@inproceedings{GoettenFingerHavermannetal.2019,
  author    = {G{\"o}tten, Falk and Finger, Felix and Havermann, Marc and Braun, Carsten and Marino, Matthew and Bil, Cees},
  title     = {A highly automated method for simulating airfoil characteristics at low Reynolds number using a RANS - transition approach},
  series = {Deutscher Luft- und Raumfahrtkongress - DLRK 2019. Darmstadt, Germany},
  booktitle = {Deutscher Luft- und Raumfahrtkongress - DLRK 2019. Darmstadt, Germany},
  doi       = {10.25967/490026},
  pages     = {1 -- 14},
  year      = {2019},
  language  = {en}
}
@article{WeberArentMuenchetal.2016,
  author    = {Weber, Tobias and Arent, Jan-Christoph and M{\"u}nch, Lukas and Duhovic, Miro and Balvers, Johannes M.},
  title     = {A fast method for the generation of boundary conditions for thermal autoclave simulation},
  series = {Composites Part A},
  volume    = {88},
  journal   = {Composites Part A},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {1359-835X},
  doi       = {10.1016/j.compositesa.2016.05.036},
  pages     = {216 -- 225},
  year      = {2016},
  abstract  = {Manufacturing process simulation enables the evaluation and improvement of autoclave mold concepts early in the design phase. To achieve a high part quality at low cycle times, the thermal behavior of the autoclave mold can be investigated by means of simulations. Most challenging for such a simulation is the generation of necessary boundary conditions. Heat-up and temperature distribution in an autoclave mold are governed by flow phenomena, tooling material and shape, position within the autoclave, and the chosen autoclave cycle. This paper identifies and summarizes the most important factors influencing mold heat-up and how they can be introduced into a thermal simulation. Thermal measurements are used to quantify the impact of the various parameters. Finally, the gained knowledge is applied to develop a semi-empirical approach for boundary condition estimation that enables a simple and fast thermal simulation of the autoclave curing process with reasonably high accuracy for tooling optimization.},
  language  = {en}
}
@article{SchmitzRoetertPischinger1988,
  author    = {Schmitz, G{\"u}nter and Roetert, J. and Pischinger, M.},
  title     = {A Fast Intelligent VMEbus System for Combustion Analysis in Engines},
  series = {19th [nineteenth] International Symposium on Automotive Technology \& [and] Automation : with particular reference to cell control and quality management systems for the manufacturing industries; Monte Carlo, 24. - 28. October 1988.},
  journal   = {19th [nineteenth] International Symposium on Automotive Technology \& [and] Automation : with particular reference to cell control and quality management systems for the manufacturing industries; Monte Carlo, 24. - 28. October 1988.},
  publisher = {Automotive Automation Ltd},
  address   = {Croydon},
  isbn      = {0947719229},
  pages     = {381 -- 391},
  year      = {1988},
  language  = {en}
}
@article{Harder1999,
  author    = {Harder, J{\"o}rn},
  title     = {A crystallographic model for the study of local deformation processes in polycrystals},
  series = {International journal of plasticity. 15 (1999), H. 6},
  journal   = {International journal of plasticity. 15 (1999), H. 6},
  isbn      = {0749-6419},
  pages     = {605 -- 624},
  year      = {1999},
  language  = {en}
}
@inproceedings{DigelDachwaldArtmannetal.2009,
  author    = {Digel, Ilya and Dachwald, Bernd and Artmann, Gerhard and Linder, Peter and Funke, O.},
  title     = {A concept of a probe for particle analysis and life detection in icy environments},
  year      = {2009},
  abstract  = {A melting probe equipped with autofluorescence-based detection system combined with a light scattering unit, and, optionally, with a microarray chip would be ideally suited to probe icy environments like Europa's ice layer as well as the polar ice layers of Earth and Mars for recent and extinct live.},
  subject      = {Sonde},
  language  = {en}
}
@inproceedings{KowalskiMcArdellBartelt2006,
  author    = {Kowalski, Julia and McArdell, B. W. and Bartelt, Perry},
  title     = {A comparison of two approaches to modeling multiphase gravity currents},
  series = {Geophysical Research Abstracts},
  volume    = {8},
  booktitle = {Geophysical Research Abstracts},
  year      = {2006},
  language  = {en}
}
@inproceedings{DachwaldSeboldtLoebetal.2007,
  author    = {Dachwald, Bernd and Seboldt, Wolfgang and Loeb, Horst W. and Schartner, Karl-Heinz},
  title     = {A comparison of SEP and NEP for a main belt asteroid sample return mission},
  series = {7th International Symposium on Launcher Technologies, Barcelona, Spain, 02-05 April 2007},
  booktitle = {7th International Symposium on Launcher Technologies, Barcelona, Spain, 02-05 April 2007},
  pages     = {1 -- 10},
  year      = {2007},
  abstract  = {Innovative interplanetary deep space missions, like a main belt asteroid sample return mission, require ever larger velocity increments (∆V s) and thus ever more demanding propulsion capabilities. Providing much larger exhaust velocities than chemical high-thrust systems, electric low-thrust space-propulsion systems can significantly enhance or even enable such high-energy missions. In 1995, a European-Russian Joint Study Group (JSG) presented a study report on "Advanced Interplanetary Missions Using Nuclear-Electric Propulsion" (NEP). One of the investigated reference missions was a sample return (SR) from the main belt asteroid (19) Fortuna. The envisaged nuclear power plant, Topaz-25, however, could not be realized and also the worldwide developments in space reactor hardware stalled. In this paper, we investigate, whether such a mission is also feasible using a solar electric propulsion (SEP) system and compare our SEP results to corresponding NEP results.},
  language  = {en}
}
@inproceedings{FingerdeVriesVosetal.2020,
  author    = {Finger, Felix and de Vries, Reynard and Vos, Roelof and Braun, Carsten and Bil, Cees},
  title     = {A comparison of hybrid-electric aircraft sizing methods},
  series = {AIAA Scitech 2020 Forum},
  booktitle = {AIAA Scitech 2020 Forum},
  doi       = {10.2514/6.2020-1006},
  pages     = {31 Seiten},
  year      = {2020},
  abstract  = {The number of case studies focusing on hybrid-electric aircraft is steadily increasing, since these configurations are thought to lead to lower operating costs and environmental impact than traditional aircraft. However, due to the lack of reference data of actual hybrid-electric aircraft, in most cases, the design tools and results are difficult to validate. In this paper, two independently developed approaches for hybrid-electric conceptual aircraft design are compared. An existing 19-seat commuter aircraft is selected as the conventional baseline, and both design tools are used to size that aircraft. The aircraft is then re-sized under consideration of hybrid-electric propulsion technology. This is performed for parallel, serial, and fully-electric powertrain architectures. Finally, sensitivity studies are conducted to assess the validity of the basic assumptions and approaches regarding the design of hybrid-electric aircraft. Both methods are found to predict the maximum take-off mass (MTOM) of the reference aircraft with less than 4\% error. The MTOM and payload-range energy efficiency of various (hybrid-) electric configurations are predicted with a maximum difference of approximately 2\% and 5\%, respectively. The results of this study confirm a correct formulation and implementation of the two design methods, and the data obtained can be used by researchers to benchmark and validate their design tools.},
  language  = {en}
}
@inproceedings{FunkeBeckmannAbanteriba2017,
  author    = {Funke, Harald and Beckmann, Nils and Abanteriba, Sylvester},
  title     = {A comparison of complex chemistry mechanisms for hydrogen methane blends based on the Sandia / Sydney Bluff-Body Flame HM1},
  series = {Proceedings of the Eleventh Asia-Pacific Conference on Combustion (ASPACC 2017), New South Wales, Australia, 10-14 December 2017},
  booktitle = {Proceedings of the Eleventh Asia-Pacific Conference on Combustion (ASPACC 2017), New South Wales, Australia, 10-14 December 2017},
  isbn      = {978-1-5108-5646-2},
  pages     = {262 -- 265},
  year      = {2017},
  language  = {en}
}
@article{GerhardtCooperWhitbreadetal.1985,
  author    = {Gerhardt, Hans Joachim and Cooper, K.-R. and Whitbread, R. and Gary, K.-P. (u.a.)},
  title     = {A comparison of aerodynamic drag measurements on model trucks in closed-jet and open-jet wind tunnels},
  pages     = {261 -- 274},
  year      = {1985},
  language  = {en}
}
@article{DachwaldTsinas1994,
  author    = {Dachwald, Bernd and Tsinas, L.},
  title     = {A combined neural and genetic learning algorithm / Tsinas, L. ; Dachwald, B.},
  series = {Proceedings of the First IEEE Conference on Evolutionary Computation, 1994. IEEE World Congress on Computational Intelligence.},
  journal   = {Proceedings of the First IEEE Conference on Evolutionary Computation, 1994. IEEE World Congress on Computational Intelligence.},
  address   = {Orlando, Fl},
  isbn      = {0-7803-1899-4},
  pages     = {770 -- 774},
  year      = {1994},
  language  = {en}
}
@article{KreyerMuellerEsch2020,
  author    = {Kreyer, J{\"o}rg and M{\"u}ller, Marvin and Esch, Thomas},
  title     = {A Calculation Methodology for Predicting Exhaust Mass Flows and Exhaust Temperature Profiles for Heavy-Duty Vehicles},
  series = {SAE International Journal of Commercial Vehicles},
  volume    = {13},
  journal   = {SAE International Journal of Commercial Vehicles},
  number    = {2},
  publisher = {SAE International},
  address   = {Warrendale, Pa.},
  issn      = {1946-3928},
  doi       = {10.4271/02-13-02-0009},
  pages     = {129 -- 143},
  year      = {2020},
  abstract  = {The predictive control of commercial vehicle energy management systems, such as vehicle thermal management or waste heat recovery (WHR) systems, are discussed on the basis of information sources from the field of environment recognition and in combination with the determination of the vehicle system condition. In this article, a mathematical method for predicting the exhaust gas mass flow and the exhaust gas temperature is presented based on driving data of a heavy-duty vehicle. The prediction refers to the conditions of the exhaust gas at the inlet of the exhaust gas recirculation (EGR) cooler and at the outlet of the exhaust gas aftertreatment system (EAT). The heavy-duty vehicle was operated on the motorway to investigate the characteristic operational profile. In addition to the use of road gradient profile data, an evaluation of the continuously recorded distance signal, which represents the distance between the test vehicle and the road user ahead, is included in the prediction model. Using a Fourier analysis, the trajectory of the vehicle speed is determined for a defined prediction horizon. To verify the method, a holistic simulation model consisting of several hierarchically structured submodels has been developed. A map-based submodel of a combustion engine is used to determine the EGR and EAT exhaust gas mass flows and exhaust gas temperature profiles. All simulation results are validated on the basis of the recorded vehicle and environmental data. Deviations from the predicted values are analyzed and discussed.},
  language  = {en}
}
@inproceedings{FunkeBeckmannKeinzetal.2021,
  author    = {Funke, Harald and Beckmann, Nils and Keinz, Jan and Horikawa, Atsushi},
  title     = {30 years of dry low NOx micromix combustor research for hydrogen-rich fuels: an overview of past and present activities},
  series = {Conference Proceedings Turbo Expo: Power for Land, Sea and Air, Volume 4B: Combustion, Fuels, and Emissions},
  booktitle = {Conference Proceedings Turbo Expo: Power for Land, Sea and Air, Volume 4B: Combustion, Fuels, and Emissions},
  publisher = {ASME},
  address   = {New York, NY},
  isbn      = {978-0-7918-8413-3},
  doi       = {10.1115/GT2020-16328},
  pages     = {14 Seiten},
  year      = {2021},
  abstract  = {The paper presents an overview of the past and present of low-emission combustor research with hydrogen-rich fuels at Aachen University of Applied Sciences. In 1990, AcUAS started developing the Dry-Low-NOx Micromix combustion technology. Micromix reduces NOx emissions using jet-in-crossflow mixing of multiple miniaturized fuel jets and combustor air with an inherent safety against flashback. At first, pure hydrogen as fuel was investigated with lab-scale applications. Later, Micromix prototypes were developed for the use in an industrial gas turbine Honeywell/Garrett GTCP-36-300, proving low NOx characteristics during real gas turbine operation, accompanied by the successful definition of safety laws and control system modifications. Further, the Micromix was optimized for the use in annular and can combustors as well as for fuel-flexibility with hydrogen-methane-mixtures and hydrogen-rich syngas qualities by means of extensive experimental and numerical simulations. In 2020, the latest Micromix application will be demonstrated in a commercial 2 MW-class gas turbine can-combustor with full-scale engine operation. The paper discusses the advances in Micromix research over the last three decades.},
  language  = {en}
}
@article{DachwaldOhndorf2007,
  author    = {Dachwald, Bernd and Ohndorf, A.},
  title     = {1st ACT Global Trajectory Optimisation Competition : Results found at DLR},
  series = {Acta Astronautica. 61 (2007), H. 9},
  journal   = {Acta Astronautica. 61 (2007), H. 9},
  isbn      = {0094-5765},
  pages     = {742 -- 752},
  year      = {2007},
  language  = {en}
}