@inproceedings{NiederwestbergSchneiderTeixeiraBouraetal.2022,
  author    = {Niederwestberg, Stefan and Schneider, Falko and Teixeira Boura, Cristiano Jos{\´e} and Herrmann, Ulf},
  title     = {Introduction to a direct irradiated transparent tube particle receiver},
  series = {SOLARPACES 2020},
  booktitle = {SOLARPACES 2020},
  number    = {2445 / 1},
  publisher = {AIP conference proceedings / American Institute of Physics},
  address   = {Melville, NY},
  isbn      = {978-0-7354-4195-8},
  issn      = {1551-7616 (online)},
  doi       = {10.1063/5.0086735},
  pages     = {9 Seiten},
  year      = {2022},
  abstract  = {New materials often lead to innovations and advantages in technical applications. This also applies to the particle receiver proposed in this work that deploys high-temperature and scratch resistant transparent ceramics. With this receiver design, particles are heated through direct-contact concentrated solar irradiance while flowing downwards through tubular transparent ceramics from top to bottom. In this paper, the developed particle receiver as well as advantages and disadvantages are described. Investigations on the particle heat-up characteristics from solar irradiance were carried out with DEM simulations which indicate that particle temperatures can reach up to 1200 K. Additionally, a simulation model was set up for investigating the dynamic behavior. A test receiver at laboratory scale has been designed and is currently being built. In upcoming tests, the receiver test rig will be used to validate the simulation results. The design and the measurement equipment is described in this work.},
  language  = {en}
}
@article{GoettenFingerHavermannetal.2021,
  author    = {G{\"o}tten, Falk and Finger, Felix and Havermann, Marc and Braun, Carsten and Marino, M. and Bil, C.},
  title     = {Full configuration drag estimation of short-to-medium range fixed-wing UAVs and its impact on initial sizing optimization},
  series = {CEAS Aeronautical Journal},
  volume    = {12},
  journal   = {CEAS Aeronautical Journal},
  publisher = {Springer},
  address   = {Berlin},
  issn      = {1869-5590 (Online)},
  doi       = {10.1007/s13272-021-00522-w},
  pages     = {589 -- 603},
  year      = {2021},
  abstract  = {The paper presents the derivation of a new equivalent skin friction coefficient for estimating the parasitic drag of short-to-medium range fixed-wing unmanned aircraft. The new coefficient is derived from an aerodynamic analysis of ten different unmanned aircraft used for surveillance, reconnaissance, and search and rescue missions. The aircraft is simulated using a validated unsteady Reynolds-averaged Navier Stokes approach. The UAV's parasitic drag is significantly influenced by the presence of miscellaneous components like fixed landing gears or electro-optical sensor turrets. These components are responsible for almost half of an unmanned aircraft's total parasitic drag. The new equivalent skin friction coefficient accounts for these effects and is significantly higher compared to other aircraft categories. It is used to initially size an unmanned aircraft for a typical reconnaissance mission. The improved parasitic drag estimation yields a much heavier unmanned aircraft when compared to the sizing results using available drag data of manned aircraft.},
  language  = {en}
}
@inproceedings{GoettenFingerBraunetal.2019,
  author    = {G{\"o}tten, Falk and Finger, Felix and Braun, Carsten and Havermann, Marc and Bil, C. and Gomez, F.},
  title     = {Empirical Correlations for Geometry Build-Up of Fixed Wing Unmanned Air Vehicles},
  series = {APISAT 2018: The Proceedings of the 2018 Asia-Pacific International Symposium on Aerospace Technology (APISAT 2018)},
  booktitle = {APISAT 2018: The Proceedings of the 2018 Asia-Pacific International Symposium on Aerospace Technology (APISAT 2018)},
  publisher = {Springer},
  address   = {Singapore},
  isbn      = {978-981-13-3305-7},
  doi       = {10.1007/978-981-13-3305-7_109},
  pages     = {1365 -- 1381},
  year      = {2019},
  abstract  = {The results of a statistical investigation of 42 fixed-wing, small to medium sized (20 kg-1000 kg) reconnaissance unmanned air vehicles (UAVs) are presented. Regression analyses are used to identify correlations of the most relevant geometry dimensions with the UAV's maximum take-off mass. The findings allow an empirical based geometry-build up for a complete unmanned aircraft by referring to its take-off mass only. This provides a bridge between very early design stages (initial sizing) and the later determination of shapes and dimensions. The correlations might be integrated into a UAV sizing environment and allow designers to implement more sophisticated drag and weight estimation methods in this process. Additional information on correlation factors for a rough drag estimation methodology indicate how this technique can significantly enhance the accuracy of early design iterations.},
  language  = {en}
}
@inproceedings{NeumannAdamBackesetal.2021,
  author    = {Neumann, Hannah and Adam, Mario and Backes, Klaus and B{\"o}rner, Martin and Clees, Tanja and Doetsch, Christian and Glaeser, Susanne and Herrmann, Ulf and May, Johanna and Rosenthal, Florian and Sauer, Dirk Uwe and Stadler, Ingo},
  title     = {Development of open educational resources for renewable energy and the energy transition process},
  series = {ISES SWC 2021},
  booktitle = {ISES SWC 2021},
  publisher = {International Solar Energy Society},
  address   = {Freiburg},
  doi       = {10.18086/swc.2021.47.03},
  pages     = {6 Seiten},
  year      = {2021},
  abstract  = {The dissemination of knowledge about renewable energies is understood as a social task with the highest topicality. The transfer of teaching content on renewable energies into digital open educational resources offers the opportunity to significantly accelerate the implementation of the energy transition. Thus, in the here presented project six German universities create open educational resources for the energy transition. These materials are available to the public on the internet under a free license. So far there has been no publicly accessible, editable media that cover entire learning units about renewable energies extensively and in high technical quality. Thus, in this project, the content that remains up-to-date for a longer period is appropriately prepared in terms of media didactics. The materials enable lecturers to provide students with in-depth training about technologies for the energy transition. In a particular way, the created material is also suitable for making the general public knowledgeable about the energy transition with scientifically based material.},
  language  = {en}
}
@inproceedings{SchwagerAngeleSchwarzboezletal.2023,
  author    = {Schwager, Christian and Angele, Florian and Schwarzb{\"o}zl, Peter and Teixeira Boura, Cristiano Jos{\´e} and Herrmann, Ulf},
  title     = {Model predictive assistance for operational decision making in molten salt receiver systems},
  series = {SolarPACES: Solar Power \& Chemical Energy Systems},
  booktitle = {SolarPACES: Solar Power \& Chemical Energy Systems},
  number    = {2815 / 1},
  publisher = {AIP conference proceedings / American Institute of Physics},
  address   = {Melville, NY},
  isbn      = {978-0-7354-4623-6},
  issn      = {1551-7616 (online)},
  doi       = {10.1063/5.0151514},
  pages     = {8 Seiten},
  year      = {2023},
  abstract  = {Despite the challenges of pioneering molten salt towers (MST), it remains the leading technology in central receiver power plants today, thanks to cost effective storage integration and high cost reduction potential. The limited controllability in volatile solar conditions can cause significant losses, which are difficult to estimate without comprehensive modeling [1]. This paper presents a Methodology to generate predictions of the dynamic behavior of the receiver system as part of an operating assistance system (OAS). Based on this, it delivers proposals if and when to drain and refill the receiver during a cloudy period in order maximize the net yield and quantifies the amount of net electricity gained by this. After prior analysis with a detailed dynamic two-phase model of the entire receiver system, two different reduced modeling approaches where developed and implemented in the OAS. A tailored decision algorithm utilizes both models to deliver the desired predictions efficiently and with appropriate accuracy.},
  language  = {en}
}
@inproceedings{SchwagerAngeleNourietal.2022,
  author    = {Schwager, Christian and Angele, Florian and Nouri, Bijan and Schwarzb{\"o}zl, Peter and Teixeira Boura, Cristiano Jos{\´e} and Herrmann, Ulf},
  title     = {Impact of DNI forecast quality on performance prediction for a commercial scale solar tower: Application of nowcasting DNI maps to dynamic solar tower simulation},
  series = {SolarPACES 2022 conference proceedings},
  booktitle = {SolarPACES 2022 conference proceedings},
  number    = {1},
  publisher = {TIB Open Publishing},
  address   = {Hannover},
  issn      = {2751-9899 (online)},
  doi       = {10.52825/solarpaces.v1i.675},
  pages     = {9 Seiten},
  year      = {2022},
  abstract  = {Concerning current efforts to improve operational efficiency and to lower overall costs of concentrating solar power (CSP) plants with prediction-based algorithms, this study investigates the quality and uncertainty of nowcasting data regarding the implications for process predictions. DNI (direct normal irradiation) maps from an all-sky imager-based nowcasting system are applied to a dynamic prediction model coupled with ray tracing. The results underline the need for high-resolution DNI maps in order to predict net yield and receiver outlet temperature realistically. Furthermore, based on a statistical uncertainty analysis, a correlation is developed, which allows for predicting the uncertainty of the net power prediction based on the corresponding DNI forecast uncertainty. However, the study reveals significant prediction errors and the demand for further improvement in the accuracy at which local shadings are forecasted.},
  language  = {en}
}
@inproceedings{SchulteSchwagerFrantzetal.2022,
  author    = {Schulte, Jonas and Schwager, Christian and Frantz, Cathy and Schloms, Felix and Teixeira Boura, Cristiano Jos{\´e} and Herrmann, Ulf},
  title     = {Control concept for a molten salt receiver in star design: Development, optimization and testing with cloud passage scenarios},
  series = {SolarPACES 2022 conference proceedings},
  booktitle = {SolarPACES 2022 conference proceedings},
  number    = {1},
  publisher = {TIB Open Publishing},
  address   = {Hannover},
  issn      = {2751-9899 (online)},
  doi       = {10.52825/solarpaces.v1i.693},
  pages     = {9 Seiten},
  year      = {2022},
  abstract  = {A promising approach to reduce the system costs of molten salt solar receivers is to enable the irradiation of the absorber tubes on both sides. The star design is an innovative receiver design, pursuing this approach. The unconventional design leads to new challenges in controlling the system. This paper presents a control concept for a molten salt receiver system in star design. The control parameters are optimized in a defined test cycle by minimizing a cost function. The control concept is tested in realistic cloud passage scenarios based on real weather data. During these tests, the control system showed no sign of unstable behavior, but to perform sufficiently in every scenario further research and development like integrating Model Predictive Controls (MPCs) need to be done. The presented concept is a starting point to do so.},
  language  = {en}
}
@inproceedings{LahrsKrisamHerrmann2023,
  author    = {Lahrs, Lennart and Krisam, Pierre and Herrmann, Ulf},
  title     = {Envisioning a collaborative energy system planning platform for the energy transition at the district level},
  series = {ECOS 2023. The 36th International Conference on Efficiency, Cost, Optimization, Simulation and Environmental Impact of Energy Systems},
  booktitle = {ECOS 2023. The 36th International Conference on Efficiency, Cost, Optimization, Simulation and Environmental Impact of Energy Systems},
  publisher = {Procedings of ECOS 2023},
  doi       = {10.52202/069564-0284},
  pages     = {3163 -- 3170},
  year      = {2023},
  abstract  = {Residential and commercial buildings account for more than one-third of global energy-related greenhouse gas emissions. Integrated multi-energy systems at the district level are a promising way to reduce greenhouse gas emissions by exploiting economies of scale and synergies between energy sources. Planning district energy systems comes with many challenges in an ever-changing environment. Computational modelling established itself as the state-of-the-art method for district energy system planning. Unfortunately, it is still cumbersome to combine standalone models to generate insights that surpass their original purpose. Ideally, planning processes could be solved by using modular tools that easily incorporate the variety of competing and complementing computational models. Our contribution is a vision for a collaborative development and application platform for multi-energy system planning tools at the district level. We present challenges of district energy system planning identified in the literature and evaluate whether this platform can help to overcome these challenges. Further, we propose a toolkit that represents the core technical elements of the platform. Lastly, we discuss community management and its relevance for the success of projects with collaboration and knowledge sharing at their core.},
  language  = {en}
}
@article{SchwagerFleschSchwarzboezletal.2022,
  author    = {Schwager, Christian and Flesch, Robert and Schwarzb{\"o}zl, Peter and Herrmann, Ulf and Teixeira Boura, Cristiano Jos{\´e}},
  title     = {Advanced two phase flow model for transient molten salt receiver system simulation},
  series = {Solar Energy},
  volume    = {232},
  journal   = {Solar Energy},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {0038-092X (print)},
  doi       = {10.1016/j.solener.2021.12.065},
  pages     = {362 -- 375},
  year      = {2022},
  abstract  = {In order to realistically predict and optimize the actual performance of a concentrating solar power (CSP) plant sophisticated simulation models and methods are required. This paper presents a detailed dynamic simulation model for a Molten Salt Solar Tower (MST) system, which is capable of simulating transient operation including detailed startup and shutdown procedures including drainage and refill. For appropriate representation of the transient behavior of the receiver as well as replication of local bulk and surface temperatures a discretized receiver model based on a novel homogeneous two-phase (2P) flow modelling approach is implemented in Modelica Dymola®. This allows for reasonable representation of the very different hydraulic and thermal properties of molten salt versus air as well as the transition between both. This dynamic 2P receiver model is embedded in a comprehensive one-dimensional model of a commercial scale MST system and coupled with a transient receiver flux density distribution from raytracing based heliostat field simulation. This enables for detailed process prediction with reasonable computational effort, while providing data such as local salt film and wall temperatures, realistic control behavior as well as net performance of the overall system. Besides a model description, this paper presents some results of a validation as well as the simulation of a complete startup procedure. Finally, a study on numerical simulation performance and grid dependencies is presented and discussed.},
  language  = {en}
}
@inproceedings{BroennerHoefkenSchuba2016,
  author    = {Broenner, Simon and H{\"o}fken, Hans-Wilhelm and Schuba, Marko},
  title     = {Streamlining extraction and analysis of android RAM images},
  series = {Proceedings of the 2nd international conference on information systems security and privacy},
  booktitle = {Proceedings of the 2nd international conference on information systems security and privacy},
  organization    = {ICISSP International Conference on Information Systems Security and Privacy <2, 2016, Rome, Italy>},
  isbn      = {978-989-758-167-0},
  doi       = {10.5220/0005652802550264},
  pages     = {255 -- 264},
  year      = {2016},
  language  = {en}
}
@inproceedings{SchulzeMuehleisenFeyerl2018,
  author    = {Schulze, Sven and M{\"u}hleisen, M. and Feyerl, G{\"u}nter},
  title     = {Adaptive energy management strategy for a heavy-duty truck with a P2-hybrid topology},
  series = {18. Internationales Stuttgarter Symposium. Proceedings},
  booktitle = {18. Internationales Stuttgarter Symposium. Proceedings},
  publisher = {Springer Vieweg},
  address   = {Wiesbaden},
  doi       = {10.1007/978-3-658-21194-3},
  pages     = {75 -- 89},
  year      = {2018},
  language  = {en}
}
@article{RoethPielenWolffetal.2018,
  author    = {R{\"o}th, Thilo and Pielen, Michael and Wolff, Klaus and L{\"u}diger, Thomas},
  title     = {Urbane Fahrzeugkonzepte f{\"u}r die Shared Mobility},
  series = {Automobiltechnische Zeitschrift - ATZ},
  volume    = {120},
  journal   = {Automobiltechnische Zeitschrift - ATZ},
  number    = {1},
  publisher = {Springer Vieweg},
  address   = {Wiesbaden},
  issn      = {0001-2785},
  doi       = {10.1007/s35148-017-0176-8},
  pages     = {18 -- 23},
  year      = {2018},
  abstract  = {Urbane Mobilit{\"a}tskonzepte der Zukunft erfordern neue Unternehmensformen, idealerweise aus Old Economy und New Economy, sowie eine enge Anbindung an die gesellschaftsrelevante Zukunftsforschung. F{\"u}r neue Fahrzeugkonzepte des Carsharing bedeutet dies, dass alle kostenverursachenden Faktoren erfasst und analysiert werden m{\"u}ssen. Die FH Aachen, share2drive und FEV geben einen Ausblick auf die zuk{\"u}nftige Fahrzeugklasse der Personal Public Vehicles als „Rolling Device".},
  language  = {de}
}
@inproceedings{NowackRoethBuehrigPolaczeketal.2008,
  author    = {Nowack, N. and R{\"o}th, Thilo and B{\"u}hrig-Polaczek, A. and Klaus, G.},
  title     = {Advanced Sheet Metal Components Reinforced by Light Metal Cast Structures},
  series = {Aluminium alloys : their physical and mechanical properties ; [proceedings of the 11th International Conference on Aluminium Alloys, 22 - 26 Sept. 2008, Aachen, Germany ; ICAA 11]},
  booktitle = {Aluminium alloys : their physical and mechanical properties ; [proceedings of the 11th International Conference on Aluminium Alloys, 22 - 26 Sept. 2008, Aachen, Germany ; ICAA 11]},
  number    = {2},
  editor    = {Hirsch, J{\"u}rgen},
  isbn      = {978-3-527-32367-8},
  pages     = {2374 -- 2381},
  year      = {2008},
  language  = {en}
}
@inproceedings{PaslighFunkeRoethetal.2010,
  author    = {Pasligh, N. and Funke, D. and R{\"o}th, Thilo and Krack, R.},
  title     = {Leichtbau Quertrager als Stahlblech-Aluminiumdruckguss-Hybrid - Von der numerischen Berechnung bis zum realen Prototypen},
  series = {VDI BERICHTE},
  booktitle = {VDI BERICHTE},
  publisher = {VDI Verlag},
  address   = {D{\"u}sseldorf},
  isbn      = {978-3-18-092107-5},
  pages     = {688 Seiten},
  year      = {2010},
  language  = {de}
}
@inproceedings{LaoBuehrigPolaczekRoeth2011,
  author    = {Lao, B. and B{\"u}hrig-Polaczek, A. and R{\"o}th, Thilo},
  title     = {Funktionsintegrierte Leichtbaustrukturen in gussintensiver Metall-Hybridbauweise},
  series = {Verbundwerkstoffe und Werkstoffverbunde: Tagungsband zum 18. Symposium ; 30.03.2011 bis 01.04.2011, Chemnitz},
  booktitle = {Verbundwerkstoffe und Werkstoffverbunde: Tagungsband zum 18. Symposium ; 30.03.2011 bis 01.04.2011, Chemnitz},
  editor    = {Wielage, Bernhard},
  publisher = {Eigenverlag},
  address   = {Chemnitz},
  isbn      = {978-3-00-033801-4},
  pages     = {413 -- 421},
  year      = {2011},
  language  = {de}
}
@article{WeiheErnstRoethetal.2013,
  author    = {Weihe, Stefan and Ernst, Ansgar and R{\"o}th, Thilo and Proksch, Johannes},
  title     = {Aluminium-Stahl-Verbundguss im Nutzfahrzeugbau},
  series = {ATZ - Automobiltechnische Zeitschrift},
  volume    = {115},
  journal   = {ATZ - Automobiltechnische Zeitschrift},
  number    = {4},
  publisher = {Springer Fachmedien Wiesbaden},
  issn      = {2192-8800 (Online)},
  pages     = {312 -- 316},
  year      = {2013},
  abstract  = {In modernen Fahrzeugkarosserien der Großserie kommen zunehmend Materialmischbauweisen zur Anwendung. In Zusammenarbeit der Daimler AG, der Tower Automotive Holding GmbH, der Imperia GmbH sowie der Partnerunternehmen KSM Castings GmbH und Schaufler Tooling GmbH \& Co. KG wird das Leichtbaupotenzial von Aluminiumverbundguss-Stahlblech-Hybriden am Beispiel des vorderen Dachquertr{\"a}gers des Mercedes-Benz Viano/Vito ausf{\"u}hrlich untersucht.},
  language  = {de}
}
@article{KreyerMuellerEsch2020,
  author    = {Kreyer, J{\"o}rg and M{\"u}ller, Marvin and Esch, Thomas},
  title     = {A Calculation Methodology for Predicting Exhaust Mass Flows and Exhaust Temperature Profiles for Heavy-Duty Vehicles},
  series = {SAE International Journal of Commercial Vehicles},
  volume    = {13},
  journal   = {SAE International Journal of Commercial Vehicles},
  number    = {2},
  publisher = {SAE International},
  address   = {Warrendale, Pa.},
  issn      = {1946-3928},
  doi       = {10.4271/02-13-02-0009},
  pages     = {129 -- 143},
  year      = {2020},
  abstract  = {The predictive control of commercial vehicle energy management systems, such as vehicle thermal management or waste heat recovery (WHR) systems, are discussed on the basis of information sources from the field of environment recognition and in combination with the determination of the vehicle system condition. In this article, a mathematical method for predicting the exhaust gas mass flow and the exhaust gas temperature is presented based on driving data of a heavy-duty vehicle. The prediction refers to the conditions of the exhaust gas at the inlet of the exhaust gas recirculation (EGR) cooler and at the outlet of the exhaust gas aftertreatment system (EAT). The heavy-duty vehicle was operated on the motorway to investigate the characteristic operational profile. In addition to the use of road gradient profile data, an evaluation of the continuously recorded distance signal, which represents the distance between the test vehicle and the road user ahead, is included in the prediction model. Using a Fourier analysis, the trajectory of the vehicle speed is determined for a defined prediction horizon. To verify the method, a holistic simulation model consisting of several hierarchically structured submodels has been developed. A map-based submodel of a combustion engine is used to determine the EGR and EAT exhaust gas mass flows and exhaust gas temperature profiles. All simulation results are validated on the basis of the recorded vehicle and environmental data. Deviations from the predicted values are analyzed and discussed.},
  language  = {en}
}
@article{SerrorHackHenzeetal.2021,
  author    = {Serror, Martin and Hack, Sacha and Henze, Martin and Schuba, Marko and Wehrle, Klaus},
  title     = {Challenges and Opportunities in Securing the Industrial Internet of Things},
  series = {IEEE Transactions on Industrial Informatics},
  volume    = {17},
  journal   = {IEEE Transactions on Industrial Informatics},
  number    = {5},
  publisher = {IEEE},
  address   = {New York},
  issn      = {1941-0050},
  doi       = {10.1109/TII.2020.3023507},
  pages     = {2985 -- 2996},
  year      = {2021},
  language  = {en}
}
@inproceedings{MerkensHebel2021,
  author    = {Merkens, Torsten and Hebel, Christoph},
  title     = {Sharing mobility concepts - flexible, sustainable, smart},
  series = {Proceedings of the 1st UNITED - Southeast Asia Automotive Interest Group (SAIG) International Conference},
  booktitle = {Proceedings of the 1st UNITED - Southeast Asia Automotive Interest Group (SAIG) International Conference},
  isbn      = {978-3-902103-94-9},
  pages     = {43 -- 44},
  year      = {2021},
  language  = {en}
}
@inproceedings{WuKemper2016,
  author    = {Wu, Ziyi and Kemper, Hans},
  title     = {The optimal 48 V - battery pack for a specific load profile of a heavy duty vehicle},
  series = {8. Internationale Fachtagung Kraftwerk Batterie : 26. - 27. April 2016, M{\"u}nster, Deutschland},
  booktitle = {8. Internationale Fachtagung Kraftwerk Batterie : 26. - 27. April 2016, M{\"u}nster, Deutschland},
  year      = {2016},
  language  = {en}
}
@inproceedings{NeuJanserKhatibietal.2016,
  author    = {Neu, Eugen and Janser, Frank and Khatibi, Akbar A. and Orifici, Adrian C.},
  title     = {In-flight vibration-based structural health monitoring of aircraft wings},
  series = {30th Congress of the internatonal council of the aeronautical sciences : 25.-30. September 2016, Daejeon, Korea},
  booktitle = {30th Congress of the internatonal council of the aeronautical sciences : 25.-30. September 2016, Daejeon, Korea},
  pages     = {10 Seiten},
  year      = {2016},
  abstract  = {This work presents a methodology for automated damage-sensitive feature extraction and anomaly detection under multivariate operational variability for in-flight assessment of wings. The method uses a passive excitation approach, i. e. without the need for artificial actuation. The modal system properties (natural frequencies and damping ratios) are used as damage-sensitive features. Special emphasis is placed on the use of Fiber Bragg Grating (FBG) sensing technology and the consideration of Operational and Environmental Variability (OEV). Measurements from a wind tunnel investigation with a composite cantilever equipped with FBG and piezoelectric sensors are used to successfully detect an impact damage. In addition, the feasibility of damage localisation and severity estimation is evaluated based on the coupling found between damageand OEV-induced feature changes.},
  language  = {en}
}
@article{PetersonRoethUibel2017,
  author    = {Peterson, Leif Arne and R{\"o}th, Thilo and Uibel, Thomas},
  title     = {Einsatz von Holzwerkstoffen in Fahrzeugstrukturen},
  series = {Bauen mit Holz},
  journal   = {Bauen mit Holz},
  number    = {3},
  publisher = {Bruderverlag},
  address   = {K{\"o}ln},
  issn      = {0005-6545},
  pages     = {32 -- 38},
  year      = {2017},
  language  = {de}
}
@inproceedings{PetersonRoethUibel2017,
  author    = {Peterson, Leif Arne and R{\"o}th, Thilo and Uibel, Thomas},
  title     = {Holzwerkstoffe in Karosseriestrukturen},
  series = {Tagungsband Aachener Holzbautagung 2017},
  booktitle = {Tagungsband Aachener Holzbautagung 2017},
  editor    = {Uibel, Thormas and Peterson, Leif Arne and Baumann, Marcus},
  issn      = {2197-4489},
  pages     = {34 -- 45},
  year      = {2017},
  language  = {de}
}
@incollection{RoethDeutskensKreiskoetheretal.2018,
  author    = {R{\"o}th, Thilo and Deutskens, Christoph and Kreisk{\"o}ther, Kai and Heimes, Heiner Hans and Schittny, Bastian and Ivanescu, Sebastian and Kleine B{\"u}ning, Max and Reinders, Christian and Wessels, Saskia and Haunreiter, Andreas and Reisgen, Uwe and Thiele, Regina and Hameyer, Kay and Doncker, Rik W. de and Sauer, Uwe and Hoek, Hauke van and H{\"u}bner, Mareike and Hennen, Martin and Stolze, Thilo and Vetter, Andreas and Hagedorn, J{\"u}rgen and M{\"u}ller, Dirk and Rewitz, Kai and Wesseling, Mark and Flieger, Bj{\"o}rn},
  title     = {Entwicklung von elektrofahrzeugspezifischen Systemen},
  series = {Elektromobilit{\"a}t},
  booktitle = {Elektromobilit{\"a}t},
  publisher = {Springer Vieweg},
  address   = {Berlin, Heidelberg},
  isbn      = {978-3-662-53137-2},
  doi       = {10.1007/978-3-662-53137-2_6},
  pages     = {279 -- 386},
  year      = {2018},
  abstract  = {Die Batterie ist eine der absolut zentralen Komponenten des Elektrofahrzeugs. Die serielle Entwicklung und Produktion dieser Batterien und die Verbesserung der Leistungen wird entscheidend f{\"u}r den Erfolg der Elektromobilit{\"a}t sein. Die Batterie ist jedoch nicht das einzige elektrofahrzeugspezifische System, das neu entwickelt, umkonzipiert oder verbessert werden muss. So sind ebenso die Entwicklung der neuen Fahrzeugstruktur sowie des elektrifizierten Antriebsstranges Teil dieses Kapitels. Weiterhin wird ein Blick auf das bedeutende Thema des Thermomanagements geworfen.},
  language  = {de}
}
@article{WilbringEnningPfaffetal.2020,
  author    = {Wilbring, Daniela and Enning, Manfred and Pfaff, Raphael and Schmidt, Bernd},
  title     = {Neue Perspektiven f{\"u}r die Bahn in der Produktions- und Distributionslogistik durch Prozessautomation},
  series = {ETR - Eisenbahntechnische Rundschau},
  volume    = {69},
  journal   = {ETR - Eisenbahntechnische Rundschau},
  number    = {3},
  issn      = {0013-2845},
  pages     = {15 -- 19},
  year      = {2020},
  language  = {de}
}
@inproceedings{DinghoferHartung2020,
  author    = {Dinghofer, Kai and Hartung, Frank},
  title     = {Analysis of Criteria for the Selection of Machine Learning Frameworks},
  series = {2020 International Conference on Computing, Networking and Communications (ICNC)},
  booktitle = {2020 International Conference on Computing, Networking and Communications (ICNC)},
  publisher = {IEEE},
  address   = {New York, NY},
  doi       = {10.1109/ICNC47757.2020.9049650},
  pages     = {373 -- 377},
  year      = {2020},
  abstract  = {With the many achievements of Machine Learning in the past years, it is likely that the sub-area of Deep Learning will continue to deliver major technological breakthroughs [1]. In order to achieve best results, it is important to know the various different Deep Learning frameworks and their respective properties. This paper provides a comparative overview of some of the most popular frameworks. First, the comparison methods and criteria are introduced and described with a focus on computer vision applications: Features and Uses are examined by evaluating papers and articles, Adoption and Popularity is determined by analyzing a data science study. Then, the frameworks TensorFlow, Keras, PyTorch and Caffe are compared based on the previously described criteria to highlight properties and differences. Advantages and disadvantages are compared, enabling researchers and developers to choose a framework according to their specific needs.},
  language  = {en}
}
@inproceedings{KreyerMuellerEsch2020,
  author    = {Kreyer, J{\"o}rg and M{\"u}ller, Marvin and Esch, Thomas},
  title     = {A Map-Based Model for the Determination of Fuel Consumption for Internal Combustion Engines as a Function of Flight Altitude},
  publisher = {DGLR},
  address   = {Bonn},
  doi       = {10.25967/490162},
  pages     = {13 Seiten},
  year      = {2020},
  abstract  = {In addition to very high safety and reliability requirements, the design of internal combustion engines (ICE) in aviation focuses on economic efficiency. The objective must be to design the aircraft powertrain optimized for a specific flight mission with respect to fuel consumption and specific engine power. Against this background, expert tools provide valuable decision-making assistance for the customer. In this paper, a mathematical calculation model for the fuel consumption of aircraft ICE is presented. This model enables the derivation of fuel consumption maps for different engine configurations. Depending on the flight conditions and based on these maps, the current and the integrated fuel consumption for freely definable flight emissions is calculated. For that purpose, an interpolation method is used, that has been optimized for accuracy and calculation time. The mission boundary conditions flight altitude and power requirement of the ICE form the basis for this calculation. The mathematical fuel consumption model is embedded in a parent program. This parent program presents the simulated fuel consumption by means of an example flight mission for a representative airplane. The focus of the work is therefore on reproducing exact consumption data for flight operations. By use of the empirical approaches according to Gagg-Farrar [1] the power and fuel consumption as a function of the flight altitude are determined. To substantiate this approaches, a 1-D ICE model based on the multi-physical simulation tool GT-Suite® has been created. This 1-D engine model offers the possibility to analyze the filling and gas change processes, the internal combustion as well as heat and friction losses for an ICE under altitude environmental conditions. Performance measurements on a dynamometer at sea level for a naturally aspirated ICE with a displacement of 1211 ccm used in an aviation aircraft has been done to validate the 1-D ICE model. To check the plausibility of the empirical approaches with respect to the fuel consumption and performance adjustment for the flight altitude an analysis of the ICE efficiency chain of the 1-D engine model is done. In addition, a comparison of literature and manufacturer data with the simulation results is presented.},
  language  = {en}
}
@article{KhayyamJamaliBabHadiasharetal.2020,
  author    = {Khayyam, Hamid and Jamali, Ali and Bab-Hadiashar, Alireza and Esch, Thomas and Ramakrishna, Seeram and Jalil, Mahdi and Naebe, Minoo},
  title     = {A Novel Hybrid Machine Learning Algorithm for Limited and Big Data Modelling with Application in Industry 4.0},
  series = {IEEE Access},
  journal   = {IEEE Access},
  publisher = {IEEE},
  address   = {New York, NY},
  isbn      = {2169-3536},
  doi       = {10.1109/ACCESS.2020.2999898},
  pages     = {1 -- 12},
  year      = {2020},
  abstract  = {To meet the challenges of manufacturing smart products, the manufacturing plants have been radically changed to become smart factories underpinned by industry 4.0 technologies. The transformation is assisted by employment of machine learning techniques that can deal with modeling both big or limited data. This manuscript reviews these concepts and present a case study that demonstrates the use of a novel intelligent hybrid algorithms for Industry 4.0 applications with limited data. In particular, an intelligent algorithm is proposed for robust data modeling of nonlinear systems based on input-output data. In our approach, a novel hybrid data-driven combining the Group-Method of Data-Handling and Singular-Value Decomposition is adapted to find an offline deterministic model combined with Pareto multi-objective optimization to overcome the overfitting issue. An Unscented-Kalman-Filter is also incorporated to update the coefficient of the deterministic model and increase its robustness against data uncertainties. The effectiveness of the proposed method is examined on a set of real industrial measurements.},
  language  = {en}
}
@inproceedings{NikolovskiRekeElsenetal.2021,
  author    = {Nikolovski, Gjorgji and Reke, Michael and Elsen, Ingo and Schiffer, Stefan},
  title     = {Machine learning based 3D object detection for navigation in unstructured environments},
  series = {2021 IEEE Intelligent Vehicles Symposium Workshops (IV Workshops)},
  booktitle = {2021 IEEE Intelligent Vehicles Symposium Workshops (IV Workshops)},
  publisher = {IEEE},
  isbn      = {978-1-6654-7921-9},
  doi       = {10.1109/IVWorkshops54471.2021.9669218},
  pages     = {236 -- 242},
  year      = {2021},
  abstract  = {In this paper we investigate the use of deep neural networks for 3D object detection in uncommon, unstructured environments such as in an open-pit mine. While neural nets are frequently used for object detection in regular autonomous driving applications, more unusual driving scenarios aside street traffic pose additional challenges. For one, the collection of appropriate data sets to train the networks is an issue. For another, testing the performance of trained networks often requires tailored integration with the particular domain as well. While there exist different solutions for these problems in regular autonomous driving, there are only very few approaches that work for special domains just as well. We address both the challenges above in this work. First, we discuss two possible ways of acquiring data for training and evaluation. That is, we evaluate a semi-automated annotation of recorded LIDAR data and we examine synthetic data generation. Using these datasets we train and test different deep neural network for the task of object detection. Second, we propose a possible integration of a ROS2 detector module for an autonomous driving platform. Finally, we present the performance of three state-of-the-art deep neural networks in the domain of 3D object detection on a synthetic dataset and a smaller one containing a characteristic object from an open-pit mine.},
  language  = {en}
}
@inproceedings{FiedlerGottschlichMuellerMelcher2021,
  author    = {Fiedler, Gerda and Gottschlich-M{\"u}ller, Birgit and Melcher, Karin},
  title     = {Online-Pr{\"u}fungen mit STACK Aufgaben},
  series = {Tagungsband ASIM Workshop STS/GMMS/EDU 2021},
  booktitle = {Tagungsband ASIM Workshop STS/GMMS/EDU 2021},
  editor    = {Liu-Henke, Xiaobo and Durak, Umut},
  publisher = {ARGESIM Verlag},
  address   = {Wien},
  isbn      = {978-3-901608-69-8},
  doi       = {10.11128/arep.45},
  pages     = {173 -- 178},
  year      = {2021},
  abstract  = {Wir stellen hier exemplarisch STACK Aufgaben vor, die frei von der Problematik sind, welche sich durch diverse Kommunikationswege und (webbasierte) Computer Algebra Systeme (CAS) ergibt. Daher sind sie insbesondere f{\"u}r eine Open-Book Online Pr{\"u}fung geeignet, da eine faire Pr{\"u}fungssituation gew{\"a}hrleistet werden kann.},
  language  = {de}
}
@article{HahnHebelManz2022,
  author    = {Hahn, Geogr W. and Hebel, Christoph and Manz, W.},
  title     = {Die neuen Empfehlungen f{\"u}r Verkehrsnachfragemodellierung im Personenverkehr},
  series = {Straßenverkehrstechnik},
  volume    = {66},
  journal   = {Straßenverkehrstechnik},
  number    = {10},
  publisher = {Kirschbaum Verlag GmbH},
  address   = {Bonn},
  issn      = {0039-2219},
  doi       = {10.53184/SVT10-2022-1},
  pages     = {721 -- 726},
  year      = {2022},
  abstract  = {Die neu erschienenen „Empfehlungen zum Einsatz von Verkehrsnachfragemodellen f{\"u}r den Personenverkehr" liefern erstmals als Empfehlungspapier der Forschungsgesellschaft f{\"u}r Straßen- und Verkehrswesen einen umfassenden {\"U}berblick zu den verschiedenen Aspekten der Modellierung und geben dem Fachplaner konkrete Hilfestellung f{\"u}r die Konzeption von Nachfragemodellen. Das Empfehlungspapier zielt unter anderem darauf ab, die Erwartungen und das Anspruchsniveau in Hinblick auf Sachgerechtigkeit der Modelle, die erzielbare Modellqualit{\"a}t und den Detaillierungsgrad der Modellaussagen zu harmonisieren.},
  language  = {de}
}
@article{EmigHebelSchwark2022,
  author    = {Emig, J. and Hebel, Christoph and Schwark, A.},
  title     = {Einsatzbereiche f{\"u}r Verkehrsnachfragemodelle},
  series = {Straßenverkehrstechnik},
  volume    = {66},
  journal   = {Straßenverkehrstechnik},
  number    = {10},
  publisher = {Kirschbaum Verlag GmbH},
  address   = {Bonn},
  issn      = {0039-2219},
  doi       = {10.53184/SVT10-2022-2},
  pages     = {727 -- 736},
  year      = {2022},
  abstract  = {In der Praxis bestehen vielf{\"a}ltige Einsatzbereiche f{\"u}r Verkehrsnachfragemodelle. Mit ihnen k{\"o}nnen Kenngr{\"o}ßen des Verkehrsangebots und der Verkehrsnachfrage f{\"u}r den heutigen Zustand wie auch f{\"u}r zuk{\"u}nftige Zust{\"a}nde bereitgestellt werden, um so die Grundlagen f{\"u}r verkehrsplanerische Entscheidungen zu liefern. Die neuen „Empfehlungen zum Einsatz von Verkehrsnachfragemodellen f{\"u}r den Personenverkehr" (EVNM-PV) (FGSV 2022) veranschaulichen anhand von typischen Planungsaufgaben, welche differenzierten Anforderungen daraus f{\"u}r die Modellkonzeption und -erstellung resultieren. Vor dem Hintergrund der konkreten Aufgabenstellung sowie deren spezifischer planerischer Anforderungen bildet die abzuleitende Modellspezifikation die verabredete Grundlage zwischen Auftraggeber und Modellersteller f{\"u}r die konkrete inhaltliche, fachliche Ausgestaltung des Verkehrsmodells.},
  language  = {de}
}
@article{PfaffGidaszewskiSchmidt2020,
  author    = {Pfaff, Raphael and Gidaszewski, Lars and Schmidt, Bernd},
  title     = {Ber{\"u}cksichtigung von No Fault Found im Diagnose- und Instandhaltungssystem von Schienenfahrzeugen},
  series = {ETR - Eisenbahntechnische Rundschau},
  journal   = {ETR - Eisenbahntechnische Rundschau},
  number    = {5},
  publisher = {DVV Media Group},
  address   = {Hamburg},
  issn      = {0013-2845},
  pages     = {56 -- 59},
  year      = {2020},
  abstract  = {Intermittierende und nicht reproduzierbare Fehler, auch als No Fault Found bezeichnet, treten in praktisch allen Bereichen auf und sorgen f{\"u}r hohe Kosten. Diese sind h{\"a}ufig auf unpr{\"a}zise Fehlerbeschreibungen zur{\"u}ckzuf{\"u}hren. Im vorliegenden Beitrag werden Anpassungen der Vorgehensweise bei der Entwicklung und Anpassungen des Diagnosesystems vorgeschlagen.},
  language  = {de}
}
@article{HoevelerBauknechtWolfetal.2020,
  author    = {Hoeveler, B. and Bauknecht, Andr{\´e} and Wolf, C. Christian and Janser, Frank},
  title     = {Wind-Tunnel Study of a Wing-Embedded Lifting Fan Remaining Open in Cruise Flight},
  series = {Journal of Aircraft},
  volume    = {57},
  journal   = {Journal of Aircraft},
  number    = {4},
  publisher = {AIAA},
  address   = {Reston, Va.},
  issn      = {1533-3868},
  doi       = {10.2514/1.C035422},
  year      = {2020},
  abstract  = {It is investigated whether a nonrotating lifting fan remaining uncovered during cruise flight, as opposed to being covered by a shutter system, can be realized with limited additional drag and loss of lift during cruise flight. A wind-tunnel study of a wing-embedded lifting fan has been conducted at the Side Wind Test Facility G{\"o}ttingen of DLR, German Aerospace Center in G{\"o}ttingen using force, pressure, and stereoscopic particle image velocimetry techniques. The study showed that a step on the lower side of the wing in front of the lifting fan duct increases the lift-to-drag ratio of the whole model by up to 25\% for all positive angles of attack. Different sizes and inclinations of the step had limited influence on the surface pressure distribution. The data indicate that these parameters can be optimized to maximize the lift-to-drag ratio. A doubling of the curvature radius of the lifting fan duct inlet lip on the upper side of the wing affected the lift-to-drag ratio by less than 1\%. The lifting fan duct inlet curvature can therefore be optimized to maximize the vertical fan thrust of the rotating lifting fan during hovering without affecting the cruise flight performance with a nonrotating fan.},
  language  = {en}
}
@article{KhayyamJamaliBabHadiasharetal.2020,
  author    = {Khayyam, Hamid and Jamali, Ali and Bab-Hadiashar, Alireza and Esch, Thomas and Ramakrishna, Seeram and Jalili, Mahdi and Naebe, Minoo},
  title     = {A Novel Hybrid Machine Learning Algorithm for Limited and Big Data Modeling with Application in Industry 4.0},
  series = {IEEE Access},
  volume    = {8},
  journal   = {IEEE Access},
  number    = {Art. 9108222},
  publisher = {IEEE},
  address   = {New York, NY},
  issn      = {2169-3536},
  doi       = {10.1109/ACCESS.2020.2999898},
  pages     = {111381 -- 111393},
  year      = {2020},
  abstract  = {To meet the challenges of manufacturing smart products, the manufacturing plants have been radically changed to become smart factories underpinned by industry 4.0 technologies. The transformation is assisted by employment of machine learning techniques that can deal with modeling both big or limited data. This manuscript reviews these concepts and present a case study that demonstrates the use of a novel intelligent hybrid algorithms for Industry 4.0 applications with limited data. In particular, an intelligent algorithm is proposed for robust data modeling of nonlinear systems based on input-output data. In our approach, a novel hybrid data-driven combining the Group-Method of Data-Handling and Singular-Value Decomposition is adapted to find an offline deterministic model combined with Pareto multi-objective optimization to overcome the overfitting issue. An Unscented-Kalman-Filter is also incorporated to update the coefficient of the deterministic model and increase its robustness against data uncertainties. The effectiveness of the proposed method is examined on a set of real industrial measurements.},
  language  = {en}
}
@article{PfaffEnningSutter2022,
  author    = {Pfaff, Raphael and Enning, Manfred and Sutter, Stefan},
  title     = {A risk‑based approach to automatic brake tests for rail freight service: incident analysis and realisation concept},
  series = {SN Applied Sciences},
  volume    = {4},
  journal   = {SN Applied Sciences},
  number    = {4},
  publisher = {Springer},
  address   = {Cham},
  issn      = {2523-3971},
  doi       = {10.1007/s42452-022-05007-x},
  pages     = {1 -- 14},
  year      = {2022},
  abstract  = {This study reviews the practice of brake tests in freight railways, which is time consuming and not suitable to detect certain failure types. Public incident reports are analysed to derive a reasonable brake test hardware and communication architecture, which aims to provide automatic brake tests at lower cost than current solutions. The proposed solutions relies exclusively on brake pipe and brake cylinder pressure sensors, a brake release position switch as well as radio communication via standard protocols. The approach is embedded in the Wagon 4.0 concept, which is a holistic approach to a smart freight wagon. The reduction of manual processes yields a strong incentive due to high savings in manual labour and increased productivity.},
  language  = {en}
}
@article{NeuJanserKhatibietal.2017,
  author    = {Neu, Eugen and Janser, Frank and Khatibi, Akbar A. and Orifici, Adrian C.},
  title     = {Fully Automated Operational Modal Analysis using multi-stage clustering},
  series = {Mechanical Systems and Signal Processing},
  volume    = {Vol. 84, Part A},
  journal   = {Mechanical Systems and Signal Processing},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {0888-3270},
  doi       = {10.1016/j.ymssp.2016.07.031},
  pages     = {308 -- 323},
  year      = {2017},
  language  = {en}
}
@article{NeuJanserKhatibietal.2016,
  author    = {Neu, Eugen and Janser, Frank and Khatibi, Akbar A. and Orifici, Adrian C.},
  title     = {Automated modal parameter-based anomaly detection under varying wind excitation},
  series = {Structural Health Monitoring},
  volume    = {15},
  journal   = {Structural Health Monitoring},
  number    = {6},
  publisher = {Sage},
  address   = {London},
  issn      = {1475-9217},
  doi       = {10.1177/1475921716665803},
  pages     = {1 -- 20},
  year      = {2016},
  abstract  = {Wind-induced operational variability is one of the major challenges for structural health monitoring of slender engineering structures like aircraft wings or wind turbine blades. Damage sensitive features often show an even bigger sensitivity to operational variability. In this study a composite cantilever was subjected to multiple mass configurations, velocities and angles of attack in a controlled wind tunnel environment. A small-scale impact damage was introduced to the specimen and the structural response measurements were repeated. The proposed damage detection methodology is based on automated operational modal analysis. A novel baseline preparation procedure is described that reduces the amount of user interaction to the provision of a single consistency threshold. The procedure starts with an indeterminate number of operational modal analysis identifications from a large number of datasets and returns a complete baseline matrix of natural frequencies and damping ratios that is suitable for subsequent anomaly detection. Mahalanobis distance-based anomaly detection is then applied to successfully detect the damage under varying severities of operational variability and with various degrees of knowledge about the present operational conditions. The damage detection capabilities of the proposed methodology were found to be excellent under varying velocities and angles of attack. Damage detection was less successful under joint mass and wind variability but could be significantly improved through the provision of the currently encountered operational conditions.},
  language  = {en}
}
@incollection{SchubaHoefken2022,
  author    = {Schuba, Marko and H{\"o}fken, Hans-Wilhelm},
  title     = {Cybersicherheit in Produktion, Automotive und intelligenten Geb{\"a}uden},
  series = {IT-Sicherheit - Technologien und Best Practices f{\"u}r die Umsetzung im Unternehmen},
  booktitle = {IT-Sicherheit - Technologien und Best Practices f{\"u}r die Umsetzung im Unternehmen},
  publisher = {Carl Hanser Verlag},
  address   = {M{\"u}nchen},
  isbn      = {978-3-446-47223-5},
  doi       = {10.3139/9783446473478.012},
  pages     = {193 -- 218},
  year      = {2022},
  language  = {de}
}
@incollection{EnglaenderKaminskiSchuba2022,
  author    = {Engl{\"a}nder, Jacques and Kaminski, Lars and Schuba, Marko},
  title     = {Informationssicherheitsmanagement},
  series = {Digitalisierungs- und Informationsmanagement},
  booktitle = {Digitalisierungs- und Informationsmanagement},
  publisher = {Springer Vieweg},
  address   = {Berlin},
  isbn      = {978-3-662-63757-9},
  doi       = {10.1007/978-3-662-63758-6_15},
  pages     = {373 -- 398},
  year      = {2022},
  abstract  = {Daten und Informationen sind die wichtigsten Ressourcen vieler Unternehmen und m{\"u}ssen daher entsprechend gesch{\"u}tzt werden. Getrieben durch die erh{\"o}hte Vernetzung von Informationstechnologie, die h{\"o}here Offenheit infolge datengetriebener Dienstleistungen und eine starke Zunahme an Datenquellen, r{\"u}cken die Gefahren von Informationsdiebstahl, -manipulation und -verlust in den Fokus von produzierenden Unternehmen. Auf dem Weg zum lern- und wandlungsf{\"a}higen Unternehmen kann dies zu einem großen Hindernis werden, da einerseits zu hohe Sicherheitsanforderungen neue Entwicklungen beschr{\"a}nken, andererseits wegen des Mangels an ausreichenden Informationssicherheitskonzepten Unternehmen weniger Innovationen wagen. Deshalb bedarf es individuell angepasster Konzepte f{\"u}r die Bereiche IT-Security, IT-Safety und Datenschutz f{\"u}r vernetzte Produkte, Produktion und Arbeitspl{\"a}tze. Bei der Entwicklung und Durchsetzung dieser Konzepte steht der Faktor Mensch im Zentrum aller {\"U}berlegungen. In diesem Kapitel wird dargestellt, wie der Faktor Mensch bei der Erstellung von Informationssicherheitskonzepten in verschiedenen Phasen zu beachten ist. Beginnend mit der Integration von Informationssystemen und damit verbundenen Sicherheitsmaßnahmen, {\"u}ber die Administration, bis hin zur Anwendung durch den Endnutzer, werden Methoden beschrieben, die den Menschen, verbunden mit seinem Mehrwert wie auch den Risiken, einschließen. Dabei werden sowohl Grundlagen aufgezeigt als auch Konzepte vorgestellt, mit denen Entscheider in der Unternehmens-IT Leitlinien f{\"u}r die Informationssicherheit festlegen k{\"o}nnen.},
  language  = {de}
}
@inproceedings{SchubaHoefkenLinzbach2022,
  author    = {Schuba, Marko and H{\"o}fken, Hans-Wilhelm and Linzbach, Sophie},
  title     = {An ICS Honeynet for Detecting and Analyzing Cyberattacks in Industrial Plants},
  series = {2021 International Conference on Electrical, Computer and Energy Technologies (ICECET)},
  booktitle = {2021 International Conference on Electrical, Computer and Energy Technologies (ICECET)},
  publisher = {IEEE},
  isbn      = {978-1-6654-4231-2},
  doi       = {10.1109/ICECET52533.2021.9698746},
  pages     = {6 Seiten},
  year      = {2022},
  abstract  = {Cybersecurity of Industrial Control Systems (ICS) is an important issue, as ICS incidents may have a direct impact on safety of people or the environment. At the same time the awareness and knowledge about cybersecurity, particularly in the context of ICS, is alarmingly low. Industrial honeypots offer a cheap and easy to implement way to raise cybersecurity awareness and to educate ICS staff about typical attack patterns. When integrated in a productive network, industrial honeypots may not only reveal attackers early but may also distract them from the actual important systems of the network. Implementing multiple honeypots as a honeynet, the systems can be used to emulate or simulate a whole Industrial Control System. This paper describes a network of honeypots emulating HTTP, SNMP, S7communication and the Modbus protocol using Conpot, IMUNES and SNAP7. The nodes mimic SIMATIC S7 programmable logic controllers (PLCs) which are widely used across the globe. The deployed honeypots' features will be compared with the features of real SIMATIC S7 PLCs. Furthermore, the honeynet has been made publicly available for ten days and occurring cyberattacks have been analyzed},
  language  = {en}
}
@inproceedings{ChristianMontagSchubaetal.2018,
  author    = {Christian, Esser and Montag, Tim and Schuba, Marko and Allhof, Manuel},
  title     = {Future critical infrastructure and security - cyberattacks on charging stations},
  series = {31st International Electric Vehicle Symposium \& Exhibition and International Electric Vehicle Technology Conference (EVS31 \& EVTeC 2018)},
  booktitle = {31st International Electric Vehicle Symposium \& Exhibition and International Electric Vehicle Technology Conference (EVS31 \& EVTeC 2018)},
  publisher = {Society of Automotive Engineers of Japan (JSAE)},
  address   = {Tokyo},
  isbn      = {978-1-5108-9157-9},
  pages     = {665 -- 671},
  year      = {2018},
  language  = {en}
}
@article{Pfaff2023,
  author    = {Pfaff, Raphael},
  title     = {Braking distance prediction for vehicle consist in low-speed on-sight operation: a Monte Carlo approach},
  series = {Railway Engineering Science},
  volume    = {31},
  journal   = {Railway Engineering Science},
  number    = {2},
  publisher = {SpringerOpen},
  issn      = {2662-4753 (eISSN)},
  doi       = {10.1007/s40534-023-00303-7},
  pages     = {135 -- 144},
  year      = {2023},
  abstract  = {The first and last mile of a railway journey, in both freight and transit applications, constitutes a high effort and is either non-productive (e.g. in the case of depot operations) or highly inefficient (e.g. in industrial railways). These parts are typically managed on-sight, i.e. with no signalling and train protection systems ensuring the freedom of movement. This is possible due to the rather short braking distances of individual vehicles and shunting consists. The present article analyses the braking behaviour of such shunting units. For this purpose, a dedicated model is developed. It is calibrated on published results of brake tests and validated against a high-definition model for low-speed applications. Based on this model, multiple simulations are executed to obtain a Monte Carlo simulation of the resulting braking distances. Based on the distribution properties and established safety levels, the risk of exceeding certain braking distances is evaluated and maximum braking distances are derived. Together with certain parameters of the system, these can serve in the design and safety assessment of driver assistance systems and automation of these processes.},
  language  = {en}
}
@incollection{HeimesKampkerKehreretal.2023,
  author    = {Heimes, Heiner Hans and Kampker, Achim and Kehrer, Mario and D{\"u}nnwald, Simon and Heetfeld, Lennart and Polzenberg, Jens and Budde, Lucas and Keusen, Maximilian and Pandey, Rahul and R{\"o}th, Thilo},
  title     = {Fahrzeugstruktur},
  series = {Elektromobilit{\"a}t: Grundlagen einer Fortschrittstechnologie},
  booktitle = {Elektromobilit{\"a}t: Grundlagen einer Fortschrittstechnologie},
  editor    = {Kampker, Achim and Heimes, Heiner Hans},
  publisher = {Springer Vieweg},
  address   = {Berlin},
  isbn      = {978-3-662-65811-6 (Print)},
  doi       = {10.1007/978-3-662-65812-3_5},
  pages     = {69 -- 106},
  year      = {2023},
  abstract  = {Um sowohl Treibhausgas-Emissionen zu verringern als auch Kraftstoffressourcen zu schonen, wird zunehmend an einer Transformation konventionell angetriebener Kraftfahrzeuge hin zu elektrifizierten Antriebskonzepten gearbeitet. Basierend auf herk{\"o}mmlichen Fahrzeugen mit Verbrennungsmotor wurde eine Vielzahl neuer Antriebssysteme mit verschiedenem Elektrifizierungsgrad entwickelt. Mitte der 1990er-Jahre kamen erste Fahrzeuge mit einem Hybridantrieb auf den Markt. Die Kombination aus Verbrennungs- und Elektromotor erlaubt eine Verbrauchsreduktion und Bremsenergier{\"u}ckgewinnung sowie lokal emissionsfreies Fahren.},
  language  = {de}
}
@incollection{HeimesKampkerDornetal.2023,
  author    = {Heimes, Heiner Hans and Kampker, Achim and Dorn, Benjamin and Kehrer, Mario and D{\"u}nnwald, Simon and Badura, Dennis and Terren, Maximilian and R{\"o}th, Thilo},
  title     = {Produktionsprozesse der Fahrzeugstruktur},
  series = {Elektromobilit{\"a}t: Grundlagen einer Fortschrittstechnologie},
  booktitle = {Elektromobilit{\"a}t: Grundlagen einer Fortschrittstechnologie},
  editor    = {Kampker, Achim and Heimes, Heiner Hans},
  publisher = {Springer Vieweg},
  address   = {Berlin},
  isbn      = {978-3-662-65811-6 (Print)},
  doi       = {10.1007/978-3-662-65812-3_13},
  pages     = {227 -- 247},
  year      = {2023},
  language  = {de}
}
@book{JanserHavermannHoeveleretal.2023,
  author    = {Janser, Frank and Havermann, Marc and Hoeveler, Bastian and Hertz, Cyril and Bergmann, Ole},
  title     = {Str{\"o}mungslehre und Aerodynamik : inkompressible Profile und Tragfl{\"u}gelaerodynamik, Band 2},
  edition   = {4. Auflage},
  publisher = {Mainz},
  address   = {Aachen},
  isbn      = {978-3-8107-0261-6},
  pages     = {XIII, 211 Seiten},
  year      = {2023},
  abstract  = {Das vorliegende Buch dient als Grundlage f{\"u}r die Bachelor- und Master-Ausbildung von Studierenden im Fachgebiet Str{\"o}mungslehre und Aerodynamik. Im hier behandelten Teilbereich der inkompressiblen Profile und Tragfl{\"u}gelaerodynamik werden schwerpunktm{\"a}ßig die folgenden Themen besprochen: - Profilaerodynamik - Tragfl{\"u}gelaerodynamik - Flugzeugpolare - Methoden zur Flugbereichserweiterung - Schwebeschub und Schwebeleistung - Propellerblattaerodynamik - Numerische Methoden zur Tragfl{\"u}gelberechnung},
  language  = {de}
}
@inproceedings{GaldiHartungDugelay2017,
  author    = {Galdi, Chiara and Hartung, Frank and Dugelay, Jean-Luc},
  title     = {Videos versus still images: Asymmetric sensor pattern noise comparison on mobile phones},
  series = {Electronic Imaging},
  booktitle = {Electronic Imaging},
  publisher = {Society for Imaging Science and Technology},
  address   = {Springfield, Virginia},
  issn      = {2470-1173},
  doi       = {10.2352/ISSN.2470-1173.2017.7.MWSF-331},
  pages     = {100 -- 103},
  year      = {2017},
  abstract  = {Nowadays, the most employed devices for recoding videos or capturing images are undoubtedly the smartphones. Our work investigates the application of source camera identification on mobile phones. We present a dataset entirely collected by mobile phones. The dataset contains both still images and videos collected by 67 different smartphones. Part of the images consists in photos of uniform backgrounds, especially collected for the computation of the RSPN. Identifying the source camera given a video is particularly challenging due to the strong video compression. The experiments reported in this paper, show the large variation in performance when testing an highly accurate technique on still images and videos.},
  language  = {en}
}
@article{SchulzeFeyerlPischinger2023,
  author    = {Schulze, Sven and Feyerl, G{\"u}nter and Pischinger, Stefan},
  title     = {Advanced ECMS for hybrid electric heavy-duty trucks with predictive battery discharge and adaptive operating strategy under real driving conditions},
  series = {Energies},
  volume    = {16},
  journal   = {Energies},
  number    = {13},
  publisher = {MDPI},
  address   = {Basel},
  issn      = {1996-1073},
  doi       = {10.3390/en16135171},
  pages     = {29 Seiten, Art. Nr.: 5171},
  year      = {2023},
  abstract  = {To fulfil the CO2 emission reduction targets of the European Union (EU), heavy-duty (HD) trucks need to operate 15\% more efficiently by 2025 and 30\% by 2030. Their electrification is necessary as conventional HD trucks are already optimized for the long-haul application. The resulting hybrid electric vehicle (HEV) truck gains most of the fuel saving potential by the recuperation of potential energy and its consecutive utilization. The key to utilizing the full potential of HEV-HD trucks is to maximize the amount of recuperated energy and ensure its intelligent usage while keeping the operating point of the internal combustion engine as efficient as possible. To achieve this goal, an intelligent energy management strategy (EMS) based on ECMS is developed for a parallel HEV-HD truck which uses predictive discharge of the battery and adaptive operating strategy regarding the height profile and the vehicle mass. The presented EMS can reproduce the global optimal operating strategy over long phases and lead to a fuel saving potential of up to 2\% compared with a heuristic strategy. Furthermore, the fuel saving potential is correlated with the investigated boundary conditions to deepen the understanding of the impact of intelligent EMS for HEV-HD trucks.},
  language  = {en}
}
@inproceedings{HauggKreyerKemperetal.2020,
  author    = {Haugg, Albert Thomas and Kreyer, J{\"o}rg and Kemper, Hans and Hatesuer, Katerina and Esch, Thomas},
  title     = {Heat exchanger for ORC. adaptability and optimisation potentials},
  series = {IIR International Rankine 2020 Conference},
  booktitle = {IIR International Rankine 2020 Conference},
  doi       = {10.18462/iir.rankine.2020.1224},
  pages     = {10 Seiten},
  year      = {2020},
  abstract  = {The recovery of waste heat requires heat exchangers to extract it from a liquid or gaseous medium into another working medium, a refrigerant. In Organic Rankine Cycles (ORC) on Combustion Engines there are two major heat sources, the exhaust gas and the water/glycol fluid from the engine's cooling circuit. A heat exchanger design must be adapted to the different requirements and conditions resulting from the heat sources, fluids, system configurations, geometric restrictions, and etcetera. The Stacked Shell Cooler (SSC) is a new and very specific design of a plate heat exchanger, created by AKG, which allows with a maximum degree of freedom the optimization of heat exchange rate and the reduction of the related pressure drop. This optimization in heat exchanger design for ORC systems is even more important, because it reduces the energy consumption of the system and therefore maximizes the increase in overall efficiency of the engine.},
  language  = {en}
}
@article{GoettenHavermannBraunetal.2020,
  author    = {G{\"o}tten, Falk and Havermann, Marc and Braun, Carsten and Marino, Matthew and Bil, Cees},
  title     = {Improved Form Factor for Drag Estimation of Fuselages with Various Cross Sections},
  series = {Journal of Aircraft},
  journal   = {Journal of Aircraft},
  publisher = {AIAA},
  address   = {Reston, Va.},
  issn      = {1533-3868},
  doi       = {10.2514/1.C036032},
  pages     = {1 -- 13},
  year      = {2020},
  abstract  = {The paper presents an aerodynamic investigation of 70 different streamlined bodies with fineness ratios ranging from 2 to 10. The bodies are chosen to idealize both unmanned and small manned aircraft fuselages and feature cross-sectional shapes that vary from circular to quadratic. The study focuses on friction and pressure drag in dependency of the individual body's fineness ratio and cross section. The drag forces are normalized with the respective body's wetted area to comply with an empirical drag estimation procedure. Although the friction drag coefficient then stays rather constant for all bodies, their pressure drag coefficients decrease with an increase in fineness ratio. Referring the pressure drag coefficient to the bodies' cross-sectional areas shows a distinct pressure drag minimum at a fineness ratio of about three. The pressure drag of bodies with a quadratic cross section is generally higher than for bodies of revolution. The results are used to derive an improved form factor that can be employed in a classic empirical drag estimation method. The improved formulation takes both the fineness ratio and cross-sectional shape into account. It shows superior accuracy in estimating streamlined body drag when compared with experimental data and other form factor formulations of the literature.},
  language  = {en}
}