@inproceedings{Dachwald2005,
  author    = {Dachwald, Bernd},
  title     = {Global optimization of low-thrust space missions using evolutionary neurocontrol},
  series = {Proceedings of the international workshop on global optimization},
  booktitle = {Proceedings of the international workshop on global optimization},
  pages     = {85 -- 90},
  year      = {2005},
  abstract  = {Low-thrust space propulsion systems enable flexible high-energy deep space missions, but the design and optimization of the interplanetary transfer trajectory is usually difficult. It involves much experience and expert knowledge because the convergence behavior of traditional local trajectory optimization methods depends strongly on an adequate initial guess. Within this extended abstract, evolutionary neurocontrol, a method that fuses artificial neural networks and evolutionary algorithms, is proposed as a smart global method for low-thrust trajectory optimization. It does not require an initial guess. The implementation of evolutionary neurocontrol is detailed and its performance is shown for an exemplary mission.},
  language  = {en}
}
@inproceedings{DachwaldBaturkinCoverstoneetal.2005,
  author    = {Dachwald, Bernd and Baturkin, Volodymyr and Coverstone, Victoria and Diedrich, Ben and Garbe, Gregory and G{\"o}rlich, Marianne and Leipold, Manfred and Lura, Franz and Macdonald, Malcolm and McInnes, Colin and Mengali, Giovanni and Quarta, Alessandro and Rios-Reyes, Leonel and Scheeres, Daniel J. and Seboldt, Wolfgang and Wie, Bong},
  title     = {Potential effects of optical solar sail degredation on trajectory design},
  series = {AAS/AIAA Astrodynamics Specialist},
  booktitle = {AAS/AIAA Astrodynamics Specialist},
  pages     = {1 -- 23},
  year      = {2005},
  abstract  = {The optical properties of the thin metalized polymer films that are projected for solar sails are assumed to be affected by the erosive effects of the space environment. Their degradation behavior in the real space environment, however, is to a considerable degree indefinite, because initial ground test results are controversial and relevant inspace tests have not been made so far. The standard optical solar sail models that are currently used for trajectory design do not take optical degradation into account, hence its potential effects on trajectory design have not been investigated so far. Nevertheless, optical degradation is important for high-fidelity solar sail mission design, because it decreases both the magnitude of the solar radiation pressure force acting on the sail and also the sail control authority. Therefore, we propose a simple parametric optical solar sail degradation model that describes the variation of the sail film's optical coefficients with time, depending on the sail film's environmental history, i.e., the radiation dose. The primary intention of our model is not to describe the exact behavior of specific film-coating combinations in the real space environment, but to provide a more general parametric framework for describing the general optical degradation behavior of solar sails. Using our model, the effects of different optical degradation behaviors on trajectory design are investigated for various exemplary missions.},
  language  = {en}
}
@incollection{HebelHerrmannRitzetal.2022,
  author    = {Hebel, Christoph and Herrmann, Ulf and Ritz, Thomas and R{\"o}th, Thilo and Anthrakidis, Anette and B{\"o}ker, J{\"o}rg and Franzke, Till and Grodzki, Thomas and Merkens, Torsten and Sch{\"o}ttler, Mirjam},
  title     = {FlexSHARE - Methodisches Framework zur innovativen Gestaltung der urbanen Mobilit{\"a}t durch Sharing- Angebote},
  series = {Transforming Mobility - What Next?},
  booktitle = {Transforming Mobility - What Next?},
  publisher = {Springer Gabler},
  address   = {Wiesbaden},
  isbn      = {978-3-658-36429-8},
  doi       = {10.1007/978-3-658-36430-4_10},
  pages     = {153 -- 169},
  year      = {2022},
  abstract  = {Das Ziel des INTERREG-Projektes „SHAREuregio" (FKZ: 34.EFRE-0300134) ist es, grenz{\"u}berschreitende Mobilit{\"a}t in der Euregio Rhein-Maas-Nord zu erm{\"o}glichen und zu f{\"o}rdern. Dazu soll ein elektromobiles Car- und Bikesharing- System entwickelt und in der Stadt M{\"o}nchengladbach, im Kreis Viersen sowie in den Gemeinden Roermond und Venlo (beide NL) zusammen mit den Partnern Wirtschaftsf{\"o}rderung M{\"o}nchengladbach, Wirtschaftsf{\"o}rderung f{\"u}r den Kreis Viersen, NEW AG, Goodmoovs (NL), Greenflux (NL) und der FH Aachen implementiert werden. Zun{\"a}chst richtet sich das Angebot, bestehend aus 40 Elektroautos und 40 Elektrofahrr{\"a}dern, an Unternehmen und wird nach einer Erprobungsphase, mit einer gr{\"o}ßeren Anzahl an Fahrzeugen, auch f{\"u}r Privatpersonen verf{\"u}gbar gemacht werden. Die Fahrzeuge stehen bei den jeweiligen Anwendungspartnern in Deutschland und den Niederlanden. Im Rahmen dieses Projektes hat die FH Aachen „FlexSHARE" entwickelt - ein methodisches Framework zur innovativen Gestaltung urbaner Sharing- Angebote. Das Framework erm{\"o}glicht es, anhand von messbaren Kenngr{\"o}ßen, bedarfsgerechte und auf die Region abgestimmte Sharing-Systeme zu entwickeln.},
  language  = {de}
}
@incollection{BauschatBennerKlingeetal.2022,
  author    = {Bauschat, J.-Michael and Benner, Miriam and Klinge, Henner and Ziegler, Simon},
  title     = {Urbane Mobilit{\"a}t entdeckt die 3. Dimension},
  series = {Transforming Mobility - What Next?},
  booktitle = {Transforming Mobility - What Next?},
  publisher = {Springer Gabler},
  address   = {Wiesbaden},
  isbn      = {978-3-658-36429-8},
  doi       = {10.1007/978-3-658-36430-4_53},
  pages     = {895 -- 916},
  year      = {2022},
  abstract  = {Der Themenkomplex urbane Mobilit{\"a}t ist getrieben durch den Verkehrsinfarkt in Ballungszentren, durch Luftverschmutzung und L{\"a}rm, sowie den Trend zum Leben in der Stadt in den st{\"a}dteplanerischen Fokus ger{\"u}ckt. Emissionsneutrale Antriebskonzepte in der Luftfahrt f{\"u}hren zu Ans{\"a}tzen Flugger{\"a}te einzusetzen, die batteriegetrieben vertikal aufsteigen und landen k{\"o}nnen. Flugphysikalisch und energetisch ist diese Technik nur dann sinnvoll, wenn es zwingende Gr{\"u}nde gibt (z.B. Rettungseins{\"a}tze), daher wird der flugphysikalische Hintergrund prinzipiell erl{\"a}utert. Es werden einige aktuelle Lufttransportkonzepte f{\"u}r eine urbane Personenbef{\"o}rderung vorgestellt. Sollte es verst{\"a}rkt zu Lufttransport {\"u}ber St{\"a}dten kommen, m{\"u}ssen betroffene Luftr{\"a}ume geordnet und {\"u}berwacht werden. Wie kompatibel Lufttransportsysteme mit den heute bereits relevanten urbanen Bef{\"o}rderungsmitteln sein m{\"u}ssen, wird kritisch diskutiert. Abschließend werden die Aspekte Akzeptanz durch die Kunden und Wirtschaftlichkeit ebenso angerissen, wie die hochproblematische Rohstoffgewinnung, die Entsorgung und das Recycling von Batterien.},
  language  = {de}
}
@article{BergmannMoehrenBraunetal.2023,
  author    = {Bergmann, Ole and M{\"o}hren, Felix and Braun, Carsten and Janser, Frank},
  title     = {On the influence of elasticity on swept propeller noise},
  series = {AIAA SCITECH 2023 Forum},
  journal   = {AIAA SCITECH 2023 Forum},
  publisher = {AIAA},
  doi       = {10.2514/6.2023-0210},
  year      = {2023},
  abstract  = {High aerodynamic efficiency requires propellers with high aspect ratios, while propeller sweep potentially reduces noise. Propeller sweep and high aspect ratios increase elasticity and coupling of structural mechanics and aerodynamics, affecting the propeller performance and noise. Therefore, this paper analyzes the influence of elasticity on forward-swept, backward-swept, and unswept propellers in hover conditions. A reduced-order blade element momentum approach is coupled with a one-dimensional Timoshenko beam theory and Farassat's formulation 1A. The results of the aeroelastic simulation are used as input for the aeroacoustic calculation. The analysis shows that elasticity influences noise radiation because thickness and loading noise respond differently to deformations. In the case of the backward-swept propeller, the location of the maximum sound pressure level shifts forward by 0.5 °, while in the case of the forward-swept propeller, it shifts backward by 0.5 °. Therefore, aeroacoustic optimization requires the consideration of propeller deformation.},
  language  = {en}
}
@inproceedings{HilleStumpfMayntzetal.2023,
  author    = {Hille, Sebastian and Stumpf, Eike and Mayntz, Joscha and Dahmann, Peter},
  title     = {Prediction of sound exposure caused by a landing motor glider with recuperating propellers},
  series = {AIAA SCITECH 2023 Forum},
  booktitle = {AIAA SCITECH 2023 Forum},
  publisher = {AIAA},
  doi       = {10.2514/6.2023-0211},
  year      = {2023},
  abstract  = {This paper presents an approach to predicting the sound exposure on the ground caused by a landing aircraft with recuperating propellers. The noise source along the trajectory of a flight specified for a steeper approach is simulated based on measurements of sound power levels and additional parameters of a single propeller placed in a wind tunnel. To validate the measured data/measurement results, these simulations are also supported by overflight measurements of a test aircraft. It is shown that the simple source models of propellers do not provide fully satisfactory results since the sound levels are estimated too low. Nevertheless, with a further reference comparison, margins for an acceptable increase in the sound power level of the aircraft on its now steeper approach path could be estimated. Thus, in this case, a +7 dB increase in SWL would not increase the SEL compared to the conventional approach within only 2 km ahead of the airfield.},
  language  = {en}
}
@inproceedings{HorikawaAshikagaYamaguchietal.2022,
  author    = {Horikawa, Atsushi and Ashikaga, Mitsugu and Yamaguchi, Masato and Ogino, Tomoyuki and Aoki, Shigeki and Wirsum, Manfred and Funke, Harald and Kusterer, Karsten},
  title     = {Combined heat and power supply demonstration of Micro-Mix Hydrogen Combustion Applied to M1A-17 Gas Turbine},
  series = {Proceedings of ASME Turbo Expo 2022: Turbomachinery Technical Conference and Exposition (GT2022) (Volume 3A)},
  booktitle = {Proceedings of ASME Turbo Expo 2022: Turbomachinery Technical Conference and Exposition (GT2022) (Volume 3A)},
  publisher = {American Society of Mechanical Engineers},
  address   = {Fairfield},
  isbn      = {978-0-7918-8599-4},
  doi       = {10.1115/GT2022-81620},
  pages     = {7 Seiten},
  year      = {2022},
  abstract  = {Kawasaki Heavy Industries, Ltd. (KHI), Aachen University of Applied Sciences, and B\&B-AGEMA GmbH have investigated the potential of low NOx micro-mix (MMX) hydrogen combustion and its application to an industrial gas turbine combustor. Engine demonstration tests of a MMX combustor for the M1A-17 gas turbine with a co-generation system were conducted in the hydrogen-fueled power generation plant in Kobe City, Japan. This paper presents the results of the commissioning test and the combined heat and power (CHP) supply demonstration. In the commissioning test, grid interconnection, loading tests and load cut-off tests were successfully conducted. All measurement results satisfied the Japanese environmental regulation values. Dust and soot as well as SOx were not detected. The NOx emissions were below 84 ppmv at 15 \% O2. The noise level at the site boundary was below 60 dB. The vibration at the site boundary was below 45 dB. During the combined heat and power supply demonstration, heat and power were supplied to neighboring public facilities with the MMX combustion technology and 100 \% hydrogen fuel. The electric power output reached 1800 kW at which the NOx emissions were 72 ppmv at 15 \% O2, and 60 \%RH. Combustion instabilities were not observed. The gas turbine efficiency was improved by about 1 \% compared to a non-premixed type combustor with water injection as NOx reduction method. During a total equivalent operation time of 1040 hours, all combustor parts, the M1A-17 gas turbine as such, and the co-generation system were without any issues.},
  language  = {en}
}
@inproceedings{MoehrenBergmannJanseretal.2023,
  author    = {M{\"o}hren, Felix and Bergmann, Ole and Janser, Frank and Braun, Carsten},
  title     = {On the determination of harmonic propeller loads},
  series = {AIAA SCITECH 2023 Forum},
  booktitle = {AIAA SCITECH 2023 Forum},
  publisher = {AIAA},
  doi       = {10.2514/6.2023-2404},
  pages     = {12 Seiten},
  year      = {2023},
  abstract  = {Dynamic loads significantly impact the structural design of propeller blades due to fatigue and static strength. Since propellers are elastic structures, deformations and aerodynamic loads are coupled. In the past, propeller manufacturers established procedures to determine unsteady aerodynamic loads and the structural response with analytical steady-state calculations. According to the approach, aeroelastic coupling primarily consists of torsional deformations. They neglect bending deformations, deformation velocities, and inertia terms. This paper validates the assumptions above for a General Aviation propeller and a lift propeller for urban air mobility or large cargo drones. Fully coupled reduced-order simulations determine the dynamic loads in the time domain. A quasi-steady blade element momentum approach transfers loads to one-dimensional finite beam elements. The simulation results are in relatively good agreement with the analytical method for the General Aviation propeller but show increasing errors for the slender lift propeller. The analytical approach is modified to consider the induced velocities. Still, inertia and velocity proportional terms play a significant role for the lift propeller due to increased elasticity. The assumption that only torsional deformations significantly impact the dynamic loads of propellers is not valid. Adequate determination of dynamic loads of such designs requires coupled aeroelastic simulations or advanced analytical procedures.},
  language  = {en}
}
@article{DickhoffHorikawaFunke2021,
  author    = {Dickhoff, Jens and Horikawa, Atsushi and Funke, Harald},
  title     = {Hydrogen Combustion - new DLE Combustor Addresses NOx Emissions and Flashback},
  series = {Turbomachinery international : the global journal of energy equipment},
  volume    = {62},
  journal   = {Turbomachinery international : the global journal of energy equipment},
  number    = {4},
  publisher = {MJH Life Sciences},
  address   = {Cranbury},
  issn      = {2767-2328},
  pages     = {26 -- 27},
  year      = {2021},
  language  = {en}
}
@article{FunkeBeckmann2022,
  author    = {Funke, Harald and Beckmann, Nils},
  title     = {Flexible fuel operation of a Dry-Low-NOx Micromix Combustor with Variable Hydrogen Methane Mixture},
  series = {International Journal of Gas Turbine, Propulsion and Power Systems},
  volume    = {13},
  journal   = {International Journal of Gas Turbine, Propulsion and Power Systems},
  number    = {2},
  issn      = {1882-5079},
  pages     = {1 -- 7},
  year      = {2022},
  abstract  = {The role of hydrogen (H2) as a carbon-free energy carrier is discussed since decades for reducing greenhouse gas emissions. As bridge technology towards a hydrogen-based energy supply, fuel mixtures of natural gas or methane (CH4) and hydrogen are possible. The paper presents the first test results of a low-emission Micromix combustor designed for flexible-fuel operation with variable H2/CH4 mixtures. The numerical and experimental approach for considering variable fuel mixtures instead of recently investigated pure hydrogen is described. In the experimental studies, a first generation FuelFlex Micromix combustor geometry is tested at atmospheric pressure at gas turbine operating conditions corresponding to part- and full-load. The H2/CH4 fuel mixture composition is varied between 57 and 100 vol.\% hydrogen content. Despite the challenges flexible-fuel operation poses onto the design of a combustion system, the evaluated FuelFlex Micromix prototype shows a significant low NOx performance},
  language  = {en}
}
@inproceedings{FunkeBeckmannStefanetal.2023,
  author    = {Funke, Harald and Beckmann, Nils and Stefan, Lukas and Keinz, Jan},
  title     = {Hydrogen combustor integration study for a medium range aircraft engine using the dry-low NOx "Micromix" combustion principle},
  series = {Proceedings of the ASME Turbo Expo 2023: Turbomachinery Technical Conference and Exposition. Volume 1: Aircraft Engine. Boston, Massachusetts, USA. June 26-30, 2023},
  booktitle = {Proceedings of the ASME Turbo Expo 2023: Turbomachinery Technical Conference and Exposition. Volume 1: Aircraft Engine. Boston, Massachusetts, USA. June 26-30, 2023},
  publisher = {ASME},
  address   = {New York},
  isbn      = {978-0-7918-8693-9},
  doi       = {10.1115/GT2023-102370},
  pages     = {12 Seiten},
  year      = {2023},
  abstract  = {The feasibility study presents results of a hydrogen combustor integration for a Medium-Range aircraft engine using the Dry-Low-NOₓ Micromix combustion principle. Based on a simplified Airbus A320-type flight mission, a thermodynamic performance model of a kerosene and a hydrogen-powered V2530-A5 engine is used to derive the thermodynamic combustor boundary conditions. A new combustor design using the Dry-Low NOx Micromix principle is investigated by slice model CFD simulations of a single Micromix injector for design and off-design operation of the engine. Combustion characteristics show typical Micromix flame shapes and good combustion efficiencies for all flight mission operating points. Nitric oxide emissions are significant below ICAO CAEP/8 limits. For comparison of the Emission Index (EI) for NOₓ emissions between kerosene and hydrogen operation, an energy (kerosene) equivalent Emission Index is used. A full 15° sector model CFD simulation of the combustion chamber with multiple Micromix injectors including inflow homogenization and dilution and cooling air flows investigates the combustor integration effects, resulting NOₓ emission and radial temperature distributions at the combustor outlet. The results show that the integration of a Micromix hydrogen combustor in actual aircraft engines is feasible and offers, besides CO₂ free combustion, a significant reduction of NOₓ emissions compared to kerosene operation.},
  language  = {en}
}
@inproceedings{GehlerOberBloebaumDachwald2009,
  author    = {Gehler, M. and Ober-Bl{\"o}baum, S. and Dachwald, Bernd},
  title     = {Application of discrete mechanics and optimal control to spacecraft in non-keplerian motion around small solar system bodies},
  series = {Procceedings of the 60th International Astronautical Congress},
  booktitle = {Procceedings of the 60th International Astronautical Congress},
  publisher = {Elsevier},
  address   = {Amsterdam},
  isbn      = {978-161567908-9},
  pages     = {1360 -- 1371},
  year      = {2009},
  abstract  = {Prolonged operations close to small solar system bodies require a sophisticated control logic to minimize propellant mass and maximize operational efficiency. A control logic based on Discrete Mechanics and Optimal Control (DMOC) is proposed and applied to both conventionally propelled and solar sail spacecraft operating at an arbitrarily shaped asteroid in the class of Itokawa. As an example, stand-off inertial hovering is considered, recently identified as a challenging part of the Marco Polo mission. The approach is easily extended to stand-off orbits. We show that DMOC is applicable to spacecraft control at small objects, in particular with regard to the fact that the changes in gravity are exploited by the algorithm to optimally control the spacecraft position. Furthermore, we provide some remarks on promising developments.},
  language  = {en}
}
@inproceedings{DachwaldWurm2009,
  author    = {Dachwald, Bernd and Wurm, P.},
  title     = {Design concept and modeling of an advanced solar photon thruster},
  series = {Advances in the Astronautical Sciences},
  booktitle = {Advances in the Astronautical Sciences},
  publisher = {American Astronautical Society},
  address   = {San Diego, Calif.},
  isbn      = {978-087703554-1},
  issn      = {00653438},
  pages     = {723 -- 740},
  year      = {2009},
  abstract  = {The so-called "compound solar sail", also known as "Solar Photon Thruster" (SPT), holds the potential of providing significant performance advantages over the flat solar sail. Previous SPT design concepts, however, do not consider shadowing effects and multiple reflections of highly concentrated solar radiation that would inevitably destroy the gossamer sail film. In this paper, we propose a novel advanced SPT (ASPT) design concept that does not suffer from these oversimplifications. We present the equations that describe the thrust force acting on such a sail system and compare its performance with respect to the conventional flat solar sail.},
  language  = {en}
}
@incollection{Dachwald2017,
  author    = {Dachwald, Bernd},
  title     = {Light propulsion systems for spacecraft},
  series = {Optical nano and micro actuator technology},
  booktitle = {Optical nano and micro actuator technology},
  editor    = {Knopf, George K. and Otani, Yukitoshi},
  publisher = {CRC Press},
  address   = {Boca Raton},
  isbn      = {9781315217628 (eBook)},
  pages     = {577 -- 598},
  year      = {2017},
  language  = {en}
}
@inproceedings{DachwaldWurm2009,
  author    = {Dachwald, Bernd and Wurm, P.},
  title     = {Mission analysis for an advanced solar photon thruster},
  series = {60th International Astronautical Congress 2009, IAC 2009},
  volume    = {Vol. 8},
  booktitle = {60th International Astronautical Congress 2009, IAC 2009},
  publisher = {Elsevier},
  address   = {Amsterdam},
  isbn      = {978-161567908-9},
  pages     = {6838 -- 6851},
  year      = {2009},
  abstract  = {The so-called "compound solar sail", also known as "Solar Photon Thruster" (SPT), is a solar sail design concept, for which the two basic functions of the solar sail, namely light collection and thrust direction, are uncoupled. In this paper, we introduce a novel SPT concept, termed the Advanced Solar Photon Thruster (ASPT). This model does not suffer from the simplified assumptions that have been made for the analysis of compound solar sails in previous studies. We present the equations that describe the force, which acts on the ASPT. After a detailed design analysis, the performance of the ASPT with respect to the conventional flat solar sail (FSS) is investigated for three interplanetary mission scenarios: An Earth-Venus rendezvous, where the solar sail has to spiral towards the Sun, an Earth-Mars rendezvous, where the solar sail has to spiral away from the Sun, and an Earth-NEA rendezvous (to near-Earth asteroid 1996FG3), where a large orbital eccentricity change is required. The investigated solar sails have realistic near-term characteristic accelerations between 0.1 and 0.2mm/s2. Our results show that a SPT is not superior to the flat solar sail unless very idealistic assumptions are made.},
  language  = {en}
}
@article{KhayyamJamaliBabHadiasharetal.2020,
  author    = {Khayyam, Hamid and Jamali, Ali and Bab-Hadiashar, Alireza and Esch, Thomas and Ramakrishna, Seeram and Jalil, Mahdi and Naebe, Minoo},
  title     = {A Novel Hybrid Machine Learning Algorithm for Limited and Big Data Modelling with Application in Industry 4.0},
  series = {IEEE Access},
  journal   = {IEEE Access},
  publisher = {IEEE},
  address   = {New York, NY},
  isbn      = {2169-3536},
  doi       = {10.1109/ACCESS.2020.2999898},
  pages     = {1 -- 12},
  year      = {2020},
  abstract  = {To meet the challenges of manufacturing smart products, the manufacturing plants have been radically changed to become smart factories underpinned by industry 4.0 technologies. The transformation is assisted by employment of machine learning techniques that can deal with modeling both big or limited data. This manuscript reviews these concepts and present a case study that demonstrates the use of a novel intelligent hybrid algorithms for Industry 4.0 applications with limited data. In particular, an intelligent algorithm is proposed for robust data modeling of nonlinear systems based on input-output data. In our approach, a novel hybrid data-driven combining the Group-Method of Data-Handling and Singular-Value Decomposition is adapted to find an offline deterministic model combined with Pareto multi-objective optimization to overcome the overfitting issue. An Unscented-Kalman-Filter is also incorporated to update the coefficient of the deterministic model and increase its robustness against data uncertainties. The effectiveness of the proposed method is examined on a set of real industrial measurements.},
  language  = {en}
}
@inproceedings{GoettenFingerHavermannetal.2020,
  author    = {G{\"o}tten, Falk and Finger, Felix and Havermann, Marc and Braun, Carsten and Marino, Matthew and Bil, Cees},
  title     = {Full Configuration Drag Estimation of Small-to-Medium Range UAVs and its Impact on Initial Sizing Optimization},
  series = {Deutscher Luft- und Raumfahrtkongress - DLRK 2020},
  booktitle = {Deutscher Luft- und Raumfahrtkongress - DLRK 2020},
  year      = {2020},
  language  = {en}
}
@inproceedings{BergmannGoettenBraunetal.2022,
  author    = {Bergmann, Ole and G{\"o}tten, Falk and Braun, Carsten and Janser, Frank},
  title     = {Comparison and evaluation of blade element methods against RANS simulations and test data},
  series = {CEAS Aeronautical Journal},
  volume    = {13},
  booktitle = {CEAS Aeronautical Journal},
  publisher = {Springer},
  address   = {Wien},
  issn      = {1869-5590 (Online)},
  doi       = {10.1007/s13272-022-00579-1},
  pages     = {535 -- 557},
  year      = {2022},
  abstract  = {This paper compares several blade element theory (BET) method-based propeller simulation tools, including an evaluation against static propeller ground tests and high-fidelity Reynolds-Average Navier Stokes (RANS) simulations. Two proprietary propeller geometries for paraglider applications are analysed in static and flight conditions. The RANS simulations are validated with the static test data and used as a reference for comparing the BET in flight conditions. The comparison includes the analysis of varying 2D aerodynamic airfoil parameters and different induced velocity calculation methods. The evaluation of the BET propeller simulation tools shows the strength of the BET tools compared to RANS simulations. The RANS simulations underpredict static experimental data within 10\% relative error, while appropriate BET tools overpredict the RANS results by 15-20\% relative error. A variation in 2D aerodynamic data depicts the need for highly accurate 2D data for accurate BET results. The nonlinear BET coupled with XFOIL for the 2D aerodynamic data matches best with RANS in static operation and flight conditions. The novel BET tool PropCODE combines both approaches and offers further correction models for highly accurate static and flight condition results.},
  language  = {en}
}
@article{KreyerMuellerEsch2020,
  author    = {Kreyer, J{\"o}rg and M{\"u}ller, Marvin and Esch, Thomas},
  title     = {A Calculation Methodology for Predicting Exhaust Mass Flows and Exhaust Temperature Profiles for Heavy-Duty Vehicles},
  series = {SAE International Journal of Commercial Vehicles},
  volume    = {13},
  journal   = {SAE International Journal of Commercial Vehicles},
  number    = {2},
  publisher = {SAE International},
  address   = {Warrendale, Pa.},
  issn      = {1946-3928},
  doi       = {10.4271/02-13-02-0009},
  pages     = {129 -- 143},
  year      = {2020},
  abstract  = {The predictive control of commercial vehicle energy management systems, such as vehicle thermal management or waste heat recovery (WHR) systems, are discussed on the basis of information sources from the field of environment recognition and in combination with the determination of the vehicle system condition. In this article, a mathematical method for predicting the exhaust gas mass flow and the exhaust gas temperature is presented based on driving data of a heavy-duty vehicle. The prediction refers to the conditions of the exhaust gas at the inlet of the exhaust gas recirculation (EGR) cooler and at the outlet of the exhaust gas aftertreatment system (EAT). The heavy-duty vehicle was operated on the motorway to investigate the characteristic operational profile. In addition to the use of road gradient profile data, an evaluation of the continuously recorded distance signal, which represents the distance between the test vehicle and the road user ahead, is included in the prediction model. Using a Fourier analysis, the trajectory of the vehicle speed is determined for a defined prediction horizon. To verify the method, a holistic simulation model consisting of several hierarchically structured submodels has been developed. A map-based submodel of a combustion engine is used to determine the EGR and EAT exhaust gas mass flows and exhaust gas temperature profiles. All simulation results are validated on the basis of the recorded vehicle and environmental data. Deviations from the predicted values are analyzed and discussed.},
  language  = {en}
}
@article{GoettenHavermannBraunetal.2020,
  author    = {G{\"o}tten, Falk and Havermann, Marc and Braun, Carsten and Marino, Matthew and Bil, Cees},
  title     = {Wind-tunnel and CFD investigations of UAV landing gears and turrets - Improvements in empirical drag estimation},
  series = {Aerospace Science and Technology},
  volume    = {107},
  journal   = {Aerospace Science and Technology},
  number    = {Art. 106306},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {1270-9638},
  doi       = {10.1016/j.ast.2020.106306},
  year      = {2020},
  abstract  = {This paper analyzes the drag characteristics of several landing gear and turret configurations that are representative of unmanned aircraft tricycle landing gears and sensor turrets. A variety of these components were constructed via 3D-printing and analyzed in a wind-tunnel measurement campaign. Both turrets and landing gears were attached to a modular fuselage that supported both isolated components and multiple components at a time. Selected cases were numerically investigated with a Reynolds-averaged Navier-Stokes approach that showed good accuracy when compared to wind-tunnel data. The drag of main gear struts could be significantly reduced via streamlining their cross-sectional shape and keeping load carrying capabilities similar. The attachment of wheels introduced interference effects that increased strut drag moderately but significantly increased wheel drag compared to isolated cases. Very similar behavior was identified for front landing gears. The drag of an electro-optical and infrared sensor turret was found to be much higher than compared to available data of a clean hemisphere-cylinder combination. This turret drag was merely influenced by geometrical features like sensor surfaces and the rotational mechanism. The new data of this study is used to develop simple drag estimation recommendations for main and front landing gear struts and wheels as well as sensor turrets. These recommendations take geometrical considerations and interference effects into account.},
  language  = {en}
}
@article{GoettenHavermannBraunetal.2020,
  author    = {G{\"o}tten, Falk and Havermann, Marc and Braun, Carsten and Marino, Matthew and Bil, Cees},
  title     = {Improved Form Factor for Drag Estimation of Fuselages with Various Cross Sections},
  series = {Journal of Aircraft},
  journal   = {Journal of Aircraft},
  publisher = {AIAA},
  address   = {Reston, Va.},
  issn      = {1533-3868},
  doi       = {10.2514/1.C036032},
  pages     = {1 -- 13},
  year      = {2020},
  abstract  = {The paper presents an aerodynamic investigation of 70 different streamlined bodies with fineness ratios ranging from 2 to 10. The bodies are chosen to idealize both unmanned and small manned aircraft fuselages and feature cross-sectional shapes that vary from circular to quadratic. The study focuses on friction and pressure drag in dependency of the individual body's fineness ratio and cross section. The drag forces are normalized with the respective body's wetted area to comply with an empirical drag estimation procedure. Although the friction drag coefficient then stays rather constant for all bodies, their pressure drag coefficients decrease with an increase in fineness ratio. Referring the pressure drag coefficient to the bodies' cross-sectional areas shows a distinct pressure drag minimum at a fineness ratio of about three. The pressure drag of bodies with a quadratic cross section is generally higher than for bodies of revolution. The results are used to derive an improved form factor that can be employed in a classic empirical drag estimation method. The improved formulation takes both the fineness ratio and cross-sectional shape into account. It shows superior accuracy in estimating streamlined body drag when compared with experimental data and other form factor formulations of the literature.},
  language  = {en}
}
@article{FingerBraunBil2020,
  author    = {Finger, Felix and Braun, Carsten and Bil, Cees},
  title     = {Comparative assessment of parallel-hybrid-electric propulsion systems for four different aircraft},
  series = {Journal of Aircraft},
  volume    = {57},
  journal   = {Journal of Aircraft},
  number    = {5},
  publisher = {AIAA},
  address   = {Reston, Va.},
  issn      = {1533-3868},
  doi       = {10.2514/1.C035897},
  year      = {2020},
  abstract  = {Until electric energy storage systems are ready to allow fully electric aircraft, the combination of combustion engine and electric motor as a hybrid-electric propulsion system seems to be a promising intermediate solution. Consequently, the design space for future aircraft is expanded considerably, as serial hybrid-electric, parallel hybrid-electric, fully electric, and conventional propulsion systems must all be considered. While the best propulsion system depends on a multitude of requirements and considerations, trends can be observed for certain types of aircraft and certain types of missions. This Paper provides insight into some factors that drive a new design toward either conventional or hybrid propulsion systems. General aviation aircraft, regional transport aircraft vertical takeoff and landing air taxis, and unmanned aerial vehicles are chosen as case studies. Typical missions for each class are considered, and the aircraft are analyzed regarding their takeoff mass and primary energy consumption. For these case studies, a high-level approach is chosen, using an initial sizing methodology. Only parallel-hybrid-electric powertrains are taken into account. Aeropropulsive interaction effects are neglected. Results indicate that hybrid-electric propulsion systems should be considered if the propulsion system is sized by short-duration power constraints. However, if the propulsion system is sized by a continuous power requirement, hybrid-electric systems offer hardly any benefit.},
  language  = {en}
}
@inproceedings{GeibenGoettenHavermann2020,
  author    = {Geiben, Benedikt and G{\"o}tten, Falk and Havermann, Marc},
  title     = {Aerodynamic analysis of a winged sub-orbital spaceplane},
  series = {Deutscher Luft- und Raumfahrtkongress - DLRK 2020},
  booktitle = {Deutscher Luft- und Raumfahrtkongress - DLRK 2020},
  year      = {2020},
  language  = {en}
}
@inproceedings{HippeFingerGoettenetal.2020,
  author    = {Hippe, Jonas and Finger, Felix and G{\"o}tten, Falk and Braun, Carsten},
  title     = {Propulsion System Qualification of a 25 kg VTOL-UAV: Hover Performance of Single and Coaxial Rotors and Wind-Tunnel Experiments on Cruise Propellers},
  series = {Deutscher Luft- und Raumfahrtkongress - DLRK 2020},
  booktitle = {Deutscher Luft- und Raumfahrtkongress - DLRK 2020},
  year      = {2020},
  language  = {en}
}
@incollection{Blome2013,
  author    = {Blome, Hans-Joachim},
  title     = {Die Tragweite der physikalischen Kosmologie},
  series = {Exploring Uncertainty},
  booktitle = {Exploring Uncertainty},
  publisher = {Springer Gabler},
  address   = {Wiesbaden},
  isbn      = {978-3-658-00897-0},
  doi       = {10.1007/978-3-658-00897-0_6},
  pages     = {105 -- 150},
  year      = {2013},
  language  = {de}
}
@inproceedings{FingerGoettenBraunetal.2019,
  author    = {Finger, Felix and G{\"o}tten, Falk and Braun, Carsten and Bil, C.},
  title     = {On Aircraft Design Under the Consideration of Hybrid-Electric Propulsion Systems},
  series = {APISAT 2018: The Proceedings of the 2018 Asia-Pacific International Symposium on Aerospace Technology (APISAT 2018)},
  booktitle = {APISAT 2018: The Proceedings of the 2018 Asia-Pacific International Symposium on Aerospace Technology (APISAT 2018)},
  publisher = {Springer},
  address   = {Singapore},
  isbn      = {978-981-13-3305-7},
  doi       = {10.1007/978-981-13-3305-7_99},
  pages     = {1261 -- 1272},
  year      = {2019},
  abstract  = {A hybrid-electric propulsion system combines the advantages of fuel-based systems and battery powered systems and offers new design freedom. To take full advantage of this technology, aircraft designers must be aware of its key differences, compared to conventional, carbon-fuel based, propulsion systems. This paper gives an overview of the challenges and potential benefits associated with the design of aircraft that use hybrid-electric propulsion systems. It offers an introduction of the most popular hybrid-electric propulsion architectures and critically assess them against the conventional and fully electric propulsion configurations. The effects on operational aspects and design aspects are covered. Special consideration is given to the application of hybrid-electric propulsion technology to both unmanned and vertical take-off and landing aircraft. The authors conclude that electric propulsion technology has the potential to revolutionize aircraft design. However, new and innovative methods must be researched, to realize the full benefit of the technology.},
  language  = {en}
}
@inproceedings{GoettenFingerBraunetal.2019,
  author    = {G{\"o}tten, Falk and Finger, Felix and Braun, Carsten and Havermann, Marc and Bil, C. and Gomez, F.},
  title     = {Empirical Correlations for Geometry Build-Up of Fixed Wing Unmanned Air Vehicles},
  series = {APISAT 2018: The Proceedings of the 2018 Asia-Pacific International Symposium on Aerospace Technology (APISAT 2018)},
  booktitle = {APISAT 2018: The Proceedings of the 2018 Asia-Pacific International Symposium on Aerospace Technology (APISAT 2018)},
  publisher = {Springer},
  address   = {Singapore},
  isbn      = {978-981-13-3305-7},
  doi       = {10.1007/978-981-13-3305-7_109},
  pages     = {1365 -- 1381},
  year      = {2019},
  abstract  = {The results of a statistical investigation of 42 fixed-wing, small to medium sized (20 kg-1000 kg) reconnaissance unmanned air vehicles (UAVs) are presented. Regression analyses are used to identify correlations of the most relevant geometry dimensions with the UAV's maximum take-off mass. The findings allow an empirical based geometry-build up for a complete unmanned aircraft by referring to its take-off mass only. This provides a bridge between very early design stages (initial sizing) and the later determination of shapes and dimensions. The correlations might be integrated into a UAV sizing environment and allow designers to implement more sophisticated drag and weight estimation methods in this process. Additional information on correlation factors for a rough drag estimation methodology indicate how this technique can significantly enhance the accuracy of early design iterations.},
  language  = {en}
}
@article{GazdaMaurischat2020,
  author    = {Gazda, Quentin and Maurischat, Andreas},
  title     = {Special functions and Gauss-Thakur sums in higher rank and dimension},
  publisher = {De Gruyter},
  address   = {Berlin},
  pages     = {26 Seiten},
  year      = {2020},
  language  = {en}
}
@article{GoettenFingerHavermannetal.2021,
  author    = {G{\"o}tten, Falk and Finger, Felix and Havermann, Marc and Braun, Carsten and Marino, M. and Bil, C.},
  title     = {Full configuration drag estimation of short-to-medium range fixed-wing UAVs and its impact on initial sizing optimization},
  series = {CEAS Aeronautical Journal},
  volume    = {12},
  journal   = {CEAS Aeronautical Journal},
  publisher = {Springer},
  address   = {Berlin},
  issn      = {1869-5590 (Online)},
  doi       = {10.1007/s13272-021-00522-w},
  pages     = {589 -- 603},
  year      = {2021},
  abstract  = {The paper presents the derivation of a new equivalent skin friction coefficient for estimating the parasitic drag of short-to-medium range fixed-wing unmanned aircraft. The new coefficient is derived from an aerodynamic analysis of ten different unmanned aircraft used for surveillance, reconnaissance, and search and rescue missions. The aircraft is simulated using a validated unsteady Reynolds-averaged Navier Stokes approach. The UAV's parasitic drag is significantly influenced by the presence of miscellaneous components like fixed landing gears or electro-optical sensor turrets. These components are responsible for almost half of an unmanned aircraft's total parasitic drag. The new equivalent skin friction coefficient accounts for these effects and is significantly higher compared to other aircraft categories. It is used to initially size an unmanned aircraft for a typical reconnaissance mission. The improved parasitic drag estimation yields a much heavier unmanned aircraft when compared to the sizing results using available drag data of manned aircraft.},
  language  = {en}
}
@inproceedings{ThomaFisherBraun2020,
  author    = {Thoma, Andreas and Fisher, Alex and Braun, Carsten},
  title     = {Improving the px4 avoid algorithm by bio-inspired flight strategies},
  series = {DLRK2020 - „Luft- und Raumfahrt - Verantwortung in allen Dimensionen"},
  booktitle = {DLRK2020 - „Luft- und Raumfahrt - Verantwortung in allen Dimensionen"},
  pages     = {10 Seiten},
  year      = {2020},
  language  = {en}
}
@inproceedings{EnglhardWeberArent2021,
  author    = {Englhard, Markus and Weber, Tobias and Arent, Jan-Christoph},
  title     = {Efficiency enhancement for CFRP-Prepregautoclave manufacturing by means of simulation-assisted loading optimization},
  series = {Proceedings of SAMPE Europe Conference 2021},
  booktitle = {Proceedings of SAMPE Europe Conference 2021},
  pages     = {8 Seiten},
  year      = {2021},
  abstract  = {A new method for improved autoclave loading within the restrictive framework of helicopter manufacturing is proposed. It is derived from experimental and numerical studies of the curing process and aims at optimizing tooling positions in the autoclave for fast and homogeneous heat-up. The mold positioning is based on two sets of information. The thermal properties of the molds, which can be determined via semi-empirical thermal simulation. The second information is a previously determined distribution of heat transfer coefficients inside the autoclave. Finally, an experimental proof of concept is performed to show a cycle time reduction of up to 31\% using the proposed methodology.},
  language  = {en}
}
@inproceedings{HauggKreyerKemperetal.2020,
  author    = {Haugg, Albert Thomas and Kreyer, J{\"o}rg and Kemper, Hans and Hatesuer, Katerina and Esch, Thomas},
  title     = {Heat exchanger for ORC. adaptability and optimisation potentials},
  series = {IIR International Rankine 2020 Conference},
  booktitle = {IIR International Rankine 2020 Conference},
  doi       = {10.18462/iir.rankine.2020.1224},
  pages     = {10 Seiten},
  year      = {2020},
  abstract  = {The recovery of waste heat requires heat exchangers to extract it from a liquid or gaseous medium into another working medium, a refrigerant. In Organic Rankine Cycles (ORC) on Combustion Engines there are two major heat sources, the exhaust gas and the water/glycol fluid from the engine's cooling circuit. A heat exchanger design must be adapted to the different requirements and conditions resulting from the heat sources, fluids, system configurations, geometric restrictions, and etcetera. The Stacked Shell Cooler (SSC) is a new and very specific design of a plate heat exchanger, created by AKG, which allows with a maximum degree of freedom the optimization of heat exchange rate and the reduction of the related pressure drop. This optimization in heat exchanger design for ORC systems is even more important, because it reduces the energy consumption of the system and therefore maximizes the increase in overall efficiency of the engine.},
  language  = {en}
}
@article{Maurischat2022,
  author    = {Maurischat, Andreas},
  title     = {Algebraic independence of the Carlitz period and its hyperderivatives},
  series = {Journal of Number Theory},
  volume    = {240},
  journal   = {Journal of Number Theory},
  publisher = {Elsevier},
  address   = {Orlando, Fla.},
  issn      = {0022-314X},
  doi       = {10.1016/j.jnt.2022.01.006},
  pages     = {145 -- 162},
  year      = {2022},
  language  = {en}
}
@article{FingerGoettenBraunetal.2020,
  author    = {Finger, Felix and G{\"o}tten, Falk and Braun, Carsten and Bil, Cees},
  title     = {Mass, primary energy, and cost: the impact of optimization objectives on the initial sizing of hybrid-electric general aviation aircraft},
  series = {CEAS Aeronautical Journal},
  volume    = {2020},
  journal   = {CEAS Aeronautical Journal},
  number    = {11},
  publisher = {Springer},
  address   = {Heidelberg},
  issn      = {1869-5590},
  doi       = {10.1007/s13272-020-00449-8},
  pages     = {713 -- 730},
  year      = {2020},
  abstract  = {For short take-off and landing (STOL) aircraft, a parallel hybrid-electric propulsion system potentially offers superior performance compared to a conventional propulsion system, because the short-take-off power requirement is much higher than the cruise power requirement. This power-matching problem can be solved with a balanced hybrid propulsion system. However, there is a trade-off between wing loading, power loading, the level of hybridization, as well as range and take-off distance. An optimization method can vary design variables in such a way that a minimum of a particular objective is attained. In this paper, a comparison between the optimization results for minimum mass, minimum consumed primary energy, and minimum cost is conducted. A new initial sizing algorithm for general aviation aircraft with hybrid-electric propulsion systems is applied. This initial sizing methodology covers point performance, mission performance analysis, the weight estimation process, and cost estimation. The methodology is applied to the design of a STOL general aviation aircraft, intended for on-demand air mobility operations. The aircraft is sized to carry eight passengers over a distance of 500 km, while able to take off and land from short airstrips. Results indicate that parallel hybrid-electric propulsion systems must be considered for future STOL aircraft.},
  language  = {en}
}
@inproceedings{HoevelerJanser2016,
  author    = {Hoeveler, Bastian and Janser, Frank},
  title     = {The aerodynamically optimized design of a fan-in-wing duct},
  series = {Applied Aerodynamics Research Conference 2016, Bristol, GB, Jul 19-21, 2016},
  booktitle = {Applied Aerodynamics Research Conference 2016, Bristol, GB, Jul 19-21, 2016},
  isbn      = {1-85768-371-4},
  pages     = {1 -- 10},
  year      = {2016},
  language  = {en}
}
@inproceedings{GrundmannBauerBorchersetal.2019,
  author    = {Grundmann, Jan Thimo and Bauer, Wlademar and Borchers, Kai and Dumont, Etienne and Grimm, Christian D. and Ho, Tra-Mi and Jahnke, Rico and Koch, Aaron D. and Lange, Caroline and Maiwald, Volker and Meß, Jan-Gerd and Mikulz, Eugen and Quantius, Dominik and Reershemius, Siebo and Renger, Thomas and Sasaki, Kaname and Seefeldt, Patric and Spietz, Peter and Spr{\"o}witz, Tom and Sznajder, Maciej and Toth, Norbert and Ceriotti, Matteo and McInnes, Colin and Peloni, Alessandro and Biele, Jens and Krause, Christian and Dachwald, Bernd and Hercik, David and Lichtenheldt, Roy and Wolff, Friederike and Koncz, Alexander and Pelivan, Ivanka and Schmitz, Nicole and Boden, Ralf and Riemann, Johannes and Seboldt, Wolfgang and Wejmo, Elisabet and Ziach, Christian and Mikschl, Tobias and Montenegro, Sergio and Ruffer, Michael and Cordero, Federico and Tardivel, Simon},
  title     = {Solar sails for planetary defense \& high-energy missions},
  series = {IEEE Aerospace Conference Proceedings},
  booktitle = {IEEE Aerospace Conference Proceedings},
  doi       = {10.1109/AERO.2019.8741900},
  pages     = {1 -- 21},
  year      = {2019},
  abstract  = {20 years after the successful ground deployment test of a (20 m) 2 solar sail at DLR Cologne, and in the light of the upcoming U.S. NEAscout mission, we provide an overview of the progress made since in our mission and hardware design studies as well as the hardware built in the course of our solar sail technology development. We outline the most likely and most efficient routes to develop solar sails for useful missions in science and applications, based on our developed `now-term' and near-term hardware as well as the many practical and managerial lessons learned from the DLR-ESTEC Gossamer Roadmap. Mission types directly applicable to planetary defense include single and Multiple NEA Rendezvous ((M)NR) for precursor, monitoring and follow-up scenarios as well as sail-propelled head-on retrograde kinetic impactors (RKI) for mitigation. Other mission types such as the Displaced L1 (DL1) space weather advance warning and monitoring or Solar Polar Orbiter (SPO) types demonstrate the capability of near-term solar sails to achieve asteroid rendezvous in any kind of orbit, from Earth-coorbital to extremely inclined and even retrograde orbits. Some of these mission types such as SPO, (M)NR and RKI include separable payloads. For one-way access to the asteroid surface, nanolanders like MASCOT are an ideal match for solar sails in micro-spacecraft format, i.e. in launch configurations compatible with ESPA and ASAP secondary payload platforms. Larger landers similar to the JAXA-DLR study of a Jupiter Trojan asteroid lander for the OKEANOS mission can shuttle from the sail to the asteroids visited and enable multiple NEA sample-return missions. The high impact velocities and re-try capability achieved by the RKI mission type on a final orbit identical to the target asteroid's but retrograde to its motion enables small spacecraft size impactors to carry sufficient kinetic energy for deflection.},
  language  = {en}
}
@inproceedings{FingerdeVriesVosetal.2020,
  author    = {Finger, Felix and de Vries, Reynard and Vos, Roelof and Braun, Carsten and Bil, Cees},
  title     = {A comparison of hybrid-electric aircraft sizing methods},
  series = {AIAA Scitech 2020 Forum},
  booktitle = {AIAA Scitech 2020 Forum},
  doi       = {10.2514/6.2020-1006},
  pages     = {31 Seiten},
  year      = {2020},
  language  = {en}
}
@article{SmithKotliarLammertynetal.2020,
  author    = {Smith, Wayne and Kotliar, Konstantin and Lammertyn, Leandi and Ramoshaba, Nthai E. and Vilser, Walthard and Huisman, Hugo W. and Schutte, Aletta E.},
  title     = {Retinal vessel caliber and caliber responses in true normotensive black and white adults: The African-PREDICT study},
  series = {Microvascular Research},
  volume    = {128},
  journal   = {Microvascular Research},
  number    = {Article 103937},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {0026-2862},
  doi       = {10.1016/j.mvr.2019.103937},
  year      = {2020},
  abstract  = {Purpose Globally, a detrimental shift in cardiovascular disease risk factors and a higher mortality level are reported in some black populations. The retinal microvasculature provides early insight into the pathogenesis of systemic vascular diseases, but it is unclear whether retinal vessel calibers and acute retinal vessel functional responses differ between young healthy black and white adults. Methods We included 112 black and 143 white healthy normotensive adults (20-30 years). Retinal vessel calibers (central retinal artery and vein equivalent (CRAE and CRVE)) were calculated from retinal images and vessel caliber responses to flicker light induced provocation (FLIP) were determined. Additionally, ambulatory blood pressure (BP), anthropometry and blood samples were collected. Results The groups displayed similar 24 h BP profiles and anthropometry (all p > .24). Black participants demonstrated a smaller CRAE (158 ± 11 vs. 164 ± 11 MU, p < .001) compared to the white group, whereas CRVE was similar (p = .57). In response to FLIP, artery maximal dilation was greater in the black vs. white group (5.6 ± 2.1 vs. 3.3 ± 1.8\%; p < .001). Conclusions Already at a young age, healthy black adults showed narrower retinal arteries relative to the white population. Follow-up studies are underway to show if this will be related to increased risk for hypertension development. The reason for the larger vessel dilation responses to FLIP in the black population is unclear and warrants further investigation.},
  language  = {en}
}
@inproceedings{KreyerMuellerEsch2020,
  author    = {Kreyer, J{\"o}rg and M{\"u}ller, Marvin and Esch, Thomas},
  title     = {A Map-Based Model for the Determination of Fuel Consumption for Internal Combustion Engines as a Function of Flight Altitude},
  series = {Deutscher Luft- und Raumfahrtkongress 2019, „Luft- und Raumfahrt - technologische Br{\"u}cke in die Zukunft", Darmstadt, 30. September bis 2. Oktober 2019},
  booktitle = {Deutscher Luft- und Raumfahrtkongress 2019, „Luft- und Raumfahrt - technologische Br{\"u}cke in die Zukunft", Darmstadt, 30. September bis 2. Oktober 2019},
  publisher = {Deutsche Gesellschaft f{\"u}r Luft- und Raumfahrt - Lilienthal-Oberth e.V},
  address   = {Bonn},
  doi       = {10.25967/490162},
  pages     = {13 Seiten},
  year      = {2020},
  language  = {en}
}
@inproceedings{FingerGoettenBraunetal.2019,
  author    = {Finger, Felix and G{\"o}tten, Falk and Braun, Carsten and Bil, Cees},
  title     = {Cost Estimation Methods for Hybrid-Electric General Aviation Aircraft},
  series = {Asia Pacific International Symposium on Aerospace Technology. APISAT 2019},
  booktitle = {Asia Pacific International Symposium on Aerospace Technology. APISAT 2019},
  pages     = {1 -- 13},
  year      = {2019},
  language  = {en}
}
@inproceedings{FingerBraunBil2020,
  author    = {Finger, Felix and Braun, Carsten and Bil, Cees},
  title     = {Comparative assessment of parallel-hybrid-electric propulsion systems for four different aircraft},
  series = {AIAA SciTech Forum 2020, 06.01.2020 - 10.01.2020, Orlando},
  booktitle = {AIAA SciTech Forum 2020, 06.01.2020 - 10.01.2020, Orlando},
  doi       = {10.2514/6.2020-1502},
  pages     = {15 Seiten},
  year      = {2020},
  language  = {en}
}
@inproceedings{GoettenFingerMarinoetal.2019,
  author    = {G{\"o}tten, Falk and Finger, Felix and Marino, Matthew and Bil, Cees and Havermann, Marc and Braun, Carsten},
  title     = {A review of guidelines and best practices for subsonic aerodynamic simulations using RANS CFD},
  series = {Asia-Pacific International Symposium on Aerospace Technology (APISAT), At Gold Coast, Australia, 04. - 06. Dezember 2019},
  booktitle = {Asia-Pacific International Symposium on Aerospace Technology (APISAT), At Gold Coast, Australia, 04. - 06. Dezember 2019},
  isbn      = {978-1-925627-40-4},
  pages     = {19 Seiten},
  year      = {2019},
  language  = {de}
}
@article{FingerBraunBil2020,
  author    = {Finger, Felix and Braun, Carsten and Bil, Cees},
  title     = {Impact of Battery Performance on the Initial Sizing of Hybrid-Electric General Aviation Aircraft},
  series = {Journal of Aerospace Engineering},
  volume    = {33},
  journal   = {Journal of Aerospace Engineering},
  number    = {3},
  publisher = {ASCE},
  address   = {Reston, Va.},
  issn      = {1943-5525},
  doi       = {10.1061/(ASCE)AS.1943-5525.0001113},
  year      = {2020},
  abstract  = {Studies suggest that hybrid-electric aircraft have the potential to generate fewer emissions and be inherently quieter when compared to conventional aircraft. By operating combustion engines together with an electric propulsion system, synergistic benefits can be obtained. However, the performance of hybrid-electric aircraft is still constrained by a battery's energy density and discharge rate. In this paper, the influence of battery performance on the gross mass for a four-seat general aviation aircraft with a hybrid-electric propulsion system is analyzed. For this design study, a high-level approach is chosen, using an innovative initial sizing methodology to determine the minimum required aircraft mass for a specific set of requirements and constraints. Only the peak-load shaving operational strategy is analyzed. Both parallel- and serial-hybrid propulsion configurations are considered for two different missions. The specific energy of the battery pack is varied from 200 to 1,000 W⋅h/kg, while the discharge time, and thus the normalized discharge rating (C-rating), is varied between 30 min (2C discharge rate) and 2 min (30C discharge rate). With the peak-load shaving operating strategy, it is desirable for hybrid-electric aircraft to use a light, low capacity battery system to boost performance. For this case, the battery's specific power rating proved to be of much higher importance than for full electric designs, which have high capacity batteries. Discharge ratings of 20C allow a significant take-off mass reduction aircraft. The design point moves to higher wing loadings and higher levels of hybridization if batteries with advanced technology are used.},
  language  = {en}
}
@inproceedings{FingerKhalsaKreyeretal.2019,
  author    = {Finger, Felix and Khalsa, R. and Kreyer, J{\"o}rg and Mayntz, Joscha and Braun, Carsten and Dahmann, Peter and Esch, Thomas and Kemper, Hans and Schmitz, O. and Bragard, Michael},
  title     = {An approach to propulsion system modelling for the conceptual design of hybrid-electric general aviation aircraft},
  series = {Deutscher Luft- und Raumfahrtkongress 2019, 30.9.-2.10.2019, Darmstadt},
  booktitle = {Deutscher Luft- und Raumfahrtkongress 2019, 30.9.-2.10.2019, Darmstadt},
  pages     = {15 Seiten},
  year      = {2019},
  abstract  = {In this paper, an approach to propulsion system modelling for hybrid-electric general aviation aircraft is presented. Because the focus is on general aviation aircraft, only combinations of electric motors and reciprocating combustion engines are explored. Gas turbine hybrids will not be considered. The level of the component's models is appropriate for the conceptual design stage. They are simple and adaptable, so that a wide range of designs with morphologically different propulsive system architectures can be quickly compared. Modelling strategies for both mass and efficiency of each part of the propulsion system (engine, motor, battery and propeller) will be presented.},
  language  = {en}
}
@inproceedings{QuitterMarinoBauschat2019,
  author    = {Quitter, Julius and Marino, Matthew and Bauschat, J.-Michael},
  title     = {Highly Non-Planar Aircraft Configurations: Estimation of Flight Mechanical Derivatives Using Low-Order Methods},
  series = {Deutscher Luft- und Raumfahrtkongress 2019, DLRK 2019. Darmstadt, Germany},
  booktitle = {Deutscher Luft- und Raumfahrtkongress 2019, DLRK 2019. Darmstadt, Germany},
  pages     = {10 Seiten},
  year      = {2019},
  language  = {en}
}
@inproceedings{FunkeBeckmannAbanteriba2017,
  author    = {Funke, Harald and Beckmann, Nils and Abanteriba, Sylvester},
  title     = {A comparison of complex chemistry mechanisms for hydrogen methane blends based on the Sandia / Sydney Bluff-Body Flame HM1},
  series = {Proceedings of the Eleventh Asia-Pacific Conference on Combustion (ASPACC 2017), New South Wales, Australia, 10-14 December 2017},
  booktitle = {Proceedings of the Eleventh Asia-Pacific Conference on Combustion (ASPACC 2017), New South Wales, Australia, 10-14 December 2017},
  isbn      = {978-1-5108-5646-2},
  pages     = {262 -- 265},
  year      = {2017},
  language  = {en}
}
@inproceedings{FunkeBeckmannAbanteriba2019,
  author    = {Funke, Harald and Beckmann, Nils and Abanteriba, Sylvester},
  title     = {Development and Testing of a FuelFlex Dry-Low-NOx Micromix Combustor for Industrial Gas Turbine Applications With Variable Hydrogen Methane Mixtures},
  series = {ASME Turbo Expo 2019: Turbomachinery Technical Conference and Exposition. June 17-21, 2019 Phoenix, Arizona, USA. Volume 4A: Combustion, Fuels, and Emissions},
  booktitle = {ASME Turbo Expo 2019: Turbomachinery Technical Conference and Exposition. June 17-21, 2019 Phoenix, Arizona, USA. Volume 4A: Combustion, Fuels, and Emissions},
  isbn      = {978-0-7918-5861-5},
  doi       = {10.1115/GT2019-90095},
  pages     = {11 Seiten},
  year      = {2019},
  language  = {en}
}
@inproceedings{HorikawaOkadaUtoetal.2019,
  author    = {Horikawa, Atsushi and Okada, Kunio and Uto, Takahiro and Uchiyama, Yuta and Wirsum, Manfred and Funke, Harald and Kusterer, Karsten},
  title     = {Application of Low NOx Micro-mix Hydrogen Combustion to 2MW Class Industrial Gas Turbine Combustor},
  series = {Proceedings of International Gas Turbine Congress 2019 Tokyo, November 17-22, 2019, Tokyo, Japan},
  booktitle = {Proceedings of International Gas Turbine Congress 2019 Tokyo, November 17-22, 2019, Tokyo, Japan},
  isbn      = {978-4-89111-010-9},
  pages     = {1 -- 6},
  year      = {2019},
  language  = {en}
}
@inproceedings{FunkeBeckmann2019,
  author    = {Funke, Harald and Beckmann, Nils},
  title     = {Flexible Fuel Operation of a Dry-Low-Nox Micromix Combustor with Variable Hydrogen Methane Mixtures},
  series = {Proceedings of International Gas Turbine Congress 2019 Tokyo, November 17-22, 2019, Tokyo, Japan},
  booktitle = {Proceedings of International Gas Turbine Congress 2019 Tokyo, November 17-22, 2019, Tokyo, Japan},
  isbn      = {978-4-89111-010-9},
  year      = {2019},
  language  = {en}
}
@inproceedings{StrieganStruthDickhoffetal.2019,
  author    = {Striegan, Constantin J. D. and Struth, Benjamin and Dickhoff, Jens and Kusterer, Karsten and Funke, Harald and Bohn, Dieter},
  title     = {Numerical Simulations of the Micromix DLN Hydrogen Combustion Technology with LES and Comparison to Results of RANS and Experimental Data},
  series = {Proceedings of International Gas Turbine Congress 2019 Tokyo, November 17-22, 2019, Tokyo, Japan.},
  booktitle = {Proceedings of International Gas Turbine Congress 2019 Tokyo, November 17-22, 2019, Tokyo, Japan.},
  isbn      = {978-4-89111-010-9},
  pages     = {1 -- 9},
  year      = {2019},
  language  = {en}
}