbeitet werden. Man muss also nicht immer das Rad neu erfinden oder gleich auf Linux-basierte Systeme zur{\"u}ckgreifen.},
  language  = {de}
}
@article{CheenakulaPaulsenOttetal.2023,
  author    = {Cheenakula, Dheeraja and Paulsen, Svea and Ott, Fabian and Gr{\"o}mping, Markus},
  title     = {Operational window of a deammonifying sludge for mainstream application in a municipal wastewater treatment plant},
  series = {Water and Environment Journal},
  journal   = {Water and Environment Journal},
  number    = {Early View},
  publisher = {Wiley},
  address   = {Chichester},
  issn      = {1747-6593},
  doi       = {10.1111/wej.12898},
  pages     = {1 -- 12},
  year      = {2023},
  abstract  = {The present work aimed to study the mainstream feasibility of the deammonifying sludge of side stream of municipal wastewater treatment plant (MWWTP) in Kaster, Germany. For this purpose, the deammonifying sludge available at the side stream was investigated for nitrogen (N) removal with respect to the operational factors temperature (15-30°C), pH value (6.0-8.0) and chemical oxygen demand (COD)/N ratio (≤1.5-6.0). The highest and lowest N-removal rates of 0.13 and 0.045 kg/(m³ d) are achieved at 30 and 15°C, respectively. Different conditions of pH and COD/N ratios in the SBRs of Partial nitritation/anammox (PN/A) significantly influenced both the metabolic processes and associated N-removal rates. The scientific insights gained from the current work signifies the possibility of mainstream PN/A at WWTPs. The current study forms a solid basis of operational window for the upcoming semi-technical trails to be conducted prior to the full-scale mainstream PN/A at WWTP Kaster and WWTPs globally.},
  language  = {en}
}
@article{MoehrenBergmannJanseretal.2023,
  author    = {M{\"o}hren, Felix and Bergmann, Ole and Janser, Frank and Braun, Carsten},
  title     = {On the influence of elasticity on propeller performance: a parametric study},
  series = {CEAS Aeronautical Journal},
  volume    = {14},
  journal   = {CEAS Aeronautical Journal},
  publisher = {Springer Nature},
  address   = {Berlin},
  issn      = {1869-5590 (Online)},
  doi       = {10.1007/s13272-023-00649-y},
  pages     = {311 -- 323},
  year      = {2023},
  abstract  = {The aerodynamic performance of propellers strongly depends on their geometry and, consequently, on aeroelastic deformations. Knowledge of the extent of the impact is crucial for overall aircraft performance. An integrated simulation environment for steady aeroelastic propeller simulations is presented. The simulation environment is applied to determine the impact of elastic deformations on the aerodynamic propeller performance. The aerodynamic module includes a blade element momentum approach to calculate aerodynamic loads. The structural module is based on finite beam elements, according to Timoshenko theory, including moderate deflections. Several fixed-pitch propellers with thin-walled cross sections made of both isotropic and non-isotropic materials are investigated. The essential parameters are varied: diameter, disc loading, sweep, material, rotational, and flight velocity. The relative change of thrust between rigid and elastic blades quantifies the impact of propeller elasticity. Swept propellers of large diameters or low disc loadings can decrease the thrust significantly. High flight velocities and low material stiffness amplify this tendency. Performance calculations without consideration of propeller elasticity can lead to decreased efficiency. To avoid cost- and time-intense redesigns, propeller elasticity should be considered for swept planforms and low disc loadings.},
  language  = {en}
}
@article{HaegerJolmesOyenetal.2024,
  author    = {Haeger, Gerrit and Jolmes, Tristan and Oyen, Sven and Jaeger, Karl-Erich and Bongaerts, Johannes and Sch{\"o}rken, Ulrich and Siegert, Petra},
  title     = {Novel recombinant aminoacylase from Paraburkholderia monticola capable of N-acyl-amino acid synthesis},
  series = {Applied Microbiology and Biotechnology},
  journal   = {Applied Microbiology and Biotechnology},
  number    = {108},
  publisher = {Springer},
  address   = {Berlin},
  issn      = {1432-0614},
  doi       = {10.1007/s00253-023-12868-8},
  pages     = {14 Seiten},
  year      = {2024},
  abstract  = {N-Acyl-amino acids can act as mild biobased surfactants, which are used, e.g., in baby shampoos. However, their chemical synthesis needs acyl chlorides and does not meet sustainability criteria. Thus, the identification of biocatalysts to develop greener synthesis routes is desirable. We describe a novel aminoacylase from Paraburkholderia monticola DSM 100849 (PmAcy) which was identified, cloned, and evaluated for its N-acyl-amino acid synthesis potential. Soluble protein was obtained by expression in lactose autoinduction medium and co-expression of molecular chaperones GroEL/S. Strep-tag affinity purification enriched the enzyme 16-fold and yielded 15 mg pure enzyme from 100 mL of culture. Biochemical characterization revealed that PmAcy possesses beneficial traits for industrial application like high temperature and pH-stability. A heat activation of PmAcy was observed upon incubation at temperatures up to 80 °C. Hydrolytic activity of PmAcy was detected with several N-acyl-amino acids as substrates and exhibited the highest conversion rate of 773 U/mg with N-lauroyl-L-alanine at 75 °C. The enzyme preferred long-chain acyl-amino-acids and displayed hardly any activity with acetyl-amino acids. PmAcy was also capable of N-acyl-amino acid synthesis with good conversion rates. The best synthesis results were obtained with the cationic L-amino acids L-arginine and L-lysine as well as with L-leucine and L-phenylalanine. Exemplarily, L-phenylalanine was acylated with fatty acids of chain lengths from C8 to C18 with conversion rates of up to 75\%. N-lauroyl-L-phenylalanine was purified by precipitation, and the structure of the reaction product was verified by LC-MS and NMR.},
  language  = {en}
}
@article{HaegerProbstJaegeretal.2023,
  author    = {Haeger, Gerrit and Probst, Johanna and Jaeger, Karl-Erich and Bongaerts, Johannes and Siegert, Petra},
  title     = {Novel aminoacylases from Streptomyces griseus DSM 40236 and their recombinant production in Streptomyces lividans},
  series = {FEBS Open Bio},
  volume    = {13},
  journal   = {FEBS Open Bio},
  number    = {12},
  publisher = {Wiley},
  address   = {Hoboken, NJ},
  issn      = {2211-5463},
  doi       = {10.1002/2211-5463.13723},
  pages     = {2224 -- 2238},
  year      = {2023},
  abstract  = {Amino acid-based surfactants are valuable compounds for cosmetic formulations. The chemical synthesis of acyl-amino acids is conventionally performed by the Schotten-Baumann reaction using fatty acyl chlorides, but aminoacylases have also been investigated for use in biocatalytic synthesis with free fatty acids. Aminoacylases and their properties are diverse; they belong to different peptidase families and show differences in substrate specificity and biocatalytic potential. Bacterial aminoacylases capable of synthesis have been isolated from Burkholderia, Mycolicibacterium, and Streptomyces. Although several proteases and peptidases from S. griseus have been described, no aminoacylases from this species have been identified yet. In this study, we investigated two novel enzymes produced by S. griseus DSM 40236ᵀ . We identified and cloned the respective genes and recombinantly expressed an α-aminoacylase (EC 3.5.1.14), designated SgAA, and an ε-lysine acylase (EC 3.5.1.17), designated SgELA, in S. lividans TK23. The purified aminoacylase SgAA was biochemically characterized, focusing on its hydrolytic activity to determine temperature- and pH optima and stabilities. The aminoacylase could hydrolyze various acetyl-amino acids at the Nα -position with a broad specificity regarding the sidechain. Substrates with longer acyl chains, like lauroyl-amino acids, were hydrolyzed to a lesser extent. Purified aminoacylase SgELA specific for the hydrolysis of Nε -acetyl-L-lysine was unstable and lost its enzymatic activity upon storage for a longer period but could initially be characterized. The pH optimum of SgELA was pH 8.0. While synthesis of acyl-amino acids was not observed with SgELA, SgAA catalyzed the synthesis of lauroyl-methionine.},
  language  = {en}
}
@article{FalkenbergVossBottetal.2023,
  author    = {Falkenberg, Fabian and Voß, Leonie and Bott, Michael and Bongaerts, Johannes and Siegert, Petra},
  title     = {New robust subtilisins from halotolerant and halophilic Bacillaceae},
  series = {Applied Microbiology and Biotechnology},
  volume    = {107},
  journal   = {Applied Microbiology and Biotechnology},
  publisher = {Springer Nature},
  address   = {Berlin},
  issn      = {1432-0614},
  doi       = {10.1007/s00253-023-12553-w},
  pages     = {3939 -- 3954},
  year      = {2023},
  abstract  = {The aim of the present study was the characterisation of three true subtilisins and one phylogenetically intermediate subtilisin from halotolerant and halophilic microorganisms. Considering the currently growing enzyme market for efficient and novel biocatalysts, data mining is a promising source for novel, as yet uncharacterised enzymes, especially from halophilic or halotolerant Bacillaceae, which offer great potential to meet industrial needs. Both halophilic bacteria Pontibacillus marinus DSM 16465ᵀ and Alkalibacillus haloalkaliphilus DSM 5271ᵀ and both halotolerant bacteria Metabacillus indicus DSM 16189 and Litchfieldia alkalitelluris DSM 16976ᵀ served as a source for the four new subtilisins SPPM, SPAH, SPMI and SPLA. The protease genes were cloned and expressed in Bacillus subtilis DB104. Purification to apparent homogeneity was achieved by ethanol precipitation, desalting and ion-exchange chromatography. Enzyme activity could be observed between pH 5.0-12.0 with an optimum for SPPM, SPMI and SPLA around pH 9.0 and for SPAH at pH 10.0. The optimal temperature for SPMI and SPLA was 70 °C and for SPPM and SPAH 55 °C and 50 °C, respectively. All proteases showed high stability towards 5\% (w/v) SDS and were active even at NaCl concentrations of 5 M. The four proteases demonstrate potential for future biotechnological applications.},
  language  = {en}
}
@article{PicardBrillCasseletal.2002,
  author    = {Picard, Antoni and Brill, Manfred and Cassel, Detlev and Jentsch, Andreas and Rollwa, Markus and K{\"a}mper, Klaus-Peter and Merten, Sabine},
  title     = {Neue Medien f{\"u}r die praktische MST-Ausbildung},
  organization    = {FH-Kaiserslautern},
  year      = {2002},
  abstract  = {Im Studiengang Mikrosystemtechnik des Fachhochschulstandortes Zweibr{\"u}cken werden zwei neue moderne Anlagen f{\"u}r die Herstellung von mikrotechnischen Komponenten in Betrieb genommen: Ein Oxidationsofen f{\"u}r Herstellung d{\"u}nner Oxidschichten auf Silizium-Einkristallen und eine Belichtungsapparatur f{\"u}r die Fotolithografie - das Besondere an diesen Anlagen: Sie existieren nur virtuell, d.h. als Animationen in einer Computerwelt.},
  subject      = {Mikrosystemtechnik},
  language  = {de}
}
@article{BlankeHagenkampDoeringetal.2021,
  author    = {Blanke, Tobias and Hagenkamp, Markus and D{\"o}ring, Bernd and G{\"o}ttsche, Joachim and Reger, Vitali and Kuhnhenne, Markus},
  title     = {Net-exergetic, hydraulic and thermal optimization of coaxial heat exchangers using fixed flow conditions instead of fixed flow rates},
  series = {Geothermal Energy},
  volume    = {9},
  journal   = {Geothermal Energy},
  number    = {Article number: 19},
  publisher = {Springer},
  address   = {Berlin},
  issn      = {2195-9706},
  doi       = {10.1186/s40517-021-00201-3},
  pages     = {23 Seiten},
  year      = {2021},
  abstract  = {Previous studies optimized the dimensions of coaxial heat exchangers using constant mass fow rates as a boundary condition. They show a thermal optimal circular ring width of nearly zero. Hydraulically optimal is an inner to outer pipe radius ratio of 0.65 for turbulent and 0.68 for laminar fow types. In contrast, in this study, fow conditions in the circular ring are kept constant (a set of fxed Reynolds numbers) during optimization. This approach ensures fxed fow conditions and prevents inappropriately high or low mass fow rates. The optimization is carried out for three objectives: Maximum energy gain, minimum hydraulic efort and eventually optimum net-exergy balance. The optimization changes the inner pipe radius and mass fow rate but not the Reynolds number of the circular ring. The thermal calculations base on Hellstr{\"o}m's borehole resistance and the hydraulic optimization on individually calculated linear loss of head coefcients. Increasing the inner pipe radius results in decreased hydraulic losses in the inner pipe but increased losses in the circular ring. The net-exergy diference is a key performance indicator and combines thermal and hydraulic calculations. It is the difference between thermal exergy fux and hydraulic efort. The Reynolds number in the circular ring is instead of the mass fow rate constant during all optimizations. The result from a thermal perspective is an optimal width of the circular ring of nearly zero. The hydraulically optimal inner pipe radius is 54\% of the outer pipe radius for laminar fow and 60\% for turbulent fow scenarios. Net-exergetic optimization shows a predominant infuence of hydraulic losses, especially for small temperature gains. The exact result depends on the earth's thermal properties and the fow type. Conclusively, coaxial geothermal probes' design should focus on the hydraulic optimum and take the thermal optimum as a secondary criterion due to the dominating hydraulics.},
  language  = {en}
}
@article{KarschuckSchmidtAchtsnichtetal.2023,
  author    = {Karschuck, Tobias and Schmidt, Stefan and Achtsnicht, Stefan and Poghossian, Arshak and Wagner, Patrick and Sch{\"o}ning, Michael Josef},
  title     = {Multiplexing system for automated characterization of a capacitive field-effect sensor array},
  series = {Physica Status Solidi A},
  volume    = {220},
  journal   = {Physica Status Solidi A},
  number    = {22},
  publisher = {Wiley-VCH},
  address   = {Weinheim},
  issn      = {1862-6300 (Print)},
  doi       = {10.1002/pssa.202300265},
  pages     = {7 Seiten},
  year      = {2023},
  abstract  = {In comparison to single-analyte devices, multiplexed systems for a multianalyte detection offer a reduced assay time and sample volume, low cost, and high throughput. Herein, a multiplexing platform for an automated quasi-simultaneous characterization of multiple (up to 16) capacitive field-effect sensors by the capacitive-voltage (C-V) and the constant-capacitance (ConCap) mode is presented. The sensors are mounted in a newly designed multicell arrangement with one common reference electrode and are electrically connected to the impedance analyzer via the base station. A Python script for the automated characterization of the sensors executes the user-defined measurement protocol. The developed multiplexing system is tested for pH measurements and the label-free detection of ligand-stabilized, charged gold nanoparticles.},
  language  = {en}
}
@article{AdelsElbersDiehletal.2023,
  author    = {Adels, Klaudia and Elbers, Gereon and Diehl, Bernd and Monakhova, Yulia},
  title     = {Multicomponent analysis of dietary supplements containing glucosamine and chondroitin: comparative low- and high-field NMR spectroscopic study},
  series = {Analytical Sciences},
  volume    = {2023},
  journal   = {Analytical Sciences},
  publisher = {Springer Verlag},
  address   = {Cham},
  issn      = {1348-2246 (Online)},
  doi       = {10.1007/s44211-023-00433-2},
  pages     = {13 Seiten},
  year      = {2023},
  abstract  = {With the prevalence of glucosamine- and chondroitin-containing dietary supplements for people with osteoarthritis in the marketplace, it is important to have an accurate and reproducible analytical method for the quantitation of these compounds in finished products. NMR spectroscopic method based both on low- (80 MHz) and high- (500-600 MHz) field NMR instrumentation was established, compared and validated for the determination of chondroitin sulfate and glucosamine in dietary supplements. The proposed method was applied for analysis of 20 different dietary supplements. In the majority of cases, quantification results obtained on the low-field NMR spectrometer are similar to those obtained with high-field 500-600 MHz NMR devices. Validation results in terms of accuracy, precision, reproducibility, limit of detection and recovery demonstrated that the developed method is fit for purpose for the marketed products. The NMR method was extended to the analysis of methylsulfonylmethane, adulterant maltodextrin, acetate and inorganic ions. Low-field NMR can be a quicker and cheaper alternative to more expensive high-field NMR measurements for quality control of the investigated dietary supplements. High-field NMR instrumentation can be more favorable for samples with complex composition due to better resolution, simultaneously giving the possibility of analysis of inorganic species such as potassium and chloride.},
  language  = {en}
}
@article{Lohr2000,
  author    = {Lohr, J{\"u}rgen},
  title     = {MPEG-Standards f{\"u}r Multimedia-Dienste (Video-Standards f{\"u}r Multimedia)},
  year      = {2000},
  abstract  = {Zuerst erschienen in Telekom-Praxis Ausgabe 2000. 24 S. Innovative multimediale Dienste werden durch die Globalisierung und Konvergenz der M{\"a}rkte, als auch durch Provider-Strategien ausgerichtet. Grundlegende Innovationsfelder sind: Globaler Zugang, Navigation und Intelligenter Inhalt. Die MPEG-Standards - im besonderen MPEG-4 und MPEG-7 - helfen, die oben genannten Forderungen zu erf{\"u}llen. Weiterhin erm{\"o}glichen sie auch f{\"u}r die Provider und den Kunden eine Zukunftssicherheit zu geben und einen zeitlichen Bestand f{\"u}r innovative Produkte zu sichern. Die Aufw{\"a}rtkompabilit{\"a}t der MPEG-Standards erm{\"o}glicht die Vermeidung von {\"U}berschneidung und die Erschließung neuer Dimensionen.},
  subject      = {Multimediamarkt},
  language  = {de}
}
@article{Lohr2000,
  author    = {Lohr, J{\"u}rgen},
  title     = {Modellierung von Multimedia-Diensten mit Hilfe der Chaostheorie},
  year      = {2000},
  abstract  = {In: Unterrichtsbl{\"a}tter / Deutsche Telekom AG. 53. 2000. 11. S. 618-634 (17 S.) Wo man hinblickt: Turbulenzen, Unvorhersagbarkeiten, Unregelm{\"a}ßigkeiten - kurz Chaos. Ist unsere wissenschaftliche Sichtweise falsch, alle Vorg{\"a}nge des Kosmos auf die Basis der Ordnung abzubilden? - Nein. Mit Chaos ist nicht Fehlen jeglicher Ordnung und v{\"o}llig regelloses Durcheinander gemeint, sondern - auf Grund der Vernetztheit der vielen Elemente, die miteinander eine Wechselwirkung haben - die Unberechenbarkeit der Naturprozesse. Die Chaostheorie erlaubt durch die Modellierung weit auseinander liegende Problemfelder miteinander zu verkn{\"u}pfen, um dann in einem Modell die Zusammenh{\"a}nge erkennbar zu machen. Mit Hilfe der Chaostheorie werden gesellschaftliche Prozesse abgebildet und dann mit einer Simulation neue, globale Strategien erstellt, um kritische Systempunkte (Systemelemente) zu erkennen. Der nachfolgende Beitrag beschreibt die Modellierung am Beispiel der Multimedia-Dienste und gibt mit einem umfassenden Glossar eine Einf{\"u}hrung in die Begrifflichkeiten der Chaostheorie. Die Chaostheorie ist die mathematisch-physikalische Theorie zur Beschreibung von Systemen, die zwar durch Gesetzm{\"a}ßigkeiten determiniert sind, bei denen aber kleine {\"A}nderungen der Anfangsbedingungen ein exponentielles Anwachsen von St{\"o}rungen bewirken. Das Verhalten derartiger Systeme f{\"u}hrt zur Ausbildung chaotischer Strukturen und ist langfristig nicht vorhersagbar. Die Chaostheorie ist beispielsweise in der nichtlinearen Optik, bei chemischen Reaktionen und der Wettervorhersage anwendbar.},
  subject      = {Chaostheorie},
  language  = {de}
}
@article{MolinnusIkenJohnenetal.2022,
  author    = {Molinnus, Denise and Iken, Heiko and Johnen, Anna Lynn and Richstein, Benjamin and Hellmich, Lena and Poghossian, Arshak and Knoch, Joachim and Sch{\"o}ning, Michael Josef},
  title     = {Miniaturized pH-Sensitive Field-Effect Capacitors with Ultrathin Ta₂O₅ Films Prepared by Atomic Layer Deposition},
  series = {physica status solidi (a) applications and materials science},
  volume    = {219},
  journal   = {physica status solidi (a) applications and materials science},
  number    = {8},
  publisher = {Wiley-VCH},
  address   = {Weinheim},
  issn      = {1862-6319},
  doi       = {10.1002/pssa.202100660},
  pages     = {7 Seiten},
  year      = {2022},
  abstract  = {Miniaturized electrolyte-insulator-semiconductor capacitors (EISCAPs) with ultrathin gate insulators have been studied in terms of their pH-sensitive sensor characteristics: three different EISCAP systems consisting of Al-p-Si-Ta2O5(5 nm), Al-p-Si-Si3N4(1 or 2 nm)-Ta2O5 (5 nm), and Al-p-Si-SiO2(3.6 nm)-Ta2O5(5 nm) layer structures are characterized in buffer solution with different pH values by means of capacitance-voltage and constant capacitance method. The SiO2 and Si3N4 gate insulators are deposited by rapid thermal oxidation and rapid thermal nitridation, respectively, whereas the Ta2O5 film is prepared by atomic layer deposition. All EISCAP systems have a clear pH response, favoring the stacked gate insulators SiO2-Ta2O5 when considering the overall sensor characteristics, while the Si3N4(1 nm)-Ta2O5 stack delivers the largest accumulation capacitance (due to the lower equivalent oxide thickness) and a higher steepness in the slope of the capacitance-voltage curve among the studied stacked gate insulator systems.},
  language  = {en}
}
@article{FingerGoettenBraunetal.2020,
  author    = {Finger, Felix and G{\"o}tten, Falk and Braun, Carsten and Bil, Cees},
  title     = {Mass, primary energy, and cost: the impact of optimization objectives on the initial sizing of hybrid-electric general aviation aircraft},
  series = {CEAS Aeronautical Journal},
  volume    = {2020},
  journal   = {CEAS Aeronautical Journal},
  number    = {11},
  publisher = {Springer},
  address   = {Heidelberg},
  issn      = {1869-5590},
  doi       = {10.1007/s13272-020-00449-8},
  pages     = {713 -- 730},
  year      = {2020},
  abstract  = {For short take-off and landing (STOL) aircraft, a parallel hybrid-electric propulsion system potentially offers superior performance compared to a conventional propulsion system, because the short-take-off power requirement is much higher than the cruise power requirement. This power-matching problem can be solved with a balanced hybrid propulsion system. However, there is a trade-off between wing loading, power loading, the level of hybridization, as well as range and take-off distance. An optimization method can vary design variables in such a way that a minimum of a particular objective is attained. In this paper, a comparison between the optimization results for minimum mass, minimum consumed primary energy, and minimum cost is conducted. A new initial sizing algorithm for general aviation aircraft with hybrid-electric propulsion systems is applied. This initial sizing methodology covers point performance, mission performance analysis, the weight estimation process, and cost estimation. The methodology is applied to the design of a STOL general aviation aircraft, intended for on-demand air mobility operations. The aircraft is sized to carry eight passengers over a distance of 500 km, while able to take off and land from short airstrips. Results indicate that parallel hybrid-electric propulsion systems must be considered for future STOL aircraft.},
  language  = {en}
}
@article{Staat2005,
  author    = {Staat, Manfred},
  title     = {Local and global collapse pressure of longitudinally flawed pipes and cylindrical vessels},
  year      = {2005},
  abstract  = {Limit loads can be calculated with the finite element method (FEM) for any component, defect geometry, and loading. FEM suggests that published long crack limit formulae for axial defects under-estimate the burst pressure for internal surface defects in thick pipes while limit loads are not conservative for deep cracks and for pressure loaded crack-faces. Very deep cracks have a residual strength, which is modelled by a global collapse load. These observations are combined to derive new analytical local and global collapse loads. The global collapse loads are close to FEM limit analyses for all crack dimensions.},
  subject      = {Finite-Elemente-Methode},
  language  = {en}
}
@article{Staat2001,
  author    = {Staat, Manfred},
  title     = {LISA - a European project for FEM-based limit and shakedown analysis},
  year      = {2001},
  abstract  = {The load-carrying capacity or the safety against plastic limit states are the central questions in the design of structures and passive components in the apparatus engineering. A precise answer is most simply given by limit and shakedown analysis. These methods can be based on static and kinematic theorems for lower and upper bound analysis. Both may be formulated as optimization problems for finite element discretizations of structures. The problems of large-scale analysis and the extension towards realistic material modelling will be solved in a European research project. Limit and shakedown analyses are briefly demonstrated with illustrative examples.},
  subject      = {Einspielen <Werkstoff>},
  language  = {en}
}
@article{StaatHeitzer1997,
  author    = {Staat, Manfred and Heitzer, M.},
  title     = {Limit and Shakedown Analysis Using a General Purpose Finite Element Code},
  series = {Proceedings of NAFEMS World Congress '97 on Design, Simulation \& Optimisation : reliability \& applicability of computational methods ; Stuttgart, Germany, 9 - 11 April 1997},
  journal   = {Proceedings of NAFEMS World Congress '97 on Design, Simulation \& Optimisation : reliability \& applicability of computational methods ; Stuttgart, Germany, 9 - 11 April 1997},
  publisher = {NAFEMS},
  address   = {Glasgow},
  isbn      = {1-87437-620-4},
  pages     = {522 -- 533},
  year      = {1997},
  language  = {en}
}
@article{DanielStarck2007,
  author    = {Daniel, Bernd and Starck, Andreas},
  title     = {Kostenkontrolle und Kostensteuerung im Hochbau},
  year      = {2007},
  abstract  = {Textauszug: Nach dem Leistungsbild der HOAI hat der Architekt bei Planung und Baubetrieb vier Stationen der Kostenermittlung entsprechend der DIN 276, Abschnitt 2.3 abzuarbeiten. Der Architekt, der seiner Verantwortung gerecht werden will, wird hier weitere Kontrollmechanismen einbauen wollen. {\"U}ber die genannten Kostenermittlungen hinaus kennt die DIN 276 daher noch das Erfordernis der Kostenkontrolle in Abschnitt 2.4 und der Kostensteuerung in Abschnitt 2.5. Die Kostensteuerung greift immer dann, wenn die Kostenkontrolle eine Abweichung des Kostenrahmens von den Sollwerten aufzeigt. Dazu m{\"u}ssen die Kontrollinstanzen dort eingebaut werden, wo Korrekturen noch m{\"o}glich sind. Eine erste Kontrolle der Kosten ist daher zwischen Massenermittlung und Vergabe sinnvoll einzuflechten. Zu diesem Zeitpunkt kann die Planung noch ver{\"a}ndert werden, was einen ersten steuernden Eingriff in die Baukosten erm{\"o}glicht, und zwar bevor die Angebotsunterlagen verschickt werden. Die Grundlagen zu einer effektiven Kostensteuerung werden in der Mengenermittlung der Leistungsphase 6 gelegt. Wenn dort die Mengen nicht sorgf{\"a}ltig und nachvollziehbar ermittelt wurden, wird der Soll- Ist- Abgleich w{\"a}hrend der Bauphase nicht fr{\"u}hzeitig genug gelingen, wenn nicht gar ganz entfallen. Es gilt also, daf{\"u}r zu sorgen, dass die Mengenermittlung zur Vergabe mit entsprechender Sorgfalt und vor Allem „projektnah" erfolgt. Sch{\"a}tzungen haben hier keine Berechtigung.},
  subject      = {Projektsteuerung},
  language  = {de}
}
@article{Heger2004,
  author    = {Heger, Michael},
  title     = {Konzept hochschuldidaktischer Aktionsforschung am Beispiel INGMEDIA},
  year      = {2004},
  abstract  = {"INGMEDIA: Entwicklung und Evaluation interaktiver, multimedialer Lernsoftware f{\"u}r technische und physikalische Praktika in Ingenieurstudieng{\"a}ngen". So lautet der Titel des vom bmb+f im F{\"o}rderprogramm "Neue Medien in der Hochschullehre" unterst{\"u}tzten Verbundprojekts. [...] Im vorliegenden Beitrag wird {\"u}ber das Evaluationskonzept von INGMEDIA berichtet. Es handelt sich hierbei um einen im E-Learning-Bereich bisher kaum vertretenen Ansatz hochschuldidaktischer Aktionsforschung. Der Beitrag betont entsprechend des kevih - Tagungskonzepts (T{\"u}bingen 11./12.3.03) die besonderen hochschuldidaktischen Zielrichtungen, fokussiert also klar auf der konzeptionellen Ebene. Die Umsetzung und Evaluationsergebnisse zu INGMEDIA werden nach Projektabschluss an anderer Stelle ver{\"o}ffentlicht.},
  language  = {de}
}
@article{SchermutzkiKluss2004,
  author    = {Schermutzki, Margret and Kluß, Stefan},
  title     = {Kontaktstunden oder workload? Die Vergabe von ECTS credits},
  year      = {2004},
  abstract  = {Informationen dar{\"u}ber, wie die Arbeitsbelastung (workload) der Studierenden ermittelt werden kann},
  subject      = {Bologna-Prozess},
  language  = {de}
}
@article{DachwaldUlamecPostbergetal.2020,
  author    = {Dachwald, Bernd and Ulamec, Stephan and Postberg, Frank and Sohl, Frank and Vera, Jean-Pierre de and Christoph, Waldmann and Lorenz, Ralph D. and Hellard, Hugo and Biele, Jens and Rettberg, Petra},
  title     = {Key technologies and instrumentation for subsurface exploration of ocean worlds},
  series = {Space Science Reviews},
  volume    = {216},
  journal   = {Space Science Reviews},
  number    = {Art. 83},
  publisher = {Springer},
  address   = {Dordrecht},
  issn      = {1572-9672},
  doi       = {10.1007/s11214-020-00707-5},
  pages     = {45},
  year      = {2020},
  abstract  = {In this chapter, the key technologies and the instrumentation required for the subsurface exploration of ocean worlds are discussed. The focus is laid on Jupiter's moon Europa and Saturn's moon Enceladus because they have the highest potential for such missions in the near future. The exploration of their oceans requires landing on the surface, penetrating the thick ice shell with an ice-penetrating probe, and probably diving with an underwater vehicle through dozens of kilometers of water to the ocean floor, to have the chance to find life, if it exists. Technologically, such missions are extremely challenging. The required key technologies include power generation, communications, pressure resistance, radiation hardness, corrosion protection, navigation, miniaturization, autonomy, and sterilization and cleaning. Simpler mission concepts involve impactors and penetrators or - in the case of Enceladus - plume-fly-through missions.},
  language  = {en}
}
@article{WollertBooke2016,
  author    = {Wollert, J{\"o}rg and Booke, Andreas},
  title     = {IoT von der Stange},
  series = {elektronik},
  journal   = {elektronik},
  number    = {21 (2016)},
  publisher = {WEKA-Fachmedien},
  address   = {M{\"u}nchen},
  pages     = {30 -- 37},
  year      = {2016},
  abstract  = {Heute sollte am besten jedes Ger{\"a}t in die große Rechnerwolke eingebettet werden. Doch so einfach ist das nicht, denn Cloud ist viel mehr als nur das Internet der Dinge. Als Anwender muss man sich also fragen, welche Dienste man m{\"o}chte und welchem Anbieter man sein Vertrauen schenkt.},
  language  = {de}
}
@article{Wollert2015,
  author    = {Wollert, J{\"o}rg},
  title     = {IO-Link - f{\"u}r smarte Sensoren},
  series = {elektroniknet.de},
  journal   = {elektroniknet.de},
  year      = {2015},
  language  = {de}
}
@article{CapitainWagnerHummeletal.2021,
  author    = {Capitain, Charlotte and Wagner, Sebastian and Hummel, Joana and Tippk{\"o}tter, Nils},
  title     = {Investigation of C-N Formation Between Catechols and Chitosan for the Formation of a Strong, Novel Adhesive Mimicking Mussel Adhesion},
  series = {Waste and Biomass Valorization},
  volume    = {12},
  journal   = {Waste and Biomass Valorization},
  publisher = {Springer Nature},
  address   = {Cham},
  issn      = {1877-265X},
  doi       = {10.1007/s12649-020-01110-5},
  pages     = {1761 -- 1779},
  year      = {2021},
  language  = {en}
}
@article{WettingfeldKernKraemeretal.2009,
  author    = {Wettingfeld, J{\"u}rgen and Kern, Alexander and Kr{\"a}mer, Heinz-Josef and Thorm{\"a}hlen, Reyno},
  title     = {International anerkannte Blitzschutznormen : Ausgewogener und sicherer Schutz},
  publisher = {Fachhochschule Aachen},
  address   = {Aachen},
  year      = {2009},
  abstract  = {Die Einleitung zur Norm DIN EN 62305-3 beschreibt klar und ein - deutig: Der vorliegende Teil der IEC 62305 behandelt den Schutz von baulichen Anlagen gegen materielle Sch{\"a}den und den Schutz von Personen gegen Verletzungen durch Ber{\"u}hrungs- und Schrittspannungen. Als das wesentlichste und effektivste Mittel zum Schutz von baulichen Anlagen gegen materielle Sch{\"a}den gilt das Blitz - schutzsystem (LPS).},
  subject      = {Blitzschutz},
  language  = {de}
}
@article{HegerKock2004,
  author    = {Heger, Michael and Kock, Winfried},
  title     = {INGMEDIA, blended learning im Laborpraktikum. Ein hochschuldidaktisches Projekt},
  year      = {2004},
  abstract  = {Laborpraktika bieten Studierenden besondere Lernm{\"o}glichkeiten. Sie erleben im Praktikum mit Kopf (kognitiv), Herz (affektiv) und Hand (motorisch) Zusammenh{\"a}nge und Zusammenarbeit. Durch die multimediale Vorbereitung und Unterst{\"u}tzung der Laborpraktika mit INGMEDIA k{\"o}nnen diese Lernvorteile intensiver genutzt werden. Vielf{\"a}ltige und differenzierte Kontextangebote bieten individuelle Lerneinstiegsm{\"o}glichkeiten und aktivieren zu Selbstgesteuertem Lernen. Durch die Verbesserung von Vorwissen und Motivation er{\"o}ffnen scih Lehrenden und Lernenden neue Freir{\"a}ume bei der Gestaltung der Pr{\"a}senzveranstaltung. Durch hochschuldidaktische Aktionsforschung beim Einsatz im Lehrbetrieb wird die weitere Entwicklung von Software und Pr{\"a}senzveranstaltung prozesshaft begleitet.},
  language  = {de}
}
@article{JanusAchtsnichtTempeletal.2023,
  author    = {Janus, Kevin Alexander and Achtsnicht, Stefan and Tempel, Laura and Drinic, Aleksaner and Kopp, Alexander and Keusgen, Michael and Sch{\"o}ning, Michael Josef},
  title     = {Influence of fibroin membrane composition and curing parameters on the performance of a biodegradable enzymatic biosensor manufactured from Silicon-Free Carbon},
  series = {Physica status solidi : pss. A, Applications and materials science},
  volume    = {220},
  journal   = {Physica status solidi : pss. A, Applications and materials science},
  number    = {22},
  publisher = {Wiley-VCH},
  address   = {Weinheim},
  issn      = {1862-6300 (Print)},
  doi       = {10.1002/pssa.202300081},
  pages     = {Artikel 2300081},
  year      = {2023},
  abstract  = {Herein, fibroin, polylactide (PLA), and carbon are investigated for their suitability as biocompatible and biodegradable materials for amperometric biosensors. For this purpose, screen-printed carbon electrodes on the biodegradable substrates fibroin and PLA are modified with a glucose oxidase membrane and then encapsulated with the biocompatible material Ecoflex. The influence of different curing parameters of the carbon electrodes on the resulting biosensor characteristics is studied. The morphology of the electrodes is investigated by scanning electron microscopy, and the biosensor performance is examined by amperometric measurements of glucose (0.5-10 mM) in phosphate buffer solution, pH 7.4, at an applied potential of 1.2 V versus a Ag/AgCl reference electrode. Instead of Ecoflex, fibroin, PLA, and wound adhesive are tested as alternative encapsulation compounds: a series of swelling tests with different fibroin compositions, PLA, and Ecoflex has been performed before characterizing the most promising candidates by chronoamperometry. Therefore, the carbon electrodes are completely covered with the particular encapsulation material. Chronoamperometric measurements with H2O2 concentrations between 0.5 and 10 mM enable studying the leakage current behavior.},
  language  = {en}
}
@article{EggertKling2023,
  author    = {Eggert, Mathias and Kling, Rene},
  title     = {How to distribute charging requests of electronic vehicles? A reservation-based approach},
  series = {International Journal of Intelligent Transportation Systems Research},
  volume    = {21},
  journal   = {International Journal of Intelligent Transportation Systems Research},
  number    = {2023},
  publisher = {Springer},
  address   = {Berlin, Heidelberg, New York},
  issn      = {1868-8659},
  doi       = {10.1007/s13177-023-00367-z},
  pages     = {437 -- 460},
  year      = {2023},
  abstract  = {The number of electronic vehicles increase steadily while the space for extending the charging infrastructure is limited. In particular in urban areas, where parking spaces in attractive areas are famous, opportunities to setup new charging stations is very limited. This leads to an overload of some very attractive charging stations and an underutilization of less attractive ones. Against this background, the paper at hand presents the design of an e-vehicle reservation system that aims at distributing the utilization of the charging infrastructure, particularly in urban areas. By applying a design science approach, the requirements for a reservation-based utilization approach are elicited and a model for a suitable distribution approach and its instantiation are developed. The artefact is evaluated by simulating the distribution effects based on data of real charging station utilizations.},
  language  = {en}
}