@misc{KeimerGirbigMayntzetal.2022,
  author    = {Keimer, Jona and Girbig, Leo and Mayntz, Joscha and Tegtmeyer, Philipp and Wendland, Frederik and Dahman, Peter and Fisher, Alex and Dorrington, Graham},
  title     = {Flight mission optimization for eco-efficiency in consideration of electric regeneration and atmospheric conditions},
  series = {AIAA AVIATION 2022 Forum},
  journal   = {AIAA AVIATION 2022 Forum},
  publisher = {AIAA},
  address   = {Reston, Va.},
  doi       = {10.2514/6.2022-4118},
  year      = {2022},
  abstract  = {The development and operation of hybrid or purely electrically powered aircraft in regional air mobility is a significant challenge for the entire aviation sector. This technology is expected to lead to substantial advances in flight performance, energy efficiency, reliability, safety, noise reduction, and exhaust emissions. Nevertheless, any consumed energy results in heat or carbon dioxide emissions and limited electric energy storage capabilities suppress commercial use. Therefore, the significant challenges to achieving eco-efficient aviation are increased aircraft efficiency, the development of new energy storage technologies, and the optimization of flight operations. Two major approaches for higher eco-efficiency are identified: The first one, is to take horizontal and vertical atmospheric motion phenomena into account. Where, in particular, atmospheric waves hold exciting potential. The second one is the use of the regeneration ability of electric aircraft. The fusion of both strategies is expected to improve efficiency. The objective is to reduce energy consumption during flight while not neglecting commercial usability and convenient flight characteristics. Therefore, an optimized control problem based on a general aviation class aircraft has to be developed and validated by flight experiments. The formulated approach enables a development of detailed knowledge of the potential and limitations of optimizing flight missions, considering the capability of regeneration and atmospheric influences to increase efficiency and range.},
  language  = {en}
}
@misc{BraunKrafftTippkoetter2022,
  author    = {Braun, Lena and Krafft, Simone and Tippk{\"o}tter, Nils},
  title     = {Combined supercritical carbon dioxide extraction and chromatography of the algae fatty linoleic and linolenic acid},
  series = {Chemie Ingenieur Technik},
  volume    = {94},
  journal   = {Chemie Ingenieur Technik},
  number    = {9},
  publisher = {Wiley-VCH},
  address   = {Weinheim},
  issn      = {0009-286X},
  doi       = {10.1002/cite.202255308},
  pages     = {1304},
  year      = {2022},
  abstract  = {A method for the integrated extraction and separation of fatty acids from algae using supercritical CO2 is presented. Desmodesmus obliquus and Chlorella sorokiniana were used as algae. First, a method for chromatographic separation of fatty acids of different degrees of saturation was established and optimized. Then, an integrated method for supercritical extraction was developed for both algal species. It was also verified whether prior cell disruption was beneficial for extraction. In developing the method for chromatographic separation, statistical experimental design was used to determine the optimal parameter settings. The methanol content in the mobile phase proved to be the most important parameter for successful separation of the three unsaturated fatty acids oleic acid, linoleic acid, and linolenic acid. Supercritical extraction with dried algae showed that about four times more fatty acids can be extracted from C. sorokiniana relative to the dry mass used.},
  language  = {en}
}
@article{PennerUsherovichNiedermeieretal.2022,
  author    = {Penner, Crystal and Usherovich, Samuel and Niedermeier, Jana and B{\´e}langer-Champagne, Camille and Trinczek, Michael and Paulßen, Elisabeth and Hoehr, Cornelia},
  title     = {Organic Scintillator-Fibre Sensors for Proton Therapy Dosimetry: SCSF-3HF and EJ-260},
  series = {electronics},
  volume    = {12},
  journal   = {electronics},
  number    = {1},
  publisher = {MDPI},
  address   = {Basel},
  issn      = {2079-9292},
  doi       = {10.3390/electronics12010011},
  pages     = {12 Seiten},
  year      = {2022},
  abstract  = {In proton therapy, the dose from secondary neutrons to the patient can contribute to side effects and the creation of secondary cancer. A simple and fast detection system to distinguish between dose from protons and neutrons both in pretreatment verification as well as potentially in vivo monitoring is needed to minimize dose from secondary neutrons. Two 3 mm long, 1 mm diameter organic scintillators were tested for candidacy to be used in a proton-neutron discrimination detector. The SCSF-3HF (1500) scintillating fibre (Kuraray Co. Chiyoda-ku, Tokyo, Japan) and EJ-260 plastic scintillator (Eljen Technology, Sweetwater, TX, USA) were irradiated at the TRIUMF Neutron Facility and the Proton Therapy Research Centre. In the proton beam, we compared the raw Bragg peak and spread-out Bragg peak response to the industry standard Markus chamber detector. Both scintillator sensors exhibited quenching at high LET in the Bragg peak, presenting a peak-to-entrance ratio of 2.59 for the EJ-260 and 2.63 for the SCSF-3HF fibre, compared to 3.70 for the Markus chamber. The SCSF-3HF sensor demonstrated 1.3 times the sensitivity to protons and 3 times the sensitivity to neutrons as compared to the EJ-260 sensor. Combined with our equations relating neutron and proton contributions to dose during proton irradiations, and the application of Birks' quenching correction, these fibres provide valid candidates for inexpensive and replicable proton-neutron discrimination detectors},
  language  = {en}
}
@article{Finkenberger2022,
  author    = {Finkenberger, Isabel Maria},
  title     = {Strukturwandel als transformative Wende},
  series = {disP: The Planning Review},
  volume    = {58},
  journal   = {disP: The Planning Review},
  number    = {3},
  publisher = {Taylor \& Francis},
  address   = {Abingdon},
  issn      = {0251-3625},
  doi       = {10.1080/02513625.2022.2158603},
  pages     = {86 -- 94},
  year      = {2022},
  language  = {de}
}
@article{OjovanSteinmetz2022,
  author    = {Ojovan, Michael I. and Steinmetz, Hans-J{\"u}rgen},
  title     = {Approaches to Disposal of Nuclear Waste},
  series = {Energies},
  volume    = {15},
  journal   = {Energies},
  number    = {20},
  publisher = {MDPI},
  address   = {Basel},
  issn      = {1996-1073},
  doi       = {10.3390/en15207804},
  pages     = {Artikel 7804},
  year      = {2022},
  abstract  = {We present a concise mini overview on the approaches to the disposal of nuclear waste currently used or deployed. The disposal of nuclear waste is the end point of nuclear waste management (NWM) activities and is the emplacement of waste in an appropriate facility without the intention to retrieve it. The IAEA has developed an internationally accepted classification scheme based on the end points of NWM, which is used as guidance. Retention times needed for safe isolation of waste radionuclides are estimated based on the radiotoxicity of nuclear waste. Disposal facilities usually rely on a multi-barrier defence system to isolate the waste from the biosphere, which comprises the natural geological barrier and the engineered barrier system. Disposal facilities could be of a trench type, vaults, tunnels, shafts, boreholes, or mined repositories. A graded approach relates the depth of the disposal facilities' location with the level of hazard. Disposal practices demonstrate the reliability of nuclear waste disposal with minimal expected impacts on the environment and humans.},
  language  = {en}
}
@incollection{MoorkampPetersonUibel2022,
  author    = {Moorkamp, Wilfried and Peterson, Leif Arne and Uibel, Thomas},
  title     = {Nachhaltige Holzbr{\"u}cken f{\"u}r Geh- und Radwege},
  series = {Bauphysik Kalender 2022: Holzbau, 22. Jahrgang},
  booktitle = {Bauphysik Kalender 2022: Holzbau, 22. Jahrgang},
  editor    = {Fouad, Nabil A.},
  publisher = {Ernst \& Sohn},
  address   = {Berlin},
  isbn      = {9783433033609 (Print)},
  doi       = {10.1002/9783433611081.ch17},
  pages     = {574 -- 592},
  year      = {2022},
  abstract  = {Am Lehr- und Forschungsgebiet Holzbau der Fachhochschule Aachen wurden im Rahmen des Forschungsvorhabens „Nachhaltige Standardbr{\"u}cken in Holzbauweise" Standardtypen f{\"u}r Geh- und Radwegbr{\"u}cken entwickelt. Die Br{\"u}cken sind durch konsequente Umsetzungen von Maßnahmen des konstruktiven Holzschutzes f{\"u}r eine Nutzung von mehr als 80~Jahren konzipiert. Innovative L{\"o}sungen f{\"u}r Bauteile und Anschl{\"u}sse sowie Materialalternativen im Bereich des Belages und der Gel{\"a}nder erm{\"o}glichen eine wartungsarme Konstruktion und tragen somit zur Wirtschaftlichkeit und Nachhaltigkeit bei. Um den Einsatz der entwickelten Standardbr{\"u}ckentypen in der Praxis zu erleichtern, wurden Leistungsverzeichnisse, Musterstatiken, Musterzeichnungen und umfangreiche Detailkataloge als Unterst{\"u}tzung f{\"u}r Planer und Bauherren erstellt. Damit die Randbedingungen f{\"u}r eine lange Lebensdauer w{\"a}hrend der Nutzung der Br{\"u}cke erhalten bleiben, wurden Leitf{\"a}den f{\"u}r die Pflege und Wartung sowie f{\"u}r die Br{\"u}ckenpr{\"u}fung erarbeitet. Der Beitrag gibt Einblicke in das Forschungsvorhaben und seine Resultate.},
  language  = {de}
}
@article{SchulteTiggesFoersterNikolovskietal.2022,
  author    = {Schulte-Tigges, Joschua and F{\"o}rster, Marco and Nikolovski, Gjorgji and Reke, Michael and Ferrein, Alexander and Kaszner, Daniel and Matheis, Dominik and Walter, Thomas},
  title     = {Benchmarking of various LiDAR sensors for use in self-driving vehicles in real-world environments},
  series = {Sensors},
  volume    = {22},
  journal   = {Sensors},
  number    = {19},
  publisher = {MDPI},
  address   = {Basel},
  issn      = {1424-8220},
  doi       = {10.3390/s22197146},
  pages     = {20 Seiten},
  year      = {2022},
  abstract  = {Abstract In this paper, we report on our benchmark results of the LiDAR sensors Livox Horizon, Robosense M1, Blickfeld Cube, Blickfeld Cube Range, Velodyne Velarray H800, and Innoviz Pro. The idea was to test the sensors in different typical scenarios that were defined with real-world use cases in mind, in order to find a sensor that meet the requirements of self-driving vehicles. For this, we defined static and dynamic benchmark scenarios. In the static scenarios, both LiDAR and the detection target do not move during the measurement. In dynamic scenarios, the LiDAR sensor was mounted on the vehicle which was driving toward the detection target. We tested all mentioned LiDAR sensors in both scenarios, show the results regarding the detection accuracy of the targets, and discuss their usefulness for deployment in self-driving cars.},
  language  = {en}
}
@article{Finkenberger2022,
  author    = {Finkenberger, Isabel Maria},
  title     = {Transformatives Forschen, Lehren und Handeln im Rheinischen Braunkohlerevier},
  series = {Forum Wohnen und Stadtentwicklung},
  volume    = {2022},
  journal   = {Forum Wohnen und Stadtentwicklung},
  number    = {2},
  publisher = {vhw},
  address   = {Berlin},
  issn      = {1439-7242},
  pages     = {69 -- 72},
  year      = {2022},
  abstract  = {Die Institution Hochschule hat das Potenzial, {\"u}ber transformatives Forschen und Lehren und den entsprechenden Wissenstransfer in den lokalen Kontext strategisch-verl{\"a}ssliche Partnerin der Großen Transformation zur Nachhaltigkeit zu werden und bei der Ausbildung von Pionierinnen und Pionieren des Wandels mitzuwirken. Der Lehr- und Forschungsschwerpunkt „Zukunftsf{\"a}hige Transformation" am Fachbereich Architektur der FH Aachen widmet sich seit 2020 dem Tagebauumfeld Hambach im Rheinischen Revier, um dort angewandt und in Kooperation neue Narrative, innovative Prozesse, ortsbezogene Konzepte und strategische Projekte zu entwickeln und umzusetzen.},
  language  = {de}
}
@incollection{Golland2022,
  author    = {Golland, Alexander},
  title     = {Kommentierung von \S 7 Telekommunikation-Telemedien-Datenschutzgesetz},
  series = {TTDSG},
  booktitle = {TTDSG},
  editor    = {Riechert, Anne and Wilmer, Thomas},
  publisher = {Erich Schmidt},
  address   = {Berlin},
  isbn      = {978-3-503-20978-1},
  pages     = {145 -- 151},
  year      = {2022},
  language  = {de}
}
@incollection{Finkenberger2022,
  author    = {Finkenberger, Isabel Maria},
  title     = {R{\"a}umliche Transformation als Planungsaufgabe},
  series = {Zur{\"u}ck in die Zukunft. Denkmalpflege und Strukturwandel im Rheinischen Revier},
  booktitle = {Zur{\"u}ck in die Zukunft. Denkmalpflege und Strukturwandel im Rheinischen Revier},
  editor    = {Pufke, Andrea},
  publisher = {LVR-Amt f{\"u}r Denkmalpflege im Rheinland},
  address   = {Pulheim},
  pages     = {70 -- 77},
  year      = {2022},
  language  = {de}
}
@book{Laack2022,
  author    = {Laack, Walter van},
  title     = {Schnittstelle Tod: Was lernen wir durch Corona {\"u}ber Leben und Tod?},
  publisher = {van Laack GmbH},
  address   = {Aachen},
  isbn      = {978-3-936624-53-3},
  pages     = {108 Seiten},
  year      = {2022},
  language  = {de}
}
@inproceedings{CrookstonBung2022,
  author    = {Crookston, Brian M. and Bung, Daniel Bernhard},
  title     = {Application of RGB-D cameras in hydraulic laboratory studies},
  series = {Proceedings of the 39th IAHR World Congress},
  booktitle = {Proceedings of the 39th IAHR World Congress},
  editor    = {Ortega-S{\´a}nchez, Miguel},
  publisher = {International Association for Hydro-Environment Engineering and Research (IAHR)},
  address   = {Madrid},
  isbn      = {978-90-832612-1-8},
  issn      = {2521-7119 (print)},
  doi       = {10.3850/IAHR-39WC252171192022964},
  pages     = {5127 -- 5133},
  year      = {2022},
  abstract  = {Non-intrusive measuring techniques have attained a lot of interest in relation to both hydraulic modeling and prototype applications. Complimenting acoustic techniques, significant progress has been made for the development of new optical methods. Computer vision techniques can help to extract new information, e. g. high-resolution velocity and depth data, from videos captured with relatively inexpensive, consumer-grade cameras. Depth cameras are sensors providing information on the distance between the camera and observed features. Currently, sensors with different working principles are available. Stereoscopic systems reference physical image features (passive system) from two perspectives; in order to enhance the number of features and improve the results, a sensor may also estimate the disparity from a detected light to its original projection (active stereo system). In the current study, the RGB-D camera Intel RealSense D435, working on such stereo vision principle, is used in different, typical hydraulic modeling applications. All tests have been conducted at the Utah Water Research Laboratory. This paper will demonstrate the performance and limitations of the RGB-D sensor, installed as a single camera and as camera arrays, applied to 1) detect the free surface for highly turbulent, aerated hydraulic jumps, for free-falling jets and for an energy dissipation basin downstream of a labyrinth weir and 2) to monitor local scours upstream and downstream of a Piano Key Weir. It is intended to share the authors' experiences with respect to camera settings, calibration, lightning conditions and other requirements in order to promote this useful, easily accessible device. Results will be compared to data from classical instrumentation and the literature. It will be shown that even in difficult application, e. g. the detection of a highly turbulent, fluctuating free-surface, the RGB-D sensor may yield similar accuracy as classical, intrusive probes.},
  language  = {en}
}
@article{PourshahidiAchtsnichtOffenhaeusseretal.2022,
  author    = {Pourshahidi, Ali Mohammad and Achtsnicht, Stefan and Offenh{\"a}usser, Andreas and Krause, Hans-Joachim},
  title     = {Frequency Mixing Magnetic Detection Setup Employing Permanent Ring Magnets as a Static Offset Field Source},
  series = {Sensors},
  volume    = {22},
  journal   = {Sensors},
  number    = {22},
  editor    = {Offenh{\"a}usser, Andreas},
  publisher = {MDPI},
  address   = {Basel},
  issn      = {1424-8220},
  doi       = {10.3390/s22228776},
  pages     = {12 Seiten},
  year      = {2022},
  abstract  = {Frequency mixing magnetic detection (FMMD) has been explored for its applications in fields of magnetic biosensing, multiplex detection of magnetic nanoparticles (MNP) and the determination of core size distribution of MNP samples. Such applications rely on the application of a static offset magnetic field, which is generated traditionally with an electromagnet. Such a setup requires a current source, as well as passive or active cooling strategies, which directly sets a limitation based on the portability aspect that is desired for point of care (POC) monitoring applications. In this work, a measurement head is introduced that involves the utilization of two ring-shaped permanent magnets to generate a static offset magnetic field. A steel cylinder in the ring bores homogenizes the field. By variation of the distance between the ring magnets and of the thickness of the steel cylinder, the magnitude of the magnetic field at the sample position can be adjusted. Furthermore, the measurement setup is compared to the electromagnet offset module based on measured signals and temperature behavior.},
  language  = {en}
}
@masterthesis{Kaspor2022,
  type      = {Bachelor Thesis},
  author    = {Kaspor, Alexej},
  title     = {Kritik der digitalen Rationalisierung},
  publisher = {FH Aachen},
  address   = {Aachen},
  pages     = {135 Seiten},
  year      = {2022},
  abstract  = {Digitalisierung macht's m{\"o}glich: mittlerweile beziehen sich Designer:innen in ihrer Konzeptentwicklung immer h{\"a}ufiger auf Referenzdesigns. Sie picken sich die Eigenschaften aus ihnen heraus, von denen sie sich die gr{\"o}ßte Marktf{\"a}higkeit versprechen, und basteln sie zu einem neuen Produkt zusammen. Voil{\`a}. Doch wie unkonventionell kann Design noch sein? Wie viel Luft bleibt der Kreativit{\"a}t unter dem immer enger geschn{\"u}rten Korsett der Marktf{\"a}higkeit? Alexej Kaspor er{\"o}ffnet die Diskussion mit einem provokanten Projekt, das einen kritischen Blick in die Zukunft des Industriedesigns wirft. Dazu fasst er g{\"a}ngige Designprogramme in einer Software zusammen und verbindet sie mit einer k{\"u}nstlichen Intelligenz, die die aktuelle Entwicklung digital rationalisieren und auf die Spitze treiben soll. Diese f{\"u}hrt Meta-Analysen {\"u}ber das Nutzungsverhalten durch und pr{\"u}ft damit Frameworks von Referenzdesigns auf ihre Vermarktbarkeit. Aus diesen entwickelt sie dann Gestaltungsvorschl{\"a}ge, ohne beim Seiltanz zwischen Trendh{\"o}rigkeit und Scheinindividualismus aus dem Gleichgewicht zu kommen. Innerhalb von Sekunden werden den Designer:innen perfekte Vorschl{\"a}ge {\"u}bers Metaverse simuliert. Auf dem Silbertablett serviert, {\"u}bersichtlich und gef{\"a}hrlich einfach. Bereit, kombiniert und in Produktion gebracht zu werden. Auch mit dem Tracking der KI kann niemand mithalten: um immer am Puls der Zeit zu bleiben, benachrichtigt sie die Designer:innen in Echtzeit {\"u}ber die neuesten Innovationen und Trends. Ressourcenraubendes Herumprobieren in CAD-Programmen geh{\"o}rt also der Vergangenheit an. Das Programm schafft Abhilfe, und verspricht dabei auch noch die h{\"o}chste Effizienz, konkret: garantiertes Kapital. Schlagende Argumente, die die Schw{\"a}chen der Konsumgesellschaft und Kommerzialisierung gezielt ausgenutzen. Es entsteht die perfekte Marketingmaßnahme, ein genialer Treiber f{\"u}r den Turbokapitalismus. Kram, den niemand braucht und zynische Statussymbole inklusive. Der Stolz der geltungsbed{\"u}rftigen Designer:innen wird dabei selbstverst{\"a}ndlich nicht untergraben. Sie sollen mitziehen. Mit zahlreichen Notches wird der Erfolg und die Konkurrenzf{\"a}higkeit des Produkts prognostiziert und ihnen Honig ums Maul geschmiert. Die beklemmende Vorahnung wird sich best{\"a}tigen. Schritt f{\"u}r Schritt enteignet die KI den Designer:innen ihre Kreativit{\"a}t, bis sie nicht mehr sind als die Kurator:innen berechenbarer Produktkonzepte. Der Sp{\"a}tkapitalismus hat sie in der Mangel. Versprochen: diese Arbeit l{\"a}sst niemanden kalt.},
  language  = {de}
}
@masterthesis{Lebrecht2022,
  type      = {Bachelor Thesis},
  author    = {Lebrecht, Rike-Charlotte},
  title     = {Inga : ein modulares hydroponisches System f{\"u}r Endverbraucher},
  publisher = {FH Aachen},
  address   = {Aachen},
  year      = {2022},
  abstract  = {In dieser Arbeit wurde sich mit der Frage auseinandergesetzt, wie sich der Nahrungsmittelanbau im urbanen Raum entwickeln k{\"o}nnte. Eine spannende Alternative zu traditionellen Anbaumethoden ist die Hydroponik, der Anbau von Pflanzen ohne Erde. Basierend auf dieser Technologie wurde in diesem Projekt ein Indoor-Garden-System gestaltet, welches den Nahrungsmittelanbau zur{\"u}ck zur Verbraucher:In bringt und zu einem bewussteren Umgang mit Lebensmitteln anregen soll. Denn mit „INGA" kann frisches, pestizidfreies Blattgem{\"u}se ganz einfach zu Hause selbst angebaut werden. Das hydroponische System schafft mithilfe einer N{\"a}hrstoffl{\"o}sung und k{\"u}nstlichem Licht optimale Wachstumsbedingungen f{\"u}r die Pflanzen - ganz unabh{\"a}ngig von {\"o}rtlichen Gegebenheiten. Mithilfe seiner Modularit{\"a}t k{\"o}nnen Nutzer:Innen „INGA" nach Belieben konfigurieren. Damit wird es einer breiten Zielgruppe mit unterschiedlichen Bed{\"u}rfnissen gerecht und erm{\"o}glicht pestizidfreie Nahrung - auch in den St{\"a}dten.},
  language  = {de}
}
@masterthesis{Janssen2022,
  type      = {Bachelor Thesis},
  author    = {Janssen, Hanna},
  title     = {UMGARNT : Handarbeit als Mittel zur Festigung der emotionalen Bindung zu M{\"o}belst{\"u}cken},
  publisher = {FH Aachen},
  address   = {Aachen},
  pages     = {132 Seiten},
  year      = {2022},
  abstract  = {Nach drei Jahren ist der Anblick der beigen Kommode doch etwas langweilig geworden und es steht ein Tapetenwechsel an? Das ist noch lange kein Grund, neue M{\"o}bel kaufen zu m{\"u}ssen. Mit dem „BOBBI"-Regal l{\"a}sst sich das Farbkonzept des M{\"o}belst{\"u}cks fortlaufend anpassen. Das reduzierte Grundgestell basiert auf einem einfachen Stecksystem und erm{\"o}glicht nicht nur einen schnellen, intuitiven Aufbau, sondern auch eine modulare Erweiterung des Regalsystems. Eint{\"o}nig? Nein Danke! Zeitloses, langlebiges Design muss nicht schlicht und farblos sein! Der Schl{\"u}ssel liegt in der Individualisierbarkeit. Mithilfe einer einfachen textilen Bespannungstechnik passt der Kunde das Ger{\"u}st nach seinen Vorstellungen an. Auf diese Weise kann der Charakter des M{\"o}belst{\"u}cks nicht nur farblich, sondern auch strukturell regelm{\"a}ßig ver{\"a}ndert werden und tr{\"a}gt zu einer nachhaltigen und achtsamen Raumgestaltung bei.},
  language  = {de}
}
@masterthesis{Laubkermeier2022,
  type      = {Bachelor Thesis},
  author    = {Laubkermeier, Kim},
  title     = {trust me},
  publisher = {FH Aachen},
  address   = {Aachen},
  pages     = {94 Seiten},
  year      = {2022},
  abstract  = {"trust me" ist eine schwarz-weiß Fotoserie, pr{\"a}sentiert als Diashow mit unterlegtem Soundtrack. Es geht um das Vertrauen zwischen Model, Fotografin und Betrachter:innen. Die Darsteller sind ausschließlich homosexuelle M{\"a}nner und begeben sich in intime Situationen und Posen. Die Fotos sind {\"u}berwiegend Aktaufnahmen und nehmen eine pornografische Richtung an. Die Fragestellung zu Beginn war, wie weit vertrauen die unerfahrenen Models der Fotografin und was sind diese bereit, von sich zu zeigen. Die offene Kommunikation {\"u}ber die Richtung des Projekts war die essenzielle Basis f{\"u}r die Fotoshootings. W{\"a}hrend des Fotografierens lag der Fokus auf m{\"o}glichst verschiedenen Blickwinkeln, Kulissen, Ausleuchtungen und Motiven. Zus{\"a}tzlich war der sensible Umgang mit den M{\"a}nnern eine Vertrauensprobe."trust me" l{\"a}sst auf diversen Ebenen tief blicken und zeigt, wie loslassen aussieht.},
  language  = {de}
}
@masterthesis{IncemanCremer2022,
  type      = {Bachelor Thesis},
  author    = {Inceman Cremer, Suzan},
  title     = {Kouyou : Ort im Raum},
  publisher = {FH Aachen},
  address   = {Aachen},
  pages     = {85 Seiten},
  year      = {2022},
  abstract  = {Selbstliebe, der Moment der Ruhe, sich eine mentale Pause erlauben und von allem bewusst abzuschalten, sind aktuelle Themen unserer Gesellschaft. Die Zeit, in der wir leben, bewegt sich in einer Geschwindigkeit, die alle unsere Sinne {\"u}berlastet und uns nicht mehr erlaubt, selbst zuzuh{\"o}ren oder volle Momente der Ruhe zu erleben. Thema der Bachelorarbeit ist der Entwurf eines Sitzm{\"o}bels, welches inspiriert ist durch die sakralische Architektur. Der Stuhl soll das Gef{\"u}hl von Umformung und Leichtigkeit vermitteln. Er ist aus Eiche gebaut und unterst{\"u}tzt den Menschen in seiner bewussten Sitzhaltung. Die Eiche ist ein Baum, der f{\"u}r Kraft, Durchhalteverm{\"o}gen und Gerechtigkeit steht. Es heißt auch, wenn man eine Eiche sieht, sie umarmen soll, da sie heilende Kr{\"a}fte hat. Hier ist aber die Eiche, die den Menschen symbolisch umarmen soll, wenn man auf ihr sitzt. Und somit spielen Architektur, M{\"o}bel und der Mensch eine spielende Rolle, und zwar ist es die menschliche Haltung im Raum.},
  language  = {de}
}
@inproceedings{SattlerAttiAlexopoulosetal.2022,
  author    = {Sattler, Johannes Christoph and Atti, Vikrama Naga Babu and Alexopoulos, Spiros and Teixeira Boura, Cristiano Jos{\´e} and Herrmann, Ulf and Dutta, Siddharth and Kioutsioukis, Ioannis},
  title     = {DNI forecast tool for the smart operation of a parabolic trough collector system with concrete thermal energy storage: Theory, results and outlook},
  series = {SolarPACES 2022 conference proceedings},
  booktitle = {SolarPACES 2022 conference proceedings},
  number    = {1},
  publisher = {TIB Open Publishing},
  address   = {Hannover},
  issn      = {2751-9899 (online)},
  doi       = {10.52825/solarpaces.v1i.731},
  pages     = {9 Seiten},
  year      = {2022},
  abstract  = {This work presents a basic forecast tool for predicting direct normal irradiance (DNI) in hourly resolution, which the Solar-Institut J{\"u}lich (SIJ) is developing within a research project. The DNI forecast data shall be used for a parabolic trough collector (PTC) system with a concrete thermal energy storage (C-TES) located at the company KEAN Soft Drinks Ltd in Limassol, Cyprus. On a daily basis, 24-hour DNI prediction data in hourly resolution shall be automatically produced using free or very low-cost weather forecast data as input. The purpose of the DNI forecast tool is to automatically transfer the DNI forecast data on a daily basis to a main control unit (MCU). The MCU automatically makes a smart decision on the operation mode of the PTC system such as steam production mode and/or C-TES charging mode. The DNI forecast tool was evaluated using historical data of measured DNI from an on-site weather station, which was compared to the DNI forecast data. The DNI forecast tool was tested using data from 56 days between January and March 2022, which included days with a strong variation in DNI due to cloud passages. For the evaluation of the DNI forecast reliability, three categories were created and the forecast data was sorted accordingly. The result was that the DNI forecast tool has a reliability of 71.4 \% based on the tested days. The result fulfils SIJ's aim to achieve a reliability of around 70 \%, but SIJ aims to still improve the DNI forecast quality.},
  language  = {en}
}
@incollection{HoffschmidtAlexopoulosGoettscheetal.2022,
  author    = {Hoffschmidt, Bernhard and Alexopoulos, Spiros and G{\"o}ttsche, Joachim and Sauerborn, Markus and Kaufhold, O.},
  title     = {High Concentration Solar Collectors},
  series = {Comprehensive Renewable Energy (Second Edition) / Volume 3: Solar Thermal Systems: Components and Applications},
  booktitle = {Comprehensive Renewable Energy (Second Edition) / Volume 3: Solar Thermal Systems: Components and Applications},
  publisher = {Elsevier},
  address   = {Amsterdam},
  isbn      = {978-0-12-819734-9},
  doi       = {10.1016/B978-0-12-819727-1.00058-3},
  pages     = {198 -- 245},
  year      = {2022},
  abstract  = {Solar thermal concentrated power is an emerging technology that provides clean electricity for the growing energy market. To the solar thermal concentrated power plant systems belong the parabolic trough, the Fresnel collector, the solar dish, and the central receiver system. For high-concentration solar collector systems, optical and thermal analysis is essential. There exist a number of measurement techniques and systems for the optical and thermal characterization of the efficiency of solar thermal concentrated systems. For each system, structure, components, and specific characteristics types are described. The chapter presents additionally an outline for the calculation of system performance and operation and maintenance topics. One main focus is set to the models of components and their construction details as well as different types on the market. In the later part of this article, different criteria for the choice of technology are analyzed in detail.},
  language  = {en}
}