@article{MolinnusIkenJohnenetal.2022,
  author    = {Molinnus, Denise and Iken, Heiko and Johnen, Anna Lynn and Richstein, Benjamin and Hellmich, Lena and Poghossian, Arshak and Knoch, Joachim and Sch{\"o}ning, Michael Josef},
  title     = {Miniaturized pH-Sensitive Field-Effect Capacitors with Ultrathin Ta₂O₅ Films Prepared by Atomic Layer Deposition},
  series = {physica status solidi (a) applications and materials science},
  volume    = {219},
  journal   = {physica status solidi (a) applications and materials science},
  number    = {8},
  publisher = {Wiley-VCH},
  address   = {Weinheim},
  issn      = {1862-6319},
  doi       = {10.1002/pssa.202100660},
  pages     = {7 Seiten},
  year      = {2022},
  abstract  = {Miniaturized electrolyte-insulator-semiconductor capacitors (EISCAPs) with ultrathin gate insulators have been studied in terms of their pH-sensitive sensor characteristics: three different EISCAP systems consisting of Al-p-Si-Ta2O5(5 nm), Al-p-Si-Si3N4(1 or 2 nm)-Ta2O5 (5 nm), and Al-p-Si-SiO2(3.6 nm)-Ta2O5(5 nm) layer structures are characterized in buffer solution with different pH values by means of capacitance-voltage and constant capacitance method. The SiO2 and Si3N4 gate insulators are deposited by rapid thermal oxidation and rapid thermal nitridation, respectively, whereas the Ta2O5 film is prepared by atomic layer deposition. All EISCAP systems have a clear pH response, favoring the stacked gate insulators SiO2-Ta2O5 when considering the overall sensor characteristics, while the Si3N4(1 nm)-Ta2O5 stack delivers the largest accumulation capacitance (due to the lower equivalent oxide thickness) and a higher steepness in the slope of the capacitance-voltage curve among the studied stacked gate insulator systems.},
  language  = {en}
}
@article{HeuermannEmmrichBongartz2022,
  author    = {Heuermann, Holger and Emmrich, Thomas and Bongartz, Simon},
  title     = {Microwave spark plug to support ignitions with high compression ratios},
  series = {IEEE Transactions on Plasma Science},
  journal   = {IEEE Transactions on Plasma Science},
  number    = {Early Access},
  publisher = {IEEE},
  issn      = {1939-9375},
  doi       = {10.1109/TPS.2022.3183690},
  pages     = {1 -- 6},
  year      = {2022},
  abstract  = {Upcoming gasoline engines should run with a larger number of fuels beginning from petrol over methanol up to gas by a wide range of compression ratios and a homogeneous charge. In this article, the microwave (MW) spark plug, based on a high-speed frequency hopping system, is introduced as a solution, which can support a nitrogen compression ratio up to 1:39 in a chamber and more. First, an overview of the high-speed frequency hopping MW ignition and operation system as well as the large number of applications are presented. Both gives an understanding of this new base technology for MW plasma generation. Focus of the theoretical part is the explanation of the internal construction of the spark plug, on the achievable of the high voltage generation as well as the high efficiency to hold the plasma. In detail, the development process starting with circuit simulations and ending with the numerical multiphysics field simulations is described. The concept is evaluated with a reference prototype covering the frequency range between 2.40 and 2.48 GHz and working over a large power range from 20 to 200 W. A larger number of different measurements starting by vector hot-S11 measurements and ending by combined working scenarios out of hot temperature, high pressure and charge motion are winding up the article. The limits for the successful pressure tests were given by the pressure chamber. Pressures ranged from 1 to 39 bar and charge motion up to 25 m/s as well as temperatures from 30◦ to 125◦.},
  language  = {en}
}
@article{MonakhovaDiehl2022,
  author    = {Monakhova, Yulia and Diehl, Bernd W.K.},
  title     = {Multinuclear NMR screening of pharmaceuticals using standardization by 2H integral of a deuterated solvent},
  series = {Journal of Pharmaceutical and Biomedical Analysis},
  volume    = {209},
  journal   = {Journal of Pharmaceutical and Biomedical Analysis},
  number    = {Article number: 114530},
  publisher = {Elsevier},
  isbn      = {0731-7085},
  doi       = {10.1016/j.jpba.2021.114530},
  year      = {2022},
  abstract  = {NMR standardization approach that uses the 2H integral of deuterated solvent for quantitative multinuclear analysis of pharmaceuticals is described. As a proof of principle, the existing NMR procedure for the analysis of heparin products according to US Pharmacopeia monograph is extended to the determination of Na+ and Cl- content in this matrix. Quantification is performed based on the ratio of a 23Na (35Cl) NMR integral and 2H NMR signal of deuterated solvent, D2O, acquired using the specific spectrometer hardware. As an alternative, the possibility of 133Cs standardization using the addition of Cs2CO3 stock solution is shown. Validation characteristics (linearity, repeatability, sensitivity) are evaluated. A holistic NMR profiling of heparin products can now also be used for the quantitative determination of inorganic compounds in a single analytical run using a single sample. In general, the new standardization methodology provides an appealing alternative for the NMR screening of inorganic and organic components in pharmaceutical products.},
  language  = {en}
}
@article{MolinnusJanusFangetal.2022,
  author    = {Molinnus, Denise and Janus, Kevin Alexander and Fang, Anyelina C. and Drinic, Aleksander and Achtsnicht, Stefan and K{\"o}pf, Marius and Keusgen, Michael and Sch{\"o}ning, Michael Josef},
  title     = {Thick-film carbon electrode deposited onto a biodegradable fibroin substrate for biosensing applications},
  series = {Physica status solidi (a)},
  volume    = {219},
  journal   = {Physica status solidi (a)},
  number    = {23},
  publisher = {Wiley-VCH},
  address   = {Weinheim},
  issn      = {1862-6319},
  doi       = {10.1002/pssa.202200100},
  pages     = {1 -- 9},
  year      = {2022},
  abstract  = {This study addresses a proof-of-concept experiment with a biocompatible screen-printed carbon electrode deposited onto a biocompatible and biodegradable substrate, which is made of fibroin, a protein derived from silk of the Bombyx mori silkworm. To demonstrate the sensor performance, the carbon electrode is functionalized as a glucose biosensor with the enzyme glucose oxidase and encapsulated with a silicone rubber to ensure biocompatibility of the contact wires. The carbon electrode is fabricated by means of thick-film technology including a curing step to solidify the carbon paste. The influence of the curing temperature and curing time on the electrode morphology is analyzed via scanning electron microscopy. The electrochemical characterization of the glucose biosensor is performed by amperometric/voltammetric measurements of different glucose concentrations in phosphate buffer. Herein, systematic studies at applied potentials from 500 to 1200 mV to the carbon working electrode (vs the Ag/AgCl reference electrode) allow to determine the optimal working potential. Additionally, the influence of the curing parameters on the glucose sensitivity is examined over a time period of up to 361 days. The sensor shows a negligible cross-sensitivity toward ascorbic acid, noradrenaline, and adrenaline. The developed biocompatible biosensor is highly promising for future in vivo and epidermal applications.},
  language  = {en}
}
@article{EngelmannPourshahidiShalabyetal.2022,
  author    = {Engelmann, Ulrich M. and Pourshahidi, Mohammad Ali and Shalaby, Ahmed and Krause, Hans-Joachim},
  title     = {Probing particle size dependency of frequency mixing magnetic detection with dynamic relaxation simulation},
  series = {Journal of Magnetism and Magnetic Materials},
  volume    = {563},
  journal   = {Journal of Magnetism and Magnetic Materials},
  number    = {In progress, Art. No. 169965},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {0304-8853},
  doi       = {10.1016/j.jmmm.2022.169965},
  year      = {2022},
  abstract  = {Biomedical applications of magnetic nanoparticles (MNP) fundamentally rely on the particles' magnetic relaxation as a response to an alternating magnetic field. The magnetic relaxation complexly depends on the interplay of MNP magnetic and physical properties with the applied field parameters. It is commonly accepted that particle core size is a major contributor to signal generation in all the above applications, however, most MNP samples comprise broad distribution spanning nm and more. Therefore, precise knowledge of the exact contribution of individual core sizes to signal generation is desired for optimal MNP design generally for each application. Specifically, we present a magnetic relaxation simulation-driven analysis of experimental frequency mixing magnetic detection (FMMD) for biosensing to quantify the contributions of individual core size fractions towards signal generation. Applying our method to two different experimental MNP systems, we found the most dominant contributions from approx. 20 nm sized particles in the two independent MNP systems. Additional comparison between freely suspended and immobilized MNP also reveals insight in the MNP microstructure, allowing to use FMMD for MNP characterization, as well as to further fine-tune its applicability in biosensing.},
  language  = {en}
}
@article{HarrisKleefeld2022,
  author    = {Harris, Isaac and Kleefeld, Andreas},
  title     = {Analysis and computation of the transmission eigenvalues with a conductive boundary condition},
  series = {Applicable Analysis},
  volume    = {101},
  journal   = {Applicable Analysis},
  number    = {6},
  publisher = {Taylor \& Francis},
  address   = {London},
  issn      = {1563-504X},
  doi       = {10.1080/00036811.2020.1789598},
  pages     = {1880 -- 1895},
  year      = {2022},
  abstract  = {We provide a new analytical and computational study of the transmission eigenvalues with a conductive boundary condition. These eigenvalues are derived from the scalar inverse scattering problem for an inhomogeneous material with a conductive boundary condition. The goal is to study how these eigenvalues depend on the material parameters in order to estimate the refractive index. The analytical questions we study are: deriving Faber-Krahn type lower bounds, the discreteness and limiting behavior of the transmission eigenvalues as the conductivity tends to infinity for a sign changing contrast. We also provide a numerical study of a new boundary integral equation for computing the eigenvalues. Lastly, using the limiting behavior we will numerically estimate the refractive index from the eigenvalues provided the conductivity is sufficiently large but unknown.},
  language  = {en}
}
@article{FunkeEschRoosen2022,
  author    = {Funke, Harald and Esch, Thomas and Roosen, Petra},
  title     = {Antriebssystemanpassungen zur Verwendung von LPG als Flugkraftstoff},
  series = {Motortechnische Zeitschrift (MTZ)},
  volume    = {2022},
  journal   = {Motortechnische Zeitschrift (MTZ)},
  number    = {83},
  publisher = {Springer Nature},
  address   = {Basel},
  doi       = {10.1007/s35146-021-0778-2},
  pages     = {58 -- 62},
  year      = {2022},
  abstract  = {Auch in der allgemeinen Luftfahrt w{\"a}re es w{\"u}nschenswert, die bereits vorhandenen Verbrennungsmotoren mit weniger CO₂-tr{\"a}chtigen Kraftstoffen als dem heute weit verbreiteten Avgas 100LL betreiben zu k{\"o}nnen. Es ist anzunehmen, dass im Vergleich die unter Normalbedingungen gasf{\"o}rmigen Kraftstoffe CNG, LPG oder LNG deutlich weniger Emissionen produzieren. Erforderliche Antriebssystemanpassungen wurden im Rahmen eines Forschungsprojekts an der FH Aachen untersucht.},
  language  = {de}
}
@article{WeldenPoghossianVahidpouretal.2022,
  author    = {Welden, Melanie and Poghossian, Arshak and Vahidpour, Farnoosh and Wendlandt, Tim and Keusgen, Michael and Wege, Christina and Sch{\"o}ning, Michael Josef},
  title     = {Towards multi-analyte detection with field-effect capacitors modified with tobacco mosaic virus bioparticles as enzyme nanocarriers},
  series = {Biosensors},
  volume    = {12},
  journal   = {Biosensors},
  number    = {1},
  publisher = {MDPI},
  address   = {Basel},
  issn      = {2079-6374},
  doi       = {10.3390/bios12010043},
  pages     = {Artikel 43},
  year      = {2022},
  abstract  = {Utilizing an appropriate enzyme immobilization strategy is crucial for designing enzyme-based biosensors. Plant virus-like particles represent ideal nanoscaffolds for an extremely dense and precise immobilization of enzymes, due to their regular shape, high surface-to-volume ratio and high density of surface binding sites. In the present work, tobacco mosaic virus (TMV) particles were applied for the co-immobilization of penicillinase and urease onto the gate surface of a field-effect electrolyte-insulator-semiconductor capacitor (EISCAP) with a p-Si-SiO₂-Ta₂O₅ layer structure for the sequential detection of penicillin and urea. The TMV-assisted bi-enzyme EISCAP biosensor exhibited a high urea and penicillin sensitivity of 54 and 85 mV/dec, respectively, in the concentration range of 0.1-3 mM. For comparison, the characteristics of single-enzyme EISCAP biosensors modified with TMV particles immobilized with either penicillinase or urease were also investigated. The surface morphology of the TMV-modified Ta₂O₅-gate was analyzed by scanning electron microscopy. Additionally, the bi-enzyme EISCAP was applied to mimic an XOR (Exclusive OR) enzyme logic gate.},
  language  = {en}
}
@article{Finkenberger2022,
  author    = {Finkenberger, Isabel Maria},
  title     = {Strukturwandel als transformative Wende},
  series = {disP: The Planning Review},
  volume    = {58},
  journal   = {disP: The Planning Review},
  number    = {3},
  publisher = {Taylor \& Francis},
  address   = {Abingdon},
  issn      = {0251-3625},
  doi       = {10.1080/02513625.2022.2158603},
  pages     = {86 -- 94},
  year      = {2022},
  language  = {de}
}
@article{KleefeldZimmermann2022,
  author    = {Kleefeld, Andreas and Zimmermann, M.},
  title     = {Computing Elastic Interior Transmission Eigenvalues},
  series = {Integral Methods in Science and Engineering},
  journal   = {Integral Methods in Science and Engineering},
  editor    = {Constanda, Christian and Bodmann, Bardo E.J. and Harris, Paul J.},
  publisher = {Birkh{\"a}user},
  address   = {Cham},
  isbn      = {978-3-031-07171-3},
  doi       = {10.1007/978-3-031-07171-3_10},
  pages     = {139 -- 155},
  year      = {2022},
  abstract  = {An alternative method is presented to numerically compute interior elastic transmission eigenvalues for various domains in two dimensions. This is achieved by discretizing the resulting system of boundary integral equations in combination with a nonlinear eigenvalue solver. Numerical results are given to show that this new approach can provide better results than the finite element method when dealing with general domains.},
  language  = {en}
}