@inproceedings{BueckingPfaffDirksmeier2018,
  author    = {B{\"u}cking, Henrik and Pfaff, Raphael and Dirksmeier, Roger},
  title     = {Sensor positioning and thermal model for condition monitoring of pressure gas reservoirs in vehicles},
  series = {Proceedings of the Fourth European Conference of the Prognostics and Health Management Society, Utrecht, Netherlands, 2018},
  booktitle = {Proceedings of the Fourth European Conference of the Prognostics and Health Management Society, Utrecht, Netherlands, 2018},
  pages     = {5 Seiten},
  year      = {2018},
  language  = {en}
}
@inproceedings{GaoBabilonPfaffetal.2018,
  author    = {Gao, H. and Babilon, Katharina and Pfaff, Raphael and Gan, F. and Reich, A.},
  title     = {Model of wheel-rail contact for sanding and adhesion enhancement},
  series = {Proceedings of the 11th International Conference on Contact Mechanics and Wear of Rail/wheel Systems, CM 2018},
  booktitle = {Proceedings of the 11th International Conference on Contact Mechanics and Wear of Rail/wheel Systems, CM 2018},
  isbn      = {978-946186963-0},
  pages     = {314 -- 321},
  year      = {2018},
  language  = {en}
}
@article{FranzenPindersPfaffetal.2018,
  author    = {Franzen, Julius and Pinders, Erik and Pfaff, Raphael and Enning, Manfred},
  title     = {RailCrowd's virtual fleets: Make most of your asset data},
  series = {Deine Bahn},
  journal   = {Deine Bahn},
  number    = {9},
  publisher = {Bahn-Fachverlag},
  address   = {Berlin},
  issn      = {0948-7263},
  pages     = {11 -- 13},
  year      = {2018},
  abstract  = {For smaller railway operators or those with a diverse fleet, it can be difficult to collect sufficient data to improve maintenance programs. At the same time, new rules such as entity in charge of maintenance - ECM - regulations impose an additional workload by requiring a dedicated maintenance management system and specific reports. The RailCrowd platform sets out to facilitate compliance with ECM and similar regulations while at the same time pooling anonymised fleet data across operators to form virtual fleets, providing greater data insights.},
  language  = {en}
}
@inproceedings{Pfaff2018,
  author    = {Pfaff, Raphael},
  title     = {Railway Challenge 2018 - Ein Wettbewerb f{\"u}r Parkbahn-Lokomotiven},
  series = {Deine Bahn},
  booktitle = {Deine Bahn},
  issn      = {0948-7263},
  pages     = {22 -- 24},
  year      = {2018},
  language  = {de}
}
@inproceedings{PfaffMelcherFranzen2018,
  author    = {Pfaff, Raphael and Melcher, Karin and Franzen, Julian},
  title     = {Rare event simulation to optimise maintenance intervals of safety critical redundant subsystems},
  series = {Proceedings of the European Conference of the PHM Society},
  volume    = {4},
  booktitle = {Proceedings of the European Conference of the PHM Society},
  number    = {1},
  pages     = {1 -- 6},
  year      = {2018},
  language  = {en}
}
@article{ZieburaBremenSchleifenbaumetal.2018,
  author    = {Ziebura, Dawid and Bremen, Sebastian and Schleifenbaum, Johannes Henrich and Gebhardt, Andreas},
  title     = {Machbarkeitsstudie zur Verarbeitung von nicht rostendem Stahl 1.4404 unter Verwendung einer Diodenlaser-basierten LPBF-Maschine mit kartesischem Achssystem},
  series = {RTejournal - Forum f{\"u}r Rapid Technologie},
  volume    = {15},
  journal   = {RTejournal - Forum f{\"u}r Rapid Technologie},
  issn      = {1614-0923},
  year      = {2018},
  language  = {de}
}
@article{SchmidtEnningPfaff2018,
  author    = {Schmidt, Bernd and Enning, Manfred and Pfaff, Raphael},
  title     = {G{\"u}terwagen 4.0 - Der G{\"u}terwagen f{\"u}r das Internet der Dinge Teil 3: Einf{\"u}hrungsszenarien f{\"u}r aktive, kommunikative G{\"u}terwagen},
  series = {ETR - Eisenbahntechnische Rundschau},
  volume    = {67},
  journal   = {ETR - Eisenbahntechnische Rundschau},
  number    = {5},
  publisher = {DVV Media Group},
  address   = {Hamburg},
  issn      = {0013-2845},
  pages     = {60 -- 64},
  year      = {2018},
  abstract  = {Wenn durch innovative, automatisierte G{\"u}terwagen betriebswirtschaftliche Vorteile nutzbar gemacht werden sollen, muss die Migration auf das neue System in sinnvollen Teilschritten unter Ber{\"u}cksichtigung der organisationellen und betrieblichen Vereinbarkeit vorgenommen werden. Eine stufenweise Migration mit Nachr{\"u}stbarkeit und Kompatibilit{\"a}t kann die optimale Ausstattungsvariante f{\"u}r die unterschiedlichen Betriebsszenarien sowie eine Steigerung der Wirtschaftlichkeit des Gesamtsystems bieten.},
  language  = {de}
}
@article{Thomas2018,
  author    = {Thomas, Axel},
  title     = {Technologiezentren in der Aachener Region - Retrospektiven und Perspektiven},
  series = {VM Verwaltung und Management},
  volume    = {24},
  journal   = {VM Verwaltung und Management},
  number    = {3},
  publisher = {Nomos},
  address   = {Baden-Baden},
  issn      = {0947-9856},
  doi       = {10.5771/0947-9856-2018-3-147},
  pages     = {147 -- 156},
  year      = {2018},
  language  = {de}
}
@article{Thomas2018,
  author    = {Thomas, Axel},
  title     = {Zielerreichungen der Technologie- und Gr{\"u}nderzentren aus Sicht der kommunalen Finanzwirtschaft - dargestellt am Beispiel der Aachener Region},
  series = {Der Gemeindehaushalt},
  volume    = {119},
  journal   = {Der Gemeindehaushalt},
  number    = {7},
  publisher = {Kohlhammer},
  address   = {Stuttgart},
  issn      = {0340-3645},
  pages     = {149 -- 155},
  year      = {2018},
  language  = {de}
}
@inproceedings{WiesenEngemannLimpertetal.2018,
  author    = {Wiesen, Patrick and Engemann, Heiko and Limpert, Nicolas and Kallweit, Stephan},
  title     = {Learning by Doing - Mobile Robotics in the FH Aachen ROS Summer School},
  series = {European Robotics Forum 2018, TRROS18 Workshop},
  booktitle = {European Robotics Forum 2018, TRROS18 Workshop},
  pages     = {47 -- 58},
  year      = {2018},
  language  = {en}
}
@inproceedings{ThurnGebhardt2018,
  author    = {Thurn, Laura and Gebhardt, Andreas},
  title     = {Strategy of Education on Materials for Students},
  series = {Conference Proceedings: „New Perspectives in Science Education"},
  booktitle = {Conference Proceedings: „New Perspectives in Science Education"},
  address   = {Florence, Italy},
  isbn      = {978-88-6292-976-9},
  pages     = {156 -- 161},
  year      = {2018},
  language  = {en}
}
@incollection{KlockeKatz2017,
  author    = {Klocke, Martina and Katz, Christiane},
  title     = {Heterogenit{\"a}t von MINT-Studierenden als Herausforderung},
  series = {Tagungsband zum 3. Symposium zur Hochschullehre in den MINT-F{\"a}chern},
  booktitle = {Tagungsband zum 3. Symposium zur Hochschullehre in den MINT-F{\"a}chern},
  publisher = {Technische Hochschule N{\"u}rnberg Georg Simon Ohm},
  address   = {N{\"u}rnberg},
  pages     = {31 -- 36},
  year      = {2017},
  language  = {de}
}
@incollection{Klocke2018,
  author    = {Klocke, Martina},
  title     = {Schulter an Schulter - Zusammenarbeit in einem differenzierten Hochschulsystem},
  series = {Lehre und Lehrentwicklung an Fachhochschulen - Festschrift f{\"u}r Prof. Dr. med. W. Huhn},
  booktitle = {Lehre und Lehrentwicklung an Fachhochschulen - Festschrift f{\"u}r Prof. Dr. med. W. Huhn},
  publisher = {Waxmann},
  address   = {M{\"u}nster},
  isbn      = {978-3-8309-3782-1},
  pages     = {75 -- 80},
  year      = {2018},
  language  = {de}
}
@article{PancContiuBocanetetal.2019,
  author    = {Panc, Nicolae and Contiu, Glad and Bocanet, Vlad and Thurn, Laura and Sabau, Emilia},
  title     = {The influence of cutting technology on surface wear hardness},
  series = {Academic Journal of Manufacturing Engineering},
  volume    = {17},
  journal   = {Academic Journal of Manufacturing Engineering},
  number    = {3},
  issn      = {1583-7904},
  pages     = {205 -- 210},
  year      = {2019},
  language  = {en}
}
@inproceedings{WiesenSchleser2019,
  author    = {Wiesen, Andreas and Schleser, Markus},
  title     = {Entwicklung einer Qualit{\"a}tssicherung f{\"u}r das Laserstrahlschweißen im Vakuum mittels Bildverarbeitung},
  series = {Große Schweißtechnische Tagung},
  booktitle = {Große Schweißtechnische Tagung},
  publisher = {DVS-Media},
  address   = {D{\"u}sseldorf},
  isbn      = {978-3-96144-066-5},
  pages     = {1 -- 6},
  year      = {2019},
  language  = {de}
}
@inproceedings{OttenGerhardsSchleseretal.2019,
  author    = {Otten, Christian and Gerhards, Benjamin and Schleser, Markus and Schwarz, A. and Gebhardt, Andreas},
  title     = {Innovative Laserschweißtechnologie f{\"u}r additiv gefertigte Bauteile},
  series = {Große Schweißtechnische Tagung},
  booktitle = {Große Schweißtechnische Tagung},
  publisher = {DVS-Media},
  address   = {D{\"u}sseldorf},
  isbn      = {978-3-96144-066-5},
  pages     = {150 -- 157},
  year      = {2019},
  language  = {de}
}
@incollection{FiedlerHennMelcher2015,
  author    = {Fiedler, Gerda and Henn, Gudrun and Melcher, Karin},
  title     = {ANPAK - Ein Anpassungskurs f{\"u}r Studienanf{\"a}nger in den Ingenieurwissenschaften},
  series = {Qualifizierung von Studierenden im Student-Life-Cycle. Tagungsband zum Mosbacher Tag der Lehre am 23.10.2014 /},
  booktitle = {Qualifizierung von Studierenden im Student-Life-Cycle. Tagungsband zum Mosbacher Tag der Lehre am 23.10.2014 /},
  editor    = {Morschheuser, Petra},
  publisher = {Duale Hochschule Baden-W{\"u}rttemberg (DHBW)},
  address   = {Mosbach},
  isbn      = {978-3-943656-02-2},
  pages     = {90 -- 93},
  year      = {2015},
  language  = {de}
}
@article{WilbringEnningPfaffetal.2020,
  author    = {Wilbring, Daniela and Enning, Manfred and Pfaff, Raphael and Schmidt, Bernd},
  title     = {Neue Perspektiven f{\"u}r die Bahn in der Produktions- und Distributionslogistik durch Prozessautomation},
  series = {ETR - Eisenbahntechnische Rundschau},
  volume    = {69},
  journal   = {ETR - Eisenbahntechnische Rundschau},
  number    = {3},
  issn      = {0013-2845},
  pages     = {15 -- 19},
  year      = {2020},
  language  = {de}
}
@article{CosmaKesslerGebhardtetal.2020,
  author    = {Cosma, Cosmin and Kessler, Julia and Gebhardt, Andreas and Campbell, Ian and Balc, Nicolae},
  title     = {Improving the Mechanical Strength of Dental Applications and Lattice Structures SLM Processed},
  series = {Materials},
  volume    = {13},
  journal   = {Materials},
  number    = {4},
  publisher = {MDPI},
  address   = {Basel},
  issn      = {1996-1944},
  doi       = {10.3390/ma13040905},
  pages     = {1 -- 18},
  year      = {2020},
  abstract  = {To manufacture custom medical parts or scaffolds with reduced defects and high mechanical characteristics, new research on optimizing the selective laser melting (SLM) parameters are needed. In this work, a biocompatible powder, 316L stainless steel, is characterized to understand the particle size, distribution, shape and flowability. Examination revealed that the 316L particles are smooth, nearly spherical, their mean diameter is 39.09 μm and just 10\% of them hold a diameter less than 21.18 μm. SLM parameters under consideration include laser power up to 200 W, 250-1500 mm/s scanning speed, 80 μm hatch spacing, 35 μm layer thickness and a preheated platform. The effect of these on processability is evaluated. More than 100 samples are SLM-manufactured with different process parameters. The tensile results show that is possible to raise the ultimate tensile strength up to 840 MPa, adapting the SLM parameters for a stable processability, avoiding the technological defects caused by residual stress. Correlating with other recent studies on SLM technology, the tensile strength is 20\% improved. To validate the SLM parameters and conditions established, complex bioengineering applications such as dental bridges and macro-porous grafts are SLM-processed, demonstrating the potential to manufacture medical products with increased mechanical resistance made of 316L.},
  language  = {en}
}
@article{EngelnMuellges1982,
  author    = {Engeln-M{\"u}llges, Gisela},
  title     = {Entartungsbedingungen f{\"u}r Gleitfl{\"a}chennomogramme und Nomographierbarkeitsbedingungen f{\"u}r Fluchtebenennomogramme},
  series = {ZAMM - Journal of Applied Mathematics and Mechanics / Zeitschrift f{\"u}r Angewandte Mathematik und Mechanik},
  volume    = {62},
  journal   = {ZAMM - Journal of Applied Mathematics and Mechanics / Zeitschrift f{\"u}r Angewandte Mathematik und Mechanik},
  number    = {2},
  issn      = {1521-4001},
  doi       = {10.1002/zamm.19820620203},
  pages     = {77 -- 93},
  year      = {1982},
  language  = {de}
}
@misc{Nordmann2022,
  type      = {Master Thesis},
  author    = {Nordmann, Alexander},
  title     = {Prozess{\"u}berwachung beim Werkzeugschleifen von WC-Co Hartmetallschaftfr{\"a}sern},
  publisher = {FH Aachen},
  address   = {Aachen},
  school      = {Fachhochschule Aachen},
  pages     = {xi, 54 Seiten},
  year      = {2022},
  language  = {de}
}
@masterthesis{Vu2022,
  type      = {Bachelor Thesis},
  author    = {Vu, Tuan Dat},
  title     = {Objekterkennung und Schienenerkennung in der Schienenfahrzeugtechnik},
  publisher = {FH Aachen},
  address   = {Aachen},
  school      = {Fachhochschule Aachen},
  pages     = {72 Seiten},
  year      = {2022},
  language  = {de}
}
@inproceedings{UlmerBraunChengetal.2021,
  author    = {Ulmer, Jessica and Braun, Sebastian and Cheng, Chi-Tsun and Dowey, Steve and Wollert, J{\"o}rg},
  title     = {Adapting augmented reality systems to the users' needs using gamification and error solving methods},
  series = {Procedia CIRP - 54th CIRP CMS 2021 - Towards Digitalized Manufacturing 4.0},
  volume    = {104},
  booktitle = {Procedia CIRP - 54th CIRP CMS 2021 - Towards Digitalized Manufacturing 4.0},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {2212-8271},
  doi       = {10.1016/j.procir.2021.11.024},
  pages     = {140 -- 145},
  year      = {2021},
  abstract  = {Animations of virtual items in AR support systems are typically predefined and lack interactions with dynamic physical environments. AR applications rarely consider users' preferences and do not provide customized spontaneous support under unknown situations. This research focuses on developing adaptive, error-tolerant AR systems based on directed acyclic graphs and error resolving strategies. Using this approach, users will have more freedom of choice during AR supported work, which leads to more efficient workflows. Error correction methods based on CAD models and predefined process data create individual support possibilities. The framework is implemented in the Industry 4.0 model factory at FH Aachen.},
  language  = {en}
}
@inproceedings{PfeifferBalcGebhardt2021,
  author    = {Pfeiffer, Johann and Balc, N. and Gebhardt, Andreas},
  title     = {Studie zur Untersuchung der Auswirkung von Fr{\"a}sbahnstrategien auf die Oberfl{\"a}chenqualit{\"a}t von mittels SLM gefertigten Metallteilen},
  series = {Tagungsband 21. Nachwuchswissenschaftler*innenkonferenz},
  booktitle = {Tagungsband 21. Nachwuchswissenschaftler*innenkonferenz},
  publisher = {Verlag Ernst-Abbe-Hochschule Jena},
  address   = {Jena},
  isbn      = {978-3-932886-36-2},
  pages     = {99 -- 102},
  year      = {2021},
  abstract  = {F{\"u}r die Herstellung von metallischen Bauteilen wird in der heutigen Zeit eine Vielzahl von Verfahren auf dem Markt angeboten. Dabei stehen die additiven im Wettbewerb zu den konventionellen Verfahren. Die erreichbaren Oberfl{\"a}chenqualit{\"a}ten der additiven sind nicht mit denen spanender Verfahren vergleichbar. F{\"u}r diesen Beitrag wurde analysiert, ob sich ein mittels Selektivem Laserschmelzen (SLM) additiv hergestellter Edelstahl hinsichtlich seiner Oberfl{\"a}chenqualit{\"a}t nach der Zerspanung von einem umgeformten konventionell hergestellten Edelstahl gleicher Sorte unterscheidet.},
  language  = {de}
}
@book{Feuerriegel2021,
  author    = {Feuerriegel, Uwe},
  title     = {W{\"a}rme{\"u}bertragung mit EXCEL und VBA: W{\"a}rmetechnische Berechnungen und Simulationen effektiv durchf{\"u}hren und professionell dokumentieren},
  publisher = {Springer Vieweg},
  address   = {Wiesbaden},
  isbn      = {978-3-658-35905-8},
  doi       = {10.1007/978-3-658-35906-5},
  pages     = {XX, 439 Seiten},
  year      = {2021},
  abstract  = {Dieses Lehrbuch vermittelt die Grundlagen der W{\"a}rme{\"u}bertragung sowie den Umgang mit EXCEL-VBA von der Erstellung von Makros bis zu benutzerdefinierten Funktionen. Es legt damit eine Basis f{\"u}r die schnelle und professionelle Durchf{\"u}hrung von Berechnungen und Simulationen. Die angeleitete Erstellung von Berechnungsmodulen mit EXCEL und VBA aus allen wichtigen Bereichen der W{\"a}rme{\"u}bertragung bildet den inhaltlichen Schwerpunkt. Dazu z{\"a}hlen die station{\"a}re W{\"a}rmeleitung und der station{\"a}re W{\"a}rmedurchgang, die instation{\"a}re W{\"a}rmeleitung, der W{\"a}rme{\"u}bergang bei freier und erzwungener Konvektion sowie die W{\"a}rmestrahlung und der W{\"a}rme{\"u}bergang beim Kondensieren und Sieden. Soweit sinnvoll und m{\"o}glich werden die Stoffwertekorrelationen und die Berechnungsvorschriften aus dem VDI-W{\"a}rmeatlas verwendet. F{\"u}r ausgew{\"a}hlte Anwendungen werden zudem komplexere Auslegungen und Simulationen von Prozessen der W{\"a}rme{\"u}bertragung sowie von W{\"a}rme{\"u}bertragern erstellt. Die Zielgruppen: Studierende in Bachelor- und Masterstudieng{\"a}ngen, Praktiker im Engineering},
  language  = {de}
}
@inproceedings{WeissHeslenfeldSaeweetal.2022,
  author    = {Weiss, Christian and Heslenfeld, Jonas and Saewe, Jasmin Kathrin and Bremen, Sebastian and H{\"a}fner, Constantin Leon},
  title     = {Investigation on the influence of powder humidity in Laser Powder Bed Fusion (LPBF)},
  series = {Procedia CIRP 12th CIRP Conference on Photonic Technologies [LANE 2022]},
  volume    = {111},
  booktitle = {Procedia CIRP 12th CIRP Conference on Photonic Technologies [LANE 2022]},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {2212-8271},
  doi       = {10.1016/j.procir.2022.08.102},
  pages     = {115 -- 120},
  year      = {2022},
  abstract  = {In the Laser Powder Bed Fusion (LPBF) process, parts are built out of metal powder material by exposure of a laser beam. During handling operations of the powder material, several influencing factors can affect the properties of the powder material and therefore directly influence the processability during manufacturing. Contamination by moisture due to handling operations is one of the most critical aspects of powder quality. In order to investigate the influences of powder humidity on LPBF processing, four materials (AlSi10Mg, Ti6Al4V, 316L and IN718) are chosen for this study. The powder material is artificially humidified, subsequently characterized, manufactured into cubic samples in a miniaturized process chamber and analyzed for their relative density. The results indicate that the processability and reproducibility of parts made of AlSi10Mg and Ti6Al4V are susceptible to humidity, while IN718 and 316L are barely influenced.},
  language  = {en}
}
@article{AbbasBalcBremenetal.2022,
  author    = {Abbas, Karim and Balc, Nicolae and Bremen, Sebastian and Skupin, Marco},
  title     = {Crystallization and aging behavior of polyetheretherketone PEEK within rapid tooling and rubber molding},
  series = {Journal of Manufacturing and Materials Processing},
  volume    = {6},
  journal   = {Journal of Manufacturing and Materials Processing},
  number    = {5},
  publisher = {MDPI},
  address   = {Basel},
  issn      = {2504-4494},
  doi       = {10.3390/jmmp6050093},
  pages     = {1 -- 12},
  year      = {2022},
  abstract  = {In times of short product life cycles, additive manufacturing and rapid tooling are important methods to make tool development and manufacturing more efficient. High-performance polymers are the key to mold production for prototypes and small series. However, the high temperatures during vulcanization injection molding cause thermal aging and can impair service life. The extent to which the thermal stress over the entire process chain stresses the material and whether it leads to irreversible material aging is evaluated. To this end, a mold made of PEEK is fabricated using fused filament fabrication and examined for its potential application. The mold is heated to 200 ◦C, filled with rubber, and cured. A differential scanning calorimetry analysis of each process step illustrates the crystallization behavior and first indicates the material resistance. It shows distinct cold crystallization regions at a build chamber temperature of 90 ◦C. At an ambient temperature above Tg, crystallization of 30\% is achieved, and cold crystallization no longer occurs. Additional tensile tests show a decrease in tensile strength after ten days of thermal aging. The steady decrease in recrystallization temperature indicates degradation of the additives. However, the tensile tests reveal steady embrittlement of the material due to increasing crosslinking.},
  language  = {en}
}
@article{EngemannCoenenDawaretal.2021,
  author    = {Engemann, Heiko and C{\"o}nen, Patrick and Dawar, Harshal and Du, Shengzhi and Kallweit, Stephan},
  title     = {A robot-assisted large-scale inspection of wind turbine blades in manufacturing using an autonomous mobile manipulator},
  series = {Applied Sciences},
  volume    = {11},
  journal   = {Applied Sciences},
  number    = {19},
  publisher = {MDPI},
  address   = {Basel},
  issn      = {2076-3417},
  doi       = {10.3390/app11199271},
  pages     = {1 -- 22},
  year      = {2021},
  abstract  = {Wind energy represents the dominant share of renewable energies. The rotor blades of a wind turbine are typically made from composite material, which withstands high forces during rotation. The huge dimensions of the rotor blades complicate the inspection processes in manufacturing. The automation of inspection processes has a great potential to increase the overall productivity and to create a consistent reliable database for each individual rotor blade. The focus of this paper is set on the process of rotor blade inspection automation by utilizing an autonomous mobile manipulator. The main innovations include a novel path planning strategy for zone-based navigation, which enables an intuitive right-hand or left-hand driving behavior in a shared human-robot workspace. In addition, we introduce a new method for surface orthogonal motion planning in connection with large-scale structures. An overall execution strategy controls the navigation and manipulation processes of the long-running inspection task. The implemented concepts are evaluated in simulation and applied in a real-use case including the tip of a rotor blade form.},
  language  = {en}
}
@masterthesis{Keller2022,
  type      = {Bachelor Thesis},
  author    = {Keller, Simon Mark},
  title     = {Risikoanalyse einer bordautonomen Schienenfahrzeugortung mittels GNSS},
  publisher = {FH Aachen},
  address   = {Aachen},
  school      = {Fachhochschule Aachen},
  pages     = {57 Seiten},
  year      = {2022},
  abstract  = {Bei Schienenfahrzeugen, die mit dem Zugsicherungssystem ETCS betrieben sind, wird die Odometrie durch eine diskrete Ortung mittels physischen Balisen zur{\"u}ckgesetzt. Diese Arbeit befasst sich mit der Innovation von virtuellen Balisen. Virtuelle Balisen, k{\"o}nnen eingesetzt werden, um physische, im Gleisbett montierte Balisen zu ersetzen. Durch den Einsatz von virtuellen Balisen soll der Infrastrukturausbau von ETCS vorangetrieben werden, indem sie als virtuelle Komponente auf Schienenfahrzeugen eingesetzt werden. Im Rahmen dieser Arbeit wird die Fragestellung beantwortet, ob eine bordautonome Zugortung mittels virtuellen Balisen in einem ausgew{\"a}hlten Szenario mit einem akzeptablen Risiko verbunden ist? Das Szenario besteht aus einem Schienenfahrzeug, welches mit dem Zugsicherungssystem ETCS Level 2 auf einer eingleisigen Nebenstrecke betreiben wird. Hierzu werden zun{\"a}chst die Grundlagen von ETCS und der satellitenbasierten Ortung erl{\"a}utert. Des Weiteren werden die Grundlagen des CSM Prozesses und der expliziten Risikoabsch{\"a}tzung eingef{\"u}hrt. Aufbauend auf diesen Grundlagen wird der CSM Prozess angewandt und dabei eine Systemdefinition mit den Schnittstellen des Systems zur Umwelt erstellt. Mit der Hazop-Methode werden die Gef{\"a}hrdungen der Schnittstellen erfasst und beurteilt. Die sicherheitsrelevanten Gef{\"a}hrdungen werden in einer FMEA bewertet. In der folgenden Diskussion werden sicherheitsrelevante Gef{\"a}hrdungen nochmals betrachtet. Das Ergebnis der Arbeit ist, dass im ausgew{\"a}hlten Szenario, unter der Verwendung der CSM-Prozesse und der industriell anerkannten Methoden Hazop und FMEA, die Integration der Board-autonomen-Ortung mit einem akzeptablen Risiko verbunden ist.},
  language  = {de}
}
@inproceedings{FiedlerGottschlichMuellerMelcher2021,
  author    = {Fiedler, Gerda and Gottschlich-M{\"u}ller, Birgit and Melcher, Karin},
  title     = {Online-Pr{\"u}fungen mit STACK Aufgaben},
  series = {Tagungsband ASIM Workshop STS/GMMS/EDU 2021},
  booktitle = {Tagungsband ASIM Workshop STS/GMMS/EDU 2021},
  editor    = {Liu-Henke, Xiaobo and Durak, Umut},
  publisher = {ARGESIM Verlag},
  address   = {Wien},
  isbn      = {978-3-901608-69-8},
  doi       = {10.11128/arep.45},
  pages     = {173 -- 178},
  year      = {2021},
  abstract  = {Wir stellen hier exemplarisch STACK Aufgaben vor, die frei von der Problematik sind, welche sich durch diverse Kommunikationswege und (webbasierte) Computer Algebra Systeme (CAS) ergibt. Daher sind sie insbesondere f{\"u}r eine Open-Book Online Pr{\"u}fung geeignet, da eine faire Pr{\"u}fungssituation gew{\"a}hrleistet werden kann.},
  language  = {de}
}
@inproceedings{EvansBraunUlmeretal.2022,
  author    = {Evans, Benjamin and Braun, Sebastian and Ulmer, Jessica and Wollert, J{\"o}rg},
  title     = {AAS implementations - current problems and solutions},
  series = {20th International Conference on Mechatronics - Mechatronika (ME)},
  booktitle = {20th International Conference on Mechatronics - Mechatronika (ME)},
  publisher = {IEEE},
  address   = {New York, NY},
  isbn      = {978-1-6654-1040-3},
  doi       = {10.1109/ME54704.2022.9982933},
  pages     = {6 Seiten},
  year      = {2022},
  abstract  = {The fourth industrial revolution presents a multitude of challenges for industries, one of which being the increased flexibility required of manufacturing lines as a result of increased consumer demand for individualised products. One solution to tackle this challenge is the digital twin, more specifically the standardised model of a digital twin also known as the asset administration shell. The standardisation of an industry wide communications tool is a critical step in enabling inter-company operations. This paper discusses the current state of asset administration shells, the frameworks used to host them and their problems that need to be addressed. To tackle these issues, we propose an event-based server capable of drastically reducing response times between assets and asset administration shells and a multi-agent system used for the orchestration and deployment of the shells in the field.},
  language  = {en}
}
@book{GebhardtKesslerThurn2016,
  author    = {Gebhardt, Andreas and Kessler, Julia and Thurn, Laura},
  title     = {3D-Drucken: Grundlagen und Anwendungen des additive manufacturing (AM)},
  edition   = {2., neu bearbeitete und erweiterte Auflage},
  publisher = {Hanser},
  address   = {M{\"u}nchen},
  isbn      = {978-3-446-44672-4},
  doi       = {10.3139/9783446448452},
  pages     = {XVI, 218 Seiten},
  year      = {2016},
  language  = {de}
}
@article{KosterScheidweilerTieves2016,
  author    = {Koster, Arie and Scheidweiler, Robert and Tieves, Martin},
  title     = {A flow based pruning scheme for enumerative equitable coloring algorithms},
  series = {A flow based pruning scheme for enumerative equitable coloring algorithms},
  journal   = {A flow based pruning scheme for enumerative equitable coloring algorithms},
  doi       = {10.48550/arXiv.1607.08754},
  pages     = {1 -- 30},
  year      = {2016},
  abstract  = {An equitable graph coloring is a proper vertex coloring of a graph G where the sizes of the color classes differ by at most one. The equitable chromatic number is the smallest number k such that G admits such equitable k-coloring. We focus on enumerative algorithms for the computation of the equitable coloring number and propose a general scheme to derive pruning rules for them: We show how the extendability of a partial coloring into an equitable coloring can be modeled via network flows. Thus, we obtain pruning rules which can be checked via flow algorithms. Computational experiments show that the search tree of enumerative algorithms can be significantly reduced in size by these rules and, in most instances, such naive approach even yields a faster algorithm. Moreover, the stability, i.e., the number of solved instances within a given time limit, is greatly improved. Since the execution of flow algorithms at each node of a search tree is time consuming, we derive arithmetic pruning rules (generalized Hall-conditions) from the network model. Adding these rules to an enumerative algorithm yields an even larger runtime improvement.},
  language  = {en}
}
@article{BeckenbachScheidweiler2016,
  author    = {Beckenbach, Isabel and Scheidweiler, Robert},
  title     = {Perfect ƒ-Matchings and ƒ-Factors in Hypergraphs - A Combinatorial Approach},
  series = {Discrete Mathematics},
  volume    = {240},
  journal   = {Discrete Mathematics},
  number    = {10},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {2192-7782},
  doi       = {10.1016/j.disc.2017.05.005},
  pages     = {2499 -- 2506},
  year      = {2016},
  abstract  = {We prove characterizations of the existence of perfect ƒ-matchings in uniform mengerian and perfect hypergraphs. Moreover, we investigate the ƒ-factor problem in balanced hypergraphs. For uniform balanced hypergraphs we prove two existence theorems with purely combinatorial arguments, whereas for non-uniform balanced hypergraphs we show that the ƒ-factor problem is NP-hard.},
  language  = {en}
}
@article{ScheidweilerTriesch2016,
  author    = {Scheidweiler, Robert and Triesch, Eberhard},
  title     = {A note on the duality between matchings and vertex covers in balanced hypergraphs},
  series = {Journal of Combinatorial Optimization},
  volume    = {32},
  journal   = {Journal of Combinatorial Optimization},
  number    = {2},
  publisher = {Springer},
  address   = {Berlin},
  issn      = {1573-2886},
  doi       = {10.1007/s10878-015-9887-5},
  pages     = {639 -- 644},
  year      = {2016},
  abstract  = {We present a new Min-Max theorem for an optimization problem closely connected to matchings and vertex covers in balanced hypergraphs. The result generalizes Kőnig's Theorem (Berge and Las Vergnas in Ann N Y Acad Sci 175:32-40, 1970; Fulkerson et al. in Math Progr Study 1:120-132, 1974) and Hall's Theorem (Conforti et al. in Combinatorica 16:325-329, 1996) for balanced hypergraphs.},
  language  = {en}
}
@article{KilicRaatschenKoerfgenetal.2017,
  author    = {Kilic, S. A. and Raatschen, Hans-J{\"u}rgen and K{\"o}rfgen, B. and Apaydin, N. M. and Astaneh-Asl, A.},
  title     = {FE Model of the Fatih Sultan Mehmet Suspension Bridge Using Thin Shell Finite Elements},
  series = {Arabian Journal for Science and Engineering},
  volume    = {42},
  journal   = {Arabian Journal for Science and Engineering},
  number    = {3},
  publisher = {Springer Nature},
  issn      = {2191-4281},
  doi       = {10.1007/s13369-016-2316-y},
  pages     = {1103 -- 1116},
  year      = {2017},
  abstract  = {This paper presents the results of an eigenvalue analysis of the Fatih Sultan Mehmet Bridge. A high-resolution finite element model was created directly from the available design documents. All physical properties of the structural components were included in detail, so no calibration to the measured data was necessary. The deck and towers were modeled with shell elements. A nonlinear static analysis was performed before the eigenvalue calculation. The calculated natural frequencies and corresponding mode shapes showed good agreement with the available measured ambient vibration data. The calculation of the effective modal mass showed that nine modes had single contributions higher than 5 \% of the total mass. They were in a frequency range up to 1.2 Hz. The comparison of the results for the torsional modes especially demonstrated the advantage of using thin shell finite elements over the beam modeling approach.},
  language  = {en}
}
@inproceedings{EngemannWiesenKallweitetal.2018,
  author    = {Engemann, Heiko and Wiesen, Patrick and Kallweit, Stephan and Deshpande, Harshavardhan and Schleupen, Josef},
  title     = {Autonomous mobile manipulation using ROS},
  series = {Advances in Service and Industrial Robotics},
  booktitle = {Advances in Service and Industrial Robotics},
  publisher = {Springer},
  address   = {Cham},
  isbn      = {978-3-319-61276-8},
  doi       = {10.1007/978-3-319-61276-8_43},
  pages     = {389 -- 401},
  year      = {2018},
  language  = {en}
}
@article{Pfaff2017,
  author    = {Pfaff, Raphael},
  title     = {Einsatz von offenen Onlinekursen in der Eisenbahnlehre},
  series = {Deine Bahn},
  journal   = {Deine Bahn},
  number    = {1},
  publisher = {Bahn-Fachverlag},
  address   = {Berlin},
  issn      = {0948-7263},
  pages     = {12 -- 16},
  year      = {2017},
  abstract  = {Eigene positive Erfahrungen mit Onlinekursen sowie die geringen Studierendenzahlen in der Pr{\"a}senzlehre gaben den Anstoß zu einem Experiment mit einem offenen Onlinekurs auf der Plattform Udemy. Die Erfahrungen sowohl bei der Erstellung und als auch im Lehrbetrieb waren positiv und f{\"u}hrten zu einer neuen Besch{\"a}ftigung mit Inhalten und Lernenden, getrieben durch die Anforderungen der Lernplattform.},
  language  = {de}
}
@inproceedings{MoshiriKahakPfaffGaebeletal.2017,
  author    = {Moshiri-Kahak, Amir and Pfaff, Raphael and G{\"a}bel, Markus and Reich, Alexander},
  title     = {Modellierung der Adh{\"a}sionsfl{\"a}che im Rad-Schiene-Kontakt unter Einsatz von reibwertverbessernden Mitteln},
  series = {15. Internationale Schienenfahrzeugtagung Rad Schiene 2017, Dresden, M{\"a}rz 2017},
  booktitle = {15. Internationale Schienenfahrzeugtagung Rad Schiene 2017, Dresden, M{\"a}rz 2017},
  pages     = {3 Seiten},
  year      = {2017},
  language  = {de}
}
@inproceedings{PfaffSchmidtEnning2017,
  author    = {Pfaff, Raphael and Schmidt, B. D. and Enning, Manfred},
  title     = {Towards inclusion of the freight rail system in the industrial internet of things - Wagon 4.0},
  series = {Stephenson Conference, London, March 2017},
  booktitle = {Stephenson Conference, London, March 2017},
  pages     = {1 -- 10},
  year      = {2017},
  language  = {en}
}
@article{Pfaff2017,
  author    = {Pfaff, Raphael},
  title     = {Apps f{\"u}r den G{\"u}terwagen? Wie der G{\"u}terwagen 4.0 die effiziente Integration der G{\"u}terbahn in ERTMS erm{\"o}glicht},
  series = {Ingenieurspiegel},
  journal   = {Ingenieurspiegel},
  number    = {2},
  pages     = {1 -- 2},
  year      = {2017},
  language  = {de}
}
@inproceedings{PfaffMoshiriReichetal.2017,
  author    = {Pfaff, Raphael and Moshiri, Amir and Reich, Alexander and G{\"a}bel, Markus},
  title     = {Modelling of the effect of sanding on the wheel-rail adhesion area},
  series = {First International Conference on Rail Transportation},
  booktitle = {First International Conference on Rail Transportation},
  pages     = {1 -- 7},
  year      = {2017},
  language  = {en}
}
@inproceedings{ShahidiPfaffEnning2017,
  author    = {Shahidi, Parham and Pfaff, Raphael and Enning, Manfred},
  title     = {The connected wagon - a concept for the integration of vehicle side sensors and actors with cyber physical representation for condition based maintenance},
  series = {First International Conference on Rail Transportation},
  booktitle = {First International Conference on Rail Transportation},
  pages     = {1 -- 8},
  year      = {2017},
  language  = {en}
}
@inproceedings{PfaffShahidiEnning2017,
  author    = {Pfaff, Raphael and Shahidi, Parham and Enning, Manfred},
  title     = {Connected freight rail rolling stock: a modular approach integrating sensors, actors and cyber physical systems for operational advantages and condition based maintenance},
  series = {Asia-Pacific Conference of the Prognostics and Health Management Society},
  booktitle = {Asia-Pacific Conference of the Prognostics and Health Management Society},
  pages     = {1 -- 7},
  year      = {2017},
  language  = {en}
}
@inproceedings{Pfaff2017,
  author    = {Pfaff, Raphael},
  title     = {Analysis of Big Data Streams to obtain Braking Reliability Information for Train Protection systems},
  series = {Asia-Pacific Conference of the Prognostics and Health Management Society},
  booktitle = {Asia-Pacific Conference of the Prognostics and Health Management Society},
  pages     = {1 -- 7},
  year      = {2017},
  language  = {en}
}
@inproceedings{FateriGebhardtRenftle2015,
  author    = {Fateri, Miranda and Gebhardt, Andreas and Renftle, Georg},
  title     = {Additive manufacturing of drainage segments for cooling system of crucible melting furnaces},
  series = {Advanced Processing and Manufacturing Technologies for Structural and Multifunctional Materials II, International Symposium on Advanced Processing and Manufacturing Technologies for Structural and Multifunctional Materials, ICACC 15, 39th International Conference on Advanced Ceramics and Composites, Daytona Beach, FL, US, Jan 25-30, 2015},
  booktitle = {Advanced Processing and Manufacturing Technologies for Structural and Multifunctional Materials II, International Symposium on Advanced Processing and Manufacturing Technologies for Structural and Multifunctional Materials, ICACC 15, 39th International Conference on Advanced Ceramics and Composites, Daytona Beach, FL, US, Jan 25-30, 2015},
  publisher = {Wiley},
  address   = {Hoboken},
  issn      = {0196-6219},
  doi       = {10.1002/9781119211662.ch14},
  pages     = {123 -- 131},
  year      = {2015},
  language  = {en}
}
@inproceedings{UlmerBraunWollert2018,
  author    = {Ulmer, Jessica and Braun, Sebastian and Wollert, J{\"o}rg},
  title     = {Generische IoT Adapter f{\"u}r semantische Maschinenschnittstellen},
  series = {Internet of Things - vom Sensor bis zur Cloud},
  booktitle = {Internet of Things - vom Sensor bis zur Cloud},
  pages     = {1 -- 5},
  year      = {2018},
  language  = {de}
}
@inproceedings{UlmerLaiChengetal.2019,
  author    = {Ulmer, Jessica and Lai, Chow Yin and Cheng, Chi-Tsun and Wollert, J{\"o}rg},
  title     = {Integration von VR und AR in Produktlebenszyklen - Eine {\"U}bersicht {\"u}ber die Nutzung virtueller Technologien im industriellen Umfeld},
  series = {Automation 2019},
  booktitle = {Automation 2019},
  pages     = {1 -- 12},
  year      = {2019},
  language  = {de}
}
@inproceedings{UlmerBraunLaietal.2019,
  author    = {Ulmer, Jessica and Braun, Sebastian and Lai, Chow Yin and Cheng, Chi-Tsun and Wollert, J{\"o}rg},
  title     = {Generic integration of VR and AR in product lifecycles based on CAD models},
  series = {Proceedings of The 23rd World Multi-Conference on Systemics, Cybernetics and Informatics: WMSCI 2019},
  booktitle = {Proceedings of The 23rd World Multi-Conference on Systemics, Cybernetics and Informatics: WMSCI 2019},
  year      = {2019},
  language  = {en}
}
@inproceedings{EngemannBadriWenningetal.2019,
  author    = {Engemann, Heiko and Badri, Sriram and Wenning, Marius and Kallweit, Stephan},
  title     = {Implementation of an Autonomous Tool Trolley in a Production Line},
  series = {Advances in Service and Industrial Robotics. RAAD 2019. Advances in Intelligent Systems and Computing, vol 980},
  booktitle = {Advances in Service and Industrial Robotics. RAAD 2019. Advances in Intelligent Systems and Computing, vol 980},
  publisher = {Springer},
  address   = {Cham},
  isbn      = {978-3-030-19648-6},
  doi       = {10.1007/978-3-030-19648-6_14},
  pages     = {117 -- 125},
  year      = {2019},
  language  = {en}
}
@article{SchwarzGebhardtSchleseretal.2019,
  author    = {Schwarz, Alexander and Gebhardt, Andreas and Schleser, Markus and Popoola, Patricia},
  title     = {New Welding Joint Geometries Manufactured by Powder Bed Fusion from 316L},
  series = {Materials Performance and Characterization 8},
  journal   = {Materials Performance and Characterization 8},
  number    = {in press},
  issn      = {2379-1365},
  doi       = {10.1520/MPC20180096},
  year      = {2019},
  language  = {en}
}
@article{BucurLazarescuPopetal.2019,
  author    = {Bucur, Alexandru and Lazarescu, Lucian and Pop, Grigore Marian and Achimas, Gheorghe and Gebhardt, Andreas},
  title     = {Tribological performance of biodegradable lubricants under different surface roughness of tools},
  series = {Academic Journal of Manufacturing Engineering},
  volume    = {17},
  journal   = {Academic Journal of Manufacturing Engineering},
  number    = {1},
  issn      = {1583-7904},
  pages     = {172 -- 178},
  year      = {2019},
  language  = {en}
}
@inproceedings{UlmerWollertChengetal.2020,
  author    = {Ulmer, Jessica and Wollert, J{\"o}rg and Cheng, C. and Dowey, S.},
  title     = {Enterprise Gamification f{\"u}r produzierende mittelst{\"a}ndische Unternehmen},
  series = {Automation 2020 : Shaping Automation for our Future},
  booktitle = {Automation 2020 : Shaping Automation for our Future},
  publisher = {VDI-Verlag},
  address   = {D{\"u}sseldorf},
  isbn      = {978-3-18-092375-8},
  doi       = {10.51202/9783181023754-157},
  pages     = {157 -- 165},
  year      = {2020},
  abstract  = {Die fortschreitende Digitalisierung und Globalisierung fordert von den Unternehmen eine erh{\"o}hte Flexibilit{\"a}t und Anpassungsf{\"a}higkeit. Um dies zu erreichen, sind qualifizierte und engagierte Mitarbeiter/-innen unabdingbar. Gamification bietet die M{\"o}glichkeit, Besch{\"a}ftigte individuell in ihren T{\"a}tigkeiten zu unterst{\"u}tzen und mittels Feedbackmechanismen zu motivieren. In dieser Arbeit wird ein Gamification Konzept bestehend aus einem intelligenten Arbeitsplatz, einer Wissensdatenbank und einer Gamification Plattform vorgestellt, welches an bestehende Produktionsumgebungen adaptiert werden kann. Das Konzept wird am Beispiel der Longboardproduktion in der Industrie 4.0 Modellfabrik der FH Aachen implementiert und evaluiert.},
  language  = {de}
}
@article{PfaffGidaszewskiSchmidt2020,
  author    = {Pfaff, Raphael and Gidaszewski, Lars and Schmidt, Bernd},
  title     = {Ber{\"u}cksichtigung von No Fault Found im Diagnose- und Instandhaltungssystem von Schienenfahrzeugen},
  series = {ETR - Eisenbahntechnische Rundschau},
  journal   = {ETR - Eisenbahntechnische Rundschau},
  number    = {5},
  publisher = {DVV Media Group},
  address   = {Hamburg},
  issn      = {0013-2845},
  pages     = {56 -- 59},
  year      = {2020},
  abstract  = {Intermittierende und nicht reproduzierbare Fehler, auch als No Fault Found bezeichnet, treten in praktisch allen Bereichen auf und sorgen f{\"u}r hohe Kosten. Diese sind h{\"a}ufig auf unpr{\"a}zise Fehlerbeschreibungen zur{\"u}ckzuf{\"u}hren. Im vorliegenden Beitrag werden Anpassungen der Vorgehensweise bei der Entwicklung und Anpassungen des Diagnosesystems vorgeschlagen.},
  language  = {de}
}
@article{FrankoDuKallweitetal.2020,
  author    = {Franko, Josef and Du, Shengzhi and Kallweit, Stephan and Duelberg, Enno Sebastian and Engemann, Heiko},
  title     = {Design of a Multi-Robot System for Wind Turbine Maintenance},
  series = {Energies},
  volume    = {13},
  journal   = {Energies},
  number    = {10},
  publisher = {MDPI},
  address   = {Basel},
  issn      = {1996-1073},
  doi       = {10.3390/en13102552},
  pages     = {Article 2552},
  year      = {2020},
  abstract  = {The maintenance of wind turbines is of growing importance considering the transition to renewable energy. This paper presents a multi-robot-approach for automated wind turbine maintenance including a novel climbing robot. Currently, wind turbine maintenance remains a manual task, which is monotonous, dangerous, and also physically demanding due to the large scale of wind turbines. Technical climbers are required to work at significant heights, even in bad weather conditions. Furthermore, a skilled labor force with sufficient knowledge in repairing fiber composite material is rare. Autonomous mobile systems enable the digitization of the maintenance process. They can be designed for weather-independent operations. This work contributes to the development and experimental validation of a maintenance system consisting of multiple robotic platforms for a variety of tasks, such as wind turbine tower and rotor blade service. In this work, multicopters with vision and LiDAR sensors for global inspection are used to guide slower climbing robots. Light-weight magnetic climbers with surface contact were used to analyze structure parts with non-destructive inspection methods and to locally repair smaller defects. Localization was enabled by adapting odometry for conical-shaped surfaces considering additional navigation sensors. Magnets were suitable for steel towers to clamp onto the surface. A friction-based climbing ring robot (SMART— Scanning, Monitoring, Analyzing, Repair and Transportation) completed the set-up for higher payload. The maintenance period could be extended by using weather-proofed maintenance robots. The multi-robot-system was running the Robot Operating System (ROS). Additionally, first steps towards machine learning would enable maintenance staff to use pattern classification for fault diagnosis in order to operate safely from the ground in the future.},
  language  = {en}
}
@article{RaffeisAdjeiKyeremehVroomenetal.2020,
  author    = {Raffeis, Iris and Adjei-Kyeremeh, Frank and Vroomen, Uwe and Westhoff, Elmar and Bremen, Sebastian and Hohoi, Alexandru and B{\"u}hrig-Polaczek, Andreas},
  title     = {Qualification of a Ni-Cu alloy for the laser powder bed fusion process (LPBF): Its microstructure and mechanical properties},
  series = {Applied Sciences},
  volume    = {10},
  journal   = {Applied Sciences},
  number    = {Art. 3401},
  publisher = {MDPI},
  address   = {Basel},
  issn      = {2076-3417},
  doi       = {10.3390/app10103401},
  pages     = {1 -- 15},
  year      = {2020},
  abstract  = {As researchers continue to seek the expansion of the material base for additive manufacturing, there is a need to focus attention on the Ni-Cu group of alloys which conventionally has wide industrial applications. In this work, the G-NiCu30Nb casting alloy, a variant of the Monel family of alloys with Nb and high Si content is, for the first time, processed via the laser powder bed fusion process (LPBF). Being novel to the LPBF processes, optimum LPBF parameters were determined, and hardness and tensile tests were performed in as-built conditions and after heat treatment at 1000 °C. Microstructures of the as-cast and the as-built condition were compared. Highly dense samples (99.8\% density) were achieved after varying hatch distance (80 µm and 140 µm) with scanning speed (550 mm/s-1500 mm/s). There was no significant difference in microhardness between varied hatch distance print sets. Microhardness of the as-built condition (247 HV0.2) exceeded the as-cast microhardness (179 HV0.2.). Tensile specimens built in vertical (V) and horizontal (H) orientations revealed degrees of anisotropy and were superior to conventionally reported figures. Post heat treatment increased ductility from 20\% to 31\% (V), as well as from 16\% to 25\% (H), while ultimate tensile strength (UTS) and yield strength (YS) were considerably reduced.},
  language  = {en}
}
@inproceedings{BraunChengDoweyetal.2020,
  author    = {Braun, Sebastian and Cheng, Chi-Tsun and Dowey, Steve and Wollert, J{\"o}rg},
  title     = {Survey on Security Concepts to Adapt Flexible Manufacturing and Operations Management based upon Multi-Agent Systems},
  series = {2020 IEEE 29th International Symposium on Industrial Electronics (ISIE), Proceedings},
  booktitle = {2020 IEEE 29th International Symposium on Industrial Electronics (ISIE), Proceedings},
  publisher = {IEEE},
  address   = {New York, NY},
  doi       = {10.1109/ISIE45063.2020.9152210},
  pages     = {5 Seiten},
  year      = {2020},
  abstract  = {The increasing digitalization brings new opportunities but also puts new challenges to modern industrial systems. Software agents are one of the key technologies towards self-optimizing factories and are currently used to address the needs of cyber-physical production systems (CPPS). However their interplay in industrial settings needs to be understood better.This paper focusses on securing a cloud infrastructure for multi-agent systems for industrial sites. An industrial site contains multiple production processes that need to communicate with each other and each physical resource is abstracted with a software agent. This volatile architecture needs to be managed and protected from manipulation. The proposed infrastructure presents a security concept for TCP/IP communication between agents, machines, and external networks. It is based on open-source software and tested on a three-node edge cloud controlling a model-plant.},
  language  = {en}
}
@article{KunkelGebhardtMpofuetal.2019,
  author    = {Kunkel, Maximilian Hugo and Gebhardt, Andreas and Mpofu, Khumbulani and Kallweit, Stephan},
  title     = {Quality assurance in metal powder bed fusion via deep-learning-based image classification},
  series = {Rapid Prototyping Journal},
  volume    = {26},
  journal   = {Rapid Prototyping Journal},
  number    = {2},
  issn      = {1355-2546},
  doi       = {10.1108/RPJ-03-2019-0066},
  pages     = {259 -- 266},
  year      = {2019},
  language  = {en}
}
@article{UlmerBraunChengetal.2020,
  author    = {Ulmer, Jessica and Braun, Sebastian and Cheng, Chi-Tsun and Dowey, Steve and Wollert, J{\"o}rg},
  title     = {Human-Centered Gamification Framework for Manufacturing Systems},
  series = {Procedia CIRP},
  volume    = {93},
  journal   = {Procedia CIRP},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {2212-8271},
  doi       = {10.1016/j.procir.2020.04.076},
  pages     = {670 -- 675},
  year      = {2020},
  abstract  = {While bringing new opportunities, the Industry 4.0 movement also imposes new challenges to the manufacturing industry and all its stakeholders. In this competitive environment, a skilled and engaged workforce is a key to success. Gamification can generate valuable feedbacks for improving employees' engagement and performance. Currently, Gamification in workspaces focuses on computer-based assignments and training, while tasks that require manual labor are rarely considered. This research provides an overview of Enterprise Gamification approaches and evaluates the challenges. Based on that, a skill-based Gamification framework for manual tasks is proposed, and a case study in the Industry 4.0 model factory is shown.},
  language  = {en}
}
@article{UlmerBraunChengetal.2022,
  author    = {Ulmer, Jessica and Braun, Sebastian and Cheng, Chi-Tsun and Dowey, Steve and Wollert, J{\"o}rg},
  title     = {Gamification of virtual reality assembly training: Effects of a combined point and level system on motivation and training results},
  series = {International Journal of Human-Computer Studies},
  volume    = {165},
  journal   = {International Journal of Human-Computer Studies},
  number    = {Art. No. 102854},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {1071-5819},
  doi       = {10.1016/j.ijhcs.2022.102854},
  year      = {2022},
  abstract  = {Virtual Reality (VR) offers novel possibilities for remote training regardless of the availability of the actual equipment, the presence of specialists, and the training locations. Research shows that training environments that adapt to users' preferences and performance can promote more effective learning. However, the observed results can hardly be traced back to specific adaptive measures but the whole new training approach. This study analyzes the effects of a combined point and leveling VR-based gamification system on assembly training targeting specific training outcomes and users' motivations. The Gamified-VR-Group with 26 subjects received the gamified training, and the Non-Gamified-VR-Group with 27 subjects received the alternative without gamified elements. Both groups conducted their VR training at least three times before assembling the actual structure. The study found that a level system that gradually increases the difficulty and error probability in VR can significantly lower real-world error rates, self-corrections, and support usages. According to our study, a high error occurrence at the highest training level reduced the Gamified-VR-Group's feeling of competence compared to the Non-Gamified-VR-Group, but at the same time also led to lower error probabilities in real-life. It is concluded that a level system with a variable task difficulty should be combined with carefully balanced positive and negative feedback messages. This way, better learning results, and an improved self-evaluation can be achieved while not causing significant impacts on the participants' feeling of competence.},
  language  = {en}
}
@masterthesis{Schnitzler2022,
  type      = {Bachelor Thesis},
  author    = {Schnitzler, Nora},
  title     = {Identifikation und Bewertung geeigneter Mikrostrukturierungen zum Schutz von Biohybridbeschichtungen von Zahnimplantaten vor Abrasion beim Z{\"a}hneputzen},
  publisher = {FH Aachen},
  address   = {Aachen},
  school      = {Fachhochschule Aachen},
  pages     = {67 S.},
  year      = {2022},
  abstract  = {Die Oberfl{\"a}chen dentaler Implantate sind definiert durch eine raue Oberfl{\"a}che, um die Integration in den menschlichen Knochen zu optimieren. Entz{\"u}ndungen des umgebenden Zahnfleisches z{\"a}hlen dabei zu den h{\"a}ufigsten Komplikationen nach einer Implantation. Diese Entz{\"u}ndungen entstehen haupts{\"a}chlich durch bakterielle Infektionen des Weichgewebes an der Implantations-Stelle. Die raue Oberfl{\"a}che tr{\"a}gt jedoch zu einer solchen Infektion bei. Da der Implantat-Kopf zum Teil aus dem Knochen herausragt, erfolgt beispielsweise beim Z{\"a}hneputzen eine Freilegung der Implantat-Oberfl{\"a}che. Die durch die Rauheit vergr{\"o}ßerte Oberfl{\"a}che bietet dabei ideale Voraussetzungen f{\"u}r eine Bakterienansiedlung. In der aktuellen Forschung steht die Entwicklung einer Oberfl{\"a}che im Vordergrund, die eine antibakterielle Funktionalisierung erzeugt. Diese verhindert die Bakterienansiedlung und wirkt einer Entz{\"u}ndung entgegen. Um die Beschichtung vor Verschleiß zu sch{\"u}tzen und ihre Lebensdauer der antibakteriellen Wirkung zu erh{\"o}hen, ist es m{\"o}glich die Oberfl{\"a}che mit einer Mikrostruktur zu versehen. Das Ziel der vorliegenden Arbeit ist die Identifikation geeigneter Mikrostrukturierungen, die der antibakteriellen Beschichtung einen optimalen Schutz vor Verschleiß bieten. Am Beispiel von Titan-Zahnimplantaten wird der Schutz der aufgetragenen Biohybridbeschichtung gegen abrasiven Verschleiß untersucht. Im Vorfeld wird eine Analyse der fertigungstechnischen M{\"o}glichkeiten mit Blick auf dentale Implantate und Mikrostrukturen durchgef{\"u}hrt, um das ein passendes Verfahren zu identifizieren. Die Analogiebauteile als Probenk{\"o}rper werden, mithilfe des zuvor ausgew{\"a}hlten Verfahrens, mit verschiedenen Mikrostrukturen versehen. Im Rahmen einer Versuchsdurchf{\"u}hrung, die die mechanische Belastung bei einem Zahnputzdurchgang imitiert, werden die verschiedenen Mikrostrukturen auf ihre Eignung f{\"u}r diese Anwendung {\"u}berpr{\"u}ft. Ein Vorversuch dient zur Identifizierung eines geeigneten Ankerpeptids, welches den bindenden Bestandteil der Biohybridbeschichtung darstellt. Aus drei zuvor ausgew{\"a}hlten Ankerpeptiden wird das mit der besten Adh{\"a}sionsf{\"a}higkeit herausgestellt. Im finalen Versuchsdurchlauf wird das Ankerpeptid auf die Oberfl{\"a}chen, die mit den Mikrostrukturen versehen sind, aufgetragen. Dabei ist das Ziel eine Mikrostruktur herauszustellen, die den h{\"o}chstm{\"o}glichen Schutz bietet. Durch eine Fluoreszenzpr{\"u}fung mithilfe eines Flourescence Plate Readers wird jede Kombination nach den Belastungsversuchen auf den Restanteil der Beschichtung {\"u}berpr{\"u}ft. Das Ergebnis stellt eine Mikrostruktur dar, die den bestm{\"o}glichen Schutz bietet. Dies ist erkennbar durch den h{\"o}chsten Anteil an Restbeschichtung. Eine Strukturierung mit sogenannten Micro-Grooves in Kombination mit dem MacHis-Ankerpeptid erzielte in der Analyse der Belastungssimulationen die besten Ergebnisse bez{\"u}glich des Schutzes der Beschichtung. Durch die Versuche best{\"a}tigte sich eine weitere Annahme. Die Strukturierung der Oberfl{\"a}che erzielt einen deutlich h{\"o}heren Schutz im Vergleich zu einer unstrukturierten Oberfl{\"a}che. Zudem hat sich herausgestellt, dass eine Beschichtung mit dem sogenannten PEO-Verfahren eine deutlich gr{\"o}ßere Adh{\"a}sion der Biohybridbeschichtung erzielt. Dies wird jedoch Thema weiterf{\"u}hrender Forschungen sein und kein Bestandteil der vorliegenden Arbeit.},
  language  = {de}
}
@article{PfaffEnningSutter2022,
  author    = {Pfaff, Raphael and Enning, Manfred and Sutter, Stefan},
  title     = {A risk‑based approach to automatic brake tests for rail freight service: incident analysis and realisation concept},
  series = {SN Applied Sciences},
  volume    = {4},
  journal   = {SN Applied Sciences},
  number    = {4},
  publisher = {Springer},
  address   = {Cham},
  issn      = {2523-3971},
  doi       = {10.1007/s42452-022-05007-x},
  pages     = {1 -- 14},
  year      = {2022},
  abstract  = {This study reviews the practice of brake tests in freight railways, which is time consuming and not suitable to detect certain failure types. Public incident reports are analysed to derive a reasonable brake test hardware and communication architecture, which aims to provide automatic brake tests at lower cost than current solutions. The proposed solutions relies exclusively on brake pipe and brake cylinder pressure sensors, a brake release position switch as well as radio communication via standard protocols. The approach is embedded in the Wagon 4.0 concept, which is a holistic approach to a smart freight wagon. The reduction of manual processes yields a strong incentive due to high savings in manual labour and increased productivity.},
  language  = {en}
}
@inproceedings{SchmidtKaschEichleretal.2021,
  author    = {Schmidt, Thomas and Kasch, Susanne and Eichler, Fabian and Thurn, Laura},
  title     = {Process strategies on laser-based melting of glass powder},
  series = {LiM 2021 proceedings},
  booktitle = {LiM 2021 proceedings},
  pages     = {10 Seiten},
  year      = {2021},
  abstract  = {This paper presents the laser-based powder bed fusion (L-PBF) using various glass powders (borosilicate and quartz glass). Compared to metals, these require adapted process strategies. First, the glass powders were characterized with regard to their material properties and their processability in the powder bed. This was followed by investigations of the melting behavior of the glass powders with different laser wavelengths (10.6 µm, 1070 nm). In particular, the experimental setup of a CO2 laser was adapted for the processing of glass powder. An experimental setup with integrated coaxial temperature measurement/control and an inductively heatable build platform was created. This allowed the L-PBF process to be carried out at the transformation temperature of the glasses. Furthermore, the component's material quality was analyzed on three-dimensional test specimen with regard to porosity, roughness, density and geometrical accuracy in order to evaluate the developed L-PBF parameters and to open up possible applications.},
  language  = {en}
}
@inproceedings{AdenackerGerhardsOttenetal.2021,
  author    = {Adenacker, J. and Gerhards, Benjamin and Otten, Christian and Schleser, Markus},
  title     = {Laserstrahlschweißen von Aluminium-Kupfer-Werkstoffkombinationen f{\"u}r die Elektromobilit{\"a}t},
  series = {DVS CONGRESS 2021},
  booktitle = {DVS CONGRESS 2021},
  publisher = {DVS Media GmbH},
  address   = {D{\"u}sseldorf},
  isbn      = {978-3-96144-146-4},
  pages     = {31 -- 38},
  year      = {2021},
  language  = {de}
}
@article{ZabirovSchleserBucherer2021,
  author    = {Zabirov, Alexander and Schleser, Markus and Bucherer, Sebastian},
  title     = {F{\"u}ge- und Dichtkonzept f{\"u}r einen Leichtbauverbrennungsmotor},
  series = {adh{\"a}sion KLEBEN \& DICHTEN},
  volume    = {65},
  journal   = {adh{\"a}sion KLEBEN \& DICHTEN},
  number    = {11},
  publisher = {Springer Nature},
  address   = {Cham},
  issn      = {2192-8681},
  doi       = {10.1007/s35145-021-0531-5},
  pages     = {12 -- 19},
  year      = {2021},
  language  = {de}
}
@article{BraunChengDoweyetal.2021,
  author    = {Braun, Sebastian and Cheng, Chi-Tsun and Dowey, Steve and Wollert, J{\"o}rg},
  title     = {Performance evaluation of skill-based order-assignment in production environments with multi-agent systems},
  series = {IEEE Journal of Emerging and Selected Topics in Industrial Electronics},
  journal   = {IEEE Journal of Emerging and Selected Topics in Industrial Electronics},
  number    = {Early Access},
  publisher = {IEEE},
  address   = {New York},
  issn      = {2687-9735},
  doi       = {10.1109/JESTIE.2021.3108524},
  year      = {2021},
  abstract  = {The fourth industrial revolution introduces disruptive technologies to production environments. One of these technologies are multi-agent systems (MASs), where agents virtualize machines. However, the agent's actual performances in production environments can hardly be estimated as most research has been focusing on isolated projects and specific scenarios. We address this gap by implementing a highly connected and configurable reference model with quantifiable key performance indicators (KPIs) for production scheduling and routing in single-piece workflows. Furthermore, we propose an algorithm to optimize the search of extrema in highly connected distributed systems. The benefits, limits, and drawbacks of MASs and their performances are evaluated extensively by event-based simulations against the introduced model, which acts as a benchmark. Even though the performance of the proposed MAS is, on average, slightly lower than the reference system, the increased flexibility allows it to find new solutions and deliver improved factory-planning outcomes. Our MAS shows an emerging behavior by using flexible production techniques to correct errors and compensate for bottlenecks. This increased flexibility offers substantial improvement potential. The general model in this paper allows the transfer of the results to estimate real systems or other models.},
  language  = {en}
}
@inproceedings{KesslerBalcGebhardtetal.2017,
  author    = {Kessler, Julia and Balc, Nicolae and Gebhardt, Andreas and Abbas, Karim},
  title     = {Basic research on lattice structures focused on the reliance of the cross sectional area and additional coatings},
  series = {The 4th International Conference on Computing and Solutions in Manufacturing Engineering 2016 - CoSME'16},
  booktitle = {The 4th International Conference on Computing and Solutions in Manufacturing Engineering 2016 - CoSME'16},
  edition   = {Vol. 94},
  doi       = {10.1051/matecconf/20179403008},
  pages     = {7 S.},
  year      = {2017},
  language  = {en}
}
@article{Wollert2016,
  author    = {Wollert, J{\"o}rg},
  title     = {OS-Funktionalit{\"a}t ohne OS f{\"u}r das IoT},
  series = {Design \& Elektronik},
  journal   = {Design \& Elektronik},
  number    = {11},
  publisher = {WEKA-Fachmedien},
  address   = {M{\"u}nchen},
  issn      = {0933-8667},
  pages     = {85 -- 90},
  year      = {2016},
  abstract  = {Low-end-Embedded-Plattformen stellen eine hohe Anforderung an die Entscheidungsf{\"a}higkeit des Entwicklers: Zum n{\"a}chstgr{\"o}ßeren Prozessor greifen und ein Betriebssystem benutzen oder doch besser auf das Betriebssystem verzichten? Die Frage l{\"a}sst sich einfach beantworten: Einen Nanokernel verwenden und das Embedded-System mit einem minimalen Footprint realisieren. Adam Dunkels Protothreads sind eine ausgesprochen effiziente Art, Mikrocontroller gut strukturiert zu programmieren und gleichzeitig auf Overhead zu verzichten. So k{\"o}nnen auch mit kleinen 8-bit-Prozessoren anspruchsvolle Aufgaben in einem Thread-Modell bearbeitet werden. Man muss also nicht immer das Rad neu erfinden oder gleich auf Linux-basierte Systeme zur{\"u}ckgreifen.},
  language  = {de}
}
@article{Thomas2016,
  author    = {Thomas, Axel},
  title     = {Genussrechte als Instrument der Unternehmensfinanzierung von kommunalen Wohnungs- baugesellschaften},
  series = {VM Verwaltung und Management},
  volume    = {22},
  journal   = {VM Verwaltung und Management},
  number    = {6},
  publisher = {Nomos},
  address   = {Baden-Baden},
  issn      = {0947-9856},
  doi       = {10.5771/0947-9856-2016-6-322},
  pages     = {322 -- 327},
  year      = {2016},
  abstract  = {Die kommunalen Wohnungsbaugesellschaften und ihr Gesch{\"a}ftszweck bzw. Versorgungsauftrag erfahren aus gesamtgesellschaftlichen Gr{\"u}nden aktuell einen erheblichen Bedeutungszuwachs. Der kommunale Wohnungsbau soll und muss intensiviert werden, da z.B. zunehmend Wohnungsbindungen auslaufen. Bezahlbare Neubauten fehlen speziell Familien, Senioren, Studenten und Fl{\"u}chtlingen. Um das Investitionsvolumen zu bew{\"a}ltigen, bedarf es nicht nur der F{\"o}rderkredite, sondern auch der Zuf{\"u}hrung „frischen Kapitals". Der Beitrag stellt dar, dass Genussrechte ein interessantes und oft unbekanntes Finanzierungsinstrument f{\"u}r kommunale Wohnungsbaugesellschaften mit passgenauen Ausgestaltungsm{\"o}glichkeiten sind. Mit Hilfe von Genussrechten k{\"o}nnen die notwendigen Neubau-Investitionen solide mit Quasi-Eigenkapital unterlegt werden und den sozialen Wohnungsbau wiederbeleben. Genussrechte als Hybridkapital lassen sich mangels gesetzlicher Eingrenzung exakt und individuell ebenso an die Bed{\"u}rfnisse der kommunalen Wohnungsbaugesellschaft anpassen wie an die der Gesellschafter und des jeweiligen Neubauvorhabens.},
  language  = {de}
}
@inproceedings{SchleupenEngemannBagherietal.2017,
  author    = {Schleupen, Josef and Engemann, Heiko and Bagheri, Mohsen and Kallweit, Stephan and Dahmann, Peter},
  title     = {Developing a climbing maintenance robot for tower and rotor blade service of wind turbines},
  series = {Advances in Robot Design and Intelligent Control : Proceedings of the 25th Conference on Robotics in Alpe-Adria-Danube Region (RAAD16)},
  booktitle = {Advances in Robot Design and Intelligent Control : Proceedings of the 25th Conference on Robotics in Alpe-Adria-Danube Region (RAAD16)},
  publisher = {Springer},
  address   = {Cham},
  isbn      = {978-3-319-49058-8},
  doi       = {10.1007/978-3-319-49058-8_34},
  pages     = {310 -- 319},
  year      = {2017},
  language  = {en}
}
@article{EnningPfaff2017,
  author    = {Enning, Manfred and Pfaff, Raphael},
  title     = {G{\"u}terwagen 4.0 - Der G{\"u}terwagen f{\"u}r das Internet der Dinge. Teil 1: Gesamtsystembetrachtung und grundlegendes Konzept},
  series = {ETR - Eisenbahntechnische Rundschau},
  volume    = {66},
  journal   = {ETR - Eisenbahntechnische Rundschau},
  number    = {1/2},
  publisher = {DVV Media Group},
  address   = {Hamburg},
  issn      = {0013-2845},
  pages     = {12 -- 16},
  year      = {2017},
  language  = {de}
}
@article{Enning2017,
  author    = {Enning, Manfred},
  title     = {Vom "K{\"o}nig der Landstraße" zur "Ameise 4.0"},
  series = {ETR - Eisenbahntechnische Rundschau},
  volume    = {66},
  journal   = {ETR - Eisenbahntechnische Rundschau},
  number    = {1/2},
  publisher = {DVV Media Group},
  address   = {Hamburg},
  issn      = {0013-2845},
  pages     = {3},
  year      = {2017},
  abstract  = {Auf Eisenbahn- und Logistikkonferenzen werden gelegentlich Videos von Blattschneiderameisen gezeigt, die effizient und selbstorganisiert große Mengen Material durch den Dschungel transportieren. Daran sollen wir uns ein Beispiel nehmen.},
  language  = {de}
}
@inproceedings{FerreinSchifferKallweit2018,
  author    = {Ferrein, Alexander and Schiffer, Stefan and Kallweit, Stephan},
  title     = {The ROSIN Education Concept - Fostering ROS Industrial-Related Robotics Education in Europe},
  series = {ROBOT 2017: Third Iberian Robotics Conference},
  booktitle = {ROBOT 2017: Third Iberian Robotics Conference},
  publisher = {Springer},
  address   = {Cham},
  isbn      = {978-3-319-70836-2},
  doi       = {10.1007/978-3-319-70836-2_31},
  pages     = {370 -- 381},
  year      = {2018},
  language  = {en}
}
@book{GebhardtKesslerThurn2019,
  author    = {Gebhardt, Andreas and Kessler, Julia and Thurn, Laura},
  title     = {3D printing : understanding additive manufacturing},
  edition   = {2. Auflage},
  publisher = {Hanser},
  address   = {M{\"u}nchen},
  isbn      = {978-1-56990-702-3},
  pages     = {XVI, 204 Seiten},
  year      = {2019},
  language  = {en}
}
@article{BergSchleserDelidovichetal.2018,
  author    = {Berg, Alexander-Karl and Schleser, Markus and Delidovich, Artem and Houben, Alexander},
  title     = {Ultraschallunterst{\"u}tzter Schmelzklebstoffauftrag},
  series = {adh{\"a}sion KLEBEN \& DICHTEN},
  volume    = {Volume 62},
  journal   = {adh{\"a}sion KLEBEN \& DICHTEN},
  number    = {Issue 12},
  publisher = {Springer},
  doi       = {10.1007/s35145-018-0089-z},
  pages     = {32 -- 37},
  year      = {2018},
  language  = {de}
}
@article{KampkerSchleserTriebsetal.2018,
  author    = {Kampker, Achim and Schleser, Markus and Triebs, Johannes and Berg, Alexander-Karl and Hansen, Jan Ole and Fiedler, Falko},
  title     = {Bauteilintegrierte Vorrichtungsfunktionen im Karosseriebau : Aktuelle Ergebnisse im Forschungsprojekt ProeK},
  series = {ZWF Zeitschrift f{\"u}r wirtschaftlichen Fabrikbetrieb},
  volume    = {113},
  journal   = {ZWF Zeitschrift f{\"u}r wirtschaftlichen Fabrikbetrieb},
  number    = {11},
  publisher = {De Gruyter},
  address   = {Berlin},
  issn      = {0947-0085},
  doi       = {10.3139/104.112012},
  pages     = {767 -- 770},
  year      = {2018},
  abstract  = {Das Forschungsprojekt Produktionseffizienz in der Kleinserie (ProeK) erarbeitet kosteng{\"u}nstige und effiziente L{\"o}sungsans{\"a}tze f{\"u}r Prozessketten im Zukunftsfeld der Elektromobilit{\"a}t. Das Teilprojekt Karosserie setzt diese Zielsetzung durch innovative und praxisorientierte Produkt- und Prozesskonzepte mit neuartigen bauteilintegrierten Vorrichtungsfunktionen (BiV) um. Im Teilprojekt Außenhaut sollen Toleranzen adaptiv durch Anpassungen der Prozessparameter sowie Bauteilmanipulation kompensiert werden.},
  language  = {de}
}
@incollection{EngemannDuKallweitetal.2020,
  author    = {Engemann, Heiko and Du, Shengzhi and Kallweit, Stephan and Ning, Chuanfang and Anwar, Saqib},
  title     = {AutoSynPose: Automatic Generation of Synthetic Datasets for 6D Object Pose Estimation},
  series = {Machine Learning and Artificial Intelligence. Proceedings of MLIS 2020},
  booktitle = {Machine Learning and Artificial Intelligence. Proceedings of MLIS 2020},
  publisher = {IOS Press},
  address   = {Amsterdam},
  isbn      = {978-1-64368-137-5},
  doi       = {10.3233/FAIA200770},
  pages     = {89 -- 97},
  year      = {2020},
  abstract  = {We present an automated pipeline for the generation of synthetic datasets for six-dimension (6D) object pose estimation. Therefore, a completely automated generation process based on predefined settings is developed, which enables the user to create large datasets with a minimum of interaction and which is feasible for applications with a high object variance. The pipeline is based on the Unreal 4 (UE4) game engine and provides a high variation for domain randomization, such as object appearance, ambient lighting, camera-object transformation and distractor density. In addition to the object pose and bounding box, the metadata includes all randomization parameters, which enables further studies on randomization parameter tuning. The developed workflow is adaptable to other 3D objects and UE4 environments. An exemplary dataset is provided including five objects of the Yale-CMU-Berkeley (YCB) object set. The datasets consist of 6 million subsegments using 97 rendering locations in 12 different UE4 environments. Each dataset subsegment includes one RGB image, one depth image and one class segmentation image at pixel-level.},
  language  = {en}
}
@article{EngemannDuKallweitetal.2020,
  author    = {Engemann, Heiko and Du, Shengzhi and Kallweit, Stephan and C{\"o}nen, Patrick and Dawar, Harshal},
  title     = {OMNIVIL - an autonomous mobile manipulator for flexible production},
  series = {Sensors},
  volume    = {20},
  journal   = {Sensors},
  number    = {24, art. no. 7249},
  publisher = {MDPI},
  address   = {Basel},
  isbn      = {1424-8220},
  doi       = {10.3390/s20247249},
  pages     = {1 -- 30},
  year      = {2020},
  language  = {en}
}
@inproceedings{UlmerBraunChengetal.2020,
  author    = {Ulmer, Jessica and Braun, Sebastian and Cheng, Chi-Tsun and Dowey, Steve and Wollert, J{\"o}rg},
  title     = {Gamified Virtual Reality Training Environment for the Manufacturing Industry},
  series = {Proceedings of the 2020 19th International Conference on Mechatronics - Mechatronika (ME)},
  booktitle = {Proceedings of the 2020 19th International Conference on Mechatronics - Mechatronika (ME)},
  publisher = {IEEE},
  address   = {New York, NY},
  doi       = {10.1109/ME49197.2020.9286661},
  pages     = {1 -- 6},
  year      = {2020},
  abstract  = {Industry 4.0 imposes many challenges for manufacturing companies and their employees. Innovative and effective training strategies are required to cope with fast-changing production environments and new manufacturing technologies. Virtual Reality (VR) offers new ways of on-the-job, on-demand, and off-premise training. A novel concept and evaluation system combining Gamification and VR practice for flexible assembly tasks is proposed in this paper and compared to existing works. It is based on directed acyclic graphs and a leveling system. The concept enables a learning speed which is adjustable to the users' pace and dynamics, while the evaluation system facilitates adaptive work sequences and allows employee-specific task fulfillment. The concept was implemented and analyzed in the Industry 4.0 model factory at FH Aachen for mechanical assembly jobs.},
  language  = {de}
}
@inproceedings{KoenigWolf2016,
  author    = {K{\"o}nig, Johannes Alexander and Wolf, Martin},
  title     = {A new definition of competence developing games - and a framework to assess them},
  series = {ACHI 2016 : The Ninth International Conference on Advances in Computer-Human Interactions},
  booktitle = {ACHI 2016 : The Ninth International Conference on Advances in Computer-Human Interactions},
  isbn      = {978-1-61208-468-8},
  pages     = {95 -- 97},
  year      = {2016},
  abstract  = {There are different types of games that try to make use of the motivation of a gaming situation in learning contexts. This paper introduces the new terminology 'Competence Developing Game' (CDG) as an umbrella term for all games with this intention. Based on this new terminology, an assessment framework has been developed and validated in scope of an empirical study. Now, all different types of CDGs can be evaluated according to a defined and uniform set of assessment criteria and, thus, are comparable according to their characteristics and effectiveness.},
  language  = {en}
}
@inproceedings{ChavezBermudezWollert2022,
  author    = {Chavez Bermudez, Victor Francisco and Wollert, J{\"o}rg},
  title     = {10BASE-T1L industry 4.0 smart switch for field devices based on IO-Link},
  series = {2022 IEEE 18th International Conference on Factory Communication Systems (WFCS)},
  booktitle = {2022 IEEE 18th International Conference on Factory Communication Systems (WFCS)},
  publisher = {IEEE},
  address   = {New York, NY},
  isbn      = {978-1-6654-1086-1},
  doi       = {10.1109/WFCS53837.2022.9779176},
  pages     = {4 Seiten},
  year      = {2022},
  abstract  = {The recent amendment to the Ethernet physical layer known as the IEEE 802.3cg specification, allows to connect devices up to a distance of one kilometer and delivers a maximum of 60 watts of power over a twisted pair of wires. This new standard, also known as 10BASE-TIL, promises to overcome the limits of current physical layers used for field devices and bring them a step closer to Ethernet-based applications. The main advantage of 10BASE- TIL is that it can deliver power and data over the same line over a long distance, where traditional solutions (e.g., CAN, IO-Link, HART) fall short and cannot match its 10 Mbps bandwidth. Due to its recentness, IOBASE- TIL is still not integrated into field devices and it has been less than two years since silicon manufacturers released the first Ethernet-PHY chips. In this paper, we present a design proposal on how field devices could be integrated into a IOBASE-TIL smart switch that allows plug-and-play connectivity for sensors and actuators and is compliant with the Industry 4.0 vision. Instead of presenting a new field-level protocol for this work, we have decided to adopt the IO-Link specification which already includes a plug-and-play approach with features such as diagnosis and device configuration. The main objective of this work is to explore how field devices could be integrated into 10BASE-TIL Ethernet, its adaption with a well-known protocol, and its integration with Industry 4.0 technologies.},
  language  = {en}
}
@inproceedings{UlmerBraunChengetal.2022,
  author    = {Ulmer, Jessica and Braun, Sebastian and Cheng, Chi-Tsun and Dowey, Steve and Wollert, J{\"o}rg},
  title     = {Usage of digital twins for gamification applications in manufacturing},
  series = {Procedia CIRP Leading manufacturing systems transformation - Proceedings of the 55th CIRP Conference on Manufacturing Systems 2022},
  volume    = {107},
  booktitle = {Procedia CIRP Leading manufacturing systems transformation - Proceedings of the 55th CIRP Conference on Manufacturing Systems 2022},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {2212-8271},
  doi       = {10.1016/j.procir.2022.05.044},
  pages     = {675 -- 680},
  year      = {2022},
  abstract  = {Gamification applications are on the rise in the manufacturing sector to customize working scenarios, offer user-specific feedback, and provide personalized learning offerings. Commonly, different sensors are integrated into work environments to track workers' actions. Game elements are selected according to the work task and users' preferences. However, implementing gamified workplaces remains challenging as different data sources must be established, evaluated, and connected. Developers often require information from several areas of the companies to offer meaningful gamification strategies for their employees. Moreover, work environments and the associated support systems are usually not flexible enough to adapt to personal needs. Digital twins are one primary possibility to create a uniform data approach that can provide semantic information to gamification applications. Frequently, several digital twins have to interact with each other to provide information about the workplace, the manufacturing process, and the knowledge of the employees. This research aims to create an overview of existing digital twin approaches for digital support systems and presents a concept to use digital twins for gamified support and training systems. The concept is based upon the Reference Architecture Industry 4.0 (RAMI 4.0) and includes information about the whole life cycle of the assets. It is applied to an existing gamified training system and evaluated in the Industry 4.0 model factory by an example of a handle mounting.},
  language  = {en}
}
@inproceedings{DannenSchindelePruemmeretal.2022,
  author    = {Dannen, Tammo and Schindele, Benedikt and Pr{\"u}mmer, Marcel and Arntz, Kristian and Bergs, Thomas},
  title     = {Methodology for the self-optimizing determination of additive manufacturing process eligibility and optimization potentials in toolmaking},
  series = {Procedia CIRP Leading manufacturing systems transformation - Proceedings of the 55th CIRP Conference on Manufacturing Systems 2022},
  volume    = {107},
  booktitle = {Procedia CIRP Leading manufacturing systems transformation - Proceedings of the 55th CIRP Conference on Manufacturing Systems 2022},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {2212-8271},
  doi       = {10.1016/j.procir.2022.05.188},
  pages     = {1539 -- 1544},
  year      = {2022},
  abstract  = {Additive Manufacturing (AM) of metallic workpieces faces a continuously rising technological relevance and market size. Producing complex or highly strained unique workpieces is a significant field of application, making AM highly relevant for tool components. Its successful economic application requires systematic workpiece based decisions and optimizations. Considering geometric and technological requirements as well as the necessary post-processing makes deciding effortful and requires in-depth knowledge. As design is usually adjusted to established manufacturing, associated technological and strategic potentials are often neglected. To embed AM in a future proof industrial environment, software-based self-learning tools are necessary. Integrated into production planning, they enable companies to unlock the potentials of AM efficiently. This paper presents an appropriate methodology for the analysis of process-specific AM-eligibility and optimization potential, added up by concrete optimization proposals. For an integrated workpiece characterization, proven methods are enlarged by tooling-specific figures. The first stage of the approach specifies the model's initialization. A learning set of tooling components is described using the developed key figure system. Based on this, a set of applicable rules for workpiece-specific result determination is generated through clustering and expert evaluation. Within the following application stage, strategic orientation is quantified and workpieces of interest are described using the developed key figures. Subsequently, the retrieved information is used for automatically generating specific recommendations relying on the generated ruleset of stage one. Finally, actual experiences regarding the recommendations are gathered within stage three. Statistic learning transfers those to the generated ruleset leading to a continuously deepening knowledge base. This process enables a steady improvement in output quality.},
  language  = {en}
}
@article{PfaffBabilon2023,
  author    = {Pfaff, Raphael and Babilon, Katharina},
  title     = {Railway Challenge - moderne Auflage der Rainhill Trials?},
  series = {Eisenbahntechnische Rundschau : ETR ; Impulsgeber f{\"u}r das System Bahn},
  volume    = {2023},
  journal   = {Eisenbahntechnische Rundschau : ETR ; Impulsgeber f{\"u}r das System Bahn},
  number    = {4},
  publisher = {DVV Media Group},
  address   = {Hamburg},
  issn      = {0013-2845},
  pages     = {55 -- 58},
  year      = {2023},
  abstract  = {Die IMechE Railway Challenge wird j{\"a}hrlich in Stapleford, Großbritannien ausgetragen. Im Rahmen der Challenge entwickeln und bauen Studierende eine Lokomotive und vergleichen sich in verschiedenen Disziplinen, darunter eine automatisierte Zielbremsung, optimale Energier{\"u}ckgewinnung beim Bremsen und minimale Ger{\"a}uschemissionen. Neben diesen und weiteren technischen Wettbewerbsdisziplinen treten die Fahrzeuge und die Teams auch in nicht-technischen Disziplinen wie einer Business Case Challenge an.},
  language  = {de}
}
@article{Pfaff2023,
  author    = {Pfaff, Raphael},
  title     = {Braking distance prediction for vehicle consist in low-speed on-sight operation: a Monte Carlo approach},
  series = {Railway Engineering Science},
  volume    = {31},
  journal   = {Railway Engineering Science},
  number    = {2},
  publisher = {SpringerOpen},
  issn      = {2662-4753 (eISSN)},
  doi       = {10.1007/s40534-023-00303-7},
  pages     = {135 -- 144},
  year      = {2023},
  abstract  = {The first and last mile of a railway journey, in both freight and transit applications, constitutes a high effort and is either non-productive (e.g. in the case of depot operations) or highly inefficient (e.g. in industrial railways). These parts are typically managed on-sight, i.e. with no signalling and train protection systems ensuring the freedom of movement. This is possible due to the rather short braking distances of individual vehicles and shunting consists. The present article analyses the braking behaviour of such shunting units. For this purpose, a dedicated model is developed. It is calibrated on published results of brake tests and validated against a high-definition model for low-speed applications. Based on this model, multiple simulations are executed to obtain a Monte Carlo simulation of the resulting braking distances. Based on the distribution properties and established safety levels, the risk of exceeding certain braking distances is evaluated and maximum braking distances are derived. Together with certain parameters of the system, these can serve in the design and safety assessment of driver assistance systems and automation of these processes.},
  language  = {en}
}
@article{LuftBremenLuft2023,
  author    = {Luft, Angela and Bremen, Sebastian and Luft, Nils},
  title     = {A cost/benefit and flexibility evaluation framework for additive technologies in strategic factory planning},
  series = {Processes},
  volume    = {11},
  journal   = {Processes},
  number    = {7},
  publisher = {MDPI},
  address   = {Basel},
  issn      = {2227-9717},
  doi       = {10.3390/pr11071968},
  pages     = {Artikel 1968},
  year      = {2023},
  abstract  = {There is a growing demand for more flexibility in manufacturing to counter the volatility and unpredictability of the markets and provide more individualization for customers. However, the design and implementation of flexibility within manufacturing systems are costly and only economically viable if applicable to actual demand fluctuations. To this end, companies are considering additive manufacturing (AM) to make production more flexible. This paper develops a conceptual model for the impact quantification of AM on volume and mix flexibility within production systems in the early stages of the factory-planning process. Together with the model, an application guideline is presented to help planners with the flexibility quantification and the factory design process. Following the development of the model and guideline, a case study is presented to indicate the potential impact additive technologies can have on manufacturing flexibility Within the case study, various scenarios with different production system configurations and production programs are analyzed, and the impact of the additive technologies on volume and mix flexibility is calculated. This work will allow factory planners to determine the potential impacts of AM on manufacturing flexibility in an early planning stage and design their production systems accordingly.},
  language  = {en}
}
@inproceedings{ChavezBermudezCruzCastanonRuchayetal.2022,
  author    = {Chavez Bermudez, Victor Francisco and Cruz Castanon, Victor Fernando and Ruchay, Marco and Wollert, J{\"o}rg},
  title     = {Rapid prototyping framework for automation applications based on IO-Link},
  series = {Tagungsband AALE 2022: Wissenstransfer im Spannungsfeld von Autonomisierung und Fachkr{\"a}ftemangel},
  booktitle = {Tagungsband AALE 2022: Wissenstransfer im Spannungsfeld von Autonomisierung und Fachkr{\"a}ftemangel},
  editor    = {Leipzig, Hochschule f{\"u}r Technik, Wirtschaft und Kultur},
  address   = {Leipzig},
  isbn      = {978-3-910103-00-9},
  doi       = {10.33968/2022.28},
  pages     = {8 Seiten},
  year      = {2022},
  abstract  = {The development of protype applications with sensors and actuators in the automation industry requires tools that are independent of manufacturer, and are flexible enough to be modified or extended for any specific requirements. Currently, developing prototypes with industrial sensors and actuators is not straightforward. First of all, the exchange of information depends on the industrial protocol that these devices have. Second, a specific configuration and installation is done based on the hardware that is used, such as automation controllers or industrial gateways. This means that the development for a specific industrial protocol, highly depends on the hardware and the software that vendors provide. In this work we propose a rapid-prototyping framework based on Arduino to solve this problem. For this project we have focused to work with the IO-Link protocol. The framework consists of an Arduino shield that acts as the physical layer, and a software that implements the IO-Link Master protocol. The main advantage of such framework is that an application with industrial devices can be rapid-prototyped with ease as its vendor independent, open-source and can be ported easily to other Arduino compatible boards. In comparison, a typical approach requires proprietary hardware, is not easy to port to another system and is closed-source.},
  language  = {en}
}
@inproceedings{UlmerMostafaWollert2022,
  author    = {Ulmer, Jessica and Mostafa, Youssef and Wollert, J{\"o}rg},
  title     = {Digital Twin Academy: From Zero to Hero through individual learning experiences},
  series = {Tagungsband AALE 2022: Wissenstransfer im Spannungsfeld von Autonomisierung und Fachkr{\"a}ftemangel},
  booktitle = {Tagungsband AALE 2022: Wissenstransfer im Spannungsfeld von Autonomisierung und Fachkr{\"a}ftemangel},
  isbn      = {978-3-910103-00-9},
  doi       = {10.33968/2022.33},
  url       = {http://nbn-resolving.de/urn:nbn:de:bsz:l189-qucosa2-776097},
  pages     = {1 -- 9},
  year      = {2022},
  abstract  = {Digital twins are seen as one of the key technologies of Industry 4.0. Although many research groups focus on digital twins and create meaningful outputs, the technology has not yet reached a broad application in the industry. The main reasons for this imbalance are the complexity of the topic, the lack of specialists, and the unawareness of the twin opportunities. The project "Digital Twin Academy" aims to overcome these barriers by focusing on three actions: Building a digital twin community for discussion and exchange, offering multi-stage training for various knowledge levels, and implementing realworld use cases for deeper insights and guidance. In this work, we focus on creating a flexible learning platform that allows the user to select a training path adjusted to personal knowledge and needs. Therefore, a mix of basic and advanced modules is created and expanded by individual feedback options. The usage of personas supports the selection of the appropriate modules.},
  language  = {en}
}
@inproceedings{UlmerBraunWollert2021,
  author    = {Ulmer, Jessica and Braun, Sebastian and Wollert, J{\"o}rg},
  title     = {Adaptive VR-Produktionsumgebungen f{\"u}r Evaluations- und Schulungst{\"a}tigkeiten},
  series = {Automation 2021: Navigating towards resilient Production},
  booktitle = {Automation 2021: Navigating towards resilient Production},
  publisher = {VDI},
  address   = {D{\"u}sseldorf},
  isbn      = {978-3-18-092392-5},
  issn      = {0083-5560},
  doi       = {10.51202/9783181023921-55},
  pages     = {55 -- 64},
  year      = {2021},
  abstract  = {Industrie 4.0 stellt viele Herausforderungen an produzierende Unternehmen und ihre Besch{\"a}f-tigten. Innovative und effektive Trainingsstrategien sind erforderlich, um mit den sich schnell ver{\"a}ndernden Produktionsumgebungen und neuen Fertigungstechnologien Schritt halten zu k{\"o}nnen. Virtual Reality (VR) bietet neue M{\"o}glichkeiten f{\"u}r On-the-Job, On-Demand- und Off-Premise-Schulungen. Diese Arbeit stellt ein neues VR Schulungssystem vor, welches sich flexible an unterschiedliche Trainingsobjekte auf Grundlage von Rezepten und CAD Modellen anpassen l{\"a}sst. Das Konzept basiert auf gerichteten azyklischen Graphen und einem Level-system. Es erm{\"o}glicht eine benutzerindividuelle Lerngeschwindigkeit mittels visueller Ele-mente. Das Konzept wurde f{\"u}r einen mechanischen Anwendungsfall mit Industriekomponen-ten implementiert und in der Industrie 4.0-Modellfabrik der FH Aachen umgesetzt.},
  language  = {de}
}
@article{ChengWollertChenetal.2023,
  author    = {Cheng, Chi-Tsun and Wollert, J{\"o}rg and Chen, Xi and Fapojuwo, Abraham O.},
  title     = {Guest Editorial : Circuits and Systems for Industry X.0 Applications},
  series = {IEEE Journal on Emerging and Selected Topics in Circuits and Systems},
  volume    = {13},
  journal   = {IEEE Journal on Emerging and Selected Topics in Circuits and Systems},
  edition   = {2},
  publisher = {IEEE},
  address   = {New York},
  issn      = {2156-3357 (Print)},
  doi       = {10.1109/JETCAS.2023.3278843},
  pages     = {457 -- 460},
  year      = {2023},
  language  = {en}
}
@article{AbbasHedwigBalcetal.2023,
  author    = {Abbas, Karim and Hedwig, Lukas and Balc, Nicolae and Bremen, Sebastian},
  title     = {Advanced FFF of PEEK: Infill strategies and material characteristics for rapid tooling},
  series = {Polymers},
  volume    = {2023},
  journal   = {Polymers},
  number    = {15},
  publisher = {MDPI},
  address   = {Basel},
  doi       = {10.3390/polym15214293},
  pages     = {Artikel 4293},
  year      = {2023},
  abstract  = {Traditional vulcanization mold manufacturing is complex, costly, and under pressure due to shorter product lifecycles and diverse variations. Additive manufacturing using Fused Filament Fabrication and high-performance polymers like PEEK offer a promising future in this industry. This study assesses the compressive strength of various infill structures (honeycomb, grid, triangle, cubic, and gyroid) when considering two distinct build directions (Z, XY) to enhance PEEK's economic and resource efficiency in rapid tooling. A comparison with PETG samples shows the behavior of the infill strategies. Additionally, a proof of concept illustrates the application of a PEEK mold in vulcanization. A peak compressive strength of 135.6 MPa was attained in specimens that were 100\% solid and subjected to thermal post-treatment. This corresponds to a 20\% strength improvement in the Z direction. In terms of time and mechanical properties, the anisotropic grid and isotropic cubic infill have emerged for use in rapid tooling. Furthermore, the study highlights that reducing the layer thickness from 0.15 mm to 0.1 mm can result in a 15\% strength increase. The study unveils the successful utilization of a room-temperature FFF-printed PEEK mold in vulcanization injection molding. The parameters and infill strategies identified in this research enable the resource-efficient FFF printing of PEEK without compromising its strength properties. Using PEEK in rapid tooling allows a cost reduction of up to 70\% in tool production.},
  language  = {en}
}
@article{LuftLuftArntz2023,
  author    = {Luft, Angela and Luft, Nils and Arntz, Kristian},
  title     = {A basic description logic for service-oriented architecture in factory planning and operational control in the age of industry 4.0},
  series = {Applied Sciences},
  volume    = {2023},
  journal   = {Applied Sciences},
  number    = {13},
  publisher = {MDPI},
  address   = {Basel},
  doi       = {10.3390/app13137610},
  pages     = {Artikel 7610},
  year      = {2023},
  abstract  = {Manufacturing companies across multiple industries face an increasingly dynamic and unpredictable environment. This development can be seen on both the market and supply side. To respond to these challenges, manufacturing companies must implement smart manufacturing systems and become more flexible and agile. The flexibility in operational planning regarding the scheduling and sequencing of customer orders needs to be increased and new structures must be implemented in manufacturing systems' fundamental design as they constitute much of the operational flexibility available. To this end, smart and more flexible solutions for production planning and control (PPC) are developed. However, scheduling or sequencing is often only considered isolated in a predefined stable environment. Moreover, their orientation on the fundamental logic of the existing IT solutions and their applicability in a dynamic environment is limited. This paper presents a conceptual model for a task-based description logic that can be applied to factory planning, technology planning, and operational control. By using service-oriented architectures, the goal is to generate smart manufacturing systems. The logic is designed to allow for easy and automated maintenance. It is compatible with the existing resource and process allocation logic across operational and strategic factory and production planning.},
  language  = {en}
}
@masterthesis{Ferraioli2023,
  type      = {Bachelor Thesis},
  author    = {Ferraioli, Luigi},
  title     = {Validierung einer Simulationsumgebung f{\"u}r Umfeldsensorik von Schienenfahrzeugen},
  publisher = {FH Aachen},
  address   = {Aachen},
  school      = {Fachhochschule Aachen},
  pages     = {49 Seiten},
  year      = {2023},
  abstract  = {Diese Bachelorarbeit befasst sich mit der digitalen Nachbildung eines Testgel{\"a}ndes sowie eines Schienenfahrzeugs in der Simulationsumgebung Gazebo. Der Schwerpunkt liegt auf der pr{\"a}zisen Abbildung der Umfeldsensorik anhand eines realen Schienenfahrzeuges. Ziel ist die Erzeugung {\"a}quivalenter Messdaten der Simulationsumgebung und des realen Schienenfahrzeuges unter gleichen Einsatzbedingungen. Dazu werden unterschiedliche Verfahren eingesetzt, um die Parameter der einzelnen Sensorik so zu konfigurieren, dass die Messergebnisse mit den Messdaten der realen Sensorik konvergieren. Die Ergebnisse der Messdaten zeigen, dass obwohl die Simulationsumgebung einige physikalische Materialeigenschaften nicht ber{\"u}cksichtigt, eine pr{\"a}zise Abbildung der Sensorik und geometrischen Strukturen des Testgel{\"a}ndes m{\"o}glich ist. Dar{\"u}ber hinaus erm{\"o}glicht die Kombination von Gazebo und ROS2 Integrationstests und die Entwicklung von Softwareanwendungen sowohl in der Simulation als auch auf dem realen Schienenfahrzeug. Eine realit{\"a}tsnahe und reproduzierbare Auswertung der Sensormessdaten der Simulationsumgebung f{\"u}r Schienenfahrzeuge ist somit realisierbar.},
  language  = {de}
}
@incollection{Dreschers2023,
  author    = {Dreschers, Martin},
  title     = {\S25 Arbeitsrechtliche Probleme im Rahmen der Betriebsfortf{\"u}hrung},
  series = {Betriebsfortf{\"u}hrung in Restrukturierung und Insolvenz},
  booktitle = {Betriebsfortf{\"u}hrung in Restrukturierung und Insolvenz},
  editor    = {M{\"o}nning, Rolf-Dieter},
  publisher = {RWS Verlag},
  address   = {K{\"o}ln},
  isbn      = {978-3-8145-2012-4 (print)},
  doi       = {https://doi.org/10.15375/9783814558882-028},
  pages     = {947 -- 988},
  year      = {2023},
  language  = {de}
}
@incollection{Dreschers2023,
  author    = {Dreschers, Martin},
  title     = {\S18 Grenz{\"u}berschreitende Eigenverwaltung},
  series = {HRI II - Handbuch Restrukturierung in der Insolvenz},
  booktitle = {HRI II - Handbuch Restrukturierung in der Insolvenz},
  editor    = {K{\"u}bler, Bruno M. and Bork, Reinhard and Pr{\"u}tting, Hanns},
  publisher = {RWS Verlag},
  address   = {K{\"o}ln},
  isbn      = {978-3-8145-2010-0 (print)},
  doi       = {10.15375/9783814558714-028},
  pages     = {524 -- 556},
  year      = {2023},
  language  = {de}
}
@techreport{BarnatArntzBerneckeretal.2024,
  type      = {Working Paper},
  author    = {Barnat, Miriam and Arntz, Kristian and Bernecker, Andreas and Fissabre, Anke and Franken, Norbert and Goldbach, Daniel and H{\"u}ning, Felix and J{\"o}rissen, J{\"o}rg and Kirsch, Ansgar and Pettrak, J{\"u}rgen and Rexforth, Matthias and Josef, Rosenkranz and Terstegge, Andreas},
  title     = {Strategische Gestaltung von Studieng{\"a}ngen f{\"u}r die Zukunft: Ein kollaborativ entwickeltes Self-Assessment},
  series = {Hochschulforum Digitalisierung - Diskussionspapier},
  journal   = {Hochschulforum Digitalisierung - Diskussionspapier},
  publisher = {Stifterverband f{\"u}r die Deutsche Wissenschaft},
  address   = {Berlin},
  issn      = {2365-7081},
  pages     = {16 Seiten},
  year      = {2024},
  abstract  = {Das Diskussionspapier beschreibt einen Prozess an der FH Aachen zur Entwicklung und Implementierung eines Self-Assessment-Tools f{\"u}r Studieng{\"a}nge. Dieser Prozess zielte darauf ab, die Relevanz der Themen Digitalisierung, Internationalisierung und Nachhaltigkeit in Studieng{\"a}ngen zu st{\"a}rken. Durch Workshops und kollaborative Entwicklung mit Studiendekan:innen entstand ein Fragebogen, der zur Reflexion und strategischen Weiterentwicklung der Studieng{\"a}nge dient.},
  language  = {de}
}
@article{UlmerBraunChengetal.2023,
  author    = {Ulmer, Jessica and Braun, Sebastian and Cheng, Chi-Tsun and Dowey, Steve and Wollert, J{\"o}rg},
  title     = {A human factors-aware assistance system in manufacturing based on gamification and hardware modularisation},
  series = {International Journal of Production Research},
  journal   = {International Journal of Production Research},
  publisher = {Taylor \& Francis},
  issn      = {0020-7543 (Print)},
  doi       = {10.1080/00207543.2023.2166140},
  year      = {2023},
  abstract  = {Assistance systems have been widely adopted in the manufacturing sector to facilitate various processes and tasks in production environments. However, existing systems are mostly equipped with rigid functional logic and do not provide individual user experiences or adapt to their capabilities. This work integrates human factors in assistance systems by adjusting the hardware and instruction presented to the workers' cognitive and physical demands. A modular system architecture is designed accordingly, which allows a flexible component exchange according to the user and the work task. Gamification, the use of game elements in non-gaming contexts, has been further adopted in this work to provide level-based instructions and personalised feedback. The developed framework is validated by applying it to a manual workstation for industrial assembly routines.},
  language  = {en}
}