@article{KowalewskiBragardHueningetal.2023,
  author    = {Kowalewski, Paul and Bragard, Michael and H{\"u}ning, Felix and De Doncker, Rik W.},
  title     = {An inexpensive Wiegand-sensor-based rotary encoder without rotating magnets for use in electrical drives},
  series = {IEEE Transactions on Instrumentation and Measurement},
  journal   = {IEEE Transactions on Instrumentation and Measurement},
  publisher = {IEEE},
  issn      = {0018-9456 (Print)},
  doi       = {10.1109/TIM.2023.3326166},
  pages     = {10 Seiten},
  year      = {2023},
  abstract  = {This paper introduces an inexpensive Wiegand-sensor-based rotary encoder that avoids rotating magnets and is suitable for electrical-drive applications. So far, Wiegand-sensor-based encoders usually include a magnetic pole wheel with rotating permanent magnets. These encoders combine the disadvantages of an increased magnet demand and a limited maximal speed due to the centripetal force acting on the rotating magnets. The proposed approach reduces the total demand of permanent magnets drastically. Moreover, the rotating part is manufacturable from a single piece of steel, which makes it very robust and cheap. This work presents the theoretical operating principle of the proposed approach and validates its benefits on a hardware prototype. The presented proof-of-concept prototype achieves a mechanical resolution of 4.5 ° by using only 4 permanent magnets, 2Wiegand sensors and a rotating steel gear wheel with 20 teeth.},
  language  = {en}
}
@article{KobusBitzUdenetal.2012,
  author    = {Kobus, Thiele and Bitz, Andreas and Uden, Mark J. van and Lagemaat, Miram W. and Rothgang, Eva and Orzada, Stephan and Heerschap, Arend and Scheenen, Tom W. J.},
  title     = {In vivo 31P MR spectroscopic imaging of the human prostate at 7 T: safety and feasibility},
  series = {Magnetic Resonance in Medicine},
  volume    = {68},
  journal   = {Magnetic Resonance in Medicine},
  number    = {6},
  publisher = {Wiley-Liss},
  address   = {New York},
  issn      = {1522-2594},
  doi       = {10.1002/mrm.24175},
  pages     = {1683 -- 1695},
  year      = {2012},
  abstract  = {31P MR spectroscopic imaging of the human prostate provides information about phosphorylated metabolites that could be used for prostate cancer characterization. The sensitivity of a magnetic field strength of 7 T might enable 3D 31P MR spectroscopic imaging with relevant spatial resolution in a clinically acceptable measurement time. To this end, a 31P endorectal coil was developed and combined with an eight-channel 1H body-array coil to relate metabolic information to anatomical location. An extensive safety validation was performed to evaluate the specific absorption rate, the radiofrequency field distribution, and the temperature distribution of both coils. This validation consisted of detailed Finite Integration Technique simulations, confirmed by MR thermometry and Burn:x-wiley:07403194:media:MRM24175:tex2gif-stack-1 measurements in a phantom and in vivo temperature measurements. The safety studies demonstrated that the presence of the 31P endorectal coil had no influence on the specific absorption rate levels and temperature distribution of the external eight-channel 1H array coil. To stay within a 10 g averaged local specific absorption rate of 10 W/kg, a maximum time-averaged input power of 33 W for the 1H array coil was allowed. For transmitting with the 31P endorectal coil, our safety limit of less than 1°C temperature increase in vivo during a 15-min MR spectroscopic imaging experiment was reached at a time-averaged input power of 1.9 W. With this power setting, a second in vivo measurement was performed on a healthy volunteer. Using adiabatic excitation, 3D 31P MR spectroscopic imaging produced spectra from the entire prostate in 18 min with a spatial resolution of 4 cm3. The spectral resolution enabled the separate detection of phosphocholine, phosphoethanolamine, inorganic phosphate, and other metabolites that could play an important role in the characterization of prostate cancer.},
  language  = {en}
}
@article{KlompBitzHeerschapetal.2009,
  author    = {Klomp, D. W. J. and Bitz, Andreas and Heerschap, A. and Scheenen, T. W. J.},
  title     = {Proton spectroscopic imaging of the human prostate at 7 T},
  series = {NMR in Biomedicine},
  volume    = {22},
  journal   = {NMR in Biomedicine},
  number    = {5},
  issn      = {1099-1492},
  doi       = {10.1002/nbm.1360},
  pages     = {495 -- 501},
  year      = {2009},
  language  = {en}
}
@article{KlingeOttoMuehl2015,
  author    = {Klinge, Uwe and Otto, Jens and M{\"u}hl, Thomas},
  title     = {High Structural Stability of Textile Implants Prevents Pore Collapse and Preserves Effective Porosity at Strain},
  series = {BioMed Research International},
  volume    = {2015},
  journal   = {BioMed Research International},
  issn      = {2314-6133 (Print)},
  doi       = {10.1155/2015/953209},
  pages     = {7 pages},
  year      = {2015},
  language  = {en}
}
@article{JensKaldenhoffKirschnerHermannsetal.2014,
  author    = {Jens, Otto and Kaldenhoff, E. and Kirschner-Hermanns, R. and M{\"u}hl, Thomas and Klinge, Uwe},
  title     = {Elongation of textile pelvic floor implants under load is related to complete loss of effective porosity, thereby favoring incorporation in scar plates},
  series = {Journal of biomedical materials research. Part A},
  volume    = {102},
  journal   = {Journal of biomedical materials research. Part A},
  number    = {4},
  publisher = {Wiley},
  address   = {New York},
  issn      = {1552-4965},
  doi       = {10.1002/jbm.a.34767},
  pages     = {1079 -- 1084},
  year      = {2014},
  abstract  = {Use of textile structures for reinforcement of pelvic floor structures has to consider mechanical forces to the implant, which are quite different to the tension free conditions of the abdominal wall. Thus, biomechanical analysis of textile devices has to include the impact of strain on stretchability and effective porosity. Prolift® and Prolift + M®, developed for tension free conditions, were tested by measuring stretchability and effective porosity applying mechanical strain. For comparison, we used Dynamesh-PR4®, which was designed for pelvic floor repair to withstand mechanical strain. Prolift® at rest showed moderate porosity with little stretchability but complete loss of effective porosity at strain of 4.9 N/cm. Prolift + M® revealed an increased porosity at rest, but at strain showed high stretchability, with subsequent loss of effective porosity at strain of 2.5 N/cm. Dynamesh PR4® preserved its high porosity even under strain, but as consequence of limited stretchability. Though in tension free conditions Prolift® and Prolift + M® can be considered as large pore class I meshes, application of mechanical strain rapidly lead to collapse of pores. The loss of porosity at mechanical stress can be prevented by constructions with high structural stability. Assessment of porosity under strain was found helpful to define requirements for pelvic floor devices. Clinical studies have to prove whether devices with high porosity as well as high structural stability can improve the patients' outcome.},
  language  = {en}
}
@article{HueningWilkeNakielskietal.1997,
  author    = {H{\"u}ning, Felix and Wilke, I. and Nakielski, G. and Kotzler, J.},
  title     = {Dynamic conductivity of YBCO thin films from low to very high frequencies / Wilke, I. ; Nakielski, G. ; Kotzler, J. ; Subke, K. O. ; Jaekel, C. ; H{\"u}ning, F. ; Roskos, H. G. ; Kurz, Heinrich},
  series = {Applied superconductivity 1997 : proceedings of EUCAS 1997, the Third European Conference on Applied Superconductivity, held in the Netherlands, 30 June - 3 July 1997 / ed. by H. Rogalla},
  journal   = {Applied superconductivity 1997 : proceedings of EUCAS 1997, the Third European Conference on Applied Superconductivity, held in the Netherlands, 30 June - 3 July 1997 / ed. by H. Rogalla},
  publisher = {IOP},
  address   = {Bristol},
  isbn      = {0-7503-0487-1},
  pages     = {121 -- 124},
  year      = {1997},
  language  = {en}
}
@article{HueningSpartaRedhammeretal.2001,
  author    = {H{\"u}ning, Felix and Sparta, K. and Redhammer, G. J. and Roussel, P.},
  title     = {Structural Phase Transition in the 2D Spin Dimer Compound SrCu2(BO3)2 / Sparta, K. ; Redhammer, G. J. ; Roussel, P. ; Heger, G. ; Roth, G. ; Ionescu, A. Lemmens, P. ; Grove, M. ; G{\"u}ntherrodt, G. ; H{\"u}ning, F. ; Lueken, H. ; Kageyama, H. ; Onizuka, K ; Ueda},
  series = {The European Physical Journal B - Condensed Matter and Complex Systems. 19 (2001), H. 4},
  journal   = {The European Physical Journal B - Condensed Matter and Complex Systems. 19 (2001), H. 4},
  publisher = {-},
  isbn      = {1434-6036},
  pages     = {507 -- 516},
  year      = {2001},
  language  = {en}
}
@article{HueningLukenSchilderetal.2001,
  author    = {H{\"u}ning, Felix and Luken, Heiko and Schilder, Herbert and Eifert, Thomas},
  title     = {Magnetochemistry: Compounds and Concepts / Lueken, Heiko ; Schilder, Herbert ; Eifert, Thomas ; Handrick, Klaus ; H{\"u}ning, Felix},
  series = {Advances in Solid State Physics. 201 (2001)},
  journal   = {Advances in Solid State Physics. 201 (2001)},
  publisher = {-},
  pages     = {515 -- 532},
  year      = {2001},
  language  = {en}
}
@article{HueningLeineweberJacobsetal.1999,
  author    = {H{\"u}ning, Felix and Leineweber, A. and Jacobs, H. and Lueken, H.},
  title     = {ε-Fe3N: magnetic structure, magnetization and temperature dependent disorder of nitrogen / Leineweber, A. ; Jacobs, H. ; H{\"u}ning, F. ; Lueken, H. ; Schilder, H. ; Kockelmann, W.},
  series = {Journal of Alloys and Compounds. 288 (1999), H. 1-2},
  volume    = {288},
  journal   = {Journal of Alloys and Compounds. 288 (1999), H. 1-2},
  number    = {1-2},
  publisher = {Elsevier},
  address   = {Amsterdam},
  isbn      = {1873-4669},
  pages     = {79 -- 87},
  year      = {1999},
  abstract  = {ε-Fe3N has been investigated by time-of-flight neutron diffraction (temperature range 4.2-618 K) and SQUID magnetometry (2-700 K, B≤5 T). A ferromagnetic spin structure is observed with magnetic moments oriented perpendicular to the c-axis of the hexagonal nuclear structure. The magnetic saturation moment of iron is 2.2 μB at 4.2 K from neutron diffraction and 2.0 μB from magnetic measurements and decreases in a Brillouin-like manner on heating to TC=575 K. Above 450 K an increasing but reversible disorder of the nitrogen partial structure is observed.},
  language  = {en}
}
@article{HueningLeineweberJacobsetal.2001,
  author    = {H{\"u}ning, Felix and Leineweber, A. and Jacobs, H. and Lueken, H.},
  title     = {Nitrogen Ordering and ferromagnetic properties of -Fe3N1+x (0.10  x  0.39) and -Fe3(N0.80C0.20)1.38 / Leineweber, A. ; Jacobs, H. ; H{\"u}ning, F. ; Lueken, H. ; Kockelmann, W.},
  series = {Journal of Alloys and Compounds. 316 (2001), H. 1-2},
  journal   = {Journal of Alloys and Compounds. 316 (2001), H. 1-2},
  publisher = {-},
  isbn      = {1873-4669},
  pages     = {21 -- 38},
  year      = {2001},
  language  = {en}
}
@article{HueningJaekelFrancoisetal.1996,
  author    = {H{\"u}ning, Felix and Jaekel, C. and Francois, I. and Kyas, G.},
  title     = {Microwave surface impedance measurements on high-Tc superconductors / Jaekel, C. ; Francois, I. ; Kyas, G. ; H{\"u}ning, F. ; Roskos, H. G. ; Borghs, G. ; Kurz, H.},
  series = {Czechoslovak Journal of Physics. 46 (1996), H. Suppl. 2},
  journal   = {Czechoslovak Journal of Physics. 46 (1996), H. Suppl. 2},
  number    = {46},
  publisher = {Springer Science+Business Media},
  address   = {Dordrecht},
  isbn      = {1572-9486},
  pages     = {1117 -- 1118},
  year      = {1996},
  language  = {en}
}
@article{HueningHeuermannWacheetal.2018,
  author    = {H{\"u}ning, Felix and Heuermann, Holger and Wache, Franz-Josef and Jajo, Rami Audisho},
  title     = {A new wireless sensor interface using dual-mode radio},
  series = {Journal of Sensors and Sensor Systems : JSSS},
  volume    = {Volume 7},
  journal   = {Journal of Sensors and Sensor Systems : JSSS},
  number    = {2},
  publisher = {Copernicus Publ.},
  address   = {G{\"o}ttingen},
  doi       = {10.5194/jsss-7-507-2018},
  pages     = {507 -- 515},
  year      = {2018},
  abstract  = {The integration of sensors is one of the major tasks in embedded, control and "internet of things" (IoT) applications. For the integration mainly digital interfaces are used, starting from rather simple pulse-width modulation (PWM) interface to more complex interfaces like CAN (Controller Area Network). Even though these interfaces are tethered by definition, a wireless realization is highly welcome in many applications to reduce cable and connector cost, increase the flexibility and realize new emerging applications like wireless control systems. Currently used wireless solutions like Bluetooth, WirelessHART or IO-Link Wireless use dedicated communication standards and corresponding higher protocol layers to realize the wireless communication. Due to the complexity of the communication and the protocol handling, additional latency and jitter are introduced to the data communication that can meet the requirements for many applications. Even though tunnelling of other bus data like CAN data is generally also possible the latency and jitter prevent the tunnelling from being transparent for the bus system. Therefore a new basic technology based on dual-mode radio is used to realize a wireless communication on the physical layer only, enabling a reliable and real-time data transfer. As this system operates on the physical layer it is independent of any higher layers of the OSI (open systems interconnection) model. Hence it can be used for several different communication systems to replace the tethered physical layer. A prototype is developed and tested for real-time wireless PWM, SENT (single-edge nibble transmission) and CAN data transfer with very low latency and jitter.},
  language  = {en}
}
@article{HueningHeuermannWache2018,
  author    = {H{\"u}ning, Felix and Heuermann, Holger and Wache, Franz-Josef},
  title     = {Wireless CAN without WLAN or Bluetooth},
  series = {CAN Newsletter},
  journal   = {CAN Newsletter},
  number    = {December 2018},
  pages     = {44 -- 46},
  year      = {2018},
  abstract  = {In two developed concepts, dual-mode radio enables CAN participants to be integrated wirelessly into a CAN network. Constructed from a few components, a protocol-free, real-time transmission and thus transparent integration into CAN is provided.},
  language  = {en}
}
@article{HueningEifertLuekenetal.2002,
  author    = {H{\"u}ning, Felix and Eifert, T. and Lueken, H. and Schmidt, P.},
  title     = {High-temperature series expansion of the magnetic susceptibility of extended magnetic systems in a complete computer implementation / Eifert, T. ; H{\"u}ning, F. ; Lueken, H. ; Schmidt, P. ; Thiele, G.},
  series = {Chemical Physics Letters. 364 (2002), H. 1-2},
  journal   = {Chemical Physics Letters. 364 (2002), H. 1-2},
  publisher = {-},
  isbn      = {0009-2614},
  pages     = {69 -- 74},
  year      = {2002},
  language  = {en}
}
@article{HueningEifertHandricketal.2006,
  author    = {H{\"u}ning, Felix and Eifert, T. and Handrick, K. and Neuhausen, U.},
  title     = {Computational Magnetochemistry: Complementary Quantum Mechanical Tools / Eifert, T. ; Handrick, K. ; H{\"u}ning, F. ; Neuhausen, U. ; Schilder, H. ; Lueken, H.},
  series = {Zeitschrift f{\"u}r Anorganische und Allgemeine Chemie (ZAAC) - Journal of Inorganic and General Chemistry . 632 (2006), H. 4},
  journal   = {Zeitschrift f{\"u}r Anorganische und Allgemeine Chemie (ZAAC) - Journal of Inorganic and General Chemistry . 632 (2006), H. 4},
  publisher = {-},
  isbn      = {1521-3749},
  pages     = {521 -- 529},
  year      = {2006},
  language  = {en}
}
@article{HueningEifertHandricketal.2006,
  author    = {H{\"u}ning, Felix and Eifert, T. and Handrick, K. and Neuhausen, U.},
  title     = {Computational Magnetochemistry: Complementary Quantum Mechanical Tools / Eifert, T. ; Handrick, K. ; H{\"u}ning, F. ; Neuhausen, U. ; Schilder, H. ; Lueken, H.},
  series = {20 Jahre Wilhelm-Klemm-Stiftung / Kuratorium der Wilhelm-Klemm-Stiftung (Hrsg.)},
  journal   = {20 Jahre Wilhelm-Klemm-Stiftung / Kuratorium der Wilhelm-Klemm-Stiftung (Hrsg.)},
  publisher = {Shaker},
  address   = {Aachen},
  isbn      = {978-3-8322-5520-6},
  pages     = {193ff},
  year      = {2006},
  language  = {en}
}
@article{HueningBackes2020,
  author    = {H{\"u}ning, Felix and Backes, Andreas},
  title     = {Direct observation of large Barkhausen jump in thin Vicalloy wires},
  series = {IEEE Magnetics Letters},
  volume    = {11},
  journal   = {IEEE Magnetics Letters},
  number    = {Art. 2506504},
  publisher = {IEEE},
  address   = {New York, NY},
  isbn      = {1949-307X},
  doi       = {10.1109/LMAG.2020.3046411},
  pages     = {1 -- 4},
  year      = {2020},
  language  = {en}
}
@article{Huening2008,
  author    = {H{\"u}ning, Felix},
  title     = {Entwicklungstrends bei MOSFETs f{\"u}r den Automobilbereich},
  series = {Elektronik-Industrie . 39 (2008), H. 5},
  journal   = {Elektronik-Industrie . 39 (2008), H. 5},
  publisher = {-},
  isbn      = {0174-5522},
  pages     = {74 -- 76},
  year      = {2008},
  language  = {en}
}
@article{Huening2009,
  author    = {H{\"u}ning, Felix},
  title     = {SMD packages for PowerMOSFETs in automotive applications - developments and trends},
  series = {Automotive Designline Europe (2009)},
  journal   = {Automotive Designline Europe (2009)},
  publisher = {-},
  year      = {2009},
  language  = {en}
}
@article{Huening2012,
  author    = {H{\"u}ning, Felix},
  title     = {Using Trench PowerMOSFETs in Linear Mode},
  series = {Power Electronics Europe (2012)},
  journal   = {Power Electronics Europe (2012)},
  publisher = {DFA Media},
  address   = {Tonbridge},
  issn      = {1748-3530},
  pages     = {27 -- 29},
  year      = {2012},
  abstract  = {If we think about applications for modern Power MOSFETs using trench technology, running them in linear mode may not be top of the priority list. Yet there are multiple uses for Trench Power MOSFETs in linear mode. In fact, even turning the device on and off in switching applications is a form of linear operation. Also, these components can be run in linear mode to protect the device against voltage surges. This article will illustrate the factors that need to be considered for linear operation and show how Trench Power MOSFETs are suited to it.},
  language  = {en}
}
@article{HulseboschGuentherHornetal.2004,
  author    = {Hulsebosch, R. J. and G{\"u}nther, C. and Horn, C. and Holtmanns, S. and Howker, K. and Paterson, K. and Claessens, J. and Schuba, Marko},
  title     = {Pioneering Advanced Mobile Privacy and Security},
  series = {Security for mobility},
  journal   = {Security for mobility},
  editor    = {Mitchell, Chris J.},
  publisher = {Institution of Electrical Engineers},
  address   = {London},
  isbn      = {9781849190886},
  doi       = {10.1049/PBTE051E_ch},
  pages     = {383 -- 432},
  year      = {2004},
  language  = {en}
}
@article{HoltrupSadeghfamHeuermannetal.2014,
  author    = {Holtrup, S. and Sadeghfam, Arash and Heuermann, Holger and Awakowicz, P.},
  title     = {Characterization and optimization technique for microwave-driven high-intensity discharge lamps using hot S-parameters},
  series = {IEEE transactions on microwave theories and techniques},
  volume    = {62},
  journal   = {IEEE transactions on microwave theories and techniques},
  number    = {10},
  publisher = {IEEE},
  address   = {New York},
  issn      = {0018-9480},
  doi       = {10.1109/TMTT.2014.2342652},
  pages     = {2471 -- 2480},
  year      = {2014},
  abstract  = {High-intensity discharge lamps can be driven by radio-frequency signals in the ISM frequency band at 2.45 GHz, using a matching network to transform the impedance of the plasma to the source impedance. To achieve an optimal operating condition, a good characterization of the lamp in terms of radio frequency equivalent circuits under operating conditions is necessary, enabling the design of an efficient matching network. This paper presents the characterization technique for such lamps and presents the design of the required matching network. For the characterization, a high-intensity discharge lamp was driven by a monofrequent large signal at 2.45 GHz, whereas a frequency sweep over 300 MHz was performed across this signal to measure so-called small-signal hot S-parameters using a vector network analyzer. These parameters are then used as an equivalent load in a circuit simulator to design an appropriate matching network. Using the measured data as a black-box model in the simulation results in a quick and efficient method to simulate and design efficient matching networks in spite of the complex plasma behavior. Furthermore, photometric analysis of high-intensity discharge lamps are carried out, comparing microwave operation to conventional operation.},
  language  = {en}
}
@article{HofmannLimpertMatareetal.2018,
  author    = {Hofmann, Till and Limpert, Nicolas and Matar{\´e}, Victor and Sch{\"o}nitz, Sebastian and Niemueller, Tim and Ferrein, Alexander and Lakemeyer, Gerhard},
  title     = {The Carologistics RoboCup Logistics Team 2018},
  year      = {2018},
  abstract  = {The Carologistics team participates in the RoboCup Logistics League for the seventh year. The RCLL requires precise vision, manipulation and path planning, as well as complex high-level decision making and multi-robot coordination. We outline our approach with an emphasis on recent modifications to those components. The team members in 2018 are David Bosen, Christoph Gollok, Mostafa Gomaa, Daniel Habering, Till Hofmann, Nicolas Limpert, Sebastian Sch{\"o}nitz, Morian Sonnet, Carsten Stoffels, and Tarik Viehmann. This paper is based on the last year's team description.},
  language  = {en}
}
@article{HoffmannRohrbachUhletal.2022,
  author    = {Hoffmann, Andreas and Rohrbach, Felix and Uhl, Matthias and Ceblin, Maximilian and Bauer, Thomas and Mallah, Marcel and Jacob, Timo and Heuermann, Holger and Kuehne, Alexander J. C.},
  title     = {Atmospheric pressure plasma-jet treatment of polyacrylonitrile-nonwovens—Stabilization and roll-to-roll processing},
  series = {Journal of Applied Polymer Science},
  volume    = {139},
  journal   = {Journal of Applied Polymer Science},
  number    = {37},
  publisher = {Wiley},
  issn      = {0021-8995 (Print)},
  doi       = {10.1002/app.52887},
  pages     = {1 -- 9},
  year      = {2022},
  abstract  = {Carbon nanofiber nonwovens represent a powerful class of materials with prospective application in filtration technology or as electrodes with high surface area in batteries, fuel cells, and supercapacitors. While new precursor-to-carbon conversion processes have been explored to overcome productivity restrictions for carbon fiber tows, alternatives for the two-step thermal conversion of polyacrylonitrile precursors into carbon fiber nonwovens are absent. In this work, we develop a continuous roll-to-roll stabilization process using an atmospheric pressure microwave plasma jet. We explore the influence of various plasma-jet parameters on the morphology of the nonwoven and compare the stabilized nonwoven to thermally stabilized samples using scanning electron microscopy, differential scanning calorimetry, and infrared spectroscopy. We show that stabilization with a non-equilibrium plasma-jet can be twice as productive as the conventional thermal stabilization in a convection furnace, while producing electrodes of comparable electrochemical performance.},
  language  = {en}
}
@article{HillgaertnerStoniesPeieretal.2005,
  author    = {Hillg{\"a}rtner, Michael and Stonies, R. and Peier, D. and Voges, E.},
  title     = {Design of Low Cost Antennas for Reverberation Chambers},
  series = {Proceedings of the 16th International Zurich Symposium on Electromagnetic Compatibility : [EMC Week 2005, Zurich, Switzerland, February 13 - 18 ; technical exhibition on EMC and RF/microwave Measurements and Instrumentation (February 15 - 17)] / [Laboratory for Electromagnetic Fields and Microwave Electronics, Swiss Federal Institute of Technology Zurich]},
  journal   = {Proceedings of the 16th International Zurich Symposium on Electromagnetic Compatibility : [EMC Week 2005, Zurich, Switzerland, February 13 - 18 ; technical exhibition on EMC and RF/microwave Measurements and Instrumentation (February 15 - 17)] / [Laboratory for Electromagnetic Fields and Microwave Electronics, Swiss Federal Institute of Technology Zurich]},
  publisher = {ETH-Zentrum-IFH},
  address   = {Z{\"u}rich},
  isbn      = {3-9521199-9-7},
  pages     = {1 CD-ROM. ; 12 cm},
  year      = {2005},
  language  = {en}
}
@article{HillgaertnerPeier2006,
  author    = {Hillg{\"a}rtner, Michael and Peier, Dirk},
  title     = {Design of a Measurement Setup for the Impedance of Low-Resistance Plate-Conductors in the RF-Range},
  series = {Proceedings of the 10th International Conference on Optimization of Electrical and Electronic Equipment, OPTIM '06, Bra\&\#351;ov, May 18 - 20, 2006 / ed. by The Transilvania University of Bra\&\#351;ov, Faculty of Electrical Engineering and Computer Science. [Ed. Mihai Cernat .\&\#804;] . - Vol. 1: Keynote addresses, electrotechnics},
  journal   = {Proceedings of the 10th International Conference on Optimization of Electrical and Electronic Equipment, OPTIM '06, Bra\&\#351;ov, May 18 - 20, 2006 / ed. by The Transilvania University of Bra\&\#351;ov, Faculty of Electrical Engineering and Computer Science. [Ed. Mihai Cernat .\&\#804;] . - Vol. 1: Keynote addresses, electrotechnics},
  address   = {Bra\&\#351;ov},
  isbn      = {978-973-635703-9},
  pages     = {59 -- 64},
  year      = {2006},
  language  = {en}
}
@article{HillgaertnerKappel2006,
  author    = {Hillg{\"a}rtner, Michael and Kappel, U.},
  title     = {Radiating Impedance of Mains Cabling During Emissions Testing},
  series = {EMC Europe 2006 Barcelona : International Symposium on Electromagnetic Compatibility; September 4 - 8, 2006, Campus Nord, Technical University of Catalonia, Barcelona, Spain / [organized by Technical University of Catalonia (UPC) ... Ed. and publ. by: Ferran Silva ...]. - Vol. 1: Proceedings 1},
  journal   = {EMC Europe 2006 Barcelona : International Symposium on Electromagnetic Compatibility; September 4 - 8, 2006, Campus Nord, Technical University of Catalonia, Barcelona, Spain / [organized by Technical University of Catalonia (UPC) ... Ed. and publ. by: Ferran Silva ...]. - Vol. 1: Proceedings 1},
  address   = {Barcelona},
  isbn      = {84-689-9439-1},
  pages     = {17 -- 22},
  year      = {2006},
  language  = {en}
}
@article{Hillgaertner2010,
  author    = {Hillg{\"a}rtner, Michael},
  title     = {Normative Regulations},
  series = {ECPE Cluster Seminar EMC in Hybrid and Electric Vehicles : 18 May 2010, Fraunhofer Institute Erlangen},
  journal   = {ECPE Cluster Seminar EMC in Hybrid and Electric Vehicles : 18 May 2010, Fraunhofer Institute Erlangen},
  publisher = {European Center for Power Electronics},
  address   = {N{\"u}rnberg},
  pages     = {1 CD-ROM},
  year      = {2010},
  language  = {en}
}
@article{HeuermannThalayasingam2009,
  author    = {Heuermann, Holger and Thalayasingam, K.},
  title     = {Novel vector non-linear measurement system for intermodulation measurements / Thalayasingam, K.; Heuermann, H.},
  series = {European Microwave Conference, 2009 : EuMC 2009 ; Sept. 29, 2009 - Oct. 1, 2009, Rome, Italy ; part of European Microwave Week (EuMW) / sponsored by EuMA, European Microwave Association ... Endorsed by IEEE},
  journal   = {European Microwave Conference, 2009 : EuMC 2009 ; Sept. 29, 2009 - Oct. 1, 2009, Rome, Italy ; part of European Microwave Week (EuMW) / sponsored by EuMA, European Microwave Association ... Endorsed by IEEE},
  publisher = {IEEE},
  address   = {Piscataway, NJ},
  isbn      = {978-1-4244-4748-0},
  pages     = {926 -- 929},
  year      = {2009},
  language  = {en}
}
@article{HeuermannStolleSchiek1995,
  author    = {Heuermann, Holger and Stolle, Reinhard and Schiek, Burkhard},
  title     = {Novel Algorithms for FMCW Range Finding with Microwaves. Stolle, R.; Heuermann, H.; Schiek, B.},
  pages     = {129 -- 132},
  year      = {1995},
  language  = {en}
}
@article{HeuermannSchiek1997,
  author    = {Heuermann, Holger and Schiek, Burkhard},
  title     = {Line Network Network (LNN): an alternative in-fixture calibration procedure},
  series = {IEEE transactions on microwave theory and techniques : MTT ; a publication of the IEEE Microwave Theory and Techniques Society. 45 (1997), H. 3},
  journal   = {IEEE transactions on microwave theory and techniques : MTT ; a publication of the IEEE Microwave Theory and Techniques Society. 45 (1997), H. 3},
  isbn      = {0018-9480},
  pages     = {408 -- 413},
  year      = {1997},
  language  = {en}
}
@article{HeuermannSchiek1994,
  author    = {Heuermann, Holger and Schiek, Burkhard},
  title     = {Calibration of network analyser measurements with leakage errors},
  series = {Electronics letters. 30 (1994), H. 1},
  journal   = {Electronics letters. 30 (1994), H. 1},
  isbn      = {0013-5194},
  pages     = {52 -- 53},
  year      = {1994},
  language  = {en}
}
@article{HeuermannSchiek1992,
  author    = {Heuermann, Holger and Schiek, Burkhard},
  title     = {LNN (Line-Network-Network): Verfahren zur Kalibrierung von Netzwerkanalysatoren},
  series = {Kleinheubacher Berichte : Vortr{\"a}ge und Berichte der gemeinsamen Tagung des U.R.S.I.-Landesausschusses in der Bundesrepublik Deutschland / Hrsg.: Deutsche Telekom AG. 36. 1992 (1992)},
  journal   = {Kleinheubacher Berichte : Vortr{\"a}ge und Berichte der gemeinsamen Tagung des U.R.S.I.-Landesausschusses in der Bundesrepublik Deutschland / Hrsg.: Deutsche Telekom AG. 36. 1992 (1992)},
  pages     = {327 -- 335},
  year      = {1992},
  language  = {en}
}
@article{HeuermannSchiek1993,
  author    = {Heuermann, Holger and Schiek, Burkhard},
  title     = {LNN( Line-Network-Network): The In-Fixture Calibration Procedure},
  pages     = {149 -- 149},
  year      = {1993},
  language  = {en}
}
@article{HeuermannSchiek1992,
  author    = {Heuermann, Holger and Schiek, Burkhard},
  title     = {A Fast and Robust Procedure for the Determination of the Scattering Parameters for Network Analyzer Calibration},
  address   = {Paris},
  pages     = {373 -- 374},
  year      = {1992},
  language  = {en}
}
@article{HeuermannSchiek1994,
  author    = {Heuermann, Holger and Schiek, Burkhard},
  title     = {Error Corrected Impedance Measurements with a Network Analyzer},
  pages     = {125 -- 126},
  year      = {1994},
  language  = {en}
}
@article{HeuermannSchiek1992,
  author    = {Heuermann, Holger and Schiek, Burkhard},
  title     = {A Generalization of the Txx Network Analyzer Self-Calibration Procedure},
  series = {Conference proceedings : monday 24th to thursday 27th august 1992, Helsinki University of Technology, Espoo, Finland ; [the international conference and exhibition designed for the Microwave Community]. Vol. 2},
  journal   = {Conference proceedings : monday 24th to thursday 27th august 1992, Helsinki University of Technology, Espoo, Finland ; [the international conference and exhibition designed for the Microwave Community]. Vol. 2},
  publisher = {Microwave Exhibitions and Publishers},
  address   = {Tunbridge Wells},
  isbn      = {0-946821-77-1},
  pages     = {907 -- 912},
  year      = {1992},
  language  = {en}
}
@article{HeuermannSchiek1992,
  author    = {Heuermann, Holger and Schiek, Burkhard},
  title     = {The In-Fixture Calibration Procedure Line-Network-Network-LNN},
  series = {Conference proceedings : monday 6th to thursday 9th september 1993, Palacio de Congresos, Madrid, Spain ; [the international conference and exhibition designed for the Microwave Community]},
  journal   = {Conference proceedings : monday 6th to thursday 9th september 1993, Palacio de Congresos, Madrid, Spain ; [the international conference and exhibition designed for the Microwave Community]},
  publisher = {Reed Exhibition Companies},
  address   = {Tunbridge Wells},
  isbn      = {0-946821-23-2},
  pages     = {500 -- 505},
  year      = {1992},
  language  = {en}
}
@article{HeuermannSchiek1994,
  author    = {Heuermann, Holger and Schiek, Burkhard},
  title     = {Scattering Parameter Measurements of Microstrip Devices using the Double-LNN Calibration Technique},
  series = {Conference proceedings : [Palais des Festivals et des Congr{\`e}s Cannes, France, 5 - 8 September 1994]},
  journal   = {Conference proceedings : [Palais des Festivals et des Congr{\`e}s Cannes, France, 5 - 8 September 1994]},
  publisher = {Nexus Business Communications},
  address   = {Swanley},
  isbn      = {0-9518032-5-5},
  year      = {1994},
  language  = {en}
}
@article{HeuermannSchiek1995,
  author    = {Heuermann, Holger and Schiek, Burkhard},
  title     = {The double-LNN Calibration technique for scattering parameter measurements of microstrip devices},
  series = {Conference proceedings},
  journal   = {Conference proceedings},
  publisher = {NEXUS House},
  address   = {Kent},
  pages     = {343 -- 347},
  year      = {1995},
  language  = {en}
}
@article{HeuermannSchiek1994,
  author    = {Heuermann, Holger and Schiek, Burkhard},
  title     = {Results of Network Analyzer Measurements with Leakage Errors Corrected with the TMS-15-Term Procedure},
  pages     = {1361 -- 1364},
  year      = {1994},
  language  = {en}
}
@article{HeuermannSchiek1993,
  author    = {Heuermann, Holger and Schiek, B.},
  title     = {Procedures for the Determination of the Scattering Parameters for Network Analyzer Calibration},
  series = {IEEE transactions on instrumentation and measurement : IM / Institute of Electrical and Electronics Engineers, Instrumentation and Measurement Group. 42 (1993), H. 2},
  journal   = {IEEE transactions on instrumentation and measurement : IM / Institute of Electrical and Electronics Engineers, Instrumentation and Measurement Group. 42 (1993), H. 2},
  isbn      = {0018-9456},
  pages     = {528 -- 531},
  year      = {1993},
  language  = {en}
}
@article{HeuermannSchiek1994,
  author    = {Heuermann, Holger and Schiek, B.},
  title     = {Robust Algorithms for Txx Network Analyzer Self-Calibration Procedures},
  series = {IEEE transactions on instrumentation and measurement : IM / Institute of Electrical and Electronics Engineers, Instrumentation and Measurement Group. 43 (1994), H. 1},
  journal   = {IEEE transactions on instrumentation and measurement : IM / Institute of Electrical and Electronics Engineers, Instrumentation and Measurement Group. 43 (1994), H. 1},
  isbn      = {0018-9456},
  pages     = {18 -- 23},
  year      = {1994},
  language  = {en}
}
@article{HeuermannSchiek1995,
  author    = {Heuermann, Holger and Schiek, B.},
  title     = {Error corrected impedance measurements with a network analyzer},
  series = {IEEE transactions on instrumentation and measurement : IM / Institute of Electrical and Electronics Engineers, Instrumentation and Measurement Group. 44 (1995), H. 2},
  journal   = {IEEE transactions on instrumentation and measurement : IM / Institute of Electrical and Electronics Engineers, Instrumentation and Measurement Group. 44 (1995), H. 2},
  isbn      = {0018-9456},
  pages     = {295 -- 299},
  year      = {1995},
  language  = {en}
}
@article{HeuermannSchiek1997,
  author    = {Heuermann, Holger and Schiek, B.},
  title     = {Results of network analyzer measurements with leakage errors-corrected with direct calibration techniques},
  series = {IEEE transactions on instrumentation and measurement : IM / Institute of Electrical and Electronics Engineers, Instrumentation and Measurement Group. 46 (1997), H. 5},
  journal   = {IEEE transactions on instrumentation and measurement : IM / Institute of Electrical and Electronics Engineers, Instrumentation and Measurement Group. 46 (1997), H. 5},
  isbn      = {0018-9456},
  pages     = {1120 -- 1127},
  year      = {1997},
  language  = {en}
}
@article{HeuermannSchiek1997,
  author    = {Heuermann, Holger and Schiek, B.},
  title     = {15-term self-calibration methods for the error-correction of on-wafer measurements},
  series = {IEEE transactions on instrumentation and measurement : IM / Institute of Electrical and Electronics Engineers, Instrumentation and Measurement Group. 46 (1997), H. 5},
  journal   = {IEEE transactions on instrumentation and measurement : IM / Institute of Electrical and Electronics Engineers, Instrumentation and Measurement Group. 46 (1997), H. 5},
  isbn      = {0018-9456},
  pages     = {1105 -- 1110},
  year      = {1997},
  language  = {en}
}
@article{HeuermannSadeghfamBoehm2005,
  author    = {Heuermann, Holger and Sadeghfam, Arash and Boehm, H.},
  title     = {Ultra Compact Multi-Mode Filter with Novel Rat-Race Inductor. Sadeghfam, Arash; Heuermann, Holger; Boehm, H.},
  series = {Conference proceedings : 3 - 7 October 2005, CNIT la D{\´e}fense, Paris, France; [comprises the] 35th European Microwave Conference 2005 ; The European Conference on Wireless Technology 2005 ; European Radar Conference 2005 ; GAAS 2005, The European Gallium A. Vol. 2},
  journal   = {Conference proceedings : 3 - 7 October 2005, CNIT la D{\´e}fense, Paris, France; [comprises the] 35th European Microwave Conference 2005 ; The European Conference on Wireless Technology 2005 ; European Radar Conference 2005 ; GAAS 2005, The European Gallium A. Vol. 2},
  publisher = {Horizon House Publ},
  address   = {London},
  isbn      = {2-9600551-0-1},
  pages     = {4 pp.},
  year      = {2005},
  language  = {en}
}
@article{HeuermannSadeghfam2004,
  author    = {Heuermann, Holger and Sadeghfam, Arash},
  title     = {Novel balanced inductor for compact differential systems / Sadeghfam, Arash; Heuermann, Holger},
  series = {Conference proceedings : Tuesday 12th, Wednesday 13th and Thursday 14th October, [RAI International Exhibition and Congress Centre, Amsterdam ; part of European Microwave Week 2004] / EuMA, European Microwave Association},
  journal   = {Conference proceedings : Tuesday 12th, Wednesday 13th and Thursday 14th October, [RAI International Exhibition and Congress Centre, Amsterdam ; part of European Microwave Week 2004] / EuMA, European Microwave Association},
  publisher = {Horizon House Publ.},
  address   = {London},
  isbn      = {1-580-53992-0},
  pages     = {709 -- 712},
  year      = {2004},
  language  = {en}
}
@article{HeuermannSadeghfam2008,
  author    = {Heuermann, Holger and Sadeghfam, Arash},
  title     = {Electrically tunable bandpass filter with integrated carrier suppression for UHF RFID systems / Sadeghfam, Arash ; Heuermann, Holger},
  series = {European Microwave Conference, 2008, EuMC 2008, 38th},
  journal   = {European Microwave Conference, 2008, EuMC 2008, 38th},
  isbn      = {978-2-87487-006-4},
  pages     = {1727 -- 1730},
  year      = {2008},
  language  = {en}
}
@article{HeuermannSadeghfam2007,
  author    = {Heuermann, Holger and Sadeghfam, Arash},
  title     = {On the design of multimode integrated circuits in multilayered processes / Sadeghfam, A. ; Heuermann, H.},
  series = {European Microwave Conference, 2007, 9-12 Oct. 2007},
  journal   = {European Microwave Conference, 2007, 9-12 Oct. 2007},
  isbn      = {978-2-87487-001-9},
  pages     = {516 -- 519},
  year      = {2007},
  language  = {en}
}