@article{FingerBraunBil2018,
  author    = {Finger, Felix and Braun, Carsten and Bil, Cees},
  title     = {Impact of electric propulsion technology and mission requirements on the performance of VTOL UAVs},
  series = {CEAS Aeronautical Journal},
  volume    = {10},
  journal   = {CEAS Aeronautical Journal},
  number    = {3},
  publisher = {Springer},
  issn      = {1869-5582 print},
  doi       = {10.1007/s13272-018-0352-x},
  pages     = {843},
  year      = {2018},
  abstract  = {One of the engineering challenges in aviation is the design of transitioning vertical take-off and landing (VTOL) aircraft. Thrust-borne flight implies a higher mass fraction of the propulsion system, as well as much increased energy consumption in the take-off and landing phases. This mass increase is typically higher for aircraft with a separate lift propulsion system than for aircraft that use the cruise propulsion system to support a dedicated lift system. However, for a cost-benefit trade study, it is necessary to quantify the impact the VTOL requirement and propulsion configuration has on aircraft mass and size. For this reason, sizing studies are conducted. This paper explores the impact of considering a supplemental electric propulsion system for achieving hovering flight. Key variables in this study, apart from the lift system configuration, are the rotor disk loading and hover flight time, as well as the electrical systems technology level for both batteries and motors. Payload and endurance are typically used as the measures of merit for unmanned aircraft that carry electro-optical sensors, and therefore the analysis focuses on these particular parameters.},
  language  = {en}
}
@article{BergSchleserDelidovichetal.2018,
  author    = {Berg, Alexander-Karl and Schleser, Markus and Delidovich, Artem and Houben, Alexander},
  title     = {Ultraschallunterst{\"u}tzter Schmelzklebstoffauftrag},
  series = {adh{\"a}sion KLEBEN \& DICHTEN},
  volume    = {Volume 62},
  journal   = {adh{\"a}sion KLEBEN \& DICHTEN},
  number    = {Issue 12},
  publisher = {Springer},
  doi       = {10.1007/s35145-018-0089-z},
  pages     = {32 -- 37},
  year      = {2018},
  language  = {de}
}
@inproceedings{EssingholtMeyerKuhnetal.2018,
  author    = {Essingholt, Felix and Meyer, Frederic and Kuhn, Peter and Schmidt, Philip and Benkner, Thorsten and Grabmaier, Anton},
  title     = {Non-invasive heart beat measurement using microwave resonators},
  series = {Proceedings, Vol. 2, Eurosensors 2018 Conference, Graz, Austria, 9-12 September 2018},
  booktitle = {Proceedings, Vol. 2, Eurosensors 2018 Conference, Graz, Austria, 9-12 September 2018},
  publisher = {MDPI},
  address   = {Basel},
  issn      = {2504-3900},
  doi       = {10.3390/proceedings2131002},
  pages     = {1002},
  year      = {2018},
  language  = {en}
}
@article{EngelHoltmannUlberetal.2018,
  author    = {Engel, Mareike and Holtmann, Dirk and Ulber, Roland and Tippk{\"o}tter, Nils},
  title     = {Increased Biobutanol Production by Mediator-Less Electro-Fermentation},
  series = {Biotechnology Journal},
  journal   = {Biotechnology Journal},
  number    = {Volume 14, Issue 4},
  publisher = {Wiley-VCH},
  issn      = {1860-7314},
  doi       = {10.1002/biot.201800514},
  pages     = {Artikel 1800514},
  year      = {2018},
  abstract  = {A future bio-economy should not only be based on renewable raw materials but also in the raise of carbon yields of existing production routes. Microbial electrochemical technologies are gaining increased attention for this purpose. In this study, the electro-fermentative production of biobutanol with C. acetobutylicum without the use of exogenous mediators is investigated regarding the medium composition and the reactor design. It is shown that the use of an optimized synthetic culture medium allows higher product concentrations, increased biofilm formation, and higher conductivities compared to a synthetic medium supplemented with yeast extract. Moreover, the optimization of the reactor system results in a doubling of the maximum product concentrations for fermentation products. When a working electrode is polarized at -600 mV vs. Ag/AgCl, a shift from butyrate to acetone and butanol production is induced. This leads to an increased final solvent yield of Yᴀᴃᴇ = 0.202 gg⁻¹ (control 0.103 gg⁻¹), which is also reflected in a higher carbon efficiency of 37.6\% compared to 23.3\% (control) as well as a fourfold decrease in simplified E-factor to 0.43. The results are promising for further development of biobutanol production in bioelectrochemical systems in order to fulfil the principles of Green Chemistry.},
  language  = {en}
}
@inproceedings{FingerBraunBil2018,
  author    = {Finger, Felix and Braun, Carsten and Bil, Cees},
  title     = {An Initial Sizing Methodology for Hybrid-Electric Light Aircraft},
  series = {AIAA AVIATION Forum 2018 Aviation Technology, Integration, and Operations Conference, Atlanta, Georgia, June 25 - 29, 2018},
  booktitle = {AIAA AVIATION Forum 2018 Aviation Technology, Integration, and Operations Conference, Atlanta, Georgia, June 25 - 29, 2018},
  doi       = {10.2514/6.2018-4229},
  year      = {2018},
  language  = {en}
}
@incollection{SchoeningPoghossian2018,
  author    = {Sch{\"o}ning, Michael Josef and Poghossian, Arshak},
  title     = {Enzyme und Biosensorik},
  series = {Einf{\"u}hrung in die Enzymtechnologie},
  booktitle = {Einf{\"u}hrung in die Enzymtechnologie},
  publisher = {Springer Spektrum},
  address   = {Berlin},
  isbn      = {978-3-662-57619-9},
  doi       = {10.1007/978-3-662-57619-9_18},
  pages     = {323 -- 347},
  year      = {2018},
  abstract  = {Enzymbasierte Biosensoren finden seit mehr als f{\"u}nf Jahrzehnten einen prosperierenden Wachstumsmarkt und werden zunehmend auch in biotechnologischen Prozessen eingesetzt. In diesem Kapitel werden, ausgehend vom Sensorbegriff und typischen Kenngr{\"o}ßen f{\"u}r Biosensoren (Abschn. 18.1), elektrochemische Enzym-Biosensoren vorgestellt und deren typischen Einsatzgebiete diskutiert (Abschn. 18.2). Ein Blick {\"u}ber den „Tellerrand" hinaus zeigt alternative Transduktorprinzipien (Abschn. 18.3) und f{\"u}hrt abschließend in aktuelle Forschungstrends ein (Abschn. 18.4).},
  language  = {de}
}
@article{HirschKleebergSchmitz2018,
  author    = {Hirsch, Marko and Kleeberg, Jochen and Schmitz, Philipp},
  title     = {Dynamische Asset-Allocation- Strategien im Niedrigzinsumfeld},
  series = {Absolut|report : neue Perspektiven f{\"u}r institutionelle Investoren},
  journal   = {Absolut|report : neue Perspektiven f{\"u}r institutionelle Investoren},
  number    = {6},
  publisher = {Absolut Research},
  address   = {Hamburg},
  pages     = {52},
  year      = {2018},
  language  = {de}
}
@book{FockeSteinbeck2018,
  author    = {Focke, Markus and Steinbeck, J{\"o}rn},
  title     = {Steigerung der Anlagenproduktivit{\"a}t durch OEE-Management : Definitionen, Vorgehen und Methoden - von manuell bis Industrie 4.0},
  publisher = {Springer Fachmedien},
  address   = {Wiesbaden},
  isbn      = {978-3-658-21456-2},
  doi       = {10.1007/978-3-658-21456-2},
  year      = {2018},
  language  = {de}
}
@article{HueningHeuermannWache2018,
  author    = {H{\"u}ning, Felix and Heuermann, Holger and Wache, Franz-Josef},
  title     = {Wireless CAN without WLAN or Bluetooth},
  series = {CAN Newsletter},
  journal   = {CAN Newsletter},
  number    = {December 2018},
  pages     = {44 -- 46},
  year      = {2018},
  abstract  = {In two developed concepts, dual-mode radio enables CAN participants to be integrated wirelessly into a CAN network. Constructed from a few components, a protocol-free, real-time transmission and thus transparent integration into CAN is provided.},
  language  = {en}
}
@inproceedings{BaaderReiswichBartschetal.2018,
  author    = {Baader, Fabian and Reiswich, M. and Bartsch, M. and Keller, D. and Tiede, E. and Keck, G. and Demircian, A. and Friedrich, M. and Dachwald, Bernd and Sch{\"u}ller, K. and Lehmann, R. and Chojetzki, R. and Durand, C. and Rapp, L. and Kowalski, Julia and F{\"o}rstner, R.},
  title     = {VIPER - Student research on extraterrestrical ice penetration technology},
  series = {Proceedings of the 2nd Symposium on Space Educational Activities},
  booktitle = {Proceedings of the 2nd Symposium on Space Educational Activities},
  pages     = {1 -- 6},
  year      = {2018},
  abstract  = {Recent analysis of scientific data from Cassini and earth-based observations gave evidence for a global ocean under a surrounding solid ice shell on Saturn's moon Enceladus. Images of Enceladus' South Pole showed several fissures in the ice shell with plumes constantly exhausting frozen water particles, building up the E-Ring, one of the outer rings of Saturn. In this southern region of Enceladus, the ice shell is considered to be as thin as 2 km, about an order of magnitude thinner than on the rest of the moon. Under the ice shell, there is a global ocean consisting of liquid water. Scientists are discussing different approaches the possibilities of taking samples of water, i.e. by melting through the ice using a melting probe. FH Aachen UAS developed a prototype of maneuverable melting probe which can navigate through the ice that has already been tested successfully in a terrestrial environment. This means no atmosphere and or ambient pressure, low ice temperatures of around 100 to 150K (near the South Pole) and a very low gravity of 0,114 m/s^2 or 1100 μg. Two of these influencing measures are about to be investigated at FH Aachen UAS in 2017, low ice temperature and low ambient pressure below the triple point of water. Low gravity cannot be easily simulated inside a large experiment chamber, though. Numerical simulations of the melting process at RWTH Aachen however are showing a gravity dependence of melting behavior. Considering this aspect, VIPER provides a link between large-scale experimental simulations at FH Aachen UAS and numerical simulations at RWTH Aachen. To analyze the melting process, about 90 seconds of experiment time in reduced gravity and low ambient pressure is provided by the REXUS rocket. In this time frame, the melting speed and contact force between ice and probes are measured, as well as heating power and a two-dimensional array of ice temperatures. Additionally, visual and infrared cameras are used to observe the melting process.},
  language  = {en}
}