@phdthesis{Biewendt2022,
  author    = {Biewendt, Marcel},
  title     = {Socio-Economic challenges in sustainability and resource management},
  publisher = {Hungarian University of Agriculture and Life Sciences},
  pages     = {160 Seiten},
  year      = {2022},
  abstract  = {This dissertation uses in first stage a macroeconomic investigation to examine the dependence, influence and corruption of socio-economic development through effects of sustainability and resource management. The conducted research found that the state's dependence on its citizens decreases when the state's sources of revenue are largely detached and independent of the citizens' financial resources. In this case, financial resources are taxes and duties provided by the citizens. One possible consequence is the restriction of state investment in its citizens. Both the qualitative literature review and the quantitative data analysis revealed a negative correlation between socio-economic development and the resource economy's share of GDP for the period under study. The microeconomic investigation was primarily conducted through an intensive literature review. It was shown that the rebound effect as such is already very well researched. However, it also became clear that avoidance strategies for the rebound effect and links to sustainability initiatives are scarce or non-existent. The need for a redesign of the impact analysis with regard to technological innovations and their influence on resource consumption and resource management has become clear on the basis of the present study. Further, emerging and developing countries in particular, which will be confronted in the foreseeable future not only with the fundamental problems of resource abundance in the overall economic context, but also with the issues of their sustainable use, should be confronted with these problems as early as possible in order to find solutions in a timely manner.},
  language  = {de}
}
@misc{LippoldtRingbeckHuening2023,
  author    = {Lippoldt, Mario and Ringbeck, Thorsten and H{\"u}ning, Felix},
  title     = {Verfahren und System zur Erkennung von unerlaubten Fahrzeug-{\"U}berholvorg{\"a}ngen in einer {\"U}berholverbotszone eines Fahrwegs},
  year      = {2023},
  language  = {de}
}
@misc{BiewendtBlaschkeBoehnert2019,
  author    = {Biewendt, Marcel and Blaschke, Florian and B{\"o}hnert, Arno},
  title     = {The rebound effect: a critical and systematic review on the current state of affairs},
  series = {Abstracts of the International Conference on Sustainable Economy and Agriculture},
  journal   = {Abstracts of the International Conference on Sustainable Economy and Agriculture},
  editor    = {Koponicsne Gy{\"o}rke, Diana},
  publisher = {Universit{\"a}t Kaposv{\´a}r},
  address   = {Kaposv{\´a}r},
  isbn      = {978-615-5599-72-9},
  pages     = {101 -- 101},
  year      = {2019},
  language  = {en}
}
@article{BayerTemizArtmannDigeletal.2020,
  author    = {Bayer, Robin and Temiz Artmann, Ayseg{\"u}l and Digel, Ilya and Falkenstein, Julia and Artmann, Gerhard and Creutz, Till and Hescheler, J{\"u}rgen},
  title     = {Mechano-pharmacological testing of L-Type Ca²⁺ channel modulators via human vascular celldrum model},
  series = {Cellular Physiology and Biochemistry},
  volume    = {54},
  journal   = {Cellular Physiology and Biochemistry},
  publisher = {Cell Physiol Biochem Press},
  address   = {D{\"u}sseldorf},
  issn      = {1421-9778},
  doi       = {10.33594/000000225},
  pages     = {371 -- 383},
  year      = {2020},
  abstract  = {Background/Aims: This study aimed to establish a precise and well-defined working model, assessing pharmaceutical effects on vascular smooth muscle cell monolayer in-vitro. It describes various analysis techniques to determine the most suitable to measure the biomechanical impact of vasoactive agents by using CellDrum technology. Methods: The so-called CellDrum technology was applied to analyse the biomechanical properties of confluent human aorta muscle cells (haSMC) in monolayer. The cell generated tensions deviations in the range of a few N/m² are evaluated by the CellDrum technology. This study focuses on the dilative and contractive effects of L-type Ca²⁺ channel agonists and antagonists, respectively. We analyzed the effects of Bay K8644, nifedipine and verapamil. Three different measurement modes were developed and applied to determine the most appropriate analysis technique for the study purpose. These three operation modes are called, particular time mode" (PTM), "long term mode" (LTM) and "real-time mode" (RTM). Results: It was possible to quantify the biomechanical response of haSMCs to the addition of vasoactive agents using CellDrum technology. Due to the supplementation of 100nM Bay K8644, the tension increased approximately 10.6\% from initial tension maximum, whereas, the treatment with nifedipine and verapamil caused a significant decrease in cellular tension: 10nM nifedipine decreased the biomechanical stress around 6,5\% and 50nM verapamil by 2,8\%, compared to the initial tension maximum. Additionally, all tested measurement modes provide similar results while focusing on different analysis parameters. Conclusion: The CellDrum technology allows highly sensitive biomechanical stress measurements of cultured haSMC monolayers. The mechanical stress responses evoked by the application of vasoactive calcium channel modulators were quantified functionally (N/m²). All tested operation modes resulted in equal findings, whereas each mode features operation-related data analysis.},
  language  = {en}
}
@article{UysalCreutzFiratetal.2022,
  author    = {Uysal, Karya and Creutz, Till and Firat, Ipek Seda and Artmann, Gerhard and Teusch, Nicole and Temiz Artmann, Ayseg{\"u}l},
  title     = {Bio-functionalized ultra-thin, large-area and waterproof silicone membranes for biomechanical cellular loading and compliance experiments},
  series = {Polymers},
  volume    = {14},
  journal   = {Polymers},
  number    = {11},
  publisher = {MDPI},
  address   = {Basel},
  issn      = {2073-4360},
  pages     = {2213},
  year      = {2022},
  abstract  = {Biocompatibility, flexibility and durability make polydimethylsiloxane (PDMS) membranes top candidates in biomedical applications. CellDrum technology uses large area, <10 µm thin membranes as mechanical stress sensors of thin cell layers. For this to be successful, the properties (thickness, temperature, dust, wrinkles, etc.) must be precisely controlled. The following parameters of membrane fabrication by means of the Floating-on-Water (FoW) method were investigated: (1) PDMS volume, (2) ambient temperature, (3) membrane deflection and (4) membrane mechanical compliance. Significant differences were found between all PDMS volumes and thicknesses tested (p < 0.01). They also differed from the calculated values. At room temperatures between 22 and 26 °C, significant differences in average thickness values were found, as well as a continuous decrease in thicknesses within a 4 °C temperature elevation. No correlation was found between the membrane thickness groups (between 3-4 µm) in terms of deflection and compliance. We successfully present a fabrication method for thin bio-functionalized membranes in conjunction with a four-step quality management system. The results highlight the importance of tight regulation of production parameters through quality control. The use of membranes described here could also become the basis for material testing on thin, viscous layers such as polymers, dyes and adhesives, which goes far beyond biological applications.},
  language  = {en}
}
@article{RaffeisAdjeiKyeremehVroomenetal.2020,
  author    = {Raffeis, Iris and Adjei-Kyeremeh, Frank and Vroomen, Uwe and Westhoff, Elmar and Bremen, Sebastian and Hohoi, Alexandru and B{\"u}hrig-Polaczek, Andreas},
  title     = {Qualification of a Ni-Cu alloy for the laser powder bed fusion process (LPBF): Its microstructure and mechanical properties},
  series = {Applied Sciences},
  volume    = {10},
  journal   = {Applied Sciences},
  number    = {Art. 3401},
  publisher = {MDPI},
  address   = {Basel},
  issn      = {2076-3417},
  doi       = {10.3390/app10103401},
  pages     = {1 -- 15},
  year      = {2020},
  abstract  = {As researchers continue to seek the expansion of the material base for additive manufacturing, there is a need to focus attention on the Ni-Cu group of alloys which conventionally has wide industrial applications. In this work, the G-NiCu30Nb casting alloy, a variant of the Monel family of alloys with Nb and high Si content is, for the first time, processed via the laser powder bed fusion process (LPBF). Being novel to the LPBF processes, optimum LPBF parameters were determined, and hardness and tensile tests were performed in as-built conditions and after heat treatment at 1000 °C. Microstructures of the as-cast and the as-built condition were compared. Highly dense samples (99.8\% density) were achieved after varying hatch distance (80 µm and 140 µm) with scanning speed (550 mm/s-1500 mm/s). There was no significant difference in microhardness between varied hatch distance print sets. Microhardness of the as-built condition (247 HV0.2) exceeded the as-cast microhardness (179 HV0.2.). Tensile specimens built in vertical (V) and horizontal (H) orientations revealed degrees of anisotropy and were superior to conventionally reported figures. Post heat treatment increased ductility from 20\% to 31\% (V), as well as from 16\% to 25\% (H), while ultimate tensile strength (UTS) and yield strength (YS) were considerably reduced.},
  language  = {en}
}
@article{UysalFiratCreutzetal.2022,
  author    = {Uysal, Karya and Firat, Ipek Serat and Creutz, Till and Aydin, Inci Cansu and Artmann, Gerhard and Teusch, Nicole and Temiz Artmann, Ayseg{\"u}l},
  title     = {A novel in vitro wound healing assay using free-standing, ultra-thin PDMS membranes},
  series = {membranes},
  volume    = {2023},
  journal   = {membranes},
  number    = {13(1)},
  publisher = {MDPI},
  address   = {Basel},
  doi       = {10.3390/membranes13010022},
  pages     = {Artikel 22},
  year      = {2022},
  abstract  = {Advances in polymer science have significantly increased polymer applications in life sciences. We report the use of free-standing, ultra-thin polydimethylsiloxane (PDMS) membranes, called CellDrum, as cell culture substrates for an in vitro wound model. Dermal fibroblast monolayers from 28- and 88-year-old donors were cultured on CellDrums. By using stainless steel balls, circular cell-free areas were created in the cell layer (wounding). Sinusoidal strain of 1 Hz, 5\% strain, was applied to membranes for 30 min in 4 sessions. The gap circumference and closure rate of un-stretched samples (controls) and stretched samples were monitored over 4 days to investigate the effects of donor age and mechanical strain on wound closure. A significant decrease in gap circumference and an increase in gap closure rate were observed in trained samples from younger donors and control samples from older donors. In contrast, a significant decrease in gap closure rate and an increase in wound circumference were observed in the trained samples from older donors. Through these results, we propose the model of a cell monolayer on stretchable CellDrums as a practical tool for wound healing research. The combination of biomechanical cell loading in conjunction with analyses such as gene/protein expression seems promising beyond the scope published here.},
  language  = {en}
}
@inproceedings{KaschSchmidtEichleretal.2020,
  author    = {Kasch, Susanne and Schmidt, Thomas and Eichler, Fabian and Thurn, Laura and Jahn, Simon and Bremen, Sebastian},
  title     = {Solution approaches and process concepts for powder bed-based melting of glass},
  series = {Industrializing Additive Manufacturing. Proceedings of AMPA2020},
  booktitle = {Industrializing Additive Manufacturing. Proceedings of AMPA2020},
  publisher = {Springer},
  address   = {Cham},
  isbn      = {978-3-030-54333-4 (Print)},
  doi       = {10.1007/978-3-030-54334-1_7},
  pages     = {82 -- 95},
  year      = {2020},
  abstract  = {In the study, the process chain of additive manufacturing by means of powder bed fusion will be presented based on the material glass. In order to reliably process components additively, new concepts with different solutions were developed and investigated. Compared to established metallic materials, the properties of glass materials differ significantly. Therefore, the process control was adapted to the material glass in the investigations. With extensive parameter studies based on various glass powders such as borosilicate glass and quartz glass, scientifically proven results on powder bed fusion of glass are presented. Based on the determination of the particle properties with different methods, extensive investigations are made regarding the melting behavior of glass by means of laser beams. Furthermore, the experimental setup was steadily expanded. In addition to the integration of coaxial temperature measurement and regulation, preheating of the building platform is of major importance. This offers the possibility to perform 3D printing at the transformation temperatures of the glass materials. To improve the component's properties, the influence of a subsequent heat treatment was also investigated. The experience gained was incorporated into a new experimental system, which allows a much better exploration of the 3D printing of glass. Currently, studies are being conducted to improve surface texture, building accuracy, and geometrical capabilities using three-dimensional specimen. The contribution shows the development of research in the field of 3D printing of glass, gives an insight into the machine and process engineering as well as an outlook on the possibilities and applications.},
  language  = {en}
}
@inproceedings{WeissHeslenfeldSaeweetal.2022,
  author    = {Weiss, Christian and Heslenfeld, Jonas and Saewe, Jasmin Kathrin and Bremen, Sebastian and H{\"a}fner, Constantin Leon},
  title     = {Investigation on the influence of powder humidity in Laser Powder Bed Fusion (LPBF)},
  series = {Procedia CIRP 12th CIRP Conference on Photonic Technologies [LANE 2022]},
  volume    = {111},
  booktitle = {Procedia CIRP 12th CIRP Conference on Photonic Technologies [LANE 2022]},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {2212-8271},
  doi       = {10.1016/j.procir.2022.08.102},
  pages     = {115 -- 120},
  year      = {2022},
  abstract  = {In the Laser Powder Bed Fusion (LPBF) process, parts are built out of metal powder material by exposure of a laser beam. During handling operations of the powder material, several influencing factors can affect the properties of the powder material and therefore directly influence the processability during manufacturing. Contamination by moisture due to handling operations is one of the most critical aspects of powder quality. In order to investigate the influences of powder humidity on LPBF processing, four materials (AlSi10Mg, Ti6Al4V, 316L and IN718) are chosen for this study. The powder material is artificially humidified, subsequently characterized, manufactured into cubic samples in a miniaturized process chamber and analyzed for their relative density. The results indicate that the processability and reproducibility of parts made of AlSi10Mg and Ti6Al4V are susceptible to humidity, while IN718 and 316L are barely influenced.},
  language  = {en}
}
@article{TemizArtmannKurulgandemirciFıratetal.2021,
  author    = {Temiz Artmann, Ayseg{\"u}l and Kurulgan demirci, Eylem and F{\i}rat, Ipek Seda and Oflaz, Hakan and Artmann, Gerhard},
  title     = {Recombinant activated protein C (rhAPC) affects lipopolysaccharide-induced mechanical compliance changes and beat frequency of mESC-derived cardiomyocyte monolayers},
  series = {SHOCK},
  journal   = {SHOCK},
  publisher = {Wolters Kluwer},
  address   = {K{\"o}ln},
  issn      = {1540-0514},
  doi       = {10.1097/SHK.0000000000001845},
  year      = {2021},
  language  = {en}
}