@article{MossetDevroedeKriegueretal.2006,
  author    = {Mosset, J.-B. and Devroede, O. and Krieguer, M. and Rey, M. and Vieira, J.-M. and Jung, J. H. and Kuntner, C. and Streun, M. and Ziemons, Karl and Auffray, E. and Sempere-Roldan, P. and Lecoq, P. and Bruyndonckx, P. and Loude, J.-F. and Tavernier, S. and Morcel, C.},
  title     = {Development of an optimized LSO/LuYAP phoswich detector head for the Lausanne ClearPET demonstrator},
  series = {IEEE Transactions on Nuclear Science},
  volume    = {53},
  journal   = {IEEE Transactions on Nuclear Science},
  number    = {1},
  isbn      = {0018-9499},
  pages     = {25 -- 29},
  year      = {2006},
  abstract  = {This paper describes the LSO/LuYAP phoswich detector head developed for the ClearPET small animal PET scanner demonstrator that is under construction in Lausanne within the Crystal Clear Collaboration. The detector head consists of a dual layer of 8×8 LSO and LuYAP crystal arrays coupled to a multi-anode photomultiplier tube (Hamamatsu R7600-M64). Equalistion of the LSO/LuYAP light collection is obtained through partial attenuation of the LSO scintillation light using a thin aluminum deposit of 20-35 nm on LSO and appropriate temperature regulation of the phoswich head between 30°C to 60°C. At 511keV, typical FWHM energy resolutions of the pixels of a phoswich head amounts to (28±2)\% for LSO and (25±2)\% for LuYAP. The LSO versus LuYAP crystal identification efficiency is better than 98\%. Six detector modules have been mounted on a rotating gantry. Axial and tangential spatial resolutions were measured up to 4 cm from the scanner axis and compared to Monte Carlo simulations using GATE. FWHM spatial resolution ranges from 1.3 mm on axis to 2.6 mm at 4 cm from the axis.},
  language  = {en}
}
@inproceedings{UibelBlass2006,
  author    = {Uibel, Thomas and Blaß, Hans Joachim},
  title     = {Load Carrying Capacity of Joints with Dowel Type Fasteners in Solid Wood Panels},
  series = {Proceedings. CIB-W18 Meeting 2006, Florence, Italy 2006},
  booktitle = {Proceedings. CIB-W18 Meeting 2006, Florence, Italy 2006},
  issn      = {0945-6996},
  pages     = {1 -- 10},
  year      = {2006},
  language  = {en}
}
@inproceedings{ReimerBraunBallmann2006,
  author    = {Reimer, Lars and Braun, Carsten and Ballmann, Josef},
  title     = {Analysis of the static and dynamic aero-structural response of an elastic swept wing model by direct aeroelastic simulation},
  series = {ICAS 2006 proceedings : 25th Congress of the International Council of the Aeronautical Sciences ; Hamburg, Germany, 3 - 8 September, 2006 : 25th International Congress of Aeronautical Sciences},
  booktitle = {ICAS 2006 proceedings : 25th Congress of the International Council of the Aeronautical Sciences ; Hamburg, Germany, 3 - 8 September, 2006 : 25th International Congress of Aeronautical Sciences},
  publisher = {Optimage},
  address   = {Edinburgh},
  organization    = {International Council of the Aeronautical Sciences (ICAS)},
  isbn      = {0-9533991-7-6},
  pages     = {Paper No. 2006-10.3.3},
  year      = {2006},
  language  = {en}
}
@inproceedings{BallmannDafnisBraunetal.2006,
  author    = {Ballmann, Josef and Dafnis, Athanasios and Braun, Carsten and Korsch, Helge and Reimerdes, Hans-G{\"u}nther and Braun, Carsten and Ballmann, Josef},
  title     = {The HIRENASD project: High Reynolds number aerostructural dynamics experiments in the European Transonic Wind Tunnel (ETW)},
  series = {ICAS 2006 proceedings : 25th Congress of the International Council of the Aeronautical Sciences ; Hamburg, Germany, 3 - 8 September, 2006 : 25th International Congress of Aeronautical Sciences},
  booktitle = {ICAS 2006 proceedings : 25th Congress of the International Council of the Aeronautical Sciences ; Hamburg, Germany, 3 - 8 September, 2006 : 25th International Congress of Aeronautical Sciences},
  publisher = {Optimage},
  address   = {Edinburgh},
  organization    = {International Council of the Aeronautical Sciences (ICAS)},
  isbn      = {0-9533991-7-6},
  pages     = {Paper No. 2006-5.11.2},
  year      = {2006},
  language  = {en}
}
@inproceedings{KorschDafnisReimerdesetal.2006,
  author    = {Korsch, Helge and Dafnis, Athanasios and Reimerdes, Hans-G{\"u}nther and Braun, Carsten and Ballmann, Josef},
  title     = {Dynamic qualification of the HIRENASD elastic wing model},
  series = {Motto: Luft- und Raumfahrt: Lehre, Forschung, Industrie - gemeinsam innovativ. Deutscher Luft- und Raumfahrtkongress 2006 : Braunschweig, 06. bis 09. November 2006. Jahrbuch / Deutsche Gesellschaft f{\"u}r Luft- und Raumfahrt. 2006},
  booktitle = {Motto: Luft- und Raumfahrt: Lehre, Forschung, Industrie - gemeinsam innovativ. Deutscher Luft- und Raumfahrtkongress 2006 : Braunschweig, 06. bis 09. November 2006. Jahrbuch / Deutsche Gesellschaft f{\"u}r Luft- und Raumfahrt. 2006},
  publisher = {Dt. Gesellschaft f{\"u}r Luft- und Raumfahrt - Lilienthal-Oberth (DGLR)},
  address   = {Bonn},
  pages     = {1441 -- 1450},
  year      = {2006},
  language  = {en}
}
@inproceedings{RaupachOrlowskyBuettneretal.2006,
  author    = {Raupach, Michael and Orlowsky, Jeannette and B{\"u}ttner, T. and Dilthey, Ulrich and Schleser, Markus},
  title     = {Epoxy-impregnated textiles in concrete - load bearing capacity and durability},
  series = {Textile reinforced concrete : proceedings of the 1. International RILEM Conference, held at the RWTH Aachen, September 6/7, 2006. (RILEM proceedings ; 50)},
  booktitle = {Textile reinforced concrete : proceedings of the 1. International RILEM Conference, held at the RWTH Aachen, September 6/7, 2006. (RILEM proceedings ; 50)},
  editor    = {Hegger, Josef},
  publisher = {RILEM Publ.},
  address   = {Bagneux},
  organization    = {International Conference on Textile Reinforced Concrete <1, 2006, Aachen>},
  isbn      = {2-912143-97-7},
  pages     = {77 -- 88},
  year      = {2006},
  language  = {en}
}
@inproceedings{PakPiegelerFeldmannetal.2006,
  author    = {Pak, Daniel and Piegeler, D. and Feldmann, Markus and Schleser, Markus and Dilthey, Ulrich},
  title     = {Hybrid joints of textile reinforced concrete parts - designed for assembly},
  series = {Textile reinforced concrete : proceedings of the 1. International RILEM Conference, held at the RWTH Aachen, September 6/7, 2006. (RILEM proceedings ; 50)},
  booktitle = {Textile reinforced concrete : proceedings of the 1. International RILEM Conference, held at the RWTH Aachen, September 6/7, 2006. (RILEM proceedings ; 50)},
  editor    = {Hegger, Josef},
  publisher = {RILEM Publ.},
  address   = {Bagneux},
  organization    = {International Conference on Textile Reinforced Concrete <1, 2006, Aachen>},
  isbn      = {2-912143-97-7},
  pages     = {181 -- 190},
  year      = {2006},
  language  = {en}
}
@inproceedings{DiltheySchleser2006,
  author    = {Dilthey, Ulrich and Schleser, Markus},
  title     = {Composite improvement of textile reinforced concrete by polymeric impregnation of the textiles},
  series = {International Symposium Polymers in Concrete : proceedings of ISPIC 2006, 2-4 April 2006 - University of Minho - Guimar{\~a}es, Portugal},
  booktitle = {International Symposium Polymers in Concrete : proceedings of ISPIC 2006, 2-4 April 2006 - University of Minho - Guimar{\~a}es, Portugal},
  editor    = {Barroso de Aguiar, Jose and Jalali, Said and Camoes, Aires and Ferrera, Rui Miguel},
  publisher = {Universidade do Minho, Departamento de Engenharia Civil},
  address   = {Guimar{\~a}es},
  organization    = {International Symposium in Concrete <2006, Guimar{\~a}es)},
  isbn      = {972-99179-1-4},
  pages     = {185 -- 192},
  year      = {2006},
  language  = {en}
}
@inproceedings{FendHoffschmidtReutteretal.2006,
  author    = {Fend, Thomas and Hoffschmidt, Bernhard and Reutter, Oliver and Sauerhering, J{\"o}rg and Pitz-Paal, Robert},
  title     = {Gas flow in hot porous materials: the solar air receiver and spin-off applications},
  series = {Proceedings of the 4th Nanochannels, Microchannels and Minichannels - 2006 : presented at 4th Nanochannels, Microchannels and Minichannels, June 19 - 21, 2006, Limerick, Ireland},
  booktitle = {Proceedings of the 4th Nanochannels, Microchannels and Minichannels - 2006 : presented at 4th Nanochannels, Microchannels and Minichannels, June 19 - 21, 2006, Limerick, Ireland},
  publisher = {ASME},
  address   = {New York, NY},
  organization    = {International Conference on Nanochannels, Microchannels and Minichannels <4, 2006, Limerick>},
  isbn      = {0-7918-4760-8},
  pages     = {507 -- 514},
  year      = {2006},
  language  = {en}
}
@inproceedings{HoffschmidtSchwarzerSpaeteetal.2006,
  author    = {Hoffschmidt, Bernhard and Schwarzer, Klemens and Sp{\"a}te, Frank and K{\"o}tter, Jens and Ebert, Miriam and Sierck, Olaf},
  title     = {Development of a small modular parabolic trough collector},
  series = {13th International Symposium Concentrated Solar Power and Chemical Energy Technologies : SolarPaces : June 20 - 23, 2006, Seville, Spain},
  booktitle = {13th International Symposium Concentrated Solar Power and Chemical Energy Technologies : SolarPaces : June 20 - 23, 2006, Seville, Spain},
  publisher = {SolarPaces},
  address   = {[o.O.]},
  organization    = {International Symposium on Concentrating Solar Power and Chemical Energy Systems <13, 2006, Sevilla>},
  isbn      = {8478345191},
  pages     = {1 CD-ROM},
  year      = {2006},
  language  = {en}
}
@article{SchleserWalkLaufferRaupachetal.2006,
  author    = {Schleser, Markus and Walk-Lauffer, Bernd and Raupach, Michael and Dilthey, Ulrich},
  title     = {Application of polymers for textile-reinforced concrete},
  series = {Journal of materials in civil engineering : properties, applications, durability},
  volume    = {18},
  journal   = {Journal of materials in civil engineering : properties, applications, durability},
  number    = {5},
  issn      = {0899-1561},
  pages     = {670 -- 676},
  year      = {2006},
  language  = {en}
}
@article{FeldmannPakGessleretal.2006,
  author    = {Feldmann, Markus and Pak, Daniel and Geßler, Achim and Dilthey, Ulrich and Schleser, Markus},
  title     = {Bonded connections for textile reinforced concrete structures},
  series = {Cailiao-gongcheng = Journal of materials engineering},
  journal   = {Cailiao-gongcheng = Journal of materials engineering},
  number    = {Special iss.},
  issn      = {1001-4381},
  pages     = {123 -- 127},
  year      = {2006},
  language  = {en}
}
@inproceedings{DiltheySchleserMoelleretal.2006,
  author    = {Dilthey, Ulrich and Schleser, Markus and M{\"o}ller, M. and Weichhold, O.},
  title     = {Application of polymers in textile reinforced concrete : from the interface to construction elements},
  series = {Textile reinforced concrete : proceedings of the 1. International RILEM Conference, held at the RWTH Aachen, September 6/7, 2006. (RILEM proceedings ; 50)},
  booktitle = {Textile reinforced concrete : proceedings of the 1. International RILEM Conference, held at the RWTH Aachen, September 6/7, 2006. (RILEM proceedings ; 50)},
  editor    = {Hegger, Josef},
  publisher = {RILEM Publ.},
  address   = {Bagneux},
  organization    = {International Conference on Textile Reinforced Concrete <1, 2006, Aachen>},
  isbn      = {2-912143-97-7},
  pages     = {55 -- 64},
  year      = {2006},
  language  = {en}
}
@inproceedings{HellmannsBoehmDilger2006,
  author    = {Hellmanns, Mark and B{\"o}hm, Stefan and Dilger, Klaus},
  title     = {Implementation of a velocity controlled manual applicator for adhesives and sealants in the automotive industry in consideration of quality control},
  series = {Proceedings of the 29th annual meeting of the Adhesion Society : 19. - 22.2.2006, Jacksonville, Florida},
  booktitle = {Proceedings of the 29th annual meeting of the Adhesion Society : 19. - 22.2.2006, Jacksonville, Florida},
  publisher = {Adhesion Society},
  address   = {Blacksburg, Va.},
  organization    = {Adhesion Society},
  issn      = {1086-9506},
  pages     = {68 -- 70},
  year      = {2006},
  language  = {en}
}
@article{HellmannsBoehmDilger2006,
  author    = {Hellmanns, Mark and B{\"o}hm, Stefan and Dilger, Klaus},
  title     = {Manual applications of adhesives},
  series = {Journal of adhesion and interface},
  volume    = {Vol. 7},
  journal   = {Journal of adhesion and interface},
  number    = {No. 4},
  pages     = {24 -- 27},
  year      = {2006},
  language  = {en}
}
@inproceedings{HellmannsBoehmDilger2006,
  author    = {Hellmanns, Mark and B{\"o}hm, Stefan and Dilger, Klaus},
  title     = {Progress of the manual application of adhesives},
  series = {Proceedings of the 3rd World Congress on Adhesion and Related Phenomena : WCARP-III, October 15 -18, 2006, Beijing, China},
  booktitle = {Proceedings of the 3rd World Congress on Adhesion and Related Phenomena : WCARP-III, October 15 -18, 2006, Beijing, China},
  publisher = {Beijing Adhesion Society of China},
  address   = {Beijing},
  pages     = {275 -- 277},
  year      = {2006},
  language  = {en}
}
@inproceedings{BoehmHellmannsBackesetal.2006,
  author    = {B{\"o}hm, Stefan and Hellmanns, Mark and Backes, Andreas and Dilger, Klaus},
  title     = {Lock-in thermography based NDT of automotive parts},
  series = {Proceedings of the 3rd World Congress on Adhesion and Related Phenomena : WCARP-III, October 15 -18, 2006, Beijing, China},
  booktitle = {Proceedings of the 3rd World Congress on Adhesion and Related Phenomena : WCARP-III, October 15 -18, 2006, Beijing, China},
  publisher = {Beijing Adhesion Society of China},
  address   = {Beijing},
  pages     = {382 -- 384},
  year      = {2006},
  language  = {en}
}
@article{BoehmHellmannsBackesetal.2006,
  author    = {B{\"o}hm, Stefan and Hellmanns, Mark and Backes, Andreas and Dilger, Klaus},
  title     = {Lock-in thermography based NDT of parts for the automotive industry},
  series = {Journal of adhesion and interface},
  volume    = {Vol. 7},
  journal   = {Journal of adhesion and interface},
  number    = {No. 4},
  pages     = {10 -- 12},
  year      = {2006},
  language  = {en}
}
@techreport{ConanD'HaeyerBeguinetal.2006,
  author    = {Conan, Yulian and D'Haeyer, R. and B{\´e}guin, P. and D{\"o}ring, Bernd and Kuhnhenne, Markus and Bayo, E.},
  title     = {Steel in low-rise building : a symbiosis of cold formed sections and light rolled profiles : final report. Contract-No. 7215-PP/070. EUR 22080 en},
  publisher = {Office for Official Publications of the European Communities},
  address   = {Luxembourg},
  isbn      = {92-79-02082-X},
  pages     = {200 S.},
  year      = {2006},
  language  = {en}
}
@article{HellwigVolkmann2006,
  author    = {Hellwig, Angelika and Volkmann, Lutz},
  title     = {Lower bounds on the vertex-connectivity of digraphs and graphs},
  series = {Information processing letters},
  volume    = {Vol. 99},
  journal   = {Information processing letters},
  number    = {Iss. 2},
  issn      = {1872-6119 (E-Journal); 0020-0190 (Print)},
  pages     = {41 -- 46},
  year      = {2006},
  language  = {en}
}
@article{HellwigVolkmann2006,
  author    = {Hellwig, Angelika and Volkmann, Lutz},
  title     = {On connectivity in graphs with given clique number},
  series = {Journal of graph theory},
  volume    = {Vol. 52},
  journal   = {Journal of graph theory},
  number    = {Iss. 1},
  issn      = {03649024 ; 10970118},
  pages     = {7 -- 14},
  year      = {2006},
  language  = {en}
}
@article{HellwigVolkmann2006,
  author    = {Hellwig, Angelika and Volkmann, Lutz},
  title     = {Some upper bounds for the domination number},
  series = {The journal of combinatorial mathematics and combinatorial computing : JCMCC},
  volume    = {Vol. 57},
  journal   = {The journal of combinatorial mathematics and combinatorial computing : JCMCC},
  issn      = {0835-3026},
  pages     = {187 -- 209},
  year      = {2006},
  language  = {en}
}
@article{VorstFerreinLakemeyer2006,
  author    = {Vorst, Phillip and Ferrein, Alexander and Lakemeyer, Gerhard},
  title     = {AllemaniACs3D team description},
  pages     = {1 -- 6},
  year      = {2006},
  language  = {en}
}
@inproceedings{FerreinLakemeyerSchiffer2006,
  author    = {Ferrein, Alexander and Lakemeyer, Gerhard and Schiffer, Stefan},
  title     = {AllemaniACs@ home 2006 team description},
  pages     = {1 -- 6},
  year      = {2006},
  language  = {en}
}
@misc{Pfaff2006,
  type      = {Master Thesis},
  author    = {Pfaff, Raphael},
  title     = {Modelling of nonlinear systems using piecewise defined models},
  year      = {2006},
  language  = {en}
}
@inproceedings{PfaffVinsonneauBurnham2006,
  author    = {Pfaff, Raphael and Vinsonneau, B. and Burnham, K. J.},
  title     = {Multiple models for nonlinear systems},
  series = {Proceedings / Eigteenth International Conference on Systems Engineering : ICSE 2006 : 5 - 7 September 2006 ; [held at Coventry University, UK]},
  booktitle = {Proceedings / Eigteenth International Conference on Systems Engineering : ICSE 2006 : 5 - 7 September 2006 ; [held at Coventry University, UK]},
  organization    = {International Conference on Systems Engineering <18, 2006, Coventry>},
  isbn      = {1-84600-013-0},
  pages     = {347 -- 352},
  year      = {2006},
  language  = {en}
}
@article{EilmannWeberRiglingetal.2006,
  author    = {Eilmann, Britta and Weber, Pascale and Rigling, Andreas and Eckstein, Dieter},
  title     = {Growth reactions of Pinus sylvestris L. and Quercus pubescens Willd. to drought years at a xeric site in Valais, Switzerland},
  series = {Dendrochronologia},
  volume    = {23},
  journal   = {Dendrochronologia},
  number    = {3},
  issn      = {1612-0051 (Online)},
  doi       = {doi:10.1016/j.dendro.2005.10.002},
  pages     = {121 -- 132},
  year      = {2006},
  language  = {en}
}
@inproceedings{NaetherPoghossianPlatenetal.2006,
  author    = {N{\"a}ther, Niko and Poghossian, Arshak and Platen, J. and Yoshinobu, T. and Koudelka-Hep, M. and Sch{\"o}ning, Michael Josef},
  title     = {Multi-parameter sensing of both physical and (bio-)chemical quantities using the same transducer principle},
  series = {Biochemical sensing utilisation of micro- and nanotechnologies : Warsaw, [23rd - 26th] November 2005 / ed. by M. Mascini ...},
  booktitle = {Biochemical sensing utilisation of micro- and nanotechnologies : Warsaw, [23rd - 26th] November 2005 / ed. by M. Mascini ...},
  address   = {Warsaw},
  pages     = {172 -- 181},
  year      = {2006},
  language  = {en}
}
@inproceedings{KloockSchubertErmelenkoetal.2006,
  author    = {Kloock, Joachim P. and Schubert, J. and Ermelenko, Y. and Vlasov, Y. G. and Bratov, A. and Sch{\"o}ning, Michael Josef},
  title     = {Thin-film sensors with chalcogenide glass materials - a general survey},
  series = {Biochemical sensing utilisation of micro- and nanotechnologies : Warsaw, [23rd - 26th] November 2005 / ed. by M. Mascini ...},
  booktitle = {Biochemical sensing utilisation of micro- and nanotechnologies : Warsaw, [23rd - 26th] November 2005 / ed. by M. Mascini ...},
  address   = {Warsaw},
  pages     = {92 -- 97},
  year      = {2006},
  language  = {en}
}
@inproceedings{SchoeningAbouzarWagneretal.2006,
  author    = {Sch{\"o}ning, Michael Josef and Abouzar, Maryam H. and Wagner, Torsten and N{\"a}ther, Niko and Rolka, David and Yoshinobu, Tatsuo and Kloock, Joachim P. and Turek, Monika and Ingebrandt, Sven and Poghossian, Arshak},
  title     = {A semiconductor-based field-effect platform for (bio-)chemical and physical sensors: From capacitive EIS sensors and LAPS over ISFETs to nano-scale devices},
  series = {MRS Proceedings},
  booktitle = {MRS Proceedings},
  doi       = {10.1557/PROC-0952-F08-02},
  pages     = {1 -- 9},
  year      = {2006},
  language  = {en}
}
@article{SchoeningPoghossian2006,
  author    = {Sch{\"o}ning, Michael Josef and Poghossian, Arshak},
  title     = {BioFEDs (field-effect devices) : State-of-the-art and new directions},
  series = {Electroanalysis},
  volume    = {18},
  journal   = {Electroanalysis},
  number    = {19-20},
  issn      = {1521-4109},
  doi       = {10.1002/elan.200603609},
  pages     = {1893 -- 1900},
  year      = {2006},
  language  = {en}
}
@inproceedings{PoghossianSchumacherKloocketal.2006,
  author    = {Poghossian, Arshak and Schumacher, Kerstin and Kloock, Joachim P. and Rosenkranz, Christian and Schultze, Joachim W. and M{\"u}ller-Veggian, Mattea and Sch{\"o}ning, Michael Josef},
  title     = {Functional testing and characterisation of ISFETs on wafer level by means of a micro-droplet cell},
  url       = {http://nbn-resolving.de/urn:nbn:de:hbz:a96-opus-1259},
  year      = {2006},
  abstract  = {A wafer-level functionality testing and characterisation system for ISFETs (ionsensitive field-effect transistor) is realised by means of integration of a specifically designed capillary electrochemical micro-droplet cell into a commercial wafer prober-station. The developed system allows the identification and selection of "good" ISFETs at the earliest stage and to avoid expensive bonding, encapsulation and packaging processes for nonfunctioning ISFETs and thus, to decrease costs, which are wasted for bad dies. The developed system is also feasible for wafer-level characterisation of ISFETs in terms of sensitivity, hysteresis and response time. Additionally, the system might be also utilised for wafer-level testing of further electrochemical sensors.},
  subject      = {Biosensor},
  language  = {en}
}
@inproceedings{WagnerSchoening2006,
  author    = {Wagner, Torsten and Sch{\"o}ning, Michael Josef},
  title     = {Preface of the Special Issue of I3S 2005 in J{\"u}lich (Germany)},
  url       = {http://nbn-resolving.de/urn:nbn:de:hbz:a96-opus-1365},
  year      = {2006},
  abstract  = {International Symposium on Sensor Science, I3S 2005 <3; 2005; Juelich, Germany> In: Sensors 2006, 6, 260-261 ISSN 1424-8220},
  subject      = {Biosensor},
  language  = {en}
}
@inproceedings{FredebeulKrein2006,
  author    = {Fredebeul-Krein, Markus},
  title     = {Developing competitive broadband markets: Lessons learnt from German and European regulatory approaches on broad-band access},
  year      = {2006},
  abstract  = {A key feature of future broadband markets will be diversity of access technologies, meaning that numerous technologies will be exploited for broadband communication. Various factors will affect the success of these future broadband markets, the regulatory policy being one amongst others. So far, a coherent regulatory approach does not exist as to broadband markets. First results of policies so far suggest that less sector-specific regulation is likely to occur. Instead, regulators must ensure that access to networks and services of potentially dominant providers in a relevant broadband market will satisfy requirements for openness and non-discrimination. In this environment the future challenge of regulationg broadband markets will be to set the right incentives for investment into new infrastructures. This paper examines whether there is a need for the regulation of future broadband access markets an if yes, what is the appropriate regulatory tool to do so. Thereby the focus is on the analysis of European broadband markets and the regulatory approaches applied. The first section provides a description of the characteristics of future broadband markets. The second section discusses possible bottlenecks on broadband markets an their regulatory implications. The third section will examine regulatory issues concerning access to broadband networks in more detail. This will be done by comparing the regulatory approaches of European countries and the results in terms of bradband penetration. The final section will give key recommendations for a regulatory strategy on brandband access markets.},
  subject      = {Telekommunikationsmarkt},
  language  = {en}
}
@inproceedings{MertenConradKaemperetal.2006,
  author    = {Merten, Sabine and Conrad, Thorsten and K{\"a}mper, Klaus-Peter and Picard, Antoni and Sch{\"u}tze, Andreas},
  title     = {Virtual Technology Labs - an efficient tool for the preparation of hands-on-MEMS-courses in training foundries},
  year      = {2006},
  abstract  = {Hands-on-training in high technology areas is usually limited due to the high cost for lab infrastructure and equipment. One specific example is the field of MEMS, where investment and upkeep of clean rooms with microtechnology equipment is either financed by production or R\&D projects greatly reducing the availability for education purposes. For efficient hands-on-courses a MEMS training foundry, currently used jointly by six higher education institutions, was established at FH Kaiserslautern. In a typical one week course, students manufacture a micromachined pressure sensor including all lithography, thin film and packaging steps. This compact and yet complete program is only possible because participants learn to use the different complex machines in advance via a Virtual Training Lab (VTL). In this paper we present the concept of the MEMS training foundry and the VTL preparation together with results from a scientific evaluation of the VTL over the last three years.},
  subject      = {Virtuelles Laboratorium},
  language  = {en}
}
@misc{Staat2006,
  author    = {Staat, Manfred},
  title     = {Engineering Mechanics. Lecture Notes. 2nd edition, translation of the 3rd corrected and extended German edition of "Technische Mechanik"},
  year      = {2006},
  abstract  = {English translation of the corrected lectures notes of Sebastian Kr{\"a}mer. Contents 0 Introduction to Mechanics 1 Statics of Rigid Bodies 2 Elastostatics (Strength of Materials) 3 Kinematics 4 Kinetics Literature},
  subject      = {Technische Mechanik},
  language  = {en}
}
@misc{StaatBarry2006,
  author    = {Staat, Manfred and Barry, Steve},
  title     = {Continuum Mechanics with an Introduction to the Finite Element Method / Steve Barry; Manfred Staat. With extensions by Manfred Staat.},
  year      = {2006},
  abstract  = {Contents: 1 Introduction 2 One Dimensional Continuum Mechanics 3 Tensors 4 Three Dimensional Stress and Strain 5 Conservation Laws 6 Contiunuum Modelling 7 Plain Problems 8 Questions 9 Reference Information},
  subject      = {Technische Mechanik},
  language  = {en}
}
@inproceedings{Gebhardt2006,
  author    = {Gebhardt, Andreas},
  title     = {Technology Diffusion through a Multi-Level Technology Transfer Infrastructure. Contribution to the 1st. All Africa Technology Diffusion Conference Boksburg, South Africa June 12th - 14th 2006},
  year      = {2006},
  abstract  = {Table of contents 1. Introduction 2. Multi-level Technology Transfer Infrastructure 2.1 Level 1: University Education - Encourage the Idea of becoming an Entrepreneur 2.2 Level 2: Post Graduate Education - Improve your skills and focus it on a product family. 2.3 Level 3: Birth of a Company - Focus your skills on a product and a market segment. 2.4 Level 4: Ready to stand alone - Set up your own business 2.5 Level 5: Grow to be Strong - Develop your business 2.6 Level 6: Competitive and independent - Stay innovative. 3. Samples 3.1 Sample 1: Laser Processing and Consulting Centre, LBBZ 3.2 Sample 2: Prototyping Centre, CP 4. Funding - Waste money or even lost Money? 5. Conclusion},
  subject      = {Technologietransfer},
  language  = {en}
}
@article{Gebhardt2006,
  author    = {Gebhardt, Andreas},
  title     = {Generative Manufacturing of Ceramic Parts "Vision Rapid Prototyping"},
  year      = {2006},
  abstract  = {Table of Contents Introduction 1. Generative Manufacturing Processes 2. Classification of Generative Manufacturing Processes 3. Application of Generative Processes on the Fabrication of Ceramic Parts 3.1 Extrusion 3.2 3D-Printing 3.3 Sintering - Laser Sintering 3.4 Layer-Laminate Processes 3.5 Stereolithography (sometimes written: Stereo Lithography) 4. Layer Milling 5. Conclusion - Vision},
  subject      = {Rapid prototyping},
  language  = {en}
}
@inproceedings{SrivastavaSinghDhandetal.2006,
  author    = {Srivastava, Alok and Singh, Virendra and Dhand, Chetna and Kaur, Manindar and Singh, Tejvir and Witte, Katrin and Scherer, Ulrich W.},
  title     = {Study of swift heavy ion modified conduction polymer composites for application as gas sensor},
  url       = {http://nbn-resolving.de/urn:nbn:de:hbz:a96-opus-1345},
  year      = {2006},
  abstract  = {A polyaniline-based conducting composite was prepared by oxidative polymerisation of aniline in a polyvinylchloride (PVC) matrix. The coherent free standing thin films of the composite were prepared by a solution casting method. The polyvinyl chloride-polyaniline composites exposed to 120 MeV ions of silicon with total ion fluence ranging from 1011 to 1013 ions/cm2, were observed to be more sensitive towards ammonia gas than the unirradiated composite. The response time of the irradiated composites was observed to be comparably shorter. We report for the first time the application of swift heavy ion modified insulating polymer conducting polymer (IPCP) composites for sensing of ammonia gas.},
  subject      = {Biosensor},
  language  = {en}
}
@inproceedings{ChaiybounTrauteKiesewetteretal.2006,
  author    = {Chaiyboun, Ali and Traute, R{\"u}diger and Kiesewetter, Olaf and Ahlers, Simon and M{\"u}ller, Gerhard and Doll, Theodor},
  title     = {Modular analytical multicomponent analysis in gas sensor arrays},
  url       = {http://nbn-resolving.de/urn:nbn:de:hbz:a96-opus-1358},
  year      = {2006},
  abstract  = {A multi-sensor system is a chemical sensor system which quantitatively and qualitatively records gases with a combination of cross-sensitive gas sensor arrays and pattern recognition software. This paper addresses the issue of data analysis for identification of gases in a gas sensor array. We introduce a software tool for gas sensor array configuration and simulation. It concerns thereby about a modular software package for the acquisition of data of different sensors. A signal evaluation algorithm referred to as matrix method was used specifically for the software tool. This matrix method computes the gas concentrations from the signals of a sensor array. The software tool was used for the simulation of an array of five sensors to determine gas concentration of CH4, NH3, H2, CO and C2H5OH. The results of the present simulated sensor array indicate that the software tool is capable of the following: (a) identify a gas independently of its concentration; (b) estimate the concentration of the gas, even if the system was not previously exposed to this concentration; (c) tell when a gas concentration exceeds a certain value. A gas sensor data base was build for the configuration of the software. With the data base one can create, generate and manage scenarios and source files for the simulation. With the gas sensor data base and the simulation software an on-line Web-based version was developed, with which the user can configure and simulate sensor arrays on-line.},
  subject      = {Biosensor},
  language  = {en}
}
@inproceedings{SakthivelWeppner2006,
  author    = {Sakthivel, Mariappan and Weppner, Werner},
  title     = {Response behaviour of a hydrogen sensor based on ionic conducting polymer-metal interfaces prepared by the chemical reduction method},
  url       = {http://nbn-resolving.de/urn:nbn:de:hbz:a96-opus-1399},
  year      = {2006},
  abstract  = {A solid-state amperometric hydrogen sensor based on a protonated Nafion membrane and catalytic active electrode operating at room temperature was fabricated and tested. Ionic conducting polymer-metal electrode interfaces were prepared chemically by using the impregnation-reduction method. The polymer membrane was impregnated with tetra-ammine platinum chloride hydrate and the metal ions were subsequently reduced by using either sodium tetrahydroborate or potassium tetrahydroborate. The hydrogen sensing characteristics with air as reference gas is reported. The sensors were capable of detecting hydrogen concentrations from 10 ppm to 10\% in nitrogen. The response time was in the range of 10-30 s and a stable linear current output was observed. The thin Pt films were characterized by XRD, Infrared Spectroscopy, Optical Microscopy, Atomic Force Microscopy, Scanning Electron Microscopy and EDAX.},
  subject      = {Biosensor},
  language  = {en}
}
@inproceedings{KoplinSiemonsOcenValentinetal.2006,
  author    = {Koplin, Tobias J. and Siemons, Maike and Oc{\´e}n-Val{\´e}ntin, C{\´e}sar and Sanders, Daniel and Simon, Ulrich},
  title     = {Workflow for high throughput screening of gas sensing materials},
  url       = {http://nbn-resolving.de/urn:nbn:de:hbz:a96-opus-1407},
  year      = {2006},
  abstract  = {The workflow of a high throughput screening setup for the rapid identification of new and improved sensor materials is presented. The polyol method was applied to prepare nanoparticular metal oxides as base materials, which were functionalised by surface doping. Using multi-electrode substrates and high throughput impedance spectroscopy (HT-IS) a wide range of materials could be screened in a short time. Applying HT-IS in search of new selective gas sensing materials a NO2-tolerant NO sensing material with reduced sensitivities towards other test gases was identified based on iridium doped zinc oxide. Analogous behaviour was observed for iridium doped indium oxide.},
  subject      = {Biosensor},
  language  = {en}
}
@inproceedings{NaetherJuarezEmmerichetal.2006,
  author    = {N{\"a}ther, Niko and Ju{\´a}rez, Leon M. and Emmerich, R{\"u}diger and Berger, J{\"o}rg and Friedrich, Peter and Sch{\"o}ning, Michael Josef},
  title     = {Detection of hydrogen peroxide (H2O2) at exposed temperatures for industrial processes},
  url       = {http://nbn-resolving.de/urn:nbn:de:hbz:a96-opus-1418},
  year      = {2006},
  abstract  = {An H2O2 sensor for the application in industrial sterilisation processes has been developed. Therefore, automated sterilisation equipment at laboratory scale has been constructed using parts from industrial sterilisation facilities. In addition, a software tool has been developed for the control of the sterilisation equipment at laboratory scale. First measurements with the developed sensor set-up as part of the sterilisation equipment have been performed and the sensor has been physically characterised by optical microscopy and SEM.},
  subject      = {Biosensor},
  language  = {en}
}
@inproceedings{WagnerKohlFroebaetal.2006,
  author    = {Wagner, Thorsten and Kohl, Claus-Dieter and Fr{\"o}ba, Michael and Tiemann, Michael},
  title     = {Gas sensing properties of ordered mesoporous SnO2},
  url       = {http://nbn-resolving.de/urn:nbn:de:hbz:a96-opus-1422},
  year      = {2006},
  abstract  = {We report on the synthesis and CO gas-sensing properties of mesoporous tin(IV) oxides (SnO2). For the synthesis cetyltrimethylammonium bromide (CTABr) was used as a structure-directing agent; the resulting SnO2 powders were applied as films to commercially available sensor substrates by drop coating. Nitrogen physisorption shows specific surface areas up to 160 m2·g-1 and mean pore diameters of about 4 nm, as verified by TEM. The film conductance was measured in dependence on the CO concentration in humid synthetic air at a constant temperature of 300 °C. The sensors show a high sensitivity at low CO concentrations and turn out to be largely insensitive towards changes in the relative humidity. We compare the materials with commercially available SnO2-based sensors.},
  subject      = {Biosensor},
  language  = {en}
}
@inproceedings{MirmohseniRostamizadeh2006,
  author    = {Mirmohseni, Abdolreza and Rostamizadeh, Kobra},
  title     = {Quartz crystal nanobalance in conjunction with principal component analysis for identification of volatile organic compounds},
  url       = {http://nbn-resolving.de/urn:nbn:de:hbz:a96-opus-1434},
  year      = {2006},
  abstract  = {Quartz crystal nanobalance (QCN) sensors are considered as powerful masssensitive sensors to determine materials in the sub-nanogram level. In this study, a single piezoelectric quartz crystal nanobalance modified with polystyrene was employed to detect benzene, toluene, ethylbenzene and xylene (BTEX compounds). The frequency shift of the QCN sensor was found to be linear against the BTEX compound concentrations in the range about 1-45 mg l-1. The correlation coefficients for benzene, toluene, ethylbenzene, and xylene were 0.991, 0.9977, 0.9946 and 0.9971, respectively. The principal component analysis was also utilized to process the frequency response data of the single piezoelectric crystal at different times, considering to the different adsorption-desorption dynamics of BTEX compounds. Using principal component analysis, it was found that over 90\% of the data variance could still be explained by use of two principal components (PC1 and PC2). Subsequently, the successful identification of benzene and toluene was possible through the principal component analysis of the transient responses of the polystyrene modified QCN sensor. The results showed that the polystyrene-modified QCN had favorable identification and quantification performances for the BTEX compounds.},
  subject      = {Biosensor},
  language  = {en}
}
@inproceedings{KreutzLoergenGraeweetal.2006,
  author    = {Kreutz, Christian and L{\"o}rgen, J{\"u}rgen and Graewe, Boris and Bargon, Joachim and Yoshida, Mayumi and Freso, Zachary M. and Fr{\`e}chet, Jean M. J.},
  title     = {High frequency quartz micro balances: a promising path to enhanced sensitivity of gravimetric sensors},
  url       = {http://nbn-resolving.de/urn:nbn:de:hbz:a96-opus-1445},
  year      = {2006},
  abstract  = {An array of 50 MHz quartz microbalances (QMBs) coated with a dendronized polymer was used to detect small amounts of volatile organic compounds (VOCs) in the gas phase. The results were compared to those obtained with the commonly used 10 MHz QMBs. The 50 MHz QMBs proved to be a powerful tool for the detection of VOCs in the gas phase; therefore, they represent a promising alternative to the much more delicate surface acoustic wave devices (SAWs).},
  subject      = {Biosensor},
  language  = {en}
}
@inproceedings{RabnerShacham2006,
  author    = {Rabner, Arthur and Shacham, Yosi},
  title     = {A concept for a sensitive micro total analysis system for high throughput fluorescence imaging},
  url       = {http://nbn-resolving.de/urn:nbn:de:hbz:a96-opus-1456},
  year      = {2006},
  abstract  = {This paper discusses possible methods for on-chip fluorescent imaging for integrated bio-sensors. The integration of optical and electro-optical accessories, according to suggested methods, can improve the performance of fluorescence imaging. It can boost the signal to background ratio by a few orders of magnitudes in comparison to conventional discrete setups. The methods that are present in this paper are oriented towards building reproducible arrays for high-throughput micro total analysis systems (µTAS). The first method relates to side illumination of the fluorescent material placed into microcompartments of the lab-on-chip. Its significance is in high utilization of excitation energy for low concentration of fluorescent material. The utilization of a transparent µLED chip, for the second method, allows the placement of the excitation light sources on the same optical axis with emission detector, such that the excitation and emission rays are directed controversly. The third method presents a spatial filtering of the excitation background.},
  subject      = {Biosensor},
  language  = {en}
}
@inproceedings{FoersterStockMontanarietal.2006,
  author    = {F{\"o}rster, Arnold and Stock, J{\"u}rgen and Montanari, Simone and Lepsa, Mihail Ion and L{\"u}th, Hans},
  title     = {Fabrication and characterisation of GaAs Gunn Diode Chips for applications at 77 GHz in automotive industry},
  url       = {http://nbn-resolving.de/urn:nbn:de:hbz:a96-opus-1462},
  year      = {2006},
  abstract  = {GaAs-based Gunn diodes with graded AlGaAs hot electron injector heterostructures have been developed under the special needs in automotive applications. The fabrication of the Gunn diode chips was based on total substrate removal and processing of integrated Au heat sinks. Especially, the thermal and RF behavior of the diodes have been analyzed by DC, impedance and S-parameter measurements. The electrical investigations have revealed the functionality of the hot electron injector. An optimized layer structure could fulfill the requirements in adaptive cruise control (ACC) systems at 77 GHz with typical output power between 50 and 90 mW.},
  subject      = {Biosensor},
  language  = {en}
}
@inproceedings{PlatenPoghossianSchoening2006,
  author    = {Platen, Johannes and Poghossian, Arshak and Sch{\"o}ning, Michael Josef},
  title     = {Microstructured Nanostructures - nanostructuring by means of conventional photolithography and layer-expansion technique},
  url       = {http://nbn-resolving.de/urn:nbn:de:hbz:a96-opus-1477},
  year      = {2006},
  abstract  = {A new and simple method for nanostructuring using conventional photolithography and layer expansion or pattern-size reduction technique is presented, which can further be applied for the fabrication of different nanostructures and nano-devices. The method is based on the conversion of a photolithographically patterned metal layer to a metal-oxide mask with improved pattern-size resolution using thermal oxidation. With this technique, the pattern size can be scaled down to several nanometer dimensions. The proposed method is experimentally demonstrated by preparing nanostructures with different configurations and layouts, like circles, rectangles, trapezoids, "fluidic-channel"-, "cantilever"- and meander-type structures.},
  subject      = {Biosensor},
  language  = {en}
}