@article{ZhenLiangStaatetal.2024,
  author    = {Zhen, Manghao and Liang, Yunpei and Staat, Manfred and Li, Quanqui and Li, Jianbo},
  title     = {Discontinuous fracture behaviors and constitutive model of sandstone specimens containing non-parallel prefabricated fissures under uniaxial compression},
  series = {Theoretical and Applied Fracture Mechanics},
  volume    = {131},
  journal   = {Theoretical and Applied Fracture Mechanics},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {0167-8442},
  doi       = {10.1016/j.tafmec.2024.104373},
  pages     = {Artikel 104373},
  year      = {2024},
  abstract  = {The deformation and damage laws of non-homogeneous irregular structural planes in rocks are the basis for studying the stability of rock engineering. To investigate the damage characteristics of rock containing non-parallel fissures, uniaxial compression tests and numerical simulations were conducted on sandstone specimens containing three non-parallel fissures inclined at 0°, 45° and 90° in this study. The characteristics of crack initiation and crack evolution of fissures with different inclinations were analyzed. A constitutive model for the discontinuous fractures of fissured sandstone was proposed. The results show that the fracture behaviors of fissured sandstone specimens are discontinuous. The stress-strain curves are non-smooth and can be divided into nonlinear crack closure stage, linear elastic stage, plastic stage and brittle failure stage, of which the plastic stage contains discontinuous stress drops. During the uniaxial compression test, the middle or ends of 0° fissures were the first to crack compared to 45° and 90° fissures. The end with small distance between 0° and 45° fissures cracked first, and the end with large distance cracked later. After the final failure, 0° fissures in all specimens were fractured, while 45° and 90° fissures were not necessarily fractured. Numerical simulation results show that the concentration of compressive stress at the tips of 0°, 45° and 90° fissures, as well as the concentration of tensile stress on both sides, decreased with the increase of the inclination angle. A constitutive model for the discontinuous fractures of fissured sandstone specimens was derived by combining the logistic model and damage mechanic theory. This model can well describe the discontinuous drops of stress and agrees well with the whole processes of the stress-strain curves of the fissured sandstone specimens.},
  language  = {en}
}
@article{WegmannHacklStaatetal.2016,
  author    = {Wegmann, Kilian and Hackl, Michael and Staat, Manfred and Mayer, Katharina and M{\"u}ller, Lars-Peter},
  title     = {Double plate osteosynthesis of proximal ulna fractures: biomechanical and clinical results},
  series = {Knee surgery, sports traumatology, arthroscopy},
  volume    = {Volume 24},
  journal   = {Knee surgery, sports traumatology, arthroscopy},
  number    = {Supplement 1},
  publisher = {Springer},
  address   = {Berlin},
  issn      = {0942-2056},
  doi       = {10.1007/s00167-016-4079-0},
  pages     = {58 -- 59},
  year      = {2016},
  abstract  = {While plate fixation of proximal ulna fractures might lead to superior clinical results compared to tension band wiring, regular plates represent an established risk factor for wound complications. The olecranon double plates (Medartis, Basel, CH) might decrease complications related to the osteosynthesis because of their low profile and better anatomical fit. This study aimed to evaluate the biomechanical performance and clinical results of the olecranon double plates.},
  language  = {en}
}
@article{VuStaat2004,
  author    = {Vu, Duc-Khoi and Staat, Manfred},
  title     = {An algorithm for shakedown analysis of structure with temperature dependent yield stress},
  year      = {2004},
  abstract  = {This work is an attempt to answer the question: How to use convex programming in shakedown analysis of structures made of materials with temperature-dependent properties. Based on recently established shakedown theorems and formulations, a dual relationship between upper and lower bounds of the shakedown limit load is found, an algorithmfor shakedown analysis is proposed. While the original problem is neither convex nor concave, the algorithm presented here has the advantage of employing convex programming tools.},
  subject      = {Einspielen <Werkstoff>},
  language  = {en}
}
@article{VuStaatTran2007,
  author    = {Vu, Duc Khoi and Staat, Manfred and Tran, Ich Thinh},
  title     = {Analysis of pressure equipment by application of the primal-dual theory of shakedown},
  series = {Communications in Numerical Methods in Engineering. 23 (2007), H. 3},
  journal   = {Communications in Numerical Methods in Engineering. 23 (2007), H. 3},
  isbn      = {1069-8299},
  pages     = {213 -- 225},
  year      = {2007},
  language  = {en}
}
@article{VuStaat2007,
  author    = {Vu, Duc Khoi and Staat, Manfred},
  title     = {Shakedown analysis of structures made of materials with temperature-dependent yield stress},
  series = {International Journal of Solids and Structures. 44 (2007), H. 13},
  journal   = {International Journal of Solids and Structures. 44 (2007), H. 13},
  isbn      = {0020-7683},
  pages     = {4524 -- 4540},
  year      = {2007},
  language  = {en}
}
@article{VantStaatBaroud2008,
  author    = {Vant, Christianne and Staat, Manfred and Baroud, Gamal},
  title     = {Percutaneous Vertebroplasty: A Review of Two Intraoperative Complications},
  series = {Bioengineering in Cell and Tissue Research / Artmann, Gerhard M. ; Chien, Shu (Eds.)},
  journal   = {Bioengineering in Cell and Tissue Research / Artmann, Gerhard M. ; Chien, Shu (Eds.)},
  publisher = {Springer},
  address   = {Berlin},
  isbn      = {978-3-540-75408-4},
  pages     = {527 -- 539},
  year      = {2008},
  language  = {en}
}
@article{UllrichGrottkeRossaintetal.2010,
  author    = {Ullrich, Sebastian and Grottke, Oliver and Rossaint, Rolf and Staat, Manfred and Deserno, Thomas M. and Kuhlen, Torsten},
  title     = {Virtual Needle Simulation with Haptics for Regional Anaesthesia},
  pages     = {1 -- 3},
  year      = {2010},
  language  = {en}
}
@article{TranStaat2010,
  author    = {Tran, Thanh Ngoc and Staat, Manfred},
  title     = {Shakedown analysis of two dimensional structures by an edge-based smoothed finite element method},
  pages     = {1 -- 7},
  year      = {2010},
  language  = {en}
}
@article{TranStaat2013,
  author    = {Tran, Thanh Ngoc and Staat, Manfred},
  title     = {An Edge-Based Smoothed Finite Element Method for Primal-Dual Shakedown Analysis of Structures Under Uncertainties},
  series = {Limit State of Materials and Structures : Direct Methods 2. Saxc{\´e}, G{\´e}ry de (Hrsg.)},
  journal   = {Limit State of Materials and Structures : Direct Methods 2. Saxc{\´e}, G{\´e}ry de (Hrsg.)},
  publisher = {Springer},
  address   = {Dordrecht},
  isbn      = {978-94-007-5424-9},
  pages     = {89 -- 102},
  year      = {2013},
  language  = {en}
}
@article{TranPhamVuetal.2009,
  author    = {Tran, Thanh Ngoc and Pham, Phu Tinh and Vu, D. K. and Staat, Manfred},
  title     = {Reliability Analysis of Inelastic Shell Structures Under Variable Loads},
  series = {Limit States of Materials and Structures : Direct Methods / Hrsg. Dieter Weichert; Hrsg. Alan Ponter},
  journal   = {Limit States of Materials and Structures : Direct Methods / Hrsg. Dieter Weichert; Hrsg. Alan Ponter},
  publisher = {Springer Netherland},
  address   = {Berlin},
  isbn      = {978-1-4020-9633-4},
  pages     = {135 -- 156},
  year      = {2009},
  language  = {en}
}
@article{TranKreissigVuetal.2008,
  author    = {Tran, Thanh Ngoc and Kreißig, R. and Vu, Duc Khoi and Staat, Manfred},
  title     = {Upper bound limit and shakedown analysis of shells using the exact Ilyushin yield surface},
  series = {Computer \& Structures. 86 (2008)},
  journal   = {Computer \& Structures. 86 (2008)},
  isbn      = {0045-7949},
  pages     = {1683 -- 1695},
  year      = {2008},
  language  = {en}
}
@article{TranKreissigStaat2009,
  author    = {Tran, Thanh Ngoc and Kreißig, R. and Staat, Manfred},
  title     = {Probabilistic limit and shakedown analysis of thin plates and shells},
  series = {Structural safety. 31 (2009), H. 1},
  journal   = {Structural safety. 31 (2009), H. 1},
  publisher = {-},
  isbn      = {0167-4730},
  pages     = {1 -- 18},
  year      = {2009},
  language  = {en}
}
@article{TranTrinhDaoetal.2022,
  author    = {Tran, Ngoc Trinh and Trinh, Tu Luc and Dao, Ngoc Tien and Giap, Van Tan and Truong, Manh Khuyen and Dinh, Thuy Ha and Staat, Manfred},
  title     = {FEM shakedown analysis of structures under random strength with chance constrained programming},
  series = {Vietnam Journal of Mechanics},
  volume    = {44},
  journal   = {Vietnam Journal of Mechanics},
  number    = {4},
  publisher = {Vietnam Academy of Science and Technology (VAST)},
  issn      = {0866-7136},
  doi       = {10.15625/0866-7136/17943},
  pages     = {459 -- 473},
  year      = {2022},
  abstract  = {Direct methods, comprising limit and shakedown analysis, are a branch of computational mechanics. They play a significant role in mechanical and civil engineering design. The concept of direct methods aims to determine the ultimate load carrying capacity of structures beyond the elastic range. In practical problems, the direct methods lead to nonlinear convex optimization problems with a large number of variables and constraints. If strength and loading are random quantities, the shakedown analysis can be formulated as stochastic programming problem. In this paper, a method called chance constrained programming is presented, which is an effective method of stochastic programming to solve shakedown analysis problems under random conditions of strength. In this study, the loading is deterministic, and the strength is a normally or lognormally distributed variable.},
  language  = {en}
}
@article{TranStaat2020,
  author    = {Tran, Ngoc Trinh and Staat, Manfred},
  title     = {Direct plastic structural design under lognormally distributed strength by chance constrained programming},
  series = {Optimization and Engineering},
  volume    = {21},
  journal   = {Optimization and Engineering},
  number    = {1},
  publisher = {Springer Nature},
  address   = {Cham},
  issn      = {1573-2924},
  doi       = {10.1007/s11081-019-09437-2},
  pages     = {131 -- 157},
  year      = {2020},
  abstract  = {We propose the so-called chance constrained programming model of stochastic programming theory to analyze limit and shakedown loads of structures under random strength with a lognormal distribution. A dual chance constrained programming algorithm is developed to calculate simultaneously both the upper and lower bounds of the plastic collapse limit and the shakedown limit. The edge-based smoothed finite element method (ES-FEM) is used with three-node linear triangular elements.},
  language  = {en}
}
@article{TranStaat2021,
  author    = {Tran, Ngoc Trinh and Staat, Manfred},
  title     = {Direct plastic structural design under random strength and random load by chance constrained programming},
  series = {European Journal of Mechanics - A/Solids},
  volume    = {85},
  journal   = {European Journal of Mechanics - A/Solids},
  number    = {Article 104106},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {0997-7538},
  doi       = {10.1016/j.euromechsol.2020.104106},
  year      = {2021},
  language  = {en}
}
@article{TopcuMadabhushiStaat2022,
  author    = {Top{\c{c}}u, Murat and Madabhushi, Gopal S.P. and Staat, Manfred},
  title     = {A generalized shear-lag theory for elastic stress transfer between matrix and fibres having a variable radius},
  series = {International Journal of Solids and Structures},
  volume    = {239-240},
  journal   = {International Journal of Solids and Structures},
  number    = {Art. No. 111464},
  publisher = {Elsevier},
  address   = {New York, NY},
  issn      = {0020-7683},
  doi       = {10.1016/j.ijsolstr.2022.111464},
  year      = {2022},
  abstract  = {A generalized shear-lag theory for fibres with variable radius is developed to analyse elastic fibre/matrix stress transfer. The theory accounts for the reinforcement of biological composites, such as soft tissue and bone tissue, as well as for the reinforcement of technical composite materials, such as fibre-reinforced polymers (FRP). The original shear-lag theory proposed by Cox in 1952 is generalized for fibres with variable radius and with symmetric and asymmetric ends. Analytical solutions are derived for the distribution of axial and interfacial shear stress in cylindrical and elliptical fibres, as well as conical and paraboloidal fibres with asymmetric ends. Additionally, the distribution of axial and interfacial shear stress for conical and paraboloidal fibres with symmetric ends are numerically predicted. The results are compared with solutions from axisymmetric finite element models. A parameter study is performed, to investigate the suitability of alternative fibre geometries for use in FRP.},
  language  = {en}
}
@article{StaatWoltersBongartsetal.1990,
  author    = {Staat, Manfred and Wolters, J and Bongarts, W. and Hennings, W. (u.a.)},
  title     = {{\"U}berarbeitete probabilistisch orientierte Sicherheitsanalyse f{\"u}r den HTR-Modul},
  series = {Jahrestagung Kerntechnik '90 / Kerntechnische Gesellschaft e.V. ; Deutsches Atomforum e.V},
  journal   = {Jahrestagung Kerntechnik '90 / Kerntechnische Gesellschaft e.V. ; Deutsches Atomforum e.V},
  publisher = {INFORUM},
  address   = {Bonn},
  pages     = {143 -- 146},
  year      = {1990},
  language  = {de}
}
@article{StaatVu2006,
  author    = {Staat, Manfred and Vu, Khoi Duc},
  title     = {Limit loads of circumferentially flawed pipes and cylindrical vessels under internal pressure},
  series = {International Journal of Pressure Vessels and Piping. 83 (2006), H. 3},
  journal   = {International Journal of Pressure Vessels and Piping. 83 (2006), H. 3},
  isbn      = {0308-0161},
  pages     = {188 -- 196},
  year      = {2006},
  language  = {en}
}
@article{StaatVu2004,
  author    = {Staat, Manfred and Vu, Duc-Khoi},
  title     = {An Algorithm for Shakedown Analysis for Materials with Temperature Dependent Yield Stress},
  series = {Proceedings in Applied Mathematics and Mechanics (PAMM). 4 (2004), H. 1},
  journal   = {Proceedings in Applied Mathematics and Mechanics (PAMM). 4 (2004), H. 1},
  isbn      = {1617-7061},
  pages     = {231 -- 233},
  year      = {2004},
  language  = {en}
}
@article{StaatVu2007,
  author    = {Staat, Manfred and Vu, Duc-Khoi},
  title     = {Limit analysis of flaws in pressurized pipes and cylindrical vessels. Part I: Axial defects},
  series = {Engineering Fracture Mechanics. 74 (2007), H. 3},
  journal   = {Engineering Fracture Mechanics. 74 (2007), H. 3},
  isbn      = {0013-7944},
  pages     = {431 -- 450},
  year      = {2007},
  language  = {en}
}
@article{StaatVu2012,
  author    = {Staat, Manfred and Vu, Duc Khoi},
  title     = {Limit analysis of flaws in pressurized pipes and cylindrical vessels Part II: Circumferential defects},
  series = {Engineering Fracture Mechanics ; 97(2013), H. 1},
  volume    = {97},
  journal   = {Engineering Fracture Mechanics ; 97(2013), H. 1},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {0013-7944},
  doi       = {10.1016/j.engfracmech.2012.05.017},
  pages     = {314 -- 333},
  year      = {2012},
  abstract  = {Upper and lower bound theorems of limit analyses have been presented in part I of the paper. Part II starts with the finite element discretization of these theorems and demonstrates how both can be combined in a primal-dual optimization problem. This recently proposed numerical method is used to guide the development of a new class of closed-form limit loads for circumferential defects, which show that only large defects contribute to plastic collapse with a rapid loss of strength with increasing crack sizes. The formulae are compared with primal-dual FEM limit analyses and with burst tests. Even closer predictions are obtained with iterative limit load solutions for the von Mises yield function and for the Tresca yield function. Pressure loading of the faces of interior cracks in thick pipes reduces the collapse load of circumferential defects more than for axial flaws. Axial defects have been treated in part I of the paper.},
  language  = {en}
}
@article{StaatTrenzLohmannetal.2012,
  author    = {Staat, Manfred and Trenz, Eva and Lohmann, Philipp and Frotscher, Ralf and Klinge, Uwe and Tabaza, Ruth and Kirschner-Hermanns, Ruth},
  title     = {New measurements to compare soft tissue anchoring systems in pelvic floor surgery},
  series = {Journal of Biomedical Materials Research Part B: Applied Biomaterials},
  volume    = {100B},
  journal   = {Journal of Biomedical Materials Research Part B: Applied Biomaterials},
  number    = {4},
  publisher = {Wiley},
  address   = {Hoboken, NJ},
  issn      = {1552-4981},
  doi       = {10.1002/jbm.b.32654},
  pages     = {924 -- 933},
  year      = {2012},
  abstract  = {Suburethral slings as well as different meshes are widely used treating stress urinary incontinence and prolaps in women. With the development of MiniSlings and special meshes using less alloplastic material anchorage systems become more important to keep devices in place and to put some tension especially on the MiniSlings. To date, there are many different systems of MiniSlings of different companies on the market which differ in the structure of the used meshes and anchors. A new objective measurement method to compare different properties of MiniSling systems (mesh and anchor) is presented in this article. Ballistic gelatine acts as soft tissue surrogate. Significant differences in parameters like pull-out strength of anchors or shrinkage of meshes under loading conditions have been determined. The form and size of the anchors as well as the structural stability of the meshes are decisive for a proper integration. The tested anchorings sytems showed markedly different mechanical function at their respective load bearing capacity. As the stable fixation of the device in tissue is a prerequisite for a permanet reinforcement, the proposed test system permits further optimisation of anchor and mesh devices to improve the success of the surgical treatment},
  language  = {en}
}
@article{StaatTranKreissig2008,
  author    = {Staat, Manfred and Tran, Thanh Ngoc and Kreißig, R.},
  title     = {Load bearing capacity of thin shell structures made of elastoplastic material by direct methods},
  series = {Technische Mechanik. 28 (2008), H. 3-4},
  journal   = {Technische Mechanik. 28 (2008), H. 3-4},
  pages     = {299 -- 309},
  year      = {2008},
  language  = {en}
}
@article{StaatSponagelNguyen2010,
  author    = {Staat, Manfred and Sponagel, Stefan and Nguyen, Nhu Huynh},
  title     = {Experiment and material model for soft tissue materials},
  series = {Constitutive models for rubber VI : proceedings of the sixth European Conference on Constitutive Models for Rubber, Dresden, Germany, 7 - 10 September 2009 / eds. Gert Heinrich ...},
  journal   = {Constitutive models for rubber VI : proceedings of the sixth European Conference on Constitutive Models for Rubber, Dresden, Germany, 7 - 10 September 2009 / eds. Gert Heinrich ...},
  publisher = {CRC Press},
  address   = {Boca Raton [u.a.]},
  isbn      = {978-0-415-56327-7},
  pages     = {465 -- 470},
  year      = {2010},
  language  = {en}
}
@article{StaatSchwartzLangetal.2003,
  author    = {Staat, Manfred and Schwartz, M. and Lang, H. and Wirtz, K. and Heitzer, M.},
  title     = {Design by Analysis of Pressure Components by non-linear Optimization},
  series = {The 10th International Conference on Pressure Vessel Technology, July 7-10, 2003, Vienna, Austria, Proceedings ICPVT-10 / Zeman, J. L. [ed]},
  journal   = {The 10th International Conference on Pressure Vessel Technology, July 7-10, 2003, Vienna, Austria, Proceedings ICPVT-10 / Zeman, J. L. [ed]},
  publisher = {{\"O}GS, {\"O}sterreichische Gesellschaft f{\"u}r Schweißtechnik},
  address   = {Wien},
  isbn      = {3950152814},
  pages     = {59 -- 65},
  year      = {2003},
  language  = {en}
}
@article{StaatKuehnHaugeretal.2004,
  author    = {Staat, Manfred and K{\"u}hn, R. and Hauger, W. and Sponagel, Stefan},
  title     = {An Interpretation of Wolff's Law},
  series = {Biomedizinische Technik. 49 (2004)},
  journal   = {Biomedizinische Technik. 49 (2004)},
  isbn      = {0932-4666},
  pages     = {1020 -- 1021},
  year      = {2004},
  language  = {de}
}
@article{StaatHeitzerReinersetal.2003,
  author    = {Staat, Manfred and Heitzer, M. and Reiners, H. and Schubert, F.},
  title     = {Shakedown and ratchetting under tension-torsion loadings: analysis and experiments},
  series = {Nuclear Engineering and Design. 225 (2003), H. 1},
  journal   = {Nuclear Engineering and Design. 225 (2003), H. 1},
  isbn      = {0029-5493},
  pages     = {11 -- 26},
  year      = {2003},
  language  = {en}
}
@article{StaatHeitzerLangetal.2005,
  author    = {Staat, Manfred and Heitzer, M. and Lang, H. and Wirtz, K.},
  title     = {Direct Finite Element Route for Design-by-Analysis of Pressure Components},
  series = {International Journal of Pressure Vessels and Piping. 82 (2005), H. 1},
  journal   = {International Journal of Pressure Vessels and Piping. 82 (2005), H. 1},
  isbn      = {0308-0161},
  pages     = {61 -- 67},
  year      = {2005},
  language  = {en}
}
@article{StaatHeitzerHicken1998,
  author    = {Staat, Manfred and Heitzer, M. and Hicken, E.F.},
  title     = {LISA, ein europ{\"a}isches Projekt zur direkten Berechnung der Tragf{\"a}higkeit duktiler Strukturen.},
  year      = {1998},
  language  = {de}
}
@article{StaatHeitzer1997,
  author    = {Staat, Manfred and Heitzer, M.},
  title     = {Limit and Shakedown Analysis for Plastic Safety of Complex Structures},
  series = {Transactions of the 14th International Conference on Structural Dynamics in Reactor Technology (SMiRT-14) / Livolant, M. [ed]},
  journal   = {Transactions of the 14th International Conference on Structural Dynamics in Reactor Technology (SMiRT-14) / Livolant, M. [ed]},
  address   = {Lyon},
  pages     = {33 -- 40},
  year      = {1997},
  language  = {en}
}
@article{StaatHeitzer1997,
  author    = {Staat, Manfred and Heitzer, M.},
  title     = {Limit and Shakedown Analysis Using a General Purpose Finite Element Code},
  series = {Proceedings of NAFEMS World Congress '97 on Design, Simulation \& Optimisation : reliability \& applicability of computational methods ; Stuttgart, Germany, 9 - 11 April 1997},
  journal   = {Proceedings of NAFEMS World Congress '97 on Design, Simulation \& Optimisation : reliability \& applicability of computational methods ; Stuttgart, Germany, 9 - 11 April 1997},
  publisher = {NAFEMS},
  address   = {Glasgow},
  isbn      = {1-87437-620-4},
  pages     = {522 -- 533},
  year      = {1997},
  language  = {en}
}
@article{StaatHeitzer2000,
  author    = {Staat, Manfred and Heitzer, M.},
  title     = {Traglastanalyse - ein strukturmechanisches Verfahren zur Beurteilung von gerissenen Bauteilen und Verbindungen},
  series = {Festigkeits- und Bruchverhalten von F{\"u}geverbindungen : 32. Tagung des DVM-Arbeitskreises Bruchvorg{\"a}nge ; 22. und 23. Februar 2000 in Berlin / Richard, H. A. [Hrsg]},
  journal   = {Festigkeits- und Bruchverhalten von F{\"u}geverbindungen : 32. Tagung des DVM-Arbeitskreises Bruchvorg{\"a}nge ; 22. und 23. Februar 2000 in Berlin / Richard, H. A. [Hrsg]},
  publisher = {Deutscher Verband f{\"u}r Materialforschung und -pr{\"u}fung},
  address   = {Berlin},
  pages     = {183 -- 192},
  year      = {2000},
  language  = {de}
}
@article{StaatHeitzer2000,
  author    = {Staat, Manfred and Heitzer, M.},
  title     = {Reliability Analysis of Elasto-Plastic Structures under Variable Loads},
  series = {Inelastic analysis of structures under variable loads : theory and engineering applications / Maier, G.; Weichert, D. [ed]},
  journal   = {Inelastic analysis of structures under variable loads : theory and engineering applications / Maier, G.; Weichert, D. [ed]},
  publisher = {Kluwer Academic Publ.},
  address   = {Dordrecht},
  isbn      = {0-7923-6645-X},
  pages     = {269 -- 288},
  year      = {2000},
  language  = {en}
}
@article{StaatHeitzer2000,
  author    = {Staat, Manfred and Heitzer, M.},
  title     = {Direct FEM approach to design-by-analysis of pressurized components},
  series = {Achema 2000 : Sonderausgabe / Linde. [Hrsg.: Linde AG. Red.: Volker R. Leski]},
  journal   = {Achema 2000 : Sonderausgabe / Linde. [Hrsg.: Linde AG. Red.: Volker R. Leski]},
  publisher = {Linde AG},
  address   = {Wiesbaden},
  pages     = {79 -- 81},
  year      = {2000},
  language  = {de}
}
@article{StaatHeitzer1999,
  author    = {Staat, Manfred and Heitzer, M.},
  title     = {Structural Reliability Analysis of Elasto-Plastic Structures},
  series = {Safety and reliability : proceedings of ESREL '99, the Tenth European Conference on Safety and Reliability, Munich-Garching, Germany, 13 - 17 September 1999 / Schu{\"e}ller, G. I.; Kafka, P. [eds]},
  journal   = {Safety and reliability : proceedings of ESREL '99, the Tenth European Conference on Safety and Reliability, Munich-Garching, Germany, 13 - 17 September 1999 / Schu{\"e}ller, G. I.; Kafka, P. [eds]},
  publisher = {Balkema},
  address   = {Rotterdam},
  isbn      = {90-5809-109-0},
  pages     = {513 -- 518},
  year      = {1999},
  language  = {en}
}
@article{StaatHeitzer2002,
  author    = {Staat, Manfred and Heitzer, M.},
  title     = {Limit and Shakedown Analysis with Uncertain Data},
  series = {Stochastic optimization techniques : numerical methods and technical applications / Marti, K. [ed]},
  journal   = {Stochastic optimization techniques : numerical methods and technical applications / Marti, K. [ed]},
  publisher = {Springer},
  address   = {Heidelberg},
  isbn      = {3-540-42889-5},
  pages     = {241 -- 254},
  year      = {2002},
  language  = {en}
}
@article{StaatHeitzer2003,
  author    = {Staat, Manfred and Heitzer, M.},
  title     = {Probabilistic limit and shakedown problems},
  series = {Numerical Methods for Limit and Shakedown Analysis. Deterministic and Probabilistic Approach. NIC Series Vol. 15 / Ed. by Staat, M; Heitzer, M.},
  journal   = {Numerical Methods for Limit and Shakedown Analysis. Deterministic and Probabilistic Approach. NIC Series Vol. 15 / Ed. by Staat, M; Heitzer, M.},
  publisher = {John von Neumann Institute for Computing (NIC)},
  address   = {J{\"u}lich},
  isbn      = {3-00-010001-6},
  pages     = {217 -- 268},
  year      = {2003},
  language  = {en}
}
@article{StaatHeitzer1999,
  author    = {Staat, Manfred and Heitzer, M.},
  title     = {FEM-computation of load carrying capacity of highly loaded passive components by direct methods. Heitzer, M. ; Staat, M.},
  series = {Nuclear Engineering and Design. 193 (1999), H. 3},
  journal   = {Nuclear Engineering and Design. 193 (1999), H. 3},
  isbn      = {0029-5493},
  pages     = {349 -- 358},
  year      = {1999},
  language  = {en}
}
@article{StaatFioriniLensaetal.1997,
  author    = {Staat, Manfred and Fiorini, G. L. and Lensa, W. von and Burgazzi, L.},
  title     = {Reliability Methods for Passive Safety Functions},
  series = {Proceedings of the SMiRT 14 Post Conference Seminar No 18 on Passive Safety Features in Nuclear Installations},
  journal   = {Proceedings of the SMiRT 14 Post Conference Seminar No 18 on Passive Safety Features in Nuclear Installations},
  address   = {Pisa},
  year      = {1997},
  language  = {en}
}
@article{StaatBaroudTopcuetal.2008,
  author    = {Staat, Manfred and Baroud, G. and Topcu, M. and Sponagel, Stefan},
  title     = {Soft Materials in Technology and Biology - Characteristics, Properties, and Parameter Identification},
  series = {Bioengineering in Cell and Tissue Research / Artmann, Gerhard M. ; Chien, Shu (Eds.)},
  journal   = {Bioengineering in Cell and Tissue Research / Artmann, Gerhard M. ; Chien, Shu (Eds.)},
  publisher = {Springer},
  address   = {Berlin},
  isbn      = {978-3-540-75408-4},
  pages     = {253 -- 315},
  year      = {2008},
  language  = {en}
}
@article{StaatBallmann1988,
  author    = {Staat, Manfred and Ballmann, J.},
  title     = {Computation of impacts on elastic solids by methods of bicharacteristics},
  series = {Computational Mechanics '88 : theory and applications ; proceedings of the International Conference on Computational Engineering Science April 10-14, 1988, Atlanta, GA, USA ; vol. 2},
  journal   = {Computational Mechanics '88 : theory and applications ; proceedings of the International Conference on Computational Engineering Science April 10-14, 1988, Atlanta, GA, USA ; vol. 2},
  pages     = {1719 -- 1722},
  year      = {1988},
  abstract  = {Shock waves, explosions, impacts or cavitation bubble collapses may generate stress waves in solids causing cracks or unexpected dammage due to focussing, physical nonlinearity or interaction with existing cracks. There is a growing interest in wave propagation, which poses many novel problems to experimentalists and theorists.},
  subject      = {Bicharakteristikenverfahren},
  language  = {en}
}
@article{StaatBallmann1989,
  author    = {Staat, Manfred and Ballmann, J.},
  title     = {Zur Problematik tensorieller Verallgemeinerungen einachsiger nichtlinearer Materialgesetze},
  series = {Zeitschrift f{\"u}r angewandte Mathematik und Mechanik : ZAMM. 69 (1989), H. 2},
  journal   = {Zeitschrift f{\"u}r angewandte Mathematik und Mechanik : ZAMM. 69 (1989), H. 2},
  isbn      = {0946-8463},
  doi       = {10.1515/9783112553169-006},
  pages     = {73 -- 81},
  year      = {1989},
  language  = {de}
}
@article{StaatBallmann1988,
  author    = {Staat, Manfred and Ballmann, J.},
  title     = {Wave Propagation and Focussing in Plates},
  series = {Impact loading and dynamic behaviour of materials : Papers presented at the International Conference on Impact Loading and Dynamic Behaviour of Materials, Vol. 2 / Chiem, C. Y.; Kunze, L. (u.a.) [eds]},
  journal   = {Impact loading and dynamic behaviour of materials : Papers presented at the International Conference on Impact Loading and Dynamic Behaviour of Materials, Vol. 2 / Chiem, C. Y.; Kunze, L. (u.a.) [eds]},
  publisher = {DGM Informationsges.},
  address   = {Oberursel},
  year      = {1988},
  language  = {en}
}
@article{StaatBallmann1985,
  author    = {Staat, Manfred and Ballmann, J.},
  title     = {Anisotrope Ausbreitung und Fokussierung von Beschleunigungswellen in vorgespannten nichtlinearelastischen Scheiben},
  series = {Wellenfokussierung, Kolloquium des SFB 27, RWTH Aachen},
  journal   = {Wellenfokussierung, Kolloquium des SFB 27, RWTH Aachen},
  address   = {Aachen},
  pages     = {140 -- 158},
  year      = {1985},
  language  = {de}
}
@article{Staat1996,
  author    = {Staat, Manfred},
  title     = {Problems and Chances for Probabilistic Fracture Mechanics in the Analysis of Steel Pressure Boundary Reliability},
  series = {Technical feasibility and reliability of passive safety systems for nuclear power plants. Proceedings of an Advisory Group Meeting held in J{\"u}lich, 21-24 November 1994},
  journal   = {Technical feasibility and reliability of passive safety systems for nuclear power plants. Proceedings of an Advisory Group Meeting held in J{\"u}lich, 21-24 November 1994},
  address   = {Vienna},
  pages     = {43 -- 55},
  year      = {1996},
  language  = {en}
}
@article{Staat1993,
  author    = {Staat, Manfred},
  title     = {Sensitivity of and Influences on the Reliability of an HTR-Module Primary Circuit Pressure Boundary},
  series = {Transactions of the 12th International Conference on Structural Mechanics in Reactor Technology (SMiRT-12) / Kussmaul, K. [ed]},
  journal   = {Transactions of the 12th International Conference on Structural Mechanics in Reactor Technology (SMiRT-12) / Kussmaul, K. [ed]},
  publisher = {Elsevier},
  address   = {Amsterdam},
  isbn      = {0-444-81515-5},
  pages     = {147 -- 152},
  year      = {1993},
  language  = {en}
}
@article{Staat1993,
  author    = {Staat, Manfred},
  title     = {Reliability of the Primary Circuit Pressure Boundary of an HTR-Module under Accident Conditions},
  series = {Safety and reliability assessment : an integral approach ; ESREL'93 ; proceedings of the European Safety and Reliability Conference, Munich, Germany, May 10th - 12th 1993 / Kafka, P. [ed]},
  journal   = {Safety and reliability assessment : an integral approach ; ESREL'93 ; proceedings of the European Safety and Reliability Conference, Munich, Germany, May 10th - 12th 1993 / Kafka, P. [ed]},
  publisher = {Elsevier},
  address   = {Amsterdam},
  isbn      = {0-444-81561-9},
  pages     = {331 -- 342},
  year      = {1993},
  language  = {en}
}
@article{Staat1992,
  author    = {Staat, Manfred},
  title     = {Probabilistische Bewertung des bruchmechanischen Verhaltens der Prim{\"a}rkreisdruckumschließung eines HTR-Moduls},
  year      = {1992},
  language  = {de}
}
@article{Staat1991,
  author    = {Staat, Manfred},
  title     = {Versagenswahrscheinlichkeit der Prim{\"a}rkreisdruckumschließung eines HTR-Moduls zur Prozeßw{\"a}rmegewinnung unter St{\"o}rfallbedingungen bei verschiedenen Versagensmoden},
  year      = {1991},
  language  = {de}
}
@article{Staat2002,
  author    = {Staat, Manfred},
  title     = {Some Achievements of the European Project LISA for FEM Based Limit and Shakedown Analysis},
  series = {Computational mechanics : developments and applications, 2002 : presented at the 2002 ASME Pressure Vessels and Piping Conference, Vancouver, British Columbia, Canada, August 5 - 9. / Badie, N. [ed]},
  journal   = {Computational mechanics : developments and applications, 2002 : presented at the 2002 ASME Pressure Vessels and Piping Conference, Vancouver, British Columbia, Canada, August 5 - 9. / Badie, N. [ed]},
  publisher = {American Society of Mechanical Engineers},
  address   = {New York},
  isbn      = {0791846520},
  pages     = {177 -- 185},
  year      = {2002},
  language  = {en}
}