@article{SchiedermeierRettnerHeilmannetal.2019,
  author    = {Schiedermeier, Maximilian and Rettner, Cornelius and Heilmann, Marcel and Schneider, Felix and Marz, Martin},
  title     = {Interference of automotive HV-DC-systems by traction voltage-source-inverters (VSI)},
  series = {2019 IEEE Transportation Electrification Conference (ITEC-India)},
  journal   = {2019 IEEE Transportation Electrification Conference (ITEC-India)},
  publisher = {IEEE},
  address   = {New York},
  doi       = {10.1109/ITEC-India48457.2019.ITECINDIA2019-37},
  pages     = {1 -- 6},
  year      = {2019},
  language  = {en}
}
@article{HoevelerBauknechtWolfetal.2020,
  author    = {Hoeveler, B. and Bauknecht, Andr{\´e} and Wolf, C. Christian and Janser, Frank},
  title     = {Wind-Tunnel Study of a Wing-Embedded Lifting Fan Remaining Open in Cruise Flight},
  series = {Journal of Aircraft},
  volume    = {57},
  journal   = {Journal of Aircraft},
  number    = {4},
  publisher = {AIAA},
  address   = {Reston, Va.},
  issn      = {1533-3868},
  doi       = {10.2514/1.C035422},
  year      = {2020},
  abstract  = {It is investigated whether a nonrotating lifting fan remaining uncovered during cruise flight, as opposed to being covered by a shutter system, can be realized with limited additional drag and loss of lift during cruise flight. A wind-tunnel study of a wing-embedded lifting fan has been conducted at the Side Wind Test Facility G{\"o}ttingen of DLR, German Aerospace Center in G{\"o}ttingen using force, pressure, and stereoscopic particle image velocimetry techniques. The study showed that a step on the lower side of the wing in front of the lifting fan duct increases the lift-to-drag ratio of the whole model by up to 25\% for all positive angles of attack. Different sizes and inclinations of the step had limited influence on the surface pressure distribution. The data indicate that these parameters can be optimized to maximize the lift-to-drag ratio. A doubling of the curvature radius of the lifting fan duct inlet lip on the upper side of the wing affected the lift-to-drag ratio by less than 1\%. The lifting fan duct inlet curvature can therefore be optimized to maximize the vertical fan thrust of the rotating lifting fan during hovering without affecting the cruise flight performance with a nonrotating fan.},
  language  = {en}
}
@article{ChoiFelderFelderetal.2020,
  author    = {Choi, Chang-Hoon and Felder, Tim and Felder, J{\"o}rg and Tellmann, Lutz and Hong, Suk-Min and Wegener, Hans-Peter and Shah, N Jon and Ziemons, Karl},
  title     = {Design, evaluation and comparison of endorectal coils for hybrid MR-PET imaging of the prostate},
  series = {Physics in Medicine \& Biology},
  volume    = {65},
  journal   = {Physics in Medicine \& Biology},
  number    = {11},
  publisher = {IOP},
  address   = {Bristol},
  issn      = {0031-9155},
  doi       = {10.1088/1361-6560/ab87f8},
  year      = {2020},
  abstract  = {Prostate cancer is one of the most common cancers among men and its early detection is critical for its successful treatment. The use of multimodal imaging, such as MR-PET, is most advantageous as it is able to provide detailed information about the prostate. However, as the human prostate is flexible and can move into different positions under external conditions, it is important to localise the focused region-of-interest using both MRI and PET under identical circumstances. In this work, we designed five commonly used linear and quadrature radiofrequency surface coils suitable for hybrid MR-PET use in endorectal applications. Due to the endorectal design and the shielded PET insert, the outer face of the coils investigated was curved and the region to be imaged was outside the volume of the coil. The tilting angles of the coils were varied with respect to the main magnetic field direction. This was done to approximate the various positions from which the prostate could be imaged. The transmit efficiencies and safety excitation efficiencies from simulations, together with the signal-to-noise ratios from the MR images were calculated and analysed. Overall, it was found that the overlapped loops driven in quadrature were superior to the other types of coils we tested. In order to determine the effect of the different coil designs on PET, transmission scans were carried out, and it was observed that the differences between attenuation maps with and without the coils were negligible. The findings of this work can provide useful guidance for the integration of such coil designs into MR-PET hybrid systems in the future.},
  language  = {en}
}
@article{KhayyamJamaliBabHadiasharetal.2020,
  author    = {Khayyam, Hamid and Jamali, Ali and Bab-Hadiashar, Alireza and Esch, Thomas and Ramakrishna, Seeram and Jalili, Mahdi and Naebe, Minoo},
  title     = {A Novel Hybrid Machine Learning Algorithm for Limited and Big Data Modeling with Application in Industry 4.0},
  series = {IEEE Access},
  volume    = {8},
  journal   = {IEEE Access},
  number    = {Art. 9108222},
  publisher = {IEEE},
  address   = {New York, NY},
  issn      = {2169-3536},
  doi       = {10.1109/ACCESS.2020.2999898},
  pages     = {111381 -- 111393},
  year      = {2020},
  abstract  = {To meet the challenges of manufacturing smart products, the manufacturing plants have been radically changed to become smart factories underpinned by industry 4.0 technologies. The transformation is assisted by employment of machine learning techniques that can deal with modeling both big or limited data. This manuscript reviews these concepts and present a case study that demonstrates the use of a novel intelligent hybrid algorithms for Industry 4.0 applications with limited data. In particular, an intelligent algorithm is proposed for robust data modeling of nonlinear systems based on input-output data. In our approach, a novel hybrid data-driven combining the Group-Method of Data-Handling and Singular-Value Decomposition is adapted to find an offline deterministic model combined with Pareto multi-objective optimization to overcome the overfitting issue. An Unscented-Kalman-Filter is also incorporated to update the coefficient of the deterministic model and increase its robustness against data uncertainties. The effectiveness of the proposed method is examined on a set of real industrial measurements.},
  language  = {en}
}
@article{GronsfeldJoachimMalecha2019,
  author    = {Gronsfeld, Richard and Joachim, Klubert and Malecha, Hartmut},
  title     = {3-D-Visualisierung von vorhandenen Staubauwerken zur holistischen Planung und {\"U}berwachung},
  series = {Wasserwirtschaft},
  volume    = {109},
  journal   = {Wasserwirtschaft},
  number    = {5},
  publisher = {Springer},
  address   = {Berlin},
  issn      = {2192-8762},
  doi       = {10.1007/s35147-019-0075-x},
  pages     = {82 -- 85},
  year      = {2019},
  language  = {de}
}
@article{SvaneborgKarimiVarzanehHojdisetal.2016,
  author    = {Svaneborg, Carsten and Karimi-Varzaneh, Hossein Ali and Hojdis, Nils and Fleck, Franz and Everaers, Ralf},
  title     = {Multiscale approach to equilibrating model polymer melts},
  series = {Physical Review E},
  volume    = {94},
  journal   = {Physical Review E},
  number    = {032502},
  publisher = {AIP Publishing},
  address   = {Melville, NY},
  issn      = {2470-0053},
  doi       = {10.1103/PhysRevE.94.032502},
  year      = {2016},
  abstract  = {We present an effective and simple multiscale method for equilibrating Kremer Grest model polymer melts of varying stiffness. In our approach, we progressively equilibrate the melt structure above the tube scale, inside the tube and finally at the monomeric scale. We make use of models designed to be computationally effective at each scale. Density fluctuations in the melt structure above the tube scale are minimized through a Monte Carlo simulated annealing of a lattice polymer model. Subsequently the melt structure below the tube scale is equilibrated via the Rouse dynamics of a force-capped Kremer-Grest model that allows chains to partially interpenetrate. Finally the Kremer-Grest force field is introduced to freeze the topological state and enforce correct monomer packing. We generate 15 melts of 500 chains of 10.000 beads for varying chain stiffness as well as a number of melts with 1.000 chains of 15.000 monomers. To validate the equilibration process we study the time evolution of bulk, collective, and single-chain observables at the monomeric, mesoscopic, and macroscopic length scales. Extension of the present method to longer, branched, or polydisperse chains, and/or larger system sizes is straightforward.},
  language  = {en}
}
@article{SchwabHojdisLacayoetal.2016,
  author    = {Schwab, Lukas and Hojdis, Nils and Lacayo, Jorge and Wilhelm, Manfred},
  title     = {Fourier-Transform Rheology of Unvulcanized, Carbon Black Filled Styrene Butadiene Rubber},
  series = {Macromolecular Materials and Engineering},
  volume    = {301},
  journal   = {Macromolecular Materials and Engineering},
  number    = {4},
  publisher = {Wiley-VCH},
  address   = {Weinheim},
  issn      = {1439-2054},
  doi       = {10.1002/mame.201500356},
  pages     = {457 -- 468},
  year      = {2016},
  abstract  = {Rubber materials filled with reinforcing fillers display nonlinear rheological behavior at small strain amplitudes below γ0 < 0.1. Nevertheless, rheological data are analyzed mostly in terms of linear parameters, such as shear moduli (G′, G″), which loose their physical meaning in the nonlinear regime. In this work styrene butadiene rubber filled with carbon black (CB) under large amplitude oscillatory shear (LAOS) is analyzed in terms of the nonlinear parameter I3/1. Three different CB grades are used and the filler load is varied between 0 and 70 phr. It is found that I3/1(φ) is most sensitive to changes of the total accessible filler surface area at low strain amplitudes (γ0 = 0.32). The addition of up to 70 phr CB leads to an increase of I3/1(φ) by a factor of more than ten. The influence of the measurement temperature on I3/1 is pronounced for CB levels above the percolation threshold.},
  language  = {en}
}
@article{HarishWriggersJungketal.2016,
  author    = {Harish, Ajay B. and Wriggers, Peter and Jungk, Juliane and Hojdis, Nils and Recker, Carla},
  title     = {Mesoscale Constitutive Modeling of Non-Crystallizing Filled Elastomers},
  series = {Computational Mechanics},
  volume    = {57},
  journal   = {Computational Mechanics},
  publisher = {Springer},
  address   = {Berlin},
  issn      = {1432-0924},
  doi       = {10.1007/s00466-015-1251-1},
  pages     = {653 -- 677},
  year      = {2016},
  abstract  = {Elastomers are exceptional materials owing to their ability to undergo large deformations before failure. However, due to their very low stiffness, they are not always suitable for industrial applications. Addition of filler particles provides reinforcing effects and thus enhances the material properties that render them more versatile for applications like tyres etc. However, deformation behavior of filled polymers is accompanied by several nonlinear effects like Mullins and Payne effect. To this day, the physical and chemical changes resulting in such nonlinear effect remain an active area of research. In this work, we develop a heterogeneous (or multiphase) constitutive model at the mesoscale explicitly considering filler particle aggregates, elastomeric matrix and their mechanical interaction through an approximate interface layer. The developed constitutive model is used to demonstrate cluster breakage, also, as one of the possible sources for Mullins effect observed in non-crystallizing filled elastomers.},
  language  = {en}
}
@article{HentschkeHagerHojdis2014,
  author    = {Hentschke, Reinhard and Hager, Jonathan and Hojdis, Nils},
  title     = {Molecular Modeling Approach to the Prediction of Mechanical Properties of Silica-Reinforced Rubbers},
  series = {Journal of Applied Polymer Science},
  volume    = {131},
  journal   = {Journal of Applied Polymer Science},
  number    = {18},
  publisher = {Wiley},
  address   = {New York, NY},
  issn      = {1097-4628},
  doi       = {10.1002/app.40806},
  pages     = {1 -- 9},
  year      = {2014},
  abstract  = {Recently, we have suggested a nanomechanical model for dissipative loss in filled elastomer networks in the context of the Payne effect. The mechanism is based on a total interfiller particle force exhibiting an intermittent loop, due to the combination of short-range repulsion and dispersion forces with a long-range elastic attraction. The sum of these forces leads, under external strain, to a spontaneous instability of "bonds" between the aggregates in a filler network and attendant energy dissipation. Here, we use molecular dynamics simulations to obtain chemically realistic forces between surface modified silica particles. The latter are combined with the above model to estimate the loss modulus and the low strain storage modulus in elastomers containing the aforementioned filler-compatibilizer systems. The model is compared to experimental dynamic moduli of silica filled rubbers. We find good agreement between the model predictions and the experiments as function of the compatibilizer's molecular structure and its bulk concentration.},
  language  = {en}
}
@article{KuhnhenneRegerPyschnyetal.2020,
  author    = {Kuhnhenne, Markus and Reger, Vitali and Pyschny, Dominik and D{\"o}ring, Bernd},
  title     = {Influence of airtightness of steel sandwich panel joints on heat losses},
  series = {E3S Web of Conferences 12th Nordic Symposium on Building Physics (NSB 2020)},
  volume    = {172},
  journal   = {E3S Web of Conferences 12th Nordic Symposium on Building Physics (NSB 2020)},
  number    = {Art. 05008},
  publisher = {EDP Sciences},
  address   = {Les Ulis},
  doi       = {10.1051/e3sconf/202017205008},
  pages     = {6},
  year      = {2020},
  abstract  = {Energy saving ordinances requires that buildings must be designed in such a way that the heat transfer surface including the joints is permanently air impermeable. The prefabricated roof and wall panels in lightweight steel constructions are airtight in the area of the steel covering layers. The sealing of the panel joints contributes to fulfil the comprehensive requirements for an airtight building envelope. To improve the airtightness of steel sandwich panels, additional sealing tapes can be installed in the panel joint. The influence of these sealing tapes was evaluated by measurements carried out by the RWTH Aachen University - Sustainable Metal Building Envelopes. Different installation situations were evaluated by carrying out airtightness tests for different joint distances. In addition, the influence on the heat transfer coefficient was also evaluated using the Finite Element Method (FEM). The combination of obtained air volume flow and transmission losses enables to create an "effective heat transfer coefficient" due to transmission and infiltration. This summarizes both effects in one value and is particularly helpful for approximate calculations on energy efficiency.},
  language  = {en}
}
@article{KunkelGebhardtMpofuetal.2019,
  author    = {Kunkel, Maximilian Hugo and Gebhardt, Andreas and Mpofu, Khumbulani and Kallweit, Stephan},
  title     = {Quality assurance in metal powder bed fusion via deep-learning-based image classification},
  series = {Rapid Prototyping Journal},
  volume    = {26},
  journal   = {Rapid Prototyping Journal},
  number    = {2},
  issn      = {1355-2546},
  doi       = {10.1108/RPJ-03-2019-0066},
  pages     = {259 -- 266},
  year      = {2019},
  language  = {en}
}
@article{MaurischatPerkins2020,
  author    = {Maurischat, Andreas and Perkins, Rudolph},
  title     = {Taylor coefficients of Anderson generating functions and Drinfeld torsion extensions},
  number    = {Vol. 18, No. 01},
  publisher = {World Scientific},
  address   = {Singapur},
  doi       = {10.1142/S1793042122500099},
  pages     = {113 -- 130},
  year      = {2020},
  abstract  = {We generalize our work on Carlitz prime power torsion extension to torsion extensions of Drinfeld modules of arbitrary rank. As in the Carlitz case, we give a description of these extensions in terms of evaluations of Anderson generating functions and their hyperderivatives at roots of unity. We also give a direct proof that the image of the Galois representation attached to the p-adic Tate module lies in the p-adic points of the motivic Galois group. This is a generalization of the corresponding result of Chang and Papanikolas for the t-adic case.},
  language  = {en}
}
@article{ElMoussaouiTalbiAtmaneetal.2020,
  author    = {El Moussaoui, Noureddine and Talbi, Sofian and Atmane, Ilyas and Kassmi, Khalil and Schwarzer, Klemens and Chayeb, Hamid and Bachiri, Najib},
  title     = {Feasibility of a new design of a Parabolic Trough Solar Thermal Cooker (PSTC)},
  series = {Solar Energy},
  volume    = {201},
  journal   = {Solar Energy},
  number    = {Vol. 201 (May 2020)},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {0038-092X},
  doi       = {10.1016/j.solener.2020.03.079},
  pages     = {866 -- 871},
  year      = {2020},
  abstract  = {In this article, we describe the structure, the functioning, and the tests of parabolic trough solar thermal cooker (PSTC). This oven is designed to meet the needs of rural residents, including Urban, which requires stable cooking temperatures above 200 °C. The cooking by this cooker is based on the concentration of the sun's rays on a glass vacuum tube and heating of the oil circulate in a big tube, located inside the glass tube. Through two small tubes, associated with large tube, the heated oil, rise and heats the pot of cooking pot containing the food to be cooked (capacity of 5 kg). This cooker is designed in Germany and extensively tested in Morocco for use by the inhabitants who use wood from forests. During a sunny day, having a maximum solar radiation around 720 W/m2 and temperature ambient around 26 °C, maximum temperatures recorded of the small tube, the large tube and the center of the pot are respectively: 370 °C, 270 °C and 260 °C. The cooking process with food at high (fries, ..), we show that the cooking oil temperature rises to 200 °C, after 1 h of heating, the cooking is done at a temperature of 120 °C for 20 min. These temperatures are practically stable following variations and decreases in the intensity of irradiance during the day. The comparison of these results with those of the literature shows an improvement of 30-50 \% on the maximum value of the temperature with a heat storage that could reach 60 min of autonomy. All the results obtained show the good functioning of the PSTC and the feasibility of cooking food at high temperature (>200 °C).},
  language  = {en}
}
@article{MuellerJungAhammer2017,
  author    = {M{\"u}ller, Wolfram and Jung, Alexander and Ahammer, Helmut},
  title     = {Advantages and problems of nonlinear methods applied to analyze physiological time signals: human balance control as an example},
  series = {Scientific Reports},
  volume    = {7},
  journal   = {Scientific Reports},
  number    = {Article number 2464},
  publisher = {Springer Nature},
  address   = {Cham},
  isbn      = {2045-2322},
  doi       = {10.1038/s41598-017-02665-5},
  pages     = {1 -- 11},
  year      = {2017},
  language  = {en}
}
@article{OrzadaFiedlerBitzetal.2020,
  author    = {Orzada, Stephan and Fiedler, Thomas M. and Bitz, Andreas and Ladd, Mark E. and Quick, Harald H.},
  title     = {Local SAR compression with overestimation control to reduce maximum relative SAR overestimation and improve multi-channel RF array performance},
  series = {Magnetic Resonance Materials in Physics, Biology and Medicine},
  journal   = {Magnetic Resonance Materials in Physics, Biology and Medicine},
  number    = {34 (2021)},
  publisher = {Springer},
  address   = {Heidelberg},
  isbn      = {1352-8661},
  doi       = {10.1007/s10334-020-00890-0},
  pages     = {153 -- 164},
  year      = {2020},
  abstract  = {Objective In local SAR compression algorithms, the overestimation is generally not linearly dependent on actual local SAR. This can lead to large relative overestimation at low actual SAR values, unnecessarily constraining transmit array performance. Method Two strategies are proposed to reduce maximum relative overestimation for a given number of VOPs. The first strategy uses an overestimation matrix that roughly approximates actual local SAR; the second strategy uses a small set of pre-calculated VOPs as the overestimation term for the compression. Result Comparison with a previous method shows that for a given maximum relative overestimation the number of VOPs can be reduced by around 20\% at the cost of a higher absolute overestimation at high actual local SAR values. Conclusion The proposed strategies outperform a previously published strategy and can improve the SAR compression where maximum relative overestimation constrains the performance of parallel transmission.},
  language  = {en}
}
@article{UlmerBraunChengetal.2020,
  author    = {Ulmer, Jessica and Braun, Sebastian and Cheng, Chi-Tsun and Dowey, Steve and Wollert, J{\"o}rg},
  title     = {Human-Centered Gamification Framework for Manufacturing Systems},
  series = {Procedia CIRP},
  volume    = {93},
  journal   = {Procedia CIRP},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {2212-8271},
  doi       = {10.1016/j.procir.2020.04.076},
  pages     = {670 -- 675},
  year      = {2020},
  abstract  = {While bringing new opportunities, the Industry 4.0 movement also imposes new challenges to the manufacturing industry and all its stakeholders. In this competitive environment, a skilled and engaged workforce is a key to success. Gamification can generate valuable feedbacks for improving employees' engagement and performance. Currently, Gamification in workspaces focuses on computer-based assignments and training, while tasks that require manual labor are rarely considered. This research provides an overview of Enterprise Gamification approaches and evaluates the challenges. Based on that, a skill-based Gamification framework for manual tasks is proposed, and a case study in the Industry 4.0 model factory is shown.},
  language  = {en}
}
@article{EveraersKarimiVarzanehFlecketal.2020,
  author    = {Everaers, Ralf and Karimi-Varzaneh, Hossein Ali and Fleck, Franz and Hojdis, Nils and Svaneborg, Carsten},
  title     = {Kremer-Grest Models for Commodity Polymer Melts: Linking Theory, Experiment, and Simulation at the Kuhn Scale},
  series = {Macromolecules},
  volume    = {53},
  journal   = {Macromolecules},
  number    = {6},
  publisher = {ACS Publications},
  address   = {Washington, DC},
  issn      = {1520-5835},
  doi       = {10.1021/acs.macromol.9b02428},
  pages     = {1901 -- 1916},
  year      = {2020},
  abstract  = {The Kremer-Grest (KG) polymer model is a standard model for studying generic polymer properties in molecular dynamics simulations. It owes its popularity to its simplicity and computational efficiency, rather than its ability to represent specific polymers species and conditions. Here we show that by tuning the chain stiffness it is possible to adapt the KG model to model melts of real polymers. In particular, we provide mapping relations from KG to SI units for a wide range of commodity polymers. The connection between the experimental and the KG melts is made at the Kuhn scale, i.e., at the crossover from the chemistry-specific small scale to the universal large scale behavior. We expect Kuhn scale-mapped KG models to faithfully represent universal properties dominated by the large scale conformational statistics and dynamics of flexible polymers. In particular, we observe very good agreement between entanglement moduli of our KG models and the experimental moduli of the target polymers.},
  language  = {en}
}
@article{MeyerHentschkeHageretal.2017,
  author    = {Meyer, Jan and Hentschke, Reinhard and Hager, Jonathan and Hojdis, Nils and Karimi-Varzaneh, Hossein Ali},
  title     = {Molecular Simulation of Viscous Dissipation due to Cyclic Deformation of a Silica-Silica Contact in Filled Rubber},
  series = {Macromolecules},
  volume    = {50},
  journal   = {Macromolecules},
  number    = {17},
  issn      = {1520-5835},
  doi       = {10.1021/acs.macromol.7b00947},
  pages     = {6679 -- 6689},
  year      = {2017},
  language  = {en}
}
@article{HagerHentschkeHojdisetal.2015,
  author    = {Hager, Jonathan and Hentschke, Reinhard and Hojdis, Nils and Karimi-Varzaneh, Hossein Ali},
  title     = {Computer Simulation of Particle-Particle Interaction in a Model Polymer Nanocomposite},
  series = {Macromolecules},
  volume    = {48},
  journal   = {Macromolecules},
  number    = {24},
  issn      = {1520-5835},
  doi       = {10.1021/acs.macromol.5b01864},
  pages     = {9039 -- 9049},
  year      = {2015},
  language  = {en}
}
@article{WallerBraunHojdisetal.2007,
  author    = {Waller, Mark P. and Braun, Heiko and Hojdis, Nils and B{\"u}hl, Michael},
  title     = {Geometries of Second-Row Transition-Metal Complexes from Density-Functional Theory},
  series = {Journal of Chemical Theory and Computation},
  volume    = {3},
  journal   = {Journal of Chemical Theory and Computation},
  number    = {6},
  issn      = {1549-9626},
  doi       = {10.1021/ct700178y},
  pages     = {2234 -- 2242},
  year      = {2007},
  language  = {en}
}
@article{SvaneborgKarimiVarzanehHojdisetal.2018,
  author    = {Svaneborg, Carsten and Karimi-Varzaneh, Hossein Ali and Hojdis, Nils and Fleck, Franz and Everaers, Ralf},
  title     = {Kremer-Grest Models for Universal Properties of Specific Common Polymer Species},
  series = {Soft Condensed Matter},
  journal   = {Soft Condensed Matter},
  number    = {1606.05008},
  year      = {2018},
  abstract  = {The Kremer-Grest (KG) bead-spring model is a near standard in Molecular Dynamic simulations of generic polymer properties. It owes its popularity to its computational efficiency, rather than its ability to represent specific polymer species and conditions. Here we investigate how to adapt the model to match the universal properties of a wide range of chemical polymers species. For this purpose we vary a single parameter originally introduced by Faller and M{\"u}ller-Plathe, the chain stiffness. Examples include polystyrene, polyethylene, polypropylene, cis-polyisoprene, polydimethylsiloxane, polyethyleneoxide and styrene-butadiene rubber. We do this by matching the number of Kuhn segments per chain and the number of Kuhn segments per cubic Kuhn volume for the polymer species and for the Kremer-Grest model. We also derive mapping relations for converting KG model units back to physical units, in particular we obtain the entanglement time for the KG model as function of stiffness allowing for a time mapping. To test these relations, we generate large equilibrated well entangled polymer melts, and measure the entanglement moduli using a static primitive-path analysis of the entangled melt structure as well as by simulations of step-strain deformation of the model melts. The obtained moduli for our model polymer melts are in good agreement with the experimentally expected moduli.},
  language  = {en}
}
@article{MayerHentschkeHageretal.2017,
  author    = {Mayer, Jan and Hentschke, Reinhard and Hager, Jonathan and Hojdis, Nils and Karimi-Varnaneh, Hossein Ali},
  title     = {A Nano-Mechanical Instability as Primary Contribution to Rolling Resistance},
  series = {Scientific Reports},
  volume    = {7},
  journal   = {Scientific Reports},
  number    = {Article number 11275},
  publisher = {Springer},
  address   = {Berlin},
  issn      = {2045-2322},
  year      = {2017},
  language  = {en}
}
@article{UlmerBraunChengetal.2022,
  author    = {Ulmer, Jessica and Braun, Sebastian and Cheng, Chi-Tsun and Dowey, Steve and Wollert, J{\"o}rg},
  title     = {Gamification of virtual reality assembly training: Effects of a combined point and level system on motivation and training results},
  series = {International Journal of Human-Computer Studies},
  volume    = {165},
  journal   = {International Journal of Human-Computer Studies},
  number    = {Art. No. 102854},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {1071-5819},
  doi       = {10.1016/j.ijhcs.2022.102854},
  year      = {2022},
  abstract  = {Virtual Reality (VR) offers novel possibilities for remote training regardless of the availability of the actual equipment, the presence of specialists, and the training locations. Research shows that training environments that adapt to users' preferences and performance can promote more effective learning. However, the observed results can hardly be traced back to specific adaptive measures but the whole new training approach. This study analyzes the effects of a combined point and leveling VR-based gamification system on assembly training targeting specific training outcomes and users' motivations. The Gamified-VR-Group with 26 subjects received the gamified training, and the Non-Gamified-VR-Group with 27 subjects received the alternative without gamified elements. Both groups conducted their VR training at least three times before assembling the actual structure. The study found that a level system that gradually increases the difficulty and error probability in VR can significantly lower real-world error rates, self-corrections, and support usages. According to our study, a high error occurrence at the highest training level reduced the Gamified-VR-Group's feeling of competence compared to the Non-Gamified-VR-Group, but at the same time also led to lower error probabilities in real-life. It is concluded that a level system with a variable task difficulty should be combined with carefully balanced positive and negative feedback messages. This way, better learning results, and an improved self-evaluation can be achieved while not causing significant impacts on the participants' feeling of competence.},
  language  = {en}
}
@article{PfaffEnningSutter2022,
  author    = {Pfaff, Raphael and Enning, Manfred and Sutter, Stefan},
  title     = {A risk‑based approach to automatic brake tests for rail freight service: incident analysis and realisation concept},
  series = {SN Applied Sciences},
  volume    = {4},
  journal   = {SN Applied Sciences},
  number    = {4},
  publisher = {Springer},
  address   = {Cham},
  issn      = {2523-3971},
  doi       = {10.1007/s42452-022-05007-x},
  pages     = {1 -- 14},
  year      = {2022},
  abstract  = {This study reviews the practice of brake tests in freight railways, which is time consuming and not suitable to detect certain failure types. Public incident reports are analysed to derive a reasonable brake test hardware and communication architecture, which aims to provide automatic brake tests at lower cost than current solutions. The proposed solutions relies exclusively on brake pipe and brake cylinder pressure sensors, a brake release position switch as well as radio communication via standard protocols. The approach is embedded in the Wagon 4.0 concept, which is a holistic approach to a smart freight wagon. The reduction of manual processes yields a strong incentive due to high savings in manual labour and increased productivity.},
  language  = {en}
}
@article{OliveiraMolinnusBegingetal.2021,
  author    = {Oliveira, Danilo A. and Molinnus, Denise and Beging, Stefan and Siqueira Jr, Jos{\´e} R. and Sch{\"o}ning, Michael Josef},
  title     = {Biosensor Based on Self-Assembled Films of Graphene Oxide and Polyaniline Using a Field-Effect Device Platform},
  series = {physica status solidi (a) applications and materials science},
  volume    = {218},
  journal   = {physica status solidi (a) applications and materials science},
  number    = {13},
  publisher = {Wiley-VCH},
  address   = {Weinheim},
  issn      = {1862-6319},
  doi       = {10.1002/pssa.202000747},
  pages     = {1 -- 9},
  year      = {2021},
  abstract  = {A new functionalization method to modify capacitive electrolyte-insulator-semiconductor (EIS) structures with nanofilms is presented. Layers of polyallylamine hydrochloride (PAH) and graphene oxide (GO) with the compound polyaniline:poly(2-acrylamido-2-methyl-1-propanesulfonic acid) (PANI:PAAMPSA) are deposited onto a p-Si/SiO2 chip using the layer-by-layer technique (LbL). Two different enzymes (urease and penicillinase) are separately immobilized on top of a five-bilayer stack of the PAH:GO/PANI:PAAMPSA-modified EIS chip, forming a biosensor for detection of urea and penicillin, respectively. Electrochemical characterization is performed by constant capacitance (ConCap) measurements, and the film morphology is characterized by atomic force microscopy (AFM) and scanning electron microscopy (SEM). An increase in the average sensitivity of the modified biosensors (EIS-nanofilm-enzyme) of around 15\% is found in relation to sensors, only carrying the enzyme but without the nanofilm (EIS-enzyme). In this sense, the nanofilm acts as a stable bioreceptor onto the EIS chip improving the output signal in terms of sensitivity and stability.},
  language  = {en}
}
@article{WeldenNagamineKomesuWagneretal.2021,
  author    = {Welden, Rene and Nagamine Komesu, Cindy A. and Wagner, Patrick H. and Sch{\"o}ning, Michael Josef and Wagner, Torsten},
  title     = {Photoelectrochemical enzymatic penicillin biosensor: A proof-of-concept experiment},
  series = {Electrochemical Science Advances},
  volume    = {2},
  journal   = {Electrochemical Science Advances},
  number    = {4},
  publisher = {Wiley-VCH},
  address   = {Weinheim},
  issn      = {2698-5977},
  doi       = {10.1002/elsa.202100131},
  pages     = {1 -- 5},
  year      = {2021},
  abstract  = {Photoelectrochemical (PEC) biosensors are a rather novel type of biosensors thatutilizelighttoprovideinformationaboutthecompositionofananalyte,enablinglight-controlled multi-analyte measurements. For enzymatic PEC biosensors,amperometric detection principles are already known in the literature. In con-trast, there is only a little information on H+-ion sensitive PEC biosensors. Inthis work, we demonstrate the detection of H+ions emerged by H+-generatingenzymes, exemplarily demonstrated with penicillinase as a model enzyme on atitanium dioxide photoanode. First, we describe the pH sensitivity of the sensorand study possible photoelectrocatalytic reactions with penicillin. Second, weshow the enzymatic PEC detection of penicillin.},
  language  = {en}
}
@article{RichterBraunsteinStaeudleetal.2021,
  author    = {Richter, Charlotte and Braunstein, Bjoern and Staeudle, Benjamin and Attias, Julia and Suess, Alexander and Weber, Tobias and Mileva, Katya N. and Rittweger, Joern and Green, David A. and Albracht, Kirsten},
  title     = {Contractile behavior of the gastrocnemius medialis muscle during running in simulated hypogravity},
  series = {npj Microgravity},
  volume    = {7},
  journal   = {npj Microgravity},
  number    = {Article number: 32},
  publisher = {Springer Nature},
  address   = {New York},
  issn      = {2373-8065},
  doi       = {10.1038/s41526-021-00155-7},
  pages     = {7 Seiten},
  year      = {2021},
  abstract  = {Vigorous exercise countermeasures in microgravity can largely attenuate muscular degeneration, albeit the extent of applied loading is key for the extent of muscle wasting. Running on the International Space Station is usually performed with maximum loads of 70\% body weight (0.7 g). However, it has not been investigated how the reduced musculoskeletal loading affects muscle and series elastic element dynamics, and thereby force and power generation. Therefore, this study examined the effects of running on the vertical treadmill facility, a ground-based analog, at simulated 0.7 g on gastrocnemius medialis contractile behavior. The results reveal that fascicle-series elastic element behavior differs between simulated hypogravity and 1 g running. Whilst shorter peak series elastic element lengths at simulated 0.7 g appear to be the result of lower muscular and gravitational forces acting on it, increased fascicle lengths and decreased velocities could not be anticipated, but may inform the development of optimized running training in hypogravity. However, whether the alterations in contractile behavior precipitate musculoskeletal degeneration warrants further study.},
  language  = {en}
}
@article{Olbertz2019,
  author    = {Olbertz, Klaus},
  title     = {Arbeitsrechtliche Akzente der Gesetzgebung und Rechtsprechung in 2018 : Ein kurzweiliger R{\"u}ckblick auf das Arbeitsrecht des vergangenen Jahres},
  series = {NWB - Steuer- und Wirtschaftsrecht},
  journal   = {NWB - Steuer- und Wirtschaftsrecht},
  number    = {5},
  issn      = {0028-3460},
  pages     = {266 -- 279},
  year      = {2019},
  language  = {de}
}
@article{Olbertz2019,
  author    = {Olbertz, Klaus},
  title     = {Auslandsentsendungen im arbeitsrechtlichen Zusammenhang : Ausgestaltung eines Entsendungsvertrags und mitbestimmungsrechtliche Aspekte},
  series = {NWB - Steuer- und Wirtschaftsrecht},
  journal   = {NWB - Steuer- und Wirtschaftsrecht},
  number    = {19},
  issn      = {0028-3460},
  pages     = {1400 -- 1406},
  year      = {2019},
  language  = {de}
}
@article{Olbertz2019,
  author    = {Olbertz, Klaus},
  title     = {Rechtssichere Vereinbarungen von K{\"u}ndigungsfristen im Arbeitsvertrag : Weitestgehende Abdingbarkeit gesetzlicher Vorgaben erm{\"o}glicht passgenaue Gestaltungen},
  series = {NWB - Steuer- und Wirtschaftsrecht},
  journal   = {NWB - Steuer- und Wirtschaftsrecht},
  number    = {23},
  issn      = {0028-3460},
  pages     = {1693 -- 1699},
  year      = {2019},
  language  = {de}
}
@article{Olbertz2019,
  author    = {Olbertz, Klaus},
  title     = {Die Optionen des Arbeitgebers nach Krankmeldung des Arbeitnehmers : Ein {\"U}berblick {\"u}ber die Rechte und Pflichten des Arbeitgebers bei Arbeitsunf{\"a}higkeit des Mitarbeiters},
  series = {NWB - Steuer- und Wirtschaftsrecht},
  journal   = {NWB - Steuer- und Wirtschaftsrecht},
  number    = {30},
  issn      = {0028-3460},
  pages     = {2222 -- 2229},
  year      = {2019},
  language  = {de}
}
@article{Olbertz2019,
  author    = {Olbertz, Klaus},
  title     = {Die arbeitsvertragliche Vereinbarung von Vertragsstrafen : Anforderungen an wirksame Vertragsstrafenabreden in Formulararbeitsvertr{\"a}gen beachten},
  series = {NWB - Steuer- und Wirtschaftsrecht},
  journal   = {NWB - Steuer- und Wirtschaftsrecht},
  number    = {45},
  issn      = {0028-3460},
  pages     = {3302 -- 3308},
  year      = {2019},
  language  = {de}
}
@article{Olbertz2020,
  author    = {Olbertz, Klaus},
  title     = {Jahresr{\"u}ckblick Arbeitsrecht 2019 : Gesetzes{\"a}nderungen und insbesondere im Zeichen des Befristungs- und Urlaubsrechts stehende h{\"o}chstrichterliche Rechtsprechung},
  series = {NWB - Steuer- und Wirtschaftsrecht},
  journal   = {NWB - Steuer- und Wirtschaftsrecht},
  number    = {8},
  publisher = {NWB-Verl.},
  address   = {Herne},
  issn      = {0028-3460},
  pages     = {557 -- 569},
  year      = {2020},
  abstract  = {In Fortschreibung des Jahresr{\"u}ckblicks 2018 (Olbertz, NWB 5/2019 S. 266 ) skizziert der vorliegende Beitrag die j{\"u}ngsten nennenswerten Entwicklungen im Arbeitsrecht des Jahres 2019. Im Bereich der Gesetzgebung, mit dem sich der erste Teil des Beitrags befasst, betrifft dies etwa das Fachkr{\"a}fteeinwanderungsgesetz, die angestoßenen Schutzvorschriften f{\"u}r Whistleblower oder das gesetzlich verankerte Recht auf Br{\"u}ckenteilzeit. In der arbeitsrechtlichen h{\"o}chstrichterlichen Rechtsprechung stand das Jahr 2019 insbesondere im Zeichen des Befristungs- und des Urlaubsrechts. Was hier und dar{\"u}ber hinaus wegweisend war, zeigt der zweite Teil des Beitrags.},
  language  = {de}
}
@article{Olbertz2020,
  author    = {Olbertz, Klaus},
  title     = {GmbH-Gesch{\"a}ftsf{\"u}hrer: das eine Mal Arbeitnehmer, das andere Mal nicht : Arbeits- und sozialrechtliche Anwendung von Schutzvorschriften auf den Gesch{\"a}ftsf{\"u}hrer von A bis Z},
  series = {NWB - Steuer- und Wirtschaftsrecht},
  journal   = {NWB - Steuer- und Wirtschaftsrecht},
  number    = {19},
  publisher = {NWB-Verl.},
  address   = {Herne},
  issn      = {0028-3460},
  pages     = {1431 -- 1441},
  year      = {2020},
  language  = {de}
}
@article{Olbertz2020,
  author    = {Olbertz, Klaus},
  title     = {Wenn der „leitende" Angestellte doch nur ein „normaler" Arbeitnehmer ist ... : Zur Rechtsstellung leitender Angestellter, zu Fehleinsch{\"a}tzungen des Arbeitgebers und Praxishinweisen},
  series = {NWB - Steuer- und Wirtschaftsrecht},
  journal   = {NWB - Steuer- und Wirtschaftsrecht},
  number    = {32},
  publisher = {NWB-Verl.},
  address   = {Herne},
  issn      = {0028-3460},
  pages     = {2397 -- 2406},
  year      = {2020},
  language  = {de}
}
@article{Olbertz2021,
  author    = {Olbertz, Klaus},
  title     = {Die Dienstreisezeit als Arbeitszeit - oder doch nicht? : Zur arbeitgeberfreundlichen Bewertung von Dienstreisezeiten durch das Bundesarbeitsgericht},
  series = {NWB - Steuer- und Wirtschaftsrecht},
  journal   = {NWB - Steuer- und Wirtschaftsrecht},
  number    = {1},
  issn      = {0028-3460},
  pages     = {38 -- 44},
  year      = {2021},
  abstract  = {Der arbeitsrechtlich richtige Umgang mit Zeiten einer Dienstreise kann in der betrieblichen Praxis Probleme bereiten. Ob die Reisezeiten als solche Arbeitszeit i. S. des Arbeitszeitgesetzes (ArbZG ) darstellen, also bspw. auf die t{\"a}gliche H{\"o}chstarbeitszeit angerechnet werden m{\"u}ssen oder nicht, ist oftmals genauso unklar wie die Frage, ob und inwieweit Reisezeiten verg{\"u}tungspflichtig sind. Aber auch, ob ein Arbeitnehmer {\"u}berhaupt zur Durchf{\"u}hrung einer Dienstreise verpflichtet werden kann, ist ein m{\"o}glicher Anlass von Streitigkeiten zwischen den Arbeitsvertragsparteien, wie verschiedene Gerichtsentscheidungen zeigen. Der nachfolgende Beitrag beantwortet die aufgeworfenen Fragen und gibt hierzu einen praxisorientierten {\"U}berblick.},
  language  = {de}
}
@article{HeinkeKnickerAlbracht2021,
  author    = {Heinke, Lars N. and Knicker, Axel J. and Albracht, Kirsten},
  title     = {Test-retest reliability of the internal shoulder rotator muscles' stretch reflex in healthy men},
  series = {Journal of Electromyography and Kinesiology},
  volume    = {62},
  journal   = {Journal of Electromyography and Kinesiology},
  number    = {Article 102611},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {1050-6411},
  doi       = {10.1016/j.jelekin.2021.102611},
  year      = {2021},
  abstract  = {Until now the reproducibility of the short latency stretch reflex of the internal rotator muscles of the glenohumeral joint has not been identified. Twenty-three healthy male participants performed three sets of external shoulder rotation stretches with various pre-activation levels on two different dates of measurement to assess test-retest reliability. All stretches were applied with a dynamometer acceleration of 104°/s2 and a velocity of 150°/s. Electromyographical response was measured via surface EMG. Reflex latencies showed a pre-activation effect (ƞ2 = 0,355). ICC ranged from 0,735 to 0,909 indicating an overall "good" relative reliability. SRD 95\% lay between ±7,0 to ±12,3 ms.. The reflex gain showed overall poor test-retest reproducibility. The chosen methodological approach presented a suitable test protocol for shoulder muscles stretch reflex latency evaluation. A proof-of-concept study to validate the presented methodical approach in shoulder involvement including subjects with clinically relevant conditions is recommended.},
  language  = {en}
}
@article{HeelDiktaBraekers2021,
  author    = {Heel, Mareike van and Dikta, Gerhard and Braekers, Roel},
  title     = {Bootstrap based goodness‑of‑fit tests for binary multivariate regression models},
  series = {Journal of the Korean Statistical Society},
  volume    = {51},
  journal   = {Journal of the Korean Statistical Society},
  publisher = {Springer Nature},
  address   = {Singapur},
  issn      = {2005-2863 (Online)},
  doi       = {10.1007/s42952-021-00142-4},
  pages     = {28 Seiten},
  year      = {2021},
  abstract  = {We consider a binary multivariate regression model where the conditional expectation of a binary variable given a higher-dimensional input variable belongs to a parametric family. Based on this, we introduce a model-based bootstrap (MBB) for higher-dimensional input variables. This test can be used to check whether a sequence of independent and identically distributed observations belongs to such a parametric family. The approach is based on the empirical residual process introduced by Stute (Ann Statist 25:613-641, 1997). In contrast to Stute and Zhu's approach (2002) Stute \& Zhu (Scandinavian J Statist 29:535-545, 2002), a transformation is not required. Thus, any problems associated with non-parametric regression estimation are avoided. As a result, the MBB method is much easier for users to implement. To illustrate the power of the MBB based tests, a small simulation study is performed. Compared to the approach of Stute \& Zhu (Scandinavian J Statist 29:535-545, 2002), the simulations indicate a slightly improved power of the MBB based method. Finally, both methods are applied to a real data set.},
  language  = {en}
}
@article{KlettkeHomburgGell2015,
  author    = {Klettke, Tanja and Homburg, Carsten and Gell, Sebastian},
  title     = {How to measure analyst forecast effort},
  series = {European Accounting Review},
  volume    = {24},
  journal   = {European Accounting Review},
  number    = {1},
  publisher = {Taylor \& Francis},
  address   = {London},
  issn      = {0963-8180},
  doi       = {10.1080/09638180.2014.909291},
  pages     = {129 -- 146},
  year      = {2015},
  abstract  = {We introduce a new way to measure the forecast effort that analysts devote to their earnings forecasts by measuring the analyst's general effort for all covered firms. While the commonly applied effort measure is based on analyst behaviour for one firm, our measure considers analyst behaviour for all covered firms. Our general effort measure captures additional information about analyst effort and thus can identify accurate forecasts. We emphasise the importance of investigating analyst behaviour in a larger context and argue that analysts who generally devote substantial forecast effort are also likely to devote substantial effort to a specific firm, even if this effort might not be captured by a firm-specific measure. Empirical results reveal that analysts who devote higher general forecast effort issue more accurate forecasts. Additional investigations show that analysts' career prospects improve with higher general forecast effort. Our measure improves on existing methods as it has higher explanatory power regarding differences in forecast accuracy than the commonly applied effort measure. Additionally, it can address research questions that cannot be examined with a firm-specific measure. It provides a simple but comprehensive way to identify accurate analysts.},
  language  = {en}
}
@article{Timme2021,
  author    = {Timme, Michael},
  title     = {Rechtsprechungs{\"u}bersicht zum Wohnraummietrecht},
  series = {Monatsschrift f{\"u}r Deutsches Recht},
  volume    = {75},
  journal   = {Monatsschrift f{\"u}r Deutsches Recht},
  number    = {1},
  publisher = {Verlag Dr. Otto Schmidt},
  address   = {K{\"o}ln},
  issn      = {2194-4202},
  doi       = {10.9785/mdtr-2021-750113},
  pages     = {6 -- 11},
  year      = {2021},
  language  = {de}
}
@article{MuellerLeiseLorenzetal.2020,
  author    = {M{\"u}ller, Tim M. and Leise, Philipp and Lorenz, Imke-Sophie and Altherr, Lena and Pelz, Peter F.},
  title     = {Optimization and validation of pumping system design and operation for water supply in high-rise buildings},
  series = {Optimization and Engineering},
  volume    = {2021},
  journal   = {Optimization and Engineering},
  number    = {22},
  publisher = {Springer},
  issn      = {1573-2924},
  doi       = {10.1007/s11081-020-09553-4},
  pages     = {643 -- 686},
  year      = {2020},
  abstract  = {The application of mathematical optimization methods for water supply system design and operation provides the capacity to increase the energy efficiency and to lower the investment costs considerably. We present a system approach for the optimal design and operation of pumping systems in real-world high-rise buildings that is based on the usage of mixed-integer nonlinear and mixed-integer linear modeling approaches. In addition, we consider different booster station topologies, i.e. parallel and series-parallel central booster stations as well as decentral booster stations. To confirm the validity of the underlying optimization models with real-world system behavior, we additionally present validation results based on experiments conducted on a modularly constructed pumping test rig. Within the models we consider layout and control decisions for different load scenarios, leading to a Deterministic Equivalent of a two-stage stochastic optimization program. We use a piecewise linearization as well as a piecewise relaxation of the pumps' characteristics to derive mixed-integer linear models. Besides the solution with off-the-shelf solvers, we present a problem specific exact solving algorithm to improve the computation time. Focusing on the efficient exploration of the solution space, we divide the problem into smaller subproblems, which partly can be cut off in the solution process. Furthermore, we discuss the performance and applicability of the solution approaches for real buildings and analyze the technical aspects of the solutions from an engineer's point of view, keeping in mind the economically important trade-off between investment and operation costs.},
  language  = {en}
}
@article{AltherrLeisePfetschetal.2018,
  author    = {Altherr, Lena and Leise, Philipp and Pfetsch, Marc E. and Schmitt, Andreas},
  title     = {Algorithmic design and resilience assessment of energy efficient high-rise water supply systems},
  series = {Applied Mechanics and Materials},
  volume    = {885},
  journal   = {Applied Mechanics and Materials},
  publisher = {Trans Tech Publications},
  address   = {B{\"a}ch},
  issn      = {1662-7482},
  doi       = {10.4028/www.scientific.net/AMM.885.211},
  pages     = {211 -- 223},
  year      = {2018},
  abstract  = {High-rise water supply systems provide water flow and suitable pressure in all levels of tall buildings. To design such state-of-the-art systems, the consideration of energy efficiency and the anticipation of component failures are mandatory. In this paper, we use Mixed-Integer Nonlinear Programming to compute an optimal placement of pipes and pumps, as well as an optimal control strategy.Moreover, we consider the resilience of the system to pump failures. A resilient system is able to fulfill a predefined minimum functionality even though components fail or are restricted in their normal usage. We present models to measure and optimize the resilience. To demonstrate our approach, we design and analyze an optimal resilient decentralized water supply system inspired by a real-life hotel building.},
  language  = {en}
}
@article{ZabirovSchleserBucherer2021,
  author    = {Zabirov, Alexander and Schleser, Markus and Bucherer, Sebastian},
  title     = {F{\"u}ge- und Dichtkonzept f{\"u}r einen Leichtbauverbrennungsmotor},
  series = {adh{\"a}sion KLEBEN \& DICHTEN},
  volume    = {65},
  journal   = {adh{\"a}sion KLEBEN \& DICHTEN},
  number    = {11},
  publisher = {Springer Nature},
  address   = {Cham},
  issn      = {2192-8681},
  doi       = {10.1007/s35145-021-0531-5},
  pages     = {12 -- 19},
  year      = {2021},
  language  = {de}
}
@article{Olbertz2021,
  author    = {Olbertz, Klaus},
  title     = {Wichtige arbeitsrechtliche Entwicklungen im Jahr 2020 : Der Jahresr{\"u}ckblick auf alles Wissenswerte im Arbeitsrecht des vergangenen Jahres},
  series = {NWB - Steuer- und Wirtschaftsrecht},
  journal   = {NWB - Steuer- und Wirtschaftsrecht},
  number    = {10},
  issn      = {0028-3460},
  pages     = {703 -- 715},
  year      = {2021},
  abstract  = {Im Anschluss an die arbeitsrechtlichen Jahres{\"u}bersichten der vergangenen Jahre (NWB 5/2019 S. 266; NWB 8/2020 S. 557) gibt der nachfolgende Beitrag einen {\"U}berblick {\"u}ber relevante Entwicklungen im Arbeitsrecht des Jahres 2020. Der erste Teil besch{\"a}ftigt sich hierbei mit gesetzlichen {\"A}nderungen. Neben Regelungen, die auf die COVID-19-Pandemie zur{\"u}ckgef{\"u}hrt werden k{\"o}nnen, hat der Gesetzgeber auch andere Vorhaben umgesetzt. So wurde u. a. das Arbeitnehmerentsenderecht reformiert. F{\"u}r Diskussionen sorgt(e) zudem das Gesetzesvorhaben zur Regelung mobiler Arbeit. Im zweiten Teil werden f{\"u}r die Praxis wichtige h{\"o}chstrichterliche Gerichtsentscheidungen zum Arbeitsrecht erl{\"a}utert, alphabetisch sortiert von A (wie Antidiskriminierungsrecht) bis U (wie Urlaub).},
  language  = {de}
}
@article{Olbertz2021,
  author    = {Olbertz, Klaus},
  title     = {Die Flexibilisierung von Arbeitszeit durch den Abruf von Arbeit : M{\"o}glichkeiten und Grenzen arbeitsvertraglicher Gestaltung zur Vermeidung von „Leerlaufzeiten"},
  series = {NWB - Steuer- und Wirtschaftsrecht},
  journal   = {NWB - Steuer- und Wirtschaftsrecht},
  number    = {15},
  issn      = {0028-3460},
  pages     = {1055 -- 1063},
  year      = {2021},
  abstract  = {Die Arbeitswelt ist im Umbruch. Der Bedarf an flexiblen Arbeitszeitmodellen nimmt stetig zu, wobei die Corona-Pandemie dieses Bed{\"u}rfnis nochmals versch{\"a}rft hat. Gerade auch in kleineren und mittleren Unternehmen w{\"a}chst die Notwendigkeit, den Einsatz der Besch{\"a}ftigten m{\"o}glichst bedarfsgerecht zu steuern, also bei guter Auftragslage mehr Arbeitszeit abzurufen und bei ausbleibenden Auftr{\"a}gen die Arbeitszeit zu reduzieren und somit bezahlte „Leerlaufzeiten" zu vermeiden. Der Gesetzgeber stellt den Arbeitgebern hierf{\"u}r das Instrument der sog. Abrufarbeit ( \S 12 Teilzeit- und Befristungsgesetz - TzBfG ) zur Verf{\"u}gung. In dem nachfolgenden Beitrag werden M{\"o}glichkeiten und Grenzen der Abrufarbeit skizziert und konkrete arbeitsvertragliche Gestaltungsm{\"o}glichkeiten aufgezeigt.},
  language  = {de}
}
@article{Olbertz2021,
  author    = {Olbertz, Klaus},
  title     = {Vertragsgestaltungen bei der Besch{\"a}ftigung von Rentnern in Unternehmen : (Befristete) Besch{\"a}ftigungsverh{\"a}ltnisse als sinnvolles Instrument zum Schließen von Personall{\"u}cken},
  series = {NWB - Steuer- und Wirtschaftsrecht},
  journal   = {NWB - Steuer- und Wirtschaftsrecht},
  number    = {25},
  issn      = {0028-3460},
  pages     = {1810 -- 1817},
  year      = {2021},
  language  = {de}
}
@article{BraunChengDoweyetal.2021,
  author    = {Braun, Sebastian and Cheng, Chi-Tsun and Dowey, Steve and Wollert, J{\"o}rg},
  title     = {Performance evaluation of skill-based order-assignment in production environments with multi-agent systems},
  series = {IEEE Journal of Emerging and Selected Topics in Industrial Electronics},
  journal   = {IEEE Journal of Emerging and Selected Topics in Industrial Electronics},
  number    = {Early Access},
  publisher = {IEEE},
  address   = {New York},
  issn      = {2687-9735},
  doi       = {10.1109/JESTIE.2021.3108524},
  year      = {2021},
  abstract  = {The fourth industrial revolution introduces disruptive technologies to production environments. One of these technologies are multi-agent systems (MASs), where agents virtualize machines. However, the agent's actual performances in production environments can hardly be estimated as most research has been focusing on isolated projects and specific scenarios. We address this gap by implementing a highly connected and configurable reference model with quantifiable key performance indicators (KPIs) for production scheduling and routing in single-piece workflows. Furthermore, we propose an algorithm to optimize the search of extrema in highly connected distributed systems. The benefits, limits, and drawbacks of MASs and their performances are evaluated extensively by event-based simulations against the introduced model, which acts as a benchmark. Even though the performance of the proposed MAS is, on average, slightly lower than the reference system, the increased flexibility allows it to find new solutions and deliver improved factory-planning outcomes. Our MAS shows an emerging behavior by using flexible production techniques to correct errors and compensate for bottlenecks. This increased flexibility offers substantial improvement potential. The general model in this paper allows the transfer of the results to estimate real systems or other models.},
  language  = {en}
}
@article{JahnkeRousselHombachetal.2016,
  author    = {Jahnke, Siegfried and Roussel, Johanna and Hombach, Thomas and Kochs, Johannes and Fischbach, Andreas and Huber, Gregor and Scharr, Hanno},
  title     = {phenoSeeder - A robot system for automated handling and phenotyping of individual seeds},
  series = {Plant physiology},
  volume    = {172},
  journal   = {Plant physiology},
  number    = {3},
  publisher = {Oxford University Press},
  address   = {Oxford},
  issn      = {0032-0889},
  doi       = {10.1104/pp.16.01122},
  pages     = {1358 -- 1370},
  year      = {2016},
  abstract  = {The enormous diversity of seed traits is an intriguing feature and critical for the overwhelming success of higher plants. In particular, seed mass is generally regarded to be key for seedling development but is mostly approximated by using scanning methods delivering only two-dimensional data, often termed seed size. However, three-dimensional traits, such as the volume or mass of single seeds, are very rarely determined in routine measurements. Here, we introduce a device named phenoSeeder, which enables the handling and phenotyping of individual seeds of very different sizes. The system consists of a pick-and-place robot and a modular setup of sensors that can be versatilely extended. Basic biometric traits detected for individual seeds are two-dimensional data from projections, three-dimensional data from volumetric measures, and mass, from which seed density is also calculated. Each seed is tracked by an identifier and, after phenotyping, can be planted, sorted, or individually stored for further evaluation or processing (e.g. in routine seed-to-plant tracking pipelines). By investigating seeds of Arabidopsis (Arabidopsis thaliana), rapeseed (Brassica napus), and barley (Hordeum vulgare), we observed that, even for apparently round-shaped seeds of rapeseed, correlations between the projected area and the mass of seeds were much weaker than between volume and mass. This indicates that simple projections may not deliver good proxies for seed mass. Although throughput is limited, we expect that automated seed phenotyping on a single-seed basis can contribute valuable information for applications in a wide range of wild or crop species, including seed classification, seed sorting, and assessment of seed quality.},
  language  = {en}
}
@article{Wrede2016,
  author    = {Wrede, Oliver},
  title     = {Continuity in travel information},
  series = {Information Design Journal},
  volume    = {22},
  journal   = {Information Design Journal},
  number    = {2},
  publisher = {John Benjamins},
  address   = {Amsterdam},
  issn      = {0142-5471},
  doi       = {10.1075/idj.22.2.09wre},
  pages     = {172 -- 178},
  year      = {2016},
  abstract  = {This article discusses the contrast between the information transportation companies provide to travellers and that of their brand messaging. Companies' brand messaging often portrays the service they provide as pleasant, stress free and perfect. Customers and users of the service, on the other hand, often describe their experience of the service as a negative one. This article suggests that the brand value would be greater if transportation companies paid more attention to the users' experience when designing their information systems, particularly in worst case scenarios.},
  language  = {en}
}
@article{NeuJanserKhatibietal.2017,
  author    = {Neu, Eugen and Janser, Frank and Khatibi, Akbar A. and Orifici, Adrian C.},
  title     = {Fully Automated Operational Modal Analysis using multi-stage clustering},
  series = {Mechanical Systems and Signal Processing},
  volume    = {Vol. 84, Part A},
  journal   = {Mechanical Systems and Signal Processing},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {0888-3270},
  doi       = {10.1016/j.ymssp.2016.07.031},
  pages     = {308 -- 323},
  year      = {2017},
  language  = {en}
}