@article{JensKaldenhoffKirschnerHermannsetal.2014, author = {Jens, Otto and Kaldenhoff, E. and Kirschner-Hermanns, R. and M{\"u}hl, Thomas and Klinge, Uwe}, title = {Elongation of textile pelvic floor implants under load is related to complete loss of effective porosity, thereby favoring incorporation in scar plates}, series = {Journal of biomedical materials research. Part A}, volume = {102}, journal = {Journal of biomedical materials research. Part A}, number = {4}, publisher = {Wiley}, address = {New York}, issn = {1552-4965}, doi = {10.1002/jbm.a.34767}, pages = {1079 -- 1084}, year = {2014}, abstract = {Use of textile structures for reinforcement of pelvic floor structures has to consider mechanical forces to the implant, which are quite different to the tension free conditions of the abdominal wall. Thus, biomechanical analysis of textile devices has to include the impact of strain on stretchability and effective porosity. Prolift® and Prolift + M®, developed for tension free conditions, were tested by measuring stretchability and effective porosity applying mechanical strain. For comparison, we used Dynamesh-PR4®, which was designed for pelvic floor repair to withstand mechanical strain. Prolift® at rest showed moderate porosity with little stretchability but complete loss of effective porosity at strain of 4.9 N/cm. Prolift + M® revealed an increased porosity at rest, but at strain showed high stretchability, with subsequent loss of effective porosity at strain of 2.5 N/cm. Dynamesh PR4® preserved its high porosity even under strain, but as consequence of limited stretchability. Though in tension free conditions Prolift® and Prolift + M® can be considered as large pore class I meshes, application of mechanical strain rapidly lead to collapse of pores. The loss of porosity at mechanical stress can be prevented by constructions with high structural stability. Assessment of porosity under strain was found helpful to define requirements for pelvic floor devices. Clinical studies have to prove whether devices with high porosity as well as high structural stability can improve the patients' outcome.}, language = {en} } @incollection{TranStaat2014, author = {Tran, Thanh Ngoc and Staat, Manfred}, title = {Shakedown analysis of Reissner-Mindlin plates using the edge-based smoothed finite element method}, series = {Direct methods for limit states in structures and materials / Dieter Weichert ; Alan Ponter, ed.}, booktitle = {Direct methods for limit states in structures and materials / Dieter Weichert ; Alan Ponter, ed.}, publisher = {Springer}, address = {Dordrecht [u.a.]}, isbn = {978-94-007-6826-0 (Print) 978-94-007-6827-7 (Online)}, doi = {10.1007/978-94-007-6827-7_5}, pages = {101 -- 117}, year = {2014}, abstract = {This paper concerns the development of a primal-dual algorithm for limit and shakedown analysis of Reissner-Mindlin plates made of von Mises material. At each optimization iteration, the lower bound of the shakedown load multiplier is calculated simultaneously with the upper bound using the duality theory. An edge-based smoothed finite element method (ES-FEM) combined with the discrete shear gap (DSG) technique is used to improve the accuracy of the solutions and to avoid the transverse shear locking behaviour. The method not only possesses all inherent features of convergence and accuracy from ES-FEM, but also ensures that the total number of variables in the optimization problem is kept to a minimum compared with the standard finite element formulation. Numerical examples are presented to demonstrate the effectiveness of the present method.}, language = {en} } @article{WincklerKruegerSchnitzleretal.2014, author = {Winckler, Silvia and Krueger, Rolf and Schnitzler, Thomas and Zang, Werner and Fischer, Rainer and Biselli, Manfred}, title = {A sensitive monitoring system for mammalian cell cultivation processes: a PAT approach}, series = {Bioprocess and biosystems engineering}, volume = {37}, journal = {Bioprocess and biosystems engineering}, number = {5}, publisher = {Springer}, address = {Berlin, Heidelberg}, issn = {1615-7591 (Print) 1615-7605 (Online)}, doi = {10.1007/s00449-013-1062-8}, pages = {901 -- 912}, year = {2014}, abstract = {Biopharmaceuticals such as antibodies are produced in cultivated mammalian cells, which must be monitored to comply with good manufacturing practice. We, therefore, developed a fully automated system comprising a specific exhaust gas analyzer, inline analytics and a corresponding algorithm to precisely determine the oxygen uptake rate, carbon dioxide evolution rate, carbon dioxide transfer rate, transfer quotient and respiratory quotient without interrupting the ongoing cultivation, in order to assess its reproducibility. The system was verified using chemical simulation experiments and was able to measure the respiratory activity of hybridoma cells and DG44 cells (derived from Chinese hamster ovary cells) with satisfactory results at a minimum viable cell density of ~2.0 × 10⁵ cells ml⁻¹. The system was suitable for both batch and fed-batch cultivations in bubble-aerated and membrane-aerated reactors, with and without the control of pH and dissolved oxygen.}, language = {en} } @article{BandodkarMolinnusMirzaetal.2014, author = {Bandodkar, Amay J. and Molinnus, Denise and Mirza, Omar and Guinovart, Tomas and Windmiller, Joshua R. and Valdes-Ramirez, Gabriela and Andrade, Francisco J. and Sch{\"o}ning, Michael Josef and Wang, Joseph}, title = {Epidermal tattoo potentiometric sodium sensors with wireless signal transduction for continuous non-invasive sweat monitoring}, series = {Biosensors and bioelectronics}, volume = {54}, journal = {Biosensors and bioelectronics}, publisher = {Elsevier}, address = {Amsterdam}, issn = {1873-4235 (E-Journal); 0956-5663 (Print)}, doi = {10.1016/j.bios.2013.11.039}, pages = {603 -- 609}, year = {2014}, abstract = {This article describes the fabrication, characterization and application of an epidermal temporary-transfer tattoo-based potentiometric sensor, coupled with a miniaturized wearable wireless transceiver, for real-time monitoring of sodium in the human perspiration. Sodium excreted during perspiration is an excellent marker for electrolyte imbalance and provides valuable information regarding an individual's physical and mental wellbeing. The realization of the new skin-worn non-invasive tattoo-like sensing device has been realized by amalgamating several state-of-the-art thick film, laser printing, solid-state potentiometry, fluidics and wireless technologies. The resulting tattoo-based potentiometric sodium sensor displays a rapid near-Nernstian response with negligible carryover effects, and good resiliency against various mechanical deformations experienced by the human epidermis. On-body testing of the tattoo sensor coupled to a wireless transceiver during exercise activity demonstrated its ability to continuously monitor sweat sodium dynamics. The real-time sweat sodium concentration was transmitted wirelessly via a body-worn transceiver from the sodium tattoo sensor to a notebook while the subjects perspired on a stationary cycle. The favorable analytical performance along with the wearable nature of the wireless transceiver makes the new epidermal potentiometric sensing system attractive for continuous monitoring the sodium dynamics in human perspiration during diverse activities relevant to the healthcare, fitness, military, healthcare and skin-care domains.}, language = {en} } @article{HeinzeMangPeteretal.2014, author = {Heinze, Daniel and Mang, Thomas and Peter, Karin and M{\"o}ller, Martin and Weichold, Oliver}, title = {Synthesis of low molecular weight poly(vinyl acetate) and its application as plasticizer}, series = {Journal of applied polymer science}, volume = {131}, journal = {Journal of applied polymer science}, number = {9}, publisher = {Wiley}, address = {New York}, issn = {1097-4628 (E-Journal); 0021-8995 (Print)}, doi = {10.1002/app.40226}, pages = {Article No. 40226}, year = {2014}, abstract = {Poly(vinyl acetate), PVAc, with a degree of polymerization Xn = 10 was prepared by chain-transfer radical polymerization using carbon tetrachloride and used as oligomeric plasticizer for commercial PVAc. However, the chlorinated chain ends cause a low thermal stability requiring mild Cl/H substitution. The product exhibits high thermal stability and excellent melt-compounding properties. Blends of oligomeric and commercial PVAc show single glass transition temperatures which decrease with higher oligomer content and exhibit small negative deviations from Fox' linear additivity rule. This indicates plasticization and miscibility being mainly due to entropic effects. Injection-moulded thick specimens show ductile behaviour at oligomer contents >10 wt \%, while sheets with a thickness of 0.2-0.5 mm appear flexible already at 7.5 wt \%. The oxygen permeability coefficients are an order of magnitude lower than those of low-density polyethylene. Due to the sum of their properties, the plasticized sheets present a promising alternative in the preparation of barrier materials.}, language = {en} } @article{Dikta2014, author = {Dikta, Gerhard}, title = {Asymptotically efficient estimation under semi-parametric random censorship models}, series = {Journal of multivariate analysis}, volume = {124}, journal = {Journal of multivariate analysis}, publisher = {Elsevier}, address = {Amsterdam}, issn = {1095-7243 (E-Journal); 0047-259X (Print)}, doi = {10.1016/j.jmva.2013.10.002}, pages = {10 -- 24}, year = {2014}, abstract = {We study the estimation of some linear functionals which are based on an unknown lifetime distribution. The observations are assumed to be generated under the semi-parametric random censorship model (SRCM), that is, a random censorship model where the conditional expectation of the censoring indicator given the observation belongs to a parametric family. Under this setup a semi-parametric estimator of the survival function was introduced by the author. If the parametric model assumption is correct, it is known that the estimated functional which is based on this semi-parametric estimator is asymptotically at least as efficient as the corresponding one which rests on the nonparametric Kaplan-Meier estimator. In this paper we show that the estimated functional which is based on this semi-parametric estimator is asymptotically efficient with respect to the class of all regular estimators under this semi-parametric model.}, language = {en} } @article{KronhardtAlexopoulosReisseletal.2014, author = {Kronhardt, Valentina and Alexopoulos, Spiros and Reißel, Martin and Sattler, Johannes, Christoph and Hoffschmidt, Bernhard and H{\"a}nel, Matthias and Doerbeck, Till}, title = {High-temperature thermal storage system for solar tower power plants with open-volumetric air receiver simulation and energy balancing of a discretized model}, series = {Energy procedia}, volume = {49}, journal = {Energy procedia}, publisher = {Elsevier}, address = {Amsterdam}, issn = {1876-6102 (E-Journal) ; 1876-6102 (Print)}, doi = {10.1016/j.egypro.2014.03.094}, pages = {870 -- 877}, year = {2014}, abstract = {This paper describes the modeling of a high-temperature storage system for an existing solar tower power plant with open volumetric receiver technology, which uses air as heat transfer medium (HTF). The storage system model has been developed in the simulation environment Matlab/Simulink®. The storage type under investigation is a packed bed thermal energy storage system which has the characteristics of a regenerator. Thermal energy can be stored and discharged as required via the HTF air. The air mass flow distribution is controlled by valves, and the mass flow by two blowers. The thermal storage operation strategy has a direct and significant impact on the energetic and economic efficiency of the solar tower power plants.}, language = {en} } @article{RauAlexopoulosBreitbachetal.2014, author = {Rau, Christoph and Alexopoulos, Spiros and Breitbach, Gerd and Hoffschmidt, Bernhard and Latzke, Markus and Sattler, Johannes, Christoph}, title = {Transient simulation of a solar-hybrid tower power plant with open volumetric receiver at the location Barstow}, series = {Energy procedia : proceedings of the SolarPACES 2013 International Conference}, volume = {49}, journal = {Energy procedia : proceedings of the SolarPACES 2013 International Conference}, publisher = {Elsevier}, address = {Amsterdam}, issn = {1876-6102}, doi = {10.1016/j.egypro.2014.03.157}, pages = {1481 -- 1490}, year = {2014}, abstract = {In this work the transient simulations of four hybrid solar tower power plant concepts with open-volumetric receiver technology for a location in Barstow-Daggett, USA, are presented. The open-volumetric receiver uses ambient air as heat transfer fluid and the hybridization is realized with a gas turbine. The Rankine cycle is heated by solar-heated air and/or by the gas turbine's flue gases. The plant can be operated in solar-only, hybrid parallel or combined cycle-only mode as well as in any intermediate load levels where the solar portion can vary between 0 to 100\%. The simulated plant is based on the configuration of a solar-hybrid power tower project, which is in planning for a site in Northern Algeria. The meteorological data for Barstow-Daggett was taken from the software meteonorm. The solar power tower simulation tool has been developed in the simulation environment MATLAB/Simulink and is validated.}, language = {en} } @book{BirleKleinMueller2014, author = {Birle, J{\"u}rgen P. and Klein, Hartmut and M{\"u}ller, Thomas}, title = {Praxishandbuch der GmbH : Gesellschafts- und Steuerrecht}, edition = {3. Aufl.}, publisher = {NWB-Verl.}, address = {Herne}, isbn = {978-3-482-56963-0}, pages = {1105 S.}, year = {2014}, language = {de} } @book{MuellerStoeckerLieber2014, author = {M{\"u}ller, Thomas and St{\"o}cker, Ernst E. and Lieber, Bettina}, title = {Die Organschaft : K{\"o}rperschaftsteuerrecht, Gewerbesteuerrecht, Umsatzsteuerrecht, Grunderwerbsteuerrecht}, edition = {9. Aufl.}, publisher = {NWB-Verl.}, address = {Herne}, isbn = {978-3-482-44609-2}, pages = {544 S.}, year = {2014}, language = {de} } @book{Berndt2014, author = {Berndt, Heinz}, title = {Neue Kondensations-Methoden zur Synthese definierter Peptid-Derivate}, address = {Aachen}, pages = {XII, VI, 207 S. : graph. Darst.}, year = {2014}, language = {de} } @misc{Alt2014, author = {Alt, Helmut}, title = {Energiekonzept mit kurzer Br{\"u}cke zu witterungsabh{\"a}ngigen, hohen Strompreisen : KTG Jahrestagung in Stuttgart, 22.- 24. 5. 2012}, pages = {1 -- 60}, year = {2014}, language = {de} } @article{MiyamotoItabashiWagneretal.2014, author = {Miyamoto, Ko-ichiro and Itabashi, Akinori and Wagner, Torsten and Sch{\"o}ning, Michael Josef and Yoshinobu, Tatsuo}, title = {High-speed chemical imaging inside a microfluidic channel}, series = {Sensors and actuators. B: Chemical}, volume = {194}, journal = {Sensors and actuators. B: Chemical}, publisher = {Elsevier}, address = {Amsterdam}, issn = {1873-3077 (E-Journal); 0925-4005 (Print)}, doi = {10.1016/j.snb.2013.12.090}, pages = {521 -- 527}, year = {2014}, abstract = {In this study, a high-speed chemical imaging system was developed for visualization of the interior of a microfluidic channel. A microfluidic channel was constructed on the sensor surface of the light-addressable potentiometric sensor (LAPS), on which the ion concentrations could be measured in parallel at up to 64 points illuminated by optical fibers. The temporal change of pH distribution inside the microfluidic channel was recorded at a maximum rate of 100 frames per second (fps). The high frame rate allowed visualization of moving interfaces and plugs in the channel even at a flow velocity of 111 mm/s, which suggests the feasibility of plug-based microfluidic devices for flow-injection analysis (FIA).}, language = {en} } @article{Laack2014, author = {Laack, Walter van}, title = {Nature is much smarter than expected: the Genetic Code is not degenerate}, series = {American journal of humanities and social sciences}, volume = {Vol. 2}, journal = {American journal of humanities and social sciences}, number = {No. 1}, issn = {2329-0781 (Print) ; 2329-079X (Online)}, pages = {10 -- 12}, year = {2014}, abstract = {In any books about genetics it can still today be read that our genetic code is called "degenerate" because it is still believed that 43 = 64 triplets encode the 20 essential amino acids. Indeed we have to assume the inverse law, what means that 34 = 81 exact code positions are really effective for our genetic code and encode the amino acids, compiled to proteins. This very important discovery leads to two completely new results that are limits-overlooking: 1) 34 (=81) genetic code positions mean exactly the same number as there are stable and naturally existing chemical elements in our universe. This famous argument should now lead to some alternative, as well as new fundamental conclusions about our existence. 2) A genetic code positioning system shows that nature is much smarter than expected: mutations are made less dangerous than believed, because they won't be that easily able any more to cause severe damages in the protein-synthesis. This should also lead to some alternative views upon evolution of life.}, language = {en} } @article{MoseleyHalamekKrameretal.2014, author = {Moseley, Fiona and Halamek, Jan and Kramer, Friederike and Poghossian, Arshak and Sch{\"o}ning, Michael Josef and Katz, Evgeny}, title = {An enzyme-based reversible CNOT logic gate realized in a flow system}, series = {Analyst}, volume = {139}, journal = {Analyst}, number = {8}, publisher = {Royal Society of Chemistry}, address = {Cambridge}, issn = {1364-5528 (E-Journal) ; 0003-2654 (Print)}, doi = {10.1039/C4AN00133H}, pages = {1839 -- 1842}, year = {2014}, abstract = {An enzyme system organized in a flow device was used to mimic a reversible Controlled NOT (CNOT) gate with two input and two output signals. Reversible conversion of NAD⁺ and NADH cofactors was used to perform a XOR logic operation, while biocatalytic hydrolysis of p-nitrophenyl phosphate resulted in an Identity operation working in parallel. The first biomolecular realization of a CNOT gate is promising for integration into complex biomolecular networks and future biosensor/biomedical applications.}, language = {en} } @article{GoedhuysJanzMohnen2014, author = {Goedhuys, Micheline and Janz, Norbert and Mohnen, Pierre}, title = {Knowledge-based productivity in "low-tech" industries: evidence from firms in developing countries}, series = {Industrial and corporate change}, volume = {23}, journal = {Industrial and corporate change}, number = {1}, publisher = {Oxford University Press}, address = {Oxford}, issn = {1464-3650 (E-Journal); 0960-6491 (Print)}, doi = {10.1093/icc/dtt006}, pages = {1 -- 23}, year = {2014}, abstract = {Using firm-level data from five developing countries—Brazil, Ecuador, South Africa, Tanzania, and Bangladesh—and three industries—food processing, textiles, and the garments and leather products—this article examines the importance of various sources of knowledge for explaining productivity and formally tests whether sector- or country-specific characteristics dominate these relationships. Knowledge sources driving productivity appear mainly sector specific. Also differences in the level of development affect the effectiveness of knowledge sources. In the food processing sector, firms with higher educated managers are more productive, and in least-developed countries, additionally those with technology licenses and imported machinery and equipment. In the capital-intensive textiles sector, productivity is higher in firms that conduct R\&D. In the garments and leather products sector, higher education of the managers, licensing, and R\&D raise productivity.}, language = {en} } @incollection{WolffSeefeldtBaueretal.2014, author = {Wolff, Nino and Seefeldt, Patric and Bauer, Wolfgang and Fiebig, Christopher and Gerding, Patrick and Parow-Souchon, Kai and Pongs, Anna and Reiffenrath, Matti and Ziemann, Thomas}, title = {Alternative application of solar sail technology}, series = {Advances in solar sailing}, booktitle = {Advances in solar sailing}, publisher = {Springer}, address = {Berlin}, isbn = {978-3-642-34906-5 (Print) ; 978-3-642-34907-2 (E-Book)}, doi = {10.1007/978-3-642-34907-2_23}, pages = {351 -- 365}, year = {2014}, abstract = {The development of Gossamer sail structures for solar sails contributes to a large field of future space applications like thin film solar generators, membrane antennas and drag sails. The focus of this paper is the development of a drag sail based on solar sail technology that could contribute to a reduction of space debris in low Earth orbits. The drag sail design and its connections to solar sail development, a first test on a sounding rocket, as well as the ongoing integration of the drag sail into a triple CubeSat is presented.}, language = {en} } @incollection{DachwaldBoehnhardtBrojetal.2014, author = {Dachwald, Bernd and Boehnhardt, Herrmann and Broj, Ulrich and Geppert, Ulrich R. M. E. and Grundmann, Jan-Thimo and Seboldt, Wolfgang and Seefeldt, Patric and Spietz, Peter and Johnson, Les and K{\"u}hrt, Ekkehard and Mottola, Stefano and Macdonald, Malcolm and McInnes, Colin R. and Vasile, Massimiliano and Reinhard, Ruedeger}, title = {Gossamer roadmap technology reference study for a multiple NEO Rendezvous Mission}, series = {Advances in solar sailing}, booktitle = {Advances in solar sailing}, publisher = {Springer}, address = {Berlin [u.a.]}, isbn = {978-3-642-34906-5 (Print) ; 978-3-642-34907-2 (E-Book)}, pages = {211 -- 226}, year = {2014}, abstract = {A technology reference study for a multiple near-Earth object (NEO) rendezvous mission with solar sailcraft is currently carried out by the authors of this paper. The investigated mission builds on previous concepts, but adopts a strong micro-spacecraft philosophy based on the DLR/ESA Gossamer technology. The main scientific objective of the mission is to explore the diversity of NEOs. After direct interplanetary insertion, the solar sailcraft should—within less than 10 years—rendezvous three NEOs that are not only scientifically interesting, but also from the point of human spaceight and planetary defense. In this paper, the objectives of the study are outlined and a preliminary potential mission profile is presented.}, language = {en} } @incollection{McInnesBothmerDachwaldetal.2014, author = {McInnes, Colin R. and Bothmer, Volker and Dachwald, Bernd and Geppert, Ulrich R. M. E. and Heiligers, Jeannette and Hilgers, Alan and Johnson, Les and Macdonald, Malcolm and Reinhard, Ruedeger and Seboldt, Wolfgang and Spietz, Peter}, title = {Gossamer roadmap technology reference study for a Sub-L1 Space Weather Mission}, series = {Advances in solar sailing}, booktitle = {Advances in solar sailing}, publisher = {Springer}, address = {Berlin [u.a.]}, isbn = {978-3-642-34906-5 (Print) ; 978-3-642-34907-2 (E-Book)}, pages = {227 -- 242}, year = {2014}, abstract = {A technology reference study for a displaced Lagrange point space weather mission is presented. The mission builds on previous concepts, but adopts a strong micro-spacecraft philosophy to deliver a low mass platform and payload which can be accommodated on the DLR/ESA Gossamer-3 technology demonstration mission. A direct escape from Geostationary Transfer Orbit is assumed with the sail deployed after the escape burn. The use of a miniaturized, low mass platform and payload then allows the Gossamer-3 solar sail to potentially double the warning time of space weather events. The mission profile and mass budgets will be presented to achieve these ambitious goals.}, language = {en} } @incollection{MacdonaldMcGrathAppourchauxetal.2014, author = {Macdonald, Malcolm and McGrath, C. and Appourchaux, T. and Dachwald, Bernd and Finsterle, W. and Gizon, L. and Liewer, P. C. and McInnes, Colin R. and Mengali, G. and Seboldt, W. and Sekii, T. and Solanki, S. K. and Velli, M. and Wimmer-Schweingruber, R. F. and Spietz, Peter and Reinhard, Ruedeger}, title = {Gossamer roadmap technology reference study for a solar polar mission}, series = {Advances in solar sailing}, booktitle = {Advances in solar sailing}, editor = {Macdonald, Malcolm}, publisher = {Springer}, address = {Berlin, Heidelberg}, isbn = {978-3-642-34906-5}, doi = {10.1007/978-3-642-34907-2_17}, pages = {243 -- 257}, year = {2014}, abstract = {A technology reference study for a solar polar mission is presented. The study uses novel analytical methods to quantify the mission design space including the required sail performance to achieve a given solar polar observation angle within a given timeframe and thus to derive mass allocations for the remaining spacecraft sub-systems, that is excluding the solar sail sub-system. A parametric, bottom-up, system mass budget analysis is then used to establish the required sail technology to deliver a range of science payloads, and to establish where such payloads can be delivered to within a given timeframe. It is found that a solar polar mission requires a solar sail of side-length 100-125 m to deliver a 'sufficient value' minimum science payload, and that a 2.5 μm sail film substrate is typically required, however the design is much less sensitive to the boom specific mass.}, language = {en} } @inproceedings{HartungHillgaertnerSchmitzetal.2014, author = {Hartung, Frank and Hillg{\"a}rtner, Michael and Schmitz, G{\"u}nter and Schuba, Marko and Adolphs, Fabian and Hoffend, Jens and Theis, Jochen}, title = {IT-Sicherheit im Automobil}, series = {AmE 2014 : Automotive meets Electronics, Beitr{\"a}ge der 5. GMM-Fachtagung vom 18. bis 19. Februar 2014 in Dortmund. (GMM-Fachbericht ; 78)}, booktitle = {AmE 2014 : Automotive meets Electronics, Beitr{\"a}ge der 5. GMM-Fachtagung vom 18. bis 19. Februar 2014 in Dortmund. (GMM-Fachbericht ; 78)}, publisher = {VDE-Verl.}, address = {Berlin}, organization = {VDE/VDI-Gesellschaft Mikroelektronik, Mikrosystem- und Feinwerktechnik (GMM)}, isbn = {978-3-8007-3580-8}, pages = {CD-ROM}, year = {2014}, language = {de} } @misc{Ritz2014, author = {Ritz, Thomas}, title = {Multiplattformentwicklung f{\"u}r mobile Informationssysteme : eine strategische Perspektive}, series = {Info-Veranstaltung Multiplattform-Entwicklung f{\"u}r mobile Anwendungen, Dezember 2013}, journal = {Info-Veranstaltung Multiplattform-Entwicklung f{\"u}r mobile Anwendungen, Dezember 2013}, organization = {FH Aachen, University of Applied Sciences / m2clab}, pages = {1 Video (Laufzeit: 23:57 Min.)}, year = {2014}, language = {de} } @misc{Ritz2014, author = {Ritz, Thomas}, title = {Multiplattformentwicklung f{\"u}r mobile Informationssysteme : eine strategische Perspektive ; [Vortragsfolien]}, series = {Info-Veranstaltung Multiplattform-Entwicklung f{\"u}r mobile Entwicklungen, Dezember 2013}, journal = {Info-Veranstaltung Multiplattform-Entwicklung f{\"u}r mobile Entwicklungen, Dezember 2013}, organization = {eBusinessLotse, Infob{\"u}ro f{\"u}r Unternehmen, Aachen}, pages = {13 S. : Ill., graph. Darst.}, year = {2014}, language = {de} } @article{WangDruckenmuellerElbersetal.2014, author = {Wang, Ren-Qi and Druckenm{\"u}ller, Katharina and Elbers, Gereon and Guenther, Klaus and Crou{\´e}, Jean-Philippe}, title = {Analysis of aquatic-phase natural organic matter by optimized LDI-MS method}, series = {Journal of mass spectrometry}, volume = {49}, journal = {Journal of mass spectrometry}, number = {2}, publisher = {Wiley}, address = {Bognor Regis}, issn = {1096-9888}, doi = {10.1002/jms.3321}, pages = {154 -- 160}, year = {2014}, abstract = {The composition and physiochemical properties of aquatic-phase natural organic matter (NOM) are most important problems for both environmental studies and water industry. Laser desorption/ionization (LDI) mass spectrometry facilitated successful examinations of NOM, as humic and fulvic acids in NOM are readily ionized by the nitrogen laser. In this study, hydrophobic NOMs (HPO NOMs) from river, reservoir and waste water were characterized by this technique. The effect of analytical variables like concentration, solvent composition and laser energy was investigated. The exact masses of small molecular NOM moieties in the range of 200-1200 m/z were determined in reflectron mode. In addition, spectra of post-source-decay experiments in this range showed that some compounds from different natural NOMs had the same fragmental ions. In the large mass range of 1200-15 000 Da, macromolecules and their aggregates were found in HPO NOMs from natural waters. Highly humic HPO exhibited mass peaks larger than 8000 Da. On the other hand, the waste water and reservoir water mainly had relatively smaller molecules of about 2000 Da. The LDI-MS measurements indicated that highly humic river waters were able to form large aggregates and membrane foulants, while the HPO NOMs from waste water and reservoir water were unlikely to form large aggregates. Copyright © 2014 John Wiley \& Sons, Ltd.}, language = {en} } @article{SchroeterHoffmannVoigtetal.2014, author = {Schroeter, Rebecca and Hoffmann, Tamara and Voigt, Birgit and Meyer, Hanna and Bleisteiner, Monika and Muntel, Jan and J{\"u}rgen, Britta and Albrecht, Dirk and Becher, D{\"o}rte and Lalk, Michael and Evers, Stefan and Bongaerts, Johannes and Maurer, Karl-Heinz and Putzer, Harald and Hecker, Michael and Schweder, Thomas and Bremer, Erhard}, title = {Stress responses of the industrial workhorse Bacillus licheniformis to osmotic challenges}, series = {PLoS ONE}, volume = {8}, journal = {PLoS ONE}, number = {11}, publisher = {PLOS}, address = {San Francisco}, issn = {1932-6203}, doi = {10.1371/journal.pone.0080956}, pages = {Article No. e80956}, year = {2014}, abstract = {The Gram-positive endospore-forming bacterium Bacillus licheniformis can be found widely in nature and it is exploited in industrial processes for the manufacturing of antibiotics, specialty chemicals, and enzymes. Both in its varied natural habitats and in industrial settings, B. licheniformis cells will be exposed to increases in the external osmolarity, conditions that trigger water efflux, impair turgor, cause the cessation of growth, and negatively affect the productivity of cell factories in biotechnological processes. We have taken here both systems-wide and targeted physiological approaches to unravel the core of the osmostress responses of B. licheniformis. Cells were suddenly subjected to an osmotic upshift of considerable magnitude (with 1 M NaCl), and their transcriptional profile was then recorded in a time-resolved fashion on a genome-wide scale. A bioinformatics cluster analysis was used to group the osmotically up-regulated genes into categories that are functionally associated with the synthesis and import of osmostress-relieving compounds (compatible solutes), the SigB-controlled general stress response, and genes whose functional annotation suggests that salt stress triggers secondary oxidative stress responses in B. licheniformis. The data set focusing on the transcriptional profile of B. licheniformis was enriched by proteomics aimed at identifying those proteins that were accumulated by the cells through increased biosynthesis in response to osmotic stress. Furthermore, these global approaches were augmented by a set of experiments that addressed the synthesis of the compatible solutes proline and glycine betaine and assessed the growth-enhancing effects of various osmoprotectants. Combined, our data provide a blueprint of the cellular adjustment processes of B. licheniformis to both sudden and sustained osmotic stress.}, language = {en} } @book{FredebeulKreinKochKulessaetal.2014, author = {Fredebeul-Krein, Markus and Koch, Walter A. S. and Kulessa, Margareta and Sputek, Agnes}, title = {Grundlagen der Wirtschaftspolitik}, edition = {4. Aufl.}, publisher = {UVK Verl.-Ges.}, address = {Konstanz [u.a.]}, isbn = {978-3-8252-8556-2}, pages = {508 S.}, year = {2014}, language = {de} } @article{ArinkinDigelPorstetal.2014, author = {Arinkin, Vladimir and Digel, Ilya and Porst, Dariusz and Temiz Artmann, Ayseg{\"u}l and Artmann, Gerhard}, title = {Phenotyping date palm varieties via leaflet cross-sectional imaging and artificial neural network application}, series = {BMC bioinformatics}, volume = {15}, journal = {BMC bioinformatics}, number = {55}, issn = {1471-2105}, doi = {10.1186/1471-2105-15-55}, pages = {1 -- 8}, year = {2014}, abstract = {Background True date palms (Phoenix dactylifera L.) are impressive trees and have served as an indispensable source of food for mankind in tropical and subtropical countries for centuries. The aim of this study is to differentiate date palm tree varieties by analysing leaflet cross sections with technical/optical methods and artificial neural networks (ANN). Results Fluorescence microscopy images of leaflet cross sections have been taken from a set of five date palm tree cultivars (Hewlat al Jouf, Khlas, Nabot Soltan, Shishi, Um Raheem). After features extraction from images, the obtained data have been fed in a multilayer perceptron ANN with backpropagation learning algorithm. Conclusions Overall, an accurate result in prediction and differentiation of date palm tree cultivars was achieved with average prediction in tenfold cross-validation is 89.1\% and reached 100\% in one of the best ANN.}, language = {en} } @article{SawadaNakazawaTakenagaetal.2014, author = {Sawada, Kazuaki and Nakazawa, Hirokazu and Takenaga, Shoko and Hizawa, Takeshi and Futagawa, Masato and Dasai, Fumihiro and Sakurai, Takashi and Okumura, Koichi and Hattori, Toshiaki and Ishida, Makoto}, title = {Multimodal bioimage sensor}, series = {IEICE transactions on fundamentals of electronics, communidations and computer sciences}, volume = {E97-A (2014)}, journal = {IEICE transactions on fundamentals of electronics, communidations and computer sciences}, number = {3}, publisher = {IEICE}, address = {Tokyo}, issn = {0916-8508 (Print) ; 1745-1337 (Online)}, doi = {10.1587/transfun.E97.A.726}, pages = {726 -- 733}, year = {2014}, abstract = {To visualize the biochemical distribution two-dimensionally, we invented a solid-state-type ion image sensor that indicates the chemical activity of solutions and cells. The device, which consists of a CCD array covered with a functionalized membrane to detect charge accumulation, is highly sensitive to changes in the concentration and two-dimensional distribution of ions and biomaterials.}, language = {en} } @article{LeinhosSchusserBaeckeretal.2014, author = {Leinhos, Marcel and Schusser, Sebastian and B{\"a}cker, Matthias and Poghossian, Arshak and Sch{\"o}ning, Michael Josef}, title = {Micromachined multi-parameter sensor chip for the control of polymer-degradation medium}, series = {Physica Status Solidi (A) : special issue on engineering and functional interfaces}, volume = {211}, journal = {Physica Status Solidi (A) : special issue on engineering and functional interfaces}, number = {6}, publisher = {Wiley-VCH}, address = {Weinheim}, issn = {1521-396X (E-Journal); 1862-6319 (E-Journal); 0031-8965 (Print); 1862-6300 (Print)}, doi = {10.1002/pssa.201330364}, pages = {1346 -- 1351}, year = {2014}, abstract = {It is well known that the degradation environment can strongly influence the biodegradability and kinetics of biodegradation processes of polymers. Therefore, besides the monitoring of the degradation process, it is also necessary to control the medium in which the degradation takes place. In this work, a micromachined multi-parameter sensor chip for the control of the polymer-degradation medium has been developed. The chip combines a capacitive field-effect pH sensor, a four-electrode electrolyte-conductivity sensor and a thin-film Pt-temperature sensor. The results of characterization of individual sensors are presented. In addition, the multi-parameter sensor chip together with an impedimetric polymer-degradation sensor was simultaneously characterized in degradation solutions with different pH and electrolyte conductivity. The obtained results demonstrate the feasibility of the multi-parameter sensor chip for the control of the polymer-degradation medium.}, language = {en} } @incollection{SchoeningPoghossianGluecketal.2014, author = {Sch{\"o}ning, Michael Josef and Poghossian, Arshak and Gl{\"u}ck, Olaf and Thust, Marion}, title = {Electrochemical composition measurement}, series = {Measurement, instrumentation, and sensors handbook: electromagnetic, optical, radiation, chemical, and biomedical measuremen}, booktitle = {Measurement, instrumentation, and sensors handbook: electromagnetic, optical, radiation, chemical, and biomedical measuremen}, edition = {2nd ed.}, publisher = {CRC Pr.}, address = {Boca Raton, Fa.}, isbn = {978-1-4398-4891-3}, pages = {55-1 -- 55-54}, year = {2014}, language = {en} } @article{HeineHerrmannSelmeretal.2014, author = {Heine, A. and Herrmann, G. and Selmer, Thorsten and Terwesten, F. and Buckel, W. and Reuter, K.}, title = {High resolution crystal structure of clostridium propionicum β-Alanyl-CoA:Ammonia Lyase, a new member of the "Hot Dog Fold" protein superfamily}, series = {Proteins}, volume = {82}, journal = {Proteins}, number = {9}, publisher = {Wiley-Liss}, address = {New York}, issn = {1097-0134 (E-Journal); 0887-3585 (Print)}, doi = {10.1002/prot.24557}, pages = {2041 -- 2053}, year = {2014}, abstract = {Clostridium propionicum is the only organism known to ferment β-alanine, a constituent of coenzyme A (CoA) and the phosphopantetheinyl prosthetic group of holo-acyl carrier protein. The first step in the fermentation is a CoA-transfer to β-alanine. Subsequently, the resulting β-alanyl-CoA is deaminated by the enzyme β-alanyl-CoA:ammonia lyase (Acl) to reversibly form ammonia and acrylyl-CoA. We have determined the crystal structure of Acl in its apo-form at a resolution of 0.97 {\AA} as well as in complex with CoA at a resolution of 1.59 {\AA}. The structures reveal that the enyzme belongs to a superfamily of proteins exhibiting a so called "hot dog fold" which is characterized by a five-stranded antiparallel β-sheet with a long α-helix packed against it. The functional unit of all "hot dog fold" proteins is a homodimer containing two equivalent substrate binding sites which are established by the dimer interface. In the case of Acl, three functional dimers combine to a homohexamer strongly resembling the homohexamer formed by YciA-like acyl-CoA thioesterases. Here, we propose an enzymatic mechanism based on the crystal structure of the Acl·CoA complex and molecular docking. Proteins 2014; 82:2041-2053. © 2014 Wiley Periodicals, Inc.}, language = {en} } @article{HuckPoghossianKerroumietal.2014, author = {Huck, Christina and Poghossian, Arshak and Kerroumi, Iman and Schusser, Sebastian and B{\"a}cker, Matthias and Zander, Willi and Schubert, J{\"u}rgen and Buniatyan, Vahe V. and Martirosyan, Norayr W. and Wagner, Patrick and Sch{\"o}ning, Michael Josef}, title = {Multiparameter sensor chip with Barium Strontium Titanate as multipurpose material}, series = {Electroanalysis}, volume = {26}, journal = {Electroanalysis}, number = {5}, publisher = {Wiley-VCH}, address = {Weinheim}, issn = {1521-4109 (E-Journal); 1040-0397 (Print)}, doi = {10.1002/elan.201400076}, pages = {980 -- 987}, year = {2014}, abstract = {It is well known that biochemical and biotechnological processes are strongly dependent and affected by a variety of physico-chemical parameters such as pH value, temperature, pressure and electrolyte conductivity. Therefore, these quantities have to be monitored or controlled in order to guarantee a stable process operation, optimization and high yield. In this work, a sensor chip for the multiparameter detection of three physico-chemical parameters such as electrolyte conductivity, pH and temperature is realized using barium strontium titanate (BST) as multipurpose material. The chip integrates a capacitively coupled four-electrode electrolyte-conductivity sensor, a capacitive field-effect pH sensor and a thin-film Pt-temperature sensor. Due to the multifunctional properties of BST, it is utilized as final outermost coating layer of the processed sensor chip and serves as passivation and protection layer as well as pH-sensitive transducer material at the same time. The results of testing of the individual sensors of the developed multiparameter sensor chip are presented. In addition, a quasi-simultaneous multiparameter characterization of the sensor chip in buffer solutions with different pH value and electrolyte conductivity is performed. To study the sensor behavior and the suitability of BST as multifunctional material under harsh environmental conditions, the sensor chip was exemplarily tested in a biogas digestate.}, language = {en} } @article{BaeckerKramerHucketal.2014, author = {B{\"a}cker, Matthias and Kramer, F. and Huck, Christina and Poghossian, Arshak and Bratov, A. and Abramova, N. and Sch{\"o}ning, Michael Josef}, title = {Planar and 3D interdigitated electrodes for biosensing applications: The impact of a dielectric barrier on the sensor properties}, series = {Physica Status Solidi (A) - Applications and Materials Science}, volume = {211}, journal = {Physica Status Solidi (A) - Applications and Materials Science}, number = {6}, publisher = {Wiley-VCH}, address = {Weinheim}, issn = {1521-396X (E-Journal); 1862-6319 (E-Journal); 0031-8965 (Print); 1862-6300 (Print)}, doi = {10.1002/pssa.201330416}, pages = {1357 -- 1363}, year = {2014}, abstract = {Planar and three-dimensional (3D) interdigitated electrodes (IDE) with electrode digits separated by an insulating barrier of different heights were electrochemically characterized and compared in terms of their sensing properties. Due to the impact of the surface resistance, both types of IDE structures display a non-linear behavior in low-ionic strength solutions. The experimental data were fitted to an electrical equivalent circuit and interpreted taking into account the surface-charge-governed properties. The effect of a charged polyelectrolyte layer electrostatically assembled onto the sensor surface on the surface resistance in solutions with different KCl concentration is studied. In case of the same electrode footprint, 3D-IDEs show a larger cell constant and a higher sensitivity to molecular adsorption than that of planar IDEs. The obtained results demonstrate the potential of 3D-IDEs as a new transducer structure for a direct label-free sensing of charged molecules.}, language = {en} } @article{FunkeDickhoffKeinzetal.2014, author = {Funke, Harald and Dickhoff, J. and Keinz, Jan and Anis, H. A. and Parente, A. and Hendrick, P.}, title = {Experimental and numerical study of the micromix combustion principle applied for hydrogen and hydrogen-rich syngas as fuel with increased energy density for industrial gas turbine applications}, series = {Energy procedia}, journal = {Energy procedia}, number = {61}, publisher = {Elsevier}, address = {Amsterdam}, issn = {1876-6102 (E-Journal)}, doi = {10.1016/j.egypro.2014.12.201}, pages = {1736 -- 1739}, year = {2014}, abstract = {The Dry Low NOx (DLN) Micromix combustion principle with increased energy density is adapted for the industrial gas turbine APU GTCP 36-300 using hydrogen and hydrogen-rich syngas with a composition of 90\%-Vol. hydrogen (H₂) and 10\%-Vol. carbon-monoxide (CO). Experimental and numerical studies of several combustor geometries for hydrogen and syngas show the successful advance of the DLN Micromix combustion from pure hydrogen to hydrogen-rich syngas. The impact of the different fuel properties on the combustion principle and aerodynamic flame stabilization design laws, flow field, flame structure and emission characteristics is investigated by numerical analysis using a hybrid Eddy Break Up combustion model and validated against experimental results.}, language = {en} } @article{HuckPoghossianBaeckeretal.2014, author = {Huck, Christina and Poghossian, Arshak and B{\"a}cker, Matthias and Chaudhuri, S. and Zander, W. and Schubert, J. and Begoyan, V. K. and Buniatyan, V. V. and Wagner, P. and Sch{\"o}ning, Michael Josef}, title = {Capacitively coupled electrolyte-conductivity sensor based on high-k material of barium strontium titanate}, series = {Sensors and actuators. B: Chemical}, journal = {Sensors and actuators. B: Chemical}, number = {198}, publisher = {Elsevier}, address = {Amsterdam}, issn = {1873-3077 (E-Journal); 0925-4005 (Print)}, doi = {10.1016/j.snb.2014.02.103}, pages = {102 -- 109}, year = {2014}, language = {en} } @article{Frings2014, author = {Frings, Michael}, title = {Das Gesetz gegen unseri{\"o}se Gesch{\"a}ftspraktiken}, series = {NWB : NWB Steuer- und Wirtschaftsrecht}, journal = {NWB : NWB Steuer- und Wirtschaftsrecht}, number = {11}, publisher = {NWB-Verlag}, address = {Herne}, issn = {0028-3460 (Print)}, pages = {769 -- 775}, year = {2014}, language = {de} } @article{Frings2014, author = {Frings, Michael}, title = {Neuregelung des Verbraucherschutzes - Umsetzung der EU-Verbraucherrechterichtlinie}, series = {NWB : NWB Steuer- und Wirtschaftsrecht}, journal = {NWB : NWB Steuer- und Wirtschaftsrecht}, number = {14}, publisher = {NWB-Verlag}, address = {Herne}, issn = {0028-3460 (Print)}, pages = {1003 -- 1018}, year = {2014}, language = {de} } @article{HandtkeSchroeterJuergenetal.2014, author = {Handtke, Stefan and Schroeter, Rebecca and J{\"u}rgen, Britta and Methling, Karen and Schl{\"u}ter, Rabea and Albrecht, Dirk and Hijum, Sacha A. F. T. van and Bongaerts, Johannes and Maurer, Karl-Heinz and Lalk, Michael and Schweder, Thomas and Hecker, Michael and Voigt, Birgit}, title = {Bacillus pumilus reveals a remarkably high resistance to hydrogen peroxide provoked oxidative stress}, series = {PLOS one}, volume = {2014}, journal = {PLOS one}, publisher = {PLOS}, address = {San Francisco}, issn = {1932-6203}, doi = {10.1371/journal.pone.0085625}, pages = {Publ. online}, year = {2014}, abstract = {Bacillus pumilus is characterized by a higher oxidative stress resistance than other comparable industrially relevant Bacilli such as B. subtilis or B. licheniformis. In this study the response of B. pumilus to oxidative stress was investigated during a treatment with high concentrations of hydrogen peroxide at the proteome, transcriptome and metabolome level. Genes/proteins belonging to regulons, which are known to have important functions in the oxidative stress response of other organisms, were found to be upregulated, such as the Fur, Spx, SOS or CtsR regulon. Strikingly, parts of the fundamental PerR regulon responding to peroxide stress in B. subtilis are not encoded in the B. pumilus genome. Thus, B. pumilus misses the catalase KatA, the DNA-protection protein MrgA or the alkyl hydroperoxide reductase AhpCF. Data of this study suggests that the catalase KatX2 takes over the function of the missing KatA in the oxidative stress response of B. pumilus. The genome-wide expression analysis revealed an induction of bacillithiol (Cys-GlcN-malate, BSH) relevant genes. An analysis of the intracellular metabolites detected high intracellular levels of this protective metabolite, which indicates the importance of bacillithiol in the peroxide stress resistance of B. pumilus.}, language = {en} } @book{Laack2014, author = {Laack, Walter van}, title = {Schnittstelle Tod: Was spricht f{\"u}r unser Weiterleben?}, publisher = {van Laack}, address = {Aachen}, isbn = {978-3-936624-19-9}, pages = {100 S.}, year = {2014}, language = {de} } @article{BeckBuchleitnerFerreinetal.2014, author = {Beck, Daniel and Buchleitner, Martin and Ferrein, Alexander and Niem{\"u}ller, Tim and Steinbauer, Gerald}, title = {Mostly Harmless \& AllemaniACs - mixed innovations}, pages = {1 -- 8}, year = {2014}, language = {en} } @article{SchirraWatmuffBauschat2014, author = {Schirra, Julian and Watmuff, Jonathan and Bauschat, J.-Michael}, title = {Highly non-planar lifting systems: a relative assessment of existing potential-methodologies to accurately estimate the induced drag}, series = {32nd AIAA Applied Aerodynamics Conference 2014 : June, 16-20 2014, Atlanta, Ga.}, journal = {32nd AIAA Applied Aerodynamics Conference 2014 : June, 16-20 2014, Atlanta, Ga.}, organization = {American Institute of Aeronautics and Astronautics}, isbn = {978-1-62410-288-2}, doi = {10.2514/6.2014-2988}, pages = {Publ. online}, year = {2014}, language = {en} } @inproceedings{FrotscherKochRaatschenetal.2014, author = {Frotscher, Ralf and Koch, Jan-Peter and Raatschen, Hans-J{\"u}rgen and Staat, Manfred}, title = {Evaluation of a computational model for drug action on cardiac tissue}, series = {11th World Congress on Computational Mechanics (WCCM XI) ; 5th European Conference on Computational Mechanics (ECCM V) ; 6th European Conference on Computational Fluid Dynamics (ECFD VI) ; July 20 - 25, 2014, Barcelona}, booktitle = {11th World Congress on Computational Mechanics (WCCM XI) ; 5th European Conference on Computational Mechanics (ECCM V) ; 6th European Conference on Computational Fluid Dynamics (ECFD VI) ; July 20 - 25, 2014, Barcelona}, editor = {Onate, E.}, organization = {World Congress on Computational Mechanics <11, 2014, Barcelona>}, pages = {1 -- 12}, year = {2014}, language = {en} } @inproceedings{JungStaatMueller2014, author = {Jung, Alexander and Staat, Manfred and M{\"u}ller, Wolfram}, title = {Optimization of the flight style in ski jumping}, series = {11th World Congress on Computational Mechanics (WCCM XI) ; 5th European Conference on Computational Mechanics (ECCM V) ; 6th European Conference on Computational Fluid Dynamics (ECFD VI) ; July 20 - 25, 2014, Barcelona}, booktitle = {11th World Congress on Computational Mechanics (WCCM XI) ; 5th European Conference on Computational Mechanics (ECCM V) ; 6th European Conference on Computational Fluid Dynamics (ECFD VI) ; July 20 - 25, 2014, Barcelona}, editor = {Onate, E.}, organization = {World Congress on Computational Mechanics <11, 2014, Barcelona>}, pages = {799 -- 810}, year = {2014}, language = {en} } @inproceedings{BhattaraiFrotscherSoraetal.2014, author = {Bhattarai, Aroj and Frotscher, Ralf and Sora, M.-C. and Staat, Manfred}, title = {A 3D finite element model of the female pelvic floor for the reconstruction of urinary incontinence}, series = {11th World Congress on Computational Mechanics (WCCM XI) ; 5th European Conference on Computational Mechanics (ECCM V) ; 6th European Conference on Computational Fluid Dynamics (ECFD VI) ; July 20-25, 2014, Barcelona}, booktitle = {11th World Congress on Computational Mechanics (WCCM XI) ; 5th European Conference on Computational Mechanics (ECCM V) ; 6th European Conference on Computational Fluid Dynamics (ECFD VI) ; July 20-25, 2014, Barcelona}, editor = {Onate, E.}, organization = {World Congress on Computational Mechanics <11, 2014, Barcelona>}, pages = {1 -- 12}, year = {2014}, language = {en} } @inproceedings{TranStaat2014, author = {Tran, Thanh Ngoc and Staat, Manfred}, title = {Uncertain multimode failure and limit analysis of shells}, series = {11th World Congress on Computational Mechanics (WCCM XI) ; 5th European Conference on Computational Mechanics (ECCM V) ; 6th European Conference on Computational Fluid Dynamics (ECFD VI) ; July 20-25, 2014, Barcelona}, booktitle = {11th World Congress on Computational Mechanics (WCCM XI) ; 5th European Conference on Computational Mechanics (ECCM V) ; 6th European Conference on Computational Fluid Dynamics (ECFD VI) ; July 20-25, 2014, Barcelona}, editor = {Onate, E.}, organization = {World Congress on Computational Mechanics <11, 2014, Barcelona>}, pages = {1 -- 12}, year = {2014}, language = {en} } @inproceedings{DuongStaat2014, author = {Duong, Minh Tuan and Staat, Manfred}, title = {A face-based smoothed finite element method for hyperelastic models and tissue growth}, series = {11th World Congress on Computational Mechanics (WCCM XI) ; 5th European Conference on Computational Mechanics (ECCM V) ; 6th European Conference on Computational Fluid Dynamics (ECFD VI) ; July 20-25, 2014, Barcelona}, booktitle = {11th World Congress on Computational Mechanics (WCCM XI) ; 5th European Conference on Computational Mechanics (ECCM V) ; 6th European Conference on Computational Fluid Dynamics (ECFD VI) ; July 20-25, 2014, Barcelona}, editor = {Onate, E.}, organization = {World Congress on Computational Mechanics <11, 2014, Barcelona>}, pages = {1 -- 12}, year = {2014}, language = {en} } @inproceedings{TranStaatStavroulakis2014, author = {Tran, Ngoc Trinh and Staat, Manfred and Stavroulakis, G. E.}, title = {A multicriteria method for truss optimization}, series = {11th World Congress on Computational Mechanics (WCCM XI) ; 5th European Conference on Computational Mechanics (ECCM V) ; 6th European Conference on Computational Fluid Dynamics (ECFD VI) ; July 20-25, 2014, Barcelona}, booktitle = {11th World Congress on Computational Mechanics (WCCM XI) ; 5th European Conference on Computational Mechanics (ECCM V) ; 6th European Conference on Computational Fluid Dynamics (ECFD VI) ; July 20-25, 2014, Barcelona}, editor = {Onate, E.}, organization = {World Congress on Computational Mechanics <11, 2014, Barcelona>}, pages = {1 -- 12}, year = {2014}, language = {en} } @article{MansurovJandosovKerimkulovaetal.2014, author = {Mansurov, Z. A. and Jandosov, J. M. and Kerimkulova, A. R. and Azat, S. and Zhubanova, A. A. and Digel, Ilya and Savistkaya, I. S. and Akimbekov, N. S. and Kistaubaeva, A. S.}, title = {Nanostructured carbon materials for biomedical use}, series = {Eurasian chemico-technological journal : quarterly journal of the International Higher Education Academy of Sciences}, volume = {15 (2013)}, journal = {Eurasian chemico-technological journal : quarterly journal of the International Higher Education Academy of Sciences}, number = {3}, publisher = {Institute of Combustion Problems}, address = {Almaty}, issn = {1562-3920}, doi = {10.18321/ectj224}, pages = {209 -- 217}, year = {2014}, abstract = {One of the priority trends of carbon nanotechnology is creation of nanocomposite systems. Such carbon nanostructured composites were produced using - raw materials based on the products of agricultural waste, such as grape stones, apricot stones, rice husk. These products have a - wide spectrum of application and can be obtained in large quantities. The Institute of Combustion Problems has carried out the work on synthesis of the nanostructured carbon sorbents for multiple applications including the field of biomedicine. The article presents the data on the synthesis and physico-chemical properties of carbonaceous sorbents using physicochemical methods of investigation: separation and purification of biomolecules; isolation of phytohormone - fusicoccin; adsorbent INGO-1 in the form of an adsorption column for blood detoxification, oral (entero) sorbent - INGO-2; the study of efferent and probiotic properties and sorption activity in regard to the lipopolysaccharide (LPS), new biocomposites - based on carbonized rice husk (CRH) and cellular microorganisms; the use of CRH in wound treatment. A new material for blood detoxication (INGO-1) has been obtained. Adsorption of p-cresyl sulfate and indoxyl sulfate has shown that active carbon adsorbent can remove clinically significant level of p-cresyl sulfate and indoxyl sulfate from human plasma. Enterosorbent INGO-2 possesses high adsorption activity in relation to Gram-negative bacteria and their endotoxins. INGO-2 slows down the growth of conditionally pathogenic microorganisms, without having a negative effect on bifido and lactobacteria. The use of enterosorbent INGO-2 for sorption therapy may provide a solution to a complex problem - detoxication of the digestive tract and normalization of the intestinal micro ecology. The immobilized probiotic called "Riso-lact" was registered at the Ministry of Health of the Republic of Kazakhstan as a biologically active food additive. The developed technology is patented and provides production of the medicine in the form of freeze-dried biomass immobilized in vials.}, language = {en} } @article{WolfBiesenGreeb2014, author = {Wolf, Martin and Biesen, Ina van der and Greeb, Birgit}, title = {Mein Freund, die Uni}, series = {Die neue Hochschule : DNH : f{\"u}r anwendungsbezogene Wissenschaft und Kunst}, volume = {2014}, journal = {Die neue Hochschule : DNH : f{\"u}r anwendungsbezogene Wissenschaft und Kunst}, number = {2}, publisher = {HLB}, address = {Bonn}, issn = {0340-448X}, pages = {54 -- 56}, year = {2014}, language = {de} } @inproceedings{KallweitFerreinScholletal.2014, author = {Kallweit, Stephan and Ferrein, Alexander and Scholl, Ingrid and Reichert, Walter}, title = {Mobile Autonome Systeme in der Lehre, am Beispiel der ROS Summer School}, series = {Tagungsband AALE 2014 : das Forum f{\"u}r Fachleute der Automatisierungstechnik aus Hochschulen und Wirtschaft ; 11. Fachkonferenz, Regensburg ; [11. Konferenz f{\"u}r Angewandte Automatisierungstechnik in Lehre und Entwicklung / Ostbayerische Technische Hochschule Regensburg; VFAALE, Verein der Freunde und F{\"o}rderer der Angewandten Automatisierungstechnik]}, booktitle = {Tagungsband AALE 2014 : das Forum f{\"u}r Fachleute der Automatisierungstechnik aus Hochschulen und Wirtschaft ; 11. Fachkonferenz, Regensburg ; [11. Konferenz f{\"u}r Angewandte Automatisierungstechnik in Lehre und Entwicklung / Ostbayerische Technische Hochschule Regensburg; VFAALE, Verein der Freunde und F{\"o}rderer der Angewandten Automatisierungstechnik]}, publisher = {Dt. Industrieverl.}, address = {M{\"u}nchen}, isbn = {978-3-8356-7142-3}, pages = {157 -- 163}, year = {2014}, language = {de} } @article{TakenagaBiselliSchnitzleretal.2014, author = {Takenaga, Shoko and Biselli, Manfred and Schnitzler, Thomas and {\"O}hlschl{\"a}ger, Peter and Wagner, Torsten and Sch{\"o}ning, Michael Josef}, title = {Toward multi-analyte bioarray sensors: LAPS-based on-chip determination of a Michaelis-Menten-like kinetics for cell culturing}, series = {Physica status solidi A : Applications and materials science}, volume = {211}, journal = {Physica status solidi A : Applications and materials science}, number = {6}, publisher = {Wiley-VCH}, address = {Weinheim}, issn = {1521-396X (E); 1862-6319 (E-Journal); 0031-8965 (Print); 1862-6300 (Print)}, doi = {10.1002/pssa.201330464}, pages = {1410 -- 1415}, year = {2014}, abstract = {The metabolic activity of Chinese hamster ovary (CHO) cells was observed using a light-addressable potentiometric sensor (LAPS). The dependency toward different glucose concentrations (17-200 mM) follows a Michaelis-Menten kinetics trajectory with Kₘ = 32.8 mM, and the obtained Kₘ value in this experiment was compared with that found in literature. In addition, the pH shift induced by glucose metabolism of tumor cells transfected with the HPV-16 genome (C3 cells) was successfully observed. These results indicate the possibility to determine the tumor cells metabolism with a LAPS-based measurement device.}, language = {en} } @incollection{Schmidt2014, author = {Schmidt, Herbert}, title = {Angst vor Zukunft, Lust auf Zukunft}, series = {Re|peat-Jahrbuch Treasury und Private Banking : Produkte, M{\"a}rkte und Strategien zum Nachschlagen und Verstehen}, booktitle = {Re|peat-Jahrbuch Treasury und Private Banking : Produkte, M{\"a}rkte und Strategien zum Nachschlagen und Verstehen}, publisher = {Roland Eller}, address = {Potsdam}, pages = {255 -- 269}, year = {2014}, language = {de} } @article{WuBronderPoghossianetal.2014, author = {Wu, Chunsheng and Bronder, Thomas and Poghossian, Arshak and Werner, Frederik and B{\"a}cker, Matthias and Sch{\"o}ning, Michael Josef}, title = {Label-free electrical detection of DNA with a multi-spot LAPS: First step towards light-addressable DNA chips}, series = {Physica status solidi A : Applications and materials science}, volume = {211}, journal = {Physica status solidi A : Applications and materials science}, number = {6}, publisher = {Wiley-VCH}, address = {Weinheim}, issn = {1521-396X (E-Journal); 1862-6319 (E-Journal); 0031-8965 (Print); 1862-6300 (Print)}, doi = {10.1002/pssa.201330442}, pages = {1423 -- 1428}, year = {2014}, abstract = {A multi-spot (4 × 4 spots) light-addressable potentiometric sensor (MLAPS) consisting of an Al-p-Si-SiO2 structure has been applied for the label-free electrical detection of DNA (deoxyribonucleic acid) immobilization and hybridization by the intrinsic molecular charge for the first time. Single-stranded probe ssDNA molecules (20 bases) were covalently immobilized onto the silanized SiO2 gate surface. The unspecific adsorption of mismatch ssDNA on the MLAPS gate surface was blocked by bovine serum albumin molecules. To reduce the screening effect and to achieve a high sensor signal, the measurements were performed in a low ionic-strength solution. The photocurrent-voltage (I-V) curves were simultaneously recorded on all 16 spots after each surface functionalization step. Large shifts of I-V curves of 25 mV were registered after the DNA immobilization and hybridization event. In contrast, a small potential shift (∼5 mV) was observed in case of mismatch ssDNA, revealing good specificity of the sensor. The obtained results demonstrate the potential of the MLAPS as promising transducer platform for the multi-spot label-free electrical detection of DNA molecules by their intrinsic molecular charge.}, language = {en} } @article{PhamStaat2014, author = {Pham, Phu Tinh and Staat, Manfred}, title = {FEM-based shakedown analysis of hardening structures}, series = {Asia Pacific journal on computational engineering}, journal = {Asia Pacific journal on computational engineering}, number = {1}, publisher = {SpringerOpen}, address = {Berlin}, issn = {2196-1166 (E-Journal)}, doi = {10.1186/2196-1166-1-4}, pages = {Article No. 4}, year = {2014}, abstract = {This paper develops a new finite element method (FEM)-based upper bound algorithm for limit and shakedown analysis of hardening structures by a direct plasticity method. The hardening model is a simple two-surface model of plasticity with a fixed bounding surface. The initial yield surface can translate inside the bounding surface, and it is bounded by one of the two equivalent conditions: (1) it always stays inside the bounding surface or (2) its centre cannot move outside the back-stress surface. The algorithm gives an effective tool to analyze the problems with a very high number of degree of freedom. Our numerical results are very close to the analytical solutions and numerical solutions in literature.}, language = {en} } @article{Laack2014, author = {Laack, Walter van}, title = {Therefore Fermat is right}, series = {American journal of humanities and social sciences : AJHSS}, volume = {2}, journal = {American journal of humanities and social sciences : AJHSS}, number = {2}, issn = {2329-079X (E-Journal); 2329-0781 (Print)}, pages = {117 -- 120}, year = {2014}, abstract = {It was Fernat's idea to investigate how many numbers would fulfill the equation according to the Pythagorean Theorem if the exponent were increased to random, e.g. to a3 + b3 = c3. His question became therefore: are there two whole numbers the cubes of which add up to the volume of the cube of a third whole number? He posed this same question, of course, for all kinds of higher exponents, so that the equation could be generalized: is there an integral solution for the equation an + bn = cn, if the exponent n is higher than 2? Although in 1993, the English mathematician Andrew Wiles was able to produce an arithmetical proof for Fermat's famous theorem, I will show that there is a simple logical explanation which is also pragmatic and plausible and what is the result of a fundamental alternative idea how our world seems to be constructed.}, language = {en} } @article{AlebouyehSamamiPieperBreitbachetal.2014, author = {Alebouyeh Samami, Behzad and Pieper, Martin and Breitbach, Gerd and Hodapp, Josef}, title = {Heat production in the windings of the stators of electric machines under stationary condition}, series = {Heat and mass transfer}, volume = {50}, journal = {Heat and mass transfer}, publisher = {Springer}, address = {Heidelberg}, issn = {0947-7411 (Print) ; 1432-1181 (E-Journal)}, doi = {10.1007/s00231-014-1371-8}, pages = {1707 -- 1716}, year = {2014}, abstract = {In electric machines due to high currents and resistive losses (joule heating) heat is produced. To avoid damages by overheating the design of effective cooling systems is required. Therefore the knowledge of heat sources and heat transfer processes is necessary. The purpose of this paper is to illustrate a good and effective calculation method for the temperature analysis based on homogenization techniques. These methods have been applied for the stator windings in a slot of an electric machine consisting of copper wires and resin. The key quantity here is an effective thermal conductivity, which characterizes the heterogeneous wire resin-arrangement inside the stator slot. To illustrate the applicability of the method, the analysis of a simplified, homogenized model is compared with the detailed analysis of temperature behavior inside a slot of an electric machine according to the heat generation. We considered here only the stationary situation. The achieved numerical results are accurate and show that the applied homogenization technique works in practice. Finally the results of simulations for the two cases, the original model of the slot and the homogenized model chosen for the slot (unit cell), are compared to experimental results.}, language = {en} } @article{GuoSekiMiyamotoetal.2014, author = {Guo, Yuanyuan and Seki, Kosuke and Miyamoto, Ko-ichiro and Wagner, Torsten and Sch{\"o}ning, Michael Josef and Yoshinobu, Tatsuo}, title = {Novel photoexcitation method for light-addressable potentiometric sensor with higher spatial resolution}, series = {Applied physics express : APEX}, volume = {7}, journal = {Applied physics express : APEX}, number = {6}, publisher = {IOP}, address = {Bristol}, issn = {1882-0786 (E-Journa); 1882-0778 (Print)}, doi = {10.7567/APEX.7.067301}, pages = {067301-4}, year = {2014}, abstract = {A novel photoexcitation method for the light-addressable potentiometric sensor (LAPS) is proposed to achieve a higher spatial resolution of chemical images. The proposed method employs a combined light source that consists of a modulated light probe, which generates the alternating photocurrent signal, and a ring of constant illumination surrounding it. The constant illumination generates a sheath of carriers with increased concentration which suppresses the spread of photocarriers by enhanced recombination. A device simulation was carried out to verify the effect of constant illumination on the spatial resolution, which demonstrated that a higher spatial resolution can be obtained.}, language = {en} } @article{WhiteheadOehlschlaegerAlmajhdietal.2014, author = {Whitehead, Mark and {\"O}hlschl{\"a}ger, Peter and Almajhdi, Fahad N. and Alloza, Leonor and Marz{\´a}bal, Pablo and Meyers, Ann E. and Hitzeroth, Inga I. and Rybicki, Edward P.}, title = {Human papillomavirus (HPV) type 16 E7 protein bodies cause tumour regression in mice}, series = {BMC cancer}, journal = {BMC cancer}, number = {14:367}, publisher = {BioMed Central}, address = {London}, issn = {1471-2407}, doi = {10.1186/1471-2407-14-367}, pages = {1 -- 15}, year = {2014}, language = {en} } @incollection{PoghossianWeilandSchoening2014, author = {Poghossian, Arshak and Weiland, Maryam and Sch{\"o}ning, Michael Josef}, title = {Nanoplate field-effect capacitors: a new transducer structure for multiparameter (bio-)chemical sensing}, series = {Multisensor system for chemical analysis : materials and sensors}, booktitle = {Multisensor system for chemical analysis : materials and sensors}, editor = {Lvova, Larisa and Kirsanov, Dmitry and di Natale, Corrado and Legin, Audrey}, edition = {1}, publisher = {Jenny Stanford Publishing}, address = {Singapore}, isbn = {978-981-4411-15-8 ; 978-981-4411-16-5}, doi = {10.1201/b15491-11}, pages = {333 -- 373}, year = {2014}, abstract = {An array of electrically isolated nanoplate field-effect silicon-on-insulator (SOI) capacitors as a new transducer structure for multiparameter (bio-)chemical sensing is presented. The proposed approach allows addressable biasing and electrical readout of multiple nanoplate field-effect capacitive (bio-)chemical sensors on the same SOI chip, as well as differential-mode measurements. The realized sensor chip has been applied for pH and penicillin concentration measurements, electrical monitoring of polyelectrolyte multilayer formation, and the label-free electrical detection of consecutive deoxyribonucleic acid (DNA) hybridization and denaturation events.}, language = {en} } @article{Timme2014, author = {Timme, Michael}, title = {Wohnungseigent{\"u}mergemeinschaft - Einstimmigkeitserfordernis bei Errichtung einer Mobilfunkantenne}, series = {Monatsschrift f{\"u}r Deutsches Recht : MDR : Zeitschrift f{\"u}r die Zivilrechts-Praxis}, volume = {68 (2014)}, journal = {Monatsschrift f{\"u}r Deutsches Recht : MDR : Zeitschrift f{\"u}r die Zivilrechts-Praxis}, number = {11}, publisher = {Verlag Dr. Otto Schmidt}, address = {K{\"o}ln}, issn = {0340-1812}, pages = {634 -- 635}, year = {2014}, abstract = {Der BGH (BGH v. 25.1.2014 - V ZR 48/13, MDR 2014, 399) hatte dar{\"u}ber zu befinden, ob auf dem Dach eines Hauses, das im Eigentum einer Wohnungseigent{\"u}mergemeinschaft steht, auch gegen den Willen eines einzelnen Eigent{\"u}mers eine Mobilfunkantenne angebracht werden kann. Das Urteil f{\"u}hrt in das Spannungsfeld einer Abw{\"a}gung zwischen Mehrheits- und Individualinteressen innerhalb einer WEG. Insoweit betont der BGH den grunds{\"a}tzlichen Vorrang der Individualinteressen, jedenfalls soweit es um Beeintr{\"a}chtigungen geht, die verst{\"a}ndlicherweise von einem Eigent{\"u}mer abgelehnt werden k{\"o}nnen. Der BGH verlangt im Ergebnis im Zweifel eine allseitige Zustimmung. Das Urteil ist zu begr{\"u}ßen, l{\"a}sst aber f{\"u}r die Zukunft Abgrenzungsfragen offen.}, language = {de} } @article{WagnerDollSchoening2014, author = {Wagner, Patrick and Doll, Theodor and Sch{\"o}ning, Michael Josef}, title = {Engineering of functional interfaces / Patrick Wagner ; Theodor Doll ; Michael J. Sch{\"o}ning (eds.)}, series = {Physica status solidi (A) : Applications and materials science}, volume = {211}, journal = {Physica status solidi (A) : Applications and materials science}, number = {6}, publisher = {Wiley-VCH}, address = {Weinheim}, issn = {1521-396X (E-Book); 1862-6319 (E-Book); 0031-8965 (Print); 1862-6300 (Print)}, doi = {10.1002/pssa.201470241}, pages = {1339 -- 1339}, year = {2014}, language = {en} } @book{Huening2014, author = {H{\"u}ning, Felix}, title = {The fundamentals of electrical engineering for mechatronics}, publisher = {de Gruyter}, address = {Berlin}, isbn = {978-3-11-034991-7 (Druckausg.)}, pages = {IX, 208 S.}, year = {2014}, language = {en} } @article{FuestKotliarWalteretal.2014, author = {Fuest, Matthias and Kotliar, Konstantin and Walter, Peter and Plange, Niklas}, title = {Monitoring intraocular pressure changes after intravitreal Ranibizumab injection using rebound tonometry}, series = {Ophthalmic and physiological optics}, volume = {34}, journal = {Ophthalmic and physiological optics}, number = {4}, publisher = {Wiley-Blackwell}, address = {Oxford}, issn = {1475-1313 (E-Journal); 0275-5408 (Print)}, doi = {10.1111/opo.12134}, pages = {438 -- 444}, year = {2014}, language = {en} } @article{KueppersSteffenHellmuthetal.2014, author = {K{\"u}ppers, Tobias and Steffen, Victoria and Hellmuth, Hendrik and O'Connell, Timothy and Bongaerts, Johannes and Maurer, Karl-Heinz and Wiechert, Wolfgang}, title = {Developing a new production host from a blueprint: Bacillus pumilus as an industrial enzyme producer}, series = {Microbial cell factories}, volume = {13}, journal = {Microbial cell factories}, publisher = {BioMed Central}, address = {London}, issn = {1475-2859 (E-Journal)}, doi = {10.1186/1475-2859-13-46}, pages = {Article No. 46}, year = {2014}, language = {en} } @article{TuraliyevaYeshibaevDigeletal.2014, author = {Turaliyeva, M. and Yeshibaev, A. and Digel, Ilya and Elibayeva, G. and Sydykova, A. and Uspabayeva, A. and Dosybayeva, G. and Zhylysbayeva, A. and Lakhanova, K.}, title = {Molecular-genetic identification of emerged novel invasive pathogens of Asiatic Elm Ulmus pumila L}, series = {Life science journal}, volume = {11}, journal = {Life science journal}, number = {Spec. iss. 5s}, publisher = {Marsland Press}, address = {New York}, issn = {1097-8135}, doi = {10.7537/marslsj1105s14.33}, pages = {171 -- 175}, year = {2014}, abstract = {The dwarf elm Ulmus pumila L. (Ulmaceae) is one of indigenous species of flora in Kazakhstan and forms a basis of dendroflora in virtually all settlements of the region. In the past decade, multiple outbreaks of previously unknown diseases of the small-leaved elm have been registered. In our study, by the molecular-genetic analysis it was found that the pathogens responsible for the outbreaks are microfungi belonging to the genus Fusarium - F. solani and F. oxysporum. The nucleotide sequences (ITS regions) isolated from the diseased trees showed very high similarity with the GenBank control numbers EU625403.1 and FJ478128.1 (100.0 and 99.0 \% respectively). Oncoming research will focus on the search of natural microbial antagonists of the discovered phytopathogens.}, language = {en} } @article{GuoMiyamotoWagneretal.2014, author = {Guo, Yuanyuan and Miyamoto, Ko-ichiro and Wagner, Torsten and Sch{\"o}ning, Michael Josef and Yoshinobu, Tatsuo}, title = {Theoretical study and simulation of light-addressable potentiometric sensors}, series = {Physica status solidi (A) : applications and materials}, volume = {211}, journal = {Physica status solidi (A) : applications and materials}, number = {6}, publisher = {Wiley-VCH}, address = {Weinheim}, issn = {0031-8965}, doi = {10.1002/pssa.201330354}, pages = {1467 -- 1472}, year = {2014}, abstract = {The light-addressable potentiometric sensor (LAPS) is a semiconductor-based potentiometric sensor using a light probe with an ability of detecting the concentration of biochemical species in a spatially resolved manner. As an important biomedical sensor, research has been conducted to improve its performance, for instance, to realize high-speed measurement. In this work, the idea of facilitating the device-level simulation, instead of using an equivalent-circuit model, is presented for detailed analysis and optimization of the performance of the LAPS. Both carrier distribution and photocurrent response have been simulated to provide new insight into both amplitude-mode and phase-mode operations of the LAPS. Various device parameters can be examined to effectively design and optimize the LAPS structures and setups for enhanced performance.}, language = {en} } @incollection{Laack2014, author = {Laack, Walter van}, title = {Gefahren heutiger neurologischer Schlussfolgerungen f{\"u}r ethische Verantwortung}, series = {Ethik und Moral in Staat, Wirtschaft und Gesellschaft : 5. Rotary-Tag, 14.-15.2.2014, Kleve}, booktitle = {Ethik und Moral in Staat, Wirtschaft und Gesellschaft : 5. Rotary-Tag, 14.-15.2.2014, Kleve}, publisher = {Edition Virgines}, address = {Lingen}, organization = {Rotary-Tag <5, 2014, Kleve>}, isbn = {978-3-944011-21-9}, pages = {98 -- 114}, year = {2014}, language = {de} } @incollection{Laack2014, author = {Laack, Walter van}, title = {Zu neuen wissenschaftlichen Erkenntnissen zur Vereinbarkeit von Vernunft und Glaube}, series = {Ethik und Moral in Staat, Wirtschaft und Gesellschaft : 5. Rotary-Tag, 14.-15.2.2014, Kleve}, booktitle = {Ethik und Moral in Staat, Wirtschaft und Gesellschaft : 5. Rotary-Tag, 14.-15.2.2014, Kleve}, publisher = {Edition Virgines}, address = {Lingen}, organization = {Rotary-Tag <5, 2014, Kleve>}, isbn = {978-3-944011-21-9}, pages = {152 -- 162}, year = {2014}, language = {de} } @book{Siedenbiedel2014, author = {Siedenbiedel, Georg}, title = {Corporate Compliance : Grundelemente der strukturellen Integration von Compliance-Konzepten}, publisher = {NWB-Verl.}, address = {Herne}, isbn = {3-482-65131-0}, pages = {292 S.}, year = {2014}, language = {de} } @book{NebgenPeterson2014, author = {Nebgen, Nikolaus and Peterson, Leif Arne}, title = {Holzbau kompakt nach Eurocode 5}, edition = {4. Aufl.}, publisher = {Beuth}, address = {Berlin}, isbn = {978-3-410-22414-3}, pages = {XII, 267 S. : Ill., graph. Darst.}, year = {2014}, language = {de} } @phdthesis{Werner2014, author = {Werner, Frederik}, title = {Development of light-addressable potentiometric sensor systems and their applications in biotechnological environments}, pages = {XI, 149 S.}, year = {2014}, language = {en} } @inproceedings{SchreiberBarkschatKraft2014, author = {Schreiber, Marc and Barkschat, Kai and Kraft, Bodo}, title = {Using Continuous Integration to organize and monitor the annotation process of domain specific corpora}, series = {5th International Conference on Information and Communication Systems (ICICS) : 1-3 April 2014, Irbid, Jordanien}, booktitle = {5th International Conference on Information and Communication Systems (ICICS) : 1-3 April 2014, Irbid, Jordanien}, organization = {International Conference on Information and Communication Systems <5, 2014, Irbid, Jordanien>}, isbn = {978-1-4799-3022-7}, doi = {10.1109/IACS.2014.6841958}, pages = {1 -- 6}, year = {2014}, language = {en} } @article{RiedelKartchemnikSchoeningetal.2014, author = {Riedel, Marc and Kartchemnik, Julia and Sch{\"o}ning, Michael Josef and Lisdat, Fred}, title = {Impedimetric DNA detection - steps forward to sensorial application}, series = {Analytical chemistry}, volume = {86 (2014)}, journal = {Analytical chemistry}, number = {15}, publisher = {ACS Publications}, address = {Columbus}, issn = {1520-6882 (E-Journal); 0003-2700 (Print); 0096-4484 (Print)}, doi = {10.1021/ac501800q}, pages = {7867 -- 7874}, year = {2014}, abstract = {This study describes a label-free impedimetric sensor based on short ssDNA recognition elements for the detection of hybridization events. We concentrate on the elucidation of the influence of target length and recognition sequence position on the sensorial performance. The impedimetric measurements are performed in the presence of the redox system ferri-/ferrocyanide and show an increase in charge transfer resistance upon hybridization of ssDNA to the sensor surface. Investigations on the impedimetric signal stability demonstrate a clear influence of the buffers used during the sensor preparation and the choice of the passivating mercaptoalcanol compound. A stable sensor system has been developed, enabling a reproducible detection of 25mer target DNA in the low nanomolar range. After hybridization, a sensor regeneration can be reached with deionized water by adjustment of effective convection conditions, ensuring a sensor reusability. By investigations of longer targets with overhangs exposed to the solution, we can demonstrate applicability of the impedimetric detection for longer ssDNA. However, a decreasing charge transfer resistance change (ΔRct) is found by extending the overhang. As a strategy to increase the impedance change for longer target strands, the position of the recognition sequence can be designed in a way that a small overhang is exposed to the electrode surface. This is found to result in an increase in the relative Rct change. These results suggest that DNA and consequently negative charge near the electrode possess a larger impact on the impedimetric signal than DNA further away.}, language = {en} } @masterthesis{Kobus2014, type = {Bachelor Thesis}, author = {Kobus, Timm}, title = {Untersuchung des unterschiedlichen Reduktionsverhaltens von unterschiedlich para-substituierten Acetophenonen mit Chiralidon R \& S}, school = {Fachhochschule Aachen}, pages = {128 S.}, year = {2014}, language = {de} } @masterthesis{Maintz2014, type = {Bachelor Thesis}, author = {Maintz, Stephan}, title = {Enantioselektive Reduktion prochiraler Carbonylverbindungen mit Chiralidon R \& S in einem kontinuierlich betriebenen Festbettreaktor}, school = {Fachhochschule Aachen}, pages = {86 S.}, year = {2014}, language = {de} } @inproceedings{NiedermeierClemensKowalskietal.2014, author = {Niedermeier, H. and Clemens, J. and Kowalski, Julia and Macht, S. and Heinen, D. and Hoffmann, R. and Linder, Peter}, title = {Navigation system for a research ice probe for antarctic glaciers}, series = {IEEE/ION Position, Location and Navigation Symposium (PLANS) ; 5-8 May 2014, Monterey, Calif.}, booktitle = {IEEE/ION Position, Location and Navigation Symposium (PLANS) ; 5-8 May 2014, Monterey, Calif.}, publisher = {IEEE}, address = {Piscataway, NJ}, organization = {Position, Location and Navigation Symposium <2014, Monterey, Calif.>}, isbn = {978-1-4799-3319-8}, pages = {959 -- 975}, year = {2014}, language = {en} } @article{GebhardtFateri2014, author = {Gebhardt, Andreas and Fateri, Miranda}, title = {3D-Drucken und die Anwendungen}, series = {RTejournal - Forum f{\"u}r Rapid Technologie}, volume = {11 (2014)}, journal = {RTejournal - Forum f{\"u}r Rapid Technologie}, number = {1}, issn = {1614-0923}, pages = {1 -- 9}, year = {2014}, language = {de} } @article{GuoMiyamotoWagneretal.2014, author = {Guo, Yuanyuan and Miyamoto, Ko-ichiro and Wagner, Torsten and Sch{\"o}ning, Michael Josef and Yoshinobu, Tatsuo}, title = {Device simulation of the light-addressable potentiometric sensor for the investigation of the spatial resolution}, series = {Sensors and actuators B: Chemical}, volume = {204}, journal = {Sensors and actuators B: Chemical}, publisher = {Elsevier}, address = {Amsterdam}, issn = {1873-3077 (E-Journal); 0925-4005 (Print)}, doi = {10.1016/j.snb.2014.08.016}, pages = {659 -- 665}, year = {2014}, abstract = {As a semiconductor-based electrochemical sensor, the light-addressable potentiometric sensor (LAPS) can realize two dimensional visualization of (bio-)chemical reactions at the sensor surface addressed by localized illumination. Thanks to this imaging capability, various applications in biochemical and biomedical fields are expected, for which the spatial resolution is critically significant. In this study, therefore, the spatial resolution of the LAPS was investigated in detail based on the device simulation. By calculating the spatiotemporal change of the distributions of electrons and holes inside the semiconductor layer in response to a modulated illumination, the photocurrent response as well as the spatial resolution was obtained as a function of various parameters such as the thickness of the Si substrate, the doping concentration, the wavelength and the intensity of illumination. The simulation results verified that both thinning the semiconductor substrate and increasing the doping concentration could improve the spatial resolution, which were in good agreement with known experimental results and theoretical analysis. More importantly, new findings of interests were also obtained. As for the dependence on the wavelength of illumination, it was found that the known dependence was not always the case. When the Si substrate was thick, a longer wavelength resulted in a higher spatial resolution which was known by experiments. When the Si substrate was thin, however, a longer wavelength of light resulted in a lower spatial resolution. This finding was explained as an effect of raised concentration of carriers, which reduced the thickness of the space charge region. The device simulation was found to be helpful to understand the relationship between the spatial resolution and device parameters, to understand the physics behind it, and to optimize the device structure and measurement conditions for realizing higher performance of chemical imaging systems.}, language = {en} } @incollection{NiemuellerEwertReuteretal.2014, author = {Niem{\"u}ller, Tim and Ewert, Daniel and Reuter, Sebastian and Ferrein, Alexander and Jeschke, Sabina and Lakemeyer, Gerhard}, title = {RoboCup logistics league sponsored by festo: A competitive factory automation testbed}, series = {RoboCup 2013: Robot World Cup XVII : Eindhoven; Netherlands; 1 July 2013 through 1 July 2013. (Lecture notes in computer science ; 8371)}, booktitle = {RoboCup 2013: Robot World Cup XVII : Eindhoven; Netherlands; 1 July 2013 through 1 July 2013. (Lecture notes in computer science ; 8371)}, publisher = {Springer}, address = {Berlin}, organization = {RoboCup International Symposium <17, 2013, Eindhoven>}, isbn = {978-3-662-44467-2 (Print) 978-3-662-44468-9 (Online)}, pages = {336 -- 347}, year = {2014}, abstract = {A new trend in automation is to deploy so-called cyber-physical systems (CPS) which combine computation with physical processes. The novel RoboCup Logistics League Sponsored by Festo (LLSF) aims at such CPS logistic scenarios in an automation setting. A team of robots has to produce products from a number of semi-finished products which they have to machine during the game. Different production plans are possible and the robots need to recycle scrap byproducts. This way, the LLSF is a very interesting league offering a number of challenging research questions for planning, coordination, or communication in an application-driven scenario. In this paper, we outline the objectives of the LLSF and present steps for developing the league further towards a benchmark for logistics scenarios for CPS. As a major milestone we present the new automated referee system which helps in governing the game play as well as keeping track of the scored points in a very complex factory scenario.}, language = {en} } @article{KhaydukovaZadorozhnayaKirsanovetal.2014, author = {Khaydukova, M. M. and Zadorozhnaya, O. A. and Kirsanov, D. O. and Iken, Heiko and Rolka, David and Sch{\"o}ning, Michael Josef and Babain, V. A. and Vlasov, Yu. G. and Legin, A. V.}, title = {Multivariate processing of atomic-force microscopy images for detection of the response of plasticized polymeric membranes}, series = {Russian journal of applied chemistry}, volume = {87}, journal = {Russian journal of applied chemistry}, number = {3}, publisher = {Springer}, address = {Dordrecht}, issn = {1608-3296 (E-Journal); 1070-4272 (Print)}, doi = {10.1134/S1070427214030112}, pages = {307 -- 314}, year = {2014}, abstract = {The possibility of using the atomic-force microscopy as a method for detection of the analytical signal from plasticized polymeric sensor membranes was analyzed. The surfaces of cadmium-selective membranes based on two polymeric matrices were examined. The digital images were processed with multivariate image analysis techniques. A correlation was found between the surface profile of an ion-selective membrane and the concentration of the ion in solution.}, language = {en} } @article{HoltrupSadeghfamHeuermannetal.2014, author = {Holtrup, S. and Sadeghfam, Arash and Heuermann, Holger and Awakowicz, P.}, title = {Characterization and optimization technique for microwave-driven high-intensity discharge lamps using hot S-parameters}, series = {IEEE transactions on microwave theories and techniques}, volume = {62}, journal = {IEEE transactions on microwave theories and techniques}, number = {10}, publisher = {IEEE}, address = {New York}, issn = {0018-9480}, doi = {10.1109/TMTT.2014.2342652}, pages = {2471 -- 2480}, year = {2014}, abstract = {High-intensity discharge lamps can be driven by radio-frequency signals in the ISM frequency band at 2.45 GHz, using a matching network to transform the impedance of the plasma to the source impedance. To achieve an optimal operating condition, a good characterization of the lamp in terms of radio frequency equivalent circuits under operating conditions is necessary, enabling the design of an efficient matching network. This paper presents the characterization technique for such lamps and presents the design of the required matching network. For the characterization, a high-intensity discharge lamp was driven by a monofrequent large signal at 2.45 GHz, whereas a frequency sweep over 300 MHz was performed across this signal to measure so-called small-signal hot S-parameters using a vector network analyzer. These parameters are then used as an equivalent load in a circuit simulator to design an appropriate matching network. Using the measured data as a black-box model in the simulation results in a quick and efficient method to simulate and design efficient matching networks in spite of the complex plasma behavior. Furthermore, photometric analysis of high-intensity discharge lamps are carried out, comparing microwave operation to conventional operation.}, language = {en} } @article{StadlerGarveyEmbsetal.2014, author = {Stadler, Alexander Maximilian and Garvey, Christopher J. and Embs, Jan Peter and Koza, Michael Marek and Unruh, Tobias and Artmann, Gerhard and Zaccai, Guiseppe}, title = {Picosecond dynamics in haemoglobin from different species: A quasielastic neutron scattering study}, series = {Biochimica et biophysica acta (BBA): General Subjects}, volume = {1840}, journal = {Biochimica et biophysica acta (BBA): General Subjects}, number = {10}, publisher = {Elsevier}, address = {Amsterdam}, issn = {1872-8006 (E-Journal); 0304-4165 (Print)}, doi = {10.1016/j.bbagen.2014.06.007}, pages = {2989 -- 2999}, year = {2014}, language = {en} } @inproceedings{BuniatyanHuckPoghossianetal.2014, author = {Buniatyan, V. V. and Huck, Christina and Poghossian, Arshak and Sch{\"o}ning, Michael Josef and Rustamyan, L. G. and Hovnikyan, H. H.}, title = {Equivalent circuit and optimization of impedance characteristics of an electrolyte conductivity sensor}, series = {Proceedings of State Engineering University Armenia : Series Information technologies, electronics, radio engineering}, volume = {Iss. 17}, booktitle = {Proceedings of State Engineering University Armenia : Series Information technologies, electronics, radio engineering}, number = {No. 1}, pages = {69 -- 76}, year = {2014}, language = {en} } @article{GebhardtHoetterZiebura2014, author = {Gebhardt, Andreas and H{\"o}tter, Jan-Steffen and Ziebura, Dawid}, title = {Impact of SLM build parameters on the surface quality}, series = {RTejournal - Forum f{\"u}r Rapid Technologien}, volume = {11 (2014)}, journal = {RTejournal - Forum f{\"u}r Rapid Technologien}, number = {1}, issn = {1614-0923}, pages = {1 -- 14}, year = {2014}, language = {de} } @masterthesis{Huber2014, type = {Bachelor Thesis}, author = {Huber, Eugen}, title = {Selektive Reduktion von bifunktionellen aromatischen Carbonylverbindungen}, publisher = {FH Aachen}, address = {Aachen}, school = {Fachhochschule Aachen}, pages = {67 S.}, year = {2014}, language = {de} } @incollection{Reichert2014, author = {Reichert, Walter}, title = {Der Vertriebsingenieur: Ausbildung und Beruf}, series = {Berufsstart Technik : das Karriereportal f{\"u}r junge Akademiker ; Ingenieure, Naturwissenschaftler, Informatiker}, booktitle = {Berufsstart Technik : das Karriereportal f{\"u}r junge Akademiker ; Ingenieure, Naturwissenschaftler, Informatiker}, publisher = {Resch}, address = {Großenkneten}, pages = {456 -- 458}, year = {2014}, language = {de} } @article{FrotscherStaat2014, author = {Frotscher, Ralf and Staat, Manfred}, title = {Stresses produced by different textile mesh implants in a tissue equivalent}, series = {BioNanoMaterials}, volume = {15}, journal = {BioNanoMaterials}, number = {1-2}, publisher = {De Gruyter}, address = {Berlin}, issn = {2191-4672 (E-Journal); 2193-066X (E-Journal); 0011-8656 (Print); 1616-0177 (Print); 2193-0651 (Print)}, doi = {10.1515/bnm-2014-0003}, pages = {25 -- 30}, year = {2014}, abstract = {Two single-incision mini-slings used for treating urinary incontinence in women are compared with respect to the stresses they produce in their surrounding tissue. In an earlier paper we experimentally observed that these implants produce considerably different stress distributions in a muscle tissue equivalent. Here we perform 2D finite element analyses to compare the shear stresses and normal stresses in the tissue equivalent for the two meshes and to investigate their failure behavior. The results clearly show that the Gynecare TVT fails for increasing loads in a zipper-like manner because it gradually debonds from the surrounding tissue. Contrary to that, the tissue at the ends of the DynaMesh-SIS direct may rupture but only at higher loads. The simulation results are in good agreement with the experimental observations thus the computational model helps to interpret the experimental results and provides a tool for qualitative evaluation of mesh implants.}, language = {en} } @article{AlhwarinFerreinScholl2014, author = {Alhwarin, Faraj and Ferrein, Alexander and Scholl, Ingrid}, title = {IR stereo kinect: improving depth images by combining structured light with IR stereo}, pages = {1 -- 9}, year = {2014}, language = {en} } @book{Hoever2014, author = {Hoever, Georg}, title = {Vorkurs Mathematik : Theorie und Aufgaben mit vollst{\"a}ndig durchgerechneten L{\"o}sungen. - (Springer-Lehrbuch)}, publisher = {Springer Spektrum}, address = {Berlin [u.a.]}, isbn = {978-3-642-54870-3 (Druckausg.)}, pages = {X, 292 S. : graph. Darst.}, year = {2014}, language = {de} } @article{FiedlerHennMelcher2014, author = {Fiedler, Gerda and Henn, Gudrun and Melcher, Karin}, title = {ANPAK - ein semesterbegleitender Anpassungskurs}, series = {Zeitschrift f{\"u}r Hochschulentwicklung}, volume = {9}, journal = {Zeitschrift f{\"u}r Hochschulentwicklung}, number = {4}, publisher = {{\"O}GHD}, address = {Wien}, issn = {2219-6994}, pages = {85 -- 100}, year = {2014}, abstract = {In Folge mehrj{\"a}hriger statistischer Untersuchungen an der FH Aachen ist unter anderem ein Eingangstest entstanden, der als Diagnosetool f{\"u}r einen erfolgreichen Studieneinstieg verwendet wird. Es hat sich herausgestellt, dass ein Testergebnis von weniger als 25 (von maximal 56 erreichbaren) Punkten die Chance auf einen erfolgreichen Studieneinstieg deutlich verringert. Ungef{\"a}hr die H{\"a}lfte aller Erstsemester hat weniger als 25 Punkte im Eingangstest. Weniger als 20 \% dieser Gruppe bestehen innerhalb eines Jahres die Klausur Mathematik 1. Die investierte Zeit von zwei Semestern ist mit Blick auf den Wissenszuwachs und damit letztendlich den Studienerfolg nicht effizient genutzt. Deshalb haben wir im WS 2013/14 einen semesterbegleitenden Anpassungskurs f{\"u}r diese Gruppe installiert. Ziel eines solchen Kurses ist es, die Student/innen innerhalb eines Jahres in die Lage zu versetzen, nach zwei Semestern problemlos den Vorlesungen in Mathematik zu folgen. Dieser Artikel beschreibt das Konzept dieses Anpassungskurses und zeigt erste Ergebnisse und Probleme des Pilotdurchgangs auf.}, language = {de} } @incollection{KirchnerReisertSchoening2014, author = {Kirchner, Patrick and Reisert, Steffen and Sch{\"o}ning, Michael Josef}, title = {Calorimetric gas sensors for hydrogen peroxide monitoring in aseptic food processes}, series = {Gas sensing fundamentals. (Springer Series on Chemical Sensors and Biosensors ; 15)}, booktitle = {Gas sensing fundamentals. (Springer Series on Chemical Sensors and Biosensors ; 15)}, publisher = {Springer}, address = {Heidelberg}, isbn = {978-3-642-54518-4 (Print) ; 978-3-642-54519-1 (Online)}, doi = {10.1007/5346_2013_51}, pages = {279 -- 309}, year = {2014}, abstract = {For the sterilisation of aseptic food packages it is taken advantage of the microbicidal properties of hydrogen peroxide (H2O2). Especially, when applied in vapour phase, it has shown high potential of microbial inactivation. In addition, it offers a high environmental compatibility compared to other chemical sterilisation agents, as it decomposes into oxygen and water, respectively. Due to a lack in sensory detection possibilities, a continuous monitoring of the H2O2 concentration was recently not available. Instead, the sterilisation efficacy is validated using microbiological tests. However, progresses in the development of calorimetric gas sensors during the last 7 years have made it possible to monitor the H2O2 concentration during operation. This chapter deals with the fundamentals of calorimetric gas sensing with special focus on the detection of gaseous hydrogen peroxide. A sensor principle based on a calorimetric differential set-up is described. Special emphasis is given to the sensor design with respect to the operational requirements under field conditions. The state-of-the-art regarding a sensor set-up for the on-line monitoring and secondly, a miniaturised sensor for in-line monitoring are summarised. Furthermore, alternative detection methods and a novel multi-sensor system for the characterisation of aseptic sterilisation processes are described.}, language = {en} } @incollection{SchoeningPoghossianGluecketal.2014, author = {Sch{\"o}ning, Michael Josef and Poghossian, Arshak and Gl{\"u}ck, Olaf and Thust, Marion}, title = {Electrochemical methods for the determination of chemical variables in aqueous media}, series = {Measurement, instrumentation, and sensors handbook / ed. by John G. Webster [u.a.] Vol. 2 : Electromagnetic, optical, radiation, chemical, and biomedical measurement}, booktitle = {Measurement, instrumentation, and sensors handbook / ed. by John G. Webster [u.a.] Vol. 2 : Electromagnetic, optical, radiation, chemical, and biomedical measurement}, publisher = {CRC Pr.}, address = {Boca Raton, Fla.}, isbn = {978-1-4398-4891-3}, pages = {55-1 -- 55-54}, year = {2014}, language = {en} } @article{BaeckerSchusserPoghossianetal.2014, author = {B{\"a}cker, Matthias and Schusser, Sebastian and Poghossian, Arshak and Sch{\"o}ning, Michael Josef}, title = {Multi-Parametererfassung mit siliziumbasiertem Sensorchip: Aus Drei mach Eins}, series = {GIT Labor-Fachzeitschrift}, journal = {GIT Labor-Fachzeitschrift}, number = {2}, publisher = {Wiley}, issn = {0016-3538}, pages = {28 -- 30}, year = {2014}, language = {de} } @inproceedings{HuckPoghossianBuniatyanetal.2014, author = {Huck, Christina and Poghossian, Arshak and Buniatyan, V. and Sch{\"o}ning, Michael Josef}, title = {Multi-parameter detection for supporting monitoring and control of biogas processes in agriculture}, series = {Sensoren und Messsysteme 2014 ; Beitr{\"a}ge der 17. GMA/ITG-Fachtagung vom 3. bis 4. Juni 2014 in N{\"u}rnberg. (ITG-Fachbericht ; 250)}, booktitle = {Sensoren und Messsysteme 2014 ; Beitr{\"a}ge der 17. GMA/ITG-Fachtagung vom 3. bis 4. Juni 2014 in N{\"u}rnberg. (ITG-Fachbericht ; 250)}, publisher = {VDE-Verl.}, address = {Berlin}, organization = {VDI/VDE-Gesellschaft Mess- und Automatisierungstechnik}, isbn = {978-3-8007-3622-5}, pages = {1 -- 5}, year = {2014}, language = {en} } @inproceedings{WernerYoshinobuMiyamotoetal.2014, author = {Werner, Frederik and Yoshinobu, T. and Miyamoto, K. and Sch{\"o}ning, Michael Josef and Wagner, Torsten}, title = {Semiconductor-based sensors for imaging of chemical processes}, series = {Sensoren und Messsysteme 2014 ; Beitr{\"a}ge der 17. GMA/ITG-Fachtagung vom 3. bis 4. Juni 2014 in N{\"u}rnberg. (ITG-Fachbericht ; 250)}, booktitle = {Sensoren und Messsysteme 2014 ; Beitr{\"a}ge der 17. GMA/ITG-Fachtagung vom 3. bis 4. Juni 2014 in N{\"u}rnberg. (ITG-Fachbericht ; 250)}, publisher = {VDE-Verl.}, address = {D{\"u}sseldorf}, organization = {VDI/VDE-Gesellschaft Mess- und Automatisierungstechnik}, isbn = {978-3-8007-3622-5}, pages = {1 -- 5}, year = {2014}, language = {en} } @inproceedings{WuBronderPoghossianetal.2014, author = {Wu, Chunsheng and Bronder, Thomas and Poghossian, Arshak and Sch{\"o}ning, Michael Josef}, title = {DNA-hybridization detection using light-addressable potentiometric sensor modified with gold layer}, series = {Sensoren und Messsysteme 2014 ; Beitr{\"a}ge der 17. GMA/ITG-Fachtagung vom 3. bis 4. Juni 2014 in N{\"u}rnberg. (ITG-Fachbericht ; 250)}, booktitle = {Sensoren und Messsysteme 2014 ; Beitr{\"a}ge der 17. GMA/ITG-Fachtagung vom 3. bis 4. Juni 2014 in N{\"u}rnberg. (ITG-Fachbericht ; 250)}, publisher = {VDE-Verl.}, address = {D{\"u}sseldorf}, organization = {VDI/VDE-Gesellschaft Mess- und Automatisierungstechnik}, isbn = {978-3-8007-3622-5}, pages = {1 -- 4}, year = {2014}, language = {en} } @inproceedings{OberlaenderKirchnerKeusgenetal.2014, author = {Oberl{\"a}nder, Jan and Kirchner, Patrick and Keusgen, M. and Sch{\"o}ning, Michael Josef}, title = {Flexible polyimide-based calorimetric gas sensors for monitoring hy-drogen peroxide in sterilisation processes of aseptic filling machines}, series = {Sensoren und Messsysteme 2014 ; Beitr{\"a}ge der 17. GMA/ITG-Fachtagung vom 3. bis 4. Juni 2014 in N{\"u}rnberg. (ITG-Fachbericht ; 250)}, booktitle = {Sensoren und Messsysteme 2014 ; Beitr{\"a}ge der 17. GMA/ITG-Fachtagung vom 3. bis 4. Juni 2014 in N{\"u}rnberg. (ITG-Fachbericht ; 250)}, publisher = {VDE-Verl.}, address = {D{\"u}sseldorf}, organization = {VDI/VDE-Gesellschaft Mess- und Automatisierungstechnik}, isbn = {978-3-8007-3622-5}, pages = {1 -- 4}, year = {2014}, language = {en} } @inproceedings{BaeckerSchusserLeinhosetal.2014, author = {B{\"a}cker, Matthias and Schusser, Sebastian and Leinhos, Marcel and Poghossian, Arshak and Sch{\"o}ning, Michael Josef}, title = {Sensor system for the monitoring of degradation processes of biodegradable biopolymers}, series = {Sensoren und Messsysteme 2014 ; Beitr{\"a}ge der 17. GMA/ITG-Fachtagung vom 3. bis 4. Juni 2014 in N{\"u}rnberg. (ITG-Fachbericht ; 250)}, booktitle = {Sensoren und Messsysteme 2014 ; Beitr{\"a}ge der 17. GMA/ITG-Fachtagung vom 3. bis 4. Juni 2014 in N{\"u}rnberg. (ITG-Fachbericht ; 250)}, publisher = {VDE-Verl.}, address = {D{\"u}sseldorf}, organization = {VDI/VDE-Gesellschaft Mess- und Automatisierungstechnik}, isbn = {978-3-8007-3622-5}, pages = {1 -- 4}, year = {2014}, language = {en} } @article{RatkeMilowLisinskietal.2014, author = {Ratke, Lorenz and Milow, Barbara and Lisinski, Susanne and Hoepfner, Sandra}, title = {On an effect of fine ceramic particles on the structure of aerogels}, series = {Microgravity science and technology}, volume = {26}, journal = {Microgravity science and technology}, publisher = {Springer Nature}, address = {Heidelberg}, issn = {0938-0108 ; 1875-0494}, doi = {10.1007/s12217-014-9380-2}, pages = {103 -- 110}, year = {2014}, language = {en} } @article{LeandroBungCarvalho2014, author = {Leandro, J. and Bung, Daniel B. and Carvalho, R.}, title = {Measuring void fraction and velocity fields of a stepped spillway for skimming flow using non-intrusive methods}, series = {Experiments in fluids}, journal = {Experiments in fluids}, number = {55}, publisher = {Springer Nature}, address = {Heidelberg}, issn = {0723-4864 (Print) ; 1432-1114 (Online)}, doi = {10.1007/s00348-014-1732-6}, pages = {Art. 1732}, year = {2014}, language = {en} } @inproceedings{BungOertel2014, author = {Bung, Daniel B. and Oertel, Mario}, title = {Manipulation of non-aerated cavity flow on a stepped spillway model}, series = {3rd European IAHR Congress : April 14 - 16, 2014, Porto}, booktitle = {3rd European IAHR Congress : April 14 - 16, 2014, Porto}, publisher = {Univ. of Porto}, address = {Porto}, organization = {International Association of Hydro-Environment Engineering and Research}, year = {2014}, language = {en} } @inproceedings{OertelBung2014, author = {Oertel, Mario and Bung, Daniel B.}, title = {Numerische Str{\"o}mungssimulation von Fließgew{\"a}ssern - Wo stehen wir und was werden wir im Laufe der n{\"a}chsten Jahre erreichen?}, series = {Simulationsverfahren und Modelle f{\"u}r Wasserbau und Wasserwirtschaft = Simulation techniques and models for hydraulic engineering and water management / 37. Dresdner Wasserbaukolloquium 2014, 13. - 14. M{\"a}rz 2014. (Dresdner wasserbauliche Mitteilungen ; H. 50)}, booktitle = {Simulationsverfahren und Modelle f{\"u}r Wasserbau und Wasserwirtschaft = Simulation techniques and models for hydraulic engineering and water management / 37. Dresdner Wasserbaukolloquium 2014, 13. - 14. M{\"a}rz 2014. (Dresdner wasserbauliche Mitteilungen ; H. 50)}, organization = {Dresdner Wasserbaukolloquium <37, 2014>}, isbn = {978-3-86780-349-6}, pages = {19 -- 30}, year = {2014}, language = {de} } @inproceedings{Bung2014, author = {Bung, Daniel B.}, title = {Observations on non-aerated flow and air entrainment on moderately sloped stepped spillways}, series = {7th Chinese-German Joint Symposium on Hydraulic and Ocean Engineering : 8. - 12. Sept. 2014, Hannover}, booktitle = {7th Chinese-German Joint Symposium on Hydraulic and Ocean Engineering : 8. - 12. Sept. 2014, Hannover}, organization = {Chinese-German Joint Symposium on Hydraulic and Ocean Engineering <7, 2014, Hannover>}, pages = {1 -- 8}, year = {2014}, language = {en} } @article{Laack2014, author = {Laack, Walter van}, title = {Nahtoderfahrungen aus medizinischer Sicht}, series = {Deutsche medizinische Wochenschrift : DMW}, volume = {Jg. 139}, journal = {Deutsche medizinische Wochenschrift : DMW}, number = {H. 51/52}, publisher = {Thieme}, address = {Stuttgart}, issn = {1439-4413 (E-Journal); 0012-0472 (Print); 1437-5982 (Print)}, doi = {10.1055/s-0034-1387363}, pages = {2651 -- 2654}, year = {2014}, abstract = {Nah- versus Nachtoderfahrungen Nahtoderfahrungen (NTE) sind ein Ph{\"a}nomen aus der Kategorie „außergew{\"o}hnliche Bewusstseinserfahrungen". Sie treten in unmittelbarer N{\"a}he des eigenen Todes auf. Oft, aber nicht immer, handelt es sich dabei um Erfahrungen von Personen, die durch {\"a}rztliche Maßnahmen wiederbelebt wurden und sp{\"a}ter davon berichten (NTE-ler). Jedoch kommen solche Ph{\"a}nomene auch bei Menschen vor, die w{\"a}hrend einer schweren Erkrankung eine lebensbedrohliche Krise haben, hiervon aber spontan genesen. Den NTE {\"a}hnlich sind auch sogenannte Nachtod-erfahrungen sowie spontane Erlebnisse, die im Rahmen anderer außergew{\"o}hnlicher Stresssituationen auftreten. Von Nachtoderfahrungen spricht man, wenn die Betroffenen anl{\"a}sslich des Todes von geliebten Angeh{\"o}rigen oder Freunden Erlebnisse haben, die inhaltlich ebenfalls, zumindest aber teilweise, denen von NTE entsprechen. Nachtoderfahrungen sowie spontane NTE-{\"a}hnliche Erlebnisse unterscheiden sich jedoch von den echten NTE zumeist sowohl quantitativ als auch qualitativ. Unter einem quantitativen Unterschied versteht man in diesem Zusammenhang eine in der Regel geringer ausgepr{\"a}gte Komplexit{\"a}t, als sie sehr vielen NTE zu eigen ist. Da sich aber auch viele NTE selbst bez{\"u}glich ihrer Komplexit{\"a}t unterscheiden, ist der Hauptunterschied qualitativer Natur: Echte NTE besitzen gegen{\"u}ber den anderen hier erw{\"a}hnten Ph{\"a}nomenen eine gr{\"o}ßere inhaltliche und emotionale Tiefe. Sie begleiten die Betroffenen anschließend ein Leben lang - zumeist mit positiven, in Einzelf{\"a}llen aber auch mit negativen Folgen, die bis zu einem sp{\"a}teren Suizid reichen k{\"o}nnen. Die genannten außergew{\"o}hnlichen Bewusstseinsph{\"a}nomene lassen sich in ihrer Gesamtheit bei rund 5 \% der Bev{\"o}lkerung finden. NTE im Speziellen haben hiervon einen durchaus bedeutenden Anteil. Je nach Studie geben zwischen 18 \% und 40 \% aller Personen, die reanimiert wurden, an, w{\"a}hrenddessen eine NTE erlebt zu haben. Dass nicht alle eine solche Erfahrung machen, wird von Kritikern gern dahingehend interpretiert, NTE seien rein physiologischer und keineswegs spiritueller Natur. Jedoch sollte man bedenken, dass im Fall einer rein neurophysiologischen Grundlage von NTE dann bei jedem ein solches Ph{\"a}nomen zu erwarten w{\"a}re, so wie beispielsweise auch die Symptome einer Hypoglyk{\"a}mie im Wesentlichen immer dieselben sind.}, language = {de} } @article{MuribYeapMartensetal.2014, author = {Murib, Mohammed Sharif and Yeap, Weng-Siang and Martens, Daan and Bienstman, Peter and Ceuninck, Ward de and Grinsven, Bart van and Sch{\"o}ning, Michael Josef and Michiels, Luc and Haenen, Ken and Ameloot, Marcel and Serpeng{\"u}zel, Ali and Wagner, Patrick}, title = {Photonic detection and characterization of DNA using sapphire microspheres}, series = {Journal of biomedical optics}, volume = {19}, journal = {Journal of biomedical optics}, number = {9}, publisher = {SPIE}, address = {Bellingham}, issn = {1560-2281 (E-Journal); 1083-3668 (Print)}, doi = {10.1117/1.JBO.19.9.097006}, pages = {097006}, year = {2014}, abstract = {A microcavity-based deoxyribonucleic acid (DNA) optical biosensor is demonstrated for the first time using synthetic sapphire for the optical cavity. Transmitted and elastic scattering intensity at 1510 nm are analyzed from a sapphire microsphere (radius 500  μm, refractive index 1.77) on an optical fiber half coupler. The 0.43 nm angular mode spacing of the resonances correlates well with the optical size of the sapphire sphere. Probe DNA consisting of a 36-mer fragment was covalently immobilized on a sapphire microsphere and hybridized with a 29-mer target DNA. Whispering gallery modes (WGMs) were monitored before the sapphire was functionalized with DNA and after it was functionalized with single-stranded DNA (ssDNA) and double-stranded DNA (dsDNA). The shift in WGMs from the surface modification with DNA was measured and correlated well with the estimated thickness of the add-on DNA layer. It is shown that ssDNA is more uniformly oriented on the sapphire surface than dsDNA. In addition, it is shown that functionalization of the sapphire spherical surface with DNA does not affect the quality factor (Q≈104) of the sapphire microspheres. The use of sapphire is especially interesting because this material is chemically resilient, biocompatible, and widely used for medical implants.}, language = {en} } @article{HandtkeVollandMethlingetal.2014, author = {Handtke, Stefan and Volland, Sonja and Methling, Karen and Albrecht, Dirk and Becher, D{\"o}rte and Nehls, Jenny and Bongaerts, Johannes and Maurer, Karl-Heinz and Lalk, Michael and Liesegang, Heiko and Voigt, Birgit and Daniel, Rolf and Hecker, Michael}, title = {Cell physiology of the biotechnological relevant bacterium Bacillus pumilus - An omics-based approach}, series = {Journal of Biotechnology}, journal = {Journal of Biotechnology}, number = {192(A)}, publisher = {Elsevier}, address = {Amsterdam}, issn = {1873-4863 (E-Journal); 0168-1656 (Print)}, doi = {10.1016/j.jbiotec.2014.08.028}, pages = {204 -- 214}, year = {2014}, abstract = {Members of the species Bacillus pumilus get more and more in focus of the biotechnological industry as potential new production strains. Based on exoproteome analysis, B. pumilus strain Jo2, possessing a high secretion capability, was chosen for an omics-based investigation. The proteome and metabolome of B. pumilus cells growing either in minimal or complex medium was analyzed. In total, 1542 proteins were identified in growing B. pumilus cells, among them 1182 cytosolic proteins, 297 membrane and lipoproteins and 63 secreted proteins. This accounts for about 43\% of the 3616 proteins encoded in the B. pumilus Jo2 genome sequence. By using GC-MS, IP-LC/MS and H NMR methods numerous metabolites were analyzed and assigned to reconstructed metabolic pathways. In the genome sequence a functional secretion system including the components of the Sec- and Tat-secretion machinery was found. Analysis of the exoproteome revealed secretion of about 70 proteins with predicted secretion signals. In addition, selected production-relevant genome features such as restriction modification systems and NRPS clusters of B. pumilus Jo2 are discussed.}, language = {en} } @inproceedings{PieperSchulz2014, author = {Pieper, Martin and Schulz, Silvia}, title = {Teaching Simulation Methods with COMSOL Multiphysics}, organization = {COMSOL Conference <2014, Cambridge>}, pages = {7}, year = {2014}, abstract = {This paper describes two courses on simulation methods for graduate students: "Simulation Methods" and "Simulation and Optimization in Virtual Engineering" The courses were planned to teach young engineers how to work with simulation software as well as to understand the necessary mathematical background. As simulation software COMSOL is used. The main philosophy was to combine theory and praxis in a way that motivates the students. In addition "soft skills" should be improved. This was achieved by project work as final examination. As underlying didactical principle the ideas of Bloom's revised taxonomy were followed. The paper basically focusses on educational aspects, e.g. how to structure the course, plan the exercises, organize the project work and include practical COMSOL examples.}, language = {en} } @inproceedings{SchirraWatmuffBauschat2014, author = {Schirra, Julian and Watmuff, Jon and Bauschat, J.-Michael}, title = {A relative assessment of existing potential-methodologies to accurately estimate the induced drag of highly non-planar lifting systems}, series = {Advanced aero concepts, design and operations : Applied Aerodynamics Conference : July 22 -24, 2014, Bristol, UK}, booktitle = {Advanced aero concepts, design and operations : Applied Aerodynamics Conference : July 22 -24, 2014, Bristol, UK}, organization = {Applied Aerodynamics Conference <2014, Bristol>}, pages = {1 -- 13}, year = {2014}, language = {en} } @incollection{KnottSofroniaGerressenetal.2014, author = {Knott, Thomas C. and Sofronia, Raluca E. and Gerressen, Marcus and Law, Yuen and Davidescu, Arjana and Savii, George G. and Gatzweiler, Karl-Heinz and Staat, Manfred and Kuhlen, Torsten W.}, title = {Preliminary bone sawing model for a virtual reality-based training simulator of bilateral sagittal split osteotomy}, series = {Biomedical simulation : 6th International Symposium, ISBMS 2014, Strasbourg, France, October 16-17, 2014 : proceedings (Lecture notes in computer science : vol. 8789)}, booktitle = {Biomedical simulation : 6th International Symposium, ISBMS 2014, Strasbourg, France, October 16-17, 2014 : proceedings (Lecture notes in computer science : vol. 8789)}, publisher = {Springer}, address = {Cham}, isbn = {978-3-319-12057-7 (Online)}, doi = {10.1007/978-3-319-12057-7_1}, pages = {1 -- 10}, year = {2014}, abstract = {Successful bone sawing requires a high level of skill and experience, which could be gained by the use of Virtual Reality-based simulators. A key aspect of these medical simulators is realistic force feedback. The aim of this paper is to model the bone sawing process in order to develop a valid training simulator for the bilateral sagittal split osteotomy, the most often applied corrective surgery in case of a malposition of the mandible. Bone samples from a human cadaveric mandible were tested using a designed experimental system. Image processing and statistical analysis were used for the selection of four models for the bone sawing process. The results revealed a polynomial dependency between the material removal rate and the applied force. Differences between the three segments of the osteotomy line and between the cortical and cancellous bone were highlighted.}, language = {en} } @inproceedings{WetterKern2014, author = {Wetter, Martin and Kern, Alexander}, title = {Number of lightning strikes to tall structures - comparison of calculations and measurements using a modern lightning monitoring system}, series = {2014 International Conference on Lightning Protection (ICLP), Shanghai, China}, booktitle = {2014 International Conference on Lightning Protection (ICLP), Shanghai, China}, organization = {International Conference on Lightning Protection <2014, Shanghai>}, pages = {1 -- 7}, year = {2014}, language = {en} } @book{Kurz2014, author = {Kurz, Melanie}, title = {Inspirationsmythen : zur Ideengeschichte des menschlichen Sch{\"o}pfungsverm{\"o}gens}, publisher = {Fink}, address = {Paderborn}, isbn = {978-3-7705-5760-8 (Druckausgabe)}, publisher = {Fachhochschule Aachen}, pages = {257 Seiten : Illustrationen}, year = {2014}, abstract = {Was ist Inspiration? Und wie entsteht der z{\"u}ndende Gedanke in den K{\"o}pfen von Kreativen, Forschern und Entwicklern? Diese Fragen besch{\"a}ftigen die Menschheit seit dem Altertum. Bereits vor etwa 3000 Jahren waren die wesentlichen Voraussetzungen f{\"u}r geistiges Sch{\"o}pfungsverm{\"o}gen bekannt. Doch dieses Wissen wird bald verdr{\"a}ngt, denn der geistig Sch{\"o}pfende selbst hat großes Interesse an der Verschleierung der Wahrheit. So entspinnen sich im Laufe der Kulturgeschichte immer neue, meist politisch intendierte Geschichten rund um den Inspirationsprozess und um die Sch{\"o}pferperson. Ein Ende dieser Verkl{\"a}rungen ist nicht absehbar. Aus diesem Grund widmet sich das vorliegende Buch den Irrwegen des Inspirationskonzepts sowie den ersten vier Musen, deren Namen f{\"u}r die tats{\"a}chlichen intrinsischen Vorg{\"a}nge bei der Ideengenerierung stehen.}, language = {de} } @book{Tietze2014, author = {Tietze, J{\"u}rgen}, title = {Einf{\"u}hrung in die angewandte Wirtschaftsmathematik : das praxisnahe Lehrbuch - inklusive Br{\"u}ckenkurs f{\"u}r Einsteiger. - 17. erw. Aufl.}, edition = {17., erw. Aufl.}, publisher = {Springer}, address = {Wiesbaden}, isbn = {978-3-658-02361-4 ; 978-3-658-02360-7}, pages = {XIV, 680 S. : graph. Darst.}, year = {2014}, language = {de} } @article{MalechaKlubertHeinenFuchs2014, author = {Malecha, Hartmut and Klubert, J. and Heinen-Fuchs, Sabine}, title = {Laserscanning passe? 3-D-Oberfl{\"a}chenmodelle aus Bilddaten und deren messtechnischer Nutzen}, series = {Wasserwirtschaft}, volume = {Jg. 104}, journal = {Wasserwirtschaft}, number = {Nr. 9}, publisher = {Springer Vieweg}, address = {Wiesbaden}, issn = {0043-0978}, pages = {32 -- 35}, year = {2014}, language = {de} } @article{NachtrodtTietschMostaccietal.2014, author = {Nachtrodt, Frederik and Tietsch, Wolfgang and Mostacci, Domiziano and Scherer, Ulrich W.}, title = {Set-up and first operation of a plasma oven for treatment of low level radioactive wastes}, series = {Nuclear technology and radiation protection}, volume = {29}, journal = {Nuclear technology and radiation protection}, number = {Suppl.}, publisher = {VINČA Institute of Nuclear Sciences}, address = {Belgrad}, issn = {1451-3994}, doi = {10.2298/NTRP140SS47N}, pages = {47 -- 51}, year = {2014}, language = {en} } @article{FateriGebhardtThuemmleretal.2014, author = {Fateri, Miranda and Gebhardt, Andreas and Th{\"u}mmler, Stefan and Thurn, Laura}, title = {Experimental investigation on selective laser melting of glass}, series = {Physics procedia : 8th International Conference on Laser Assisted Net Shape Engineering LANE 2014}, volume = {56 (2014)}, journal = {Physics procedia : 8th International Conference on Laser Assisted Net Shape Engineering LANE 2014}, publisher = {Elsevier}, address = {Amsterdam}, issn = {1875-3892 (E-Journal); 1875-3884 (Print)}, doi = {10.1016/j.phpro.2014.08.118}, pages = {357 -- 364}, year = {2014}, language = {en} } @article{SrivastavaLahiriMaitietal.2014, author = {Srivastava, A. and Lahiri, S. and Maiti, M. and Knolle, F. and Hoyler, Friedrich and Scherer, Ulrich W. and Schnug, E. W.}, title = {Study of naturally occurring radioactive material (NORM) in top soil of Punjab State from the North Western part of India}, series = {Journal of Radioanalytical and Nuclear Chemistry}, volume = {2014}, journal = {Journal of Radioanalytical and Nuclear Chemistry}, number = {302}, publisher = {Springer Nature}, address = {Basel}, issn = {1588-2780 (E-Journal); 0022-4081 (Print); 0134-0719 (Print); 0236-5731 (Print); 1417-2097 (Print)}, doi = {0.1007/s10967-014-3450-1}, pages = {1049 -- 1052}, year = {2014}, language = {en} } @article{SiqueiraMolinnusBegingetal.2014, author = {Siqueira, Jose R. and Molinnus, Denise and Beging, Stefan and Sch{\"o}ning, Michael Josef}, title = {Incorporating a hybrid urease-carbon nanotubes sensitive nanofilm on capacitive field-effect sensors for urea detection}, series = {Analytical chemistry}, volume = {86}, journal = {Analytical chemistry}, number = {11}, publisher = {ACS Publications}, address = {Columbus}, issn = {1520-6882 (E-Journal); 0003-2700 (Print); 0096-4484 (Print)}, doi = {10.1021/ac500458s}, pages = {5370 -- 5375}, year = {2014}, abstract = {The ideal combination among biomolecules and nanomaterials is the key for reaching biosensing units with high sensitivity. The challenge, however, is to find out a stable and sensitive film architecture that can be incorporated on the sensor's surface. In this paper, we report on the benefits of incorporating a layer-by-layer (LbL) nanofilm of polyamidoamine (PAMAM) dendrimer and carbon nanotubes (CNTs) on capacitive electrolyte-insulator-semiconductor (EIS) field-effect sensors for detecting urea. Three sensor arrangements were studied in order to investigate the adequate film architecture, involving the LbL film with the enzyme urease: (i) urease immobilized directly onto a bare EIS [EIS-urease] sensor; (ii) urease atop the LbL film over the EIS [EIS-(PAMAM/CNT)-urease] sensor; and (iii) urease sandwiched between the LbL film and another CNT layer [EIS-(PAMAM/CNT)-urease-CNT]. The surface morphology of all three urea-based EIS biosensors was investigated by atomic force microscopy (AFM), while the biosensing abilities were studied by means of capacitance-voltage (C/V) and dynamic constant-capacitance (ConCap) measureaments at urea concentrations ranging from 0.1 mM to 100 mM. The EIS-urease and EIS-(PAMAM/CNT)-urease sensors showed similar sensitivity (∼18 mV/decade) and a nonregular signal behavior as the urea concentration increased. On the other hand, the EIS-(PAMAM/CNT)-urease-CNT sensor exhibited a superior output signal performance and higher sensitivity of about 33 mV/decade. The presence of the additional CNT layer was decisive to achieve a urea based EIS sensor with enhanced properties. Such sensitive architecture demonstrates that the incorporation of an adequate hybrid enzyme-nanofilm as sensing unit opens new prospects for biosensing applications using the field-effect sensor platform.}, language = {en} } @inproceedings{HellmannsFischerDilgeretal.2014, author = {Hellmanns, Mark and Fischer, F. and Dilger, K. and Wittor, B. and Hildebrand, J. and Werner, F.}, title = {Applikation und Einsatz von faserverst{\"a}rkten Klebstoffen im Bauwesen abgeschlossenes IGF-Projekt Nr. 16956 B (DVS 08.072, Laufzeit 01.02.2011 - 31.01.2013)}, series = {Tagungsband / 14. Kolloquium Gemeinsame Forschung in der Klebtechnik : 18. und 19. Februar 2014, DECHEMA-Haus, Frankfurt am Main}, booktitle = {Tagungsband / 14. Kolloquium Gemeinsame Forschung in der Klebtechnik : 18. und 19. Februar 2014, DECHEMA-Haus, Frankfurt am Main}, organization = {DECHEMA, Gesellschaft f{\"u}r Chemische Technik und Biotechnologie}, pages = {26 -- 27}, year = {2014}, language = {de} } @article{FeichtingerEilmannBuchmannetal.2014, author = {Feichtinger, Linda M. and Eilmann, Britta and Buchmann, Nina and Rigling, Andreas}, title = {Growth adjustments of conifers to drought and to century-long irrigation}, series = {Forest Ecology and Management}, volume = {2014}, journal = {Forest Ecology and Management}, number = {334}, publisher = {Elsevier}, address = {Amsterdam}, issn = {1872-7042 (Online)}, doi = {10.1016/j.foreco.2014.08.008}, pages = {96 -- 105}, year = {2014}, abstract = {Our knowledge on tree responses to drought is mainly based on short-term manipulation experiments which do not capture any possible long-term adjustments in this response. Therefore, historical water channels in inner-Alpine dry valleys were used as century-long irrigation experiments to investigate adjustments in tree growth to contrasting water supply. This involved quantifying the tree-ring growth of irrigated and non-irrigated (control) Scots pine (Pinus sylvestris L.) in Valais (Switzerland), as well as European larch (Larix decidua Mill.) and black pine (Pinus nigra Arnold) in Vinschgau (Italy). Furthermore, the adjustments in radial growth of Scots pine and European larch to an abrupt stop in irrigation were analyzed. Irrigation promoted the radial growth of all tree species investigated compared to the control: (1) directly through increased soil water availability, and (2) indirectly through increased soil nutrients and humus contents in the irrigated plots. Irrigation led to a full elimination of growth responses to climate for European larch and black pine, but not for Scots pine, which might become more sensitive to drought with increasing tree size in Valais. For the control trees, the response of the latewood increment to water availability in July/August has decreased in recent decades for all species, but increased in May for Scots pine only. The sudden irrigation stop caused a drop in radial growth to a lower level for Scots pine or similar level for larch compared to the control for up to ten years. However, both tree species were then able to adjust to the new conditions and subsequently grew with similar (Scots pine) or even higher growth rates (larch) than the control. To estimate the impact of climate change on future forest development, the duration of manipulation experiments should be on longer time scales in order to capture adjustment processes and feedback mechanisms of forest ecosystems.}, language = {en} } @article{EilmannSterckWegneretal.2014, author = {Eilmann, Britta and Sterck, Frank J. and Wegner, L. and de Vries, Sven M. G. and von Arx, G. and Mohren, Godefridus M. J. and den Ouden, Jan and Sass-Klaassen, Ute G. W.}, title = {Wood structural differences between northern and southern beech provenances growing at a moderate site}, series = {Tree Physiology}, volume = {34}, journal = {Tree Physiology}, number = {8}, publisher = {Oxford University Press}, address = {Oxford}, issn = {1758-4469 (Online)}, doi = {10.1093/treephys/tpu069}, pages = {882 -- 893}, year = {2014}, language = {en} } @inproceedings{VoronkovaBauerKotliar2014, author = {Voronkova, Eva B. and Bauer, Svetlana M. and Kotliar, Konstantin}, title = {Computer simulation of the cornea-scleral shell as applied to pressure-volume relationship in the human eye}, series = {2014 International Conference on Computer Technologies in Physical and Engineering Applications : ICCTPEA 2014 : proceedings : June 30 2014-July 4 2014, St. Petersburg}, booktitle = {2014 International Conference on Computer Technologies in Physical and Engineering Applications : ICCTPEA 2014 : proceedings : June 30 2014-July 4 2014, St. Petersburg}, organization = {Institute of Electrical and Electronics Engineers}, isbn = {978-1-4799-5315-8}, pages = {204 -- 205}, year = {2014}, language = {en} } @misc{ReyesOchoa2014, type = {Master Thesis}, author = {Reyes Ochoa, Leonel}, title = {Engineering aspects of a parabolic trough collector field with direct steam generation and an organic rankine cycle}, publisher = {Fachhochschule Aachen}, address = {Aachen}, pages = {X, 72 S.}, year = {2014}, language = {en} } @article{AlmajhdiSengerAmeretal.2014, author = {Almajhdi, Fahad N. and Senger, Tilo and Amer, Haitham M. and Gissmann, Lutz and {\"O}hlschl{\"a}ger, Peter}, title = {Design of a highly effective therapeutic HPV16 E6/E7-specific DNA vaccine: optimization by different ways of sequence rearrangements (Shuffling)}, series = {PLOS one}, volume = {11}, journal = {PLOS one}, number = {9}, publisher = {PLOS}, address = {San Francisco}, issn = {1932-6203}, doi = {10.1371/journal.pone.0113461}, pages = {Artikel e113461}, year = {2014}, abstract = {Persistent infection with the high-risk Human Papillomavirus type 16 (HPV 16) is the causative event for the development of cervical cancer and other malignant tumors of the anogenital tract and of the head and neck. Despite many attempts to develop therapeutic vaccines no candidate has entered late clinical trials. An interesting approach is a DNA based vaccine encompassing the nucleotide sequence of the E6 and E7 viral oncoproteins. Because both proteins are consistently expressed in HPV infected cells they represent excellent targets for immune therapy. Here we report the development of 8 DNA vaccine candidates consisting of differently rearranged HPV-16 E6 and E7 sequences within one molecule providing all naturally occurring epitopes but supposedly lacking transforming activity. The HPV sequences were fused to the J-domain and the SV40 enhancer in order to increase immune responses. We demonstrate that one out of the 8 vaccine candidates induces very strong cellular E6- and E7- specific cellular immune responses in mice and, as shown in regression experiments, efficiently controls growth of HPV 16 positive syngeneic tumors. This data demonstrates the potential of this vaccine candidate to control persistent HPV 16 infection that may lead to malignant disease. It also suggests that different sequence rearrangements influence the immunogenecity by an as yet unknown mechanism.}, language = {en} } @book{KernWettingfeld2014, author = {Kern, Alexander and Wettingfeld, J{\"u}rgen}, title = {Blitzschutzsysteme 1 : allgemeine Grunds{\"a}tze, Risikomanagement, Schutz von baulichen Anlagen und Personen ; Erl{\"a}uterungen zu den Normen DIN EN 62305-1 (VDE 0185-305-1):2011-10, DIN EN 62305-2 (VDE 0185-305-2):2013-02, DIN EN 62305-3 (VDE 0185-305-3):2011-10. (VDE-Schriftenreihe Normen verst{\"a}ndlich ; 44)}, publisher = {VDE-Verl.}, address = {Berlin [u.a.]}, isbn = {978-3-8007-3511-2}, pages = {308 S.}, year = {2014}, language = {de} } @book{Tietze2014, author = {Tietze, J{\"u}rgen}, title = {{\"U}bungsbuch zur angewandten Wirtschaftsmathematik : Aufgaben, Testklausuren und ausf{\"u}hrliche L{\"o}sungen. - 9., {\"u}berarb. u. erw. Aufl.}, edition = {9., {\"u}berarb. u. erw. Aufl.}, publisher = {Vieweg + Teubner}, address = {Wiesbaden}, isbn = {978-3-658-06874-5 ; 978-3-658-06873-8}, pages = {VIII, 444 S.}, year = {2014}, language = {de} } @book{SchneiderSchneider2014, author = {Schneider, Bettina and Schneider, Wilhelm}, title = {Jahresabschluss und Jahresabschlussanalyse : systematische Darstellung in {\"U}bersichten. (Reihe Betriebswirtschaftslehre in {\"U}bersichten ; 2)}, edition = {5. Aufl., Studienausg.}, publisher = {Cuvillier}, address = {G{\"o}ttingen}, isbn = {978-3-95404-828-1}, pages = {Getr. Z{\"a}hlung : graph. Darst.}, year = {2014}, language = {de} } @book{Gebhardt2014, author = {Gebhardt, Andreas}, title = {3D-Drucken : Grundlagen und Anwendungen des Additive Manufacturing (AM)}, publisher = {Hanser}, address = {M{\"u}nchen}, isbn = {978-3-446-44238-2 ; 978-3-446-44237-5}, pages = {XIII, 186 S.}, year = {2014}, language = {de} } @article{MuellerHirschfeldLambertzetal.2014, author = {M{\"u}ller, Martin and Hirschfeld, Julian and Lambertz, Rita and Schulze Lohoff, Andreas and Lustfeld, Hans and Pfeifer, Heinz and Reißel, Martin}, title = {Validation of a novel method for detecting and stabilizing malfunctioning areas in fuel cell stacks}, series = {Journal of power sources}, volume = {272}, journal = {Journal of power sources}, publisher = {Elsevier}, address = {Amsterdam}, issn = {1873-2755 (E-Journal); 0378-7753 (Print)}, doi = {10.1016/j.jpowsour.2014.08.045}, pages = {225 -- 232}, year = {2014}, abstract = {In this paper a setup for detecting malfunctioning areas of MEAs in fuel cell stacks is described. Malfunctioning areas generate electric cross currents inside bipolar plates. To exploit this we suggest bipolar plates consisting not of two but of three layers. The third one is a highly conducting layer and segmented such that the cross currents move along the segments to the surface of the stack where they can be measured by an inductive sensor. With this information a realistic model can be used to detect the malfunctioning area. Furthermore the third layer will prevent any current inhomogeneity of a malfunctioning cell to spread to neighbouring cells in the stack. In this work the results of measurements in a realistic cell setup will be compared with the results obtained in simulation studies with the same configuration. The basis for the comparison is the reliable characterisation of the electrical properties of the cell components and the implication of these results into the simulation model. The experimental studies will also show the limits in the maximum number of segments, which can be used for a reliable detection of cross currents.}, language = {en} } @article{KluczkaEcksteinAlexopoulosetal.2014, author = {Kluczka, Sven and Eckstein, Julian and Alexopoulos, Spiros and Vaeßen, Christiane and Roeb, Martin}, title = {Process simulation for solar steam and dry reforming}, series = {Energy procedia : Proceedings of the SolarPACES 2013 International Conference}, volume = {49}, journal = {Energy procedia : Proceedings of the SolarPACES 2013 International Conference}, publisher = {Elsevier}, address = {Amsterdam}, issn = {1876-6102 (E-Journal)}, doi = {10.1016/j.egypro.2014.03.092}, pages = {850 -- 859}, year = {2014}, abstract = {In co-operation with the German Aerospace Center, the Solar-Institut J{\"u}lich has been analyzing the different technologies that are available for methanol production from CO2 using solar energy. The aim of the project is to extract CO2 from industrial exhaust gases or directly from the atmosphere to recycle it by use of solar energy. Part of the study was the modeling and simulating of a methane reformer for the production of synthesis gas, which can be operated by solar or hybrid heat sources. The reformer has been simplified in such a way that the model is accurate and enables fast calculations. The developed pseudo-homogeneous one- dimensional model can be regarded as a kind of counter-current heat exchanger and is able to incorporate a steam reforming reaction as well as a dry reforming reaction.}, language = {en} } @inproceedings{FunkeHajAyedKustereretal.2014, author = {Funke, Harald and Haj Ayed, A. and Kusterer, K. and Keinz, Jan and Kazari, M. and Kitajima, J. and Horikawa, A. and Okada, K.}, title = {Numerical Study on Increased Energy Density for the DLN Micromix Hydrogen Combustion Principle}, series = {Combustion, Fuels and Emissions (ASME Turbo Expo 2014: Turbine Technical Conference and Exposition : D{\"u}sseldorf, Germany, June 16-20, 2014 ; Vol. 4A)}, booktitle = {Combustion, Fuels and Emissions (ASME Turbo Expo 2014: Turbine Technical Conference and Exposition : D{\"u}sseldorf, Germany, June 16-20, 2014 ; Vol. 4A)}, publisher = {ASME}, address = {New York, N.Y.}, isbn = {978-0-7918-4568-4}, pages = {V04AT04A057}, year = {2014}, language = {en} } @book{Timme2014, author = {Timme, Michael}, title = {Wohnungseigentumsgesetz : Gesetz {\"u}ber das Wohnungseigentum und das Dauerwohnrecht; Kommentar / Timme [Hrsg.]}, edition = {2. Aufl.}, publisher = {Beck}, address = {M{\"u}nchen}, isbn = {978-3-406-66025-2}, pages = {XIII, 1395 S.}, year = {2014}, language = {de} } @article{Timme2014, author = {Timme, Michael}, title = {BGH: Geltendmachung von Sachm{\"a}ngeln bei Wohnungseigentum}, series = {LMK : Fachdienst Zivilrecht : Kommentierte BGH-Rechtsprechung}, volume = {2014}, journal = {LMK : Fachdienst Zivilrecht : Kommentierte BGH-Rechtsprechung}, number = {5}, publisher = {Beck}, address = {M{\"u}nchen}, issn = {1611-1095}, year = {2014}, language = {de} } @incollection{Timme2014, author = {Timme, Michael}, title = {Begriffsbestimmungen}, series = {Wohnungseigentumsgesetz : Gesetz {\"u}ber das Wohnungseigentum und das Dauerwohnrecht ; Kommentar}, booktitle = {Wohnungseigentumsgesetz : Gesetz {\"u}ber das Wohnungseigentum und das Dauerwohnrecht ; Kommentar}, edition = {2. Auflage}, publisher = {Beck}, address = {M{\"u}nchen}, isbn = {978-3-406-66025-2}, pages = {1 -- 23}, year = {2014}, language = {de} } @inproceedings{PfaffSappler2014, author = {Pfaff, Raphael and Sappler, Magnus}, title = {TRANSPACT : die automatische Mittelpufferkupplung f{\"u}r attraktiven G{\"u}terverkehr}, series = {RAIL-FREIGHT 2014 : Zukunft des Schieneng{\"u}terverkehrs ; Technologie - {\"O}konomie - {\"O}kologie - Verkehrspolitik ; [Tagungsdokumentation des IV. Internationalen Fachsymposiums zum Thema Schieneng{\"u}terverkehr] (Bahntechnik Aktuell ; 48)}, booktitle = {RAIL-FREIGHT 2014 : Zukunft des Schieneng{\"u}terverkehrs ; Technologie - {\"O}konomie - {\"O}kologie - Verkehrspolitik ; [Tagungsdokumentation des IV. Internationalen Fachsymposiums zum Thema Schieneng{\"u}terverkehr] (Bahntechnik Aktuell ; 48)}, publisher = {Verl. d. IFV Bahntechnik}, address = {Berlin}, isbn = {978-3-940727-41-1}, pages = {121 -- 128}, year = {2014}, language = {de} } @inproceedings{RousseauKern2014, author = {Rousseau, Alain and Kern, Alexander}, title = {How to deal with environmental risk in IEC 62305-2}, series = {2014 International Conference on Lightning Protection (ICLP), Shanghai, China}, booktitle = {2014 International Conference on Lightning Protection (ICLP), Shanghai, China}, organization = {International Conference on Lightning Protection <2014, Shanghai>}, pages = {521 -- 527}, year = {2014}, abstract = {The 2nd edition of the lightning risk management standard (IEC 62305-2) considers structures, which may endanger environment. In these cases, the loss is not limited to the structure itself, which is valid for usual structures. In the past (Edition 1) this danger was simply taken into account by a special hazard factor, multiplying the existing risk for the structure with a number. Now, in the edition 2, we add to the risk for the structure itself a "second risk" due to the losses outside the structure. The losses outside can be treated independently from what occurs inside. This is a major advantage to analyze the risk for sensitive structures, like chemical plants, nuclear plants, or structures containing explosives, etc. In this paper, the existing procedure given by the European version EN 62305-2 Ed.2 is further developed and applied to a few structures.}, language = {en} } @inproceedings{KernBraun2014, author = {Kern, Alexander and Braun, Christian}, title = {Risk management according to IEC 62305-2 edition 2: 2010-12 assessment of structures with a risk of explosion}, series = {2014 International Conference on Lightning Protection (ICLP), Shanghai, China}, booktitle = {2014 International Conference on Lightning Protection (ICLP), Shanghai, China}, organization = {International Conference on Lightning Protection <2014, Shanghai>}, pages = {1237 -- 1242}, year = {2014}, abstract = {Risk management for structures with a risk of explosion should be considered very carefully when performing a risk analysis according to IEC 62305-2. In contrast to the 2006 edition of the standard, the 2010 edition describes the topic "Structures with a risk of explosion" in more detail. Moreover, in Germany separate procedures and parameters are defined for the risk analysis of structures with a risk of explosion (Supplement 3 of the German DIN EN 62305-2 standard). This paper describes the contents and the relevant calculations of this Supplement 3, together with a numerical example.}, language = {en} } @article{GuoSekiMiyamotoetal.2014, author = {Guo, Yuanyuan and Seki, Kosuke and Miyamoto, Ko-ichiro and Wagner, Torsten and Sch{\"o}ning, Michael Josef and Yoshinobu, Tatsuo}, title = {Device simulation of the light-addressable potentiometric sensor with a novel photoexcitation method for a higher spatial resolution}, series = {Procedia Engineering}, volume = {87}, journal = {Procedia Engineering}, publisher = {Elsevier}, address = {Amsterdam}, issn = {1877-7058}, doi = {10.1016/j.proeng.2014.11.369}, pages = {456 -- 459}, year = {2014}, abstract = {A novel photoexcitation method for the light-addressable potentiometric sensor (LAPS) realized a higher spatial resolution of chemical imaging. In this method, a modulated light probe, which generates the alternating photocurrent signal, is surrounded by a ring of constant light, which suppresses the lateral diffusion of photocarriers by enhancing recombination. A device simulation verified that a higher spatial resolution could be obtained by adjusting the gap between the modulated and constant light. It was also found that a higher intensity and a longer wavelength of constant light was more effective. However, there exists a tradeoff between the spatial resolution and the amplitude of the photocurrent, and thus, the signal-to-noise ratio. A tilted incidence of constant light was applied, which could achieve even higher resolution with a smaller loss of photocurrent.}, language = {en} } @article{MiyamotoSekiWagneretal.2014, author = {Miyamoto, K. and Seki, K. and Wagner, Torsten and Sch{\"o}ning, Michael Josef and Yoshinobu, T.}, title = {Enhancement of the spatial resolution of the chemical imaging sensor by a hybrid fiber-optic illumination}, series = {Procedia Engineering}, volume = {87}, journal = {Procedia Engineering}, publisher = {Elsevier}, address = {Amsterdam}, issn = {1877-7058}, doi = {10.1016/j.proeng.2014.11.563}, pages = {612 -- 615}, year = {2014}, abstract = {The chemical imaging sensor, which is based on the principle of the light-addressable potentiometric sensor (LAPS), is a powerful tool to visualize the spatial distribution of chemical species on the sensor surface. The spatial resolution of this sensor depends on the diffusion of photocarriers excited by a modulated light. In this study, a novel hybrid fiber-optic illumination was developed to enhance the spatial resolution. It consists of a modulated light probe to generate a photocurrent signal and a ring of constant light, which suppresses the lateral diffusion of minority carriers excited by the modulated light. It is demonstrated that the spatial resolution was improved from 92 μm to 68 μm.}, language = {en} } @article{BronderWuPoghossianetal.2014, author = {Bronder, Thomas and Wu, Chunsheng and Poghossian, Arshak and Werner, Frederik and Keusgen, M. and Sch{\"o}ning, Michael Josef}, title = {Label-free detection of DNA hybridization with light-addressable potentiometric sensors: comparison of various DNA-immobilization strategies}, series = {Procedia Engineering}, volume = {87}, journal = {Procedia Engineering}, publisher = {Elsevier}, address = {Amsterdam}, issn = {1877-7058}, doi = {10.1016/j.proeng.2014.11.647}, pages = {755 -- 758}, year = {2014}, abstract = {Light-addressable potentiometric sensors (LAPS) consisting of a p-Si-SiO2 and p-Si-SiO2-Au structure, respectively, have been tested for a label-free electrical detection of DNA (deoxyribonucleic acid) hybridization. Three different strategies for immobilizing single-stranded probe DNA (ssDNA) molecules on a LAPS surface have been studied and compared: (a) immobilization of thiol-modified ssDNA on the patterned Au surface via gold-thiol bond, (b) covalent immobilization of amino-modified ssDNA onto the SiO2 surface functionalized with 3-aminopropyltriethoxysilane and (c) layer-by-layer adsorption of negatively charged ssDNA on a positively charged weak polyelectrolyte layer of poly(allylamine hydrochloride).}, language = {en} } @article{HuckPoghossianBaeckeretal.2014, author = {Huck, Christina and Poghossian, Arshak and B{\"a}cker, Matthias and Reisert, Steffen and Schubert, J. and Zander, W. and Begoyan, V. K. and Buniatyan, V. V. and Sch{\"o}ning, Michael Josef}, title = {Chemical sensors based on a high-k perovskite oxide of barium strontium titanate}, series = {Procedia Engineering}, volume = {87}, journal = {Procedia Engineering}, publisher = {Elsevier}, address = {Amsterdam}, issn = {1877-7058}, doi = {10.1016/j.proeng.2014.11.258}, pages = {28 -- 31}, year = {2014}, abstract = {High-k perovskite oxide of barium strontium titanate (BST) represents a very attractive multi-functional transducer material for the development of (bio-)chemical sensors for liquids. In this work, BST films have been applied as a sensitive transducer material for a label-free detection of adsorbed charged macromolecules (positively charged polyelectrolytes) and concentration of hydrogen peroxide vapor as well as protection insulator layer for a contactless electrolyte-conductivity sensor. The experimental results of characterization of individual sensors are presented. Special emphasis is devoted towards the development of a capacitively-coupled contactless electrolyte-conductivity sensor.}, language = {en} } @article{SchusserBaeckerKrischeretal.2014, author = {Schusser, Sebastian and B{\"a}cker, Matthias and Krischer, M. and Wenzel, L. and Leinhos, Marcel and Poghossian, Arshak and Biselli, Manfred and Wagner, P. and Sch{\"o}ning, Michael Josef}, title = {Enzymatically catalyzed degradation of biodegradable polymers investigated by means of a semiconductor-based field-effect sensor}, series = {Procedia Engineering}, volume = {87}, journal = {Procedia Engineering}, publisher = {Elsevier}, address = {Amsterdam}, issn = {1877-7058}, doi = {10.1016/j.proeng.2014.11.689}, pages = {1314 -- 1317}, year = {2014}, abstract = {A semiconductor field-effect device has been used for an enzymatically catalyzed degradation of biopolymers for the first time. This novel technique is capable to monitor the degradation process of multiple samples in situ and in real-time. As model system, the degradation of the biopolymer poly(D, L-lactic acid) has been monitored in the degradation medium containing the enzyme lipase from Rhizomucor miehei. The obtained results demonstrate the potential of capacitive field-effect sensors for degradation studies of biodegradable polymers.}, language = {en} } @misc{NoetzoldBragardFinketal.2014, author = {N{\"o}tzold, K. and Bragard, Michael and Fink, K. and Griessel, R. and Wegener, R.}, title = {Cascaded H-bridge converter with transformer based cell power balancing in each voltage level : [Patentschrift]}, publisher = {Europ{\"a}isches Patentamt / United States Patent and Trademark Office [u.a.]}, address = {Den Haag / Alexandria, VA}, pages = {16 S. : graph. Darst.}, year = {2014}, language = {en} } @book{Muehl2014, author = {M{\"u}hl, Thomas}, title = {Einf{\"u}hrung in die elektrische Messtechnik : Grundlagen, Messverfahren, Anwendungen. - 4. aktualisierte u. erw. Aufl.}, edition = {4., aktualisierte u. erw. Aufl.}, publisher = {Springer}, address = {Wiesbaden}, isbn = {978-3-8348-2063-1 ; 978-3-8348-0899-8}, pages = {XI, 320 S.}, year = {2014}, language = {de} } @article{Balzer2014, author = {Balzer, Hermann}, title = {Ausgestaltung und Steuerung des Netzes von Bankbeziehungen - Update nach 25 Jahren mithilfe einer explorativen Unternehmensbefragung / Arbeitskreis Finanzierung der Schmalenbach-Gesellschaft e.V. unter Mitarb. von Prof. Dr. Hermann Balzer...}, series = {Zfbf : Schmalenbachs Zeitschrift f{\"u}r betriebswirtschaftliche Forschung}, journal = {Zfbf : Schmalenbachs Zeitschrift f{\"u}r betriebswirtschaftliche Forschung}, number = {H. 8}, publisher = {Springer Gabler}, address = {Wiesbaden}, issn = {0341-2687}, pages = {694 -- 723}, year = {2014}, language = {de} } @article{Stulpe2014, author = {Stulpe, Werner}, title = {From the attempt of certain classical reformulations of quantum mechanics to quasi-probability representations}, series = {Journal of Mathematical Physics}, volume = {55}, journal = {Journal of Mathematical Physics}, number = {1}, publisher = {AIP Publishing}, address = {College Park, Md.}, issn = {222-488}, doi = {10.1063/1.4861939}, pages = {Artikel 012109}, year = {2014}, abstract = {The concept of an injective affine embedding of the quantum states into a set of classical states, i.e., into the set of the probability measures on some measurable space, as well as its relation to statistically complete observables is revisited, and its limitation in view of a classical reformulation of the statistical scheme of quantum mechanics is discussed. In particular, on the basis of a theorem concerning a non-denseness property of a set of coexistent effects, it is shown that an injective classical embedding of the quantum states cannot be supplemented by an at least approximate classical description of the quantum mechanical effects. As an alternative approach, the concept of quasi-probability representations of quantum mechanics is considered.}, language = {en} } @article{DachwaldMikuckiTulaczyketal.2014, author = {Dachwald, Bernd and Mikucki, Jill and Tulaczyk, Slawek and Digel, Ilya and Espe, Clemens and Feldmann, Marco and Francke, Gero and Kowalski, Julia and Xu, Changsheng}, title = {IceMole : A maneuverable probe for clean in situ analysis and sampling of subsurface ice and subglacial aquatic ecosystems}, series = {Annals of Glaciology}, volume = {55}, journal = {Annals of Glaciology}, number = {65}, publisher = {Cambridge University Press}, address = {Cambridge}, issn = {1727-5644}, doi = {10.3189/2014AoG65A004}, pages = {14 -- 22}, year = {2014}, abstract = {There is significant interest in sampling subglacial environments for geobiological studies, but they are difficult to access. Existing ice-drilling technologies make it cumbersome to maintain microbiologically clean access for sample acquisition and environmental stewardship of potentially fragile subglacial aquatic ecosystems. The IceMole is a maneuverable subsurface ice probe for clean in situ analysis and sampling of glacial ice and subglacial materials. The design is based on the novel concept of combining melting and mechanical propulsion. It can change melting direction by differential heating of the melting head and optional side-wall heaters. The first two prototypes were successfully tested between 2010 and 2012 on glaciers in Switzerland and Iceland. They demonstrated downward, horizontal and upward melting, as well as curve driving and dirt layer penetration. A more advanced probe is currently under development as part of the Enceladus Explorer (EnEx) project. It offers systems for obstacle avoidance, target detection, and navigation in ice. For the EnEx-IceMole, we will pay particular attention to clean protocols for the sampling of subglacial materials for biogeochemical analysis. We plan to use this probe for clean access into a unique subglacial aquatic environment at Blood Falls, Antarctica, with return of a subglacial brine sample.}, language = {en} } @article{LevesqueSiegwolfEilmannetal.2014, author = {L{\´e}vesque, Mathieu and Siegwolf, Rolf and Eilmann, Britta and Saurer, Matthias and Rigling, Andreas}, title = {Increased water-use efficiency does not lead to enhanced tree growth under xeric and mesic conditions}, series = {New Phytologist}, volume = {203}, journal = {New Phytologist}, number = {1}, publisher = {Wiley-Blackwell}, address = {Oxford}, issn = {1469-8137 (Online)}, doi = {10.1111/nph.12772}, pages = {94 -- 109}, year = {2014}, language = {en} } @inproceedings{NeumannFerreinKallweitetal.2014, author = {Neumann, Tobias and Ferrein, Alexander and Kallweit, Stephan and Scholl, Ingrid}, title = {Towards a mobile mapping robot for underground mines}, series = {7th Conference of Robotics and Mechatronics : RobMech 2014 : 27th and 28th Nov. 2014, Cape Town}, booktitle = {7th Conference of Robotics and Mechatronics : RobMech 2014 : 27th and 28th Nov. 2014, Cape Town}, organization = {Conference of Robotics and Mechatronics <7, 2014, Cape Town, South Africa>}, pages = {1 -- 6}, year = {2014}, language = {en} } @incollection{AlhwarinFerreinScholl2014, author = {Alhwarin, Faraj and Ferrein, Alexander and Scholl, Ingrid}, title = {IR stereo kinect: improving depth images by combining structured light with IR stereo}, series = {PRICAI 2014: Trends in artificial intelligence : 13th Pacific Rim International Conference on Artificial Intelligence : Gold Coast, QLD, Australia, December 1-5, 2014 : proceedings. (Lecture notes in computer science ; vol. 8862)}, booktitle = {PRICAI 2014: Trends in artificial intelligence : 13th Pacific Rim International Conference on Artificial Intelligence : Gold Coast, QLD, Australia, December 1-5, 2014 : proceedings. (Lecture notes in computer science ; vol. 8862)}, publisher = {Springer}, address = {M{\"u}nchen}, isbn = {978-3-319-13559-5 (Print) ; 978-3-319-13560-1 (E-Book)}, doi = {10.1007/978-3-319-13560-1_33}, pages = {409 -- 421}, year = {2014}, abstract = {RGB-D sensors such as the Microsoft Kinect or the Asus Xtion are inexpensive 3D sensors. A depth image is computed by calculating the distortion of a known infrared light (IR) pattern which is projected into the scene. While these sensors are great devices they have some limitations. The distance they can measure is limited and they suffer from reflection problems on transparent, shiny, or very matte and absorbing objects. If more than one RGB-D camera is used the IR patterns interfere with each other. This results in a massive loss of depth information. In this paper, we present a simple and powerful method to overcome these problems. We propose a stereo RGB-D camera system which uses the pros of RGB-D cameras and combine them with the pros of stereo camera systems. The idea is to utilize the IR images of each two sensors as a stereo pair to generate a depth map. The IR patterns emitted by IR projectors are exploited here to enhance the dense stereo matching even if the observed objects or surfaces are texture-less or transparent. The resulting disparity map is then fused with the depth map offered by the RGB-D sensor to fill the regions and the holes that appear because of interference, or due to transparent or reflective objects. Our results show that the density of depth information is increased especially for transparent, shiny or matte objects.}, language = {en} } @article{DemnyHebel2014, author = {Demny, Andreas and Hebel, Christoph}, title = {Rechnergest{\"u}tzte Ermittlung der Verbindungsfunktionsstufen und der verbindungsbezogenen Angebotsqualit{\"a}t nach den Richtlinien f{\"u}r integrierte Netzgestaltung nach RIN 2008}, series = {Straßenverkehrstechnik : Organ der Forschungsgesellschaft f{\"u}r Straßen- und Verkehrswesen, der Bundesvereinigung der Straßenbau- und Verkehrsingenieure und der {\"O}sterreichischen Forschungsgesellschaft Straße und Verkehr ; Zeitschrift f{\"u}r Verkehrsplanung, Verkehrsmanagement, Verkehrssicherheit, Verkehrstechnik}, volume = {Jg. 58}, journal = {Straßenverkehrstechnik : Organ der Forschungsgesellschaft f{\"u}r Straßen- und Verkehrswesen, der Bundesvereinigung der Straßenbau- und Verkehrsingenieure und der {\"O}sterreichischen Forschungsgesellschaft Straße und Verkehr ; Zeitschrift f{\"u}r Verkehrsplanung, Verkehrsmanagement, Verkehrssicherheit, Verkehrstechnik}, number = {H. 12}, publisher = {Kirschbaum Verlag}, address = {Bonn}, issn = {0039-2219}, pages = {811 -- 820}, year = {2014}, language = {de} } @incollection{Hebel2014, author = {Hebel, Christoph}, title = {Mehrwert}, series = {Unser Dorf hat Zukunft}, booktitle = {Unser Dorf hat Zukunft}, publisher = {St{\"a}dteRegion Aachen}, address = {Aachen}, pages = {6 -- 7}, year = {2014}, language = {de} } @article{Thomas2014, author = {Thomas, Axel}, title = {Generation Y}, series = {P.T. : Magazin f{\"u}r Wirtschaft und Gesellschaft}, volume = {10}, journal = {P.T. : Magazin f{\"u}r Wirtschaft und Gesellschaft}, number = {3}, publisher = {OPS Netzwerk}, address = {Leipzig}, issn = {1860-501X}, pages = {6 -- 9}, year = {2014}, language = {de} } @article{ThomasWassenberg2014, author = {Thomas, Axel and Wassenberg, Gerd}, title = {Erfolgreich sein im Kampf um die besten Talente : Employer Branding}, series = {Wirtschaftliche Nachrichten der Industrie- und Handelskammer Aachen}, journal = {Wirtschaftliche Nachrichten der Industrie- und Handelskammer Aachen}, publisher = {IHK Aachen}, address = {Aachen}, year = {2014}, language = {de} } @inproceedings{FateriGebhardt2014, author = {Fateri, Miranda and Gebhardt, Andreas}, title = {Jewelry fabrication via selective laser melting of glass}, series = {ASME 2014 12th Biennial Conference on Engineering Systems Design and Analysis Volume 1: Applied Mechanics; Automotive Systems; Biomedical Biotechnology Engineering; Computational Mechanics; Design; Digital Manufacturing; Education; Marine and Aerospace Applications}, booktitle = {ASME 2014 12th Biennial Conference on Engineering Systems Design and Analysis Volume 1: Applied Mechanics; Automotive Systems; Biomedical Biotechnology Engineering; Computational Mechanics; Design; Digital Manufacturing; Education; Marine and Aerospace Applications}, isbn = {978-0-7918-4583-7}, doi = {10.1115/ESDA2014-20380}, pages = {V001T06A005}, year = {2014}, abstract = {Selective Laser Melting (SLM) is one of the Additive Manufacturing (AM) technologies applicable for producing complex geometries which are typically expensive or difficult to fabricate using conventional methods. This process has been extensively investigated experimentally for various metals and the fabrication process parameters have been established for different applications; however, fabricating 3D glass objects using SLM technology has remained a challenge so far although it could have many applications. This paper presents a summery on various experimental evaluations of a material database incorporating the build parameters of glass powder using the SLM process for jewelry applications.}, language = {en} } @incollection{Benner2014, author = {Benner, Joachim}, title = {Berechnungsmethoden der W{\"a}lzlagerreibung und Einflussgr{\"o}ßen}, series = {SMK 2014 : Schweizer Maschinenelemente Kolloquim 25. und 26. November 2014}, booktitle = {SMK 2014 : Schweizer Maschinenelemente Kolloquim 25. und 26. November 2014}, publisher = {TUDpress Verl. der Wissenschaften}, address = {Dresden}, isbn = {978-3-944331-81-2}, pages = {151 -- 170}, year = {2014}, language = {de} } @article{Wollert2014, author = {Wollert, J{\"o}rg}, title = {Funkstandards f{\"u}r Sensornetzwerke}, series = {Elektronik : Fachmedium f{\"u}r industrielle Anwender und Entwickler}, volume = {Bd. 63}, journal = {Elektronik : Fachmedium f{\"u}r industrielle Anwender und Entwickler}, number = {H. 12}, publisher = {WEKA-Fachmedien}, address = {Haar}, issn = {0013-5658}, pages = {36 -- 41}, year = {2014}, language = {de} } @article{Wollert2014, author = {Wollert, J{\"o}rg}, title = {Echtzeit-Ethernet : Protokoll-Reigen}, series = {Elektronik : Fachmedium f{\"u}r industrielle Anwender und Entwickler}, volume = {Bd. 63}, journal = {Elektronik : Fachmedium f{\"u}r industrielle Anwender und Entwickler}, number = {H. 26}, publisher = {WEKA-Fachmedien}, address = {Haar}, issn = {0013-5658}, pages = {24 -- 31}, year = {2014}, language = {de} } @article{Wollert2014, author = {Wollert, J{\"o}rg}, title = {Der Embedded Wireless-Report}, series = {Elektronik : Fachmedium f{\"u}r industrielle Anwender und Entwickler ; Sonderh. Wireless : Fachmedium f{\"u}r Entwicklungen funkbasierter Systeme}, journal = {Elektronik : Fachmedium f{\"u}r industrielle Anwender und Entwickler ; Sonderh. Wireless : Fachmedium f{\"u}r Entwicklungen funkbasierter Systeme}, publisher = {WEKA-Fachmedien}, address = {Haar}, issn = {0013-5658}, pages = {18 -- 25}, year = {2014}, language = {de} } @article{Wollert2014, author = {Wollert, J{\"o}rg}, title = {Echtzeit-Ethernet mit Standardtechnik}, series = {Elektronik : Fachmedium f{\"u}r industrielle Anwender und Entwickler ; Sonderh. Embedded : Fachmagazin f{\"u}r die Entwicklung von Embedded-Systemen}, volume = {Bd. 63}, journal = {Elektronik : Fachmedium f{\"u}r industrielle Anwender und Entwickler ; Sonderh. Embedded : Fachmagazin f{\"u}r die Entwicklung von Embedded-Systemen}, number = {H. 12}, publisher = {WEKA-Fachmedien}, address = {Haar}, issn = {0013-5658}, pages = {28 -- 32}, year = {2014}, language = {de} } @inproceedings{HuberRauStreblowetal.2014, author = {Huber, Max and Rau, Sebastian and Streblow, Rita and Wollert, J{\"o}rg and M{\"u}ller, Dirk}, title = {L{\"u}ftungskan{\"a}le als Funkstrecke}, series = {Jahreskolloquium Kommunikation in der Automation (KommA 2014) : Lemgo, 18.11.2014 / J{\"u}rgen Jasperneite ... (Hrsg.)}, booktitle = {Jahreskolloquium Kommunikation in der Automation (KommA 2014) : Lemgo, 18.11.2014 / J{\"u}rgen Jasperneite ... (Hrsg.)}, organization = {Jahreskolloquium Kommunikation in der Automation <5, 2014, Lemgo>}, isbn = {978-3-9814062-4-5}, pages = {1 -- 8}, year = {2014}, language = {de} } @inproceedings{GebhardtRitzSiekmannetal.2014, author = {Gebhardt, Andreas and Ritz, Thomas and Siekmann, Kirsten and Wallenborn, Ramona}, title = {Additive manufacturing businesses in the process chain of individualized mass products}, series = {DDMC 2014 : Proceedings of the Fraunhofer Direct Digital Manufacturing Conference}, booktitle = {DDMC 2014 : Proceedings of the Fraunhofer Direct Digital Manufacturing Conference}, editor = {Demmer, Axel}, publisher = {Fraunhofer}, address = {Stuttgart}, isbn = {978-3-8396-9128-1 (E-Book)}, year = {2014}, language = {en} } @inproceedings{RitzIzquierdoTelloDamm2014, author = {Ritz, Thomas and Izquierdo Tello, C{\´e}sar and Damm, Sebastian}, title = {Connecting a pedelec to the cloud as basis for gamification in multi modal mobility planning}, series = {MobileCloud 2014 : 2nd IEEE International Conference on Mobile Cloud Computing, Services, and Engineering Oxford, United Kingdom 7-10 April 2014}, booktitle = {MobileCloud 2014 : 2nd IEEE International Conference on Mobile Cloud Computing, Services, and Engineering Oxford, United Kingdom 7-10 April 2014}, publisher = {IEEE Service Center}, address = {Piscataway, NJ}, isbn = {978-1-4799-2504-9}, doi = {10.1109/MobileCloud.2014.25}, pages = {101 -- 108}, year = {2014}, language = {en} } @inproceedings{OegunKlingHeuermannetal.2014, author = {{\"O}gun, Celal Mohan and Kling, Rainer and Heuermann, Holger and Gr{\"a}ser, Ulrich and Schopp, Christoph}, title = {Elektrodenlose quecksilberfreie Niederdrucklampen betrieben mit Mikrowellen}, series = {Licht 2014 [Elektronische Ressource] : Den Haag, Holland ; 21. Gemeinschaftstagung, 21. bis 24. September 2014 ; Tagungsband}, booktitle = {Licht 2014 [Elektronische Ressource] : Den Haag, Holland ; 21. Gemeinschaftstagung, 21. bis 24. September 2014 ; Tagungsband}, publisher = {Nederlandse Stichting voor Verlichtingskunde}, address = {Ede}, pages = {[Elektronische Ressource]}, year = {2014}, language = {de} } @inproceedings{HeuermannFinger2014, author = {Heuermann, Holger and Finger, Torsten}, title = {2.45 GHz Plasma Powered Spark Plug by Thermal and EM-Optimization}, pages = {30 Folien}, year = {2014}, language = {en} } @article{RaueWambachGloeggleretal.2014, author = {Raue, Markus and Wambach, M. and Gl{\"o}ggler, S. and Grefen, Dana and Kaufmann, R. and Abetz, C. and Georgopanos, P. and Handge, U. A. and Mang, Thomas and Bl{\"u}mich, B. and Abetz, V.}, title = {Investigation of historical hard rubber ornaments of Charles Goodyear}, series = {Macromolecular chemistry and physics}, volume = {Vol. 215}, journal = {Macromolecular chemistry and physics}, number = {No. 3}, publisher = {Wiley-VCH}, address = {Weinheim}, issn = {1022-1352}, pages = {245 -- 254}, year = {2014}, language = {en} } @inproceedings{HoettgesMueller2014, author = {H{\"o}ttges, J{\"o}rg and M{\"u}ller, Andreas}, title = {Einsatz von GIS und CAD zur Schaffung langfristig nutzbarer Planungsdaten}, series = {15. K{\"o}lner Kanal- und Kl{\"a}ranlagen-Kolloquium : 1. und 2. Oktober 2014 im Maternushaus, K{\"o}ln / ISA, Inst. und Lehrstuhl f{\"u}r Siedlungswasserwirtschaft und Siedlungsabfallwirtschaft der RWTH Aachen ... Hrsg. von J. Pinnekamp. Bearb. von V. K{\"o}lling}, booktitle = {15. K{\"o}lner Kanal- und Kl{\"a}ranlagen-Kolloquium : 1. und 2. Oktober 2014 im Maternushaus, K{\"o}ln / ISA, Inst. und Lehrstuhl f{\"u}r Siedlungswasserwirtschaft und Siedlungsabfallwirtschaft der RWTH Aachen ... Hrsg. von J. Pinnekamp. Bearb. von V. K{\"o}lling}, publisher = {Ges. zur F{\"o}rderung der Siedlungswasserwirtschaft an der RWTH Aachen}, address = {Aachen}, organization = {FH Aachen, University of Applied Sciences}, isbn = {978-3-938996-74-4}, pages = {12/1 -- 12/12}, year = {2014}, language = {de} } @techreport{RitzSiekmannWallenborn2014, author = {Ritz, Thomas and Siekmann, Kirsten and Wallenborn, Ramona}, title = {3D-Druck - Prozessmanagement f{\"u}r individualisierte Massenprodukte : Wie k{\"o}nnen Fertigungsdienstleister in die endkundengerichtete Produktion integriert werden? ; Info-Brosch{\"u}re}, publisher = {eBusiness-Lotse}, address = {Aachen}, pages = {16 S. : Ill., graph. Darst.}, year = {2014}, abstract = {Die Informationsbrosch{\"u}re „3D-Druck - Prozessmanagement f{\"u}r individualisierte Massenprodukte" richtet sich an 3D-Druckdienstleister, die additive Fertigungsverfahren (Additive Manufacturing) nutzen, sowie an IT-Dienstleister, die eine Plattform f{\"u}r den Datenaustausch und die Individualisierung anbieten. Mit der additiven 3D-Drucktechnologie erfolgt die Fertigung von Produkten durch einen schichtweisen Aufbau. In dieser Brosch{\"u}re werden m{\"o}gliche Potenziale im Bereich der Herstellung mittels additiver Fertigungsverfahren aufgezeigt.}, language = {de} } @techreport{LessenichRitzWallenborn2014, author = {Leßenich, Nina and Ritz, Thomas and Wallenborn, Ramona}, title = {Prototyping zur Verbesserung der Benutzerfreundlichkeit mobiler Software : Potenziale benutzerfreundlicher Software-Entwicklung ; Info-Brosch{\"u}re}, publisher = {eBusiness-Lotse}, address = {Aachen}, pages = {7 S. : Ill., graph. Darst.}, year = {2014}, abstract = {Mobile Anwendungen nehmen mit der Verbreitung von Smartphones zu. Die Akzeptanz der Nutzer bestimmt den Erfolg solcher mobiler Applikationen dabei maßgeblich. Um diese Anerkennung zu schaffen, ist eine m{\"o}glichst hohe Gebrauchstauglichkeit, auch Usability genannt, notwendig. Die Informationsbrosch{\"u}re „Prototyping zur Verbesserung der Benutzerfreundlichkeit mobiler Software" richtet sich an Personen, die an der Gestaltung und entwicklung von (mobiler) Software beteiligt sind. In dieser Brosch{\"u}re werden m{\"o}gliche Potenziale im Bereich einer effizienten und benutzerzentrierten Software-Entwicklung aufgezeigt.}, language = {de} } @techreport{PisarczykRitzWallenborn2014, author = {Pisarczyk, Rafael and Ritz, Thomas and Wallenborn, Ramona}, title = {Unterschiedliche Entwicklungsans{\"a}tze von Multiplattform-Anwendungen : Markt{\"u}bersicht}, publisher = {eBusiness-Lotse}, address = {Aachen}, pages = {15 S. : Ill., graph. Darst.}, year = {2014}, abstract = {Die Markt{\"u}bersicht „Unterschiedliche Entwicklungsans{\"a}tze von Multiplattform-Anwendungen" richtet sich an IT-Dienstleister, Entwickler und IT-Abteilungen von Unternehmen, die Multiplattform Anwendungen entwickeln. In dieser Markt{\"u}bersicht werden verschiedene Entwicklungsans{\"a}tze beschrieben und ihre jeweiligen Vor- und Nachteile aufgezeigt.}, language = {de} } @article{WallenbornRitz2014, author = {Wallenborn, Ramona and Ritz, Thomas}, title = {Mobilit{\"a}t miteinander teilen : st{\"a}dtisches eCarsharing in einer vernetzten Gesellschaft ; [vernetztes Fahren von morgen]}, series = {Neue Mobilit{\"a}t : das Magazin vom Bundesverband eMobilit{\"a}t}, volume = {5}, journal = {Neue Mobilit{\"a}t : das Magazin vom Bundesverband eMobilit{\"a}t}, number = {14 (Herbstausg.)}, publisher = {Bundesverband eMobilit{\"a}t BEM}, address = {Berlin}, issn = {2191-5636}, pages = {92 -- 95}, year = {2014}, language = {de} } @techreport{RitzSiekmannWallenborn2014, author = {Ritz, Thomas and Siekmann, Kirsten and Wallenborn, Ramona}, title = {Anforderungen an die Gestaltung multimodaler Mobilit{\"a}tsanwendungen : Potenziale f{\"u}r die IT-Branche bei der Organisation der verkehrsmittel{\"u}bergreifenden Mobilit{\"a}t von morgen am Beispiel CarSharing und privater PKW ; Info-Brosch{\"u}re}, publisher = {eBusiness-Lotse}, address = {Aachen}, pages = {7 S. : Ill., graph. Darst.}, year = {2014}, abstract = {Die Informationsbrosch{\"u}re „Anforderungen an die Gestaltung multimodaler Mobilit{\"a}tsanwendungen" richtet sich an IT-Dienstleister. In dieser Brosch{\"u}re werden m{\"o}gliche Potenziale im Bereich des allgemeinen Mobilit{\"a}tsmanagements aufgezeigt. Automobilhersteller vernetzten sich zunehmend mit Technologie-Unternehmen. Es geht nicht nur um die besondere Entwicklung von spezieller Elektronik- und Softwarel{\"o}sungen f{\"u}r Navigations- und Entertainmentsysteme oder auch Fahrassistenz-Systemen in modernen PKW, sondern um einen {\"u}bergreifenden Design- und Interaktionsansatz f{\"u}r miteinander vernetzte Ger{\"a}te.}, language = {de} } @techreport{DammIzquierdoTelloRitzetal.2014, author = {Damm, Sebastian and Izquierdo Tello, C{\´e}sar and Ritz, Thomas and Wallenborn, Ramona}, title = {Konzept f{\"u}r einen spielerischen Ansatz zur multimodalen Mobilit{\"a}tsplanung : Potenziale f{\"u}r die IT-Branche bei der Organisation der Mobilit{\"a}t von morgen am Beispiel eines Elektrofahrrads und Cloud-Computing ; Info-Brosch{\"u}re}, publisher = {eBusiness-Lotse}, address = {Aachen}, pages = {9 S. : Ill., graph. Darst.}, year = {2014}, abstract = {Die Informationsbrosch{\"u}re "Konzept f{\"u}r einen spielerischen Ansatz zur multimodalen Mobilit{\"a}tsplanung" richtet sich an Spiele- und System-Designer sowie Entwickler. In dieser Brosch{\"u}re werden m{\"o}gliche Potenziale im Bereich des allgemeinen Mobilit{\"a}tsmanagements aufgezeigt, Automobilhersteller vernetzten sich zunehmend mit Technologie-Unternehmen.}, language = {de} } @techreport{RahierRitzWallenborn2014, author = {Rahier, Michael and Ritz, Thomas and Wallenborn, Ramona}, title = {Elektromobilit{\"a}t in einer vernetzten Welt : Potenziale f{\"u}r die IT-Branche bei der Organisation der Mobilit{\"a}t von morgen ; Info-Brosch{\"u}re}, publisher = {eBusiness-Lotse}, address = {Aachen}, pages = {9 S. : Ill., graph. Darst.}, year = {2014}, abstract = {Die Informationsbrosch{\"u}re „Elektromobilit{\"a}t in einer vernetzten Welt" richtet sich an IT-Dienstleister. In dieser Brosch{\"u}re werden m{\"o}gliche Potenziale im Bereich der Elektromobilit{\"a}t aufgezeigt. Die Mobilit{\"a}t der Zukunft ist eine interdisziplin{\"a}re Angelegenheit und kein reines Automotive-Thema mehr. Beispiele wie Mobilit{\"a}tsmanagement, eCommerce und Individualisierung sind im Mobilit{\"a}tsbereich f{\"u}r die IT-Branche relevant.}, language = {de} } @inproceedings{SchoppHeuermannHoltrup2014, author = {Schopp, Christoph and Heuermann, Holger and Holtrup, S.}, title = {Investigation on efficacy optimization of RF-driven automotive D-lamps}, series = {44th European Microwave Conference (EuMC),2014, Rome}, booktitle = {44th European Microwave Conference (EuMC),2014, Rome}, doi = {10.1109/EuMC.2014.6986645}, pages = {1154 -- 1157}, year = {2014}, language = {en} } @incollection{HeuermannFinger2014, author = {Heuermann, Holger and Finger, Torsten}, title = {Microwave Spark Plug for Very High-Pressure Conditions}, series = {Ignition systems for gasoline engines}, booktitle = {Ignition systems for gasoline engines}, editor = {G{\"u}nther, Michael}, publisher = {DCM Druck}, address = {Meckenheim}, pages = {269 -- 282}, year = {2014}, language = {en} } @book{Heuermann2014, author = {Heuermann, Holger}, title = {Mikrowellentechnik}, edition = {4. Aufl.}, pages = {[Elektronische Ressource] IX, 225 S. ; graph. Darst.}, year = {2014}, language = {de} } @article{Wollert2014, author = {Wollert, J{\"o}rg}, title = {Feldbustechnologie}, series = {Factory : der Durchblick in der Technik}, journal = {Factory : der Durchblick in der Technik}, publisher = {WEKA-Industriemedien}, address = {Wien}, pages = {Publ. online}, year = {2014}, language = {de} } @article{RitzPisarczykSachtlebenetal.2014, author = {Ritz, Thomas and Pisarczyk, Rafael and Sachtleben, Johanna and Leßenich, Nina}, title = {Usability Engineering maßgeschneidert : Modellbaukasten zur Entwicklung gebrauchstauglicher mobiler Software}, series = {Wissenschaft trifft Praxis}, volume = {1}, journal = {Wissenschaft trifft Praxis}, number = {1}, publisher = {Begleitforschung Mittelstand-Digital c/o WIK-Consult GmbH}, address = {Bad Honnef}, issn = {2198-8544 (Print)}, pages = {79 -- 88}, year = {2014}, language = {de} } @inproceedings{KraftZoell2014, author = {Kraft, Bodo and Z{\"o}ll, Axel}, title = {Von der Langstrecke zum Sprint - Agile Methoden in traditionellen Unternehmen}, series = {Projektmanagement und Vorgehensmodelle 2014 : soziale Aspekte und Standardisierung}, booktitle = {Projektmanagement und Vorgehensmodelle 2014 : soziale Aspekte und Standardisierung}, editor = {Engstler, Martin}, publisher = {Gesellschaft f{\"u}r Informatik}, address = {Bonn}, organization = {FH Aachen, University of Applied Sciences}, isbn = {978-3-88579-630-5}, pages = {35 -- 46}, year = {2014}, language = {de} } @article{HafnerDemetzWeickertetal.2014, author = {Hafner, David and Demetz, Oliver and Weickert, Joachim and Reißel, Martin}, title = {Mathematical Foundations and Generalisations of the Census Transform for Robust Optic Flow Computation}, series = {Journal of Mathematical Imaging and Vision}, journal = {Journal of Mathematical Imaging and Vision}, publisher = {Springer}, address = {New York}, issn = {1573-7683 (Online)}, doi = {10.1007/s10851-014-0529-9}, year = {2014}, language = {en} } @article{FredebeulKrein2014, author = {Fredebeul-Krein, Markus}, title = {Ziele der Sozial- und Verteilungspolitik}, series = {Das Wirtschaftsstudium : wisu ; Zeitschrift f{\"u}r Ausbildung, Pr{\"u}fung, Berufseinstieg und Fortbildung}, volume = {43}, journal = {Das Wirtschaftsstudium : wisu ; Zeitschrift f{\"u}r Ausbildung, Pr{\"u}fung, Berufseinstieg und Fortbildung}, number = {7}, publisher = {Lange}, address = {D{\"u}sseldorf}, issn = {0340-3084}, pages = {907 -- 912}, year = {2014}, language = {de} } @article{FredebeulKreinSteingroever2014, author = {Fredebeul-Krein, Markus and Steingr{\"o}ver, Markus}, title = {Wholesale broadband access to IPTV in an NGA environment : how to deal with it from a regulatory perspective?}, series = {Telecommunications Policy}, volume = {38}, journal = {Telecommunications Policy}, number = {3}, publisher = {Elsevier}, address = {Amsterdam}, issn = {0308-5961 (Print)}, doi = {doi:10.1016/j.telpol.2013.04.002}, pages = {264 -- 277}, year = {2014}, language = {en} } @inproceedings{Huening2014, author = {H{\"u}ning, Felix}, title = {Power semiconductors : key components for HEV/EV}, series = {FISITA 2014 World Automotive Congress : 2 - 6 June, Maastricht, the Netherlands International Federation of Automotive Engineering Societies}, booktitle = {FISITA 2014 World Automotive Congress : 2 - 6 June, Maastricht, the Netherlands International Federation of Automotive Engineering Societies}, publisher = {KIVI}, address = {[s.l.]}, pages = {1 USB-Speicherstick}, year = {2014}, language = {en} } @inproceedings{Goldbach2014, author = {Goldbach, Daniel}, title = {Diagnosemaßnahmen im Umfeld der Funktionalen Sicherheit}, series = {AmE 2014 - Automotive meets electronics [Elektronische Ressource] : Beitr{\"a}ge der 5. GMM-Fachtagung vom 18. bis 19. Februar 2014 in Dortmund / Veranst.: VDE/VDI-Gesellschaft Mikroelektronik, Mikrosystem- und Feinwerktechnik (GMM)}, booktitle = {AmE 2014 - Automotive meets electronics [Elektronische Ressource] : Beitr{\"a}ge der 5. GMM-Fachtagung vom 18. bis 19. Februar 2014 in Dortmund / Veranst.: VDE/VDI-Gesellschaft Mikroelektronik, Mikrosystem- und Feinwerktechnik (GMM)}, editor = {Wahl, Michael}, publisher = {VDE-Verl.}, address = {Berlin}, isbn = {978-3-8007-3580-8}, pages = {172 -- 179}, year = {2014}, language = {de} } @inproceedings{AnthrakidisHerrmannMirzaetal.2014, author = {Anthrakidis, Anette and Herrmann, Ulf and Mirza, M. F. and Schorn, Christian and Schwarzer, Klemens and Wedding, Philipp and Weis, Fabian}, title = {Parabolrinnenentwicklung und Qualifizierung am Solar-Institut J{\"u}lich}, series = {Thermische Solarenergie : 24. Symposium ; 7. bis 9. Mai 2014, Kloster Banz, Bad Staffelstein}, booktitle = {Thermische Solarenergie : 24. Symposium ; 7. bis 9. Mai 2014, Kloster Banz, Bad Staffelstein}, publisher = {OTTI}, address = {Regensburg}, organization = {Ostbayerisches Technologie-Transfer-Institut}, isbn = {978-3-943891-35-5}, pages = {242 -- 243}, year = {2014}, language = {de} } @article{Sillius2014, author = {Sillius, Sarah}, title = {„Viele machen gutes Marketing, ohne es zu wissen" : zwei Experten von FH [Prof. Dr. Gert Hoepner] und RWTH Aachen [Prof. Dr. Daniel Mentzel] erkl{\"a}ren, wie Unternehmen ihre Zielgruppe besser erreichen}, series = {Wirtschaftliche Nachrichten : das Magazin f{\"u}r Unternehmen / Industrie- und Handelskammer Aachen}, volume = {2014}, journal = {Wirtschaftliche Nachrichten : das Magazin f{\"u}r Unternehmen / Industrie- und Handelskammer Aachen}, number = {3}, publisher = {IHK Aachen}, address = {Aachen}, pages = {16 -- 18}, year = {2014}, language = {de} } @article{HuberStreblowMuelleretal.2014, author = {Huber, M. and Streblow, R. and M{\"u}ller, D. and Lange, S. and Joneleit, R. and Sefker, T. and Rau, Sebastian and Wollert, J{\"o}rg}, title = {Funksignal{\"u}bertragung in Luftleitungen}, series = {HLH : L{\"u}ftung, Klima, Heizung, Sanit{\"a}r, Geb{\"a}udetechnik}, volume = {Bd. 65}, journal = {HLH : L{\"u}ftung, Klima, Heizung, Sanit{\"a}r, Geb{\"a}udetechnik}, number = {H. 7/8}, issn = {1436-5103}, pages = {36 -- 40}, year = {2014}, language = {de} } @inproceedings{JanotteFecklerKoetteretal.2014, author = {Janotte, N. and Feckler, G. and K{\"o}tter, Jens and Decker, Stefan and Herrmann, Ulf and Schmitz, Mark and L{\"u}pfert, E.}, title = {Dynamic performance evaluation of the HelioTrough® collector demonstration loop : towards a new benchmark in parabolic trough qualification}, series = {SolarPACES International Conference 2013, Las Vegas, Nevada, USA, 17 - 20 September 2013 : [proceedings]. - Pt. 1. - (Energy procedia ; 49)}, booktitle = {SolarPACES International Conference 2013, Las Vegas, Nevada, USA, 17 - 20 September 2013 : [proceedings]. - Pt. 1. - (Energy procedia ; 49)}, publisher = {Curran}, address = {Red Hook, NY}, isbn = {978-1-63266-904-9}, issn = {1876-6102}, doi = {10.1016/j.egypro.2014.03.012}, pages = {109 -- 117}, year = {2014}, language = {en} } @techreport{HoepnerSiers2014, author = {Hoepner, Gert and Siers, Carsten}, title = {6. Studie Vertriebskompass / durchgef{\"u}hrt von der FH Aachen und der Siers \& Collegen GmbH}, publisher = {FH Aachen}, address = {Aachen}, organization = {FH Aachen}, pages = {35 Bl.}, year = {2014}, language = {de} } @article{MartinGonzalezKotliarRiosMartinezetal.2014, author = {Martin-Gonzalez, Anabel and Kotliar, Konstantin and Rios-Martinez, Jorge and Lanzl, Ines and Navab, Nassir}, title = {Mediated-reality magnification for macular degeneration rehabilitation}, series = {Journal of Modern Optics}, volume = {61}, journal = {Journal of Modern Optics}, number = {17}, publisher = {Taylor \& Francis}, address = {London}, issn = {1362-3044}, doi = {10.1080/09500340.2014.936110}, pages = {1400 -- 1408}, year = {2014}, language = {en} } @incollection{BorchertBremen2014, author = {Borchert, J{\"o}rg and Bremen, Frank}, title = {Gesch{\"a}fts- und Organisationsmodelle f{\"u}r ein Strom- und Gas-Portfoliomanagement}, series = {Optimierte Strom- und Gasbeschaffung in der Energiewirtschaftsbranche}, booktitle = {Optimierte Strom- und Gasbeschaffung in der Energiewirtschaftsbranche}, publisher = {KS-Energy-Verl.}, address = {Berlin}, isbn = {978-3-9813142-9-8}, pages = {11 -- 28}, year = {2014}, language = {de} } @incollection{BurgerKirschMarcheretal.2014, author = {Burger, Ulrich and Kirsch, Ansgar and Marcher, Thomas and H{\"o}ser, Sebastian}, title = {Geologisch-geotechnischer Planungsprozess von Tunnelbauten mit Schwerpunkt tiefliegender Tunnel}, series = {Beton-Kalender ; Bd. 103: Unterirdisches Bauen, Grundbau, Eurocode 7}, booktitle = {Beton-Kalender ; Bd. 103: Unterirdisches Bauen, Grundbau, Eurocode 7}, publisher = {Ernst}, address = {Berlin}, isbn = {978-3-433-03051-6 ; 978-3-433-60335-2 ; 978-3-433-60508-0 ; 3-433-60508-4}, pages = {37 -- 62}, year = {2014}, language = {de} } @inproceedings{LenzWolf2014, author = {Lenz, Laura L. and Wolf, Martin}, title = {Economic evaluation of serious games with the comparative assessment framework COSEGA}, series = {The shift from teaching to learning : individual, collective and organizational learning through gaming simulation ; proceedings of the 45th conference of the International Simulation and Gaming Association, Dornbirn 2014}, booktitle = {The shift from teaching to learning : individual, collective and organizational learning through gaming simulation ; proceedings of the 45th conference of the International Simulation and Gaming Association, Dornbirn 2014}, editor = {Kritz, Willy Christian}, publisher = {Bertelsmann}, address = {[Bielefeld]}, isbn = {978-3-7639-5422-3}, pages = {374 -- 386}, year = {2014}, language = {en} } @article{KuertenMottaghyZiegler2014, author = {K{\"u}rten, Sylvia and Mottaghy, Darius and Ziegler, Martin}, title = {Planung, Auslegung und Dimensionierung von thermo-aktiven Bauteilen am Beispiel thermo-aktiver Abdichtungselemente}, series = {Geothermie, Bohr- und Brunnentechnik}, journal = {Geothermie, Bohr- und Brunnentechnik}, publisher = {Ernst \& Sohn}, address = {Berlin}, pages = {18 -- 20}, year = {2014}, language = {de} } @article{RathMottaghy2014, author = {Rath, V. and Mottaghy, Darius}, title = {Klimainformation aus dem Untergrund?}, series = {Geographische Rundschau}, volume = {66}, journal = {Geographische Rundschau}, number = {7-8}, publisher = {Westermann}, address = {Braunschweig}, issn = {0016-7460}, pages = {30 -- 36}, year = {2014}, language = {de} } @article{VogtMottaghyRathetal.2014, author = {Vogt, C. and Mottaghy, Darius and Rath, V. and Marquart, G. and Dijkshoorn, L. and Wolf, A. and Clauser, C.}, title = {Vertical variation in heat flow on the Kola Peninsula: palaeoclimate or fluid flow?}, series = {Geophysical Journal International}, volume = {199}, journal = {Geophysical Journal International}, number = {2}, publisher = {Oxford University Press}, address = {Oxford}, issn = {1365-246X}, doi = {10.1093/gji/ggu282}, pages = {829 -- 843}, year = {2014}, abstract = {Following earlier studies, we present forward and inverse simulations of heat and fluid transport of the upper crust using a local 3-D model of the Kola area. We provide best estimates for palaeotemperatures and permeabilities, their errors and their dependencies. Our results allow discriminating between the two mentioned processes to a certain extent, partly resolving the non-uniqueness of the problem. We find clear indications for a significant contribution of advective heat transport, which, in turn, imply only slightly lower ground surface temperatures during the last glacial maximum relative to the present value. These findings are consistent with the general background knowledge of (i) the fracture zones and the corresponding fluid movements in the bedrock and (ii) the glacial history of the Kola area.}, language = {en} } @inproceedings{KirschFelberMarcheretal.2014, author = {Kirsch, Ansgar and Felber, W. and Marcher, Thomas and Fuchs, W.}, title = {Geotechnical challenges during design and construction of a ski resort in Azerbaijan}, series = {Geotechnics of roads and railways : proceedings of the 15th Danube - European Conference on Geotechnical Engineering : 9-11 September 2014, Vienna, Austria}, booktitle = {Geotechnics of roads and railways : proceedings of the 15th Danube - European Conference on Geotechnical Engineering : 9-11 September 2014, Vienna, Austria}, publisher = {{\"O}IAV - {\"O}sterreichischer Ingenieur- und Architekten-Verein}, address = {Wien}, organization = {Danube - European Conference on Geotechnical Engineering <15, 2014, Wien>}, isbn = {978-3-902593-01-6}, pages = {757 -- 762}, year = {2014}, language = {en} } @incollection{Lind2014, author = {Lind, Thorsten Patric}, title = {Insolvenzverwalter, Organe der Gl{\"a}ubiger : \S\S 56-62, 66-72, 74-79}, series = {Fachanwaltskommentar Insolvenzrecht / hrsg. von Martin Ahrens; Markus Gehrlein; Andreas Ringstmeier . - 2. Aufl.}, booktitle = {Fachanwaltskommentar Insolvenzrecht / hrsg. von Martin Ahrens; Markus Gehrlein; Andreas Ringstmeier . - 2. Aufl.}, publisher = {Luchterhand}, address = {K{\"o}ln}, isbn = {978-3-472-08559-1}, pages = {649 - 703; 728 - 745; 748 - 762}, year = {2014}, language = {de} } @incollection{Lind2014, author = {Lind, Thorsten Patric}, title = {Verwaltung und Verwertung der Insolvenzmasse : \S\S 148 - 164}, series = {Fachanwaltskommentar Insolvenzrecht / hrsg. von Martin Ahrens; Markus Gehrlein; Andreas Ringstmeier . - 2. Aufl.}, booktitle = {Fachanwaltskommentar Insolvenzrecht / hrsg. von Martin Ahrens; Markus Gehrlein; Andreas Ringstmeier . - 2. Aufl.}, publisher = {Luchterhand}, address = {K{\"o}ln}, isbn = {978-3-472-08559-1}, pages = {1317 -- 1356}, year = {2014}, language = {de} } @article{LindEllrich2014, author = {Lind, Thorsten Patric and Ellrich, Thomas}, title = {Zur Haftung der Gl{\"a}ubigerausschussmitglieder wegen unzureichender Kassenpr{\"u}fung}, series = {Der Betrieb}, volume = {67}, journal = {Der Betrieb}, number = {49}, publisher = {Fachmedien Otto Schmidt}, address = {D{\"u}sseldorf}, issn = {0005-9935}, pages = {2819 -- 2820}, year = {2014}, language = {de} } @article{GellertButenweg2014, author = {Gellert, Christoph and Butenweg, Christoph}, title = {Seismic analysis of masonry structures in German earthquake zones according to DIN EN 1998-1}, series = {Mauerwerk : European journal of masonry}, volume = {18}, journal = {Mauerwerk : European journal of masonry}, number = {3-4}, publisher = {Ernst \& Sohn}, address = {Berlin}, issn = {1437-1022 (E-Journal); 1432-3427 (Print)}, doi = {10.1002/dama.201400626}, pages = {188 -- 196}, year = {2014}, abstract = {Die Erdbeben in Albstadt 1978 (Magnitude 5,7), Roermond 1992 (Magnitude 5,9) oder in Waldkirch 2004 (Magnitude 5,1) haben verdeutlicht, dass die erdbebensichere Auslegung von Mauerwerksbauten auch in Deutschland von großer Bedeutung ist. Bereits im Jahr 1981 wurde die DIN 4149 (1981) "Bauten in deutschen Erdbebengebieten - Lastannahmen, Bemessung und Ausf{\"u}hrung {\"u}blicher Hochbauten" eingef{\"u}hrt, in der aber f{\"u}r Mauerwerksbauten nur wenige Anforderungen gestellt wurden. Diese Norm wurde durch den NABau-Arbeitsausschuss "Erdbeben; Sonderfragen" des Deutschen Instituts f{\"u}r Normung e.V. (DIN) auf Grundlage des Eurocode 8 (2004) vollst{\"a}ndig {\"u}berarbeitet und durch die DIN 4149 (2005) abgel{\"o}st, die umfangreiche Regelungen f{\"u}r die seismische Auslegung von Mauerwerksbauten enth{\"a}lt. Mittlerweile liegen die DIN EN 1998-1 (2010) und der Nationale Anhang DIN EN 1998-1/NA (2011) vor, die nach Einarbeitung der Ergebnisse der durchgef{\"u}hrten Anwendungserprobung bauaufsichtlich eingef{\"u}hrt und die DIN 4149 (2005) ersetzen werden. Der folgende Beitrag gibt einen {\"U}berblick {\"u}ber die seismische Berechnung und Bemessung von Mauerwerksbauten nach dem europ{\"a}ischen Regelwerk und illustriert deren Anwendung an einem baupraktischen Beispiel.}, language = {de} } @article{ButenwegMeyerFehling2014, author = {Butenweg, Christoph and Meyer, Udo and Fehling, Ekkehard}, title = {EU-Projekt INSYSME: Innovative Techniken f{\"u}r erdbebensichere Ausfachungsw{\"a}nde aus Ziegelmauerwerk in Stahlbetonrahmentragwerken}, series = {Mauerwerk : European journal of masonry}, volume = {18}, journal = {Mauerwerk : European journal of masonry}, number = {2}, publisher = {Ernst \& Sohn}, address = {Berlin}, issn = {1437-1022 (E-Journal); 1432-3427 (Print)}, doi = {10.1002/dama.201400612}, pages = {78 -- 81}, year = {2014}, abstract = {Am 1. Oktober 2013 ist das auf drei Jahre angelegte EU-Forschungsprojekt INSYSME - Innovative Systeme f{\"u}r erdbebentaugliche Ausfachungsw{\"a}nde aus Ziegelmauerwerk in Stahlbetonrahmentragwerken - gestartet. Unter der Koordination der Universit{\"a}t Padua beteiligen sich 16 Partner aus sechs europ{\"a}ischen L{\"a}ndern (Deutschland, Griechenland, Italien, Portugal, Rum{\"a}nien, T{\"u}rkei). Als deutsche Partner nehmen die Arbeitsgemeinschaft Mauerziegel aus Bonn, die Universit{\"a}t Kassel sowie das Ingenieurb{\"u}ro SDA-engineering GmbH aus Herzogenrath, teil. Ziel der deutschen Partner ist die Entwicklung von innovativen Ausfachungssystemen aus monolithischem w{\"a}rmed{\"a}mmenden Ziegelmauerwerk, mit denen nicht nur eine erh{\"o}hte Erdbebensicherheit, sondern auch die sichere Erf{\"u}llung der steigenden Anforderungen aus Windbeanspruchungen gew{\"a}hrleistet werden k{\"o}nnen. Die Forschungsergebnisse sollen vom Partner SDA-engineering GmbH in die bereits seit einigen Jahren verf{\"u}gbare Softwarel{\"o}sung MINEA [1] integriert werden. Weitere Informationen stehen auf den Websites des Projektes [2] zur Verf{\"u}gung. Im vorliegenden Beitrag werden nach einer kurzen thematischen Einf{\"u}hrung die Ergebnisse von Tastversuchen an senkrecht zur Ebene belasteten Ausfachungsw{\"a}nden aus Planziegelmauerwerk vorgestellt. Im Anschluss wird das geplante Arbeitsprogramm der deutschen Partner im Projekt INSYSME beschrieben.}, language = {de} } @article{ButenwegSchmittRosen2014, author = {Butenweg, Christoph and Schmitt, Timo and Rosen, Britta}, title = {Seismische Einwirkungen auf erdverlegte Rohrleitungssysteme}, series = {Bauingenieur : die richtungsweisende Zeitschrift im Bauingenieurswesen ; offizielle Zeitschrift der VDI-Gesellschaft Bautechnik}, volume = {89 (2014)}, journal = {Bauingenieur : die richtungsweisende Zeitschrift im Bauingenieurswesen ; offizielle Zeitschrift der VDI-Gesellschaft Bautechnik}, number = {Heft 7/8}, publisher = {VDI Fachmedien}, address = {D{\"u}sseldorf}, issn = {0005-6650}, pages = {316 -- 324}, year = {2014}, language = {de} } @inproceedings{ButenwegHoltschoppen2014, author = {Butenweg, Christoph and Holtschoppen, Britta}, title = {Seismic design of industrial facilities in Germany}, series = {Seismic Design of Industrial Facilities : proceedings of the International Conference on Seismic Design of Industrial Facilities (SeDIF-Conference) : Aachen, 26. - 27.9.2013}, booktitle = {Seismic Design of Industrial Facilities : proceedings of the International Conference on Seismic Design of Industrial Facilities (SeDIF-Conference) : Aachen, 26. - 27.9.2013}, publisher = {Springer Vieweg}, address = {Wiesbaden}, isbn = {978-3-658-02809-1 ; 3-658-02809-2 (Print) ; 978-3-658-02810-7 (E-Book)}, doi = {10.1007/978-3-658-02810-7_6}, pages = {63 -- 74}, year = {2014}, language = {de} } @incollection{ButenwegNorda2014, author = {Butenweg, Christoph and Norda, H.}, title = {Erdbebenberechnung von Mauerwerksbauten nach DIN EN 1998-1:2010-12}, series = {Mauerwerksbau-Praxis nach Eurocode / Schubert, Schneider, Schoch (Hrsg.). - 3., vollst{\"a}ndig {\"u}berarbeitete Auflage}, booktitle = {Mauerwerksbau-Praxis nach Eurocode / Schubert, Schneider, Schoch (Hrsg.). - 3., vollst{\"a}ndig {\"u}berarbeitete Auflage}, publisher = {Beuth}, address = {Berlin, Wien, Z{\"u}rich}, isbn = {978-3-410-22739-7}, pages = {367 -- 412}, year = {2014}, language = {de} } @incollection{AltayTaddeiButenwegetal.2014, author = {Altay, Okyay and Taddei, Francesca and Butenweg, Christoph and Klinkel, Sven}, title = {Vibration mitigation of wind turbine towers with tuned mass dampers}, series = {Wind turbine control and monitoring. (Advances in industrial control)}, booktitle = {Wind turbine control and monitoring. (Advances in industrial control)}, publisher = {Springer}, address = {Cham ; Heidelberg ; New York ; Dordrecht ; London}, isbn = {978-3-319-08412-1 (Print) ; 978-3-319-08413-8 (E-Book)}, doi = {10.1007/978-3-319-08413-8_12}, pages = {337 -- 373}, year = {2014}, abstract = {Because of its minor environmental impact, electricity generation using wind power is getting remarkable. The further growth of the wind industry depends on technological solutions to the challenges in production and construction of the turbines. Wind turbine tower vibrations, which limit power generation efficiency and cause fatigue problems with high maintenance costs, count as one of the main structural difficulties in the wind energy sector. To mitigate tower vibrations auxiliary measures are necessary. The effectiveness of tuned mass damper is verified by means of a numeric study on a 5 MW onshore reference wind turbine. Hereby, also seismic-induced vibrations and soil-structure interaction are considered. Acquired results show that tuned mass damper can effectively reduce resonant tower vibrations and improve the fatigue life of wind turbines. This chapter is also concerned with tuned liquid column damper and a semiactive application of it. Due to its geometric versatility and low prime costs, tuned liquid column dampers are a good alternative to other damping measures, in particular for slender structures like wind turbines.}, language = {en} } @book{KlinkelButenwegLinetal.2014, author = {Klinkel, Sven and Butenweg, Christoph and Lin, Gao and Holtschoppen, Britta}, title = {Seismic design of industrial facilities : Proceedings of the International Conference on Seismic Design of Industrial Facilities (SeDIF) / Sven Klinkel, Christoph Butenweg, Gao Lin, Britta Holtschoppen Editors}, publisher = {Springer Vieweg}, address = {Wiesbaden}, organization = {International Conference on Seismic Design of Industrial Facilities }, isbn = {978-3-658-02809-1 (Print) ; 978-365-80281-0-7 (E-Book)}, doi = {10.1007/978-3-658-02810-7}, pages = {XIII, 450 S.}, year = {2014}, language = {en} } @techreport{ButenwegKaiser2014, author = {Butenweg, Christoph and Kaiser, Diethelm}, title = {Seismic hazard harmonisation in Europe (SHARE) : DGEB-Workshop in Frankfurt a.M., Germany, 27. May 2014 / Christoph Butenweg, Diethelm Kaiser (editors)}, publisher = {DGEB}, address = {Aachen}, organization = {Deutsche Gesellschaft f{\"u}r Erdbeben-Ingenieurwesen und Baudynamik}, isbn = {3-930108-12-7}, pages = {V, 117 S.}, year = {2014}, language = {en} } @inproceedings{FuchsRitz2014, author = {Fuchs, Britta and Ritz, Thomas}, title = {Usability for Blended Shopping - Solving Major Flaws by Applying Usability Engineering and Proven Integration Technologies}, series = {Proceedings of the 11th International Conference on e-Business, ICE-B 2014, Vienna, Austria}, booktitle = {Proceedings of the 11th International Conference on e-Business, ICE-B 2014, Vienna, Austria}, isbn = {978-989-758-043-7}, doi = {10.5220/0005113502160223}, pages = {216 -- 223}, year = {2014}, language = {en} } @article{MeyerButenwegFehling2014, author = {Meyer, Udo and Butenweg, Christoph and Fehling, Ekkehard}, title = {EU-Projekt INSYSME : innovative Systeme f{\"u}r erdbebentaugliche Ausfachungsw{\"a}nde aus Ziegelmauerwerk}, series = {Bauingenieur : die richtungsweisende Zeitschrift im Bauingenieurswesen ; offizielle Zeitschrift der VDI-Gesellschaft Bautechnik. Beilage: D-A-CH-Mitteilungsblatt}, volume = {89 (2014)}, journal = {Bauingenieur : die richtungsweisende Zeitschrift im Bauingenieurswesen ; offizielle Zeitschrift der VDI-Gesellschaft Bautechnik. Beilage: D-A-CH-Mitteilungsblatt}, number = {April}, publisher = {VDI Fachmedien}, address = {D{\"u}sseldorf}, issn = {1436-4867 (E-Journal); 0005-6650 (Print)}, pages = {S14 -- S15}, year = {2014}, language = {de} } @article{ButenwegRenault2014, author = {Butenweg, Christoph and Renault, Philippe}, title = {Workshop der Gesellschaften zum EU-Projekt SHARE}, series = {Bauingenieur : die richtungsweisende Zeitschrift im Bauingenieurswesen ; offizielle Zeitschrift der VDI-Gesellschaft Bautechnik. Beilage: D-A-CH-Mitteilungsblatt}, volume = {89 (2014)}, journal = {Bauingenieur : die richtungsweisende Zeitschrift im Bauingenieurswesen ; offizielle Zeitschrift der VDI-Gesellschaft Bautechnik. Beilage: D-A-CH-Mitteilungsblatt}, number = {Oktober}, publisher = {VDI Fachmedien}, address = {D{\"u}sseldorf}, issn = {1436-4867 (E-Journal); 0005-6650 (Print)}, pages = {S2 -- S3}, year = {2014}, language = {de} } @inproceedings{EdipGarevskiButenwegetal.2014, author = {Edip, Kemal and Garevski, Mihail and Butenweg, Christoph and Sheshov, Vlatko and Bojadjieva, Julijana and Gjorgjiev, Igor}, title = {New coupled finite-infinite element approach for wave propagation simulation of unbounded soil media}, series = {2nd European Conference on Earthquake Engineering and Seismology 2014 (2nd ECEES) : joint event of the 15th European Conference on Earthquake Engineering and the 34th General Assembly of the European Seismological Commission : Istanbul, Turkey, 25-29 August 2014 / European Association for Earthquake Engineering (EAEE) ; Vol. 2}, booktitle = {2nd European Conference on Earthquake Engineering and Seismology 2014 (2nd ECEES) : joint event of the 15th European Conference on Earthquake Engineering and the 34th General Assembly of the European Seismological Commission : Istanbul, Turkey, 25-29 August 2014 / European Association for Earthquake Engineering (EAEE) ; Vol. 2}, publisher = {Curran Associates, Inc.}, address = {Red Hook, NY}, organization = {European Conference on Earthquake Engineering and Seismology <2, 2014, Istanbul>}, isbn = {978-1-5108-1021-1}, pages = {1556 -- 1561}, year = {2014}, language = {en} } @inproceedings{RosinButenweg2014, author = {Rosin, Julia and Butenweg, Christoph}, title = {Berechnungsansatz f{\"u}r basisisolierte Tankbauwerke}, series = {Berichte der Fachtagung Baustatik - Baupraxis 12 am 24. und 25. Februar 2014 an der Technischen Universit{\"a}t M{\"u}nchen / Hrsg. Kai-Uwe Bletzinger ...}, booktitle = {Berichte der Fachtagung Baustatik - Baupraxis 12 am 24. und 25. Februar 2014 an der Technischen Universit{\"a}t M{\"u}nchen / Hrsg. Kai-Uwe Bletzinger ...}, publisher = {Lehrstuhl f{\"u}r Statik, Techn. Univ. M{\"u}nchen}, address = {M{\"u}nchen}, organization = {Fachtagung Baustatik - Baupraxis <12, 2014, M{\"u}nchen>}, isbn = {978-3-00-041256-1}, pages = {103 -- 112}, year = {2014}, language = {de} } @inproceedings{AltayKlinkelButenweg2014, author = {Altay, Okyay and Klinkel, Sven and Butenweg, Christoph}, title = {Intelligente semiaktive D{\"a}mpfungssysteme zur Reduktion periodischer und stochastischer Bauwerksschwingungen}, series = {Berichte der Fachtagung Baustatik - Baupraxis 12 am 24. und 25. Februar 2014 an der Technischen Universit{\"a}t M{\"u}nchen / Hrsg. Kai-Uwe Bletzinger ...}, booktitle = {Berichte der Fachtagung Baustatik - Baupraxis 12 am 24. und 25. Februar 2014 an der Technischen Universit{\"a}t M{\"u}nchen / Hrsg. Kai-Uwe Bletzinger ...}, publisher = {Lehrstuhl f{\"u}r Statik, Techn. Univ. M{\"u}nchen}, address = {M{\"u}nchen}, organization = {Fachtagung Baustatik - Baupraxis <12, 2014, M{\"u}nchen>}, isbn = {978-3-00-041256-1}, pages = {397 -- 404}, year = {2014}, language = {de} } @inproceedings{AltayButenwegKlinkeletal.2014, author = {Altay, Okyay and Butenweg, Christoph and Klinkel, Sven and Taddei, Francesca}, title = {Vibration mitigation of wind turbine towers by tuned liquid column dampers}, series = {Proceedings of the 9th European Conference on Structural Dynamics, EURODYN 2014 Porto, Portugal, 30 June - 2 July 2014 / A. Cunha, E. Caetano, .... (eds.)}, booktitle = {Proceedings of the 9th European Conference on Structural Dynamics, EURODYN 2014 Porto, Portugal, 30 June - 2 July 2014 / A. Cunha, E. Caetano, .... (eds.)}, address = {Porto}, organization = {European Conference on Structural Dynamics, EURODYN <9, 2014, Porto>}, isbn = {978-972-752-165-4}, pages = {1531 -- 1538}, year = {2014}, language = {en} } @article{VerschitzButenweg2014, author = {Verschitz, Daniel and Butenweg, Christoph}, title = {Standsicherheitsnachweis von Beh{\"a}ltern f{\"u}r Kleinkl{\"a}ranlagen}, series = {ACWA aktuell}, journal = {ACWA aktuell}, number = {12 - 9/2014}, publisher = {RWTH Aachen}, address = {Aachen}, pages = {10}, year = {2014}, abstract = {Die PIA GmbH pr{\"u}ft seit fast 8 Jahren die Standsicherheit von Beh{\"a}ltern f{\"u}r Kleinkl{\"a}ranlagen. Diese bestehen in der Regel aus Kunststoff oder Beton und m{\"u}ssen {\"u}ber ihre gesamte Lebensdauer den Beanspruchungen aus Handhabung, Einbau und Betrieb standhalten. Die Standsicherheit kann nach EN 12566 wahlweise durch einen rechnerischen Nachweis oder durch einen praktischen Nachweis wie die Bruchlastpr{\"u}fung oder die Pr{\"u}fung in der Grube erfolgen.}, language = {de} } @inproceedings{DalguerChurilovButenwegetal.2014, author = {Dalguer, Luis A. and Churilov, Sergey and Butenweg, Christoph and Renault, Philippe and Hyun, An Jun}, title = {Dynamic analysis of a reinforced concrete electrical nuclear building of SMART 2013 project subjected to earthquake excitation using ABAQUS}, series = {Workshop SMART2013 : Paris, France, November 25th - 27th, 2014}, booktitle = {Workshop SMART2013 : Paris, France, November 25th - 27th, 2014}, organization = {Workshop SMART2013 <2014, Paris>}, pages = {1 -- 12}, year = {2014}, language = {en} } @inproceedings{HecklWeilerFleischhakeretal.2014, author = {Heckl, O. H. and Weiler, Sascha and Fleischhaker, Robert and Gebs, Raphael and Budnicki, Aleksander and Wolf, M. and Kleinbauer, Jochen and Russ, S. and Kumkar, M. and Sutter, Dirk H.}, title = {Industry-grade high average power femtosecond light source}, series = {Frontiers in ultrafast optics: Biomedical, scientific, and industrial applications XIV : 1 Februar 2014, San Francisco, USA. - (SPIE proceedings series ; 8972)}, booktitle = {Frontiers in ultrafast optics: Biomedical, scientific, and industrial applications XIV : 1 Februar 2014, San Francisco, USA. - (SPIE proceedings series ; 8972)}, editor = {Heisterkamp, Alexander and Herman, Peter R. and Meunier, Michael and Nolte, Stefan}, publisher = {SPIE, International Society for Optical Engineering}, doi = {10.1117/12.2039337}, pages = {89720P -- 89720P-7}, year = {2014}, language = {en} } @inproceedings{RosinKubalskiButenweg2014, author = {Rosin, Julia and Kubalski, Thomas and Butenweg, Christoph}, title = {Seismic Design of cylindrical liquid storage tanks}, series = {Seismic design of industrial facilities : proceedings of the International Conference on Seismic Design of Industrial Facilities (SeDIF-Conference) ; [Aachen, 26. - 27. September 2013] / Chair of Structural Statics and Dynamics, RWTH Aachen. Sven Klinkel ..., ed.}, booktitle = {Seismic design of industrial facilities : proceedings of the International Conference on Seismic Design of Industrial Facilities (SeDIF-Conference) ; [Aachen, 26. - 27. September 2013] / Chair of Structural Statics and Dynamics, RWTH Aachen. Sven Klinkel ..., ed.}, publisher = {Springer Vieweg}, address = {Wiesbaden}, organization = {International Conference on Seismic Design of Industrial Facilities <2013, Aachen>}, isbn = {978-3-658-02810-7 (E-Book) ; 978-3-658-02809-1 (Print)}, doi = {10.1007/978-3-658-02810-7_36}, pages = {429 -- 440}, year = {2014}, language = {en} } @inproceedings{EdipGarevskiButenwegetal.2014, author = {Edip, Kemal and Garevski, Mihail and Butenweg, Christoph and Sesov, Vlatko and Bojadjieva, Julijana and Gjorgjiev, Igor}, title = {Boundary effects on seismic analysis of multi-storey frames considering soil structure interaction phenomenon}, series = {Seismic design of industrial facilities : proceedings of the International Conference on Seismic Design of Industrial Facilities (SeDIF-Conference) ; [Aachen, 26. - 27. September 2013] / Chair of Structural Statics and Dynamics, RWTH Aachen. Sven Klinkel ..., ed}, booktitle = {Seismic design of industrial facilities : proceedings of the International Conference on Seismic Design of Industrial Facilities (SeDIF-Conference) ; [Aachen, 26. - 27. September 2013] / Chair of Structural Statics and Dynamics, RWTH Aachen. Sven Klinkel ..., ed}, publisher = {Springer Vieweg}, address = {Wiesbaden}, organization = {International Conference on Seismic Design of Industrial Facilities <2013, Aachen>}, isbn = {978-3-658-02809-1 (Print) ; 978-3-658-02810-7}, doi = {10.1007/978-3-658-02810-7_47}, pages = {569 -- 576}, year = {2014}, language = {en} } @inproceedings{GiresiniButenwegAndreinietal.2014, author = {Giresini, Linda and Butenweg, Christoph and Andreini, M. and De Falco, A. and Sassu, M.}, title = {Numerical calibration of a macro-element for vaultes system in historic churches}, series = {9th International Conference on Structural Analyses of Historical Conctruction, 14 - 17 October, 2014, Mexico City}, booktitle = {9th International Conference on Structural Analyses of Historical Conctruction, 14 - 17 October, 2014, Mexico City}, organization = {International Conference on Structural Analyses of Historical Conctructions <9, 2014, Mexico City>}, pages = {1 -- 12}, year = {2014}, language = {en} } @inproceedings{GiresiniButenwegAndreinietal.2014, author = {Giresini, Linda and Butenweg, Christoph and Andreini, M. and De Falco, A. and Sassu, M.}, title = {Macro-elements identification in historic chapels: the case of St. Venerio Chapel in Reggiolo - Emilia Romagna}, series = {9th International Conference on Structural Analyses of Historical Conctruction, 14 - 17 October, 2014, Mexico City}, booktitle = {9th International Conference on Structural Analyses of Historical Conctruction, 14 - 17 October, 2014, Mexico City}, organization = {International Conference on Structural Analyses of Historical Conctructions <9, 2014, Mexico City>}, pages = {1 -- 12}, year = {2014}, language = {en} } @incollection{ButenwegKlinkel2014, author = {Butenweg, Christoph and Klinkel, Sven}, title = {Dynamisches Verhalten von Stahlbetonplatten unter Impact-Belastungen}, series = {Massivbau im Wandel : Festschrift zum 60. Geburtstag von Josef Hegger}, booktitle = {Massivbau im Wandel : Festschrift zum 60. Geburtstag von Josef Hegger}, publisher = {Ernst}, address = {Berlin}, isbn = {3-939051-20-9}, pages = {369 -- 380}, year = {2014}, language = {de} } @inproceedings{RosinButenweg2014, author = {Rosin, Julia and Butenweg, Christoph}, title = {Seismic isolation of cylindrical liquid storage tanks}, series = {Proceedings of the 9th European Conference on Structural Dynamics, EURODYN 2014 Porto, Portugal, 30 June - 2 July 2014 / A. Cunha, E. Caetano, .... (eds.)}, booktitle = {Proceedings of the 9th European Conference on Structural Dynamics, EURODYN 2014 Porto, Portugal, 30 June - 2 July 2014 / A. Cunha, E. Caetano, .... (eds.)}, address = {Porto}, organization = {European Conference on Structural Dynamics, EURODYN <9, 2014, Porto>}, isbn = {978-972-752-165-4}, pages = {3145 -- 3152}, year = {2014}, language = {en} } @inproceedings{RosinHenneboehlButenweg2014, author = {Rosin, Julia and Henneb{\"o}hl, Benedickt and Butenweg, Christoph}, title = {Global buckling analysis of cylindrical liquid storage tanks under earthquake loading}, series = {2nd European Conference on Earthquake Engineering and Seismology 2014 (2nd ECEES) : joint event of the 15th European Conference on Earthquake Engineering and the 34th General Assembly of the European Seismological Commission : Istanbul, Turkey, 25-29 August 2014 / European Association for Earthquake Engineering (EAEE) ; Vol. 6}, booktitle = {2nd European Conference on Earthquake Engineering and Seismology 2014 (2nd ECEES) : joint event of the 15th European Conference on Earthquake Engineering and the 34th General Assembly of the European Seismological Commission : Istanbul, Turkey, 25-29 August 2014 / European Association for Earthquake Engineering (EAEE) ; Vol. 6}, publisher = {Curran Associates, Inc.}, address = {Red Hook, NY}, organization = {European Conference on Earthquake Engineering and Seismology <2, 2014, Istanbul>}, isbn = {978-1-5108-1021-1}, pages = {5270 -- 5281}, year = {2014}, language = {en} } @misc{OPUS4-7866, title = {Dimensionen 1-2014 : Magazin der FH Aachen University of Applied Sciences}, address = {Aachen}, organization = {Aachen / Fachhochschule Aachen}, pages = {96}, year = {2014}, abstract = {Thema 06 Im Steinreich | Wie Dombaumeister und FH-Absolvent Helmut Maintz mit modernen Mitteln das Erbe von 1200 Jahren bewahrt 12 Ein Meer aus Purpur und Gold | Karlsfiguren als Botschafter Aachens 14 Karl ist in uns allen! | Fotoshooting auf dem M{\"u}nsterplatz war ein Riesenerfolg Studium 16 Made in Goethestraße | Studierende arbeiten an der Weiterentwicklung von 3-D-Druckern 18 Wenn Tr{\"a}ume fliegen lernen | Fachbereich Luft- und Raumfahrttechnik bietet Summerschool Segelfliegen an 20 Kampf um die goldene Dose | Robotikwettbewerb f{\"u}r Scientific-Programming-Studierende 21 R{\"u}ckenschmerz war gestern | FH-Team entwickelt eine Auflage f{\"u}r B{\"u}rost{\"u}hle 22 Auf gute Nachbarschaft | FH kooperiert mit niederl{\"a}ndischem Studierendenverein 24 Vier Unternehmen, drei Tage und 1000 Eindr{\"u}cke | Studierende des Fachbereichs Wirtschaftswissenschaften auf Benchmark-Reise 25 Ein Grill ist keine Lampe | Gestalter gewinnen Publikumspreis beim Young Creations Award: Upcycling 2014 26 Eine Aufgabe f{\"u}r die gesamte Hochschule | Halbzeitbilanz f{\"u}r das Projekt zur Qualit{\"a}tsverbesserung in Studium und Lehre 27 Kreative Zuf{\"a}lle | Siebdruckkurs im Ludwig Forum 28 Meldungen/Studium International 30 Goldrausch | Zehn Studierende des Fachbereichs Bauingenieurwesen fahren auf Exkursion nach Kalifornien 32 Torbens Triple | Student des Fachbereichs Wirtschaftswissenschaften auf der Erfolgsspur 34 Auf einmal mittendrin | Studierende des Fachbereichs Gestaltung erleben Istanbul 36 Wenn Tiger am Tatort schwitzen | Zwei FH-Studentinnen forschen f{\"u}r ein paar Monate in der weiten Welt FORSCHUNG UND TRANSFER 38 Der IceMole wird erwachsen | Einschmelzsonde besteht H{\"a}rtetest in der Antarktis 40 Z{\"u}ndkerze | Mit Mikrowellenenergie Sprit sparen 42 Eine Aufgabe f{\"u}r eine ganze Generation | Energiewende ist und bleibt zentrales Thema des Solar-Instituts J{\"u}lich 44 „Early Birds" - Premiere in Belgien | Vertreter aus Wirtschaft und Wissenschaft zu Gast bei der Sterisys PGmbH 46 Eine elektronische Nase | FH-Forscher entwickelt neues Verfahren zur {\"U}berwachung von Abf{\"u}llprozessen 48 Ein H{\"o}henflug | Motorsegler der FH Aachen {\"u}berfliegt den Himalaya bis hinauf zum Gipfel des Mount Everest Personen 52 Unser Mann auf dem Himalaya | Fabian Nawrath hat schon in vielen L{\"a}ndern eine Dose Cola getrunken 58 Ein Mythos lebt | FH-Alumnus Uwe Niermann und K{\"u}nstler Peter Klasen bringen Rennlegende wieder auf die Strecke 62 Noch mehr Fahrspaß am Dreil{\"a}ndereck | FH-Student Ren{\´e} Hamacher engagiert sich f{\"u}rs Mountainbiken 63 Boonzaaijer begeistert | FH Aachen verleiht Lehrpreis an Designprofessor 64 Mein Partner mit der kalten Schnauze | Tierische Verst{\"a}rkung in der Telefonzentrale der FH Aachen 68 Alles andere als langweilig | Leif Battermann ist einer von 78 Studierenden, die eine Ehrenplakette erhalten 70 R{\"u}ckenwind f{\"u}rs Studium | 70 Studierende erhalten ein FH-Stipendium 72 Von Kaiser Wilhelm bis Buffalo Bill | Thomas Lochner erz{\"a}hlt die Geschichte der Aachener Tuchindustrie 73 Personalia / Professoren 76 Neue Gleichstellungsbeauftragte | Judith K{\"u}rten l{\"o}st Andrea St{\"u}hn ab 76 im Amt best{\"a}tigt | Prof. Klocke steht auch in der neuen Amtsperiode an der Spitze des Hochschulrats der FH Kiel SERVICE 78 Den Boden bereiten | Der neue Campus der FH Aachen an der Eupener Straße nimmt Gestalt an 80 Herzlich willkommen! | Fotoaktion bei den Newcomer Days 82 Neuer H{\"o}rsaal auf dem Campus J{\"u}lich | Nach nur sieben Monaten Bauzeit fertiggestellt 83 Alle Ampeln auf Gr{\"u}n | Sch{\"u}lerinnen bauen Auto mit Wasserstoffantrieb 84 Gemeinsam f{\"u}r den Wissenschaftsstandort | Region und Hochschulen unterzeichnen Kooperationsvertrag 86 Messen und Veranstaltungen 93 Meldungen/Service 94 Ortswechsel | Macht Kunst Sch{\"a}tze - die Ausstellungen zum Karlsjahr 96 Impressum}, language = {de} } @misc{OPUS4-7867, title = {Dimensionen 2-2014 : Magazin der FH Aachen University of Applied Sciences}, address = {Aachen}, organization = {Aachen / Fachhochschule Aachen}, pages = {64}, year = {2014}, abstract = {Thema 06 On the Road and Inside Indonesia | FH-Studentin Petra Hess schreibt ein Buch {\"u}ber Sulawesi 12 Von Hunden im Schafskost{\"u}m | Mit „North Orbit" zeigt der Student Kevin Ramolla Island einmal anders Studium 16 Intelligenter als Staubsaugerroboter | Robotik an der FH Aachen 18 Wir sind Weltmeister! | Carologistics-Team gewinnt bei Roboter-WM 20 „Dein Passwort h{\"a}lt 28 Trilliarden Jahre lang durch!" | Studierende sch{\"a}rfen Bewusstsein f{\"u}r Passwortsicherheit 22 Gute Ideen f{\"u}r echte Herausforderungen | Zukunftswerkstatt bei der Summer School Renewable Energy 24 Auf der {\"U}berholspur | Aixtreme-Racing-Team blickt auf eine gute Saison 26 Das „Momentum" halten | Interview mit Teamchef Maximilian Philippi 28 Statt Fernseher und Fitnessstudio | Help e.V. hilft jungen Menschen, sich sozial zu engagieren 30 Nimm mein Auto! | FH-Student arbeitet im Start-up-Unternehmen „Tamyca" 32 Nominiert: PR-Bild-Award 34 Den Nerv der Zeit getroffen | Studenten gewinnen dritten Platz bei weltweitem Wettbewerb International 36 Kleiner Sprung, großer Sprung | Solange Wetzels hat sich f{\"u}r ein Studium an der FH entschieden FORSCHUNG UND TRANSFER 38 Schlag auf Schlag | Pulsierende Herzzellen ebnen im Institut f{\"u}r Bioengineering den Weg zur personalisierten Medizin 42 Komplexe Prozesse einfach dargestellt | Gestalterteam entwirft iPad-App f{\"u}r „ProSense" 44 Zwei Welten vereint | Bei der Entwicklung von Sensoren verkn{\"u}pft das Institut f{\"u}r Nano- und Biotechnologien Biologie und Mikroelektronik Personen 48 Wir machen euch zum Kaiser! | Fotoaktion bei den Newcomer Days 50 An der Schnittstelle | Dr. Nils Bausch arbeitet als Lecturer an der University of Portsmouth 55 Zwei neue Publikationen zum Aachener Dom SERVICE 56 Meldungen 59 Kopfnuss 60 Ortswechsel | „La Batte" in L{\"u}ttich 62 Impressum}, language = {de} } @article{HaagZontarSchleupenetal.2014, author = {Haag, S. and Zontar, D. and Schleupen, Josef and M{\"u}ller, T. and Brecher, C.}, title = {Chain of refined perception in self-optimizing assembly of micro-optical systems}, series = {Journal of sensors and sensor systems}, volume = {3}, journal = {Journal of sensors and sensor systems}, number = {1}, publisher = {Copernicus Publ.}, address = {G{\"o}ttingen}, issn = {2194-878X}, doi = {10.5194/jsss-3-87-2014}, pages = {87 -- 95}, year = {2014}, abstract = {Today, the assembly of laser systems requires a large share of manual operations due to its complexity regarding the optimal alignment of optics. Although the feasibility of automated alignment of laser optics has been shown in research labs, the development effort for the automation of assembly does not meet economic requirements - especially for low-volume laser production. This paper presents a model-based and sensor-integrated assembly execution approach for flexible assembly cells consisting of a macro-positioner covering a large workspace and a compact micromanipulator with camera attached to the positioner. In order to make full use of available models from computer-aided design (CAD) and optical simulation, sensor systems at different levels of accuracy are used for matching perceived information with model data. This approach is named "chain of refined perception", and it allows for automated planning of complex assembly tasks along all major phases of assembly such as collision-free path planning, part feeding, and active and passive alignment. The focus of the paper is put on the in-process image-based metrology and information extraction used for identifying and calibrating local coordinate systems as well as the exploitation of that information for a part feeding process for micro-optics. Results will be presented regarding the processes of automated calibration of the robot camera as well as the local coordinate systems of part feeding area and robot base.}, language = {en} } @inproceedings{GoettscheRoether2014, author = {G{\"o}ttsche, Joachim and R{\"o}ther, Sascha}, title = {Science College Overbach - Innovatives Bildungszentrum in J{\"u}lich-Barmen}, series = {18. Internationale Passivhaustagung, Aachen, April 2014}, booktitle = {18. Internationale Passivhaustagung, Aachen, April 2014}, pages = {6 Seiten}, year = {2014}, abstract = {Preprint der Autoren}, language = {de} } @article{VosLagemaatBarentszetal.2014, author = {Vos, E. K. and Lagemaat, M. W. and Barentsz, J. O. and F{\"u}tterer, J. J. and Zamecnik, P. and Roozen, H. and Orzada, S. and Bitz, Andreas and Maas, M. C. and Scheenen, T. W. J.}, title = {Image quality and cancer visibility of T2-weighted Magnetic Resonance Imaging of the prostate at 7 Tesla}, series = {European Radiology}, volume = {24}, journal = {European Radiology}, number = {8}, publisher = {Springer}, address = {Cham}, issn = {1432-1084}, doi = {10.1007/s00330-014-3234-6}, pages = {1950 -- 1958}, year = {2014}, abstract = {Objectives To assess the image quality of T2-weighted (T2w) magnetic resonance imaging of the prostate and the visibility of prostate cancer at 7 Tesla (T). Materials \& methods Seventeen prostate cancer patients underwent T2w imaging at 7T with only an external transmit/receive array coil. Three radiologists independently scored images for image quality, visibility of anatomical structures, and presence of artefacts. Krippendorff's alpha and weighted kappa statistics were used to assess inter-observer agreement. Visibility of prostate cancer lesions was assessed by directly linking the T2w images to the confirmed location of prostate cancer on histopathology. Results T2w imaging at 7T was achievable with 'satisfactory' (3/5) to 'good' (4/5) quality. Visibility of anatomical structures was predominantly scored as 'satisfactory' (3/5) and 'good' (4/5). If artefacts were present, they were mostly motion artefacts and, to a lesser extent, aliasing artefacts and noise. Krippendorff's analysis revealed an α = 0.44 between three readers for the overall image quality scores. Clinically significant cancer lesions in both peripheral zone and transition zone were visible at 7T. Conclusion T2w imaging with satisfactory to good quality can be routinely acquired, and cancer lesions were visible in patients with prostate cancer at 7T using only an external transmit/receive body array coil.}, language = {en} } @article{TheysohnKraffEilersetal.2014, author = {Theysohn, Jens M. and Kraff, Oliver and Eilers, Kristina and Andrade, Dorian and Gerwig, Marcus and Timmann, Dagmar and Schmitt, Franz and Ladd, Mark E. and Ladd, Susanne C. and Bitz, Andreas}, title = {Vestibular effects of a 7 Tesla MRI examination compared to 1.5 T and 0 T in healthy volunteers}, series = {PLoS one}, volume = {9}, journal = {PLoS one}, number = {3}, publisher = {PLOS}, address = {San Francisco}, issn = {1932-6203}, doi = {10.1371/journal.pone.0092104}, year = {2014}, abstract = {Ultra-high-field MRI (7 Tesla (T) and above) elicits more temporary side-effects compared to 1.5 T and 3 T, e.g. dizziness or "postural instability" even after exiting the scanner. The current study aims to assess quantitatively vestibular performance before and after exposure to different MRI scenarios at 7 T, 1.5 T and 0 T. Sway path and body axis rotation (Unterberger's stepping test) were quantitatively recorded in a total of 46 volunteers before, 2 minutes after, and 15 minutes after different exposure scenarios: 7 T head MRI (n = 27), 7 T no RF (n = 22), 7 T only B₀ (n = 20), 7 T in \& out B₀ (n = 20), 1.5 T no RF (n = 20), 0 T (n = 15). All exposure scenarios lasted 30 minutes except for brief one minute exposure in 7 T in \& out B₀. Both measures were documented utilizing a 3D ultrasound system. During sway path evaluation, the experiment was repeated with eyes both open and closed. Sway paths for all long-lasting 7 T scenarios (normal, no RF, only B₀) with eyes closed were significantly prolonged 2 minutes after exiting the scanner, normalizing after 15 minutes. Brief exposure to 7 T B₀ or 30 minutes exposure to 1.5 T or 0 T did not show significant changes. End positions after Unterberger's stepping test were significantly changed counter-clockwise after all 7 T scenarios, including the brief in \& out B₀ exposure. Shorter exposure resulted in a smaller alteration angle. In contrast to sway path, reversal of changes in body axis rotation was incomplete after 15 minutes. 1.5 T caused no rotational changes. The results show that exposure to the 7 Tesla static magnetic field causes only a temporary dysfunction or "over-compensation" of the vestibular system not measurable at 1.5 or 0 Tesla. Radiofrequency fields, gradient switching, and orthostatic dysregulation do not seem to play a role.}, language = {en} } @article{LagemaatVosMaasetal.2014, author = {Lagemaat, Miriam W. and Vos, Eline K. and Maas, Marnix C. and Bitz, Andreas and Orzada, Stephan and Uden, Mark J. van and Kobus, Thiele and Heerschap, Arend and Scheenen, Tom W. J.}, title = {Phosphorus magnetic resonance spectroscopic imaging at 7 T in patients with prostate cancer}, series = {Investigative Radiology}, volume = {49}, journal = {Investigative Radiology}, number = {5}, publisher = {Lippincott Williams \& Wilkins}, address = {Philadelphia, Pa.}, issn = {1536-0210}, doi = {10.1097/RLI.0000000000000012}, pages = {363 -- 372}, year = {2014}, abstract = {Objectives The aim of this study was to identify characteristics of phosphorus (³¹P) spectra of the human prostate and to investigate changes of individual phospholipid metabolites in prostate cancer through in vivo ³¹P magnetic resonance spectroscopic imaging (MRSI) at 7 T. Materials and Methods In this institutional review board-approved study, 15 patients with biopsy-proven prostate cancer underwent T₂-weighted magnetic resonance imaging and 3-dimensional ³¹P MRSI at 7 T. Voxels were selected at the tumor location, in normal-appearing peripheral zone tissue, normal-appearing transition zone tissue, and in the base of the prostate close to the seminal vesicles. Phosphorus metabolite ratios were determined and compared between tissue types. Results Signals of phosphoethanolamine (PE) and phosphocholine (PC) were present and well resolved in most ³¹P spectra in the prostate. Glycerophosphocholine signals were observable in 43\% of the voxels in malignant tissue, but in only 10\% of the voxels in normal-appearing tissue away from the seminal vesicles. In many spectra, independent of tissue type, 2 peaks resonated in the chemical shift range of inorganic phosphate, possibly representing 2 separate pH compartments. The PC/PE ratio in the seminal vesicles was highly elevated compared with the prostate in 5 patients. A considerable overlap of ³¹P metabolite ratios was found between prostate cancer and normal-appearing prostate tissue, preventing direct discrimination of these tissues. The only 2 patients with high Gleason scores tumors (≥4+5) presented with high PC and glycerophosphocholine levels in their cancer lesions. Conclusions Phosphorus MRSI at 7 T shows distinct features of phospholipid metabolites in the prostate gland and its surrounding structures. In this exploratory study, no differences in ³¹P metabolite ratios were observed between prostate cancer and normal-appearing prostate tissue possibly because of the partial volume effects of small tumor foci in large MRSI voxels.}, language = {en} } @article{PyschnyDoeringFeldmann2014, author = {Pyschny, D. and D{\"o}ring, Bernd and Feldmann, M.}, title = {Ermittlung der thermischen Leistungsf{\"a}higkeit des neuartigen multifunktionalen Verbunddeckensystems InaDeck}, series = {Bauingenieur : die richtungsweisende Zeitschrift im Bauingenieurswesen}, volume = {89}, journal = {Bauingenieur : die richtungsweisende Zeitschrift im Bauingenieurswesen}, number = {3}, publisher = {VDI Fachmedien}, address = {D{\"u}sseldorf}, issn = {0005-6650}, pages = {116 -- 124}, year = {2014}, language = {de} } @article{MaasVosLagemaatetal.2014, author = {Maas, Marnix C. and Vos, Eline K. and Lagemaat, Miriam W. and Bitz, Andreas and Orzada, Stephan and Kobus, Thiele and Kraff, Oliver and Maderwald, Stefan and Ladd, Mark E. and Scheenen, Tom W. J.}, title = {Feasibility of T₂-weighted turbo spin echo imaging of the human prostate at 7 tesla}, series = {Magnetic Resonance in Medicine}, volume = {71}, journal = {Magnetic Resonance in Medicine}, number = {5}, publisher = {Wiley-VCH}, address = {Weinheim}, issn = {1522-2594}, doi = {10.1002/mrm.24818}, pages = {1711 -- 1719}, year = {2014}, abstract = {Purpose To demonstrate that high quality T₂-weighted (T2w) turbo spin-echo (TSE) imaging of the complete prostate can be achieved routinely and within safety limits at 7 T, using an external transceive body array coil only. Methods Nine healthy volunteers and 12 prostate cancer patients were scanned on a 7 T whole-body system. Preparation consisted of B₀ and radiofrequency shimming and localized flip angle calibration. T₁ and T₂ relaxation times were measured and used to define the T2w-TSE protocol. T2w imaging was performed using a TSE sequence (pulse repetition time/echo time 3000-3640/71 ms) with prolonged excitation and refocusing pulses to reduce specific absorption rate. Results High quality T2w TSE imaging was performed in less than 2 min in all subjects. Tumors of patients with gold-standard tumor localization (MR-guided biopsy or prostatectomy) were well visualized on 7 T imaging (n = 3). The number of consecutive slices achievable within a 10-g averaged specific absorption rate limit of 10 W/kg was ≥28 in all subjects, sufficient for full prostate coverage with 3-mm slices in at least one direction. Conclusion High quality T2w TSE prostate imaging can be performed routinely and within specific absorption rate limits at 7 T with an external transceive body array.}, language = {en} } @article{PasteurTippkoetterKampeisetal.2014, author = {Pasteur, Aline and Tippk{\"o}tter, Nils and Kampeis, Percy and Ulber, Roland}, title = {Optimization of high gradient magnetic separation filter units for the purification of fermentation products}, series = {IEEE TRANSACTIONS ON MAGNETICS}, volume = {50}, journal = {IEEE TRANSACTIONS ON MAGNETICS}, number = {10}, publisher = {IEEE}, address = {New York, NY}, issn = {0018-9464}, doi = {10.1109/TMAG.2014.2325535}, pages = {Artikel 5000607}, year = {2014}, abstract = {High gradient magnetic separation (HGMS) has been established since the early 1970s. A more recent application of these systems is the use in bioprocesses. To integrate the HGMS in a fermentation process, it is necessary to optimize the separation matrix with regard to the magnetic separation characteristics and permeability of the non-magnetizable components of the fermentation broth. As part of the work presented here, a combined fluidic and magnetic force finite element model simulation was created using the software COMSOL Multiphysics and compared with separation experiments. Finally, as optimal lattice orientation of the separation matrix, a transversal rhombohedral arrangement was defined. The high suitability of the new filter matrix has been verified by separation experiments.}, language = {en} } @article{TippkoetterWollnySucketal.2014, author = {Tippk{\"o}tter, Nils and Wollny, Steffen and Suck, Kirstin and Sohling, Ulrich and Ruf, Friedrich and Ulber, Roland}, title = {Recycling of spent oil bleaching earth as source of glycerol for the anaerobic production of acetone, butanol, and ethanol with Clostridium diolis and lipolytic Clostridium lundense}, series = {Engineering in Life Sciences}, volume = {14}, journal = {Engineering in Life Sciences}, number = {4}, publisher = {Wiley-VCH}, address = {Weinheim}, issn = {1618-2863}, doi = {10.1002/elsc.201300113}, pages = {425 -- 432}, year = {2014}, abstract = {A major part of edible oil is subjected to bleaching procedures, primarily with minerals applied as adsorbers. Their recycling is currently done either by regaining the oil via organic solvent extraction or by using the spent bleaching earth (SBE) as additive for animal feed, etc. As a new method, the reutilization of the by-product SBE for the microbiologic formation of acetone, butanol, and ethanol (ABE) is presented as proof-of-concept. The SBE was taken from a palm oil cleaning process. The recycling concept is based on the application of lipolytic clostridia strains. Due to considerably long fermentation times, co-fermentation with Candida rugosa and enzymatic hydrolyses of the bound oil with a subsequent clostridia fermentation are shown as alternative routes. Anaerobic fermentations under comparison of different clostridia strains were performed with glycerol media, enzymatically hydrolyzed palm oil and SBE. Solutes, side product compositions and productivities were quantified via HPLC. A successful production of ABE solutes from SBE has been done with a yield of 0.15 g butanol per gram of bound glycerol. Thus, the biotechnological recycling of the waste stream is possible in principle. Inhibition of the substrate suspension has been observed. A chromatographic ion-exchange of substrates increased the biomass concentration.}, language = {en} } @article{AlKaidyDuweHusteretal.2014, author = {Al-Kaidy, Huschyar and Duwe, Anna and Huster, Manuel and Muffler, Kai and Schlegel, Christin and Sieker, Tim and Stadtm{\"u}ller, Ralf and Tippk{\"o}tter, Nils and Ulber, Roland}, title = {Biotechnologie und Bioverfahrenstechnik - Vom ersten Ullmanns Artikel bis hin zu aktuellen Forschungsthemen}, series = {Chemie Ingenieur Technik}, volume = {86}, journal = {Chemie Ingenieur Technik}, number = {12}, publisher = {Wiley-VCH}, address = {Weinheim}, issn = {0009-286X}, doi = {10.1002/cite.201400083}, pages = {2215 -- 2225}, year = {2014}, abstract = {Biotechnologie und die mit ihr verbundenen technischen Prozesse pr{\"a}gen seit Jahrtausenden die Entwicklung der Menschheit. Ausgehend von empirischen Verfahren, insbesondere zur Herstellung von Lebensmitteln und t{\"a}glichen Gebrauchsg{\"u}tern, haben sich diese Disziplinen zu einem der innovativsten Zukunftsfelder entwickelt. Durch das immer detailliertere Verst{\"a}ndnis zellul{\"a}rer Vorg{\"a}nge k{\"o}nnen mittlerweile Produktionsst{\"a}mme gezielt optimiert werden. Im Zusammenspiel mit moderner Prozesstechnik k{\"o}nnen so eine Vielzahl von Bulk- und Feinchemikalien sowie Pharmazeutika effizient hergestellt werden. In diesem Artikel werden exemplarisch einige der aktuellen Trends vorgestellt.}, language = {de} } @article{WiesenTippkoetterMuffleretal.2014, author = {Wiesen, Sebastian and Tippk{\"o}tter, Nils and Muffler, Kai and Suck, Kirstin and Sohling, Ulrich and Ruf, Nils and Ulber, Roland}, title = {Adsorptive Vorbehandlung von Rohglycerin f{\"u}r die 1,3-Propandiol Fermentation mit Clostridium diolis}, series = {Chemie Ingenieur Technik}, volume = {86}, journal = {Chemie Ingenieur Technik}, number = {1-2}, publisher = {Wiley-VCH}, address = {Weinheim}, doi = {10.1002/cite.201300080}, pages = {129 -- 135}, year = {2014}, abstract = {Bei der Gewinnung von Fetts{\"a}uren aus Pflanzen{\"o}len, z. B. zur Herstellung von Biopolymeren, oder bei der Biodiesel- und Seifenproduktion, f{\"a}llt Glycerin als Nebenprodukt an. Bei der Biokonversion dieses Rohstoffes zu 1,3-Propandiol wird der Produktionsorganismus Clostridium diolis durch Verunreinigungen im Rohglycerin gehemmt. Als inhibierende Substanzen konnten freie Fetts{\"a}uren identifiziert werden. Mithilfe eines adsorptiven Aufarbeitungsverfahrens ist es gelungen, die Fetts{\"a}uren zu entfernen und die Konversionseffizienz zu 1,3-Propandiol zu erh{\"o}hen.}, language = {de} } @inproceedings{SchirraBauschatWatmuff2014, author = {Schirra, Julian and Bauschat, J.-Michael and Watmuff, J.H.}, title = {Accurate induced drag prediction for highly non-planar lifting systems}, series = {19th Australasian Fluid Mechanics Conference : 8.-11. Dezember 2014, Melbourne, Australia}, booktitle = {19th Australasian Fluid Mechanics Conference : 8.-11. Dezember 2014, Melbourne, Australia}, pages = {4 Seiten}, year = {2014}, abstract = {The impact of wake model effects is investigated for two highly non-planar lifting systems. Dependent on the geometrical arrangement of the configuration, the wake model shape is found to considerably affect the estimation. Particularly at higher angles of attack, an accurate estimation based on the common linear wake model approaches is involved.}, language = {en} } @book{SchulteZurhausen2014, author = {Schulte-Zurhausen, Manfred}, title = {Organisation}, edition = {6., {\"u}berarb. und aktualisierte Aufl.}, publisher = {Vahlen}, address = {M{\"u}nchen}, isbn = {978-3-8006-4689-0}, pages = {XVI, 687 S. : graph. Darst.}, year = {2014}, language = {de} } @article{TippkoetterDuweWiesenetal.2014, author = {Tippk{\"o}tter, Nils and Duwe, Anna-Maria and Wiesen, Sebastian and Sieker, Tim and Ulber, Roland}, title = {Enzymatic hydrolysis of beech wood lignocellulose at high solid contents and its utilization as substrate for the production of biobutanol and dicarboxylic acids}, series = {Bioresource Technology}, volume = {167}, journal = {Bioresource Technology}, publisher = {Elsevier}, address = {Amsterdam}, doi = {10.1016/j.biortech.2014.06.052}, pages = {447 -- 455}, year = {2014}, abstract = {The development of a cost-effective hydrolysis for crude cellulose is an essential part of biorefinery developments. To establish such high solid hydrolysis, a new solid state reactor with static mixing is used. However, concentrations >10\% (w/w) cause a rate and yield reduction of enzymatic hydrolysis. By optimizing the synergetic activity of cellulolytic enzymes at solid concentrations of 9\%, 17\% and 23\% (w/w) of crude Organosolv cellulose, glucose concentrations of 57, 113 and 152 g L⁻¹ are reached. However, the glucose yield decreases from 0.81 to 0.72gg⁻¹ at 17\% (w/w). Optimal conditions for hydrolysis scale-up under minimal enzyme addition are identified. As result, at 23\% (w/w) crude cellulose the glucose yield increases from 0.29 to 0.49gg⁻¹. As proof of its applicability, biobutanol, succinic and itaconic acid are produced with the crude hydrolysate. The potential of the substrate is proven e.g. by a high butanol yield of 0.33gg⁻¹.}, language = {en} } @misc{AlKaidyTippkoetterUlber2014, author = {Al-Kaidy, Huschyar and Tippk{\"o}tter, Nils and Ulber, Roland}, title = {Vorrichtung und Verfahren zur Bestimmung des Kontaktwinkels eines fl{\"u}ssigen oder mit Fl{\"u}ssigkeit gef{\"u}llten K{\"o}rpers [Offenlegungsschrift]}, publisher = {Deutsches Patent- und Markenamt}, address = {M{\"u}nchen}, pages = {13 Seiten}, year = {2014}, abstract = {Die vorliegende Erfindung betrifft eine Vorrichtung und ein Verfahren zur Bestimmung des Kontaktwinkels eines fl{\"u}ssigen oder mit Fl{\"u}ssigkeit gef{\"u}llten K{\"o}rpers. Dieser besteht aus einem Tr{\"a}ger (1) und einer damit verbundenen, in einem Winkelbereich von mehr als 0° bis maximal 90° neigbaren Ebene (8) mit einer darin ausgebildeten Abrollbahn (9) f{\"u}r den fl{\"u}ssigen oder mit Fl{\"u}ssigkeit gef{\"u}llten K{\"o}rper. An der Ebene (8) sind mehrere Sensoren (11, 12) zur Erfassung der Rolldauer des K{\"o}rpers entlang der Rollstrecke angeordnet. Erfindungsgem{\"a}ß ist vorgesehen, dass die Einstellung des Neigungswinkels der Ebene (8) {\"u}ber ein Winkelmessger{\"a}t (10) erfolgt, wodurch ein Abrollwinkel erfassbar ist, bei dem der K{\"o}rper in Bewegung ger{\"a}t. Aus der Rolldauer, der Rollstrecke und dem Abrollwinkel wird der Kontaktwinkel des K{\"o}rpers ermittelt.}, language = {de} } @article{JoerissenHeger2014, author = {J{\"o}rissen, J{\"o}rg and Heger, Michael}, title = {Zur Wirkung hochschuldidaktisch fundierter und in den Fachbereichen verankerter Lehrveranstaltungsevaluation}, series = {Qualit{\"a}t in der Wissenschaft (QiW)}, volume = {8}, journal = {Qualit{\"a}t in der Wissenschaft (QiW)}, number = {2+3}, publisher = {Universit{\"a}tsverlag Webler}, address = {Bielefeld}, issn = {1860-3041}, pages = {70 -- 80}, year = {2014}, language = {de} } @article{HoehrPaulssenBenardetal.2014, author = {Hoehr, Cornelia and Paulßen, Elisabeth and Benard, Francois and Lee, Chris Jaeil and Hou, Xinchi and Badesso, Brian and Ferguson, Simon and Miao, Qing and Yang, Hua and Buckley, Ken and Hanemaayer, Victoire and Zeisler, Stefan and Ruth, Thomas and Celler, Anna and Schaffer, Paul}, title = {⁴⁴ᶢSc production using a water target on a 13 MeV cyclotron}, series = {Nuclear medicine and biology}, volume = {41}, journal = {Nuclear medicine and biology}, number = {5}, publisher = {Elsevier}, address = {Amsterdam}, issn = {1872-9614}, doi = {10.1016/j.nucmedbio.2013.12.016}, pages = {401 -- 406}, year = {2014}, abstract = {Access to promising radiometals as isotopes for novel molecular imaging agents requires that they are routinely available and inexpensive to obtain. Proximity to a cyclotron center outfitted with solid target hardware, or to an isotope generator for the metal of interest is necessary, both of which can introduce significant hurdles in development of less common isotopes. Herein, we describe the production of ⁴⁴Sc (t₁⸝₂ = 3.97 h, Eavg,β⁺ = 1.47 MeV, branching ratio = 94.27\%) in a solution target and an automated loading system which allows a quick turn-around between different radiometallic isotopes and therefore greatly improves their availability for tracer development. Experimental yields are compared to theoretical calculations.}, language = {en} } @inproceedings{AlKaidyUlberTippkoetter2014, author = {Al-Kaidy, H. and Ulber, R. and Tippk{\"o}tter, Nils}, title = {A platform technology for the automated reaction control in magnetizable micro-fluidic droplets}, series = {Biomaterials - made in bioreactors : book of abstracts, May 26 - 28, 2014, Radisson Blu Park Hotel and Conference Dentre, Radebeul, Germany}, booktitle = {Biomaterials - made in bioreactors : book of abstracts, May 26 - 28, 2014, Radisson Blu Park Hotel and Conference Dentre, Radebeul, Germany}, publisher = {DECHEMA}, address = {Frankfurt am Main}, pages = {21 -- 22}, year = {2014}, language = {en} } @article{Wilke2014, author = {Wilke, Thomas}, title = {Gebaute Geschichte in Turin}, series = {Kunsttexte.de}, volume = {2014}, journal = {Kunsttexte.de}, number = {1}, publisher = {Humboldt-Universit{\"a}t zu Berlin}, address = {Berlin}, issn = {1618-8101}, doi = {10.18452/7197}, pages = {13 Seiten}, year = {2014}, abstract = {St{\"a}dte sind Stein gewordene Geschichte. Ihre realisierte Form erm{\"o}glicht Geschichte zu erleben und die Stadtentwicklung nachzuvollziehen. Besonders in Turin ist ablesbar, wie das Haus Savoyen den Ausbau der neuen Hauptstadt zu einer der f{\"u}hrenden Barockmetropolen Europas beeinflusste.}, language = {de} } @misc{Jacobs2014, author = {Jacobs, Stephan}, title = {Es gibt keine nichtfunktionalen Tests. Es gibt nur nichtfunktionale Anforderungen!}, pages = {27 Folien}, year = {2014}, language = {de} } @article{LehnertzAnsmannBialonskietal.2014, author = {Lehnertz, Klaus and Ansmann, Gerrit and Bialonski, Stephan and Dickten, Henning and Geier, Christian and Porz, Stephan}, title = {Evolving networks in the human epileptic brain}, series = {Physica D: Nonlinear Phenomena}, volume = {267}, journal = {Physica D: Nonlinear Phenomena}, publisher = {Elsevier}, address = {Amsterdam}, issn = {0167-2789}, doi = {10.1016/j.physd.2013.06.009}, pages = {7 -- 15}, year = {2014}, abstract = {Network theory provides novel concepts that promise an improved characterization of interacting dynamical systems. Within this framework, evolving networks can be considered as being composed of nodes, representing systems, and of time-varying edges, representing interactions between these systems. This approach is highly attractive to further our understanding of the physiological and pathophysiological dynamics in human brain networks. Indeed, there is growing evidence that the epileptic process can be regarded as a large-scale network phenomenon. We here review methodologies for inferring networks from empirical time series and for a characterization of these evolving networks. We summarize recent findings derived from studies that investigate human epileptic brain networks evolving on timescales ranging from few seconds to weeks. We point to possible pitfalls and open issues, and discuss future perspectives.}, language = {en} } @article{Olbertz2014, author = {Olbertz, Klaus}, title = {Die arbeitsrechtliche Stellung des Prokuristen - Handelsrechtlicher Kompetenzzuwachs mit arbeitsrechtlichen Konsequenzen}, series = {NWB - Steuer- und Wirtschaftsrecht}, journal = {NWB - Steuer- und Wirtschaftsrecht}, number = {21}, publisher = {NWB-Verlag}, address = {Herne}, issn = {1860-9449}, pages = {1591 -- 1596}, year = {2014}, abstract = {Die Besch{\"a}ftigung von Prokuristen ist g{\"a}ngige betriebliche Praxis. Unternehmen stehen dabei immer wieder vor der Frage, ob und welche Arbeitnehmer sie zu Prokuristen bestellen sollen. Nicht selten bleiben hierbei die arbeitsrechtlichen Konsequenzen, die mit der Bestellung eines Arbeitnehmers zum Prokuristen einhergehen k{\"o}nnen, unber{\"u}cksichtigt, wie diverse Gerichtsentscheidungen zeigen. Dieser Beitrag soll einen {\"U}berblick {\"u}ber die arbeitsrechtlichen Folgen bei der Besch{\"a}ftigung von Prokuristen geben und der betrieblichen Praxis somit gleichzeitig als Entscheidungshilfe dienen, wenn es um das Ob und Wie der m{\"o}glichen Bestellung eines Arbeitnehmers zum Prokuristen geht.}, language = {de} } @article{Olbertz2014, author = {Olbertz, Klaus}, title = {Der neue gesetzliche Mindestlohn - was gilt und was Unternehmen k{\"u}nftig beachten m{\"u}ssen}, series = {Gesellschafts- und Wirtschaftsrecht : GWR}, journal = {Gesellschafts- und Wirtschaftsrecht : GWR}, issn = {1868-1816}, pages = {521 -- 524}, year = {2014}, abstract = {Ab dem 1.1.2015 ist es soweit: Deutschland erh{\"a}lt einen fl{\"a}chendeckenden und weitgehend branchenunabh{\"a}ngigen gesetzlichen Mindestlohn. Danach haben grunds{\"a}tzlich alle abh{\"a}ngig besch{\"a}ftigten Arbeitnehmer einen Anspruch auf eine Entlohnung von wenigstens 8,50 EUR brutto je Arbeitsstunde. Die Auswirkungen d{\"u}rften enorm sein. Das Bundesministerium f{\"u}r Arbeit und Soziales geht jedenfalls davon aus, dass aufgrund der Einf{\"u}hrung des gesetzlichen Mindestlohns mehrere Millionen Besch{\"a}ftigte einen h{\"o}heren Lohn beanspruchen k{\"o}nnen. Der nachfolgende Beitrag gibt einen {\"U}berblick {\"u}ber die wesentlichen Inhalte des gesetzlichen Mindestlohns und Hinweise f{\"u}r Anwendungsprobleme in der betrieblichen Praxis.}, language = {de} } @misc{Olbertz2014, author = {Olbertz, Klaus}, title = {Arbeitszeitbetrug rechtfertigt fristlose K{\"u}ndigung auch bei langer Betriebszugeh{\"o}rigkeit}, series = {Gesellschafts- und Wirtschaftsrecht : GWR}, journal = {Gesellschafts- und Wirtschaftsrecht : GWR}, issn = {1868-1816}, pages = {465 -- 465}, year = {2014}, language = {de} } @article{Olbertz2014, author = {Olbertz, Klaus}, title = {Gestaltung des Anstellungsvertrags - Der Compliance-Beauftragte}, series = {Arbeit und Arbeitsrecht : AuA}, journal = {Arbeit und Arbeitsrecht : AuA}, number = {7}, publisher = {Huss Medien}, address = {Berlin}, issn = {0323-4568}, pages = {400 -- 403}, year = {2014}, abstract = {Ein Compliance-Beauftragter soll daf{\"u}r Sorge tragen, dass aus dem Unternehmen heraus keine Rechtsverletzungen begangen werden. Aber welche rechtlichen Notwendigkeiten und M{\"o}glichkeiten resultieren daraus f{\"u}r die Gestaltung des Anstellungsvertrags?}, language = {de} } @misc{Olbertz2014, author = {Olbertz, Klaus}, title = {Vorbesch{\"a}ftigungszeiten als Leiharbeitnehmer z{\"a}hlen f{\"u}r K{\"u}ndigungsschutz grunds{\"a}tzlich nicht mit}, series = {Gesellschafts- und Wirtschaftsrecht : GWR}, journal = {Gesellschafts- und Wirtschaftsrecht : GWR}, issn = {1868-1816}, pages = {423 -- 423}, year = {2014}, language = {de} } @misc{Olbertz2014, author = {Olbertz, Klaus}, title = {Kein Anspruch auf Tarifgehaltserh{\"o}hungen bei K{\"u}ndigung des in Bezug genommenen Anerkennungstarifvertrags}, series = {Gesellschafts- und Wirtschaftsrecht : GWR}, journal = {Gesellschafts- und Wirtschaftsrecht : GWR}, issn = {1868-1816}, pages = {377 -- 377}, year = {2014}, language = {de} } @misc{Olbertz2014, author = {Olbertz, Klaus}, title = {Arbeitnehmereigenschaft des mitarbeitenden Gesellschafters einer GmbH}, series = {Gesellschafts- und Wirtschaftsrecht : GWR}, journal = {Gesellschafts- und Wirtschaftsrecht : GWR}, issn = {1868-1816}, pages = {532 -- 532}, year = {2014}, language = {de} } @article{Tran2014, author = {Tran, Duc Hung}, title = {Multiple corporate governance attributes and the cost of capital - Evidence from Germany}, series = {The British Accounting Review}, volume = {46}, journal = {The British Accounting Review}, number = {2}, publisher = {Elsevier}, address = {Amsterdam}, issn = {0890-8389}, doi = {https://doi.org/10.1016/j.bar.2014.02.003}, pages = {179 -- 197}, year = {2014}, abstract = {This paper investigates the extent to which corporate governance affects the cost of debt and equity capital of German exchange-listed companies. I examine corporate governance along three dimensions: financial information quality, ownership structure and board structure. The results suggest that firms with high levels of financial transparency and bonus compensations face lower cost of equity. In addition, block ownership is negatively related to firms' cost of equity when the blockholders are other firms, managers or founding-family members. Consistent with the conjecture that agency costs increase with firm size, I find significant cost of debt effects only in the largest German companies. Here, the creditors demand lower cost of debt from firms with block ownerships held by corporations or banks. My findings demonstrate that a uniform set of governance attributes is unlikely to satisfy suppliers of debt and equity capital equally.}, language = {en} } @inproceedings{Behbahani2014, author = {Behbahani, Mehdi}, title = {An Experimental Study of Thrombocyte Reactions in Response to Biomaterial Surfaces and Varying Shear Stress}, series = {Proceedings of the International Conference on Biomedical Engineering and Systems Prague, Czech Republic, August 14-15, 2014}, booktitle = {Proceedings of the International Conference on Biomedical Engineering and Systems Prague, Czech Republic, August 14-15, 2014}, pages = {Paper 125}, year = {2014}, language = {en} } @article{LuisierLempiaeinenScherbichleretal.2014, author = {Luisier, Rapha{\"e}lle and Lempi{\"a}inen, Harri and Scherbichler, Nina and Braeuning, Albert and Geissler, Miriam and Dubost, Valerie and M{\"u}ller, Arne and Scheer, Nico and Chibout, Salah-Dine and Hara, Hisanori and Picard, Frank and Theil, Diethilde and Couttet, Philippe and Vitobello, Antonio and Grenet, Olivier and Grasl-Kraupp, Bettina and Ellinger-Ziegelbauer, Heidrung and Thomson, John P. and Meehan, Richard R. and Elcombe, Clifford R. and Henderson, Colin J. and Wolf, C. Roland and Schwarz, Michael and Moulin, Pierre and Terranova, Remi and Moggs, Jonathan G.}, title = {Phenobarbital Induces Cell Cycle Transcriptional Responses in Mouse Liver Humanized for Constitutive Androstane and Pregnane X Receptors}, series = {Toxicological Sciences}, volume = {139}, journal = {Toxicological Sciences}, number = {2}, publisher = {Oxford University Press}, address = {Oxford}, issn = {1094-2025}, doi = {https://doi.org/10.1093/toxsci/kfu038}, pages = {501 -- 511}, year = {2014}, abstract = {The constitutive androstane receptor (CAR) and the pregnane X receptor (PXR) are closely related nuclear receptors involved in drug metabolism and play important roles in the mechanism of phenobarbital (PB)-induced rodent nongenotoxic hepatocarcinogenesis. Here, we have used a humanized CAR/PXR mouse model to examine potential species differences in receptor-dependent mechanisms underlying liver tissue molecular responses to PB. Early and late transcriptomic responses to sustained PB exposure were investigated in liver tissue from double knock-out CAR and PXR (CARᴷᴼ-PXRᴷᴼ), double humanized CAR and PXR (CARʰ-PXRʰ), and wild-type C57BL/6 mice. Wild-type and CARʰ-PXRʰ mouse livers exhibited temporally and quantitatively similar transcriptional responses during 91 days of PB exposure including the sustained induction of the xenobiotic response gene Cyp2b10, the Wnt signaling inhibitor Wisp1, and noncoding RNA biomarkers from the Dlk1-Dio3 locus. Transient induction of DNA replication (Hells, Mcm6, and Esco2) and mitotic genes (Ccnb2, Cdc20, and Cdk1) and the proliferation-related nuclear antigen Mki67 were observed with peak expression occurring between 1 and 7 days PB exposure. All these transcriptional responses were absent in CARᴷᴼ-PXRᴷᴼ mouse livers and largely reversible in wild-type and CARʰ-PXRʰ mouse livers following 91 days of PB exposure and a subsequent 4-week recovery period. Furthermore, PB-mediated upregulation of the noncoding RNA Meg3, which has recently been associated with cellular pluripotency, exhibited a similar dose response and perivenous hepatocyte-specific localization in both wild-type and CARʰ-PXRʰ mice. Thus, mouse livers coexpressing human CAR and PXR support both the xenobiotic metabolizing and the proliferative transcriptional responses following exposure to PB.}, language = {en} } @article{SalpatiChuChenetal.2014, author = {Salpati, Laurent and Chu, Xiaoyan and Chen, Liangfu and Prasad, Bhagwat and Dallas, Shannon and Evers, Raymond and Mamaril-Fishman, Donna and Geier, Ethan G. and Kehler, Jonathan and Kunta, Jeevan and Mezler, Mario and Laplanche, Loic and Pang, Jodie and Soars, Matthew G. and Unadkat, Jashvant D. and van Waterschoot, Robert A.B. and Yabut, Jocelyn and Schinkel, Alfred H. and Scheer, Nico and Rode, Anja}, title = {Evaluation of organic anion transporting polypeptide 1B1 and 1B3 humanized mice as a translational model to study the pharmacokinetics of statins}, series = {Drug Metabolism and Disposition}, volume = {42}, journal = {Drug Metabolism and Disposition}, number = {8}, publisher = {ASPET}, address = {Bethesda, Md.}, issn = {1521-009X}, doi = {10.1124/dmd.114.057976}, pages = {1301 -- 1313}, year = {2014}, abstract = {Organic anion transporting polypeptide (Oatp) 1a/1b knockout and OATP1B1 and -1B3 humanized mouse models are promising tools for studying the roles of these transporters in drug disposition. Detailed characterization of these models will help to better understand their utility for predicting clinical outcomes. To advance this approach, we carried out a comprehensive analysis of these mouse lines by evaluating the compensatory changes in mRNA expression, quantifying the amounts of OATP1B1 and -1B3 protein by liquid chromatography-tandem mass spectrometry, and studying the active uptake in isolated hepatocytes and the pharmacokinetics of some prototypical substrates including statins. Major outcomes from these studies were 1) mostly moderate compensatory changes in only a few genes involved in drug metabolism and disposition, 2) a robust hepatic expression of OATP1B1 and -1B3 proteins in the respective humanized mouse models, and 3) functional activities of the human transporters in hepatocytes isolated from the humanized models with several substrates tested in vitro and with pravastatin in vivo. However, the expression of OATP1B1 and -1B3 in the humanized models did not significantly alter liver or plasma concentrations of rosuvastatin and pitavastatin compared with Oatp1a/1b knockout controls under the conditions used in our studies. Hence, although the humanized OATP1B1 and -1B3 mice showed in vitro and/or in vivo functional activity with some statins, further characterization of these models is required to define their potential use and limitations in the prediction of drug disposition and drug-drug interactions in humans.}, language = {en} } @article{KrollLudwigsKaesling2014, author = {Kroll-Ludwigs, Kathrin and Kaesling, Katharina}, title = {Family Law and Culture in Europe: Developments, Challenges and Opportunities - Konferenz der Commission on European Family Law vom 29.-31. August 2013, Bonn}, series = {Zeitschrift f{\"u}r Europ{\"a}isches Privatrecht (ZEuP)}, journal = {Zeitschrift f{\"u}r Europ{\"a}isches Privatrecht (ZEuP)}, number = {3}, publisher = {Beck}, address = {M{\"u}nchen}, issn = {0943-3929}, pages = {673 -- 676}, year = {2014}, abstract = {Vor dem Hintergrund zunehmender gesellschaftlicher Ver{\"a}nderungen bei den Lebens- und Familienformen hat es sich die Commission on European Family Law (CEFL) seit 2001 zum Ziel gesetzt, unverbindliche Regelungsvorschl{\"a}ge f{\"u}r ein europaweit einheitliches Familienrecht zu schaffen. Die Vorstellung und Diskussion dieser auf rechtsvergleichender Basis erstellten Principles erfolgt auf den regelm{\"a}ßig veranstalteten Tagungen der CEFL. Die nunmehr f{\"u}nfte Konferenz zum Thema „Family Law and Culture in Europe - Developments, Challenges and Opportunities" fand erstmals in Deutschland statt. Ausgerichtet wurde die Veranstaltung, zu der ca. 200 Teilnehmerinnen und Teilnehmern aus Wissenschaft und Praxis aus insgesamt 33 L{\"a}ndern angereist waren, von Nina Dethloff (Direktorin des Instituts f{\"u}r Deutsches, Europ{\"a}isches und Internationales Familienrecht an der Universit{\"a}t Bonn), Katharina Boele-Woelki (Direktorin des Utrecht Centre for European Research into Family Law und Preistr{\"a}gerin des Anneliese Maier-Forschungspreises der Alexander von Humboldt-Stiftung) und Werner Gephart (Direktor des K{\"a}te Hamburger Kollegs „Recht als Kultur").}, language = {de} } @article{Bernecker2014, author = {Bernecker, Andreas}, title = {Do politicians shirk when reelection is certain? Evidence from the German parliament}, series = {European Journal of Political Economy}, volume = {36}, journal = {European Journal of Political Economy}, publisher = {Elsevier}, address = {Amsterdam}, issn = {0176-2680}, doi = {10.1016/j.ejpoleco.2014.07.001}, pages = {55 -- 70}, year = {2014}, abstract = {Does stiffer electoral competition reduce political shirking? For a micro-analysis of this question, I construct a new data set spanning the years 2005 to 2012 covering biographical and political information about German Members of Parliament (MPs), including their attendance rates in voting sessions. For the parliament elected in 2009, I show that indeed opposition party MPs who expect to face a close race in their district show significantly and relevantly lower absence rates in parliament beforehand. MPs of governing parties seem not to react significantly to electoral competition. These results are confirmed by an analysis of the parliament elected in 2005, by several robustness checks, and also by employing an instrumental variable strategy exploiting convenient peculiarities of the German electoral system. The study also shows how MPs elected via party lists react to different levels of electoral competition.}, language = {en} } @article{Bernecker2014, author = {Bernecker, Andreas}, title = {Divided Government and the Adoption of Economic Reforms}, series = {CESifo DICE Report - Journal for Institutional Comparison}, volume = {12}, journal = {CESifo DICE Report - Journal for Institutional Comparison}, number = {4}, publisher = {Ifo Institute for Economic Research}, address = {M{\"u}nchen}, issn = {1612-0663}, pages = {47 -- 52}, year = {2014}, language = {en} } @book{Bernecker2014, author = {Bernecker, Andreas}, title = {Essays in Empirical Political Economics}, pages = {XI, 174 S. : Ill., graph. Darst.}, year = {2014}, language = {en} } @incollection{KrollLudwigs2014, author = {Kroll-Ludwigs, Kathrin}, title = {Vorbemerkung vor \S 1353}, series = {Erman, B{\"u}rgerliches Gesetzbuch : Handkommentar mit AGG, EGBGB (Auszug) , ErbbauRG, LPartG, ProdHaftG, VBVG, VersAus-glG und WEG}, booktitle = {Erman, B{\"u}rgerliches Gesetzbuch : Handkommentar mit AGG, EGBGB (Auszug) , ErbbauRG, LPartG, ProdHaftG, VBVG, VersAus-glG und WEG}, editor = {Ermann, Walter, and Grunewald, Barbara and Maier-Reimer, Georg}, publisher = {Verlag Dr. Otto Schmidt}, address = {K{\"o}ln}, isbn = {978-3-50447-102-6}, year = {2014}, language = {de} } @incollection{KrollLudwigs2014, author = {Kroll-Ludwigs, Kathrin}, title = {Vorbemerkung vor \S 1297}, series = {B{\"u}rgerliches Gesetzbuch : Handkommentar mit AGG, EGBGB (Auszug), ErbbauRG, HausratsVO, LPartG, ProdHaftG, UKlaG, VAHRG und WEG}, booktitle = {B{\"u}rgerliches Gesetzbuch : Handkommentar mit AGG, EGBGB (Auszug), ErbbauRG, HausratsVO, LPartG, ProdHaftG, UKlaG, VAHRG und WEG}, editor = {Ermann, Walter and Grunewald, Barbara and Maier-Reimer, Georg}, publisher = {Verlag Dr. Otto Schmidt}, address = {K{\"o}ln}, isbn = {978-3-504-47102-6}, year = {2014}, language = {de} } @incollection{KrollLudwigs2014, author = {Kroll-Ludwigs, Kathrin}, title = {Einleitung vor \S 1297}, series = {B{\"u}rgerliches Gesetzbuch : Handkommentar mit AGG, EGBGB (Auszug), ErbbauRG, HausratsVO, LPartG, ProdHaftG, UKlaG, VAHRG und WEG}, booktitle = {B{\"u}rgerliches Gesetzbuch : Handkommentar mit AGG, EGBGB (Auszug), ErbbauRG, HausratsVO, LPartG, ProdHaftG, UKlaG, VAHRG und WEG}, publisher = {Verlag Dr. Otto Schmidt}, address = {K{\"o}ln}, isbn = {978-3-504-47102-6}, year = {2014}, language = {de} } @article{ScheerMclaughlinRodeetal.2014, author = {Scheer, Nico and Mclaughlin, Lesley A. and Rode, Anja and MacLeod, Alastair Kenneth and Henderson, Colin J. and Wolf, Roland C.}, title = {Deletion of thirty murine cytochrome P450 genes results in viable mice with compromised drug metabolism}, series = {Drug Metabolism and Disposition}, volume = {42}, journal = {Drug Metabolism and Disposition}, number = {6}, publisher = {ASPET}, address = {Bethesda, Md.}, issn = {1521-009X}, doi = {10.1124/dmd.114.057885}, pages = {1022 -- 1030}, year = {2014}, abstract = {In humans, 75\% of all drugs are metabolized by the cytochrome P450-dependent monooxygenase system. Enzymes encoded by the CYP2C, CYP2D, and CYP3A gene clusters account for ∼80\% of this activity. There are profound species differences in the multiplicity of cytochrome P450 enzymes, and the use of mouse models to predict pathways of drug metabolism is further complicated by overlapping substrate specificity between enzymes from different gene families. To establish the role of the hepatic and extrahepatic P450 system in drug and foreign chemical disposition, drug efficacy, and toxicity, we created a unique mouse model in which 30 cytochrome P450 genes from the Cyp2c, Cyp2d, and Cyp3a gene clusters have been deleted. Remarkably, despite a wide range of putative important endogenous functions, Cyp2c/2d/3a KO mice were viable and fertile, demonstrating that these genes have evolved primarily as detoxification enzymes. Although there was no overt phenotype, detailed examination showed Cyp2c/2d/3a KO mice had a smaller body size (15\%) and larger livers (20\%). Changes in hepatic morphology and a decreased blood glucose (30\%) were also noted. A five-drug cocktail of cytochrome P450 isozyme probe substrates were used to evaluate changes in drug pharmacokinetics; marked changes were observed in either the pharmacokinetics or metabolites formed from Cyp2c, Cyp2d, and Cyp3a substrates, whereas the metabolism of the Cyp1a substrate caffeine was unchanged. Thus, Cyp2c/2d/3a KO mice provide a powerful model to study the in vivo role of the P450 system in drug metabolism and efficacy, as well as in chemical toxicity.}, language = {en} } @article{AkimbekovDigelZhubanova2014, author = {Akimbekov, N. Sh. and Digel, Ilya and Zhubanova, A. A.}, title = {Advantages of creation of e-books in training of specialists biologists and biotechnologists}, series = {KazNU Bulletin. Biology series.}, volume = {60}, journal = {KazNU Bulletin. Biology series.}, number = {1}, publisher = {Al-Farabi Kazakh National University}, address = {Almaty}, issn = {1563-0218}, pages = {249 -- 252}, year = {2014}, abstract = {The necessity of e-books as a primary of learning, its opportunities for realization of competence during training biologist and biotechnologist specialists are determined. Definitions and requirements to the e-books, its advantages in comparison with traditional textbooks, and the ways of creation of e-books in the SunRav BookEditor program are considered.}, language = {ru} } @article{AkimbekovDigelOHerasetal.2014, author = {Akimbekov, N.Sh. and Digel, Ilya and O´Heras, C. and Tastambek, K.T. and Savitskaya, I.S. and Ualyeva, P.S. and Mansurov, Z.A. and Zhubanova, A.A.}, title = {Adsorption of bacterial lipopolysaccharides on carbonized rice husks obtained in the batch experiments}, series = {Experimental Biology}, volume = {60}, journal = {Experimental Biology}, number = {1/2}, publisher = {Al-Farabi Kazakh National University}, address = {Almaty}, issn = {1563-0218}, pages = {144 -- 148}, year = {2014}, abstract = {The scope of this study is the measurement of endotoxin adsorption rate for carbonized rice husk. It showed good adsorption properties for LPS. During the batch experiments, several techniques were used and optimized for improving the material's adsorption behavior. Also, with the results obtained it was possible to differentiate the materials according to their adsorption capacity and kinetic characteristics.}, language = {en} } @article{ScheerWolf2014, author = {Scheer, Nico and Wolf, C. Roland}, title = {Genetically humanized mouse models of drug metabolizing enzymes and transporters and their applications}, series = {Xenobiotica}, volume = {44}, journal = {Xenobiotica}, number = {2}, publisher = {Taylor \& Francis}, address = {Abingdon}, issn = {1366-5928}, doi = {10.3109/00498254.2013.815831}, pages = {96 -- 108}, year = {2014}, abstract = {1. Drug metabolizing enzymes and transporters play important roles in the absorption, metabolism, tissue distribution and excretion of various compounds and their metabolites and thus can significantly affect their efficacy and safety. Furthermore, they can be involved in drug-drug interactions which can result in adverse responses, life-threatening toxicity or impaired efficacy. Significant species differences in the interaction of compounds with drug metabolizing enzymes and transporters have been described. 2. In order to overcome the limitation of animal models in accurately predicting human responses, a large variety of mouse models humanized for drug metabolizing enzymes and to a lesser extent drug transporters have been created. 3. This review summarizes the literature describing these mouse models and their key applications in studying the role of drug metabolizing enzymes and transporters in drug bioavailability, tissue distribution, clearance and drug-drug interactions as well as in human metabolite testing and risk assessment. 4. Though such humanized mouse models have certain limitations, there is great potential for their use in basic research and for testing and development of new medicines. These limitations and future potentials will be discussed.}, language = {en} } @article{HentschkeHagerHojdis2014, author = {Hentschke, Reinhard and Hager, Jonathan and Hojdis, Nils}, title = {Molecular Modeling Approach to the Prediction of Mechanical Properties of Silica-Reinforced Rubbers}, series = {Journal of Applied Polymer Science}, volume = {131}, journal = {Journal of Applied Polymer Science}, number = {18}, publisher = {Wiley}, address = {New York, NY}, issn = {1097-4628}, doi = {10.1002/app.40806}, pages = {1 -- 9}, year = {2014}, abstract = {Recently, we have suggested a nanomechanical model for dissipative loss in filled elastomer networks in the context of the Payne effect. The mechanism is based on a total interfiller particle force exhibiting an intermittent loop, due to the combination of short-range repulsion and dispersion forces with a long-range elastic attraction. The sum of these forces leads, under external strain, to a spontaneous instability of "bonds" between the aggregates in a filler network and attendant energy dissipation. Here, we use molecular dynamics simulations to obtain chemically realistic forces between surface modified silica particles. The latter are combined with the above model to estimate the loss modulus and the low strain storage modulus in elastomers containing the aforementioned filler-compatibilizer systems. The model is compared to experimental dynamic moduli of silica filled rubbers. We find good agreement between the model predictions and the experiments as function of the compatibilizer's molecular structure and its bulk concentration.}, language = {en} } @inproceedings{MaikeLenzWolf2014, author = {Maike, M{\"u}ller and Lenz, Laura and Wolf, Martin}, title = {Steigerung der Effektivit{\"a}t durch Prozessmodellierungs-Tools - {\"A}nderbarkeit und Transparenz von Prozessen am Beispiel der Business Simulation Apollo 13}, series = {Informatik 2014}, booktitle = {Informatik 2014}, publisher = {Gesellschaft f{\"u}r Informatik e.V.}, address = {Bonn}, isbn = {978-3-88579-626-8}, issn = {1617-5468}, pages = {357 -- 369}, year = {2014}, abstract = {Die Nutzung von Prozessmodellierungsmethoden oder - werkzeugen kann erheblichen Einfluss auf die Effektivit{\"a}t von Prozessen haben. Das gilt insbesondere f{\"u}r Situationen, in denen Personen unter Stress stehen oder unge{\"u}bt sind. In diesen F{\"a}llen geben Prozessmodelle konkrete Empfehlungen, nach denen sich die handelnden Personen richten k{\"o}nnten. In Experimenten mit der Business-Simulation Apollo 13 haben wir den Effekt eines Einsatzes von Prozessmodellierungsmethoden und -werkzeugen untersucht. Bereits bekannte Theorien (z.B. {\"u}ber geeignete Verh{\"a}ltnisse von Kommunikationsinhalten) konnten best{\"a}tigt werden. Dar{\"u}ber hinaus haben wir eine besondere Bedeutung der {\"U}bertragbarkeit von Prozessmodellen in konkrete Handlungen identifiziert.}, language = {de} } @inproceedings{AltayButenwegKlinkel2014, author = {Altay, Okyay and Butenweg, Christoph and Klinkel, Sven}, title = {Vibration mitigation of wind turbine towers by a new semiactive Tuned Liquid Column Damper}, series = {6. Word Congress on Structural Control and Monitoring, 15 - 17 July, 2014 Barcelona,Spain}, booktitle = {6. Word Congress on Structural Control and Monitoring, 15 - 17 July, 2014 Barcelona,Spain}, year = {2014}, language = {en} } @article{PoghossianSchoening2014, author = {Poghossian, Arshak and Sch{\"o}ning, Michael Josef}, title = {Label-free sensing of biomolecules with field-effect devices for clinical applications}, series = {Electroanalysis}, volume = {26}, journal = {Electroanalysis}, number = {6}, publisher = {Wiley-VCH}, address = {Weinheim}, issn = {1521-4109 (E-Journal); 1040-0397 (Print)}, doi = {10.1002/elan.201400073}, pages = {1197 -- 1213}, year = {2014}, abstract = {Among the variety of transducer concepts proposed for label-free detection of biomolecules, the semiconductor field-effect device (FED) is one of the most attractive platforms. As medical techniques continue to progress towards diagnostic and therapies based on biomarkers, the ability of FEDs for a label-free, fast and real-time detection of multiple pathogenic and physiologically relevant molecules with high specificity and sensitivity offers very promising prospects for their application in point-of-care and personalized medicine for an early diagnosis and treatment of diseases. The presented paper reviews recent advances and current trends in research and development of different FEDs for label-free, direct electrical detection of charged biomolecules by their intrinsic molecular charge. The authors are mainly focusing on the detection of the DNA hybridization event, antibody-antigen affinity reaction as well as clinically relevant biomolecules such as cardiac and cancer biomarkers.}, language = {en} } @article{OberlaenderKirchnerBoyenetal.2014, author = {Oberl{\"a}nder, Jan and Kirchner, Patrick and Boyen, Hans-Gerd and Sch{\"o}ning, Michael Josef}, title = {Detection of hydrogen peroxide vapor by use of manganese(IV) oxide as catalyst for calorimetric gas sensors}, series = {Physica status solidi A: Applications and materials science}, volume = {211}, journal = {Physica status solidi A: Applications and materials science}, number = {6}, publisher = {Wiley-VCH}, address = {Weinheim}, issn = {1521-396X (E-Journal); 1862-6319 (E-Journal); 0031-8965 (Print); 1862-6300 (Print)}, doi = {10.1002/pssa.201330359}, pages = {1372 -- 1376}, year = {2014}, abstract = {In this work, the catalyst manganese(IV) oxide (MnO2), of calorimetric gas sensors (to monitor the sterilization agent vaporized hydrogen peroxide) has been investigated in more detail. Chemical analyses by means of X-ray-induced photoelectron spectroscopy have been performed to unravel the surface chemistry prior and after exposure to hydrogen peroxide vapor at elevated temperature, as applied in the sterilization processes of beverage cartons. The surface characterization reveals a change in oxidation states of the metal oxide catalyst after exposure to hydrogen peroxide. Additionally, a cleaning effect of the catalyst, which itself is attached to the sensor surface by means of a polymer interlayer, could be observed.}, language = {en} } @article{ButenwegSchmittRosen2014, author = {Butenweg, Christoph and Schmitt, T. and Rosen, B.}, title = {Seismische Einwirkungen auf erdverlegte Rohrleitungen}, series = {Bauingenieur}, volume = {89}, journal = {Bauingenieur}, publisher = {VDI Fachmedien}, address = {D{\"u}sseldorf}, issn = {0005-6650}, pages = {316 -- 324}, year = {2014}, abstract = {Die erdbebensichere Auslegung von erdverlegten Rohrleitungssystemen ist von wesentlicher Bedeutung zur Sicherstellung der Funktionalit{\"a}t der Versorgungsinfrastruktur nach einem Erdbebenereignis. Zur Vermeidung von Netzausf{\"a}llen ist es erforderlich, die r{\"a}umlich weit ausgedehnten Leitungssysteme mit geeigneten rechnerischen Modellen seismisch zu bemessen. Der vorliegende Beitrag behandelt die Beanspruchung von Rohrleitungssystemen durch seismische Welleneinwirkung und stellt geeignete N{\"a}herungsans{\"a}tze und ein detailliertes Rechenmodell f{\"u}r seismische Leitungsanalysen vor. Mit den Ans{\"a}tzen wird in Berechnungsbeispielen der Einfluss wesentlicher Parameter auf die seismisch induzierten Dehnungen in Rohrleitungssystemen untersucht.}, language = {de} } @article{AltherrEdererLorenzetal.2014, author = {Altherr, Lena and Ederer, Thorsten and Lorenz, Ulf and Pelz, Peter F. and P{\"o}ttgen, Philipp}, title = {Experimental validation of an enhanced system synthesis approach}, series = {Operations Research Proceedings 2014}, journal = {Operations Research Proceedings 2014}, editor = {L{\"u}bbecke, Marco and Koster, Arie and Letmathe, Peter and Madlener, Reihard and Peis, Britta and Walther, Grit}, publisher = {Springer}, address = {Basel}, isbn = {978-3-319-28695-2}, doi = {10.1007/978-3-319-28697-6_1}, pages = {6}, year = {2014}, abstract = {Planning the layout and operation of a technical system is a common task for an engineer. Typically, the workflow is divided into consecutive stages: First, the engineer designs the layout of the system, with the help of his experience or of heuristic methods. Secondly, he finds a control strategy which is often optimized by simulation. This usually results in a good operating of an unquestioned sys- tem topology. In contrast, we apply Operations Research (OR) methods to find a cost-optimal solution for both stages simultaneously via mixed integer program- ming (MILP). Technical Operations Research (TOR) allows one to find a provable global optimal solution within the model formulation. However, the modeling error due to the abstraction of physical reality remains unknown. We address this ubiq- uitous problem of OR methods by comparing our computational results with mea- surements in a test rig. For a practical test case we compute a topology and control strategy via MILP and verify that the objectives are met up to a deviation of 8.7\%.}, language = {en} } @article{Golland2014, author = {Golland, Alexander}, title = {Datenschutz durch modulare Zertifizierung: Trusted Cloud-Pilotprojekt bringt neuen Ansatz}, series = {DSB Datenschutz-Berater}, volume = {38}, journal = {DSB Datenschutz-Berater}, number = {10}, publisher = {dfv Mediengruppe}, address = {Frankfurt a.M.}, isbn = {0170-7256}, pages = {213 -- 215}, year = {2014}, language = {de} } @article{GollandEngling2014, author = {Golland, Alexander and Engling, Christoph}, title = {a-i3/BSI Symposium 2014: Sicherheit von Daten und Identit{\"a}ten angesichts NSA und Big Data}, series = {DSB Datenschutz-Berater}, volume = {38}, journal = {DSB Datenschutz-Berater}, number = {7-8}, publisher = {dfv Mediengruppe}, address = {Frankfurt a.M.}, isbn = {0170-7256}, pages = {165 -- 166}, year = {2014}, language = {de} } @inproceedings{ButenwegRajan2014, author = {Butenweg, Christoph and Rajan, Sreelakshmy}, title = {Design and construction techniques of AAC masonry buildings in earthquakes regions}, series = {10 years Xella research in Building Materials : Symposium on the 4th and 5th of September, Potsdam 2014}, booktitle = {10 years Xella research in Building Materials : Symposium on the 4th and 5th of September, Potsdam 2014}, year = {2014}, language = {en} } @inproceedings{ButenwegMeyerFehling2014, author = {Butenweg, Christoph and Meyer, Udo and Fehling, Ekkehard}, title = {INSYSME: first activities of the German partners}, series = {9th International Masonry Conference 2014 in Guimaraes, Portugal, 2014}, booktitle = {9th International Masonry Conference 2014 in Guimaraes, Portugal, 2014}, year = {2014}, language = {en} } @article{YangKriechbaumerAlbrachtetal.2014, author = {Yang, Peng-Fei and Kriechbaumer, Andreas and Albracht, Kirsten and Sanno, Maximilian and Ganse, Bergita and Koy, Timmo and Shang, Peng and br{\"u}ggemann, Gert-Peter and M{\"u}ller, Lars Peter and Rittweger, J{\"o}rn}, title = {A novel optical approach for assessing in vivo bone segment deformation and its application in muscle-bone relationship studies in humans}, series = {Journal of Orthopaedic Translation}, volume = {2}, journal = {Journal of Orthopaedic Translation}, number = {4}, publisher = {Elsevier}, address = {Singapore}, issn = {2214-0328}, doi = {10.1016/j.jot.2014.07.078}, pages = {238 -- 238}, year = {2014}, language = {en} } @article{FinkenbergerSchlaich2014, author = {Finkenberger, Isabel Maria and Schlaich, Christoph}, title = {Mehr als Wohnen. Vom Zusammenleben in integrierten Nachbarschaften}, series = {APuZ - Aus Politik und Zeitgeschichte}, volume = {2014}, journal = {APuZ - Aus Politik und Zeitgeschichte}, number = {20-21}, publisher = {Bundeszentrale f{\"u}r politische Bildung - bpb}, address = {Bonn}, issn = {2194-3621}, pages = {46 -- 52}, year = {2014}, abstract = {Neue D{\"o}rfer braucht das Land! D{\"o}rfer in der Stadt und D{\"o}rfer auf dem Land (…). Die Planung und Gestaltung nachhaltiger Raumsysteme, die durch ein neues Verst{\"a}ndnis des gemeinschaftlichen Besitzes (und dessen Nutzung) ressourcenfressende Individualisierungstendenzen unserer Gesellschaft {\"u}berwinden, aber zugleich gr{\"o}ßtm{\"o}glichen Freiraum f{\"u}r eine individuelle Pers{\"o}nlichkeitsentfaltung zur Verf{\"u}gung stellen." Dieses Zitat der Hamburger Initiative "Wir sind Dorf" beschreibt eine aktuelle Diskussion in unserer Gesellschaft, die sowohl in der Forschung und forschungsgeleiteten Initiativen, in Politik und Planung als auch in der B{\"u}rger-schaft stattfindet. Sie wird nicht nur auf wissenschaftlichen Veranstaltungen gef{\"u}hrt, sondern auch in konkreten Projekten f{\"u}r integrative Lebenswelten, die Fragestellungen von Ern{\"a}hrung und Energieversorgung, von Arbeit und {\"O}konomie, aber auch eines neuen r{\"a}umlichen und sozialen Miteinanders einbeziehen. Anders als bei den weit verbreiteten Baugruppen geht es nicht ausschließlich um die Schaffung von Wohnraum. Die Nachbarschaftsidee verbindet das Bed{\"u}rfnis nach gemeinschaftlichem Wohnen und Wirtschaften mit einer neuen Werteorientierung, die auf pers{\"o}nlicher Verantwortungs{\"u}bernahme beruht.}, language = {de} } @article{Finkenberger2014, author = {Finkenberger, Isabel Maria}, title = {Vox populi. (Transformations-)potenziale nachkriegsmoderner Freiraumressourcen}, series = {Stadt+Gr{\"u}n}, volume = {2014}, journal = {Stadt+Gr{\"u}n}, number = {1}, publisher = {Patzer}, address = {Berlin}, issn = {0948-9770}, pages = {31 -- 35}, year = {2014}, abstract = {Heute wie damals werden die großz{\"u}gigen und offenen Siedlungsstrukturen der ersten Nachkriegsjahrzehnte mit ihrem hohen Anteil an "Gr{\"u}n" vielfach gesch{\"a}tzt und als solche nicht grundlegend hinterfragt. "Gr{\"u}n" verheißt im Allgemeinen Licht, Luft und Sonne, Freizeit und Erholung und gilt als etwas W{\"u}nschenswertes im st{\"a}dtischen Kontext. Unbeachtet bleibt, dass dem Begriff "Gr{\"u}n" zun{\"a}chst keine Eigenschaften oder Qualit{\"a}ten zugewiesen sind - er sagt noch lange nichts {\"u}ber dessen r{\"a}umliche Qualit{\"a}t, dessen Nutzbarkeit, Erreichbarkeit und Zug{\"a}nglichkeit aus. Abstandsgr{\"u}n und Straßenbegleitgr{\"u}n ist eben auch "Gr{\"u}n". Neben einer quantitativen Argumentation, welche {\"o}kologischen Aspekte wie Biotopvernetzung, Stadt- und Mikroklima ber{\"u}cksichtigt, sollten wir verst{\"a}rkt qualitativ denken und damit die Grundlage f{\"u}r einen erweiterten und wesentlich differenzierteren Diskurs {\"u}ber urbane Freir{\"a}ume ebnen.}, language = {de} } @misc{EickmannEschFunkeetal.2014, author = {Eickmann, Matthias and Esch, Thomas and Funke, Harald and Abanteriba, Sylvester and Roosen, Petra}, title = {Biofuels in Aviation - Safety Implications of Bio-Ethanol Usage in General Aviation Aircraft}, year = {2014}, abstract = {Up in the clouds and above fuels and construction materials must be very carefully selected to ensure a smooth flight and touchdown. Out of around 38,000 single and dual-engined propeller aeroplanes, roughly a third are affected by a new trend in the fuel sector that may lead to operating troubles or even emergency landings: The admixture of bio-ethanol to conventional gasoline. Experiences with these fuels may be projected to alternative mixtures containing new components.}, language = {en} } @inproceedings{NeugebauerBrutschyMeyeretal.2014, author = {Neugebauer, Georg and Brutschy, Lucas and Meyer, Ulrike and Wetzel, Susanne}, title = {Privacy-preserving multi-party reconciliation secure in the malicious model}, series = {DPM 2013, SETOP 2013: Data Privacy Management and Autonomous Spontaneous Security}, booktitle = {DPM 2013, SETOP 2013: Data Privacy Management and Autonomous Spontaneous Security}, editor = {Garcia-Alfaro, Joaquin and Lioudakis, Georgios and Cuppens-Boulahia, Nora and Foley, Simon and Fitzgerald, William M.}, publisher = {Springer}, address = {Berlin}, isbn = {978-3-642-54567-2 (Print)}, doi = {10.1007/978-3-642-54568-9_12}, pages = {178 -- 193}, year = {2014}, abstract = {The problem of fair and privacy-preserving ordered set reconciliation arises in a variety of applications like auctions, e-voting, and appointment reconciliation. While several multi-party protocols have been proposed that solve this problem in the semi-honest model, there are no multi-party protocols that are secure in the malicious model so far. In this paper, we close this gap. Our newly proposed protocols are shown to be secure in the malicious model based on a variety of novel non-interactive zero-knowledge-proofs. We describe the implementation of our protocols and evaluate their performance in comparison to protocols solving the problem in the semi-honest case.}, language = {en} }