@article{BayerTemizArtmannDigeletal.2020,
  author    = {Bayer, Robin and Temiz Artmann, Ayseg{\"u}l and Digel, Ilya and Falkenstein, Julia and Artmann, Gerhard and Creutz, Till and Hescheler, J{\"u}rgen},
  title     = {Mechano-pharmacological testing of L-Type Ca²⁺ channel modulators via human vascular celldrum model},
  series = {Cellular Physiology and Biochemistry},
  volume    = {54},
  journal   = {Cellular Physiology and Biochemistry},
  publisher = {Cell Physiol Biochem Press},
  address   = {D{\"u}sseldorf},
  issn      = {1421-9778},
  doi       = {10.33594/000000225},
  pages     = {371 -- 383},
  year      = {2020},
  abstract  = {Background/Aims: This study aimed to establish a precise and well-defined working model, assessing pharmaceutical effects on vascular smooth muscle cell monolayer in-vitro. It describes various analysis techniques to determine the most suitable to measure the biomechanical impact of vasoactive agents by using CellDrum technology. Methods: The so-called CellDrum technology was applied to analyse the biomechanical properties of confluent human aorta muscle cells (haSMC) in monolayer. The cell generated tensions deviations in the range of a few N/m² are evaluated by the CellDrum technology. This study focuses on the dilative and contractive effects of L-type Ca²⁺ channel agonists and antagonists, respectively. We analyzed the effects of Bay K8644, nifedipine and verapamil. Three different measurement modes were developed and applied to determine the most appropriate analysis technique for the study purpose. These three operation modes are called, particular time mode" (PTM), "long term mode" (LTM) and "real-time mode" (RTM). Results: It was possible to quantify the biomechanical response of haSMCs to the addition of vasoactive agents using CellDrum technology. Due to the supplementation of 100nM Bay K8644, the tension increased approximately 10.6\% from initial tension maximum, whereas, the treatment with nifedipine and verapamil caused a significant decrease in cellular tension: 10nM nifedipine decreased the biomechanical stress around 6,5\% and 50nM verapamil by 2,8\%, compared to the initial tension maximum. Additionally, all tested measurement modes provide similar results while focusing on different analysis parameters. Conclusion: The CellDrum technology allows highly sensitive biomechanical stress measurements of cultured haSMC monolayers. The mechanical stress responses evoked by the application of vasoactive calcium channel modulators were quantified functionally (N/m²). All tested operation modes resulted in equal findings, whereas each mode features operation-related data analysis.},
  language  = {en}
}
@incollection{AltayTaddeiButenwegetal.2014,
  author    = {Altay, Okyay and Taddei, Francesca and Butenweg, Christoph and Klinkel, Sven},
  title     = {Vibration mitigation of wind turbine towers with tuned mass dampers},
  series = {Wind turbine control and monitoring. (Advances in industrial control)},
  booktitle = {Wind turbine control and monitoring. (Advances in industrial control)},
  publisher = {Springer},
  address   = {Cham ; Heidelberg ; New York ; Dordrecht ; London},
  isbn      = {978-3-319-08412-1 (Print) ; 978-3-319-08413-8 (E-Book)},
  doi       = {10.1007/978-3-319-08413-8_12},
  pages     = {337 -- 373},
  year      = {2014},
  abstract  = {Because of its minor environmental impact, electricity generation using wind power is getting remarkable. The further growth of the wind industry depends on technological solutions to the challenges in production and construction of the turbines. Wind turbine tower vibrations, which limit power generation efficiency and cause fatigue problems with high maintenance costs, count as one of the main structural difficulties in the wind energy sector. To mitigate tower vibrations auxiliary measures are necessary. The effectiveness of tuned mass damper is verified by means of a numeric study on a 5 MW onshore reference wind turbine. Hereby, also seismic-induced vibrations and soil-structure interaction are considered. Acquired results show that tuned mass damper can effectively reduce resonant tower vibrations and improve the fatigue life of wind turbines. This chapter is also concerned with tuned liquid column damper and a semiactive application of it. Due to its geometric versatility and low prime costs, tuned liquid column dampers are a good alternative to other damping measures, in particular for slender structures like wind turbines.},
  language  = {en}
}
@inproceedings{KalkerNeumannButenwegetal.2005,
  author    = {Kalker, Ines and Neumann, M. and Butenweg, Christoph and Holler, Stefan},
  title     = {Modelling of textile strengthened masonry},
  series = {Proceedings of the Tenth International Conference on Civil, Structural and Environmental Engineering Computing : [Rome, Italy, 30. August - 2. September 2005] / ed. by B. H. V. Topping},
  booktitle = {Proceedings of the Tenth International Conference on Civil, Structural and Environmental Engineering Computing : [Rome, Italy, 30. August - 2. September 2005] / ed. by B. H. V. Topping},
  publisher = {Civil-Comp Press},
  address   = {Stirling},
  organization    = {International Conference on Civil, Structural and Environmental Engineering Computing <10, 2005, Rome>},
  isbn      = {1-905088-00-0},
  doi       = {10.4203/ccp.81.184},
  pages     = {447 -- 448},
  year      = {2005},
  language  = {en}
}
@inproceedings{KarimiButenwegToll2005,
  author    = {Karimi, Iman and Butenweg, Christoph and Toll, Britta},
  title     = {Vulnerability assessment of industrial facilities},
  series = {Proceedings of the Tenth International Conference on Civil, Structural and Environmental Engineering Computing : [Rome, Italy, 30. August - 2. September 2005] / ed. by B. H. V. Topping},
  booktitle = {Proceedings of the Tenth International Conference on Civil, Structural and Environmental Engineering Computing : [Rome, Italy, 30. August - 2. September 2005] / ed. by B. H. V. Topping},
  publisher = {Civil-Comp Press},
  address   = {Stirling},
  organization    = {International Conference on Civil, Structural and Environmental Engineering Computing <10, 2005, Rome>},
  isbn      = {1-905088-00-0},
  doi       = {10.4203/ccp.81.34},
  pages     = {34, 73 -- 75},
  year      = {2005},
  language  = {en}
}
@inproceedings{MistlerButenweg2005,
  author    = {Mistler, Michael and Butenweg, Christoph},
  title     = {A seismic design procedure for masonry buildings},
  series = {Proceedings of the Tenth International Conference on Civil, Structural and Environmental Engineering Computing : [Rome, Italy, 30. August - 2. September 2005] / ed. by B. H. V. Topping},
  booktitle = {Proceedings of the Tenth International Conference on Civil, Structural and Environmental Engineering Computing : [Rome, Italy, 30. August - 2. September 2005] / ed. by B. H. V. Topping},
  publisher = {Civil-Comp Press},
  address   = {Stirling},
  organization    = {International Conference on Civil, Structural and Environmental Engineering Computing <10, 2005, Rome>},
  isbn      = {1-905088-00-0},
  doi       = {10.4203/ccp.81.193},
  pages     = {465 -- 467},
  year      = {2005},
  language  = {en}
}
@inproceedings{RenaultButenwegMistler2005,
  author    = {Renault, Philippe and Butenweg, Christoph and Mistler, Michael},
  title     = {Seismic vulnerability assessment system for bridges},
  series = {Proceedings of the Tenth International Conference on Civil, Structural and Environmental Engineering Computing : [Rome, Italy, 30. August - 2. September 2005] / ed. by B. H. V. Topping},
  booktitle = {Proceedings of the Tenth International Conference on Civil, Structural and Environmental Engineering Computing : [Rome, Italy, 30. August - 2. September 2005] / ed. by B. H. V. Topping},
  publisher = {Civil-Comp Press},
  address   = {Stirling},
  organization    = {International Conference on Civil, Structural and Environmental Engineering Computing <10, 2005, Rome>},
  isbn      = {1-905088-00-0},
  pages     = {1 -- 14},
  year      = {2005},
  language  = {en}
}
@incollection{Eggert2019,
  author    = {Eggert, Mathias},
  title     = {Big Data Research - How to Structure the Changes of the Past Decade?},
  series = {The Art of Structuring},
  booktitle = {The Art of Structuring},
  publisher = {Springer},
  address   = {Cham},
  isbn      = {978-3-030-06234-7},
  doi       = {10.1007/978-3-030-06234-7_26},
  pages     = {271 -- 281},
  year      = {2019},
  abstract  = {In the past decade, many IS researchers focused on researching the phenomenon of Big Data. At the same time, the relevance of data protection gets more attention than ever before. In particular, since the enactment of the European General Data Protection Regulation in May 2018 Information Systems research should provide answers for protecting personal data. The article at hand presents a structuring framework for Big Data research outcome and the consideration of data protection. IS Researchers might use the framework in order to structure Big Data literature and to identify research gaps that should be addressed in the future.},
  language  = {en}
}
@inproceedings{ChudobaButenwegPfeiffer2003,
  author    = {Chudoba, Rostislav and Butenweg, Christoph and Pfeiffer, Frank},
  title     = {Textile reinforced concrete. Part I: Process model for collaborative research and development},
  series = {Digital proceedings / IKM 2003, proceedings 16th International Conference on the Applications of Computer Science and Mathematics in Architecture and Civil Engineering [Elektronische Ressource : 10. - 12. Juni 2003, Weimar] / Bauhaus-Universit{\"a}t Weimar. Ed.: K. G{\"u}rlebeck; L. Hempel; C. K{\"o}nke},
  booktitle = {Digital proceedings / IKM 2003, proceedings 16th International Conference on the Applications of Computer Science and Mathematics in Architecture and Civil Engineering [Elektronische Ressource : 10. - 12. Juni 2003, Weimar] / Bauhaus-Universit{\"a}t Weimar. Ed.: K. G{\"u}rlebeck; L. Hempel; C. K{\"o}nke},
  publisher = {IKM},
  address   = {Weimar},
  organization    = {Internationales Kolloquium {\"u}ber Anwendungen der Informatik und Mathematik in Architektur und Bauwesen <16, 2003, Weimar>},
  pages     = {1 -- 8},
  year      = {2003},
  language  = {en}
}
@inproceedings{ElDeibChudobaButenwegetal.2002,
  author    = {El-Deib, Khaled and Chudoba, Rostislav and Butenweg, Christoph and Meskouris, Konstantin and K{\"o}nke, Carsten and Bettzieche, Volker},
  title     = {Safety assessment of rockfill and masonry dams},
  series = {Structural dynamics - EURODYN 2002 : proceedings of the 4th [i.e. 5th] International Conference on Structural Dynamics, Munich, Germany, 2 - 5 September 2002 / ed. by H. Grundmann ... Vol. 1},
  booktitle = {Structural dynamics - EURODYN 2002 : proceedings of the 4th [i.e. 5th] International Conference on Structural Dynamics, Munich, Germany, 2 - 5 September 2002 / ed. by H. Grundmann ... Vol. 1},
  publisher = {Balkema},
  address   = {Lisse},
  organization    = {International Conference on Structural Dynamics <5, 2002, M{\"u}nchen>},
  isbn      = {90-5809-510-X},
  pages     = {237 -- 242},
  year      = {2002},
  language  = {en}
}
@inproceedings{HollerButenwegNohetal.2002,
  author    = {Holler, S. and Butenweg, Christoph and Noh, S.-Y. and Meskouris, Konstantin},
  title     = {Numerical simulation of textile-reinforced concrete structures},
  series = {Proceedings of the Sixth International Conference on Computational Structures Technology : [Prague, Czech Republic, 4 - 6 September 2002] / ed. by B. H. V. Topping and Z. Bittnar. (Civil-Comp Press books on computational engineering)},
  booktitle = {Proceedings of the Sixth International Conference on Computational Structures Technology : [Prague, Czech Republic, 4 - 6 September 2002] / ed. by B. H. V. Topping and Z. Bittnar. (Civil-Comp Press books on computational engineering)},
  publisher = {Civil-Comp Press},
  address   = {Stirling},
  organization    = {International Conference on Computational Structures Technology <6, 2002, Prag>},
  isbn      = {0-948749-83-0},
  pages     = {287 -- 288},
  year      = {2002},
  language  = {en}
}
@article{KaulenSchwabedalSchneideretal.2022,
  author    = {Kaulen, Lars and Schwabedal, Justus T. C. and Schneider, Jules and Ritter, Philipp and Bialonski, Stephan},
  title     = {Advanced sleep spindle identification with neural networks},
  series = {Scientific Reports},
  volume    = {12},
  journal   = {Scientific Reports},
  number    = {Article number: 7686},
  publisher = {Springer Nature},
  address   = {London},
  issn      = {2045-2322},
  doi       = {10.1038/s41598-022-11210-y},
  pages     = {1 -- 10},
  year      = {2022},
  abstract  = {Sleep spindles are neurophysiological phenomena that appear to be linked to memory formation and other functions of the central nervous system, and that can be observed in electroencephalographic recordings (EEG) during sleep. Manually identified spindle annotations in EEG recordings suffer from substantial intra- and inter-rater variability, even if raters have been highly trained, which reduces the reliability of spindle measures as a research and diagnostic tool. The Massive Online Data Annotation (MODA) project has recently addressed this problem by forming a consensus from multiple such rating experts, thus providing a corpus of spindle annotations of enhanced quality. Based on this dataset, we present a U-Net-type deep neural network model to automatically detect sleep spindles. Our model's performance exceeds that of the state-of-the-art detector and of most experts in the MODA dataset. We observed improved detection accuracy in subjects of all ages, including older individuals whose spindles are particularly challenging to detect reliably. Our results underline the potential of automated methods to do repetitive cumbersome tasks with super-human performance.},
  language  = {en}
}
@article{TaddeiButenwegKlinkel2015,
  author    = {Taddei, Francesca and Butenweg, Christoph and Klinkel, S.},
  title     = {Parametric investigation of the soil-structure interaction effects on the dynamic behaviour of a shallow foundation supported wind turbine considering a layered soil},
  series = {Wind energy : an international journal for progress and applications in wind power conversion technology},
  volume    = {Volume 18},
  journal   = {Wind energy : an international journal for progress and applications in wind power conversion technology},
  number    = {Issue 3},
  publisher = {Wiley},
  address   = {Weinheim},
  issn      = {1099-1824 (E-Journal); 1095-4244 (Print)},
  doi       = {10.1002/we.1703},
  pages     = {399 -- 417},
  year      = {2015},
  language  = {en}
}
@inproceedings{ButenwegThierauf1997,
  author    = {Butenweg, Christoph and Thierauf, Georg},
  title     = {Optimum cost design of reinforced concrete structures using parallel computing},
  series = {Advances in computational mechanics with parallel and distributed processing : research papers presented at The First Euro-Conference on Parallel and Distributed Computing for Computational Mechanics, held at Lochinver, Scotland, between 26 April and 1 May 1997 / ed. by B. H. V. Topping},
  booktitle = {Advances in computational mechanics with parallel and distributed processing : research papers presented at The First Euro-Conference on Parallel and Distributed Computing for Computational Mechanics, held at Lochinver, Scotland, between 26 April and 1 May 1997 / ed. by B. H. V. Topping},
  publisher = {Saxe-Coburg Publication},
  address   = {Edinburgh},
  organization    = {Euro-Conference on Parallel and Distributed Computing for Computational Mechanics <1, 1997, Lochinver, Scotland>},
  isbn      = {0-948749-47-4},
  pages     = {197 -- 202},
  year      = {1997},
  language  = {en}
}
@inproceedings{ButenwegThierauf1998,
  author    = {Butenweg, Christoph and Thierauf, Georg},
  title     = {Optimum design of reinforced concrete structures},
  series = {Advances in computational structural mechanics : this volume contains a selection of papers presented at The First International Conference on Engineering Computational Technology and The Fourth International Conference on Computational Structures Technology, held in Edinburgh from 18-21 August 1998 / edited by B. H. V. Topping},
  booktitle = {Advances in computational structural mechanics : this volume contains a selection of papers presented at The First International Conference on Engineering Computational Technology and The Fourth International Conference on Computational Structures Technology, held in Edinburgh from 18-21 August 1998 / edited by B. H. V. Topping},
  publisher = {Civil-Comp Press},
  address   = {Edinburgh},
  organization    = {International Conference on Computational Structures Technology <4, 1998, Edinburgh>},
  isbn      = {0-948749-57-1},
  pages     = {447 -- 458},
  year      = {1998},
  language  = {en}
}
@inproceedings{RochefortVerverGrunendahletal.2005,
  author    = {Rochefort, E. de and Verver, M. and Grunendahl, A. and Mooi, H. and Butenweg, Christoph},
  title     = {Detailed modelling of the lumbar spine for investigation of low back pain},
  series = {Digital Human Modeling for Design and Engineering Symposium : Iowa City, Iowa June 14-16, 2005. (SAE technical papers series ; 2005-1-2716)},
  booktitle = {Digital Human Modeling for Design and Engineering Symposium : Iowa City, Iowa June 14-16, 2005. (SAE technical papers series ; 2005-1-2716)},
  publisher = {SAE International},
  address   = {Warrendale, Pa.},
  organization    = {Society of Automotive Engineers},
  issn      = {0096-736X},
  doi       = {10.4271/2005-01-2716},
  pages     = {1 -- 11},
  year      = {2005},
  language  = {en}
}
@article{HollerButenwegNohetal.2004,
  author    = {Holler, S. and Butenweg, Christoph and Noh, S.-Y. and Meskouris, Konstantin},
  title     = {Computational model of textile-reinforced concrete structures},
  series = {Computers \& structures : an international journal},
  volume    = {Volume 82},
  journal   = {Computers \& structures : an international journal},
  number    = {Issues 23-26},
  issn      = {1879-2243 (E-Journal); 0045-7949 (Print)},
  doi       = {10.1016/j.compstruc.2004.03.076},
  pages     = {1971 -- 1979},
  year      = {2004},
  language  = {en}
}
@article{MistlerButenwegMeskouris2006,
  author    = {Mistler, Michael and Butenweg, Christoph and Meskouris, Konstantin},
  title     = {Modelling methods of historic masonry buildings under seismic excitation},
  series = {Journal of seismology},
  volume    = {Volume 10},
  journal   = {Journal of seismology},
  number    = {No. 4},
  issn      = {1383-4649 (Print) ; 1573-157X (E-Journal)},
  doi       = {10.1007/s10950-006-9033-z},
  pages     = {497 -- 510},
  year      = {2006},
  language  = {en}
}
@article{MistlerAnthoineButenweg2007,
  author    = {Mistler, Michael and Anthoine, A. and Butenweg, Christoph},
  title     = {In-plane and out-of-plane homogenisation of masonry},
  series = {Computers \& structures},
  volume    = {Volume 85},
  journal   = {Computers \& structures},
  number    = {Issues 17-18},
  issn      = {1879-2243 (E-Journal); 0045-7949 (Print)},
  doi       = {10.1016/j.compstruc.2006.08.087},
  pages     = {1321 -- 1330},
  year      = {2007},
  language  = {en}
}
@inproceedings{SchmittRosinButenweg2018,
  author    = {Schmitt, Timo and Rosin, Julia and Butenweg, Christoph},
  title     = {Seismic Impact And Design Of Buried Pipelines},
  series = {16th European Conference on Earthquake Engineering, Thessaloniki, 18-21 June, 2018},
  booktitle = {16th European Conference on Earthquake Engineering, Thessaloniki, 18-21 June, 2018},
  pages     = {1 -- 12},
  year      = {2018},
  abstract  = {Seismic design of buried pipeline systems for energy and water supply is not only important for plant and operational safety but also for the maintenance of the supply infrastructure after an earthquake. The present paper shows special issues of the seismic wave impacts on buried pipelines, describes calculation methods, proposes approaches and gives calculation examples. This paper regards the effects of transient displacement differences and resulting tensions within the pipeline due to the wave propagation of the earthquake. However, the presented model can also be used to calculate fault rupture induced displacements. Based on a three-dimensional Finite Element Model parameter studies are performed to show the influence of several parameters such as incoming wave angle, wave velocity, backfill height and synthetic displacement time histories. The interaction between the pipeline and the surrounding soil is modeled with non-linear soil springs and the propagating wave is simulated affecting the pipeline punctually, independently in time and space. Special attention is given to long-distance heat pipeline systems. Here, in regular distances expansion bends are arranged to ensure movements of the pipeline due to high temperature. Such expansion bends are usually designed with small bending radii, which during the earthquake lead to high bending stresses in the cross-section of the pipeline. Finally, an interpretation of the results and recommendations are given for the most critical parameters.},
  language  = {en}
}
@inproceedings{RajanButenwegDalgueretal.2017,
  author    = {Rajan, S. and Butenweg, Christoph and Dalguer, L. A. and An, J. H. and Renault, P. and Klinkel, S.},
  title     = {Fragility curves for a three-storey reinforced concrete test structure of the international benchmark SMART 2013},
  series = {16th World Conference on Earthquake, 16WCEE 2017 Santiago Chile, January 9th to 13th 2017},
  booktitle = {16th World Conference on Earthquake, 16WCEE 2017 Santiago Chile, January 9th to 13th 2017},
  publisher = {Chilean Association on Seismology and Earthquake Engineering (ACHISINA)},
  year      = {2017},
  language  = {en}
}
@book{KlinkelButenwegLinetal.2014,
  author    = {Klinkel, Sven and Butenweg, Christoph and Lin, Gao and Holtschoppen, Britta},
  title     = {Seismic design of industrial facilities : Proceedings of the International Conference on Seismic Design of Industrial Facilities (SeDIF) / Sven Klinkel, Christoph Butenweg, Gao Lin, Britta Holtschoppen Editors},
  publisher = {Springer Vieweg},
  address   = {Wiesbaden},
  organization    = {International Conference on Seismic Design of Industrial Facilities <Aachen, 2013>},
  isbn      = {978-3-658-02809-1 (Print) ; 978-365-80281-0-7 (E-Book)},
  doi       = {10.1007/978-3-658-02810-7},
  pages     = {XIII, 450 S.},
  year      = {2014},
  language  = {en}
}
@inproceedings{ButenwegMarinkovicFehlingetal.2018,
  author    = {Butenweg, Christoph and Marinkovic, Marko and Fehling, Ekkehard and Pfetzing, Thomas and Kubalski, Thomas},
  title     = {Experimental and Numerical Investigations of Reinforced Concrete Frames with Masonry Infills under Combined In- and Out-of-plane Seismic Loading},
  series = {16th European Conference on Earthquake Engineering, Thessaloniki, 18-21 June, 2018},
  booktitle = {16th European Conference on Earthquake Engineering, Thessaloniki, 18-21 June, 2018},
  pages     = {1 -- 12},
  year      = {2018},
  language  = {en}
}
@techreport{ButenwegKaiser2014,
  author    = {Butenweg, Christoph and Kaiser, Diethelm},
  title     = {Seismic hazard harmonisation in Europe (SHARE) : DGEB-Workshop in Frankfurt a.M., Germany, 27. May 2014 / Christoph Butenweg, Diethelm Kaiser (editors)},
  publisher = {DGEB},
  address   = {Aachen},
  organization    = {Deutsche Gesellschaft f{\"u}r Erdbeben-Ingenieurwesen und Baudynamik},
  isbn      = {3-930108-12-7},
  pages     = {V, 117 S.},
  year      = {2014},
  language  = {en}
}
@inproceedings{MilkovaRosinButenwegetal.2018,
  author    = {Milkova, Kristina and Rosin, Julia and Butenweg, Christoph and Dumova-Jovanoska, Elena},
  title     = {Development of Seismic Vulnerability Curves for Region Specific Masonry Buildings},
  series = {16th European Conference on Earthquake Engineering, Thessaloniki, 18-21 June, 2018},
  booktitle = {16th European Conference on Earthquake Engineering, Thessaloniki, 18-21 June, 2018},
  pages     = {1 -- 10},
  year      = {2018},
  language  = {en}
}
@inproceedings{MichelButenwegKlinkel2018,
  author    = {Michel, Philipp and Butenweg, Christoph and Klinkel, Sven},
  title     = {Frequency Dependent Impedance Analysis of the Foundation-Soil-Systems of Onshore Wind Turbines},
  series = {16th European Conference on Earthquake Engineering, Thessaloniki, 18-21 June, 2018},
  booktitle = {16th European Conference on Earthquake Engineering, Thessaloniki, 18-21 June, 2018},
  pages     = {1 -- 13},
  year      = {2018},
  language  = {en}
}
@article{DigelTemizArtmannNishikawaetal.2004,
  author    = {Digel, Ilya and Temiz Artmann, Ayseg{\"u}l and Nishikawa, K. and Artmann, Gerhard},
  title     = {Cluster air-ion effects on bacteria and moulds},
  series = {Biomedizinische Technik. 49 (2004), H. Erg.-Bd. 2},
  journal   = {Biomedizinische Technik. 49 (2004), H. Erg.-Bd. 2},
  isbn      = {0932-4666},
  pages     = {1040 -- 1041},
  year      = {2004},
  language  = {en}
}
@inproceedings{RosinMykoniouButenweg2017,
  author    = {Rosin, J. and Mykoniou, K. and Butenweg, Christoph},
  title     = {Analysis Of Base Isolated Liquid Storage Tanks With 3D Fsi-Analysis As Well As Simplified Approaches},
  series = {16th World Conference on Earthquake Engineering, 16WCEE 2017 Santiago Chile, January 9th to 13th 2017},
  booktitle = {16th World Conference on Earthquake Engineering, 16WCEE 2017 Santiago Chile, January 9th to 13th 2017},
  publisher = {Chilean Association on Seismology and Earthquake Engineering (ACHISINA)},
  pages     = {1 -- 14},
  year      = {2017},
  abstract  = {Tanks are preferably designed, for cost-saving reasons, as circular, cylindrical, thin-walled shells. In case of seismic excitation, these constructions are highly vulnerable to stability failures. An earthquake-resistant design of rigidly supported tanks for high seismic loading demands, however, uneconomic wall thicknesses. A cost-effective alternative can be provided by base isolation systems. In this paper, a simplified seismic design procedure for base isolated tanks is introduced, by appropriately modifying the standard mechanical model for flexible, rigidly supported tanks. The non-linear behavior of conventional base isolation systems becomes an integral part of a proposed simplified process, which enables the assessment of the reduced hydrodynamic forces acting on the tank walls and the corresponding stress distribution. The impulsive and convective actions of the liquid are taken into account. The validity of this approach is evaluated by employing a non-linear fluid-structure interaction algorithm of finite element method. Special focus is placed on the boundary conditions imposed from the base isolation and the resulting hydrodynamic pressures. Both horizontal and vertical component of ground motion are considered in order to study the principal effects of the base isolation on the pressure distribution of the tank walls. The induced rocking effects associated with elastomeric bearings are discussed. The results manifest that base isolated tanks can be designed for seismic loads by means of the proposed procedure with sufficient accuracy, allowing to dispense with numerically expensive techniques.},
  language  = {en}
}
@inproceedings{ButenwegMarinkovic2018,
  author    = {Butenweg, Christoph and Marinkovic, Marko},
  title     = {Damage reduction system for masonry infill walls under seismic loading},
  series = {ce/papers},
  volume    = {2},
  booktitle = {ce/papers},
  number    = {4},
  publisher = {Ernst \& Sohn Verlag},
  address   = {Berlin},
  doi       = {10.1002/cepa.863},
  pages     = {267 -- 273},
  year      = {2018},
  abstract  = {Reinforced concrete (RC) frames with masonry infills are frequently used in seismic regions all over the world. Generally masonry infills are considered as nonstructural elements and thus are typically neglected in the design process. However, the observations made after strong earthquakes have shown that masonry infills can modify the dynamic behavior of the structure significantly. The consequences were total collapses of buildings and loss of human lives. This paper presents the new system INODIS (Innovative Decoupled Infill System) developed within the European research project INSYSME (Innovative Systems for Earthquake Resistant Masonry Enclosures in RC Buildings). INODIS decouples the frame and the masonry infill by means of special U-shaped rubbers placed in between frame and infill. The effectiveness of the system was investigated by means of full scale tests on RC frames with masonry infills subjected to in-plane and out-of-plane loading. Furthermore small specimen tests were conducted to determine material characteristics of the components and the resistances of the connections. Finally, a micromodel was developed to simulate the in-plane behavior of RC frames infilled with AAC blocks with and without installation of the INODIS system.},
  language  = {en}
}
@inproceedings{MistlerButenwegAnthoine2004,
  author    = {Mistler, M. and Butenweg, Christoph and Anthoine, A.},
  title     = {Evaluation of the failure criterion for masonry by homogenisation},
  series = {Proceedings of the Seventh International Conference on Computational Structures Technology : [Lisbon, Portugal, 7 - 9 September 2004] / ed. by B. H. V. Topping and C.A. Mota Soares},
  booktitle = {Proceedings of the Seventh International Conference on Computational Structures Technology : [Lisbon, Portugal, 7 - 9 September 2004] / ed. by B. H. V. Topping and C.A. Mota Soares},
  publisher = {Civil-Comp Press},
  address   = {Stirling},
  organization    = {International Conference on Computational Structures Technology <7, 2004, Lissabon>},
  isbn      = {0-948749-95-4},
  doi       = {10.4203/ccp.79.201},
  pages     = {16 Seiten},
  year      = {2004},
  language  = {en}
}
@article{DigelTemizArtmannNishikawaetal.2005,
  author    = {Digel, Ilya and Temiz Artmann, Ayseg{\"u}l and Nishikawa, K. and Cook, M.},
  title     = {Bactericidal effects of plasma-generated cluster ions},
  series = {Medical and Biological Engineering and Computing. 43 (2005), H. 6},
  journal   = {Medical and Biological Engineering and Computing. 43 (2005), H. 6},
  isbn      = {1741-0444},
  pages     = {800 -- 807},
  year      = {2005},
  language  = {en}
}
@inproceedings{KubalskiMarinkovićButenweg2016,
  author    = {Kubalski, T. and Marinković, Marko and Butenweg, Christoph},
  title     = {Numerical investigation of masonry infilled R.C. frames},
  series = {Brick and Block Masonry. Proceedings of the 16th International Brick and Block Masonry Conference, Padova, Italy, 26-30 June 2016},
  booktitle = {Brick and Block Masonry. Proceedings of the 16th International Brick and Block Masonry Conference, Padova, Italy, 26-30 June 2016},
  editor    = {Modena, Claudio},
  publisher = {CRC Press},
  address   = {Leiden},
  isbn      = {9781315374963},
  pages     = {1219 -- 1226},
  year      = {2016},
  language  = {en}
}
@inproceedings{MarinkovicButenweg2018,
  author    = {Marinkovic, Marko and Butenweg, Christoph},
  title     = {Innovative System for Earthquake Resistant Masonry Infill Walls},
  series = {16th European Conference on Earthquake Engineering, Thessaloniki, 18-21 June, 2018},
  booktitle = {16th European Conference on Earthquake Engineering, Thessaloniki, 18-21 June, 2018},
  pages     = {1 -- 12},
  year      = {2018},
  language  = {en}
}
@article{DigelKernGeenenetal.2020,
  author    = {Digel, Ilya and Kern, Inna and Geenen, Eva-Maria and Akimbekov, Nuraly S.},
  title     = {Dental plaque removal by ultrasonic toothbrushes},
  series = {dentistry journal},
  volume    = {8},
  journal   = {dentistry journal},
  number    = {28},
  publisher = {MDPI},
  address   = {Basel},
  issn      = {2304-6767},
  doi       = {10.3390/dj8010028},
  pages     = {1 -- 13},
  year      = {2020},
  abstract  = {With the variety of toothbrushes on the market, the question arises, which toothbrush is best suited to maintain oral health? This thematic review focuses first on plaque formation mechanisms and then on the plaque removal effectiveness of ultrasonic toothbrushes and their potential in preventing oral diseases like periodontitis, gingivitis, and caries. We overviewed the physical effects that occurred during brushing and tried to address the question of whether ultrasonic toothbrushes effectively reduced the microbial burden by increasing the hydrodynamic forces. The results of published studies show that electric toothbrushes, which combine ultrasonic and sonic (or acoustic and mechanic) actions, may have the most promising effect on good oral health. Existing ultrasonic/sonic toothbrush models do not significantly differ regarding the removal of dental biofilm and the reduction of gingival inflammation compared with other electrically powered toothbrushes, whereas the manual toothbrushes show a lower effectiveness.},
  language  = {en}
}
@article{RossiParisiCasarietal.2019,
  author    = {Rossi, Leonardo and Parisi, Davide and Casari, Chiara and Montanari, Luca and Ruggieri, Gabriella and Holtschoppen, Britta and Butenweg, Christoph},
  title     = {Empirical Data about Direct Economic Consequences of Emilia-Romagna 2012 Earthquake on Long-Span-Beam Buildings},
  series = {Earthquake Spectra},
  volume    = {35},
  journal   = {Earthquake Spectra},
  number    = {4},
  issn      = {1944-8201},
  doi       = {10.1193/100118EQS224DP},
  pages     = {1979 -- 2001},
  year      = {2019},
  language  = {en}
}
@article{DigelAkimbekovTuralievaetal.2013,
  author    = {Digel, Ilya and Akimbekov, Nuraly S. and Turalieva, M. and Mansurov, Z. and Temiz Artmann, Ayseg{\"u}l and Eshibaev, A. and Zhubanova, A.},
  title     = {Usage of Carbonized Plant Wastes for Purification of Aqueous Solutions},
  series = {Journal of Industrial Technology and Engineering},
  volume    = {2},
  journal   = {Journal of Industrial Technology and Engineering},
  number    = {07},
  pages     = {47 -- 54},
  year      = {2013},
  language  = {en}
}
@inproceedings{GierseKraemerDaabetal.2013,
  author    = {Gierse, Andreas and Kr{\"a}mer, Stefan and Daab, Dominique J. and Hessel, Joana and Baader, Fabian and M{\"u}ller, Brigitte S. and Wagner, Tobias and Gdalewitsch, Georg and Plescher, Engelbert and Pf{\"u}tzenreuter, Lysan},
  title     = {Experimental in-flight modal-analysis of a sounding rocket structure},
  series = {21st ESA Symposium on Rocket and Ballon related Research},
  booktitle = {21st ESA Symposium on Rocket and Ballon related Research},
  isbn      = {9789290922858},
  pages     = {341 -- 346},
  year      = {2013},
  language  = {en}
}
@inproceedings{GrundmannBauerBieleetal.2018,
  author    = {Grundmann, Jan Thimo and Bauer, Waldemar and Biele, Jens and Boden, Ralf and Ceriotti, Matteo and Cordero, Federico and Dachwald, Bernd and Dumont, Etienne and Grimm, Christian and Herč{\´i}k, David and Herique, Alain and Ho, Tra-Mi and Jahnke, Rico and Koch, Aaron and Kofman, Wlodek and Koncz, Alexander and Krause, Christian and Lange, Caroline and Lichtenheldt, Roy and Maiwald, Volker and Mikschl, Tobias and Mikulz, Eugen and Montenegro, Sergio and Pelivan, Ivanka and Peloni, Alessandro and Plettemeier, Dirk and Quantius, Dominik and Reershemius, Siebo and Renger, Thomas and Riemann, Johannes and Ruffer, Michael and Sasaki, Kaname and Schmitz, Nicole and Seboldt, Wolfgang and Seefeldt, Patric and Spietz, Peter and Spr{\"o}witz, Tom and Sznajder, Maciej and Tardivel, Simon and Toth, Norbert and Wejmo, Elisabet and Wolff, Friederike and Ziach, Christian},
  title     = {Efficient massively parallel prospection for ISRU by multiple near-earth asteroid rendezvous using near-term solar sails and'now-term'small spacecraft solutions},
  series = {2nd Asteroid Science Intersections with In-Space Mine Engineering - ASIME 2018},
  booktitle = {2nd Asteroid Science Intersections with In-Space Mine Engineering - ASIME 2018},
  pages     = {1 -- 33},
  year      = {2018},
  abstract  = {Physical interaction with small solar system bodies (SSSB) is key for in-situ resource utilization (ISRU). The design of mining missions requires good understanding of SSSB properties, including composition, surface and interior structure, and thermal environment. But as the saying goes "If you've seen one asteroid, you've seen one Asteroid": Although some patterns may begin to appear, a stable and reliable scheme of SSSB classification still has to be evolved. Identified commonalities would enable generic ISRU technology and spacecraft design approaches with a high degree of re-use. Strategic approaches require much broader in-depth characterization of the SSSB populations of interest to the ISRU community. The DLR-ESTEC GOSSAMER Roadmap Science Working Groups identified target-flexible Multiple Near-Earth asteroid (NEA) Rendezvous (MNR) as one of the missions only feasible with solar sail propulsion, showed the ability to access any inclination and a wide range of heliocentric distances as well as continuous operation close to Earth's orbit where low delta-v objects reside.},
  language  = {en}
}
@inproceedings{SeboldtDachwald2003,
  author    = {Seboldt, Wolfgang and Dachwald, Bernd},
  title     = {Solar sails for near-term advanced scientific deep space missions},
  series = {Proceedings of the 8th International Workshop on Combustion and Propulsion},
  booktitle = {Proceedings of the 8th International Workshop on Combustion and Propulsion},
  pages     = {14 Seiten},
  year      = {2003},
  abstract  = {Solar sails are propelled in space by reflecting solar photons off large mirroring surfaces, thereby transforming the momentum of the photons into a propulsive force. This innovative concept for low-thrust space propulsion works without any propellant and thus provides a wide range of opportunities for highenergy low-cost missions. Offering an efficient way of propulsion, solar sailcraft could close a gap in transportation options for highly demanding exploration missions within our solar system and even beyond. On December 17th, 1999, a significant step was made towards the realization of this technology: a lightweight solar sail structure with an area of 20 m × 20 m was successfully deployed on ground in a large facility at the German Aerospace Center (DLR) at Cologne. The deployment from a package of 60 cm × 60 cm × 65 cm with a total mass of less than 35 kg was achieved using four extremely light-weight carbon fiber reinforced plastics (CFRP) booms with a specific mass of 100 g/m. The paper briefly reviews the basic principles of solar sails as well as the technical concept and its realization in the ground demonstration experiment, performed in close cooperation between DLR and ESA. Next possible steps are outlined. They could comprise the in-orbit demonstration of the sail deployment on the upper stage of a low-cost rocket and the verification of the propulsion concept by an autonomous and free flying solar sail in the frame of a scientific mission. It is expected that the present design could be extended to sail sizes of about (40 m)2 up to even (70 m)2 without significant mass penalty. With these areas, the maximum achievable thrust at 1 AU would range between 10 and 40 mN - comparable to some electric thrusters. Such prototype sails with a mass between 50 and 150 kg plus a micro-spacecraft of 50 to 250 kg would have a maximum acceleration in the order of 0.1 mm/s2 at 1 AU, corresponding to a maximum ∆V-capability of about 3 km/s per year. Two near/medium-term mission examples to a near-Earth asteroid (NEA) will be discussed: a rendezvous mission and a sample return mission.},
  language  = {en}
}
@article{ScheeleOertelBongaertsetal.2013,
  author    = {Scheele, Sandra and Oertel, Dan and Bongaerts, Johannes and Evers, Stefan and Hellmuth, Hendrik and Maurer, Karl-Heinz and Bott, Michael and Freudl, Roland},
  title     = {Secretory production of an FAD cofactor-containing cytosolic enzyme (sorbitol-xylitol oxidase from Streptomyces coelicolor) using the twin-arginine translocation (Tat) pathway of Corynebacterium glutamicum},
  series = {Microbial biotechnology},
  journal   = {Microbial biotechnology},
  publisher = {Wiley-Blackwell},
  address   = {Oxford},
  issn      = {1751-7915},
  pages     = {202 -- 206},
  year      = {2013},
  language  = {en}
}
@incollection{Dachwald2017,
  author    = {Dachwald, Bernd},
  title     = {Light propulsion systems for spacecraft},
  series = {Optical nano and micro actuator technology},
  booktitle = {Optical nano and micro actuator technology},
  editor    = {Knopf, George K. and Otani, Yukitoshi},
  publisher = {CRC Press},
  address   = {Boca Raton},
  isbn      = {9781315217628 (eBook)},
  pages     = {577 -- 598},
  year      = {2017},
  language  = {en}
}
@article{DigelKayserArtmann2008,
  author    = {Digel, Ilya and Kayser, Peter and Artmann, Gerhard},
  title     = {Molecular processes in biological thermosensation},
  series = {Journal of Biophysics. 2008 (2008)},
  journal   = {Journal of Biophysics. 2008 (2008)},
  isbn      = {1687-8000},
  pages     = {1 -- 9},
  year      = {2008},
  language  = {en}
}
@article{AlexyukBogoyavlenskiyAlexyuketal.2021,
  author    = {Alexyuk, Madina and Bogoyavlenskiy, Andrey and Alexyuk, Pavel and Moldakhanov, Yergali and Berezin, Vladimir and Digel, Ilya},
  title     = {Epipelagic microbiome of the Small Aral Sea: Metagenomic structure and ecological diversity},
  series = {MicrobiologyOpen},
  volume    = {10},
  journal   = {MicrobiologyOpen},
  number    = {1},
  publisher = {Wiley},
  address   = {Weinheim},
  issn      = {2045-8827},
  doi       = {10.1002/mbo3.1142},
  pages     = {1 -- 10},
  year      = {2021},
  abstract  = {Microbial diversity studies regarding the aquatic communities that experienced or are experiencing environmental problems are essential for the comprehension of the remediation dynamics. In this pilot study, we present data on the phylogenetic and ecological structure of microorganisms from epipelagic water samples collected in the Small Aral Sea (SAS). The raw data were generated by massive parallel sequencing using the shotgun approach. As expected, most of the identified DNA sequences belonged to Terrabacteria and Actinobacteria (40\% and 37\% of the total reads, respectively). The occurrence of Deinococcus-Thermus, Armatimonadetes, Chloroflexi in the epipelagic SAS waters was less anticipated. Surprising was also the detection of sequences, which are characteristic for strict anaerobes—Ignavibacteria, hydrogen-oxidizing bacteria, and archaeal methanogenic species. We suppose that the observed very broad range of phylogenetic and ecological features displayed by the SAS reads demonstrates a more intensive mixing of water masses originating from diverse ecological niches of the Aral-Syr Darya River basin than presumed before.},
  language  = {en}
}
@article{AkimbekovMansurovJandosovetal.2013,
  author    = {Akimbekov, Nuraly S. and Mansurov, Zulkhair and Jandosov, J. and Digel, Ilya and Gossmann, Matthias and Artmann, Gerhard and Temiz Artmann, Ayseg{\"u}l and Zhubanova, Azhar A.},
  title     = {Wound healing activity of carbonized rice husk},
  publisher = {Trans Tech Publications, Switzerland},
  address   = {B{\"a}ch},
  year      = {2013},
  abstract  = {The carbonized rice husk (CRH) was evaluated for its wound healing activity in rats using excision models. In this study, the influences of CRH on wound healing in rat skin in vivo and cellular behavior of human dermal fibroblasts in vitro were investigated. The obtained results showed that the CRH treatment promoted wound epithelization in rats and exhibited moderate inhibition of cell proliferation in vitro. CRH with lanolin oil treated wounds were found to epithelize faster as compared to controls.},
  subject      = {Wundheilung},
  language  = {en}
}
@inproceedings{DigelTemizArtmannNojimaetal.2003,
  author    = {Digel, Ilya and Temiz Artmann, Ayseg{\"u}l and Nojima, H. and Artmann, Gerhard},
  title     = {Some peculiarities of application of cluster ions generated by plasma in respect of indoor air purification :[abstract]},
  year      = {2003},
  abstract  = {Recently, the SHARP Corporation, Japan, has developed the world's first "Plasma Cluster Ions (PCI)" air purification technology using plasma discharge to generate cluster ions. The new plasma cluster device releases positive and negative ions into the air, which are able to decompose and deactivate harmful airborne substances by chemical reactions. Because cluster ions consist of positive and negative ions that normally exist in the natural world, they are completely harmless and safe to humans. The amount of ozone generated by cluster ions is less than 0.01 ppm, which is significantly less than the 0.05-ppm standard for industrial operations and consumer electronics. This amount, thus, has no harming effects whatsoever on the human body. But particular properties and chemical processes in PCI treatment are still under study. It has been shown that PCI in most cases show strongly pronounced irreversible killing effects in respect of airborne microflora due to free-radical induced reactions and can be considered as a potent technology to disinfect both home, medical and industrial appliances.},
  subject      = {Clusterion},
  language  = {en}
}
@inproceedings{KoenigWolf2018,
  author    = {K{\"o}nig, Johannes Alexander and Wolf, Martin R.},
  title     = {Cybersecurity awareness training provided by the competence developing game GHOST},
  series = {ACHI 2018 : The Eleventh International Conference on Advances in Computer-Human Interactions},
  booktitle = {ACHI 2018 : The Eleventh International Conference on Advances in Computer-Human Interactions},
  isbn      = {978-1-61208-616-3},
  pages     = {81 -- 87},
  year      = {2018},
  abstract  = {This paper introduces a Competence Developing Game (CDG) for the purpose of a cybersecurity awareness training for businesses. The target audience will be discussed in detail to understand their requirements. It will be explained why and how a mix of business simulation and serious game meets these stakeholder requirements. It will be shown that a tablet and touchscreen based approach is the most suitable solution. In addition, an empirical study will be briefly presented. The study was carried out to examine how an interaction system for a 3D-tablet based CDG has to be designed, to be manageable for non-game experienced employees. Furthermore, it will be explained which serious content is necessary for a Cybersecurity awareness training CDG and how this content is wrapped in the game},
  language  = {en}
}
@inproceedings{HeinzOertelBung2010,
  author    = {Heinz, G. and Oertel, Mario and Bung, Daniel Bernhard},
  title     = {Investigations on a cooling water system for a gas tubine facility concerning air vortexes and sediment transport},
  series = {Hydraulic structures: useful water harvesting systems or relics? : Third International Junior Researcher and Engineer Workshop on Hydraulic Structures (IJREWHS'10) : Edinburgh, Scotland, U.K., 2-3 May 2010},
  booktitle = {Hydraulic structures: useful water harvesting systems or relics? : Third International Junior Researcher and Engineer Workshop on Hydraulic Structures (IJREWHS'10) : Edinburgh, Scotland, U.K., 2-3 May 2010},
  editor    = {Janssen, Robert},
  publisher = {School of Civil Engineering, The University of Queensland},
  address   = {Brisbane},
  organization    = {International Junior Researcher and Engineer Workshop on Hydraulic Structures <3, 2010, Edinburgh>},
  isbn      = {9781742720159},
  pages     = {109 -- 116},
  year      = {2010},
  language  = {en}
}
@inproceedings{ButenwegNorda2013,
  author    = {Butenweg, Christoph and Norda, Hannah},
  title     = {Nonlinear analysis of masonry structures according to Eurocode 8},
  series = {Proceedings - Vienna Congress on Recent Advances in Earthquake Engineering and Structural Dynamics 2013 (VEESD 2013)},
  booktitle = {Proceedings - Vienna Congress on Recent Advances in Earthquake Engineering and Structural Dynamics 2013 (VEESD 2013)},
  editor    = {Adam, Christoph and Heuer, Rudolf and Lenhardt, Wolfgang and Schranz, Christian},
  isbn      = {978-3-902749-04-8},
  year      = {2013},
  language  = {en}
}
@inproceedings{ValeroBungErpicumetal.2017,
  author    = {Valero, Daniel and Bung, Daniel Bernhard and Erpicum, Sebastien and Dewals, Benjamin},
  title     = {Numerical study of turbulent oscillations around a cylinder: RANS capabilities and sensitivity analysis},
  series = {Proceedings of the 37th IAHR World Congress August 13 - 18, 2017, Kuala Lumpur, Malaysia},
  booktitle = {Proceedings of the 37th IAHR World Congress August 13 - 18, 2017, Kuala Lumpur, Malaysia},
  issn      = {2521-716X},
  pages     = {3126 -- 3135},
  year      = {2017},
  language  = {en}
}
@incollection{AkimbekovZhanadilovnaUalievaetal.2020,
  author    = {Akimbekov, Nuraly S. and Zhanadilovna, Abdieva G. and Ualieva, Perizat S. and Abaihanovna, Zhusipova D. and Digel, Ilya and Savitskaya, Irina S. and Zhubanova, Azhar Achmet},
  title     = {Functionalization of Carbon Based Wound Dressings with Antimicrobial Phytoextracts for Bioactive Treatment of Septic Wounds},
  series = {Carbon Nanomaterials in Biomedicine and the Environment},
  booktitle = {Carbon Nanomaterials in Biomedicine and the Environment},
  publisher = {Jenny Stanford Publishing},
  address   = {Singapore},
  isbn      = {978-981-4800-27-3},
  doi       = {10.1201/9780429428647-11},
  pages     = {211 -- 228},
  year      = {2020},
  abstract  = {The treatment of septic wounds with curative dressings based on biocomposites containing sage and marigold phytoextracts was effective in in vitro and in vivo experiments. These dressings caused the purification of the wound surface from purulent-necrotic masses three days earlier than in the other experimental groups. The consequence of an increase in incidents of severe course of the wound and the observed tendency to increase the number of adverse effects is the development of long-term recurrent wound processes. To treat purulent wounds, the following tactics were used: The purulent wounds of animals were covered with the examined wound dressing, and then the next day samples were taken, the procedure was performed once in 2 days. To obtain the active nanostructured sorbents such as carbonized rice husks, they are functionalized with biologically active components possessing antimicrobial, anti-inflammatory, antitoxic, immunomodulating, antiallergic and other types of properties.},
  language  = {en}
}
@incollection{SavitskayaKistaubayevaAkimbekovetal.2020,
  author    = {Savitskaya, Irina S. and Kistaubayeva, Aida S. and Akimbekov, Nuraly S. and Digel, Ilya and Shokatayeva, Dina and Zhubanova, Azhar Achmet},
  title     = {Prospective Use of Probiotics Immobilized on Sorbents with Nanostructured Surfaces},
  series = {Carbon Nanomaterials in Biomedicine and the Environment},
  booktitle = {Carbon Nanomaterials in Biomedicine and the Environment},
  publisher = {Jenny Stanford Publishing},
  address   = {Singapore},
  isbn      = {978-981-4800-27-3},
  doi       = {10.1201/9780429428647-12},
  pages     = {229 -- 267},
  year      = {2020},
  abstract  = {Activated carbons are known as excellent adsorbents. Their applications include the adsorptive removal of color, odor, taste, undesirable organic and inorganic pollutants from drinking and waste water; air purification in inhabited spaces; purification of many chemicals, pharmaceutical products and many others. This chapter elucidates the role of normal microflora in the maintenance of human health and presents materials on possible clinical displays of microecological infringements and ways of their correction. It presents new developments concerning new probiotics with immobilized Lactobacillus and Bacillus. The chapter considers the mechanisms of the intestine disbacteriosis correction by sorbed probiotics. It demonstrates the advantages and creation prospects of immobilized probiotics developed on the basis of carbonized rice husk. There are great prospects for the development of medical biotechnology due to use of carbon sorbents with a nanostructured surface. Microbial communities form a biocenosis of the biotope and together with the host organism create permanent or temporary ecosystems.},
  language  = {en}
}