TY - CHAP A1 - Stark, Ralf A1 - Bartel, Sebastian A1 - Ditsche, Florian A1 - Esch, Thomas T1 - Design study of a 30kN LOX/LCH4 aerospike rocket engine for lunar lander application T2 - Aerospace Europe Conference 2023 - 10th EUCASS - 9th CEAS N2 - Based on lunar lander concept EL3, various LOX/CH4 aerospike engines were studied. A distinction was made between single and cluster configurations as well as ideal and non-ideal contour concepts. It could be shown that non-ideal aerospike engines promise a significant payload gain. Y1 - 2023 N1 - Lausanne, July 9-13, 2023 ER - TY - CHAP A1 - Stark, Ralf A1 - Rieping, Carla A1 - Esch, Thomas T1 - The impact of guide tubes on flow separation in rocket nozzles T2 - Aerospace Europe Conference 2023 - 10th EUCASS - 9th CEAS N2 - Rocket engine test facilities and launch pads are typically equipped with a guide tube. Its purpose is to ensure the controlled and safe routing of the hot exhaust gases. In addition, the guide tube induces a suction that effects the nozzle flow, namely the flow separation during transient start-up and shut-down of the engine. A cold flow subscale nozzle in combination with a set of guide tubes was studied experimentally to determine the main influencing parameters. KW - Guide Tube KW - TICTOP KW - Nozzle KW - Suction Y1 - 2023 N1 - Lausanne, July 9-13, 2023 ER - TY - JOUR A1 - Schopen, Oliver A1 - Narayan, Sriram A1 - Beckmann, Marvin A1 - Najmi, Aezid-Ul-Hassan A1 - Esch, Thomas A1 - Shabani, Bahman T1 - An EIS approach to quantify the effects of inlet air relative humidity on the performance of proton exchange membrane fuel cells: a pathway to developing a novel fault diagnostic method JF - International Journal of Hydrogen Energy N2 - In this work, the effect of low air relative humidity on the operation of a polymer electrolyte membrane fuel cell is investigated. An innovative method through performing in situ electrochemical impedance spectroscopy is utilised to quantify the effect of inlet air relative humidity at the cathode side on internal ionic resistances and output voltage of the fuel cell. In addition, algorithms are developed to analyse the electrochemical characteristics of the fuel cell. For the specific fuel cell stack used in this study, the membrane resistance drops by over 39 % and the cathode side charge transfer resistance decreases by 23 % after increasing the humidity from 30 % to 85 %, while the results of static operation also show an increase of ∼2.2 % in the voltage output after increasing the relative humidity from 30 % to 85 %. In dynamic operation, visible drying effects occur at < 50 % relative humidity, whereby the increase of the air side stoichiometry increases the drying effects. Furthermore, other parameters, such as hydrogen humidification, internal stack structure, and operating parameters like stoichiometry, pressure, and temperature affect the overall water balance. Therefore, the optimal humidification range must be determined by considering all these parameters to maximise the fuel cell performance and durability. The results of this study are used to develop a health management system to ensure sufficient humidification by continuously monitoring the fuel cell polarisation data and electrochemical impedance spectroscopy indicators. KW - PEM fuel cell KW - Electrochemical impedance spectroscopy KW - Relative air humidity KW - Active humidity control KW - Impedance analysis Y1 - 2024 SN - 0360-3199 (print) U6 - https://doi.org/10.1016/j.ijhydene.2024.01.218 SN - 1879-3487 (online) VL - 58 IS - 8 SP - 1302 EP - 1315 PB - Elsevier CY - Amsterdam ER - TY - GEN A1 - Machado, Patricia Almeida A1 - Dahmann, Peter A1 - Keimer, Jona A1 - Saretzki, Charlotte A1 - Stübing, Felix A1 - Küpper, Thomas T1 - Stress profile and individual workload monitoring in general aviation pilots – an experiment’s setting T2 - 23. Annual Meeting of the German Society of Travel Medicine, Coburg, 18.-19.9.2020 Y1 - 2020 U6 - https://doi.org/10.55225/hppa.156 ER - TY - CHAP A1 - Langohr, Philipp A1 - Bung, Daniel Bernhard A1 - Crookston, Brian M. ED - Ortega-Sánchez, Miguel T1 - Hybrid investigation of labyrinth weirs: Discharge capacity and energy dissipation T2 - Proceedings of the 39th IAHR World Congress N2 - The replacement of existing spillway crests or gates with labyrinth weirs is a proven techno-economical means to increase the discharge capacity when rehabilitating existing structures. However, additional information is needed regarding energy dissipation of such weirs, since due to the folded weir crest, a three-dimensional flow field is generated, yielding more complex overflow and energy dissipation processes. In this study, CFD simulations of labyrinth weirs were conducted 1) to analyze the discharge coefficients for different discharges to compare the Cd values to literature data and 2) to analyze and improve energy dissipation downstream of the structure. All tests were performed for a structure at laboratory scale with a height of approx. P = 30.5 cm, a ratio of the total crest length to the total width of 4.7, a sidewall angle of 10° and a quarter-round weir crest shape. Tested headwater ratios were 0.089 ≤ HT/P ≤ 0.817. For numerical simulations, FLOW-3D Hydro was employed, solving the RANS equations with use of finite-volume method and RNG k-ε turbulence closure. In terms of discharge capacity, results were compared to data from physical model tests performed at the Utah Water Research Laboratory (Utah State University), emphasizing higher discharge coefficients from CFD than from the physical model. For upstream heads, some discrepancy in the range of ± 1 cm between literature, CFD and physical model tests was identified with a discussion regarding differences included in the manuscript. For downstream energy dissipation, variable tailwater depths were considered to analyze the formation and sweep-out of a hydraulic jump. It was found that even for high discharges, relatively low downstream Froude numbers were obtained due to high energy dissipation involved by the three-dimensional flow between the sidewalls. The effects of some additional energy dissipation devices, e.g. baffle blocks or end sills, were also analyzed. End sills were found to be non-effective. However, baffle blocks with different locations may improve energy dissipation downstream of labyrinth weirs. Y1 - 2022 SN - 978-90-832612-1-8 U6 - https://doi.org/10.3850/IAHR-39WC252171192022738 SN - 2521-7119 (print) SN - 2521-716X (online) N1 - 39th IAHR World Congress, 19. - 24. Juni 2022, Granada SP - 2313 EP - 2318 PB - International Association for Hydro-Environment Engineering and Research (IAHR) CY - Madrid ER - TY - CHAP A1 - Crookston, Brian M. A1 - Bung, Daniel Bernhard ED - Ortega-Sánchez, Miguel T1 - Application of RGB-D cameras in hydraulic laboratory studies T2 - Proceedings of the 39th IAHR World Congress N2 - Non-intrusive measuring techniques have attained a lot of interest in relation to both hydraulic modeling and prototype applications. Complimenting acoustic techniques, significant progress has been made for the development of new optical methods. Computer vision techniques can help to extract new information, e. g. high-resolution velocity and depth data, from videos captured with relatively inexpensive, consumer-grade cameras. Depth cameras are sensors providing information on the distance between the camera and observed features. Currently, sensors with different working principles are available. Stereoscopic systems reference physical image features (passive system) from two perspectives; in order to enhance the number of features and improve the results, a sensor may also estimate the disparity from a detected light to its original projection (active stereo system). In the current study, the RGB-D camera Intel RealSense D435, working on such stereo vision principle, is used in different, typical hydraulic modeling applications. All tests have been conducted at the Utah Water Research Laboratory. This paper will demonstrate the performance and limitations of the RGB-D sensor, installed as a single camera and as camera arrays, applied to 1) detect the free surface for highly turbulent, aerated hydraulic jumps, for free-falling jets and for an energy dissipation basin downstream of a labyrinth weir and 2) to monitor local scours upstream and downstream of a Piano Key Weir. It is intended to share the authors’ experiences with respect to camera settings, calibration, lightning conditions and other requirements in order to promote this useful, easily accessible device. Results will be compared to data from classical instrumentation and the literature. It will be shown that even in difficult application, e. g. the detection of a highly turbulent, fluctuating free-surface, the RGB-D sensor may yield similar accuracy as classical, intrusive probes. Y1 - 2022 SN - 978-90-832612-1-8 U6 - https://doi.org/10.3850/IAHR-39WC252171192022964 SN - 2521-7119 (print) SN - 2521-716X (online) N1 - 39th IAHR World Congress, 19. - 24. Juni 2022, Granada SP - 5127 EP - 5133 PB - International Association for Hydro-Environment Engineering and Research (IAHR) CY - Madrid ER - TY - CHAP A1 - Hülsen, Benjamin A1 - Mulsow, Niklas A. A1 - Dabrowski, Adam A1 - Brinkmann, Wiebke A1 - Gützlaff, Joel A1 - Spies, Leon A1 - Czupalla, Markus A1 - Kirchner, Frank T1 - Towards an autonomous micro rover with night survivability for lunar exploration T2 - Proceedings of the 74th International Astronautical Congress N2 - In Europe, efforts are underway to develop key technologies that can be used to explore the Moon and to exploit the resources available. This includes technologies for in-situ resource utilization (ISRU), facilitating the possibility of a future Moon Village. The Moon is the next step for humans and robots to exploit the use of available resources for longer term missions, but also for further exploration of the solar system. A challenge for effective exploration missions is to achieve a compact and lightweight robot to reduce launch costs and open up the possibility of secondary payload options. Current micro rover concepts are primarily designed to last for one day of solar illumination and show a low level of autonomy. Extending the lifetime of the system by enabling survival of the lunar night and implementing a high level of autonomy will significantly increase potential mission applications and the operational range. As a reference mission, the deployment of a micro rover in the equatorial region of the Moon is being considered. An overview of mission parameters and a detailed example mission sequence is given in this paper. The mission parameters are based on an in-depth study of current space agency roadmaps, scientific goals, and upcoming flight opportunities. Furthermore, concepts of the ongoing international micro rover developments are analyzed along with technology solutions identified for survival of lunar nights and a high system autonomy. The results provide a basis of a concise requirements set-up to allow dedicated system developments and qualification measures in the future. Y1 - 2023 N1 - 74. International Astronautical Congress (IAC-2023), October 2-6 2023, Baku, Azerbaijan PB - dfki ER - TY - CHAP A1 - Mulsow, Niklas A. A1 - Hülsen, Benjamin A1 - Gützlaff, Joel A1 - Spies, Leon A1 - Bresser, Andreas A1 - Dabrowski, Adam A1 - Czupalla, Markus A1 - Kirchner, Frank T1 - Concept and design of an autonomous micro rover for long term lunar exploration T2 - Proceedings of the 74th International Astronautical Congress N2 - Research on robotic lunar exploration has seen a broad revival, especially since the Google Lunar X-Prize increasingly brought private endeavors into play. This development is supported by national agencies with the aim of enabling long-term lunar infrastructure for in-situ operations and the establishment of a moon village. One challenge for effective exploration missions is developing a compact and lightweight robotic rover to reduce launch costs and open the possibility for secondary payload options. Existing micro rovers for exploration missions are clearly limited by their design for one day of sunlight and their low level of autonomy. For expanding the potential mission applications and range of use, an extension of lifetime could be reached by surviving the lunar night and providing a higher level of autonomy. To address this objective, the paper presents a system design concept for a lightweight micro rover with long-term mission duration capabilities, derived from a multi-day lunar mission scenario at equatorial regions. Technical solution approaches are described, analyzed, and evaluated, with emphasis put on the harmonization of hardware selection due to a strictly limited budget in dimensions and power. Y1 - 2023 N1 - 74. International Astronautical Congress (IAC-2023), October 2-6 2023, Baku, Azerbaijan PB - dfki CY - Saarbrücken ER - TY - INPR A1 - Schmülling, Max A1 - Gützlaff, Joel A1 - Czupalla, Markus T1 - A thermal simulation environment for moving objects on the lunar surface N2 - This paper presents a thermal simulation environment for moving objects on the lunar surface. The goal of the thermal simulation environment is to enable the reliable prediction of the temperature development of a given object on the lunar surface by providing the respective heat fluxes for a mission on a given travel path. The user can import any object geometry and freely define the path that the object should travel. Using the path of the object, the relevant lunar surface geometry is imported from a digital elevation model. The relevant parts of the lunar surface are determined based on distance to the defined path. A thermal model of these surface sections is generated, consisting of a porous layer on top and a denser layer below. The object is moved across the lunar surface, and its inclination is adapted depending on the slope of the terrain below it. Finally, a transient thermal analysis of the object and its environment is performed at several positions on its path and the results are visualized. The paper introduces details on the thermal modeling of the lunar surface, as well as its verification. Furthermore, the structure of the created software is presented. The robustness of the environment is verified with the help of sensitivity studies and possible improvements are presented. KW - Dynamic modeling KW - Thermal analysis KW - ESATAN-TMS KW - Lunar Surface KW - Thermal Model Y1 - 2024 U6 - https://doi.org/10.21203/rs.3.rs-3902363/v1 ER - TY - CHAP A1 - Kohlberger, David-Sharif A1 - Wild, Dominik A1 - Kasper, Stefan A1 - Czupalla, Markus T1 - Modeling and analyses of a thermal passively stabilized LEO/GEO star tracker with embedded phase change material applying the Infused Thermal Solutions (ITS) method T2 - ICES202: Satellite, Payload, and Instrument Thermal Control N2 - Phase change materials offer a way of storing excess heat and releasing it when it is needed. They can be utilized as a method to control thermal behavior without the need for additional energy. This work focuses on exploring the potential of using phase change materials to passively control the thermal behavior of a star tracker by infusing it with a fitting phase change material. Based on the numerical model of the star trackers thermal behavior using ESATAN-TMS without implemented phase change material, a fitting phase change material for selected orbits is chosen and implemented in the thermal model. The altered thermal behavior of the numerical model after the implementation is analyzed for different amounts of the chosen phase change materials using an ESATAN-based subroutine developed by the FH Aachen. The PCM-modelling-subroutine is explained in the paper ICES-2021-110. The results show that an increasing amount of phase change material increasingly damps temperature oscillations. Using an integral part structure some of the mass increase can be compensated. KW - passive thermal control KW - PCM KW - star tracker KW - Infused Thermal Solutions KW - GEO KW - LEO Y1 - 2021 N1 - 50th International Conference on Environmental Systems, 12-15 July 2021, held virtually PB - Texas Tech University CY - Lubbock, Tex. ER - TY - CHAP A1 - Wild, Dominik A1 - Czupalla, Markus A1 - Förstner, Roger T1 - Modeling, prediction and test of additive manufactured integral structures with embedded lattice and phase change material applying Infused Thermal Solutions (ITS) T2 - ICES104: Advances in Thermal Control Technology N2 - Infused Thermal Solutions (ITS) introduces a method for passive thermal control to stabilize structural components thermally without active heating and cooling systems, but with phase change material (PCM) for thermal energy storage (TES), in combination with lattice - both embedded in additive manufactured functional structures. In this ITS follow-on paper a thermal model approach and associated predictions are presented, related on the ITS functional breadboards developed at FH Aachen. Predictive TES by PCM is provided by a specially developed ITS PCM subroutine, which is applicable in ESATAN. The subroutine is based on the latent heat storage (LHS) method to numerically embed thermo-physical PCM behavior. Furthermore, a modeling approach is introduced to numerically consider the virtual PCM/lattice nodes within the macro-encapsulated PCM voids of the double wall ITS design. Related on these virtual nodes, in-plane and out-of-plane conductive links are defined. The recent additive manufactured ITS breadboard series are thermally cycled in the thermal vacuum chamber, both with and without embedded PCM. Related on breadboard hardware tests, measurement results are compared with predictions and are subsequently correlated. The results of specific simulations and measurements are presented. Recent predictive results of star tracker analyses are also presented in ICES-2021-106, based on this ITS PCM subroutine. KW - latent heat KW - thermo-physical KW - lattice KW - ESATAN KW - subroutine KW - PCM KW - ITS Y1 - 2021 N1 - 50th International Conference on Environmental Systems, 12-15 July 2021, held virtually PB - Texas Tech University CY - Lubbock, Tex. ER - TY - JOUR A1 - Schopen, Oliver A1 - Shah, Neel A1 - Esch, Thomas A1 - Shabani, Bahman T1 - Critical quantitative evaluation of integrated health management methods for fuel cell applications JF - International Journal of Hydrogen Energy N2 - Online fault diagnostics is a crucial consideration for fuel cell systems, particularly in mobile applications, to limit downtime and degradation, and to increase lifetime. Guided by a critical literature review, in this paper an overview of Health management systems classified in a scheme is presented, introducing commonly utilised methods to diagnose FCs in various applications. In this novel scheme, various Health management system methods are summarised and structured to provide an overview of existing systems including their associated tools. These systems are classified into four categories mainly focused on model-based and non-model-based systems. The individual methods are critically discussed when used individually or combined aimed at further understanding their functionality and suitability in different applications. Additionally, a tool is introduced to evaluate methods from each category based on the scheme presented. This tool applies the technique of matrix evaluation utilising several key parameters to identify the most appropriate methods for a given application. Based on this evaluation, the most suitable methods for each specific application are combined to build an integrated Health management system. KW - Fuel cell KW - Health management system KW - Online diagnostic KW - Fault detection KW - Non-model-based Evaluation Y1 - 2024 U6 - https://doi.org/10.1016/j.ijhydene.2024.05.156 SN - 0360-3199 VL - 70 SP - 370 EP - 388 PB - Elsevier CY - Amsterdam ER - TY - JOUR A1 - Czupalla, Markus T1 - Ein Garten im Weltraum JF - Spektrum der Wissenschaft Y1 - 2017 PB - Spektrum-der-Wiss.-Verl.-Ges. CY - Heidelberg ER - TY - GEN A1 - Eccleston, Paul A1 - Drummond, Rachel A1 - Middleton, Kevin A1 - Bishop, Georgia A1 - Caldwell, Andrew A1 - Desjonqueres, Lucile A1 - Tosh, Ian A1 - Cann, Nick A1 - Crook, Martin A1 - Hills, Matthew A1 - Pearson, Chris A1 - Simpson, Caroline A1 - Stamper, Richard A1 - Tinetti, Giovanna A1 - Pascale, Enzo A1 - Swain, Mark A1 - Holmes, Warren A. A1 - Wong, Andre A1 - Puig, Ludovic A1 - Pilbratt, Göran A1 - Linder, Martin A1 - Boudin, Nathalie A1 - Ertel, Hanno A1 - Gambicorti, Lisa A1 - Halain, Jean-Philippe A1 - Pace, Emanuele A1 - Vilardell, Francesc A1 - Gómez, José M. A1 - Colomé, Josep A1 - Amiaux, Jérôme A1 - Cara, Christophe A1 - Berthe, Michel A1 - Moreau, Vincent A1 - Morgante, Gianluca A1 - Malaguti, Giuseppe A1 - Alonso, Gustavo A1 - Álvarez, Javier P. A1 - Ollivier, Marc A1 - Philippon, Anne A1 - Hellin, Marie-Laure A1 - Roose, Steve A1 - Frericks, Martin A1 - Krijger, Matthijs A1 - Rataj, Miroslaw A1 - Wawer, Piotr A1 - Skup, Konrad A1 - Sobiecki, Mateusz A1 - Christian Jessen, Niels A1 - Møller Pedersen, Søren A1 - Hargrave, Peter A1 - Griffin, Matt A1 - Ottensamer, Roland A1 - Hunt, Thomas A1 - Rust, Duncan A1 - Saleh, Aymen A1 - Winter, Berend A1 - Focardi, Mauro A1 - Da Deppo, Vania A1 - Zuppella, Paola A1 - Czupalla, Markus ED - Lystrup, Makenzie ED - Perrin, Marshall D. ED - Batalha, Natalie ED - Siegler, Nicholas ED - Tong, Edward C. T1 - The ARIEL payload: A technical overview T2 - Space Telescopes and Instrumentation 2020: Optical, Infrared, and Millimeter Wave N2 - The Atmospheric Remote-Sensing Infrared Exoplanet Large-survey, ARIEL, has been selected to be the next (M4) medium class space mission in the ESA Cosmic Vision programme. From launch in 2028, and during the following 4 years of operation, ARIEL will perform precise spectroscopy of the atmospheres of ~1000 known transiting exoplanets using its metre-class telescope. A three-band photometer and three spectrometers cover the 0.5 µm to 7.8 µm region of the electromagnetic spectrum. This paper gives an overview of the mission payload, including the telescope assembly, the FGS (Fine Guidance System) - which provides both pointing information to the spacecraft and scientific photometry and low-resolution spectrometer data, the ARIEL InfraRed Spectrometer (AIRS), and other payload infrastructure such as the warm electronics, structures and cryogenic cooling systems. KW - Exoplanet KW - Spectroscopy KW - Transit KW - Atmospheres KW - Payload Y1 - 2020 U6 - https://doi.org/10.1117/12.2561478 N1 - Space Telescopes and Instrumentation 2020: Optical, Infrared, and Millimeter Wave, 14–22 December 2020, Online Only, United States VL - 11443 SP - 114430Z PB - SPIE CY - Washington ER - TY - GEN A1 - Reiswich, Martin A1 - Brandt, Hannes A1 - Czupalla, Markus T1 - Passive thermal control by integration of phase change material into additively manufactured structures T2 - E2. 47th Student conference N2 - Optical Instruments require an extremely stable thermal surrounding to prevent loss of data quality by misalignments of the instrument components resulting from material deformation due to temperature f luctuations (e.g. from solar intrusion). Phase Change Material (PCM) can be applied as a thermal damper to achieve a more uniform temperature distribution. The challenge of this method is, among others, the integration of PCM into affected areas. If correctly designed, incoming heat is latently absorbed during phase change of the PCM, i.e. the temperature of a structure remains almost constant. In a cold phase, the heat during phase change is released again latently until the PCM returns to its original state of aggregation. Thus, the structure is thermally stabilized. At FH Aachen– University of Applied Sciences research is conducted to apply PCM directly into the structures of affected components (baffles, optical benches, electronic boxes, etc.). Through the application of Additive Manufacturing, the necessary voids are directly printed into these structures and filled later with PCM. Additive Manufacturing enables complex structures that would not have been possible with conservative manufacturing methods. A corresponding Breadboard was developed and manufactured by Selective Laser Melting (SLM). The current state of research includes the handling and analysis of the Breadboard, tests and a correlation of the thermal model. The results have shown analytically and practically that it is possible to use PCM as an integral part of the structure as a thermal damper. The results serve as a basis for the further development of the technology, which should maximize performance and enable the integration of PCM into much more complex structures. Y1 - 2019 N1 - 70th International Astronautical Congress, 21. - 25. Oktober 2019, Washington D.C., United States ER - TY - GEN A1 - Gamgami, Farid A1 - Czupalla, Markus A1 - Garcia, Antonio A1 - Agnolon, David T1 - From planetary transits to spacecraft design: achieving PLATO’s pointing performance T2 - A7. Symposium on technological Requirement for future space astronomy and solar-system science missions N2 - In the last decades, several hundred exoplanets could be detected thanks to space-based observatories, namely CNES’ COROT and NASA’s Kepler. To expand this quest ESA plans to launch CHEOPS as the f irst small class mission in the cosmic visions program (S1) and PLATO as the 3rd medium class mission, so called M3 . PLATO’s primary objective is the detection of Earth like Exoplanets orbiting solar type stars in the habitable zone and characterisation of their bulk properties. This is possible by precise lightcurve measurement via 34 cameras. That said it becomes obvious that accurate pointing is key to achieve the required signal to noise ratio for positive transit detection. The paper will start with a comprehensive overview of PLATO’s mission objectives and mission architecture. Hereafter, special focus will be devoted to PLATO’s pointing requirements. Understanding the very nature of PLATO’s pointing requirements is essential to derive a design baseline to achieve the required performance. The PLATO frequency domain is of particular interest, ranging from 40 mHz to 3 Hz. Due to the very different time-scales involved, the spectral pointing requirement is decomposed into a high frequency part dominated by the attitude control system and the low frequency part dominated by the thermo-elastic properties of the spacecraft’s configuration. Both pose stringent constraints on the overall design as well as technology properties to comply with the derived requirements and thus assure a successful mission. Y1 - 2016 N1 - 67th International Astronautical Congress, 26. - 30. September 2016, Guadalajara, Mexico ER - TY - CHAP A1 - Bung, Daniel Bernhard A1 - Langohr, Phillip A1 - Waldenberger, Lisa ED - Habersack, Helmut ED - Tritthart, Michael T1 - Influence of cycle number in CFD studies of labyrinth weirs T2 - Proceedings of the 40th IAHR World Congress (Vienna, 2023) N2 - The major advantage of labyrinth weirs over linear weirs is hydraulic efficiency. In hydraulic modeling efforts, this strength contrasts with limited pump capacity as well as limited computational power for CFD simulations. For the latter, reducing the number of investigated cycles can significantly reduce necessary computational time. In this study, a labyrinth weir with different cycle numbers was investigated. The simulations were conducted in FLOW-3D HYDRO as a Large Eddy Simulation. With a mean deviation of 1.75 % between simulated discharge coefficients and literature design equations, a reasonable agreement was found. For downstream conditions, overall consistent results were observed as well. However, the orientation of labyrinth weirs with a single cycle should be chosen carefully under consideration of the individual research purpose. KW - CFD KW - Large Eddy Simulation KW - Labyfrinth weirs Y1 - 2023 SN - 978-90-833476-1-5 U6 - https://doi.org/10.3850/978-90-833476-1-5_iahr40wc-p0531-cd SN - L 2521-7119 (online) N1 - Vienna, Austria, from August 21 to 25, 2023 PB - International Association for Hydro-Environment Engineering and Research (IAHR) CY - Madrid ER - TY - JOUR A1 - Droop, Philipp A1 - Chen, Shaohuang A1 - Radford, Melissa J. A1 - Paulßen, Elisabeth A1 - Gates, Byron D. A1 - Reilly, Raymond M. A1 - Radchenko, Valery A1 - Hoehr, Cornelia T1 - Synthesis of 197m/gHg labelled gold nanoparticles for targeted radionuclide therapy JF - Radiochimica Acta N2 - Meitner-Auger-electron emitters have a promising potential for targeted radionuclide therapy of cancer because of their short range and the high linear energy transfer of Meitner-Auger-electrons (MAE). One promising MAE candidate is 197m/gHg with its half-life of 23.8 h and 64.1 h, respectively, and high MAE yield. Gold nanoparticles (AuNPs) that are labelled with 197m/gHg could be a helpful tool for radiation treatment of glioblastoma multiforme when infused into the surgical cavity after resection to prevent recurrence. To produce such AuNPs, 197m/gHg was embedded into pristine AuNPs. Two different syntheses were tested starting from irradiated gold containing trace amounts of 197m/gHg. When sodium citrate was used as reducing agent, no 197m/gHg labelled AuNPs were formed, but with tannic acid, 197m/gHg labeled AuNPs were produced. The method was optimized by neutralizing the pH (pH = 7) of the Au/197m/gHg solution, which led to labelled AuNPs with a size of 12.3 ± 2.0 nm as measured by transmission electron microscopy. The labelled AuNPs had a concentration of 50 μg (gold)/mL with an activity of 151 ± 93 kBq/mL (197gHg, time corrected to the end of bombardment). KW - 197m/gHg KW - Gold nanoparticle (AuNP) KW - Meitner-Auger-electron (MAE) KW - Targeted radionuclide therapy (TRT) Y1 - 2023 U6 - https://doi.org/10.1515/ract-2023-0144 SN - 2193-3405 VL - 111 IS - 10 SP - 773 EP - 779 PB - De Gruyter CY - Berlin [u.a.] ER - TY - JOUR A1 - Mues genannt Koers, Lucas A1 - McNeil, S. W. A1 - Radchenko, V. A1 - Paulßen, Elisabeth A1 - Hoehr, Cornelia T1 - Production of Co-58m in a siphon-style liquid target on a medical cyclotron N2 - We present the production of 58mCo on a small, 13 MeV medical cyclotron utilizing a siphon style liquid target system. Different concentrated iron(III)-nitrate solutions of natural isotopic distribution were irradiated at varying initial pressures and subsequently separated by solid phase extraction chromatography. The radio cobalt (58m/gCo and 56Co) was successfully produced with saturation activities of (0.35 ± 0.03) MBq μA−1 for 58mCo with a separation recovery of (75 ± 2) % of cobalt after one separation step utilizing LN-resin. Y1 - 2023 U6 - https://doi.org/10.1016/j.apradiso.2023.110734 SN - 0969-8043 VL - 195 IS - Art. 110734 PB - Elsevier CY - Amsterdam ER - TY - JOUR A1 - Mues genannt Koers, Lucas A1 - Prevost, David A1 - Paulßen, Elisabeth A1 - Hoehr, Cornelia T1 - Density reduction effects on the production of [11C]CO2 in Nb-body targets on a medical cyclotron N2 - Medical isotope production of 11C is commonly performed in gaseous targets. The power deposition of the proton beam during the irradiation decreases the target density due to thermodynamic mixing and can cause an increase of penetration depth and divergence of the proton beam. In order to investigate the difference how the target-body length influences the operation conditions and the production yield, a 12 cm and a 22 cm Nb-target body containing N2/O2 gas were irradiated using a 13 MeV proton cyclotron. It was found that the density reduction has a large influence on the pressure rise during irradiation and the achievable radioactive yield. The saturation activity of [11C]CO2 for the long target (0.083 Ci/μA) is about 10% higher than in the short target geometry (0.075 Ci/μA). Y1 - 2023 U6 - https://doi.org/10.1016/j.apradiso.2023.110911 VL - 199 IS - Art. 110911 PB - Elsevier CY - Amsterdam ER - TY - THES A1 - Bung, Daniel Bernhard T1 - Imaging techniques for investigation of free-surface flows in hydraulic laboratories N2 - This thesis aims at the presentation and discussion of well-accepted and new imaging techniques applied to different types of flow in common hydraulic engineering environments. All studies are conducted in laboratory conditions and focus on flow depth and velocity measurements. Investigated flows cover a wide range of complexity, e.g. propagation of waves, dam-break flows, slightly and fully aerated spillway flows as well as highly turbulent hydraulic jumps. Newimagingmethods are compared to different types of sensorswhich are frequently employed in contemporary laboratory studies. This classical instrumentation as well as the general concept of hydraulic modeling is introduced to give an overview on experimental methods. Flow depths are commonly measured by means of ultrasonic sensors, also known as acoustic displacement sensors. These sensors may provide accurate data with high sample rates in case of simple flow conditions, e.g. low-turbulent clear water flows. However, with increasing turbulence, higher uncertainty must be considered. Moreover, ultrasonic sensors can provide point data only, while the relatively large acoustic beam footprint may lead to another source of uncertainty in case of relatively short, highly turbulent surface fluctuations (ripples) or free-surface air-water flows. Analysis of turbulent length and time scales of surface fluctuations from point measurements is also difficult. Imaging techniques with different dimensionality, however, may close this gap. It is shown in this thesis that edge detection methods (known from computer vision) may be used for two-dimensional free-surface extraction (i.e. from images taken through transparant sidewalls in laboratory flumes). Another opportunity in hydraulic laboratory studies comes with the application of stereo vision. Low-cost RGB-D sensors can be used to gather instantaneous, three-dimensional free-surface elevations, even in flows with very high complexity (e.g. aerated hydraulic jumps). It will be shown that the uncertainty of these methods is of similar order as for classical instruments. Particle Image Velocimetry (PIV) is a well-accepted and widespread imaging technique for velocity determination in laboratory conditions. In combination with high-speed cameras, PIV can give time-resolved velocity fields in 2D/3D or even as volumetric flow fields. PIV is based on a cross-correlation technique applied to small subimages of seeded flows. The minimum size of these subimages defines the maximum spatial resolution of resulting velocity fields. A derivative of PIV for aerated flows is also available, i.e. the so-called Bubble Image Velocimetry (BIV). This thesis emphasizes the capacities and limitations of both methods, using relatively simple setups with halogen and LED illuminations. It will be demonstrated that PIV/BIV images may also be processed by means of Optical Flow (OF) techniques. OF is another method originating from the computer vision discipline, based on the assumption of image brightness conservation within a sequence of images. The Horn-Schunck approach, which has been first employed to hydraulic engineering problems in the studies presented herein, yields dense velocity fields, i.e. pixelwise velocity data. As discussed hereinafter, the accuracy of OF competes well with PIV for clear-water flows and even improves results (compared to BIV) for aerated flow conditions. In order to independently benchmark the OF approach, synthetic images with defined turbulence intensitiy are used. Computer vision offers new opportunities that may help to improve the understanding of fluid mechanics and fluid-structure interactions in laboratory investigations. In prototype environments, it can be employed for obstacle detection (e.g. identification of potential fish migration corridors) and recognition (e.g. fish species for monitoring in a fishway) or surface reconstruction (e.g. inspection of hydraulic structures). It can thus be expected that applications to hydraulic engineering problems will develop rapidly in near future. Current methods have not been developed for fluids in motion. Systematic future developments are needed to improve the results in such difficult conditions. Y1 - 2023 U6 - https://doi.org/10.25926/BUW/0-172 ER - TY - JOUR A1 - Kleefeld, Andreas A1 - Pieronek, J. T1 - Elastic transmission eigenvalues and their computation via the method of fundamental solutions JF - Applicable Analysis N2 - A stabilized version of the fundamental solution method to catch ill-conditioning effects is investigated with focus on the computation of complex-valued elastic interior transmission eigenvalues in two dimensions for homogeneous and isotropic media. Its algorithm can be implemented very shortly and adopts to many similar partial differential equation-based eigenproblems as long as the underlying fundamental solution function can be easily generated. We develop a corroborative approximation analysis which also implicates new basic results for transmission eigenfunctions and present some numerical examples which together prove successful feasibility of our eigenvalue recovery approach. KW - elastic scattering KW - method of fundamental solutions KW - Interior transmission eigenvalues Y1 - 2020 U6 - https://doi.org/10.1080/00036811.2020.1721473 SN - 1563-504X VL - 100 IS - 16 SP - 3445 EP - 3462 PB - Taylore & Francis CY - London ER - TY - CHAP A1 - Mayntz, Joscha A1 - Keimer, Jona A1 - Dahmann, Peter A1 - Hille, Sebastian A1 - Stumpf, Eike A1 - Fisher, Alex A1 - Dorrington, Graham T1 - Electrical Drive and Regeneration in General Aviation Flight with Propellers T2 - Deutscher Luft- und Raumfahrtkongress 2020 N2 - Electric flight has the potential for a more sustainable and energy-saving way of aviation compared to fossil fuel aviation. The electric motor can be used as a generator inflight to regenerate energy during descent. Three different approaches to regenerating with electric propeller powertrains are proposed in this paper. The powertrain is to be set up in a wind tunnel to determine the propeller efficiency in both working modes as well as the noise emissions. Furthermore, the planned flight tests are discussed. In preparation for these tests, a yaw stability analysis is performed with the result that the aeroplane is controllable during flight and in the most critical failure case. The paper shows the potential for inflight regeneration and addresses the research gaps in the dual role of electric powertrains for propulsion and regeneration of general aviation aircraft. KW - Propeller Aerodynamics KW - Flight Tests KW - Flight Mechanics KW - Electrical Flight KW - Inflight Regeneration, Recuperation Y1 - 2022 U6 - https://doi.org/10.25967/530100 N1 - Deutscher Luft- und Raumfahrtkongress 2020, 1. - 3. September 2020, Online PB - DGLR CY - Bonn ER - TY - GEN A1 - Mayntz, Joscha A1 - Keimer, Jona A1 - Tegtmeyer, Philipp A1 - Dahmann, Peter A1 - Hille, Sebastian A1 - Stumpf, Eike A1 - Fisher, Alex A1 - Dorrington, Graham T1 - Aerodynamic Investigation on Efficient Inflight Transition of a Propeller from Propulsion to Regeneration Mode T2 - AIAA SCITECH 2022 Forum N2 - This paper discusses a new way of inflight power regeneration for electric or hybrid-electric driven general aviation aircraft with one powertrain for both configurations. Three different approaches for the shift from propulsion to regeneration mode are analyzed. Numerical cal-culation and wind tunnel results are compared and show the highest regeneration potential for the "Windmill" approach, where the propeller blades are flipped, and rotation is reversed. A combination of all regeneration approaches for a realistic flight mission is discussed. Y1 - 2021 U6 - https://doi.org/10.2514/6.2022-0546 N1 - AIAA SCITECH 2022 Forum, January 3-7, 2022, San Diego, CA & Virtual PB - AIAA CY - Reston, Va. ER - TY - JOUR A1 - Saretzki, Charlotte A1 - Bergmann, Ole A1 - Dahmann, Peter A1 - Janser, Frank A1 - Keimer, Jona A1 - Machado, Patricia A1 - Morrison, Audry A1 - Page, Henry A1 - Pluta, Emil A1 - Stübing, Felix A1 - Küpper, Thomas T1 - Are small airplanes safe with regards to COVID-19 transmission? JF - Journal of Travel Medicine Y1 - 2021 U6 - https://doi.org/10.1093/jtm/taab105 SN - 1708-8305 VL - 28 IS - 7 PB - Oxford University Press CY - Oxford ER - TY - CHAP A1 - Treuling, Clemens A1 - Czarnecki, Christian A1 - Wolf, Martin T1 - Projekt WiLMo – Wirtschaftsinformatik Lehr- und Lernmodule T2 - Angewandte Forschung in der Wirtschaftsinformatik 2023 : Tagungsband zur 36. AKWI-Jahrestagung N2 - Die potenziellen Auswirkungen der Digitalisierung auf die Lehre sind seit langem Gegenstand ausführlicher Diskussionen innerhalb der Wirtschaftsinformatik (WI) (z. B. in Auth et al. 2021, Barton et al. 2019, Klotz et al. 2019). Nicht zuletzt der in nahezu allen Wirtschaftszweigen bestehende Mangel an qualifizierten Fachkräften lenkt den Diskurs auf einen verbesserten Zugang zu Bildung und gleichen Bildungschancen. Aus dieser Vision heraus und dem Schub der Digitalisierung entstehen Bildungskonzepte wie Open Educational Resources (OER), die gesellschaftlichen Problemen, wie dem des Fachkräftemangels, entgegenwirken sollen. Im Rahmen dieses Kurzbeitrags wird das Projekt WiLMo - "Wirtschaftsinformatik Lehr- und Lernmodule" vorgestellt. WiLMo wird im Rahmen von OERContent.nrw unter Beteiligung von sechs Hochschulen entwickelt und gefördert. Alle Projektbeteiligten arbeiten gemeinsam daran, einheitliche digitale Lehr- und Lernmaterialien im OER-Format für die Kernmodule der Wirtschaftsinformatik zu entwickeln und in garantiert hoher Qualität zur Verfügung zu stellen. KW - Wirtschaftsinformatik KW - Open Educational Resources (OER) KW - WiLMo Y1 - 2023 N1 - 36. AKWI-Jahrestagung, 11.09.2023 bis 13.09.2023, ausgerichtet von der Technischen Hochschule Wildau SP - 161 EP - 169 ER - TY - GEN A1 - Keimer, Jona A1 - Girbig, Leo A1 - Mayntz, Joscha A1 - Tegtmeyer, Philipp A1 - Wendland, Frederik A1 - Dahman, Peter A1 - Fisher, Alex A1 - Dorrington, Graham T1 - Flight mission optimization for eco-efficiency in consideration of electric regeneration and atmospheric conditions T2 - AIAA AVIATION 2022 Forum N2 - The development and operation of hybrid or purely electrically powered aircraft in regional air mobility is a significant challenge for the entire aviation sector. This technology is expected to lead to substantial advances in flight performance, energy efficiency, reliability, safety, noise reduction, and exhaust emissions. Nevertheless, any consumed energy results in heat or carbon dioxide emissions and limited electric energy storage capabilities suppress commercial use. Therefore, the significant challenges to achieving eco-efficient aviation are increased aircraft efficiency, the development of new energy storage technologies, and the optimization of flight operations. Two major approaches for higher eco-efficiency are identified: The first one, is to take horizontal and vertical atmospheric motion phenomena into account. Where, in particular, atmospheric waves hold exciting potential. The second one is the use of the regeneration ability of electric aircraft. The fusion of both strategies is expected to improve efficiency. The objective is to reduce energy consumption during flight while not neglecting commercial usability and convenient flight characteristics. Therefore, an optimized control problem based on a general aviation class aircraft has to be developed and validated by flight experiments. The formulated approach enables a development of detailed knowledge of the potential and limitations of optimizing flight missions, considering the capability of regeneration and atmospheric influences to increase efficiency and range. Y1 - 2022 U6 - https://doi.org/10.2514/6.2022-4118 N1 - AIAA AVIATION 2022 Forum, June 27-July 1, 2022 Chicago, IL & Virtual PB - AIAA CY - Reston, Va. ER - TY - BOOK A1 - Czarnecki, Christian ED - Czarnecki, Christian ED - Lübbe, Alexander ED - Meister, Vera G. ED - Müller, Christian ED - Steglich, Mike ED - Walther, Mathias T1 - Angewandte Forschung in der Wirtschaftsinformatik 2023 : Tagungsband zur 36. AKWI-Jahrestagung N2 - Beiträge der Fachtagung „Angewandte Forschung in der Wirtschaftsinformatik – Zukunft gestalten“ im Rahmen der 36. Jahrestagung des Arbeitskreises Wirtschaftsinformatik an Hochschulen für Angewandte Wissenschaften (AKWI) vom 11. bis 13.09.2023 an der Technischen Hochschule Wildau Y1 - 2023 U6 - https://doi.org/10.15771/1794 N1 - 36. AKWI-Jahrestagung, 11.09.2023 bis 13.09.2023, ausgerichtet von der Technischen Hochschule Wildau ER - TY - JOUR A1 - Bung, Daniel Bernhard T1 - Kamerabasierte Fließtiefen- und Geschwindigkeitsmessungen JF - Wasserwirtschaft N2 - In der wasserbaulichen Forschung werden neben klassischen Messinstrumenten zunehmend kamerabasierte Verfahren genutzt. Diese erlauben neben der Bestimmung von Fließgeschwindigkeiten auch die Detektion der freien Wasseroberfläche oder zeitliche Vermessung von Kolken. Durch die hohen räumlichen und zeitlichen Auflösungen, welche neueste Kamerasensoren liefern, können neue Erkenntnisse in turbulenten, komplexen Strömungen gewonnen werden. Auch in der Praxis können diese Verfahren mit geringem Aufwand wichtige Daten liefern. KW - Wasserbau KW - Architektur KW - Wasserwirtschaft KW - Deutschland Y1 - 2024 SN - 0043-0978 VL - 114 IS - 4 SP - 47 EP - 53 PB - Springer Vieweg CY - Wiesbaden ER - TY - CHAP A1 - Schult, Prince Garcia A1 - Losse, Ann-Kathrin A1 - Czarnecki, Christian A1 - Sultanow, Eldar T1 - Proposing a Framework to address the Sustainable Development Goals T2 - EnviroInfo 2023 N2 - Reducing poverty, protecting the planet, and improving life on earth for everyone are the essential goals of the "2030 Agenda for Sustainable Development"committed by the United Nations (UN). Achieving those goals will require technological innovation as well as their implementation in almost all areas of our business and day-to-day life. This paper proposes a high-level framework that collects and structures different uses cases addressing the goals defined by the UN. Hence, it contributes to the discussion by proposing technical innovations that can be used to achieve those goals. As an example, the goal "Climate Actionïs discussed in detail by describing use cases related to tackling biodiversity loss in order to conservate ecosystems. Y1 - 2023 SN - 978-3-88579-736-4 U6 - https://doi.org/10.18420/env2023-022 SN - 1617-5468 N1 - EnviroInfo 2023, 11. - 23. October 2023, Garching, Germany SP - 243 EP - 249 PB - GI - Gesellschaft für Informatik CY - Bonn ER - TY - JOUR A1 - Oertel, Mario A1 - Bung, Daniel Bernhard T1 - Hochwasserschutz - eine Aufgabe für eine nachhaltige Wasserwirtschaft JF - Wasserwirtschaft KW - Wasserbau KW - Architektur KW - Wasserwirtschaft KW - Deutschland Y1 - 2021 SN - 0043-0978 VL - 111 IS - 9-10 SP - 3 EP - 19 PB - Springer Vieweg CY - Wiesbaden ER - TY - CHAP A1 - Vladova, Gergana A1 - Ullrich, André A1 - Sultanow, Eldar A1 - Tobolla, Marinho A1 - Sebrak, Sebastian A1 - Czarnecki, Christian A1 - Brockmann, Carsten T1 - Visual analytics for knowledge management T2 - INFORMATIK 2023 - Designing Futures: Zukünfte gestalten N2 - The management of knowledge in organizations considers both established long-term processes and cooperation in agile project teams. Since knowledge can be both tacit and explicit, its transfer from the individual to the organizational knowledge base poses a challenge in organizations. This challenge increases when the fluctuation of knowledge carriers is exceptionally high. Especially in large projects in which external consultants are involved, there is a risk that critical, company-relevant knowledge generated in the project will leave the company with the external knowledge carrier and thus be lost. In this paper, we show the advantages of an early warning system for knowledge management to avoid this loss. In particular, the potential of visual analytics in the context of knowledge management systems is presented and discussed. We present a project for the development of a business-critical software system and discuss the first implementations and results. Y1 - 2023 SN - 978-3-88579-731-9 U6 - https://doi.org/10.18420/inf2023_187 SN - 1617-5468 N1 - INFORMATIK 2023, 26. - 29. September 2023, Berlin SP - 1851 EP - 1870 PB - GI - Gesellschaft für Informatik CY - Bonn ER - TY - CHAP A1 - Losse, Ann-Kathrin A1 - Gehrke, Melanie A1 - Ullrich, André A1 - Czarnecki, Christian A1 - Sultanow, Eldar A1 - Breithaupt, Carsten A1 - Koch, Christian T1 - Entwicklung einer Open-Data-Referenzarchitektur für die Luftfahrtindustrie T2 - INFORMATIK 2022 - Informatik in den Naturwissenschaften, Proceedings N2 - Open Data impliziert die freie Zugänglichkeit, Verfügbarkeit und Wiederverwendbarkeit von Datensätzen. Obwohl hochwertige Datensätze öffentlich verfügbar sind, ist der Zugang zu diesen und die Transparenz über die Formate nicht immer gegeben. Dies mindert die optimale Nutzung des Potenzials zur Wertschöpfung, trotz der vorherrschenden Einigkeit über ihre Chancen. Denn Open Data ermöglicht das Vorantreiben von Compliance-Themen wie Transparenz und Rechenschaftspflicht bis hin zur Förderung von Innovationen. Die Nutzung von Open Data erfordert Mut und eine gemeinsame Anstrengung verschiedener Akteure und Branchen. Im Rahmen des vorliegenden Beitrags werden auf Grundlage des Design Science-Ansatzes eine Open Data Capability Map sowie darauf aufbauend eine Datenarchitektur für Open Data in der Luftfahrtindustrie an einem Beispiel entwickelt. Y1 - 2022 SN - 978-3-88579-720-3 U6 - https://doi.org/10.18420/inf2022_103 SN - 1617-5468 N1 - INFORMATIK 2022, 26. - 30. September 2022, Hamburg SP - 1203 EP - 1209 PB - GI - Gesellschaft für Informatik CY - Bonn ER - TY - JOUR A1 - Bung, Daniel Bernhard T1 - Extreme flooding in Western Germany: some thoughts on hazards, return periods and risk JF - Hydrolink N2 - The low-pressure system Bernd involved extreme rainfalls in the Western part of Germany in July 2021, resulting in major floods, severe damages and a tremendous number of casualties. Such extreme events are rare and full flood protection can never be ensured with reasonable financial means. But still, this event must be starting point to reconsider current design concepts. This article aims at sharing some thoughts on potential hazards, the selection of return periods and remaining risk with the focus on Germany. Y1 - 2021 IS - 4 SP - 108 EP - 113 PB - International Association for Hydro-Environment Engineering and Research (IAHR) CY - Madrid ER - TY - CHAP A1 - Abele, Daniel A1 - Kleefeld, Andreas ED - Constanda, Christian T1 - New Numerical Results for the Optimization of Neumann Eigenvalues T2 - Computational and Analytic Methods in Science and Engineering N2 - We present new numerical results for shape optimization problems of interior Neumann eigenvalues. This field is not well understood from a theoretical standpoint. The existence of shape maximizers is not proven beyond the first two eigenvalues, so we study the problem numerically. We describe a method to compute the eigenvalues for a given shape that combines the boundary element method with an algorithm for nonlinear eigenvalues. As numerical optimization requires many such evaluations, we put a focus on the efficiency of the method and the implemented routine. The method is well suited for parallelization. Using the resulting fast routines and a specialized parametrization of the shapes, we found improved maxima for several eigenvalues. Y1 - 2020 SN - 978-3-030-48185-8 (Print) SN - 978-3-030-48186-5 (Online) U6 - https://doi.org/10.1007/978-3-030-48186-5_1 SP - 1 EP - 20 PB - Birkhäuser CY - Cham ER - TY - CHAP A1 - Pieronek, Lukas A1 - Kleefeld, Andreas ED - Constanda, Christian ED - Harris, Paul T1 - The Method of Fundamental Solutions for Computing Interior Transmission Eigenvalues of Inhomogeneous Media T2 - Integral Methods in Science and Engineering: Analytic Treatment and Numerical Approximations N2 - The method of fundamental solutions is applied to the approximate computation of interior transmission eigenvalues for a special class of inhomogeneous media in two dimensions. We give a short approximation analysis accompanied with numerical results that clearly prove practical convenience of our alternative approach. Y1 - 2019 SN - 978-3-030-16077-7 U6 - https://doi.org/10.1007/978-3-030-16077-7_28 SP - 353 EP - 365 PB - Birkhäuser CY - Cham ER - TY - CHAP A1 - Kahra, Marvin A1 - Breuß, Michael A1 - Kleefeld, Andreas A1 - Welk, Martin ED - Brunetti, Sara ED - Frosini, Andrea ED - Rinaldi, Simone T1 - An Approach to Colour Morphological Supremum Formation Using the LogSumExp Approximation T2 - Discrete Geometry and Mathematical Morphology N2 - Mathematical morphology is a part of image processing that has proven to be fruitful for numerous applications. Two main operations in mathematical morphology are dilation and erosion. These are based on the construction of a supremum or infimum with respect to an order over the tonal range in a certain section of the image. The tonal ordering can easily be realised in grey-scale morphology, and some morphological methods have been proposed for colour morphology. However, all of these have certain limitations. In this paper we present a novel approach to colour morphology extending upon previous work in the field based on the Loewner order. We propose to consider an approximation of the supremum by means of a log-sum exponentiation introduced by Maslov. We apply this to the embedding of an RGB image in a field of symmetric 2x2 matrices. In this way we obtain nearly isotropic matrices representing colours and the structural advantage of transitivity. In numerical experiments we highlight some remarkable properties of the proposed approach. Y1 - 2024 SN - 978-3-031-57793-2 U6 - https://doi.org/10.1007/978-3-031-57793-2_25 N1 - Third International Joint Conference, DGMM 2024, Florence, Italy, April 15–18, 2024 SP - 325 EP - 337 PB - Springer CY - Cham ER - TY - JOUR A1 - Ayala, Rafael Ceja A1 - Harris, Isaac A1 - Kleefeld, Andreas T1 - Direct sampling method via Landweber iteration for an absorbing scatterer with a conductive boundary JF - Inverse Problems and Imaging N2 - In this paper, we consider the inverse shape problem of recovering isotropic scatterers with a conductive boundary condition. Here, we assume that the measured far-field data is known at a fixed wave number. Motivated by recent work, we study a new direct sampling indicator based on the Landweber iteration and the factorization method. Therefore, we prove the connection between these reconstruction methods. The method studied here falls under the category of qualitative reconstruction methods where an imaging function is used to recover the absorbing scatterer. We prove stability of our new imaging function as well as derive a discrepancy principle for recovering the regularization parameter. The theoretical results are verified with numerical examples to show how the reconstruction performs by the new Landweber direct sampling method. Y1 - 2024 U6 - https://doi.org/10.3934/ipi.2023051 SN - 1930-8337 SN - 1930-8345 (eISSN) VL - 18 IS - 3 SP - 708 EP - 729 PB - AIMS CY - Springfield ER - TY - JOUR A1 - Clausnitzer, Julian A1 - Kleefeld, Andreas T1 - A spectral Galerkin exponential Euler time-stepping scheme for parabolic SPDEs on two-dimensional domains with a C² boundary JF - Discrete and Continuous Dynamical Systems - Series B N2 - We consider the numerical approximation of second-order semi-linear parabolic stochastic partial differential equations interpreted in the mild sense which we solve on general two-dimensional domains with a C² boundary with homogeneous Dirichlet boundary conditions. The equations are driven by Gaussian additive noise, and several Lipschitz-like conditions are imposed on the nonlinear function. We discretize in space with a spectral Galerkin method and in time using an explicit Euler-like scheme. For irregular shapes, the necessary Dirichlet eigenvalues and eigenfunctions are obtained from a boundary integral equation method. This yields a nonlinear eigenvalue problem, which is discretized using a boundary element collocation method and is solved with the Beyn contour integral algorithm. We present an error analysis as well as numerical results on an exemplary asymmetric shape, and point out limitations of the approach. KW - Nonlinear eigenvalue problems KW - Boundary integral equations, KW - Exponential Euler scheme, KW - Parabolic SPDEs Y1 - 2024 U6 - https://doi.org/10.3934/dcdsb.2023148 SN - 1531-3492 SN - 1553-524X (eISSN) VL - 29 IS - 4 SP - 1624 EP - 1651 PB - AIMS CY - Springfield ER - TY - JOUR A1 - Harris, Isaac A1 - Kleefeld, Andreas T1 - Analysis and computation of the transmission eigenvalues with a conductive boundary condition JF - Applicable Analysis N2 - We provide a new analytical and computational study of the transmission eigenvalues with a conductive boundary condition. These eigenvalues are derived from the scalar inverse scattering problem for an inhomogeneous material with a conductive boundary condition. The goal is to study how these eigenvalues depend on the material parameters in order to estimate the refractive index. The analytical questions we study are: deriving Faber–Krahn type lower bounds, the discreteness and limiting behavior of the transmission eigenvalues as the conductivity tends to infinity for a sign changing contrast. We also provide a numerical study of a new boundary integral equation for computing the eigenvalues. Lastly, using the limiting behavior we will numerically estimate the refractive index from the eigenvalues provided the conductivity is sufficiently large but unknown. KW - Boundary integral equations KW - Inverse spectral problem KW - Conductive boundary condition KW - Transmission eigenvalues Y1 - 2020 U6 - https://doi.org/10.1080/00036811.2020.1789598 SN - 1563-504X VL - 101 IS - 6 SP - 1880 EP - 1895 PB - Taylor & Francis CY - London ER - TY - JOUR A1 - Chwallek, Constanze A1 - Nawrath, Lara A1 - Krastina, Anzelika A1 - Bruksle, Ieva T1 - Supportive research on sustainable entrepreneurship and business practices JF - SECA Sustainable Entrepreneurship for Climate Action Y1 - 2024 SN - 978-952-316-514-4 (pdf) SN - 2954-1654 (on-line publication) IS - 3 PB - Lapland University of Applied Sciences Ltd CY - Rovaniemi ER - TY - CHAP A1 - Burgeth, Bernhard A1 - Kleefeld, Andreas A1 - Zhang, Eugene A1 - Zhang, Yue ED - Baudrier, Étienne ED - Naegel, Benoît ED - Krähenbühl, Adrien ED - Tajine, Mohamed T1 - Towards Topological Analysis of Non-symmetric Tensor Fields via Complexification T2 - Discrete Geometry and Mathematical Morphology N2 - Fields of asymmetric tensors play an important role in many applications such as medical imaging (diffusion tensor magnetic resonance imaging), physics, and civil engineering (for example Cauchy-Green-deformation tensor, strain tensor with local rotations, etc.). However, such asymmetric tensors are usually symmetrized and then further processed. Using this procedure results in a loss of information. A new method for the processing of asymmetric tensor fields is proposed restricting our attention to tensors of second-order given by a 2x2 array or matrix with real entries. This is achieved by a transformation resulting in Hermitian matrices that have an eigendecomposition similar to symmetric matrices. With this new idea numerical results for real-world data arising from a deformation of an object by external forces are given. It is shown that the asymmetric part indeed contains valuable information. Y1 - 2022 SN - 978-3-031-19897-7 U6 - https://doi.org/10.1007/978-3-031-19897-7_5 N1 - Second International Joint Conference, DGMM 2022, Strasbourg, France, October 24–27, 2022 N1 - Corresponding author: Andreas Kleefeld SP - 48 EP - 59 PB - Springer CY - Cham ER - TY - JOUR A1 - Kleefeld, Andreas A1 - Zimmermann, M. ED - Constanda, Christian ED - Bodmann, Bardo E.J. ED - Harris, Paul J. T1 - Computing Elastic Interior Transmission Eigenvalues JF - Integral Methods in Science and Engineering N2 - An alternative method is presented to numerically compute interior elastic transmission eigenvalues for various domains in two dimensions. This is achieved by discretizing the resulting system of boundary integral equations in combination with a nonlinear eigenvalue solver. Numerical results are given to show that this new approach can provide better results than the finite element method when dealing with general domains. Y1 - 2022 SN - 978-3-031-07171-3 U6 - https://doi.org/10.1007/978-3-031-07171-3_10 N1 - Corresponding author: Andreas Kleefeld SP - 139 EP - 155 PB - Birkhäuser CY - Cham ER - TY - GEN A1 - Burgeth, Bernhard A1 - Kleefeld, Andreas A1 - Naegel, Benoît A1 - Perret, Benjamin T1 - Editorial — Special Issue: ISMM 2019 T2 - Mathematical Morphology - Theory and Applications N2 - This editorial presents the Special Issue dedicated to the conference ISMM 2019 and summarizes the articles published in this Special Issue. Y1 - 2020 U6 - https://doi.org/10.1515/mathm-2020-0200 SN - 2353-3390 VL - 4 IS - 1 SP - 159 EP - 161 PB - De Gruyter CY - Warschau ER - TY - JOUR A1 - Kleefeld, Andreas T1 - The hot spots conjecture can be false: some numerical examples JF - Advances in Computational Mathematics N2 - The hot spots conjecture is only known to be true for special geometries. This paper shows numerically that the hot spots conjecture can fail to be true for easy to construct bounded domains with one hole. The underlying eigenvalue problem for the Laplace equation with Neumann boundary condition is solved with boundary integral equations yielding a non-linear eigenvalue problem. Its discretization via the boundary element collocation method in combination with the algorithm by Beyn yields highly accurate results both for the first non-zero eigenvalue and its corresponding eigenfunction which is due to superconvergence. Additionally, it can be shown numerically that the ratio between the maximal/minimal value inside the domain and its maximal/minimal value on the boundary can be larger than 1 + 10− 3. Finally, numerical examples for easy to construct domains with up to five holes are provided which fail the hot spots conjecture as well. KW - Numerics KW - Boundary integral equations KW - Potential theory KW - Helmholtz equation KW - Interior Neumann eigenvalues Y1 - 2021 U6 - https://doi.org/10.1007/s10444-021-09911-5 SN - 1019-7168 VL - 47 PB - Springer CY - Dordrecht ER - TY - JOUR A1 - Martín-Vaquero, J. A1 - Kleefeld, Andreas T1 - Solving nonlinear parabolic PDEs in several dimensions: Parallelized ESERK codes JF - Journal of Computational Physics N2 - There is a very large number of very important situations which can be modeled with nonlinear parabolic partial differential equations (PDEs) in several dimensions. In general, these PDEs can be solved by discretizing in the spatial variables and transforming them into huge systems of ordinary differential equations (ODEs), which are very stiff. Therefore, standard explicit methods require a large number of iterations to solve stiff problems. But implicit schemes are computationally very expensive when solving huge systems of nonlinear ODEs. Several families of Extrapolated Stabilized Explicit Runge-Kutta schemes (ESERK) with different order of accuracy (3 to 6) are derived and analyzed in this work. They are explicit methods, with stability regions extended, along the negative real semi-axis, quadratically with respect to the number of stages s, hence they can be considered to solve stiff problems much faster than traditional explicit schemes. Additionally, they allow the adaptation of the step length easily with a very small cost. Two new families of ESERK schemes (ESERK3 and ESERK6) are derived, and analyzed, in this work. Each family has more than 50 new schemes, with up to 84.000 stages in the case of ESERK6. For the first time, we also parallelized all these new variable step length and variable number of stages algorithms (ESERK3, ESERK4, ESERK5, and ESERK6). These parallelized strategies allow to decrease times significantly, as it is discussed and also shown numerically in two problems. Thus, the new codes provide very good results compared to other well-known ODE solvers. Finally, a new strategy is proposed to increase the efficiency of these schemes, and it is discussed the idea of combining ESERK families in one code, because typically, stiff problems have different zones and according to them and the requested tolerance the optimum order of convergence is different. KW - Multi-dimensional partial differential equations KW - Higher-order codes KW - Nonlinear PDEs Y1 - 2020 U6 - https://doi.org/10.1016/j.jcp.2020.109771 SN - 0021-9991 IS - 423 PB - Elsevier CY - Amsterdam ER - TY - CHAP A1 - Kleefeld, Andreas ED - Constanda, Christian T1 - Numerical calculation of interior transmission eigenvalues with mixed boundary conditions T2 - Computational and Analytic Methods in Science and Engineering N2 - Interior transmission eigenvalue problems for the Helmholtz equation play an important role in inverse wave scattering. Some distribution properties of those eigenvalues in the complex plane are reviewed. Further, a new scattering model for the interior transmission eigenvalue problem with mixed boundary conditions is described and an efficient algorithm for computing the interior transmission eigenvalues is proposed. Finally, extensive numerical results for a variety of two-dimensional scatterers are presented to show the validity of the proposed scheme. Y1 - 2020 SN - 978-3-030-48185-8 (Hardcover) U6 - https://doi.org/10.1007/978-3-030-48186-5_9 SP - 173 EP - 195 PB - Birkhäuser CY - Cham ER - TY - JOUR A1 - Asante-Asamani, E.O. A1 - Kleefeld, Andreas A1 - Wade, B.A. T1 - A second-order exponential time differencing scheme for non-linear reaction-diffusion systems with dimensional splitting JF - Journal of Computational Physics N2 - A second-order L-stable exponential time-differencing (ETD) method is developed by combining an ETD scheme with approximating the matrix exponentials by rational functions having real distinct poles (RDP), together with a dimensional splitting integrating factor technique. A variety of non-linear reaction-diffusion equations in two and three dimensions with either Dirichlet, Neumann, or periodic boundary conditions are solved with this scheme and shown to outperform a variety of other second-order implicit-explicit schemes. An additional performance boost is gained through further use of basic parallelization techniques. KW - Exponential time differencing KW - Real distinct pole KW - Dimensional splitting KW - Reaction-diffusion systems KW - Matrix exponential Y1 - 2020 U6 - https://doi.org/10.1016/j.jcp.2020.109490 SN - 0021-9991 N1 - Corresponding author: Andreas Kleefeld VL - 415 PB - Elsevier CY - Amsterdam ER - TY - JOUR A1 - Breuß, Michael A1 - Kleefeld, Andreas T1 - Implicit monotone difference methods for scalar conservation laws with source terms JF - Acta Mathematica Vietnamica N2 - In this article, a concept of implicit methods for scalar conservation laws in one or more spatial dimensions allowing also for source terms of various types is presented. This material is a significant extension of previous work of the first author (Breuß SIAM J. Numer. Anal. 43(3), 970–986 2005). Implicit notions are developed that are centered around a monotonicity criterion. We demonstrate a connection between a numerical scheme and a discrete entropy inequality, which is based on a classical approach by Crandall and Majda. Additionally, three implicit methods are investigated using the developed notions. Next, we conduct a convergence proof which is not based on a classical compactness argument. Finally, the theoretical results are confirmed by various numerical tests. KW - Entropy solution KW - Source term KW - Monotone methods KW - Implicit methods KW - Finite difference methods KW - Conservation laws Y1 - 2020 U6 - https://doi.org/10.1007/s40306-019-00354-1 SN - 2315-4144 N1 - Corresponding author: Andreas Kleefeld VL - 45 SP - 709 EP - 738 PB - Springer Singapore CY - Singapore ER - TY - JOUR A1 - Harris, Isaac A1 - Kleefeld, Andreas T1 - The inverse scattering problem for a conductive boundary condition and transmission eigenvalues JF - Applicable Analysis N2 - In this paper, we consider the inverse scattering problem associated with an inhomogeneous media with a conductive boundary. In particular, we are interested in two problems that arise from this inverse problem: the inverse conductivity problem and the corresponding interior transmission eigenvalue problem. The inverse conductivity problem is to recover the conductive boundary parameter from the measured scattering data. We prove that the measured scatted data uniquely determine the conductivity parameter as well as describe a direct algorithm to recover the conductivity. The interior transmission eigenvalue problem is an eigenvalue problem associated with the inverse scattering of such materials. We investigate the convergence of the eigenvalues as the conductivity parameter tends to zero as well as prove existence and discreteness for the case of an absorbing media. Lastly, several numerical and analytical results support the theory and we show that the inside–outside duality method can be used to reconstruct the interior conductive eigenvalues. KW - Transmission eigenvalues KW - Conductive boundary condition KW - Inverse scattering Y1 - 2018 U6 - https://doi.org/10.1080/00036811.2018.1504028 SN - 1563-504X VL - 99 IS - 3 SP - 508 EP - 529 PB - Taylor & Francis CY - London ER - TY - JOUR A1 - Fiedler, Thomas M. A1 - Orzada, Stephan A1 - Flöser, Martina A1 - Rietsch, Stefan H. G. A1 - Quick, Harald H. A1 - Ladd, Mark E. A1 - Bitz, Andreas T1 - Performance analysis of integrated RF microstrip transmit antenna arrays with high channel count for body imaging at 7 T JF - NMR in Biomedicine N2 - The aim of the current study was to investigate the performance of integrated RF transmit arrays with high channel count consisting of meander microstrip antennas for body imaging at 7 T and to optimize the position and number of transmit ele- ments. RF simulations using multiring antenna arrays placed behind the bore liner were performed for realistic exposure conditions for body imaging. Simulations were performed for arrays with as few as eight elements and for arrays with high channel counts of up to 48 elements. The B1+ field was evaluated regarding the degrees of freedom for RF shimming in the abdomen. Worst-case specific absorption rate (SARwc ), SAR overestimation in the matrix compression, the number of virtual obser- vation points (VOPs) and SAR efficiency were evaluated. Constrained RF shimming was performed in differently oriented regions of interest in the body, and the devia- tion from a target B1+ field was evaluated. Results show that integrated multiring arrays are able to generate homogeneous B1+ field distributions for large FOVs, espe- cially for coronal/sagittal slices, and thus enable body imaging at 7 T with a clinical workflow; however, a low duty cycle or a high SAR is required to achieve homoge- neous B1+ distributions and to exploit the full potential. In conclusion, integrated arrays allow for high element counts that have high degrees of freedom for the pulse optimization but also produce high SARwc , which reduces the SAR accuracy in the VOP compression for low-SAR protocols, leading to a potential reduction in array performance. Smaller SAR overestimations can increase SAR accuracy, but lead to a high number of VOPs, which increases the computational cost for VOP evaluation and makes online SAR monitoring or pulse optimization challenging. Arrays with interleaved rings showed the best results in the study. KW - body imaging at UHF MRI KW - integrated transmit coil arrays KW - VOP compression Y1 - 2021 U6 - https://doi.org/10.1002/nbm.4515 SN - 0952-3480 (ISSN) SN - 1099-1492 (eISSN) VL - 34 IS - 7 PB - Wiley CY - Weinheim ER - TY - RPRT A1 - Hoffmann, Sarah A1 - Ullrich, Anna Valentine T1 - 30 Minuten FDM für HAW. Ein Informationsformat für Forschende an HAW in NRW N2 - Wie kann man das Thema Forschungsdatenmanagement (FDM) konkret und anwendbar für Forschende gestalten, die bisher noch wenig Kontakt damit hatten? Auf diese Frage gibt das Konzept „30 Minuten FDM für HAW. Ein Informationsformat für Forschende an HAW in NRW“ eine Antwort. Es entstand als Projektarbeit im Zertifikatskurs Forschungsdatenmanagement 2023/24 Y1 - 2024 U6 - https://doi.org/10.5281/zenodo.12569282 ER - TY - RPRT A1 - Birmans, Katrin A1 - Schick, Elena A1 - Tambornino, Philipp A1 - Ullrich, Anna Valentine T1 - Ingenieurwissenschaften im Fokus: Zugänge zu einem effektiven Forschungsdatenmanagement an HAW N2 - Im Rahmen der Love Data Week vom 12. bis 16.02.2024 haben die BMBF-Projekte FDM2_TH_Koeln der TH Köln (FK 16FDFH105) und Persist@HAW der FH Aachen (FK 16FDFH129) am 15.02.2024 gemeinsam eine Online-Veranstaltung mit dem Titel „Ingenieurwissenschaften im Fokus: Zugänge zu einem effektiven Forschungsdatenmanagement an HAW“ angeboten. Diese richtete sich an Forschende aus den Ingenieurwissenschaften, die einen ersten Zugang zum Thema Forschungsdatenmanagement (FDM) suchen und erfahren möchten, welche speziellen Angebote für die Daten aus den Ingenieurwissenschaften existieren. In der Veranstaltung wurden wesentliche Aspekte des Forschungsdatenmanagements entlang des Datenlebenszyklus beleuchtet. Ziel war es, den Teilnehmenden praxisnahe Einblicke und Hilfestellungen zu einem effektiven Umgang mit Forschungsdaten an Hochschulen für Angewandte Wissenschaften (HAW) zu bieten. Durch Beispiele und konkrete Empfehlungen wurde das Thema zugänglich gemacht. Y1 - 2024 U6 - https://doi.org/10.5281/zenodo.12545429 N1 - Die Originalpräsentation ist über Conceptboard einsehbar: https://app.conceptboard.com/board/c651-e781-dr9h-zfyu-gkq9 ER - TY - RPRT A1 - Birmans, Katrin A1 - Tambornino, Philipp A1 - Ullrich, Anna Valentine T1 - Bevor Sie Coscine nutzen - Handreichung für Forschende an HAW N2 - Um die Forschungsdatenmanagement-Plattform Coscine optimal für Forschungsprojekte nutzen zu können, ist es sinnvoll, einige Fragen im Vorhinein zu klären. So können aufwendige Änderungen der Datenverwaltung im Nachhinein vermieden werden. Hierzu bietet die Handreichung hilfreiche Leitfragen und Erläuterungen für Forschende und FDM-Service-Personal an HAW in NRW (DH.NRW-Hochschulen). FDM-Service-Mitarbeitende können die Handreichung in ihrer Beratung zu Coscine einsetzen und mit der Eingabemaske in der Kopfzeile des Dokuments auf ihre Hochschule anpassen. Y1 - 2024 U6 - https://doi.org/10.5281/zenodo.12158546 N1 - Die Handreichung ist im Projekt Persist@HAW (FK: 16FDFH129), gefördert vom BMBF, entstanden. ER - TY - RPRT A1 - Birmans, Katrin A1 - Tambornino, Philipp A1 - Ullrich, Anna Valentine T1 - 5 Gründe für Coscine - Handreichung für Forschende an HAW N2 - Welche Vorteile bietet die Forschungsdatenmanagement-Plattform Coscine für die Verwaltung von Daten in Forschungsprojekten? Hierzu gibt die Handreichung einen schnellen Überblick über den landesgeförderten Dienst Coscine für Forschende und FDM-Service-Personal an HAW in NRW (DH.NRW-Hochschulen). FDM-Service-Mitarbeitende können die Handreichung in ihrer Beratung zu Coscine einsetzen und mit der Eingabemaske in der Kopfzeile des Dokuments auf ihre Hochschule anpassen. Y1 - 2024 U6 - https://doi.org/10.5281/zenodo.12156734 N1 - Die Handreichung ist im Projekt Persist@HAW (FK: 16FDFH129), gefördert vom BMBF, entstanden. ER - TY - CHAP A1 - Becker, Tim A1 - Bragard, Michael T1 - Low-Voltage DC Training Lab for Electric Drives - Optimizing the Balancing Act Between High Student Throughput and Individual Learning Speed T2 - 2024 IEEE Global Engineering Education Conference (EDUCON) N2 - After a brief introduction of conventional laboratory structures, this work focuses on an innovative and universal approach for a setup of a training laboratory for electric machines and drive systems. The novel approach employs a central 48 V DC bus, which forms the backbone of the structure. Several sets of DC machine, asynchronous machine and synchronous machine are connected to this bus. The advantages of the novel system structure are manifold, both from a didactic and a technical point of view: Student groups can work on their own performance level in a highly parallelized and at the same time individualized way. Additional training setups (similar or different) can easily be added. Only the total power dissipation has to be provided, i.e. the DC bus balances the power flow between the student groups. Comparative results of course evaluations of several cohorts of students are shown. KW - Synchronous machines KW - Power dissipation KW - Throughput KW - Low voltage KW - DC machines KW - Manifolds KW - Training Y1 - 2024 U6 - https://doi.org/10.1109/EDUCON60312.2024.10578902 SN - 2165-9559 SN - 2165-9567 (eISSN) N1 - 2024 IEEE Global Engineering Education Conference (EDUCON), 08-11 May 2024, Kos Island, Greece PB - IEEE CY - New York, NY ER - TY - CHAP A1 - Rütters, René A1 - Bragard, Michael A1 - Dolls, Sarah T1 - The Inverted Rotary Pendulum: Facilitating Practical Teaching in Advanced Control Engineering T2 - 2024 IEEE Global Engineering Education Conference (EDUCON) N2 - This paper outlines a practical approach to teach control engineering principles, with an inverted rotary pendulum, serving as an illustrative example. It shows how the pendulum is embedded in an advanced course of control engineering. This approach is incorporated into a flipped-classroom concept, as well as classical teaching concepts, offering students practical experience in control engineering. In addition, the design of the pendulum is shown, using a Raspberry Pi as the target platform for Matlab Simulink. This pendulum can be used in the classroom to evaluate the controller design mentioned above. It is analysed if the use of the pendulum generates a deeper understanding of the learning contents. KW - Matlab KW - Engineering education KW - Online services KW - Software packages KW - Electronic learning KW - Control engineering Y1 - 2024 U6 - https://doi.org/10.1109/EDUCON60312.2024.10578937 SN - 2165-9559 SN - 2165-9567 (eISSN) N1 - 2024 IEEE Global Engineering Education Conference (EDUCON), 08-11 May 2024, Kos Island, Greece PB - IEEE CY - New York, NY ER - TY - CHAP A1 - Kramer, Pia A1 - Bragard, Michael A1 - Ritz, Thomas A1 - Ferfer, Ute A1 - Schiffers, Tim T1 - Visualizing, Enhancing and Predicting Students’ Success through ECTS Monitoring T2 - 2024 IEEE Global Engineering Education Conference (EDUCON) N2 - This paper serves as an introduction to the ECTS monitoring system and its potential applications in higher education. It also emphasizes the potential for ECTS monitoring to become a proactive system, supporting students by predicting academic success and identifying groups of potential dropouts for tailored support services. The use of the nearest neighbor analysis is suggested for improving data analysis and prediction accuracy. KW - Monitoring KW - Engineering education KW - Data visualization KW - Accuracy KW - Data analysis Y1 - 2024 U6 - https://doi.org/10.1109/EDUCON60312.2024.10578652 SN - 2165-9559 SN - 2165-9567 (eISSN) N1 - 2024 IEEE Global Engineering Education Conference (EDUCON), 08-11 May 2024, Kos Island, Greece PB - IEEE CY - New York, NY ER - TY - RPRT A1 - Barnat, Miriam A1 - Arntz, Kristian A1 - Bernecker, Andreas A1 - Fissabre, Anke A1 - Franken, Norbert A1 - Goldbach, Daniel A1 - Hüning, Felix A1 - Jörissen, Jörg A1 - Kirsch, Ansgar A1 - Pettrak, Jürgen A1 - Rexforth, Matthias A1 - Josef, Rosenkranz A1 - Terstegge, Andreas T1 - Strategische Gestaltung von Studiengängen für die Zukunft: Ein kollaborativ entwickeltes Self-Assessment BT - Diskussionspapier Nr. 33 T2 - Hochschulforum Digitalisierung - Diskussionspapier N2 - Das Diskussionspapier beschreibt einen Prozess an der FH Aachen zur Entwicklung und Implementierung eines Self-Assessment-Tools für Studiengänge. Dieser Prozess zielte darauf ab, die Relevanz der Themen Digitalisierung, Internationalisierung und Nachhaltigkeit in Studiengängen zu stärken. Durch Workshops und kollaborative Entwicklung mit Studiendekan:innen entstand ein Fragebogen, der zur Reflexion und strategischen Weiterentwicklung der Studiengänge dient. Y1 - 2024 SN - 2365-7081 PB - Stifterverband für die Deutsche Wissenschaft CY - Berlin ER - TY - JOUR A1 - Golland, Alexander A1 - Kriegesmann, Torben T1 - Zivilprozessuale Fragen zum datenschutzrechtlichen Schadensersatzanspruch JF - MMR - Zeitschrift für IT-Recht und Recht der Digitalisierung N2 - Im Verfahren gegen die Österreichische Post AG (Rs. C-300/21) befasste sich der EuGH erstmals mit dem in Art. 82 DS-GVO geregelten datenschutzrechtlichen Schadensersatzanspruch. Mit den Klarstellungen des EuGH verschieben sich die Probleme nun stärker zu den „klassischen“ Fragen des Schadensersatzrechts im Zivilprozess. Relevant sind dabei vor allem Aspekte der Darlegungs- und Beweislast und deren Besonderheiten mit Blick auf den Ersatz immaterieller Schäden. Der Beitrag fokussiert sich auf die Voraussetzungen und den dabei zu führenden Tatsachenbeweis bei der Klage des Betroffenen gegen den Verantwortlichen auf Ersatz immaterieller Schäden. Y1 - 2023 SN - 2698-7988 IS - 10 SP - 733 EP - 739 PB - Beck CY - München ER - TY - CHAP A1 - Golland, Alexander ED - Wagner, Ralph T1 - Kommentierung von §§ 6 bis 10 EKD-Datenschutzgesetz T2 - EKD-Datenschutzgesetz. Datenschutzbestimmungen der evangelischen Kirche Y1 - 2024 SN - 978-3-8487-8111-9 SP - 153 EP - 228 PB - Nomos CY - Baden-Baden ER - TY - JOUR A1 - Golland, Alexander A1 - Kelbch, Niklas T1 - Kartellrecht vs. Datenschutzrecht: Rechtsgrundlagen für die Datenverarbeitung in sozialen Netzwerken JF - DSB Datenschutz-Berater Y1 - 2023 SN - 0170-7256 IS - 9 SP - 247 EP - 249 PB - DFV Mediengruppe CY - Frankfurt a.M. ER - TY - JOUR A1 - Golland, Alexander T1 - Kompetenz nationaler Wettbewerbsbehörden zur Feststellung eines Verstoßes gegen die DS-GVO BT - Anmerkung zum EuGH-Urteil vom 4.7.2023 JF - MMR - Zeitschrift für IT-Recht und Recht der Digitalisierung Y1 - 2023 IS - 9 SP - 680 EP - 683 PB - Beck CY - München ER - TY - CHAP A1 - Golland, Alexander ED - Riechert, Anne ED - Wilmer, Thomas T1 - Kommentierung von § 26 Telekommunikation-Telemedien-Datenschutzgesetz T2 - TTDSG Y1 - 2022 SN - 978-3-503-20978-1 N1 - Gedruckte Ausgabe unter 21 QRUG 2 verfügbar. SP - 439 EP - 474 PB - Erich Schmidt CY - Berlin ER - TY - JOUR A1 - Golland, Alexander T1 - Bußgelder bei Datenschutzverstößen durch Unternehmen JF - NJW Neue Juristische Wochenschrift N2 - Bald eine Dekade ist es her, dass diese annähernd mantraartig wiederholte Phrase Unternehmen zur Umsetzung datenschutzrechtlicher Vorgaben incentivierte. Was ist davon geblieben? Nur wenige in Deutschland verhängte Bußgelder erreichten Millionenhöhe. Hintergrund ist (auch) das deutsche Ordnungswidrigkeitenrecht, welches in einem Spannungsverhältnis zu den Vorgaben der DS-GVO steht. Ein Bußgeldbescheid der Berliner Datenschutzaufsicht gegen die Deutsche Wohnen sollte Auslöser eines langen, fortdauernden Rechtsstreits werden. Auf Vorlage des KG hatte der EuGH in der Rechtssache C-807/21 („Deutsche Wohnen“) erstmals Gelegenheit, sich zur Frage der Bußgeldhaftung zu positionieren. Y1 - 2024 SN - 0341-1915 IS - 6 SP - 325 EP - 329 PB - Beck CY - München ER - TY - CHAP A1 - Golland, Alexander ED - Riechert, Anne ED - Wilmer, Thomas T1 - Kommentierung von § 7 Telekommunikation-Telemedien-Datenschutzgesetz T2 - TTDSG Y1 - 2022 SN - 978-3-503-20978-1 N1 - Gedruckte Ausgabe unter 21 QRUG 2 verfügbar. SP - 145 EP - 151 PB - Erich Schmidt CY - Berlin ER - TY - JOUR A1 - Golland, Alexander T1 - Datenschutz beim Einsatz künstlicher Intelligenz im Unternehmen JF - NWB N2 - Seit Ende 2022 prägt das Schlagwort „Künstliche Intelligenz“ (KI) nicht nur den rechtswissenschaftlichen Diskurs. Die allgemeine Verfügbarkeit von generativen KI-Modellen, allen voran die großen Sprachmodelle (Large Language Models, kurz: LLM) wie ChatGPT von OpenAI oder Bing AI von Microsoft, erfreuen sich größter Beliebtheit: LLM sind in der Lage, auf Grundlage statistischer Methoden – eine entsprechende Schnittstelle (Interface) vorausgesetzt – auch technisch wenig versierten Nutzern verständliche Antworten auf ihre Fragen zu liefern. Dabei werden nicht nur umfassend Nutzerdaten verarbeitet, sondern auch auf weitere personenbezogene Daten zugegriffen sowie neue Daten erzeugt. Der Beitrag geht der Frage nach, welche spezifischen datenschutzrechtlichen Herausforderungen sich für Unternehmen beim Einsatz solcher LLM stellen. Y1 - 2024 SN - 0028-3460 IS - 6 SP - 425 EP - 432 PB - NWB CY - Herne ER - TY - JOUR A1 - Golland, Alexander A1 - Schröer, Jan-Erik T1 - No risk, no fun? Berücksichtigung datenschutzrechtlicher Risiken im Vergabeverfahren JF - DSB Datenschutz-Berater Y1 - 2024 SN - 0170-7256 SN - No risk, no fun? Berücksichtigung datenschutzrechtlicher Risiken im Vergabeverfahren IS - 5 SP - 114 EP - 117 PB - DFV Mediengruppe CY - Frankfurt a.M. ER - TY - JOUR A1 - Golland, Alexander A1 - Schröer, Jan-Erik T1 - Error 404 im Vergabeverfahren: Datenschutz nicht gefunden? JF - VergabeR N2 - Das Thema Datenschutz wurde bei der öffentlichen Auftragsvergabe bislang vor allem in Bezug auf Drittlandtransfers personenbezogener Daten in die USA diskutiert. Jedoch spielt der Datenschutz für das Vergabeverfahren und für die Ausführung datenschutzrelevanter Leistungen generell eine wesentliche Rolle. Gleichwohl herrschen bislang unter öffentlichen Auftraggebern Schwierigkeiten, datenschutzrechtlich relevante Fallkonstellationen zu erkennen, die möglichen Risiken daraus abzuleiten und, sofern dies gelingt, diesen Risiken angemessen zu begegnen. Der vorliegende Beitrag befasst sich mit der datenschutzrechtlichen Verantwortlichkeit, ihren Folgen und den daraus resultierenden Konsequenzen für die Gestaltung von Vergabeverfahren und Vergabeunterlagen. Y1 - 2024 SN - 2366-2247 IS - 2 SP - 75 EP - 92 PB - Wolters Kluwer CY - Köln ER - TY - THES A1 - Gros, Isabella T1 - Depressed Furniture : eine abstrakte Übersetzung von Depressionen in Möblierung N2 - Depressed Furniture ist eine abstrakte Übersetzung von Depressionen in Möblierung. Es handelt sich um eine Rauminstallation von fünf Leuchten, die der Erkrankung in einem unüblichen Kontext eine Plattform gibt. Dadurch stellt das Projekt eine Schnittstelle zwischen Kunst, Design und Gesellschaft dar. Jede Leuchte verkörpert eine Empfindung, mit der sich ein Großteil der Betroffenen identifizieren kann. Es wird Bewusstsein für die Komplexität der Krankheit geschaffen und das Tabu um mentale Krankheiten gebrochen. Neben der Regular Collection können auch Tischvarianten (Compact Collection) erworben werden. Depressed Furniture zeigt, dass es durchaus möglich ist, eine unschöne Thematik zu abstrahieren und ihr neutral zu begegnen. Es verdeutlicht, wie Design dazu beitragen kann, sensible Themen auf kreative Weise zu kommunizieren. KW - Depressed Furniture KW - Rauminstallation KW - Depressionen KW - Mentale Gesundheit KW - Leuchtenkollektion Y1 - 2024 PB - FH Aachen CY - Aachen ER - TY - THES A1 - Giernich, Marie T1 - Zookunft: Zoo der Zukunft N2 - Inmitten globaler Natur- und Artenschutzherausforderungen ist die Transformation zoologischer Einrichtungen entscheidend. "Zookunft" präsentiert ein innovatives Konzept für ein Tropenhaus im Kölner Zoo, das Natur und Augmented Reality einzigartig verknüpft. Ziel ist ein Raumkonzept, welches den Besucher:innen ein tiefes Verständnis für die Fauna und Flora des südostasiatischen Regenwaldes vermitteln soll. Durch die geschickte Integration von Augmented Reality entsteht eine innovative Lern- und Erlebniswelt, die Umweltschutz- und Artenschutzbemühungen unterstützt und nachhaltige Bildung fördert. Besuchende tauchen aktiv in die faszinierende Welt des Regenwaldes ein, wenn Natur und Augmented Reality eine immersive Umgebung schaffen. "Zookunft" soll als Vorreiter für Zooumgestaltungen dienen, Mensch und Natur verbinden und nachhaltige Bildung fördern. Ein Raum, der Naturerlebnisse und Technologie beeindruckend kombiniert. KW - Zoo KW - Tropenhaus KW - Südostasien KW - Nachhaltigkeit KW - Bildung Y1 - 2024 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER - TY - THES A1 - Fohrer, Emil T1 - ARCHER : become the Arrow BT - Ein Redesign des Freischwingers N2 - „Archer“ ist ein Redesign des Freischwingers. Ein klassischer Freischwinger ist ein aus Rohr gebogener Stuhl ohne Hinterbeine. Das Konzept des Freischwingers macht sich die Elastizität des Stahlrohrs zunutze, um einen schwingenden Sitz zu produzieren. An dieses Konzept knüpft „Archer“ herstellungstechnisch an, ergänzt jedoch ein paar Features. Der erste „USP“ ist die Rückenlehne, welche aus Nylonschnur gewoben ist. Die Lehne rahmt mehrdimensional eine Sattelfläche ein, die sich überraschend ergonomisch dem Rücken anpasst. Sie wächst aus den Armlehnen von vorne hinter dem Rücken zusammen. Eine weitere Neuheit sind die Hinterbeine des Stuhls. Der Schwung soll nicht weg, sondern hin zu dem, was was vor den Nutzenden liegt. In Kombination mit der Lehne, die aus den Armlehnen wächst und hinter dem Rücken schließt, ist das Gewicht über den Beinen gut ausbalanciert. In seinem Aufbau vereint Er ein reduziertes klares Stahlgestell mit dramatisch gewobener Schnur. Die zwei sichtbaren Materialien im Spiel miteinander werden optisch nur noch ergänzt von einem aus Kupfer, Messing oder Edelstahl gedrehten Stopfen mit konischem InLay. Der völlig eigene Aufbau mit Hinterbeinen und Armlehnen erlaubt federleichtes Schwingen, einfaches Aufstehen, neutralisiert Nervosität und fängt den Nutzer / die Nutzerin sanft auf. Die ineinander verwobenen Schnüre teilen das Gewicht gleichmäßig unter sich auf. Industrielle Herstellungsmethoden in Kombination mit Handarbeit machen diesen Stuhl zu etwas besonderem und da dem Konzept farblich kein Ende gesetzt ist, hat jeder Stuhl das Potenzial, zu einem unverkennbaren Einzelstück zu werden. KW - Freischwinger KW - Nylon KW - Stahlgestell KW - Schwung KW - Handarbeit Y1 - 2024 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER - TY - THES A1 - Ernsing, Johanna T1 - Kalle : der mitwachsende Kindertisch N2 - KALLE ist ein mitwachsender Kindertisch, dessen Besonderheit, neben der Höhenverstellung, in der Vergrößerung der Tischplatte liegt. Hierdurch kann KALLE optimal an das Wachstum der Kinder und die sich ändernden Anforderungen angepasst werden. Es ist ein Möbelstück, das die Entwicklung der Kinder begleitet und fördert. Im Gebrauch bezieht sich die Förderung besonders auf die kognitive Entwicklung, die Kreativität und das Sozialverhalten. Darüber hinaus sollen die Kinder mit KALLE aber auch den Umgang mit langlebigen Produkten erlernen, damit sie ein Verständnis für Nachhaltigkeit und ein umweltbewusstes Konsumverhalten entwickeln. KW - Mitwachsender Kindertisch KW - Kindertisch KW - Jugendtisch KW - Kreativitätsförderung KW - Konsumreduzierung Y1 - 2024 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER - TY - THES A1 - Bunar, Moritz T1 - Land Rover Symbiosis : Seegras erforschen und erleben N2 - Seegras wird als „Rohstoff der Zukunft“ betitelt, da es helfen könnte, eine Reihe von globalen Problemen zu bekämpfen. Viele der erhofften Innovationen sind heute aber noch hypothetisch. Außerdem ist das Thema in der westlichen Welt trotz der Neigung zum Klimaschutz kaum bekannt. Die Idee von „Land Rover Symbiosis“ ist ein nachhaltiges Tourismuskonzept, das Forschung und Erlebnisreisen miteinander verknüpft. Auf einer 70m Katamaran Superyacht ist Platz für Forschungszwecke auf der einen und Raum für Expeditionsurlaub auf der anderen Seite. So entsteht ein Verhältnis an Bord, bei dem beide Parteien voneinander profitieren: Wissenschaftler:innen erhalten finanzielle Unterstützung und Kund:innen haben ein klimaneutrales Urlaubserlebnis, bei dem sie hautnah die Vorzüge und Potenziale von Seegras kennenlernen. KW - Seegras KW - Sanfter Tourismus KW - Nachhaltigkeit KW - Superyacht KW - Katamaran Y1 - 2024 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER - TY - THES A1 - Brauweiler, Philipp T1 - incontrare : Gestaltung eines Meeting Raumes durch Konzeptmöbel N2 - Incontrare, was übersetzt Begegnung bedeutet, ist ein Konferenztischkonzept, der durch seinen modularen Aufbau heraus sticht. Dem Kunden ist es möglich das Produkt mit einem einzigen Werkzeug - fünfer Imbusschlüssel - aufzubauen. Der modulare Aufbau bietet die Möglichkeit kundenorientiert ein Produkt zusammensetzen zu können. Incontrare bietet hierdurch eine Vielzahl an Variationen, die nicht nur die gestalterischen Aspekte anspricht, sondern auch verschiedene Preisklassen abdeckt. Incontrare ist ein Tischkonzept, das sowohl im niederpreisigen , sowie auch im HighEnd Bereich funktioniert. KW - Begegnung KW - Verschieben KW - Stimmung KW - Regalkonzept KW - Imbussschlüssel Y1 - 2024 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER - TY - THES A1 - Bartz, Markus T1 - Dupiano : Ein aus einem Bauelement auffaltbarer Keyboradständer mit dem Erscheinungsbild eines akustischen Klavieres. N2 - Klavierspielende Künstlerinnen und Künstler finden sich auf der Bühne meist an einer Kombination aus Keyboard und Keyboardständer wieder. Zwar kann der Klang eines Klaviers technisch brillant simuliert werden, jedoch verliert das Bühnenbild den Mehrwert eines traditionellen Klaviers. Um diesem Verlust von Authentizität und Wohlgefühl auf der Bühne endlich etwas entgegenzusetzen, soll ein "dupiano" gängige Keyboardständer ersetzen und sämtliche Keyboards in das Erscheinungsbild eines akustischen Klaviers hüllen. Dadurch sollen auch die visuellen Eindrücke, verknüpft mit den akustischen, an Authentizität gewinnen und den Klavierauftritt vervollständigen. Es ist leicht, stabil und ohne Werkzeug in unter 10 Sekunden aufbaubar. Auch der Abbau geschieht in unter 10 Sekunden. Verstaut werden kann es von einer Person in jedem Kofferraum. "dupiano" - was nach Klavier klingt, soll auch so aussehen! KW - Keyboard KW - Klavier KW - Keyboardständer KW - Musik KW - Faltbar Y1 - 2024 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER - TY - THES A1 - Ackermann, Vincent T1 - Filos : Design eines Front-Ends für das robotergeführte Laser-Osteotom-System STELLA. N2 - In der Abschlussarbeit „FILOS“ wurde in Zusammenarbeit mit dem Fraunhofer-Institut für Lasertechnik (ILT) ein Front-End für das laserbasierte Osteotom STELLA entwickelt. STELLA soll Kraniotomie (das Eröffnen des Schädels) im wachen Zustand ermöglichen und erfordert eine benutzerfreundliche Bedienungsplattform sowie ein funktionales und ästhetisches Design. Das Ziel von „FILOS“ war es, ein Gehäuse zu entwerfen, das den medizinischen Anforderungen entspricht, und ein Bedienkonzept zu entwickeln, dass die Akzeptanz bei Patient:innen und Anwender:innen fördert. Durch Expert:innen-Interviews mit Neurochirurg:innen und enge Zusammenarbeit mit dem ILT wurde ein durchdachtes Design entwickelt. Dieses soll den Anforderungen der Anwender:innen gerecht werden, das zukünftige Operationssystem repräsentieren und somit einen Mehrwert in der Medizin schaffen. KW - Wachoperation KW - Laserchirurgie KW - Medizintechnik KW - Cobot KW - Industrial Design Y1 - 2024 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER - TY - GEN A1 - Dieringer, Matthias A. A1 - Renz, Wolfgang A1 - Lindel, Tomasz A1 - Seifert, Frank A1 - Frauenrath, Tobias A1 - Waiczies, Helmar A1 - von Knobelsdorff-Brenkhoff, Florian A1 - Santoro, Davide A1 - Hoffmann, Werner A1 - Ittermann, Bernd A1 - Schulz-Menger, Jeanette A1 - Niendorf, Thoralf T1 - 4CH TX/RX Surface Coil for 7T: Design, Optimization and Application for Cardiac Function Imaging T2 - 2010 ISMRM-ESMRMB joint annual meeting N2 - Practical impediments of ultra high field cardiovascular MR (CVMR) can be catalogued in exacerbated magnetic field and radio frequency (RF) inhomogeneities, susceptibility and off-resonance effects, conductive and dielectric effects in tissue, and RF power deposition constraints, which all bear the potential to spoil the benefit of CVMR at 7T. Therefore, a four element cardiac transceive surface coil array was developed. Cardiac imaging provided clinically acceptable signal homogeneity with an excellent blood myocardium contrast. Subtle anatomic structures, such as pericardium, mitral and tricuspid valves and their apparatus, papillary muscles, and trabecles were accurately delineated. Y1 - 2010 SN - 1545-4428 N1 - ISMRM-ESMRMB joint annual meeting, 1 - 7 May 2010, Stockholm, Sweden ER - TY - GEN A1 - Frauenrath, Tobias A1 - Becker, Meike A1 - Hezel, Fabian A1 - Krombach, Gabriele A. A1 - Kremer, Ute A1 - Schulz-Menger, Jeanette A1 - Niendorf, Thoralf T1 - Comparison of Left Function Assessment Using Phonocardiogram and Electrocardiogram Triggered 2D SSFP CINE MR Imaging at 1.5 T and 3.0 T T2 - 2010 ISMRM-ESMRMB joint annual meeting N2 - As high-field cardiac MRI (CMR) becomes more widespread the propensity of ECG to distortions and mistriggering increases and with it the motivation for a cardiac triggering alternative. Hence, this study explores the suitability of acoustic cardiac triggering (ACT) for left ventricular (LV) function assessment in healthy subjects at 1.5T and 3.0T. Y1 - 2010 SN - 1545-4428 N1 - ISMRM-ESMRMB joint annual meeting, 1 - 7 May 2010, Stockholm, Sweden ER - TY - GEN A1 - Hezel, Fabian A1 - Frauenrath, Tobias A1 - Renz, Wolfgang A1 - Schulz-Menger, Jeanette A1 - Niendorf, Thoralf T1 - Feasibility of CINE Myocardial T2* Mapping Using Susceptibility Weighted Gradient-Echo Imaging at 7.0 T T2 - 2010 ISMRM-ESMRMB joint annual meeting N2 - This study is designed to demonstrate the promise of susceptibility weighted 2D CINE FLASH and T2* Mapping of the heart at 7T. Y1 - 2010 SN - 1545-4428 N1 - ISMRM-ESMRMB joint annual meeting, 1 - 7 May 2010, Stockholm, Sweden ER - TY - GEN A1 - Frauenrath, Tobias A1 - Renz, Wolfgang A1 - Rieger, Jan A1 - Gömmel, Andreas A1 - Butenweg, Christoph A1 - Niendorf, Thoralf T1 - High Spatial Resolution 3D MRI of the Larynx Using a Dedicated TX/RX Phased Array Coil at 7.0T T2 - 2010 ISMRM-ESMRMB joint annual meeting N2 - MRI holds great potential for elucidating laryngeal and vocal fold anatomy together with the assessment of physiological processes associated in human phonation. However, MRI of human phonation remains very challenging due to the small size of the targeted structures, interfering signal from fat, air between the vocal folds and surrounding muscles and physiological motion. These anatomical/physiological constraints translate into stringent technical requirements in balancing, scan time, image contrast, immunity to physiological motion, temporal resolution and spatial resolution. Motivated by these challenges and limitations this study is aiming at translating the sensitivity gain at ultra-high magnetic fields for enhanced high spatial resolution 3D imaging of the larynx and vocal tract. To approach this goal a dedicated two channel TX/RX larynx coil is being proposed. Y1 - 2010 SN - 1545-4428 N1 - ISMRM-ESMRMB joint annual meeting, 1 - 7 May 2010, Stockholm, Sweden ER - TY - GEN A1 - Martin, Conrad Steven A1 - Frauenrath, Tobias A1 - Zerdem, Celal A1 - Renz, Wolfgang A1 - Niendorf, Thoralf T1 - Evaluation of Magneto Alert Sensor (MALSE) to Improve MR Safety by Decreasing the Incidence of Ferromagnetic Projectile Accidents T2 - 2011 ISMRM Annual Meeting Proceedings N2 - The magnetic forces of fringe magnetic fields of MR systems on ferromagnetic components can impose a severe patient, occupational health and safety hazard. MRI accidents are listed as number 9 of the top 10 risks in modern medicine. With the advent of ultrahigh field MR systems including passively shielded magnet versions, this risk, commonly known as the missile or projectile effect is even more pronounced. A strategy employing magnetic field sensors which can be attached to ferromagnetic objects that are commonly used in a clinical environment is conceptually appealing for the pursuit of reducing the risk of ferromagnetic projectile accidents. Y1 - 2011 SN - 1545-4428 N1 - ISMRM 19th Annual Meeting & Exhibition, 7-13 May 2011, Montreal, Quebec, Canada ER - TY - GEN A1 - Frauenrath, Tobias A1 - de Geyer d'Orth, Thibaut A1 - Niendorf, Thoralf T1 - Assessment of Accuracy & Reproducibility of ECG, Pulse Oximetry & Phonocardiogram Gating of Cardiac MRI at 7T T2 - 2011 ISMRM Annual Meeting Proceedings N2 - At (ultra)high magnetic fields the artifact sensitivity of ECG recordings increases. This bears the risk of R-wave mis-registration which has been consistently reported for ECG triggered CMR at 7.0T. Realizing the constraints of conventional ECG, acoustic cardiac triggering (ACT) has been proposed. The clinical ACT has not been carefully examined yet. For this reason, this work scrutinizes the suitability, accuracy and reproducibility of ACT for CMR at 7.0T. For this purpose, the trigger reliability and trigger detection variance are examined together with an qualitative and quantitative assessment of image quality of the heart at 7.0T. Y1 - 2011 SN - 1545-4428 N1 - ISMRM 19th Annual Meeting & Exhibition, 7-13 May 2011, Montreal, Quebec, Canada ER - TY - GEN A1 - Frauenrath, Tobias A1 - Dieringer, Matthias A1 - Patel, Nishant A1 - Zerdem, Celal A1 - Hentschel, Jan A1 - Renz, Wolfgang A1 - Niendorf, Thoralf T1 - From Artifact to Merit: Cardiac Gated MRI at 7T & 3T using Magneto-Hydrodynamic Effects for Synchronization T2 - 2011 ISMRM Annual Meeting Proceedings N2 - ECG is corrupted by magneto-hydrodynamic effects at higher magnetic field strength. Artifacts in the ECG trace and severe T-wave elevation might be mis-interpreted as R-waves. MHD being inherently sensitive to blood flow and blood velocity provides an alternative approach for cardiac gating, even in peripheral target areas far away from the commonly used upper torso positions of ECG electrodes. This feature would be very beneficial to address traveling time induced motion artifacts and trigger latency related issues raised by ECG-gated peripheral MR angiography. For all those reasons, this work proposes the use of MHD-trigger for cardiac gated MR. Y1 - 2011 SN - 1545-4428 N1 - ISMRM 19th Annual Meeting & Exhibition, 7-13 May 2011, Montreal, Quebec, Canada ER - TY - GEN A1 - Hering, T. A1 - Ulber, Roland A1 - Tippkötter, Nils T1 - Antimikrobielle Oberflächenmodifikation durch Mikropartikel T2 - Chemie Ingenieur Technik N2 - Die Ausbildung von Biofilmen in technischen Anlagen, wie z. B. Kühlkreisläufen, Wasseraufbereitungssystemen und Bioreaktoren, führen zu Materialschäden (Biofouling) und stark erhöhtem Energieaufwand. Im Rahmen der aktuellen Forschungsarbeiten erfolgen aktive sowie passive Bio-Modifikationen auf funktionalisierten magnetischen Mikropartikelober-flächen. Um die verschiedenen funktionalisierten magnetischen Mikropartikel zu analysieren und ihre antimikrobielle Wirkung zu testen, wird der Einsatz einer 3D-gedruckten, magnetischen Plattform für ein Fluoreszenz-basiertes Screening-System untersucht. Für den Oberflächenschutz wurden verschiedene, antimikrobiell funktionalisierte Partikelkombinationen mit dem Mikroorganismus Escherichia coli GFPmut2 in Bezug auf aktiven Oberflächenschutz verglichen. Um die antimikrobielle Oberflächeneffekte von synergistischen Kombinationen unterschiedlich funktionalisierter Partikel zu bestimmen, werden Oberflächen einem Magnetfeld ausgesetzt, das die Mikropartikel als definierte Schicht auf ihnen zurück hält. Diese modifizierten Oberflächen können sowohl durch Fluoreszenzspektroskopie als auch -mikroskopie analysiert werden. Y1 - 2016 U6 - https://doi.org/10.1002/cite.201650084 N1 - ProcessNet-Jahrestagung 2016 und 32. DECHEMA-Jahrestagung der Biotechnologen 2016, 12. - 15. September 2016, Eurogress Aachen VL - 88 IS - 9 SP - 1302 PB - Wiley-VCH CY - Weinheim ER - TY - GEN A1 - Kuthan, K. A1 - Al-Kaidy, H. A1 - Tippkötter, Nils T1 - Tropfenbasierte Enzymreaktionen auf Glasoberflächen im μL-Maßstab mit ortsaufgelöster pL-Dosierung der Reaktanden T2 - Chemie Ingenieur Technik N2 - Mit der Entwicklung wässriger Tropfen, die mit einer schützenden Hülle magnetisierbarer, hydrophober Partikel umgeben sind, ergeben sich neue Möglichkeiten im Bereich der Mikrofluidik. So können die Tropfen als flüssige Mikroreaktoren eingesetzt werden. Der wässrige Kern dieser Mikroreaktoren besteht aus einer Substratlösung für enzymatische Umsetzungen. Durch Bewegen der Mikroreaktoren können diese über immobilisierten Enzymen positioniert werden, um so einen enzymatischen Umsatz innerhalb der Mikroreaktoren zu realisieren. Hierfür wurde eine neue Mikroreaktorplattform-Technologie etabliert. Die Mikroreaktoren können aufgrund ihrer magnetisierbaren Hüllenpartikel über elektromagnetische Spulen bewegt werden. Die Bewegung erfolgt dabei mit einer automatisierten Aktuatorplattform, bestehend aus einer 3x3 Doppelspulenmatrix mit Magnetkernen. Als modellhaftes Reaktionssystem wird eine Enzymkaskade eingesetzt, die sich aus einer b-Glucosidase, Glucose-Oxidase und Meerrettichperoxidase zusammensetzt. Primär untersuchte Substrate sind Fluorescein-di-b-D-glucopyranoside, und 1-(3,7-Dihydroxy-10H-phenoxazin-10-yl)-ethanon, bei deren Umsatz fluoreszierende Produkte entstehen. Y1 - 2016 U6 - https://doi.org/10.1002/cite.201650117 N1 - ProcessNet-Jahrestagung 2016 und 32. DECHEMA-Jahrestagung der Biotechnologen 2016, 12. - 15. September 2016, Eurogress Aachen VL - 88 IS - 9 SP - 1336 EP - 1337 PB - Wiley-VCH CY - Weinheim ER - TY - JOUR A1 - Aliazizi, Fereshteh A1 - Özsoylu, Dua A1 - Bakhshi Sichani, Soroush A1 - Khorshid, Mehran A1 - Glorieux, Christ A1 - Robbens, Johan A1 - Schöning, Michael J. A1 - Wagner, Patrick T1 - Development and Calibration of a Microfluidic, Chip-Based Sensor System for Monitoring the Physical Properties of Water Samples in Aquacultures JF - Micromachines N2 - In this work, we present a compact, bifunctional chip-based sensor setup that measures the temperature and electrical conductivity of water samples, including specimens from rivers and channels, aquaculture, and the Atlantic Ocean. For conductivity measurements, we utilize the impedance amplitude recorded via interdigitated electrode structures at a single triggering frequency. The results are well in line with data obtained using a calibrated reference instrument. The new setup holds for conductivity values spanning almost two orders of magnitude (river versus ocean water) without the need for equivalent circuit modelling. Temperature measurements were performed in four-point geometry with an on-chip platinum RTD (resistance temperature detector) in the temperature range between 2 °C and 40 °C, showing no hysteresis effects between warming and cooling cycles. Although the meander was not shielded against the liquid, the temperature calibration provided equivalent results to low conductive Milli-Q and highly conductive ocean water. The sensor is therefore suitable for inline and online monitoring purposes in recirculating aquaculture systems. KW - chip-based sensor setup KW - aquaculture KW - microfluidics KW - impedance spectroscopy KW - thermometry KW - electrical conductivity of liquids Y1 - 2024 U6 - https://doi.org/10.3390/mi15060755 SN - 2072-666X N1 - This article belongs to the Special Issue "Multisensor Arrays" N1 - Corresponding author: Michael J. Schöning VL - 15 IS - 6 PB - MDPI CY - Basel ER - TY - CHAP A1 - Fissabre, Anke ED - Naujokat, Anke ED - Hake, Verena ED - Schindler, Bruno ED - Schötten, Björn T1 - Eine moderne Sainte-Chapelle in Köln. Otto Bartnings Stahlkirche auf der Pressa 1928 T2 - Baugedanken: Einsichten, Ansichten, Aussichten für Jan Pieper zum 80. Geburtstag Y1 - 2024 SN - 978-3-943164-87-9 SP - 66 EP - 81 PB - Geymüller Verag für Architektur CY - Aachen ER - TY - GEN A1 - Roth, J. A1 - Tippkötter, Nils T1 - New Approach for Enzymatic Hydrolysis of Lignocellulose with Selective Diffusion Separation of the Monosaccharide Products T2 - Chemie Ingenieur Technik N2 - Enzymatic hydrolysis of lignocellulosic material plays an important role in the classical biorefinery approach. Apart from the pretreatment of the raw material, hydrolysis is the basis for the conversion of the cellulose and hemicellulose fraction into fermentable sugars. After hydrolysis, usually a solid-liquid separation takes place, in order to separate the residual plant material from the sugar-rich fraction, which can be subsequently used in a fermentation step. In order to factor out the separation step, the usage of in alginate immobilized crude cellulose fiber beads (CFBs) were evaluated. Pretreated cellulose fibers are incorporated in an alginate matrix together with the relevant enzymes. In doing so, sugars diffuse trough the alginate matrix, allowing a simplified delivery into the surrounding fluid. This again reduces product inhibition of the glucose on the enzyme catalysts. By means of standardized bead production the hydrolysis in lab scale was possible. First results show that liberation of glucose and xylose is possible, allowing a maximum total sugar yield of 75 %. Y1 - 2016 U6 - https://doi.org/10.1002/cite.201650301 SN - 0009-286X SN - 1522-2640 (eISSN) N1 - ProcessNet-Jahrestagung 2016 und 32. DECHEMA-Jahrestagung der Biotechnologen 2016, 12. - 15. September 2016, Eurogress Aachen VL - 88 IS - 9 SP - 1237 PB - Wiley-VCH CY - Weinheim ER - TY - GEN A1 - Wulfhorst, H. A1 - Merseburg, J. A1 - Tippkötter, Nils T1 - Batteriekomponenten aus nachwachsenden Rohstoffen T2 - Chemie Ingenieur Technik N2 - In diesem Beitrag geht es um die Integration von Stoffströmen einer Lignocellulose-Bioraffinerie in Verfahren zur Batterieherstellung. Pflanzliche Reststoffe aus der Biokraftstoffherstellung wie Lignin sollen zur Herstellung neuer Batteriematerialien verwendet werden. Hierbei wird das Lignin als Matrix für die vorgraphitischen C-haltigen Einlagerungsverbindungen in den Elektroden genutzt. Die Si-C-Komposite werden durch das Einbetten von Si in eine Ligninmatrix mit anschließender Carbonisierung hergestellt. Das Lignin hierfür wird durch die sequentielle hydrothermale Vorbehandlung von Buchenholz bei variablen Bedingungen gewonnen und mit Si-Nanopartikel sowie als Referenz ohne Si-Nanopartikel gefällt. Die Ergebnisse zeigen, dass die sequenzielle Vorbehandlung höhere Ausbeuten im Vergleich zum LHW- oder Organosolv-Aufschluss liefert. Um eine Anode herzustellen, wurde das resultierende Si–C-Kompositmaterial carbonisiert, auf einen Stromsammler aufgetragen und elektro-chemisch charakterisiert. Der Einfluss der Vorbehandlungsschritte auf den Herstellungsprozess und die ökonomische Bewertung des untersuchten Bioraffinerie-Prozesses wurde mithilfe eines Stoffstrommodells analysiert. Y1 - 2016 U6 - https://doi.org/10.1002/cite.201650333 SN - 0009-286X SN - 1522-2640 (eISSN) N1 - ProcessNet-Jahrestagung 2016 und 32. DECHEMA-Jahrestagung der Biotechnologen 2016, 12. - 15. September 2016, Eurogress Aachen VL - 88 IS - 9 SP - 1234 EP - 1235 PB - Wiley-VCH CY - Weinheim ER - TY - GEN A1 - Poth, S. A1 - Monzon, M. A1 - Tippkötter, Nils A1 - Ulber, Roland T1 - Lignocellulose-Bioraffinerie: Simultane Verzuckerung und Fermentation T2 - Chemie Ingenieur Technik N2 - Die am häufigsten genutzten Rohstoffe für die Produktion von Treibstoffen und Chemikalien sind fossilen Ursprungs. Da diese limitiert sind, werden im Hinblick auf die Nachhaltigkeit alternative, erneuerbare Rohstoffquellen intensiv untersucht. Vielversprechend in diesem Kontext sind die in Lignocellulose enthaltenen Zucker, die beispielsweise zur Produktion von Ethanol genutzt werden können. In der Regel sind für eine Lig-nocellulose-Bioraffinerie mehrere Prozessschritte notwendig: Vorbehandlung, Verzuckerung und Fermentation. Um diesen Prozess einfacher zu gestalten, ist es möglich, die Verzuckerung und die Fermentation in einem Schritt durchzuführen (SSF). Als Substrat wird hier Cellulose-Faserstoff verwendet, der durch das Organosolv-Verfahren aufgeschlossen wurde. Die Hydrolyse erfolgt mit kommerziell erhältlichen Enzymen und für die Fermentation zu Ethanol werden zwei Hefen verwendet. Beim SSF-Verfahren konnte, im Vergleich zur entkoppelten Verfahrensweise, trotz bestehender Unterschiede in den Temperatur-Optima von Enzymen und Hefen eine Steigerung in der Ethanol-Ausbeute von 0,15 auf 0,2 gg⁻¹ beobachtet werden. Um wirtschaftliche Ausbeuten und Konzentrationen des Produkts erzielen zu können, ist es notwendig den Prozess weiter zu optimieren. Im Einzelfall muss überprüft werden, ob diese Verfahrensweise auch für die Produktion anderer interessanter Stoffe (wie Itaconsäure, Bernsteinsäure) geeignet ist. KW - Lignocellulose-Bioraffinerie KW - Prozessintegration Y1 - 2010 U6 - https://doi.org/10.1002/cite.201050360 N1 - ProcessNet-Jahrestagung 2010 und 28. DECHEMA-Jahrestagung der Biotechnologen, 21. - 23. September 2010, Eurogress Aachen VL - 82 IS - 9 SP - 1568 PB - Wiley-VCH CY - Weinheim ER - TY - GEN A1 - Pasteur, A. A1 - Ludwig, B. A1 - Tippkötter, Nils A1 - Diller, R. A1 - Kampeis, P. A1 - Ulber, Roland T1 - Aufarbeitung von β-Lactamantibiotika mittels selektiver, magnetischer Adsorbermaterialien T2 - Chemie Ingenieur Technik N2 - b-Lactame gehören zu den wirkungsvollsten Antibiotika, jedoch lassen sich viele nur schwierig fermentativ erzeugen. Ein Problem bei der fermentativen Produktion ist die Hydrolyse des Lactamrings im wässrigen Milieu. Das Ziel des von der DBU geförderten Projekts ist die selektive In-situ-Adsorption der b-Lactamantibiotika unter anschließender magnetischer Separation. Durch die Isolation im Hochgradientenmagnetseparator (HGMS) ist eine Fest-fest-flüssig-Trennung und somit ein erheblicher Zeitgewinn im Downstreamprozess möglich. Zusätzlich kommt es zur Einsparung an Lösungsmittel und Energie, was neben Reduzierung der Antibiotikahydrolyse auch in ökologischer Hinsicht einen interessanten Aspekt darstellt. Als Trägermaterial für die Adsorbermatrix werden magnetisierbare Eisenoxidpartikel eingesetzt, die in einer Silikamatrix eingebettet sind. Diese Adsorber sollen auf Selektivität in Wasser und verschiedenen Medien getestet werden. Zusätzlich werden die Abbauprodukte des b-Lactams analysiert, um eine Aussage über die Stabilisierung des Antibiotikums durch die selektiven Adsorber treffen zu können. Diese Ergebnisse werden mit kommerziell erhältlichen Adsorbern verglichen. Die Aufreinigung der Antibiotika soll direkt aus der Fermentationsbrühe erfolgen. Um die Trennung der magnetischen, selektiven Adsorber von der Biomasse zu gewährleisten, soll der HGMS in die Fermentation integriert werden. Das filamentöse Wachstum des Mikroorganismus erfordert eine Neuauslegung der Filtermatrix. KW - β-Lactame KW - Magnetische Adsorbermaterialien Y1 - 2010 U6 - https://doi.org/10.1002/cite.201050270 N1 - ProcessNet-Jahrestagung 2010 und 28. DECHEMA-Jahrestagung der Biotechnologen, 21. - 23. September 2010, Eurogress Aachen VL - 82 IS - 9 SP - 1587 PB - Wiley-VCH CY - Weinheim ER - TY - GEN A1 - Tippkötter, Nils A1 - Zhang, M. A1 - Poth, S. A1 - Ulber, Roland T1 - Enzymatische Lignindegradierung unter Einsatz eines Optimierungsalgorithmus T2 - Chemie Ingenieur Technik N2 - Lignine bestehen aus einem hochgradig vernetzten Polymer phenolischer Grundeinheiten. Diese Verbindungen sind eine Quelle vielversprechender chemischer Grundbausteine. Auch die enzymatische Modifikation der Materialeigenschaften des Lignins ist für dessen Anwendung von Interesse. Aufgrund der verschiedenen Bindungstypen im Lignin ist eine Auftrennung mit nur einem Enzym unwahrscheinlich. Vielmehr sind verschiedene mediatorgestützte Reaktionen notwendig. Pilze, wie z.B. T. versicolor, nutzen Enzymkombinationen zum Aufschluss des Lignins. Hierbei kommen Laccase, Ligninperoxidase und Manganperoxidase zum Einsatz. Die optimale Kombination der Enzyme und ihrer Mediatoren bzw. Stabilisatoren ist Ziel der Untersuchungen. Aufgrund der großen Parameteranzahl wurde ein genetischer Algorithmus eingesetzt. Als Versuchsparameter wurden gewählt: die Verhältnisse der Enzyme, Ligninmasse, Konzentrationen an Eisen-, Mangan-, Oxalat-Ionen, ABTS, Violursäure und H₂O₂. Somit werden elf Parameter simultan optimiert. Als Algorithmus wurde ein Programm mit variabler Genkodierung entwickelt. Die Umsetzung des Lignins wird dabei über den verfolgt. Zurzeit ist ein enzymatischer Umsatz von 12% möglich. Als Referenz wurde eine chemische Lignindegradierung mit einem Umsatzvon 37% etabliert. Die sechs Generationen des Algorithmus zeigen eine Kongruenz der Enzymkonzentrationen von LiP, MnP und VeP, während Laccase keinen Einfluss hat. Des Weiteren beeinflussen die Konzentrationen von Mangan und Oxalat die Umsetzung, während die Variation von ABTS- und H₂O₂ nur eine geringe Auswirkung hat. KW - Enzymatischer Ligninabbau KW - Genetischer Algorithmus Y1 - 2010 U6 - https://doi.org/10.1002/cite.201050707 SN - 0009-286X SN - 1522-2640 (eISSN) N1 - ProcessNet-Jahrestagung 2010 und 28. DECHEMA-Jahrestagung der Biotechnologen, 21. - 23. September 2010, Eurogress Aachen VL - 82 IS - 9 SP - 1601 EP - 1602 PB - Wiley-VCH CY - Weinheim ER - TY - GEN A1 - Staub, C. A1 - Tippkötter, Nils A1 - Suck, K. A1 - Sohling, U. A1 - Ulber, Roland T1 - Chromatographische Aufarbeitung von Molkekonzentrat mittels mineralischer Granulate T2 - Chemie Ingenieur Technik N2 - Molke fällt im Rahmen der Käseherstellung allein in Deutschland in Mengen von über 11 Mio. Tonnen jährlich an. Dieses Nebenprodukt wurde trotz seines Reichtums an Milchzucker und Proteinen lange Zeit kaum industriell weiterverarbeitet und stellte ein bedeutendes Problem bei der Abwasserreinigung dar. Derzeit kommen meist kosten- und reinigungsintensive Membranfiltrationsverfahren bei der Auftrennung von Molke in ihre Hauptkomponenten Lactose und Molkenprotein zum Einsatz. Die Produkte finden vorwiegend in der Nahrungsmittelindustrie Anwendung als Süßungsmittel, Proteinzusatz oder Texturbildner. Die Mehrheit des Proteins wird dabei als Konzentrat bzw. Proteinpulver verarbeitet. Wegen der antibakteriellen, antiviralen und weiteren wertvollen physiologischen Eigenschaften der Molkeproteine stellt eine weitere Aufreinigung der einzelnen Molkeproteine für die pharmazeutische Industrie einen naheliegenden zusätzlichen Wertschöpfungsschritt dar. In Kooperation mit der Süd Chemie AG wurde damit begonnen, ein Verfahren zu entwickeln, das kostengünstige mineralische Adsorbentien verwendet. Bisher konnte die Abtrennung von Lactose von den Molkenproteinen aus verdünntem Molkekonzentrat in einem Verfahrensschritt ohne Vorbehandlung des Rohstoffs erfolgreich realisiert werden. Aktuelle Arbeiten beschäftigen sich mit der Verbesserung der Proteinbindekapazitätund chromatographischen Proteinauftrennung sowie dem Upscaling zum direkten Einsatz von Molkekonzentrat ohne Vorverdünnung. KW - Adsorbentien KW - Molkenprotein Y1 - 2010 U6 - https://doi.org/10.1002/cite.201050322 SN - 0009-286X SN - 1522-2640 (eISSN) N1 - ProcessNet-Jahrestagung 2010 und 28. DECHEMA-Jahrestagung der Biotechnologen, 21. - 23. September 2010, Eurogress Aachen VL - 82 IS - 9 SP - 1588 EP - 1589 PB - Wiley-VCH CY - Weinheim ER - TY - GEN A1 - Staub, C. A1 - Tippkötter, Nils A1 - Suck, K. A1 - Ruf, F. A1 - Sohling, U. A1 - Ulber, Roland T1 - Aufreinigung von Molkeproteinen mittels natürlicher Adsorbermaterialien T2 - Chemie Ingenieur Technik N2 - Molke als Nebenprodukt der Käseherstellung wurde lange Zeit als Abfall betrachtet. Bedingt durch ihren hohen BOD (biological oxygen demand) war die direkte Einleitung in Gewässer, aber auch der mikrobielle Abbau in Kläranlagen bedenklich. Falls eine Weiterverarbeitung der Molke stattfand, so geschah dies meist zu Molkepulver oder Proteinkonzentrat. Als Untersuchungen der Molkeproteine jedoch unter pharmazeutischen Gesichtspunkten interessante Eigenschaften nahelegten, stieg das Interesse am Bioprodukt Molke und ihren Proteinen an. So stehen beispielsweise für die Molkeproteine a-Lactalbumin (ala) und b-Lactoglobulin (blg) antibakterielle, anticancerogene und diverse andere physiologische Effekte in der Diskussion. Gegenwärtig finden meist Membranverfahren zur Aufreinigung von Molkeproteinen Anwendung. Als alternatives Verfahren wurde am Institut für Bioverfahrenstechnik in Kaiserslautern ein chromatographisches Verfahren entwickelt, bei dem natürliche Tonminerale zum Einsatz kamen. Nach chemischer und physikalischer Modifikation des Ausgangsmaterials durch den Hersteller Süd-Chemie wurden drei der Adsorber für nähere Untersuchungen zur Auftrennung von Molkeproteinen aus Molkekonzentrat herangezogen. Nach einer Cross-Flow-Filtration des Molkekonzentrats erfolgte die Aufreinigung der Molkeproteine in einem FPLC-System. Y1 - 2009 U6 - https://doi.org/10.1002/cite.200950310 SN - 0009-286X SN - 1522-2640 (eISSN) N1 - ProcessNet‐Jahrestagung 2009 und 27. DECHEMA-Jahrestagung der Biotechnologen, 8.- 10. September 2009, Mannheim VL - 81 IS - 8 SP - 1299 PB - Wiley-VCH CY - Weinheim ER - TY - GEN A1 - Poth, S. A1 - Monzon, M. A1 - Tippkötter, Nils A1 - Ulber, Roland T1 - Enzymatische Hydrolyse von vorbehandelter Lignocellulose T2 - Chemie Ingenieur Technik N2 - Die ökonomische Abhängigkeit von fossilen Brennstoffen und der klimatische Wandel durch die Nutzung dieser haben zu einer intensiven Suche nach erneuerbaren Rohstoffen für die Produktion von Chemikalien und Treibstoffen geführt. Ein viel versprechender Rohstoff in diesem Zusammenhang sind Zucker, die mittels enzymatischer Hydrolyse aus Lignocellulose gewonnen und beispielsweise zu Ethanol umgesetzt werden können. Dabei ist es notwendig die Hydrolyse in Hinsicht auf das verwendete Substrat und die Verwendung der entstehenden Hydrolysate für die Fermentation von Alkohol zu optimieren. Als Substrat dienen Cellulose- und Hemicellulose-Fraktionen, die durch thermo-chemische Vorbehandlung von Holz gewonnen werden. Die Vorbehandlung erfolgt bei unserem Projektpartner am Johann Heinrich von Thünen Institut in Hamburg. Verschiedene kommerziell erhältliche Enzyme, thermostabile eingeschlossen, wurden auf ihre Fähigkeit hin untersucht, diese Fraktionen zu den entsprechenden Zuckern umsetzen zu können. Um die Konzentration an fermentierbaren Zuckern zu steigern werden verschiedene Optimierungen durchgeführt, z. B. die Erhöhung der Substrat- bzw. Enzymkonzentrationen. Ein weiterer interessanter Ansatz, welcher ebenfalls verfolgt wird, ist es die Hydrolyse und die Fermentation in einem Schritt durchzuführen. Y1 - 2009 U6 - https://doi.org/10.1002/cite.200950244 SN - 0009-286X SN - 1522-2640 (eISSN) N1 - ProcessNet‐Jahrestagung 2009 und 27. DECHEMA-Jahrestagung der Biotechnologen, 8.- 10. September 2009, Mannheim N1 - Das hier vorgestellte Vorhaben wird durch die Fachagentur für Nachwachsende Rohstoffe (FNR) gefördert: „Verbundvorhaben: Pilotprojekt Lignocellulose-Bioraffinerie, Teilvorhaben 1: Extraktverarbeitung, Enzymtechnologie, verfahrenstechnische Untersuchungen, Ökobilanzierung, Wirtschaftlichkeitsberechnungen“ (Förderkennzeichen: FNR 22027405) VL - 81 IS - 8 SP - 1049 PB - Wiley-VCH CY - Weinheim ER - TY - GEN A1 - Tippkötter, Nils A1 - Wiesen, S. A1 - Thiel, A. A1 - Muffler, K. A1 - Ulber, Roland T1 - Biotechnologische Wertstoffgewinnung entlang der Prozessketten Grüner und Pflanzenöl-Bioraffinerien T2 - Chemie Ingenieur Technik N2 - Der nachwachsende Rohstoff Raps ist in großen Mengen verfügbar und eine Quelle für Biomoleküle mit hohem Wertschöpfungspotenzial. Entwicklungen zur biotechnologischen Wertstoffgewinnung werden dabei schwerpunktmäßig in den Bereichen Aufarbeitung und Funktionalisierung von Polyphenolen und Fetten betrieben. Bei der Verarbeitung der Pflanzenmaterialien werden dabei insbesondere Verfahren zur adsorptiven Aufreinigung und Auftrennung mittels Materialien mit modifizierten Bleicherden und anderen organischen oder anorganischen Adsorbentien untersucht. Ferner wurden für die Aufreinigung von Polyphenolen adsorptive sowie extraktive Prozesse entwickelt. Bei den Entwicklungen wird berücksichtigt, dass Bioraffinerien auf eine fortwährende Gewährleistung eines hohen Produktions- bzw. Lieferbedarfs nachwachsender Rohstoffe angewiesen sind. Somit werden Optionen dezentraler regionaler Vorbehandlungs- und Wertschöpfungsketten in der Nähe landwirtschaftlicher Betriebe einbezogen. Neben neuen Aufreinigungsverfahren werden mikrobielle und enzymatische Prozesse zur wertsteigernden Umsetzung von Glycerin, Polyphenolen und Zuckermonomeren vorgestellt sowie Limitierungen nachwachsender Rohstoffe der 2. Generation diskutiert. Y1 - 2014 U6 - https://doi.org/10.1002/cite.201450283 SN - 0009-286X SN - 1522-2640 (eISSN) N1 - ProcessNet-Jahrestagung 2014 und 31. DECHEMA-Jahrestagung der Biotechnologen, 30. September - 2. Oktober 2014, Eurogress Aachen N1 - Diese Arbeiten werden vom Bundesministerium für Ernährung und Landwirtschaft durch den Projektträger FNR e. V. im Rahmen des Projekts FKZ22022908 gefördert VL - 86 IS - 9 SP - 1605 PB - Wiley-VCH CY - Weinheim ER - TY - GEN A1 - Wollny, S. A1 - Al-Kaidy, H. A1 - Tippkötter, Nils A1 - Ulber, Roland T1 - Prozessintegrierte Magnetseparation im Labormaßstab mittels High-Gradient Magnetic Separator (HGMS) T2 - Chemie Ingenieur Technik N2 - Die Hochgradient-Magnetseparation (HGMS) stellt eine Alternative zu konventionellen Methoden der Proteinaufarbeitung wie Filtration und Chromatographie dar und dient zudem als Prozessintensivierung. Bisherige Separatoren sind für Anwendungen von mehreren Litern Prozessvolumina Fermentationsmedium und Gramm Magnetpartikel ausgelegt. Bei der Entwicklung und Anwendung neuartiger Magnetpartikeloberflächen ist die Verfügbarkeit großer Mengen nicht gegeben. Bisherige Filterkammern erhöhen zudem den Arbeitsaufwand und verursachen größere Partikelverluste bei Spülvorgängen oder der Reinigung aufgrund der Partikeladsorption. Für Anwendungen im Maßstab < 500 mL wird deshalb ein Miniatur-Hochgradientfilter (miniHGF) entwickelt. Das Modell wird im 3D-Drucker Makerbot Replicator 2 gefertigt und magne-isierbare Drähte zur Partikelabscheidung eingesetzt. Die Vergleichbarkeit mit einem etablierten Magnetseparator wird anhand der Aufnahme von Durchbruchskurven und Bestimmung der Filtereffizienz untersucht. Die Praxistauglichkeit mit kleinen Volumina wird in wiederholten Batch-Versuchen mit auf Magnetpartikeln immobilisiertem Enzym und einem kolorimetrischen Assay geprüft. Y1 - 2014 U6 - https://doi.org/10.1002/cite.201450618 SN - 0009-286X SN - 1522-2640 (eISSN) N1 - ProcessNet-Jahrestagung 2014 und 31. DECHEMA-Jahrestagung der Biotechnologen, 30. September - 2. Oktober 2014, Eurogress Aachen VL - 86 IS - 9 SP - 1507 PB - Wiley-VCH CY - Weinheim ER - TY - GEN A1 - Tippkötter, Nils A1 - Duwe, Anna A1 - Rais, Dominik A1 - Zibek, Susanne A1 - Zorn, H. T1 - Optimierung und Scale-up der enzymatischen Hydrolyse inkl. Ligninabbau T2 - Chemie Ingenieur Technik N2 - Primäre Ziele der Hydrolyse pflanzlicher nachwachsender Rohstoffe sind möglichst hohe Zuckerkonzentrationen für nachfolgende Fermentationen und eine Maximierung der Produktivität. Zur Optimierung dieser Prozesse wird Organosolv-aufgeschlossene Buchenholz-Cellulose verwendet. Die Hydrolyse des Faserstoffes erfolgt mithilfe von Novozymes CTec2-Enzymen. Die Hydrolysen konnten durch neue Rührerelemente auf einen Maßstab von 1000 L übertragen werden. Dabei konnten maximale Ausbeuten (g Glucose g –1 Glucose im Faserstoff) bis 81 g g – 1 und Konzentrationen von 152 g L –1 erreicht werden. Zurzeit können unter Einsatz eines Feststoffreaktors Cellulosefasern in einer Konzentration bis 400 g L –1 enzymatisch hydrolysiert werden. Die cellulolytischen Enzyme stoßen bei hohen Feststoffkonzentrationen an ihre Grenzen. Mit steigendem Feststoffgehalt nimmt die Hydrolyseausbeute ab. Ein Ansatz zur Steigerung der Effizienz ist der Einsatz ligninolytischer Enzyme, die Ligninreste an der Organosolv-Cellulose aufschließen können. Eine solche Verbesserung der Zugänglichkeit für cellulolytische Enzyme an ihr Substrat wurde durch Kulturüberstände verschiedener ligninolytischer Pilze erreicht. Mit Kulturüberständen von Stereum sp. sind Steigerungen der Glucoseausbeuten um bis zu 30 % möglich. Y1 - 2014 U6 - https://doi.org/10.1002/cite.201450287 SN - 0009-286X SN - 1522-2640 (eISSN) N1 - ProcessNet-Jahrestagung 2014 und 31. DECHEMA-Jahrestagung der Biotechnologen, 30. September - 2. Oktober 2014, Eurogress Aachen N1 - Förderung vom Bundesministeriumfür Ernährung und Landwirtschaftdurch den Projektträger FNR e. V. im Rahmen des Projekts FKZ 22019409 VL - 86 IS - 9 SP - 1515 PB - Wiley-VCH CY - Weinheim ER - TY - GEN A1 - Hering, T. A1 - Pasteur, A. A1 - Wollny, S. A1 - Ulber, Roland A1 - Tippkötter, Nils T1 - Magnetische Separation von Gold-Nanopartikeln zur Gluconsäure-Produktion durch Hochgradient-Magnetseparation im Labormaßstab T2 - Chemie Ingenieur Technik N2 - Bei der Verarbeitung nachwachsender Rohstoffe entsteht aus Cellulose oder Stärke u. a. das wichtige Produkt Glucose. Diese niedermolekulare Kohlenhydratquelle wird üblicherweise als Substrat für biotechnologische und chemische Synthesen verwendet. Ein wirtschaftlich interessantes Oxidationsprodukt der Glucose ist Gluconsäure, die beispielsweise als Lebensmittelzusatzstoff (E 574), in der Medizin und Metallindustrie Verwendung findet. Die Umsetzung des Monosaccharids zu Gluconsäure erfolgt entweder durch mikrobielle Fermentation oder der Oxidation an heterogenen Katalysatoren. Die Zielsetzung der Studie ist die Untersuchung der Glucoseoxidation an magnetisierbaren Gold-Nanopartikeln unter nachfolgender Bypass-Separation des Katalysators mittels einer neuen Mini-HGMS-Einheit (Hochgradient-Magnetseparation). Dieser Filtertyp ermöglicht die selektive Trennung magnetischer Partikel aus Suspensionen mit hohem Feststoffgehalt oder Viskosität. Erste Ergebnisse zeigen eine Beladungskapazität des selbstkonstruierten Mini-HGMS von 550 mg goldbeschichteter magnetisierbarer Nanopartikel. Die Oxidation erfolgt bei einem pH-Wertvon 9, bei 40 °C und mit 100 mM Glucose in einem begasten Rührkesselreaktor. Das System soll zukünftig zum Katalysatorrecycling von hochviskosen und Feststoffbelasteten Produktströmen aus Bioraffinerien eingesetzt werden. Y1 - 2014 U6 - https://doi.org/10.1002/cite.201450265 SN - 0009-286X SN - 1522-2640 (eISSN) N1 - ProcessNet-Jahrestagung 2014 und 31. DECHEMA-Jahrestagung der Biotechnologen, 30. September - 2. Oktober 2014, Eurogress Aachen VL - 86 IS - 9 SP - 1501 PB - Wiley-VCH CY - Weinheim ER - TY - GEN A1 - Hering, T. A1 - Ulber, Roland A1 - Tippkötter, Nils T1 - Aktiver und passiver antimikrobieller Oberflächenschutz durch funktionalisierte Mikropartikel T2 - Chemie Ingenieur Technik N2 - Mikrobielle Verunreinigungen von Oberflächen in technischen und medizinischen Systemen sind allgegenwärtig. Sie basieren üblicherweise auf adsorptiven Oberflächenbindungen organischer Komponenten (Proteine und Fette) oder Membrankomponenten aerogener sowie wassergebundener Mikroorganismen. In laufenden Forschungsarbeiten wird eine aktive sowie passive Biomodifikation von Oberflächen zu deren Schutz vor Adsorption von Proteinen und Mikroorganismen verfolgt. Der antimikrobielle Schutz soll dabei sowohl durch die Mikrostrukturierung bzw. Rauheitsanpassung der Oberflächen durch deren Beschichtung mit Mikro-und Nanopartikeln erfolgen. Ferner werden antimikrobielle Enzyme und funktionelle Gruppen auf den Mikropartikeln gebunden, um den Oberflächenschutz zu verstärken. In ersten Versuchen wurden quartäre Ammoniumverbindungen auf eigens synthetisierten superparamagnetischen Eisenoxid-Nanopartikeln (Durchmesser 10 – 30 nm) immobilisiert und die wachstumshemmende Wirkung untersucht. Erste Ergebnisse zeigten, dass eine Konzentration von 10 mg mL⁻¹ der Ammoniumverbindung in einer Wachstumshemmung des verwendeten Gram-negativen Modell-Mikroorganismus E. coli GFPmut2 resultiert. Zurzeit werden synergistisch wirkende Kombinationen von Partikeln mit Proteasen, quartären Ammoniumverbindungen, hydrophoben Oberflächen und mikrostrukturierten Oberflächen als antimikrobieller Schutz untersucht. Y1 - 2014 U6 - https://doi.org/10.1002/cite.201450264 SN - 0009-286X SN - 1522-2640 (eISSN) N1 - ProcessNet-Jahrestagung 2014 und 31. DECHEMA-Jahrestagung der Biotechnologen, 30. September - 2. Oktober 2014, Eurogress Aachen VL - 9 IS - 86 SP - 1474 EP - 1475 PB - Wiley-VCH CY - Weinheim ER - TY - GEN A1 - Al-Kaidy, H. A1 - Tippkötter, Nils A1 - Kaiser, P. A1 - Wollny, S. A1 - Ulber, Roland T1 - Aufreinigung von Cytochrom P450BMP mittels magnetischer Partikel und die enzymatische Synthese von 9, 10-Dihydroxystearinsäure T2 - Chemie Ingenieur Technik N2 - Cytochrom P450 sind Häm-Proteine, die zur Enzymklasse der Oxidoreduktasen (EC 1.14.xy) gehören. Eine wichtige Reaktion ist die Hydroxylierung nichtaktivierter C–H-Bindungen, die in technischen Systemen von großem Interesse ist. Durch die Verwendung von M-IDA-2-Partikeln ist eine direkte Aufreinigung mit gleichzeitiger Immobilisierung und die Applikation der Enzyme aus dem Zelllysat möglich. Damit ist das Verfahren mehr als fünf Stunden schneller als die konventionelle Chromatographie und mehr als 80 % der Aufreinigungszeit wird gespart. Mit dem isolierten nativen Enzym konnte die Plattformchemikalie 9,10-Dihydroxystearinsäure aus Ölsäure hergestellt werden. Unter anderem für die Kunststoffindustrie können aus diesem Produkt wichtige Monomere wie z. B. Azelainsäure hergestellt werden. Die Bildung des Produkts erfolgt in einem zweiphasigen Reaktionssystem an der Grenzfläche zwischen dem Öl und der wässrigen Phase als Feststoff. Um das immobilisierte Enzym aktiv in die obere Phase zu transportieren, wurde eine neue magnetische Mischvorrichtung entwickelt. Das Reaktionsprodukt wurde mit NMR, GC-MS und HPLC-MS analysiert und mit einem chemisch synthetisierten Standard von 9,10-Dihydroxystearinsäure verglichen. Derzeit werden Studien des immobilisierten Häms des Enzyms durchgeführt. Y1 - 2014 U6 - https://doi.org/10.1002/cite.201450420 SN - 0009-286X SN - 1522-2640 (eISSN) N1 - ProcessNet-Jahrestagung 2014 und 31. DECHEMA-Jahrestagung der Biotechnologen, 30. September - 2. Oktober 2014, Eurogress Aachen N1 - Gefördert wird dieses Projekt im Rahmen von MAGNENZ durch das BMBF VL - 86 IS - 9 SP - 1420 PB - Wiley-VCH CY - Weinheim ER - TY - GEN A1 - Al-Kaidy, H. A1 - Ulber, Roland A1 - Tippkötter, Nils T1 - Eine Plattform-Technologie für die automatisierte Reaktionsführung in magnetisierbaren mikrofluidischen Tropfen T2 - Chemie Ingenieur Technik N2 - Üblicherweise werden biotechnologische Reaktionssysteme im mikrofluidischen Maßstab in vorstrukturierten Bauteilen oder mit auf Wellplatten basierenden Robotersystemen realisiert. In dem hier vorgestellten System werden chemische oder biologische Reaktionen mit magnetischen Mikroreaktoren (MR) durchgeführt, bei denen hydrophobe magnetische Mikropartikel einen wässrigen Kern umschließen. Solche MR bieten eine gute Kontrolle der Reaktionsbedingungen, eine verbesserte Sicherheit und Portabilität. Die neue Plattformtechnologie ermöglicht die zweidimensionale Bewegung der magnetischen MR auf einer planaren Ebene. Oberhalb oder unterhalb der Plattform werden Magnetfeldgradienten zum Manipulieren und Bewegen eines oder mehrerer magnetischer MR erzeugt. Die optimal auf die MR wirkenden magnetischen Kräfte werden experimentell ermittelt und simuliert. Die Aktivierung der Magnetfelder wird automatisiert durch elektrische Spulen mit Eisenkern bzw. Neodymmagnet gesteuert. Angewendet wurde das System beim reversiblen Öffnen von MR, um z. B. Reaktionspartner in den wässrigen Kern zu injizieren oder Proben zu entnehmen. Ferner wurde Lac-case A und b-Glucosidase auf einer Quarzglasoberfläche immobilisiert und mit einem MR zum Reagieren gebracht. Weiterhin wurden MR fusioniert und so ein wässriger Kern bestehend aus Laccase mit einem aus dem entsprechenden Substrat Syringaldazin vereint. Y1 - 2014 U6 - https://doi.org/10.1002/cite.201450424 SN - 0009-286X SN - 1522-2640 (eISSN) N1 - ProcessNet-Jahrestagung 2014 und 31. DECHEMA-Jahrestagung der Biotechnologen, 30. September - 2. Oktober 2014, Eurogress Aachen VL - 86 IS - 9 SP - 1419 EP - 1420 PB - Wiley-VCH CY - Weinheim ER - TY - GEN A1 - Stadtmüller, R. A1 - Tippkötter, Nils A1 - Ulber, Roland T1 - Produktion von einzelsträngigen DNA-Makronukleotiden T2 - Chemie Ingenieur Technik N2 - In der Biotechnologie stellt Einzelstrang-DNA (ssDNA) eine Schlüsselrolle dar und fungiert z. B. als Baustein für die nanoskalige Feinmechanik oder als Affinitätsligand, ein sog. Aptamer. Hinsichtlich der industriellen Verwendung bieten Aptamere im Vergleich zu Antikörpern viele Vorteile, wie z. B. eine gute Renaturierung bzw. die Selektion für cytotoxische Moleküle. Aktuell wächst die Nachfrage für chimäre Aptamere von bis zu 200 n, um die simultane Bindung bzw. die Modifikation mehrerer Moleküle zu realisieren. Bis heute wird ssDNA mittels einer sequentiellen Synthese hergestellt, die eine Effizienz von ca. 99,5 % je Zyklus und bereits bei einer Produktlänge von 100 n nur noc hAusbeuten von max. 60 % zeigt. Um dem Bedarf an ssDNA im Bereich > 100 n zu entsprechen, wurden zwei enzymatische Verfahren zur Produktion dieser Makronukleotide entworfen. Die erste Technik basiert auf einerFestphasen-PCR und ermöglicht sowohlein Primer- als auch ein Templatrecycling. Das zweite Verfahren beruht auf einer Plasmidbasierten In-vivo-Amplifikation, der sog. AptaGENE®-Technologie. In einer einzigen Klonierung werden bis zu 100 Kopien des Monomers in einen Vektor kloniert. Nach einer Transformation folgt der reguläre Produktionsprozess in Form einer Kultivierung, Plasmidpräparation und sequenziellen Aufarbeitung von bis zu 6 · 10¹⁵ Makronukleotiden pro Milliliter Fermentationsvolumen. Y1 - 2014 U6 - https://doi.org/10.1002/cite.201450372 SN - 0009-286X SN - 1522-2640 (eISSN) N1 - ProcessNet-Jahrestagung 2014 und 31. DECHEMA-Jahrestagung der Biotechnologen, 30. September - 2. Oktober 2014, Eurogress Aachen VL - 86 IS - 9 SP - 1403 PB - Wiley-VCH CY - Weinheim ER - TY - GEN A1 - Tippkötter, Nils A1 - Roth, J. A1 - Möhring, M. A1 - Wulfhorst, H. A1 - Ulber, Roland T1 - Verwertung von Bioraffinerie-Stoffströmen am Beispiel von Einzellerproteinen T2 - Chemie Ingenieur Technik N2 - Die Nutzung von Biomasse aus pflanzlichen Abfällen für die stoffliche Verwertung rückt immer stärker in den Vordergrund. Dabei ist vor allem die ganzheitliche Verwertung der Stoffströme von Bedeutung, da diese einen integrativen Ansatz ermöglichen. Im Rahmen dieser Arbeit wird die Produktion von Einzellerproteinen (Single-Cell Proteins, SCPs) mithilfe von unterschiedlichen Rohsubstraten dargelegt. Somit können Reststoffströme, die in keiner Konkurrenz zur Produktion von Lebensmitteln stehen, für die Herstellung von Futter- und auch Nahrungsmitteln Verwendung finden. Die zunächst thermisch vorbehandelten Ausgangsmaterialien stammen aus forstwirtschaftlichen und grünen Abfällen und ermöglichen durch eine anschließende enzymatische Hydrolyse die Freisetzung von Monosacchariden. Aus diesen erfolgt die SCP-Produktion fermentativ mithilfe der drei Modellorganismen Bakterium, Hefe und Pilz. Hierfür wird sowohl das flüssige Hydrolysat als auch der feste Reststoff auf der Basis einer Feststofffermentation genutzt. Auf diese Weise ist eine vollständige Verwertung der Ausgangsmaterialien möglich. Mit den gewonnen Daten erfolgt abschließend eine Bewertung der SCPs aus nachwachsenden Rohstoffen als alternative Proteinquelle. Y1 - 2014 U6 - https://doi.org/10.1002/cite.201450257 SN - 0009-286X SN - 1522-2640 (eISSN) N1 - ProcessNet-Jahrestagung 2014 und 31. DECHEMA-Jahrestagung der Biotechnologen, 30. September - 2. Oktober 2014, Eurogress Aachen VL - 86 IS - 9 SP - 1399 EP - 1400 PB - Wiley-VCH CY - Weinheim ER - TY - GEN A1 - Duwe, A. A1 - Sieker, T. A1 - Tippkötter, Nils A1 - Ulber, Roland T1 - Grasssilage als Substrat zur fermentativen Produktion organischer Säuren T2 - Chemie Ingenieur Technik N2 - Der zunehmende Bedarf an fossilen Rohstoffen bei gleichzeitig abnehmender Versorgungssicherheit führt zu einer intensiven Suche nach erneuerbaren Ressourcen. Ein vielversprechendes Ausgangsmaterial mit einer weltweiten Verfügbarkeit stellt Gras dar. In 2012 wurden in Deutschland 33 Millionen Tonnen (Heugewicht) Gras auf 4,82 Millionen Hektar Ackerland produziert, davon wurden 60,5 % siliert. Durch die Silierung kann Gras als Substrat zeitlich uneingeschränkt verfügbar sein, ohne dem Risiko des schnellen Verderbs ausgesetzt zu sein. Eine Schlüsselrolle im Rahmen des Silierprozesses nimmt die Produktion von Milchsäure ein. Milchsäure ist einbedeutendes biotechnologisches Produkt für die Lebensmittel- und die chemische Industrie. Im Rahmen dieser Arbeit wird die vollständige Umwandlung der fermentierbaren Zucker in der Silage zu Milchsäure angestrebt, um die maximale Ausbeute der organischen Säure zu erreichen. Im ersten Verfahrensschritt wird die Silage gepresst und der erhaltene Presskuchen einer Liquid-Hot-Water-Behandlung unterzogen. Durch diese einfache Vorbehandlung können hohe Glucoseausbeuten im nachfolgenden SSF-Schritt bei gleichzeitig geringem Enzymeinsatz und Chemikalienverbrauch realisiert werden. Zur Aufreinigung der Milchsäure wurden extraktive und chromatographische Methoden untersucht. Y1 - 2014 U6 - https://doi.org/10.1002/cite.201450345 SN - 0009-286X SN - 1522-2640 (eISSN) N1 - ProcessNet-Jahrestagung 2014 und 31. DECHEMA-Jahrestagung der Biotechnologen, 30. September - 2. Oktober 2014, Eurogress Aachen VL - 86 IS - 9 SP - 1400 PB - Wiley-VCH CY - Weinheim ER - TY - GEN A1 - Tippkötter, Nils A1 - Möhring, S. T1 - Nutzung von Fäulepilzen für die selektive Gewinnung von Cellulose und Lignin aus nicht vorbehandelter lignocellulosehaltiger Biomasse T2 - Chemie Ingenieur Technik N2 - Einige Arten der Braun- und Weißfäulepilze sind in der Lage, selektiv entweder Lignin oder Cellulose im Holz abzubauen. Diese Pilze können für eine energiesparende Vorbehandlung lignocellulosehaltiger Biomasse für Bioraffinerien genutzt werden, ohne auf technisch aufwändige Aufschlussapparate zurückgreifen zu müssen. Weißfäulepilze bauen bevorzugt Lignin ab, wodurch die verbleibende Cellulose leichter für enzymatische Hydrolysen in das Monosaccharid Glucose zugänglich wird. Braunfäulepilze bauen dagegen Cellulose und Hemicellulose ab. Die Auswirkungen der Behandlung von Weizenstroh mit verschiedenen Pilzarten werden zurzeit untersucht. Dabei werden die Veränderung der enzymatischen Hydrolysierbarkeit des Substrats sowie die gebildeten Ligninderivate bestimmt. Detaillierte Betrachtungen der Biomasseveränderung werden mithilfe spezifischer Färbemethoden durchgeführt, durch die morphologische Veränderungen der Pflanzengewebe in der 3D-Lichtmikroskopie dargestellt werden können. Y1 - 2014 U6 - https://doi.org/10.1002/cite.201450353 SN - 0009-286X SN - 1522-2640 (eISSN) N1 - ProcessNet-Jahrestagung 2014 und 31. DECHEMA-Jahrestagung der Biotechnologen, 30. September - 2. Oktober 2014, Eurogress Aachen N1 - Diese Arbeit wird durch das Bundesministerium für Ernährung und Landwirtschaft über die FNR e.V. unter dem Projektnamen „Lokale Vorbehandlung nachwachsender Rohstoffe für Bioraffinerien“ gefördert (FKZ 22028411) VL - 86 IS - 9 SP - 1385 PB - Wiley-VCH CY - Weinheim ER - TY - GEN A1 - Tippkötter, Nils A1 - Wasserscheid, P. T1 - Rapid-Prototyping-Strukturen für ressourceneffiziente Prozesse in Chemie und Biotechnologie T2 - Chemie Ingenieur Technik N2 - Die Teilefertigung durch Rapid Prototyping (RP) verkürzt den Weg von der Idee bis zum Produkt, wobei unter anderem Optimierungszyklen in geringer Zeit durchlaufen werden können. Ferner eröffnen neue Entwicklungen in diesem Bereich die Möglichkeit individueller Produktionsverfahren. Im Unterschied zur klassischen Fertigung von Prototypen wird beim RP mit additiver Schichtfertigung (Additive Layer Manufacturing, ALM) gearbeitet. Je nach Methode werden Flüssigkeiten oder Pulver nach Vorgaben eines 3D-Computermodells sequentiell aufgetragen. Diese Verfahren existieren seit ca. 25 Jahren, jedoch sind seit kurzem ausgesprochen günstige Geräte verfügbar, die Objekte mit Genauigkeiten bis 20 lm fertigen können. Das RP hat in klinischen Anwendungsgebieten bzw. im Bereich des Tissue Engineering bereits vielfach Einzug gefunden. Aber auch chemisch-biotechnologische Entwicklungen können von den Verfahren profitieren. So wurden Mikrofluidiksysteme und Bioreaktoren bereits erfolgreich durch RP gefertigt. Durch ALM ist ebenso die Herstellung von Reaktionseinheiten aus biokompatiblen Materialien wie ionotropen Gelen möglich. Ferner sind sehr komplexe Strukturierungen von Oberflächen im Nanometerbereich realisierbar, die für die Auftragung heterogener Katalysatoren oder auch Mikroorganismen eingesetzt werden können. Auch der Bereich Reaktoren- und Apparatebau kann von den Fortschritten in der additiven Fertigung profitieren. Verfahren wie selektives Laser- oder Elektronenstrahlschmelzen erlauben es, metallische Komponenten in nahezu beliebigen Geometrien zu fertigen. Somit können Strukturen verwirklicht werden, die mit konventionellen Fertigungstechniken nur sehr schwer oder überhauptnicht herstellbar wären. Durch Anwendung von rechnergestützter Modellierung können optimale Strukturen identifiziert und additiv gefertigt werden. Eine anschließende katalytische Funktionalisierung der Oberfläche ermöglicht die Herstellung strukturierter Reaktoren mit maßgeschneiderten Eigenschaften. Y1 - 2014 U6 - https://doi.org/10.1002/cite.201450451 SN - 0009-286X SN - 1522-2640 (eISSN) N1 - ProcessNet-Jahrestagung 2014 und 31. DECHEMA-Jahrestagung der Biotechnologen, 30. September - 2. Oktober 2014, Eurogress Aachen VL - 86 IS - 9 SP - 1369 EP - 1370 PB - Wiley-VCH CY - Weinheim ER - TY - GEN A1 - Stadtmüller, R. A1 - Wollny, S. A1 - Tippkötter, Nils A1 - Ulber, Roland T1 - Amplifikation und Einsatz von ssDNA-Aptameren T2 - Chemie Ingenieur Technik N2 - Die wachsende Produktpalette von z. B. Pharmazeutika geht mit einer steigenden Nachfrage für hochsensitive/schonende Aufreinigungstechniken einher. Bisherige Verfahren führen oft zu geringer Reinheit und verminderter Bioaktivität, zeigen eine Limitation der Analytengröße oder bedingen dessen Modifikation. Durch die Kombination von mikroskaligen Magnetpartikeln und spezifisch wechselwirkenden Einzelstrang-DNA-Oligonukleotiden, den sog. ssDNA-Aptameren, sind eine höhere Selektivität/Reinheit und eine Automatisierung möglich. In diesem Kontext werden zum einen ssDNA-Amplifikationstechniken und zum anderen der praktische Einsatz von Aptameren in einer Magnetseparation vorgestellt. Die ssDNA-Synthese basiert auf einem In-vivo-dsDNA-Produktionsschritt mittels eines rekombinanten Escherichia coli. Die als High-copy-Plasmid organisierte Sequenz wird in vitro durch Kombination verschiedener enzymatischer Reaktionen in die funktionelle ssDNA überführt. Diese Technik bedingt nur minimale Instrumentierung bzw. Prozessregelung. Die zweite Synthesetechnik wird in Form eines In-vitro-Amplifikationsverfahrens realisiert und beruht auf dem Prinzip einer PCR (Potenzial zu einer Automatisierung bzw. Miniaturisierung). Die gewonnenen Aptamere werden im Anschluss in einem auf Magnetpartikeln basierten Trennverfahren zur Isolationvon 6xHis-tag-Proteinen bezüglich ihrer Eigenschaften untersucht. Y1 - 2012 U6 - https://doi.org/10.1002/cite.201250112 SN - 0009-286X SN - 1522-2640 (eISSN) N1 - ProcessNet-Jahrestagung 2012 und 30. DECHEMA-Jahrestagung der Biotechnologen, 10. – 13. September 2012, Karlsruhe VL - 84 IS - 8 SP - 1294 PB - Wiley-VCH CY - Weinheim ER - TY - GEN A1 - Wollny, S. A1 - Stadtmüller, R. A1 - Tippkötter, Nils A1 - Oster, J. A1 - Kampeis, P. A1 - Ulber, Roland T1 - Optimierung der selektiven Aufarbeitung von Proteinen mit Aptamer-funktionalisierten Magnetpartikeln T2 - Chemie Ingenieur Technik N2 - Die Herstellung pharmakologisch relevanter Proteine durch Mikroorganismen führt eine mehrstufige Aufarbeitung mit sich. Durch die Verwendung von Aptameren, kurzen einzelsträngigen DNA- oder RNA-Oligonukleotiden immobilisiert auf funktionalisierten, wiederverwendbaren Magnetpartikeln, können mehrere dieser Abtrennungsoperationen kombiniert und damit die Prozesskosten minimiert werden. Aufgrund der definierten dreidimensionalen Struktur können Aptamere kleine organische Moleküle hochspezifisch binden. Im vorgestellten Projekt wird die Aufarbeitung von His6-GFP als Modellprotein mithilfe der mit Aptamer funktionalisierten Magnetpartikel durchgeführt. In bisherigen Versuchen wurde die Bindung von Aptameren auf den magnetischen Partikeln sowie die Bindung des Modellproteins GFP auf den Partikeln optimiert. Des Weiteren wurden mehrere Strategien zur Elution des GFPs von den Partikeln verfolgt, um den Proteinertrag zu maximieren und die Partikel rezyklieren zu können. Die Untersuchung unspezifischer Bindungen von Zelltrümmern und Proteinen an die Magnetpartikel wurde mithilfe eines konfokalen Laser-Scanning-Mikroskops durchgeführt. Y1 - 2012 U6 - https://doi.org/10.1002/cite.201250031 SN - 0009-286X SN - 1522-2640 (eISSN) N1 - ProcessNet-Jahrestagung 2012 und 30. DECHEMA-Jahrestagung der Biotechnologen, 10. – 13. September 2012, Karlsruhe VL - 84 IS - 8 SP - 1203 PB - Wiley-VCH CY - Weinheim ER - TY - GEN A1 - Duwe, A. A1 - Tippkötter, Nils A1 - Leipold, D. A1 - Riemer, S. A1 - Zorn, H. A1 - Ulber, Roland T1 - Holzhydrolyse als Feststoffreaktion: Charakterisierung von Inhibitoren und Erhöhung der Ausbeute durch den Einsatz lignolytischer Enzyme T2 - Chemie Ingenieur Technik N2 - Der Erhalt möglichst hoher Zuckerkonzentrationen für nachfolgende Fermentationen und eine Steigerung der Produktivität sind Ziele der Hydrolyse bei hohen Feststoffkonzentrationen im Rahmen des Projekts „Lignocellulose Bioraffinerie“. Verwendet wird durch ein Organosolv-Verfahren aufgeschlossenes Buchenholz. Die Hydrolyse des Faserstoffes erfolgt mithilfe von CTec2-Enzymen (Fa. Novozymes). Zurzeit können unter Einsatz eines neuen Feststoffreaktors Cellulosefasern in einer Konzentration bis 400 g L⁻¹ enzymatisch hydrolysiert werden. Dabei werden Ausbeuten (g Glucose/g Cellulose im Faserstoff) bis 0,86 g g⁻¹ und Glucosekonzentrationenvon 120 g L⁻¹ erreicht. Ein Nachteil ist jedoch die hierbei auftretende Abnahme der Hydrolyseausbeuten. Zahlreiche Limitierungen bezüglich der Hydrolysierbarkeit von Lignocellulose werden zurzeit diskutiert und publiziert. Ziel der Untersuchungen ist die Identifizierung hydrolysehemmender Substanzen sowie die Erhöhung der Ausbeute an Zuckermonomeren durch den Einsatz lignolytischer Enzyme. Hierbei wird eine HPLC-MS-Methode zur Charakterisierung hemmender Substanzen eingesetzt, um potenzielle Inhibitoren zu erfassen. Y1 - 2012 U6 - https://doi.org/10.1002/cite.201250298 SN - 0009-286X SN - 1522-2640 (eISSN) N1 - ProcessNet-Jahrestagung 2012 und 30. DECHEMA-Jahrestagung der Biotechnologen, 10. – 13. September 2012, Karlsruhe VL - 84 IS - 8 SP - 1307 PB - Wiley-VCH CY - Weinheim ER - TY - GEN A1 - Wiesen, S. A1 - Tippkötter, Nils A1 - Muffler, K. A1 - Sohling, U. A1 - Ruf, F. A1 - Ulber, Roland T1 - Nutzung von Rohglycerin: Rohglycerin-Aufarbeitung, Herstellung von 1, 3-Propandiol und Rückgewinnung von Fettsäuren T2 - Chemie Ingenieur Technik N2 - Die fermentative Verwertung von Rohglycerin setzt je nach Herstellungsmethode und Produktionsorganismus eine Vorbehandlung des Glycerins zur Entfernung von Produktinhibitoren voraus. Durch den Einsatz von Hydrotalcit-Adsorbern können die im Rohglycerin enthaltenen Fettsäuren entfernt werden. Durch diese einfache Aufarbeitungsmethode ist ein mit reinem Glycerin vergleichbarer Umsatz von stark mit Fettsäuren verunreinigtem Rohglycerin zu 1,3-Propandiol (PDO) möglich. Die durch den Hydrotalcit gebundenen Fettsäuren lassen sich mit einem Ethanol-Wasser-Gemisch eluieren. Somit kann der Adsorber regeneriert und die Fettsäuren wieder der Wertschöpfungskette zugeführt werden. Im Fed-Batch-Experiment kann mit C. diolis eine PDO-Konzentration von über 50 g L⁻¹ unter Verwendung des aufgereinigten Rohglycerins erzielt werden. In der industriellen Produktion wird PDO momentan destillativ aufgearbeitet. Ein adsorptives Aufarbeitungsverfahren kann den Energiebedarf des Herstellungsprozesses drastisch senken. Auf der Suche nach einem geeigneten Material wurde ein Adsorberscreening in Bezug auf die Bindungseigenschaften durchgeführt. Mit einem b-Zeolith der Firma Süd ChemieAG konnte bisher die höchste Beladung im Modellsystem von 120 mg PDO/gAdsorber erreicht werden. Y1 - 2012 U6 - https://doi.org/10.1002/cite.201250265 SN - 0009-286X SN - 1522-2640 (eISSN) N1 - ProcessNet-Jahrestagung 2012 und 30. DECHEMA-Jahrestagung der Biotechnologen, 10. – 13. September 2012, Karlsruhe VL - 84 IS - 8 SP - 1296 PB - Wiley-VCH CY - Weinheim ER - TY - GEN A1 - Thiel, A. A1 - Tippkötter, Nils A1 - Muffler, K. A1 - Ruf, F. A1 - Sohling, U. A1 - Ulber, Roland T1 - Optimierung der Wertschöpfungskette bei der Aufarbeitung von Rapsschrot mit Zeolithen T2 - Chemie Ingenieur Technik N2 - Im vom BMELV/FNR geförderten SynRg-Projekt wurde unter anderem Rapsschrot untersucht, um Polyphenole zu isolieren und aufzureinigen. Diese sollen anschließend als Basisbausteine für Polymere dienen und ihnen neuartige Eigenschaften verleihen. Derzeit wird an der Polyphenolextraktion gearbeitet, da bei organischen oder wässrigen Extraktionsprozessen überwiegend Sinapin, ein Cholinester der Sinapinsäure, vorliegt und dieses nicht für die Polymerbildung eingesetzt werden kann. Für die im Fokus stehende Sinapinsäure wird deshalb eine simultane Extraktion und enzymatische oder chemische Hydrolyse von Sinapin zu Sinapinsäure durchgeführt. Durch die Hydrolyse konnte die Sinapinsäureausbeute bereits um den Faktor 6,2 auf 15,8 mg g⁻¹ gegenüber einer reinwässrigen Extraktion gesteigert werden. Für die Aufreinigung des an Sinapinsäure reichen Extrakts erfolgt anschließend ein adsorptiver Aufarbeitungsschritt, bei dem Zeolithe zum Einsatz kommen. Mit diesem Material ist es möglich, die Sinapinsäure quantitativ zu adsorbieren und später mit 70 %igem Ethanol bei 60 °C zu desorbieren. Bei den Adsorbern handelt es sich um b-Zeolithe von der Süd-Chemie AG. Y1 - 2012 U6 - https://doi.org/10.1002/cite.201250028 SN - 0009-286X SN - 1522-2640 (eISSN) N1 - ProcessNet-Jahrestagung 2012 und 30. DECHEMA-Jahrestagung der Biotechnologen, 10. – 13. September 2012, Karlsruhe N1 - Dieses Vorhaben wird aus Mitteln des Bundesministeriums für Ernährung, Landwirtschaft und Verbraucherschutz (BMELV) durch seinen Projektträger der Fachagentur Nachwachsende Rohstoffe e.V. (FNR) unter der Projektnummer22023008 gefördert. VL - 84 IS - 8 SP - 1191 EP - 1192 PB - Wiley-VCH CY - Weinheim ER - TY - GEN A1 - Schumann, C. A1 - Rogin, S. A1 - Schneider, H. A1 - Oster, J. A1 - Tippkötter, Nils A1 - Kampeis, P. T1 - Steuerung von HGMS-Prozessen mittels Durchflusszytometrie T2 - Chemie Ingenieur Technik N2 - Die Hochgradientenmagnetseparation (HGMS) ist eine Methode zur Aufreinigung von biopharmazeutischen Produkten. Mit dieser Methode lässt sich in nur einem Schritt eine Fest/Fest/Flüssig-Trennung erzielen, was zu einer erheblichen Zeit- und Kostenersparnis im Downstreaming führt. Dennoch steht ihr industrieller Einsatz noch aus, was u. a. am Mangel an Analysenmethoden liegt, um die HGMS quantifizierbar zu machen. Gerade in der Pharmaproduktion werden Prozesse gebraucht, die gemäß den einschlägigen Vorschriften (cGMP) validiert und deren verfahrenstechnische Anlagenteile qualifiziert werden können. Die Schwierigkeit ist die Messung der magnetischen Mikrosorbentien in der Suspension, in der auch Zellen oder Zelltrümmer vorliegen. Im Rahmen eines Forschungsprojektes im „Zentralen Innovationsprogramm Mittelstand“ des BMWi wurden verschiedene Analysenmethoden untersucht. Die Durchflusszytometrie ermöglicht eine Charakterisierung von Partikeln und eine simultane quantitative Messung. Durch die multiparametrige Messung kann zwischen Zellen, Zelltrümmern und Magnetpartikeln unterschieden werden. Die At-line-Einbindung des Durchflusszytometers ist durch den Einsatz einer externen Pumpe möglich. Über eine automatisierte Messwertanalyse kann der HGMS-Prozess mittels der Durchflusszytometrie gesteuert werden. Y1 - 2012 U6 - https://doi.org/10.1002/cite.201250125 SN - 0009-286X SN - 1522-2640 (eISSN) N1 - ProcessNet-Jahrestagung 2012 und 30. DECHEMA-Jahrestagung der Biotechnologen, 10. – 13. September 2012, Karlsruhe N1 - Dieses Projekt wurde gefördert durch das Bundesministerium für Wirtschaft und Technologie VL - 84 IS - 8 SP - 1370 PB - Wiley-VCH CY - Weinheim ER - TY - GEN A1 - Sieker, T. A1 - Duwe, A. A1 - Poth, S. A1 - Tippkötter, Nils A1 - Ulber, Roland T1 - Itaconsäureherstellung aus Buchenholz-Hydrolysaten T2 - Chemie Ingenieur Technik N2 - Aus hölzernen Cellulosen und Hemicellulosen können durch enzymatische Hydrolyse fermentierbare Zucker für die Herstellung von Chemikalien und Treibstoffen gewonnen werden. Die bisherige Forschung fokussiert sich oft auf die Nutzung dieser Zucker zur Gewinnung von Ethanol. Daneben muss aber auch die stoffliche Nutzung zur Gewinnung von Grundchemikalien berücksichtigt werden. Eine solche Grundchemikalie ist Itakonsäure. Obwohl die biotechnologische Itaconsäureproduktion bereits eingehend untersucht und etabliert ist, gestaltet sie sich im Rahmen von Bioraffinerien der zweiten Generation als schwierig, da der überwiegend verwendete Produktionsorganismus gegen eine weite Bandbreite von Inhibitoren sensibel ist. Die Herstellung von Itaconsäure aus Buchenholzhydrolysaten wird im Rahmen der deutschen Lignocellulose-Bioraffinerie entwickelt. Die unbehandelten Hydrolysate ermöglichen weder das Wachstum von Aspergillus terreus noch die Bildung von Itaconsäure. Daher werden Möglichkeiten zur Konditionierung des Hydrolysates mit dem Ziel einer Itaconsäureproduktion mit hohen Ausbeuten und Konzentrationen vorgestellt. Y1 - 2012 U6 - https://doi.org/10.1002/cite.201250414 SN - 0009-286X SN - 1522-2640 (eISSN) N1 - ProcessNet-Jahrestagung 2012 und 30. DECHEMA-Jahrestagung der Biotechnologen, 10. – 13. September 2012, Karlsruhe N1 - Die präsentierte Arbeit wird vomBMELV über die FNR gefördert (Förderkennzeichen 22019409). VL - 84 IS - 8 SP - 1300 PB - Wiley-VCH CY - Weinheim ER - TY - JOUR A1 - Tippkötter, Nils A1 - Ulber, Roland T1 - Rezension zu: Encyclopedia of Industrial Biotechnology, Vol. 1–7. By MC Flickinger. JF - Chemie Ingenieur Technik Y1 - 2012 U6 - https://doi.org/10.1002/cite.201290052 SN - 0009-286X SN - 1522-2640 (eISSN) VL - 6 IS - 84 SP - 936 PB - Wiley-VCH CY - Weinheim ER - TY - GEN A1 - Tippkötter, Nils A1 - Staub, C. A1 - Sohling, U. A1 - Ruf, N. A1 - Ulber, Roland T1 - Adsorptive Aufreinigung von Molkeproteinen T2 - Chemie Ingenieur Technik N2 - In der Molkeverarbeitung dominieren Membranfiltrationsverfahren die Prozessführung. Hierbei werden üblicherweise Aufkonzentrierungen der Proteine und deren Trennung von dem Milchzucker Lactose durchgeführt. Der Prozess der adsorptiven Aufreinigung soll als kostengünstige Alternative zu den bisher gebräuchlichen Verfahren dienen. Weiterhin eröffnet sich durch das Verfahren die Möglichkeit, einzelne Proteinfraktionen während der Verarbeitung anzureichern. Als Proteinquellen wurden für die Untersuchungen Modellproteine, Lösungen aus Molkenproteinisolat, Dünnmolke und Molkekonzentrat verwendet. Die Eignung zur Proteinbindung wurden an Tonmaterialien, Silicaten und y-Aluminiumoxiden in Pulverform, in Form von Granulaten sowie Extrudaten als auch sphärischen Partikeln überprüft. Adsorbentien aus Bentonit/Silica und c-Aluminiumoxid können sowohl a-Lactalbumin (aLA) als auch b-Lactoglobulin (bLG) binden, wohingegen Materialien aus Siliciumoxid lediglich ein starkes Adsorptionsverhalten gegenüber bLG zeigen. Mischmaterialien aus Siliciumoxid und a-Aluminiumoxid zeigen dasselbe Verhalten wie Materialien aus Siliciumoxid, weisen jedoch eine geringere Kapazität auf. Die Materialen wurden hinsichtlich ihres Einsatzes in chromatographischen Verfahren und Batch-Prozessen untersucht und ein Prozessentwurf für einen zweistufigen Batch-Prozess im Rührkessel erarbeitet. KW - Molkeproteine KW - Adsorption Y1 - 2012 U6 - https://doi.org/10.1002/cite.201250395 SN - 0009-286X SN - 1522-2640 (eISSN) N1 - ProcessNet-Jahrestagung 2012 und 30. DECHEMA-Jahrestagung der Biotechnologen, 10. – 13. September 2012, Karlsruhe VL - 84 IS - 8 SP - 1285 PB - Wiley-VCH CY - Weinheim ER - TY - GEN A1 - Thiel, A. A1 - Tippkötter, Nils A1 - Suck, K. A1 - Sohling, U. A1 - Ruf, F. A1 - Ulber, Roland T1 - Simulation und Experiment bei der Aufarbeitung von Polyphenolen durch neue Silicatmaterialien T2 - Chemie Ingenieur Technik N2 - Nachwachsende Rohstoffe stellen eine reichhaltige Quelle für die Gewinnung von wirtschaftlich interessanten Biomolekülen dar. Die Gruppe der Polyphenole ist dabei für mehrere Industriezweige bedeutend. Ihre antioxidativen Eigenschaften sind z. B. für die Pharmaindustrie interessant. Im derzeit bearbeiteten Projekt sollen Polyphenole aus Pflanzenbestandteilen isoliert und aufgereinigt werden, um sie dann als Komponenten für eine Vernetzung von Polymeren auf der Basis von Fettsäuren einzusetzen. Bisher sind im Wesentlichen Prozesse zur Entfernung von Polyphenolen aus Getränken wie Bier und Wein bekannt. Eine Wiedergewinnung der Polyphenole war in diesen Anwendungen bisher nicht relevant. Die Gewinnung bzw. Abtrennung der Polyphenole erfolgt u. a. durch kommerziell erhältliche Adsorbentien wie PVPP, Adsorberharze XAD16 (Rhöm & Haas) oder SP70 (Sepabeads), deren Partikelgrößen im Bereichvon 0,1 ± 0,8 mm und spezifischen Oberflächen von 700 ± 900 m 2 /g liegen. Als Alternative zu diesen Adsorbern sollen neue Materialien auf Basis von anorganischen Trennmedien, wie z. B. natürlichen Tonmineralien, für die Polyphenolabtrennung verwendet werden. Derzeit wird durch Abgleich von Experiment und Simulation ein Materialscreening durchgeführt. Durch den Einsatz molekulardynamischer Bindungssimulationen wird die Adsorbersuche beschleunigt und Vorhersagen zu Modifikationen bei der Herstellung der neuen Adsorbentien ermöglicht. Y1 - 2010 U6 - https://doi.org/10.1002/cite.201050104 SN - 0009-286X SN - 1522-2640 (eISSN) N1 - ProcessNet-Jahrestagung 2010 und 28. DECHEMA-Jahrestagung der Biotechnologen, 21. - 23. September 2010, Eurogress Aachen VL - 82 IS - 9 SP - 1589 PB - Wiley-VCH CY - Weinheim ER - TY - GEN A1 - Tippkötter, Nils A1 - Wulfhorst, H. A1 - Mogue, N. A1 - Möhring, S. A1 - Roth, J. A1 - Ulber, Roland T1 - Spektrometrische Messung und Modellierung der enzymatischen Hydrolyse von Biomasse nach Organosolv- und Liquid Hot Water-Aufschlüssen (LHW) T2 - Chemie Ingenieur Technik N2 - In diesem Beitrag wird die NIR- und MIR-Spektrometrie in Kombination mit multivariaten Kalibrationsmodellen zur Analyse von Monosacchariden und Cellulose aus Biomasse etabliert. Spektrengemischter Standardlösungen mit definierten Glucose- und Xylosekonzentrationen in Wasser werden im NIR-(Lambda 750, Perkin Elmer, USA) und MIR-Bereich (Spektrum 100, PerkinElmer) in Gegenwart von entweder Carboxymethylcellulose oder Grasfasern aufgenommen. Darauf basierend werden Kalibrationsmodelle (Unscrambler®, CAMO-Software AS, Norwegen) entwickelt und zur Vorhersage der Zuckerkonzentration in den Hydrolyseproben und der Celluloseanteile angewendet. Darüber hinaus wird die Partikelgröße der Rohstoffe bestimmt. Die Messergebnisse bilden die experimentelle Basis für die numerische Modellierung der Reaktionskinetik der enzymatischen Hydrolyse von Lignocellulose. Das Modell kombiniert die Bilanzierung der Partikelgrößenverteilungen mit der Multienzymkinetik. Dabei werden neben der Partikelgrößenverteilung und der Substratkonzentration die Zusammensetzung der Rohstoffe nach Vorbehandlung sowie die Produktinhibierung und mehrere enzymatische Aktivitäten berücksichtigt. Das Modell ermöglicht es, die Partikelgrößenverteilungen und die Konzentrationen der Substrate und Produkte während der Hydrolyse vorherzusagen und die kinetischen Parameter im Batch- sowie im Fed-Batch-Reaktor zu bestimmen. Y1 - 2014 U6 - https://doi.org/10.1002/cite.201450269 SN - 0009-286X SN - 1522-2640 (eISSN) N1 - ProcessNet-Jahrestagung 2014 und 31. DECHEMA-Jahrestagung der Biotechnologen, 30. September - 2. Oktober 2014, Eurogress Aachen VL - 86 IS - 9 SP - 1584 PB - Wiley-VCH CY - Weinheim ER - TY - GEN A1 - Engel, M. A1 - Tippkötter, Nils T1 - Einfluss eines Phenazin-Mediators und elektrischen Potenzials auf die Aceton-Butanol-Ethanol-Fermentation T2 - Chemie Ingenieur Technik N2 - In den letzten Jahren haben nachhaltige, biotechnologische Prozesse zunehmend an Bedeutung gewonnen. Die Aceton-Butanol-Ethanol-Fermentation (ABE-Fermentation) mit dem anaeroben Bakterium Clostridium acetobutylicum zur Gewinnung von Biobutanol könnte in diesem Zusammenhang eine Möglichkeit der nachhaltigen Kraftstoffproduktion darstellen. In dieser Arbeit wird der Einfluss zusätzlich verfügbarer Elektronen durch den Einsatz des Phenazin-Farbstoffs Neutralrot als Redoxmediator sowie das Anlegen eines elektrischen Potenzials während der ABE-Fermentation untersucht. Es wird gezeigt, dass das Neutralrot keinen Einfluss auf die Leerlaufspannung von ca. 500 mV vs. Ag/AgCl während der Fermentation hat. Der Mediator bewirkt allerdings eine frühere Butanolbildung sowie höhere Butanolkonzentrationen. Wird zudem die Mediatorkonzentration von 125 mM auf 250 mM angehoben, wird dabei auch die maximale Butanolkonzentration um 36 % ± 1,8 % innerhalb von28 Stunden gesteigert. Y1 - 2016 U6 - https://doi.org/10.1002/cite.201650105 SN - 0009-286X SN - 1522-2640 (eISSN) N1 - ProcessNet-Jahrestagung 2016 und 32. DECHEMA-Jahrestagung der Biotechnologen 2016, 12. - 15. September 2016, Eurogress Aachen VL - 88 IS - 9 SP - 1254 PB - Wiley-VCH CY - Weinheim ER - TY - GEN A1 - Sieker, T. A1 - Tippkötter, Nils A1 - Ulber, Roland T1 - Simultane Vorbehandlung, Hydrolyse und Fermentation bei der Nutzung von grüner Biomasse zur Produktion von Bioethanol T2 - Chemie Ingenieur Technik N2 - Gräser sind in der Lage, einen großen Teil der für eine biobasierte Wirtschaft benötigten Biomasse zur Verfügung zu stellen. Wie bei anderen lignocellulosehaltigen nachwachsenden Rohstoffen erfordert die Verwertung der im Gras enthaltenen Polysaccharide einen mehrstufigen Prozess aus Vorbehandlung, Hydrolyse und Fermentation. In Gräsern ist die Hemicellulose mitP henolcarbonsäuren wie Ferula- und p-Coumarsäure verestert, die die enzymatische Hydrolyse der Cellulose und Hemicellulose ebenso effektiv behindern wie Lignin. Anders als bei holzigen Rohstoffen ermöglicht dieser Aufbau aber eine enzymatische Vorbehandlung, mit der die Phenolcarbonsäuren abgespalten werden können. Da die bei der Vorbehandlung eingesetzten Enzyme in ihrer natürlichen Funktion synergistisch mit cellulytischen Enzymen zusammenarbeiten, besitzen sie ähnliche Optima wie die für die Hydrolyse der Polysaccharide eingesetzten Cellulasen und Hemicellulasen. Diese Eigenschaft ermöglicht die Integration von Vorbehandlung und Hydrolyse in einem einzigen Verfahrensschritt. Durch die Einführung der enzymatischen Vorbehandlung konnte das in der Literatur bekannte SSF-Verfahren für die Herstellung von Ethanol aus Gräsern um die Vorbehandlungsstufe erweitert werden. Das so realisierte simultaneous pretreatment, saccharification and fermentation (SPSF)-Verfahren stellt eine vollständige Integration der drei für die Nutzung von Lignocellulose nötigen Verfahrensschritte in der grünen Bioraffinerie dar. Y1 - 2010 U6 - https://doi.org/10.1002/cite.201050319 SN - 0009-286X N1 - ProcessNet-Jahrestagung 2010 und 28. DECHEMA-Jahrestagung der Biotechnologen, 21. - 23. September 2010, Eurogress Aachen VL - 82 IS - 9 SP - 1601 PB - Wiley-VCH CY - Weinheim ER - TY - GEN A1 - Sieker, T. A1 - Tippkötter, Nils A1 - Ulber, Roland A1 - Bart, H.-J. A1 - Heinzle, E. T1 - Nutzung von Silage zur fermentativen Produktion von Grund-und Feinchemikalien T2 - Chemie Ingenieur Technik N2 - Grasschnitt hat in Deutschland ein beträchtliches Potenzial als nachwachsender Rohstoff. Da frischer Grasschnitt nur in den Sommermonaten zur Verfügung steht und Gras bei der Lagerung verrottet, wird er unter anderem durch Silierung konserviert. Während der Silierung wird ein Teil der wasserlöslichen Kohlenhydrate unter anaeroben Bedingungen zu Milchsäure fermentiert. Die Kombination aus Luftabschluss und Ansäuerung bewirkt die Konservierung der Silage. Silage als weit verbreitetes landwirtschaftliches Erzeugnis ist somit ein potentieller, in großen Mengen verfügbarer Lieferant für eine Vielzahl von Substraten für mikrobielle Fermentationen. Diese können entweder durch die Hydrolyse der in den Pflanzen enthaltenen Cellulosen und Hemicellulosen oder durch die Verwendung eines Silagepresssaftes nutzbar gemacht werden. Die zu entwickelnden Prozesse sollen die verbleibenden Kohlenhydrate, inklusive der Cellulose und Hemicellulose, sowie die Milchsäure nutzen. Die in der Silage enthaltenen Zucker sollen zu Ethanol, Itakonsäure und Bernsteinsäure und die Milchsäure zu 1,2-Propandiol umgesetzt werden. Anfallende Reststoffe wie Hydrolyserückstände, Presskuchen und Fermentationsrückstände sollen bei allen zu etablierenden Prozessen entweder als Viehfutter verwendet oder der Biogasproduktion zugeführt werden können, wodurch eine vollständige stoffliche und energetische Nutzung der Silage erreicht wird. Y1 - 2009 U6 - https://doi.org/10.1002/cite.200950271 SN - 0009-286X SN - 1522-2640 (eISSN) N1 - ProcessNet‐Jahrestagung 2009 und 27. DECHEMA-Jahrestagung der Biotechnologen, 8.- 10. September 2009, Mannheim N1 - Das Projekt wird durch die Fachagenur für Nachwachsende Rohstoffe gefördert ((22025407)(07NR254)) VL - 81 IS - 8 SP - 1207 PB - Wiley-VCH CY - Weinheim ER - TY - GEN A1 - Capitain, C. A1 - Hering, T. A1 - Tippkötter, Nils T1 - Enzymatische Polymerisation von Ligninmodellkomponenten und Organosolv-Lignin mit aromatischen Aminosäuren T2 - Chemie Ingenieur Technik N2 - Die stoffliche Nutzung von Lignin aus Bioraffinerien ist ein wichtiger Bestandteil für den Wertschöpfungsprozess von nachwachsenden, pflanzlichen Rohstoffen. Lignin zählt zu den wenigen erneuerbaren Quellen für phenolische Bestandteile, wird aber derzeit meist nur thermisch verwertet. Ziel dieses Forschungsvorhabens ist die Funktionalisierung von Lignin zur Verbesserung der Adhäsionseigenschaften. Als funktionelle Gruppe wird die aromatische Aminosäure L-DOPA verwendet, die charakteristisch für die Adhäsionskraft von Muscheln ist. Lignin ist ein geeignetes Stützgerüst, da es ein Polymer ist, das durch enzymkatalysierte Polymerisation gebildet wird. Essenziell für die Entwicklung ist ein besseres Verständnis über die Bildung von Lignin-Polymeren und deren verschiedene Eigenschaften. Um die Einflussfaktoren auf Kettenlänge und Polymerisationseffizienz zu untersuchen, werden zurzeit sowohl Ligninmodellkomponenten (LMK) als auch gelöstes Organosolv-Lignin verwendet. Laufende Untersuchungen werden zeigen, ob sich die enzymatische Polymerisationsreaktion auf ein gelöstes Ligninpolymer aus einem Organosolv-Aufschluss übertragen lässt. Y1 - 2016 U6 - https://doi.org/10.1002/cite.201650374 SN - 0009-286X SN - 1522-2640 (eISSN) N1 - ProcessNet-Jahrestagung 2016 und 32. DECHEMA-Jahrestagung der Biotechnologen 2016, 12. - 15. September 2016, Eurogress Aachen VL - 88 IS - 9 SP - 1236 PB - Wiley-VCH CY - Weinheim ER - TY - GEN A1 - Poth, S. A1 - Monzon, M. A1 - Tippkötter, Nils A1 - Ulber, Roland T1 - Fermentation von Hydrolysaten aus Lignocellulose T2 - Chemie Ingenieur Technik N2 - Die ökonomische Abhängigkeit von fossilen Brennstoffen und der klimatische Wandel durch die Nutzung dieser haben zu einer intensiven Suche nach erneuerbaren Rohstoffen für die Produktion von Chemikalien und Treibstoffen geführt. Ein viel versprechender Rohstoff in diesem Zusammenhang sind Zucker, die mittels enzymatischer Hydrolyse aus Lignocellulose gewonnen werden können. Die Fermentation erfolgt mit Cellulose- bzw. Hemicellulose-Fraktionen, welche durch thermo-chemische Vorbehandlung von Holz gewonnen und anschließend enzymatisch hydrolysiert werden. Die in den Hydrolysaten enthaltenen Zuckermonomere dienen als Kohlenstoffquelle für die Produktion von Ethanol. Da sowohl Glucose als auch Xylose in den unterschiedlichen Fraktionen enthalten sind, wird zur Umsetzung dieser eine Co-Fermentation zweier Hefen durchgeführt. Im Rahmen der Optimierung dieser Fermentationen werden neben der Ergänzung der Hydrolysate durch notwendige Salze auch Verfahrenweisen wie Fed-Batch-Fermentationen untersucht. Ein weiterer interessanter Ansatz, welcher in diesem Rahmen geprüft wird, ist die enzymatische Hydrolyse der Lignocellulose-Fraktionen und die simultane Fermentation der dabei entstehenden Zucker in einem Schritt. Des Weiteren wurde die Eignung der Hydrolysate für die Biomasseproduktion anderer Mikroorganismen wie Escherichia coli getestet. Y1 - 2009 U6 - https://doi.org/10.1002/cite.200950243 SN - 0009-286X SN - 1522-2640 (eISSN) N1 - ProcessNet‐Jahrestagung 2009 und 27. DECHEMA-Jahrestagung der Biotechnologen, 8.- 10. September 2009, Mannheim N1 - Das hier vorgestellte Vorhaben wird durch die Fachagentur für Nachwachsende Rohstoffe(FNR) gefördert: „Verbundvorhaben: Pilotprojekt Lignocellulose-Bioraffinerie, Teilvorhaben 1: Extraktverarbeitung, Enzymtechnologie, verfahrenstechnische Untersuchungen, Ökobilanzierung, Wirtschaftlichkeitsberechnungen“ (Förderkennzeichen: FNR 22027405). VL - 81 IS - 8 SP - 1220 PB - Wiley-VCH CY - Weinheim ER - TY - GEN A1 - Sieker, T. A1 - Tippkötter, Nils A1 - Muffler, K. A1 - Ulber, Roland T1 - Herstellung von Ethanol, Phenolsäuren, organischen Säuren und Biogas durch vollständige Nutzung von Grassilage in einer Bioraffinerie T2 - Chemie Ingenieur Technik N2 - Gräser sind in der Lage, einen großen Teil der für eine biobasierte Wirtschaft benötigten Biomasse zur Verfügung zustellen. Um eine ganzjährige Nutzung des Grases zu gewährleisten, muss eine stabile Lagerung des Grases erreicht werden, was z. B. durch Silieren möglich ist. Die konservierende Wirkung der Silierung beruht auf der Bildung organischer Säuren. Um diese zu gewinnen, wird die Silage gepresst, die organischen Säuren über Flüssig/Flüssig-Extraktion aus dem Presssaft abgetrenntund mittels chromatographischer Methoden weiter aufgereinigt. Im präsentierten Konzept werden die im Presskuchen enthaltenen Lignocellulosen hydrolysiert und die erhaltenen Monosaccharide zu Ethanol fermentiert. Die Phenolsäuren, die in Gräsern die Rolle des Lignins übernehmen, können simultan mit der Hydrolyse der Polysaccharide enzymatisch abgetrennt und als Nebenprodukt gewonnen werden. Die nach der Abtrennung des Ethanols verbleibenden Fermentationsreststoffe werden für die Herstellung von Biogas verwendet. Y1 - 2012 U6 - https://doi.org/10.1002/cite.201250415 SN - 0009-286X SN - 1522-2640 (eISSN) N1 - ProcessNet-Jahrestagung 2012 und 30. DECHEMA-Jahrestagung der Biotechnologen, 10. – 13. September 2012, Karlsruhe N1 - Die präsentierte Arbeit wird vom BMELV über die FNR gefördert (Förder-kennzeichen 22025407). VL - 84 IS - 8 SP - 1297 PB - Wiley-VCH CY - Weinheim ER - TY - GEN A1 - Tippkötter, Nils A1 - Pasteur, A. A1 - Meyer, C. A1 - Kampeis, P. A1 - Diller, R. A1 - Ulber, Roland T1 - Aufreinigung von Cephalosporin C durch poröse, selektiv-beschichtete Magnetpartikel T2 - Chemie Ingenieur Technik N2 - Die selektive Isolierung von Cephalosporin C (CPC) aus komplexen Fermentationssuspensionen unter Einsatz magnetischer Separation ist das Ziel dieser Arbeit. Das Verfahren wird im frühen Stadium der Aufarbeitung genutzt, um CPC zu stabilisieren und somit die Produktausbeute zu erhöhen. Als Adsorbersysteme für CPC wurden neben einem projektinternen magnetischen Material ND 10322, dessen Oberflächenladungen spezifisch für die Bindung des Zielmoleküls synthetisiert wurden, verschiedene kommerzielle Partikelsysteme verglichen. Es konnten massenspezifische Maximalbeladungen von 51 mg g⁻¹ erreicht werden. Weiterhin wurde die Stabilität von CPC untersucht. Unter optimalen Adsorptionsbedingungen kann CPC stabilisiert werden, so dass die Geschwindigkeitskonstante der Degradation des b-Lactam-Rings unter diesen Bedingungen unter 0,005 h⁻¹ liegt. Untersuchungen zur Wiederverwertbarkeit der neuen Adsorbers zeigten eine irreversible Bindung geringer CPC-Mengen nach dem ersten Einsatz. Nach zwölf Zyklen tritt eine irreversible Bindung von CPC ein, was zu einer signifikanten Reduktion der Adsorptionsfähigkeit führt. Die Anhäufung des CPC auf dem Adsorber konnte durch IR-Untersuchungen auf die Bildung einer Peptidbindung zwischen Carboxylgruppen des CPC und Aminogruppe der Adsorberoberfläche zurückgeführt werden. Y1 - 2012 U6 - https://doi.org/10.1002/cite.201250391 SN - 0009-286X SN - 1522-2640 (eISSN) N1 - ProcessNet-Jahrestagung 2012 und 30. DECHEMA-Jahrestagung der Biotechnologen, 10. – 13. September 2012, Karlsruhe VL - 84 IS - 8 SP - 1369 EP - 1370 PB - Wiley-VCH CY - Weinheim ER - TY - GEN A1 - Engel, M. A1 - Bayer, H. A1 - Ulber, Roland A1 - Tippkötter, Nils T1 - Kommt es in Elektrofermentationen mit Clostridium acetobutylicum zu einer Eisenlimitierung? T2 - Chemie Ingenieur Technik N2 - Das strikt anaerobe Bakterium Clostridium acetobutylicum bildet die Lösemittel Aceton, Butanol und Ethanol (ABE-Fermentation). Im Fall einer Eisenlimitierung kommt es zusätzlich zu einer Riboflavinsekretion (RF), was durch die gelbe Färbung des Kulturüberstands erkennbar ist. In dieser Arbeit wurde beobachtet, dass während Elektrofermentationen mit C. acetobutylicum bei –600 mV eine gelbe Färbung auftritt. Es wurde deshalb untersucht, ob eine Eisenlimitierung im bio-elektrochemischen System (BES) vorliegt. Hierzu wurden die Flavinspezien bei Kultivierungen in Medien mit einer Eisenlimitierung bzw. mit ausreichend Eisen in Serumflaschen sowie im BES mit und ohne angelegtem Potenzial verglichen. In den Serumflaschenversuchen wurden RF und Flavinadenindinukleotid (FAD)-Konzentrationen von ‡ 20 mg L⁻¹ sowie Flavinmononukleotid (FMN)-Konzentrationen von ca. 5 mg L⁻¹ detektiert. Bei ausreichender Eisenverfügbarkeit hingegen wurden in den Serumflaschen fast keine Flavine sekretiert. Im BES bei –600 mV hingegen wurde auch in diesen Kulturüberständen FMN und FAD (1–5 mg L⁻¹ ),jedoch kein RF gemessen. Diese Ergebnisse zeigen, dass die Flavinbildung im BES mit angelegtem Potenzial nicht mit der Flavinbildung unter Eisenlimitierung in Serumflaschen korreliert. Andere Faktoren für eine mögliche Flavinbildung werden aktuell näher betrachtet. Y1 - 2018 U6 - https://doi.org/10.1002/cite.201855047 SN - 0009-286X SN - 1522-2640 (eISSN) N1 - ProcessNet-Jahrestagung und 33. DECHEMA-Jahrestagung der Biotechnologen 2018, 10. - 13. September 2018, Eurogress Aachen VL - 90 IS - 9 SP - 1154 PB - Wiley-VCH CY - Weinheim ER - TY - GEN A1 - Duwe, A. A1 - Schlegel, C. A1 - Tippkötter, Nils A1 - Ulber, Roland T1 - Sequentielle Extraktion von Cellulose zur effizienten Nutzung der Stoffströme in der Holzbioraffinerie T2 - Chemie Ingenieur Technik N2 - In der Reihe der nachwachsenden Rohstoffe besitzt Holz als erneuerbare und umweltfreundliche Ressource ein großes Potenzial. Über 11 Mio. ha Holz, das laut der Fachagentur für nachwachsende Rohstoffe (FNR) auch für industrielle Zwecke genutzt werden kann, wuchsen im Jahr 2013 allein auf bundesdeutscher Fläche. 56,8 Mio. m³ jährlicher Holzeinschlag in den letzten zehn Jahren wurde zu knapp der Hälfte stofflich und der Rest energetisch verwertet. Im Rahmen dieser Arbeit konnte auf der Basis vom Holz der Buche, die nach Fichte und Kiefer die dritthäufigste Baumart in Deutschland ist und 15% der deutschen Waldfläche ausmacht, die Fraktionierung der polymeren Hauptbestandteile mit niedrigem energetischen Einsatz erreicht werden. Hierbei werden in einem nachgeschalteten Extraktionsprozess die beiden Komponenten Hemicellulose und Lignin in flüssiger Form von der finalen festen Cellulosefraktion abgetrennt. Die Extraktion der Hemicellulose erfolgt durch eine Liquid Hot Water (LHW)-Behandlung. Untersucht wird der katalytische Zusatz anorganischer Säuren wie H₃PO₄ und H₂SO₄. Im Hinblick auf die weitere Verwertung von Lignin zu aromatischen Synthesebausteinen kommt die Organosolv-Extraktion mit einem Ethanol/Wasser-Gemisch zum Einsatz. Von Vorteil ist die weitere Verwendung beider Stoffströme ohne Fällungsschritt und nachteiliger Verdünnung der Hemicellulose. Y1 - 2014 U6 - https://doi.org/10.1002/cite.201450308 SN - 0009-286X SN - 1522-2640 (eISSN) N1 - ProcessNet-Jahrestagung 2014 und 31. DECHEMA-Jahrestagung der Biotechnologen, 30. September - 2. Oktober 2014, Eurogress Aachen VL - 86 IS - 9 SP - 1400 PB - Wiley-VCH CY - Weinheim ER - TY - GEN A1 - Tippkötter, Nils A1 - Maurer, S. A1 - Pasteur, A. A1 - Kampeis, P. A1 - Ulber, Roland T1 - Hochgradient-Magnetseparation von Fermentationsprodukten–FEM Simulation der Filtermatrix T2 - Chemie Ingenieur Technik N2 - Durch den Einsatz magnetisierbarer Partikel lassen sich Stoffwechselprodukte direkt und selektiv aus feststoffreichen Fermentationssuspensionen abtrennen. Im Gegensatz zu klassischen Adsorbermaterialien können magnetisierbare Partikel mit sehr geringen Durchmessern verwendet werden. Zur deren Abtrennung ist jedoch ein hoher Magnetfeldgradient notwendig. Dieser wird in der Regel durch in der Trennkammer bzw. dem Magnetfeld eingebrachte magnetisierbare Drähte realisiert. Bei der Auslegung der Drahtgitter ist ein Kompromiss zwischen Abtrennrate und Durchlässigkeit nötig. Die Ausrichtung der Drähte in Relation zum Magnetfeld, deren Abstand sowie die geometrische Anordnung können hierbei variiert werden. Zum Verständnis der Einflüsse auf das sich ausbildende Magnetfeld und die Fluiddynamik wurden Simulationen mit der Finite-Elemente-Methode durchgeführt und experimentell überprüft. Hierfür wurden die Drähte unter Variation von Anzahl, Richtung und Anordnung in den Hochgradient-Magnetseparator eingebracht. Erste Verifizierungen der Simulationen zeigen, dass die in Magnetfeldrichtung ausgerichteten Drähte (x-Achse) über die geringste Partikelrückhaltefähigkeit verfügen. Die Drähte der y- und z-Achse halten den größten Anteil der Magnetpartikel zurück, wobei die Drähte in y-Richtung den höchsten Feldgradienten ausbilden. Des Weiteren konnte gezeigt werden, dass eine rhomboedrische Drahtanordnung der kubischen vorzuziehen ist. Y1 - 2010 U6 - https://doi.org/10.1002/cite.201050217 SN - 0009-286X SN - 1522-2640 (eISSN) N1 - ProcessNet-Jahrestagung 2010 und 28. DECHEMA-Jahrestagung der Biotechnologen, 21. - 23. September 2010, Eurogress Aachen VL - 82 IS - 9 SP - 1361 PB - Wiley-VCH CY - Weinheim ER - TY - GEN A1 - Möhring, S. A1 - Wulfhorst, H. A1 - Capitain, C. A1 - Roth, J. A1 - Tippkötter, Nils T1 - Fractioning of lignocellulosic biomass: Scale-down and automation of thermal pretreatment for parameter optimization T2 - Chemie Ingenieur Technik N2 - In order to efficiently convert lignocellulose, it is often necessary to conduct a pretreatment. The biomass considered in this study typically comprises of agricultural and horticultural residues, as well as beechwood. A very environmentally friendly method, namely, fungal pretreatment using white-rot fungi, leads to an enhanced enzymatic hydrolysis. In contrast to other processes presented, the energy input is extremely low. However, the fungal growth on the lignocellulosic substrates takes several weeks at least in order to be effective. Thus, the reduction of chemicals and energy for thermal processing is a target of our current research. Liquid hot water (LHW) and solvent-based pretreatment (OrganoSolv) require more complex equipment, as they depend on high temperatures (160 – 180 °C) and enhanced pressure (up to 20 bar). However, they prove to be promising processes in regard to the fractioning of lignocellulose. For optimal lignin recovery the parameters differ from those established in cellulose extraction. A novel screening system scaled down to a reaction volume of 100 mL has been developed and successfully tested for this purpose. Y1 - 2016 U6 - https://doi.org/10.1002/cite.201650288 SN - 0009-286X SN - 1522-2640 (eISSN) N1 - ProcessNet-Jahrestagung und 32. DECHEMA-Jahrestagung der Biotechnologen 2016, 12. - 15. September 2016, Eurogress Aachen VL - 88 IS - 9 SP - 1229 PB - Wiley-VCH CY - Weinheim ER - TY - GEN A1 - Capitain, C. C. A1 - Lukeba, L. A1 - Ulber, Roland A1 - Tippkötter, Nils T1 - Biomimetische Klebstoffe aus Organosolv-Lignin T2 - Chemie Ingenieur Technik N2 - Aufgrund von EU-Regularien und Umweltinitiativen wächst der Markt für nachhaltige und abbaubare Klebstoffe stetig. Organosolv (OS)-Lignin ist ein kommerziell wenig ertragreicher Nebenstrom der Lignocellulose-Bioraffinerie. Durch das "Nachahmen" der Adhäsionseigenschaften mit strukturverwandten Muschel-Aminosäuren soll OS-Lignin in einen starkes, vollständig biobasiertes Adhäsiv umgewandelt werden. Funktionsweisend für die Adhäsion des Muschelklebstoffes ist die Catecholgruppe der Aminosäure L-DOPA. Die laccase-katalysierte Polymerisationsreaktion von Lignin und L-DOPA ist schwierig zu kontrollieren, da L-DOPA eine Ringschlussreaktion eingeht. Stattdessen wurde eine zweistufige Reaktion mit einem Diamin als Ankermolekül etabliert. Die Catecholgruppe, die im zweiten Schritt enzymatisch an das Lignin-Amin gebunden wird, kann durch Komplexbildung mit Fe(III)-Ionen sowohl zur Adhäsion als auch zur Kohäsion des Klebstoffes beitragen. Der Lignin-Catechol-Klebstoff ist frei von petrochemischen Chemikalien und biologisch abbaubar. In ersten Stirnzugversuchen konnte eine Haftkraft von 0,3 MPa erreicht werden. Y1 - 2018 U6 - https://doi.org/10.1002/cite.201855076 SN - 0009-286X SN - 1522-2640 (eISSN) N1 - ProcessNet-Jahrestagung und 33. DECHEMA-Jahrestagung der Biotechnologen 2018, 10. - 13. September 2018, Eurogress Aachen VL - 90 IS - 9 SP - 1167 PB - Wiley-VCH CY - Weinheim ER - TY - GEN A1 - Ross-Jones, J. A1 - Teumer, T. A1 - Capitain, C. A1 - Tippkötter, Nils A1 - Krause, M. J. A1 - Methner, F.-J. A1 - Rädle, M. T1 - Analytical methods for in-line characterization of beer haze T2 - Trends in Brewing N2 - In most beers, producers strive to minimize haze to maximize visual appeal. To detect the formation of particulates, a measurement system for sub-micron particles is required. Beer haze is naturally occurring, composed of protein or polyphenol particles; in their early stage of growth their size is smaller than 2 µm. Microscopy analysis is time and resource intensive; alternatively, backscattering is an inexpensive option for detecting particle sizes of interest. Y1 - 2018 N1 - Trends in Brewing, April 8 –12, 2018, Ghent, Belgium ER - TY - GEN A1 - Tippkötter, Nils A1 - Neitmann, E. A1 - Sohling, U. A1 - Ruf, F. A1 - Ulber, Roland T1 - Anaerobe Produktion von ABE-Lösungsmitteln aus an Bleicherde adsorbiertem Öl T2 - Chemie Ingenieur Technik N2 - Mit Palmöl beladene Bleicherde wurde auf die Anwendbarkeit als Rohstoff zur Bildung von Aceton, Ethanol und Butanol (ABE) untersucht. Nach der Abtrennung des entfärbten bzw. gebleichten Öls bestehen 20–40 % (w/w) des Bleicherderückstands aus adsorbiertem Öl. Somit stellt das Mineral einen wertvollen Rohstoff dar. Zur Produktion der Lösungsmittel wurde das gebundene Öl hydrolysiert. Das freigesetzte Glycerin diente als Substrat einer nachfolgenden anaeroben Fermentation zu den ABE-Lösungsmitteln. Die Fermentationen wurden mit verschiedenen Clostridien-Stämmen durchgeführt, von denen einige lipolytische Aktivität aufweisen. Der Ölgehalt der Bleicherde betrug 28 % der Adsorbermasse. Für die Hydrolyse wurden drei Ansätze untersucht: 1. die direkte Fermentation des Adsorbers mit lipolytisch aktiven Clostridien, 2. der Einsatz von Lipasen und die Fermentation des resultierenden Überstands und 3. die Kofermentation mit einer lipolytisch aktiven Hefe. Jeder der drei Ansätze führte zu einerHydrolyse des Öls und Wachstum der Mikroorganismen. Der Einsatz von Lipasen resultierte in einer vollständigen und der schnellsten Hydrolyse des Öls. Eine Glycerinkonzentration von 13,4 g/L konnte erreicht werden. Die anaerobe Fermentation der verschiedenen Clostridien auf Minimalmedien verlief erfolgreich. Der Vergleich der Fermentationen der Bleicherdehydrolysate zeigte, dass das Hydrolysat wachstumsinhibierende Substanzen enthält. Unter diesen Bedingungen konnte eine Ausbeute von Y P/S = 0,11 erzielt werden. Der Einsatz eines Ionenaustauschers zur Reinigung des Hydrolysats vor der Fermentation resultierte in einer Verbesserung des Wachstums Y1 - 2009 U6 - https://doi.org/10.1002/cite.200950075 SN - 0009-286X SN - 1522-2640 (eISSN) N1 - ProcessNet‐Jahrestagung 2009 und 27. DECHEMA-Jahrestagung der Biotechnologen, 8.- 10. September 2009, Mannheim VL - 81 IS - 8 SP - 1217 EP - 1218 PB - Wiley-VCH CY - Weinheim ER - TY - CHAP A1 - Engel, Mareike A1 - Thieringer, Julia A1 - Tippkötter, Nils T1 - Linking bioprocess engineering and electrochemistry for sustainable biofuel production T2 - Young Researchers Symposium, YRS 2016. Proceedings N2 - Electromicrobial engineering is an emerging, highly interdisciplinary research area linking bioprocesses with electrochemistry. In this work, microbial electrosynthesis (MES) of biobutanol is carried out during acetone-butanol-ethanol (ABE) fermentations with Clostridium acetobutylicum. A constant electric potential of −600mV (vs. Ag/AgCl) with simultaneous addition of the soluble redox mediator neutral red is used in order to study the electron transfer between the working electrode and the bacterial cells. The results show an earlier initiation of solvent production for all fermentations with applied potential compared to the conventional ABE fermentation. The f inal butanol concentration can be more than doubled by the application of a negative potential combined with addition of neutral red. Moreover a higher biofilm formation on the working electrode compared to control cultivations has been observed. In contrast to previous studies, our results also indicate that direct electron transfer (DET) might be possible with C. acetobutylicum. The presented results make microbial butanol production economically attractive and therefore support the development of sustainable production processes in the chemical industry aspired by the “Centre for resource-efficient chemistry and raw material change” as well as the the project “NanoKat” working on nanostructured catalysts in Kaiserslautern. Y1 - 2016 N1 - Young Researchers Symposium, YRS 2016, 14th - 15th April 2016, Fraunhofer-Zentrum Kaiserslautern SP - 49 EP - 53 PB - Fraunhofer Verlag CY - Karlsruhe ER - TY - GEN A1 - Tippkötter, Nils A1 - Pasteur, A. A1 - Ulber, Roland T1 - Magnetisch abtrennbare Gold-Nanopartikel zur katalytischen Zuckeroxidation T2 - Chemie Ingenieur Technik N2 - Glucose ist ein primäres Zwischenprodukt der Verarbeitung nachwachsender Rohstoffe, wie z. B. Cellulose. Die wertsteigernde Weiterverarbeitung des Monosaccharids erfolgt häufig in Form vonFermentationsprozessen, jedoch kann der Rohstoff auch für zahlreiche chemische Verarbeitungsstufen genutzt werden. Ein großtechnisch relevanter Prozess ist die Herstellung von Gluconsäure (GS), die u. a. als Nahrungsmittelzusatz (E 574) eingesetzt wird. Die Darstellung der Säure erfolgt durch Oxidation von Glucose mit magnetisierbarem Gold-Nano-Katalysator. Die Rückgewinnung des Katalysators aus der Reaktionslösung wurde unter Einwirkung eines Magnetfeldgradienten verwirklicht. Die Synthese der magnetischen Goldkatalysatoren (sowohl Trägerpartikel als auch Gold-Nanopartikel) wurde durch nass-chemische Fällungsreaktionen durchgeführt. Die Charakteristiken der neuen Materialen konnte durch Messungen des PCD-Potenzials, Laserbeugung und REM/EDX untersucht werden. So wurden u. a. Partikeldurchmesser von 25 lm und ein Goldgehaltvon 1,03 % ermittelt. Weiterhin wurden für die Goldkatalysatoren optimale Reaktionsbedingungen für die Glucoseoxidation im geregelten Rührkesselreaktor etabliert. Hierdurch konnten eine Produktselektivität von 100 % und eine Wiederverwendbarkeit der Partikel über mindestens zehn Zyklen erreicht werden. Y1 - 2012 U6 - https://doi.org/10.1002/cite.201250393 SN - 0009-286X SN - 1522-2640 (eISSN) N1 - ProcessNet-Jahrestagung 2012 und 30. DECHEMA-Jahrestagung der Biotechnologen, 10. – 13. September 2012, Karlsruhe VL - 84 IS - 8 SP - 1328 PB - Wiley-VCH CY - Weinheim ER - TY - GEN A1 - Sieker, T. A1 - Tippkötter, Nils A1 - Ulber, Roland A1 - Bart, H.-J. A1 - Heinzle, E. T1 - Grüne Bioraffinerie: Ganzheitliche Nutzung von Grassilage für die Herstellung von Grund-und Feinchemikalien T2 - Chemie Ingenieur Technik N2 - Gras hat ein hohes Potenzial als nachwachsender Rohstoff. Bei ungeeigneter Lagerung verderben Gräser allerdings innerhalb weniger Tage. Dieser Nachteil kann durch die Silierung des Grasschnittes behoben werden. Eines der wichtigsten in der Silage enthaltenen Produkte ist die Milchsäure. Um diese für weitere Aufarbeitungsschritte zugänglich zu machen, wird aus der Silage ein Presssaft hergestellt. Die Milchsäure wird aus einem Silagepresssaft mittels Extraktion durch ionische Flüssigkeiten isoliert. Dabei wird zum einen eine reine Milchsäure hergestellt, die z. B. für die Herstellung von Polymilchsäure genutzt werden kann. Zum anderen wird ein weniger aufgereinigter Extrakt gewonnen, der für die fermentative Produktion von L-Lysin und 1,2-Propandiol genutzt werden soll. Im Rahmen des Projekts erfolgt die gentechnische Optimierung von Corynebacterium glutamicum für die Umsetzung von Milchsäurezu L-Lysin. Die im nach der Pressung verbleibenden Presskuchen enthaltenen Grasfasern bestehen zu einem großen Teil aus Polysacchariden. Diese werden hydrolysiert und die dabei freigesetzten Zucker zu Grundchemikalien wie Ethanol oder Itakonsäure fermentiert. Im Rahmen einer vollständigen Nutzung der Silage wird das Raffinat aus der Milchsäureextraktion als Mediumsupplement in der Fermentation eingesetzt, was die Zugabe weiterer Medienbestandteile überflüssig macht. Die Rückstände der Hydrolysen und Fermentationen sollen darüberhinaus für die Herstellung von Biogas genutzt werden. Y1 - 2010 U6 - https://doi.org/10.1002/cite.201050321 SN - 0009-286X SN - 1522-2640 (eISSN) N1 - ProcessNet-Jahrestagung 2010 und 28. DECHEMA-Jahrestagung der Biotechnologen, 21. - 23. September 2010, Eurogress Aachen VL - 82 IS - 9 SP - 1564 PB - Wiley-VCH CY - Weinheim ER - TY - GEN A1 - Tippkötter, Nils A1 - Ulber, Roland T1 - Eine magnetische horizontale Wirbelschicht für die Durchmischung und Rückhaltung von magnetisierbaren Mikropartikeln im Durchfluss T2 - Chemie Ingenieur Technik N2 - Magnetisierbare Partikel als Träger von Katalysatoren können durch Anlegen eines magnetisches Feldes einfach und schnell abgetrennt werden. Die Wiedergewinnung von wertvollen Enzymen unter geringem Energie- und Materialeinsatz der magnetischen Abtrennung eröffnet einen Wettbewerbsvorteil für Produktionsprozesse. Die Abtrennung von magnetisierbaren Partikeln vom Überstand wird üblicherweise entweder durch Anlegen eines äußeren Magnetfelds und der resultierenden Ablagerung der Partikel an den Reaktorwänden oder durch Hochgradientenmagnetseparation (HGMS)durchgeführt. Beide Verfahren resultieren meist in der Bildung eines Filterkuchens aus Magnetpartikeln und den Feststoffen des Reaktionsmediums. Das magnetische horizontale Wirbelbett ermöglicht simultan eine kontinuierliche Reaktionsführung und die Rückhaltung der Partikel im Durchfluss. Die Partikelsuspension fließt durch einen Rohrreaktor, der in einem Magnetfeld mit wechselnden Feldgradienten eingebracht ist. Die Änderung des Magnetfeldgradienten erfolgt entgegen der Strömungsrichtung der Reaktionslösung. Durch alternierende Feldmaxima an den beiden Seiten des Reaktors werden die magnetisierbaren Partikel zu dessen Wänden gezogen. Bei Umkehrung des Feldes wandern die Partikel an die gegenüberliegende Reaktorwand. Durch Wahl einer geeigneten Wechselfrequenz kann eine kontinuierliche Durchmischung und Rückhaltung der Mikropartikel im durchströmten Rohr erreicht werden. Somit können Immobilisierungsreaktionen und Biotransformationen mit den Partikelsystemen im Durchfluss durchgeführt werden. Y1 - 2009 U6 - https://doi.org/10.1002/cite.200950076 SN - 0009-286X SN - 1522-2640 (eISSN) N1 - ProcessNet‐Jahrestagung 2009 und 27. DECHEMA-Jahrestagung der Biotechnologen, 8.- 10. September 2009, Mannheim VL - 81 IS - 8 SP - 1168 PB - Wiley-VCH CY - Weinheim ER - TY - GEN A1 - Tippkötter, Nils A1 - Sieker, T. A1 - Wiesen, S. A1 - Duwe, A. A1 - Roth, J. A1 - Ulber, Roland T1 - Simultane Saccharifizierung und Fermentierung (SSF) sowie Produktion von Aceton, Butanol, Ethanol (ABE) und Dicarbonsäuren aus technischer Cellulose T2 - Chemie Ingenieur Technik N2 - Technische Cellulose wurde als möglicher Rohstoff zur fermentativen Produktbildung untersucht. Hierfür wird Cellulose in der Lignocellulose-Bioraffinerie hergestellt und daraus Hydrolysat gewonnen. Die Prüfung der technischen Hydrolysate als Substrate erfolgte anhand eines breiten Spektrums an Bioprodukten, von Kraftstoffen wie Ethanolund Butanol, bis zu den Dicarbonsäuren Itacon- und Bernsteinsäure. Dabei werden Bakterien, Hefen und Pilze als Produktionsorganismen eingesetzt. Die einzelnen Herstellverfahren stellen unterschiedliche Anforderungen an die Substrathandhabung. Im Fall der Ethanol- und Butanol-Gewinnung kann eine simultane Saccharifizierung und Fermentierung (SSF) durchgeführt werden. Aufgrund der Produkttoxizität erfordert die Butanol-Herstellung dabei eine In-situ-Produktabtrennung durch Lösemittelimprägnierte Partikel. Die Herstellung der beiden Dicarbonsäuren unterscheidet sich in der Sensitivität der verwendeten Mikroorganismen gegenüber Inhibitoren, die in Spuren im Hydrolysat enthalten sind. Die Bernteinsäurebildung mit Actinobacillussuccinogenes kann mit unbehandeltem Hydrolysat erfolgen. Dagegen erfordert die Gewinnung von Itaconsäure mit A. terreus eine Detoxifizierung des Hydrolysats. Insgesamt konnte gezeigt werden, dass sämtliche Bioraffinerie-Hydrolysate als Substrate für unterschiedliche Fermentationen geeignet sind. Y1 - 2014 U6 - https://doi.org/10.1002/cite.201450297 SN - 0009-286X SN - 1522-2640 (eISSN) N1 - ProcessNet-Jahrestagung 2014 und 31. DECHEMA-Jahrestagung der Biotechnologen, 30. September - 2. Oktober 2014, Eurogress Aachen VL - 86 IS - 9 SP - 1518 PB - Wiley-VCH CY - Weinheim ER - TY - GEN A1 - Wiesen, S. A1 - Tippkötter, Nils A1 - Duwe, A. A1 - Ulber, Roland T1 - Aceton-Butanol-Ethanol (ABE)-Fermentation von Organosolv-Holzhydrolysaten T2 - Chemie Ingenieur Technik N2 - Die Lösungsmittelherstellung durch Clostridien konnte wirtschaftlich nicht mit der chemischen Synthese von Lösungsmitteln auf Erdölbasis konkurrieren und wurde in den frühen 1960er Jahren nahezu vollständig eingestellt. Das Interesse an nachwachsenden Rohstoffen hat in den letzten Jahren zu einem Wiederaufleben der ABE-Fermentation geführt. Aufgrund seiner höheren Energiedichte im Vergleich zu Ethanol ist Biobutanol als Energieträgerbesonders interessant und bietet sich z. B. als Produkt einer Bioraffinerie der 2. Generation an. Für die beschriebenen Experimente wird durch das Organosolv-Verfahren aufgeschlossenes Buchenholz verwendet. Der Faserstoff wird mithilfe von CTec2-Enzymen hydrolysiert, wobei der erhaltene Überstand eine Glucosekonzentration von 66 g L⁻¹ aufweist. Auf der Basis dieses Materials können mit Clostridium acetobutylicum Butanol-Ausbeuten erzielt werden, die mit denen unter Verwendung von reinen Zuckern vergleichbar sind. Dem Problem der hohen Produktinhibierung wird mit einer In-situ-Produktaufarbeitung begegnet. Mithilfe von Lösungsmittelimprägnierten Partikeln (SIPs) kann die Produktausbeute drastisch gesteigert werden, indem die gebildeten Lösungsmittel durch das auf dem Partikel imprägnierte Lösungsmittel während der Fermentation extrahiert werden. Zudem wird hierdurch die weitere Produktaufarbeitungstark vereinfacht. Y1 - 2012 U6 - https://doi.org/10.1002/cite.201250262 SN - 0009-286X SN - 1522-2640 (eISSN) N1 - ProcessNet-Jahrestagung 2012 und 30. DECHEMA-Jahrestagung der Biotechnologen, 10. – 13. September 2012, Karlsruhe VL - 84 IS - 8 SP - 1308 PB - Wiley-VCH CY - Weinheim ER - TY - JOUR A1 - Frauenrath, Tobias A1 - Niendorf, Thoralf A1 - Kob, Malte T1 - Acoustic method for synchronization of Magnetic Resonance Imaging (MRI) JF - Acta Acustica N2 - Magnetic Resonance Imaging (MRI) of moving organs requires synchronization with physiological motion or flow, which dictate the viable window for data acquisition. To meet this challenge, this study proposes an acoustic gating device (ACG) that employs acquisition and processing of acoustic signals for synchronization while providing MRI compatibility, immunity to interferences with electro-magnetic and acoustic fields and suitability for MRI at high magnetic field strengths. The applicability and robustness of the acoustic gating approach is examined in a pilot study, where it substitutes conventional ECG-gating for cardiovascular MR. The merits and limitations of the ACG approach are discussed. Implications for MR imaging in the presence of physiological motion are considered including synchronization with other structure- or motion borne sounds. Y1 - 2008 U6 - https://doi.org/10.3813/AAA.918017 SN - 1861-9959 VL - 94 IS - 1 SP - 148 EP - 155 PB - Hirzel CY - Stuttgart ER - TY - CHAP A1 - Eggert, Mathias A1 - Schade, Maximilian A1 - Bröhl, Florian A1 - Moriz, Alexander ED - Mandviwalla, Munir ED - Söllner, Matthias ED - Tuunanen, Tuure T1 - Generating synthetic LiDAR point cloud data for object detection using the Unreal Game Engine T2 - Design Science Research for a Resilient Future (DESRIST 2024) N2 - Object detection based on artificial intelligence is ubiquitous in today’s computer vision research and application. The training of the neural networks for object detection requires large and high-quality datasets. Besides datasets based on image data, datasets derived from point clouds offer several advantages. However, training datasets are sparse and their generation requires a lot of effort, especially in industrial domains. A solution to this issue offers the generation of synthetic point cloud data. Based on the design science research method, the work at hand proposes an approach and its instantiation for generating synthetic point cloud data based on the Unreal Engine. The point cloud quality is evaluated by comparing the synthetic cloud to a real-world point cloud. Within a practical example the applicability of the Unreal Game engine for synthetic point cloud generation could be successfully demonstrated. Y1 - 2024 SN - 978-3-031-61174-2 (Print) SN - 978-3-031-61175-9 (Online) U6 - https://doi.org/10.1007/978-3-031-61175-9_20 N1 - 19th International Conference on Design Science Research in Information Systems and Technology, DESRIST 2024, Trollhättan, Sweden, June 3–5, 2024 SP - 295 EP - 309 PB - Springer CY - Cham ER - TY - GEN A1 - Gräßl, Andreas A1 - Renz, Wolfgang A1 - Hezel, Fabian A1 - Frauenrath, Tobias A1 - Pfeiffer, Harald A1 - Hoffmann, Werner A1 - Kellmann, Peter A1 - Martin, Conrad A1 - Niendorf, Thoralf T1 - Design, evaluation and application of a modular 32 channel transmit/receive surface coil array for cardiac MRI at 7T T2 - 2012 ISMRM Annual Meeting Proceedings N2 - Cardiac MR (CMR) at ultrahigh (≥7.0 T) fields is regarded as one of the most challenging MRI applications. At 7.0 T image quality is not always exclusively defined by signal-to-noise ratio (SNR) and contrast-to-noise ratio (CNR). Detrimental effects bear the potential to spoil the signal-to-noise (SNR) and contrast-to-noise (CNR) benefits of cardiac MR (CMR) at 7.0 T. B₁⁺-inhomogeneities and signal voids represent the main challenges. Various pioneering coil concepts have been proposed to tackle these issues, enabling cardiac MRI at 7.0 T. This includes a trend towards an ever larger number of transmit and receive channels. This approach affords multi-dimensional B₁⁺ modulations to improve B₁⁺ shimming performance and to enhance RF efficiency. Also, parallel imaging benefits from a high number of receive channels enabling two-dimensional acceleration. Realizing the limitations of existing coil designs tailored for UHF CMR and recognizing the opportunities of a many element TX/RX channel architecture this work proposes a modular, two dimensional 32-channel transmit and receive array using loop elements and examines its efficacy for enhanced B¹+ homogeneity and improved parallel imaging performance. Y1 - 2012 SN - 1545-4428 N1 - ISMRM 20th Annual Meeting & Exhibition, 5-11 May 2012, Melbourne, Australia ER - TY - GEN A1 - Tkachenko, Valeriy A1 - von Knobelsdorff-Brenkenhoff, Florian A1 - Kleindienst, Denise A1 - Winter, Lukas A1 - Rieger, Jan A1 - Frauenrath, Tobias A1 - Dieringer, Matthias A. A1 - Santoro, Davide A1 - Niendorf, Thoralf A1 - Schulz-Menger, Jeanette T1 - Cardiovasular MR at 7Tesla: assessment of the right ventricle T2 - 2012 ISMRM Annual Meeting Proceedings N2 - The assessment of the right ventricle (RV) is a challenge in today's cardiology, but of growing clinical impact regarding patient prognosis in different cardiac diseases. The detection and differentiation of small wall motion abnormalities may help to enhance the differentiation of cardiomyopathies including Arrhythmogenic Rightventricular Cardiomyopathy. Cardiovascular magnetic resonance (CMR) at 1.5T is the accepted gold standard for RV quantification. The higher spatial resolution achievable at ultrahigh field strength (UHF) offers the potential to gain new insights into the structure and function of the RV. To approach this goal accurate RV chamber quantification at 7T has to be proven. Consequently this study examines the feasibility of assessment of RV dimensions and function at 7T using improved spatial resolution enabled by the intrinsic sensitivity gain of UHF CMR. For this purpose, a dedicated 16 channel TX/RX RF coil array is used together with 2D CINE fast gradient echo (FGRE) imaging. For comparison RV chamber quantification is conducted at 1.5T using a SSFP based state of the art clinical protocol. Y1 - 2012 SN - 1545-4428 N1 - ISMRM 20th Annual Meeting & Exhibition, 5-11 May 2012, Melbourne, Australia ER - TY - GEN A1 - Frauenrath, Tobias A1 - Fuchs, Katharina A1 - Hezel, Fabian A1 - Dieringer, Matthias A. A1 - Rieger, Jan A1 - Niendorf, Thoralf T1 - Improved cardiac triggering by combining multiple physiological signals: a cardiac MR feasibility study at 7.0 T T2 - 2012 ISMRM Annual Meeting Proceedings N2 - In current clinical cardiovascular MR (CMR) practice cardiac motion is commonly dealt with using ECG based synchronization. However, ECG is corrupted by magneto-hydrodynamic (MHD) effects in magnetic fields. This leads to artifacts in the ECG trace and evokes severe T-wave elevations, which might be misinterpreted as R-waves resulting in erroneous triggering. At (ultra)high field strengths, the propensity of ECG recordings to MHD effects is further pronounced. Pulse oximetry (POX) being inherently sensitive to blood oxygenation provides an alternative approach for cardiac gating. However, due to the travel time of the blood the peak of maximum oxygenation and hence the trigger is delayed by approx. 300 ms with respect to the ECG's R-wave. Also the peak of maximum oxygenation shows a jitter of up to 65 ms. Alternative triggering approaches include acoustic cardiac triggering (ACT). In current clinical practice cardiac gating / triggering commonly relies on using single physiological signals only. Realizing this limitation this study proposes a combined triggering approach which exploits multiple physiological signals including ECG, POX or ACT to track cardiac activity. The feasibility of the coupled approach is examined for LV function assessment at 7.0 T. For this purpose, breath-held 2D-CINE imaging in conjunction with cardiac synchronization was performed paralleled by real time logging of physiological waveforms to track (mis)synchronization between the cardiac cycle and data acquisition. Combinations of the ECG, POX and ACT signals were evaluated and processed in real time to facilitate reliable trigger information. Y1 - 2012 SN - 1545-4428 N1 - ISMRM 20th Annual Meeting & Exhibition, 5-11 May 2012, Melbourne, Australia ER - TY - GEN A1 - Frauenrath, Tobias A1 - Pfeiffer, Harald A1 - Hezel, Fabian A1 - Dieringer, Matthias A. A1 - Winter, Lukas A1 - Gräßl, Andreas A1 - Santoro, Davide A1 - Özerdem, Celal A1 - Renz, Wolfgang A1 - Greiser, Andreas A1 - Niendorf, Thoralf T1 - Lessons learned from cardiac MRI at 7.0 T: LV function assessment at 3.0 T using local multi-channel transceiver coil arrays T2 - 2012 ISMRM Annual Meeting Proceedings N2 - Cardiac MR (CMR) is of proven clinical value but also an area of vigorous ongoing research since image quality is not always exclusively defined by signal-to-noise ratio (SNR) and contrast-to-noise ratio (CNR). Recent developments of CMR at 7.0 T have been driven by pioneering explorations into novel multichannel transmit and receive coil array technology to tackle the challenges B1+-field inhomogeneities, to offset specific-absorption rate (SAR) constraints and to reduce banding artifacts in SSFP imaging. For this study, recognition of the benefits and performance of local surface Tx/Rx-array structures recently established at 7.0 T inspired migration to 3.0 T, where RF inhomogeneities and SAR limitations encountered in routine clinical CMR, though somewhat reduced versus the 7.0 T situation, remain significant. For all these reasons, this study was designed to build and examine the feasibility of a local four channel Tx/Rx cardiac coil array for anatomical and functional cardiac imaging at 3.0 T. For comparison, a homebuilt 4 channel Rx cardiac coil array exhibiting the same geometry as the Tx/Rx coil and a Rx surface coil array were used. Y1 - 2012 SN - 1545-4428 N1 - ISMRM 20th Annual Meeting & Exhibition, 5-11 May 2012, Melbourne, Australia ER - TY - GEN A1 - Lindel, Tomasz Dawid A1 - Greiser, Andreas A1 - Waxman, Patrick A1 - Dietterle, Martin A1 - Seifert, Frank A1 - Fontius, Ulrich A1 - Renz, Wolfgang A1 - Dieringer, Matthias A. A1 - Frauenrath, Tobias A1 - Schulz-Menger, Jeanette A1 - Niendorf, Thoralf A1 - Ittermann, Bernd T1 - Cardiac CINE MRI at 7 T using a transmit array T2 - 2012 ISMRM Annual Meeting Proceedings N2 - With its need for high SNR and short acquisition times, Cardiac MRI (CMR) is an intriguing target application for ultrahigh field MRI. Due to the sheer size of the upper torso, however, the known RF issues of 7T MRI are also most prominent in CMR. Recent years brought substantial progress but the full potential of the ultrahigh field for CMR is yet to be exploited. Parallel transmission (pTx) is a promising approach in this context and several groups have already reported B1 shimming for 7T CMR. In such a static pTx application amplitudes and phases of all Tx channels are adjusted individually but otherwise imaging techniques established in current clinical practice 1.5 T and 3 T are applied. More advanced forms of pTx as spatially selective excitation (SSE) using Transmit SENSE promise additional benefits like faster imaging with reduced fields of view or improved SAR control. SSE requires the full dynamic capabilities of pTx, however, and for the majority of today's implemented pTx hardware the internal synchronization of the Tx array does not easily permit external triggering as needed for CMR. Here we report a software solution to this problem and demonstrate the feasibility of CINE CMR at 7 T using a Tx array. Y1 - 2012 SN - 1545-4428 N1 - ISMRM 20th Annual Meeting & Exhibition, 5-11 May 2012, Melbourne, Australia ER - TY - GEN A1 - Waiczies, Helmar A1 - Kühne, André A1 - Winter, Lukas A1 - Frauenrath, Tobias A1 - Hoffmann, Werner A1 - Ittermann, Bernd A1 - Waiczies, Sonia A1 - Niendorf, Thoralf T1 - Towards theranostics of rheumatoid arthritis: 1H/19F imaging of non-steroidal anti-inflammatory drugs in hand and wrist at 7 Tesla T2 - 2013 ISMRM Annual Meeting Proceedings N2 - We have developed a double-tuned ¹H/¹⁹F birdcage resonator dedicated for hand and wrist imaging at 7 T to locally image non-steroidal anti-inflammatory drugs (NSAID) such as 2-{[3-(Trifluoromethyl) phenyl]amino}benzoic acid. The preliminary in vivo images acquired by the double-tuned ¹H/¹⁹F birdcage resonator demonstrate the feasibility for ¹H/¹⁹F hand- and wrist-imaging at 7 T. While the diagnostic quality of the coil needs to be assessed in patients with inflammatory rheumatoid disease, first ¹⁹F images of the NSAID are encouraging, and point towards the prospect of applying ¹⁹F-MRI to visualize and quantify the concentration of therapeutically-active compound at the sites of inflammation. Y1 - 2013 SN - 1545-4428 N1 - ISMRM 21st Annual Meeting & Exhibition, 20-26 April 2013, Salt Lake City, Utah, USA ER - TY - GEN A1 - Rothkranz, Berit A1 - Krafft, Simone A1 - Tippkötter, Nils T1 - Media optimization for sustainable fuel production: How to produce biohydrogen from renewable resources with Thermotoga neapolitana T2 - Chemie Ingenieur Technik N2 - Hydrogen is playing an increasingly important role in research and politics as an energy carrier of the future. Since hydrogen has commonly been produced from methane by steam reforming, the need for climate-friendly, alternative production routes is emerging. In addition to electrolysis, fermentative routes for the production of so-called biohydrogen are "green" alternatives. The application of microorganisms offers the advantage of sustainable production from renewable resources using easily manageable technologies. In this project, the hyperthermophilic, anaerobic microorganism Thermotoga neapolitana is used for the productio nof biohydrogen from renewable resources. The enzymatically hydrolyzed resources were used in fermentation leading to yield coefficients of 1.8 mole H₂ per mole glucose when using hydrolyzed straw and ryegrass supplemented with medium, respectively. These results are similar to the hydrogen yields when using Thermotoga basal medium with glucose (TBGY) as control group. In order to minimize the supplementation of the hydrolysate and thus increase the economic efficiency of the process, the essential media components were identified. The experiments revealed NaCl, KCl, and glucose as essential components for cell growth as well as biohydrogen production. When excluding NaCl, a decrease of 96% in hydrogen production occured. Y1 - 2022 U6 - https://doi.org/10.1002/cite.202255305 SN - 0009-286X SN - 1522-2640 (eISSN) N1 - ProcessNet and DECHEMA‐BioTechNet Jahrestagungen 2022 together with 13th ESBES Symposium 2022, 12. - 15. September 2022, Eurogress Aachen VL - 94 IS - 9 SP - 1298 EP - 1299 PB - Wiley-VCH CY - Weinheim ER - TY - GEN A1 - Varriale, Ludovica A1 - Kuka, Katrin A1 - Tippkötter, Nils A1 - Ulber, Roland T1 - Use of a green biomass in a biorefinery platform T2 - Chemie Ingenieur Technik N2 - The emerging environmental issues due to the use of fossil resources are encouraging the exploration of new renewable resources. Biomasses are attracting more interest due to the low environmental impacts, low costs, and high availability on earth. In this scenario, green biorefineries are a promising platform in which green biomasses are used as feedstock. Grasses are mainly composed of cellulose and hemicellulose, and lignin is available in a small amount. In this work, a perennial ryegrass was used as feedstock to develop a green bio-refinery platform. Firstly, the grass was mechanically pretreated, thus obtaining a press juice and a press cake fraction. The press juice has high nutritional values and can be employed as part of fermentation media. The press cake can be employed as a substrate either in enzymatic hydrolysis or in solid-state fermentation. The overall aim of this work was to demonstrate different applications of both the liquid and the solid fractions. For this purpose, the filamentous fungus A. niger and the yeast Y. lipolythica were selected for their ability to produce citric acid. Finally, the possibility was assessed to use the press juice as part of fermentation media to cultivate S. cerevisiae and lactic acid bacteria for ethanol and lactic acid fermentation. Y1 - 2022 U6 - https://doi.org/10.1002/cite.202255095 SN - 0009-286X SN - 1522-2640 (eISSN) N1 - ProcessNet and DECHEMA‐BioTechNet Jahrestagungen 2022 together with 13th ESBES Symposium 2022, 12. - 15. September 2022, Eurogress Aachen VL - 94 IS - 9 SP - 1299 PB - Wiley-VCH CY - Weinheim ER - TY - GEN A1 - Krafft, Simone A1 - Kuka, Katrin A1 - Ulber, Roland A1 - Tippkötter, Nils T1 - Utilization of Lolium perenne varieties as a renewable substrate for single-cell proteins, lactate, and composite materials T2 - Chemie Ingenieur Technik N2 - Lolium perenne (perennial ryegrass) is aproductive and high-quality forage grass indigenous to Southern Europe, temperate Asia, and North Africa. Nowadays it is widespread and the dominant grass species on green areas in temperate climates. This abundant source of biomass is suitable for the development of bioeconomic processes because of its high cellulose and water-soluble carbohydrate content. In this work, novel breeds of the perennial ryegrass are being examined with regards to their quality parameters and biotechnological utilization options within the context of bioeconomy. Three processing operations are presented. In the first process, the perennial ryegrass is pretreated by pressing or hydrothermal extraction to derive glucosevia subsequent enzymatic hydrolysis of cellulose. A yield of up to 82 % glucose was achieved when using the hydrothermal ex-traction as pretreatment. In a second process, the ryegrass is used to produce lactic acid in high concentrations. The influence of the growth conditions and the cutting time on the carboxylic acid yield is investigated. A yield of lactic acid of above 150 g kg⁻¹ dry matter was achieved. The third process is to use Lolium perenne as a substrate in the fermentation of K. marxianus for the microbial production of single-cell proteins. The perennial ryegrass is screw-pressed and the press juice is used as medium. When supplementing the press juice with yeast media components, a biomass concentration of up to 16 g L⁻¹ could be achieved. Y1 - 2022 U6 - https://doi.org/10.1002/cite.202255306 SN - 0009-286X SN - 1522-2640 (eISSN) N1 - ProcessNet and DECHEMA‐BioTechNet Jahrestagungen 2022 together with 13th ESBES Symposium 2022, 12. - 15. September 2022, Eurogress Aachen VL - 94 IS - 9 SP - 1303 EP - 1304 PB - Wiley-VCH CY - Weinheim ER - TY - GEN A1 - Braun, Lena A1 - Krafft, Simone A1 - Tippkötter, Nils T1 - Combined supercritical carbon dioxide extraction and chromatography of the algae fatty linoleic and linolenic acid T2 - Chemie Ingenieur Technik N2 - A method for the integrated extraction and separation of fatty acids from algae using supercritical CO2 is presented. Desmodesmus obliquus and Chlorella sorokiniana were used as algae. First, a method for chromatographic separation of fatty acids of different degrees of saturation was established and optimized. Then, an integrated method for supercritical extraction was developed for both algal species. It was also verified whether prior cell disruption was beneficial for extraction. In developing the method for chromatographic separation, statistical experimental design was used to determine the optimal parameter settings. The methanol content in the mobile phase proved to be the most important parameter for successful separation of the three unsaturated fatty acids oleic acid, linoleic acid, and linolenic acid. Supercritical extraction with dried algae showed that about four times more fatty acids can be extracted from C. sorokiniana relative to the dry mass used. Y1 - 2022 U6 - https://doi.org/10.1002/cite.202255308 SN - 0009-286X SN - 1522-2640 (eISSN) N1 - ProcessNet and DECHEMA‐BioTechNet Jahrestagungen 2022 together with 13th ESBES Symposium 2022, 12. - 15. September 2022, Eurogress Aachen VL - 94 IS - 9 SP - 1304 PB - Wiley-VCH CY - Weinheim ER - TY - RPRT A1 - Tippkötter, Nils T1 - TreBec - Herstellung eines Mehrwegbechers aus Treber : Sachbericht zum Verwendungsnachweis N2 - Laufzeit des Vorhabens und Berichtszeitraum: 01.10.2020-30.09.2021 Y1 - 2021 U6 - https://doi.org/10.2314/KXP:1858723302 N1 - Förderkennzeichen BMBF 031B1037 PB - FH Aachen CY - Jülich ER - TY - JOUR A1 - Timme, Michael T1 - Kaufvertrag: Das Zusammentreffen von Beschaffenheitsvereinbarung und Gewährleistungsausschluss – ein Spannungsverhältnis JF - Monatsschrift für Deutsches Recht N2 - Wer A sagt, muss zumindest im Kaufrecht nicht immer B sagen: Es kommt nicht selten vor, dass sich in einem Kaufvertrag einerseits ein wirksamer Ausschluss der Gewährleistung des Verkäufers für Sachmängel findet, die Parteien aber andererseits gleichwohl eine Beschaffenheitsvereinbarung für bestimmte Eigenschaften vertraglich festlegen. In diesem Problemfeld führt eine aktuelle Entscheidung des BGH zu weiteren Klärungen für die Praxis (BGH, Urt. v. 10.4.2024 – VIII ZR 161/23, MDR 2024, 706). Der folgende Beitrag setzt sich mit den vielfältigen Aspekten der Entscheidung auseinander und erläutert, aus welchen Gründen der BGH dem Käufer einige goldene Brücken für einen Schadensersatzanspruch gebaut hat. Y1 - 2024 U6 - https://doi.org/10.9785/mdtr-2024-781203 SN - 2194-4202 (online) SN - 0340-1812 (print) VL - 78 IS - 12 SP - 745 EP - 748 PB - Verlag Dr. Otto Schmidt CY - Köln ER - TY - CHAP A1 - Niendorf, Thoralf A1 - Winter, Lukas A1 - Frauenrath, Tobias ED - Millis, Richard T1 - Electrocardiogram in an MRI environment: Clinical needs, practical considerations, safety implications, technical solutions and fFuture directions T2 - Advances in Electrocardiograms - Methods and Analysis Y1 - 2012 SN - 978-953-307-923-3 (print) SN - 978-953-51-6762-4 (eBook) U6 - https://doi.org/10.5772/24340 SP - 309 EP - 324 PB - IntechOpen CY - London ER - TY - JOUR A1 - Özsoylu, Dua A1 - Aliazizi, Fereshteh A1 - Wagner, Patrick A1 - Schöning, Michael Josef T1 - Template bacteria-free fabrication of surface imprinted polymer-based biosensor for E. coli detection using photolithographic mimics: Hacking bacterial adhesion JF - Biosensors and Bioelectronics N2 - As one class of molecular imprinted polymers (MIPs), surface imprinted polymer (SIP)-based biosensors show great potential in direct whole-bacteria detection. Micro-contact imprinting, that involves stamping the template bacteria immobilized on a substrate into a pre-polymerized polymer matrix, is the most straightforward and prominent method to obtain SIP-based biosensors. However, the major drawbacks of the method arise from the requirement for fresh template bacteria and often non-reproducible bacteria distribution on the stamp substrate. Herein, we developed a positive master stamp containing photolithographic mimics of the template bacteria (E. coli) enabling reproducible fabrication of biomimetic SIP-based biosensors without the need for the “real” bacteria cells. By using atomic force and scanning electron microscopy imaging techniques, respectively, the E. coli-capturing ability of the SIP samples was tested, and compared with non-imprinted polymer (NIP)-based samples and control SIP samples, in which the cavity geometry does not match with E. coli cells. It was revealed that the presence of the biomimetic E. coli imprints with a specifically designed geometry increases the sensor E. coli-capturing ability by an “imprinting factor” of about 3. These findings show the importance of geometry-guided physical recognition in bacterial detection using SIP-based biosensors. In addition, this imprinting strategy was employed to interdigitated electrodes and QCM (quartz crystal microbalance) chips. E. coli detection performance of the sensors was demonstrated with electrochemical impedance spectroscopy (EIS) and QCM measurements with dissipation monitoring technique (QCM-D). KW - Surface imprinted polymer KW - E. coli detection KW - Photolithographic mimics KW - Master stamp KW - Quartz crystal microbalance Y1 - 2024 U6 - https://doi.org/10.1016/j.bios.2024.116491 SN - 1873-4235 (eISSN) SN - 0956-5663 N1 - Corresponding author: Michael J. Schöning VL - 261 PB - Elsevier CY - Amsterdam ER - TY - JOUR A1 - Heinrichs, Uwe A1 - Utting, Jane F. A1 - Frauenrath, Tobias A1 - Hezel, Fabian A1 - Krombach, Gabriele A. A1 - Hodenius, Michael A. J. A1 - Kozerke, Sebastian A1 - Niendorf, Thoralf T1 - Myocardial T2 mapping free of distortion using susceptibility-weighted fast spin-echo imaging: A feasibility study at 1.5 T and 3.0 T JF - Magnetic Resonance in Medicine N2 - This study demonstrates the feasibility of applying free-breathing, cardiac-gated, susceptibility-weighted fast spin-echo imaging together with black blood preparation and navigator-gated respiratory motion compensation for anatomically accurate T₂ mapping of the heart. First, T₂ maps are presented for oil phantoms without and with respiratory motion emulation (T₂ = (22.1 ± 1.7) ms at 1.5 T and T₂ = (22.65 ± 0.89) ms at 3.0 T). T₂ relaxometry of a ferrofluid revealed relaxivities of R2 = (477.9 ± 17) mM⁻¹s⁻¹ and R2 = (449.6 ± 13) mM⁻¹s⁻¹ for UFLARE and multiecho gradient-echo imaging at 1.5 T. For inferoseptal myocardial regions mean T₂ values of 29.9 ± 6.6 ms (1.5 T) and 22.3 ± 4.8 ms (3.0 T) were estimated. For posterior myocardial areas close to the vena cava T₂-values of 24.0 ± 6.4 ms (1.5 T) and 15.4 ± 1.8 ms (3.0 T) were observed. The merits and limitations of the proposed approach are discussed and its implications for cardiac and vascular T₂-mapping are considered. Y1 - 2009 U6 - https://doi.org/10.1002/mrm.22054 SN - 1522-2594 VL - 62 IS - 3 SP - 822 EP - 828 PB - Wiley-Liss CY - New York ER - TY - JOUR A1 - Kob, Malte A1 - Frauenrath, Tobias T1 - A system for parallel measurement of glottis opening and larynx position JF - Biomedical Signal Processing and Control N2 - The simultaneous assessment of glottal dynamics and larynx position can be beneficial for the diagnosis of disordered voice or speech production and swallowing. Up to now, methods either concentrate on assessment of the glottis opening using optical, acoustical or electrical (electroglottography, EGG) methods, or on visualisation of the larynx position using ultrasound, computer tomography or magnetic resonance imaging techniques. The method presented here makes use of a time-multiplex measurement approach of space-resolved transfer impedances through the larynx. The fast sequence of measurements allows a quasi simultaneous assessment of both larynx position and EGG signal using up to 32 transmit–receive signal paths. The system assesses the dynamic opening status of the glottis as well as the vertical and back/forward motion of the larynx. Two electrode-arrays are used for the measurement of the electrical transfer impedance through the neck in different directions. From the acquired data the global and individual conductivity is calculated as well as a 2D point spatial representation of the minimum impedance. The position information is shown together with classical EGG signals allowing a synchronous visual assessment of glottal area and larynx position. A first application to singing voice analysis is presented that indicate a high potential of the method for use as a non-invasive tool in the diagnosis of voice, speech, and swallowing disorders. KW - EGG KW - Transfer impedance KW - Tomography KW - Larynx position KW - Voice assessment Y1 - 2009 U6 - https://doi.org/10.1016/j.bspc.2009.03.004 SN - 1746-8108 VL - 4 IS - 3 SP - 221 EP - 228 PB - Elsevier CY - Amsterdam ER - TY - JOUR A1 - von Knobelsdorf-Brenkenhoff, Florian A1 - Frauenrath, Tobias A1 - Prothmann, Marcel A1 - Dieringer, Matthias A. A1 - Hezel, Fabian A1 - Renz, Wolfgang A1 - Kretschel, Kerstin A1 - Niendorf, Thoralf A1 - Schulz-Menger, Jeanette T1 - Cardiac chamber quantification using magnetic resonance imaging at 7 Tesla—a pilot study N2 - Objectives Interest in cardiovascular magnetic resonance (CMR) at 7 T is motivated by the expected increase in spatial and temporal resolution, but the method is technically challenging. We examined the feasibility of cardiac chamber quantification at 7 T. Methods A stack of short axes covering the left ventricle was obtained in nine healthy male volunteers. At 1.5 T, steady-state free precession (SSFP) and fast gradient echo (FGRE) cine imaging with 7 mm slice thickness (STH) were used. At 7 T, FGRE with 7 mm and 4 mm STH were applied. End-diastolic volume, end-systolic volume, ejection fraction and mass were calculated. Results All 7 T examinations provided excellent blood/myocardium contrast for all slice directions. No significant difference was found regarding ejection fraction and cardiac volumes between SSFP at 1.5 T and FGRE at 7 T, while volumes obtained from FGRE at 1.5 T were underestimated. Cardiac mass derived from FGRE at 1.5 and 7 T was larger than obtained from SSFP at 1.5 T. Agreement of volumes and mass between SSFP at 1.5 T and FGRE improved for FGRE at 7 T when combined with an STH reduction to 4 mm. Conclusions This pilot study demonstrates that cardiac chamber quantification at 7 T using FGRE is feasible and agrees closely with SSFP at 1.5 T. Y1 - 2010 U6 - https://doi.org/10.1007/s00330-010-1888-2 SN - 0938-7994 VL - 20 SP - 2844 EP - 2852 PB - Springer CY - Berlin, Heidelberg ER - TY - JOUR A1 - Frauenrath, Tobias A1 - Hezel, Fabian A1 - Renz, Wolfgang A1 - de Geyer d'Orth, Thibaut A1 - Dieringer, Matthias A1 - von Knobelsdorf-Brenkenhoff, Florian A1 - Prothmann, Marcel A1 - Schulz-Menger, Jeanette A1 - Niendorf, Thoralf T1 - Acoustic cardiac triggering: a practical solution for synchronization and gating of cardiovascular magnetic resonance at 7 Tesla JF - Journal of Cardiovascular Magnetic Resonance N2 - Background To demonstrate the applicability of acoustic cardiac triggering (ACT) for imaging of the heart at ultrahigh magnetic fields (7.0 T) by comparing phonocardiogram, conventional vector electrocardiogram (ECG) and traditional pulse oximetry (POX) triggered 2D CINE acquisitions together with (i) a qualitative image quality analysis, (ii) an assessment of the left ventricular function parameter and (iii) an examination of trigger reliability and trigger detection variance derived from the signal waveforms. Results ECG was susceptible to severe distortions at 7.0 T. POX and ACT provided waveforms free of interferences from electromagnetic fields or from magneto-hydrodynamic effects. Frequent R-wave mis-registration occurred in ECG-triggered acquisitions with a failure rate of up to 30% resulting in cardiac motion induced artifacts. ACT and POX triggering produced images free of cardiac motion artefacts. ECG showed a severe jitter in the R-wave detection. POX also showed a trigger jitter of approximately Δt = 72 ms which is equivalent to two cardiac phases. ACT showed a jitter of approximately Δt = 5 ms only. ECG waveforms revealed a standard deviation for the cardiac trigger offset larger than that observed for ACT or POX waveforms. Image quality assessment showed that ACT substantially improved image quality as compared to ECG (image quality score at end-diastole: ECG = 1.7 ± 0.5, ACT = 2.4 ± 0.5, p = 0.04) while the comparison between ECG vs. POX gated acquisitions showed no significant differences in image quality (image quality score: ECG = 1.7 ± 0.5, POX = 2.0 ± 0.5, p = 0.34). Conclusions The applicability of acoustic triggering for cardiac CINE imaging at 7.0 T was demonstrated. ACT's trigger reliability and fidelity are superior to that of ECG and POX. ACT promises to be beneficial for cardiovascular magnetic resonance at ultra-high field strengths including 7.0 T. KW - Interval Time Series KW - Image Quality Score KW - Image Quality Assessment KW - Sound Pressure Level KW - Cardiovascular Magnetic Resonance Y1 - 2010 U6 - https://doi.org/10.1186/1532-429X-12-67 SN - 1532-429X VL - 12 IS - 1 PB - Elsevier CY - Amsterdam ER - TY - JOUR A1 - Dieringer, Matthias A. A1 - Renz, Wolfgang A1 - Lindel, Tomasz D. A1 - Seifert, Frank A1 - Frauenrath, Tobias A1 - von Knobelsdorf-Brenkenhoff, Florian A1 - Waiczies, Helmar A1 - Hoffmann, Werner A1 - Rieger, Jan A1 - Pfeiffer, Harald A1 - Ittermann, Bernd A1 - Schulz-Menger, Jeanette A1 - Niendorf, Thoralf T1 - Design and application of a four-channel transmit/receive surface coil for functional cardiac imaging at 7T JF - Journal of Magnetic Resonance Imaging N2 - Purpose To design and evaluate a four-channel cardiac transceiver coil array for functional cardiac imaging at 7T. Materials and Methods A four-element cardiac transceiver surface coil array was developed with two rectangular loops mounted on an anterior former and two rectangular loops on a posterior former. specific absorption rate (SAR) simulations were performed and a Burn:x-wiley:10531807:media:JMRI22451:tex2gif-stack-1 calibration method was applied prior to obtain 2D FLASH CINE (mSENSE, R = 2) images from nine healthy volunteers with a spatial resolution of up to 1 × 1 × 2.5 mm3. Results Tuning and matching was found to be better than 10 dB for all subjects. The decoupling (S21) was measured to be >18 dB between neighboring loops, >20 dB for opposite loops, and >30 dB for other loop combinations. SAR values were well within the limits provided by the IEC. Imaging provided clinically acceptable signal homogeneity with an excellent blood-myocardium contrast applying the Burn:x-wiley:10531807:media:JMRI22451:tex2gif-stack-2 calibration approach. Conclusion A four-channel cardiac transceiver coil array for 7T was built, allowing for cardiac imaging with clinically acceptable signal homogeneity and an excellent blood-myocardium contrast. Minor anatomic structures, such as pericardium, mitral, and tricuspid valves and their apparatus, as well as trabeculae, were accurately delineated. Y1 - 2011 U6 - https://doi.org/10.1002/jmri.22451 SN - 1522-2586 VL - 33 IS - 3 SP - 736 EP - 741 PB - Wiley-Liss CY - New York ER - TY - JOUR A1 - Martin, Conrad A1 - Frauenrath, Tobias A1 - Özerdem, Celal A1 - Renz, Wolfgang A1 - Niendorf, Thoralf T1 - Development and evaluation of a small and mobile Magneto Alert Sensor (MALSE) to support safety requirements for magnetic resonance imaging JF - European Radiology N2 - Objective The purpose of this study is to (i) design a small and mobile Magnetic field ALert SEnsor (MALSE), (ii) to carefully evaluate its sensors to their consistency of activation/deactivation and sensitivity to magnetic fields, and (iii) to demonstrate the applicability of MALSE in 1.5 T, 3.0 T and 7.0 T MR fringe field environments. Methods MALSE comprises a set of reed sensors, which activate in response to their exposure to a magnetic field. The activation/deactivation of reed sensors was examined by moving them in/out of the fringe field generated by 7TMR. Results The consistency with which individual reed sensors would activate at the same field strength was found to be 100% for the setup used. All of the reed switches investigated required a substantial drop in ambient magnetic field strength before they deactivated. Conclusions MALSE is a simple concept for alerting MRI staff to a ferromagnetic object being brought into fringe magnetic fields which exceeds MALSEs activation magnetic field. MALSE can easily be attached to ferromagnetic objects within the vicinity of a scanner, thus creating a barrier for hazardous situations induced by ferromagnetic parts which should not enter the vicinity of an MR-system to occur. KW - MRI KW - MR safety KW - Magneto alert sensor KW - High field MRI KW - Uktrahigh field MRI Y1 - 2011 U6 - https://doi.org/10.1007/s00330-011-2153-z SN - 1432-1084 VL - 21 SP - 2187 EP - 2192 PB - Springer CY - Berlin, Heidelberg ER - TY - JOUR A1 - Grande, Marion A1 - Meffert, Elisabeth A1 - Schoenberger, Eva A1 - Jung, Stefanie A1 - Frauenrath, Tobias A1 - Huber, Walter A1 - Hussmann, Katja A1 - Moormann, Mareike A1 - Heim, Stefan T1 - From a concept to a word in a syntactically complete sentence: An fMRI study on spontaneous language production in an overt picture description task JF - NeuroImage N2 - Spontaneous language has rarely been subjected to neuroimaging studies. This study therefore introduces a newly developed method for the analysis of linguistic phenomena observed in continuous language production during fMRI. Most neuroimaging studies investigating language have so far focussed on single word or — to a smaller extent — sentence processing, mostly due to methodological considerations. Natural language production, however, is far more than the mere combination of words to larger units. Therefore, the present study aimed at relating brain activation to linguistic phenomena like word-finding difficulties or syntactic completeness in a continuous language fMRI paradigm. A picture description task with special constraints was used to provoke hesitation phenomena and speech errors. The transcribed speech sample was segmented into events of one second and each event was assigned to one category of a complex schema especially developed for this purpose. The main results were: conceptual planning engages bilateral activation of the precuneus. Successful lexical retrieval is accompanied – particularly in comparison to unsolved word-finding difficulties – by the left middle and superior temporal gyrus. Syntactic completeness is reflected in activation of the left inferior frontal gyrus (IFG) (area 44). In sum, the method has proven to be useful for investigating the neural correlates of lexical and syntactic phenomena in an overt picture description task. This opens up new prospects for the analysis of spontaneous language production during fMRI. Y1 - 2012 U6 - https://doi.org/10.1016/j.neuroimage.2012.03.087 SN - 1522-2586 VL - 61 IS - 3 SP - 702 EP - 714 PB - Elsevier CY - Amsterdam ER - TY - JOUR A1 - Frauenrath, Tobias A1 - Fuchs, Katharina A1 - Dieringer, Matthias A. A1 - Özerdem, Celal A1 - Patel, Nishan A1 - Renz, Wolfgang A1 - Greiser, Andreas A1 - Elgeti, Thomas A1 - Niendorf, Thoralf T1 - Detailing the use of magnetohydrodynamic effects for synchronization of MRI with the cardiac cycle: A feasibility study JF - Journal of Magnetic Resonance Imaging N2 - Purpose: To investigate the feasibility of using magnetohydrodynamic (MHD) effects for synchronization of magnetic resonance imaging (MRI) with the cardiac cycle. Materials and Methods: The MHD effect was scrutinized using a pulsatile flow phantom at B0 = 7.0 T. MHD effects were examined in vivo in healthy volunteers (n = 10) for B0 ranging from 0.05–7.0 T. Noncontrast-enhanced MR angiography (MRA) of the carotids was performed using a gated steady-state free-precession (SSFP) imaging technique in conjunction with electrocardiogram (ECG) and MHD synchronization. Results: The MHD potential correlates with flow velocities derived from phase contrast MRI. MHD voltages depend on the orientation between B0 and the flow of a conductive fluid. An increase in the interelectrode spacing along the flow increases the MHD potential. In vivo measurement of the MHD effect provides peak voltages of 1.5 mV for surface areas close to the common carotid artery at B0 = 7.0 T. Synchronization of MRI with the cardiac cycle using MHD triggering is feasible. MHD triggered MRA of the carotids at 3.0 T showed an overall image quality and richness of anatomic detail, which is comparable to ECG-triggered MRAs. Conclusion: This feasibility study demonstrates the use of MHD effects for synchronization of MR acquisitions with the cardiac cycle. J. Magn. Reson. Imaging 2012;36:364–372. © 2012 Wiley Periodicals, Inc. Y1 - 2012 U6 - https://doi.org/10.1002/jmri.23634 SN - 1522-2586 VL - 36 IS - 2 SP - 364 EP - 372 PB - Wiley-Liss CY - New York ER - TY - JOUR A1 - Gräßl, Andreas A1 - Renz, Wolfgang A1 - Hezel, Fabian A1 - Dieringer, Matthias A. A1 - Winter, Lukas A1 - Özerdem, Celal A1 - Rieger, Jan A1 - Kellmann, Peter A1 - Santoro, Davide A1 - Lindel, Tomasz D. A1 - Frauenrath, Tobias A1 - Pfeiffer, Harald A1 - Niendorf, Thoralf T1 - Modular 32-channel transceiver coil array for cardiac MRI at 7.0T JF - Magnetic Resonance in Medicine N2 - Purpose To design and evaluate a modular transceiver coil array with 32 independent channels for cardiac MRI at 7.0T. Methods The modular coil array comprises eight independent building blocks, each containing four transceiver loop elements. Numerical simulations were used for B1+ field homogenization and radiofrequency (RF) safety validation. RF characteristics were examined in a phantom study. The array's suitability for accelerated high spatial resolution two-dimensional (2D) FLASH CINE imaging of the heart was examined in a volunteer study. Results Transmission field adjustments and RF characteristics were found to be suitable for the volunteer study. The signal-to-noise intrinsic to 7.0T together with the coil performance afforded a spatial resolution of 1.1 × 1.1 × 2.5 mm3 for 2D CINE FLASH MRI, which is by a factor of 6 superior to standardized CINE protocols used in clinical practice at 1.5T. The 32-channel transceiver array supports one-dimensional acceleration factors of up to R = 4 without impairing image quality significantly. Conclusion The modular 32-channel transceiver cardiac array supports accelerated and high spatial resolution cardiac MRI. The array is compatible with multichannel transmission and provides a technological basis for future clinical assessment of parallel transmission techniques at 7.0T. Y1 - 2013 U6 - https://doi.org/10.1002/mrm.24903 SN - 1522-2594 VL - 72 IS - 1 SP - 276 EP - 290 PB - Wiley-Liss CY - New York ER - TY - PAT A1 - Frauenrath, Tobias A1 - Niendorf, Thoralf T1 - MRT-Vorrichtung und Verfahren zum Betreiben einer MRT-Vorrichtung T1 - Magnetic resonance tomography (MRT) apparatus and method of operating a magnetic resonance (MR) apparatus T1 - Appareil de tomographie par résonance magnétique et procédé de fonctionnement d'un appareil à résonance magnétique N2 - A magnetic resonance tomography (MRT) apparatus (1) for the examination of a body (14) comprises parameter acquisition devices (13) for the acquisition of cardiovascular parameters of the body (14) and a control device (15) in communication with the parameter acquisition devices (13) for synchronizing the imaging, wherein the control device (15) is adapted to analyse the data of at least two parameter acquisition devices (13) and to output a control signal based on the analysis. Y1 - 2012 ER - TY - JOUR A1 - Hengsbach, Jan-Niklas A1 - Engel, Mareike A1 - Cwienczek, Marcel A1 - Stiefelmaier, Judith A1 - Tippkötter, Nils A1 - Ulber, Roland T1 - Scalable unseparated bioelectrochemical reactors by using a carbon fiber brush as stirrer and working electrode JF - ChemElectroChem N2 - The concept of energy conversion into platform chemicals using bioelectrochemical systems (BES) has gained increasing attention in recent years, as the technology simultaneously provides an opportunity for sustainable chemical production and tackles the challenge of Power-to-X technologies. There are many approaches to realize the industrial scale of BES. One concept is to equip standard bioreactors with static electrodes. However, large installations resulted in a negative influence on various reactor parameters. In this study, we present a new single-chamber BES based on a stirred tank reactor in which the stirrer was replaced by a carbon fiber brush, performing the functions of the working electrode and the stirrer. The reactor is characterized in abiotic studies and electro-fermentations with Clostridium acetobutylicum. Compared to standard reactors an increase in butanol production of 20.14±3.66 % shows that the new BES can be efficiently used for bioelectrochemical processes. Y1 - 2023 U6 - https://doi.org/10.1002/celc.202300440 SN - 2196-0216 VL - 10 IS - 21 PB - Wiley-VCH CY - Weinheim ER - TY - JOUR A1 - Oehlenschläger, Katharina A1 - Volkmar, Marianne A1 - Stiefelmaier, Judith A1 - Langsdorf, Alexander A1 - Holtmann, Dirk A1 - Tippkötter, Nils A1 - Ulber, Roland T1 - New insights into the influence of pre-culture on robust solvent production of C. acetobutylicum JF - Applied Microbiology and Biotechnology N2 - Clostridia are known for their solvent production, especially the production of butanol. Concerning the projected depletion of fossil fuels, this is of great interest. The cultivation of clostridia is known to be challenging, and it is difficult to achieve reproducible results and robust processes. However, existing publications usually concentrate on the cultivation conditions of the main culture. In this paper, the influence of cryo-conservation and pre-culture on growth and solvent production in the resulting main cultivation are examined. A protocol was developed that leads to reproducible cultivations of Clostridium acetobutylicum. Detailed investigation of the cell conservation in cryo-cultures ensured reliable cell growth in the pre-culture. Moreover, a reason for the acid crash in the main culture was found, based on the cultivation conditions of the pre-culture. The critical parameter to avoid the acid crash and accomplish the shift to the solventogenesis of clostridia is the metabolic phase in which the cells of the pre-culture were at the time of inoculation of the main culture; this depends on the cultivation time of the pre-culture. Using cells from the exponential growth phase to inoculate the main culture leads to an acid crash. To achieve the solventogenic phase with butanol production, the inoculum should consist of older cells which are in the stationary growth phase. Considering these parameters, which affect the entire cultivation process, reproducible results and reliable solvent production are ensured. KW - Pre-culture KW - Metabolic shift KW - Acid crash KW - C. acetobutylicum KW - ABE KW - Butanol Y1 - 2024 U6 - https://doi.org/10.1007/s00253-023-12981-8 SN - 1432-0614 VL - 108 PB - Springer CY - Berlin, Heidelberg ER - TY - JOUR A1 - Tix, Julian A1 - Moll, Fabian A1 - Krafft, Simone A1 - Betsch, Matthias A1 - Tippkötter, Nils T1 - Hydrogen production from enzymatic pretreated organic waste with thermotoga neapolitana JF - Energies N2 - Biomass from various types of organic waste was tested for possible use in hydrogen production. The composition consisted of lignified samples, green waste, and kitchen scraps such as fruit and vegetable peels and leftover food. For this purpose, the enzymatic pretreatment of organic waste with a combination of five different hydrolytic enzymes (cellulase, amylase, glucoamylase, pectinase and xylase) was investigated to determine its ability to produce hydrogen (H2) with the hydrolyzate produced here. In course, the anaerobic rod-shaped bacterium T. neapolitana was used for H2 production. First, the enzymes were investigated using different substrates in preliminary experiments. Subsequently, hydrolyses were carried out using different types of organic waste. In the hydrolysis carried out here for 48 h, an increase in glucose concentration of 481% was measured for waste loads containing starch, corresponding to a glucose concentration at the end of hydrolysis of 7.5 g·L−1. In the subsequent set fermentation in serum bottles, a H2 yield of 1.26 mmol H2 was obtained in the overhead space when Terrific Broth Medium with glucose and yeast extract (TBGY medium) was used. When hydrolyzed organic waste was used, even a H2 yield of 1.37 mmol could be achieved in the overhead space. In addition, a dedicated reactor system for the anaerobic fermentation of T. neapolitana to produce H2 was developed. The bioreactor developed here can ferment anaerobically with a very low loss of produced gas. Here, after 24 h, a hydrogen concentration of 83% could be measured in the overhead space. KW - Biological hydrogen KW - Organic waste KW - Dark fermentation KW - Hydrolysis KW - Pretreatment Y1 - 2024 U6 - https://doi.org/10.3390/en17122938 SN - 1996-1073 N1 - Corresponding author: Nils Tippkötter VL - 17 IS - 12 PB - MDPI CY - Basel ER - TY - JOUR A1 - Block, Simon A1 - Viebahn, Peter A1 - Jungbluth, Christian T1 - Analysing direct air capture for enabling negative emissions in Germany: an assessment of the resource requirements and costs of a potential rollout in 2045 JF - Frontiers in Climate N2 - Direct air capture (DAC) combined with subsequent storage (DACCS) is discussed as one promising carbon dioxide removal option. The aim of this paper is to analyse and comparatively classify the resource consumption (land use, renewable energy and water) and costs of possible DAC implementation pathways for Germany. The paths are based on a selected, existing climate neutrality scenario that requires the removal of 20 Mt of carbon dioxide (CO2) per year by DACCS from 2045. The analysis focuses on the so-called “low-temperature” DAC process, which might be more advantageous for Germany than the “high-temperature” one. In four case studies, we examine potential sites in northern, central and southern Germany, thereby using the most suitable renewable energies for electricity and heat generation. We show that the deployment of DAC results in large-scale land use and high energy needs. The land use in the range of 167–353 km2 results mainly from the area required for renewable energy generation. The total electrical energy demand of 14.4 TWh per year, of which 46% is needed to operate heat pumps to supply the heat demand of the DAC process, corresponds to around 1.4% of Germany's envisaged electricity demand in 2045. 20 Mt of water are provided yearly, corresponding to 40% of the city of Cologne‘s water demand (1.1 million inhabitants). The capture of CO2 (DAC) incurs levelised costs of 125–138 EUR per tonne of CO2, whereby the provision of the required energy via photovoltaics in southern Germany represents the lowest value of the four case studies. This does not include the costs associated with balancing its volatility. Taking into account transporting the CO2 via pipeline to the port of Wilhelmshaven, followed by transporting and sequestering the CO2 in geological storage sites in the Norwegian North Sea (DACCS), the levelised costs increase to 161–176 EUR/tCO2. Due to the longer transport distances from southern and central Germany, a northern German site using wind turbines would be the most favourable. KW - rollout KW - economics KW - Germany KW - negative emissions KW - carbon dioxide removal KW - climate neutrality KW - DAC KW - direct air capture Y1 - 2024 U6 - https://doi.org/10.3389/fclim.2024.1353939 SN - 2624-9553 VL - 6 PB - Frontiers CY - Lausanne ER - TY - JOUR A1 - Biewendt, Marcel A1 - Blaschke, Florian A1 - Böhnert, Arno T1 - An evaluation of corporate sustainability in context of the Jevons paradox JF - SocioEconomic Challenges N2 - The successful implementation and continuous development of sustainable corporate-level solutions is a challenge. These are endeavours in which social, environmental, and financial aspects must be weighed against each other. They can prove difficult to handle and, in some cases, almost unrealistic. Concepts such as green controlling, IT, and manufacturing look promising and are constantly evolving. This paper aims to achieve a better understanding of the field of corporate sustainability (CS). It will evaluate the hypothesis by which Corporate Sustainability thrives, via being efficient, increasing the performance, and raising the value of the input of the enterprises to the resources used. In fact, Corporate Sustainability on the surface could seem to contradict the idea, which supports the understanding that it encourages the reduction of the heavy reliance on the use of natural resources, the overall environmental impact, and above all, their protection. To understand how the contradictory notion of CS came about, in this part of the paper, the emphasis is placed on providing useful insight to this regard. The first part of this paper summarizes various definitions, organizational theories, and measures used for CS and its derivatives like green controlling, IT, and manufacturing. Second, a case study is given that combines the aforementioned sustainability models. In addition to evaluating the hypothesis, the overarching objective of this paper is to demonstrate the use of green controlling, IT, and manufacturing in the corporate sector. Furthermore, this paper outlines the current challenges and possible directions for CS in the future. KW - rebound-effect KW - grey energy KW - efficiency side-effects KW - jevons paradox KW - corporate sustainability Y1 - 2020 U6 - https://doi.org/10.21272/sec.4(3).46-65.2020 SN - 2520-6214 VL - 4 IS - 3 SP - 46 EP - 65 PB - ARMG Publishing CY - Sumy ER - TY - JOUR A1 - Biewendt, Marcel A1 - Blaschke, Florian A1 - Böhnert, Arno T1 - The rebound effect – a systematic review of the current state of affairs JF - European Journal of Economics and Business Studies N2 - This publication is intended to present the current state of research on the rebound effect. First, a systematic literature review is carried out to outline (current) scientific models and theories. Research Question 1 follows with a mathematical introduction of the rebound effect, which shows the interdependence of consumer behaviour, technological progress, and interwoven effects for both. Thereupon, the research field is analysed for gaps and limitations by a systematic literature review. To ensure quantitative and qualitative results, a review protocol is used that integrates two different stages and covers all relevant publications released between 2000 and 2019. Accordingly, 392 publications were identified that deal with the rebound effect. These papers were reviewed to obtain relevant information on the two research questions. The literature review shows that research on the rebound effect is not yet comprehensive and focuses mainly on the effect itself rather than solutions to avoid it. Research Question 2 finds that the main gap, and thus the limitations, is that not much research has been published on the actual avoidance of the rebound effect yet. This is a major limitation for practical application by decision-makers and politicians. Therefore, a theoretical analysis was carried out to identify potential theories and ideas to avoid the rebound effect. The most obvious idea to solve this problem is the theory of a Steady-State Economy (SSE), which has been described and reviewed. KW - sustainability KW - rebound-effect KW - literature KW - systematic KW - critical KW - SSE) JEL : O33 KW - review Y1 - 2020 U6 - https://doi.org/10.26417/134nvy47z SN - 2601-8659 VL - 6 IS - 1 SP - 106 EP - 120 PB - Revistia CY - London ER - TY - JOUR A1 - Biewendt, Marcel A1 - Böhnert, Arno A1 - Blaschke, Florian T1 - The repercussions of the digital twin in the automotive industry on the new marketing logic JF - European Journal of Marketing and Economics N2 - Rapid development of virtual and data acquisition technology makes Digital Twin Technology (DT) one of the fundamental areas of research, while DT is one of the most promissory developments for the achievement of Industry 4.0. 48% percent of organisations implementing the Internet of Things are already using DT or plan to use DT in 2020. The global market for DT is expected to grow by 38 percent annually, reaching USD16 billion by 2023. In addition, the number of participating organisations using digital twins is expected to triple by 2022. DTs are characterised by the integration between physical and virtual spaces. The driving idea for DT is to develop, test and build our devices in a virtual environment. The objective of this paper is to study the impact of DT in the automotive industry on the new marketing logic. This paper outlines the current challenges and possible directions for the future DT in marketing. This paper will be helpful for managers in the industry to use the advantages and potentials of DT. KW - industry 4.0 KW - marketing KW - automotive KW - digital twin Y1 - 2020 U6 - https://doi.org/10.26417/229eim64f SN - 2601-8659 VL - 4 IS - 1 SP - 68 EP - 73 PB - Revistia CY - London ER - TY - JOUR A1 - Biewendt, Marcel T1 - Sustainable development: A quantitative analysis regarding the impact of resource rents on state welfare from 2002 to 2017 JF - SocioEconomic Challenges N2 - This paper uses a quantitative analysis to examine the interdependence and impact of resource rents on socio-economic development from 2002 to 2017. Nigeria and Norway have been chosen as reference countries due to their abundance of natural resources by similar economic performance, while the ranking in the Human Development Index differs dramatically. As the Human Development Index provides insight into a country’s cultural and socio-economic characteristics and development in addition to economic indicators, it allows a comparison of the two countries. The hypothesis presented and discussed in this paper was researched before. A qualitative research approach was used in the author’s master’s thesis “The Human Development Index (HDI) as a Reflection of Resource Abundance (using Nigeria and Norway as a case study)” in 2018. The management of scarce resources is an important aspect in the development of modern countries and those on the threshold of becoming industrialised nations. The effects of a mistaken resource management are not only of a purely economic nature but also of a social and socio-economic nature. In order to present a partial aspect of these dependencies and influences this paper uses a quantitative analysis to examine the interdependence and impact of resource rents on socio-economic development from 2002 to 2017. Nigeria and Norway have been chosen as reference countries due to their abundance of natural resources by similar economic performance, while the ranking in the Human Development Index differs significantly. As the Human Development Index provides insight into a country’s cultural and socio-economic characteristics and development in addition to economic indicators, it allows a comparison of the two countries. This paper found out in a holistic perspective that (not or poorly managed) resource wealth in itself has a negative impact on socio-economic development and significantly reduces the productivity of the citizens of a state. This is expressed in particular for the years 2002 till 2017 in a negative correlation of GDP per capita and HDI value with the share respectively the size of resources in the GDP of a country. KW - socio-economic welfare KW - resource abundance KW - sustainability KW - Human Development Index Y1 - 2020 U6 - https://doi.org/10.21272/sec.4(4).119-131.2020 SN - 2520-6214 VL - 4 IS - 4 SP - 119 EP - 131 PB - ARMG Publishing CY - Sumy ER - TY - JOUR A1 - Biewendt, Marcel A1 - Blaschke, Florian A1 - Böhnert, Arno T1 - A review of contemporary challenges in business culture JF - International Journal of Applied Research in Business and Management N2 - The following article deals with the basic principles of intercultural management and possible improvements in terms of cultural, ethnic and gender diversification. The results are exemplarily applied to a bank located in Germany. The aim of this paper is to find out to what extent intercultural management could improve the productivity of Relatos-Bank in dealing with foreign employees or employees with a different cultural background. To achieve this goal, the authors con-duct a literature research. The main sources of information are books, journal articles and internet sources. It becomes clear that especially the different perceptions of different generations have a potential for conflict, which can be counteracted by applying presented scientific models. Equalizing the salaries of female and male employees and equalizing the rights and distribution of power could also be the key to becoming an open-minded, dynamic and fair organization that is pre-pared for the rapidly changing environment in which it operates. Y1 - 2021 U6 - https://doi.org/10.51137/ijarbm.2021.2.1.1 SN - 2700-8983 VL - 2 IS - 1 SP - 1 EP - 12 PB - Wohllebe & Ross Publishing CY - Hamburg ER - TY - JOUR A1 - Biewendt, Marcel A1 - Blaschke, Florian A1 - Böhnert, Arno T1 - Motivational factors in organisational change JF - SocioEconomic Challenges N2 - The presented paper gives an overview of the most important and most common theories and concepts from the economic field of organisational change and is also enriched with quantitative publication data, which underlines the relevance of the topic. In particular, the topic presented is interwoven in an interdisciplinary way with economic psychological models, which are underpinned within the models with content from leading scholars in the field. The pace of change in companies is accelerating, as is technological change in our society. Adaptations of the corporate structure, but also of management techniques and tasks, are therefore indispensable. This includes not only the right approaches to employee motivation, but also the correct use of intrinsic and extrinsic motivational factors. Based on the hypothesis put forward by the scientist and researcher Rollinson in his book “Organisational behaviour and analysis” that managers believe motivational resources are available at all times, socio-economic and economic psychological theories are contrasted here in order to critically examine this statement. In addition, a fictitious company was created as a model for this work in order to illustrate the effects of motivational deficits in practice. In this context, the theories presented are applied to concrete problems within the model and conclusions are drawn about their influence and applicability. This led to the conclusion that motivation is a very individual challenge for each employee, which requires adapted and personalised approaches. On the other hand, the recommendations for action for supervisors in the case of motivation deficits also cannot be answered in a blanket manner, but can only be solved with the help of professional, expert-supported processing due to the economic-psychological realities of motivation. Identifying, analysing and remedying individual employee motivation deficits is, according to the authors, a problem and a challenge of great importance, especially in the context of rapidly changing ecosystems in modern companies, as motivation also influences other factors such as individual productivity. The authors therefore conclude that good motivation through the individual and customised promotion and further training of employees is an important point for achieving important corporate goals in order to remain competitive on the one hand and to create a productive and pleasant working environment on the other. KW - business culture KW - management KW - motivation KW - change Y1 - 2021 U6 - https://doi.org/10.21272/sec.5(3).15-27.2021 SN - 2520-6214 VL - 5 IS - 3 SP - 15 EP - 27 PB - ARMG CY - Sumy ER - TY - THES A1 - Pauls, Benjamin T1 - Energiewende im Stromsektor: Nachhaltigkeit über Umweltschutz hinaus BT - Qualitative Einblicke in den Energiewende-Diskurs des Stromsektors in Deutschland N2 - Die Energiewende wird häufig als „nachhaltig“ bezeichnet, das genaue Begriffsverständnis bleibt jedoch vage. Diese Transformation von fossilen und nuklearen hin zu erneuerbaren Energiequellen steht im Fokus der Treibhausgasneutralität. So soll dem fortschreitenden Klimawandel entgegengetreten werden. Das Thema der vorliegenden Arbeit ist die Definition eines möglichen Verständnisses von „Nachhaltigkeit“ in der Energiewende des deutschen Stromsektors. Die leitenden Forschungsfragen lauten: Was kann im Zusammenhang mit der Energiewende im Stromsektor Deutschlands unter Nachhaltigkeit verstanden werden? Inwieweit unterscheidet sich dieses Verständnis von der bisherigen Herangehensweise? Die Datenbasis zur Beantwortung dieser liefern sechs leitfadengestützte Expert:inneninterviews. Als Analysemethode dient die inhaltliche Strukturierung nach Mayring (2015). Die qualitative Studie hat gezeigt, dass eine nachhaltige Energiewende den Menschen und die Natur zentralisiert. Weiter aufgeschlüsselt stehen die drei Nachhaltigkeitsdimensionen und die Generationengerechtigkeit. Dabei dient die ökonomische Dimension der sozialen und ökologischen. Wichtig sind die Inklusion und Beteiligung von Bevölkerung, Unternehmen und Politik. Gleichzeitig ist sie Herausforderung und Chance für einen positiven gesellschaftlichen Wandel. Technisch dienen Windenergie- und Photovoltaikanlagen als Energielieferanten und Wasserstoffsysteme als Zwischenspeicher, Stabilitätssicherung und zur Kopplung der Sektoren. Damit ist Nachhaltigkeit die Chance, die Energiewende richtig zu gestalten und damit über Klimaneutralität hinauszugehen Y1 - 2024 ER - TY - JOUR A1 - Böhnert, Arno A1 - Blaschke, Florian A1 - Biewendt, Marcel T1 - Impact of sustainability on the strategic direction of luxury companies JF - European Journal of Marketing and Economics N2 - Today’s society is undergoing a paradigm shift driven by the megatrend of sustainability. This undeniably affects all areas of Western life. This paper aims to find out how the luxury industry is dealing with this change and what adjustments are made by the companies. For this purpose, interviews were conducted with managers from the luxury industry, in which they were asked about specific measures taken by their companies as well as trends in the industry. In a subsequent evaluation, the trends in the luxury industry were summarized for the areas of ecological, social, and economic sustainability. It was found that the area of environmental sustainability is significantly more focused than the other sub-areas. Furthermore, the need for a customer survey to validate the industry-based measures was identified. KW - Operations KW - Brands KW - Luxury KW - Change Y1 - 2022 SN - 2601-8659 VL - 6 IS - 1 SP - 70 EP - 85 PB - Revistia CY - London ER - TY - JOUR A1 - Thoma, Andreas A1 - Gardi, Alessandro A1 - Fisher, Alex A1 - Braun, Carsten T1 - Improving local path planning for UAV flight in challenging environments by refining cost function weights JF - CEAS Aeronautical Journal N2 - Unmanned Aerial Vehicles (UAV) constantly gain in versatility. However, more reliable path planning algorithms are required until full autonomous UAV operation is possible. This work investigates the algorithm 3DVFH* and analyses its dependency on its cost function weights in 2400 environments. The analysis shows that the 3DVFH* can find a suitable path in every environment. However, a particular type of environment requires a specific choice of cost function weights. For minimal failure, probability interdependencies between the weights of the cost function have to be considered. This dependency reduces the number of control parameters and simplifies the usage of the 3DVFH*. Weights for costs associated with vertical evasion (pitch cost) and vicinity to obstacles (obstacle cost) have the highest influence on the failure probability of the local path planner. Environments with mainly very tall buildings (like large American city centres) require a preference for horizontal avoidance manoeuvres (achieved with high pitch cost weights). In contrast, environments with medium-to-low buildings (like European city centres) benefit from vertical avoidance manoeuvres (achieved with low pitch cost weights). The cost of the vicinity to obstacles also plays an essential role and must be chosen adequately for the environment. Choosing these two weights ideal is sufficient to reduce the failure probability below 10%. KW - Bio-inspired systems KW - Path planning KW - Obstacle avoidance KW - Unmanned aerial vehicles Y1 - 2024 U6 - https://doi.org/10.1007/s13272-024-00741-x SN - 1869-5590 (eISSN) SN - 1869-5582 N1 - Corresponding author: Andreas Thoma PB - Springer CY - Wien ER - TY - JOUR A1 - Möhren, Felix A1 - Bergmann, Ole A1 - Janser, Frank A1 - Braun, Carsten T1 - Assessment of structural mechanical effects related to torsional deformations of propellers JF - CEAS Aeronautical Journal N2 - Lifting propellers are of increasing interest for Advanced Air Mobility. All propellers and rotors are initially twisted beams, showing significant extension–twist coupling and centrifugal twisting. Torsional deformations severely impact aerodynamic performance. This paper presents a novel approach to assess different reasons for torsional deformations. A reduced-order model runs large parameter sweeps with algebraic formulations and numerical solution procedures. Generic beams represent three different propeller types for General Aviation, Commercial Aviation, and Advanced Air Mobility. Simulations include solid and hollow cross-sections made of aluminum, steel, and carbon fiber-reinforced polymer. The investigation shows that centrifugal twisting moments depend on both the elastic and initial twist. The determination of the centrifugal twisting moment solely based on the initial twist suffers from errors exceeding 5% in some cases. The nonlinear parts of the torsional rigidity do not significantly impact the overall torsional rigidity for the investigated propeller types. The extension–twist coupling related to the initial and elastic twist in combination with tension forces significantly impacts the net cross-sectional torsional loads. While the increase in torsional stiffness due to initial twist contributes to the overall stiffness for General and Commercial Aviation propellers, its contribution to the lift propeller’s stiffness is limited. The paper closes with the presentation of approximations for each effect identified as significant. Numerical evaluations are necessary to determine each effect for inhomogeneous cross-sections made of anisotropic material. KW - Lifting propeller KW - Extension–twist coupling KW - Trapeze effect KW - Centrifugal twisting moment Y1 - 2024 U6 - https://doi.org/10.1007/s13272-024-00737-7 SN - 1869-5590 (eISSN) SN - 1869-5582 N1 - Corresponding author: Felix Möhren PB - Springer CY - Wien ER - TY - JOUR A1 - Adels, Klaudia A1 - Monakhova, Yulia T1 - Low-field NMR spectroscopic study of e-cigarettes: Is determination of only nicotine and organic carrier solvents possible? JF - Microchemical Journal N2 - Electronic cigarettes (e-cigarettes) have become popular worldwide with the market growing exponentially in some countries. The absence of product standards and safety regulations requires urgent development of analytical methodologies for the holistic control of the growing diversity of such products. An approach based on low-field nuclear magnetic resonance (LF-NMR) at 80 MHz is presented for the simultaneous determination of key parameters: carrier solvents (vegetable glycerine (VG), propylene glycol (PG) and water), total nicotine as well as free-base nicotine fraction. Moreover, qualitative and quantitative determination of fourteen weak organic acids deliberately added to enhance sensory characteristics of e-cigarettes was possible. In most cases these parameters can be rapidly and conveniently determined without using any sample manipulation such as dilution, extraction or derivatization steps. The method was applied for 37 authentic e-cigarettes samples. In particular, eight different organic acids with the content up to 56 mg/mL were detected. Due to its simplicity, the method can be used in routine regulatory control as well as to study release behaviour of nicotine and other e-cigarettes constituents in different products. KW - Electronic cigarettes KW - Low field NMR KW - Carrier solvents KW - Free-base nicotine KW - Weak organic acids Y1 - 2024 U6 - https://doi.org/10.1016/j.microc.2024.110859 SN - 1095-9149 N1 - Corresponding author: Yulia Monakhova VL - 203 PB - Elsevier CY - Amsterdam ER - TY - CHAP A1 - Schneider, Dominik A1 - Wisselink, Frank A1 - Czarnecki, Christian A1 - Nölle, Nikolai T1 - Benefits and framework conditions for information-driven business models concerning the Internet of Things T2 - Digitalization in companies N2 - In the context of the increasing digitalization, the Internet of Things (IoT) is seen as a technological driver through which completely new business models can emerge in the interaction of different players. Identified key players include traditional industrial companies, municipalities and telecommunications companies. The latter, by providing connectivity, ensure that small devices with tiny batteries can be connected almost anywhere and directly to the Internet. There are already many IoT use cases on the market that provide simplification for end users, such as Philips Hue Tap. In addition to business models based on connectivity, there is great potential for information-driven business models that can support or enhance existing business models. One example is the IoT use case Park and Joy, which uses sensors to connect parking spaces and inform drivers about available parking spaces in real time. Information-driven business models can be based on data generated in IoT use cases. For example, a telecommunications company can add value by deriving more decision-relevant information – called insights – from data that is used to increase decision agility. In addition, insights can be monetized. The monetization of insights can only be sustainable, if careful attention is taken and frameworks are considered. In this chapter, the concept of information-driven business models is explained and illustrated with the concrete use case Park and Joy. In addition, the benefits, risks and framework conditions are discussed. Y1 - 2024 SN - 978-3-658-39093-8 (Print) SN - 978-3-658-39094-5 (eBook) U6 - https://doi.org/10.1007/978-3-658-39094-5_5 SP - 59 EP - 75 PB - Springer CY - Wiesbaden ER - TY - RPRT A1 - Drescher, Hans Paul T1 - The irreversible thermodynamic’s theorem of minimum entropy production applied to the laminar and the turbulent Couette flow N2 - Analyzing thermodynamic non-equilibrium processes, like the laminar and turbulent fluid flow, the dissipation is a key parameter with a characteristic minimum condition. That is applied to characterize laminar and turbulent behaviour of the Couette flow, including its transition in both directions. The Couette flow is chosen as the only flow form with constant shear stress over the flow profile, being laminar, turbulent or both. The local dissipation defines quantitative and stable criteria for the transition and the existence of turbulence. There are basic results: The Navier Stokes equations cannot describe the experimental flow profiles of the turbulent Couette flow. But they are used to quantify the dissipation of turbulent fluctuation. The dissipation minimum requires turbulent structures reaching maximum macroscopic dimensions, describing turbulence as a “non-local” phenomenon. At the transition the Couette flow profiles and the shear stress change by a factor ≅ 5 due to a change of the “apparent” turbulent viscosity by a calculated factor ≅ 27. The resulting difference of the laminar and the turbulent profiles results in two different Reynolds numbers and different loci of transition, which are identified by calculation. KW - Turbulence KW - Transition KW - Minimum dissipation Y1 - 2018 ER - TY - RPRT A1 - Drescher, Hans Paul T1 - Turbulence - minimum dissipation and maximum macroscopic momentum exchange N2 - The minimum dissipation requirement of the thermodynamics of irreversible processes is applied to characterize the existence of laminar and non-laminar, and the co-existence of laminar and turbulent flow zones. Local limitations of the different zones and three different forms of transition are defined. For the Couette flow a non-local “corpuscular” flow mechanism explains the logarithmic law-of-the-wall, maximum turbulent dimensions and a value x=0,415 for the v. Kármán constant. Limitations of the logarithmic law near the wall and in the centre of the experiment are interpreted. Y1 - 2021 ER - TY - JOUR A1 - Stiemer, Luc Nicolas A1 - Thoma, Andreas A1 - Braun, Carsten T1 - MBT3D: Deep learning based multi-object tracker for bumblebee 3D flight path estimation JF - PLoS ONE N2 - This work presents the Multi-Bees-Tracker (MBT3D) algorithm, a Python framework implementing a deep association tracker for Tracking-By-Detection, to address the challenging task of tracking flight paths of bumblebees in a social group. While tracking algorithms for bumblebees exist, they often come with intensive restrictions, such as the need for sufficient lighting, high contrast between the animal and background, absence of occlusion, significant user input, etc. Tracking flight paths of bumblebees in a social group is challenging. They suddenly adjust movements and change their appearance during different wing beat states while exhibiting significant similarities in their individual appearance. The MBT3D tracker, developed in this research, is an adaptation of an existing ant tracking algorithm for bumblebee tracking. It incorporates an offline trained appearance descriptor along with a Kalman Filter for appearance and motion matching. Different detector architectures for upstream detections (You Only Look Once (YOLOv5), Faster Region Proposal Convolutional Neural Network (Faster R-CNN), and RetinaNet) are investigated in a comparative study to optimize performance. The detection models were trained on a dataset containing 11359 labeled bumblebee images. YOLOv5 reaches an Average Precision of AP = 53, 8%, Faster R-CNN achieves AP = 45, 3% and RetinaNet AP = 38, 4% on the bumblebee validation dataset, which consists of 1323 labeled bumblebee images. The tracker’s appearance model is trained on 144 samples. The tracker (with Faster R-CNN detections) reaches a Multiple Object Tracking Accuracy MOTA = 93, 5% and a Multiple Object Tracking Precision MOTP = 75, 6% on a validation dataset containing 2000 images, competing with state-of-the-art computer vision methods. The framework allows reliable tracking of different bumblebees in the same video stream with rarely occurring identity switches (IDS). MBT3D has much lower IDS than other commonly used algorithms, with one of the lowest false positive rates, competing with state-of-the-art animal tracking algorithms. The developed framework reconstructs the 3-dimensional (3D) flight paths of the bumblebees by triangulation. It also handles and compares two alternative stereo camera pairs if desired. Y1 - 2023 U6 - https://doi.org/10.1371/journal.pone.0291415 SN - 1932-6203 N1 - Corresponding author: Luc Nicolas Stiemer VL - 18 IS - 9 PB - PLOS CY - San Fancisco ER - TY - JOUR A1 - Karschuck, Tobias A1 - Poghossian, Arshak A1 - Ser, Joey A1 - Tsokolakyan, Astghik A1 - Achtsnicht, Stefan A1 - Wagner, Patrick A1 - Schöning, Michael Josef T1 - Capacitive model of enzyme-modified field-effect biosensors: Impact of enzyme coverage JF - Sensors and Actuators B: Chemical N2 - Electrolyte-insulator-semiconductor capacitors (EISCAP) belong to field-effect sensors having an attractive transducer architecture for constructing various biochemical sensors. In this study, a capacitive model of enzyme-modified EISCAPs has been developed and the impact of the surface coverage of immobilized enzymes on its capacitance-voltage and constant-capacitance characteristics was studied theoretically and experimentally. The used multicell arrangement enables a multiplexed electrochemical characterization of up to sixteen EISCAPs. Different enzyme coverages have been achieved by means of parallel electrical connection of bare and enzyme-covered single EISCAPs in diverse combinations. As predicted by the model, with increasing the enzyme coverage, both the shift of capacitance-voltage curves and the amplitude of the constant-capacitance signal increase, resulting in an enhancement of analyte sensitivity of the EISCAP biosensor. In addition, the capability of the multicell arrangement with multi-enzyme covered EISCAPs for sequentially detecting multianalytes (penicillin and urea) utilizing the enzymes penicillinase and urease has been experimentally demonstrated and discussed. KW - Field-effect biosensor KW - Capacitive model KW - Enzyme coverage KW - Multianalyte detection KW - Penicillin Y1 - 2024 U6 - https://doi.org/10.1016/j.snb.2024.135530 SN - 0925-4005 (Print) SN - 1873-3077 (Online) N1 - Corresponding Author: Michael J. Schöning VL - 408 PB - Elsevier CY - Amsterdam ER - TY - JOUR A1 - Turdumamatov, Samat A1 - Belda, Aljoscha A1 - Heuermann, Holger T1 - Shaping a decoupled atmospheric pressure microwave plasma with antenna structures, Maxwell’s equations, and boundary conditions JF - IEEE Transactions on Plasma Science N2 - This article addresses the need for an innovative technique in plasma shaping, utilizing antenna structures, Maxwell’s laws, and boundary conditions within a shielded environment. The motivation lies in exploring a novel approach to efficiently generate high-energy density plasma with potential applications across various fields. Implemented in an E01 circular cavity resonator, the proposed method involves the use of an impedance and field matching device with a coaxial connector and a specially optimized monopole antenna. This setup feeds a low-loss cavity resonator, resulting in a high-energy density air plasma with a surface temperature exceeding 3500 o C, achieved with a minimal power input of 80 W. The argon plasma, resembling the shape of a simple monopole antenna with modeled complex dielectric values, offers a more energy-efficient alternative compared to traditional, power-intensive plasma shaping methods. Simulations using a commercial electromagnetic (EM) solver validate the design’s effectiveness, while experimental validation underscores the method’s feasibility and practical implementation. Analyzing various parameters in an argon atmosphere, including hot S -parameters and plasma beam images, the results demonstrate the successful application of this technique, suggesting its potential in coating, furnace technology, fusion, and spectroscopy applications. KW - 3-D printing KW - Furnace KW - Fusion KW - Hot S-parameter KW - Mode converter Y1 - 2024 U6 - https://doi.org/10.1109/TPS.2024.3383589 SN - 0093-3813 (Print) SN - 1939-9375 (Online) IS - Early Access SP - 1 EP - 9 PB - IEEE ER - TY - JOUR A1 - Böhnisch, Nils A1 - Braun, Carsten A1 - Muscarello, Vincenzo A1 - Marzocca, Pier T1 - About the wing and whirl flutter of a slender wing–propeller system JF - Journal of Aircraft N2 - Next-generation aircraft designs often incorporate multiple large propellers attached along the wingspan (distributed electric propulsion), leading to highly flexible dynamic systems that can exhibit aeroelastic instabilities. This paper introduces a validated methodology to investigate the aeroelastic instabilities of wing–propeller systems and to understand the dynamic mechanism leading to wing and whirl flutter and transition from one to the other. Factors such as nacelle positions along the wing span and chord and its propulsion system mounting stiffness are considered. Additionally, preliminary design guidelines are proposed for flutter-free wing–propeller systems applicable to novel aircraft designs. The study demonstrates how the critical speed of the wing–propeller systems is influenced by the mounting stiffness and propeller position. Weak mounting stiffnesses result in whirl flutter, while hard mounting stiffnesses lead to wing flutter. For the latter, the position of the propeller along the wing span may change the wing mode shapes and thus the flutter mechanism. Propeller positions closer to the wing tip enhance stability, but pusher configurations are more critical due to the mass distribution behind the elastic axis. Y1 - 2024 U6 - https://doi.org/10.2514/1.C037542 SN - 1533-3868 SP - 1 EP - 14 PB - AIAA CY - Reston, Va. ER - TY - JOUR A1 - Schopp, Christoph A1 - Rohrbach, Felix A1 - Langer, Luc A1 - Heuermann, Holger T1 - Detection of welding wire length by active S11 measurement JF - IEEE Transactions on Plasma Science N2 - A novel method to determine the extruded length of a metallic wire for a directed energy deposition (DED) process using a microwave (MW) plasma jet with a straight-through wire feed is presented. The method is based on the relative comparison of the measured frequency response obtained by the large-signal scattering parameter (Hot-S) technique. In the practical working range, repeatability of less than 6% for a nonactive plasma and 9% for the active plasma state is found. Measurements are conducted with a focus on a simple solution to decrease the processing time and reduce the integration time of the process into the existing hardware. It is shown that monitoring a single frequency for magnitude and phase changes is sufficient to achieve good accuracy. A combination of different measurement values to determine the length is possible. The applicability to different diameter of the same material is shown as well as a contact detection of the wire and metallic substrate. KW - Circuit simulation KW - Hot S-parameter KW - Modeling KW - Plasma KW - Plasma diagnostics Y1 - 2024 U6 - https://doi.org/10.1109/TPS.2024.3356659 SN - 0093-3813 (Print) SN - 1939-9375 (Online) IS - Early Access SP - 1 EP - 6 PB - IEEE ER - TY - JOUR A1 - Pieronek, Lukas A1 - Kleefeld, Andreas T1 - On trajectories of complex-valued interior transmission eigenvalues JF - Inverse problems and imaging : IPI N2 - This paper investigates the interior transmission problem for homogeneous media via eigenvalue trajectories parameterized by the magnitude of the refractive index. In the case that the scatterer is the unit disk, we prove that there is a one-to-one correspondence between complex-valued interior transmission eigenvalue trajectories and Dirichlet eigenvalues of the Laplacian which turn out to be exactly the trajectorial limit points as the refractive index tends to infinity. For general simply-connected scatterers in two or three dimensions, a corresponding relation is still open, but further theoretical results and numerical studies indicate a similar connection. KW - Interior transmission problem KW - Eigenvalue trajectories KW - Complex-valued eigenvalues Y1 - 2024 U6 - https://doi.org/10.3934/ipi.2023041 SN - 1930-8337 (Print) SN - 1930-8345 (Online) VL - 18 IS - 2 SP - 480 EP - 516 PB - AIMS CY - Springfield, Mo ER - TY - JOUR T1 - Dimensionen Nr. 30 / 2023: Magazin der FH Aachen University of Applied Sciences - Der Mensch im Mittelpunkt N2 - 06| Warum es gemeinsam besser geht 10| Interview 14| Wer ist hier der Boss? 18| Schnittstelle zwischen Mensch und Technik 22| Zweite Heimat Jülich 28| Zwischen Angst und Hoffnung 32| Eine Sternstunde für die FH Aachen 36| Gegen alle Widerstände 38| Ein Ort, der bleibt 42| Der Aufblühende 46| Der Computer sitzt am Steuer 52| Da geht das Herz auf 54| Hoch hinaus 58| Beratungsangebote 60| Das alte Schätzchen T3 - Dimensionen - Magazin der FH Aachen University of Applied Sciences - 01/2023 Y1 - 2023 CY - Aachen ER - TY - THES A1 - Lambertus, Jan-Michael T1 - CardboardCastle N2 - „CardboardCastle“ ist ein 3D-Animationsfilm. Der Film zeigt die lebendig gewordene Welt zweier Königreiche aus Pappe, die in einem Streit um einen magischen Zauberstab verwickelt sind. Das Projekt beweist, dass es möglich ist, mit der Software „Blender“ einen vollwertigen und hochwertigen 3D-Animationsfilm zu erstellen. Dabei wurden alle Assets bis auf Texturen selbst hergestellt. Die virtuelle Pappe spielt hierbei eine fundamentale Rolle, für diese wurde ein vollkommen neuer Workflow entwickelt, welcher es ermöglicht, realistische Pappe zu visualisieren. „CardboardCastle“ setzt auf eine cinematische Inszenierung von Licht und vereint technisches Wissen mit unterhaltenden Inhalten. Dabei zeigt er die kindliche Vorstellungskraft und lädt die Zuschauer ein, sich an ihre eigenen kindlichen Fantasien zu erinnern. KW - 3D KW - Animation KW - Computergrafik KW - Blender Y1 - 2024 PB - FH Aachen CY - Aachen ER - TY - THES A1 - Frings, Christina T1 - Unerwünscht : Anti-Gestaltung im öffentlichen Raum N2 - »Unerwünscht« widmet sich einer Art von architektonischer Gestaltung, die auf tückische Weise als »defensive Architektur« bezeichnet wird. In Form einer Zeitung bietet sie einen umfassenden Einblick in das Thema und gewährt einen vielseitigen Blick in eine Thematik, die im Interesse der Verantwortlichen lieber im Verborgenen geblieben wäre. Defensive Architektur bezeichnet strategische Baumaßnahmen in der Stadt- und Bauplanung, die darauf abzielen, unerwünschte Personengruppen durch unpraktisches oder unbequemes Design von bestimmten Orten fernzuhalten. Diese Maßnahmen richten sich beispielsweise gegen obdachlose Menschen, Jugendliche oder Skateboarder*innen. Die überwiegende Mehrheit der Bevölkerung ist sich weder der Existenz von solchen architektonischen Maßnahmen noch ihrer Auswirkungen auf das Leben der Betroffenen bewusst. »Unerwünscht« zielt darauf ab, diese Lücke in der öffentlichen Wahrnehmung zu schließen. KW - Zeitung KW - Zeitungsdesign KW - Defensive Architektur KW - Feindliche Architektur KW - Anti-Obdachlosen Architektur Y1 - 2024 PB - FH Aachen CY - Aachen ER - TY - THES A1 - Jansen, Marie T1 - Budzi Budzi N2 - Mit über 1300 Büdchen in 86 Veedeln ist Köln Deutschlands Kiosk-Hauptstadt. Sie sind ein prägendes Element von Nachbarschaften und gehören zum Kölner Stadtbild einfach dazu wie der Dom und der Rhein. Durch Anekdoten, Interviews, Beiträge zur Popkultur, alte Fotografien, Momentaufnahmen und vertraute Grafiken sowie einer festen Formsprache entsteht das erste Büdchenmagazin für Köln. Das Periodikum erscheint alle drei Monate und liegt kostenfrei in den Büdchen aus. Es ist eine Publikation die beweist, dass Büdchen mehr als gängige Verkaufsstellen sind, sondern Knotenpunkte unserer Gesellschaft. KW - Kiosk KW - Magazin KW - Köln KW - Büdchen KW - Kultur Y1 - 2024 PB - FH Aachen CY - Aachen ER - TY - THES A1 - Liedtke, Janna T1 - Lehrmaterial für den Tiroler Skilehrerverband: Konzeption für eine crossmediale Neugestaltung N2 - Der Tiroler Skilehrerverband bereitet angehende Skilehrer:innen auf die verschiedenen Schneesportlehrer-Prüfungen vor. Skilehrer:innen spielen eine entscheidende Rolle im Erfolg des Wintertourismus, was ihre gesellschaftliche und wirtschaftliche Relevanz unterstreicht. Die zeitgemäße Neugestaltung des Lehrmaterials soll eine effektive Vermittlung von Lerninhalten ermöglichen. Durch die Kombination von Informationsdesign, Corporate Design und Editorial Design wird die Verständlichkeit und Attraktivität des Materials gesteigert. Die Integration einer Lernapp ermöglicht eine interaktive und multimediale Lernerfahrung sowie mehr Flexibilität für die Lernenden. Die crossmediale Neugestaltung wirkt den Problemen veralteter Darstellungsformen entgegen. Es wird deutlich, dass gut gestaltetes Lehrmaterial bei gleichbleibenden Inhalten zu einer besseren Lernerfahrung führt. KW - Lehrmaterial KW - Neugestaltung KW - Informationsdesign KW - Lernapp KW - Skilehrer Y1 - 2024 PB - FH Aachen CY - Aachen ER - TY - THES A1 - Fuchs, Simon T1 - CSTHEMAG : ein Magazin für die Streetwear-Community von CSTHELABEL N2 - In einer Welt, die von ständiger Vernetzung und sozialen Medien geprägt ist, gibt es eine spürbare Lücke für Menschen, die sich für die »Streetwear-Culture« interessieren. Viele junge Menschen, die von Fashion, Streetwear und der damit einhergehenden Kultur fasziniert sind, stoßen in ihrem direkten Umfeld oft auf Schwierigkeiten, Gleichgesinnte zu finden. CSTHELABEL hat es sich zur Aufgabe gemacht, die lebendige Streetwear-Community zu stärken und weiter zu fördern. CSTHEMAG ist ein Projekt, das in Kollaboration mit dem Gründer von CSTHELABEL entstanden ist. Es wurde eine Nullnummer für die erste Ausgabe des Magazins konzipiert, gestaltet und produziert. Diese beinhaltet Interviews mit Content-Creatorn aus der Community, jungen Modeschöpfer:innen sowie einen Einblick in vergangene Events und Pop-Ups. Das Magazin bietet Mitwirkenden und zukünftig Interessierten einen Raum in einem für das Label neuen Medium und schafft die Möglichkeit, ihre Stimmen zu stärken. CSTHEMAG verpflichtet sich gegenüber der lebendigen Community, eine eigene Plattform zu bieten, auf der ihre einzigartigen Talente, Geschichten und Inspirationen zum Ausdruck kommen. KW - Magazin KW - Streetwear Community KW - Soziale Medien KW - Fashion KW - Modeschöpfer Y1 - 2024 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER - TY - THES A1 - Heinemann, Katja T1 - 112 – Wenn Helfer Hilfe brauchen N2 - Der Rettungsdienst ist rund um die Uhr bei medizinischen Notfällen im Einsatz. Wie aber ist dieser organisiert? Was belastet die Mitarbeiter*innen im Berufsalltag? Und wie kann man die Rettungskräfte unterstützen? „112–WENN HELFER HILFE BRAUCHEN“ bietet einen sachlichen Einblick in die Welt des Rettungsdienstes und der Ersten Hilfe. Mit kurz gefassten Fakten und Illustrationen richtet sich das Projekt vor allem an Jugendliche und junge Erwachsene. Ziel ist es, mehr Verständnis und Wertschätzung in der Gesellschaft für diese Berufsgruppe zu schaffen. Zusätzlich soll es die Leser*innen ermutigen, im Ernstfall angemessen zu handeln und „Leben zu retten“. Denn jeder kann in eine Notsituation geraten und auf den Rettungsdienst und Erste Hilfe angewiesen sein. Je früher man sich mit der Thematik beschäftigt, desto besser ist man im Ernstfall vorbereitet. KW - Rettungsdiesnt KW - Erste Hilfe KW - Notfall KW - Notruf KW - Rettungsdienst unterstützen Y1 - 2024 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER - TY - THES A1 - Jung, Maximilian T1 - Out of the Box : Cardistry Dokumentarfilm N2 - "Out of the Box" ist ein Dokumentarfilm und bietet einen Einblick in die Welt des "Cardistry". Der Schwerpunkt liegt auf dieser Nischenkunst und -kultur der visuell ansprechenden Kartenmanipulation. Der Film beleuchtet den Beginn, die Entwicklung und die lebendige Gemeinschaft hinter dieser einzigartigen Kunstform. Darüber hinaus werden Abgrenzungen, Ursprünge und Ähnlichkeiten zur Kartenmagie erforscht. KW - Cardistry KW - Karten KW - Magie KW - Dokumentarfilm Y1 - 2024 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER - TY - THES A1 - Kordes, Franka T1 - Invisible Cities N2 - Diese Arbeit präsentiert eine Neuinterpretation des Romans "Invisible Cities" von Italo Calvino in einem handgefertigten, künstlerischen Buchobjekt. Seit der Erstveröffentlichung des italienischen Literaturklassikers orientieren sich jegliche Neuauflagen an der Originalfassung. Die klassisch gestaltete Urversion wird der komplexen und eindrucksvollen Geschichte nicht mehr gerecht. Die Erzählung findet auf mehreren Ebenen statt, die durch verschiedene Papiersorten repräsentiert werden. Die Lesenden wissen somit immer, wo sie sich auf ihrer Reise durch die traumhaften und surrealen Städte befinden. Das Buch enthält mehrere Illustrationen auf Transparentpapierbögen, welche die Stadtbeschreibungen begleiten. Der besondere Fokus der Arbeit lag in den Illustrationen und der technischen und handwerklichen Umsetzung der Bindung. KW - Italo Calvino KW - Literaturklassiker KW - Buchbindekunst KW - Linoldruck KW - Transparentpapier Y1 - 2024 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER - TY - JOUR A1 - Yoshinobu, Tatsuo A1 - Miyamoto, Ko-ichiro A1 - Wagner, Torsten A1 - Schöning, Michael Josef T1 - Field-effect sensors combined with the scanned light pulse technique: from artificial olfactory images to chemical imaging technologies JF - Chemosensors N2 - The artificial olfactory image was proposed by Lundström et al. in 1991 as a new strategy for an electronic nose system which generated a two-dimensional mapping to be interpreted as a fingerprint of the detected gas species. The potential distribution generated by the catalytic metals integrated into a semiconductor field-effect structure was read as a photocurrent signal generated by scanning light pulses. The impact of the proposed technology spread beyond gas sensing, inspiring the development of various imaging modalities based on the light addressing of field-effect structures to obtain spatial maps of pH distribution, ions, molecules, and impedance, and these modalities have been applied in both biological and non-biological systems. These light-addressing technologies have been further developed to realize the position control of a faradaic current on the electrode surface for localized electrochemical reactions and amperometric measurements, as well as the actuation of liquids in microfluidic devices. KW - visualization KW - light-addressing technologies KW - scanned light pulse technique KW - field-effect structure KW - MOS KW - metal-oxide-semiconductor structure KW - catalytic metal KW - electronic nose KW - gas sensor KW - artificial olfactory image Y1 - 2024 U6 - https://doi.org/10.3390/chemosensors12020020 SN - 2227-9040 N1 - This article belongs to the Special Issue "An Exciting Journey of Chemical Sensors and Biosensors: A Theme Issue in Honor of Professor Ingemar Lundström" Corresponding author: Tatsuo Yoshinobu, Michael J. Schöning VL - 12 IS - 2 PB - MDPI CY - Basel ER - TY - THES A1 - Eichler, Sophie T1 - Digitales Arztpraxis Management N2 - Das Ziel der digitalen Arztpraxis-Management-App „PraXma“ ist es, die Organisation von Arztpraxen, sowie auch das Patient:innen- und Terminmanagement einer Praxis effizienter und reibungsloser zu gestalten. Da 83 Prozent der Patient:innen bei der Digitalisierung des deutschen Gesundheitswesens Nachholbedarf sehen, besteht ein erheblicher Bedarf an Weiterentwicklung in dieser Branche. „PraXma“ gewährleistet Patient:innen mithilfe verschiedener Funktionen einen angenehmeren Arztbesuch. Dazu zählen die patientenorientierte Terminvergabe, der kategorisierte Überblick über Vitalwerte und Pässe und die Einsicht in persönliche Dokumente, wie Befunde, Rezepte und mehr. Auch Ärzt:innen profitieren durch „PraXma“ von einer Automatisierung ihrer alltäglichen Abläufe und minimieren so Überstunden und Stress. KW - Arztpraxis KW - Terminmanagement KW - Effizienzsteigerung KW - Organisation KW - Digitalisierung Y1 - 2024 PB - FH Aachen CY - Aachen ER - TY - THES A1 - Darboven, Mona T1 - Gamifizierte Online-Schulung zur IT-Sicherheit : Konzeption & Gestaltung verschiedener Ansätze N2 - Das Ziel der webbasierten, gamifizierten Schulung ist die Awareness der IT-Sicherheit für Studierende. Das Verhalten der Studierenden soll nachhaltig geändert werden, damit zukünftige Cyberangriffe weniger wirksam werden. Im Mittelpunkt steht ein spannendes und motivierendes Konzept auf den Grundlagen des Game Based Learnings, das z. B. mit Interactives arbeitet. Zur Stärkung des Risiko-Bewusstseins wurde eine Roadmap entwickelt, die wie ein Spielbrett Zusammenhänge, aber auch den Fortschritt der Schulung aufzeigt. So entstand zunächst in interdisziplinärer Zusammenarbeit mit einer Wirtschaftsinformatik-Studentin ein technischer Prototyp. Darauf aufbauend wurden weitere konzeptionelle und visuelle Ansätze entwickelt, die das breite Spektrum von Game Based Learning zeigen. Dieses realitätsnahe Projekt zeigt zukunftsweisende Lernumgebungen auf. KW - Game Based Learning KW - Gamification KW - Serious Games KW - IT-Sicherheit KW - Webbasierte Schulung Y1 - 2024 PB - FH Aachen CY - Aachen ER - TY - THES A1 - Breuer, Annika T1 - Climate Engineering : Entwicklung einer digitalen Plattform für Geoengineering-Methoden und Klimawandel-Daten N2 - Dieses Projekt hat zum Ziel, umfassend über Climate Engineering-Maßnahmen zu informieren und dabei insbesondere ihre Funktionsweise, Kosten und Risiken darzustellen. Die entstandene Plattform "Die Erde abkühlen!" bietet einen Einblick in die Lösungsansätze des Climate Engineerings durch die Verwendung von Storytelling. Sie ermöglicht Nutzer:innen einen Überblick über den aktuellen Stand der Klimaerwärmung sowie den Vergleich von Climate Engineering-Maßnahmen. Ein entwickeltes Bewertungssystem auf Grundlage der "Royal Society" sowie interaktive Infografiken geben Nutzer:innen einen umfassenden Einblick. Das Hauptziel des Projekts ist die digitale Transformation der Climate Engineering-Lösungsansätze. Dabei geht es nicht nur darum, über die Folgen der Klimaerwärmung zu informieren, sondern auch konkrete Lösungen aufzuzeigen. Durch die Entwicklung eines innovativen Storytellings wird die Thematik nicht nur dramaturgisch präsentiert, sondern ermöglicht es den Nutzer:innen auch, ihre eigene Wissensvertiefung zu steuern. KW - Climate Engineering KW - Klimawandel Y1 - 2024 PB - FH Aachen CY - Aachen ER - TY - THES A1 - Dankelmann, Florian T1 - Almanya : kulinarische Brücken und Soziale Bindungen der türkischen Diaspora in Deutschland N2 - Die fotografische Arbeit "Almanya" veranschaulicht Teilaspekte der türkischen Kultur anhand von Repräsentantinnen und Repräsentanten der türkeistämmigen Community in Deutschland. Mit einem Fokus auf Kulinarik und Formen des Zusammenlebens werden Menschen mit türkischen Wurzeln porträtiert, sodass am Ende ein Einblick in deren Lebens- und Gedankenwelt ermöglicht wird und kulinarische Brücken zwischen Deutschen und der türkischen Kultur gebaut werden. Die enthaltene Botschaft, welche das Projekt den Rezipient:innen überbringt, ist in einem multikulturellen Land wie Deutschland von großer Wichtigkeit für gegenseitiges Verständnis und bildet den Boden für ein harmonisches Miteinander. KW - Fotografie KW - Kultur KW - Türkei KW - Deutschland KW - Essen Y1 - 2024 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER - TY - THES A1 - Berwanger, Natalie T1 - Social Media Kampagne – Produktwerbung : Videobegleitende Social Media Kampagne zur Vermarktung eines Produkts N2 - Diese zweiwöchige Social Media Kampagne präsentiert ein Auto durch eine Fusion von realer und digitaler Kunst, unterstützt von audiovisuellen Elementen. Ziel ist es, ein neues Erlebnis zu schaffen, das nachhaltige Mobilität in städtischer Kultur reflektiert und fortschrittliche Technologien nutzt. KW - Innovation KW - Nachhaltigkeit KW - Urbanität KW - Digital Artistry KW - Emotional Resonance Y1 - 2024 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER - TY - CHAP A1 - Ulke, Bernd ED - Krause, Thomas ED - Ulke, Bernd ED - Ferger, Martin T1 - Privates Baurecht und Nachtragsmanagement T2 - Zahlentafeln für den Baubetrieb N2 - Kein Bauvorhaben sollte realisiert werden, ohne dass es auf einer vertraglichen Grundlage zwischen Auftraggeber und Auftragnehmer fußt. Diese vertragliche Grundlage zu kennen ist essenziell, um dementsprechend handeln zu können. Denn nur wer seine eigenen Rechte und auch Pflichten kennt, kann sich auf diese berufen. Y1 - 2024 SN - 978-3-658-41329-3 (Print) SN - 978-3-658-41330-9 (eBook) U6 - https://doi.org/10.1007/978-3-658-41330-9_3 SP - 149 EP - 216 PB - Springer Vieweg CY - Wiesbaden ER - TY - CHAP A1 - Krause, Thomas ED - Krause, Thomas ED - Ulke, Bernd ED - Ferger, Martin T1 - Baumaschinen T2 - Zahlentafeln für den Baubetrieb N2 - Die Leistungsermittlung und Bemessung von Baumaschinen für die folgenden Bereiche werden bearbeitet: Maschinen für den Betonbau, Hebezeuge, Maschinen für den Erdbau, Straßenbaumaschinen, Rückbaugeräte und Elemente der Baustelleneinrichtung. Y1 - 2024 SN - 978-3-658-41329-3 (Print) SN - 978-3-658-41330-9 (eBook) U6 - https://doi.org/10.1007/978-3-658-41330-9_8 SP - 399 EP - 498 PB - Springer Vieweg CY - Wiesbaden ER - TY - BOOK A1 - Laumann, Jörg A1 - Wolf, Christian T1 - Stahlbau 1 : Bemessung von Stahlbauten nach Eurocode mit zahlreichen Beispielen Y1 - 2024 SN - 978-3-658-41323-1 (Print) SN - 978-3-658-41324-8 (eBook) U6 - https://doi.org/10.1007/978-3-658-41324-8 PB - Springer Vieweg CY - Wiesbaden ET - 26., überarbeitete und aktualisierte Auflage ER - TY - CHAP A1 - Melzner, Jürgen A1 - Ferger, Martin ED - Krause, Thomas ED - Ulke, Bernd ED - Ferger, Martin T1 - Building Information Modeling T2 - Zahlentafeln für den Baubetrieb N2 - Durch die Einführung von Building Information Modeling (BIM) sowohl projektspezifisch als auch in ganze Unternehmungen hat die Baubranche einen weitreichenden Veränderungsprozess angestoßen. Building Information Modeling kann als eine Methode angesehen werden, um die Informationsasymmetrien zwischen den Projektbeteiligten so gering wie möglich zu halten. Y1 - 2024 SN - 978-3-658-41329-3 (Print) SN - 978-3-658-41330-9 (eBook) U6 - https://doi.org/10.1007/978-3-658-41330-9_15 SP - 1051 EP - 1073 PB - Springer Vieweg CY - Wiesbaden ER - TY - CHAP A1 - Ulke, Bernd ED - Krause, Thomas ED - Ulke, Bernd ED - Ferger, Martin T1 - Kalkulation T2 - Zahlentafeln für den Baubetrieb N2 - Das Kapitel behandelt die Kosten- und Preisermittlung, die Kostenvorgabe und Kostenkontrolle. Der Angebotspreis wird aufgeschlüsselt in die Einzelkosten der Teilleistungen, die Baustellengemeinkosten, die Allgemeinen Geschäftskosten und einen Zuschlag für Wagnis und Gewinn. Auf der Basis der Angebotskalkulation werden die Vorgaben für die Kostenkontrolle entwickelt. Y1 - 2024 SN - 978-3-658-41329-3 (Print) SN - 978-3-658-41330-9 (eBook) U6 - https://doi.org/10.1007/978-3-658-41330-9_12 SP - 801 EP - 909 PB - Springer Vieweg CY - Wiesbaden ER - TY - CHAP A1 - Krause, Thomas ED - Krause, Thomas ED - Ulke, Bernd ED - Ferger, Martin T1 - Schalung und Gerüste T2 - Zahlentafeln für den Baubetrieb N2 - Systemschalungen und Systemgerüste haben den Baustellenbetrieb in vielen Bereichen sehr vereinfacht. Dennoch sind Kenntnisse in diesen Feldern für eine erfolgreiche und effektive Bauleitung unverzichtbar. In diesem Kapitel werden Hinweise und Empfehlungen für die Bemessung und Einsatz von Schalungen, Trag- und Arbeitsgerüsten für den Baustellenbetrieb gegeben. Y1 - 2024 SN - 978-3-658-41329-3 (Print) SN - 978-3-658-41330-9 (eBook) U6 - https://doi.org/10.1007/978-3-658-41330-9_10 SP - 659 EP - 705 PB - Springer Vieweg CY - Wiesbaden ER - TY - CHAP A1 - Ulke, Bernd ED - Krause, Thomas ED - Ulke, Bernd ED - Ferger, Martin T1 - Boden, Baugrube, Verbau T2 - Zahlentafeln für den Baubetrieb N2 - Die Lösung den Baugrund betreffender Fragestellungen beginnen i. d. R. mit der Durchführung von Baugrunderkundungen, um alle notwendigen Parameter zu erhalten, die für die Planung und Durchführung von Bauvorhaben notwendig sind. Im Folgenden werden die wichtigsten Erkundungen in Abhängigkeit der erforderlichen Güteklasse der Proben beschrieben und vorgestellt. Y1 - 2024 SN - 978-3-658-41329-3 (Print) SN - 978-3-658-41330-9 (eBook) U6 - https://doi.org/10.1007/978-3-658-41330-9_9 SP - 499 EP - 658 PB - Springer Vieweg CY - Wiesbaden ER - TY - CHAP A1 - Krause, Thomas A1 - Ulke, Bernd ED - Krause, Thomas ED - Ulke, Bernd ED - Ferger, Martin T1 - Bauabrechnung und Mengenermittlung T2 - Zahlentafeln für den Baubetrieb N2 - n diesem Kapitel werden die Abrechnungsvorschriften wichtiger ATV kurz, aber umfassend zusammengestellt. Einigen Abrechnungsbestimmungen für Einzelleistungen, die keine Nebenleistungen sind ((siehe DIN 18299 und Abschnitt 4 der jeweiligen ATV), sind mit aufgenommen worden; die ATV enthalten jedoch weitergehende Festlegungen über Nebenleistungen und Besondere Leistungen. Im Anschluss folgen Hinweise zu den Toleranzen im Hochbau sowie im Straßenbau. Y1 - 2024 SN - 978-3-658-41329-3 (Print) SN - 978-3-658-41330-9 (eBook) U6 - https://doi.org/10.1007/978-3-658-41330-9_7 SP - 333 EP - 397 PB - Springer Vieweg CY - Wiesbaden ER - TY - CHAP A1 - Ferger, Martin ED - Krause, Thomas ED - Ulke, Bernd ED - Ferger, Martin T1 - Arbeitsvorbereitung und Ablaufplanung T2 - Zahlentafeln für den Baubetrieb N2 - Die Arbeitsvorbereitung, als ein wesentliches Aufgabengebiet des Baubetriebswesens, ist von enormer Bedeutung für den Erfolg eines Bauprojektes. Die Arbeitsvorbereitung lässt sich zeitlich sowohl in der Angebotsphase (kalkulationsbegleitende Arbeitsvorbereitung), in der Vorbereitungsphase der Baustelle (von Auftragsvergabe bis Baubeginn) als auch baubegleitend einordnen. Y1 - 2024 SN - 978-3-658-41329-3 (Print) SN - 978-3-658-41330-9 (eBook) U6 - https://doi.org/10.1007/978-3-658-41330-9_6 SP - 299 EP - 332 PB - Springer Vieweg CY - Wiesbaden ER - TY - CHAP A1 - Ulke, Bernd ED - Krause, Thomas ED - Ulke, Bernd ED - Ferger, Martin T1 - Öffentliches Baurecht, Ausschreibung und Vergabe T2 - Zahlentafeln für den Baubetrieb N2 - Durch das öffentliche Baurecht werden die Zulässigkeit, die Grenzen, die Ordnung und die Förderung der baulichen Nutzung des Bodens geregelt. Die Ausschreibung und die Vergabe sind von essenzieller Bedeutung für ein Bauvorhaben und werden deshalb in der HOAI mit zwei Leistungsphasen abgebildet: nämlich mit der Leistungsphase 6 Vorbereitung der Vergabe sowie der Leistungsphase 7 Mitwirkung bei der Vergabe. Im Zuge der Ausschreibung und der Vergabe werden die für den AG anfallenden Kosten festgelegt und bilden somit die letzte größere Stellschraube für Preiseinsparungen. Y1 - 2024 SN - 978-3-658-41329-3 (Print) SN - 978-3-658-41330-9 (eBook) U6 - https://doi.org/10.1007/978-3-658-41330-9_5 SP - 263 EP - 297 PB - Springer Vieweg CY - Wiesbaden ER - TY - CHAP A1 - Ulke, Bernd ED - Krause, Thomas ED - Ulke, Bernd ED - Ferger, Martin T1 - Bauwirtschaft T2 - Zahlentafeln für den Baubetrieb N2 - Die Leistungen der Bauwirtschaft und deren wirtschaftliche Bedeutung in Deutschland werden anhand einer Vielzahl statistischer Daten verdeutlicht. Die im Vergleich zu anderen Wirtschaftsbereichen auftretenden branchenspezifischen Besonderheiten der Bauwirtschaft werden anhand von verschiedenen Kriterien herausgearbeitet. Das Zusammenspiel der einzelnen Akteure des Sektors und die dabei sich ergebenden bzw. zu beachtenden Rechts- und Vertragsgrundlagen werden dargestellt. Aufgrund der meist erheblichen Höhe des eingesetzten Kapitals werden auch notwendige Formen der Risikoabsicherungen und der in der Branche üblichen und teilweise vorgeschriebenen Versicherungsmöglichkeiten angesprochen. Y1 - 2024 SN - 978-3-658-41329-3 (Print) SN - 978-3-658-41330-9 (eBook) U6 - https://doi.org/10.1007/978-3-658-41330-9_4 SP - 17 EP - 261 PB - Springer Vieweg CY - Wiesbaden ER - TY - CHAP A1 - Ricker, Marcus A1 - Ulke, Bernd ED - Krause, Thomas ED - Ulke, Bernd ED - Ferger, Martin T1 - Baustoffe T2 - Zahlentafeln für den Baubetrieb N2 - In diesem Kapitel werden die Eigenschaften der Baustoffe Bitumen, Beton und Mauerwerk insbesondere unter dem Aspekt der Anwendung im Baustellenbetrieb dargestellt. Y1 - 2024 SN - 978-3-658-41329-3 (Print) SN - 978-3-658-41330-9 (eBook) U6 - https://doi.org/10.1007/978-3-658-41330-9_2 SP - 61 EP - 148 PB - Springer Vieweg CY - Wiesbaden ER - TY - BOOK A1 - Krause, Thomas A1 - Ulke, Bernd A1 - Ferger, Martin ED - Krause, Thomas ED - Ulke, Bernd ED - Ferger, Martin T1 - Zahlentafeln für den Baubetrieb Y1 - 2024 SN - 978-3-658-41329-3 (Print) SN - 978-3-658-41330-9 (eBook) U6 - https://doi.org/10.1007/978-3-658-41330-9 PB - Springer Vieweg CY - Wiesbaden ET - 10. Auflage ER - TY - JOUR A1 - Pogorelova, Natalia A1 - Rogachev, Evgeniy A1 - Akimbekov, Nuraly S. A1 - Digel, Ilya T1 - Effect of dehydration method on the micro- and nanomorphological properties of bacterial cellulose produced by Medusomyces gisevii on different substrates JF - Journal of materials science N2 - Many important properties of bacterial cellulose (BC), such as moisture absorption capacity, elasticity and tensile strength, largely depend on its structure. This paper presents a study on the effect of the drying method on BC films produced by Medusomyces gisevii using two different procedures: room temperature drying (RT, (24 ± 2 °C, humidity 65 ± 1%, dried until a constant weight was reached) and freeze-drying (FD, treated at − 75 °C for 48 h). BC was synthesized using one of two different carbon sources—either glucose or sucrose. Structural differences in the obtained BC films were evaluated using atomic force microscopy (AFM), scanning electron microscopy (SEM), and X-ray diffraction. Macroscopically, the RT samples appeared semi-transparent and smooth, whereas the FD group exhibited an opaque white color and sponge-like structure. SEM examination showed denser packing of fibrils in FD samples while RT-samples displayed smaller average fiber diameter, lower surface roughness and less porosity. AFM confirmed the SEM observations and showed that the FD material exhibited a more branched structure and a higher surface roughness. The samples cultivated in a glucose-containing nutrient medium, generally displayed a straight and ordered shape of fibrils compared to the sucrose-derived BC, characterized by a rougher and wavier structure. The BC films dried under different conditions showed distinctly different crystallinity degrees, whereas the carbon source in the culture medium was found to have a relatively small effect on the BC crystallinity. Y1 - 2024 U6 - https://doi.org/10.1007/s10853-024-09596-3 SN - 1573-4803 (Online) SN - 0022-2461 (Print) N1 - Corresponding author: Ilya Digel VL - 2024 PB - Springer Science + Business Media CY - Dordrecht ER - TY - JOUR A1 - Bertz, Morten A1 - Schöning, Michael Josef A1 - Molinnus, Denise A1 - Homma, Takayuki T1 - Influence of temperature, light, and H₂O₂ concentration on microbial spore inactivation: in-situ Raman spectroscopy combined with optical trapping JF - Physica status solidi (a) applications and materials science N2 - To gain insight on chemical sterilization processes, the influence of temperature (up to 70 °C), intense green light, and hydrogen peroxide (H₂O₂) concentration (up to 30% in aqueous solution) on microbial spore inactivation is evaluated by in-situ Raman spectroscopy with an optical trap. Bacillus atrophaeus is utilized as a model organism. Individual spores are isolated and their chemical makeup is monitored under dynamically changing conditions (temperature, light, and H₂O₂ concentration) to mimic industrially relevant process parameters for sterilization in the field of aseptic food processing. While isolated spores in water are highly stable, even at elevated temperatures of 70 °C, exposure to H₂O₂ leads to a loss of spore integrity characterized by the release of the key spore biomarker dipicolinic acid (DPA) in a concentration-dependent manner, which indicates damage to the inner membrane of the spore. Intensive light or heat, both of which accelerate the decomposition of H₂O₂ into reactive oxygen species (ROS), drastically shorten the spore lifetime, suggesting the formation of ROS as a rate-limiting step during sterilization. It is concluded that Raman spectroscopy can deliver mechanistic insight into the mode of action of H₂O₂-based sterilization and reveal the individual contributions of different sterilization methods acting in tandem. KW - hydrogen peroxide KW - optical spore trapping KW - Raman spectroscopy KW - sterilization conditions KW - temperature Y1 - 2024 U6 - https://doi.org/10.1002/pssa.202300866 SN - 1862-6319 (Online) SN - 1862-6300 (Print) N1 - Corresponding author: Michael J. Schöning IS - Early View PB - Wiley-VCH CY - Berlin ER - TY - THES A1 - Albrecht, Dustin T1 - „ARRK Journeys“ Filmformat-Konzept N2 - Das Projekt "ARRK Journeys" entwickelt ein neues Dokumentarfilm-Format, das darauf abzielt, potenzielle Mitarbeiter für die ARRK Engineering GmbH zu gewinnen Das Ziel des Projekts ist es, die Vielfalt an Karrieremöglichkeiten bei der ARRK Engineering GmbH aufzuzeigen und die Attraktivität des Unternehmens als Arbeitgeber zu betonen. Durch individuelle Mitarbeitergeschichten werden die Fragen beantwortet, warum eine berufliche Laufbahn bei ARRK erstrebenswert ist, ob jeder die Möglichkeit hat, bei ARRK zu arbeiten, und welche Entwicklungsmöglichkeiten das Unternehmen bietet. "ARRK Journeys" betont das Wohlbefinden der Mitarbeiter und ihre persönliche Bindung zum Unternehmen, um eine positive Arbeitgebermarke zu schaffen. "ARRK Journeys" präsentiert die ARRK Engineering GmbH als attraktiven Arbeitgeber und inspiriert potenzielle Mitarbeiter dazu, ihren eigenen Weg zu finden. KW - Employer Branding KW - Filmkonzept KW - Marketing KW - Film KW - Dokumentarfilm Y1 - 2024 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER - TY - THES A1 - Erkens, Cedric T1 - En(Joy)Chroma : Entwicklung einer medienübergreifenden Werbekampagne für den Brillenhersteller EnChroma N2 - Weltweit sind 350 Millionen Menschen von Farbenfehlsichtigkeit betroffen, doch nur wenige wissen, dass es eine Lösung für genau dieses Problem gibt. Die ausgearbeitete Werbekampagne und neue Markenkommunikation für EnChroma soll genau diese Menschen ermutigen, sich mit ihrer Krankheit auseinanderzusetzen und das breite Konzept der Lösung zu verstehen. Die speziellen Brillen ermöglichen es den Menschen, Farben im Alltag und Berufsleben in echt wahrzunehmen und diese besser differenzieren zu können. Unsere Welt ist farbcodiert und deshalb ist es besonders wichtig, dass diese Menschen auf das Produkt aufmerksam gemacht werden. KW - Farben KW - Farbenblind KW - Rot-Grün-Sehschwäche KW - Brillen KW - EnChroma Y1 - 2024 PB - FH Aachen CY - Aachen ER - TY - THES A1 - Fleischer, Rebekka T1 - Bringing brand experience to marketplaces : ein Online-Marktplatz, der Konsument und Marke verbindet N2 - «Keno» zeigt ein Konzept für einen Online-Marktplatz im Fashion-Segment, mit Fokus auf individueller Beratung, digitaler Anprobe und visueller sowie informativer Präsentation der Marken. Marktplätze werden aufgrund von großer Auswahl und Vertrauenswürdigkeit von Konsument:innen bevorzugt aufgesucht. Durch die immersive Darstellung an einem maßgetreuen Avatar und die Einbindung der Marke in das Einkaufserlebnis soll hier die Zahl der Retouren verringert und die Kund:innenzufriedenheit gesteigert werden. Mittels nutzerorientierter Strategien und der Gestaltung eines Designsystems bekam «Keno» seinen Look. Dabei fanden modernste Techniken wie künstliche Intelligenzen und Design Token Systeme Verwendung. Das Projekt zeigt letztendlich Möglichkeiten auf, wie ein Marktplatz durch Brand Experience, Onlineshopping-Wege verkürzen und zu mehr Nachhaltigkeit im E-Commerce beitragen kann. KW - E-Commerce KW - Online-Marktplatz KW - Fashion KW - Markenerlebnis KW - Avatar-Anprobe Y1 - 2024 PB - FH Aachen CY - Aachen ER - TY - JOUR A1 - Hafidi, Youssef A1 - El Hatka, Hicham A1 - Schmitz, Dominik A1 - Krauss, Manuel A1 - Pettrak, Jürgen A1 - Biel, Markus A1 - Ittobane, Najim T1 - Sustainable soil additives for water and micronutrient supply: swelling and chelating properties of polyaspartic acid hydrogels utilizing newly developed crosslinkers JF - Gels N2 - Drought and water shortage are serious problems in many arid and semi-arid regions. This problem is getting worse and even continues in temperate climatic regions due to climate change. To address this problem, the use of biodegradable hydrogels is increasingly important for the application as water-retaining additives in soil. Furthermore, efficient (micro-)nutrient supply can be provided by the use of tailored hydrogels. Biodegradable polyaspartic acid (PASP) hydrogels with different available (1,6-hexamethylene diamine (HMD) and L-lysine (LYS)) and newly developed crosslinkers based on diesters of glycine (GLY) and (di-)ethylene glycol (DEG and EG, respectively) were synthesized and characterized using Fourier transform infrared (FTIR) spectroscopy and scanning electron microscopy (SEM) and regarding their swelling properties (kinetic, absorbency under load (AUL)) as well as biodegradability of PASP hydrogel. Copper (II) and zinc (II), respectively, were loaded as micronutrients in two different approaches: in situ with crosslinking and subsequent loading of prepared hydrogels. The results showed successful syntheses of di-glycine-ester-based crosslinkers. Hydrogels with good water-absorbing properties were formed. Moreover, the developed crosslinking agents in combination with the specific reaction conditions resulted in higher water absorbency with increased crosslinker content used in synthesis (10% vs. 20%). The prepared hydrogels are candidates for water-storing soil additives due to the biodegradability of PASP, which is shown in an exemple. The incorporation of Cu(II) and Zn(II) ions can provide these micronutrients for plant growth. KW - micronutrients KW - swelling properties KW - biodegradable polymers KW - hydrogels KW - superabsorbent polymers KW - glycine KW - polyaspartic acid Y1 - 2024 U6 - https://doi.org/10.3390/gels10030170 SN - 2310-2861 VL - 10 IS - 3 SP - Artikel 170 PB - MDPI CY - Basel ER - TY - RPRT A1 - Drescher, Hans Paul T1 - Critical review of the 1. Stokes’ problem and consequences for mixed turbulent/laminar flow N2 - The “1. Stokes’ problem”, the “suddenly accelerated flat wall”, is the oldest application of the Navier-Stokes equations. Stokes’ solution of the “problem” does not comply with the mathematical theorem of Cauchy and Kowalewskaya on the “Uniqueness and Existence” of solutions of partial differential equations and violates the physical theorem of minimum entropy production/dissipation of the Thermodynamics of Irreversible Processes. The result includes very high local shear stresses and dissipation rates. That is of special interest for the theory of turbulent and mixed turbulent/laminar flow. A textbook solution of the “1. Stokes Problem” is the Couette flow, which has a constant sheer stress along a linear profile. A consequence is that the Navier-Stokes equations do not describe any S-shaped part of a turbulent profile found in any turbulent Couette experiment. The paper surveys arguments referring to that statement, concerning the history of >150 years. Contrary to this there is always a Navier-Stokes solution near the wall, observed by a linear part of the Couette profile. There a turbulent description (e.g. by the logarithmic law-of-the-wall) fails completely. That is explained by the minimum dissipation requirement together with the Couette feature τ = const. The local co-existence of a turbulent zone and a laminar zone near the wall is stable and observed also at high Reynolds-Numbers. Y1 - 2024 ER - TY - PAT A1 - Hüning, Felix T1 - Positionssensorvorrichtung N2 - Die Erfindung betrifft eine Positionssensorvorrichtung zur Bestimmung einer Absolutposition eines beweglichen ersten Teils relativ zu einem ortsfesten zweiten Teil mit einem mit dem beweglichen ersten Teil gekoppelter Codekörper, der dazu eingerichtet ist, eine Codespur mit einer Mehrzahl von in Spurrichtung aufeinanderfolgenden Codeelementen zu enthalten zur Bildung eines Codewortes, mit einer magnetischen Detektionseinrichtung zur Detektion der Codespur, wobei die Detektionseinrichtung zum einen an dem Codekörper befestigte und entlang der Spurrichtung in einem solchen Abstand gegenpolig zueinander angeordnete Permanentmagneten aufweist, dass der Abstand mit einer vorgegebenen Länge der jeweiligen Codeelemente übereinstimmt, und zum anderen eine Anzahl von ortsfest und quer zu dem Codekörper versetzt angeordnete Wiegandsensoren aufweist, wobei der Abstand des Wiegandsensors zu einer Erstreckungsebene der Permanentmagneten derart gewählt ist, dass bei Überdeckung des Wiegandsensors durch den Permanentmagneten ein Wiegandpuls in dem Wiegandsensor induziert wird. Y1 - 2024 ER - TY - CHAP A1 - Neumann, Hannah A1 - Adam, Mario A1 - Backes, Klaus A1 - Börner, Martin A1 - Clees, Tanja A1 - Doetsch, Christian A1 - Glaeser, Susanne A1 - Herrmann, Ulf A1 - May, Johanna A1 - Rosenthal, Florian A1 - Sauer, Dirk Uwe A1 - Stadler, Ingo T1 - Development of open educational resources for renewable energy and the energy transition process T2 - ISES SWC 2021 N2 - The dissemination of knowledge about renewable energies is understood as a social task with the highest topicality. The transfer of teaching content on renewable energies into digital open educational resources offers the opportunity to significantly accelerate the implementation of the energy transition. Thus, in the here presented project six German universities create open educational resources for the energy transition. These materials are available to the public on the internet under a free license. So far there has been no publicly accessible, editable media that cover entire learning units about renewable energies extensively and in high technical quality. Thus, in this project, the content that remains up-to-date for a longer period is appropriately prepared in terms of media didactics. The materials enable lecturers to provide students with in-depth training about technologies for the energy transition. In a particular way, the created material is also suitable for making the general public knowledgeable about the energy transition with scientifically based material. KW - energy transition KW - renewable energies KW - open educational resources KW - dissemination KW - digitalization Y1 - 2021 U6 - https://doi.org/10.18086/swc.2021.47.03 N1 - ISES Solar World Congress, virtual conference 25-29 October 2021 PB - International Solar Energy Society CY - Freiburg ER - TY - CHAP A1 - Niederwestberg, Stefan A1 - Schneider, Falko A1 - Teixeira Boura, Cristiano José A1 - Herrmann, Ulf T1 - Introduction to a direct irradiated transparent tube particle receiver T2 - SOLARPACES 2020 N2 - New materials often lead to innovations and advantages in technical applications. This also applies to the particle receiver proposed in this work that deploys high-temperature and scratch resistant transparent ceramics. With this receiver design, particles are heated through direct-contact concentrated solar irradiance while flowing downwards through tubular transparent ceramics from top to bottom. In this paper, the developed particle receiver as well as advantages and disadvantages are described. Investigations on the particle heat-up characteristics from solar irradiance were carried out with DEM simulations which indicate that particle temperatures can reach up to 1200 K. Additionally, a simulation model was set up for investigating the dynamic behavior. A test receiver at laboratory scale has been designed and is currently being built. In upcoming tests, the receiver test rig will be used to validate the simulation results. The design and the measurement equipment is described in this work. KW - Solar irradiance KW - Ceramics Y1 - 2022 SN - 978-0-7354-4195-8 U6 - https://doi.org/10.1063/5.0086735 SN - 1551-7616 (online) SN - 0094-243X (print) N1 - SOLARPACES 2020: 26th International Conference on Concentrating Solar Power and Chemical Energy Systems, 28 September–2 October 2020, Freiburg, Germany IS - 2445 / 1 PB - AIP conference proceedings / American Institute of Physics CY - Melville, NY ER - TY - CHAP A1 - Caminos, Ricardo Alexander Chico A1 - Schmitz, Pascal A1 - Atti, Vikrama A1 - Mahdi, Zahra A1 - Teixeira Boura, Cristiano José A1 - Sattler, Johannes Christoph A1 - Herrmann, Ulf A1 - Hilger, Patrick A1 - Dieckmann, Simon T1 - Development of a micro heliostat and optical qualification assessment with a 3D laser scanning method T2 - SOLARPACES 2020 N2 - The Solar-Institut Jülich (SIJ) and the companies Hilger GmbH and Heliokon GmbH from Germany have developed a small-scale cost-effective heliostat, called “micro heliostat”. Micro heliostats can be deployed in small-scale concentrated solar power (CSP) plants to concentrate the sun's radiation for electricity generation, space or domestic water heating or industrial process heat. In contrast to conventional heliostats, the special feature of a micro heliostat is that it consists of dozens of parallel-moving, interconnected, rotatable mirror facets. The mirror facets array is fixed inside a box-shaped module and is protected from weathering and wind forces by a transparent glass cover. The choice of the building materials for the box, tracking mechanism and mirrors is largely dependent on the selected production process and the intended application of the micro heliostat. Special attention was paid to the material of the tracking mechanism as this has a direct influence on the accuracy of the micro heliostat. The choice of materials for the mirror support structure and the tracking mechanism is made in favor of plastic molded parts. A qualification assessment method has been developed by the SIJ in which a 3D laser scanner is used in combination with a coordinate measuring machine (CMM). For the validation of this assessment method, a single mirror facet was scanned and the slope deviation was computed. KW - Concentrated solar power KW - Electricity generation KW - Measuring instruments KW - Heliostats KW - Global change Y1 - 2022 SN - 978-0-7354-4195-8 U6 - https://doi.org/10.1063/5.0086262 SN - 1551-7616 (online) SN - 0094-243X (print) N1 - SOLARPACES 2020: 26th International Conference on Concentrating Solar Power and Chemical Energy Systems, 28 September–2 October 2020, Freiburg, Germany IS - 2445 / 1 PB - AIP conference proceedings / American Institute of Physics CY - Melville, NY ER - TY - CHAP A1 - Zahra, Mahdi A1 - Phani Srujan, Merige A1 - Caminos, Ricardo Alexander Chico A1 - Schmitz, Pascal A1 - Herrmann, Ulf A1 - Teixeira Boura, Cristiano José A1 - Schmitz, Mark A1 - Gielen, Hans A1 - Gedle, Yibekal A1 - Dersch, Jürgen T1 - Modeling the thermal behavior of solar salt in electrical resistance heaters for the application in PV-CSP hybrid power plants T2 - SOLARPACES 2020 N2 - Concentrated Solar Power (CSP) systems are able to store energy cost-effectively in their integrated thermal energy storage (TES). By intelligently combining Photovoltaics (PV) systems with CSP, a further cost reduction of solar power plants is expected, as well as an increase in dispatchability and flexibility of power generation. PV-powered Resistance Heaters (RH) can be deployed to raise the temperature of the molten salt hot storage from 385 °C up to 565 °C in a Parabolic Trough Collector (PTC) plant. To avoid freezing and decomposition of molten salt, the temperature distribution in the electrical resistance heater is investigated in the present study. For this purpose, a RH has been modeled and CFD simulations have been performed. The simulation results show that the hottest regions occur on the electric rod surface behind the last baffle. A technical optimization was performed by adjusting three parameters: Shell-baffle clearance, electric rod-baffle clearance and number of baffles. After the technical optimization was carried out, the temperature difference between the maximum temperature and the average outlet temperature of the salt is within the acceptable limits, thus critical salt decomposition has been avoided. Additionally, the CFD simulations results were analyzed and compared with results obtained with a one-dimensional model in Modelica. KW - Solar thermal technologies KW - Hybrid energy system KW - Concentrated solar power KW - Energy storage KW - Photovoltaics Y1 - 2022 SN - 978-0-7354-4195-8 U6 - https://doi.org/10.1063/5.0086268 SN - 1551-7616 (online) SN - 0094-243X (print) N1 - SOLARPACES 2020: 26th International Conference on Concentrating Solar Power and Chemical Energy Systems, 28 September–2 October 2020, Freiburg, Germany IS - 2445 / 1 PB - AIP conference proceedings / American Institute of Physics CY - Melville, NY ER - TY - JOUR A1 - Zhen, Manghao A1 - Liang, Yunpei A1 - Staat, Manfred A1 - Li, Quanqui A1 - Li, Jianbo T1 - Discontinuous fracture behaviors and constitutive model of sandstone specimens containing non-parallel prefabricated fissures under uniaxial compression JF - Theoretical and Applied Fracture Mechanics N2 - The deformation and damage laws of non-homogeneous irregular structural planes in rocks are the basis for studying the stability of rock engineering. To investigate the damage characteristics of rock containing non-parallel fissures, uniaxial compression tests and numerical simulations were conducted on sandstone specimens containing three non-parallel fissures inclined at 0°, 45° and 90° in this study. The characteristics of crack initiation and crack evolution of fissures with different inclinations were analyzed. A constitutive model for the discontinuous fractures of fissured sandstone was proposed. The results show that the fracture behaviors of fissured sandstone specimens are discontinuous. The stress–strain curves are non-smooth and can be divided into nonlinear crack closure stage, linear elastic stage, plastic stage and brittle failure stage, of which the plastic stage contains discontinuous stress drops. During the uniaxial compression test, the middle or ends of 0° fissures were the first to crack compared to 45° and 90° fissures. The end with small distance between 0° and 45° fissures cracked first, and the end with large distance cracked later. After the final failure, 0° fissures in all specimens were fractured, while 45° and 90° fissures were not necessarily fractured. Numerical simulation results show that the concentration of compressive stress at the tips of 0°, 45° and 90° fissures, as well as the concentration of tensile stress on both sides, decreased with the increase of the inclination angle. A constitutive model for the discontinuous fractures of fissured sandstone specimens was derived by combining the logistic model and damage mechanic theory. This model can well describe the discontinuous drops of stress and agrees well with the whole processes of the stress–strain curves of the fissured sandstone specimens. KW - Constitutive model KW - Damage mechanics theory KW - Discontinuous fractures KW - Uniaxial compression test KW - Non-parallel fissures Y1 - 2024 U6 - https://doi.org/10.1016/j.tafmec.2024.104373 SN - 0167-8442 VL - 131 PB - Elsevier CY - Amsterdam ER - TY - JOUR A1 - Engelmann, Ulrich M. A1 - Simsek, Beril A1 - Shalaby, Ahmed A1 - Krause, Hans-Joachim T1 - Key contributors to signal generation in frequency mixing magnetic detection (FMMD): an in silico study JF - Sensors N2 - Frequency mixing magnetic detection (FMMD) is a sensitive and selective technique to detect magnetic nanoparticles (MNPs) serving as probes for binding biological targets. Its principle relies on the nonlinear magnetic relaxation dynamics of a particle ensemble interacting with a dual frequency external magnetic field. In order to increase its sensitivity, lower its limit of detection and overall improve its applicability in biosensing, matching combinations of external field parameters and internal particle properties are being sought to advance FMMD. In this study, we systematically probe the aforementioned interaction with coupled Néel–Brownian dynamic relaxation simulations to examine how key MNP properties as well as applied field parameters affect the frequency mixing signal generation. It is found that the core size of MNPs dominates their nonlinear magnetic response, with the strongest contributions from the largest particles. The drive field amplitude dominates the shape of the field-dependent response, whereas effective anisotropy and hydrodynamic size of the particles only weakly influence the signal generation in FMMD. For tailoring the MNP properties and parameters of the setup towards optimal FMMD signal generation, our findings suggest choosing large particles of core sizes dc > 25 nm nm with narrow size distributions (σ < 0.1) to minimize the required drive field amplitude. This allows potential improvements of FMMD as a stand-alone application, as well as advances in magnetic particle imaging, hyperthermia and magnetic immunoassays. KW - key performance indicators KW - magnetic biosensing KW - coupled Néel–Brownian relaxation dynamics KW - frequency mixing magnetic detection KW - magnetic relaxation KW - micromagnetic simulation KW - magnetic nanoparticles Y1 - 2024 U6 - https://doi.org/10.3390/s24061945 SN - 1424-8220 N1 - This article belongs to the Special Issue "Advances in Magnetic Sensors and Their Applications" VL - 24 IS - 6 PB - MDPI CY - Basel ER - TY - BOOK A1 - Elsaesser, Evelyn A1 - Klebinggat, Michael A1 - Kuhn, Wilfried A1 - Michielsens, Constant A1 - Pauels, Willibert A1 - Popkes, Enno E. A1 - Schneider, Elke A1 - Laack, Walter van A1 - Warven, Rinus van ED - Laack, Walter van T1 - Schnittstelle Tod - Ist die Menschheit zu retten ohne Vertrauen auf ein Danach Y1 - 2024 SN - 978-3-936624-58-8 N1 - 8. Tagungsband zum NTE-Seminar in Aachen am, 11.11.2023 PB - van Laack Buchverlag CY - Aachen ER - TY - CHAP A1 - Mahdi, Zahra A1 - Dersch, Jürgen A1 - Schmitz, Pascal A1 - Dieckmann, Simon A1 - Caminos, Ricardo Alexander Chico A1 - Teixeira Boura, Cristiano José A1 - Herrmann, Ulf A1 - Schwager, Christian A1 - Schmitz, Mark A1 - Gielen, Hans A1 - Gedle, Yibekal A1 - Büscher, Rauno T1 - Technical assessment of Brayton cycle heat pumps for the integration in hybrid PV-CSP power plants T2 - SOLARPACES 2020 N2 - The hybridization of Concentrated Solar Power (CSP) and Photovoltaics (PV) systems is a promising approach to reduce costs of solar power plants, while increasing dispatchability and flexibility of power generation. High temperature heat pumps (HT HP) can be utilized to boost the salt temperature in the thermal energy storage (TES) of a Parabolic Trough Collector (PTC) system from 385 °C up to 565 °C. A PV field can supply the power for the HT HP, thus effectively storing the PV power as thermal energy. Besides cost-efficiently storing energy from the PV field, the power block efficiency of the overall system is improved due to the higher steam parameters. This paper presents a technical assessment of Brayton cycle heat pumps to be integrated in hybrid PV-CSP power plants. As a first step, a theoretical analysis was carried out to find the most suitable working fluid. The analysis included the fluids Air, Argon (Ar), Nitrogen (N2) and Carbon dioxide (CO2). N2 has been chosen as the optimal working fluid for the system. After the selection of the ideal working medium, different concepts for the arrangement of a HT HP in a PV-CSP hybrid power plant were developed and simulated in EBSILON®Professional. The concepts were evaluated technically by comparing the number of components required, pressure losses and coefficient of performance (COP). KW - Solar thermal technologies KW - Hybrid energy system KW - Concentrated solar power KW - Power plants KW - Energy storage Y1 - 2022 SN - 978-0-7354-4195-8 U6 - https://doi.org/10.1063/5.0086269 SN - 1551-7616 (online) SN - 0094-243X (print) N1 - SOLARPACES 2020: 26th International Conference on Concentrating Solar Power and Chemical Energy Systems, 28 September–2 October 2020, Freiburg, Germany IS - 2445 / 1 PB - AIP conference proceedings / American Institute of Physics CY - Melville, NY ER - TY - CHAP A1 - Gedle, Yibekal A1 - Schmitz, Mark A1 - Gielen, Hans A1 - Schmitz, Pascal A1 - Herrmann, Ulf A1 - Teixeira Boura, Cristiano José A1 - Mahdi, Zahra A1 - Caminos, Ricardo Alexander Chico A1 - Dersch, Jürgen T1 - Analysis of an integrated CSP-PV hybrid power plant T2 - SOLARPACES 2020 N2 - In the past, CSP and PV have been seen as competing technologies. Despite massive reductions in the electricity generation costs of CSP plants, PV power generation is - at least during sunshine hours - significantly cheaper. If electricity is required not only during the daytime, but around the clock, CSP with its inherent thermal energy storage gets an advantage in terms of LEC. There are a few examples of projects in which CSP plants and PV plants have been co-located, meaning that they feed into the same grid connection point and ideally optimize their operation strategy to yield an overall benefit. In the past eight years, TSK Flagsol has developed a plant concept, which merges both solar technologies into one highly Integrated CSP-PV-Hybrid (ICPH) power plant. Here, unlike in simply co-located concepts, as analyzed e.g. in [1] – [4], excess PV power that would have to be dumped is used in electric molten salt heaters to increase the storage temperature, improving storage and conversion efficiency. The authors demonstrate the electricity cost sensitivity to subsystem sizing for various market scenarios, and compare the resulting optimized ICPH plants with co-located hybrid plants. Independent of the three feed-in tariffs that have been assumed, the ICPH plant shows an electricity cost advantage of almost 20% while maintaining a high degree of flexibility in power dispatch as it is characteristic for CSP power plants. As all components of such an innovative concept are well proven, the system is ready for commercial market implementation. A first project is already contracted and in early engineering execution. KW - Hybrid energy system KW - Power plants KW - Electricity generation KW - Energy storage KW - Associated liquids Y1 - 2022 SN - 978-0-7354-4195-8 U6 - https://doi.org/10.1063/5.0086236 SN - 1551-7616 (online) SN - 0094-243X (print) N1 - SOLARPACES 2020: 26th International Conference on Concentrating Solar Power and Chemical Energy Systems, 28 September–2 October 2020, Freiburg, Germany IS - 2445 / 1 PB - AIP conference proceedings / American Institute of Physics CY - Melville, NY ER - TY - JOUR A1 - Schwager, Christian A1 - Flesch, Robert A1 - Schwarzbözl, Peter A1 - Herrmann, Ulf A1 - Teixeira Boura, Cristiano José T1 - Advanced two phase flow model for transient molten salt receiver system simulation JF - Solar Energy N2 - In order to realistically predict and optimize the actual performance of a concentrating solar power (CSP) plant sophisticated simulation models and methods are required. This paper presents a detailed dynamic simulation model for a Molten Salt Solar Tower (MST) system, which is capable of simulating transient operation including detailed startup and shutdown procedures including drainage and refill. For appropriate representation of the transient behavior of the receiver as well as replication of local bulk and surface temperatures a discretized receiver model based on a novel homogeneous two-phase (2P) flow modelling approach is implemented in Modelica Dymola®. This allows for reasonable representation of the very different hydraulic and thermal properties of molten salt versus air as well as the transition between both. This dynamic 2P receiver model is embedded in a comprehensive one-dimensional model of a commercial scale MST system and coupled with a transient receiver flux density distribution from raytracing based heliostat field simulation. This enables for detailed process prediction with reasonable computational effort, while providing data such as local salt film and wall temperatures, realistic control behavior as well as net performance of the overall system. Besides a model description, this paper presents some results of a validation as well as the simulation of a complete startup procedure. Finally, a study on numerical simulation performance and grid dependencies is presented and discussed. KW - Molten salt solar tower KW - Molten salt receiver system KW - Dynamic simulation KW - Two-phase modelling KW - Transient flux distribution Y1 - 2022 U6 - https://doi.org/10.1016/j.solener.2021.12.065 SN - 0038-092X (print) SN - 1471-1257 (online) VL - 232 SP - 362 EP - 375 PB - Elsevier CY - Amsterdam ER - TY - CHAP A1 - Schwager, Christian A1 - Angele, Florian A1 - Schwarzbözl, Peter A1 - Teixeira Boura, Cristiano José A1 - Herrmann, Ulf T1 - Model predictive assistance for operational decision making in molten salt receiver systems T2 - SolarPACES: Solar Power & Chemical Energy Systems N2 - Despite the challenges of pioneering molten salt towers (MST), it remains the leading technology in central receiver power plants today, thanks to cost effective storage integration and high cost reduction potential. The limited controllability in volatile solar conditions can cause significant losses, which are difficult to estimate without comprehensive modeling [1]. This paper presents a Methodology to generate predictions of the dynamic behavior of the receiver system as part of an operating assistance system (OAS). Based on this, it delivers proposals if and when to drain and refill the receiver during a cloudy period in order maximize the net yield and quantifies the amount of net electricity gained by this. After prior analysis with a detailed dynamic two-phase model of the entire receiver system, two different reduced modeling approaches where developed and implemented in the OAS. A tailored decision algorithm utilizes both models to deliver the desired predictions efficiently and with appropriate accuracy. KW - Power plants KW - Associated liquids KW - Decision theory KW - Electrochemistry Y1 - 2023 SN - 978-0-7354-4623-6 U6 - https://doi.org/10.1063/5.0151514 SN - 1551-7616 (online) SN - 0094-243X (print) N1 - SolarPACES: SOLAR POWER & CHEMICAL ENERGY SYSTEMS: 27th International Conference on Concentrating Solar Power and Chemical Energy Systems, 27 September–1 October 2021, Online IS - 2815 / 1 PB - AIP conference proceedings / American Institute of Physics CY - Melville, NY ER - TY - CHAP A1 - Schulte, Jonas A1 - Schwager, Christian A1 - Noureldin, Kareem A1 - May, Martin A1 - Teixeira Boura, Cristiano José A1 - Herrmann, Ulf T1 - Gradient controlled startup procedure of a molten-salt power-to-heat energy storage plant based on dynamic process simulation T2 - SolarPACES: Solar Power & Chemical Energy Systems N2 - The integration of high temperature thermal energy storages into existing conventional power plants can help to reduce the CO2 emissions of those plants and lead to lower capital expenditures for building energy storage systems, due to the use of synergy effects [1]. One possibility to implement that, is a molten salt storage system with a powerful power-to-heat unit. This paper presents two possible control concepts for the startup of the charging system of such a facility. The procedures are implemented in a detailed dynamic process model. The performance and safety regarding the film temperatures at heat transmitting surfaces are investigated in the process simulations. To improve the accuracy in predicting the film temperatures, CFD simulations of the electrical heater are carried out and the results are merged with the dynamic model. The results show that both investigated control concepts are safe regarding the temperature limits. The gradient controlled startup performed better than the temperature-controlled startup. Nevertheless, there are several uncertainties that need to be investigated further. KW - Power plants KW - Energy storage KW - Associated liquids Y1 - 2023 SN - 978-0-7354-4623-6 U6 - https://doi.org/10.1063/5.0148741 SN - 1551-7616 (online) SN - 0094-243X (print) N1 - SolarPACES: SOLAR POWER & CHEMICAL ENERGY SYSTEMS: 27th International Conference on Concentrating Solar Power and Chemical Energy Systems, 27 September–1 October 2021, Online IS - 2815 / 1 PB - AIP conference proceedings / American Institute of Physics CY - Melville, NY ER - TY - CHAP A1 - Lahrs, Lennart A1 - Krisam, Pierre A1 - Herrmann, Ulf T1 - Envisioning a collaborative energy system planning platform for the energy transition at the district level T2 - ECOS 2023. The 36th International Conference on Efficiency, Cost, Optimization, Simulation and Environmental Impact of Energy Systems N2 - Residential and commercial buildings account for more than one-third of global energy-related greenhouse gas emissions. Integrated multi-energy systems at the district level are a promising way to reduce greenhouse gas emissions by exploiting economies of scale and synergies between energy sources. Planning district energy systems comes with many challenges in an ever-changing environment. Computational modelling established itself as the state-of-the-art method for district energy system planning. Unfortunately, it is still cumbersome to combine standalone models to generate insights that surpass their original purpose. Ideally, planning processes could be solved by using modular tools that easily incorporate the variety of competing and complementing computational models. Our contribution is a vision for a collaborative development and application platform for multi-energy system planning tools at the district level. We present challenges of district energy system planning identified in the literature and evaluate whether this platform can help to overcome these challenges. Further, we propose a toolkit that represents the core technical elements of the platform. Lastly, we discuss community management and its relevance for the success of projects with collaboration and knowledge sharing at their core. KW - Energy system planning KW - District energy planning platform KW - District data model KW - Renewable energy integration Y1 - 2023 U6 - https://doi.org/10.52202/069564-0284 N1 - ECOS 2023. The 36th International Conference on Efficiency, Cost, Optimization, Simulation and Environmental Impact of Energy Systems, 25-30 JUNE, 2023, Las Palmas de Gran Canaria, Spain SP - 3163 EP - 3170 PB - Procedings of ECOS 2023 ER - TY - INPR A1 - Grieger, Niklas A1 - Mehrkanoon, Siamak A1 - Bialonski, Stephan T1 - Preprint: Data-efficient sleep staging with synthetic time series pretraining T2 - arXiv N2 - Analyzing electroencephalographic (EEG) time series can be challenging, especially with deep neural networks, due to the large variability among human subjects and often small datasets. To address these challenges, various strategies, such as self-supervised learning, have been suggested, but they typically rely on extensive empirical datasets. Inspired by recent advances in computer vision, we propose a pretraining task termed "frequency pretraining" to pretrain a neural network for sleep staging by predicting the frequency content of randomly generated synthetic time series. Our experiments demonstrate that our method surpasses fully supervised learning in scenarios with limited data and few subjects, and matches its performance in regimes with many subjects. Furthermore, our results underline the relevance of frequency information for sleep stage scoring, while also demonstrating that deep neural networks utilize information beyond frequencies to enhance sleep staging performance, which is consistent with previous research. We anticipate that our approach will be advantageous across a broad spectrum of applications where EEG data is limited or derived from a small number of subjects, including the domain of brain-computer interfaces. Y1 - 2024 ER - TY - CHAP A1 - Schulte, Jonas A1 - Schwager, Christian A1 - Frantz, Cathy A1 - Schloms, Felix A1 - Teixeira Boura, Cristiano José A1 - Herrmann, Ulf T1 - Control concept for a molten salt receiver in star design: Development, optimization and testing with cloud passage scenarios T2 - SolarPACES 2022 conference proceedings N2 - A promising approach to reduce the system costs of molten salt solar receivers is to enable the irradiation of the absorber tubes on both sides. The star design is an innovative receiver design, pursuing this approach. The unconventional design leads to new challenges in controlling the system. This paper presents a control concept for a molten salt receiver system in star design. The control parameters are optimized in a defined test cycle by minimizing a cost function. The control concept is tested in realistic cloud passage scenarios based on real weather data. During these tests, the control system showed no sign of unstable behavior, but to perform sufficiently in every scenario further research and development like integrating Model Predictive Controls (MPCs) need to be done. The presented concept is a starting point to do so. KW - Molten salt receiver KW - Star design KW - Control optimization KW - Cloud passages Y1 - 2023 U6 - https://doi.org/10.52825/solarpaces.v1i.693 SN - 2751-9899 (online) N1 - SolarPACES 2022, 28th International Conference on Concentrating Solar Power and Chemical Energy Systems, 27-30 September, Albuquerque, NM, USA IS - 1 PB - TIB Open Publishing CY - Hannover ER - TY - CHAP A1 - Schwager, Christian A1 - Angele, Florian A1 - Nouri, Bijan A1 - Schwarzbözl, Peter A1 - Teixeira Boura, Cristiano José A1 - Herrmann, Ulf T1 - Impact of DNI forecast quality on performance prediction for a commercial scale solar tower: Application of nowcasting DNI maps to dynamic solar tower simulation T2 - SolarPACES 2022 conference proceedings N2 - Concerning current efforts to improve operational efficiency and to lower overall costs of concentrating solar power (CSP) plants with prediction-based algorithms, this study investigates the quality and uncertainty of nowcasting data regarding the implications for process predictions. DNI (direct normal irradiation) maps from an all-sky imager-based nowcasting system are applied to a dynamic prediction model coupled with ray tracing. The results underline the need for high-resolution DNI maps in order to predict net yield and receiver outlet temperature realistically. Furthermore, based on a statistical uncertainty analysis, a correlation is developed, which allows for predicting the uncertainty of the net power prediction based on the corresponding DNI forecast uncertainty. However, the study reveals significant prediction errors and the demand for further improvement in the accuracy at which local shadings are forecasted. KW - Process prediction KW - DNI forecasting KW - Nowcasting KW - Uncertainty analysis KW - Molten salt receiver system, Y1 - 2024 U6 - https://doi.org/10.52825/solarpaces.v1i.675 SN - 2751-9899 (online) N1 - SolarPACES 2022, 28th International Conference on Concentrating Solar Power and Chemical Energy Systems, 27-30 September, Albuquerque, NM, USA IS - 1 PB - TIB Open Publishing CY - Hannover ER - TY - CHAP A1 - Sattler, Johannes Christoph A1 - Atti, Vikrama A1 - Alexopoulos, Spiros A1 - Teixeira Boura, Cristiano José A1 - Herrmann, Ulf A1 - Dutta, Siddharth A1 - Kioutsioukis, Ioannis T1 - DNI forecast tool for the smart operation of a parabolic trough collector system with concrete thermal energy storage: Theory, results and outlook T2 - SolarPACES 2022 conference proceedings N2 - This work presents a basic forecast tool for predicting direct normal irradiance (DNI) in hourly resolution, which the Solar-Institut Jülich (SIJ) is developing within a research project. The DNI forecast data shall be used for a parabolic trough collector (PTC) system with a concrete thermal energy storage (C-TES) located at the company KEAN Soft Drinks Ltd in Limassol, Cyprus. On a daily basis, 24-hour DNI prediction data in hourly resolution shall be automatically produced using free or very low-cost weather forecast data as input. The purpose of the DNI forecast tool is to automatically transfer the DNI forecast data on a daily basis to a main control unit (MCU). The MCU automatically makes a smart decision on the operation mode of the PTC system such as steam production mode and/or C-TES charging mode. The DNI forecast tool was evaluated using historical data of measured DNI from an on-site weather station, which was compared to the DNI forecast data. The DNI forecast tool was tested using data from 56 days between January and March 2022, which included days with a strong variation in DNI due to cloud passages. For the evaluation of the DNI forecast reliability, three categories were created and the forecast data was sorted accordingly. The result was that the DNI forecast tool has a reliability of 71.4 % based on the tested days. The result fulfils SIJ’s aim to achieve a reliability of around 70 %, but SIJ aims to still improve the DNI forecast quality. KW - Direct normal irradiance forecast KW - DNI forecast KW - Parabolic trough collector KW - PTC KW - Thermal Energy Storage Y1 - 2024 U6 - https://doi.org/10.52825/solarpaces.v1i.731 SN - 2751-9899 (online) N1 - SolarPACES 2022, 28th International Conference on Concentrating Solar Power and Chemical Energy Systems, 27-30 September, Albuquerque, NM, USA IS - 1 PB - TIB Open Publishing CY - Hannover ER - TY - CHAP A1 - Sattler, Johannes Christoph A1 - Schneider, Iesse Peer A1 - Angele, Florian A1 - Atti, Vikrama A1 - Teixeira Boura, Cristiano José A1 - Herrmann, Ulf T1 - Development of heliostat field calibration methods: Theory and experimental test results T2 - SolarPACES 2022 conference proceedings N2 - In this work, three patent pending calibration methods for heliostat fields of central receiver systems (CRS) developed by the Solar-Institut Jülich (SIJ) of the FH Aachen University of Applied Sciences are presented. The calibration methods can either operate in a combined mode or in stand-alone mode. The first calibration method, method A, foresees that a camera matrix is placed into the receiver plane where it is subjected to concentrated solar irradiance during a measurement process. The second calibration method, method B, uses an unmanned aerial vehicle (UAV) such as a quadrocopter to automatically fly into the reflected solar irradiance cross-section of one or more heliostats (two variants of method B were tested). The third calibration method, method C, foresees a stereo central camera or multiple stereo cameras installed e.g. on the solar tower whereby the orientations of the heliostats are calculated from the location detection of spherical red markers attached to the heliostats. The most accurate method is method A which has a mean accuracy of 0.17 mrad. The mean accuracy of method B variant 1 is 1.36 mrad and of variant 2 is 1.73 mrad. Method C has a mean accuracy of 15.07 mrad. For method B there is great potential regarding improving the measurement accuracy. For method C the collected data was not sufficient for determining whether or not there is potential for improving the accuracy. KW - Heliostat Field Calibration KW - Unmanned aerial vehicle KW - UAV KW - Quadrocopter KW - Camera system Y1 - 2024 U6 - https://doi.org/10.52825/solarpaces.v1i.678 SN - 2751-9899 (online) N1 - SolarPACES 2022: 28th International Conference on Concentrating Solar Power and Chemical Energy Systems, 27-30 September, Albuquerque, NM, USA IS - 1 PB - TIB Open Publishing CY - Hannover ER - TY - CHAP A1 - Dachwald, Bernd A1 - Wurm, P. T1 - Mission analysis for an advanced solar photon thruster T2 - 60th International Astronautical Congress 2009, IAC 2009 N2 - The so-called "compound solar sail", also known as "Solar Photon Thruster" (SPT), is a solar sail design concept, for which the two basic functions of the solar sail, namely light collection and thrust direction, are uncoupled. In this paper, we introduce a novel SPT concept, termed the Advanced Solar Photon Thruster (ASPT). This model does not suffer from the simplified assumptions that have been made for the analysis of compound solar sails in previous studies. We present the equations that describe the force, which acts on the ASPT. After a detailed design analysis, the performance of the ASPT with respect to the conventional flat solar sail (FSS) is investigated for three interplanetary mission scenarios: An Earth-Venus rendezvous, where the solar sail has to spiral towards the Sun, an Earth-Mars rendezvous, where the solar sail has to spiral away from the Sun, and an Earth-NEA rendezvous (to near-Earth asteroid 1996FG3), where a large orbital eccentricity change is required. The investigated solar sails have realistic near-term characteristic accelerations between 0.1 and 0.2mm/s2. Our results show that a SPT is not superior to the flat solar sail unless very idealistic assumptions are made. KW - Interplanetary flight Y1 - 2009 SN - 978-161567908-9 N1 - 60th International Astronautical Congress 2009, IAC 2009; Daejeon; South Korea; 12 October 2009 through 16 October 2009 VL - 8 SP - 6838 EP - 6851 PB - Elsevier CY - Amsterdam ER - TY - CHAP A1 - Dachwald, Bernd ED - Knopf, George K. ED - Otani, Yukitoshi T1 - Light propulsion systems for spacecraft T2 - Optical nano and micro actuator technology Y1 - 2017 SN - 9781315217628 (eBook) SP - 577 EP - 598 PB - CRC Press CY - Boca Raton ER - TY - CHAP A1 - Dachwald, Bernd A1 - Wurm, P. T1 - Design concept and modeling of an advanced solar photon thruster T2 - Advances in the Astronautical Sciences N2 - The so-called "compound solar sail", also known as "Solar Photon Thruster" (SPT), holds the potential of providing significant performance advantages over the flat solar sail. Previous SPT design concepts, however, do not consider shadowing effects and multiple reflections of highly concentrated solar radiation that would inevitably destroy the gossamer sail film. In this paper, we propose a novel advanced SPT (ASPT) design concept that does not suffer from these oversimplifications. We present the equations that describe the thrust force acting on such a sail system and compare its performance with respect to the conventional flat solar sail. KW - solar sails Y1 - 2009 SN - 978-087703554-1 SN - 00653438 N1 - 19th AAS/AIAA Space Flight Mechanics Meeting; Savannah, GA; United States; 8 February 2009 through 12 February 2009 SP - 723 EP - 740 PB - American Astronautical Society CY - San Diego, Calif. ER - TY - CHAP A1 - Gehler, M. A1 - Ober-Blöbaum, S. A1 - Dachwald, Bernd T1 - Application of discrete mechanics and optimal control to spacecraft in non-keplerian motion around small solar system bodies T2 - Procceedings of the 60th International Astronautical Congress N2 - Prolonged operations close to small solar system bodies require a sophisticated control logic to minimize propellant mass and maximize operational efficiency. A control logic based on Discrete Mechanics and Optimal Control (DMOC) is proposed and applied to both conventionally propelled and solar sail spacecraft operating at an arbitrarily shaped asteroid in the class of Itokawa. As an example, stand-off inertial hovering is considered, recently identified as a challenging part of the Marco Polo mission. The approach is easily extended to stand-off orbits. We show that DMOC is applicable to spacecraft control at small objects, in particular with regard to the fact that the changes in gravity are exploited by the algorithm to optimally control the spacecraft position. Furthermore, we provide some remarks on promising developments. KW - Spacecraft Y1 - 2009 SN - 978-161567908-9 N1 - 60th International Astronautical Congress 2009, IAC 2009; Daejeon; South Korea; 12 October 2009 through 16 October 2009 SP - 1360 EP - 1371 PB - Elsevier CY - Amsterdam ER - TY - CHAP A1 - Funke, Harald A1 - Beckmann, Nils A1 - Stefan, Lukas A1 - Keinz, Jan T1 - Hydrogen combustor integration study for a medium range aircraft engine using the dry-low NOx “Micromix” combustion principle T2 - Proceedings of the ASME Turbo Expo 2023: Turbomachinery Technical Conference and Exposition. Volume 1: Aircraft Engine. N2 - The feasibility study presents results of a hydrogen combustor integration for a Medium-Range aircraft engine using the Dry-Low-NOₓ Micromix combustion principle. Based on a simplified Airbus A320-type flight mission, a thermodynamic performance model of a kerosene and a hydrogen-powered V2530-A5 engine is used to derive the thermodynamic combustor boundary conditions. A new combustor design using the Dry-Low NOx Micromix principle is investigated by slice model CFD simulations of a single Micromix injector for design and off-design operation of the engine. Combustion characteristics show typical Micromix flame shapes and good combustion efficiencies for all flight mission operating points. Nitric oxide emissions are significant below ICAO CAEP/8 limits. For comparison of the Emission Index (EI) for NOₓ emissions between kerosene and hydrogen operation, an energy (kerosene) equivalent Emission Index is used. A full 15° sector model CFD simulation of the combustion chamber with multiple Micromix injectors including inflow homogenization and dilution and cooling air flows investigates the combustor integration effects, resulting NOₓ emission and radial temperature distributions at the combustor outlet. The results show that the integration of a Micromix hydrogen combustor in actual aircraft engines is feasible and offers, besides CO₂ free combustion, a significant reduction of NOₓ emissions compared to kerosene operation. KW - emission index KW - nitric oxides KW - aircraft engine KW - Micromix KW - combustion KW - hydrogen Y1 - 2023 SN - 978-0-7918-8693-9 U6 - https://doi.org/10.1115/GT2023-102370 N1 - Paper No. GT2023-102370, V001T01A022 N1 - ASME Turbo Expo 2023: Turbomachinery Technical Conference and Exposition June 26–30, 2023, Boston, Massachusetts, USA PB - ASME CY - New York ER - TY - JOUR A1 - Bornheim, Tobias A1 - Grieger, Niklas A1 - Blaneck, Patrick Gustav A1 - Bialonski, Stephan T1 - Speaker Attribution in German Parliamentary Debates with QLoRA-adapted Large Language Models JF - Journal for language technology and computational linguistics : JLCL N2 - The growing body of political texts opens up new opportunities for rich insights into political dynamics and ideologies but also increases the workload for manual analysis. Automated speaker attribution, which detects who said what to whom in a speech event and is closely related to semantic role labeling, is an important processing step for computational text analysis. We study the potential of the large language model family Llama 2 to automate speaker attribution in German parliamentary debates from 2017-2021. We fine-tune Llama 2 with QLoRA, an efficient training strategy, and observe our approach to achieve competitive performance in the GermEval 2023 Shared Task On Speaker Attribution in German News Articles and Parliamentary Debates. Our results shed light on the capabilities of large language models in automating speaker attribution, revealing a promising avenue for computational analysis of political discourse and the development of semantic role labeling systems. KW - large language models KW - German KW - speaker attribution KW - semantic role labeling Y1 - 2024 U6 - https://doi.org/10.21248/jlcl.37.2024.244 SN - 2190-6858 VL - 37 IS - 1 PB - Gesellschaft für Sprachtechnologie und Computerlinguistik CY - Regensburg ER - TY - CHAP A1 - Altherr, Lena A1 - Döring, Bernd A1 - Frauenrath, Tobias A1 - Groß, Rolf A1 - Mohan, Nijanthan A1 - Oyen, Marc A1 - Schnittcher, Lukas A1 - Voß, Norbert ED - Reiff-Stephan, Jörg ED - Jäkel, Jens ED - Schwarz, André T1 - DiggiTwin: ein interdisziplinäres Projekt zur Nutzung digitaler Zwillinge auf dem Weg zu einem klimaneutralen Gebäudebestand T2 - Tagungsband AALE 2024 : Fit für die Zukunft: praktische Lösungen für die industrielle Automation N2 - Im Hinblick auf die Klimaziele der Bundesrepublik Deutschland konzentriert sich das Projekt Diggi Twin auf die nachhaltige Gebäudeoptimierung. Grundlage für eine ganzheitliche Gebäudeüberwachung und -optimierung bildet dabei die Digitalisierung und Automation im Sinne eines Smart Buildings. Das interdisziplinäre Projekt der FH Aachen hat das Ziel, ein bestehendes Hochschulgebäude und einen Neubau an klimaneutrale Standards anzupassen. Im Rahmen des Projekts werden bekannte Verfahren, wie das Building Information Modeling (BIM), so erweitert, dass ein digitaler Gebäudezwilling entsteht. Dieser kann zur Optimierung des Gebäudebetriebs herangezogen werden, sowie als Basis für eine Erweiterung des Bewertungssystems Nachhaltiges Bauen (BNB) dienen. Mithilfe von Sensortechnologie und künstlicher Intelligenz kann so ein präzises Monitoring wichtiger Gebäudedaten erfolgen, um ungenutzte Energieeinsparpotenziale zu erkennen und zu nutzen. Das Projekt erforscht und setzt methodische Erkenntnisse zu BIM und digitalen Gebäudezwillingen praxisnah um, indem es spezifische Fragen zur Energie- und Ressourceneffizienz von Gebäuden untersucht und konkrete Lösungen für die Gebäudeoptimierung entwickelt. KW - Anomalieerkennung KW - IoT KW - Überwachung & Optimierung KW - DiggiTwin KW - BIM KW - Smart Building KW - Digitalisierung Y1 - 2024 SN - 978-3-910103-02-3 U6 - https://doi.org/10.33968/2024.67 N1 - 20. AALE-Konferenz. Bielefeld, 06.03.-08.03.2024 (Tagungsband unter https://doi.org/10.33968/2024.29) SP - 341 EP - 346 PB - le-tex publishing services GmbH CY - Leipzig ER - TY - CHAP A1 - Wittig, M. A1 - Rütters, René A1 - Bragard, Michael ED - Reiff-Stephan, Jörg ED - Jäkel, Jens ED - Schwarz, André T1 - Application of RL in control systems using the example of a rotatory inverted pendulum T2 - Tagungsband AALE 2024 : Fit für die Zukunft: praktische Lösungen für die industrielle Automation N2 - In this paper, the use of reinforcement learning (RL) in control systems is investigated using a rotatory inverted pendulum as an example. The control behavior of an RL controller is compared to that of traditional LQR and MPC controllers. This is done by evaluating their behavior under optimal conditions, their disturbance behavior, their robustness and their development process. All the investigated controllers are developed using MATLAB and the Simulink simulation environment and later deployed to a real pendulum model powered by a Raspberry Pi. The RL algorithm used is Proximal Policy Optimization (PPO). The LQR controller exhibits an easy development process, an average to good control behavior and average to good robustness. A linear MPC controller could show excellent results under optimal operating conditions. However, when subjected to disturbances or deviations from the equilibrium point, it showed poor performance and sometimes instable behavior. Employing a nonlinear MPC Controller in real time was not possible due to the high computational effort involved. The RL controller exhibits by far the most versatile and robust control behavior. When operated in the simulation environment, it achieved a high control accuracy. When employed in the real system, however, it only shows average accuracy and a significantly greater performance loss compared to the simulation than the traditional controllers. With MATLAB, it is not yet possible to directly post-train the RL controller on the Raspberry Pi, which is an obstacle to the practical application of RL in a prototyping or teaching setting. Nevertheless, RL in general proves to be a flexible and powerful control method, which is well suited for complex or nonlinear systems where traditional controllers struggle. KW - Rotatory Inverted Pendulum KW - MPC KW - LQR KW - PPO KW - Reinforcement Learning Y1 - 2024 SN - 978-3-910103-02-3 U6 - https://doi.org/10.33968/2024.53 N1 - 20. AALE-Konferenz. Bielefeld, 06.03.-08.03.2024. (Tagungsband unter https://doi.org/10.33968/2024.29) SP - 241 EP - 248 PB - le-tex publishing services GmbH CY - Leipzig ER - TY - PAT A1 - Bragard, Michael A1 - Hüning, Felix A1 - Kowalewski, Paul T1 - Vorrichtung zur Relativlagenbestimmung [Offenlegungschrift] N2 - Die Erfindung betrifft eine Vorrichtung zur Bestimmung einer Relativlage zwischen einem feststehenden Teil und einem zu demselben in eine Bewegungsrichtung bewegbaren beweglichen Teil, wobei der feststehende Teil mit einem Wiegandsensor versehen ist, wobei der Wiegandsensor zwischen zwei gegenpolig zueinander ausgebildeten Permanentmagneten angeordnet ist und dass der bewegliche Teil eine Mehrzahl von beabstandet zueinander angeordneten Magnetisierungsstegen aus einem magnetisch leitenden Material aufweist, die in der Bewegungsrichtung zumindest eine gleich große Erstreckung aufweisen wie der Permanentmagnet, dass ein Abstand zwischen benachbarten Magnetisierungsstegen derart gewählt ist, dass in einer ersten Relativlage ein erster Permanentmagnet von einem der Magnetisierungsstege überdeckt ist und ein zweiter Permanentmagnet nicht von einem der Magnetisierungsstege überdeckt ist. Y1 - 2023 N1 - Offenlegungschrift zu DE102022115350A1 2023.12.21 ER - TY - CHAP A1 - Grund, Raphael M. A1 - Altherr, Lena ED - Reiff-Stephan, Jörg ED - Jäkel, Jens ED - Schwarz, André T1 - Development of an open source energy disaggregation tool for the home automation platform Home Assistant T2 - Tagungsband AALE 2023 : mit Automatisierung gegen den Klimawandel N2 - In order to reduce energy consumption of homes, it is important to make transparent which devices consume how much energy. However, power consumption is often only monitored aggregated at the house energy meter. Disaggregating this power consumption into the contributions of individual devices can be achieved using Machine Learning. Our work aims at making state of the art disaggregation algorithms accessibe for users of the open source home automation platform Home Assistant. KW - Home Automation Platform KW - Home Assistant KW - Open Source KW - Machine Learning KW - Energy Disaggregation Y1 - 2023 SN - 978-3-910103-01-6 U6 - https://doi.org/10.33968/2023.02 N1 - 19. AALE-Konferenz. Luxemburg, 08.03.-10.03.2023. BTS Connected Buildings & Cities Luxemburg (Tagungsband unter https://doi.org/10.33968/2023.01) SP - 11 EP - 20 PB - le-tex publishing services GmbH CY - Leipzig ER - TY - JOUR A1 - Kahmann, Stephanie L. A1 - Rausch, Valentin A1 - Plümer, Jonathan A1 - Müller, Lars P. A1 - Pieper, Martin A1 - Wegmann, Kilian T1 - The automized fracture edge detection and generation of three-dimensional fracture probability heat maps JF - Medical Engineering & Physics N2 - With proven impact of statistical fracture analysis on fracture classifications, it is desirable to minimize the manual work and to maximize repeatability of this approach. We address this with an algorithm that reduces the manual effort to segmentation, fragment identification and reduction. The fracture edge detection and heat map generation are performed automatically. With the same input, the algorithm always delivers the same output. The tool transforms one intact template consecutively onto each fractured specimen by linear least square optimization, detects the fragment edges in the template and then superimposes them to generate a fracture probability heat map. We hypothesized that the algorithm runs faster than the manual evaluation and with low (< 5 mm) deviation. We tested the hypothesis in 10 fractured proximal humeri and found that it performs with good accuracy (2.5 mm ± 2.4 mm averaged Euclidean distance) and speed (23 times faster). When applied to a distal humerus, a tibia plateau, and a scaphoid fracture, the run times were low (1–2 min), and the detected edges correct by visual judgement. In the geometrically complex acetabulum, at a run time of 78 min some outliers were considered acceptable. An automatically generated fracture probability heat map based on 50 proximal humerus fractures matches the areas of high risk of fracture reported in medical literature. Such automation of the fracture analysis method is advantageous and could be extended to reduce the manual effort even further. KW - Fracture classification KW - Shoulder KW - Probability distribution mapping KW - Morphing KW - Imaging Y1 - 2022 SN - 1350-4533 VL - 2022 IS - 110 PB - Elsevier CY - Amsterdam ER - TY - JOUR A1 - Schoenrock, Britt A1 - Muckelt, Paul E. A1 - Hastermann, Maria A1 - Albracht, Kirsten A1 - MacGregor, Robert A1 - Martin, David A1 - Gunga, Hans-Christian A1 - Salanova, Michele A1 - Stokes, Maria J. A1 - Warner, Martin B. A1 - Blottner, Dieter T1 - Muscle stiffness indicating mission crew health in space JF - Scientific Reports N2 - Muscle function is compromised by gravitational unloading in space affecting overall musculoskeletal health. Astronauts perform daily exercise programmes to mitigate these effects but knowing which muscles to target would optimise effectiveness. Accurate inflight assessment to inform exercise programmes is critical due to lack of technologies suitable for spaceflight. Changes in mechanical properties indicate muscle health status and can be measured rapidly and non-invasively using novel technology. A hand-held MyotonPRO device enabled monitoring of muscle health for the first time in spaceflight (> 180 days). Greater/maintained stiffness indicated countermeasures were effective. Tissue stiffness was preserved in the majority of muscles (neck, shoulder, back, thigh) but Tibialis Anterior (foot lever muscle) stiffness decreased inflight vs. preflight (p < 0.0001; mean difference 149 N/m) in all 12 crewmembers. The calf muscles showed opposing effects, Gastrocnemius increasing in stiffness Soleus decreasing. Selective stiffness decrements indicate lack of preservation despite daily inflight countermeasures. This calls for more targeted exercises for lower leg muscles with vital roles as ankle joint stabilizers and in gait. Muscle stiffness is a digital biomarker for risk monitoring during future planetary explorations (Moon, Mars), for healthcare management in challenging environments or clinical disorders in people on Earth, to enable effective tailored exercise programmes. KW - Ageing KW - Anatomy KW - Muscle KW - Musculoskeletal system KW - Physiology Y1 - 2024 U6 - https://doi.org/10.1038/s41598-024-54759-6 SN - 2045-2322 N1 - Corresponding author: Dieter Blottner VL - 14 IS - Article number: 4196 PB - Springer Nature CY - London ER - TY - CHAP A1 - Gömmel, A. A1 - Butenweg, Christoph A1 - Kob, M. T1 - A fluid-structure interaction model of vocal fold oscillation T2 - 5th International Workshop on Models and Analysis of Vocal Emissions for Biomedical Applications, MAVEBA 2007 N2 - Since fluid-structure interaction within the finite-element method is state of the art in many engineering fields, this method is used in voice analysis. A quasi two-dimensional model of the vocal folds including the ventricular folds is presented. First results of self-sustained vocal fold oscillation are presented and possibilities as well as limitations are discussed. KW - finite element method KW - fluid structure interaction KW - vocal fold oscillation Y1 - 2007 SN - 978-888453674-7 N1 - 5th International Workshop on Models and Analysis of Vocal Emissions for Biomedical Applications, MAVEBA 2007; Florence; Italy; 13 December 2007 through 15 December 2007 SP - 127 EP - 128 ER - TY - JOUR A1 - Baumgartner, Werner A1 - Fidler, Florian A1 - Weth, Agnes A1 - Habbecke, Martin A1 - Jakob, Peter A1 - Butenweg, Christoph A1 - Böhme, Wolfgang T1 - Investigating the locomotion of the sandfish in desert sand using NMR-Imaging JF - PLOS ONE N2 - The sandfish (Scincus scincus) is a lizard having the remarkable ability to move through desert sand for significant distances. It is well adapted to living in loose sand by virtue of a combination of morphological and behavioural specializations. We investigated the bodyform of the sandfish using 3D-laserscanning and explored its locomotion in loose desert sand using fast nuclear magnetic resonance (NMR) imaging. The sandfish exhibits an in-plane meandering motion with a frequency of about 3 Hz and an amplitude of about half its body length accompanied by swimming-like (or trotting) movements of its limbs. No torsion of the body was observed, a movement required for a digging-behaviour. Simple calculations based on the Janssen model for granular material related to our findings on bodyform and locomotor behaviour render a local decompaction of the sand surrounding the moving sandfish very likely. Thus the sand locally behaves as a viscous fluid and not as a solid material. In this fluidised sand the sandfish is able to “swim” using its limbs. KW - magnetic resonance imaging KW - body limbs KW - swimming KW - lizards KW - deserts Y1 - 2008 U6 - https://doi.org/10.1371/journal.pone.0003309 SN - 1932-6203 VL - 3 IS - 10 PB - Plos CY - San Francisco, California, US ER - TY - CHAP A1 - Finkenberger, Isabel Maria ED - Büscher, Barbara ED - Krasny, Elke ED - Ortmann, Lucie T1 - Transformatives Handeln als disziplinüberschreitende, kollektive Aktion. Stadtentwicklung trifft künstlerische und kollaborative Handlungspraxen T2 - Porös-Werden : geteilte Räume, urbane Dramaturgien, performatives Kuratieren Y1 - 2024 SN - 978-3-98514-543-0 SP - 144 EP - 158 PB - Turia + Kant CY - Wien ER - TY - CHAP A1 - Kraft, Bodo A1 - Kohl, Philipp A1 - Meinecke, Matthias ED - Bernert, Christian ED - Scheurer, Steffen ED - Wehnes, Harald T1 - Analyse und Nachverfolgung von Projektzielen durch Einsatz von Natural Language Processing T2 - KI in der Projektwirtschaft : was verändert sich durch KI im Projektmanagement? Y1 - 2024 SN - 978-3-3811-1132-9 (Online) SN - 978-3-3811-1131-2 (Print) U6 - https://doi.org/10.24053/9783381111329 SP - 157 EP - 167 PB - UVK Verlag ER - TY - THES A1 - Latz, Annika T1 - Konzeptentwicklung einer spielerischen Lernanwendung für Studierende N2 - Ziel der Arbeit war es eine spielerische Lernanwendung für Studierende der FH-Aachen zu entwickeln, um das individuelle Lernen zu fördern. Dabei lag der Fokus auf der Konzeptentwicklung eines Serious Games für die Fachhochschule Aachen. Abgeleitet von Motivationstheorien, Game Design Frameworks und Eigenschaften von digitalen spielerischen Konzepten wurde ein Vorgehensmodell zur Konzeptentwicklung eines Serious Games erstellt. Wichtige Punkte für die Anwendung waren eine intensive Austauschmöglichkeiten für Studierende und das Integrieren dieser in die Lehrveranstaltungen der FH-Aachen. In der abschließenden Evaluation wurde positives Feedback der Studierenden eingeholt und damit das Ziel der Arbeit erreicht. Zusätzlich wurde für das erarbeitete Konzept die Wirtschaftlichkeit überprüft. Dafür wurde während der Bearbeitungszeit mit einem aufgestellten Team ein Business Plan für das Förderprogramm Start-Up transfer.NRW entwickelt. KW - Serious Game KW - Digitale Lehre KW - Digital Game Based Learning KW - Education KW - Gamification Y1 - 2021 ER - TY - JOUR A1 - Hoffstadt, Kevin A1 - Nikolausz, Marcell A1 - Krafft, Simone A1 - Bonatelli, Maria A1 - Kumar, Vivekanantha A1 - Harms, Hauke A1 - Kuperjans, Isabel T1 - Optimization of the ex situ biomethanation of hydrogen and carbon dioxide in a novel meandering plug flow reactor: start-up phase and flexible operation JF - Bioengineering KW - methanation KW - plug flow reactor KW - bubble column KW - biomethane KW - P2G Y1 - 2024 U6 - https://doi.org/10.3390/bioengineering11020165 SN - 2306-5354 VL - 11 IS - 2 PB - MDPI CY - Basel ER - TY - JOUR A1 - Frauenrath, Tobias A1 - Hezel, Fabian A1 - Heinrichs, Uwe A1 - Kozerke, Sebastian A1 - Utting, Jane A1 - Kob, Malte A1 - Butenweg, Christoph A1 - Boesiger, Peter A1 - Niendorf, Thoralf T1 - Feasibility of Cardiac Gating Free of Interference With Electro-Magnetic Fields at 1.5 Tesla, 3.0 Tesla and 7.0 Tesla Using an MR-Stethoscope JF - Investigative Radiology KW - phonocardiogram KW - electrocardiogram KW - cardiac gating KW - high field MR imaging KW - cardiovascular MR imaging Y1 - 2009 U6 - https://doi.org/10.1097/RLI.0b013e3181b4c15e SN - 1536-0210 (online) SN - 0020-9996 (gedruckt) VL - 44 IS - 9 SP - 539 EP - 547 PB - Lippincott Williams & Wilkins ; (via Ovid) CY - Philadelphia, Pa ER - TY - JOUR A1 - Uysal, Karya A1 - Firat, Ipek Serat A1 - Creutz, Till A1 - Aydin, Inci Cansu A1 - Artmann, Gerhard A1 - Teusch, Nicole A1 - Temiz Artmann, Aysegül T1 - A novel in vitro wound healing assay using free-standing, ultra-thin PDMS membranes JF - membranes N2 - Advances in polymer science have significantly increased polymer applications in life sciences. We report the use of free-standing, ultra-thin polydimethylsiloxane (PDMS) membranes, called CellDrum, as cell culture substrates for an in vitro wound model. Dermal fibroblast monolayers from 28- and 88-year-old donors were cultured on CellDrums. By using stainless steel balls, circular cell-free areas were created in the cell layer (wounding). Sinusoidal strain of 1 Hz, 5% strain, was applied to membranes for 30 min in 4 sessions. The gap circumference and closure rate of un-stretched samples (controls) and stretched samples were monitored over 4 days to investigate the effects of donor age and mechanical strain on wound closure. A significant decrease in gap circumference and an increase in gap closure rate were observed in trained samples from younger donors and control samples from older donors. In contrast, a significant decrease in gap closure rate and an increase in wound circumference were observed in the trained samples from older donors. Through these results, we propose the model of a cell monolayer on stretchable CellDrums as a practical tool for wound healing research. The combination of biomechanical cell loading in conjunction with analyses such as gene/protein expression seems promising beyond the scope published here. Y1 - 2022 U6 - https://doi.org/10.3390/membranes13010022 N1 - This article belongs to the Special Issue "Latest Scientific Discoveries in Polymer Membranes" VL - 2023 IS - 13(1) PB - MDPI CY - Basel ER - TY - JOUR A1 - Finkenberger, Isabel Maria T1 - Wohnen als Produktionsgemeinschaftsaufgabe JF - Jahrbuch für Christliche Sozialwissenschaften N2 - Wohnen als neue soziale Frage ist mehr als die Produktion neuer Formen von Wohnen und deren architektonischer Gestalt, und auch mehr als nur die Umsetzung sich verändernder, jedoch individuell formulierter Wohnwünsche. Sie spannt sich auf zwischen gesellschafts- und nachhaltigkeitspolitischen, hardcore-kapitalistischen und globalen Rahmenbedingungen, Hardware und Software, Individuum und Gemeinwohl, Konsum und Mitgestaltung. Entscheidend sind die Akteure und die Art und Weise, wie und nach welchen Maßstäben sie handeln. Entscheidend ist aber auch, Wohnen sowohl kontextuell wie auch programmatisch neu zu denken und dadurch zu neuen Mischungen, Nachbarschaften und Bewertungskriterien einer Projekt- und Stadtentwicklung zu kommen, die mehr als die Summe seiner Einzelteile wollen – ein gutes Leben für Alle abseits der Frage des Geldbeutels und der sozialen Zugehörigkeit. Y1 - 2024 U6 - https://doi.org/10.17879/jcsw-2021-3537 SN - 0075-2584 IS - 62 SP - 31 EP - 42 PB - Aschendorff CY - Münster ER - TY - CHAP A1 - Finkenberger, Isabel Maria T1 - Die Stadt als städtisch-theatrale Versuchsanordnung: Wie wollen wir in Zukunft leben und welche Stadt brauchen wir dafür? T2 - Un/Certain Futures - Rollen des Designs in gesellschaftlichen Transformationsprozessen Y1 - 2024 SN - 9783839443323 U6 - https://doi.org/https://doi.org/10.1515/9783839443323-009 SP - 86 EP - 95 PB - transcript CY - Bielefeld ER - TY - JOUR A1 - Finkenberger, Isabel Maria T1 - Strukturwandel als transformative Wende JF - disP: The Planning Review Y1 - 2024 U6 - https://doi.org/10.1080/02513625.2022.2158603 SN - 0251-3625 VL - 58 IS - 3 SP - 86 EP - 94 PB - Taylor & Francis CY - Abingdon ER - TY - CHAP A1 - Finkenberger, Isabel Maria ED - Pufke, Andrea T1 - Räumliche Transformation als Planungsaufgabe T2 - Zurück in die Zukunft. Denkmalpflege und Strukturwandel im Rheinischen Revier Y1 - 2024 N1 - Mitteilungen aus dem LVR-Amt für Denkmalpflege im Rheinland 39 : Zurück in die Zukunft. Denkmalpflege und Strukturwandel im Rheinischen Revier. Dokumentation zum 7. Rheinischen Tag für Denkmalpflege in Morschenich, 2. Juni 2022 SP - 70 EP - 77 PB - LVR-Amt für Denkmalpflege im Rheinland CY - Pulheim ER - TY - JOUR A1 - Finkenberger, Isabel Maria T1 - Transformatives Forschen, Lehren und Handeln im Rheinischen Braunkohlerevier JF - Forum Wohnen und Stadtentwicklung N2 - Die Institution Hochschule hat das Potenzial, über transformatives Forschen und Lehren und den entsprechenden Wissenstransfer in den lokalen Kontext strategisch-verlässliche Partnerin der Großen Transformation zur Nachhaltigkeit zu werden und bei der Ausbildung von Pionierinnen und Pionieren des Wandels mitzuwirken. Der Lehr- und Forschungsschwerpunkt „Zukunftsfähige Transformation” am Fachbereich Architektur der FH Aachen widmet sich seit 2020 dem Tagebauumfeld Hambach im Rheinischen Revier, um dort angewandt und in Kooperation neue Narrative, innovative Prozesse, ortsbezogene Konzepte und strategische Projekte zu entwickeln und umzusetzen. Y1 - 2024 SN - 1439-7242 VL - 2022 IS - 2 SP - 69 EP - 72 PB - vhw CY - Berlin ER - TY - JOUR A1 - Finkenberger, Isabel Maria A1 - Schlaich, Christoph T1 - Mehr als Wohnen. Vom Zusammenleben in integrierten Nachbarschaften JF - APuZ - Aus Politik und Zeitgeschichte N2 - Neue Dörfer braucht das Land! Dörfer in der Stadt und Dörfer auf dem Land (…). Die Planung und Gestaltung nachhaltiger Raumsysteme, die durch ein neues Verständnis des gemeinschaftlichen Besitzes (und dessen Nutzung) ressourcenfressende Individualisierungstendenzen unserer Gesellschaft überwinden, aber zugleich größtmöglichen Freiraum für eine individuelle Persönlichkeitsentfaltung zur Verfügung stellen." Dieses Zitat der Hamburger Initiative "Wir sind Dorf" beschreibt eine aktuelle Diskussion in unserer Gesellschaft, die sowohl in der Forschung und forschungsgeleiteten Initiativen, in Politik und Planung als auch in der Bürger-schaft stattfindet. Sie wird nicht nur auf wissenschaftlichen Veranstaltungen geführt, sondern auch in konkreten Projekten für integrative Lebenswelten, die Fragestellungen von Ernährung und Energieversorgung, von Arbeit und Ökonomie, aber auch eines neuen räumlichen und sozialen Miteinanders einbeziehen. Anders als bei den weit verbreiteten Baugruppen geht es nicht ausschließlich um die Schaffung von Wohnraum. Die Nachbarschaftsidee verbindet das Bedürfnis nach gemeinschaftlichem Wohnen und Wirtschaften mit einer neuen Werteorientierung, die auf persönlicher Verantwortungsübernahme beruht. Y1 - 2024 SN - 2194-3621 VL - 2014 IS - 20-21 SP - 46 EP - 52 PB - Bundeszentrale für politische Bildung - bpb CY - Bonn ER - TY - JOUR A1 - Finkenberger, Isabel Maria T1 - Vox populi. (Transformations-)potenziale nachkriegsmoderner Freiraumressourcen JF - Stadt+Grün N2 - Heute wie damals werden die großzügigen und offenen Siedlungsstrukturen der ersten Nachkriegsjahrzehnte mit ihrem hohen Anteil an "Grün" vielfach geschätzt und als solche nicht grundlegend hinterfragt. "Grün" verheißt im Allgemeinen Licht, Luft und Sonne, Freizeit und Erholung und gilt als etwas Wünschenswertes im städtischen Kontext. Unbeachtet bleibt, dass dem Begriff "Grün" zunächst keine Eigenschaften oder Qualitäten zugewiesen sind - er sagt noch lange nichts über dessen räumliche Qualität, dessen Nutzbarkeit, Erreichbarkeit und Zugänglichkeit aus. Abstandsgrün und Straßenbegleitgrün ist eben auch "Grün". Neben einer quantitativen Argumentation, welche ökologischen Aspekte wie Biotopvernetzung, Stadt- und Mikroklima berücksichtigt, sollten wir verstärkt qualitativ denken und damit die Grundlage für einen erweiterten und wesentlich differenzierteren Diskurs über urbane Freiräume ebnen. Y1 - 2024 SN - 0948-9770 VL - 2014 IS - 1 SP - 31 EP - 35 PB - Patzer CY - Berlin ER - TY - CHAP A1 - Finkenberger, Isabel Maria ED - Bredenbeck, Martin T1 - Vox populi. (Transformations-)potenziale nachkriegsmoderner Freiraumressourcen T2 - Grün modern - Gärten und Parks der 1950er bis 1970er Jahre Y1 - 2024 SN - 9783925374357 N1 - Ein Kulturerbe als Herausforderung für Denkmalpflege und Vermittlungsarbeit ; Dokumentation der Tagung am 15. und 16. Oktober 2013 in Hamburg SP - 31 EP - 38 PB - BHU CY - Bonn ER - TY - CHAP A1 - Peterson, Leif Arne ED - Schlüter, Dominik T1 - Holzbau T2 - Wofür braucht man das eigentlich? Ein Handbuch für Mathematiklehrkräfte der Sekundarstufe I und II Y1 - 2021 SN - 978-3-7543-2606-0 SP - 21 EP - 23 PB - BoD CY - Norderstedt ER - TY - CHAP A1 - Duffner, Markus A1 - Uibel, Thomas A1 - Peterson, Leif Arne A1 - Moorkamp, Wilfried ED - Fouad, Nabil A. T1 - Cross Layers Light – Ein ressourceneffizientes und recyclebares Holz-Wandsystem T2 - Bauphysik Kalender 2023: Nachhaltigkeit N2 - Ein neues tragendes, lagenweise aufgebautes Holzbau-Wandsystem und seine ökonomische und statische Entwicklung werden vorgestellt. Randbedingungen wie Nachhaltigkeit, Ressourceneffizienz und eine beanspruchungsadaptive Konstruktionsweise sind für diese innovative Bauteilentwicklung von zentraler Bedeutung. Eine wesentliche Herausforderung ist die Herstellung der Verbindung der Lagen untereinander zu einem bauphysikalisch und statisch leistungsfähigen Wandsystem. Die Tragfähigkeit und Steifigkeit verschiedener Verbindungsvarianten wurden ebenso wie die Eigenschaften der Wandelemente analytisch, numerisch und experimentell untersucht. Y1 - 2023 SN - 9783433033890 (Print) SN - 9783433611289 (Online) U6 - https://doi.org/10.1002/9783433611289.ch13 SP - 483 EP - 501 PB - Ernst & Sohn CY - Berlin ER - TY - CHAP A1 - Moorkamp, Wilfried A1 - Peterson, Leif Arne A1 - Uibel, Thomas ED - Fouad, Nabil A. T1 - Nachhaltige Holzbrücken für Geh- und Radwege T2 - Bauphysik Kalender 2022: Holzbau, 22. Jahrgang N2 - Am Lehr- und Forschungsgebiet Holzbau der Fachhochschule Aachen wurden im Rahmen des Forschungsvorhabens „Nachhaltige Standardbrücken in Holzbauweise“ Standardtypen für Geh- und Radwegbrücken entwickelt. Die Brücken sind durch konsequente Umsetzungen von Maßnahmen des konstruktiven Holzschutzes für eine Nutzung von mehr als 80~Jahren konzipiert. Innovative Lösungen für Bauteile und Anschlüsse sowie Materialalternativen im Bereich des Belages und der Geländer ermöglichen eine wartungsarme Konstruktion und tragen somit zur Wirtschaftlichkeit und Nachhaltigkeit bei. Um den Einsatz der entwickelten Standardbrückentypen in der Praxis zu erleichtern, wurden Leistungsverzeichnisse, Musterstatiken, Musterzeichnungen und umfangreiche Detailkataloge als Unterstützung für Planer und Bauherren erstellt. Damit die Randbedingungen für eine lange Lebensdauer während der Nutzung der Brücke erhalten bleiben, wurden Leitfäden für die Pflege und Wartung sowie für die Brückenprüfung erarbeitet. Der Beitrag gibt Einblicke in das Forschungsvorhaben und seine Resultate. Y1 - 2022 SN - 9783433033609 (Print) SN - 9783433611081 (Online) U6 - https://doi.org/10.1002/9783433611081.ch17 SP - 574 EP - 592 PB - Ernst & Sohn CY - Berlin ER - TY - CHAP A1 - Moorkamp, Wilfried A1 - Peterson, Leif Arne A1 - Uibel, Thomas ED - Wehren, Cedric T1 - Standardholzbrücken für kommunale Geh- und Radwege T2 - Strukturen, Formen und Prinzipien : Festschrift zum 60. Geburtstag von Univ.-Prof. Dr.-Ing. Martin Trautz Y1 - 2023 SN - 978-3-95886-500-6 SP - 140 EP - 165 PB - RWTH Aachen CY - Aachen ER - TY - JOUR A1 - Peterson-Oster, Madeleine A1 - Peterson, Leif Arne T1 - Gewerbebau: Modellprojekt mit neuem elementiertem, freistehendem Fassadensystem JF - Bauen mit Holz, Der Zimmermann N2 - Die im Zuge einer Betriebsübergabe anstehende Baumaßnahmen am eigenen Büro- und Produktionsgebäude boten ideale Voraussetzung zur Anwendung einer raum­-kreierenden Außenhaut. Mit der elementierten, freistehenden Eichenholz-Fassade wurde ein bis dahin weitgehend funktionales Bauwerk substanzschonend und zugleich optisch ansprechender umgestaltet. Y1 - 2020 SN - 0005-6545 PB - Rudolf Müller CY - Köln ER - TY - BOOK A1 - Uibel, Thomas A1 - Peterson, Leif Arne ED - Uibel, Thomas ED - Peterson, Leif Arne T1 - Tagungsband Aachener Holzbautagung 2023 Y1 - 2023 SN - 2197-4489 PB - FH Aachen CY - Aachen ER - TY - BOOK A1 - Uibel, Thomas A1 - Peterson, Leif Arne ED - Uibel, Thomas ED - Peterson, Leif Arne T1 - Tagungsband Aachener Holzbautagung 2013 Y1 - 2013 SN - 2197-4489 PB - FH Aachen CY - Aachen ER - TY - BOOK A1 - Uibel, Thomas A1 - Peterson, Leif Arne ED - Uibel, Thomas ED - Peterson, Leif Arne T1 - Tagungsband Aachener Holzbautagung 2019 Y1 - 2019 SN - 2197-4489 PB - FH Aachen CY - Aachen ER - TY - JOUR A1 - Becker, Meike A1 - Frauenrath, Tobias A1 - Hezel, Fabian A1 - Krombach, Gabriele A. A1 - Kremer, Ute A1 - Koppers, Benedikt A1 - Butenweg, Christoph A1 - Goemmel, Andreas A1 - Utting, Jane F. A1 - Schulz-Menger, Jeanette A1 - Niendorf, Thoralf T1 - Comparison of left ventricular function assessment using phonocardiogram- and electrocardiogram-triggered 2D SSFP CINE MR imaging at 1.5 T and 3.0 T JF - European Radiology N2 - Objective: As high-field cardiac MRI (CMR) becomes more widespread the propensity of ECG to interference from electromagnetic fields (EMF) and to magneto-hydrodynamic (MHD) effects increases and with it the motivation for a CMR triggering alternative. This study explores the suitability of acoustic cardiac triggering (ACT) for left ventricular (LV) function assessment in healthy subjects (n=14). Methods: Quantitative analysis of 2D CINE steady-state free precession (SSFP) images was conducted to compare ACT’s performance with vector ECG (VCG). Endocardial border sharpness (EBS) was examined paralleled by quantitative LV function assessment. Results: Unlike VCG, ACT provided signal traces free of interference from EMF or MHD effects. In the case of correct Rwave recognition, VCG-triggered 2D CINE SSFP was immune to cardiac motion effects—even at 3.0 T. However, VCG-triggered 2D SSFP CINE imaging was prone to cardiac motion and EBS degradation if R-wave misregistration occurred. ACT-triggered acquisitions yielded LV parameters (end-diastolic volume (EDV), endsystolic volume (ESV), stroke volume (SV), ejection fraction (EF) and left ventricular mass (LVM)) comparable with those derived fromVCG-triggered acquisitions (1.5 T: ESVVCG=(56± 17) ml, EDVVCG=(151±32)ml, LVMVCG=(97±27) g, SVVCG=(94± 19)ml, EFVCG=(63±5)% cf. ESVACT= (56±18) ml, EDVACT=(147±36) ml, LVMACT=(102±29) g, SVACT=(91± 22) ml, EFACT=(62±6)%; 3.0 T: ESVVCG=(55±21) ml, EDVVCG=(151±32) ml, LVMVCG=(101±27) g, SVVCG=(96±15) ml, EFVCG=(65±7)% cf. ESVACT=(54±20) ml, EDVACT=(146±35) ml, LVMACT= (101±30) g, SVACT=(92±17) ml, EFACT=(64±6)%). Conclusions: ACT’s intrinsic insensitivity to interference from electromagnetic fields renders KW - Magnetic resonance imaging (MRI) KW - MR-stethoscope KW - Magnetic field strength KW - Left ventriular function KW - Cardiovascular MRI Y1 - 2010 U6 - https://doi.org/10.1007/s00330-009-1676-z SN - 1432-1084 (Onlineausgabe) SN - 0938-7994 (Druckausgabe) VL - 20 SP - 1344 EP - 1355 PB - Springer CY - Berlin ER - TY - JOUR A1 - Butenweg, Christoph A1 - Heuer, R. A1 - Wenk, T. T1 - Erdbebeningenieurwesen und Baudynamik T1 - Earthquake engineering and structural dynamics (editorial) JF - Bauingenieur Y1 - 2015 SN - 00056650 VL - 90 IS - 10 SP - S1 PB - VDI Fachmedien CY - Düsseldorf ER - TY - CHAP A1 - Lu, S. A1 - Beyer, K. A1 - Bosiljkov, V. A1 - Butenweg, Christoph A1 - D’Ayala, D. A1 - Degee, H. A1 - Gams, M. A1 - Klouda, J. A1 - Lagomarsino, S. A1 - Penna, A. A1 - Mojsilovic, N. A1 - da Porto, F. A1 - Sorrentino, L. A1 - Vintzileou, E. ED - Modena, Claudio ED - da Porto, F. ED - Valluzzi, M.R. T1 - Next generation of Eurocode 8, masonry chapter T2 - Brick and Block Masonry Proceedings of the 16th International Brick and Block Masonry Conference, Padova, Italy, 26-30 June 2016 N2 - This paper describes the procedure on the evaluation of the masonry chapter for the next generation of Eurocode 8, the European Standard for earthquake-resistant design. In CEN, TC 250/SC8, working group WG 1 has been established to support the subcommittee on the topic of masonry on both design of new structures (EN1998-1) and assessment of existing structures (EN1998-3). The aim is to elaborate suggestions for amendments which fit the current state of the art in masonry and earthquake-resistant design. Focus will be on modelling, simplified methods, linear-analysis (q-values, overstrength-values), nonlinear procedures, out-of-plane design as well as on clearer definition of limit states. Beside these, topics related to general material properties, reinforced masonry, confined masonry, mixed structures and non-structural infills will be covered too. This paper presents the preliminary work and results up to the submission date. Y1 - 2016 SN - 978-1-138-02999-6 (Print) SN - 9781315374963 (E-Book) SP - 695 EP - 700 PB - Taylor & Francis CY - London ER - TY - JOUR A1 - Giresini, Linda A1 - Sassu, Mauro A1 - Butenweg, Christoph A1 - Alecci, Valerio A1 - De Stefano, Mario T1 - Vault macro-element with equivalent trusses in global seismic analyses JF - Earthquakes and Structures N2 - This paper proposes a quick and simplified method to describe masonry vaults in global seismic analyses of buildings. An equivalent macro-element constituted by a set of six trusses, two for each transverse, longitudinal and diagonal direction, is introduced. The equivalent trusses, whose stiffness is calculated by fully modeled vaults of different geometry, mechanical properties and boundary conditions, simulate the vault in both global analysis and local analysis, such as kinematic or rocking approaches. A parametric study was carried out to investigate the influence of geometrical characteristics and mechanical features on the equivalent stiffness values. The method was numerically validated by performing modal and transient analysis on a three naves-church in the elastic range. Vibration modes and displacement time-histories were compared showing satisfying agreement between the complete and the simplified models. This procedure is particularly useful in engineering practice because it allows to assess, in a simplified way, the effectiveness of strengthening interventions for reducing horizontal relative displacements between vault supports. KW - vault KW - macro-element KW - equivalent stiffness KW - truss KW - churches Y1 - 2017 U6 - https://doi.org/10.12989/eas.2017.12.4.409 SN - 2092-7614 (Print) SN - 2092-7622 (Online) VL - 12 IS - 4 SP - 409 EP - 423 PB - Techno-Press CY - Taejŏn ER - TY - JOUR A1 - Marinkovic, Marko A1 - Butenweg, Christoph T1 - Numerical analysis of the in-plane behaviour of decoupled masonry infilled RC frames JF - Engineering Structures N2 - Damage of reinforced concrete (RC) frames with masonry infill walls has been observed after many earthquakes. Brittle behaviour of the masonry infills in combination with the ductile behaviour of the RC frames makes infill walls prone to damage during earthquakes. Interstory deformations lead to an interaction between the infill and the RC frame, which affects the structural response. The result of this interaction is significant damage to the infill wall and sometimes to the surrounding structural system too. In most design codes, infill walls are considered as non-structural elements and neglected in the design process, because taking into account the infills and considering the interaction between frame and infill in software packages can be complicated and impractical. A good way to avoid negative aspects arising from this behavior is to ensure no or low-interaction of the frame and infill wall, for instance by decoupling the infill from the frame. This paper presents the numerical study performed to investigate new connection system called INODIS (Innovative Decoupled Infill System) for decoupling infill walls from surrounding frame with the aim to postpone infill activation to high interstory drifts thus reducing infill/frame interaction and minimizing damage to both infills and frames. The experimental results are first used for calibration and validation of the numerical model, which is then employed for investigating the influence of the material parameters as well as infill’s and frame’s geometry on the in-plane behaviour of the infilled frames with the INODIS system. For all the investigated situations, simulation results show significant improvements in behaviour for decoupled infilled RC frames in comparison to the traditionally infilled frames. KW - Seismic loading KW - Earthquake KW - In-plane performance, isolation KW - Infill wall design KW - Numerical modelling Y1 - 2022 U6 - https://doi.org/10.1016/j.engstruct.2022.114959 SN - 0141-0296 VL - 272 IS - 1 PB - Elsevier CY - Amsterdam ER - TY - BOOK A1 - Tünnemann, Thomas T1 - Formine 2023 : Concezione II N2 - Der diesjährige Workshop steht im Zeichen der räumlichen Konzeption. Das Erfahren und Definieren des engsten, ganz eigenen Betrachtungsraums, bis hin zur weitläufigen öffentlichen Umgebung des Ortes ist hierbei der erste Schritt. Hierzu stehen alle konzeptionellen Werkzeuge – von der Entwicklung vereinzelter Skizzenabfolgen, bis hin zur Collage - in den ersten Tagen des Workshops zur Verfügung. All diese Überlegungen, Konzepte und Entwürfe werden in eine Plastik überführt. Y1 - 2023 SN - 978-3-9811003-2-7 PB - FH Aachen, Fachbereich Architektur CY - Aachen ER - TY - BOOK A1 - Drumm, Christian A1 - Scheuermann, Bernd A1 - Weidner, Stefan T1 - Introduction to SAP S/4HANA® : The official companion book based on model company Global Bike–for learning, teaching, and training N2 - This easy-to-understand introduction to SAP S/4HANA guides you through the central processes in sales, purchasing and procurement, finance, production, and warehouse management using the model company Global Bike. Familiarize yourself with the basics of business administration, the relevant organizational data, master data, and transactional data, as well as a selection of core business processes in SAP. Using practical examples and tutorials, you will soon become an SAP S/4HANA professional! Tutorials and exercises for beginners, advanced users, and experts make it easy for you to practice your new knowledge. The prerequisite for this book is access to an SAP S/4HANA client with Global Bike version 4.1. - Business fundamentals and processes in the SAP system - Sales, purchasing and procurement, production, finance, and warehouse management - Tutorials at different qualification levels, exercises, and recap of case studies - Includes extensive download material for students, lecturers, and professors Y1 - 2024 SN - 9783960122685 PB - Espresso Tutorials CY - Gleichen ER - TY - CHAP A1 - Tepecik, Atakan ED - Digel, Ilya ED - Staat, Manfred ED - Trzewik, Jürgen ED - Sielemann, Stefanie ED - Erni, Daniel ED - Zylka, Waldemar T1 - AstroBioLab: Review of technical and bioanalytical approaches T2 - YRA MedTech Symposium (2024) N2 - This study presents the concept of AstroBioLab, an autonomous astrobiological field laboratory tailored for the exploration of (sub)glacial habitats. AstroBioLab is an integral component of the TRIPLE (Technologies for Rapid Ice Penetration and subglacial Lake Exploration) DLR-funded project, aimed at advancing astrobiology research through the development and deployment of innovative technologies. AstroBioLab integrates diverse measurement techniques such as fluorescence microscopy, DNA sequencing and fluorescence spectrometry, while leveraging microfluidics for efficient sample delivery and preparation. Y1 - 2024 SN - 978-3-940402-65-3 U6 - https://doi.org/10.17185/duepublico/81475 N1 - 4th YRA MedTech Symposium, February 1, 2024. FH Aachen, Campus Jülich SP - 33 EP - 34 PB - Universität Duisburg-Essen CY - Duisburg ER - TY - CHAP A1 - Sherelkhan, Dinara A1 - Alibekova, Alina ED - Digel, Ilya ED - Staat, Manfred ED - Trzewik, Jürgen ED - Sielemann, Stefanie ED - Erni, Daniel ED - Zylka, Waldemar T1 - EEM spectroscopy characterization of humic substances of biomedical importance T2 - YRA MedTech Symposium (2024) N2 - Humic substances possess distinctive chemical features enabling their use in many advanced applications, including biomedical fields. No chemicals in nature have the same combination of specific chemical and biological properties as humic substances. Traditional medicine and modern research have demonstrated that humic substances from different sources possess immunomodulatory and anti-inflammatory properties, which makes them suitable for the prevention and treatment of chronic dermatoses, allergic rhinitis, atopic dermatitis, and other conditions characterized by inflammatory and allergic responses [1-4]. The use of humic compounds as agentswith antifungal and antiviral properties shows great potential [5-7]. Y1 - 2024 SN - 978-3-940402-65-3 U6 - https://doi.org/10.17185/duepublico/81475 N1 - 4th YRA MedTech Symposium, February 1, 2024. FH Aachen, Campus Jülich SP - 31 EP - 32 PB - Universität Duisburg-Essen CY - Duisburg ER - TY - CHAP A1 - Schmitz, Annika A1 - Apandi, Shah Eiman Amzar Shah A1 - Spillner, Jan A1 - Hima, Flutura A1 - Behbahani, Mehdi ED - Digel, Ilya ED - Staat, Manfred ED - Trzewik, Jürgen ED - Sielemann, Stefanie ED - Erni, Daniel ED - Zylka, Waldemar T1 - Effect of different cannula positions in the pulmonary artery on blood flow and gas exchange using computational fluid dynamics analysis T2 - YRA MedTech Symposium (2024) N2 - Pulmonary arterial cannulation is a common and effective method for percutaneous mechanical circulatory support for concurrent right heart and respiratory failure [1]. However, limited data exists to what effect the positioning of the cannula has on the oxygen perfusion throughout the pulmonary artery (PA). This study aims to evaluate, using computational fluid dynamics (CFD), the effect of different cannula positions in the PA with respect to the oxygenation of the different branching vessels in order for an optimal cannula position to be determined. The four chosen different positions (see Fig. 1) of the cannulas are, in the lower part of the main pulmonary artery (MPA), in the MPA at the junction between the right pulmonary artery (RPA) and the left pulmonary artery (LPA), in the RPA at the first branch of the RPA and in the LPA at the first branch of the LPA. Y1 - 2024 SN - 978-3-940402-65-3 U6 - https://doi.org/10.17185/duepublico/81475 N1 - 4th YRA MedTech Symposium, February 1, 2024. FH Aachen, Campus Jülich SP - 29 EP - 30 PB - Universität Duisburg-Essen CY - Duisburg ER - TY - CHAP A1 - Simsek, Beril A1 - Krause, Hans-Joachim A1 - Engelmann, Ulrich M. ED - Digel, Ilya ED - Staat, Manfred ED - Trzewik, Jürgen ED - Sielemann, Stefanie ED - Erni, Daniel ED - Zylka, Waldemar T1 - Magnetic biosensing with magnetic nanoparticles: Simulative approach to predict signal intensity in frequency mixing magnetic detection T2 - YRA MedTech Symposium (2024) N2 - Magnetic nanoparticles (MNP) are investigated with great interest for biomedical applications in diagnostics (e.g. imaging: magnetic particle imaging (MPI)), therapeutics (e.g. hyperthermia: magnetic fluid hyperthermia (MFH)) and multi-purpose biosensing (e.g. magnetic immunoassays (MIA)). What all of these applications have in common is that they are based on the unique magnetic relaxation mechanisms of MNP in an alternating magnetic field (AMF). While MFH and MPI are currently the most prominent examples of biomedical applications, here we present results on the relatively new biosensing application of frequency mixing magnetic detection (FMMD) from a simulation perspective. In general, we ask how the key parameters of MNP (core size and magnetic anisotropy) affect the FMMD signal: by varying the core size, we investigate the effect of the magnetic volume per MNP; and by changing the effective magnetic anisotropy, we study the MNPs’ flexibility to leave its preferred magnetization direction. From this, we predict the most effective combination of MNP core size and magnetic anisotropy for maximum signal generation. Y1 - 2024 SN - 978-3-940402-65-3 U6 - https://doi.org/10.17185/duepublico/81475 N1 - 4th YRA MedTech Symposium, February 1, 2024. FH Aachen, Campus Jülich SP - 27 EP - 28 PB - Universität Duisburg-Essen CY - Duisburg ER - TY - BOOK A1 - Staat, Manfred A1 - Digel, Ilya A1 - Trzewik, Jürgen A1 - Sielemann, Stefanie A1 - Erni, Daniel A1 - Zylka, Waldemar T1 - Symposium Proceedings; 4th YRA MedTech Symposium 2024 : February 1 / 2024 / FH Aachen Y1 - 2024 SN - 978-3-940402-65-3 U6 - https://doi.org/10.17185/duepublico/81475 PB - Universität Duisburg-Essen CY - Duisburg ER - TY - THES A1 - Middelkoop, Jonas T1 - Frieden und Verschwörung : ein kritischer Dokumentarfilm über Daniele Ganser N2 - Im Umgang mit dem Schweizer Historiker Daniele Ganser lässt sich ein ungewöhnliches Phänomen beobachten. Während die Vorträge und Bücher des bekannten Publizisten bei zahlreichen Fans auf großes Interesse stoßen, zeichnen die meisten Medien das Bild eines gefährlichen Verschwörungstheoretikers. Schnell wird seine Person zum Symbolbild einer ganzen Gegenöffentlichkeit. Ein Dokumentarfilm über Daniele Ganser, seine Kritiker:innen und alternative Medien. KW - Dokumentarfilm KW - Daniele Ganser KW - Verschwörungstheorien KW - Medien KW - Philipp Hübl Y1 - 2023 PB - FH Aachen CY - Aachen ER - TY - THES A1 - Philippen, Jule T1 - bond(ed) : ein Projekt zum Kontaktabbruch in Familien N2 - Eines haben wir alle gemeinsam – Eine Familie. Die Bachelorarbeit „bond(ed)“ ist ein Projekt zum Kontaktabbruch in Familien. Familiäre Kontaktabbrüche sind heute keine Seltenheit mehr. Jede:r kennt jemanden, der davon betroffen ist, und doch wird nur selten darüber gesprochen. Schamgefühl, Angst und das Gefühl von Versagen spielen hierbei eine entscheidende Rolle. Doch wie kann es so weit kommen? Neun Personen haben sich bereit erklärt, ihre sehr persönlichen und emotionalen Geschichten zu teilen. Im Zuge dessen sind Fotos im jeweiligen Zuhause und in Interviewform niedergeschriebene Gespräche entstanden, welche unabhängig voneinander in zwei Büchern zu betrachten sind. Das Projekt „bond(ed)“ soll familiären Kontaktabbrüchen eine Plattform bieten und mit einem Tabuthema brechen. Es soll mit Vorurteilen aufräumen und ein Gefühl von Zusammengehörigkeit bei den Betroffenen wecken. KW - Familie KW - Kontaktabbruch KW - Fotografie KW - Interview KW - Menschen Y1 - 2023 PB - FH Aachen CY - Aachen ER - TY - THES A1 - Vetter, Cara Niambi T1 - BRIDGE - Ein Magazin über Transkulturen in Deutschland BT - Ausgabe 1: Deutsch-Habesha-Kultur N2 - In Folge der Globalisierung und der Zuwanderung von verschiedensten ethnischen Gruppen und deren Kulturen entstehen in Deutschland immer mehr sogenannte Transkulturen. Um diesen mehr Aufmerksamkeit zu schenken und zur Verständigung verschiedenster Gruppen beizutragen, wurde das Konzept dieser Bachelorarbeit: „BRIDGE: Ein Magazin über Transkulturen in Deutschland" entwickelt, welches sich mit den Schnittstellen der Deutschen und anderen Kulturen auseinandersetzt. Diese Transkulturen sollen jeweils repräsentativ und aufklärend dargestellt werden. Jede Ausgabe wird eine dieser Transkulturen porträtieren und zeigen, wie diese in Deutschland besteht. Für die erste Ausgabe, welche im Rahmen der Bachelorarbeit ausgearbeitet wurde, fiel die Entscheidung auf die Deutsch-Habesha-Kultur, die eine Völkergruppe aus Äthiopien und Eritrea darstellt. KW - Editorial KW - Magazin KW - Fotografie KW - Transkulturen KW - Aufklärung Y1 - 2023 PB - FH Aachen CY - Aachen ER - TY - THES A1 - Von Dallwitz, Sophia T1 - (un)said : Offene Gespräche über Alltagssexismus N2 - Unsaid ist ein didaktisches Starterkit für offene Gespräche über Alltagssexismus mit einem Schwerpunkt auf sexueller Belästigung im öffentlichen Raum. Es beinhaltet mehrere Schritte – die Broschüre bietet euch das benötigte Wissen für einen konstruktiven Diskurs. Zusätzlich sind Karten mit Fragen enthalten, die dazu anregen, sexistische Denkmuster und Verhaltensweisen im Alltag zu erkennen und zu reflektieren. Und schließlich zeigt es konkrete Aktionen auf, wie ihr selbst aktiv werden und euch gegen sexistisches Verhalten aussprechen könnt. Das Kit ist darauf ausgerichtet, dass Lehrende an weiterführenden Schulen es in ihren Unterricht integrieren können. Ihr könnt es jedoch genauso gut unter euren Freund*innen, Kolleg*innen oder anderen Interessierten nutzen, um eure Meinungen und Erfahrungen miteinander zu teilen. Unsaid ist ein weiterer Schritt, um Alltagssexismus zu bekämpfen und eine Gesellschaft zu schaffen, in der Gleichberechtigung und Respekt selbstverständlich sind. KW - Typografie KW - Starterkit KW - Broschüre KW - Leitfaden KW - Diskussionskarten Y1 - 2023 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER - TY - THES A1 - Waliszewska, Laura T1 - Werkstatt voller Historie N2 - Das Buch „Werkstatt voller Historie“ gibt einen Einblick in das Handwerk der Restaurierung und Konservierung. Wir leben in einer Gesellschaft, die von Konsum und schneller Verfügbarkeit geprägt ist. Produkte werden in Massen produziert, genutzt und oft schon nach kurzer Zeit wieder weggeworfen. Durch diese Mentalität der Wegwerfgesellschaft werden die Ressourcen unserer Erde erschöpft, und Umweltprobleme werden immer größer. Deshalb ist es wichtig, sich intensiv mit der Bewahrung von Kulturgut auseinanderzusetzen. Durch die Verwendung von Illustrationen und visuellen Darstellungen erleichtert das Buch die Kommunikation. Dadurch kann der Restaurierungsprozess einfacher verstanden werden. Mit dem Projekt soll das Interesse geweckt und über die Grundlagen und Herausforderungen der Restaurierung aufgeklärt werden. KW - Restaurierung KW - Konservierung KW - Werkstatt KW - Historie KW - Handwerk Y1 - 2023 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER - TY - THES A1 - Wamper, Lukas T1 - Bachelorzeit N2 - Die Bachelorarbeit behandelt die Konzeption und Produktion der Sendung "Bachelorzeit". Ziel ist es, eine innovative Plattform für junge Zuschauer:innen zu schaffen und Einblicke in das Leben und die Themen der Stadt Aachen zu geben. Die Arbeit umfasst den gesamten Produktionsprozess inklusive der Einbindung der Zuschauer:innen und der visuellen Gestaltung. Die erfolgreiche Umsetzung ermöglicht eine ansprechende und nahbare Atmosphäre für ein jüngeres Publikum. KW - Visuelle Gestaltung KW - Sendungskonzeption KW - Produktion KW - Innovation KW - Stadt Aachen Y1 - 2023 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER - TY - THES A1 - Begas, Philipp T1 - Modulares Regalsystem : Stauraummöbel für den Bereich Office / Homeoffice N2 - Das modulare Regalsystem „MORÉ“ ist ein Stauraummöbel, welches sich im Bereich des (Home) Office einordnet. Das Produkt dient zur Aufbewahrung von Büromaterialien und verbessert die Geräuschkulisse sowie die Beschaffenheit am Arbeitsplatz. Die potenzielle Käufergruppe befindet sich im Alter von 25-67 Jahren, im gewöhnlichen Arbeitsalter Zeitraum (obere Mittelschicht). Im Fokus des Regalsystems steht der besonders freundliche Auf- und Abbau, welcher werkzeuglos erfolgt. Es ist in verschiedene Richtungen erweiterbar (Steckverbindung) und bietet unendlichen Spielraum der Gestaltung. Durch verschiedenfarbige Kennzeichnungen bietet das Regal ein Ordnungssystem, wodurch schnelleres Finden und Sortieren von Unterlagen möglich ist (Grundordnung). Die Rückwände dienen neben der Stabilität als Akustik-/ und Sichtschutz. Das Produkt passt sich jeder Raumsituation individuell an. Ist „MORÉ“ dein nächstes Regalsystem? KW - Modular KW - Steckverbindung KW - Office KW - Erweiterbar KW - Benutzerfreundlich Y1 - 2023 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER - TY - THES A1 - Behrmann, Wieka T1 - GLOW UP. : eine multifunktionale Kinderleuchte zur Förderung der Selbstständigkeit N2 - Durch die Kombination von Merkmalen verschiedener Leuchtentypen erfüllt Glow up eine Vielzahl von Bedürfnissen in unterschiedlichsten Szenarien. Bei einer Nachtwanderung erhellt sie den Weg oder sie spendet Geborgenheit, wenn Kinder sich vor der Dunkelheit beim Einschlafen fürchten. Die Anpassbarkeit der Leuchte steht im Mittelpunkt und ermöglicht die Einstellung von Helligkeit und Lichttemperatur sowie den Wechsel zwischen direktem und indirektem Licht. Mit einer Vielzahl von Befestigungsmöglichkeiten, auswechselbaren Leuchtenschirmen und kindgerechtem Design ist "Glow up" ein wahres Multitalent und ein enger Begleiter im Alltag. KW - Kind KW - Lampe KW - Leuchte KW - nachhaltig KW - Licht Y1 - 2023 PB - FH Aachen CY - Aachen ER - TY - THES A1 - Shah, Akshat T1 - Vita : Rehabilitation assistance for digital professionals N2 - Vita ist ein Produkt zur Unterstützung von Physiotherapie und Rehabilitation für moderne digitale Profis. Es hilft beim Aufspüren und Erkennen von Haltungsfehlern und gibt positives und sinnvolles Feedback. Ziel des Feedbacks ist es, ein Gefühl des Vertrauens in den Genesungsprozess zu schaffen und durch die Nachahmung der menschlichen Berührung neue, positive Haltungsgewohnheiten zu entwickeln und zu kultivieren. KW - Haltung KW - Positives Feedback KW - Industriedesign KW - Rehabilitaion KW - Digital Y1 - 2023 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER - TY - JOUR A1 - Koch, Christopher A1 - Böhnisch, Nils A1 - Verdonck, Hendrik A1 - Hach, Oliver A1 - Braun, Carsten T1 - Comparison of unsteady low- and mid-fidelity propeller aerodynamic methods for whirl flutter applications JF - Applied Sciences N2 - Aircraft configurations with propellers have been drawing more attention in recent times, partly due to new propulsion concepts based on hydrogen fuel cells and electric motors. These configurations are prone to whirl flutter, which is an aeroelastic instability affecting airframes with elastically supported propellers. It commonly needs to be mitigated already during the design phase of such configurations, requiring, among other things, unsteady aerodynamic transfer functions for the propeller. However, no comprehensive assessment of unsteady propeller aerodynamics for aeroelastic analysis is available in the literature. This paper provides a detailed comparison of nine different low- to mid-fidelity aerodynamic methods, demonstrating their impact on linear, unsteady aerodynamics, as well as whirl flutter stability prediction. Quasi-steady and unsteady methods for blade lift with or without coupling to blade element momentum theory are evaluated and compared to mid-fidelity potential flow solvers (UPM and DUST) and classical, derivative-based methods. Time-domain identification of frequency-domain transfer functions for the unsteady propeller hub loads is used to compare the different methods. Predictions of the minimum required pylon stiffness for stability show good agreement among the mid-fidelity methods. The differences in the stability predictions for the low-fidelity methods are higher. Most methods studied yield a more unstable system than classical, derivative-based whirl flutter analysis, indicating that the use of more sophisticated aerodynamic modeling techniques might be required for accurate whirl flutter prediction. KW - Aeroelasticity KW - Flutter KW - Propeller whirl flutter KW - Unsteady aerodynamics KW - 1P hub loads Y1 - 2024 U6 - https://doi.org/10.3390/app14020850 SN - 2076-3417 VL - 14 IS - 2 SP - 1 EP - 28 PB - MDPI CY - Basel ER - TY - THES A1 - Ferraioli, Luigi T1 - Validierung einer Simulationsumgebung für Umfeldsensorik von Schienenfahrzeugen N2 - Diese Bachelorarbeit befasst sich mit der digitalen Nachbildung eines Testgeländes sowie eines Schienenfahrzeugs in der Simulationsumgebung Gazebo. Der Schwerpunkt liegt auf der präzisen Abbildung der Umfeldsensorik anhand eines realen Schienenfahrzeuges. Ziel ist die Erzeugung äquivalenter Messdaten der Simulationsumgebung und des realen Schienenfahrzeuges unter gleichen Einsatzbedingungen. Dazu werden unterschiedliche Verfahren eingesetzt, um die Parameter der einzelnen Sensorik so zu konfigurieren, dass die Messergebnisse mit den Messdaten der realen Sensorik konvergieren. Die Ergebnisse der Messdaten zeigen, dass obwohl die Simulationsumgebung einige physikalische Materialeigenschaften nicht berücksichtigt, eine präzise Abbildung der Sensorik und geometrischen Strukturen des Testgeländes möglich ist. Darüber hinaus ermöglicht die Kombination von Gazebo und ROS2 Integrationstests und die Entwicklung von Softwareanwendungen sowohl in der Simulation als auch auf dem realen Schienenfahrzeug. Eine realitätsnahe und reproduzierbare Auswertung der Sensormessdaten der Simulationsumgebung für Schienenfahrzeuge ist somit realisierbar. Y1 - 2023 PB - FH Aachen CY - Aachen ER - TY - JOUR A1 - Bung, Daniel Bernhard A1 - Erpicum, Sébastien A1 - Tullis, Blanke P. T1 - Advances in hydraulic structures engineering JF - Journal of Hydraulic Engineering Y1 - 2020 U6 - https://doi.org/10.1061/(ASCE)HY.1943-7900.0001851 SN - 0733-9429 (Druckausgabe) SN - 1943-7900 (Online-Ausgabe) VL - 147 IS - 1 PB - ASCE CY - Reston, Va. ER - TY - JOUR A1 - von Häfen, Hajo A1 - Krautwald, Clemens A1 - Stolle, Jacob A1 - Bung, Daniel Bernhard A1 - Goseberg, Nils T1 - Overland flow of broken solitary waves over a two-dimensional coastal plane JF - Coastal Engineering N2 - Landslides, rock falls or related subaerial and subaqueous mass slides can generate devastating impulse waves in adjacent waterbodies. Such waves can occur in lakes and fjords, or due to glacier calving in bays or at steep ocean coastlines. Infrastructure and residential houses along coastlines of those waterbodies are often situated on low elevation terrain, and are potentially at risk from inundation. Impulse waves, running up a uniform slope and generating an overland flow over an initially dry adjacent horizontal plane, represent a frequently found scenario, which needs to be better understood for disaster planning and mitigation. This study presents a novel set of large-scale flume test focusing on solitary waves propagating over a 1:14.5 slope and breaking onto a horizontal section. Examining the characteristics of overland flow, this study gives, for the first time, insight into the fundamental process of overland flow of a broken solitary wave: its shape and celerity, as well as its momentum when wave breaking has taken place beforehand. KW - Landslide tsunamis KW - Hazard assessment KW - Large scale tests KW - Overland flow KW - Solitary waves Y1 - 2022 U6 - https://doi.org/10.1016/j.coastaleng.2022.104125 SN - 1872-7379 VL - 175 IS - August PB - Elsevier CY - Amsterdam ER - TY - INPR A1 - Ringers, Christa A1 - Bialonski, Stephan A1 - Solovev, Anton A1 - Hansen, Jan N. A1 - Ege, Mert A1 - Friedrich, Benjamin M. A1 - Jurisch-Yaksi, Nathalie T1 - Preprint: Local synchronization of cilia and tissue-scale cilia alignment are sufficient for global metachronal waves T2 - bioRxiv N2 - Motile cilia are hair-like cell extensions present in multiple organs of the body. How cilia coordinate their regular beat in multiciliated epithelia to move fluids remains insufficiently understood, particularly due to lack of rigorous quantification. We combine here experiments, novel analysis tools, and theory to address this knowledge gap. We investigate collective dynamics of cilia in the zebrafish nose, due to its conserved properties with other ciliated tissues and its superior accessibility for non-invasive imaging. We revealed that cilia are synchronized only locally and that the size of local synchronization domains increases with the viscosity of the surrounding medium. Despite the fact that synchronization is local only, we observed global patterns of traveling metachronal waves across the multiciliated epithelium. Intriguingly, these global wave direction patterns are conserved across individual fish, but different for left and right nose, unveiling a chiral asymmetry of metachronal coordination. To understand the implications of synchronization for fluid pumping, we used a computational model of a regular array of cilia. We found that local metachronal synchronization prevents steric collisions and improves fluid pumping in dense cilia carpets, but hardly affects the direction of fluid flow. In conclusion, we show that local synchronization together with tissue-scale cilia alignment are sufficient to generate metachronal wave patterns in multiciliated epithelia, which enhance their physiological function of fluid pumping. Y1 - 2021 U6 - https://doi.org/10.1101/2021.11.23.469646 N1 - Veröffentlicht in eLife 12:e77701 (https://doi.org/10.7554/eLife.77701). ER - TY - JOUR A1 - Yang, Peng-Fei A1 - Kriechbaumer, Andreas A1 - Albracht, Kirsten A1 - Sanno, Maximilian A1 - Ganse, Bergita A1 - Koy, Timmo A1 - Shang, Peng A1 - brüggemann, Gert-Peter A1 - Müller, Lars Peter A1 - Rittweger, Jörn T1 - A novel optical approach for assessing in vivo bone segment deformation and its application in muscle-bone relationship studies in humans JF - Journal of Orthopaedic Translation Y1 - 2014 U6 - https://doi.org/10.1016/j.jot.2014.07.078 SN - 2214-0328 SN - 2214-031X VL - 2 IS - 4 SP - 238 EP - 238 PB - Elsevier CY - Singapore ER - TY - JOUR A1 - Haeger, Gerrit A1 - Jolmes, Tristan A1 - Oyen, Sven A1 - Jaeger, Karl-Erich A1 - Bongaerts, Johannes A1 - Schörken, Ulrich A1 - Siegert, Petra T1 - Novel recombinant aminoacylase from Paraburkholderia monticola capable of N-acyl-amino acid synthesis JF - Applied Microbiology and Biotechnology N2 - N-Acyl-amino acids can act as mild biobased surfactants, which are used, e.g., in baby shampoos. However, their chemical synthesis needs acyl chlorides and does not meet sustainability criteria. Thus, the identification of biocatalysts to develop greener synthesis routes is desirable. We describe a novel aminoacylase from Paraburkholderia monticola DSM 100849 (PmAcy) which was identified, cloned, and evaluated for its N-acyl-amino acid synthesis potential. Soluble protein was obtained by expression in lactose autoinduction medium and co-expression of molecular chaperones GroEL/S. Strep-tag affinity purification enriched the enzyme 16-fold and yielded 15 mg pure enzyme from 100 mL of culture. Biochemical characterization revealed that PmAcy possesses beneficial traits for industrial application like high temperature and pH-stability. A heat activation of PmAcy was observed upon incubation at temperatures up to 80 °C. Hydrolytic activity of PmAcy was detected with several N-acyl-amino acids as substrates and exhibited the highest conversion rate of 773 U/mg with N-lauroyl-L-alanine at 75 °C. The enzyme preferred long-chain acyl-amino-acids and displayed hardly any activity with acetyl-amino acids. PmAcy was also capable of N-acyl-amino acid synthesis with good conversion rates. The best synthesis results were obtained with the cationic L-amino acids L-arginine and L-lysine as well as with L-leucine and L-phenylalanine. Exemplarily, L-phenylalanine was acylated with fatty acids of chain lengths from C8 to C18 with conversion rates of up to 75%. N-lauroyl-L-phenylalanine was purified by precipitation, and the structure of the reaction product was verified by LC–MS and NMR. KW - Chaperone KW - Biocatalysis KW - Aminoacylase KW - Acylation KW - Acyl-amino acids KW - Biosurfactants Y1 - 2024 U6 - https://doi.org/10.1007/s00253-023-12868-8 SN - 1432-0614 N1 - Corresponding author: Petra Siegert IS - 108 PB - Springer CY - Berlin ER - TY - JOUR A1 - Werkhausen, Amelie A1 - Albracht, Kirsten A1 - Cronin, Neil J A1 - Paulsen, Gøran A1 - Bojsen-Møller, Jens A1 - Seynnes, Olivier R T1 - Effect of training-induced changes in achilles tendon stiffness on muscle-tendon behavior during landing JF - Frontiers in physiology N2 - During rapid deceleration of the body, tendons buffer part of the elongation of the muscle-tendon unit (MTU), enabling safe energy dissipation via eccentric muscle contraction. Yet, the influence of changes in tendon stiffness within the physiological range upon these lengthening contractions is unknown. This study aimed to examine the effect of training-induced stiffening of the Achilles tendon on triceps surae muscle-tendon behavior during a landing task. Twenty-one male subjects were assigned to either a 10-week resistance-training program consisting of single-leg isometric plantarflexion (n = 11) or to a non-training control group (n = 10). Before and after the training period, plantarflexion force, peak Achilles tendon strain and stiffness were measured during isometric contractions, using a combination of dynamometry, ultrasound and kinematics data. Additionally, testing included a step-landing task, during which joint mechanics and lengths of gastrocnemius and soleus fascicles, Achilles tendon, and MTU were determined using synchronized ultrasound, kinematics and kinetics data collection. After training, plantarflexion strength and Achilles tendon stiffness increased (15 and 18%, respectively), and tendon strain during landing remained similar. Likewise, lengthening and negative work produced by the gastrocnemius MTU did not change detectably. However, in the training group, gastrocnemius fascicle length was offset (8%) to a longer length at touch down and, surprisingly, fascicle lengthening and velocity were reduced by 27 and 21%, respectively. These changes were not observed for soleus fascicles when accounting for variation in task execution between tests. These results indicate that a training-induced increase in tendon stiffness does not noticeably affect the buffering action of the tendon when the MTU is rapidly stretched. Reductions in gastrocnemius fascicle lengthening and lengthening velocity during landing occurred independently from tendon strain. Future studies are required to provide insight into the mechanisms underpinning these observations and their influence on energy dissipation. KW - achilles tendon KW - energy absorption KW - energy dissipation KW - mechanical buffer KW - stiffness Y1 - 2018 U6 - https://doi.org/10.3389/fphys.2018.00794 SN - 1664-042X IS - 9 PB - Frontiers Research Foundation CY - Lausanne ER - TY - JOUR A1 - Savitskaya, Irina A1 - Zhantlessova, Sirina A1 - Kistaubayeva, Aida A1 - Ignatova, Ludmila A1 - Shokatayeva, Dina A1 - Sinyavsky, Yuriy A1 - Kushugulova, Almagul A1 - Digel, Ilya T1 - Prebiotic cellulose–pullulan matrix as a “vehicle” for probiotic biofilm delivery to the host large intestine JF - Polymers N2 - This study describes the development of a new combined polysaccharide-matrix-based technology for the immobilization of Lactobacillus rhamnosus GG (LGG) bacteria in biofilm form. The new composition allows for delivering the bacteria to the digestive tract in a manner that improves their robustness compared with planktonic cells and released biofilm cells. Granules consisting of a polysaccharide matrix with probiotic biofilms (PMPB) with high cell density (>9 log CFU/g) were obtained by immobilization in the optimized nutrient medium. Successful probiotic loading was confirmed by fluorescence microscopy and scanning electron microscopy. The developed prebiotic polysaccharide matrix significantly enhanced LGG viability under acidic (pH 2.0) and bile salt (0.3%) stress conditions. Enzymatic extract of feces, mimicking colon fluid in terms of cellulase activity, was used to evaluate the intestinal release of probiotics. PMPB granules showed the ability to gradually release a large number of viable LGG cells in the model colon fluid. In vivo, the oral administration of PMPB granules in rats resulted in the successful release of probiotics in the colon environment. The biofilm-forming incubation method of immobilization on a complex polysaccharide matrix tested in this study has shown high efficacy and promising potential for the development of innovative biotechnologies. KW - immobilization KW - prebiotic KW - bacterial cellulose KW - biofilms KW - Lactobacillus rhamnosus GG Y1 - 2023 U6 - https://doi.org/10.3390/polym16010030 N1 - This article belongs to the Section "Polymer Composites and Nanocomposites" IS - 16(1) PB - MDPI CY - Basel ER - TY - CHAP A1 - Dreschers, Martin ED - Kübler, Bruno M. ED - Bork, Reinhard ED - Prütting, Hanns T1 - §18 Grenzüberschreitende Eigenverwaltung T2 - HRI II - Handbuch Restrukturierung in der Insolvenz Y1 - 2023 SN - 978-3-8145-2010-0 (print) SN - 978-3-8145-5871-4 (e-book) U6 - https://doi.org/10.15375/9783814558714-028 SP - 524 EP - 556 PB - RWS Verlag CY - Köln ER - TY - CHAP A1 - Dreschers, Martin ED - Mönning, Rolf-Dieter T1 - §25 Arbeitsrechtliche Probleme im Rahmen der Betriebsfortführung T2 - Betriebsfortführung in Restrukturierung und Insolvenz Y1 - 2023 SN - 978-3-8145-2012-4 (print) SN - 978-3-8145-5888-2 (e-book) U6 - https://doi.org/https://doi.org/10.15375/9783814558882-028 SP - 947 EP - 988 PB - RWS Verlag CY - Köln ER - TY - JOUR A1 - Ketelhut, Maike A1 - Göll, Fabian A1 - Braunstein, Björn A1 - Albracht, Kirsten A1 - Abel, Dirk T1 - Comparison of different training algorithms for the leg extension training with an industrial robot JF - Current Directions in Biomedical Engineering N2 - In the past, different training scenarios have been developed and implemented on robotic research platforms, but no systematic analysis and comparison have been done so far. This paper deals with the comparison of an isokinematic (motion with constant velocity) and an isotonic (motion against constant weight) training algorithm. Both algorithms are designed for a robotic research platform consisting of a 3D force plate and a high payload industrial robot, which allows leg extension training with arbitrary six-dimensional motion trajectories. In the isokinematic as well as the isotonic training algorithm, individual paths are defined i n C artesian s pace by sufficient s upport p oses. I n t he i sotonic t raining s cenario, the trajectory is adapted to the measured force as the robot should only move along the trajectory as long as the force applied by the user exceeds a minimum threshold. In the isotonic training scenario however, the robot’s acceleration is a function of the force applied by the user. To validate these findings, a simulative experiment with a simple linear trajectory is performed. For this purpose, the same force path is applied in both training scenarios. The results illustrate that the algorithms differ in the force dependent trajectory adaption. KW - Rehabilitation Technology and Prosthetics KW - Surgical Navigation and Robotics Y1 - 2018 U6 - https://doi.org/10.1515/cdbme-2018-0005 SN - 2364-5504 VL - 4 IS - 1 SP - 17 EP - 20 PB - De Gruyter CY - Berlin ER - TY - JOUR A1 - Werkhausen, Amelie A1 - Cronin, Neil J. A1 - Albracht, Kirsten A1 - Paulsen, Gøran A1 - Larsen, Askild V. A1 - Bojsen-Møller, Jens A1 - Seynnes, Olivier R. T1 - Training-induced increase in Achilles tendon stiffness affects tendon strain pattern during running JF - PeerJ N2 - Background During the stance phase of running, the elasticity of the Achilles tendon enables the utilisation of elastic energy and allows beneficial contractile conditions for the triceps surae muscles. However, the effect of changes in tendon mechanical properties induced by chronic loading is still poorly understood. We tested the hypothesis that a training-induced increase in Achilles tendon stiffness would result in reduced tendon strain during the stance phase of running, which would reduce fascicle strains in the triceps surae muscles, particularly in the mono-articular soleus. Methods Eleven subjects were assigned to a training group performing isometric singleleg plantarflexion contractions three times per week for ten weeks, and another ten subjects formed a control group. Before and after the training period, Achilles tendon stiffness was estimated, and muscle-tendon mechanics were assessed during running at preferred speed using ultrasonography, kinematics and kinetics. Results Achilles tendon stiffness increased by 18% (P <0:01) in the training group, but the associated reduction in strain seen during isometric contractions was not statistically significant. Tendon elongation during the stance phase of running was similar after training, but tendon recoil was reduced by 30% (P <0:01), while estimated tendon force remained unchanged. Neither gastrocnemius medialis nor soleus fascicle shortening during stance was affected by training. Discussion These results show that a training-induced increase in Achilles tendon stiffness altered tendon behaviour during running. Despite training-induced changes in tendon mechanical properties and recoil behaviour, the data suggest that fascicle shortening patterns were preserved for the running speed that we examined. The asymmetrical changes in tendon strain patterns supports the notion that simple inseries models do not fully explain the mechanical output of the muscle-tendon unit during a complex task like running. KW - Achilles tendon KW - Stiffness KW - Running KW - Tendon properties KW - Architectural gear ratio Y1 - 2019 U6 - https://doi.org/10.7717/peerj.6764 SN - 21678359 PB - Peer CY - London ER - TY - GEN A1 - Blottner, Dieter A1 - Hastermann, Maria A1 - Muckelt, Paul A1 - Albracht, Kirsten A1 - Schoenrock, Britt A1 - Salanova, Michele A1 - Warner, Martin A1 - Gunga, Hans-Christian A1 - Stokes, Maria T1 - MYOTONES - Inflight muscle health status monitoring during long-duration space missions onboard the International Space Station: a single case study T2 - IAC Papers Archive N2 - The MYOTONES experiment is the first to monitor changes in the basic biomechanical properties (tone, elasticity and stiffness) of the resting human myofascial system due to microgravity with a oninvasive, portable device on board the ISS. The MyotonPRO device applies several brief mechanical stimuli to the surface of the skin, and the natural oscillation signals of the tissue beneath are detected and computed by the MyotonPRO. Thus, an objective, quick and easy determination of the state of the underlying tissue is possible. Two preflight, four inflight and four post flight measurements were performed on a male astronaut using the same 10 measurement points (MP) for each session. MPs were located on the plantar fascia, Achilles tendon, M. soleus, M. gastrocnemius, M. multifidus, M. splenius capitis, M. deltoideus anterior, M. rectus femoris, infrapatellar tendon, M. tibialis anterior. Subcutaneous tissues thickness above the MPs was measured using ultrasound imaging. Magnetic resonance images (MRI) of lower limb muscles and functional tests were also performed pre- and postflight. Our first measurements on board the ISS confirmed increased tone and stiffness of the lumbar multifidus muscle, an important trunk stabilizer, dysfunction of which is known to be associated with back pain. Furthermore, reduced tone and stiffness of Achilles tendon and plantar fascia were observed inflight vs. preflight, confirming previous findings from terrestrial analog studies and parabolic flights. Unexpectedly, the deltoid showed negative inflight changes in tone and stiffness, and increased elasticity, suggesting a potential risk of muscle atrophy in longer spaceflight that should be addressed by adequate inflight countermeasure protocols. Most values from limb and back MPS showed deflected patterns (in either directions) from inflight shortly after the re-entry phase on the landing day and one week later. Most parameter values then normalized to baseline after 3 weeks likely due to 1G re-adaptation and possible outcome of the reconditioning protocol. No major changes in subcutaneous tissues thickness above the MPs were found inflight vs preflight, suggesting no bias (i.e., fluid shift, extreme tissue thickening or loss). Pre- and postflight MRI and functional tests showed negligible changes in calf muscle size, power and force, which is likely due to training effects from current inflight exercise protocols. The MYOTONES experiment is currently ongoing to collect data from further crew members. The potential impact of this research is to better understand the effects of microgravity and countermeasures over the time course of an ISS mission cycle. This will enable exercise countermeasures to be tailored Y1 - 2019 SN - 00741795 N1 - International Astronautical Congress: space: the power of the past, the promise of the future - Washington DC, USA/Vereinigte Staaten von Amerika Dauer: 21.10.2019 → 25.10.2019 PB - Pergamon CY - Oxford ER - TY - JOUR A1 - Bruksle, Ieva A1 - Chwallek, Constanze A1 - Krastina, Anzelika T1 - Strengthening sustainability in entrepreneurship education - implications for shifting entrepreneurial thinking towards sustainability at universities JF - ACTA PROSPERITATIS N2 - By developing innovative solutions to social and environmental problems, sustainable ventures carry greatpotential. Entrepreneurship which focuses especially on new venture creation can be developed through education anduniversities, in particular, are called upon to provide an impetus for social change. But social innovations are associatedwith certain hurdles, which are related to the multi-dimensionality, i.e. the tension between creating social,environmental and economic value and dealing with a multiplicity of stakeholders. The already complex field ofentrepreneurship education has to face these challenges. This paper, therefore, aims to identify starting points for theintegration of sustainability into entrepreneurship education. To pursue this goal experiences from three differentproject initiatives between the partner universities: Lapland University of Applied Sciences, FH Aachen University ofApplied Sciences and Turiba University are reflected and findings are systematically condensed into recommendationsfor education on sustainable entrepreneurship. KW - climate change KW - entrepreneurship education KW - Finland KW - Germany KW - Latvia Y1 - 2023 U6 - https://doi.org/10.37804/1691-6077-2023-14-37-48 SN - 1691-6077 VL - 14 IS - 1 SP - 37 EP - 48 PB - Sciendo ER - TY - CHAP A1 - Ketelhut, Maike A1 - Göll, Fabian A1 - Braunstein, Bjoern A1 - Albracht, Kirsten A1 - Abel, Dirk T1 - Iterative learning control of an industrial robot for neuromuscular training T2 - 2019 IEEE Conference on Control Technology and Applications N2 - Effective training requires high muscle forces potentially leading to training-induced injuries. Thus, continuous monitoring and controlling of the loadings applied to the musculoskeletal system along the motion trajectory is required. In this paper, a norm-optimal iterative learning control algorithm for the robot-assisted training is developed. The algorithm aims at minimizing the external knee joint moment, which is commonly used to quantify the loading of the medial compartment. To estimate the external knee joint moment, a musculoskeletal lower extremity model is implemented in OpenSim and coupled with a model of an industrial robot and a force plate mounted at its end-effector. The algorithm is tested in simulation for patients with varus, normal and valgus alignment of the knee. The results show that the algorithm is able to minimize the external knee joint moment in all three cases and converges after less than seven iterations. KW - Knee KW - Training KW - Load modeling KW - Force KW - Iterative learning control Y1 - 2019 SN - 978-1-7281-2767-5 (ePub) SN - 978-1-7281-2766-8 (USB) SN - 978-1-7281-2768-2 (PoD) U6 - https://doi.org/10.1109/CCTA.2019.8920659 N1 - 2019 IEEE Conference on Control Technology and Applications (CCTA) Hong Kong, China, August 19-21, 2019 PB - IEEE CY - New York ER - TY - JOUR A1 - Ketelhut, Maike A1 - Kolditz, Melanie A1 - Göll, Fabian A1 - Braunstein, Bjoern A1 - Albracht, Kirsten A1 - Abel, Dirk T1 - Admittance control of an industrial robot during resistance training JF - IFAC-PapersOnLine N2 - Neuromuscular strength training of the leg extensor muscles plays an important role in the rehabilitation and prevention of age and wealth related diseases. In this paper, we focus on the design and implementation of a Cartesian admittance control scheme for isotonic training, i.e. leg extension and flexion against a predefined weight. For preliminary testing and validation of the designed algorithm an experimental research and development platform consisting of an industrial robot and a force plate mounted at its end-effector has been used. Linear, diagonal and arbitrary two-dimensional motion trajectories with different weights for the leg extension and flexion part are applied. The proposed algorithm is easily adaptable to trajectories consisting of arbitrary six-dimensional poses and allows the implementation of individualized trajectories. KW - Assistive technology KW - Rehabilitation engineering KW - Human-Computer interaction KW - Automatic control Y1 - 2019 U6 - https://doi.org/10.1016/j.ifacol.2019.12.102 SN - 2405-8963 N1 - 14th IFAC Symposium on Analysis, Design, and Evaluation of Human Machine Systems HMS 2019 Tallinn, Estonia, 16–91 September 2019 VL - 52 IS - 19 SP - 223 EP - 228 PB - Elsevier CY - Amsterdam ER - TY - BOOK A1 - Scheilen, Jana A1 - Peiffer, Max A1 - Görlich, Anna-Luisa A1 - Hacke, Theresa ED - Kroll-Ludwigs, Kathrin ED - Bassen-Metz, Yasmine ED - Bernecker, Andreas ED - Eggert, Mathias ED - Fritz, Thomas ED - Golland, Alexander ED - Höhne, Tim ED - Tran, Duc Hung ED - Vogt, Jürgen T1 - Aachener Online-Schriften Wirtschaft und Recht. Band 7. 02/2023 N2 - 1. Die Wirksamkeitsvoraussetzungen der Verdachtskündigung gegenüber einem Arbeitnehmer - Jana Scheilen | Seite 4-66 2. Besteuerungsinkongruenzen im Internationalen Steuerrecht - die Umsetzung der ATAD II in Form des § 4k EStG in Bezug auf hybride Gesellschaften und Betriebsstätten - Max Peiffer | Seite 67-126 3. Der Zuzug einer Gesellschaft aus einem Drittstaat nach Deutschland - Herausforderungen durch die modifizierte Sitztheorie und Lösungsmöglichkeiten - Anna-Luisa Görlich | Seite 127-189 4. Escalation of Commitment und seine Einflussfaktoren in der unternehmerischen Entscheidungsfindung: Ein Szenario-Experiment - Theresa Hacke | Seite 190-245 T3 - Aachener Online-Schriften Wirtschaft und Recht - 7 Y1 - 2023 PB - FH Aachen / Fachbereich Wirtschaftswissenschaften CY - Aachen ER - TY - JOUR A1 - Timme, Michael T1 - Die Erbringung einer Leistung in der irrigen Vorstellung einer Bestellung (Zu BGH, MDR 2023, 1439) JF - Monatsschrift für Deutsches Recht Y1 - 2023 U6 - https://doi.org/10.9785/mdtr-2023-772402 SN - 2194-4202 (online) SN - 0340-1812 (print) VL - 77 IS - 24 SP - R293 EP - R296 PB - Verlag Dr. Otto Schmidt CY - Köln ER - TY - JOUR A1 - Ketelhut, Maike A1 - Brügge, G. M. A1 - Göll, Fabian A1 - Braunstein, Bjoern A1 - Albracht, Kirsten A1 - Abel, Dirk T1 - Adaptive iterative learning control of an industrial robot during neuromuscular training JF - IFAC PapersOnLine N2 - To prevent the reduction of muscle mass and loss of strength coming along with the human aging process, regular training with e.g. a leg press is suitable. However, the risk of training-induced injuries requires the continuous monitoring and controlling of the forces applied to the musculoskeletal system as well as the velocity along the motion trajectory and the range of motion. In this paper, an adaptive norm-optimal iterative learning control algorithm to minimize the knee joint loadings during the leg extension training with an industrial robot is proposed. The response of the algorithm is tested in simulation for patients with varus, normal and valgus alignment of the knee and compared to the results of a higher-order iterative learning control algorithm, a robust iterative learning control and a recently proposed conventional norm-optimal iterative learning control algorithm. Although significant improvements in performance are made compared to the conventional norm-optimal iterative learning control algorithm with a small learning factor, for the developed approach as well as the robust iterative learning control algorithm small steady state errors occur. KW - Iterative learning control KW - Robotic rehabilitation KW - Adaptive control Y1 - 2020 U6 - https://doi.org/10.1016/j.ifacol.2020.12.741 SN - 2405-8963 VL - 53 IS - 2 SP - 16468 EP - 16475 PB - Elsevier CY - Amsterdam ER - TY - JOUR A1 - Hammer, Thorben A1 - Quitter, Julius A1 - Mayntz, Joscha A1 - Bauschat, J.-Michael A1 - Dahmann, Peter A1 - Götten, Falk A1 - Hille, Sebastian A1 - Stumpf, Eike T1 - Free fall drag estimation of small-scale multirotor unmanned aircraft systems using computational fluid dynamics and wind tunnel experiments JF - CEAS Aeronautical Journal N2 - New European Union (EU) regulations for UAS operations require an operational risk analysis, which includes an estimation of the potential danger of the UAS crashing. A key parameter for the potential ground risk is the kinetic impact energy of the UAS. The kinetic energy depends on the impact velocity of the UAS and, therefore, on the aerodynamic drag and the weight during free fall. Hence, estimating the impact energy of a UAS requires an accurate drag estimation of the UAS in that state. The paper at hand presents the aerodynamic drag estimation of small-scale multirotor UAS. Multirotor UAS of various sizes and configurations were analysed with a fully unsteady Reynolds-averaged Navier–Stokes approach. These simulations included different velocities and various fuselage pitch angles of the UAS. The results were compared against force measurements performed in a subsonic wind tunnel and provided good consistency. Furthermore, the influence of the UAS`s fuselage pitch angle as well as the influence of fixed and free spinning propellers on the aerodynamic drag was analysed. Free spinning propellers may increase the drag by up to 110%, depending on the fuselage pitch angle. Increasing the fuselage pitch angle of the UAS lowers the drag by 40% up to 85%, depending on the UAS. The data presented in this paper allow for increased accuracy of ground risk assessments. KW - Multirotor UAS KW - Drag estimation KW - CFD KW - Wind tunnel experiments KW - Wind milling Y1 - 2023 U6 - https://doi.org/10.1007/s13272-023-00702-w SN - 1869-5590 (Online) SN - 1869-5582 (Print) N1 - Corresponding author: Thorben Hammer PB - Springer CY - Wien ER - TY - JOUR A1 - Stäudle, Benjamin A1 - Seynnes, Olivier A1 - Laps, Guido A1 - Göll, Fabian A1 - Brüggemann, Gert-Peter A1 - Albracht, Kirsten T1 - Recovery from achilles tendon repair: a combination of Postsurgery Outcomes and Insufficient remodeling of muscle and tendon JF - Medicine & Science in Sports & Exercise N2 - Achilles tendon rupture (ATR) patients have persistent functional deficits in the triceps surae muscle–tendon unit (MTU). The complex remodeling of the MTU accompanying these deficits remains poorly understood. The purpose of the present study was to associate in vivo and in silico data to investigate the relations between changes inMTU properties and strength deficits inATR patients. Methods: Elevenmale subjects who had undergone surgical repair of complete unilateral ATR were examined 4.6 ± 2.0 (mean ± SD) yr after rupture. Gastrocnemius medialis (GM) tendon stiffness, morphology, and muscle architecture were determined using ultrasonography. The force–length relation of the plantar flexor muscles was assessed at five ankle joint angles. In addition, simulations (OpenSim) of the GM MTU force–length properties were performed with various iterations of MTU properties found between the unaffected and the affected side. Results: The affected side of the patients displayed a longer, larger, and stiffer GM tendon (13% ± 10%, 105% ± 28%, and 54% ± 24%, respectively) compared with the unaffected side. The GM muscle fascicles of the affected side were shorter (32% ± 12%) and with greater pennation angles (31% ± 26%). A mean deficit in plantarflexion moment of 31% ± 10% was measured. Simulations indicate that pairing an intact muscle with a longer tendon shifts the optimal angular range of peak force outside physiological angular ranges, whereas the shorter muscle fascicles and tendon stiffening seen in the affected side decrease this shift, albeit incompletely. Conclusions: These results suggest that the substantial changes in MTU properties found in ATR patients may partly result from compensatory remodeling, although this process appears insufficient to fully restore muscle function. KW - Tendon Rupture KW - Stiffness KW - Simulation KW - Muscle Force KW - Muscle Fascicle Y1 - 2021 U6 - https://doi.org/10.1249/MSS.0000000000002592 SN - 1530-0315 VL - 53 IS - 7 SP - 1356 EP - 1366 PB - American College of Sports Medicine CY - Philadelphia, Pa. ER - TY - JOUR A1 - Monti, Elena A1 - Waldvogel, Janice A1 - Ritzmann, Ramona A1 - Freyler, Kathrin A1 - Albracht, Kirsten A1 - Helm, Michael A1 - De Cesare, Niccolò A1 - Pavan, Piero A1 - Reggiani, Carlo A1 - Gollhofer, Albert A1 - Narici, Marco Vincenzo T1 - Muscle in variable gravity: “I do not know where I am, but I know what to do” JF - Frontiers in Physiology N2 - Performing tasks, such as running and jumping, requires activation of the agonist and antagonist muscles before (motor unit pre-activation) and during movement performance (Santello and Mcdonagh, 1998). A well-timed and regulated muscle activation elicits a stretch-shortening cycle (SSC) response, naturally occurring in bouncing movements (Ishikawa and Komi, 2004; Taube et al., 2012). By definition, the SSC describes the stretching of a pre-activated muscle-tendon complex immediately followed by a muscle shortening in the concentric push-off phase (Komi, 1984). Given the importance of SSC actions for human movement, it is not surprising that many studies investigated the biomechanics of this phenomenon; in particular, drop jumps (DJs) represent a good paradigm to study muscle fascicle and tendon behavior in ballistic movements involving the SSC. Within a DJ, three main phases [pre-activation, braking, and push-off (PO; Komi, 2000)] have been recognized and extensively studied in common and challenging conditions, such as changes in load, falling height, or simulated hypo-gravity (Avela et al., 1994; Arampatzis et al., 2001; Fukashiro et al., 2005; Ishikawa et al., 2005; Sousa et al., 2007; Ritzmann et al., 2016; Helm et al., 2020). These studies show that the timing and amount of triceps-surae muscle-tendon unit pre-activation in DJs are differentially regulated based on the load applied to the muscle, being optimal in normal “Earth” gravity conditions (Avela et al., 1994), but decreased in simulated hypo-gravity, hyper-gravity (Avela et al., 1994; Ritzmann et al., 2016), or unknown conditions (i.e., unknown falling heights; Helm et al., 2020). Some authors indicated that, when falling from heights different from the optimal one [defined as the drop height giving a maximum DJ performance indicated as peak ground reaction force (GRF) or jump high], electromyographic (EMG) activity of the plantar flexors increases from lower than optimal to higher than optimal heights (Ishikawa and Komi, 2004; Sousa et al., 2007). These findings highlight the ability of the central nervous system to regulate the timing and amount of pre-activation according to different jumping conditions, thus regulating muscle fascicle length, tendon and joint stiffness as well as position, in order to safely land on the ground and quickly re-bounce. Similarly, to pre-activation, also in the braking phase, the plantar flexors are differentially regulated. In optimal height (i.e., load) jumping conditions, gastrocnemius medialis (GM) fascicles shorten at early ground contact (possibly due to the intervention of the stretch reflex; Gollhofer et al., 1992) and behave quasi-isometrically in the late braking phase, enabling tendon elongation, and storage of elastic energy (Gollhofer et al., 1992; Fukashiro et al., 2005; Sousa et al., 2007). When increasing the falling height (augmenting the impact GRF), the quasi-isometric behavior of fascicles disappears, and fast fascicle lengthening occurs (Ishikawa et al., 2005; Sousa et al., 2007). In the third and last PO phase, fascicles shorten and the tendon releases the elastic energy previously stored. Bobbert et al. (1987) reported no influence of jumping height on the work done and on the net vertical impulse assessed during PO; this observation suggests that, despite an optimal DJ performance might be achieved only in specific conditions (falling heights, loads), the central nervous system seems to be able to regulate muscle behavior in order to effectively perform the required task also in challenging situations. Although the regulation of triceps-surae muscle-tendon unit in DJs has been extensively investigated, very few studies focused on sarcomeres behavior during the performance of this SSC movement (Kurokawa et al., 2003; Fukashiro et al., 2005, 2006). Sarcomeres represent muscle contractile units and are known to express different amounts of force depending on their length (Gordon et al., 1966; Walker and Schrodt, 1974); thus, understanding the time course of their responses during DJs is fundamental to gain further insights into muscle force-generating capacity. In vivo measurement of sarcomere length in humans has been so far been performed only in static positions and under highly controlled experimental conditions (Llewellyn et al., 2008; Sanchez et al., 2015). Instead, human sarcomere length estimation (achieved by dividing GM measured fascicle length for a fixed sarcomere number) in dynamic contractions provided an indirect measure of sarcomere operating range during squat jump, countermovement jump, and DJ (Fukashiro et al., 2005, 2006; Kurokawa et al., 2003). The results of these studies showed that sarcomeres operate in the ascending limb of their length-tension (L-T) relationship in all types of jumps, and particularly so in DJ. However, most of the available observations on sarcomere and muscle fascicle behavior were made in condition of constant gravity. Thus, in order to understand how sarcomere and muscle fascicle length are regulated in variable gravity conditions, we performed experiments in a parabolic flight, involving variable gravity levels, ranging from about zero-g to about double the Earth’s gravity (1 g; Waldvogel et al., 2021). Specifically, the aims of the present study were as follows: 1. To investigate the ability of the neuromuscular system in regulating fascicle length in response to conditions of variable gravity. 2. To estimate sarcomere operative length in the different DJ phases, in order to calculate its theoretical force production and its possible modulation in conditions of variable gravity. We hypothesized that muscle fascicles would be differentially regulated in different gravity conditions compared to 1 g, particularly in anticipation of landing and re-bouncing in unknown gravity levels. In addition, we hypothesized that sarcomeres would operate in the upper part of the ascending limb of their L-T relationship, possibly lengthening during the braking phase (especially in hyper-gravity) while operating quasi-isometrically in 1 g. KW - parabolic flight KW - drop jump KW - hypo-gravity KW - hyper-gravity KW - sarcomere operating length Y1 - 2021 U6 - https://doi.org/10.3389/fphys.2021.714655 SN - 1664-042X VL - 12 PB - Frontiers Research Foundation CY - Lausanne ER - TY - JOUR A1 - Werkhausen, Amelie A1 - Willwacher, Steffen A1 - Albracht, Kirsten T1 - Medial gastrocnemius muscle fascicles shorten throughout stance during sprint acceleration JF - Scandinavian Journal of Medicine & Science in Sports N2 - The compliant nature of distal limb muscle-tendon units is traditionally considered suboptimal in explosive movements when positive joint work is required. However, during accelerative running, ankle joint net mechanical work is positive. Therefore, this study aims to investigate how plantar flexor muscle-tendon behavior is modulated during fast accelerations. Eleven female sprinters performed maximum sprint accelerations from starting blocks, while gastrocnemius muscle fascicle lengths were estimated using ultrasonography. We combined motion analysis and ground reaction force measurements to assess lower limb joint kinematics and kinetics, and to estimate gastrocnemius muscle-tendon unit length during the first two acceleration steps. Outcome variables were resampled to the stance phase and averaged across three to five trials. Relevant scalars were extracted and analyzed using one-sample and two-sample t-tests, and vector trajectories were compared using statistical parametric mapping. We found that an uncoupling of muscle fascicle behavior from muscle-tendon unit behavior is effectively used to produce net positive mechanical work at the joint during maximum sprint acceleration. Muscle fascicles shortened throughout the first and second steps, while shortening occurred earlier during the first step, where negative joint work was lower compared with the second step. Elastic strain energy may be stored during dorsiflexion after touchdown since fascicles did not lengthen at the same time to dissipate energy. Thus, net positive work generation is accommodated by the reuse of elastic strain energy along with positive gastrocnemius fascicle work. Our results show a mechanism of how muscles with high in-series compliance can contribute to net positive joint work. KW - locomotion KW - muscle mechanics KW - running KW - sprint start KW - ultrasonography Y1 - 2021 U6 - https://doi.org/10.1111/sms.13956 SN - 0905-7188 (Druckausgabe) SN - 1600-0838 (Onlineausgabe) VL - 31 IS - 7 SP - 1471 EP - 1480 PB - Wiley-Blackwell CY - Oxford ER - TY - JOUR A1 - Richter, Charlotte A1 - Braunstein, Björn A1 - Stäudle, Benjamin A1 - Attias, Julia A1 - Süss, Alexander A1 - Weber, Tobias A1 - Mileva, Katya N. A1 - Rittweger, Jörn A1 - Green, David A. A1 - Albracht, Kirsten T1 - Gastrocnemius medialis contractile behavior during running differs between simulated Lunar and Martian gravities JF - Scientific reports N2 - The international partnership of space agencies has agreed to proceed forward to the Moon sustainably. Activities on the Lunar surface (0.16 g) will allow crewmembers to advance the exploration skills needed when expanding human presence to Mars (0.38 g). Whilst data from actual hypogravity activities are limited to the Apollo missions, simulation studies have indicated that ground reaction forces, mechanical work, muscle activation, and joint angles decrease with declining gravity level. However, these alterations in locomotion biomechanics do not necessarily scale to the gravity level, the reduction in gastrocnemius medialis activation even appears to level off around 0.2 g, while muscle activation pattern remains similar. Thus, it is difficult to predict whether gastrocnemius medialis contractile behavior during running on Moon will basically be the same as on Mars. Therefore, this study investigated lower limb joint kinematics and gastrocnemius medialis behavior during running at 1 g, simulated Martian gravity, and simulated Lunar gravity on the vertical treadmill facility. The results indicate that hypogravity-induced alterations in joint kinematics and contractile behavior still persist between simulated running on the Moon and Mars. This contrasts with the concept of a ceiling effect and should be carefully considered when evaluating exercise prescriptions and the transferability of locomotion practiced in Lunar gravity to Martian gravity. KW - Bone quality and biomechanics KW - Environmental impact KW - Skeletal muscle KW - Tendons KW - Ultrasound Y1 - 2021 U6 - https://doi.org/10.1038/s41598-021-00527-9 SN - 2045-2322 N1 - Corresponding author: Charlotte Richter VL - 11 IS - Article number: 22555 PB - Springer Nature CY - London ER - TY - JOUR A1 - Quittmann, Oliver J. A1 - Abel, Thomas A1 - Albracht, Kirsten A1 - Strüder, Heiko K. T1 - Biomechanics of all-out handcycling exercise: kinetics, kinematics and muscular activity of a 15-s sprint test in able-bodied participants JF - Sports Biomechanics N2 - This study aims to quantify the kinematics, kinetics and muscular activity of all-out handcycling exercise and examine their alterations during the course of a 15-s sprint test. Twelve able-bodied competitive triathletes performed a 15-s all-out sprint test in a recumbent racing handcycle that was attached to an ergometer. During the sprint test, tangential crank kinetics, 3D joint kinematics and muscular activity of 10 muscles of the upper extremity and trunk were examined using a power metre, motion capturing and surface electromyography (sEMG), respectively. Parameters were compared between revolution one (R1), revolution two (R2), the average of revolution 3 to 13 (R3) and the average of the remaining revolutions (R4). Shoulder abduction and internal-rotation increased, whereas maximal shoulder retroversion decreased during the sprint. Except for the wrist angles, angular velocity increased for every joint of the upper extremity. Several muscles demonstrated an increase in muscular activation, an earlier onset of muscular activation in crank cycle and an increased range of activation. During the course of a 15-s all-out sprint test in handcycling, the shoulder muscles and the muscles associated to the push phase demonstrate indications for short-duration fatigue. These findings are helpful to prevent injuries and improve performance in all-out handcycling. KW - Handbike KW - sEMG KW - Paralympic sport KW - performance testing KW - high-intensity exercise Y1 - 2022 U6 - https://doi.org/10.1080/14763141.2020.1745266 SN - 1752-6116 (Onlineausgabe) SN - 1476-3141 (Druckausgabe) VL - 21 IS - 10 SP - 1200 EP - 1223 PB - Taylor & Francis CY - London ER - TY - JOUR A1 - Richter, Charlotte A1 - Braunstein, Bjoern A1 - Stäudle, Benjamin A1 - Attias, Julia A1 - Suess, Alexander A1 - Weber, Tobias A1 - Mileva, Katja N. A1 - Rittweger, Joern A1 - Green, David A. A1 - Albracht, Kirsten T1 - Gastrocnemius medialis contractile behavior is preserved during 30% body weight supported gait training JF - Frontiers in Sports and Active Living N2 - Rehabilitative body weight supported gait training aims at restoring walking function as a key element in activities of daily living. Studies demonstrated reductions in muscle and joint forces, while kinematic gait patterns appear to be preserved with up to 30% weight support. However, the influence of body weight support on muscle architecture, with respect to fascicle and series elastic element behavior is unknown, despite this having potential clinical implications for gait retraining. Eight males (31.9 ± 4.7 years) walked at 75% of the speed at which they typically transition to running, with 0% and 30% body weight support on a lower-body positive pressure treadmill. Gastrocnemius medialis fascicle lengths and pennation angles were measured via ultrasonography. Additionally, joint kinematics were analyzed to determine gastrocnemius medialis muscle–tendon unit lengths, consisting of the muscle's contractile and series elastic elements. Series elastic element length was assessed using a muscle–tendon unit model. Depending on whether data were normally distributed, a paired t-test or Wilcoxon signed rank test was performed to determine if body weight supported walking had any effects on joint kinematics and fascicle–series elastic element behavior. Walking with 30% body weight support had no statistically significant effect on joint kinematics and peak series elastic element length. Furthermore, at the time when peak series elastic element length was achieved, and on average across the entire stance phase, muscle–tendon unit length, fascicle length, pennation angle, and fascicle velocity were unchanged with respect to body weight support. In accordance with unchanged gait kinematics, preservation of fascicle–series elastic element behavior was observed during walking with 30% body weight support, which suggests transferability of gait patterns to subsequent unsupported walking. KW - AlterG KW - rehabilitation KW - gait KW - walking KW - ultrasound imaging KW - series elastic element behavior KW - muscle fascicle behavior KW - unloading Y1 - 2021 U6 - https://doi.org/10.3389/fspor.2020.614559 SN - 2624-9367 VL - 2021 IS - 2 PB - Frontiers CY - Lausanne ER - TY - JOUR A1 - Stäudle, Benjamin A1 - Seynnes, Olivier A1 - Laps, Guido A1 - Brüggemann, Gert-Peter A1 - Albracht, Kirsten T1 - Altered gastrocnemius contractile behavior in former achilles tendon rupture patients during walking JF - Frontiers in Physiology N2 - Achilles tendon rupture (ATR) remains associated with functional limitations years after injury. Architectural remodeling of the gastrocnemius medialis (GM) muscle is typically observed in the affected leg and may compensate force deficits caused by a longer tendon. Yet patients seem to retain functional limitations during—low-force—walking gait. To explore the potential limits imposed by the remodeled GM muscle-tendon unit (MTU) on walking gait, we examined the contractile behavior of muscle fascicles during the stance phase. In a cross-sectional design, we studied nine former patients (males; age: 45 ± 9 years; height: 180 ± 7 cm; weight: 83 ± 6 kg) with a history of complete unilateral ATR, approximately 4 years post-surgery. Using ultrasonography, GM tendon morphology, muscle architecture at rest, and fascicular behavior were assessed during walking at 1.5 m⋅s–1 on a treadmill. Walking patterns were recorded with a motion capture system. The unaffected leg served as control. Lower limbs kinematics were largely similar between legs during walking. Typical features of ATR-related MTU remodeling were observed during the stance sub-phases corresponding to series elastic element (SEE) lengthening (energy storage) and SEE shortening (energy release), with shorter GM fascicles (36 and 36%, respectively) and greater pennation angles (8° and 12°, respectively). However, relative to the optimal fascicle length for force production, fascicles operated at comparable length in both legs. Similarly, when expressed relative to optimal fascicle length, fascicle contraction velocity was not different between sides, except at the time-point of peak series elastic element (SEE) length, where it was 39 ± 49% lower in the affected leg. Concomitantly, fascicles rotation during contraction was greater in the affected leg during the whole stance-phase, and architectural gear ratios (AGR) was larger during SEE lengthening. Under the present testing conditions, former ATR patients had recovered a relatively symmetrical walking gait pattern. Differences in seen AGR seem to accommodate the profound changes in MTU architecture, limiting the required fascicle shortening velocity. Overall, the contractile behavior of the GM fascicles does not restrict length- or velocity-dependent force potentials during this locomotor task. KW - tendon rupture KW - muscle fascicle behavior KW - walking gait KW - force generation KW - ultrasound imaging Y1 - 2022 U6 - https://doi.org/10.3389/fphys.2022.792576 SN - 1664-042X VL - 13 PB - Frontiers Research Foundation CY - Lausanne ER - TY - GEN T1 - Ordnung zur Änderung der Prüfungsordnung für die Bachelorstudiengänge „Schienenfahrzeugtechnik“ „Schienenfahrzeugtechnik (Teilzeit)“ und „Dualer Studiengang Schienenfahrzeugtechnik (DIRail)“ im Fachbereich Maschinenbau und Mechatronik an der Fachhochschule Aachen T3 - FH-Mitteilungen - 70/2019 KW - Amtliche Mitteilung KW - Bachelor KW - Prüfungsordnung KW - Änderungsordnung KW - Maschinenbau und Mechatronik Y1 - 2019 ER - TY - GEN T1 - Prüfungsordnung für die Bachelorstudiengänge „Schienenfahrzeugtechnik“ „Schienenfahrzeugtechnik (Teilzeit)“ und „Dualer Studiengang Schienenfahrzeugtechnik (DIRail)“ im Fachbereich Maschinenbau und Mechatronik an der Fachhochschule Aachen T3 - FH-Mitteilungen - 71/2019 KW - Prüfungsordnung KW - Bachelor KW - Maschinenbau und Mechatronik KW - lesbare Fassung Y1 - 2019 ER - TY - GEN T1 - Ordnung zur Änderung der Ordnung zur Aufhebung der Studien- und Prüfungsordnung für den Masterstudiengang „Bauingenieurwesen“ vom 10. Dezember 2012 (FH-Mitteilung Nr. 129/2012) in der Fassung der Bekanntmachung der Änderungsordnungen vom 30. Mai 2017 (FH-Mitteilung Nr. 58/2017) an der Fachhochschule Aachen T3 - FH-Mitteilungen - 81/2019 KW - Amtliche Mitteilung KW - Änderungsordnung KW - Studien- und Prüfungsordnung KW - Master KW - Bauingenieurwesen Y1 - 2019 ER - TY - GEN T1 - Ordnung zur Änderung der Ordnung zur Aufhebung der Studien- und Prüfungsordnung für den Masterstudiengang „Facility Management“ vom 29. November 2012 (FH-Mitteilung Nr. 127/2012) in der Fassung der Bekanntmachung der Änderungsordnungen vom 3. Februar 2016 (FH-Mitteilung Nr. 10/2016) an der Fachhochschule Aachen T3 - FH-Mitteilungen - 83/2019 KW - Amtliche Mitteilung KW - Änderungsordnung KW - Studien- und Prüfungsordnung KW - Master KW - Facility Management Y1 - 2019 ER - TY - GEN T1 - Studien- und Prüfungsordnung für den Bachelorstudiengang Bauingenieurwesen (7-semestrig), Bachelorstudiengang Bauingenieurwesen mit Praxissemester (8-semestrig) und Bachelorstudiengang Bauingenieurwesen mit Auslandssemester (8-semestrig) Abschluss Bachelor of Engineering T3 - FH-Mitteilungen - 84/2019 KW - Amtliche Mitteilung KW - Lesbare Fassung KW - Studien- und Prüfungsordnung KW - Bachelor KW - Bauingenieurwesen Y1 - 2019 ER - TY - GEN T1 - Studien- und Prüfungsordnung für den Bachelorstudiengang Bauingenieurwesen (7-semestrig), Bachelorstudiengang Bauingenieurwesen mit Praxissemester (8-semestrig), Bachelorstudiengang Bauingenieurwesen mit Auslandssemester (8-semestrig) Abschluss Bachelor of Engineering : vom 1. September 2011 – FH-Mitteilung Nr. 76/2011 in der Fassung der Bekanntmachung der Änderungsordnung vom 16. August 2019 – FH-Mitteilung Nr. 74/2019 (Nichtamtliche lesbare Fassung, Studienbeginn WS 2016/17–2017/18) T3 - FH-Mitteilungen - 85/2019 KW - Amtliche Mitteilung KW - Studien- und Prüfungsordnung KW - Lesbare Fassung KW - Bachelor KW - Bauingenieurwesen Y1 - 2019 ER - TY - GEN T1 - Ordnung zur Aufhebung der Studien- und Prüfungsordnung für die Bachelorstudiengänge „Bauingenieurwesen“ (7-semestrig), „Bauingenieurwesen mit Praxissemester“ (8-semestrig) und „Bauingenieurwesen mit Auslandssemester“ (8-semestrig) vom 1. September 2011 (FH-Mitteilung Nr. 76/2011) in der Fassung der Bekanntmachung der Änderungsordnungen vom 22. August 2013 (FH-Mitteilung Nr. 88/2013), 8. Juni 2016 (FH-Mitteilung Nr. 80/2016) und 16. August 2019 (FH-Mitteilung Nr. 74/2019) an der Fachhochschule Aachen : vom 24. Juli 2018 – FH-Mitteilung Nr. 119/2018 in der Fassung der Bekanntmachung der Änderungsordnung vom 16. August 2019 – FH-Mitteilung Nr. 75/2019 (Nichtamtliche lesbare Fassung) T3 - FH-Mitteilungen - 86/2019 KW - Amtliche Mitteilung KW - Lesbare Fassung KW - Studien- und Prüfungsordnung KW - Bachelor KW - Bauingenieurwesen Y1 - 2019 ER - TY - GEN T1 - Studien- und Prüfungsordnung des Studiengangs Holzingenieurwesen (7-semestrig) – Abschluss Bachelor of Engineering – im Fachbereich Bauingenieurwesen an der Fachhochschule Aachen : vom 16. Juli 2012 – FH-Mitteilung Nr. 66/2012 in der Fassung der Bekanntmachung der Änderungsordnung vom 16. August 2019 – FH-Mitteilung Nr. 76/2019 (Nichtamtliche lesbare Fassung) T3 - FH-Mitteilungen - 87/2019 KW - Amtliche Mitteilung KW - Lesbare Fassung KW - Studien- und Prüfungsordnung KW - Bachelor KW - Holzingenieurwesen Y1 - 2019 ER - TY - GEN T1 - Ordnung zur Aufhebung der Studien- und Prüfungsordnung für den Bachelorstudiengang „Holzingenieurwesen“ (7-semestrig) vom 16. Juli 2012 (FH-Mitteilung Nr. 66/2012) in der Fassung der Bekanntmachung der Änderungsordnungen vom 6. Juli 2016 (FH-Mitteilung Nr. 95/2016) und 16. August 2019 (FH-Mitteilung Nr. 76/2019) an der Fachhochschule Aachen : vom 24. Juli 2018 – FH-Mitteilung Nr. 120/2018 in der Fassung der Bekanntmachung der Änderungsordnung vom 16. August 2019 – FH-Mitteilung Nr. 77/2019 (Nichtamtliche lesbare Fassung) T3 - FH-Mitteilungen - 88/2019 KW - Amtliche Mitteilung KW - Lesbare Fassung KW - Studien- und Prüfungsordnung KW - Bachelor KW - Holzingenieurwesen Y1 - 2019 ER - TY - GEN T1 - Prüfungsordnung für den dreisemestrigen Masterstudiengang „Industrial Engineering“ an der Fachhochschule Aachen : vom 11. Dezember 2014 – FH-Mitteilung Nr. 154/2014 in der Fassung der Bekanntmachung der Änderungsordnung vom 5. Februar 2019 – FH-Mitteilung Nr. 5/2019 (Nichtamtliche lesbare Fassung | Studienbeginn ab SS 2016) T3 - FH-Mitteilungen - 104/2019 KW - Amtliche Mitteilung KW - Lesbare Fassung KW - Prüfungsordnung KW - Master KW - Industrial Engineering Y1 - 2019 ER - TY - GEN T1 - Prüfungsordnung für den dreisemestrigen Masterstudiengang „Industrial Engineering“ an der Fachhochschule Aachen : vom 11. Dezember 2014 – FH-Mitteilung Nr. 154/2014 in der Fassung der Bekanntmachung der Änderungsordnung vom 5. Februar 2019 – FH-Mitteilung Nr. 5/2019 (Nichtamtliche lesbare Fassung | Studienbeginn ab WS 2017/18) T3 - FH-Mitteilungen - 105/2019 KW - Amtliche Mitteilung KW - Lesbare Fassung KW - Prüfungsordnung KW - Master KW - Industrial Engineering Y1 - 2019 ER - TY - GEN T1 - Prüfungsordnung für den viersemestrigen Masterstudiengang „Industrial Engineering“ an der Fachhochschule Aachen : vom 11.Dezember 2014 – FH-Mitteilung Nr. 156/2014 in der Fassung der Bekanntmachung der Änderungsordnung vom 5. Februar 2019 – FH-Mitteilung Nr. 6/2019 (Nichtamtliche lesbare Fassung | Studienbeginn ab WS 2015/16) T3 - FH-Mitteilungen - 106/2019 KW - Amtliche Mitteilung KW - Lesbare Fassung KW - Prüfungsordnung KW - Master KW - Industrial Engineering Y1 - 2019 ER - TY - GEN T1 - Prüfungsordnung für den viersemestrigen Masterstudiengang „Industrial Engineering“ an der Fachhochschule Aachen : vom 11.Dezember 2014 – FH-Mitteilung Nr. 156/2014 in der Fassung der Bekanntmachung der Änderungsordnung vom 5. Februar 2019 – FH-Mitteilung Nr. 6/2019 (Nichtamtliche lesbare Fassung | Studienbeginn ab WS 2017/18) T3 - FH-Mitteilungen - 107/2019 KW - Amtliche Mitteilung KW - Lesbare Fassung KW - Prüfungsordnung KW - Master KW - Industrial Engineering Y1 - 2019 ER - TY - GEN T1 - Prüfungsordnung für den viersemestrigen Masterstudiengang „Industrial Engineering“ Fachbereich Wirtschaftswissenschaften Fachbereich Maschinenbau und Mechatronik an der Fachhochschule Aachen : vom 11. Dezember 2014 – FH-Mitteilung Nr. 156/2014 in der Fassung der Bekanntmachung der Änderungsordnung vom 5. Februar 2019 – FH-Mitteilung Nr. 6/2019 (Nichtamtliche lesbare Fassung | Studienbeginn ab WS 2018/19) T3 - FH-Mitteilungen - 108/2019 KW - Amtliche Mitteilung KW - Lesbare Fassung KW - Prüfungsordnung KW - Master KW - Industrial Engineering Y1 - 2019 ER - TY - GEN T1 - 4. Ordnung zur Änderung der Zugangsordnung für den Masterstudiengang Elektrotechnik im Fachbereich Elektrotechnik und Informationstechnik an der Fachhochschule Aachen : vom 5. November 2019 T3 - FH-Mitteilungen - 109/2019 KW - Amtliche Mitteilung KW - Änderungsordnung KW - Zugangsordnung KW - Master KW - Elektrotechnik Y1 - 2019 ER - TY - GEN T1 - Zugangsordnung für die Masterstudiengänge „Elektrotechnik“ und „Elektrotechnik (Teilzeit)“ im Fachbereich Elektrotechnik und Informationstechnik an der Fachhochschule Aachen : vom 22. Januar 2010 – FH-Mitteilung Nr. 6/2010 in der Fassung der Bekanntmachung der Änderungsordnung vom 5. November 2019 – FH-Mitteilung Nr. 109/2019 (Nichtamtliche lesbare Fassung) T3 - FH-Mitteilungen - 110/2019 KW - Amtliche Mitteilung KW - Lesbare Fassung KW - Zugangsordnung KW - Master KW - Elektrotechnik Y1 - 2019 ER - TY - GEN T1 - Prüfungsordnung für die Masterstudiengänge „Elektrotechnik“ und „Elektrotechnik (Teilzeit)“ im Fachbereich Elektrotechnik und Informationstechnik an der Fachhochschule Aachen : vom 5. November 2019 T3 - FH-Mitteilungen - 111/2019 KW - Amtliche Mitteilung KW - Prüfungsordnung KW - Master KW - Elektrotechnik KW - Elektrotechnik (Teilzeit) Y1 - 2019 ER - TY - GEN T1 - 4. Ordnung zur Änderung der Zugangsordnung für den Masterstudiengang Information Systems Engineering im Fachbereich Elektrotechnik und Informationstechnik an der Fachhochschule Aachen : vom 5. November 2019 T3 - FH-Mitteilungen - 112/2019 KW - Amtliche Mitteilung KW - Änderungsordnung KW - Zugangsordnung KW - Master KW - Information Systems Engineering Y1 - 2019 ER - TY - GEN T1 - Zugangsordnung für die Masterstudiengänge „Information Systems Engineering“ und „Information Systems Engineering (Teilzeit)“ im Fachbereich Elektrotechnik und Informationstechnik an der Fachhochschule Aachen : vom 22. Januar 2010 – FH-Mitteilung Nr. 4/2010 in der Fassung der Bekanntmachung der Änderungsordnung vom 5. November 2019 – FH-Mitteilung Nr. 112/2019 (Nichtamtliche lesbare Fassung) T3 - FH-Mitteilungen - 113/2019 KW - Amtliche Mitteilung KW - Lesbare Fassung KW - Zugangsordnung KW - Master KW - Information Systems Engineering Y1 - 2019 ER - TY - RPRT A1 - Albracht, Kirsten A1 - Ritzmann, Ramona A1 - Kramer, Andreas A1 - Meskemper, Joshua A1 - Stäudle, Benjamin A1 - Kümmel, Jacob A1 - Freyler, Katrin A1 - Felsenberg, Dieter A1 - Gruber, Marksu A1 - Gollhofer, Albert A1 - Belavy, Daniel T1 - Vorhaben: Muskelkraftgenerierungsfähigkeit in Mikrogravitation KW - Elektromyographie KW - Bein KW - Extensor KW - Elektrostimulation KW - Raumfahrt Y1 - 2017 U6 - https://doi.org/10.2314/KXP:1670327353 N1 - Förderkennzeichen: BMWi 50WB1428 Öffentlicher Schlussbericht für die Technische Informationsbibliothek der Universität Hannover Berichtszeitraum: 01.09.2014 - 31.01.2017 PB - Deutsche Sporthochschule Köln CY - Klön ER - TY - GEN T1 - Prüfungsordnung für die Masterstudiengänge „Information Systems Engineering“ und „Information Systems Engineering (Teilzeit)“ an der Fachhochschule Aachen : vom 5. November 2019 T3 - FH-Mitteilungen - 114/2019 KW - Amtliche Mitteilung KW - Prüfungsordnung KW - Master KW - Information Systems Engineering KW - Information Systems Engineering (Teilzeit) Y1 - 2019 ER - TY - GEN T1 - 2. Ordnung zur Änderung der Beitragsordnung der Studierendenschaft der Fachhochschule Aachen : vom 7. November 2019 T3 - FH-Mitteilungen - 115/2019 KW - Amtliche Mitteilung KW - Änderungsordnung KW - Beitragsordnung der Studierendenschaft Y1 - 2019 ER - TY - GEN T1 - Beitragsordnung der Studierendenschaft der Fachhochschule Aachen : vom 11. Dezember 2018 – FH-Mitteilung Nr. 168/2018 in der Fassung der Bekanntmachung der Änderungsordnung vom 7. November 2019 – FH-Mitteilung Nr. 115/2019 (Nichtamtliche lesbare Fassung) T3 - FH-Mitteilungen - 116/2019 KW - Amtliche Mitteilung KW - Lesbare Fassung KW - Beitragsordnung der Studierendenschaft Y1 - 2019 ER - TY - GEN T1 - Gesamtprüfungsordnung für den Bachelorstudiengang „Bauingenieurwesen mit Orientierungssemester“ an der Fachhochschule Aachen und der RWTH Aachen : vom 8. November 2019 T3 - FH-Mitteilungen - 117/2019 KW - Amtliche Mitteilung KW - Gesamtprüfungsordnung KW - Bachelor KW - Bauingenieurwesen mit Orientierungssemester KW - RWTH Aachen Y1 - 2019 ER - TY - GEN T1 - Ordnung zur Änderung der Prüfungsordnung für die Bachelorstudiengänge Bauingenieurwesen, Bauingenieurwesen mit Praxissemester, Bauingenieurwesen mit Auslandssemester, Bauingenieurwesen Double Degree (NUST) und Bauingenieurwesen Dual an der Fachhochschule Aachen : vom 8. November 2019 T3 - FH-Mitteilungen - 118/2019 KW - Amtliche Mitteilung KW - Änderungsordnung KW - Prüfungsordnung KW - Bachelor KW - Bauingenieurwesen Y1 - 2019 ER - TY - GEN T1 - Prüfungsordnung für die Bachelorstudiengänge Bauingenieurwesen, Bauingenieurwesen mit Praxissemester, Bauingenieurwesen mit Auslandssemester, Bauingenieurwesen Double Degree (NUST), Bauingenieurwesen Dual und Bauingenieurwesen mit Orientierungssemester im Fachbereich Bauingenieurwesen an der Fachhochschule Aachen : vom 28. Juni 2018 – FH-Mitteilung Nr. 89/2018 in der Fassung der Bekanntmachung der Änderungsordnung vom 8. November 2019 – FH-Mitteilung Nr. 118/2019 (Nichtamtliche lesbare Fassung) T3 - FH-Mitteilungen - 119/2019 KW - Amtliche Mitteilung KW - Lesbare Fassung KW - Prüfungsordnung KW - Bachelor KW - Bauingenieurwesen Y1 - 2019 ER - TY - GEN T1 - Ordnung zur Änderung der Prüfungsordnung für den Bachelorstudiengang Holzingenieurwesen im Fachbereich Bauingenieurwesen an der Fachhochschule Aachen : vom 8. November 2019 T3 - FH-Mitteilungen - 120/2019 KW - Amtliche Mitteilung KW - Änderungsordnung KW - Prüfungsordnung KW - Bachelor KW - Holzingenieurwesen Y1 - 2019 ER - TY - GEN T1 - Prüfungsordnung für die Bachelorstudiengänge Holzingenieurwesen, Holzingenieurwesen mit Praxissemester, Holzingenieurwesen mit Auslandssemester, Holzingenieurwesen Dual und Holzingenieurwesen mit Orientierungssemester : vom 28. Juni 2018 – FH-Mitteilung Nr. 90/2018 in der Fassung der Bekanntmachung der Änderungsordnung vom 8. November 2019 – FH-Mitteilung Nr. 120/2019 (Nichtamtliche lesbare Fassung) T3 - FH-Mitteilungen - 121/2019 KW - Amtliche Mitteilung KW - Lesbare Fassung KW - Prüfungsordnung KW - Bachelor KW - Holzingenieurwesen Y1 - 2019 ER - TY - GEN T1 - Zugangsordnung für die Masterstudiengänge „Energiewirtschaft & Informatik“ (3 Semester) und „Energiewirtschaft & Informatik“ (4 Semester) Fachbereich Energietechnik Fachbereich Medizintechnik und Technomathematik an der Fachhochschule Aachen : vom 8. November 2019 T3 - FH-Mitteilungen - 122/2019 KW - Amtliche Mitteilung KW - Zugangsordnung KW - Master KW - Energiewirtschaft KW - Informatik Y1 - 2019 ER - TY - GEN T1 - Prüfungsordnung für die Masterstudiengänge „Energiewirtschaft & Informatik“ (3 Semester) und „Energiewirtschaft & Informatik“ (4 Semester) Fachbereich Energietechnik Fachbereich Medizintechnik und Technomathematik an der Fachhochschule Aachen : vom 8. November 2019 T3 - FH-Mitteilungen - 123/2019 KW - Amtliche Mitteilung KW - Prüfungsordnung KW - Master KW - Energiewirtschaft KW - Informatik Y1 - 2019 ER - TY - GEN T1 - Richtlinie zur Durchführung von Sonderveranstaltungen in den Gebäuden und Liegenschaften der FH Aachen (Veranstaltungsrichtlinie) : vom 20. November 2019 T3 - FH-Mitteilungen - 124a/2019 KW - Amtliche Mitteilung KW - Richtlinie KW - Veranstaltungsrichtlinie KW - Durchführung von Sonderveranstaltungen Y1 - 2019 ER - TY - GEN T1 - Richtlinie zur Durchführung von Sonderveranstaltungen in den Gebäuden und Liegenschaften der FH Aachen (Veranstaltungsrichtlinie) : vom 20. November 2019 Anlage 1 aktualisiert am 22. Januar 2020 T3 - FH-Mitteilungen - 124b/2019 KW - Amtliche Mitteilung KW - Richtlinie KW - Veranstaltungsrichtlinie KW - Durchführung von Sonderveranstaltungen KW - Aktualisierung Y1 - 2019 ER - TY - GEN T1 - Richtlinie für die Beschäftigung und Vergütung studentischer und wissenschaftlicher Hilfskräfte an der Fachhochschule Aachen : vom 20. November 2019 T3 - FH-Mitteilungen - 125a/2019 KW - Amtliche Mitteilung KW - Richtlinie KW - studentische Hilfskräfte KW - wissenschaftliche Hilfkräfte Y1 - 2019 ER - TY - GEN T1 - Richtlinie für die Beschäftigung und Vergütung studentischer und wissenschaftlicher Hilfskräfte an der Fachhochschule Aachen : vom 20. November 2019 aktualisiert am 24. November 2022 T3 - FH-Mitteilungen - 125b/2019 KW - Amtliche Mitteilung KW - Richtlinie KW - studentische Hilfskräfte KW - wissenschaftliche Hilfkräfte Y1 - 2019 ER - TY - GEN T1 - Gleichstellungsquoten der FH Aachen für die Jahre 2019 –2021 : vom 20. November 2019 T3 - FH-Mitteilungen - 126/2019 KW - Amtliche Mitteilung KW - Gleichstellungsquoten KW - 2019 KW - 2020 KW - 2021 Y1 - 2019 ER - TY - GEN T1 - Ordnung zur Aufhebung der Prüfungsordnungen für den Masterstudiengang „Nuclear Applications“ vom 13. Februar 2004 (FH-Mitteilung Nr. 5/2004) und vom 25. Februar 2010 (FH-Mitteilung Nr. 15/2010) in den Fassungen der Bekanntmachung der Änderungsordnungen vom 6. November 2012 (FH-Mitteilung Nr. 120/2012), 18. Juni 2014 (FH- Mitteilung Nr. 72/2014) und vom 15. Juni 2015 (FH-Mitteilung Nr. 28/2015) : vom 29. November 2019 T3 - FH-Mitteilungen - 127/2019 KW - Amtliche Mitteilung KW - Aufhebungsordnung KW - Prüfungsordnung KW - Master KW - Nuclear Applications Y1 - 2023 ER - TY - GEN T1 - 5. Ordnung zur Änderung der Prüfungsordnung für die Bachelorstudiengänge „Betriebswirtschaft Praxis Plus“ und „Betriebswirtschaft Praxis Plus (Teilzeit)“ mit dem Studienabschluss „Bachelor of Science“ am Fachbereich Wirtschaftswissenschaften der Fachhochschule Aachen (PO – BWL Praxis Plus) : vom 29. November 2019 T3 - FH-Mitteilungen - 128/2019 KW - Amtliche Mitteilung KW - Änderungsordnung KW - Prüfungsordnung KW - Bachelor KW - Betriebswirtschaft Praxis Plus Y1 - 2023 ER - TY - GEN T1 - Prüfungsordnung für die Bachelorstudiengänge „Betriebswirtschaft Praxis Plus“ und „Betriebswirtschaft Praxis Plus (Teilzeit)“ mit dem Studienabschluss „Bachelor of Science“ am Fachbereich Wirtschaftswissenschaften der Fachhochschule Aachen (PO-BWL Praxis Plus) : vom 14. Januar 2014 – FH-Mitteilung Nr. 2/2014 in der Fassung der Bekanntmachung der Änderungsordnung vom 29. November 2019 – FH-Mitteilung Nr. 128/2019 (Nichtamtliche lesbare Fassung | Studienbeginn ab WS 2019/20) T3 - FH-Mitteilungen - 129/2019 KW - Amtliche Mitteilung KW - Lesbare Fassung KW - Prüfungsordnung KW - Bachelor KW - Betriebswirtschaft Praxis Plus Y1 - 2023 ER - TY - GEN T1 - 2. Änderung der Richtlinie des Rektorats der FH Aachen für die Vergabe von Lehrveranstaltungsprämien : vom 13. Dezember 2019 T3 - FH-Mitteilungen - 130/2019 KW - Amtliche Mitteilung KW - Änderung KW - Richtlinie KW - Rektorat KW - Lehrveranstaltungsprämien Y1 - 2019 ER - TY - GEN T1 - Richtlinie des Rektorats der FH Aachen für die Vergabe von Lehrveranstaltungsprämien : vom 16. Juli 2012 – FH-Mitteilung Nr. 68/2012 in der Fassung der Bekanntmachung der Änderung vom 13. Dezember 2019 – FH-Mitteilung Nr. 130/2019 (Nichtamtliche lesbare Fassung) T3 - FH-Mitteilungen - 131/2019 KW - Amtliche Mitteilung KW - Lesbare Fassung KW - Richtlinie KW - Rektorat KW - Lehrveranstaltungsprämien Y1 - 2019 ER - TY - GEN T1 - Prüfungsordnung für den Masterstudiengang Nuclear Applications im Fachbereich Chemie und Biotechnologie an der Fachhochschule Aachen : vom 17. Dezember 2019 T3 - FH-Mitteilungen - 132/2019 KW - Amtliche Mitteilung KW - Prüfungsordnung KW - Master KW - Nuclear Applications KW - Chemie und Biotechnologie Y1 - 2019 ER - TY - GEN T1 - Ordnung zur Aufhebung der Prüfungsordnung für den Masterstudiengang „Information Systems Engineering“ vom 22. Januar 2010 (FH-Mitteilung Nr. 5/2010), zuletzt geändert durch Änderungsordnung vom 4. Februar 2013 (FH-Mitteilung Nr. 6/2013) : vom 20. Dezember 2019 T3 - FH-Mitteilungen - 133/2019 KW - Amtliche Mitteilung KW - Aufhebungsordnung KW - Prüfungsordnung KW - Master KW - Information Systems Engineering Y1 - 2019 ER - TY - GEN T1 - Ordnung zur Aufhebung der Prüfungsordnung für den Masterstudiengang „Elektrotechnik“ (zuvor „Nachrichtentechnik“ und „Elektrotechnik und Informationstechnik“) vom 22. Januar 2010 (FH-Mitteilung Nr. 7/2010), zuletzt geändert durch Änderungsordnung vom 25. April 2016 (FH-Mitteilung Nr. 31/2016) : vom 20. Dezember 2019 T3 - FH-Mitteilungen - 134/2019 KW - Amtliche Mitteilung KW - Aufhebungsordnung KW - Prüfungsordnung KW - Master KW - Elektrotechnik Y1 - 2019 ER - TY - GEN T1 - Ordnung zur Aufhebung der Prüfungsordnung für die Masterstudiengänge „Energiewirtschaft & Informatik“ (3 Semester) und „Energiewirtschaft & Informatik“ (4 Semester) vom 4. Mai 2016 (FH-Mitteilung Nr. 59/2016) Fachbereich Energietechnik Fachbereich Medizintechnik und Technomathematik an der Fachhochschule Aachen : vom 16. Januar 2020 T3 - FH-Mitteilungen - 1/2020 KW - Amtliche Mitteilung KW - Aufhebungsordnung KW - Prüfungsordnung KW - Master KW - Energiewirtschaft & Informatik Y1 - 2020 ER - TY - GEN T1 - Verwaltungs- und Benutzungsordnung des Solar-Instituts Jülich (SIJ) : vom 27. Januar 2020 T3 - FH-Mitteilungen - 2/2020 KW - Amtliche Mitteilung KW - Verwaltungs- und Benutzungsordnung KW - Solar-Institut Jülich KW - SIJ Y1 - 2020 ER - TY - GEN T1 - Verwaltungs- und Benutzungsordnung des Solar-Instituts Jülich (SIJ) vom 27. Januar 2020 : berichtigt durch Bekanntmachung vom 18. März 2020 (FH-Mitteilung Nr. 27/2020) T3 - FH-Mitteilungen - 2b/2020 KW - Amtliche Mitteilung KW - Verwaltungs- und Benutzungsordnung KW - Solar-Institut Jülich KW - SIJ KW - berichtigt Y1 - 2020 ER - TY - CHAP A1 - Maurer, Florian A1 - Miskiw, Kim K. A1 - Acosta, Rebeca Ramirez A1 - Harder, Nick A1 - Sander, Volker A1 - Lehnhoff, Sebastian ED - Jorgensen, Bo Norregaard ED - Pereira da Silva, Luiz Carlos ED - Ma, Zheng T1 - Market abstraction of energy markets and policies - application in an agent-based modeling toolbox T2 - EI.A 2023: Energy Informatics N2 - In light of emerging challenges in energy systems, markets are prone to changing dynamics and market design. Simulation models are commonly used to understand the changing dynamics of future electricity markets. However, existing market models were often created with specific use cases in mind, which limits their flexibility and usability. This can impose challenges for using a single model to compare different market designs. This paper introduces a new method of defining market designs for energy market simulations. The proposed concept makes it easy to incorporate different market designs into electricity market models by using relevant parameters derived from analyzing existing simulation tools, morphological categorization and ontologies. These parameters are then used to derive a market abstraction and integrate it into an agent-based simulation framework, allowing for a unified analysis of diverse market designs. Furthermore, we showcase the usability of integrating new types of long-term contracts and over-the-counter trading. To validate this approach, two case studies are demonstrated: a pay-as-clear market and a pay-as-bid long-term market. These examples demonstrate the capabilities of the proposed framework. KW - Energy market design KW - Agent-based simulation KW - Market modeling Y1 - 2023 SN - 978-3-031-48651-7 (Print) SN - 978-3-031-48652-4 (eBook) U6 - https://doi.org/10.1007/978-3-031-48652-4_10 N1 - Energy Informatics Academy Conference, 6-8 December 23, Campinas, Brazil. N1 - Part of the Lecture Notes in Computer Science book series (LNCS,volume 14468). SP - 139 EP - 157 PB - Springer CY - Cham ER - TY - RPRT A1 - Göll, Fabian A1 - Braunstein, Björn A1 - Albracht, Kirsten T1 - Lernende roboterassistierte Systeme für das neuromuskuläre Training - RoSylerNT; Teilvorhaben: Entwicklung eines neuromuskuloskelettalen Modells als Basis für die Interaktionsfähigkeiten autonomer Assistenzsysteme KW - Robotik KW - Rehabilitationsmedizin KW - Neuromuskuläres System KW - Rehabilitatives Training KW - Trainingsgerät Y1 - 2021 U6 - https://doi.org/10.2314/KXP:1855318741 N1 - Förderkennzeichen BMBF 16SV7853 Schlussbericht der Deutschen Sporthochschule Köln für das Vorhaben RoSylerNT Laufzeit: 01.08.2017-31.07.2021 PB - Deutsche Sporthochschule Köln CY - Köln ER - TY - JOUR A1 - Peterson-Oster, Madeleine A1 - Peterson, Leif Arne T1 - Fassadensystem: Optisch ansprechend, freistehend, elementiert und aus Eichenholz JF - Bauen mit Holz, Der Zimmermann N2 - Bei der Entwicklung des Fassadensystems ging es darum die mögliche Dauerhaftigkeit von Holz bei direkter Bewitterung zu maximieren. Gleichzeitig soll gezeigt werden, dass mittels durchdachter Ansätze beim konstruktiven Holzschutz und die Wahl einer geeigneten Holzart langlebige Konstruktionen realisiert werden können. Y1 - 2020 SN - 0005-6545 PB - Rudolf Müller CY - Köln ER - TY - JOUR A1 - Karschuck, Tobias A1 - Schmidt, Stefan A1 - Achtsnicht, Stefan A1 - Poghossian, Arshak A1 - Wagner, Patrick A1 - Schöning, Michael Josef T1 - Multiplexing system for automated characterization of a capacitive field-effect sensor array JF - Physica Status Solidi A N2 - In comparison to single-analyte devices, multiplexed systems for a multianalyte detection offer a reduced assay time and sample volume, low cost, and high throughput. Herein, a multiplexing platform for an automated quasi-simultaneous characterization of multiple (up to 16) capacitive field-effect sensors by the capacitive–voltage (C–V) and the constant-capacitance (ConCap) mode is presented. The sensors are mounted in a newly designed multicell arrangement with one common reference electrode and are electrically connected to the impedance analyzer via the base station. A Python script for the automated characterization of the sensors executes the user-defined measurement protocol. The developed multiplexing system is tested for pH measurements and the label-free detection of ligand-stabilized, charged gold nanoparticles. KW - Capacitive field-effect sensor KW - Gold nanoparticles KW - Label-free detection KW - Multicell KW - Multiplexing Y1 - 2023 U6 - https://doi.org/10.1002/pssa.202300265 SN - 1862-6300 (Print) SN - 1862-6319 (Online) N1 - Corresponding author: Michael Josef Schöning VL - 220 IS - 22 PB - Wiley-VCH CY - Weinheim ER - TY - JOUR A1 - Janus, Kevin Alexander A1 - Achtsnicht, Stefan A1 - Drinic, Aleksander A1 - Kopp, Alexander A1 - Keusgen, Michael A1 - Schöning, Michael Josef T1 - Transient magnesium-based thin-film temperature sensor on a flexible, bioabsorbable substrate for future medical applications JF - Applied Research N2 - In this work, the bioabsorbable materials, namely fibroin, polylactide acid (PLA), magnesium and magnesium oxide are investigated for their application as transient, resistive temperature detectors (RTD). For this purpose, a thin-film magnesium-based meander-like electrode is deposited onto a flexible, bioabsorbable substrate (fibroin or PLA) and encapsulated (passivated) by additional magnesium oxide layers on top and below the magnesium-based electrode. The morphology of different layered RTDs is analyzed by scanning electron microscopy. The sensor performance and lifetime of the RTD is characterized both under ambient atmospheric conditions between 30°C and 43°C, and wet tissue-like conditions with a constant temperature regime of 37°C. The latter triggers the degradation process of the magnesium-based layers. The 3-layers RTDs on a PLA substrate could achieve a lifetime of 8.5 h. These sensors also show the best sensor performance under ambient atmospheric conditions with a mean sensitivity of 0.48 Ω/°C ± 0.01 Ω/°C. KW - Silk fibroin KW - Polylactide acid KW - Bioabsorbable KW - Resistive temperature detector Y1 - 2023 U6 - https://doi.org/10.1002/appl.202300102 SN - 2702-4288 (Print) N1 - Corresponding author: Michael Josef Schöning IS - Accepted manuscript PB - Wiley-VCH ER - TY - JOUR A1 - Alnemer, Momin Sami Mohammad A1 - Kotliar, Konstantin A1 - Neuhaus, Valentin A1 - Pape, Hans-Christoph A1 - Ciritsis, Bernhard D. T1 - Cost-effectiveness analysis of surgical proximal femur fracture prevention in elderly: a Markov cohort simulation model JF - Cost Effectiveness and Resource Allocation N2 - Background Hip fractures are a common and costly health problem, resulting in significant morbidity and mortality, as well as high costs for healthcare systems, especially for the elderly. Implementing surgical preventive strategies has the potential to improve the quality of life and reduce the burden on healthcare resources, particularly in the long term. However, there are currently limited guidelines for standardizing hip fracture prophylaxis practices. Methods This study used a cost-effectiveness analysis with a finite-state Markov model and cohort simulation to evaluate the primary and secondary surgical prevention of hip fractures in the elderly. Patients aged 60 to 90 years were simulated in two different models (A and B) to assess prevention at different levels. Model A assumed prophylaxis was performed during the fracture operation on the contralateral side, while Model B included individuals with high fracture risk factors. Costs were obtained from the Centers for Medicare & Medicaid Services, and transition probabilities and health state utilities were derived from available literature. The baseline assumption was a 10% reduction in fracture risk after prophylaxis. A sensitivity analysis was also conducted to assess the reliability and variability of the results. Results With a 10% fracture risk reduction, model A costs between $8,850 and $46,940 per quality-adjusted life-year ($/QALY). Additionally, it proved most cost-effective in the age range between 61 and 81 years. The sensitivity analysis established that a reduction of ≥ 2.8% is needed for prophylaxis to be definitely cost-effective. The cost-effectiveness at the secondary prevention level was most sensitive to the cost of the contralateral side’s prophylaxis, the patient’s age, and fracture treatment cost. For high-risk patients with no fracture history, the cost-effectiveness of a preventive strategy depends on their risk profile. In the baseline analysis, the incremental cost-effectiveness ratio at the primary prevention level varied between $11,000/QALY and $74,000/QALY, which is below the defined willingness to pay threshold. Conclusion Due to the high cost of hip fracture treatment and its increased morbidity, surgical prophylaxis strategies have demonstrated that they can significantly relieve the healthcare system. Various key assumptions facilitated the modeling, allowing for adequate room for uncertainty. Further research is needed to evaluate health-state-associated risks. KW - Hip fractures KW - Prevention KW - Geriatric KW - Cost-effectiveness KW - Prophylaxis Y1 - 2023 U6 - https://doi.org/10.1186/s12962-023-00482-4 SN - 1478-7547 N1 - Corresponding author: Momin S. Alnemer IS - 21, Article number: 77 PB - Springer Nature ER - TY - JOUR A1 - Sildatke, Michael A1 - Karwanni, Hendrik A1 - Kraft, Bodo A1 - Zündorf, Albert T1 - A distributed microservice architecture pattern for the automated generation of information extraction pipelines JF - SN Computer Science N2 - Companies often build their businesses based on product information and therefore try to automate the process of information extraction (IE). Since the information source is usually heterogeneous and non-standardized, classic extract, transform, load techniques reach their limits. Hence, companies must implement the newest findings from research to tackle the challenges of process automation. They require a flexible and robust system that is extendable and ensures the optimal processing of the different document types. This paper provides a distributed microservice architecture pattern that enables the automated generation of IE pipelines. Since their optimal design is individual for each input document, the system ensures the ad-hoc generation of pipelines depending on specific document characteristics at runtime. Furthermore, it introduces the automated quality determination of each available pipeline and controls the integration of new microservices based on their impact on the business value. The introduced system enables fast prototyping of the newest approaches from research and supports companies in automating their IE processes. Based on the automated quality determination, it ensures that the generated pipelines always meet defined business requirements when they come into productive use. KW - Architectural design KW - Model-driven software engineering KW - Software and systems modeling KW - Enterprise information systems KW - Information extraction Y1 - 2023 U6 - https://doi.org/10.1007/s42979-023-02256-4 SN - 2661-8907 N1 - Corresponding authors: Michael Sildatke, Hendrik Karwanni IS - 4, Article number: 833 PB - Springer Singapore CY - Singapore ER - TY - JOUR A1 - Thomessen, Karolin A1 - Thoma, Andreas A1 - Braun, Carsten T1 - Bio-inspired altitude changing extension to the 3DVFH* local obstacle avoidance algorithm JF - CEAS Aeronautical Journal N2 - Obstacle avoidance is critical for unmanned aerial vehicles (UAVs) operating autonomously. Obstacle avoidance algorithms either rely on global environment data or local sensor data. Local path planners react to unforeseen objects and plan purely on local sensor information. Similarly, animals need to find feasible paths based on local information about their surroundings. Therefore, their behavior is a valuable source of inspiration for path planning. Bumblebees tend to fly vertically over far-away obstacles and horizontally around close ones, implying two zones for different flight strategies depending on the distance to obstacles. This work enhances the local path planner 3DVFH* with this bio-inspired strategy. The algorithm alters the goal-driven function of the 3DVFH* to climb-preferring if obstacles are far away. Prior experiments with bumblebees led to two definitions of flight zone limits depending on the distance to obstacles, leading to two algorithm variants. Both variants reduce the probability of not reaching the goal of a 3DVFH* implementation in Matlab/Simulink. The best variant, 3DVFH*b-b, reduces this probability from 70.7 to 18.6% in city-like worlds using a strong vertical evasion strategy. Energy consumption is higher, and flight paths are longer compared to the algorithm version with pronounced horizontal evasion tendency. A parameter study analyzes the effect of different weighting factors in the cost function. The best parameter combination shows a failure probability of 6.9% in city-like worlds and reduces energy consumption by 28%. Our findings demonstrate the potential of bio-inspired approaches for improving the performance of local path planning algorithms for UAV. KW - UAV KW - Obstacle avoidance KW - Autonomy KW - Local path planning Y1 - 2023 U6 - https://doi.org/10.1007/s13272-023-00691-w SN - 1869-5590 (Online) SN - 1869-5582 (Print) N1 - Corresponding author: Karolin Thomessen PB - Springer CY - Wien ER - TY - JOUR A1 - Digel, Ilya A1 - Akimbekov, Nuraly S. A1 - Rogachev, Evgeniy A1 - Pogorelova, Natalia T1 - Bacterial cellulose produced by Medusomyces gisevii on glucose and sucrose: biosynthesis and structural properties JF - Cellulose N2 - In this work, the effects of carbon sources and culture media on the production and structural properties of bacterial cellulose (BC) synthesized by Medusomyces gisevii have been studied. The culture medium was composed of different initial concentrations of glucose or sucrose dissolved in 0.4% extract of plain green tea. Parameters of the culture media (titratable acidity, substrate conversion degree etc.) were monitored daily for 20 days of cultivation. The BC pellicles produced on different carbon sources were characterized in terms of biomass yield, crystallinity and morphology by field emission scanning electron microscopy (FE-SEM), atomic force microscopy and X-ray diffraction. Our results showed that Medusomyces gisevii had higher BC yields in media with sugar concentrations close to 10 g L−1 after a 18–20 days incubation period. Glucose in general lead to a higher BC yield (173 g L−1) compared to sucrose (163.5 g L−1). The BC crystallinity degree and surface roughness were higher in the samples synthetized from sucrose. Obtained FE-SEM micrographs show that the BC pellicles synthesized in the sucrose media contained densely packed tangles of cellulose fibrils whereas the BC produced in the glucose media displayed rather linear geometry of the BC fibrils without noticeable aggregates. KW - Bacterial cellulose KW - Medusomyces gisevi KW - Carbon sources KW - Culture media KW - Cellulose nanostructure Y1 - 2023 U6 - https://doi.org/10.1007/s10570-023-05592-z SN - 1572-882X (Online) SN - 0969-0239 (Print) N1 - Corresponding author: Ilya Digel PB - Springer Science + Business Media CY - Dordrecht ER - TY - CHAP A1 - Frühwald, Katja A1 - Peterson, Leif Arne A1 - Hasenstab, Andreas ED - Fouad, Nabil A. T1 - Prüfverfahren zur Begutachtung der Materialeigenschaften von Holztragwerken T2 - Bauphysik‐Kalender 2012: Schwerpunkt: Gebäudediagnostik N2 - Dieses Kapitel beinhaltet: - Einleitung - Ausgewählte typische Schäden an Holzbauwerken - Das Material Holz und seine Besonderheiten - Bestandserfassung - Labormethoden - Begutachtungsbeispiele - Zusammenfassung und Schlussfolgerungen - Literatur Y1 - 2012 SN - 9783433029862 (Print) SN - 9783433601235 (Online) U6 - https://doi.org/10.1002/9783433601235.ch4 SP - 103 EP - 155 PB - Ernst & Sohn CY - Berlin ER - TY - BOOK A1 - Holschemacher, Klaus A1 - Peters, Klaus A1 - Peterson, Leif Arne A1 - Schneider, Klaus-Jürgen A1 - Thiele, Ralf T1 - Konstruktiver Ingenieurbau kompakt: Formelsammlung und Bemessungshilfen nach Eurocode für die Bereiche: Lastannahmen, Holzbau, Mauerwerksbau, Stahlbau, Stahlbetonbau, Geotechnik, statische Hinweise N2 - Das kompakte Nachschlagewerk für den konstruktiven Ingenieurbau wurde für den täglichen Gebrauch auf der Baustelle konzipiert und stellt alle für die rechnerische Nachweisführung und Konstruktion von Bauteilen wichtigsten Angaben in Form einer Formelsammlung mit Nachweishilfen zur Verfügung. Der Inhalt wurde auf Basis der neuen Eurocodes komplett aktualisiert und erweitert. Die 4. Auflage enthält in bewährter Manier eine umfangreiche Formelsammlung, Querschnittswerte und Bemessungshilfen zu den Bereichen Lastannahmen, Holzbau, Mauerwerksbau, Stahlbau, Stahlbetonbau, Geotechnik sowie statische Hinweise. Farbiges Papier erleichtert den zielgerichteten Zugriff auf die einzelnen Fachgebiete. Y1 - 2013 SN - 978-3-410-22775-5 PB - Beuth CY - Berlin ET - 4., vollständig überarbeitete Auflage ER - TY - BOOK A1 - Nebgen, Nikolaus A1 - Peterson, Leif Arne T1 - Holzbau kompakt nach Eurocode 5 N2 - "Holzbau kompakt" wurde sowohl für Studierende als auch Praktiker konzipiert und beschränkt sich nicht auf reine Holzbauaufgaben, sondern setzt sich ggf. auch mit der Tragwerkslehre auseinander. Die Neuauflage basiert auf dem Eurocode 5 und berücksichtigt zahlreiche neue Erkenntnisse aus Forschung und praxisnaher Entwicklung. Neben den Grundlagen der Bemessung, der Baustoffe, der Dauerhaftigkeit und des Brandschutzes konzentriert sich das Grundlagenwerk besonders auf das Konstruieren mit Holz und Holzwerkstoffen, anschaulich dargestellt an sehr ausführlichen Beispielen für Wohnhaus und Hallentragwerk. Y1 - 2015 SN - 978-3-410-25455-3 PB - Beuth CY - Berlin ET - 5. Auflage ER - TY - GEN T1 - Prüfungsordnung für den Masterstudiengang Architektur im Fachbereich Architektur an der Fachhochschule Aachen T3 - FH-Mitteilungen - 69/2019 KW - Amtliche Mitteilung KW - Master KW - Prüfungsordnung KW - Studienbeginn 2018/19 KW - Architektur Y1 - 2019 ER - TY - GEN T1 - 3. Ordnung zur Änderung der Studien- und Prüfungsordnung für den Bachelorstudiengang Bauingenieurwesen (7-semestrig), Bachelorstudiengang Bauingenieurwesen mit Praxissemester (8-semestrig), Bachelorstudiengang Bauingenieurwesen mit Auslandssemester (8-semestrig), Abschluss Bachelor of Engineering T3 - FH-Mitteilungen - 74/2019 KW - Studien- und Prüfungsordnung KW - Änderungsordnung KW - Bachelor KW - Bauingieurwesen KW - Amtliche Mitteilung Y1 - 2019 ER - TY - GEN T1 - 2. Ordnung zur Änderung der Prüfungsordnung für den dualen ausbildungsintegrierenden Bachelorstudiengang „Physiotherapie“ und den berufsbegleitenden Bachelorstudiengang „Physiotherapie“ an der Fachhochschule Aachen in Kooperation mit der Medizinischen Fakultät der Rheinisch-Westfälisch Technischen Hochschule Aachen und der Physiotherapieschule des Universitätsklinikums Aachen (UK Aachen) T3 - FH-Mitteilungen - 72/2019 KW - Amtliche Mitteilung KW - Änderungsordnung KW - Bachelor KW - Prüfungsordnung KW - Physiotherapie Y1 - 2019 ER - TY - GEN T1 - Fremdfirmenrichtlinie der FH Aachen T3 - FH-Mitteilungen - 17/2019 KW - Amtliche Mitteilungen KW - Fremdfirmenrichtlinie Y1 - 2019 ER - TY - GEN T1 - Prüfungsordnung für die Bachelorstudiengänge „Elektrotechnik“ und „Elektrotechnik mit Praxissemester“ im Fachbereich Energietechnik an der FH Aachen : vom 10. Oktober 2019 T3 - FH-Mitteilungen - 99/2019 KW - Amtliche Mitteilung KW - Prüfungsordnung KW - Bachelor KW - Elektrotechnik KW - Energietechnik Y1 - 2019 ER - TY - GEN T1 - Ordnung zur Änderung der Gesamtprüfungsordnung für den Bachelorstudiengang „Elektrotechnik mit Orientierungssemester“ an der Fachhochschule Aachen und der RWTH Aachen : vom 10. Oktober 2019 T3 - FH-Mitteilungen - 100/2019 KW - Amtliche Mitteilung KW - Änderungsordnung KW - Gesamtprüfungsordnung KW - Bachelor KW - Elektrotechnik Y1 - 2019 ER - TY - GEN T1 - Studien- und Prüfungsordnung für den dualen Bachelorstudiengang Bauingenieurwesen – Netzingenieur (9 Semester) und den Bachelorstudiengang Bauingenieurwesen – Netzingenieur (7 Semester) Abschluss Bachelor of Engineering im Fachbereich Bauingenieurwesen an der Fachhochschule Aachen : vom 16. Juli 2012 – FH-Mitteilung Nr. 67/2012 in der Fassung der Bekanntmachung der Änderungsordnung vom 16. August 2019 – FH-Mitteilung Nr. 78/2019 (Nichtamtliche lesbare Fassung, Studienbeginn WS 2014/15–2016/17) T3 - FH-Mitteilungen - 90/2019 KW - Amtliche Mitteilung KW - Lesbare Fassung KW - Studien- und Prüfungsordnung KW - Bachelor KW - Bauingenieurwesen Y1 - 2019 ER - TY - GEN T1 - Studien- und Prüfungsordnung des Studiengangs Bauingenieurwesen – Netzingenieur – Abschluss Bachelor of Engineering – im Fachbereich Bauingenieurwesen an der Fachhochschule Aachen : vom 16. Juli 2012 – FH-Mitteilung Nr. 67/2012 in der Fassung der Bekanntmachung der Änderungsordnung vom 16. August 2019 – FH-Mitteilung Nr. 78/2019 (Nichtamtliche lesbare Fassung | Studienbeginn WS 2011/12–2013/14) T3 - FH-Mitteilungen - 89/2019 KW - Amtliche Mitteilung KW - Lesbare Fassung KW - Studien- und Prüfungsordnung KW - Bachelor KW - Bauingenieurwesen Y1 - 2019 ER - TY - GEN T1 - Studien- und Prüfungsordnung für den dualen Bachelorstudiengang Bauingenieurwesen – Netzingenieur (9 Semester) und den Bachelorstudiengang Bauingenieurwesen – Netzingenieur (7 Semester) Abschluss Bachelor of Engineering im Fachbereich Bauingenieurwesen an der Fachhochschule Aachen : vom 16. Juli 2012 – FH-Mitteilung Nr. 67/2012 in der Fassung der Bekanntmachung der Änderungsordnung vom 16. August 2019 – FH-Mitteilung Nr. 78/2019 (Nichtamtliche lesbare Fassung, Studienbeginn ab WS 2017/18) T3 - FH-Mitteilungen - 91/2019 KW - Amtliche Mitteilung KW - Lesbare Fassung KW - Studien- und Prüfungsordnung KW - Bachelor KW - Bauingenieurwesen Y1 - 2019 ER - TY - GEN T1 - Ordnung zur Aufhebung der Studien- und Prüfungsordnung für den Masterstudiengang „Facility Management“ vom 29. November 2012 (FH-Mitteilung Nr. 127/2012) in der Fassung der Bekanntmachung der Änderungsordnungen vom 3. Februar 2016 (FH-Mitteilung Nr. 10/2016) und 16. August 2019 (FH-Mitteilung Nr. 82/2019) an der Fachhochschule Aachen : vom 24. Juli 2018 – FH-Mitteilung Nr. 122/2018 in der Fassung der Bekanntmachung der Änderungsordnung vom 16. August 2019 – FH-Mitteilung Nr. 83/2019 (Nichtamtliche lesbare Fassung) T3 - FH-Mitteilungen - 97/2019 KW - Amtliche Mitteilung KW - Lesbare Fassung KW - Studien- und Prüfungsordnung KW - Master KW - Facility Management Y1 - 2019 ER - TY - GEN T1 - Prüfungsordnung für den dualen ausbildungsintegrierenden Bachelorstudiengang „Physiotherapie“ und den berufsbegleitenden Bachelorstudiengang „Physiotherapie“ an der Fachhochschule Aachen in Kooperation mit der Medizinischen Fakultät der Rheinisch-Westfälisch Technischen Hochschule Aachen und der Physiotherapieschule des Universitätsklinikums Aachen (UK Aachen) T3 - FH-Mitteilungen - 73/2019 KW - Amtliche Mitteilung KW - Bachelor KW - Prüfungsordnung KW - lesbare Fassung KW - Physiotherapie Y1 - 2019 ER - TY - GEN T1 - Beitragsordnung des Studierendenwerks Aachen (21. Änderung) : vom 3. Juli 2019 T3 - FH-Mitteilungen - 98/2019 KW - Amtliche Mitteilung KW - Beitragsordnung KW - Studierendenwerk Y1 - 2019 ER - TY - GEN T1 - Ordnung zur Regelung der Einstellung des Bachelorstudiengangs Bauingenieurwesen – Netzingenieur (7-semestrig) und des dualen Bachelorstudiengangs Bauingenieurwesen – Netzingenieur (9-semestrig) im Fachbereich Bauingeieurwesen an der Fachhochschule Aachen : vom 24. Juli 2018 – FH-Mitteilung Nr. 123/2018 in der Fassung der Bekanntmachung der Änderungsordnung vom 16. August 2019 – FH-Mitteilung Nr. 79/2019 (Nichtamtliche lesbare Fassung) T3 - FH-Mitteilungen - 92/2019 KW - Amtliche Mitteilung KW - Lesbare Fassung KW - Einstellungsordnung KW - Bachelor KW - Bauingenieurwesen Y1 - 2019 ER - TY - GEN T1 - Studien- und Prüfungsordnung für den Masterstudiengang Bauingenieurwesen – Abschluss Master of Engineering – im Fachbereich Bauingenieurwesen an der Fachhochschule Aachen : vom 10. Dezember 2012 – FH-Mitteilung Nr. 129/2012 in der Fassung der Bekanntmachung der Änderungsordnung vom 16. August 2019 – FH-Mitteilung Nr. 80/2019 (Nichtamtliche lesbare Fassung) T3 - FH-Mitteilungen - 93/2019 KW - Amtliche Mitteilung KW - Lesbare Fassung KW - Studien- und Prüfungsordnung KW - Master KW - Bauingenieurwesen Y1 - 2019 ER - TY - GEN T1 - Studien- und Prüfungsordnung für den Masterstudiengang Facility Management – Abschluss Master of Engineering – : vom 29. November 2012 – FH-Mitteilung Nr. 127/2012 in der Fassung der Bekanntmachung der Änderungsordnung vom 16. August 2019 – FH-Mitteilung Nr. 82/2019 (Nichtamtliche lesbare Fassung | Studienbeginn WS 2016/17–SS 2018) T3 - FH-Mitteilungen - 96/2019 KW - Amtliche Mitteilung KW - Lesbare Fassung KW - Studien- und Prüfungsordnung KW - Master KW - Facility Management Y1 - 2019 ER - TY - GEN T1 - Studien- und Prüfungsordnung für den Masterstudiengang Facility Management – Abschluss Master of Engineering – : vom 29. November 2012 – FH-Mitteilung Nr. 127/2012 in der Fassung der Bekanntmachung der Änderungsordnung vom 16. August 2019 – FH-Mitteilung Nr. 82/2019 (Nichtamtliche lesbare Fassung, Studienbeginn WS 2012/13–SS 2016) T3 - FH-Mitteilungen - 95/2019 KW - Amtliche Mitteilung KW - Lesbare Fassung KW - Studien- und Prüfungsordnung KW - Master KW - Facility Management Y1 - 2019 ER - TY - GEN T1 - 2. Ordnung zur Änderung der Studien- und Prüfungsordnung für den Masterstudiengang Facility Management – Abschluss Master of Engineering – im Fachbereich Bauingenieurwesen an der Fachhochschule Aachen T3 - FH-Mitteilungen - 82/2019 KW - Amtliche Mitteilung KW - Änderungsordnung KW - Studien- und Prüfungsordnung KW - Master KW - Bauingenieurwesen Y1 - 2019 ER - TY - GEN T1 - Ordnung zur Aufhebung der Studien- und Prüfungsordnung für den Masterstudiengang „Bauingenieurwesen“ vom 10. Dezember 2012 (FH-Mitteilung Nr. 129/2012) in der Fassung der Bekanntmachung der Änderungsordnung vom 30. Mai 2017 (FH-Mitteilung Nr. 58/2017) und 16. August 2019 (FH-Mitteilung Nr. 80/2019) an der Fachhochschule Aachen : vom 24. Juli 2018 – FH-Mitteilung Nr. 121/2018 in der Fassung der Bekanntmachung der Änderungsordnung vom 16. August 2019 – FH-Mitteilung Nr. 81/2019 (Nichtamtliche lesbare Fassung) T3 - FH-Mitteilungen - 94/2019 KW - Amtliche Mitteilung KW - Lesbare Fassung KW - Studien- und Prüfungsordnung KW - Master KW - Bauingenieurwesen Y1 - 2019 ER - TY - GEN T1 - Ordnung zur Änderung der Ordnung zur Aufhebung der Studien- und Prüfungsordnung für die Bachelorstudiengänge „Bauingenieurwesen“ (7-semestrig), „Bauingenieurwesen mit Praxissemester“ (8-semestrig) und „Bauingenieurwesen mit Auslandssemester“ (8-semestrig) vom 1. September 2011 (FH-Mitteilung Nr. 76/2011) in der Fassung der Bekanntmachung der Änderungsordnungen vom 22. August 2013 (FH- Mitteilung Nr. 88/2013) und vom 8. Juni 2016 (FH-Mitteilung Nr. 80/2016) an der Fachhochschule Aachen T3 - FH-Mitteilungen - 75/2019 KW - Amtliche Mitteilung KW - Änderungsordnung KW - Studiengangs- und Prüfungsordnung KW - Bauingenieurwesen KW - Bachelor Y1 - 2019 ER - TY - GEN T1 - 3. Ordnung zur Änderung der Studien- und Prüfungsordnung für den dualen Bachelorstudiengang Bauingenieurwesen, Netzingenieur (9 Semester) und den Bachelorstudiengang Bauingenieurwesen – Netzingenieur (7 Semester) Abschluss Bachelor of Engineering im Fachbereich Bauingenieurwesen an der Fachhochschule Aachen T3 - FH-Mitteilungen - 78/2019 KW - Amtliche Mitteilung KW - Änderungsordnung KW - Studien- und Prüfungsordnung KW - Bachelor KW - Bauingenieurwesen Y1 - 2019 ER - TY - GEN T1 - Ordnung zur Änderung der Ordnung zur Aufhebung der Studien- und Prüfungsordnung für die Bachelorstudiengänge „Bauingenieurwesen“ (7-semestrig), „Bauingenieurwesen mit Praxissemester“ (8-semestrig) und „Bauingenieurwesen mit Auslandssemester“ (8-semestrig) vom 1. September 2011 (FH-Mitteilung Nr. 76/2011) in der Fassung der Bekanntmachung der Änderungsordnungen vom 22. August 2013 (FH- Mitteilung Nr. 88/2013) und vom 8. Juni 2016 (FH-Mitteilung Nr. 80/2016) an der Fachhochschule Aachen T3 - FH-Mitteilungen - 76/2019 KW - Amtliche Mitteilung KW - Studien- und Prüfungsordnung KW - Änderungsordnung KW - Holzingenieurwesen KW - Bachelor Y1 - 2019 ER - TY - GEN T1 - Ordnung zur Änderung der Ordnung zur Aufhebung der Studien- und Prüfungsordnung für den Bachelorstudiengang „Holzingenieurwesen“ (7-semestrig) vom 16. Juli 2012 (FH-Mitteilung Nr. 66/2012) in der Fassung der Bekanntmachung der Änderungsordnung vom 6. Juli 2016 (FH-Mitteilung Nr. 95/2016) an der Fachhochschule Aachen T3 - FH-Mitteilungen - 77/2019 KW - Amtliche Mitteilung KW - Änderungsordnung KW - Studien- und Prüfungsordnung KW - Holzingenieurwesen KW - Bachelor Y1 - 2019 ER - TY - JOUR A1 - Berg-Postweiler, Julia A1 - Steuer-Dankert, Linda A1 - Leicht-Scholten, Carmen T1 - One size does not fit all: Applying antibias trainings in academia JF - The International Journal of Organizational Diversity N2 - Antibias training is increasingly demanded and practiced in academia and industry to increase employees’ sensitivity to discrimination, racism, and diversity. Under the heading of “Diversity Management,” antibias trainings are mainly offered as one-off workshops intending to raise awareness of unconscious biases, create a diversity-affirming corporate culture, promote awareness of the potential of diversity, and ultimately enable the reflection of diversity in development processes. However, coming from childhood education, research and scientific articles on the sustainable effectiveness of antibias in adulthood, especially in academia, are very scarce. In order to fill this research gap, the article aims to explore how sustainable the effects of individual antibias trainings on participants’ behavior are. In order to investigate this, participant observation in a qualitative pre–post setting was conducted, analyzing antibias training in an academic context. Two observers actively participated in the training sessions and documented the activities and reflection processes of the participants. Overall, the results question the effectiveness of single antibias trainings and show that a target-group adaptive approach is mandatory owing to the background of the approach in early childhood education. Therefore, antibias work needs to be adapted to the target group’s needs and realities of life. Furthermore, the study reveals that single antibias trainings must be embedded in a holistic diversity management approach to stimulate sustainable reflection processes among the target group. This article is one of the first to scientifically evaluate antibias training effectiveness, especially in engineering sciences and the university context. KW - Antibias KW - Diversity Management KW - Organizational Culture KW - Engineering Habitus Y1 - 2023 U6 - https://doi.org/10.18848/2328-6261/CGP/v24i01/1-23 SN - 2328-6261 (Print) SN - 2328-6229 (Online) VL - 24 IS - 1 SP - 1 EP - 23 PB - Common Ground Research Networks ER - TY - GEN T1 - Ordnung zur Änderung der Ordnung zur Regelung der Einstellung des Bachelorstudiengangs Bauingenieurwesen – Netzingenieur (7-semestrig) und des dualen Bachelorstudiengangs Bauingenieurwesen – Netzingenieur (9-semestrig) im Fachbereich Bauingeieurwesen an der Fachhochschule Aachen T3 - FH-Mitteilungen - 79/2019 KW - Amtliche Mitteilung KW - Änderungsordnung KW - Einstellungsordnung KW - Bachelor KW - Bauingenieurwesen Y1 - 2019 ER - TY - GEN T1 - 2. Ordnung zur Änderung der Studien- und Prüfungsordnung für den Masterstudiengang Bauingenieurwesen – Abschluss Master of Engineering – im Fachbereich Bauingenieurwesen an der Fachhochschule Aachen T3 - FH-Mitteilungen - 80/2019 KW - Amtliche Mitteilung KW - Änderungsordnung KW - Studien- und Prüfungsordnung KW - Master KW - Bauingenieurwesen Y1 - 2019 ER - TY - GEN T1 - Gesamtprüfungsordnung für den Bachelorstudiengang „Elektrotechnik mit Orientierungssemester“ an der Fachhochschule Aachen und der RWTH Aachen : vom 21. November 2018 – FH-Mitteilung Nr. 165/2018 in der Fassung der Bekanntmachung der Änderungsordnung vom 10. Oktober 2019 – FH-Mitteilung Nr. 100/2019 (Nichtamtliche lesbare Fassung) T3 - FH-Mitteilungen - 101/2019 KW - Amtliche Mitteilung KW - Lesbare Fassung KW - Gesamtprüfungsordnung KW - Bachelor KW - Elektrotechnik Y1 - 2019 ER - TY - GEN T1 - 2. Ordnung zur Änderung der Prüfungsordnung für den Masterstudiengang „Wirtschaftsingenieurwesen“ an der Fachhochschule Aachen : vom 14. Oktober 2019 T3 - FH-Mitteilungen - 102/2019 KW - Amtliche Mitteilung KW - Änderungsordnung KW - Prüfungsordnung KW - Master KW - Wirtschaftsingenieurwesen Y1 - 2023 ER - TY - GEN T1 - Prüfungsordnung für den Masterstudiengang „Wirtschaftsingenieurwesen“ an der Fachhochschule Aachen : vom 11. Dezember 2014 – FH-Mitteilung Nr. 152/2014 in der Fassung der bekanntmachung der Änderungsordnung vom 14. Oktober 2019 – FH-Mitteilung Nr. 102/2019 (Nichtamtliche lesbare Fassung) T3 - FH-Mitteilungen - 103/2019 KW - Amtliche Mitteilung KW - Lesbare Fassung KW - Prüfungsordnung KW - Master KW - Wirtschaftsingenieurwesen Y1 - 2019 ER - TY - JOUR A1 - Nabil, F. A1 - Peterson, Leif Arne A1 - Schmidt, A. A1 - Geerdes, D. T1 - Die Holzkuppel des Neuen Palais in Potsdam JF - Bauingenieur Y1 - 2010 SN - 0005-6650 VL - 85 IS - 8 SP - 324 EP - 330 PB - Springer-VDI-Verlag CY - Düsseldorf ER - TY - JOUR A1 - El Bergui, Omnia A1 - Abouabdillah, Aziz A1 - Bourioug, Mohamed A1 - Schmitz, Dominik A1 - Biel, Markus A1 - Aboudrare, Abdellah A1 - Krauss, Manuel A1 - Jomaa, Ahlem A1 - Romuli, Sebastian A1 - Müller, Joachim A1 - Fagroud, Mustapha A1 - Bouabid, Rachid T1 - Innovative solutions for drought: Evaluating hydrogel application on onion cultivation (Allium cepa) in Morocco JF - Water N2 - Throughout the last decade, and particularly in 2022, water scarcity has become a critical concern in Morocco and other Mediterranean countries. The lack of rainfall during spring was worsened by a succession of heat waves during the summer. To address this drought, innovative solutions, including the use of new technologies such as hydrogels, will be essential to transform agriculture. This paper presents the findings of a study that evaluated the impact of hydrogel application on onion (Allium cepa) cultivation in Meknes, Morocco. The treatments investigated in this study comprised two different types of hydrogel-based soil additives (Arbovit® polyacrylate and Huminsorb® polyacrylate), applied at two rates (30 and 20 kg/ha), and irrigated at two levels of water supply (100% and 50% of daily crop evapotranspiration; ETc). Two control treatments were included, without hydrogel application and with both water amounts. The experiment was conducted in an open field using a completely randomized design. The results indicated a significant impact of both hydrogel-type dose and water dose on onion plant growth, as evidenced by various vegetation parameters. Among the hydrogels tested, Huminsorb® Polyacrylate produced the most favorable outcomes, with treatment T9 (100%, HP, 30 kg/ha) yielding 70.55 t/ha; this represented an increase of 11 t/ha as compared to the 100% ETc treatment without hydrogel application. Moreover, the combination of hydrogel application with 50% ETc water stress showed promising results, with treatment T4 (HP, 30 kg, 50%) producing almost the same yield as the 100% ETc treatment without hydrogel while saving 208 mm of water. KW - water economy KW - yield KW - deficit irrigation KW - hydrogel KW - onion Y1 - 2023 U6 - https://doi.org/10.3390/w15111972 VL - 15 IS - 11 PB - MDPI CY - Basel ER - TY - THES A1 - Peterson, Leif Arne T1 - Zum Tragverhalten nachgiebig verbundener Biegeträger aus Holz N2 - In der vorliegenden Dissertation werden zunächst die linear elastischen Bemessungsmöglichkeiten für nachgiebig verbundene Biegeträger unter statischer und dynamischer Beanspruchung diskutiert. Zum Vergleich wurden praktische Untersuchungen an zweiteiligen Kantholzbiegeträgem mit mechanischen Verbindungsmitteln unterschiedlicher Verformungscharakteristika durchgeführt, ebenso wie umfangreiche Materialprüfungen an den zusammengefügten Einzelquerschnitten. Hierdurch werden die Unterschiede zum realen, nicht elastischen, statischen Tragverhalten aufgezeigt. Der für das dynamische Verhalten maßgebende Systemparameter der Eigenfrequenz wird für mehrteilige Biegeträger theoretisch hinterfragt und an den nachgiebig verbundenen Kantholzbiegeträgem gemessen. Begleitet von weiteren praktischen Untersuchungen an einzelnen Verbindungsmitteln unter Blockscherbeanspruchung wird die rechnerische Berücksichtigung des plastischen Verbindungsmittelverhaltens auf zwei theoretischen Wegen erforscht. Auf Grundlage der Untersuchungen wird ein neues, semianalytisches y-Verfahren entwickelt. Gegenüber den Berechnungen mit finiten Volumen- und Kontakt-Elementen erweist sich das neue Verfahren auf Basis der, um die schubweichen Fugen erweiterten, Balkentheorie als leistungsfähiger. Der Einfluss des plastischen Verbindungsmittelverhaltens wird durch vergleichende Parameterstudien mit diesem neuen Verfahren als vom anerkannten Stand der Technik ausreichend berücksichtigt identifiziert. Für die linear elastische Dimensionierung werden optimierte Verbindungsmittelanordnungen hergeleitet, die durch übersichtliche Ergänzungen zum existierenden Bemessungskonzept des y-Verfahrens eine exaktere Berechnung ermöglichen. Y1 - 2008 SN - 9783816775973 N1 - Berichte des Instituts für Bauphysik, Band 1 PB - Fraunhofer IRB Verlag CY - Stuttgart ER - TY - JOUR A1 - Lepke, Dietrich A1 - Lillie, Dirk A1 - Peterson, Leif Arne A1 - Hempe, Thomas T1 - Liegedauer von Holzschwellen in Tunneln der Hamburger Hochbahn AG JF - EI - Der Eisenbahningenieur N2 - Die Hamburger Hochbahn AG benötigte im Rahmen der Überarbeitung einer langfristigen Instandhaltungs- und Erneuerungsstrategie für ihre U-Bahn-Infrastruktur eine belastbare Aussage über die Restlebensdauer der Holzschwellen im Tunnel. Aus diesem Grunde beauftragte sie das Institut für Verkehrswesen, Eisenbahnbau und -betrieb (IVE) der Universität Hannover mit der Erstellung eines entsprechenden Gutachtens. Das Ergebnis führte zu der gesicherten Aussage einer erheblich längeren Restlebensdauer der Tunnelschwellen gegenüber den bisherigen, geschätzten Annahmen. Y1 - 2006 SN - 0013-2810 IS - 2 SP - 46 EP - 50 PB - DVV Media Group CY - Hamburg ER - TY - THES A1 - Garcia Lange, Ayari T1 - FIELDPRO : Integrated equipment system for traveling journalists N2 - In today's ultra-connected world, the significance of audio-visual documentation is rapidly growing. Technological advancements have made it more accessible to obtain powerful and compact audio-visual equipment, thereby reducing the dependency on a larger team for the documentation process. This has favoured the development of what is known as backpack journalism. This project meets an unmet market need and presents an opportunity for innovative product development. It focuses on backpack journalists working in remote and challenging conditions with unpredictable transportation and working conditions. The proposed backpack design addresses both transport and working setups. Offering a robust and waterproof yet overall lightweight construction for easy equipment carrying, while also providing an extension of the workspace for essential gear. KW - Produktdesign KW - Medienjournalist KW - Rucksack KW - Hardcase KW - Abgelegene Gebiete Y1 - 2023 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER - TY - THES A1 - Kleen, Mareike T1 - Pendelleuchte aus Glas N2 - Glas ist seit jeher ein faszinierender Werkstoff. Es findet Anwendung in zahlreichen Gebieten und bietet als Material für Leuchten eine besondere Eleganz. Die Pendelleuchte „Calice di fiori“ vereint handwerkliche Kunstfertigkeit und komfortables Design. Sie ist aus mundgeblasenem Glas gefertigt und verleiht durch ihre Färbung eine kraftvolle und dynamische Atmosphäre im Raum. Das besondere Merkmal der Pendelleuchte ist eine Öffnung, die eine einfache und intuitive Montage erleichtert. Die Pendelleuchte ist mit energieeffizienten LEDs ausgestattet und lässt sich mit einem Smart-Home-System bedienen. Die Lichtintensität und Lichtfarbe können den individuellen Bedürfnissen angepasst werden. „Calice di fiori“ mit schnell abnehmbarem Leuchtenschirm fügt sich in modern eingerichtete Räume ein und bringt einen Hauch Blütenflair mit sich. KW - Pendelleuchte KW - Glas KW - Smart-Home KW - Intuitiv KW - Blütenkelch Y1 - 2023 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER - TY - THES A1 - Kremer, Laura T1 - LittleHabit : die richtige Körperhaltung zur Gewohnheit machen N2 - Der heutige Alltag vieler Menschen ist durch längere Sitz-Einheiten gekennzeichnet, während die körperliche Bewegung vernachlässigt wird. Diese Entwicklung kann einen negativen Einfluss auf die Haltung von Personen und ihre Gesundheit haben. In diesem Fall ist eine korrekte Haltung nicht nur für die körperliche, sondern auch für die psychische Gesundheit von großer Relevanz. Die Bachelorarbeit „LittleHabit“ ermöglicht es, dass bei Kindern die Bewegung nach langen Sitz-Einheiten durch gezieltes Training zur Gewohnheit wird. Hierbei wird zwischen dem Zuhause- und dem Schulbereich differenziert. Zu Hause soll das Kind beim Erledigen der Hausaufgaben durch Animationen und Lichtsignale dazu motiviert werden, Bewegungspausen einzulegen. In der Schule soll dieses Vorhaben in reduzierter Form aufgegriffen und mithilfe von Licht- und Farbsignalen umgesetzt werden. Darüber hinaus fördert es die intrinsische Motivation, sodass Kinder aus eigenem Antrieb ein Interesse dafür entwickeln, sich nach langen Sitz-Einheiten zu bewegen. LittleHabit setzt einen Baustein für die Entwicklung einer gesunden Sitz-Haltung und zielt darauf ab, Haltungsschwächen zu verhindern. KW - Produktdesign KW - Haltungsschwäche KW - Kindererziehung KW - Motivation KW - GewohnheitDerHaltung Y1 - 2023 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER - TY - THES A1 - Özmen, Emel T1 - ALIGN : ein adaptives Regalsystem N2 - „ALIGN“ ist ein smartes Möbelsystem, das den individuellen Lebensstil und die Werte der heutigen Gesellschaft widerspiegelt. Es bietet ausreichend Stauraum und ermöglicht es, Objekte gezielt in Szene zu setzen oder in den Hintergrund zu rücken. Das vielseitige System passt sich an unterschiedliche Raum- und Nutzungsszenarien an. Es ermöglicht die individuelle Gestaltung des Wohnraums nach persönlichen Vorlieben und hilft, den Herausforderungen des modernen Lebens gerecht zu werden. „ALIGN“ – eine passende Lösung für jedes Problem. KW - Regalsystem KW - Nachhaltigkeit KW - Minimalismus KW - Modular KW - Abwechslung Y1 - 2023 PB - FH Aachen CY - Aachen ER - TY - JOUR A1 - Abbas, Karim A1 - Balc, Nicolae A1 - Bremen, Sebastian A1 - Skupin, Marco T1 - Crystallization and aging behavior of polyetheretherketone PEEK within rapid tooling and rubber molding JF - Journal of Manufacturing and Materials Processing N2 - In times of short product life cycles, additive manufacturing and rapid tooling are important methods to make tool development and manufacturing more efficient. High-performance polymers are the key to mold production for prototypes and small series. However, the high temperatures during vulcanization injection molding cause thermal aging and can impair service life. The extent to which the thermal stress over the entire process chain stresses the material and whether it leads to irreversible material aging is evaluated. To this end, a mold made of PEEK is fabricated using fused filament fabrication and examined for its potential application. The mold is heated to 200 ◦C, filled with rubber, and cured. A differential scanning calorimetry analysis of each process step illustrates the crystallization behavior and first indicates the material resistance. It shows distinct cold crystallization regions at a build chamber temperature of 90 ◦C. At an ambient temperature above Tg, crystallization of 30% is achieved, and cold crystallization no longer occurs. Additional tensile tests show a decrease in tensile strength after ten days of thermal aging. The steady decrease in recrystallization temperature indicates degradation of the additives. However, the tensile tests reveal steady embrittlement of the material due to increasing crosslinking. KW - additive manufacturing KW - fused filament fabrication KW - crystallization KW - polyetheretherketone KW - rapid tooling Y1 - 2022 U6 - https://doi.org/10.3390/jmmp6050093 SN - 2504-4494 N1 - The article belongs to the Special Issue Advances in Injection Molding: Process, Materials and Applications VL - 6 IS - 5 SP - 1 EP - 12 PB - MDPI CY - Basel ER - TY - CHAP A1 - Hüning, Felix A1 - Mund, Cindy T1 - Integration of agile development in standard labs T2 - 51st Annual Conference of the European Society for Engineering Education (SEFI) N2 - In addition to the technical content, modern courses at university should also teach professional skills to enhance the competencies of students towards their future work. The competency driven approach including technical as well as professional skills makes it necessary to find a suitable way for the integration into the corresponding module in a scalable and flexible manner. Agile development, for example, is essential for the development of modern systems and applications and makes use of dedicated professional skills of the team members, like structured group dynamics and communication, to enable the fast and reliable development. This paper presents an easy to integrate and flexible approach to integrate Scrum, an agile development method, into the lab of an existing module. Due to the different role models of Scrum the students have an individual learning success, gain valuable insight into modern system development and strengthen their communication and organization skills. The approach is implemented and evaluated in the module Vehicle Systems, but it can be transferred easily to other technical courses as well. The evaluation of the implementation considers feedback of all stakeholders, students, supervisor and lecturers, and monitors the observations during project lifetime. KW - professional skills KW - active learning KW - lab work KW - Agile development Y1 - 2023 U6 - https://doi.org/10.21427/NK4Z-WS73 N1 - 51st Annual Conference of the European Society for Engineering Education, Technological University Dublin, 10th-14th September, 2023 ER - TY - JOUR A1 - Thiebes, Anja Lena A1 - Klein, Sarah A1 - Zingsheim, Jonas A1 - Möller, Georg H. A1 - Gürzing, Stefanie A1 - Reddemann, Manuel A. A1 - Behbahani, Mehdi A1 - Cornelissen, Christian G. T1 - Effervescent atomizer as novel cell spray technology to decrease the gas-to-liquid ratio JF - pharmaceutics N2 - Cell spraying has become a feasible application method for cell therapy and tissue engineering approaches. Different devices have been used with varying success. Often, twin-fluid atomizers are used, which require a high gas velocity for optimal aerosolization characteristics. To decrease the amount and velocity of required air, a custom-made atomizer was designed based on the effervescent principle. Different designs were evaluated regarding spray characteristics and their influence on human adipose-derived mesenchymal stromal cells. The arithmetic mean diameters of the droplets were 15.4–33.5 µm with decreasing diameters for increasing gas-to-liquid ratios. The survival rate was >90% of the control for the lowest gas-to-liquid ratio. For higher ratios, cell survival decreased to approximately 50%. Further experiments were performed with the design, which had shown the highest survival rates. After seven days, no significant differences in metabolic activity were observed. The apoptosis rates were not influenced by aerosolization, while high gas-to-liquid ratios caused increased necrosis levels. Tri-lineage differentiation potential into adipocytes, chondrocytes, and osteoblasts was not negatively influenced by aerosolization. Thus, the effervescent aerosolization principle was proven suitable for cell applications requiring reduced amounts of supplied air. This is the first time an effervescent atomizer was used for cell processing. KW - tri-lineage differentiation KW - survival KW - twin-fluid atomizer KW - adipose-derived stromal cells (ASCs) KW - cell atomization KW - cell aerosolization Y1 - 2022 U6 - https://doi.org/10.3390/pharmaceutics14112421 N1 - This article belongs to the Special Issue "Stromal, Stem, Signaling Cells: The Multiple Roles and Applications of Mesenchymal Cells" VL - 14 IS - 11 PB - MDPI CY - Basel ER - TY - JOUR A1 - Timme, Michael T1 - Bauliche Veränderungen durch Wohnungseigentümer und die Zustimmung der Gemeinschaft : Zugleich eine Besprechung des BGH, Urt. v. 17.3.2023 – V ZR 140/22, MDR 2023, 619 JF - Monatsschrift für Deutsches Recht N2 - Durch das WEMoG (Gesetz v. 16.10.2020, BGBl. I 2187) hat der Gesetzgeber die Regelung des § 20 WEG eingeführt. Demnach ist auch für bauliche Veränderungen an Räumen und Flächen, die einem Sondernutzungsrecht unterliegen, die Zustimmung der Gemeinschaft notwendig. Der BGH hat nun mit Urt. v. 17.3.2023 –V ZR 140/22, MDR 2023, 619 deutlich gemacht, dass bei Fehlen eines entsprechenden Beschlusses, die bauliche Veränderung durch einen einzelnen Wohnungseigentümer nicht vorgenommen werden darf, sondern eine rechtswidrige Eigentumsbeeinträchtigung darstellt. Der folgende Beitrag nimmt die Entscheidung zum Anlass, um die neue Rechtslage durch § 20 WEG eingehend zu erläutern. Gleichzeitig werden die Folgen der aktuellen Entscheidung näher dargestellt. Y1 - 2023 SN - 2194-4202 (online) SN - 0340-1812 (print) VL - 77 IS - 13 SP - 815 EP - 818 PB - Verlag Dr. Otto Schmidt CY - Köln ER - TY - JOUR A1 - Baader, Fabian A1 - Boxberg, Marc S. A1 - Chen, Qian A1 - Förstner, Roger A1 - Kowalski, Julia A1 - Dachwald, Bernd T1 - Field-test performance of an ice-melting probe in a terrestrial analogue environment JF - Icarus N2 - Melting probes are a proven tool for the exploration of thick ice layers and clean sampling of subglacial water on Earth. Their compact size and ease of operation also make them a key technology for the future exploration of icy moons in our Solar System, most prominently Europa and Enceladus. For both mission planning and hardware engineering, metrics such as efficiency and expected performance in terms of achievable speed, power requirements, and necessary heating power have to be known. Theoretical studies aim at describing thermal losses on the one hand, while laboratory experiments and field tests allow an empirical investigation of the true performance on the other hand. To investigate the practical value of a performance model for the operational performance in extraterrestrial environments, we first contrast measured data from terrestrial field tests on temperate and polythermal glaciers with results from basic heat loss models and a melt trajectory model. For this purpose, we propose conventions for the determination of two different efficiencies that can be applied to both measured data and models. One definition of efficiency is related to the melting head only, while the other definition considers the melting probe as a whole. We also present methods to combine several sources of heat loss for probes with a circular cross-section, and to translate the geometry of probes with a non-circular cross-section to analyse them in the same way. The models were selected in a way that minimizes the need to make assumptions about unknown parameters of the probe or the ice environment. The results indicate that currently used models do not yet reliably reproduce the performance of a probe under realistic conditions. Melting velocities and efficiencies are constantly overestimated by 15 to 50 % in the models, but qualitatively agree with the field test data. Hence, losses are observed, that are not yet covered and quantified by the available loss models. We find that the deviation increases with decreasing ice temperature. We suspect that this mismatch is mainly due to the too restrictive idealization of the probe model and the fact that the probe was not operated in an efficiency-optimized manner during the field tests. With respect to space mission engineering, we find that performance and efficiency models must be used with caution in unknown ice environments, as various ice parameters have a significant effect on the melting process. Some of these are difficult to estimate from afar. Y1 - 2023 U6 - https://doi.org/10.1016/j.icarus.2023.115852 N1 - Forschungsdaten hierzu: "Performance data of an ice-melting probe from field tests in two different ice environments" (https://opus.bibliothek.fh-aachen.de/opus4/frontdoor/index/index/docId/10890) IS - 409 PB - Elsevier CY - Amsterdam ER - TY - GEN A1 - Feldmann, Marco A1 - Francke, Gero A1 - Espe, Clemes A1 - Chen, Qian A1 - Baader, Fabian A1 - Boxberg, Marc S. A1 - Sustrate, Anna-Marie A1 - Kowalski, Julia A1 - Dachwald, Bernd T1 - Performance data of an ice-melting probe from field tests in two different ice environments N2 - This dataset was acquired at field tests of the steerable ice-melting probe "EnEx-IceMole" (Dachwald et al., 2014). A field test in summer 2014 was used to test the melting probe's system, before the probe was shipped to Antarctica, where, in international cooperation with the MIDGE project, the objective of a sampling mission in the southern hemisphere summer 2014/2015 was to return a clean englacial sample from the subglacial brine reservoir supplying the Blood Falls at Taylor Glacier (Badgeley et al., 2017, German et al., 2021). The standardized log-files generated by the IceMole during melting operation include more than 100 operational parameters, housekeeping information, and error states, which are reported to the base station in intervals of 4 s. Occasional packet loss in data transmission resulted in a sparse number of increased sampling intervals, which where compensated for by linear interpolation during post processing. The presented dataset is based on a subset of this data: The penetration distance is calculated based on the ice screw drive encoder signal, providing the rate of rotation, and the screw's thread pitch. The melting speed is calculated from the same data, assuming the rate of rotation to be constant over one sampling interval. The contact force is calculated from the longitudinal screw force, which es measured by strain gauges. The used heating power is calculated from binary states of all heating elements, which can only be either switched on or off. Temperatures are measured at each heating element and averaged for three zones (melting head, side-wall heaters and back-plate heaters). KW - Ocean Worlds KW - Icy Moons KW - Cryobot KW - Analogue Environments KW - Melting Efficiency KW - Melting Performance KW - Melting Probe KW - Ice Melting Y1 - 2022 U6 - https://doi.org/10.5281/zenodo.6094866 N1 - Forschungsdaten zu "Field-test performance of an ice-melting probe in a terrestrial analogue environment" (https://opus.bibliothek.fh-aachen.de/opus4/frontdoor/index/index/docId/10889) ER - TY - JOUR A1 - Luft, Angela A1 - Luft, Nils A1 - Arntz, Kristian T1 - A basic description logic for service-oriented architecture in factory planning and operational control in the age of industry 4.0 JF - Applied Sciences N2 - Manufacturing companies across multiple industries face an increasingly dynamic and unpredictable environment. This development can be seen on both the market and supply side. To respond to these challenges, manufacturing companies must implement smart manufacturing systems and become more flexible and agile. The flexibility in operational planning regarding the scheduling and sequencing of customer orders needs to be increased and new structures must be implemented in manufacturing systems’ fundamental design as they constitute much of the operational flexibility available. To this end, smart and more flexible solutions for production planning and control (PPC) are developed. However, scheduling or sequencing is often only considered isolated in a predefined stable environment. Moreover, their orientation on the fundamental logic of the existing IT solutions and their applicability in a dynamic environment is limited. This paper presents a conceptual model for a task-based description logic that can be applied to factory planning, technology planning, and operational control. By using service-oriented architectures, the goal is to generate smart manufacturing systems. The logic is designed to allow for easy and automated maintenance. It is compatible with the existing resource and process allocation logic across operational and strategic factory and production planning. KW - manufacturing data model KW - production planning and control KW - manufacturing flexibility KW - technology planning KW - SOA KW - service-oriented architectures KW - factory planning Y1 - 2023 U6 - https://doi.org/10.3390/app13137610 N1 - This article belongs to the Special Issue "Smart Industrial System" VL - 2023 IS - 13 PB - MDPI CY - Basel ER - TY - JOUR A1 - Abbas, Karim A1 - Hedwig, Lukas A1 - Balc, Nicolae A1 - Bremen, Sebastian T1 - Advanced FFF of PEEK: Infill strategies and material characteristics for rapid tooling JF - Polymers N2 - Traditional vulcanization mold manufacturing is complex, costly, and under pressure due to shorter product lifecycles and diverse variations. Additive manufacturing using Fused Filament Fabrication and high-performance polymers like PEEK offer a promising future in this industry. This study assesses the compressive strength of various infill structures (honeycomb, grid, triangle, cubic, and gyroid) when considering two distinct build directions (Z, XY) to enhance PEEK’s economic and resource efficiency in rapid tooling. A comparison with PETG samples shows the behavior of the infill strategies. Additionally, a proof of concept illustrates the application of a PEEK mold in vulcanization. A peak compressive strength of 135.6 MPa was attained in specimens that were 100% solid and subjected to thermal post-treatment. This corresponds to a 20% strength improvement in the Z direction. In terms of time and mechanical properties, the anisotropic grid and isotropic cubic infill have emerged for use in rapid tooling. Furthermore, the study highlights that reducing the layer thickness from 0.15 mm to 0.1 mm can result in a 15% strength increase. The study unveils the successful utilization of a room-temperature FFF-printed PEEK mold in vulcanization injection molding. The parameters and infill strategies identified in this research enable the resource-efficient FFF printing of PEEK without compromising its strength properties. Using PEEK in rapid tooling allows a cost reduction of up to 70% in tool production. KW - polyetheretherketone (PEEK) KW - rapid tooling KW - infill strategy KW - compression behavior KW - additive manufacturing KW - fused filament fabrication Y1 - 2023 U6 - https://doi.org/10.3390/polym15214293 N1 - This article belongs to the Special Issue "Polymer Materials and Design Processes for Additively Manufactured Products" VL - 2023 IS - 15 PB - MDPI CY - Basel ER - TY - PAT A1 - Hüning, Felix T1 - Sensorvorrichtung zur Erfassung eines Magnetfelds sowie magnetbasiertes Sensorsystem zur Erfassung einer Bewegung eines beweglichen Objekts N2 - Eine Sensorvorrichtung (10;110;210;310;410) zur Erfassung eines Magnetfelds, mit einer Wiegand-Sensoreinheit (12;112;212) umfassend: • - mindestens zwei Wiegand-Drähte (20) und • - eine Spulenanordnung (22;122;222), die die mindestens zwei Wiegand-Drähte (20) radial umschließt und die • • • ein Sensorelement (26;126;226) und • • ein Triggerelement (28;128;228), durch das ein Triggermagnetfeld erzeugbar ist, bildet, ist bekannt. Um ein magnetbasiertes Sensorsystem (300;400) zur Erfassung einer Bewegung eines beweglichen Objekts (301;401) zu ermöglichen, das ohne externe Energieversorgung zuverlässig sowie energieeffizient arbeitet und kostengünstig hergestellt werden kann, ist bei der erfindungsgemäßen Sensorvorrichtung (10;110;210;310;410) eine Wiegand-Triggereinheit (14;14a) vorhanden, umfassend: • - einen Wiegand-Draht (30) und • - eine Trigger-Sensorspule (32), die den Wiegand-Draht (30) radial umschließt, wobei ein erstes Ende der Trigger-Sensorspule (32) der Wiegand-Triggereinheit (14;14a) mit einem ersten Ende des Triggerelements (28;128;228) der Wiegand-Sensoreinheit (12;112;212) elektrisch verbunden ist und ein zweites Ende der Trigger-Sensorspule (32) der Wiegand-Triggereinheit (14;14a) mit einem zweiten Ende des Triggerelements (28;128;228) der Wiegand-Sensoreinheit (12;112;212) elektrisch verbunden ist. Auf diese Weise verstärkt ein in der Trigger-Sensorspule (32) erzeugter Impuls das Gesamtmagnetfeld, das auf die Wiegand-Drähte (20) in der Sensoreinheit einwirkt, derart, dass die Triggefeldstärke aller Wiegand-Drähte (20) überschritten wird und diese im wesentlichen zeitgleich auslösen. Y1 - 2023 N1 - Patent WO2023131396A1 ER - TY - CHAP A1 - Steuer-Dankert, Linda T1 - A crazy little thing called sustainability T2 - 51st Annual Conference of the European Society for Engineering Education (SEFI) N2 - Achieving the 17 Sustainable Development Goals (SDGs) set by the United Nations (UN) in 2015 requires global collaboration between different stakeholders. Industry, and in particular engineers who shape industrial developments, have a special role to play as they are confronted with the responsibility to holistically reflect sustainability in industrial processes. This means that, in addition to the technical specifications, engineers must also question the effects of their own actions on an ecological, economic and social level in order to ensure sustainable action and contribute to the achievement of the SDGs. However, this requires competencies that enable engineers to apply all three pillars of sustainability to their own field of activity and to understand the global impact of industrial processes. In this context, it is relevant to understand how industry already reflects sustainability and to identify competences needed for sustainable development. KW - Transformative Competencies KW - Future Skills KW - Transdisciplinarity KW - Interdisciplinarity KW - Sustainability Y1 - 2023 U6 - https://doi.org/10.21427/9CQR-VC94 N1 - 51st Annual Conference of the European Society for Engineering Education, Technological University Dublin, 10th-14th September, 2023 ER - TY - CHAP A1 - Engelmann, Ulrich M. ED - Lindinger, Markus ED - Bartsch, Oliver T1 - Moderationsexpertise – Onlinemoderation T2 - IT-Servicemanagement N2 - Damit Sie auch in den immer häufiger werdenden Onlineveranstaltungen als Moderator gut bestehen, sollten Sie wissen, was bei der Onlinemoderation im Besonderen zu beachten ist. In diesem dritten Teil der Beitragsserie erfahren Sie, warum online anders als offline ist. Die technischen Möglichkeiten werden vorgestellt und auch wie diese zu nutzen sind. Schließlich erhalten Sie Tipps, die Sie beim Sprechen online beachten sollten. Y1 - 2023 SN - 978-3-8249-1154-7 SP - Kapitel 05532 PB - TÜV-Verlag CY - Köln ER - TY - CHAP A1 - Engelmann, Ulrich M. A1 - Baumann, Martin ED - Herbig, Nicola ED - Poppelreuter, Stefan T1 - Moderationsexpertise für QMBs – Onlinemoderation T2 - Qualitätsmanagement im Gesundheitswesen N2 - Damit Sie auch in den immer häufiger werdenden Onlineveranstaltungen als Moderator gut bestehen, sollten Sie wissen, was bei der Onlinemoderation im Besonderen zu beachten ist. In diesem dritten Teil der Beitragsserie erfahren Sie, warum online anders als offline ist. Die technischen Möglichkeiten werden vorgestellt und auch wie diese zu nutzen sind. Schließlich erhalten Sie Tipps, die Sie beim Sprechen online beachten sollten. Y1 - 2023 SN - 978-3-8249-0714-4 SP - Kapitel 10816 PB - TÜV-Verlag CY - Köln ER - TY - BOOK A1 - Lauth, Jakob T1 - Physical chemistry in a nutshell: Basics for engineers and scientists N2 - This book is based on a multimedia course for biological and chemical engineers, which is designed to trigger students' curiosity and initiative. A solid basic knowledge of thermodynamics and kinetics is necessary for understanding many technical, chemical, and biological processes. The one-semester basic lecture course was divided into 12 workshops (chapters). Each chapter covers a practically relevant area of physical chemistry and contains the following didactic elements that make this book particularly exciting and understandable: - Links to Videos at the start of each chapter as preparation for the workshop - Key terms (in bold) for further research of your own - Comprehension questions and calculation exercises with solutions as learning checks - Key illustrations as simple, easy-to-replicate blackboard pictures Humorous cartoons for each workshop (by Faelis) additionally lighten up the text and facilitate the learning process as a mnemonic. To round out the book, the appendix includes a summary of the most popular experiments in basic physical chemistry courses, as well as suggestions for designing workshops with exhibits, experiments, and "questions of the day." Suitable for students minoring in chemistry; chemistry majors are sure to find this slimmed-down, didactically valuable book helpful as well. The book is excellent for self-study. KW - Physical chemistry KW - Thermodynamics as minor KW - Physical chemistry starters KW - Minor chemistry KW - Physical chemistry basics Y1 - 2023 SN - 978-3-662-67636-3 (Softcover) SN - 978-3-662-67637-0 (eBook) U6 - https://doi.org/10.1007/978-3-662-67637-0 PB - Springer CY - Berlin ER - TY - CHAP A1 - Nierle, Elisabeth A1 - Pieper, Martin T1 - Measuring social impacts in engineering education to improve sustainability skills T2 - European Society for Engineering Education (SEFI) N2 - In times of social climate protection movements, such as Fridays for Future, the priorities of society, industry and higher education are currently changing. The consideration of sustainability challenges is increasing. In the context of sustainable development, social skills are crucial to achieving the United Nations Sustainable Development Goals (SDGs). In particular, the impact that educational activities have on people, communities and society is therefore coming to the fore. Research has shown that people with high levels of social competence are better able to manage stressful situations, maintain positive relationships and communicate effectively. They are also associated with better academic performance and career success. However, especially in engineering programs, the social pillar is underrepresented compared to the environmental and economic pillars. In response to these changes, higher education institutions should be more aware of their social impact - from individual forms of teaching to entire modules and degree programs. To specifically determine the potential for improvement and derive resulting change for further development, we present an initial framework for social impact measurement by transferring already established approaches from the business sector to the education sector. To demonstrate the applicability, we measure the key competencies taught in undergraduate engineering programs in Germany. The aim is to prepare the students for success in the modern world of work and their future contribution to sustainable development. Additionally, the university can include the results in its sustainability report. Our method can be applied to different teaching methods and enables their comparison. KW - Social impact measurement KW - Key competences KW - Sustainable engineering education KW - Future skills Y1 - 2023 U6 - https://doi.org/10.21427/QPR4-0T22 N1 - 51st Annual Conference of the European Society for Engineering Education, Technological University Dublin, 10th-14th September, 2023 N1 - Corresponding Author: Elisabeth Nierle ER - TY - JOUR A1 - Haeger, Gerrit A1 - Probst, Johanna A1 - Jaeger, Karl-Erich A1 - Bongaerts, Johannes A1 - Siegert, Petra T1 - Novel aminoacylases from Streptomyces griseus DSM 40236 and their recombinant production in Streptomyces lividans JF - FEBS Open Bio N2 - Amino acid-based surfactants are valuable compounds for cosmetic formulations. The chemical synthesis of acyl-amino acids is conventionally performed by the Schotten-Baumann reaction using fatty acyl chlorides, but aminoacylases have also been investigated for use in biocatalytic synthesis with free fatty acids. Aminoacylases and their properties are diverse; they belong to different peptidase families and show differences in substrate specificity and biocatalytic potential. Bacterial aminoacylases capable of synthesis have been isolated from Burkholderia, Mycolicibacterium, and Streptomyces. Although several proteases and peptidases from S. griseus have been described, no aminoacylases from this species have been identified yet. In this study, we investigated two novel enzymes produced by S. griseus DSM 40236ᵀ . We identified and cloned the respective genes and recombinantly expressed an α-aminoacylase (EC 3.5.1.14), designated SgAA, and an ε-lysine acylase (EC 3.5.1.17), designated SgELA, in S. lividans TK23. The purified aminoacylase SgAA was biochemically characterized, focusing on its hydrolytic activity to determine temperature- and pH optima and stabilities. The aminoacylase could hydrolyze various acetyl-amino acids at the Nα -position with a broad specificity regarding the sidechain. Substrates with longer acyl chains, like lauroyl-amino acids, were hydrolyzed to a lesser extent. Purified aminoacylase SgELA specific for the hydrolysis of Nε -acetyl-L-lysine was unstable and lost its enzymatic activity upon storage for a longer period but could initially be characterized. The pH optimum of SgELA was pH 8.0. While synthesis of acyl-amino acids was not observed with SgELA, SgAA catalyzed the synthesis of lauroyl-methionine. KW - Streptomyces lividans KW - recombinant expression KW - Streptomyces griseus KW - ε-lysine acylase KW - α-aminoacylase Y1 - 2023 U6 - https://doi.org/10.1002/2211-5463.13723 SN - 2211-5463 N1 - Corresponding author: Petra Siegert VL - 13 IS - 12 SP - 2224 EP - 2238 PB - Wiley CY - Hoboken, NJ ER - TY - CHAP A1 - Kurz, Melanie T1 - Waffen und militärische Ausrüstung in Systemspielzeugwelten T2 - Design für Spiel, Spaß, Spannung: Gestaltung von Artefakten zum spielerischen Handeln / herausgegeben von Melanie Kurz und Thilo Schwer Y1 - 2023 SN - 978-3-89986-396-3 SP - 104 EP - 121 PB - avedition CY - Stuttgart ER - TY - JOUR A1 - Herssens, Nolan A1 - Cowburn, James A1 - Albracht, Kirsten A1 - Braunstein, Bjoern A1 - Cazzola, Dario A1 - Colyer, Steffi A1 - Minetti, Alberto E. A1 - Pavei, Gaspare A1 - Rittweger, Jörn A1 - Weber, Tobias A1 - Green, David A. ED - Cattaneo, Luigi T1 - Movement in low gravity environments (MoLo) programme – the MoLo-L.O.O.P. study protocol JF - PLOS ONE / Public Library of Science N2 - Exposure to prolonged periods in microgravity is associated with deconditioning of the musculoskeletal system due to chronic changes in mechanical stimulation. Given astronauts will operate on the Lunar surface for extended periods of time, it is critical to quantify both external (e.g., ground reaction forces) and internal (e.g., joint reaction forces) loads of relevant movements performed during Lunar missions. Such knowledge is key to predict musculoskeletal deconditioning and determine appropriate exercise countermeasures associated with extended exposure to hypogravity. Y1 - 2022 U6 - https://doi.org/10.1371/journal.pone.0278051 SN - 1932-6203 VL - 17 IS - 11 PB - Plos CY - San Francisco ER - TY - THES A1 - Stercken, Maike T1 - Social Media - Segen oder Fluch? : Eine Aufklärungskampagne zu Auswirkungen von Social Media Nutzung N2 - Das Projekt „Social Media – Segen oder Fluch“ beschäftigt sich mit negativen Auswirkungen, die die Nutzung Sozialer Medien haben kann. Soziale Medien werden heutzutage ständig und von fast jedem genutzt, vor allem von Jugendlichen und jungen Erwachsenen. Vielen ist aber nicht bewusst, dass sich die Nutzung negativ auf sie und ihre Gesundheit auswirken kann. Eine Kampagne soll daran etwas ändern. Soziale Medien bzw. der Content, der die Nutzer:innen negativ beeinflusst, ist wie ein Monster, vor dem sich die Nutzer:innen in acht nehmen müssen. Angesprochen werden hauptsächlich 12-29-jährige, die Soziale Medien nutzen. Die Kampagne soll durch verschiedene Maßnahmen wie Plakatwerbung und Posts auf Social Media Kanälen, den negativen Auswirkungen von Social Media Nutzung entgegenwirken. Sie soll über die Auswirkungen aufklären und zu einem bewussteren Umgang mit Sozialen Netzwerken anregen. KW - Soziale Medien KW - Monster KW - Gefahr KW - Depressionen KW - Kampagne Y1 - 2023 PB - FH Aachen CY - Aachen ER - TY - GEN T1 - Ordnung zur Änderung der Prüfungsordnung für den Masterstudiengang Architektur im Fachbereich Architektur an der Fachhochschule Aachen N2 - Aufgrund des § 2 Absatz 4 Satz 1 in Verbindung mit § 64 des Gesetzes über die Hochschulen des Landes Nordrhein-Westfalen (Hochschulgesetz – HG) vom 16. September 2014 (GV. NRW. S. 547), zuletzt geändert durch Artikel 3 des Gesetzes vom 17. Oktober 2017 (GV. NRW. S. 806), und der Rahmenprüfungsordnung (RPO) für die Bachelor- und Masterstudiengänge an der Fachhochschule Aachen vom 1. Februar 2018 (FH-Mitteilung Nr. 3/2018) hat der Fachbereich Architektur folgende Änderung der Prüfungsordnung vom 5. Juli 2018 (FH-Mitteilung Nr. 105/2018) erlassen. T3 - FH-Mitteilungen - 67/2019 KW - Amtliche Mitteilung KW - Master Architektur KW - Prüfungsordnung Y1 - 2019 ER - TY - GEN T1 - Prüfungsordnung für die Bachelorstudiengänge „Biotechnologie“ und „Biotechnologie mit Praxis- oder Auslandssemester“ im Fachbereich Chemie und Biotechnologie an der FH Aachen BT - vom 2. Mai 2023 – FH-Mitteilung Nr. 37/2023 in der Fassung der Bekanntmachung der Änderungsordnung vom 3. Juli 2023 – FH-Mitteilung Nr. 55/2023 (Nichtamtliche lesbare Fassung) N2 - § 1 | Geltungsbereich der Prüfungsordnung § 2 | Ziel des Studiums, Zweck der Prüfung, Abschlussgrad § 3 | Beginn, Dauer, Umfang und Gliederung des Studiums § 4 | Zugang zum Studium, Praktikum § 5 | Prüfungsausschuss § 6 | Studien- und Prüfungselemente § 7 | Zulassung zu den Prüfungen § 8 | Durchführung von Prüfungen § 9 | Verbesserungsversuch § 10 | Anrechnung von Studienzeiten, Studien- und Prüfungsleistungen § 11 | Praxissemester § 12 | Mobilitätssemester (Auslandssemester) § 13 | Bachelorprojekt§ 14 | Gesamtnote, Zeugnis, Bachelorurkunde § 15 | Inkrafttreten, Veröffentlichung Anlage 1 | Studienplan Kernstudium Anlage 2 | Allgemeine Kompetenzen T3 - FH-Mitteilungen - 56/2023 KW - Amtliche Mitteilungen KW - Prüfungsordnung KW - Bachelor Y1 - 2023 CY - Aachen ER - TY - GEN T1 - Prüfungsordnung für den Bachelorstudiengang Architektur im Fachbereich Architektur an der Fachhochschule Aachen BT - vom 5. Juli 2018 – FH-Mitteilung Nr. 104/2018 in der Fassung der Bekanntmachung der Änderungsordnung vom 17. Juli 2019 – FH-Mitteilung Nr. 66/2019 (nichtamtliche lesbare Fassung | Studienbeginn ab WS 2019/20) T3 - FH-Mitteilungen - 68/2019 KW - Amtliche Mitteilungen KW - Bachelor KW - Prüfungsordnung Y1 - 2019 ER - TY - THES A1 - Schmitz, Marvin T1 - Eishockey Uni-Cup der RWTH Aachen : Produktion einer Sportübertragung N2 - Der Uni-Cup ist ein Amateur Eishockey Turnier der RWTH Aachen. Es treten Studierende und Professor:innen gegeneinander an. Ausgetragen wurde das Turnier vor etwa 2.500 Zuschauern in der 100,5 Arena am Tivoli. Um das Event einer breiteren Masse zugänglich zu machen, wurde dort im Rahmen der Bachelorarbeit erstmals eine Live Übertragung produziert. Das Ziel dabei war es, eine möglichst professionelle und unterhaltsame Show zu kreieren. KW - Livestream KW - Eishockey KW - Sport KW - RWTH Aachen KW - Regie Y1 - 2023 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER - TY - THES A1 - Thiele, Jana T1 - Düsseldorfer Schauspielhaus : „Entwicklung eines neuen Erscheinungsbildes“ N2 - In der heutigen digitalisierten und individualisierten Welt spielt das Theater weiterhin eine bedeutende Rolle als kulturelle Institution und als Ort des künstlerischen Ausdrucks. Dabei ist einer der wichtigsten Aspekte die Bewegung. Sie findet auf der Bühne in jeglicher Form statt – Tanz, Gestik, Mimik, die Schritte der Schauspieler:innen, Sprünge, Armbewegungen. All diese unterschiedlichen Arten von Bewegung sind ausschlaggebend für die Wirkung der Texte und Stücke. Für das neue Erscheinungsbild des Düsseldorfer Schauspielhauses wurde dieser Bewegungsaspekt in ein spannendes, modernes und übersichtliches Corporate Design übersetzt. Das Ergebnis: Sonderzeichen, die „Bewegung“ aufgreifen und entsprechend „verformt“ wurden. Durch ihr verändertes Aussehen spiegeln sie diese Bewegung abstrahiert wider und führen abwechslungsreich durch die verschiedenen Medien. KW - Schauspiel KW - Theater KW - Bewegung KW - Sonderzeichen KW - Schauspielhaus Y1 - 2023 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER - TY - THES A1 - Thiem, Antonia T1 - Entwicklung eines neuen Corporate Design für ein Museum mit dem Schwerpunkt Lichtkunst N2 - Weithin leuchtend – tief unter der Erde strahlend: Das »Zentrum für internationale Lichtkunst« in Unna ist ein »Unikat« unter den Kunstmuseen weltweit, da das Museum das Einzige ist, welches sich ausschließlich der zeitgenössischen Lichtkunst widmet. Seit 2001 erstreckt sich die Sammlung von 21 dauerhaften Werken in einem großzügigen Kellergewölbe. Viele der Lichtinstallationen wurden eigens für die Räumlichkeiten konzipiert und sind sowohl in ihrem technischen, als auch ästhetischen und perspektivischen Auftritt unverwechselbar. Die Zielsetzung des Projektes ist es, ein systematisches und einheitliches Erscheinungsbild, welches crossmedial eingesetzt werden kann, zu erarbeiten. Des Weiteren soll die Thematik Lichtkunst in dem Corporate Design aufgegriffen und widergespiegelt werden, sodass die Berührungspunkte des Publikums spannungsvoll und einprägend aufgenommen werden. KW - Lichtkunst KW - Kunst KW - Corporate Design KW - Museum KW - Lichtkunst Museum Y1 - 2023 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER - TY - THES A1 - Thoennißen, Amber Katharina T1 - Boys will be boys N2 - "boys will be boys" erkundet bestehende Meinungen zum Thema Männlichkeit und versucht Alternativen zu finden: Wege, die Männlichkeit gehen und Richtungen, in die sich Männlichkeit verändern kann. Auf 236 Seiten wird das Thema von so vielen Seiten wie irgendwie möglich beleuchtet. Es gibt sowohl sehr persönliche, subjektive Beschäftigung mit dem Thema als auch eine objektive, wissenschaftliche Herangehensweise. Das Buch ist vor allem mit typografischen Elementen gestaltet worden, wobei in Inhalt und Typografie viel Wert auf Niedrigschwelligkeit gelegt wurde. Außen ist ein partieller Relieflack aufgetragen worden, innen hat das Buch bedrucktes Vorsatzpapier. Ziel des Projektes war es, Männlichkeit und die verschiedenen Meinungen dazu möglichst verständlich wiedergeben zu können, um so einen Dialog zum Thema anzuregen. KW - Männlichkeit KW - Editorial KW - Typografie KW - Gesellschaftskritik KW - Diskurs Y1 - 2023 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER - TY - THES A1 - Stiphout, Maret van T1 - Entwicklung eines neuen Erscheinungsbildes für das Wallraf-Richartz-Museum und Fondation Carboud N2 - Das Wallraf-Richartz-Museum & Fondation Corboud besitzt eine der wichtigsten europäischen Kunstsammlungen vom Mittelalter bis zum 19. Jahrhundert. Durch das Zusammenspiel von Forschung und Vermittlung der Kunst- und Epochengeschichte trägt das Museum maßgeblich zum Erhalt des kulturellen Erbes und dem Meinungsaustausch über die Vergangenheit, Gegenwart und die Zukunft bei. Im Fokus des neuen Erscheinungsbildes steht die an den kulturellen und historischen Kontext angepasste Szenografie des Museums. Die beeindruckend verzierten Bilderrahmen der gezeigten Kunstepochen werden abstrahiert und durch einen typografischen Rahmen neu interpretiert. Das entwickelte Headline-Prinzip wird durch eine sehr zurückhaltende Gestaltung ergänzt, was der Thematik und den gezeigten Meisterwerken Raum zum Wirken verleiht. KW - Corporatedesign KW - Wallrafmuseum KW - Neugestaltung KW - Mittelalter KW - Barock Y1 - 2023 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER - TY - THES A1 - Transfeld, Janine T1 - Ein Kl-gestütztes Software-Tool : zur Unterstützung der Projektgestaltung der BMW AG N2 - Die Bachelorarbeit beschäftigte sich mit der Integration von künstlicher Intelligenz (KI) in softwarebasierte Lösungen und hatte das Ziel, ein prototypisches Lösungsmodell zu entwickeln. Dabei wurde das User-Experience-Designverfahren angewendet, um eine neue innovative Arbeitsweise zu schaffen, die KI-gestützte Produktentwicklungsprozesse umfasst. KW - Kooperation KW - FH Aachen KW - BMW KW - Künstliche Intelligenz KW - Neue Arbeitsweise Y1 - 2023 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER - TY - THES A1 - Vaut, Ina T1 - Hippocampus N2 - Hippocampus – Eine Publikation über das Erscheinungsbild und Verhaltensweisen von Seepferdchen, ihre Lebensräume, Bedrohungen und die Schutzmaßnahmen. Seepferdchen gehören zu den wenigen Fischarten, die allgemein bekannt sind. In den meisten Fällen werden Seepferdchen einfach als »süß« beschrieben. Doch Seepferdchen haben weit mehr zu bieten als ihr märchenhaftes Aussehen. Diese Publikation setzt sich mit kuriosen Erkenntnissen, aktuellen Forschungsergebnissen und Mythen rund um Seepferdchen auseinander und dient als Einstieg in die Thematik. KW - Editorail Design KW - Publikation KW - Seepferdchen KW - Habitate KW - Spezies Y1 - 2023 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER - TY - CHAP A1 - Heimes, Heiner Hans A1 - Kampker, Achim A1 - Dorn, Benjamin A1 - Kehrer, Mario A1 - Dünnwald, Simon A1 - Badura, Dennis A1 - Terren, Maximilian A1 - Röth, Thilo ED - Kampker, Achim ED - Heimes, Heiner Hans T1 - Produktionsprozesse der Fahrzeugstruktur T2 - Elektromobilität: Grundlagen einer Fortschrittstechnologie Y1 - 2023 SN - 978-3-662-65811-6 (Print) SN - 978-3-662-65812-3 (Online) U6 - https://doi.org/10.1007/978-3-662-65812-3_13 N1 - Corresponding author: Benjamin Dorn SP - 227 EP - 247 PB - Springer Vieweg CY - Berlin ER - TY - CHAP A1 - Heimes, Heiner Hans A1 - Kampker, Achim A1 - Kehrer, Mario A1 - Dünnwald, Simon A1 - Heetfeld, Lennart A1 - Polzenberg, Jens A1 - Budde, Lucas A1 - Keusen, Maximilian A1 - Pandey, Rahul A1 - Röth, Thilo ED - Kampker, Achim ED - Heimes, Heiner Hans T1 - Fahrzeugstruktur T2 - Elektromobilität: Grundlagen einer Fortschrittstechnologie N2 - Um sowohl Treibhausgas-Emissionen zu verringern als auch Kraftstoffressourcen zu schonen, wird zunehmend an einer Transformation konventionell angetriebener Kraftfahrzeuge hin zu elektrifizierten Antriebskonzepten gearbeitet. Basierend auf herkömmlichen Fahrzeugen mit Verbrennungsmotor wurde eine Vielzahl neuer Antriebssysteme mit verschiedenem Elektrifizierungsgrad entwickelt. Mitte der 1990er-Jahre kamen erste Fahrzeuge mit einem Hybridantrieb auf den Markt. Die Kombination aus Verbrennungs- und Elektromotor erlaubt eine Verbrauchsreduktion und Bremsenergierückgewinnung sowie lokal emissionsfreies Fahren. Y1 - 2023 SN - 978-3-662-65811-6 (Print) SN - 978-3-662-65812-3 (Online) U6 - https://doi.org/10.1007/978-3-662-65812-3_5 N1 - Corresponding author: Heiner Hans Heimes SP - 69 EP - 106 PB - Springer Vieweg CY - Berlin ER - TY - JOUR A1 - Kowalewski, Paul A1 - Bragard, Michael A1 - Hüning, Felix A1 - De Doncker, Rik W. T1 - An inexpensive Wiegand-sensor-based rotary encoder without rotating magnets for use in electrical drives JF - IEEE Transactions on Instrumentation and Measurement N2 - This paper introduces an inexpensive Wiegand-sensor-based rotary encoder that avoids rotating magnets and is suitable for electrical-drive applications. So far, Wiegand-sensor-based encoders usually include a magnetic pole wheel with rotating permanent magnets. These encoders combine the disadvantages of an increased magnet demand and a limited maximal speed due to the centripetal force acting on the rotating magnets. The proposed approach reduces the total demand of permanent magnets drastically. Moreover, the rotating part is manufacturable from a single piece of steel, which makes it very robust and cheap. This work presents the theoretical operating principle of the proposed approach and validates its benefits on a hardware prototype. The presented proof-of-concept prototype achieves a mechanical resolution of 4.5 ° by using only 4 permanent magnets, 2Wiegand sensors and a rotating steel gear wheel with 20 teeth. KW - Rotary encoder KW - Wiegand sensor Y1 - 2023 U6 - https://doi.org/10.1109/TIM.2023.3326166 SN - 0018-9456 (Print) SN - 1557-9662 (Online) N1 - Early Access SP - 10 Seiten PB - IEEE ER - TY - CHAP A1 - Groß, Rolf Fritz A1 - Müller, D. A1 - Herting, D. A1 - Schneemann, A. A1 - Renz, Ulrich ED - Rahman, Jamal ED - Jaschinski, Hans T1 - Modulare Messdatenerfassung in Forschung und Lehre T2 - Virtuelle Instrumente in der Praxis : Begleitband zum Kongress VIP '97 N2 - The Lehrstuhl für Wärmeübertragung und Klimatechnik at the Aachen University of Technology operates several test facilities to investigate fundamentals of heat and mass transfer supported by the Deutsche Forschungsgemeinschaft, the Minister für Forschung und Technologie and the industry. In order to get high-resolution and reproselection of hardware components is as critical as the design of software routines to perform successful and accurate measurements. In the following the development of the measurement and control system for three different test facilities is presented and discussed. Special attention is given to the education of students within the framework of laboratories and scientific experiments. Y1 - 1997 SN - 978-3-7785-2667-5 Pp. SP - 282 EP - 288 PB - Hüthig CY - Heidelberg ER - TY - GEN T1 - Ordnung zur Änderung der Prüfungsordnung für den Bachelorstudiengang Architektur im Fachbereich Architektur an der Fachhochschule Aachen N2 - Aufgrund des § 2 Absatz 4 Satz 1 in Verbindung mit § 64 des Gesetzes über die Hochschulen des Landes Nordrhein-Westfalen (Hochschulgesetz – HG) vom 16. September 2014 (GV. NRW. S. 547), zuletzt geändert durch Artikel 3 des Gesetzes vom 17. Oktober 2017 (GV. NRW. S. 806), und der Rahmenprüfungsordnung (RPO) für die Bachelor- und Masterstudiengänge an der Fachhochschule Aachen vom 1. Februar 2018 (FH-Mitteilung Nr. 3/2018) hat der Fachbereich Architektur folgende Änderung der Prüfungsordnung vom 5. Juli 2018 (FH-Mitteilung Nr. 104/2018) erlassen. T3 - FH-Mitteilungen - 66/2019 KW - Prüfungsordnung KW - Bachelor KW - Amtliche Mitteilungen Y1 - 2019 CY - Aachen ER - TY - CHAP A1 - Dautzenberg, H. A1 - Groß, Rolf Fritz A1 - Renz, Ulrich ED - Jamal, Rahman T1 - Meßtechnik auf dem Prüfstand: Forschung zur Heißgasfiltration T2 - Virtuelle Instrumente in der Praxis. Begleitband zum Kongress VIP 1996 N2 - Im Rahmen von Forschungsvorhaben des BMBF und verschiedener Industriepartner betreibt der Lehrstuhl für Wärmeübertragung und Klimatechnik der RWTH Aachen Pilotanlagen und Prüfstände für Untersuchungen auf dem Gebiet der Heißgasfiltration mit keramischen Filterelementen. Als wesentlicher Garant für den Erfolg der Forschungsarbeit muß die auf das jeweilige Projekt genau abgestimmte Meß- und Regelungstechnik angesehen werden. Hierbei zählt neben der Auswahl geeigneter Hardwarekomponenten auch die Softwareentwicklung unter einer leistungsstarken und zuverlässigen Programmierumgebung. Anhand des Aufbaus dreier Versuchsanlagen im Technikumsmaßstab soll das Anforderungsprofil an die Meßtechnik bis hin zur Umsetzung innerhalb der Anlage skizziert werden. Der Heißgasfiltrationsprüfstand im Heizkraftwerk der RWTH Aachen dient der Beobachtung des Reinigungsverhaltens keramischer Filterelemente bei der Heißgasentstaubung im Temperaturbereich bis 850 Grad C. Wesentlich für die Meßwerterfassung ist hierbei die Kopplung eines Orion-Datenloggers der Firma Schlumberger mit LabView 4.0. Im Hochtemperaturofen des Lehrstuhls werden instationäre Druckmessungen an einer keramischen Filterkerze während eines Abreinigungsimpulses bei 950 Grad C mit hoher Samplingrate durchgeführt. Hierbei übernimmt eine durch LabView 4.0 angesteuerte E-Series Karte der Firma National Instruments die Signalaufnahme. Die katalytische Schadstoffreduktion und Entstaubung heißer Rauchgase bei 900 Grad C sind Ziele der Untersuchungen in einer erstellten Versuchsanlage mit einem Quarzglasreaktor. Die Signalerfassung und -konditionierung erfolgt über SCXI in Verbindung mit LabView 4.0, die Steuerung der Anlage übernehmen zwei Multifunktionskarten (National Instruments). KW - keramischer Werkstoff KW - Filter (Stofftrennung) KW - Filtration KW - Entstaubung KW - Staubfilter Y1 - 1996 N1 - 5.-6. November 1996 Forum der Technik München, Germany SP - 202 EP - 208 PB - National Instruments Germany CY - München ER - TY - JOUR A1 - Adels, Klaudia A1 - Elbers, Gereon A1 - Diehl, Bernd A1 - Monakhova, Yulia T1 - Multicomponent analysis of dietary supplements containing glucosamine and chondroitin: comparative low- and high-field NMR spectroscopic study JF - Analytical Sciences N2 - With the prevalence of glucosamine- and chondroitin-containing dietary supplements for people with osteoarthritis in the marketplace, it is important to have an accurate and reproducible analytical method for the quantitation of these compounds in finished products. NMR spectroscopic method based both on low- (80 MHz) and high- (500–600 MHz) field NMR instrumentation was established, compared and validated for the determination of chondroitin sulfate and glucosamine in dietary supplements. The proposed method was applied for analysis of 20 different dietary supplements. In the majority of cases, quantification results obtained on the low-field NMR spectrometer are similar to those obtained with high-field 500–600 MHz NMR devices. Validation results in terms of accuracy, precision, reproducibility, limit of detection and recovery demonstrated that the developed method is fit for purpose for the marketed products. The NMR method was extended to the analysis of methylsulfonylmethane, adulterant maltodextrin, acetate and inorganic ions. Low-field NMR can be a quicker and cheaper alternative to more expensive high-field NMR measurements for quality control of the investigated dietary supplements. High-field NMR instrumentation can be more favorable for samples with complex composition due to better resolution, simultaneously giving the possibility of analysis of inorganic species such as potassium and chloride. KW - Glucosamine KW - Chondroitin sulfate KW - Polysaccharides KW - Dietary supplements KW - High-field NMR Y1 - 2023 U6 - https://doi.org/10.1007/s44211-023-00433-2 SN - 1348-2246 (Online) SN - 0910-6340 (Print) N1 - Corresponding author: Yulia Monakhova VL - 2023 PB - Springer Verlag CY - Cham ER - TY - RPRT A1 - Christ, Ansgar A1 - Groß, Rolf Fritz A1 - Renz, Ulrich T1 - Strömungs-, Filterkuchen- und Abreinigungsmodelle für Heißgasfilter, Teilvorhaben "Numerische Simulation des Abreinigungsvorganges und der Rohgasströmung" KW - Prozesssimulation KW - Filterkuchen KW - Druckvergasung KW - Druckwirbelschichtfeuerung KW - Rauchgasreinigung Y1 - 1998 U6 - https://doi.org/10.2314/GBV:50431601X N1 - Verbundprojekt im Rahmen der Projektträgerschaft BEO des BMBF der Partner RWTH Aachen, Lehrstuhl für Wärmeübertragung und Klimatechnik Brandenburgische Technische Universität Cottbus, Lehrstuhl Regelungstechnik Universität Karlsruhe, Institut für Mechanische Verfahrenstechnik und Mechanik LLB Lurgi Lentjes Babcock Energietechnik GmbH, Oberhausen Förderkennzeichen: 0326831B Abschlußbericht ER - TY - BOOK A1 - Kurz, Melanie A1 - Schwer, Thilo T1 - Design für Spiel, Spaß, Spannung: Gestaltung von Artefakten zum spielerischen Handeln / herausgegeben von Melanie Kurz und Thilo Schwer T3 - Schriften / Gesellschaft für Designgeschichte N2 - Die kulturgeschichtlichen Stationen des Spielens vom Beginn der Industrialisierung bis zur Jahrtausendwende werden sowohl aus dem Blickwinkel der Designgeschichte als auch aus dem der Game Studies betrachtet. Die Bandbreite der Themen reicht von der Bauhaus-Wurfpuppe bis zur Barbie, vom Japonismus bis zur Pixelgrafik, von der grafischen Raumillusion zu 3D-Umgebungen und Interaktionsgestaltung, vom Brettspiel bis zum Kriegsspielzeug, von den Utopien der beginnenden Neuzeit bis zu merkantilen Absichten digitaler Spielkonzepte. Y1 - 2023 SN - 978-3-89986-396-3 N1 - Band 6 PB - avedition CY - Stuttgart ET - 1. Auflage ER - TY - BOOK A1 - Janser, Frank A1 - Havermann, Marc A1 - Hoeveler, Bastian A1 - Hertz, Cyril A1 - Bergmann, Ole T1 - Strömungslehre und Aerodynamik : inkompressible Profile und Tragflügelaerodynamik, Band 2 N2 - Das vorliegende Buch dient als Grundlage für die Bachelor- und Master-Ausbildung von Studierenden im Fachgebiet Strömungslehre und Aerodynamik. Im hier behandelten Teilbereich der inkompressiblen Profile und Tragflügelaerodynamik werden schwerpunktmäßig die folgenden Themen besprochen: - Profilaerodynamik - Tragflügelaerodynamik - Flugzeugpolare - Methoden zur Flugbereichserweiterung - Schwebeschub und Schwebeleistung - Propellerblattaerodynamik - Numerische Methoden zur Tragflügelberechnung Y1 - 2023 SN - 978-3-8107-0261-6 PB - Mainz CY - Aachen ET - 4. Auflage ER - TY - CHAP A1 - Freyer, Nils A1 - Kempt, Hendrik ED - Bhakuni, Himani ED - Miotto, Lucas T1 - AI-DSS in healthcare and their power over health-insecure collectives T2 - Justice in global health N2 - AI-based systems are nearing ubiquity not only in everyday low-stakes activities but also in medical procedures. To protect patients and physicians alike, explainability requirements have been proposed for the operation of AI-based decision support systems (AI-DSS), which adds hurdles to the productive use of AI in clinical contexts. This raises two questions: Who decides these requirements? And how should access to AI-DSS be provided to communities that reject these standards (particularly when such communities are expert-scarce)? This chapter investigates a dilemma that emerges from the implementation of global AI governance. While rejecting global AI governance limits the ability to help communities in need, global AI governance risks undermining and subjecting health-insecure communities to the force of the neo-colonial world order. For this, this chapter first surveys the current landscape of AI governance and introduces the approach of relational egalitarianism as key to (global health) justice. To discuss the two horns of the referred dilemma, the core power imbalances faced by health-insecure collectives (HICs) are examined. The chapter argues that only strong demands of a dual strategy towards health-secure collectives can both remedy the immediate needs of HICs and enable them to become healthcare independent. Y1 - 2023 SN - 9781003399933 U6 - https://doi.org/10.4324/9781003399933-4 SP - 38 EP - 55 PB - Routledge CY - London ER - TY - RPRT A1 - Christ, Ansgar A1 - Groß, Rolf Fritz A1 - Renz, Ulrich T1 - HGR: Untersuchung zur Minimierung von gasförmigen Schadstoffen aus Rauchgasen bei der Heißgasfiltration T1 - Hot gas filtration: investigations to remove gaseous pollutant components out of flue gas during hot gas filtration N2 - Gas- und Dampfturbinen-Kraftwerke mit Druckwirbelschicht- oder mit Druckvergasungsverfahren ermöglichen die Verstromung von Kohle mit hohem Wirkungsgrad und niedrigen Emissionen. Eine Voraussetzung für den Betrieb dieser Anlagen ist die Entstaubung der Rauchgase bei hohen Temperaturen und Drücken. Abreinigungsfilter mit keramischen Elementen werden dazu eingesetzt. Eine Reduzierung gasförmiger Schadstoffe unter den gleichen Bedingungen könnte Rauchgaswäsche ersetzen. Ziel des Gesamtvorhabens ist es, die Integration von Heißgasfiltration und katalytischem Abbau der Schadstoffe Kohlenmonoxid, Kohlenwasserstoffe und Stickoxide in einen Verfahrensschritt zu untersuchen. Die Arbeitsschwerpunkte dieses Teilvorhabens betreffen: die katalytische Wirkung eisenhaltiger Braunkohlenaschen, die Wirksamkeit des Calciumaluminat als Katalysator des Abbaus unverbrannter Kohlenwasserstoffe im Heißgasfilter, numerische Simulation der kombinierten Abscheidung von Partikeln und gasförmigen Schadstoffen aus Rauchgasen N2 - Power plants with gas and steam turbines in pressurized fluidized bed or pressurized gasification processes enable power generation of coal with high efficiancy and little emissions. To run these plants the cleaning of the flue gas is necessary before entering the turbines under the conditions of high temperature and pressure. Ceramic filter elements are the most probable method for hot gas cleaning. A simultaneous reduction of gaseous pollutant components under these conditions could help to make the whole process more efficiant. The aim of the project is to integrate the catalytic reduction of carbon monoxide, hydrocarbons and nitric oxides into the hot gas filtration with ceramic filter elements as a one step mecanism. The project is focused on: the catalytic behaviour of ferrugious ashes of brown coal, the effectiveness of calcinated aluminates as a catalyst to remove uncombuste hydrocarbons in a hot gas filtration unit, numerical simulation of the combined removal of particels and gaseous pollutant components out of the flue gas. KW - Kraftwerkstechnik KW - Stickstoffoxide KW - Kohlenmonoxidbelastung KW - Schadgas KW - Heterogene Katalyse Y1 - 1998 U6 - https://doi.org/10.2314/GBV:504318411 N1 - Verbundprojekt im Rahmen der Projektträgerschaft BEO des BMBF der Partner RWTH Aachen, Lehrstuhl für Wärmeübertragung und Klimatechnik uve Institut für Technische Chemie und Umweltschutz GmbH, Berlin-Adlershof Hugo Petersen, Gesellschaft für verfahrenstechnischen Anlagenbau mbH&Co.KG, Wiesbaden Förderkennzeichen: 0326819F [Abschlußdatum des Vorhabens: Dezember 1997] ER - TY - CHAP A1 - Thulfaut, Christian A1 - Groß, Rolf Fritz A1 - Renz, Ulrich ED - Jamal, Rahman ED - Jaschinski, Hans T1 - Messwerterfassung und –auswertung mit LabView: Experimentelle Analyse der Mischungsgüte in Hybridzellenkühltürmen T2 - Virtuelle Instrumente in der Praxis. Begleitband zum Kongress VIP 2000 N2 - Zur Kühlung von Abwärmeströmen aus Kraftwerksprozessen werden in zunehmenden Maße Hybridzellenkühltürme mit Zwangskonvektion eingesetzt, deren wesentlicher Vorteil ihre geringe Bauhöhe ist. Um bei derartigen Kühltürmen eine Sichtbehinderung oder Glatteisgefährdung durch bodennahen Nebel zu vermeiden, muss durch eine optimale Vermischung des Trocken- und Naßluftanteils gewährleistet sein, daß aus der Kühlturmkrone keine Nebelschwaden austreten. In Zusammenarbeit mit der Industrie betreibt der Lehrstuhl für Wärmeübertragung und Klimatechnik der RWTH Aachen einen Versuchsstand zur Erfassung der Mischungsgüte in Hybridzellenkühltürmen. In maßstabsgerechter Nachbildung können dabei am Modell alle relevanten Einflußgrößen wie Kühlturmgeometrie, Gestaltung zusätzlicher Mischeinbauten sowie die Betriebsparameter variiert werden. Mit Hilfe einer unter LabView 5.01 erstellten Software werden sowohl die l3etriebszustüncle online überwacht, als auch die benötigten Meßwerte zur Bestimmung der Mischungsgüte erfaßt. Über die grafische Oberfläche können sämtliche Meßoptionen gesteuert sowie alle Meßdaten visualisiert und kontrolliert werden. In das LabView-Programm sind darüber hinaus Routinen zur Auswertung der Daten implementiert worden, die sowohl eine direkte Darstellung der Ergebnisse in Form von Diagrammen ermöglichen, als auch zur Weiterverarbeitung einen Datenexport in eine Microsoft- Excel-Tabelle vorsehen. N2 - The Institute of Heat Transfer and Air Conditioning at the Aachen University of Technology operates in co-operation with industrial partners a test facility in order to investigate mixture quality in hybrid cooling towers. In a scaled mock-up a variation of all relevant data such as the geometry of the cooling tower, the design of additional mixers and the operation parameters could be realized. A software tool, created with LabView 5.01, offers the possibility to control the whole process and to measure all relevant quantities. The graphic user interface permits an online control and a visualization of the measured values. Beyond this the program is not only able to evaluate the data and to represent the results in form of diagrams, but also to export the data directly into an Microsoft-Excel-sheet for further analysing. Y1 - 2000 SN - 3-7785-2789-4 (print) SP - 54 EP - 60 PB - Hüthig CY - Heidelberg ER - TY - CHAP A1 - Tischbein, Franziska A1 - Kean, Kilian A1 - Vertgewall, Chris Martin A1 - Ulbig, Andreas A1 - Altherr, Lena T1 - Determination of the topology of low-voltage distribution grids using cluster methods T2 - 27th International Conference on Electricity Distribution (CIRED 2023) N2 - Due to the decarbonization of the energy sector, the electric distribution grids are undergoing a major transformation, which is expected to increase the load on the operating resources due to new electrical loads and distributed energy resources. Therefore, grid operators need to gradually move to active grid management in order to ensure safe and reliable grid operation. However, this requires knowledge of key grid variables, such as node voltages, which is why the mass integration of measurement technology (smart meters) is necessary. Another problem is the fact that a large part of the topology of the distribution grids is not sufficiently digitized and models are partly faulty, which means that active grid operation management today has to be carried out largely blindly. It is therefore part of current research to develop methods for determining unknown grid topologies based on measurement data. In this paper, different clustering algorithms are presented and their performance of topology detection of low voltage grids is compared. Furthermore, the influence of measurement uncertainties is investigated in the form of a sensitivity analysis. Y1 - 2023 SN - 978-1-83953-855-1 U6 - https://doi.org/10.1049/icp.2023.0478 N1 - 27th International Conference on Electricity Distribution (CIRED 2023), 12-15 June 2023, Rome, Italy. SP - 1 EP - 5 PB - IEEE ER - TY - CHAP A1 - Eichenbaum, Julian A1 - Nikolovski, Gjorgji A1 - Mülhens, Leon A1 - Reke, Michael A1 - Ferrein, Alexander A1 - Scholl, Ingrid T1 - Towards a lifelong mapping approach using Lanelet 2 for autonomous open-pit mine operations T2 - 2023 IEEE 19th International Conference on Automation Science and Engineering (CASE) N2 - Autonomous agents require rich environment models for fulfilling their missions. High-definition maps are a well-established map format which allows for representing semantic information besides the usual geometric information of the environment. These are, for instance, road shapes, road markings, traffic signs or barriers. The geometric resolution of HD maps can be as precise as of centimetre level. In this paper, we report on our approach of using HD maps as a map representation for autonomous load-haul-dump vehicles in open-pit mining operations. As the mine undergoes constant change, we also need to constantly update the map. Therefore, we follow a lifelong mapping approach for updating the HD maps based on camera-based object detection and GPS data. We show our mapping algorithm based on the Lanelet 2 map format and show our integration with the navigation stack of the Robot Operating System. We present experimental results on our lifelong mapping approach from a real open-pit mine. Y1 - 2023 SN - 979-8-3503-2069-5 (Online) SN - 979-8-3503-2070-1 (Print) U6 - https://doi.org/10.1109/CASE56687.2023.10260526 N1 - 19th International Conference on Automation Science and Engineering (CASE), 26-30 August 2023, Auckland, New Zealand. PB - IEEE ER - TY - BOOK A1 - Heuermann, Holger T1 - Mikrowellentechnik : Feldsimulation, nichtlineare Schaltungstechnik, Komponenten und Subsysteme, Plasmatechnik, Antennen und Ausbreitung N2 - Das Lehrbuch behandelt alle Aspekte, die den aktuellen Stand der GHz-Technik betreffen. Das Buch behandelt die verschiedenen numerischen Feldsimulationsverfahren. Mit vielen modernen Themen. KW - Elektrotechnik KW - Hochfrequenztechnik KW - Feldsimulation KW - Plasmatechnik KW - Antennen Y1 - 2023 SN - 978-3-658-41286-9 U6 - https://doi.org/10.1007/978-3-658-41287-6 PB - Springer Vieweg CY - Wiesbaden ET - 2. Auflage ER - TY - THES A1 - Namakiravesh, Ehsan T1 - Coupé Nr. 13 N2 - Coupé Nr. 13 ist eine kurze Animation über ein Zugcoupé mit 6 individuellen Passagieren und den 5 Stufen der Kommunikationsentwicklung zwischen ihnen. Die Passagiere des "Coupé Nummer 13" werden zu ihrem wahren Ich, wenn sie sich gegenseitig die Kofferklappen öffnen. Doch dieses Offen-Sein ist gar nicht so einfach. Es fühlt sich anfangs verletzlich an, psychologisch nackt und meist ängstlich. Aber diese Verletzlichkeit ist aus psychologischer Sicht der Schlüssel zu engen Beziehungen. Wahre Verbundenheit entsteht nur, wenn man den Weg zur Schattenseite des anderen findet – indem man sie so sieht und annimmt, wie sie wirklich sind. In der Tat bewundern und respektieren wir meistens die Verletzlichkeit anderer Menschen. Wir sehen sie in der Regel als ein Zeichen von Stärke und Mut – nicht von Schwäche. KW - Animation KW - Kommunikation KW - Zug KW - Schattenseite KW - Schein Y1 - 2023 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER - TY - THES A1 - Scheffel, Zeno Samuel T1 - Identität, Zusammenhalt, Zugehörigkeit : Die Exploration der Gestaltung von Fußballtrikots N2 - Das Fußballtrikot – Arbeitsbekleidung, Identifikationsmerkmal, Distinktionsmerkmal? Was ist das Fußballtrikot, was sind seine identitätsstiftenden Merkmale und welche Gestaltungsparameter prägen sein heutiges Aussehen? In dieser Publikation wird die Geschichte des Trikots ebenso wie die äußeren Einflüsse auf sein heutiges Erscheinungsbild dokumentiert und analysiert. Die Publikation definiert die verschiedenen Gestaltungsparameter, erläutert diese und ordnet sie ein. Ebenso wird ein Einblick in den kreativen Gestaltungsprozess von Fußballtrikots gewährt. Das Ziel dieser Publikation besteht darin, das Erscheinungsbild von Trikots zu verstehen und eine kritische Reflexion darüber zu ermöglichen, wie das Fußballtrikot individuell definiert wird. KW - Fußballtrikot KW - Trikot KW - Arbeitsbekleidung KW - Identifikation KW - Distinktion KW - Kommunikationsdesign Y1 - 2023 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER - TY - THES A1 - Schlepütz, Nico T1 - News Flow : Nachrichten- und Informationsprozesse im digitalen Wandel N2 - "News Flow" Nachrichten- und Informationsprozesse im digitalen Wandel. In der digitalen Welt sind wir von Informationen aus unterschiedlichen Medien umgeben. Die ständige Verfügbarkeit führt zu Überforderung und Orientierungslosigkeit. Junge Menschen bevorzugen Streaming und Social Media gegenüber traditionellen Nachrichten. Angesichts globaler Krisen und Desinformation sind innovative Lösungen wichtig, um den Informationsfluss zu verbessern. "News Flow" ist eine digitale Anwendung für Alternativen des Nachrichtenkonsums. Sie berücksichtigt individuelle Bedürfnisse und nutzt moderne Technologien. Durch die visuelle Vermittlung wird das Interesse an Nachrichten gesteigert und junge Zielgruppen angesprochen. Diese Arbeit stellt sich den Herausforderungen des digitalen Wandels im Nachrichtenbereich und eröffnet eine neue Perspektive auf den Nachrichtenkonsum. KW - Informationsfluss KW - Good News Fokus KW - UX Design KW - UI Design KW - Alternative Konsumoption Y1 - 2023 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER - TY - THES A1 - Schmidt, Lucie T1 - „Keine Schmerzen in der Regel“ : Aufklärungskampagne zur Früherkennung der Krankheit Endometriose N2 - Jede zehnte Frau hat Endometriose. Hierbei entstehen Zysten und Entzündungen, welche sich beispielsweise an den Eierstöcken ansiedeln können. Wie kann es also sein, dass so viele noch nie was von dieser Erkrankung gehört haben? Mit der online Aufklärungskampagne „ Keine Schmerzen in der Regel“ soll sich das ändern. In vielen Fällen werden Beschwerden der Endometriose fälschlicherweise als normale Menstruationsbeschwerden abgetan. Die Differenzierung zwischen normal und nicht normal misslingt. Die Aufmerksamkeit von Mädchen und Frauen, die sich in den nicht normalen Aspekten wiederfinden, soll erregt werden. Dafür werden vier Symptome visualisiert und gegenübergestellt. Zusätzlich bietet ein Schnellcheck weitere Informationen. Diese Kampagne soll dem Problem der Unbekanntheit von Endometriose entgegenwirken und ein gesellschaftliches Bewusstsein für sie schaffen. KW - Aufklärungskampagne KW - Endometriose KW - Krankheit KW - Kommunikationsdesign Y1 - 2023 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER - TY - CHAP A1 - Groß, Rolf Fritz A1 - Thulfaut, Christian A1 - Renz, Ulrich ED - Jamal, Rahman ED - Jaschinski, Hans T1 - On-Line Simulation mit LabView: Experimentelle und numerische Analyse homogener Gasphasenreaktionen aus Kraftwerksprozessen, T2 - Virtuelle Instrumente in der Praxis. Begleitband zum Kongress VIP 2000 N2 - The institute of heat transfer and air conditioning at the Aachen University of Technology operates several test facilities in order to investigate homogeneous and catalytical processes for the reduction of gaseous pollutants (e.g. nitrous oxide) of flue gases in a tempeature range up to 900°C. One test facility consists of a stainless steel reactor in which the influence of reducing additives can be investigated. The software tool, created with LabVIEW 5.01, offers the possibility to measure, visualize and control all relevant physical quantities and to gain a numerical solution of the problem by solving the one dimensional, steady state conservation equations. N2 - Die bei Kohlekraftwerksprozessen entstehenden Rauchgase enthalten einen nicht unerheblichen Teil an Schadgaskomponenten (z.B. Stickoxide), die aus dem Gasstrom entfernt werden müssen. Im Rahmen von Forschungsvorhaben des BMBF und verschiedener Industriepartner betreibt der Lehrstuhl für Wärmeübertragung und Klimatechnik der RWTH Aachen Pilotanlagen und Prüfstände für Untersuchungen auf dem Gebiet der homogenen und heterogen-katalytischen Schadstoffreduktion heißer Rauchgase bei Temperaturen bis zu 900 °C. Für die Erforschung der Minderungspotentiale geeigneter, auf Distickstoffoxid reduzierend wirkender Additive, wie Wasserstoffperoxid, oder auch Katalysatoren, befindet sich ein Reaktor in Betrieb, der eine Untersuchung der Reaktionskinetik bei der Entfernung von Schadgaskomponenten aus einem lnertgasstrom ermöglicht. Wesentlich für den Erfolg der Forschungsarbeit ist eine auf das spezielle Projekt genau abgestimmte Meß- und Regelungstechnik. Neben der Auswahl geeigneter Hardwarekomponenten ist auch die Softwareentwicklung unter einer leistungsstarken und zuverlässigen Programmierumgebung von großer Bedeutung. Hierbei dient die unter LabVIEW 5.01 entwickelte Datenerfassung- und Auswertesoftware zum einen der Messung, Visualisierung und Regelung der relevanten Temperaturen, Drücke, Konzentrationen und Volumenströme einzelner Gaskomponenten. Zum anderen ermöglicht sie parallel eine numerische Simulation der Vorgänge innerhalb des Reaktors zur Anpassung reaktionskinetischer Parameter aus den sich ergebenden Versuchsdaten durch Lösung eindimensionaler, stationärer Erhaltungsgleichungen. Y1 - 2000 SN - 3-7785-2789-4 (print) SP - 103 EP - 108 PB - Hüthig CY - Heidelberg ER - TY - GEN A1 - Steuer-Dankert, Linda A1 - Bernhard, Sebastian A1 - Langolf, Jessica A1 - Leicht-Scholten, Carmen T1 - About the paradox of sustainable production and what we can do about it! T2 - Joint SCORAI-ERSCP-WUR conference on transforming consumption-production systems toward just and sustainable futures (SCP23) N2 - Sustainability is playing an increasingly important role. Not least due to the definition of the sustainable development goals (SDGs) in the framework of the agenda 2030 by the United Nations (UN) in 2015 (United Nations, n.d.), it has become clear that the cooperation of different actors is needed to achieve the defined 17 goals. Industry, as a global actor, has a special role to play in this. In the course of sustainable production processes and chains, the industry is confronted with the responsibility of reflecting on the consequences of its own trade on an ecological, economic, and also social level and deriving measures that, according to the definition of sustainability (Hauff, 1987), will also enable future generations to satisfy their needs. While the ecological pillar of sustainability is already being addressed by different industrial initiatives (Deloitte, 2021), it is questionable to what extent the economic and, above all, the social pillars of sustainability also play a decisive role. Accordingly, it is questionable to what extent sustainability in its triad of social, ecological, and economic aspects is taken into account holistically at all, and thus to what extent the industry contributes to achieving the 17 goals defined by the UN. This paper presents a qualitative study that explores these questions. Interviewing 31 representatives from the manufacturing industry in Germany, results indicate a Paradox of Sustainable Production expressed by a theoretical reflection of the need for focusing on people in production processes on the one hand and a lack of addressing the social pillar of sustainability in concepts on the other hand. However, while it is a troublesome finding given the striking need for sustainable development (The-Sustainable-Development-Goals-Report-2022; Kropp 2019; von Hauff 2021; Roy and Singh 2017), the paradox directly lays out a path of resolving it. This is because, given its nature, we can see that we could resolve it via the implementation of strong educational efforts trying to help the respective people of the manufacturing industry to understand the holistic and interdependent character of sustainable development (The-Sustainable-Development-Goals-Report-2022). Y1 - 2023 N1 - Volltext auf dem Opus-Server verfügbar ER - TY - GEN A1 - Steuer-Dankert, Linda A1 - Berg-Postweiler, Julia A1 - Leicht-Scholten, Carmen T1 - One does not fit all: applying anti-bias trainings in academia T2 - Twenty-third international conference on diversity in organizations, communities & nations June 22 - 23, 2023 Toronto Metropolitan University, Rogers Communication Centre Toronto, Canada N2 - Anti-bias trainings are increasingly demanded and practiced in academia and industry to increase employees’ sensitivity to discrimination, racism, and diversity. Under the heading of “Diversity Management”, anti-bias trainings are mainly offered as one-off workshops intending to raise awareness of unconscious biases, create a diversity-affirming corporate culture, awake awareness of the potential of diversity, and ultimately enable the reflection of diversity in development processes. However, coming from childhood education, research and scientific articles on the sustainable effectiveness of anti-bias in adulthood, especially in academia, are very scarce. In order to fill this research gap, the paper explores how sustainable the effects of individual anti-bias trainings on the behavior of participants are. In order to investigate this, participant observation in a qualitative pre-post setting was conducted, analyzing anti-bias trainings in an academic context. Two observers actively participated in the training sessions and documented the activities and reflection processes of the participants. Overall, the results question the effectiveness of single anti-bias trainings and show that a target-group adaptive approach is mandatory due to the background of the approach in early childhood education. Therefore, it can be concluded that anti-bias work needs to be adapted to the target group’s needs and reality of life. Furthermore, the study reveals that single anti-bias trainings must be embedded in a holistic diversity management approach to stimulate sustainable reflection processes among the target group. This paper is one of the first to scientifically evaluate anti-bias training effectiveness, especially in engineering sciences and the university context. KW - Academia KW - Engineering Habitus KW - Organizational Culture KW - Diversity Management KW - Anti-Bias Y1 - 2023 ER - TY - JOUR A1 - Eggert, Mathias A1 - Kling, Rene T1 - How to distribute charging requests of electronic vehicles? A reservation-based approach JF - International Journal of Intelligent Transportation Systems Research N2 - The number of electronic vehicles increase steadily while the space for extending the charging infrastructure is limited. In particular in urban areas, where parking spaces in attractive areas are famous, opportunities to setup new charging stations is very limited. This leads to an overload of some very attractive charging stations and an underutilization of less attractive ones. Against this background, the paper at hand presents the design of an e-vehicle reservation system that aims at distributing the utilization of the charging infrastructure, particularly in urban areas. By applying a design science approach, the requirements for a reservation-based utilization approach are elicited and a model for a suitable distribution approach and its instantiation are developed. The artefact is evaluated by simulating the distribution effects based on data of real charging station utilizations. KW - Simulation KW - Parking KW - Charging station KW - Utilization improvement KW - Reservation system KW - Electronic vehicle Y1 - 2023 U6 - https://doi.org/10.1007/s13177-023-00367-z SN - 1868-8659 N1 - Corresponding author: Mathias Eggert VL - 21 IS - 2023 SP - 437 EP - 460 PB - Springer CY - Berlin, Heidelberg, New York ER - TY - JOUR A1 - Groß, Rolf Fritz A1 - Timmer, H. T1 - Energetische und betriebswirtschaftliche Bewertung von Kühlsystemen für Kühllager JF - HLH. Heizung, Lüftung/Klima, Haustechnik KW - Heizung KW - Lüftung KW - Klimatechnik KW - Lüftungstechnik KW - Haustechnik Y1 - 1998 SN - 1436-5103 VL - 49 IS - 9 SP - 74 EP - 77 PB - Springer CY - Düsseldorf ER - TY - CHAP A1 - Groß, Rolf Fritz A1 - Hecken, M. A1 - Renz, Ulrich ED - Dittler, A. ED - Hemmer, G. ED - Kasper, G. T1 - Hot gas filtration with ceramic filter candles: experimental and numerical investigations on fluid flow during element cleaning T2 - High temperature gas cleaning. Vol. 2 N2 - Ceramic hot gas filters are widely used in combined cycles based on pressurised fluidised beds. They fulfil most of the demands with respect to cleaning efficiency and long time durability, but their operation regarding the consumption of pulse gas and energy still has to be optimised. Experimental investigations were carried out to measure the flow field, the pressure and the gas temperature inside the filter candle during pulse jet cleaning. These results are compared with the results of a numerical procedure based on a solution of the two - dimensional conservation equations for momentum and energy. The observed difficulties handling different flow regimes like highly turbulent flow as well as Darcy flow simultaneously are discussed. KW - 20 fossil-fueled power plants KW - hot gas cleanup KW - ceramics KW - filtration KW - gas flow Y1 - 1999 SN - 3-9805220-1-6 N1 - 4th International Symposium and Exhibition on Gas Cleaning at High Temperatures, 22.-24.09.1999, Karlsruhe SP - 862 EP - 873 PB - KIT Institut für Mechanische Verfahrenstechnik und Mechanik CY - Karlsruhe ER - TY - INPR A1 - Bornheim, Tobias A1 - Niklas, Grieger A1 - Blaneck, Patrick Gustav A1 - Bialonski, Stephan T1 - Preprint: Speaker attribution in German parliamentary debates with QLoRA-adapted large language models T2 - Journal for Language Technology and Computational Linguistics N2 - The growing body of political texts opens up new opportunities for rich insights into political dynamics and ideologies but also increases the workload for manual analysis. Automated speaker attribution, which detects who said what to whom in a speech event and is closely related to semantic role labeling, is an important processing step for computational text analysis. We study the potential of the large language model family Llama 2 to automate speaker attribution in German parliamentary debates from 2017-2021. We fine-tune Llama 2 with QLoRA, an efficient training strategy, and observe our approach to achieve competitive performance in the GermEval 2023 Shared Task On Speaker Attribution in German News Articles and Parliamentary Debates. Our results shed light on the capabilities of large language models in automating speaker attribution, revealing a promising avenue for computational analysis of political discourse and the development of semantic role labeling systems. Y1 - 2023 U6 - https://doi.org/10.48550/arXiv.2309.09902 N1 - Veröffentlichte Version verfügbar unter: https://doi.org/10.21248/jlcl.37.2024.244 ER - TY - JOUR A1 - Thulfaut, Christian A1 - Groß, Rolf Fritz T1 - Experimentelle Untersuchung der Luftstromvermischung in Hybridzellenkühltürmen JF - HLH. Heizung, Lüftung/Klima, Haustechnik N2 - Zwangsbelüftete Nasskühltürme haben im Gegensatz zur Trockenkühlung bei naßkaltem Wetter Nebelschwaden zur Folge. Dagegen ist bei Naßkühlung die spezifische Kühlleistung durch abgeführte Kondensationswärme höher als bei der Trockenkühlung. Hybridzellenkühltürme kombinieren beide Methoden, so daß ein Mischstrom beider Abluftströme die Wasserdampf-Sättigungsgrenze nicht überschreitet. Durch das Mischungsverhältnis kann man den gewünschten Sättigungsgrad einstellen. Je dichter dieser an der Sättigungsgrenze liegt, desto höher ist die Kühlleistung. Der von unten zugeführte Luftstrom der Naßkühlung und der seitlich zugeführte trockene Abluftstrom müssen sehr gut durchmischt werden, um über den gesamten Austrittsquerschnitt des Kühlturms die Sättigungsgrenze nicht zu überschreiten. In einem maßstabsgerechten Modell wurde der Mischungsgrad mit und ohne Einbauten untersucht. Über ein Raster von 10 mal 10 Punkten wurde die örtliche Temperaturverteilung ermittelt. Wärmebilanzen ergeben dann die Mischungsgüte in einer Ebene oberhalb der Zellenkrone. Während ohne Mischeinbauten der Trockenluftanteil in der Mitte des Querschnitts bei unter 15 % liegt erhöhen Einbauten den Trockenluftanteil auf 30 % bis über 40 %. Dabei wurde die Trockenluft auf jeder Kühlturmseite durch 4 konisch zulaufende, unten offene und oben geschlitzte Einbauten kanalisiert. Die Nassluft wurde durch eine im Querschnitt dreieckige Rinne in Richtung der Trockenluftauslässe umgelenkt. Im Raster leicht zu lokalisierende Abweichungen vom gewünschten Mittelwert zeigen Potential für die weitere Verbesserung der Einbauten. KW - Trockenkühlturm KW - Nasskühlturm KW - kombiniertes Verfahren KW - Mischen KW - Abluft Y1 - 2000 SN - 1436-5103 VL - 51 IS - 8 SP - 48 EP - 49 PB - Springer CY - Düsseldorf ER - TY - RPRT A1 - Ayar, A. A1 - Fielenbach, C. A1 - Groß, Rolf Fritz A1 - Holfeld, T. A1 - Lockemann, S. A1 - Severin, C. A1 - Thulfaut, Christian A1 - Hillemacher, B. T1 - Druckkohlenstaubverbrennung von rheinischer Braunkohle : Abschlussbericht T1 - Pressure combustion of rhenish brown coal : final report N2 - Im Rahmen des Forschungsschwerpunkts 3 wurde experimentell und theoretisch die NO{sub x}-Bildung und -Reduktion bei der Druckkohlenstaubverbrennung untersucht. Der zuvor beschriebene Einfluss der Kohlemahlung auf die Flamme konnte auch anhand der NO{sub x}-Messungen an der DKSF-Anlage Aachen bestaetigt werden. Waehrend mit Braunkohle im Staubfeuerungsbetrieb noch keine eindeutige Druckabhaengigkeit nachgewiesen werden konnte, haben vom Lehrstuhl durchgefuehrte NO{sub x}-Messungen an der DKSF-Anlage Dorsten im Schmelzkammerfeuerungsbetrieb mit der Steinkohle Spitzbergen zwischen 9 und 13 bar ein Absinken der Stickoxidkonzentrationen mit steigendem Druck ergeben. Fuer die rheinische Braunkohle soll dieser Druckeinfluss in den naechsten Versuchsfahrten ausfuehrlicher untersucht werden. Es wurde anhand von numerischen Simulationen zu einer Braunkohleflamme der 6. Versuchsfahrt ein Vergleich zwischen der NO{sub x}-Modellierung im Standard-FLUENT-Code und in dem mit User Defined Subroutines der international flame research foundation (IFRF), Ijmuiden, erweiterten FLUENT-Code vorgenommen. Es zeigte sich, dass bei der Modellierung der Stickoxidbildung die unterschiedlich vorhergesagten Flammentemperaturen eine entscheidende Rolle spielen. Eine genauere Analyse der NO{sub x}-Modelle im Vergleich zu Messergebnissen ist bei einer Schmelzkammerfeuerung mit einer stabilen Flamme vorzunehmen. Es wurden zusaetzlich Messungen zur Untersuchung der Kinetik homogener Gasphasenreaktionen in Rauchgasen an einem Stahlreaktor durchgefuehrt. Dabei wurde sowohl der thermisch bedingte als auch der durch zudosierte Additive katalysierte Abbau nitroser Komponenten betrachtet. Vergleichend wurden mit einem am Lehrstuhl entwickelten Programm die Kinetik beschrieben. Hierbei wird mit einer Sensitivitaetsanalyse eine Reduzierung der detaillierten Darstellung der Reaktionskinetik erreicht, die es erlaubt, mit einem CFD-Code wie FLUENT zwei- und dreidimensionale Rechnungen zum Abbau verschiedener Rauchgaskomponenten durchzufuehren. Die Uebereinstimmung zwischen ein- und zweidimensionalen Rechnungen und den Messungen ist gut. N2 - NOx formation and reduction in the coal combustion process was investigated both experimentally and theoretically. The influence of coal grain size described in earlier publications was proved by the measurements at the DKSF test facility at Aachen. While no pressure dependence was established so far for lignite, measurements on Spitzbergen coal at 9 - 13 bar showed a decrease in NOx concentrations with increasing pressure. This effect will be investigated for Rhenish brown coal in further experiments. Modelling by the standard FLUENT code and by the user defined subroutines of the FLUENT code developed by the International Flame Research Foundation (IFRF), Ijmuiden, showed that the different predictions of flame temperatures have a decisive role in the modelling of NOx formation. A more accurate analysis of the NOx models as compared to ther measurements will be carried out in a melting chamber furnace with a stable flame. Additionally, measurements were carried out for investigating the kinetics of homogeneous gaseous phase reactions in flue gases, i.e. the thermal and additive-catalysed degradation of nitrous components was investigated. The kinetics of the process was also described by a code developed at Aachen University. On the base of a sensitivity analysis, a reduction of the detailed modelling of the reaction kinetics is achieved which permits 2D and 3D calculations on the decomposition of different flue gas components using a CFD code like FLUENT. The 1D and 2D calculations and the measurements were found to be in good agreement. Y1 - 2003 N1 - Druckkohlenstaubverbrennung von rheinischer Braunkohle Förderkennzeichen: 0327072 Abschlussbericht zum Forschungsvorhaben ausführende Stelle: Lehrstuhl fur Wärmeübertragung und Klimatechnik der RWTH Aachen Professor Dr.-Ing. U. Renz ER - TY - CHAP A1 - Eggert, Mathias A1 - Zähl, Philipp M. A1 - Wolf, Martin R. A1 - Haase, Martin ED - Cooper, Kendra M.L. ED - Bucchiarone, Antonio T1 - Applying leaderboards for quality improvement in software development projects T2 - Software Engineering for Games in Serious Contexts N2 - Software development projects often fail because of insufficient code quality. It is now well documented that the task of testing software, for example, is perceived as uninteresting and rather boring, leading to poor software quality and major challenges to software development companies. One promising approach to increase the motivation for considering software quality is the use of gamification. Initial research works already investigated the effects of gamification on software developers and come to promising. Nevertheless, a lack of results from field experiments exists, which motivates the chapter at hand. By conducting a gamification experiment with five student software projects and by interviewing the project members, the chapter provides insights into the changing programming behavior of information systems students when confronted with a leaderboard. The results reveal a motivational effect as well as a reduction of code smells. KW - Leaderboard KW - Gamification KW - Software testing KW - Software development Y1 - 2023 SN - 978-3-031-33337-8 (Print) SN - 978-3-031-33338-5 (Online) U6 - https://doi.org/10.1007/978-3-031-33338-5_11 SP - 243 EP - 263 PB - Springer CY - Cham ER - TY - JOUR A1 - Wendlandt, Tim A1 - Koch, Claudia A1 - Britz, Beate A1 - Liedek, Anke A1 - Schmidt, Nora A1 - Werner, Stefan A1 - Gleba, Yuri A1 - Vahidpour, Farnoosh A1 - Welden, Melanie A1 - Poghossian, Arshak A1 - Schöning, Michael Josef T1 - Facile Purification and Use of Tobamoviral Nanocarriers for Antibody-Mediated Display of a Two-Enzyme System JF - Viruses N2 - Immunosorbent turnip vein clearing virus (TVCV) particles displaying the IgG-binding domains D and E of Staphylococcus aureus protein A (PA) on every coat protein (CP) subunit (TVCVPA) were purified from plants via optimized and new protocols. The latter used polyethylene glycol (PEG) raw precipitates, from which virions were selectively re-solubilized in reverse PEG concentration gradients. This procedure improved the integrity of both TVCVPA and the wild-type subgroup 3 tobamovirus. TVCVPA could be loaded with more than 500 IgGs per virion, which mediated the immunocapture of fluorescent dyes, GFP, and active enzymes. Bi-enzyme ensembles of cooperating glucose oxidase and horseradish peroxidase were tethered together on the TVCVPA carriers via a single antibody type, with one enzyme conjugated chemically to its Fc region, and the other one bound as a target, yielding synthetic multi-enzyme complexes. In microtiter plates, the TVCVPA-displayed sugar-sensing system possessed a considerably increased reusability upon repeated testing, compared to the IgG-bound enzyme pair in the absence of the virus. A high coverage of the viral adapters was also achieved on Ta2O5 sensor chip surfaces coated with a polyelectrolyte interlayer, as a prerequisite for durable TVCVPA-assisted electrochemical biosensing via modularly IgG-assembled sensor enzymes. KW - biosensor KW - horseradish peroxidase (HRP) KW - glucose oxidase (GOx) KW - enzyme cascade KW - turnip vein clearing virus (TVCV) KW - tobacco mosaic virus (TMV) Y1 - 2023 U6 - https://doi.org/doi.org/10.3390/v15091951 SN - 1999-4915 N1 - This article belongs to the Special Issue "Tobamoviruses 2023" VL - 9 IS - 15 PB - MDPI CY - Basel ER - TY - JOUR A1 - Bertz, Morten A1 - Molinnus, Denise A1 - Schöning, Michael Josef A1 - Homma, Takayuki T1 - Real-time monitoring of H₂O₂ sterilization on individual bacillus atrophaeus spores by optical sensing with trapping Raman spectroscopy JF - Chemosensors N2 - Hydrogen peroxide (H₂O₂), a strong oxidizer, is a commonly used sterilization agent employed during aseptic food processing and medical applications. To assess the sterilization efficiency with H₂O₂, bacterial spores are common microbial systems due to their remarkable robustness against a wide variety of decontamination strategies. Despite their widespread use, there is, however, only little information about the detailed time-resolved mechanism underlying the oxidative spore death by H₂O₂. In this work, we investigate chemical and morphological changes of individual Bacillus atrophaeus spores undergoing oxidative damage using optical sensing with trapping Raman microscopy in real-time. The time-resolved experiments reveal that spore death involves two distinct phases: (i) an initial phase dominated by the fast release of dipicolinic acid (DPA), a major spore biomarker, which indicates the rupture of the spore’s core; and (ii) the oxidation of the remaining spore material resulting in the subsequent fragmentation of the spores’ coat. Simultaneous observation of the spore morphology by optical microscopy corroborates these mechanisms. The dependence of the onset of DPA release and the time constant of spore fragmentation on H₂O₂ shows that the formation of reactive oxygen species from H₂O₂ is the rate-limiting factor of oxidative spore death. KW - DPA (dipicolinic acid) KW - sterilization KW - Bacillus atrophaeus spores KW - optical trapping KW - Raman spectroscopy KW - optical sensor setup Y1 - 2023 U6 - https://doi.org/10.3390/chemosensors11080445 SN - 2227-9040 N1 - This article belongs to the Special Issue "Biosensors and Chemical Sensors for Food and Healthcare Monitoring—Celebrating the 10th Anniversary" VL - 8 IS - 11 PB - MDPI CY - Basel ER - TY - THES A1 - Groß, Rolf Fritz T1 - Zur Kinetik homogener Gasphasenreaktionen nitroser Komponenten in Rauchgasen einer kohlebefeuerten Wirbelschicht KW - Kohlefeuerung KW - Wirbelschichtfeuerung KW - Stickstoffoxide KW - Reduktion KW - Rohrreaktor Y1 - 2002 SN - 3-8322-0004-5 (softcover) SN - 3-8322-0004-6 (elektronisch) N1 - Dissertation RWTH Aachen PB - Shaker CY - Aachen ER - TY - JOUR A1 - Groß, Rolf Fritz A1 - Berger, J. A1 - Groß, H. T1 - Gebäudeautomation - Betriebsdatenerfassung und Gebäudeleittechnik im Klartext T1 - Operating data- and facility management in clear JF - HLH. Heizung, Lüftung/Klima, Haustechnik KW - Heizung KW - Lüftung KW - Klimatechnik KW - Lüftungstechnik KW - Haustechnik Y1 - 2003 SN - 1436-5103 VL - 54 IS - 2 SP - 81 PB - Springer CY - Düsseldorf ER - TY - JOUR A1 - Groß, Rolf Fritz A1 - Berger, J. T1 - Quo Vadis - Ausblick in die Gebäudeleittechnik der Zukunft T1 - Whitherfacility management? An outlook to the future JF - HLH. Heizung, Lüftung/Klima, Haustechnik N2 - Auf dem Weg zum vernetzten Haus stoßen Hersteller und Planer, insbesondere im privaten Wohnungsbau, zur Zeit noch auf erhebliche Widerstände bei der Durchdringung des Marktes. N2 - Producers and planners of facility management systems are still faced with building owners' reluctance, especially when it comes to private homes. Y1 - 2005 SN - 1436-5103 VL - 56 IS - 1 SP - 39 EP - 41 PB - Springer CY - Düsseldorf ER - TY - BOOK A1 - Heuermann, Holger T1 - Hochfrequenztechnik. Komponenten und Mess-, Funk-, RFID- sowie Lokalisierungssysteme N2 - Dieses Lehr- und Fachbuch vermittelt anschaulich die Grundlagen der HF-Technik, gibt konkrete Beschreibungen für den Entwurf von linearen Komponenten aus Bauteilen wie auch Leitungen für High-Speed- und HF-Schaltungen. Dem Leser wird vermittelt, wie Bauteile modelliert und Schaltungen synthetisiert und optimiert werden. Mit Hilfe frei verfügbarer Simulationssoftware können GHz-Schaltungen selbst entwickelt werden. Viele Übungsbeispiele ermöglichen die Eigenkontrolle des Wissensstandes. Weiterhin werden komplexe nichtlineare Komponenten wie Hochfrequenzmischer, Oszillatoren und Synthesegeneratoren in ihrer Funktionalität dargestellt. Die neuen Mixed-Mode-Streuparameter sowie deren Leitungs- und Schaltungstechnik für Anwendungen der schnellen Digital- und der modernen HF-Technik sind ausführlich beschrieben. Es wird auf Systeme für folgende Bereiche eingegangen: Streuparametermesstechnik, verschiedene Funktechniken, UHF-RFID und Lokalisierung- und Ortung. Dem Leser wird somit ermöglicht, komplexe GHz-Schaltungen insbesondere mit Halbleiter-, SMD- und LTCC-Schaltungen zu entwickeln. Y1 - 2023 SN - 978-3-658-37825-7 (Print) SN - 978-3-658-37826-4 (eBook) PB - Springer Fachmedien CY - Wiesbaden ET - 4 ER - TY - RPRT A1 - Höfler, Matthias A1 - Groß, Rolf Fritz T1 - Optimierung der Oxidationskinetik von Sulfit zu Sulfat durch effiziente feinblasige Belüftung bei Anlagen zur Rauchgasentschwefelung fossil befeuerter Kraftwerke und Industrieanlagen mittels Seewasser ("Optiox") N2 - Das Forschungsvorhaben Optiox beschäftigt sich mit der Optimierung eines Belüftungsbeckens zur Rauchgasentschwefelung fossil befeuerter Kraftwerke mittels Seewasser. Unter Neutralisierung der entstehenden Hydroniumionen (H3O+) durch die natürliche Alkalität des Seewassers dissoziiert Schwefeldioxid aus dem Rauchgase im vorgeschalteten Absorber beim Phasenübergang von der Gas- in die Flüssigphase zu Sulfiten. Im Belüftungsbecken werden diese Sulfite mittels eingeblasener Luft zu Sulfaten oxidiert, was zu einer geringen Erhöhung der Sulfatfracht vor Einleitung ins Meer führt, die unterhalb der natürlichen Schwankungen liegt. Daneben dient das Belüftungsbecken der Konditionierung des Seewassers hinsichtlich pH-Wert und Sauerstoffgehalt und ist mit hoch effizienten Belüftern ausgestattet, deren Spezifikation den jeweiligen Randbedingungen, wie Abscheideleistung des Absorbers, Beckengeometrie sowie lokalen Gegebenheiten angepasst wird. Y1 - 2016 N1 - Projektlaufzeit: 10/2012 – 09/2015 Gefördert durch: BMBF – Förderkennlinie Ingenieurnachwuchs Kooperationspartner: Doosan Lentjes GmbH, Ratingen, FH Aachen, Fachbereich Energietechnik, Prof. Dr.-Ing. Rolf Groß ER - TY - THES A1 - Götz, Daniela T1 - Entwicklung eines Erscheinungsbildes für das Start-up-Unternehmen CoArea N2 - Diese Bachelorarbeit befasst sich mit dem Corporate Design des aufstrebenden Startups "CoArea". Seine innovative Plattform vermittelt ungenutzte Flächen im urbanen Raum und bringt Flächenbedarf und -bereitstellung intelligent zusammen. Die Arbeit untersucht, wie das Erscheinungsbild von CoArea das Unternehmen als modern, nachhaltig und ressourcenschonend positioniert. Durch das neu gestaltete Corporate Design wird diese besondere Herangehensweise zur effizienten Nutzung begrenzter Ressourcen unserer Umwelt durch CoArea deutlich und nach außen getragen. CoArea strebt danach, die positive Entwicklung der Städte voranzutreiben und die soziale Nachhaltigkeit durch den Austausch und die Interaktion zwischen verschiedenen Menschen und Gemeinschaften zu fördern. KW - Start-up KW - Nachhaltigkeit KW - Flächennutzung KW - Schraffur KW - Ressourcenschonung Y1 - 2023 PB - FH Aachen CY - Aachen ER - TY - THES A1 - Hoffmann, Noa T1 - SpineSans : Erkundung des generativen Potentials modularer Typografie N2 - Spine Sans – Erkundung des generativen Potenzials modularer Typografie. „Spine Sans“ ist eine dekorative Schriftfamilie, die mit modularen Limitationen gestaltet wurde. Kleinbuchstaben sind in eine obere und untere Hälfte unterteilt, zwischen denen Raum für spannende generative Effekte entsteht. Schriftzeichen und Effekte wurden unabhängig voneinander, aber auf dem gleichen Spaltenraster gestaltet und passen daher nahtlos zusammen. Beispielhafte Varianten der „Spines“ können in einem speziell programmierten Web-Interface an selbst geschriebenen Text erkundet werden. Die Galerie an Optionen präsentiert mögliche Resultate für die spielerische Kombination. Die zwei Schriftschnitte „Spine Sans Bold“ und „Spine Sans Double“ können auch gemischt werden. Weiter ergänzbar um maßgeschneiderte Varianten, kann „Spine Sans“ besonders in interaktiven oder animierten Medien effektiv verschiedenste Eindrücke vermitteln. KW - Typografie KW - Generative Gestaltung KW - Geometrisch KW - Modularität KW - Grotesk Y1 - 2023 PB - FH Aachen CY - Aachen ER - TY - THES A1 - Hosseinpour, Seywan T1 - Velum : Zensur des Visuellen im Iran N2 - Dieses multimediale Projekt thematisiert Zensur aus verschiedenen Dimensionen in totalitären, religiös-patriarchalischen Ländern, insbesondere im Iran. Dadurch wird versucht, mit einem denunzierenden Ansatz zu zeigen, wie Bilder zensiert werden und welche Auswirkungen diese zensierten Bilder auf Betrachter:innen haben. Dabei ist es auch wichtig, wie das Unsichtbare analysiert und verstanden wird. Die Opposition zwischen dem Akt des Visualisierens/Sichtbarmachens und Verbergens/Unsichtbarmachens in den meisten Bildern impliziert die Dialektik von Verhüllung und Enthüllung. Das Projekt »Velum« ermöglicht es den Betrachter:innen, die Zensurpraktiken in totalitär-religiösen Ländern kennenzulernen und zu erfahren, inwieweit die Zensur das tägliche Leben durchdrungen und beeinflusst hat –in der Kunst, der Literatur, den Medien usw. Ein Phänomen, das sogar die Privatsphäre des Individuums beeinträchtigt. KW - Fotoinstallation KW - Multimedia KW - Siebdruck KW - Zensur KW - Selbstzensur Y1 - 2023 PB - FH Aachen CY - Aachen ER - TY - THES A1 - Leiwen, Sophie T1 - Steinreich : Mineralien des Siegerlands N2 - Der Aufbau und die Entstehung unseres Planeten sind untrennbar mit der Bildung von Gesteinen verbunden – diese setzen sich aus verschiedenen Mineralien zusammen. Sie sind in der Natur weit verbreitet und spielen eine entscheidende Rolle in unserem täglichen Leben. Obwohl vielen Menschen der Nutzen von Bodenschätzen bewusst ist, besteht ein geringes Wissen über deren Vorkommen und Relevanz. Für die wirtschaftliche Entwicklung des Siegerlandes beispielsweise waren der Abbau und der Handel mit Mineralien von großer Bedeutung. Insbesondere der langjährige Abbau von Eisenerz legte den Grundstein für die gesamte Metallindustrie der Region. Die Publikation visualisiert eine umfangreiche Sammlung Siegerländer Mineralien und vermittelt ein grundlegendes Verständnis von Mineralien. KW - Mineralien KW - Mineral KW - Siegerland KW - Gesteine KW - Eisenerz Y1 - 2023 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER - TY - CHAP A1 - Alhaskir, Mohamed A1 - Tschesche, Matteo A1 - Linke, Florian A1 - Schriewer, Elisabeth A1 - Weber, Yvonne A1 - Wolking, Stefan A1 - Röhrig, Rainer A1 - Koch, Henner A1 - Kutafina, Ekaterina ED - Röhrig, Rainer ED - Grabe, Niels ED - Haag, Martin ED - Hübner, Ursula ED - Sax, Ulrich ED - Schmidt, Carsten Oliver ED - Sedlmayr, Martin ED - Zapf, Antonia T1 - ECG matching: an approach to synchronize ECG datasets for data quality comparisons T2 - Proceedings of the 68th Annual Meeting of the German Association of Medical Informatics, Biometry, and Epidemiology e.V. (gmds) 2023 N2 - Clinical assessment of newly developed sensors is important for ensuring their validity. Comparing recordings of emerging electrocardiography (ECG) systems to a reference ECG system requires accurate synchronization of data from both devices. Current methods can be inefficient and prone to errors. To address this issue, three algorithms are presented to synchronize two ECG time series from different recording systems: Binned R-peak Correlation, R-R Interval Correlation, and Average R-peak Distance. These algorithms reduce ECG data to their cyclic features, mitigating inefficiencies and minimizing discrepancies between different recording systems. We evaluate the performance of these algorithms using high-quality data and then assess their robustness after manipulating the R-peaks. Our results show that R-R Interval Correlation was the most efficient, whereas the Average R-peak Distance and Binned R-peak Correlation were more robust against noisy data. KW - Electrocardiography KW - Wearable electronic device KW - Sensors comparison KW - Time-series synchronization Y1 - 2023 SN - 978-1-64368-428-4 (Print) SN - 978-1-64368-429-1 (Online) U6 - https://doi.org/10.3233/SHTI230718 N1 - Proceedings of the 68th Annual Meeting of the German Association of Medical Informatics, Biometry, and Epidemiology e.V. (gmds) 2023, 17. - 21.9.23, Heilbronn, Germany Part of the series: Studies in Health Technology and Informatics VL - 307 SP - 225 EP - 232 PB - IOS Press ER - TY - CHAP A1 - Groß, Rolf Fritz T1 - Möglichkeiten und Grenzen für Forschung an Fachhochschulen T2 - Smart Building Convention und BIMconvention in Aachen im September Y1 - 2018 N1 - 10. und 11. September 2018, Aachen ER - TY - CHAP A1 - Duran Paredes, Ludwin A1 - Mottaghy, Darius A1 - Herrmann, Ulf A1 - Groß, Rolf Fritz T1 - Online ground temperature and soil moisture monitoring of a shallow geothermal system with non-conventional components T2 - EGU General Assembly 2020 N2 - We present first results from a newly developed monitoring station for a closed loop geothermal heat pump test installation at our campus, consisting of helix coils and plate heat exchangers, as well as an ice-store system. There are more than 40 temperature sensors and several soil moisture content sensors distributed around the system, allowing a detailed monitoring under different operating conditions.In the view of the modern development of renewable energies along with the newly concepts known as Internet of Things and Industry 4.0 (high-tech strategy from the German government), we created a user-friendly web application, which will connect the things (sensors) with the open network (www). Besides other advantages, this allows a continuous remote monitoring of the data from the numerous sensors at an arbitrary sampling rate.Based on the recorded data, we will also present first results from numerical simulations, taking into account all relevant heat transport processes.The aim is to improve the understanding of these processes and their influence on the thermal behavior of shallow geothermal systems in the unsaturated zone. This will in turn facilitate the prediction of the performance of these systems and therefore yield an improvement in their dimensioning when designing a specific shallow geothermal installation. Y1 - 2020 N1 - EGU General Assembly 2020, Online, 4–8 May 2020 ER - TY - CHAP A1 - Engelmann, Ulrich M. A1 - Baumann, Martin ED - Thomann, Hermann ED - Träger, Thomas T1 - Moderationsexpertise für QMBs – die Methoden T2 - Qualitätsmanagement in Dienstleistungsunternehmen N2 - Damit Sie als Moderator effektiv und professionell moderieren können, sollten Sie die entsprechenden Methoden kennen. Mit den richtigen Methoden können Sie Diskussionen leiten, Konflikte lösen, die Teilnehmer motivieren und dafür sorgen, dass die Ziele der Veranstaltung erreicht werden. Außerdem helfen sie Ihnen, eine positive Atmosphäre zu schaffen und das Interesse der Teilnehmer zu halten. In diesem zweiten Beitrag der mehrteiligen Serie lernen Sie die grundsätzlichen Methoden kennen, um erfolgreiche Teamsitzungen, Arbeitsgruppentreffen, Kick-offs und Meetings durchzuführen. Y1 - 2023 SN - 978-3-8249-0473-0 SP - Kapitel 08631 PB - TÜV-Verlag CY - Köln ER - TY - CHAP A1 - Engelmann, Ulrich M. A1 - Baumann, Martin ED - Lindinger, Markus ED - Bartsch, Oliver T1 - Moderationsexpertise – die Methoden T2 - IT-Servicemanagement N2 - Damit Sie als Moderator effektiv und professionell moderieren können, sollten Sie die entsprechenden Methoden kennen. Mit den richtigen Methoden können Sie Diskussionen leiten, Konflikte lösen, die Teilnehmer motivieren und dafür sorgen, dass die Ziele der Veranstaltung erreicht werden. Außerdem helfen sie Ihnen, eine positive Atmosphäre zu schaffen und das Interesse der Teilnehmer zu halten. In diesem zweiten Beitrag der mehrteiligen Serie lernen Sie die grundsätzlichen Methoden kennen, um erfolgreiche Teamsitzungen, Arbeitsgruppentreffen, Kick-offs und Meetings durchzuführen. Y1 - 2023 SN - 978-3-8249-1154-7 SP - Kapitel 05531 PB - TÜV-Verlag CY - Köln ET - 54. Update ER - TY - JOUR A1 - Pfaff, Raphael T1 - Braking distance prediction for vehicle consist in low-speed on-sight operation: a Monte Carlo approach JF - Railway Engineering Science N2 - The first and last mile of a railway journey, in both freight and transit applications, constitutes a high effort and is either non-productive (e.g. in the case of depot operations) or highly inefficient (e.g. in industrial railways). These parts are typically managed on-sight, i.e. with no signalling and train protection systems ensuring the freedom of movement. This is possible due to the rather short braking distances of individual vehicles and shunting consists. The present article analyses the braking behaviour of such shunting units. For this purpose, a dedicated model is developed. It is calibrated on published results of brake tests and validated against a high-definition model for low-speed applications. Based on this model, multiple simulations are executed to obtain a Monte Carlo simulation of the resulting braking distances. Based on the distribution properties and established safety levels, the risk of exceeding certain braking distances is evaluated and maximum braking distances are derived. Together with certain parameters of the system, these can serve in the design and safety assessment of driver assistance systems and automation of these processes. KW - Freight rail KW - Shunting KW - Braking curves KW - Brake set-up KW - Driver assistance system Y1 - 2023 U6 - https://doi.org/10.1007/s40534-023-00303-7 SN - 2662-4753 (eISSN) SN - 2662-4745 (Print) VL - 31 IS - 2 SP - 135 EP - 144 PB - SpringerOpen ER - TY - CHAP A1 - Neugebauer, Georg A1 - Brutschy, Lucas A1 - Meyer, Ulrike A1 - Wetzel, Susanne ED - Garcia-Alfaro, Joaquin ED - Lioudakis, Georgios ED - Cuppens-Boulahia, Nora ED - Foley, Simon ED - Fitzgerald, William M. T1 - Privacy-preserving multi-party reconciliation secure in the malicious model T2 - DPM 2013, SETOP 2013: Data Privacy Management and Autonomous Spontaneous Security N2 - The problem of fair and privacy-preserving ordered set reconciliation arises in a variety of applications like auctions, e-voting, and appointment reconciliation. While several multi-party protocols have been proposed that solve this problem in the semi-honest model, there are no multi-party protocols that are secure in the malicious model so far. In this paper, we close this gap. Our newly proposed protocols are shown to be secure in the malicious model based on a variety of novel non-interactive zero-knowledge-proofs. We describe the implementation of our protocols and evaluate their performance in comparison to protocols solving the problem in the semi-honest case. KW - Privacy-enhancing technologies KW - Secure multi-party computation KW - Cryptographic protocols KW - Zero-knowledge proofs KW - Malicious model Y1 - 2014 SN - 978-3-642-54567-2 (Print) SN - 978-3-642-54568-9 (Online) U6 - https://doi.org/10.1007/978-3-642-54568-9_12 N1 - 8th International Workshop, DPM 2013, and 6th International Workshop, SETOP 2013, Egham, UK, September 12-13, 2013. Part of the Lecture Notes in Computer Science book series (LNSC,volume 8247) SP - 178 EP - 193 PB - Springer CY - Berlin ER - TY - JOUR A1 - Herzwurm, Georg A1 - Krams, Benedikt A1 - Pietsch, Wolfram A1 - Schockert, Sixten T1 - Report from the 3rd international workshop on requirements prioritization for customer oriented software development (RePriCo’12) JF - ACM SIGSOFT Software Engineering Notes N2 - Prioritization is an essential task within requirements engineering to cope with complexity and to establish focus properly. The 3rd Workshop on Requirements Prioritization for customer oriented Software Development (RePriCo’12) focused on requirements prioritization and adjacent themes in the context of customer oriented development of bespoke and standard software. Five submissions have been accepted for the proceedings and for presentation. The report summarizes and points out key findings. KW - Requirements relations KW - Discourse ethics KW - Tool support KW - Consensus KW - Requirements prioritization Y1 - 2012 U6 - https://doi.org/10.1145/2237796.2237817 SN - 0163-5948 VL - 37 IS - 4 SP - 32 EP - 34 PB - Association for Computing Machinery CY - New York ER - TY - CHAP A1 - Viehmann, Tarik A1 - Limpert, Nicolas A1 - Hofmann, Till A1 - Henning, Mike A1 - Ferrein, Alexander A1 - Lakemeyer, Gerhard ED - Eguchi, Amy ED - Lau, Nuno ED - Paetzel-Prüsmann, Maike ED - Wanichanon, Thanapat T1 - Winning the RoboCup logistics league with visual servoing and centralized goal reasoning T2 - RoboCup 2022: Robot World Cup XXV N2 - The RoboCup Logistics League (RCLL) is a robotics competition in a production logistics scenario in the context of a Smart Factory. In the competition, a team of three robots needs to assemble products to fulfill various orders that are requested online during the game. This year, the Carologistics team was able to win the competition with a new approach to multi-agent coordination as well as significant changes to the robot’s perception unit and a pragmatic network setup using the cellular network instead of WiFi. In this paper, we describe the major components of our approach with a focus on the changes compared to the last physical competition in 2019. Y1 - 2023 SN - 978-3-031-28468-7 (Print) SN - 978-3-031-28469-4 (Online) U6 - https://doi.org/https://doi.org/10.1007/978-3-031-28469-4_25 N1 - Robot World Cup, RoboCup 2022. 17. July 2023. Bangkok, Thailand. Part of the Lecture Notes in Computer Science book series (LNAI,volume 13561) SP - 300 EP - 312 PB - Springer CY - Cham ER - TY - THES A1 - Glück, Anna T1 - Entwicklung eines Erscheinungsbildes für ein Unternehmen im Bereich Bioenergiefassaden N2 - Nachhaltige Technologien, die Ressourcen schonen und Energie gewinnen, erlangen zunehmend an Bedeutung im urbanen Raum. Diese Bachelorarbeit befasst sich mit der Entwicklung eines Corporate Designs für ein Unternehmen, das sich auf die Fertigung und Planung von Bioenergiefassaden spezialisiert hat. Das Unternehmen sorgt durch seinen Fokus auf nachhaltige Energiegewinnung und effiziente Gebäudeplanung für die Verbesserung der ökologischen Herausforderungen. Das Ziel des neuen Corporate Designs ist es, die komplexe Thematik der Bioenergiefassaden der Zielgruppe effektiv zu vermitteln und ihr Interesse für dieses System zu wecken. Dabei werden Illustrationen und Infografiken eingesetzt, um die Technologie verständlich darzustellen, die positiven Umweltauswirkungen sowie Vorteile der Bioenergiefassaden deutlich hervorzuheben und mehr Umsetzungen zu erzielen. KW - Bioenergiefassaden KW - Erscheinungsbild KW - Nachhaltigkeit KW - Technologie KW - Algen Y1 - 2023 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER - TY - CHAP A1 - Zähl, Philipp M. A1 - Theis, Sabine A1 - Wolf, Martin A1 - Köhler, Klemens ED - Chen, Jessie Y. C. ED - Fragomeni, Gino T1 - Teamwork in software development and what personality has to do with it - an overview T2 - Virtual, Augmented and Mixed Reality N2 - Due to the increasing complexity of software projects, software development is becoming more and more dependent on teams. The quality of this teamwork can vary depending on the team composition, as teams are always a combination of different skills and personality types. This paper aims to answer the question of how to describe a software development team and what influence the personality of the team members has on the team dynamics. For this purpose, a systematic literature review (n=48) and a literature search with the AI research assistant Elicit (n=20) were conducted. Result: A person’s personality significantly shapes his or her thinking and actions, which in turn influences his or her behavior in software development teams. It has been shown that team performance and satisfaction can be strongly influenced by personality. The quality of communication and the likelihood of conflict can also be attributed to personality. KW - Teamwork KW - Software KW - Personality KW - Performance KW - Elicit Y1 - 2023 SN - 978-3-031-35633-9 (Print) SN - 978-3-031-35634-6 (Online) U6 - https://doi.org/10.1007/978-3-031-35634-6_10 N1 - Virtual, Augmented and Mixed Reality: 15th International Conference. VAMR 2023. Held as Part of the 25th HCI International Conference. HCII 2023. Copenhagen, Denmark. July 23–28, 2023. SP - 130 EP - 153 PB - Springer CY - Cham ER - TY - CHAP A1 - Arndt, Tobias A1 - Conzen, Max A1 - Elsen, Ingo A1 - Ferrein, Alexander A1 - Galla, Oskar A1 - Köse, Hakan A1 - Schiffer, Stefan A1 - Tschesche, Matteo T1 - Anomaly detection in the metal-textile industry for the reduction of the cognitive load of quality control workers T2 - PETRA '23: Proceedings of the 16th International Conference on PErvasive Technologies Related to Assistive Environments N2 - This paper presents an approach for reducing the cognitive load for humans working in quality control (QC) for production processes that adhere to the 6σ -methodology. While 100% QC requires every part to be inspected, this task can be reduced when a human-in-the-loop QC process gets supported by an anomaly detection system that only presents those parts for manual inspection that have a significant likelihood of being defective. This approach shows good results when applied to image-based QC for metal textile products. KW - Datasets KW - Neural networks KW - Anomaly detection KW - Quality control KW - Process optimization Y1 - 2023 SN - 9798400700699 U6 - https://doi.org/10.1145/3594806.3596558 N1 - PETRA '23: Proceedings of the 16th International Conference on PErvasive Technologies Related to Assistive Environments, Corfu, Greece, July 5 - 7, 2023 SP - 535 EP - 542 PB - ACM ER - TY - JOUR A1 - Dellmann, Sophia Florence A1 - Glorius, J. A1 - Litvinov, Yu A. A1 - Reifarth, R. A1 - Al-Khasawneh, Kafa A1 - Aliotta, M. A1 - Bott, L. A1 - Brückner, Benjamin A1 - Bruno, C. G. A1 - Chen, Ruijiu A1 - Davinson, T. A1 - Dickel, T. A1 - Dillmann, Iris A1 - Dmytriev, D. A1 - Erbacher, P. A1 - Freire-Fernández, D. A1 - Forstner, Oliver A1 - Geissel, H. A1 - Göbel, K. A1 - Griffin, Christopher J. A1 - Grisenti, R. A1 - Gumberidze, Alexandre A1 - Haettner, Emma A1 - Hagmann, Siegbert A1 - Heil, M. A1 - Heß, R. A1 - Hillenbrand, P.-M. A1 - Joseph, R. A1 - Jurado, B. A1 - Kozhuharov, Christophor A1 - Kulikov, I. A1 - Löher, Bastian A1 - Langer, Christoph A1 - Leckenby, Guy A1 - Lederer-Woods, C. A1 - Lestinsky, M. A1 - Litvinov, S. A. A1 - Lorenz, B. A. A1 - Lorenz, E. A1 - Marsh, J. A1 - Menz, Esther Babette A1 - Morgenroth, T. A1 - Petridis, N. A1 - Pibernat, Jerome A1 - Popp, U. A1 - Psaltis, Athanasios A1 - Sanjari, Shahab A1 - Scheidenberger, C. A1 - Sguazzin, M. A1 - Sidhu, Ragandeep Singh A1 - Spillmann, Uwe A1 - Steck, M. A1 - Stöhlker, T. A1 - Surzhykov, A. A1 - Swartz, J. A. A1 - Törnqvist, H. A1 - Varga, L. A1 - Vescovi, Diego A1 - Weick, H. A1 - Weigand, M. A1 - Woods, P. A1 - Xing, Y. A1 - Yamaguchi, Taiyo T1 - Proton capture on stored radioactive ¹¹⁸Te ions JF - EPJ Web of Conferences N2 - Experimental determination of the cross sections of proton capture on radioactive nuclei is extremely difficult. Therefore, it is of substantial interest for the understanding of the production of the p-nuclei. For the first time, a direct measurement of proton-capture cross sections on stored, radioactive ions became possible in an energy range of interest for nuclear astrophysics. The experiment was performed at the Experimental Storage Ring (ESR) at GSI by making use of a sensitive method to measure (p,γ) and (p,n) reactions in inverse kinematics. These reaction channels are of high relevance for the nucleosyn-thesis processes in supernovae, which are among the most violent explosions in the universe and are not yet well understood. The cross section of the ¹¹⁸Te(p,γ) reaction has been measured at energies of 6 MeV/u and 7 MeV/u. The heavy ions interacted with a hydrogen gas jet target. The radiative recombination process of the fully stripped ¹¹⁸Te ions and electrons from the hydrogen target was used as a luminosity monitor. An overview of the experimental method and preliminary results from the ongoing analysis will be presented. Y1 - 2023 U6 - https://doi.org/10.1051/epjconf/202327911018 SN - 2100-014X N1 - Volume 279, 2023. Nuclear Physics in Astrophysics – X (NPA-X 2022). VL - 279 IS - Article Number: 11018 SP - 1 EP - 5 PB - EDP Sciences ER - TY - CHAP A1 - Neth, Jannik A1 - Schuba, Marko A1 - Brodkorb, Karsten A1 - Neugebauer, Georg A1 - Höner, Tim A1 - Hack, Sacha T1 - Digital forensics triage app for android T2 - ARES '23: Proceedings of the 18th International Conference on Availability, Reliability and Security N2 - Digital forensics of smartphones is of utmost importance in many criminal cases. As modern smartphones store chats, photos, videos etc. that can be relevant for investigations and as they can have storage capacities of hundreds of gigabytes, they are a primary target for forensic investigators. However, it is exactly this large amount of data that is causing problems: extracting and examining the data from multiple phones seized in the context of a case is taking more and more time. This bears the risk of wasting a lot of time with irrelevant phones while there is not enough time left to analyze a phone which is worth examination. Forensic triage can help in this case: Such a triage is a preselection step based on a subset of data and is performed before fully extracting all the data from the smartphone. Triage can accelerate subsequent investigations and is especially useful in cases where time is essential. The aim of this paper is to determine which and how much data from an Android smartphone can be made directly accessible to the forensic investigator – without tedious investigations. For this purpose, an app has been developed that can be used with extremely limited storage of data in the handset and which outputs the extracted data immediately to the forensic workstation in a human- and machine-readable format. KW - Android KW - Digital triage KW - Triage-app Y1 - 2023 SN - 9798400707728 U6 - https://doi.org/10.1145/3600160.3605017 N1 - ARES 2023: The 18th International Conference on Availability, Reliability and Security. August 29 - September 1, 2023. Benevento, Italy. PB - ACM ER - TY - JOUR A1 - Falkenberg, Fabian A1 - Kohn, Sophie A1 - Bott, Michael A1 - Bongaerts, Johannes A1 - Siegert, Petra T1 - Biochemical characterisation of a novel broad pH spectrum subtilisin from Fictibacillus arsenicus DSM 15822ᵀ JF - FEBS Open Bio N2 - Subtilisins from microbial sources, especially from the Bacillaceae family, are of particular interest for biotechnological applications and serve the currently growing enzyme market as efficient and novel biocatalysts. Biotechnological applications include use in detergents, cosmetics, leather processing, wastewater treatment and pharmaceuticals. To identify a possible candidate for the enzyme market, here we cloned the gene of the subtilisin SPFA from Fictibacillus arsenicus DSM 15822ᵀ (obtained through a data mining-based search) and expressed it in Bacillus subtilis DB104. After production and purification, the protease showed a molecular mass of 27.57 kDa and a pI of 5.8. SPFA displayed hydrolytic activity at a temperature optimum of 80 °C and a very broad pH optimum between 8.5 and 11.5, with high activity up to pH 12.5. SPFA displayed no NaCl dependence but a high NaCl tolerance, with decreasing activity up to concentrations of 5 m NaCl. The stability enhanced with increasing NaCl concentration. Based on its substrate preference for 10 synthetic peptide 4-nitroanilide substrates with three or four amino acids and its phylogenetic classification, SPFA can be assigned to the subgroup of true subtilisins. Moreover, SPFA exhibited high tolerance to 5% (w/v) SDS and 5% H₂O₂ (v/v). The biochemical properties of SPFA, especially its tolerance of remarkably high pH, SDS and H₂O₂, suggest it has potential for biotechnological applications. KW - Bacillaceae KW - Biotechnological application KW - Broad pH spectrum KW - Subtilases KW - Subtilisin Y1 - 2023 U6 - https://doi.org/10.1002/2211-5463.13701 SN - 2211-5463 N1 - Corresponding author: Petra Siegert VL - 13 IS - 11 SP - 2035 EP - 2046 PB - Wiley CY - Hoboken, NJ ER - TY - CHAP A1 - Schulze-Buxloh, Lina A1 - Groß, Rolf Fritz A1 - Ulbrich, Michelle T1 - Digital planning using building information modelling and virtual reality: new approach for students’ remote practical training under lockdown conditions in the course of smart building engineering T2 - Proceedings of International Conference on Education in Mathematics, Science and Technology 2021 N2 - The worldwide Corona pandemic has severely restricted student projects in the higher semesters of engineering courses. In order not to delay the graduation, a new concept had to be developed for projects under lockdown conditions. Therefore, unused rooms at the university should be digitally recorded in order to develop a new usage concept as laboratory rooms. An inventory of the actual state of the rooms was done first by taking photos and listing up all flaws and peculiarities. After that, a digital site measuring was done with a 360° laser scanner and these recorded scans were linked to a coherent point cloud and transferred to a software for planning technical building services and supporting Building Information Modelling (BIM). In order to better illustrate the difference between the actual and target state, two virtual reality models were created for realistic demonstration. During the project, the students had to go through the entire digital planning phases. Technical specifications had to be complied with, as well as documentation, time planning and cost estimate. This project turned out to be an excellent alternative to on-site practical training under lockdown conditions and increased the students’ motivation to deal with complex technical questions. KW - smart building engineering KW - building information modelling KW - virtual reality KW - lockdown conditions KW - emote practical training Y1 - 2021 SN - 978-1-952092-17-6 N1 - International Conference on Education in Mathematics, Science and Technology 2021, April 1-4, 2021 in Antalya, Turkey SP - 118 EP - 123 PB - ISTES Organization CY - San Antonio, TX ER - TY - CHAP A1 - Schulze-Buxloh, Lina A1 - Groß, Rolf Fritz T1 - Interdisciplinary Course Smart Building Engineering: A new approach of teaching freshmen in remote teamwork project under pandemic restrictions T2 - New Perspectives in Science Education - International Conference N2 - In the context of the Corona pandemic and its impact on teaching like digital lectures and exercises a new concept especially for freshmen in demanding courses of Smart Building Engineering became necessary. As there were hardly any face-to-face events at the university, the new teaching concept should enable a good start into engineering studies under pandemic conditions anyway and should also replace the written exam at the end. The students should become active themselves in small teams instead of listening passively to a lecture broadcast online with almost no personal contact. For this purpose, a role play was developed in which the freshmen had to work out a complete solution to the realistic problem of designing, construction planning and implementing a small guesthouse. Each student of the team had to take a certain role like architect, site manager, BIM-manager, electrician and the technitian for HVAC installations. Technical specifications must be complied with, as well as documentation, time planning and cost estimate. The final project folder had to contain technical documents like circuit diagrams for electrical components, circuit diagrams for water and heating, design calculations and components lists. On the other hand construction schedule, construction implementation plan, documentation of the construction progress and minutes of meetings between the various trades had to be submitted as well. In addition to the project folder, a model of the construction project must also be created either as a handmade model or as a digital 3D-model using Computer-aided design (CAD) software. The first steps in the field of Building information modelling (BIM) had also been taken by creating a digital model of the building showing the current planning status in real time as a digital twin. This project turned out to be an excellent training of important student competencies like teamwork, communication skills, and self -organisation and also increased motivation to work on complex technical questions. The aim of giving the student a first impression on the challenges and solutions in building projects with many different technical trades and their points of view was very well achieved and should be continued in the future. KW - Freshmen KW - roleplay KW - Smart Building Engineering KW - BIM KW - remote teamwork Y1 - 2021 N1 - New Perspectives in Science Education - 10th Edition, 18-19 March 2021, Fully Virtual Conference PB - Filodiritto CY - Bologna ER - TY - BOOK T1 - Baukeramik Y1 - 1925 N1 - Erscheinungsdatum circa 1925. Es fehlen die folgenden Seiten: 7, 12, 19, 23, 24, 27, 28, 31, ER - TY - THES A1 - Friedel, Janina T1 - Die Dinge danach : zum Hochwasser 21 N2 - Juli 2021. Durch starke Regenfälle von bis zu 250 l/m² innerhalb von 24h durch das Sturmtief «Bernd» war es dem bereits von vorherigen Niederschlägen übersättigten Boden nicht mehr möglich, weitere Wassermengen aufzunehmen. Die Folge sind schwerwiegende Überflutungen vor allem in Rheinland-Pfalz und NRW. Dass die Auswirkungen des Klimawandels bereits zu Hause angekommen sind, wird mit dieser Arbeit autobiografisch und illustrativ innerhalb eines Graphic Novels «Die Dinge danach – zum Hochwasser 21» be- und verarbeitet. Denn als das Wasser zu Hause wütete, war die Autorin selbst nicht anwesend. Dafür steckte sie die ersten Tage in Euskirchen fest, eine Stadt, die selbst Land unter war und zu einer Insel wurde. Ohne Strom, Netz und stark erschwertem Kontakt nach außen … und dabei sollte sie ursprünglich für eine Woche nur zwei Kater versorgen. KW - Illustration KW - Graphic Novel KW - Hochwasserkatastrophe KW - Juli21 KW - Flut Y1 - 2023 PB - FH Aachen CY - Aachen ER - TY - THES A1 - Doblas, Miguel T1 - Electrovisuals : Auditive Eigenschaften elektronischer Musik infografisch interpretiert N2 - Elektronische Musik umgibt uns alle. Der Einfluss elektronischer Musikproduktion auf moderne Popularmusik ist nicht von der Hand zu weisen und ihre Produktionstechniken für heutige Standards unverzichtbar. Über die Jahre ihrer Entwicklung und den dabei entstandenen Musikrichtungen verschwanden die individuellen Charakteristika der verschiedenen Subgenres allerdings oft einfach unter der Sammelbezeichnung elektronischer Musik. »Electrovisuals« stellt die auditiven Eigenschaften elektronischer Musik in Form von klaren Infografiken dar und sorgt damit für ein besseres Verständnis von Rhythmus und Struktur der Songs. Die verschiedenen Subgenres werden multimedial inszeniert und einander gegenübergestellt, um Ähnlichkeiten und Unterschiede zu betonen. Mithilfe seiner Aufbereitung stellt das Projekt die hohe Diversität elektronischer Musik heraus und bereitet sie eindrucksvoll und greifbar auf. KW - Musik KW - Datenvisualisierung KW - Informationsdesign KW - audiovisuell KW - interaktiv Y1 - 2023 PB - FH Aachen CY - Aachen ER - TY - THES A1 - Brügging, Justus Wilhelm T1 - Das Keramikmuseum KERAMION : Entwicklung eines neuen Erscheinungsbildes N2 - Das KERAMION beherbergt ein breites Sortiment an historischen Keramikstücken wie auch modernen künstlerischen Keramikarbeiten. Bei der neuen Konzeptionierung des Museums wurde eine Verbindung der historischen Sammlung und der modernen Kunst geschaffen, als Visualisierung dafür steht die eigens für das Museum erstellte Schrift. In dieser Schrift wird eine historische, schwungvolle Kurrentschrift aus dem 16. Jahrhundert mit einer modernen kantigen Serifenschrift verbunden. Daraus entsteht eine Schrift, die die Breite der Keramik widerspiegelt und von Steingut bis Porzellan alle Facetten aufgreift. Gepaart wird die einzigartige Schrift mit einem auf das Zentrum ausgerichteten Layoutprinzip, bei dem 3D Scans der Exponate in den Fokus rücken. Somit können die Besucher*innen auch von zu Hause einen Vorgeschmack auf die einzigartigen Materialien und Keramiktechniken bekommen. KW - Keramik KW - Museum KW - Typografie KW - Corporate Design KW - 3D Scan Y1 - 2023 PB - FH Aachen CY - Aachen ER - TY - THES A1 - Baumann, Ivana Edita T1 - Toolbar : Werkzeuge des Grafikdesigns N2 - Von Zeichentisch und Letraset zu inhaltsbasierter Füllung und OpenType – wie sich die Werkzeuge des Grafikdesigns entwickelt und die Gestaltungsprozesse beeinflusst haben. Die Bachelorarbeit „Toolbar: Werkzeuge des Grafikdesigns“ setzt sich mit der eigenen Disziplin, dem Grafikdesign, auseinander und geht dabei seinen Wurzeln, den Werkzeugen, nach. Im Rahmen dessen werden in Gesprächen mit verschiedenen Gestalter*innen Tools und Technologien des Grafikdesigns untersucht und verglichen – angefangen vom analogen Paste-Up bis hin zu modernen Designmethoden. Dabei wird diskutiert, wie sich die Werkzeuge im Laufe der Zeit entwickelt haben und welche Auswirkungen dies auf das Grafikdesign und die Positionierung von Designer*innen hatte. Außerdem wird die Bedeutung von Werkzeugen im kreativen Prozess und ihre Auswirkungen auf die Gestaltung hinterfragt und aufgezeigt. KW - Grafikdesign KW - Werkzeuge KW - Toolbar KW - Letraset KW - Rotring Y1 - 2023 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER - TY - THES A1 - Baierlein, Ellen T1 - Konzerthaus Berlin : Entwicklung eines Erscheinungsbildes für das Konzerthaus Berlin N2 - Das Konzerthaus Berlin ist einer der schönsten Orte Berlins für klassische Musik. Dabei steht das Haus auf der Schwelle zwischen langer Tradition und Moderne. Die Qualität an Musik, die dort gespielt wird, soll dabei für alle zugänglich sein. Dies machen die unterschiedlichsten Konzerte möglich. Um diesen modernen Anspruch auch nach außen zu kommunizieren, wurde ein neues Gestaltungskonzept für das Konzerthaus Berlin entwickelt. Im Fokus des neu entwickelten Corporate Designs steht der Rhythmus Gedanke, welcher sich im Headline Prinzip zeigt sowie medienübergreifend in der Layoutgestaltung durch Groß/Klein Kontraste fortsetzt. Das Erscheinungsbild funktioniert dabei sowohl animiert als auch statisch. Musik wird dadurch visuell erfahrbar gemacht und bildet den modernen Fokuspunkt in der Gestaltung. KW - Corporate Design KW - Konzerthaus KW - Klassische Musik KW - Musik KW - Berlin Y1 - 2023 PB - FH Aachen CY - Aachen ER - TY - THES A1 - Bähr, Luisa T1 - Localution : Entwicklung eines digitalen Lösungsmodells zur Verbindung des digitalen und stationären Handels N2 - Die Nutzung des Onlinehandels steigt seit Jahren kontinuierlich an. Für Händler:innen und ganz besonders für kleine Anbieter:innen, die zunehmend von größeren verdrängt werden, ist es wichtiger denn je, ihren Onlineauftritt auf den neuesten Stand zu bringen. Doch stellt dies die kleineren Anbieter:innen oftmals vor große Herausforderungen, denn der digitale Handel muss stets aktualisiert werden und kostet Zeit, Aufwand und Geld. „Localution“ ist eine digitale Plattform, die es lokalen Anbieter:innen möglich macht, mit wenig Aufwand eine Webseite aufzubauen. Zusätzlich sind Angebote buchbar, die den stationären Handel optimieren. Für Konsument:innen bietet „Localution“ die Möglichkeit, lokale Anbieter:innen in der Nähe zu finden und Termine zu buchen. KW - Onlinehandel KW - Lokal KW - Interaktive Gestaltung KW - Onlinepräsenz KW - Künstliche Intelligenz Y1 - 2023 PB - FH Aachen CY - Aachen ER - TY - THES A1 - Gaigall, Daniel T1 - On selected problems in multivariate analysis N2 - Selected problems in the field of multivariate statistical analysis are treated. Thereby, one focus is on the paired sample case. Among other things, statistical testing problems of marginal homogeneity are under consideration. In detail, properties of Hotelling‘s T² test in a special parametric situation are obtained. Moreover, the nonparametric problem of marginal homogeneity is discussed on the basis of possibly incomplete data. In the bivariate data case, properties of the Hoeffding-Blum-Kiefer-Rosenblatt independence test statistic on the basis of partly not identically distributed data are investigated. Similar testing problems are treated within the scope of the application of a result for the empirical process of the concomitants for partly categorial data. Furthermore, testing changes in the modeled solvency capital requirement of an insurance company by means of a paired sample from an internal risk model is discussed. Beyond the paired sample case, a new asymptotic relative efficiency concept based on the expected volumes of multidimensional confidence regions is introduced. Besides, a new approach for the treatment of the multi-sample goodness-of-fit problem is presented. Finally, a consistent test for the treatment of the goodness-of-fit problem is developed for the background of huge or infinite dimensional data. KW - Paired sample KW - Marginal homogeneity KW - Incomplete data KW - Asymptotic relative efficiency KW - Volumes of confidence regions Y1 - 2023 U6 - https://doi.org/10.15488/14304 N1 - Gottfried Wilhelm Leibniz Universität Hannover ER - TY - JOUR A1 - Fissabre, Anke A1 - Rottke, Evelin ED - Bergdoll, Barry ED - Schwarting, Andreas ED - Tragbar, Klaus T1 - Das Quelle-Fertighaus : Einklang von Maß, Konstruktion und Entwurf JF - architectura N2 - The steel prefabricated family house ›Quelle-Fertighaus‹ designed and constructed by the German company Quelle, is an innovative modular system commercialised in 1962. All aspects of the Quelle-Fertighaus are planned on the principle of minimal effort for maximal flexibility. The clever design of the ground plan based on a 4 m × 7 m module offers the flexibility for either one to three additional modules. The steel construction is innovative and unique, consisting of load-bearing portal frames acting as braces. The house design is furthermore characterised by a simple metrical grid layout and the practical placement of the foundation and basement, which allowed the very cost-effective production and the lowest price for a prefabricated family house in Germany during the postwar era. Nowadays its portal-frame-construction offers an interesting approach for its renovation and transformation according to present building demands. KW - Quelle-Fertighaus KW - Stahlkonstruktion KW - Portalrahmen KW - Modulbau KW - 60er Jahre Y1 - 2023 U6 - https://doi.org/10.1515/atc-2021-1005 SN - 2569-1554 VL - 51 IS - 1 SP - 57 EP - 78 PB - Deutscher Kunstverlag (DKV) CY - Berlin ER - TY - JOUR A1 - Cheenakula, Dheeraja A1 - Paulsen, Svea A1 - Ott, Fabian A1 - Grömping, Markus T1 - Operational window of a deammonifying sludge for mainstream application in a municipal wastewater treatment plant JF - Water and Environment Journal N2 - The present work aimed to study the mainstream feasibility of the deammonifying sludge of side stream of municipal wastewater treatment plant (MWWTP) in Kaster, Germany. For this purpose, the deammonifying sludge available at the side stream was investigated for nitrogen (N) removal with respect to the operational factors temperature (15–30°C), pH value (6.0–8.0) and chemical oxygen demand (COD)/N ratio (≤1.5–6.0). The highest and lowest N-removal rates of 0.13 and 0.045 kg/(m³ d) are achieved at 30 and 15°C, respectively. Different conditions of pH and COD/N ratios in the SBRs of Partial nitritation/anammox (PN/A) significantly influenced both the metabolic processes and associated N-removal rates. The scientific insights gained from the current work signifies the possibility of mainstream PN/A at WWTPs. The current study forms a solid basis of operational window for the upcoming semi-technical trails to be conducted prior to the full-scale mainstream PN/A at WWTP Kaster and WWTPs globally. KW - Anammox KW - Mainstream KW - Nitrogen removal KW - Partial nitritation KW - Wastewater Y1 - 2023 U6 - https://doi.org/10.1111/wej.12898 SN - 1747-6593 N1 - Corresponding author: Dheeraja Cheenakula VL - 38 IS - 1 SP - 59 EP - 70 PB - Wiley CY - Chichester ER - TY - CHAP A1 - Küppers, Malte A1 - Schuba, Marko A1 - Neugebauer, Georg A1 - Höner, Tim A1 - Hack, Sacha T1 - Security analysis of the KNX smart building protocol T2 - ARES '23: Proceedings of the 18th International Conference on Availability, Reliability and Security N2 - KNX is a protocol for smart building automation, e.g., for automated heating, air conditioning, or lighting. This paper analyses and evaluates state-of-the-art KNX devices from manufacturers Merten, Gira and Siemens with respect to security. On the one hand, it is investigated if publicly known vulnerabilities like insecure storage of passwords in software, unencrypted communication, or denialof-service attacks, can be reproduced in new devices. On the other hand, the security is analyzed in general, leading to the discovery of a previously unknown and high risk vulnerability related to so-called BCU (authentication) keys. Y1 - 2023 U6 - https://doi.org/10.1145/3600160.3605167 N1 - ARES 2023: The 18th International Conference on Availability, Reliability and Security. August 29 - September 1, 2023. Benevento, Italy. Article No.: 87 SP - 1 EP - 7 PB - ACM ER - TY - GEN A1 - Schulze-Buxloh, Lina A1 - Groß, Rolf Fritz A1 - Cheng, Kevin Toni T1 - Development and manufacturing of an interactive three-dimensional phase diagram of carbon dioxide for teaching sessions in thermodynamics T2 - Proceedings of the International Conference The Future of Education 2020 Y1 - 2020 ER - TY - CHAP A1 - Galdi, Chiara A1 - Hartung, Frank A1 - Dugelay, Jean-Luc T1 - Videos versus still images: Asymmetric sensor pattern noise comparison on mobile phones T2 - Electronic Imaging N2 - Nowadays, the most employed devices for recoding videos or capturing images are undoubtedly the smartphones. Our work investigates the application of source camera identification on mobile phones. We present a dataset entirely collected by mobile phones. The dataset contains both still images and videos collected by 67 different smartphones. Part of the images consists in photos of uniform backgrounds, especially collected for the computation of the RSPN. Identifying the source camera given a video is particularly challenging due to the strong video compression. The experiments reported in this paper, show the large variation in performance when testing an highly accurate technique on still images and videos. KW - Image Forensics KW - Mobile Phones KW - Image Database Y1 - 2017 U6 - https://doi.org/10.2352/ISSN.2470-1173.2017.7.MWSF-331 SN - 2470-1173 N1 - IS&T International Symposium on Electronic Imaging 2017 Media Watermarking, Security, and Forensics 2017 SP - 100 EP - 103 PB - Society for Imaging Science and Technology CY - Springfield, Virginia ER - TY - JOUR A1 - Thoma, Andreas A1 - Thomessen, Karolin A1 - Gardi, Alessandro A1 - Fisher, A. A1 - Braun, Carsten T1 - Prioritising paths: An improved cost function for local path planning for UAV in medical applications JF - The Aeronautical Journal N2 - Even the shortest flight through unknown, cluttered environments requires reliable local path planning algorithms to avoid unforeseen obstacles. The algorithm must evaluate alternative flight paths and identify the best path if an obstacle blocks its way. Commonly, weighted sums are used here. This work shows that weighted Chebyshev distances and factorial achievement scalarising functions are suitable alternatives to weighted sums if combined with the 3DVFH* local path planning algorithm. Both methods considerably reduce the failure probability of simulated flights in various environments. The standard 3DVFH* uses a weighted sum and has a failure probability of 50% in the test environments. A factorial achievement scalarising function, which minimises the worst combination of two out of four objective functions, reaches a failure probability of 26%; A weighted Chebyshev distance, which optimises the worst objective, has a failure probability of 30%. These results show promise for further enhancements and to support broader applicability. KW - Path planning KW - Cost function KW - Multi-objective optimization Y1 - 2023 U6 - https://doi.org/10.1017/aer.2023.68 SN - 0001-9240 (Print) SN - 2059-6464 (Online) IS - First View SP - 1 EP - 18 PB - Cambridge University Press CY - Cambridge ER - TY - CHAP A1 - Dachwald, Bernd A1 - Ulamec, Stephan A1 - Kowalski, Julia A1 - Boxberg, Marc S. A1 - Baader, Fabian A1 - Biele, Jens A1 - Kömle, Norbert ED - Badescu, Viorel ED - Zacny, Kris ED - Bar-Cohen, Yoseph T1 - Ice melting probes T2 - Handbook of Space Resources N2 - The exploration of icy environments in the solar system, such as the poles of Mars and the icy moons (a.k.a. ocean worlds), is a key aspect for understanding their astrobiological potential as well as for extraterrestrial resource inspection. On these worlds, ice melting probes are considered to be well suited for the robotic clean execution of such missions. In this chapter, we describe ice melting probes and their applications, the physics of ice melting and how the melting behavior can be modeled and simulated numerically, the challenges for ice melting, and the required key technologies to deal with those challenges. We also give an overview of existing ice melting probes and report some results and lessons learned from laboratory and field tests. KW - Ice melting probe KW - Ice penetration KW - Icy moons KW - Ocean worlds KW - Mars Y1 - 2023 SN - 978-3-030-97912-6 (Print) SN - 978-3-030-97913-3 (Online) U6 - https://doi.org/10.1007/978-3-030-97913-3_29 SP - 955 EP - 996 PB - Springer CY - Cham ER - TY - JOUR A1 - Morais, Paulo V. A1 - Suman, Pedro H. A1 - Schöning, Michael Josef A1 - Siqueira Junior, José R. A1 - Orlandi, Marcelo O. T1 - Layer-by-layer film based on Sn₃O₄ nanobelts as sensing units to detect heavy metals using a capacitive field-effect sensor platform JF - Chemosensors N2 - Lead and nickel, as heavy metals, are still used in industrial processes, and are classified as “environmental health hazards” due to their toxicity and polluting potential. The detection of heavy metals can prevent environmental pollution at toxic levels that are critical to human health. In this sense, the electrolyte–insulator–semiconductor (EIS) field-effect sensor is an attractive sensing platform concerning the fabrication of reusable and robust sensors to detect such substances. This study is aimed to fabricate a sensing unit on an EIS device based on Sn₃O₄ nanobelts embedded in a polyelectrolyte matrix of polyvinylpyrrolidone (PVP) and polyacrylic acid (PAA) using the layer-by-layer (LbL) technique. The EIS-Sn₃O₄ sensor exhibited enhanced electrochemical performance for detecting Pb²⁺ and Ni²⁺ ions, revealing a higher affinity for Pb²⁺ ions, with sensitivities of ca. 25.8 mV/decade and 2.4 mV/decade, respectively. Such results indicate that Sn₃O₄ nanobelts can contemplate a feasible proof-of-concept capacitive field-effect sensor for heavy metal detection, envisaging other future studies focusing on environmental monitoring. KW - Sn₃O₄ KW - nanobelts KW - field-effect sensor KW - LbL films KW - heavy metals Y1 - 2023 U6 - https://doi.org/10.3390/chemosensors11080436 SN - 2227-9040 N1 - This article belongs to the Special Issue The Application of Electrochemical Sensors or Biosensors Based on Nanomaterials VL - 11 IS - 8 PB - MDPI CY - Basel ER - TY - JOUR A1 - Hoffstadt, Kevin A1 - Cheenakula, Dheeraja A1 - Nikolausz, Marcell A1 - Krafft, Simone A1 - Harms, Hauke A1 - Kuperjans, Isabel T1 - Design and construction of a new reactor for flexible biomethanation of hydrogen JF - Fermentation N2 - The increasing share of renewable electricity in the grid drives the need for sufficient storage capacity. Especially for seasonal storage, power-to-gas can be a promising approach. Biologically produced methane from hydrogen produced from surplus electricity can be used to substitute natural gas in the existing infrastructure. Current reactor types are not or are poorly optimized for flexible methanation. Therefore, this work proposes a new reactor type with a plug flow reactor (PFR) design. Simulations in COMSOL Multiphysics ® showed promising properties for operation in laminar flow. An experiment was conducted to support the simulation results and to determine the gas fraction of the novel reactor, which was measured to be 29%. Based on these simulations and experimental results, the reactor was constructed as a 14 m long, 50 mm diameter tube with a meandering orientation. Data processing was established, and a step experiment was performed. In addition, a kLa of 1 h−1 was determined. The results revealed that the experimental outcomes of the type of flow and gas fractions are in line with the theoretical simulation. The new design shows promising properties for flexible methanation and will be tested. KW - methanation KW - plug flow reactor KW - bubble column KW - bio-methane KW - power-to-gas Y1 - 2023 U6 - https://doi.org/10.3390/fermentation9080774 SN - 2311-5637 N1 - The article belongs to the Special Issue Fermentation Processes: Modeling, Optimization and Control VL - 9 IS - 8 SP - 1 EP - 16 PB - MDPI CY - Basel ER - TY - JOUR A1 - Coll-Perales, Baldomero A1 - Schulte-Tigges, Joschua A1 - Rondinone, Michele A1 - Gozalvez, Javier A1 - Reke, Michael A1 - Matheis, Dominik A1 - Walter, Thomas T1 - Prototyping and evaluation of infrastructure-assisted transition of control for cooperative automated vehicles JF - IEEE Transactions on Intelligent Transportation Systems N2 - Automated driving is now possible in diverse road and traffic conditions. However, there are still situations that automated vehicles cannot handle safely and efficiently. In this case, a Transition of Control (ToC) is necessary so that the driver takes control of the driving. Executing a ToC requires the driver to get full situation awareness of the driving environment. If the driver fails to get back the control in a limited time, a Minimum Risk Maneuver (MRM) is executed to bring the vehicle into a safe state (e.g., decelerating to full stop). The execution of ToCs requires some time and can cause traffic disruption and safety risks that increase if several vehicles execute ToCs/MRMs at similar times and in the same area. This study proposes to use novel C-ITS traffic management measures where the infrastructure exploits V2X communications to assist Connected and Automated Vehicles (CAVs) in the execution of ToCs. The infrastructure can suggest a spatial distribution of ToCs, and inform vehicles of the locations where they could execute a safe stop in case of MRM. This paper reports the first field operational tests that validate the feasibility and quantify the benefits of the proposed infrastructure-assisted ToC and MRM management. The paper also presents the CAV and roadside infrastructure prototypes implemented and used in the trials. The conducted field trials demonstrate that infrastructure-assisted traffic management solutions can reduce safety risks and traffic disruptions. KW - Automated driving KW - automated vehicles KW - connected automated vehicles KW - CAV KW - experimental evaluation Y1 - 2021 U6 - https://doi.org/10.1109/TITS.2021.3061085 SN - 1524-9050 (Print) SN - 1558-0016 (Online) VL - 23 IS - 7 SP - 6720 EP - 6736 PB - IEEE ER - TY - CHAP A1 - Schulte-Tigges, Joschua A1 - Matheis, Dominik A1 - Reke, Michael A1 - Walter, Thomas A1 - Kaszner, Daniel ED - Krömker, Heidi T1 - Demonstrating a V2X enabled system for transition of control and minimum risk manoeuvre when leaving the operational design domain T2 - HCII 2023: HCI in Mobility, Transport, and Automotive Systems N2 - Modern implementations of driver assistance systems are evolving from a pure driver assistance to a independently acting automation system. Still these systems are not covering the full vehicle usage range, also called operational design domain, which require the human driver as fall-back mechanism. Transition of control and potential minimum risk manoeuvres are currently research topics and will bridge the gap until full autonomous vehicles are available. The authors showed in a demonstration that the transition of control mechanisms can be further improved by usage of communication technology. Receiving the incident type and position information by usage of standardised vehicle to everything (V2X) messages can improve the driver safety and comfort level. The connected and automated vehicle’s software framework can take this information to plan areas where the driver should take back control by initiating a transition of control which can be followed by a minimum risk manoeuvre in case of an unresponsive driver. This transition of control has been implemented in a test vehicle and was presented to the public during the IEEE IV2022 (IEEE Intelligent Vehicle Symposium) in Aachen, Germany. KW - V2X KW - Transiton of Control KW - Minimum Risk Manoeuvre KW - Operational Design Domain KW - Connected Automated Vehicle Y1 - 2023 SN - 978-3-031-35677-3 (Print) SN - 978-3-031-35678-0 (Online) U6 - https://doi.org/10.1007/978-3-031-35678-0_12 N1 - 5th International Conference, MobiTAS 2023, Held as Part of the 25th HCI International Conference, HCII 2023, Copenhagen, Denmark, July 23–28, 2023. SP - 200 EP - 210 PB - Springer CY - Cham ER - TY - CHAP A1 - Eggert, Mathias A1 - Moulen, Tobias ED - D'Onofrio, Sara ED - Meinhardt, Stefan T1 - Auswahl von Geschäftsprozessen zur Anwendung von Robotic Process Automation – Vergleich relevanter Kriterien aus Theorie und Praxis T2 - Robotik in der Wirtschaftsinformatik N2 - Die Auswahl der passenden Geschäftsprozesse für eine Automatisierung mittels Robotic Process Automation (RPA) ist für den Erfolg von RPA-Projekten entscheidend. Das vorliegende Kapitel liefert dafür Selektionskriterien, die aus einer qualitativen Studie mit elf interviewten RPA-Experten aus dem Versicherungsumfeld resultieren. Das Ergebnis umfasst eine gewichtete Liste von sieben Dimensionen und 51 Prozesskriterien, welche die Automatisierung mit Softwarerobotern begünstigen beziehungsweise deren Nichterfüllung eine Umsetzung erschweren oder sogar verhindern. Die drei wichtigsten Kriterien zur Auswahl von Geschäftsprozessen für die Automatisierung mittels RPA umfassen die Entlastung der an dem Prozess mitwirkenden Mitarbeiter (Arbeitnehmerentlastung), die Ausführbarkeit des Prozesses mittels Regeln (Regelbasierte Prozessteuerung) sowie ein positiver Kosten-Nutzen-Vergleich. Auf diesen Ergebnissen aufbauend wird ein Vergleich mit den bereits bekannten Selektionskriterien aus der Literatur erstellt und diskutiert. Praktiker können die Ergebnisse verwenden, um eine systematische Auswahl von RPA-relevanten Prozessen vorzunehmen. Aus wissenschaftlicher Perspektive stellen die Ergebnisse eine Grundlage zur Erklärung des Erfolgs und Misserfolgs von RPA-Projekten dar. KW - Experteninterviews KW - Prozessauswahl KW - Selektionskriterien KW - Prozessverbesserung KW - Prozessautomatisierung KW - Robotic Process Automation Y1 - 2023 SN - 978-3-658-39620-6 (Print) SN - 978-3-658-39621-3 (Online) N1 - Vollständig überarbeiteter und erweiterter Beitrag basierend auf Eggert M, Moulen T (2020) Selektion von Geschäftsprozessen zur Anwendung von Robotic Process Automation am Beispiel einer Versicherung, 57(5):1150–1162 SP - 107 EP - 129 PB - Springer Vieweg CY - Wiesbaden ER - TY - JOUR A1 - Grajewski, Matthias A1 - Kleefeld, Andreas T1 - Detecting and approximating decision boundaries in low-dimensional spaces JF - Numerical Algorithms N2 - A method for detecting and approximating fault lines or surfaces, respectively, or decision curves in two and three dimensions with guaranteed accuracy is presented. Reformulated as a classification problem, our method starts from a set of scattered points along with the corresponding classification algorithm to construct a representation of a decision curve by points with prescribed maximal distance to the true decision curve. Hereby, our algorithm ensures that the representing point set covers the decision curve in its entire extent and features local refinement based on the geometric properties of the decision curve. We demonstrate applications of our method to problems related to the detection of faults, to multi-criteria decision aid and, in combination with Kirsch’s factorization method, to solving an inverse acoustic scattering problem. In all applications we considered in this work, our method requires significantly less pointwise classifications than previously employed algorithms. KW - MCDA KW - Inverse scattering problem KW - Fault approximation KW - Fault detection Y1 - 2023 SN - 1572-9265 N1 - Corresponding author: Matthias Grajewski VL - 93 IS - 4 PB - Springer Science+Business Media CY - Dordrecht ER - TY - JOUR A1 - Cheenakula, Dheeraja A1 - Griebel, Kai A1 - Montag, David A1 - Grömping, Markus ED - Huang, Xiaowu T1 - Concept development of a mainstream deammonification and comparison with conventional process in terms of energy, performance and economical construction perspectives JF - Frontiers in Microbiology N2 - Deammonification for nitrogen removal in municipal wastewater in temperate and cold climate zones is currently limited to the side stream of municipal wastewater treatment plants (MWWTP). This study developed a conceptual model of a mainstream deammonification plant, designed for 30,000 P.E., considering possible solutions corresponding to the challenging mainstream conditions in Germany. In addition, the energy-saving potential, nitrogen elimination performance and construction-related costs of mainstream deammonification were compared to a conventional plant model, having a single-stage activated sludge process with upstream denitrification. The results revealed that an additional treatment step by combining chemical precipitation and ultra-fine screening is advantageous prior the mainstream deammonification. Hereby chemical oxygen demand (COD) can be reduced by 80% so that the COD:N ratio can be reduced from 12 to 2.5. Laboratory experiments testing mainstream conditions of temperature (8–20°C), pH (6–9) and COD:N ratio (1–6) showed an achievable volumetric nitrogen removal rate (VNRR) of at least 50 gN/(m3∙d) for various deammonifying sludges from side stream deammonification systems in the state of North Rhine-Westphalia, Germany, where m3 denotes reactor volume. Assuming a retained Norganic content of 0.0035 kgNorg./(P.E.∙d) from the daily loads of N at carbon removal stage and a VNRR of 50 gN/(m3∙d) under mainstream conditions, a resident-specific reactor volume of 0.115 m3/(P.E.) is required for mainstream deammonification. This is in the same order of magnitude as the conventional activated sludge process, i.e., 0.173 m3/(P.E.) for an MWWTP of size class of 4. The conventional plant model yielded a total specific electricity demand of 35 kWh/(P.E.∙a) for the operation of the whole MWWTP and an energy recovery potential of 15.8 kWh/(P.E.∙a) through anaerobic digestion. In contrast, the developed mainstream deammonification model plant would require only a 21.5 kWh/(P.E.∙a) energy demand and result in 24 kWh/(P.E.∙a) energy recovery potential, enabling the mainstream deammonification model plant to be self-sufficient. The retrofitting costs for the implementation of mainstream deammonification in existing conventional MWWTPs are nearly negligible as the existing units like activated sludge reactors, aerators and monitoring technology are reusable. However, the mainstream deammonification must meet the performance requirement of VNRR of about 50 gN/(m3∙d) in this case. KW - anammox KW - energy efficiency KW - mainstream deammonification KW - nitrogen elimination KW - wastewater Y1 - 2023 U6 - https://doi.org/10.3389/fmicb.2023.1155235 SN - 1664-302X VL - 14 IS - 11155235 SP - 1 EP - 15 PB - Frontiers ER - TY - JOUR A1 - Trapp, Svenja A1 - Lammers, Tom A1 - Engudar, Gokce A1 - Hoehr, Cornelia A1 - Denkova, Antonia G. A1 - Paulßen, Elisabeth A1 - de Kruijff, Robin M. T1 - Membrane-based microfluidic solvent extraction of Ga-68 from aqueous Zn solutions: towards an automated cyclotron production loop JF - EJNMMI Radiopharmacy and Chemistry KW - Microfluidic solvent extraction KW - Ga-68 KW - Cyclotron production KW - Medical radionuclide production KW - Metal contaminants Y1 - 2023 U6 - https://doi.org/10.1186/s41181-023-00195-2 SN - 2365-421X VL - 2023 IS - 8, Article number: 9 SP - 1 EP - 14 PB - Springer Nature ER - TY - CHAP A1 - Ulmer, Jessica A1 - Braun, Sebastian A1 - Wollert, Jörg T1 - Adaptive VR-Produktionsumgebungen für Evaluations- und Schulungstätigkeiten T1 - Adaptive VR production environments for evaluation and training purposes T2 - Automation 2021: Navigating towards resilient Production N2 - Industrie 4.0 stellt viele Herausforderungen an produzierende Unternehmen und ihre Beschäf-tigten. Innovative und effektive Trainingsstrategien sind erforderlich, um mit den sich schnell verändernden Produktionsumgebungen und neuen Fertigungstechnologien Schritt halten zu können. Virtual Reality (VR) bietet neue Möglichkeiten für On-the-Job, On-Demand- und Off-Premise-Schulungen. Diese Arbeit stellt ein neues VR Schulungssystem vor, welches sich flexible an unterschiedliche Trainingsobjekte auf Grundlage von Rezepten und CAD Modellen anpassen lässt. Das Konzept basiert auf gerichteten azyklischen Graphen und einem Level-system. Es ermöglicht eine benutzerindividuelle Lerngeschwindigkeit mittels visueller Ele-mente. Das Konzept wurde für einen mechanischen Anwendungsfall mit Industriekomponen-ten implementiert und in der Industrie 4.0-Modellfabrik der FH Aachen umgesetzt. N2 - Industry 4.0 poses many challenges for manufacturing companies and their employees. Inno-vative and effective training strategies are needed to keep pace with rapidly changing produc-tion environments and new manufacturing technologies. Virtual reality (VR) offers new oppor-tunities for on-the-job, on-demand, and off-premise training. This work presents a new VR training system that can be flexibly adapted to different training objects based on recipes and CAD models. The concept is based on directed acyclic graphs and a level system. It allows a user-individual learning speed by means of visual elements. The concept was implemented for a mechanical use case with industrial components and implemented in the industry 4.0 model factory of the FH Aachen University of Applied Sciences. Y1 - 2021 SN - 978-3-18-092392-5 U6 - https://doi.org/10.51202/9783181023921-55 SN - 0083-5560 N1 - 22. Leitkongress der Mess- und Automatisierungstechnik AUTOMATION 2021 - Navigating towards resilient Production, 29. und 30. Juni 2021 SP - 55 EP - 64 PB - VDI CY - Düsseldorf ER - TY - CHAP A1 - Ulmer, Jessica A1 - Mostafa, Youssef A1 - Wollert, Jörg T1 - Digital Twin Academy: From Zero to Hero through individual learning experiences T2 - Tagungsband AALE 2022: Wissenstransfer im Spannungsfeld von Autonomisierung und Fachkräftemangel N2 - Digital twins are seen as one of the key technologies of Industry 4.0. Although many research groups focus on digital twins and create meaningful outputs, the technology has not yet reached a broad application in the industry. The main reasons for this imbalance are the complexity of the topic, the lack of specialists, and the unawareness of the twin opportunities. The project "Digital Twin Academy" aims to overcome these barriers by focusing on three actions: Building a digital twin community for discussion and exchange, offering multi-stage training for various knowledge levels, and implementing realworld use cases for deeper insights and guidance. In this work, we focus on creating a flexible learning platform that allows the user to select a training path adjusted to personal knowledge and needs. Therefore, a mix of basic and advanced modules is created and expanded by individual feedback options. The usage of personas supports the selection of the appropriate modules. KW - Digital Twins KW - Knowledge Transfer KW - Training Y1 - 2022 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bsz:l189-qucosa2-776097 SN - 978-3-910103-00-9 N1 - 18. AALE-Konferenz. Pforzheim, 09.03.-11.03.2022 SP - 1 EP - 9 ER - TY - CHAP A1 - Chavez Bermudez, Victor Francisco A1 - Cruz Castanon, Victor Fernando A1 - Ruchay, Marco A1 - Wollert, Jörg ED - Leipzig, Hochschule für Technik, Wirtschaft und Kultur T1 - Rapid prototyping framework for automation applications based on IO-Link T2 - Tagungsband AALE 2022: Wissenstransfer im Spannungsfeld von Autonomisierung und Fachkräftemangel N2 - The development of protype applications with sensors and actuators in the automation industry requires tools that are independent of manufacturer, and are flexible enough to be modified or extended for any specific requirements. Currently, developing prototypes with industrial sensors and actuators is not straightforward. First of all, the exchange of information depends on the industrial protocol that these devices have. Second, a specific configuration and installation is done based on the hardware that is used, such as automation controllers or industrial gateways. This means that the development for a specific industrial protocol, highly depends on the hardware and the software that vendors provide. In this work we propose a rapid-prototyping framework based on Arduino to solve this problem. For this project we have focused to work with the IO-Link protocol. The framework consists of an Arduino shield that acts as the physical layer, and a software that implements the IO-Link Master protocol. The main advantage of such framework is that an application with industrial devices can be rapid-prototyped with ease as its vendor independent, open-source and can be ported easily to other Arduino compatible boards. In comparison, a typical approach requires proprietary hardware, is not easy to port to another system and is closed-source. KW - Rapid-prototyping KW - Arduino KW - IO-Link KW - Industrial Communication Y1 - 2022 SN - 978-3-910103-00-9 U6 - https://doi.org/10.33968/2022.28 N1 - 18. AALE-Konferenz. Pforzheim, 09.03.-11.03.2022 CY - Leipzig ER - TY - JOUR A1 - Cheng, Chi-Tsun A1 - Wollert, Jörg A1 - Chen, Xi A1 - Fapojuwo, Abraham O. T1 - Guest Editorial : Circuits and Systems for Industry X.0 Applications JF - IEEE Journal on Emerging and Selected Topics in Circuits and Systems Y1 - 2023 U6 - https://doi.org/10.1109/JETCAS.2023.3278843 SN - 2156-3357 (Print) SN - 2156-3365 (Online) VL - 13 SP - 457 EP - 460 PB - IEEE CY - New York ET - 2 ER - TY - JOUR A1 - Kuchler, Timon A1 - Günthner, Roman A1 - Ribeiro, Andrea A1 - Hausinger, Renate A1 - Streese, Lukas A1 - Wöhnl, Anna A1 - Kesseler, Veronika A1 - Negele, Johanna A1 - Assali, Tarek A1 - Carbajo-Lozoya, Javier A1 - Lech, Maciej A1 - Adorjan, Kristina A1 - Stubbe, Hans Christian A1 - Hanssen, Henner A1 - Kotliar, Konstantin A1 - Haller, Berhard A1 - Heemann, Uwe A1 - Schmaderer, Christoph T1 - Persistent endothelial dysfunction in post-COVID-19 syndrome and its associations with symptom severity and chronic inflammation N2 - Background Post-COVID-19 syndrome (PCS) is a lingering disease with ongoing symptoms such as fatigue and cognitive impairment resulting in a high impact on the daily life of patients. Understanding the pathophysiology of PCS is a public health priority, as it still poses a diagnostic and treatment challenge for physicians. Methods In this prospective observational cohort study, we analyzed the retinal microcirculation using Retinal Vessel Analysis (RVA) in a cohort of patients with PCS and compared it to an age- and gender-matched healthy cohort (n = 41, matched out of n = 204). Measurements and main results PCS patients exhibit persistent endothelial dysfunction (ED), as indicated by significantly lower venular flicker-induced dilation (vFID; 3.42% ± 1.77% vs. 4.64% ± 2.59%; p = 0.02), narrower central retinal artery equivalent (CRAE; 178.1 [167.5–190.2] vs. 189.1 [179.4–197.2], p = 0.01) and lower arteriolar-venular ratio (AVR; (0.84 [0.8–0.9] vs. 0.88 [0.8–0.9], p = 0.007). When combining AVR and vFID, predicted scores reached good ability to discriminate groups (area under the curve: 0.75). Higher PCS severity scores correlated with lower AVR (R = − 0.37 p = 0.017). The association of microvascular changes with PCS severity were amplified in PCS patients exhibiting higher levels of inflammatory parameters. Conclusion Our results demonstrate that prolonged endothelial dysfunction is a hallmark of PCS, and impairments of the microcirculation seem to explain ongoing symptoms in patients. As potential therapies for PCS emerge, RVA parameters may become relevant as clinical biomarkers for diagnosis and therapy management. KW - Endothelial dysfunction KW - Long COVID KW - Post-COVID-19 syndrome KW - retinal microvasculature Y1 - 2023 U6 - https://doi.org/10.1007/s10456-023-09885-6 N1 - Corresponding author: Christoph Schmaderer VL - 26 SP - 547 EP - 563 PB - Springer Nature CY - Dordrecht ER - TY - INPR A1 - Greiner, Lasse A1 - Jeromin, Günter Erich A1 - Sithole, Patience A1 - Petersen, Soenke T1 - Preprint: Studies on the enzymatic reduction of levulinic acid using Chiralidon-R and Chiralidon-S T2 - ChemRxiv N2 - The enzymatic reduction of levulinic acid by the chiral catalysts Chiralidon-R and Chiralidon-S which are commercially available superabsorbed alcohol dehydrogenases is described. The Chiralidon®-R/S reduces the levulinic acid to the (R,S)-4-hydroxy valeric acid and the (R)- or (S)- gamma-valerolactone. KW - Levulinic acid KW - Chiralidon-R KW - Chiralidon-S KW - 4-hydroxy valeric acid KW - (R)- or (S)- gamma-valerolactone Y1 - 2023 U6 - https://doi.org/10.26434/chemrxiv-2023-jlvcv ER - TY - JOUR A1 - Ohrtmann, Jan-Peter A1 - Golland, Alexander T1 - Datenschutz & Datenrecht – ein Ausblick auf 2023: Gesetzgebungsverfahren auf EU-Ebene JF - DSB Datenschutz-Berater N2 - Die Verfasser stellen in ihrem Beitrag die künftig in Kraft tretenden oder schon in Kraft getretenen Gesetzesvorhaben der europäischen Union vor. Vorab werde auf die abgelaufene Frist zur Anpassung von Standardvertragsklausel hingewiesen. Die Anpassung könne ggf. durch den Data Privacy Act der Kommission bewirkt werden, da dieser eine Angemessenheit suggeriere. Neben dem Digital Markets Act, der die Wahrung der Diskriminierungsfreiheit den Gatekeeper-Plattformen bezüglich der Bewerbung von Waren Dritter vorschreibt, sind ebenfalls der Digital Service Act und der Data Governance Act in Kraft getreten und werden künftig wirksam. Letzteres bezweckt den Datenaustausch von nicht-personenbezogenen Daten öffentlich-rechtlicher Datensätze, wobei anders als bei DSA, der die Verbraucherrechte durchsetzen möchte, mangels Verpflichtung die praktische Umsetzung ausbleiben werde. In der Entwurfsphase stecken der Artificial Intelligence Act, der Data Act, sowie der Cyber Resilience Act. Allen drei sei wegen dem weiten Anwendungsspielraum, der Bußgeldandrohung oder der Cyber-Bedrohungslage besondere praktische Relevanz beizumessen. Die Kommission weite durch diese Gesetzesvorhaben ihre Regelungsabsicht auch auf nicht-personenbezogene Daten und dem Datentransfer aus. Im Ergebnis werden die Unternehmen mit mehr Verpflichtungen konfrontiert, zu dessen Umsetzung ein funktionierendes Compliance-Management-System unabdingbar sei. Y1 - 2023 VL - 2023 IS - 2 SP - 43 EP - 46 PB - Fachmedien Recht und Wirtschaft CY - Frankfurt am Main ER - TY - JOUR A1 - Ohrtmann, Jan-Peter A1 - Golland, Alexander T1 - Datenschutz & Datenrecht – ein Ausblick auf 2023: Nationale Entwicklungen, EuGH-Vorlagen & Aufsicht JF - DSB Datenschutz-Berater N2 - Die Verfasser vermitteln einen Überblick über die nationalen Gesetzgebungsverfahren und wesentliche EuGH-Vorlagefragen betreffend den Datenschutz und das Datenrecht für das Jahr 2023. Zunächst folgen u.a. Hinweise in Bezug auf den Hinweisgeberschutz, die Verabschiedung der Einwilligungsverwaltungs-Verordnung zur Konkretisierung des § 26 TTDSG und das Mobilitätsdatengesetz. Anschließend werden Vorlagefragen deutscher Gerichte, die dem EuGH vorgelegt und bereits am 12.01.2023 beantwortet wurden, wie etwa C-154/21 und C-132/21 und die EuGH-Entscheidung vom 9.2.2023 (C-453/21), thematisiert. Überdies führen die Autoren wesentliche Entscheidungen des EuGH an, die im Jahr 2023 aus dem Bereich Datenrecht und Datenschutz zu erwarten seien. Auch Aktivitäten der Datenschutzaufsicht auf nationaler und europäischer Ebene finden Erwähnung. Die Verfasser machen abschließend auf besonders interessante Entscheidungen, die 2023 erwartet werden, wie etwa das EuGH-Urteil zum Auskunftsanspruch, sowie auf das Verhältnis des der Whistleblowing-RL umzusetzende Hinweisgeberschutzgesetz einerseits und Vorgaben des Datenschutzes andererseits, aufmerksam. Sie empfehlen, die künftige Rechtsprechung des EuGH im Blick zu behalten. Y1 - 2023 VL - 2023 IS - 3 SP - 73 EP - 75 PB - DFV Mediengruppe CY - Frankfurt a.M. ER - TY - GEN A1 - Golland, Alexander T1 - Formelle DSGVO-Verstöße wirken sich nicht auf Rechtmäßigkeit der Verarbeitung aus BT - Zugleich Besprechung einer Entscheidung des EuGH, Urteil vom 4.5.2023 - C-60/22 T2 - DSB Datenschutz-Berater N2 - In dem vorliegenden Beitrag setzt sich der Verfasser mit dem Urteil des EuGH vom 4.5.2023 (Az.: C-60/22, DSB 2023, 178) zu den Auswirkungen eines formellen Verstoßes des Verantwortlichen gegen die Pflichten aus Artt. 26, 30 DSGVO (juris: EUV 2016/679) auf die Rechtmäßigkeit der Datenverarbeitung auseinander. Nachdem zunächst der zugrunde liegende Sachverhalt und der Hintergrund des Vorlageverfahrens skizziert wurden, gibt der Verfasser einen Überblick über die wesentlichen Entscheidungsgründe des EuGH. Insbesondere stelle der EuGH hier fest, dass die Rechtmäßigkeit der Verarbeitung in Art. 6 DSGVO geregelt sei und sich eine rechtswidrige Verarbeitung daher nur aus einem Verstoß gegen die Artt. 6 ff. DSGVO ergeben könne; die Pflichten aus Art. 26 und Art. 30 DSGVO würden nicht zu den Gründen für die Rechtmäßigkeit der Verarbeitung zählen. Mit Blick auf die Praxis lasse sich, so der Verfasser abschließend, festhalten, dass die Entscheidung insofern nicht überraschend sei; jedoch sei die Feststellung, dass sich aus Verstößen gegen Art. 26 und Art. 30 DSGVO kein Verstoß gegen das Grundrecht auf den Schutz personenbezogener Daten nachweisen lasse überraschend und bedenklich. Auch überrasche es, dass der EuGH eher in einem Nebensatz feststelle, dass der Verantwortliche im Prozess aufgrund seiner Rechenschaftspflicht gegenüber Betroffenen beweisbelastet ist; ob sich die Kammer hier der möglichen Auswirkungen ihrer Ausführungen bewusst gewesen sei, bleibe fraglich. Y1 - 2023 N1 - Entscheidungsreport SP - 178 EP - 180 PB - DFV Mediengruppe CY - Frankfurt a.M. ER - TY - JOUR A1 - Golland, Alexander T1 - Immaterieller Schadensersatz bei Datenschutzverstößen – EuGH tariert aus JF - NWB - Steuer- und Wirtschaftsrecht N2 - Umsatzbasierte Bußgelder – wie sonst nur aus dem Kartellrecht bekannt – waren einer der Gründe, warum die Datenschutz-Grundverordnung (DSGVO) vor ihrem Inkrafttreten für erhebliches Aufsehen sorgte. Die vielfach relevanteren Schadensersatzansprüche, die, wie bei „Dieselgate“, aufgrund der Vielzahl von betroffenen Personen und der aus Sicht von Rechtsdienstleistern bestehenden Skalierbarkeit mit weitaus höheren Einbußen für Unternehmen einhergehen können, blieben zunächst unbeachtet. Inzwischen ist der Schadensersatzanspruch gem. Art. 82 DSGVO die Vorschrift, die die meisten Vorlagen zum Europäischen Gerichtshof (EuGH) der letzten Jahre hervorgerufen hat. Am 4.5.2023 hat nun der EuGH (Urteil v. 4.5.2023 - Rs. C-300/21, NWB GAAAJ-41389) in einem Grundsatzurteil über zentrale Fragen rund um den Ersatz immaterieller Schäden als Folge von Datenschutzverstößen entschieden. KW - Datenschutzgrundverordnung KW - Schadensersatz Y1 - 2023 SN - 0028-3460 VL - 2023 IS - 26 SP - 1845 EP - 1845 PB - NWB Verlag CY - Herne ER - TY - RPRT A1 - Siegert, Petra A1 - Bongaerts, Johannes A1 - Wagner, Torsten A1 - Schöning, Michael Josef A1 - Selmer, Thorsten T1 - Abschlussbericht zum Projekt zur Überwachung biotechnologischer Prozesse mittels Diacetyl-/Acetoin-Biosensor und Evaluierung von Acetoin-Reduktasen zur Verwendung in Biotransformationen Y1 - 2022 N1 - Laufzeit: 01.01.2016 – 31.12.2019 (verlängert bis 31.12.2020) Förderkennzeichen: 322-8.03.04.02-FH-Struktur 2016/02 Gefördert durch: Ministerium für Innovation, Wissenschaft und Forschung des Landes Nordrhein-Westfalen CY - Aachen ER - TY - CHAP A1 - Klöser, Lars A1 - Büsgen, André A1 - Kohl, Philipp A1 - Kraft, Bodo A1 - Zündorf, Albert ED - Conte, Donatello ED - Fred, Ana ED - Gusikhin, Oleg ED - Sansone, Carlo T1 - Explaining relation classification models with semantic extents T2 - Deep Learning Theory and Applications N2 - In recent years, the development of large pretrained language models, such as BERT and GPT, significantly improved information extraction systems on various tasks, including relation classification. State-of-the-art systems are highly accurate on scientific benchmarks. A lack of explainability is currently a complicating factor in many real-world applications. Comprehensible systems are necessary to prevent biased, counterintuitive, or harmful decisions. We introduce semantic extents, a concept to analyze decision patterns for the relation classification task. Semantic extents are the most influential parts of texts concerning classification decisions. Our definition allows similar procedures to determine semantic extents for humans and models. We provide an annotation tool and a software framework to determine semantic extents for humans and models conveniently and reproducibly. Comparing both reveals that models tend to learn shortcut patterns from data. These patterns are hard to detect with current interpretability methods, such as input reductions. Our approach can help detect and eliminate spurious decision patterns during model development. Semantic extents can increase the reliability and security of natural language processing systems. Semantic extents are an essential step in enabling applications in critical areas like healthcare or finance. Moreover, our work opens new research directions for developing methods to explain deep learning models. KW - Relation classification KW - Natural language processing KW - Natural language understanding KW - Information extraction KW - Trustworthy artificial intelligence Y1 - 2023 SN - 978-3-031-39058-6 (Print) SN - 978-3-031-39059-3 (Online) U6 - https://doi.org/10.1007/978-3-031-39059-3_13 N1 - 4th International Conference, DeLTA 2023, Rome, Italy, July 13–14, 2023. SP - 189 EP - 208 PB - Springer CY - Cham ER - TY - CHAP A1 - Freyer, Nils A1 - Thewes, Dustin A1 - Meinecke, Matthias ED - Gusikhin, Oleg ED - Hammoudi, Slimane ED - Cuzzocrea, Alfredo T1 - GUIDO: a hybrid approach to guideline discovery & ordering from natural language texts T2 - Proceedings of the 12th International Conference on Data Science, Technology and Applications DATA - Volume 1 N2 - Extracting workflow nets from textual descriptions can be used to simplify guidelines or formalize textual descriptions of formal processes like business processes and algorithms. The task of manually extracting processes, however, requires domain expertise and effort. While automatic process model extraction is desirable, annotating texts with formalized process models is expensive. Therefore, there are only a few machine-learning-based extraction approaches. Rule-based approaches, in turn, require domain specificity to work well and can rarely distinguish relevant and irrelevant information in textual descriptions. In this paper, we present GUIDO, a hybrid approach to the process model extraction task that first, classifies sentences regarding their relevance to the process model, using a BERT-based sentence classifier, and second, extracts a process model from the sentences classified as relevant, using dependency parsing. The presented approach achieves significantly better resul ts than a pure rule-based approach. GUIDO achieves an average behavioral similarity score of 0.93. Still, in comparison to purely machine-learning-based approaches, the annotation costs stay low. KW - Natural Language Processing KW - Text Mining KW - Process Model Extraction KW - Business Process Intelligence Y1 - 2023 SN - 978-989-758-664-4 U6 - https://doi.org/10.5220/0012084400003541 SN - 2184-285X N1 - 12th International Conference on Data Science, Technology and Applications, July 11-13, 2023, in Rome, Italy. SP - 335 EP - 342 ER - TY - JOUR A1 - Kempt, Hendrik A1 - Freyer, Nils A1 - Nagel, Saskia K. T1 - Justice and the normative standards of explainability in healthcare JF - Philosophy & Technology N2 - Providing healthcare services frequently involves cognitively demanding tasks, including diagnoses and analyses as well as complex decisions about treatments and therapy. From a global perspective, ethically significant inequalities exist between regions where the expert knowledge required for these tasks is scarce or abundant. One possible strategy to diminish such inequalities and increase healthcare opportunities in expert-scarce settings is to provide healthcare solutions involving digital technologies that do not necessarily require the presence of a human expert, e.g., in the form of artificial intelligent decision-support systems (AI-DSS). Such algorithmic decision-making, however, is mostly developed in resource- and expert-abundant settings to support healthcare experts in their work. As a practical consequence, the normative standards and requirements for such algorithmic decision-making in healthcare require the technology to be at least as explainable as the decisions made by the experts themselves. The goal of providing healthcare in settings where resources and expertise are scarce might come with a normative pull to lower the normative standards of using digital technologies in order to provide at least some healthcare in the first place. We scrutinize this tendency to lower standards in particular settings from a normative perspective, distinguish between different types of absolute and relative, local and global standards of explainability, and conclude by defending an ambitious and practicable standard of local relative explainability. KW - Clinical decision support systems KW - Justice KW - Medical AI KW - Explainability KW - Normative standards Y1 - 2022 U6 - https://doi.org/10.1007/s13347-022-00598-0 VL - 35 IS - Article number: 100 SP - 1 EP - 19 PB - Springer Nature CY - Berlin ER - TY - CHAP A1 - Nikolovski, Gjorgji A1 - Limpert, Nicolas A1 - Nessau, Hendrik A1 - Reke, Michael A1 - Ferrein, Alexander T1 - Model-predictive control with parallelised optimisation for the navigation of autonomous mining vehicles T2 - 2023 IEEE Intelligent Vehicles Symposium (IV) N2 - The work in modern open-pit and underground mines requires the transportation of large amounts of resources between fixed points. The navigation to these fixed points is a repetitive task that can be automated. The challenge in automating the navigation of vehicles commonly used in mines is the systemic properties of such vehicles. Many mining vehicles, such as the one we have used in the research for this paper, use steering systems with an articulated joint bending the vehicle’s drive axis to change its course and a hydraulic drive system to actuate axial drive components or the movements of tippers if available. To address the difficulties of controlling such a vehicle, we present a model-predictive approach for controlling the vehicle. While the control optimisation based on a parallel error minimisation of the predicted state has already been established in the past, we provide insight into the design and implementation of an MPC for an articulated mining vehicle and show the results of real-world experiments in an open-pit mine environment. KW - Mpc KW - Control KW - Path-following KW - Navigation KW - Automation Y1 - 2023 SN - 979-8-3503-4691-6 (Online) SN - 979-8-3503-4692-3 (Print) U6 - https://doi.org/10.1109/IV55152.2023.10186806 N1 - IEEE Symposium on Intelligent Vehicle, 4.-7. June 2023, Anchorage, AK, USA. PB - IEEE ER - TY - CHAP A1 - Kohl, Philipp A1 - Freyer, Nils A1 - Krämer, Yoka A1 - Werth, Henri A1 - Wolf, Steffen A1 - Kraft, Bodo A1 - Meinecke, Matthias A1 - Zündorf, Albert ED - Conte, Donatello ED - Fred, Ana ED - Gusikhin, Oleg ED - Sansone, Carlo T1 - ALE: a simulation-based active learning evaluation framework for the parameter-driven comparison of query strategies for NLP T2 - Deep Learning Theory and Applications N2 - Supervised machine learning and deep learning require a large amount of labeled data, which data scientists obtain in a manual, and time-consuming annotation process. To mitigate this challenge, Active Learning (AL) proposes promising data points to annotators they annotate next instead of a subsequent or random sample. This method is supposed to save annotation effort while maintaining model performance. However, practitioners face many AL strategies for different tasks and need an empirical basis to choose between them. Surveys categorize AL strategies into taxonomies without performance indications. Presentations of novel AL strategies compare the performance to a small subset of strategies. Our contribution addresses the empirical basis by introducing a reproducible active learning evaluation (ALE) framework for the comparative evaluation of AL strategies in NLP. The framework allows the implementation of AL strategies with low effort and a fair data-driven comparison through defining and tracking experiment parameters (e.g., initial dataset size, number of data points per query step, and the budget). ALE helps practitioners to make more informed decisions, and researchers can focus on developing new, effective AL strategies and deriving best practices for specific use cases. With best practices, practitioners can lower their annotation costs. We present a case study to illustrate how to use the framework. KW - Active learning KW - Query learning KW - Natural language processing KW - Deep learning KW - Reproducible research Y1 - 2023 SN - 978-3-031-39058-6 (Print) SN - 978-3-031-39059-3 (Online) U6 - https://doi.org/10.1007/978-3-031-39059-3_16 N1 - 4th International Conference, DeLTA 2023, Rome, Italy, July 13–14, 2023. SP - 235 EP - 253 PB - Springer CY - Cham ER - TY - RPRT A1 - Haeger, Gerrit A1 - Bongaerts, Johannes A1 - Siegert, Petra T1 - Abschlussbericht Teil II: Eingehende Darstellung Neue biobasierte Lipopeptide aus nachhaltiger Produktion (LipoPep) Y1 - 2023 N1 - Förderkennzeichen: 13FH256PA6 Titel: FHprofUnt 2016: Neue biobasierte Lipopeptide aus nachhaltiger Produktion Laufzeit: 01.02.2019 – 31.10.2022 ER - TY - CHAP A1 - Büsgen, André A1 - Klöser, Lars A1 - Kohl, Philipp A1 - Schmidts, Oliver A1 - Kraft, Bodo A1 - Zündorf, Albert ED - Cuzzocrea, Alfredo ED - Gusikhin, Oleg ED - Hammoudi, Slimane ED - Quix, Christoph T1 - From cracked accounts to fake IDs: user profiling on German telegram black market channels T2 - Data Management Technologies and Applications N2 - Messenger apps like WhatsApp and Telegram are frequently used for everyday communication, but they can also be utilized as a platform for illegal activity. Telegram allows public groups with up to 200.000 participants. Criminals use these public groups for trading illegal commodities and services, which becomes a concern for law enforcement agencies, who manually monitor suspicious activity in these chat rooms. This research demonstrates how natural language processing (NLP) can assist in analyzing these chat rooms, providing an explorative overview of the domain and facilitating purposeful analyses of user behavior. We provide a publicly available corpus of annotated text messages with entities and relations from four self-proclaimed black market chat rooms. Our pipeline approach aggregates the extracted product attributes from user messages to profiles and uses these with their sold products as features for clustering. The extracted structured information is the foundation for further data exploration, such as identifying the top vendors or fine-granular price analyses. Our evaluation shows that pretrained word vectors perform better for unsupervised clustering than state-of-the-art transformer models, while the latter is still superior for sequence labeling. KW - Clustering KW - Natural language processing KW - Information extraction KW - Profile extraction KW - Text mining Y1 - 2023 SN - 978-3-031-37889-8 (Print) SN - 978-3-031-37890-4 (Online) U6 - https://doi.org/10.1007/978-3-031-37890-4_9 N1 - 10th International Conference, DATA 2021, Virtual Event, July 6–8, 2021, and 11th International Conference, DATA 2022, Lisbon, Portugal, July 11-13, 2022 SP - 176 EP - 202 PB - Springer CY - Cham ER - TY - JOUR T1 - Dimensionen 2-2022: Magazin der FH Aachen University of Applied Sciences - Werkstatt Zukunft N2 - Werkstatt Zukunft - Die FH Aachen versteht sich als interdisziplinäre Ideenschmiede 04| Aufbruch ins Ungewisse 08| Mit Altpapierresten aus der Energiekrise 14| Mehr Power für die Energiewende 20| Pfadfinder im Datendschungel 23| Ein historischer Schritt 24| Gemeinsam vorwärts 30| Für eine gerechte Hochschule. Für alle. 32| Der grüne Reiter 34| Vom Flugsimulator bis zum Roboter 36| Unsere Azubis sind top! 38| WIR sind ein Sportteam! 40| Effizient und sicher: Der Bergbau der Zukunft 46| Mit Sonnenlicht zu sauberem Trinkwasser 48| Neue Brandmeldeanlage für den Dom zu Aachen 50| Auszeichnung für außergewöhnliches Engagement 52| Neue Ideen für Schloss Lichtenburg 55| Kopfnuss 56| One-Man-Show 60| Kämpferin für das Schöne 61| Ein charmanter Diplomat 62| Teamplay für die Zukunft 63| Impressum T3 - Dimensionen - Magazin der FH Aachen University of Applied Sciences - 2022, 2 Y1 - 2022 CY - Aachen ER - TY - JOUR A1 - Schulze, Sven A1 - Feyerl, Günter A1 - Pischinger, Stefan T1 - Advanced ECMS for hybrid electric heavy-duty trucks with predictive battery discharge and adaptive operating strategy under real driving conditions JF - Energies N2 - To fulfil the CO2 emission reduction targets of the European Union (EU), heavy-duty (HD) trucks need to operate 15% more efficiently by 2025 and 30% by 2030. Their electrification is necessary as conventional HD trucks are already optimized for the long-haul application. The resulting hybrid electric vehicle (HEV) truck gains most of the fuel saving potential by the recuperation of potential energy and its consecutive utilization. The key to utilizing the full potential of HEV-HD trucks is to maximize the amount of recuperated energy and ensure its intelligent usage while keeping the operating point of the internal combustion engine as efficient as possible. To achieve this goal, an intelligent energy management strategy (EMS) based on ECMS is developed for a parallel HEV-HD truck which uses predictive discharge of the battery and adaptive operating strategy regarding the height profile and the vehicle mass. The presented EMS can reproduce the global optimal operating strategy over long phases and lead to a fuel saving potential of up to 2% compared with a heuristic strategy. Furthermore, the fuel saving potential is correlated with the investigated boundary conditions to deepen the understanding of the impact of intelligent EMS for HEV-HD trucks. KW - Energy management strategies KW - ECMS KW - CO2 emission reduction targets KW - Driving cycle recognition KW - Predictive battery discharge Y1 - 2023 U6 - https://doi.org/10.3390/en16135171 SN - 1996-1073 N1 - The article belongs to the Special Issue "Energy Management Strategies of Electrified Vehicles toward the Real-World Driving". VL - 16 IS - 13 PB - MDPI CY - Basel ER - TY - THES A1 - Leßmann, Mika T1 - Designing confidence : eine patient:innenzentrierte Intervention für belastende Behandlungssituationen - am Beispiel von Strahlentherapie N2 - Krebstherapie bei Kindern ist für alle Beteiligten eine emotional bedrückende Angelegenheit. Besonders die Strahlentherapie stellt Kinder aufgrund der Häufigkeit der Termine, der Isolation während der Bestrahlung und der Fixierung vor Herausforderungen. „nia“ ermöglicht es den Angehörigen, während der Behandlung einen physischen Kontakt zum Kind zu halten. Zwei miteinander verbundene Zwillingsgeräte registrieren die Bewegungen der Hände und übertragen die Berührung an das jeweils andere Gerät. Diese taktile Kommunikation sorgt für innere Ruhe und Verbundenheit. Vor der eigentlichen Therapie liegen die Geräte in einem Koffer, welcher ein Modell des Behandlungsraums beinhaltet. Mithilfe dessen werden die Kinder spielerisch auf die Bestrahlung vorbereitet. So sollen sich in Zukunft weniger Kinder ängstlich und allein einer Strahlentherapie stellen müssen. KW - Produktdesign KW - Medizindesign KW - Krebs KW - Kinder KW - Emotionen Y1 - 2023 PB - FH Aachen CY - Aachen ER - TY - THES A1 - Nahrings, Laura Aileen T1 - Seamless Connection : die Integration eines smarten WLAN Routers in die Wohnumgebung N2 - In Deutschland verfügen mehr als 95 % aller Haushalte über einen Internetzugang und das Interesse an Smart Home Anwendungen steigt. Je vernetzter das Zuhause wird, desto mehr Devices müssen dort ihren Platz finden. WLAN Router wirken durch ihre technische Designsprache meist wie Fremdkörper im Raum, sodass oft versucht wird, sie zu verstecken. Das soll sich mit „Cobo“, dem smarten WLAN Router, ändern. Neben der Bereitstellung einer Internetanbindung wird er zum Hub für alle Smart Home Anwendungen. Als Herzstück des Zuhauses sorgt er für die Vernetzung aller Devices und schafft zudem eine Verbindung zwischen Technologie und Interior. Mit seinem minimalistischen Design und der gezielten Auswahl an Materialien und Farben fügt sich der intelligente Router in die eigenen vier Wände ein. „Cobo“ ist kein WLAN Router, der im Schuhregal versteckt werden muss, denn er wird zum Teil der Einrichtung. KW - Router KW - Wifi KW - Smarthome KW - Produktdesign KW - Seamlessconnection Y1 - 2023 PB - FH Aachen CY - Aachen ER - TY - THES A1 - Rabe, Leonie Maria T1 - Wohlfühlen in den eigenen vier Wänden : ein Produkt, welches die Wohn- und Lebensqualität steigert. N2 - Viele Menschen fühlen sich in ihren eigenen vier Wänden nicht wohl. Sie sind gestresst und können nicht entspannen. Ziel dieser Arbeit ist es, ein Produkt zu erschaffen, welches in seinen Funktionen und seinem Design dafür sorgt, dass die Nutzer:innen sich zu Hause wohler fühlen. Es soll alle Funktionen vereinen, die dafür sorgen, dass der Alltagsstress besser bewältigt werden kann und man in seinem Zuhause entspannen kann und den Moment mehr genießt. Entstanden ist Iwa, ein Produkt, welches zum einen als Luftreiniger arbeitet und die Raumluft filtert und im Zusammenspiel mit Licht und Musik die Raumatmosphäre verbessert und so Stress mindert. Das Design soll genau wie die Funktionen beruhigend, entspannend und erdend wirken. Es ist angelehnt am Zen-Design. So bietet Iwa einen großen Mehrwert. Die Funktionen sorgen im Zusammenspiel mit dem Design für eine verbesserte Wohn- und Lebensqualität. KW - Raumatmosphäre KW - entspannen KW - Zen KW - Luftreiniger KW - Licht Y1 - 2023 PB - FH Aachen CY - Aachen ER - TY - THES A1 - Tschiersch, Lina Sofie T1 - Cooking for wellbeing : Küchensystem für Menschen mit Alzheimer-Demenz N2 - Essen zuzubereiten bedeutet für viele Menschen Normalität, es bestimmt Teile ihrer Identität und ist eng verbunden mit Familie und Kultur. Der Beginn der Alzheimererkrankung erschwert diese Tätigkeit, oft muss sie aus Sicherheitsgründen aufgegeben werden. Kochen als Therapieansatz hat zur Verbesserung der Aktivität und Verringerung von Stress beigetragen. Pila ist ein Küchensystem, das Kochenthusiasten begleitet und Selbstständigkeit sowie Partizipation ermöglicht. Das Kompetenzgefühl, die Autonomie und die Verbundenheit zu betreuenden Personen stärken das Wohlbefinden. Das System führt die Nutzerinnen und Nutzer digital durch alle Phasen von der Vorbereitung bis zum Aufräumen. Aus den Elementen entsteht ein klar organisierter Arbeitsplatz ohne Ablenkungen und mit eindeutigen Aktionspunkten. Die Funktionen der Kocheinheit sind simplifiziert und bedürfnisgerecht angepasst. KW - Industriedesign KW - Küche KW - Inklusiv KW - Kochen KW - Haushaltsgerät Y1 - 2023 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER - TY - THES A1 - Vonderhagen, Lisa T1 - KiBix : Fahrradfahren für Kinder - das nachhaltige Kinderfahrrad aus Kunststoff als Abo-Sharing-System N2 - Jedes Jahr werden Hunderttausende Fahrradrahmen produziert. 90 % davon werden in Asien hergestellt und von dort über die ganze Welt versendet. Mehr als 80 % der Rahmen werden nach der Nutzung wieder nach Asien zurückgeschickt und landen dort auf riesigen Fahrradfriedhöfen. Das Kinderfahrradkonzept "KiBix" wirkt diesem Problem entgegen, indem es eine Alternative für das regelmäßige Kaufen von neuen Kinderfahrrädern bietet. Im Fokus stehen der Kinderfahrradrahmen und die Gabel aus Kunststoff, welche im Spritzgussverfahren produziert werden. Das City-Bike ist in ein Abo-Sharing-System mit Rädern in unterschiedlichen Größen eingebettet, welches durch eine monatliche Gebühr wie das Eigene genutzt werden kann. Der hohlgespritzte Rahmen ermöglicht die Integration kleiner Boxen im Inneren, in denen Kinder ihre persönlichen "Schätze" mitnehmen können. Somit vereint das Konzept die drei Segmente Material/Produktion, Sharing-System und die Mitnahme des "Schatzes". "KiBix" gibt Kindern in Zeiten der Digitalisierung und der globalen Erwärmung die Möglichkeit, selbstbestimmt und nachhaltig die Welt zu erkunden. KW - Kinderfahrrad KW - Nachhaltig KW - Mobil KW - Design KW - Sharing Y1 - 2023 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER - TY - THES A1 - Mok, Pia Peixia T1 - Flowcean Qi : a gentle Reminder to take a deep breath. N2 - Atmen tut jeder, automatisch. Es wird nicht auf die Ausführung geachtet. Doch was, wenn nur ein wenig Feinschliff an unserer Atmung bereits Großes für unsere Gesundheit bewirkt? Von etlichen unterschiedlichen Studien wurde bezeugt, dass Atmung und Empfinden eins sind. Das persönliche Empfinden ist unser Portal zur Außenwelt. Die Art wie wir auf äußerliche Reize reagieren, wie achtsam wir im Tun und Denken sind, spiegelt unsere Innenwelt und körperliches Wohlbefinden wieder. FLOWCEAN QI dient dazu, Stress- und Angststörungen im Alltagsleben für Berufstätige mit hohem Stressfaktor zu reduzieren. Vor allem, um das Gesundheitssystem zu entlasten und die Psyche der Menschen gesund wieder aufzubauen. Sind Berufstätige viel gelassener, steigen auch Leistung und Produktivität. Es ist immer wichtig, die Kernursache von Problemen zu finden und zu lösen. So können auch vielerlei andere auf die Psyche zurückzuführende Probleme der Gesellschaft gelöst werden. FLOWCEAN QI agiert durch modernste Technologie aktiv mit dem Nutzer. Die KI-Assistenz gestaltet das Lernen der Atemtechniken spaßiger, was wiederum den Lerneffekt verbessert. Der Beamer wird im Innenbereich platziert und der Tracker begleitet einen unterwegs und zeichnet die Datenanalyse auf. Für mehr Datenschutz ist das Armband ein reines offline Produkt. Förmlich sollte es dem Nutzer nah sein, naturverbunden, vertrauenswürdig und beruhigend wirken. FLOWCEAN QI basiert gestalterisch auf eine antike japanische Philosophie namens „Kintsugi“. Nach der japanischen Philosophie Kintsugi werden zerbrochene Teegläser wiederzusammengeklebt statt weggeworfen. Die in Teile getrennten Elemente werden glatt und geschmeidig wieder zusammengefügt. Sie formen ein neues Ganzes, dass die Schönheit des Originals meist übertrifft. Die Ästhetik hinter „Kintsugi“ nennt man „Wabi-Sabi“. Es bedeutet, die Schönheit im Vergänglichen, Alten oder Fehlerhaften zu verstehen. Die Philosophie dahinter wird metaphorisch auf das Design abgebildet und auf unsere Gesundheit übertragen. Statt letztere zu ignorieren, schenken wir ihr unsere volle Aufmerksamkeit. Ziel der Produkte ist, uns stets an sie zu erinnern, sodass wir täglich an unserem Wohlbefinden arbeiten können. KW - Atmen KW - KI KW - Stress KW - Japan KW - Angststörungen Y1 - 2023 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER - TY - CHAP A1 - Goh, Kheng Lim A1 - Topçu, Murat A1 - Madabhushi, Gopal S. P. A1 - Staat, Manfred ED - Maia, Fatima Raquel Azevedo ED - Miguel Oliveira, J. ED - Reis, Rui L. T1 - Collagen fibril reinforcement in connective tissue extracellular matrices T2 - Handbook of the extracellular matrix N2 - The connective tissues such as tendons contain an extracellular matrix (ECM) comprising collagen fibrils scattered within the ground substance. These fibrils are instrumental in lending mechanical stability to tissues. Unfortunately, our understanding of how collagen fibrils reinforce the ECM remains limited, with no direct experimental evidence substantiating current theories. Earlier theoretical studies on collagen fibril reinforcement in the ECM have relied predominantly on the assumption of uniform cylindrical fibers, which is inadequate for modelling collagen fibrils, which possessed tapered ends. Recently, Topçu and colleagues published a paper in the International Journal of Solids and Structures, presenting a generalized shear-lag theory for the transfer of elastic stress between the matrix and fibers with tapered ends. This paper is a positive step towards comprehending the mechanics of the ECM and makes a valuable contribution to formulating a complete theory of collagen fibril reinforcement in the ECM. KW - Connective tissues KW - Extracellular matrix (ECM) KW - Collagen fibrils KW - Mechanical stability KW - Tapered ends Y1 - 2023 SN - 978-3-030-92090-6 (Print) SN - 978-3-030-92090-6 (Online) U6 - https://doi.org/10.1007/978-3-030-92090-6_6-1 SP - 1 EP - 20 PB - Springer Nature CY - Cham ER - TY - CHAP A1 - Mohan, Nijanthan A1 - Groß, Rolf Fritz A1 - Menzel, Karsten A1 - Theis, Fabian T1 - Opportunities and Challenges in the Implementation of Building Information Modeling for Prefabrication of Heating, Ventilation and Air Conditioning Systems in Small and Medium-Sized Contracting Companies in Germany – A Case Study T2 - WIT Transactions on The Built Environment, Vol. 205 N2 - Even though BIM (Building Information Modelling) is successfully implemented in most of the world, it is still in the early stages in Germany, since the stakeholders are sceptical of its reliability and efficiency. The purpose of this paper is to analyse the opportunities and obstacles to implementing BIM for prefabrication. Among all other advantages of BIM, prefabrication is chosen for this paper because it plays a vital role in creating an impact on the time and cost factors of a construction project. The project stakeholders and participants can explicitly observe the positive impact of prefabrication, which enables the breakthrough of the scepticism factor among the small-scale construction companies. The analysis consists of the development of a process workflow for implementing prefabrication in building construction followed by a practical approach, which was executed with two case studies. It was planned in such a way that, the first case study gives a first-hand experience for the workers at the site on the BIM model so that they can make much use of the created BIM model, which is a better representation compared to the traditional 2D plan. The main aim of the first case study is to create a belief in the implementation of BIM Models, which was succeeded by the execution of offshore prefabrication in the second case study. Based on the case studies, the time analysis was made and it is inferred that the implementation of BIM for prefabrication can reduce construction time, ensures minimal wastes, better accuracy, less problem-solving at the construction site. It was observed that this process requires more planning time, better communication between different disciplines, which was the major obstacle for successful implementation. This paper was carried out from the perspective of small and medium-sized mechanical contracting companies for the private building sector in Germany. KW - building information modelling KW - HVAC KW - prefabrication KW - construction KW - small and medium scaled companies Y1 - 2021 U6 - https://doi.org/10.2495/BIM210101 SN - 1743-3509 N1 - 4th International Conference on Building Information Modelling (BIM) in Design, Construction and Operations, 1–3 September 2021. Santiago de Compostela, Spain SP - 117 EP - 126 PB - WIT Press CY - Southampton ER - TY - CHAP A1 - Schulze-Buxloh, Lina A1 - Groß, Rolf Fritz T1 - Miniature urban farming plant: a complex educational “Toy” for engineering students T2 - The Future of Education 11th Edition 2021 N2 - Urban farming is an innovative and sustainable way of food production and is becoming more and more important in smart city and quarter concepts. It also enables the production of certain foods in places where they usually dare not produced, such as production of fish or shrimps in large cities far away from the coast. Unfortunately, it is not always possible to show students such concepts and systems in real life as part of courses: visits of such industry plants are sometimes not possible because of distance or are permitted by the operator for hygienic reasons. In order to give the students the opportunity of getting into contact with such an urban farming system and its complex operation, an industrial urban farming plant was set up on a significantly smaller scale. Therefore, all needed technical components like water aeriation, biological and mechanical filtration or water circulation have been replaced either by aquarium components or by self-designed parts also using a 3D-printer. Students from different courses like mechanical engineering, smart building engineering, biology, electrical engineering, automation technology and civil engineering were involved in this project. This “miniature industrial plant” was also able to start operation and has now been running for two years successfully. Due to Corona pandemic, home office and remote online lectures, the automation of this miniature plant should be brought to a higher level in future for providing a good control over the system and water quality remotely. The aim of giving the student a chance to get to know the operation of an urban farming plant was very well achieved and the students had lots of fun in “playing” and learning with it in a realistic way. KW - urban farming KW - food production KW - smart engineering KW - 3D printing KW - sustainability Y1 - 2021 N1 - FOE 2021 : The Future of Education International Conference – Fully Virtual Edition; 01.07.2021-02.07.2021; Florence, Italy ER - TY - CHAP A1 - Fissabre, Anke A1 - Wilson, Ariane ED - Di Teodoro, Francesco P. ED - Ferretti, Emanuela ED - Frommel, Sabine ED - Schlimme, Hermann T1 - Hypotheses on the Tower of Monthoiron: A Built Design of Italian and Leonardian Inspiration in France T2 - Leonardo da Vinci: l’architettura / Léonard de Vinci : l’architecture Y1 - 2022 SN - 979-12-80956-00-2 N1 - Sprachen laut Verlagsangaben: Italienisch, Englisch, Französisch SP - 287 EP - 300 PB - Campisano Editore CY - Roma ER - TY - JOUR A1 - Vögele, Stefan A1 - Josyabhatla, Vishnu Teja A1 - Ball, Christopher A1 - Rhoden, Imke A1 - Grajewski, Matthias A1 - Rübbelke, Dirk A1 - Kuckshinrichs, Wilhelm T1 - Robust assessment of energy scenarios from stakeholders' perspectives JF - Energy N2 - Using scenarios is vital in identifying and specifying measures for successfully transforming the energy system. Such transformations can be particularly challenging and require the support of a broader set of stakeholders. Otherwise, there will be opposition in the form of reluctance to adopt the necessary technologies. Usually, processes for considering stakeholders' perspectives are very time-consuming and costly. In particular, there are uncertainties about how to deal with modifications in the scenarios. In principle, new consulting processes will be required. In our study, we show how multi-criteria decision analysis can be used to analyze stakeholders' attitudes toward transition paths. Since stakeholders differ regarding their preferences and time horizons, we employ a multi-criteria decision analysis approach to identify which stakeholders will support or oppose a transition path. We provide a flexible template for analyzing stakeholder preferences toward transition paths. This flexibility comes from the fact that our multi-criteria decision aid-based approach does not involve intensive empirical work with stakeholders. Instead, it involves subjecting assumptions to robustness analysis, which can help identify options to influence stakeholders' attitudes toward transitions. Y1 - 2023 U6 - https://doi.org/10.1016/j.energy.2023.128326 SN - 1873-6785 (Online) SN - 0360-5442 (Print) IS - In Press, Article 128326 PB - Elsevier CY - Amsterdam ER - TY - JOUR A1 - Waldvogel, Janice A1 - Freyler, Kathrin A1 - Helm, Michael A1 - Monti, Elena A1 - Stäudle, Benjamin A1 - Gollhofer, Albert A1 - Narici, Marco V. A1 - Ritzmann, Ramona A1 - Albracht, Kirsten T1 - Changes in gravity affect neuromuscular control, biomechanics, and muscle-tendon mechanics in energy storage and dissipation tasks JF - Journal of Applied Physiology N2 - This study evaluates neuromechanical control and muscle-tendon interaction during energy storage and dissipation tasks in hypergravity. During parabolic flights, while 17 subjects performed drop jumps (DJs) and drop landings (DLs), electromyography (EMG) of the lower limb muscles was combined with in vivo fascicle dynamics of the gastrocnemius medialis, two-dimensional (2D) kinematics, and kinetics to measure and analyze changes in energy management. Comparisons were made between movement modalities executed in hypergravity (1.8 G) and gravity on ground (1 G). In 1.8 G, ankle dorsiflexion, knee joint flexion, and vertical center of mass (COM) displacement are lower in DJs than in DLs; within each movement modality, joint flexion amplitudes and COM displacement demonstrate higher values in 1.8 G than in 1 G. Concomitantly, negative peak ankle joint power, vertical ground reaction forces, and leg stiffness are similar between both movement modalities (1.8 G). In DJs, EMG activity in 1.8 G is lower during the COM deceleration phase than in 1 G, thus impairing quasi-isometric fascicle behavior. In DLs, EMG activity before and during the COM deceleration phase is higher, and fascicles are stretched less in 1.8 G than in 1 G. Compared with the situation in 1 G, highly task-specific neuromuscular activity is diminished in 1.8 G, resulting in fascicle lengthening in both movement modalities. Specifically, in DJs, a high magnitude of neuromuscular activity is impaired, resulting in altered energy storage. In contrast, in DLs, linear stiffening of the system due to higher neuromuscular activity combined with lower fascicle stretch enhances the buffering function of the tendon, and thus the capacity to safely dissipate energy. KW - electromyography KW - locomotion KW - overload KW - stretch-shortening cycle KW - ultrasound Y1 - 2023 U6 - https://doi.org/10.1152/japplphysiol.00279.2022 SN - 1522-1601 (Onlineausgabe) SN - 8750-7587 (Druckausgabe) VL - 134 IS - 1 SP - 190 EP - 202 PB - American Physiological Society CY - Bethesda, Md. ER - TY - JOUR A1 - Luft, Angela A1 - Bremen, Sebastian A1 - Luft, Nils T1 - A cost/benefit and flexibility evaluation framework for additive technologies in strategic factory planning JF - Processes N2 - There is a growing demand for more flexibility in manufacturing to counter the volatility and unpredictability of the markets and provide more individualization for customers. However, the design and implementation of flexibility within manufacturing systems are costly and only economically viable if applicable to actual demand fluctuations. To this end, companies are considering additive manufacturing (AM) to make production more flexible. This paper develops a conceptual model for the impact quantification of AM on volume and mix flexibility within production systems in the early stages of the factory-planning process. Together with the model, an application guideline is presented to help planners with the flexibility quantification and the factory design process. Following the development of the model and guideline, a case study is presented to indicate the potential impact additive technologies can have on manufacturing flexibility Within the case study, various scenarios with different production system configurations and production programs are analyzed, and the impact of the additive technologies on volume and mix flexibility is calculated. This work will allow factory planners to determine the potential impacts of AM on manufacturing flexibility in an early planning stage and design their production systems accordingly. KW - additive manufacturing KW - factory planning KW - manufacturing flexibility KW - volume flexibility KW - mix flexibility Y1 - 2023 U6 - https://doi.org/10.3390/pr11071968 SN - 2227-9717 VL - 11 IS - 7 PB - MDPI CY - Basel ER - TY - CHAP A1 - Engelmann, Ulrich M. A1 - Baumann, Martin ED - Lindinger, Markus ED - Bartsch, Oliver T1 - Moderationsexpertise - das Mindset T2 - IT-Servicemanagement N2 - Teamsitzungen, Arbeitsgruppentreffen, Kickoffs und Meetings – sie alle werden mit dem Ziel durchgeführt, innerhalb einer vorgegebenen Zeitspanne ein gemeinsames Arbeitsziel zu erreichen. Damit die Zielerreichung auch bei komplexeren Arbeitsaufträgen nicht vom Zufall abhängt, empfiehlt es sich, die Leitung des Ablaufs einem Moderator zu übertragen. In diesem Beitrag einer dreiteiligen Serie wird beschrieben, über welches Mindset der Moderator verfügen sollte, welche grundsätzlichen Methoden hilfreich sind und was bei der Onlinemoderation im Besonderen zu beachten ist. Y1 - 2023 SN - 978-3-8249-1154-7 SP - Kapitel 05530 PB - TÜV-Verlag CY - Köln ET - 54. Update ER - TY - CHAP A1 - Eggert, Mathias A1 - Weber, Jannik T1 - What drives the purchase decision in Instagram stores? T2 - ECIS 2023 Research Papers N2 - The popularity of social media and particularly Instagram grows steadily. People use the different platforms to share pictures as well as videos and to communicate with friends. The potential of social media platforms is also being used for marketing purposes and for selling products. While for Facebook and other online social media platforms the purchase decision factors are investigated several times, Instagram stores remain mainly unattended so far. The present research work closes this gap and sheds light into decisive factors for purchasing products offered in Instagram stores. A theoretical research model, which contains selected constructs that are assumed to have a significant influence on Instagram user´s purchase intention, is developed. The hypotheses are evaluated by applying structural equation modelling on survey data containing 127 relevant participants. The results of the study reveal that ‘trust’, ‘personal recommendation’, and ‘usability’ significantly influences user’s buying intention in Instagram stores. KW - Instagram store KW - shopping behavior KW - purchase factor KW - PLS KW - structural equation model Y1 - 2023 N1 - ECIS 2023, European Conference on Information Systems, Kristiansand, Norway, June 11.-16. SP - 1 EP - 17 ER - TY - CHAP A1 - Steuer-Dankert, Linda T1 - Training future skills - sustainability, interculturality & innovation in a digital design thinking format T2 - Proceedings of the 19th International CDIO Conference N2 - The complex questions of today for a world of tomorrow are characterized by their global impact. Solutions must therefore not only be sustainable in the sense of the three pillars of sustainability (economic, environmental, and social) but must also function globally. This goes hand in hand with the need for intercultural acceptance of developed services and products. To achieve this, engineers, as the problem solvers of the future, must be able to work in intercultural teams on appropriate solutions, and be sensitive to intercultural perspectives. To equip the engineers of the future with the so-called future skills, teaching concepts are needed in which students can acquire these methods and competencies in application-oriented formats. The presented course "Applying Design Thinking - Sustainability, Innovation and Interculturality" was developed to teach future skills from the competency areas Digital Key Competencies, Classical Competencies and Transformative Competencies. The CDIO Standard 3.0, in particular the standards 5, 6, 7 and 8, was used as a guideline. The course aims to prepare engineering students from different disciplines and cultures for their future work in an international environment by combining a digital teaching format with an interdisciplinary, transdisciplinary and intercultural setting for solving sustainability challenges. The innovative moment lies in the digital application of design thinking and the inclusion of intercultural as well as trans- and interdisciplinary perspectives in innovation development processes. In this paper, the concept of the course will be presented in detail and the particularities of a digital implementation of design thinking will be addressed. Subsequently, the potentials and challenges will be reflected and practical advice for integrating design thinking in engineering education will be given. KW - Design Thinking KW - Sustainability KW - Future Skills KW - Interculturality KW - Interdisciplinarity Y1 - 2023 N1 - 19th International CDIO Conference, hosted by NTNU, Trondheim, Norway, June 26-29, 2023 ER - TY - JOUR A1 - Rabehi, Amine A1 - Garlan, Benjamin A1 - Achtsnicht, Stefan A1 - Krause, Hans-Joachim A1 - Offenhäusser, Andreas A1 - Ngo, Kieu A1 - Neveu, Sophie A1 - Graff-Dubois, Stephanie A1 - Kokabi, Hamid T1 - Magnetic detection structure for Lab-on-Chip applications based on the frequency mixing technique JF - Sensors N2 - A magnetic frequency mixing technique with a set of miniaturized planar coils was investigated for use with a completely integrated Lab-on-Chip (LoC) pathogen sensing system. The system allows the detection and quantification of superparamagnetic beads. Additionally, in terms of magnetic nanoparticle characterization ability, the system can be used for immunoassays using the beads as markers. Analytical calculations and simulations for both excitation and pick-up coils are presented; the goal was to investigate the miniaturization of simple and cost-effective planar spiral coils. Following these calculations, a Printed Circuit Board (PCB) prototype was designed, manufactured, and tested for limit of detection, linear response, and validation of theoretical concepts. Using the magnetic frequency mixing technique, a limit of detection of 15 µg/mL of 20 nm core-sized nanoparticles was achieved without any shielding. KW - Lab-on-Chip KW - magnetic sensing KW - frequency mixing KW - superparamagnetic nanoparticles KW - magnetic beads Y1 - 2018 U6 - https://doi.org/10.3390/s18061747 SN - 1424-8220 VL - 18 IS - 6 PB - MDPI CY - Basel ER - TY - CHAP A1 - Engelmann, Ulrich M. A1 - Baumann, Martin ED - Thomann, Hermann ED - Träger, Thomas T1 - Moderationsexpertise für QMBs – das Mindset T2 - Qualitätsmanagement in Dienstleistungsunternehmen N2 - Teamsitzungen, Arbeitsgruppentreffen, Kickoffs und Meetings – sie alle werden mit dem Ziel durchgeführt, innerhalb einer vorgegebenen Zeitspanne ein gemeinsames Arbeitsziel zu erreichen. Damit die Zielerreichung auch bei komplexeren Arbeitsaufträgen nicht vom Zufall abhängt, empfiehlt es sich, die Leitung des Ablaufs einem Moderator zu übertragen. In diesem Beitrag einer mehrteiligen Serie wird beschrieben, über welches Mindset der Moderator verfügen sollte, welche grundsätzlichen Methoden hilfreich sind und was bei der Onlinemoderation im Besonderen zu beachten ist. Y1 - 2023 SN - 978-3-8249-0473-0 SP - Kapitel 08630 PB - TÜV-Verlag CY - Köln ER - TY - JOUR A1 - Achtsnicht, Stefan A1 - Schönenborn, Kristina A1 - Offenhäusser, Andreas A1 - Krause, Hans-Joachim T1 - Measurement of the magnetophoretic velocity of different superparamagnetic beads JF - Journal of Magnetism and Magnetic Materials N2 - The movement of magnetic beads due to a magnetic field gradient is of great interest in different application fields. In this report we present a technique based on a magnetic tweezers setup to measure the velocity factor of magnetically actuated individual superparamagnetic beads in a fluidic environment. Several beads can be tracked simultaneously in order to gain and improve statistics. Furthermore we show our results for different beads with hydrodynamic diameters between 200 and 1000 nm from diverse manufacturers. These measurement data can, for example, be used to determine design parameters for a magnetic separation system, like maximum flow rate and minimum separation time, or to select suitable beads for fixed experimental requirements. KW - magnetophoretic velocity KW - superparamagnetic bead KW - magnetic tweezers KW - magnetic separation KW - magnetic actuation Y1 - 2019 U6 - https://doi.org/10.1016/j.jmmm.2018.10.066 SN - 0304-8853 VL - 477 IS - 1 SP - 244 EP - 248 PB - Elsevier CY - Amsterdam ER - TY - CHAP A1 - Baier, Ralph A1 - Brauner, Philipp A1 - Brillowski, Florian A1 - Dammers, Hannah A1 - Liehner, Luca A1 - Pütz, Sebastian A1 - Schneider, Sebastian A1 - Schollemann, Alexander A1 - Steuer-Dankert, Linda A1 - Vervier, Luisa A1 - Gries, Thomas A1 - Leicht-Scholten, Carmen A1 - Mertens, Alexander A1 - Nagel, Saskia K. A1 - Schuh, Günther A1 - Ziefle, Martina A1 - Nitsch, Verena ED - Brecher, Christian ED - Schuh, Günther ED - van der Alst, Wil ED - Jarke, Matthias ED - Piller, Frank T. ED - Padberg, Melanie T1 - Human-centered work design for the internet of production T2 - Internet of production - fundamentals, applications and proceedings N2 - Like all preceding transformations of the manufacturing industry, the large-scale usage of production data will reshape the role of humans within the sociotechnical production ecosystem. To ensure that this transformation creates work systems in which employees are empowered, productive, healthy, and motivated, the transformation must be guided by principles of and research on human-centered work design. Specifically, measures must be taken at all levels of work design, ranging from (1) the work tasks to (2) the working conditions to (3) the organizational level and (4) the supra-organizational level. We present selected research across all four levels that showcase the opportunities and requirements that surface when striving for human-centered work design for the Internet of Production (IoP). (1) On the work task level, we illustrate the user-centered design of human-robot collaboration (HRC) and process planning in the composite industry as well as user-centered design factors for cognitive assistance systems. (2) On the working conditions level, we present a newly developed framework for the classification of HRC workplaces. (3) Moving to the organizational level, we show how corporate data can be used to facilitate best practice sharing in production networks, and we discuss the implications of the IoP for new leadership models. Finally, (4) on the supra-organizational level, we examine overarching ethical dimensions, investigating, e.g., how the new work contexts affect our understanding of responsibility and normative values such as autonomy and privacy. Overall, these interdisciplinary research perspectives highlight the importance and necessary scope of considering the human factor in the IoP. KW - Responsibility KW - Privacy KW - Digital leadership KW - Best practice sharing KW - Cognitive assistance system KW - Human-robot collaboration KW - Human-centered work design Y1 - 2023 SN - 978-3-030-98062-7 U6 - https://doi.org/10.1007/978-3-030-98062-7_19-1 N1 - Part of the book series: Interdisciplinary Excellence Accelerator Series (IDEAS) SP - 1 EP - 23 PB - Springer CY - Cham ER - TY - JOUR A1 - Achtsnicht, Stefan A1 - Tödter, Julia A1 - Niehues, Julia A1 - Telöken, Matthias A1 - Offenhäusser, Andreas A1 - Krause, Hans-Joachim A1 - Schröper, Florian T1 - 3D printed modular immunofiltration columns for frequency mixing-based multiplex magnetic immunodetection JF - Sensors N2 - For performing point-of-care molecular diagnostics, magnetic immunoassays constitute a promising alternative to established enzyme-linked immunosorbent assays (ELISA) because they are fast, robust and sensitive. Simultaneous detection of multiple biomolecular targets from one body fluid sample is desired. The aim of this work is to show that multiplex magnetic immunodetection based on magnetic frequency mixing by means of modular immunofiltration columns prepared for different targets is feasible. By calculations of the magnetic response signal, the required spacing between the modules was determined. Immunofiltration columns were manufactured by 3D printing and antibody immobilization was performed in a batch approach. It was shown experimentally that two different target molecules in a sample solution could be individually detected in a single assaying step with magnetic measurements of the corresponding immobilization filters. The arrangement order of the filters and of a negative control did not influence the results. Thus, a simple and reliable approach to multi-target magnetic immunodetection was demonstrated. Y1 - 2019 U6 - https://doi.org/10.3390/s19010148 SN - 1424-8220 VL - 19 IS - 1 PB - MDPI CY - Basel ER - TY - JOUR A1 - Achtsnicht, Stefan A1 - Pourshahidi, Ali Mohammad A1 - Offenhäusser, Andreas A1 - Krause, Hans-Joachim T1 - Multiplex detection of different magnetic beads using frequency scanning in magnetic frequency mixing technique JF - Sensors N2 - In modern bioanalytical methods, it is often desired to detect several targets in one sample within one measurement. Immunological methods including those that use superparamagnetic beads are an important group of techniques for these applications. The goal of this work is to investigate the feasibility of simultaneously detecting different superparamagnetic beads acting as markers using the magnetic frequency mixing technique. The frequency of the magnetic excitation field is scanned while the lower driving frequency is kept constant. Due to the particles’ nonlinear magnetization, mixing frequencies are generated. To record their amplitude and phase information, a direct digitization of the pickup-coil’s signal with subsequent Fast Fourier Transformation is performed. By synchronizing both magnetic beads using frequency scanning in magnetic frequency mixing technique magnetic fields, a stable phase information is gained. In this research, it is shown that the amplitude of the dominant mixing component is proportional to the amount of superparamagnetic beads inside a sample. Additionally, it is shown that the phase does not show this behaviour. Excitation frequency scans of different bead types were performed, showing different phases, without correlation to their diverse amplitudes. Two commercially available beads were selected and a determination of their amount in a mixture is performed as a demonstration for multiplex measurements. KW - frequency mixing magnetic detection KW - magnetic sandwich immunoassay KW - multiparametric immunoassays Y1 - 2019 U6 - https://doi.org/10.3390/s19112599 SN - 1424-8220 VL - 19 IS - 11 PB - MDPI CY - Basel ER - TY - PAT A1 - Salber, Wolfgang A1 - Pischinger, Martin A1 - Esch, Thomas A1 - Hagen, Jürgen T1 - Kaltstartverfahren für eine drosselfreie Mehrzylinder-Kolbenbrennkraftmaschine N2 - Die Erfindung betrifft ein Kaltstartverfahren für eine Mehrzylinder-Kolbenbrennkraftmaschine mit Anlasser und einer Motorsteuerung zur Ansteuerung von Kraftstoffeinspritzeinrichtungen, Zündung und voll variabel elektromagnetisch betätigbaren Gaswechselventilen an den einzelnen Zylindern, bei dem die Kurbelwelle über den Anlasser gedreht wird und zum Start für wenigstens einen Zylinder die dazugehörigen Gaswechselventile, die Kraftstoffeinspritzeinrichtung und die Zündung in einem vorgegebenen Taktzyklus angesteuert werden und zwar in den ersten Arbeitszyklen mit "Spätem Einlaß Öffnen". Y1 - 2000 N1 - Patent DE000019830974B4 2005.11.03 ER - TY - JOUR A1 - Achtsnicht, Stefan A1 - Neuendorf, Christian A1 - Faßbender, Tobias A1 - Nölke, Greta A1 - Offenhäusser, Andreas A1 - Krause, Hans-Joachim A1 - Schröper, Florian T1 - Sensitive and rapid detection of cholera toxin subunit B using magnetic frequency mixing detection JF - Plos One N2 - Cholera is a life-threatening disease caused by the cholera toxin (CT) as produced by some Vibrio cholerae serogroups. In this research we present a method which directly detects the toxin’s B subunit (CTB) in drinking water. For this purpose we performed a magnetic sandwich immunoassay inside a 3D immunofiltration column. We used two different commercially available antibodies to capture CTB and for binding to superparamagnetic beads. ELISA experiments were performed to select the antibody combination. The beads act as labels for the magnetic frequency mixing detection technique. We show that the limit of detection depends on the type of magnetic beads. A nonlinear Hill curve was fitted to the calibration measurements by means of a custom-written python software. We achieved a sensitive and rapid detection of CTB within a broad concentration range from 0.2 ng/ml to more than 700 ng/ml. Y1 - 2019 U6 - https://doi.org/10.1371/journal.pone.0219356 SN - 1932-6203 VL - 14 IS - 7 PB - Plos CY - San Francisco ER - TY - PAT A1 - Schmitz, Günter A1 - Schebitz, Michael A1 - Esch, Thomas T1 - Aus der Ruhelage selbstanziehender elektromagnetischer Aktuator N2 - Elektromagnetischer Aktuator zur Betätigung eines Stellgliedes (2), mit wenigstens einem Elektromagneten (4) und einem mit dem Stellglied (2) verbundenen Anker (3), der gegen die Kraft einer Rückstellfeder (6) aus seiner Ruhelage in Richtung auf den Elektromagneten (4) bewegbar ist, mit einer Rückstellfeder (6), die eine nicht lineare, bezogen auf die Ruhelage des Ankers (3) progressiv ansteigende Kennlinie aufweist. Y1 - 1997 N1 - Patent DE000019529152B4 2005.12.29 ER - TY - THES A1 - Achtsnicht, Stefan T1 - Multiplex-Magnetdetektion von superparamagnetischen Beads zur Identifizierung von Trinkwasserkontaminationen N2 - Die qualitative und quantitative Detektion von Zielsubstanzen innerhalb einer wässrigen Probe ist für viele Fragestellungen von Interesse, etwa bei der Detektion von Kontaminationen in Trinkwasser in Krisensituationen. Hierbei ist es nicht nur wichtig, dass Pathogene möglichst sensitiv detektiert werden können, sondern auch, dass die Analyse schnell erfolgt, um Betroffenen im Katastrophenfall zügig sicheres Trinkwasser zu Verfügung stellen zu können. Da bei einem solchen Szenario nicht von einer in der Nähe befindlichen funktionierenden Laborinfrastruktur ausgegangen werden kann, ist es wichtig, dass die Messung direkt vor Ort erfolgen kann. Im Rahmen dieser Arbeit wurde untersucht, ob eine derartige Schnellanalytik mithilfe von superparamagnetischen Beads (MBs) und der magnetischen Frequenzmischtechnik möglich ist. Dabei werden die MBs mit Hilfe von primären Antikörpern an die Zielsubstanz gebunden und mit sekundären Antikörpern an die Poren-Oberfläche eines Polyethylen-Filters fixiert (Sandwich-Immunoassay). So kann die Quantifizierung der Zielsubstanz auf eine magnetische Messung der immobilisierten MB-Marker zurückgeführt werden. Die magnetische Frequenzmischtechnik basiert auf der Anregung der Probe mit Magnetfeldern zweier verschiedener Frequenzen. Die durch die nichtlineare Magnetisierungsform der superparamagnetischen MBs entstehenden Mischfrequenzen werden typischerweise mithilfe einer zweistufigen Lock-in-Detektion analysiert (analoge Demodulation), die in einem Magnetreader als Handheldgerät realisiert wurde. Zusätzlich zu dieser Technik wurde das Prinzip der direkten Digitalisierung des gesamten Antwortsignals mit anschließender Fourier-Analyse der erzeugten Mischfrequenzen experimentell umgesetzt, um die Amplituden und Phasen mehrerer Mischfrequenzen simultan zu erfassen. Eine Möglichkeit zur Sensitivitätssteigerung ist die magnetische Aufkonzentration, indem vor der magnetischen Analyse eine Separation der MBs aus einem größeren Probenvolumen mittels magnetischem Feldgradienten durchgeführt wird. Zur Charakterisierung verschiedener kommerzieller MBs hinsichtlich ihrer magnetischen Separierbarkeit wurde ein Aufbau zur Messung ihrer magnetophoretischen Beweglichkeiten realisiert und ihre Geschwindigkeiten im Gradientenfeld mikroskopisch gemessen.Da eine Probe oftmals nicht nur auf eine einzige Zielsubstanz, sondern simultan auf mehrere verschiedene Pathogene hin untersucht werden soll, wurden verschiedene Ansätze entwickelt und getestet, die einen solchen multiparametrischen magnetischen Immunoassay ermöglichen. Einerseits wurde eine räumliche Separation der Bindungsbereiche für verschiedene Zielsubstanzen realisiert, die sequentiell ausgewertet werden können. Andererseits wurde die Unterscheidung von verschiedenen Zielsubstanzen anhand der Charakteristika der an sie gebundenen, verschieden funktionalisierten MB-Typen untersucht. Für eine solche Unterscheidung wurde zum einen die Anregefrequenz der magnetischen Frequenzmischtechnik während einer Messung variiert. Damit konnte gezeigt werden, dass sich verschiedene MB-Sorten anhand der Phase ihrer Frequenzmischsignale voneinander unterscheiden lassen. Weiterhin wurde gezeigt, dass sich der Signalverlauf einer binären Mischung zweier verschiedener MB-Typen als gradueller Übergang der Verläufe der beiden reinen MB-Lösungen ergibt. Eine weitere Analysemethode für einen multiparametrischen Immunoassay besteht darin, ein zusätzliches einstellbares statisches magnetisches Offsetfeld zu verwenden. Hierfür wurden mehrere Aufbauten auf Basis von Permanent- und Elektromagneten simuliert, konstruiert und charakterisiert. Mithilfe von Simulationen konnte gezeigt werden, dass eine auf diesem Verfahren beruhende Unterscheidung für MBs mit unterschiedlichen magnetischen Partikelmomenten möglich ist. Als direkte Anwendung des hier entwickelten Magnetreaders in Zusammenspiel mit der digitalen Demodulation wurde ein magnetischer Assay gegen die B-Untereinheit des Choleratoxins in Trinkwasser mit einem niedrigen Detektionslimit von 0,2 ng/ml demonstriert. N2 - The qualitative and quantitative detection of target substances in an aqueous sample is of interest for many questions, for example in the detection of contaminations in drinking water in crisis situations. It is not only important that pathogens can be detected with highest possible sensitivity, but also that the analysis is carried out quickly so that safe drinking water can be provided in the event of a disaster. During such a scenario one cannot rely on a functioning laboratory infrastructure nearby. Therefore it is important that the measurement can be carried out directly on site. Within the scope of this work, it was investigated whether such a quick analysis can be performed using superparamagnetic beads (MBs) and the magnetic frequency mixing technique. The MBs are bound to the target substance with the aid of primary antibodies and fixed to the pore surfaces of a polyethylene filter with secondary antibodies (sandwich immunoassay). The quantification of the target substance can thus be traced back to a magnetic measurement of the immobilized MB markers. The magnetic frequency mixing technique is based on the excitation of the sample with magnetic fields of two different frequencies. The mixing frequencies generated due to the non-linear shape of the magnetization of the superparamagnetic MBs are typically analyzed using a two-stage Lock-in detection (analog demodulation), which was implemented in a magnetic reader as a handheld device. In addition to this technique, the principle of direct digitization of the entire response signal with subsequent Fourier analysis of the generated mixing frequencies was experimentally implemented in order to simultaneously record the amplitudes and phases of several mixing frequencies. One possibility for increasing the sensitivity is magnetic concentration. In that case, the MBs are separated from a larger sample volume by means of a magnetic field gradient before the magnetic analysis. To characterize various commercial MBs with regard to their magnetic separability, a setup for measuring their magnetophoretic mobility was implemented and their velocities in the gradient field were measured with an optical microscope.Often, a sample has to be examined not only for a single target substance, but for several different pathogens simultaneously. Various approaches have been developed and tested which enable such a multiparametric magnetic immunoassay. On the one hand, a spatial separation of the binding areas for different target substances was realized, which can be evaluated sequentially. On the other hand, a distinction among different target substances based on the magnetic characteristics of their attached different MB types was examined. For this discrimination, the excitation frequency of the magnetic frequency mixing technology was varied during measurement. It is shown that different MB types can be distinguished from one another based on the phase of their frequency mixing signals. The signal curve of a binary mixture of two different MB types is obtained as a gradual transition of the curves of the two pure MB solutions. Another method of analysis for a multiparametric immunoassay is based on an additional adjustable static magnetic offset field. For this purpose, several setups based on permanent magnets and electromagnets were simulated, designed and characterized. The simulations show that a distinction based on this method is possible for MBs with different magnetic particle moments. As a direct application of the developed magnetic reader in conjunction with digital demodulation, a magnetic assay against the B subunit of cholera toxin in drinking water was demonstrated, and a low detection limit of 0.2 ng/ml was achieved. KW - Choleratoxin B KW - Trinkwassersicherheit KW - cholera toxin B KW - drinking water safety KW - magnetic frequency mixing technique Y1 - 2020 U6 - https://doi.org/10.18154/RWTH-2020-12052 N1 - Dissertation, RWTH Aachen University, 2020 ER - TY - JOUR A1 - Janus, Kevin Alexander A1 - Achtsnicht, Stefan A1 - Tempel, Laura A1 - Drinic, Aleksaner A1 - Kopp, Alexander A1 - Keusgen, Michael A1 - Schöning, Michael Josef T1 - Influence of fibroin membrane composition and curing parameters on the performance of a biodegradable enzymatic biosensor manufactured from Silicon-Free Carbon JF - Physica status solidi : pss. A, Applications and materials science N2 - Herein, fibroin, polylactide (PLA), and carbon are investigated for their suitability as biocompatible and biodegradable materials for amperometric biosensors. For this purpose, screen-printed carbon electrodes on the biodegradable substrates fibroin and PLA are modified with a glucose oxidase membrane and then encapsulated with the biocompatible material Ecoflex. The influence of different curing parameters of the carbon electrodes on the resulting biosensor characteristics is studied. The morphology of the electrodes is investigated by scanning electron microscopy, and the biosensor performance is examined by amperometric measurements of glucose (0.5–10 mM) in phosphate buffer solution, pH 7.4, at an applied potential of 1.2 V versus a Ag/AgCl reference electrode. Instead of Ecoflex, fibroin, PLA, and wound adhesive are tested as alternative encapsulation compounds: a series of swelling tests with different fibroin compositions, PLA, and Ecoflex has been performed before characterizing the most promising candidates by chronoamperometry. Therefore, the carbon electrodes are completely covered with the particular encapsulation material. Chronoamperometric measurements with H2O2 concentrations between 0.5 and 10 mM enable studying the leakage current behavior. KW - amperometric biosensors KW - biocompatible KW - biodegradabl KW - encapsulation materials KW - fibroin Y1 - 2023 U6 - https://doi.org/10.1002/pssa.202300081 SN - 1862-6300 (Print) SN - 1862-6319 (Online) N1 - Corresponding author: Michael J. Schöning VL - 220 IS - 22 PB - Wiley-VCH CY - Weinheim ER - TY - JOUR A1 - Heieis, Jule A1 - Böcker, Jonas A1 - D'Angelo, Olfa A1 - Mittag, Uwe A1 - Albracht, Kirsten A1 - Schönau, Eckhard A1 - Meyer, Andreas A1 - Voigtmann, Thomas A1 - Rittweger, Jörn T1 - Curvature of gastrocnemius muscle fascicles as function of muscle–tendon complex length and contraction in humans JF - Physiological Reports N2 - It has been shown that muscle fascicle curvature increases with increasing contraction level and decreasing muscle–tendon complex length. The analyses were done with limited examination windows concerning contraction level, muscle–tendon complex length, and/or intramuscular position of ultrasound imaging. With this study we aimed to investigate the correlation between fascicle arching and contraction, muscle–tendon complex length and their associated architectural parameters in gastrocnemius muscles to develop hypotheses concerning the fundamental mechanism of fascicle curving. Twelve participants were tested in five different positions (90°/105°*, 90°/90°*, 135°/90°*, 170°/90°*, and 170°/75°*; *knee/ankle angle). They performed isometric contractions at four different contraction levels (5%, 25%, 50%, and 75% of maximum voluntary contraction) in each position. Panoramic ultrasound images of gastrocnemius muscles were collected at rest and during constant contraction. Aponeuroses and fascicles were tracked in all ultrasound images and the parameters fascicle curvature, muscle–tendon complex strain, contraction level, pennation angle, fascicle length, fascicle strain, intramuscular position, sex and age group were analyzed by linear mixed effect models. Mean fascicle curvature of the medial gastrocnemius increased with contraction level (+5 m−1 from 0% to 100%; p = 0.006). Muscle–tendon complex length had no significant impact on mean fascicle curvature. Mean pennation angle (2.2 m−1 per 10°; p < 0.001), inverse mean fascicle length (20 m−1 per cm−1; p = 0.003), and mean fascicle strain (−0.07 m−1 per +10%; p = 0.004) correlated with mean fascicle curvature. Evidence has also been found for intermuscular, intramuscular, and sex-specific intramuscular differences of fascicle curving. Pennation angle and the inverse fascicle length show the highest predictive capacities for fascicle curving. Due to the strong correlations between pennation angle and fascicle curvature and the intramuscular pattern of curving we suggest for future studies to examine correlations between fascicle curvature and intramuscular fluid pressure. KW - biomechanics KW - connective tissue KW - physiology KW - ultrasound Y1 - 2023 U6 - https://doi.org/10.14814/phy2.15739 SN - 2051-817X VL - 11 IS - 11 SP - e15739, Seite 1-11 PB - Wiley ER - TY - CHAP A1 - Schopen, Oliver A1 - Shabani, Bahman A1 - Esch, Thomas A1 - Kemper, Hans A1 - Shah, Neel ED - Rahim, S.A. ED - As'arry, A. ED - Zuhri, M.Y.M. ED - Harmin, M.Y. ED - Rezali, K.A.M. ED - Hairuddin, A.A. T1 - Quantitative evaluation of health management designs for fuel cell systems in transport vehicles T2 - 2nd UNITED-SAIG International Conference Proceedings N2 - Focusing on transport vehicles, mainly with regard to aviation applications, this paper presents compilation and subsequent quantitative evaluation of methods aimed at building an optimum integrated health management solution for fuel cell systems. The methods are divided into two different main types and compiled in a related scheme. Furthermore, different methods are analysed and evaluated based on parameters specific to the aviation context of this study. Finally, the most suitable method for use in fuel cell health management systems is identified and its performance and suitability is quantified. KW - aviation application KW - health management systems KW - fuel cell systems Y1 - 2022 N1 - 2nd UNITED-SAIG International Conference, 23-24 May 2022, Putrajaya, Malaysia SP - 1 EP - 3 ER - TY - CHAP A1 - Schopen, Oliver A1 - Kemper, Hans A1 - Esch, Thomas T1 - Development of a comparison methodology and evaluation matrix for electrically driven compressors in ICE and FC T2 - Proceedings of the 1st UNITED – Southeast Asia Automotive Interest Group (SAIG) International Conference N2 - In addition to electromobility and alternative drive systems, a focus is set on electrically driven compressors (EDC), with a high potential for increasing the efficiency of internal combustion engines (ICE) and fuel cells [01]. The primary objective is to increase the ICE torque, provided independently of the ICE speed by compressing the intake air and consequently the ICE filling level supported by the compressor. For operation independent from the ICE speed, the EDC compressor is decoupled from the turbine by using an electric compressor motor (CM) instead of the turbine. ICE performances can be increased by the use of EDC where individual compressor parameters are adapted to the respective application area [02] [03]. This task contains great challenges, increased by demands with regard to pollutant reduction while maintaining constant performance and reduced fuel consumption. The FH-Aachen is equipped with an EDC test bench which enables EDC-investigations in various configurations and operating modes. Characteristic properties of different compressors can be determined, which build the basis for a comparison methodology. Subject of this project is the development of a comparison methodology for EDC with an associated evaluation method and a defined overall evaluation method. For the application of this comparison methodology, corresponding series of measurements are carried out on the EDC test bench using an appropriate test device. KW - electro mobility KW - fuel cell KW - internal combustion engine KW - electrically driven compressors Y1 - 2021 SN - 978-3-902103-94-9 N1 - 1st UNITED-SAIG International Conference, 21-22 APR 2021, Chulalongkorn University, Thailand SP - 45 EP - 46 PB - FH Joanneum CY - Graz ER - TY - CHAP A1 - Veettil, Yadu Krishna Morassery A1 - Rakshit, Shantam A1 - Schopen, Oliver A1 - Kemper, Hans A1 - Esch, Thomas A1 - Shabani, Bahman ED - Bin Abdollah, Mohd Fadzli ED - Amiruddin, Hilmi ED - Singh, Amrik Singh Phuman ED - Munir, Fudhail Abdul ED - Ibrahim, Asriana T1 - Automated Control System Strategies to Ensure Safety of PEM Fuel Cells Using Kalman Filters T2 - Proceedings of the 7th International Conference and Exhibition on Sustainable Energy and Advanced Materials (ICE-SEAM 2021), Melaka, Malaysia N2 - Having well-defined control strategies for fuel cells, that can efficiently detect errors and take corrective action is critically important for safety in all applications, and especially so in aviation. The algorithms not only ensure operator safety by monitoring the fuel cell and connected components, but also contribute to extending the health of the fuel cell, its durability and safe operation over its lifetime. While sensors are used to provide peripheral data surrounding the fuel cell, the internal states of the fuel cell cannot be directly measured. To overcome this restriction, Kalman Filter has been implemented as an internal state observer. Other safety conditions are evaluated using real-time data from every connected sensor and corrective actions automatically take place to ensure safety. The algorithms discussed in this paper have been validated thorough Model-in-the-Loop (MiL) tests as well as practical validation at a dedicated test bench. KW - control system KW - PEM fuel cells KW - Kalman filter Y1 - 2022 SN - 978-981-19-3178-9 SN - 978-981-19-3179-6 (E-Book) U6 - https://doi.org/10.1007/978-981-19-3179-6_55 SN - 2195-4356 N1 - 7th International Conference and Exhibition on Sustainable Energy and Advanced Material (ICE-SEAM 2021), Universiti Teknikal Malaysia Melaka (UTeM), Malaysia, in association with the Universitas Sebelas Maret (UNS), Indonesia, 23 November 2021 SP - 296 EP - 299 PB - Springer Nature CY - Singapore ER - TY - CHAP A1 - Tamaldin, Noreffendy A1 - Mansor, Muhd Rizuan A1 - Mat Yamin, Ahmad Kamal A1 - Bin Abdollah, Mohd Fazli A1 - Esch, Thomas A1 - Tonoli, Andrea A1 - Reisinger, Karl Heinz A1 - Sprenger, Hanna A1 - Razuli, Hisham ED - Bin Abdollah, Mohd Fadzli ED - Amiruddin, Hilmi ED - Singh, Amrik Singh Phuman ED - Munir, Fudhail Abdul ED - Ibrahim, Asriana T1 - Development of UTeM United Future Fuel Design Training Center Under Erasmus+ United Program T2 - Proceedings of the 7th International Conference and Exhibition on Sustainable Energy and Advanced Materials (ICE-SEAM 2021), Melaka, Malaysia N2 - The industrial revolution IR4.0 era have driven many states of the art technologies to be introduced especially in the automotive industry. The rapid development of automotive industries in Europe have created wide industry gap between European Union (EU) and developing countries such as in South-East Asia (SEA). Indulging this situation, FH Joanneum, Austria together with European partners from FH Aachen, Germany and Politecnico Di Torino, Italy is taking initiative to close the gap utilizing the Erasmus+ United grant from EU. A consortium was founded to engage with automotive technology transfer using the European ramework to Malaysian, Indonesian and Thailand Higher Education Institutions (HEI) as well as automotive industries. This could be achieved by establishing Engineering Knowledge Transfer Unit (EKTU) in respective SEA institutions guided by the industry partners in their respective countries. This EKTU could offer updated, innovative, and high-quality training courses to increase graduate’s employability in higher education institutions and strengthen relations between HEI and the wider economic and social environment by addressing Universityindustry cooperation which is the regional priority for Asia. It is expected that, the Capacity Building Initiative would improve the quality of higher education and enhancing its relevance for the labor market and society in the SEA partners. The outcome of this project would greatly benefit the partners in strong and complementary partnership targeting the automotive industry and enhanced larger scale international cooperation between the European and SEA partners. It would also prepare the SEA HEI in sustainable partnership with Automotive industry in the region as a mean of income generation in the future. KW - Erasmus+ United KW - technology transfer KW - UTeM Engineering Knowledge Transfer Unit KW - Malaysian automotive industry Y1 - 2022 SN - 978-981-19-3178-9 SN - 978-981-19-3179-6 (E-Book) U6 - https://doi.org/10.1007/978-981-19-3179-6_50 SN - 2195-4356 N1 - 7th International Conference and Exhibition on Sustainable Energy and Advanced Material (ICE-SEAM 2021), Universiti Teknikal Malaysia Melaka (UTeM), Malaysia, in association with the Universitas Sebelas Maret (UNS), Indonesia, 23 November 2021 SP - 274 EP - 278 PB - Springer Nature CY - Singapore ER - TY - CHAP A1 - Tamaldin, Noreffendy A1 - Esch, Thomas A1 - Tonoli, Andrea A1 - Reisinger, Karl Heinz A1 - Sprenger, Hanna A1 - Razuli, Hisham T1 - ERASMUS+ United CBHE Automotive International Collaboration from European to South East Asia T2 - Proceedings of the 2nd African International Conference on Industrial Engineering and Operations Management N2 - The industrial revolution especially in the IR4.0 era have driven many states of the art technologies to be introduced. The automotive industry as well as many other key industries have also been greatly influenced. The rapid development of automotive industries in Europe have created wide industry gap between European Union (EU) and developing countries such as in South East Asia (SEA). Indulging this situation, FH JOANNEUM, Austria together with European partners from FH Aachen, Germany and Politecnico di Torino, Italy are taking initiative to close down the gap utilizing the Erasmus+ United Capacity Building in Higher Education grant from EU. A consortium was founded to engage with automotive technology transfer using the European framework to Malaysian, Indonesian and Thailand Higher Education Institutions (HEI) as well as automotive industries in respective countries. This could be achieved by establishing Engineering Knowledge Transfer Unit (EKTU) in respective SEA institutions guided by the industry partners in their respective countries. This EKTU could offer updated, innovative and high-quality training courses to increase graduate’s employability in higher education institutions and strengthen relations between HEI and the wider economic and social environment by addressing University-industry cooperation which is the regional priority for Asia. It is expected that, the Capacity Building Initiative would improve the quality of higher education and enhancing its relevance for the labor market and society in the SEA partners. The outcome of this project would greatly benefit the partners in strong and complementary partnership targeting the automotive industry and enhanced larger scale international cooperation between the European and SEA partners. It would also prepare the SEA HEI in sustainable partnership with Automotive industry in the region as a mean of income generation in the future. KW - European Framework and South East Asia KW - Technology Transfer KW - Capacity Building Higher Education KW - Malaysian Automotive Industry Y1 - 2020 SN - 978-1-7923-6123-4 SN - 2169-8767 N1 - 2nd African International Conference on Industrial Engineering and Operations Management; Harare, Zimbabwe, December 7-10, 2020 SP - 2970 EP - 2972 PB - IEOM Society International CY - Southfield ER - TY - CHAP A1 - Kreyer, Jörg A1 - Esch, Thomas T1 - Simulation Tool for Predictive Control Strategies for an ORCSystem in Heavy Duty Vehicles T2 - European GT Conference 2017 N2 - Scientific questions - How can a non-stationary heat offering in the commercial vehicle be used to reduce fuel consumption? - Which potentials offer route and environmental information among with predicted speed and load trajectories to increase the efficiency of a ORC-System? Methods - Desktop bound holistic simulation model for a heavy duty truck incl. an ORC System - Prediction of massflows, temperatures and mixture quality (AFR) of exhaust gas Y1 - 2017 N1 - European GT Conference 2017, 9.-10. Oktober 2017, Frankfurt a.M. ER - TY - RPRT A1 - Esch, Thomas A1 - Funke, Harald A1 - Roosen, Petra T1 - SIoBiA – Safety Implications of Biofuels in Aviation N2 - Biofuels potentially interesting also for aviation purposes are predominantly liquid fuels produced from biomass. The most common biofuels today are biodiesel and bioethanol. Since diesel engines are rather rare in aviation this survey is focusing on ethanol admixed to gasoline products. The Directive 2003/30/EC of the European Parliament and the Council of May 8th 2003 on the promotion of the use of biofuels or other renewable fuels for transport encourage a growing admixture of biogenic fuel components to fossil automotive gasoline. Some aircraft models equipped with spark ignited piston engines are approved for operation with automotive gasoline, frequently called “MOGAS” (motor gasoline). The majority of those approvals is limited to MOGAS compositions that do not contain methanol or ethanol beyond negligible amounts. In the past years (bio-)MTBE or (bio-)ETBE have been widely used as blending component of automotive gasoline whilst the usage of low-molecular alcohols like methanol or ethanol has been avoided due to the handling problems especially with regard to the strong affinity for water. With rising mandatory bio-admixtures the conversion of the basic biogenic ethanol to ETBE, causing a reduction of energetic payoff, becomes more and more unattractive. Therefore the direct ethanol admixture is accordingly favoured. Due to the national enforcements of the directive 2003/30/EC more oxygenates produced from organic materials like bioethanol have started to appear in automotive gasolines already. The current fuel specification EN 228 already allows up to 3 % volume per volume (v/v) (bio-)methanol or up to 5 % v/v (bio-)ethanol as fuel components. This is also roughly the amount of biogenic components to comply with the legal requirements to avoid monetary penalties for producers and distributors of fuels. Since automotive fuel is cheaper than the common aviation gasoline (AVGAS), creates less problems with lead deposits in the engine, and in general produces less pollutants it is strongly favoured by pilots. But being designed for a different set of usage scenarios the use of automotive fuel with low molecular alcohols for aircraft operation may have adverse effects in aviation operation. Increasing amounts of ethanol admixtures impose various changes in the gasoline’s chemical and physical properties, some of them rather unexpected and not within the range of flight experiences even of long-term pilots. Y1 - 2010 N1 - Analysis of the safety implications of the use of biofuels (ethanol admixture) for piston engines and general aviation aircraft and assessment of potential environmental benefits. PB - EASA CY - Köln ER - TY - JOUR A1 - Esch, Thomas T1 - Trends in commercial vehicle powertrains JF - ATZautotechnology N2 - Low emission zones and truck bans, the rising price of diesel and increases in road tolls: all of these factors are putting serious pressure on the transport industry. Commercial vehicle manufacturers and their suppliers are in the process of identifying new solutions to these challenges as part of their efforts to meet the EEV (enhanced environmentally friendly vehicle) limits, which are currently the most robust European exhaust and emissions standards for trucks and buses. KW - European Transient Cycle KW - Common Rail Injection System KW - Commercial Vehicle KW - Selective Catalytic Reduction KW - Diesel Engine Y1 - 2010 U6 - https://doi.org/10.1007/BF03247185 SN - 2192-886X VL - 2010 IS - 10 SP - 26 EP - 31 PB - Vieweg & Sohn CY - Wiesbaden ER - TY - CHAP A1 - Kemper, Hans A1 - Hellenbroich, Gereon A1 - Esch, Thomas T1 - Concept of an innovative passenger-car hybrid drive for European driving conditions T2 - Hybrid vehicles and energy management : 6th symposium ; 18th and 19th February 2009, Stadthalle Braunschweig N2 - The downsizing of spark ignition engines in conjunction with turbocharging is considered to be a promising method for reducing CO₂ emissions. Using this concept, FEV has developed a new, highly efficient drivetrain to demonstrate fuel consumption reduction and drivability in a vehicle based on the Ford Focus ST. The newly designed 1.8L turbocharged gasoline engine incorporates infinitely variable intake and outlet control timing and direct fuel injection utilizing piezo injectors centrally located. In addition, this engine uses a prototype FEV engine control system, with software that was developed and adapted entirely by FEV. The vehicle features a 160 kW engine with a maximum mean effective pressure of 22.4 bar and 34 % savings in simulated fuel consumption. During the first stage, a new electrohydraulically actuated hybrid transmission with seven forward gears and one reverse gear and a single dry starting clutch will be integrated. The electric motor of the hybrid is directly connected to the gear set of the transmission. Utilizing the special gear set layout, the electric motor can provide boost during a change of gears, so that there is no interruption in traction. Therefore, the transmission system combines the advantages of a double clutch controlled gear change (gear change without an interruption in traction) with the efficient, cost-effective design of an automated manual transmission system. Additionally, the transmission provides a purely electric drive system and the operation of an air-conditioning compressor during the engine stop phases. One other alternative is through the use of CAI (Controlled Auto Ignition), which incorporates a process developed by FEV for controlled compression ignition. Y1 - 2009 SN - 978-3-937655-20-8 SP - 264 EP - 287 PB - Gesamtzentrum für Verkehr (GZVB) CY - Braunschweig ER - TY - CHAP A1 - Funke, Harald A1 - Esch, Thomas A1 - Roosen, Peter ED - Bartz, Wilfried J. T1 - Using motor gasoline for aircrafts - coping with growing bio-fuel-caused risks by understanding cause-effect relationship T2 - Fuels 2009 : mineral oil based and alternative fuels ; 7th international colloquium ; January 14 - 15, 2009 N2 - The utilisation of vehicle-oriented gasoline in general aviation is very desirable for both ecological and economical reasons, as well as for general considerations of availability. As of today vehicle fuels may be used if the respective engine and cell are certified for such an operation. For older planes a supplementary technical certificate is provided for gasoline mixtures with less than 1 % v/v ethanol only, though. Larger admixtures of ethanol may lead to sudden engine malfunction and should be considered as considerable security risks. Major problems are caused by the partially ethanol non-withstanding materials, a necessarily changed stochiometric adjustment of the engine for varying ethanol shares and the tendency for phase separation in the presence of absorbed water. The concepts of the flexible fuel vehicles are only partially applicable in the view of air security. Y1 - 2009 SN - 978-3-924813-75-8 SP - 237 EP - 244 PB - Technische Akademie Esslingen (TAE) CY - Ostfildern ER - TY - CHAP A1 - Weiss, Alexander A1 - Abanteriba, Sylvester A1 - Esch, Thomas T1 - Investigation of Flow Separation Inside a Conical Rocket Nozzle With the Aid of an Annular Cross Flow T2 - Proceedings of the ASME/JSME 2007 5th Joint Fluids Engineering Conference. Volume 1: Symposia, Parts A and B N2 - Flow separation is a phenomenon that occurs in all kinds of supersonic nozzles sometimes during run-up and shut-down operations. Especially in expansion nozzles of rocket engines with large area ratio, flow separation can trigger strong side loads that can damage the structure of the nozzle. The investigation presented in this paper seeks to establish measures that may be applied to alter the point of flow separation. In order to achieve this, a supersonic nozzle was placed at the exit plane of the conical nozzle. This resulted in the generation of cross flow surrounding the core jet flow from the conical nozzle. Due to the entrainment of the gas stream from the conical nozzle the pressure in its exit plane was found to be lower than that of the ambient. A Cold gas instead of hot combustion gases was used as the working fluid. A mathematical simulation of the concept was validated by experiment. Measurements confirmed the simulation results that due to the introduction of a second nozzle the pressure in the separated region of the conical nozzle was significantly reduced. It was also established that the boundary layer separation inside the conical nozzle was delayed thus allowing an increased degree of overexpansion. The condition established by the pressure measurements was also demonstrated qualitatively using transparent nozzle configurations. Y1 - 2007 SN - 0-7918-4288-6 U6 - https://doi.org/10.1115/FEDSM2007-37387 N1 - Proceedings of the ASME/JSME 2007 5th Joint Fluids Engineering Conference. Volume 1: Symposia, Parts A and B. San Diego, California, USA. July 30–August 2, 2007 SP - 1861 EP - 1871 PB - American Society of Mechanical Engineers (ASME) CY - New York ER - TY - CHAP A1 - Huth, Thomas A1 - Elsen, Olaf A1 - Hartwig, Christoph A1 - Esch, Thomas T1 - Innovative modular valve trains for 2015 - logistic benefits by EMVT T2 - IFAC Proceedings Volumes, Volume 39, Issue 3 N2 - In this paper the way to a 5-day-car with respect to a modular valve train systems for spark ignited combustion engines is shown. The necessary product diversity is shift from mechanical or physical components to software components. Therefore, significant improvements of logistic indicators are expected and shown. The working principle of a camless cylinder head with respect to an electromagnetical valve train (EMVT) is explained and it is demonstrated that shifting physical diversity to software is feasible. The future design of combustion engine systems including customisation can be supported by a set of assistance tools which is shown exemplary. Y1 - 2006 U6 - https://doi.org/10.3182/20060517-3-FR-2903.00172 N1 - Part of special issue "12th IFAC Symposium on Information Control Problems in Manufacturing" SP - 315 EP - 320 PB - Elsevier CY - Amsterdam ER - TY - JOUR A1 - Rhoden, Imke A1 - Ball, Christopher Stephen A1 - Grajewski, Matthias A1 - Kuckshinrich, Wilhelm T1 - Reverse engineering of stakeholder preferences – A multi-criteria assessment of the German passenger car sector JF - Renewable and Sustainable Energy Reviews N2 - Germany is a frontrunner in setting frameworks for the transition to a low-carbon system. The mobility sector plays a significant role in this shift, affecting different people and groups on multiple levels. Without acceptance from these stakeholders, emission targets are out of reach. This research analyzes how the heterogeneous preferences of various stakeholders align with the transformation of the mobility sector, looking at the extent to which the German transformation paths are supported and where stakeholders are located. Under the research objective of comparing stakeholders' preferences to identify which car segments require additional support for a successful climate transition, a status quo of stakeholders and car performance criteria is the foundation for the analysis. Stakeholders' hidden preferences hinder the derivation of criteria weightings from stakeholders; therefore, a ranking from observed preferences is used. This study's inverse multi-criteria decision analysis means that weightings can be predicted and used together with a recalibrated performance matrix to explore future preferences toward car segments. Results show that stakeholders prefer medium-sized cars, with the trend pointing towards the increased potential for alternative propulsion technologies and electrified vehicles. These insights can guide the improved targeting of policy supporting the energy and mobility transformation. Additionally, the method proposed in this work can fully handle subjective approaches while incorporating a priori information. A software implementation of the proposed method completes this work and is made publicly available. KW - Regionalization KW - Multi-criteria decision analysis KW - Preference assessment KW - E-Mobility KW - Mobility transition Y1 - 2023 U6 - https://doi.org/10.1016/j.rser.2023.113352 SN - 1364-0321 VL - 181 IS - July 2023 SP - Article number: 113352 PB - Elsevier CY - Amsterdam ER - TY - PAT A1 - Pischinger, Martin A1 - Esch, Thomas A1 - Duesmann, Klaus T1 - Elektromagnetischer Aktuator mit gelenkig abgestützter Rückstellfeder N2 - Die Erfindung betrifft einen elektromagnetischen Aktuator zur Betätigung eines Stellgliedes (7) mit wenigstens einem gesteuert bestrombaren Elektromagneten (1, 2) und einem mit dem Stellglied (7) in Wirkverbindung stehenden Anker (5), der bei Bestromung des Elektromagneten (1, 2) gegen die Kraft wenigstens einer an einem Gehäuse (12) abgestützten Rückstellfeder (10) an der Polfläche (3, 4) des Elektromagneten (1, 2) zur Anlage kommt, und daß zumindest der Anker (5) über eine sphärische Gelenkanordnung (11) auf der Rückstellfeder (10) abgestützt ist. Y1 - 2023 N1 - Patent DE000019822907B4 2006.07.27 ER - TY - CHAP A1 - Stollenwerk, Dominik A1 - Franzke, Till A1 - Maurer, Florian A1 - Reinkensmeier, Sebastian A1 - Kim, Franken A1 - Tambornino, Philipp A1 - Haas, Florian A1 - Rieke, Christian A1 - Hermanuz, Andreas A1 - Borchert, Jörg A1 - Ritz, Thomas A1 - Sander, Volker ED - Proff, Heike T1 - Smarte Ladesäulen : Netz- und Marktdienliches öffentliches Laden T2 - Towards the New Normal in Mobility : Technische und betriebswirtschaftliche Aspekte N2 - Stand 01.01.2022 sind in Deutschland 618.460 elektrisch angetriebene KFZ zugelassen. Insgesamt sind derzeit 48.540.878 KFZ zugelassen, was einer Elektromobilitätsquote von ca. 1,2 % entspricht. Derzeit werden Elektromobile über Ladestationen oder Steckdosen mit dem Stromnetz verbunden und üblicherweise mit der vollen Ladekapazität des Anschlusses aufgeladen, bis das Batteriemanagementsystem des Fahrzeugs abhängig vom Ladezustand der Batterie die Ladeleistung reduziert. Y1 - 2023 SN - 978-3-658-39437-0 (Print) SN - 978-3-658-39438-7 (Online) U6 - https://doi.org/10.1007/978-3-658-39438-7_18 SP - 287 EP - 304 PB - Springer Gabler CY - Wiesbaden ER - TY - JOUR A1 - Falkenberg, Fabian A1 - Voß, Leonie A1 - Bott, Michael A1 - Bongaerts, Johannes A1 - Siegert, Petra T1 - New robust subtilisins from halotolerant and halophilic Bacillaceae JF - Applied Microbiology and Biotechnology N2 - The aim of the present study was the characterisation of three true subtilisins and one phylogenetically intermediate subtilisin from halotolerant and halophilic microorganisms. Considering the currently growing enzyme market for efficient and novel biocatalysts, data mining is a promising source for novel, as yet uncharacterised enzymes, especially from halophilic or halotolerant Bacillaceae, which offer great potential to meet industrial needs. Both halophilic bacteria Pontibacillus marinus DSM 16465ᵀ and Alkalibacillus haloalkaliphilus DSM 5271ᵀ and both halotolerant bacteria Metabacillus indicus DSM 16189 and Litchfieldia alkalitelluris DSM 16976ᵀ served as a source for the four new subtilisins SPPM, SPAH, SPMI and SPLA. The protease genes were cloned and expressed in Bacillus subtilis DB104. Purification to apparent homogeneity was achieved by ethanol precipitation, desalting and ion-exchange chromatography. Enzyme activity could be observed between pH 5.0–12.0 with an optimum for SPPM, SPMI and SPLA around pH 9.0 and for SPAH at pH 10.0. The optimal temperature for SPMI and SPLA was 70 °C and for SPPM and SPAH 55 °C and 50 °C, respectively. All proteases showed high stability towards 5% (w/v) SDS and were active even at NaCl concentrations of 5 M. The four proteases demonstrate potential for future biotechnological applications. KW - Biotechnological application KW - Bacillaceae KW - Subtilisin KW - Subtilases KW - Halotolerant protease Y1 - 2023 U6 - https://doi.org/10.1007/s00253-023-12553-w SN - 1432-0614 N1 - Corresponding author: Petra Siegert VL - 107 SP - 3939 EP - 3954 PB - Springer Nature CY - Berlin ER - TY - BOOK A1 - Sept, Marcel A1 - Zillinger, Christina A1 - Wiechert, Johanna A1 - Thelen, Marius ED - Kroll-Ludwigs, Kathrin ED - Bassen-Metz, Yasmine ED - Bernecker, Andreas ED - Eggert, Mathias ED - Fritz, Thomas ED - Golland, Alexander ED - Höhne, Tim ED - Tran, Duc Hung ED - Vogt, Jürgen T1 - Aachener Online-Schriften Wirtschaft und Recht. Band 6. 01/2023 N2 - Inhaltsverzeichnis - Bachelorarbeiten 1. Zukunft der Rente – Kann eine Erwerbstätigenversicherung das demografische Problem nachhaltig lösen? - Marcel Sept | Seite 4-73 2. Die versammlungsgebundenen Aktionärsrechte in der neuen virtuellen Hauptversammlung – eine Bewertung aus Unternehmer- und Aktionärssicht - Christina Zillinger | Seite 74-130 3. Praxisleitfaden für den Arbeitgeber zum gesetzlichen Sonderkündigungsschutz – Was muss der Arbeitgeber tun, um durch Gesetz besonders geschützten Arbeitnehmern kündigen zu können? - Johanna Wiechert | Seite 131-195 4. Die Steuervergünstigung bei Umstrukturierungen im Konzern nach § 6a GrEStG im Lichte der aktuellen Rechtsprechung - Marius Thelen | Seite 196-265 T3 - Aachener Online-Schriften Wirtschaft und Recht - 6 Y1 - 2023 PB - FH Aachen / Fachbereich Wirtschaftswissenschaften CY - Aachen ER - TY - GEN A1 - Eickmann, Matthias A1 - Esch, Thomas A1 - Funke, Harald A1 - Abanteriba, Sylvester A1 - Roosen, Petra T1 - Biofuels in Aviation – Safety Implications of Bio-Ethanol Usage in General Aviation Aircraft N2 - Up in the clouds and above fuels and construction materials must be very carefully selected to ensure a smooth flight and touchdown. Out of around 38,000 single and dual-engined propeller aeroplanes, roughly a third are affected by a new trend in the fuel sector that may lead to operating troubles or even emergency landings: The admixture of bio-ethanol to conventional gasoline. Experiences with these fuels may be projected to alternative mixtures containing new components. Y1 - 2014 N1 - 2. International Conference of the Cluster of Excellence Tailor-Made Fuels from Biomass, Aachen 2013 ER - TY - JOUR A1 - Möhren, Felix A1 - Bergmann, Ole A1 - Janser, Frank A1 - Braun, Carsten T1 - On the influence of elasticity on propeller performance: a parametric study JF - CEAS Aeronautical Journal N2 - The aerodynamic performance of propellers strongly depends on their geometry and, consequently, on aeroelastic deformations. Knowledge of the extent of the impact is crucial for overall aircraft performance. An integrated simulation environment for steady aeroelastic propeller simulations is presented. The simulation environment is applied to determine the impact of elastic deformations on the aerodynamic propeller performance. The aerodynamic module includes a blade element momentum approach to calculate aerodynamic loads. The structural module is based on finite beam elements, according to Timoshenko theory, including moderate deflections. Several fixed-pitch propellers with thin-walled cross sections made of both isotropic and non-isotropic materials are investigated. The essential parameters are varied: diameter, disc loading, sweep, material, rotational, and flight velocity. The relative change of thrust between rigid and elastic blades quantifies the impact of propeller elasticity. Swept propellers of large diameters or low disc loadings can decrease the thrust significantly. High flight velocities and low material stiffness amplify this tendency. Performance calculations without consideration of propeller elasticity can lead to decreased efficiency. To avoid cost- and time-intense redesigns, propeller elasticity should be considered for swept planforms and low disc loadings. KW - Propeller KW - Finite element method KW - Blade element method KW - Propeller elasticity KW - Aeroelasticity Y1 - 2023 U6 - https://doi.org/10.1007/s13272-023-00649-y SN - 1869-5590 (Online) SN - 1869-5582 (Print) N1 - Corresponding author: Felix Möhren VL - 14 SP - 311 EP - 323 PB - Springer Nature CY - Berlin ER - TY - THES A1 - Hoffmann, Jan-Peter T1 - Schlüter Projekt X N2 - Schlüter Projekt X ist die fiktive Reanimation des Traktorenherstellers Schlüter. Dabei geht es darum, auf Basis der originalen Traktoren eine moderne Maschine zu entwerfen, welche die bewährte und beliebte Formsprache mit moderner Technologie und aktuellen Funktionen verbindet, um den Anforderungen der modernen Landwirtschaft gerecht zu werden. Dazu wurde Projekt X stark modular aufgebaut. Die Fahrzeugkabine lässt sich um 180° drehen und gegebenenfalls durch ein vollkommen autonomes Modul austauschen. Die Reifen lassen sich bei Bedarf durch Ketten ersetzen. Projekt X wird elektronisch angetrieben, zur Vermeidung langer Ladezeiten lässt sich der gesamte Akkublock in der Motorhaube austauschen. KW - Traktor KW - Landwirtschaft KW - Landwirt KW - Schlüter KW - Schlepper Y1 - 2023 PB - FH Aachen CY - Aachen ER - TY - THES A1 - Vogt, Linda T1 - Bambus als Baumaterial : eine nachhaltige Alternative zu herkömmlichen Rohstoffen? N2 - "Das Editorial greift die Thematik der aktuellen Klimakrise auf und beleuchtet diese im Bereich des nachhaltigen Bauens. Denn durch das stetige Wachstum der menschlichen Bevölkerung in Kombination mit dem Anstieg des Pro-Kopf-Verbrauchs werden globale Ressourcen immer stärker belastet. Ziel der Arbeit ist es, die aktuelle Situation des Klimawandels aus einer Perspektive zu betrachten, der sich die meisten nicht bewusst sind. Denn besonders das Bauwesen trägt einen erheblichen Anteil zum Klimawandel bei. In der Publikation werden Texte zum Thema Klimawandel und nachhaltiges Bauen behandelt sowie fotografische Anwendungsbeispiele im Bereich der Bambus-Architektur gezeigt. Das Projekt präsentiert Lösungsansätze, wie herkömmliche Rohstoffe durch verarbeiteten Bambus ergänzt bzw. ersetzt werden können. Dadurch kann ein entscheidender Beitrag zur Bekämpfung des Klimawandels geleistet werden. Bambus bietet dahingehend viele Möglichkeiten. Bei richtiger Verarbeitung vereint er viele der geforderten Ansprüche nachhaltigen Bauens. Der Rohstoff ist stark und flexibel zugleich. Er bindet Kohlenstoff, reinigt kontaminierte Böden, beugt Erosionen vor und weist eine nahezu negative CO2-Bilanz auf. Wie kann es gelingen, diesen Rohstoff in westlichen Ländern als Baumaterial zu integrieren?" KW - Klimakrise KW - Nachhaltigkeit KW - nachhaltiges Bauen KW - Urbanisierung KW - Bambus Y1 - 2023 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER - TY - THES A1 - Williams, Vivian T1 - Entwicklung eines neuen Erscheinungsbildes für Die Staatliche Antikensammlung in München N2 - Die Staatliche Antikensammlung in München ist eine antike Kunstsammlung, bestehend aus zwei Kunsthäusern. Das Haus der Glyptothek befindet sich auf der Nordseite und die Antikensammlung auf der Südseite des Königsplatzes. Während die Glyptothek Skulpturen ausstellt, zeigt die Antikensammlung Gebrauchsgegenstände und Objekte aus der etruskischen, griechischen und römischen Epoche. Sie gehört mit ihrer Kunstsammlung zu den weltweit führenden ihrer Art. In seinem Vorhaben, das Kulturerbe zu wahren, legt das Museum besonders hohen Wert auf Bildung und Vermittlung. Um dies langfristig zu gewährleisten, ist ein ausgeglichenes Erscheinungsbild zwischen Klassik und Modernität unentbehrlich. Die griechische Stilepoche zeichnet sich in ihrer abstrakten Nutzung von geometrischen Grundformen aus. Im Zusammenspiel von geometrischen Formen und Abstrahierungen entsteht ein neues Erscheinungsbild. KW - Klassizismus KW - Modernität KW - Abstrahierung KW - Kunstsammlung KW - Griechisch Y1 - 2023 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER - TY - THES A1 - Benavides, Lucie T1 - INKAS : User Experience und User Interface einer bestehenden CPQ-Webanwendung zur Erstellung von Konfiguratoren für variantenreiche Produkte. N2 - Im Rahmen dieser Masterarbeit wird die komplexe CPQ-Branchenlösung INKAS der it-motive AG konzeptionell und gestalterisch überarbeitet. Die mehrjährige Entwicklung von INKAS und etlicher separater Komponenten hat zu einer zum Teil inkonsistenten Oberfläche geführt, die Schwierigkeiten bei der Benutzung aufweist. Das neue User Interface, welches diese Masterarbeit entwickelt, soll durch einheitliche Interaktionsprinzipien zum einen die Usability und bestehende Funktionalitäten verbessern und zum anderen neue Funktionen leichter integrierbar machen. Diese Masterarbeit demonstriert somit ein Vorgehensmodell, durch welches komplexe existierende Branchenlösungen mithilfe eines nutzerzentrierten Redesigns eine nachhaltig verbesserte Produktqualität erreichen und die Integration neuer Technologien ermöglicht. In diesem Zusammenhang wird auch exemplarisch aufgezeigt, wie Designleistungen methodisch in bestehende agile Softwareentwicklungsprozesse integriert werden können. KW - CPQ KW - UI/UX-Design KW - Usability KW - Softwareentwicklung KW - Redesign Y1 - 2023 PB - FH Aachen CY - Aachen ER - TY - THES A1 - Hatke, Lars T1 - X Plore: human hybrid submarine N2 - Das „X Plore“ ist ein human hybrid angetriebenes Tauchboot, welches sowohl für den touristischen als auch privaten Gebrauch konzipiert ist. Das immersive Design des „X Plore" sorgt für ein eindrucksvolles Taucherlebnis. Das Konzept soll die Menschen über die aktuelle Not der Meere und ihrer Lebewesen aufklären und ihnen gleichzeitig die Möglichkeit geben, der Unterwasserwelt näher zukommen. Zudem soll es diese erhalten und ihre Bewohner:innen schützen. Des Weiteren thematisiert die Arbeit zukunftsorientierte Antriebs- und Batterietechniken und setzt sich mit der sinnvollen Integrierung dieser auseinander. KW - Entdecken KW - Abenteuer KW - Erkunden KW - Unterwasserwelt KW - Tauchboot Y1 - 2023 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER - TY - THES A1 - Rouenhoff, Saskia T1 - Blind – invisible connection : ein Spiel zur kritischen Auseinandersetzung mit den sozialen Medien. N2 - Im Computerspiel „blind – invisible connection“ taucht der Spieler in eine Fantasiewelt ein, die die sozialen Medien widerspiegelt und von einer Maschine beherrscht wird. Um zu erfahren, was in dieser Welt geschehen ist, muss die Geschichte Schritt für Schritt erspielt und wie ein Puzzle zusammengesetzt werden. Dabei interagieren die Spieler:innen mittels Dialogen mit den Bewohner:innen der Fantasiewelt und lösen Rätsel, die die Geschichte enthüllen. Durch Analogien zwischen der Fantasiewelt und den sozialen Medien wird die Funktionsweise und der Einfluss der Plattformen auf die Menschen und die Gesellschaft verdeutlicht. So wird eine Reflexion des eigenen Umgangs mit den sozialen Medien angeregt und Gesprächsstoff für Diskussionen unter den Spieler:innen und Mitmenschen geliefert. KW - Spiel KW - Computerspiel KW - App KW - Geschichte KW - Soziale Medien Y1 - 2022 PB - FH Aachen CY - Aachen ER - TY - THES A1 - Hetterle, Lukas T1 - Breathe N2 - Ein nachhaltiges, autonomes Fahrzeug, das in einer extrem schnellen und hektischen Welt, geprägt durch Digitalisierung und Urbanisierung, einen Moment der Ruhe bieten soll; eine Pause von der ständigen Flut von Eindrücken und Informationen. Ein immersives Design, das meditative und kreative Prozesse unterstützt und Mensch-Mensch sowie Mensch-Natur Begegnungen fördert. KW - Mobilität KW - Automobil KW - Design KW - Fahrzeug KW - Ruhe Y1 - 2023 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER - TY - JOUR A1 - Block, Franziska A1 - May, Alexander A1 - Wetzel, Katharina A1 - Adels, Klaudia A1 - Elbers, Gereon A1 - Schulze, Margit A1 - Monakhova, Yulia T1 - What is the best spectroscopic method for simultaneous analysis of organic acids and (poly)saccharides in biological matrices: Example of Aloe vera extracts? JF - Talanta Open N2 - Several species of (poly)saccharides and organic acids can be found often simultaneously in various biological matrices, e.g., fruits, plant materials, and biological fluids. The analysis of such matrices sometimes represents a challenging task. Using Aloe vera (A. vera) plant materials as an example, the performance of several spectro-scopic methods (80 MHz benchtop NMR, NIR, ATR-FTIR and UV–vis) for the simultaneous analysis of quality parameters of this plant material was compared. The determined parameters include (poly)saccharides such as aloverose, fructose and glucose as well as organic acids (malic, lactic, citric, isocitric, acetic, fumaric, benzoic and sorbic acids). 500 MHz NMR and high-performance liquid chromatography (HPLC) were used as the reference methods. UV–vis data can be used only for identification of added preservatives (benzoic and sorbic acids) and drying agent (maltodextrin) and semiquantitative analysis of malic acid. NIR and MIR spectroscopies combined with multivariate regression can deliver more informative overview of A. vera extracts being able to additionally quantify glucose, aloverose, citric, isocitric, malic, lactic acids and fructose. Low-field NMR measurements can be used for the quantification of aloverose, glucose, malic, lactic, acetic, and benzoic acids. The benchtop NMR method was successfully validated in terms of robustness, stability, precision, reproducibility and limit of detection (LOD) and quantification (LOQ), respectively. All spectroscopic techniques are useful for the screening of (poly)saccharides and organic acids in plant extracts and should be applied according to its availability as well as information and confidence required for the specific analytical goal. Benchtop NMR spectroscopy seems to be the most feasible solution for quality control of A. vera products. KW - Spectroscopy KW - (Poly)saccharides KW - Organic acids KW - Aloe vera KW - qNMR Y1 - 2023 U6 - https://doi.org/10.1016/j.talo.2023.100220 SN - 2666-8319 VL - 7 IS - Art. No. 100220 SP - 1 EP - 9 PB - Elsevier CY - Amsterdam ER - TY - JOUR A1 - Haeger, Gerrit A1 - Wirges, Jessika A1 - Tanzmann, Nicole A1 - Oyen, Sven A1 - Jolmes, Tristan A1 - Jaeger, Karl-Erich A1 - Schörken, Ulrich A1 - Bongaerts, Johannes A1 - Siegert, Petra T1 - Chaperone assisted recombinant expression of a mycobacterial aminoacylase in Vibrio natriegens and Escherichia coli capable of N-lauroyl-L-amino acid synthesis JF - Microbial Cell Factories N2 - Background Aminoacylases are highly promising enzymes for the green synthesis of acyl-amino acids, potentially replacing the environmentally harmful Schotten-Baumann reaction. Long-chain acyl-amino acids can serve as strong surfactants and emulsifiers, with application in cosmetic industries. Heterologous expression of these enzymes, however, is often hampered, limiting their use in industrial processes. Results We identified a novel mycobacterial aminoacylase gene from Mycolicibacterium smegmatis MKD 8, cloned and expressed it in Escherichia coli and Vibrio natriegens using the T7 overexpression system. The recombinant enzyme was prone to aggregate as inclusion bodies, and while V. natriegens Vmax™ could produce soluble aminoacylase upon induction with isopropyl β-d-1-thiogalactopyranoside (IPTG), E. coli BL21 (DE3) needed autoinduction with lactose to produce soluble recombinant protein. We successfully conducted a chaperone co-expression study in both organisms to further enhance aminoacylase production and found that overexpression of chaperones GroEL/S enhanced aminoacylase activity in the cell-free extract 1.8-fold in V. natriegens and E. coli. Eventually, E. coli ArcticExpress™ (DE3), which co-expresses cold-adapted chaperonins Cpn60/10 from Oleispira antarctica, cultivated at 12 °C, rendered the most suitable expression system for this aminoacylase and exhibited twice the aminoacylase activity in the cell-free extract compared to E. coli BL21 (DE3) with GroEL/S co-expression at 20 °C. The purified aminoacylase was characterized based on hydrolytic activities, being most stable and active at pH 7.0, with a maximum activity at 70 °C, and stability at 40 °C and pH 7.0 for 5 days. The aminoacylase strongly prefers short-chain acyl-amino acids with smaller, hydrophobic amino acid residues. Several long-chain amino acids were fairly accepted in hydrolysis as well, especially N-lauroyl-L-methionine. To initially evaluate the relevance of this aminoacylase for the synthesis of N-acyl-amino acids, we demonstrated that lauroyl-methionine can be synthesized from lauric acid and methionine in an aqueous system. Conclusion Our results suggest that the recombinant enzyme is well suited for synthesis reactions and will thus be further investigated. KW - Acyl-amino acids KW - Inclusion bodies KW - Chaperone co-expression KW - Vibrio natriegens KW - Aminoacylase Y1 - 2023 U6 - https://doi.org/10.1186/s12934-023-02079-1 SN - 1475-2859 N1 - Corresponding author: Petra Siegert IS - 22 SP - Article number: 77 (2023) PB - Springer Nature ER - TY - CHAP A1 - Engelmann, Ulrich M. A1 - Baumann, Martin ED - Herbig, Nicola ED - Poppelreuter, Stefan T1 - Moderationsexpertise für QMBs – die Methoden T2 - Qualitätsmanagement im Gesundheitswesen N2 - Damit Sie als Moderator effektiv und professionell moderieren können, sollten Sie die entsprechenden Methoden kennen. Mit den richtigen Methoden können Sie Diskussionen leiten, Konflikte lösen, die Teilnehmer motivieren und dafür sorgen, dass die Ziele der Veranstaltung erreicht werden. Außerdem helfen sie Ihnen, eine positive Atmosphäre zu schaffen und das Interesse der Teilnehmer zu halten. In diesem zweiten Beitrag der mehrteiligen Serie lernen Sie die grundsätzlichen Methoden kennen, um erfolgreiche Teamsitzungen, Arbeitsgruppentreffen, Kick-offs und Meetings durchzuführen. Y1 - 2023 SN - 978-3-8249-0714-4 SP - Kapitel 10815 PB - TÜV-Verlag CY - Köln ET - 60. Update ER - TY - JOUR A1 - Laarmann, Lukas A1 - Thoma, Andreas A1 - Misch, Philipp A1 - Röth, Thilo A1 - Braun, Carsten A1 - Watkins, Simon A1 - Fard, Mohammad T1 - Automotive safety approach for future eVTOL vehicles JF - CEAS Aeronautical Journal N2 - The eVTOL industry is a rapidly growing mass market expected to start in 2024. eVTOL compete, caused by their predicted missions, with ground-based transportation modes, including mainly passenger cars. Therefore, the automotive and classical aircraft design process is reviewed and compared to highlight advantages for eVTOL development. A special focus is on ergonomic comfort and safety. The need for further investigation of eVTOL’s crashworthiness is outlined by, first, specifying the relevance of passive safety via accident statistics and customer perception analysis; second, comparing the current state of regulation and certification; and third, discussing the advantages of integral safety and applying the automotive safety approach for eVTOL development. Integral safety links active and passive safety, while the automotive safety approach means implementing standardized mandatory full-vehicle crash tests for future eVTOL. Subsequently, possible crash impact conditions are analyzed, and three full-vehicle crash load cases are presented. KW - eVTOL development KW - eVTOL safety KW - Crashworthiness KW - Automotive safety approach KW - Full-vehicle crash test Y1 - 2023 U6 - https://doi.org/10.1007/s13272-023-00655-0 SN - 1869-5590 (Online) SN - 1869-5582 (Print) N1 - Corresponding author: Lukas Laarmann PB - Springer Nature ER - TY - CHAP A1 - Blanke, Tobias A1 - Schmidt, Katharina S. A1 - Göttsche, Joachim A1 - Döring, Bernd A1 - Frisch, Jérôme A1 - van Treeck, Christoph ED - Weidlich, Anke ED - Neumann, Dirk ED - Gust, Gunther ED - Staudt, Philipp ED - Schäfer, Mirko T1 - Time series aggregation for energy system design: review and extension of modelling seasonal storages T2 - Energy Informatics N2 - Using optimization to design a renewable energy system has become a computationally demanding task as the high temporal fluctuations of demand and supply arise within the considered time series. The aggregation of typical operation periods has become a popular method to reduce effort. These operation periods are modelled independently and cannot interact in most cases. Consequently, seasonal storage is not reproducible. This inability can lead to a significant error, especially for energy systems with a high share of fluctuating renewable energy. The previous paper, “Time series aggregation for energy system design: Modeling seasonal storage”, has developed a seasonal storage model to address this issue. Simultaneously, the paper “Optimal design of multi-energy systems with seasonal storage” has developed a different approach. This paper aims to review these models and extend the first model. The extension is a mathematical reformulation to decrease the number of variables and constraints. Furthermore, it aims to reduce the calculation time while achieving the same results. KW - Energy system KW - Renewable energy KW - Mixed integer linear programming (MILP) KW - Typical periods KW - Time-series aggregation Y1 - 2022 U6 - https://doi.org/10.1186/s42162-022-00208-5 SN - 2520-8942 N1 - 11th DACH+ Conference on Energy Informatics, 15-16 September 2022, Freiburg, Germany VL - 5 IS - 1, Article number: 17 PB - Springer Nature ER - TY - JOUR A1 - Peere, Wouter A1 - Blanke, Tobias ED - Vernon, Chris T1 - GHEtool: An open-source tool for borefield sizing in Python JF - Journal of Open Source Software N2 - GHEtool is a Python package that contains all the functionalities needed to deal with borefield design. It is developed for both researchers and practitioners. The core of this package is the automated sizing of borefield under different conditions. The sizing of a borefield is typically slow due to the high complexity of the mathematical background. Because this tool has a lot of precalculated data, GHEtool can size a borefield in the order of tenths of milliseconds. This sizing typically takes the order of minutes. Therefore, this tool is suited for being implemented in typical workflows where iterations are required. GHEtool also comes with a graphical user interface (GUI). This GUI is prebuilt as an exe-file because this provides access to all the functionalities without coding. A setup to install the GUI at the user-defined place is also implemented and available at: https://www.mech.kuleuven.be/en/tme/research/thermal_systems/tools/ghetool. KW - geothermal KW - energy KW - borefields KW - sizing Y1 - 2022 U6 - https://doi.org/10.21105/joss.04406 SN - 2475-9066 VL - 7 IS - 76 SP - 1 EP - 4, 4406 ER - TY - JOUR A1 - Pfaff, Raphael A1 - Babilon, Katharina T1 - Railway Challenge - moderne Auflage der Rainhill Trials? JF - Eisenbahntechnische Rundschau : ETR ; Impulsgeber für das System Bahn N2 - Die IMechE Railway Challenge wird jährlich in Stapleford, Großbritannien ausgetragen. Im Rahmen der Challenge entwickeln und bauen Studierende eine Lokomotive und vergleichen sich in verschiedenen Disziplinen, darunter eine automatisierte Zielbremsung, optimale Energierückgewinnung beim Bremsen und minimale Geräuschemissionen. Neben diesen und weiteren technischen Wettbewerbsdisziplinen treten die Fahrzeuge und die Teams auch in nicht-technischen Disziplinen wie einer Business Case Challenge an. Y1 - 2023 SN - 0013-2845 N1 - Homepageveröffentlichung unbefristet genehmigt für Fachhochschule Aachen / Rechte für einzelne Downloads und Ausdrucke für Besucher der Seiten genehmigt / © DVV Media Group GmbH VL - 2023 IS - 4 SP - 55 EP - 58 PB - DVV Media Group CY - Hamburg ER - TY - THES A1 - Weisbecker, Helen T1 - 550 nm : Farbwechsel von Tieren - Kommunikation in der Natur N2 - „550 nm“ befasst sich mit dem physiologischen Farbwechsel von Tieren. Einige Fische, Amphibien und Reptilien – wie beispielsweise das Chamäleon oder der Tintenfisch – können ihre Körperfarbe schnell wechseln. Unsere Natur leidet unter Kriegen und dem Klimawandel und verliert dadurch ihre Schönheit. Diese zeichnet sich vor allem durch die beachtliche Diversität der Körperfärbung von Tieren aus. Die Funktionen erstrecken sich über Tarnung, Auflauern oder Warnung bis hin zu einer Werbefärbung. Nicht nur Tiere nutzen Farbe als Ausdrucks- und Kommunikationsmittel. Auch Designer*innen bedienen sich an Farben, um Stimmungen zu vermitteln oder um Aufmerksamkeit und Individualität zu generieren. In „550 nm“ wird das Phänomen des Farbwechsels durch Illustrationen visualisiert und soll als Inspiration für Designinnovationen dienen. KW - Natur KW - Farbwechsel KW - Farbe KW - Tiere KW - Kommunikation Y1 - 2023 PB - FH Aachen CY - Aachen ER - TY - JOUR A1 - Funke, Harald A1 - Esch, Thomas A1 - Roosen, Petra T1 - Powertrain Adaptions for LPG Usage in General Aviation JF - MTZ worldwide N2 - In general aviation, too, it is desirable to be able to operate existing internal combustion engines with fuels that produce less CO₂ than Avgas 100LL being widely used today It can be assumed that, in comparison, the fuels CNG, LPG or LNG, which are gaseous under normal conditions, produce significantly lower emissions. Necessary propulsion system adaptations were investigated as part of a research project at Aachen University of Applied Sciences. Y1 - 2022 U6 - https://doi.org/10.1007/s38313-021-0756-6 VL - 2022 IS - 83 SP - 58 EP - 62 PB - Springer Nature CY - Basel ER - TY - JOUR A1 - Funke, Harald A1 - Esch, Thomas A1 - Roosen, Petra T1 - Antriebssystemanpassungen zur Verwendung von LPG als Flugkraftstoff JF - Motortechnische Zeitschrift (MTZ) N2 - Auch in der allgemeinen Luftfahrt wäre es wünschenswert, die bereits vorhandenen Verbrennungsmotoren mit weniger CO₂-trächtigen Kraftstoffen als dem heute weit verbreiteten Avgas 100LL betreiben zu können. Es ist anzunehmen, dass im Vergleich die unter Normalbedingungen gasförmigen Kraftstoffe CNG, LPG oder LNG deutlich weniger Emissionen produzieren. Erforderliche Antriebssystemanpassungen wurden im Rahmen eines Forschungsprojekts an der FH Aachen untersucht. Y1 - 2022 U6 - https://doi.org/10.1007/s35146-021-0778-2 VL - 2022 IS - 83 SP - 58 EP - 62 PB - Springer Nature CY - Basel ER - TY - THES A1 - Westhoff, Katharina T1 - Fensterleben : eine Sammlung über das Treffen von privatem und öffentlichem Leben N2 - Im Projekt „Fensterleben” werden Alltagsgeschichten, die sich vor und in einer Erdgeschosswohnung abspielen, graphisch als Videos aufbereitet. In einer mehrteiligen Serie werden die Eindrücke und Perspektiven auf „Bürgersteig-Geschehnisse” und was hinter den Fenstern passiert, veranschaulicht. Besonderes Interesse gilt dem Zusammenspiel von privatem und öffentlichem Raum: was wurde zwischen Fensterbank und Bürgersteig ausgetauscht und weitergegeben. KW - Kurzfilme KW - Fenster KW - Serie KW - Pizza KW - Telefonat Y1 - 2023 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER - TY - THES A1 - Heising, Michelle T1 - Nachhaltige Gestaltung im urbanen öffentlichen Raum : erneuerbare Energien in Begegnungsräume integrieren N2 - RƎURB (Reurbanization & Renewable Energy) ist ein Konzept zur Integration von erneuerbaren Energien in einen urbanen Begegnungsraum. Es beinhaltet das Design eines skulpturalen Kleinwindkraftwerks und eines Solar-Pavillons mit einer Sitzlandschaft für einen energieautarken, öffentlichen Platz. Durch die Integration eines W-LAN Hotspots und Lademöglichkeiten in der Sitzlandschaft bringt RƎURB nicht nur grünen Strom in die Stadt, sondern gewährleistet der Bevölkerung auch Zugang zur Digitalisierung und einen kostenlosen Arbeitsraum. Windturbine: Herkömmliche Windräder können in der Stadt nicht genutzt werden. Die RƎURB-Windsäule ist darauf spezialisiert, die urbanen Winde aus allen Richtungen aufzunehmen und funktioniert schon bei einem leichten Windstoß. Durch das elegante Design lassen sich die Technologien als ästhetischen Blickfang in das moderne Stadtbild integrieren. KW - Erneuerbare Energien KW - Urbane Gestaltung KW - Solarenergie KW - Windkraft KW - Architektur Y1 - 2023 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER - TY - THES A1 - Kilcher, Mathias T1 - Barrierefreies Klettern : ein System zur Inklusion sehbehinderter Menschen in den Klettersport N2 - Ziel des Projekts war die Entwicklung eines Systems, das es Menschen mit starker Sehbehinderung ermöglicht, Klettersport als ein Training für ihren Körper und ihren Orientierungssinn nutzen zu können. Inklusion ist als gesellschaftliches Thema in den letzten Jahren stark in den Fokus gerückt. Dennoch ist es für Menschen mit Behinderung oft schwer, sozialen Anschluss zu finden. Dies wird zusätzlich durch das mangelnde Angebot an inklusiven Freizeitaktivitäten erschwert. Apollon ermöglicht Menschen mit starker Sehbehinderung die Orientierung während des Kletterns, indem es einerseits Informationen vermittelt, die normalerweise nur visuell wahrgenommen werden können und andererseits dabei hilft, sich besser an bereits gekletterte Routen zu erinnern. Das System setzt sich aus 3 Komponenten zusammen. Die Tritthilfen helfen der blinden Person dabei, auch kleine Tritte zu finden. Die taktilen Wegmarken stellen eine Art Checkpoint dar und helfen der blinden Person dabei, die Route in mehrere Abschnitte zu unterteilen. Gleichzeitig weisen sie darauf hin, welches Feature die kletternde Person erwartet. Die taktile Karte ist modular aufgebaut und setzt sich aus einer Legende und den Repräsentanten der Wegmarken einer Route zusammen. Analog zu dem Betrachten der Route ist die blinde Person so vor dem Klettern in der Lage, Informationen über die Route zu erfahren. KW - Inklusion KW - Klettern KW - Sport Y1 - 2023 PB - FH Aachen CY - Aachen ER - TY - THES A1 - Kuck, Fabian T1 - Commuter Zone : Rückzugsort für Pendelnde zum Ausgleich ihrer Reisezeit N2 - Die „Commuter Zone“ setzt sich mit dem Zeitverlust Pendelnder auseinander. Berufliche Ziele treiben immer mehr Menschen an, längere Strecken zurückzulegen. Dabei büßen sie den Zeitaufwand an privater Stelle ein. Als Rückzugsort für Alleinreisende schafft die „Commuter Zone“ ein effektiv nutzbares Zeitfenster. Dazu wird die Rücksichtnahme der Routinierten zueinander genutzt und gefördert. Sitz- und Arbeitsflächen lassen sich zurückklappen und erleichtern das Aussteigen. Der begrenzte Raum wird intensiv genutzt. So entsteht Komfort durch die Zuversicht, einen Sitzplatz zu erhalten. Und dank der Zusammensetzung der Sitzkonstellation bleibt das Arbeitsgeschehen privat. Letztlich bietet die „Commuter Zone“ den zunehmend selbstbestimmenden Beschäftigten neue Möglichkeiten zur Arbeitseinteilung und schafft Qualitätszeit im Privaten. KW - Pendelnde KW - Bahnfahrt KW - Work-Life-Balance KW - Workaholic KW - Bahn Y1 - 2023 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER - TY - THES A1 - Tran, Hui Ming T1 - Das Haus des Meeres : Entwicklung und Konzeption eines neuen Erscheinungsbildes für den Aqua Terra Zoo N2 - Im Zentrum von Wien befindet sich in einem ehemaligen Flakturm aus dem 2. Weltkrieg, das Haus des Meeres. Auf ca 5000m2 beherbergen sie ca. 10.000 Tiere. Der Fokus liegt dabei auf die Unterwasserwelt und bietet einen ausgiebigen Einblick in die Welt der Meere. Das neue Erscheinungsbild positioniert die private und gemeinnützige Einrichtung sowohl als Ort des Zusammenkommens als auch der Wissensvermittlung. Dabei soll das Designkonzept vor dem Betreten des Zoos seine besondere Baukonstruktion aufzeigen und von Anfang an die Tiefe sowie Tiefenzonen der Meere einbeziehen. Damit distanzieren sie sich entscheidend von ähnlichen Institutionen. Inspiriert von der Teilung zwischen der Oberfläche und dem Meer, entstand eine feine abstrakte Skala. Diese visualisiert den Meeresspiegel mit seiner Tiefe und dient medienübergreifend als Orientierungshilfe. KW - Corporate Design KW - Ozean KW - Zoo KW - Meere KW - Erscheinungsbild Y1 - 2023 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER - TY - THES A1 - Trautmann, Christina T1 - Dirty Air N2 - Die Formel 1 ist ein Extremsport und soll wie viele andere Wettbewerbe in diesem Bereich unterhalten. Die Konkurrenz unter den Fahrern ist jederzeit präsent, jedoch das dadurch steigende Gefahrenpotenzial nicht. In der Graphic Novel „Dirty Air“ wir auf Basis eines dokumentarisch-informativen Ansatzes aufgezeigt, inwiefern die Rivalität zweier Fahrer Auswirkungen auf die Sicherheit des Sports haben kann. Es wird über die wichtigsten Ereignisse der Saison 2021 erzählt, die beispielhaft dafür stehen, wie sich der Wettbewerb zuspitzen kann. Die Geschehnisse sind realen Gegebenheiten nachempfunden und illustrativ umgesetzt. Ziel der Arbeit ist es, die Leser*innen zum Nachdenken anzuregen und Verständnis zu schaffen. Rivalitäten sind wichtig und notwendig im Sport, sollten jedoch kein Anker für Hass und unüberlegte Risiken sein, egal ob innerhalb des Fahrerlagers oder der Fangemeinschaft. KW - Illustration KW - Formel 1 KW - Konkurrenz KW - Graphic Novel KW - Rivalität Y1 - 2023 PB - FH Aachen CY - Aachen ER - TY - THES A1 - Hotze, Larissa T1 - Ein Abschied auf Zeit : der Totenritus der Toraja N2 - Die Kultur der Tana Toraja haben einen ganz besonderen Umgang mit dem Tod. Verstorbene werden bis zu der eigentlichen Bestattung als „krank“ angesehen und solange im Alltag mit eingebunden, ganz so als ob es sich um eine noch lebende Person handelt. Der Totenritus kann mehrere Tage andauern und Familie und Freund reisen aus dem ganzen Land herbei, um dem Fest beizuwohnen. Hier geht niemand einsam und das Sterben ist sogar ein wichtiger Bestandteil des Lebens. Studien aus Deutschland hingegen zeigen, dass zunehmend einsamer gestorben wird. Außerdem ist der Tod weiterhin ein Tabuthema. Genau dort setzt die Ausstellung und die entstandene Publikation über die Toraja-Kultur an. Einblicke in den Umgang mit dem Tod anderer Länder regen zu Reflexion und Diskurs an. Gestalterisch gibt es immer wieder Kontaktpunkte, die das Zusammenspiel der Lebenden und dem Jenseits widerspiegeln. KW - Ausstellungsdesign KW - Editorial KW - Publikation KW - Sonderausstellung KW - Ausstellungskonzept Y1 - 2023 PB - FH Aachen CY - Aachen ER - TY - THES A1 - Kappel, Jana Naomi T1 - KLIKK : ein smartes Kinderprodukt für den altersgerechten Einstieg in die digitale Welt N2 - Die neue Generation wird mit einer Medienwelt konfrontiert, welche nicht auf unsere kleinen Nutzer:innen ausgelegt ist. Die Verwendung von digitalen Medien hatte nie einen größeren Einfluss auf unsere Gesellschaft wie im Hier und Jetzt. Somit ist es von großer Relevanz, diese Nutzung kindergerechter zu gestalten und einen sicheren Rahmen für sie zu schaffen. Das Bachelorprojekt „KLIKK“ legt einen Lösungsentwurf für den altersgerechten Einstieg für Kinder in diese digitale Welt vor, um den richtigen Umgang mit Smartwatches und darauf aufbauende Medien zu ermöglichen und gleichzeitig einen pädagogischen Mehrwert zu bieten. Das didaktische Produktkonzept, welches explizit für Kinder designed wurde, beinhaltet das Erlernen des Uhrlesens und befriedigt das aufkommende Bedürfnis nach Vernetzung in einem sicheren System. Zudem fördert es die Autonomie und ist an die kindliche Motorik angepasst. Mitinitiator und Namensgeber für diese Konzeption ist die deutsche Kinderuhrenmarke KWIO. KLIKK inkludiert Sicherheit, die Freude am Lernen und bietet eine Möglichkeit, die Kleinen ganz groß in unsere digitale Welt aufzunehmen. KW - Smartwatch KW - conceptual design KW - industrial design KW - children Y1 - 2023 PB - FH Aachen CY - Aachen ER - TY - THES A1 - Katemann, Ronja Mairin T1 - Gaming for everyone : gender-inklusives Gaming Equipment N2 - Das Ausleben von Sexualität und Gender befindet sich im gesellschaftlichen Wandel. Vor allem junge Menschen lassen ihre Lebenswege nicht mehr von traditionellen Geschlechterrollen und -normen leiten. In einigen Bereichen ist das schon deutlich sichtbar, während andere Bereiche noch vor Herausforderungen stehen, wenn es um Inklusion, Akzeptanz und Repräsentation geht. Besonders betroffen ist dabei der Gamingbereich, der repräsentativ nach wie vor ein männlich-dominiertes Gebiet zu sein scheint und durch Vorurteile gegenüber Frauen und der LGBTQIA+ Community stigmatisiert ist. Die _FLUX Gaming Maus soll durch Gender-inklusives Design dazu beitragen, stereotype Rollenbilder in der Gaming Welt aufzubrechen und die Community nachhaltig wachsen zu lassen. Sie bietet dabei eine Alternative zu den „typisch männlich“ wirkenden Gaming Produkten auf dem Markt. Durch verschiedene Individualisierungsmöglichkeiten in Funktion und Gestalt kann _FLUX in einem Online-Konfigurator an den persönlichen Spielstil angepasst werden. So vermittelt _FLUX Zugehörigkeit und Repräsentation unabhängig von Geschlecht und bietet Spaß am Gaming für jede:n. KW - Produkt Design KW - Spiele KW - gendern KW - Gaming Produkte KW - Gaming Maus Y1 - 2023 PB - FH Aachen CY - Aachen ER - TY - CHAP A1 - Elsen, Ingo A1 - Kraiss, Karl-Friedrich A1 - Krumbiegel, Dirk T1 - Pixel based 3D object recognition with bidirectional associative memories T2 - International Conference on Neural Networks 1997 N2 - This paper addresses the pixel based recognition of 3D objects with bidirectional associative memories. Computational power and memory requirements for this approach are identified and compared to the performance of current computer architectures by benchmarking different processors. It is shown, that the performance of special purpose hardware, like neurocomputers, is between one and two orders of magnitude higher than the performance of mainstream hardware. On the other hand, the calculation of small neural networks is performed more efficiently on mainstream processors. Based on these results a novel concept is developed, which is tailored for the efficient calculation of bidirectional associative memories. The computational efficiency is further enhanced by the application of algorithms and storage techniques which are matched to characteristics of the application at hand. Y1 - 1997 SN - 0-7803-4122-8 N1 - June 9 - 12, 1997, Westin Galleria Hotel Houston, Texas, USA. SP - 1679 EP - 1684 PB - IEEE CY - New York ER - TY - CHAP A1 - Elsen, Ingo T1 - A pixel based approach to view based object recognition with self-organizing neural networks T2 - IECON'98. Proceedings of the 24th Annual Conference of the IEEE Industrial Electronics Society N2 - This paper addresses the pixel based classification of three dimensional objects from arbitrary views. To perform this task a coding strategy, inspired by the biological model of human vision, for pixel data is described. The coding strategy ensures that the input data is invariant against shift, scale and rotation of the object in the input domain. The image data is used as input to a class of self organizing neural networks, the Kohonen-maps or self-organizing feature maps (SOFM). To verify this approach two test sets have been generated: the first set, consisting of artificially generated images, is used to examine the classification properties of the SOFMs; the second test set examines the clustering capabilities of the SOFM when real world image data is applied to the network after it has been preprocessed to be invariant against shift, scale and rotation. It is shown that the clustering capability of the SOFM is strongly dependant on the invariance coding of the images. Y1 - 1998 SN - 0-7803-4503-7 U6 - https://doi.org/10.1109/IECON.1998.724032 N1 - Aachen, 31 August 1998 - 04 September 1998 SP - 2040 EP - 2044 PB - IEEE CY - New York ER - TY - JOUR A1 - Elsen, Ingo A1 - Kraiss, Karl-Friedrich A1 - Krumbiegel, Dirk A1 - Walter, Peter A1 - Wickel, Jochen T1 - Visual information retrieval for 3D product identification: a midterm report JF - KI - Künstliche Intelligenz Y1 - 1999 SN - 1610-1987 SN - 0933-1875 VL - 13 IS - 1 SP - 64 EP - 67 PB - Springer CY - Berlin ER - TY - JOUR A1 - Maurer, Florian A1 - Rieke, Christian A1 - Schemm, Ralf A1 - Stollenwerk, Dominik T1 - Analysis of an urban grid with high photovoltaic and e-mobility penetration JF - Energies N2 - This study analyses the expected utilization of an urban distribution grid under high penetration of photovoltaic and e-mobility with charging infrastructure on a residential level. The grid utilization and the corresponding power flow are evaluated, while varying the control strategies and photovoltaic installed capacity in different scenarios. Four scenarios are used to analyze the impact of e-mobility. The individual mobility demand is modelled based on the largest German studies on mobility “Mobilität in Deutschland”, which is carried out every 5 years. To estimate the ramp-up of photovoltaic generation, a potential analysis of the roof surfaces in the supply area is carried out via an evaluation of an open solar potential study. The photovoltaic feed-in time series is derived individually for each installed system in a resolution of 15 min. The residential consumption is estimated using historical smart meter data, which are collected in London between 2012 and 2014. For a realistic charging demand, each residential household decides daily on the state of charge if their vehicle requires to be charged. The resulting charging time series depends on the underlying behavior scenario. Market prices and mobility demand are therefore used as scenario input parameters for a utility function based on the current state of charge to model individual behavior. The aggregated electricity demand is the starting point of the power flow calculation. The evaluation is carried out for an urban region with approximately 3100 residents. The analysis shows that increased penetration of photovoltaics combined with a flexible and adaptive charging strategy can maximize PV usage and reduce the need for congestion-related intervention by the grid operator by reducing the amount of kWh charged from the grid by 30% which reduces the average price of a charged kWh by 35% to 14 ct/kWh from 21.8 ct/kWh without PV optimization. The resulting grid congestions are managed by implementing an intelligent price or control signal. The analysis took place using data from a real German grid with 10 subgrids. The entire software can be adapted for the analysis of different distribution grids and is publicly available as an open-source software library on GitHub. KW - distribution grid simulation KW - smart-charging KW - e-mobility Y1 - 2023 U6 - https://doi.org/10.3390/en16083380 SN - 1996-1073 N1 - This article belongs to the Special Issue "Advanced Solutions for the Efficient Integration of Electric Vehicles in Electricity Grids" N1 - Corresponding author: Florian Maurer VL - 16 IS - 8 PB - MDPI CY - Basel ER - TY - JOUR A1 - Elsen, Ingo A1 - Kraiss, Karl-Friedrich T1 - System concept and realization of a scalable neurocomputing architecture JF - Systems Analysis Modelling Simulation N2 - This paper describes the realization of a novel neurocomputer which is based on the concepts of a coprocessor. In contrast to existing neurocomputers the main interest was the realization of a scalable, flexible system, which is capable of computing neural networks of arbitrary topology and scale, with full independence of special hardware from the software's point of view. On the other hand, computational power should be added, whenever needed and flexibly adapted to the requirements of the application. Hardware independence is achieved by a run time system which is capable of using all available computing power, including multiple host CPUs and an arbitrary number of neural coprocessors autonomously. The realization of arbitrary neural topologies is provided through the implementation of the elementary operations which can be found in most neural topologies. Y1 - 1999 SN - 0232-9298 SN - 1029-4902 VL - 35 IS - 4 SP - 399 EP - 419 PB - Gordon and Breach Science Publishers CY - Amsterdam ER - TY - CHAP A1 - Walter, Peter A1 - Elsen, Ingo A1 - Müller, Holger A1 - Kraiss, Karl-Friedrich T1 - 3D object recognition with a specialized mixtures of experts architecture T2 - IJCNN'99. International Joint Conference on Neural Networks. Proceedings N2 - Aim of the AXON2 project (Adaptive Expert System for Object Recogniton using Neuml Networks) is the development of an object recognition system (ORS) capable of recognizing isolated 3d objects from arbitrary views. Commonly, classification is based on a single feature extracted from the original image. Here we present an architecture adapted from the Mixtures of Eaqerts algorithm which uses multiple neuml networks to integmte different features. During tmining each neural network specializes in a subset of objects or object views appropriate to the properties of the corresponding feature space. In recognition mode the system dynamically chooses the most relevant features and combines them with maximum eficiency. The remaining less relevant features arz not computed and do therefore not decelerate the-recognition process. Thus, the algorithm is well suited for ml-time applications. Y1 - 1999 SN - 0-7803-5529-6 U6 - https://doi.org/10.1109/IJCNN.1999.836243 SN - 1098-7576 N1 - Washington, DC 10-16.07.1999 SP - 3563 EP - 3568 PB - IEEE CY - New York ER - TY - JOUR A1 - Fayyazi, Mojgan A1 - Sardar, Paramjotsingh A1 - Thomas, Sumit Infent A1 - Daghigh, Roonak A1 - Jamali, Ali A1 - Esch, Thomas A1 - Kemper, Hans A1 - Langari, Reza A1 - Khayyam, Hamid T1 - Artificial intelligence/machine learning in energy management systems, control, and optimization of hydrogen fuel cell vehicles N2 - Environmental emissions, global warming, and energy-related concerns have accelerated the advancements in conventional vehicles that primarily use internal combustion engines. Among the existing technologies, hydrogen fuel cell electric vehicles and fuel cell hybrid electric vehicles may have minimal contributions to greenhouse gas emissions and thus are the prime choices for environmental concerns. However, energy management in fuel cell electric vehicles and fuel cell hybrid electric vehicles is a major challenge. Appropriate control strategies should be used for effective energy management in these vehicles. On the other hand, there has been significant progress in artificial intelligence, machine learning, and designing data-driven intelligent controllers. These techniques have found much attention within the community, and state-of-the-art energy management technologies have been developed based on them. This manuscript reviews the application of machine learning and intelligent controllers for prediction, control, energy management, and vehicle to everything (V2X) in hydrogen fuel cell vehicles. The effectiveness of data-driven control and optimization systems are investigated to evolve, classify, and compare, and future trends and directions for sustainability are discussed. KW - optimization system KW - intelligent control KW - fuel cell vehicle KW - machine learning KW - artificial intelligence KW - intelligent energy management Y1 - 2023 U6 - https://doi.org/10.3390/su15065249 N1 - This article belongs to the Special Issue "Circular Economy and Artificial Intelligence" VL - 15 IS - 6 SP - 38 PB - MDPI CY - Basel ER - TY - THES A1 - Elsen, Ingo T1 - Ansichtenbasierte 3D-Objekterkennung mit erweiterten selbstorganisierenden Merkmalskarten KW - Dreidimensionale Bildverarbeitung KW - Objekterkennung KW - CCD-Bildwandler KW - Vorverarbeitung KW - Klassifikator Y1 - 2000 SN - 978-3-18-363110-0 SN - 3-18-363110-5 SN - 0341-1796 SN - 0178-9627 N1 - Fortschritt-Berichte VDI : Reihe 10, Informatik, Kommunikation 631 PB - VDI-Verlag CY - Düsseldorf ER - TY - JOUR A1 - Elsen, Ingo A1 - Hartung, Frank A1 - Horn, Uwe A1 - Kampmann, Markus A1 - Peters, Liliane ED - Voas, Jeffrey T1 - Streaming technology in 3G mobile communication systems JF - Computer : innovative technology for computer professionals N2 - Third-generation mobile communication systems will combine standardized streaming with a range of unique services to provide high-quality Internet content that meets the specific needs of the rapidly growing mobile market. Y1 - 2001 SN - 0018-9162 SN - 1558-0814 VL - 34 IS - 9 Seiten SP - 46 EP - 52 PB - IEEE CY - New York ER - TY - CHAP A1 - Elsen, Ingo A1 - Hawari, Asma A1 - Johnen, Uwe ED - Pietsch, Wolfram ED - Krams, Benedikt T1 - Produktkernel in der Systemintegration (Erfahrungsbericht aus der Praxis) T2 - Vom Projekt zum Produkt - Fachtagung des GI-Fachausschusses Management der Anwendungsentwicklung und -wartung im Fachbereich Wirtschaftsinformatik (WI-MAW), 1. - 3. Dezember 2010 in Aachen N2 - In der Vergangenheit basierten große Systemintegrationsprojekte in der Regel auf Individualentwicklungen für einzelne Kunden. Getrieben durch Kostendruck steigt aber der Bedarf nach standardisierten Lösungen, die gleichzeitig die individuellen Anforderungen des jeweiligen Umfelds berücksichtigen. T-Systems GEI GmbH wird beiden Anforderungen mit Produktkerneln gerecht. Neben den technischen Aspekten der Kernelentwicklung spielen besonders organisatorische Aspekte eine Rolle, um Kernel effizient und qualitativ hochwertig zu entwickeln, ohne deren Funktionalitäten ins Uferlose wachsen zu lassen. Umgesetzt hat T-Systems dieses Konzept für Flughafeninformationssysteme. Damit kann dem wachsenden Bedarf der Flughafenbetreiber nach einer effizienten und kostengünstigen Softwarelösung zur Unterstützung Ihrer Geschäftsprozesse entsprochen werden. Y1 - 2010 SN - 9783885792727 SN - 1617-5468 SP - 93 EP - 102 PB - Gesellschaft für Informatik eV CY - Bonn ER - TY - CHAP A1 - Elsen, Ingo A1 - Schmalzbauer, Michael ED - Reussner, Ralf ED - Grund, Matthias ED - Andreas, Oberweis ED - Tichy, Walter T1 - Messsystematik zur Steuerung der Produkt- und Prozessqualität in Systemintegrationsprojekten – ein Erfahrungsbericht T2 - Software Engineering 2011 - Fachtagung des GI-Fachbereichs Softwaretechnik, 21. - 25. Februar 2011 in Karlsruhe N2 - Der Erfolg eines Softwarenentwicklungsprojektes insbesondere eines Systemintegrationsprojektes wird mit der Erfüllung des „Teufelsdreiecks“, „In-Time“, „In-Budget“, „In-Quality“ gemessen. Hierzu ist die Kenntnis der Software- und Prozessqualität essenziell, um die Einhaltung der Qualitätskriterien festzustellen, aber auch, um eine Vorhersage hinsichtlich Termin- und Budgettreue zu treffen. Zu diesem Zweck wurde in der T-Systems Systems Integration ein System aus verschiedenen Key Performance Indikatoren entworfen und in der Organisation implementiert, das genau das leistet und die Kriterien für CMMI Level 3 erfüllt. Y1 - 2011 SN - 9783885792772 SN - 1617-5468 PB - Gesellschaft für Informatik eV CY - Bonn ER - TY - CHAP A1 - Dey, Thomas A1 - Elsen, Ingo A1 - Ferrein, Alexander A1 - Frauenrath, Tobias A1 - Reke, Michael A1 - Schiffer, Stefan ED - Makedon, Fillia T1 - CO2 Meter: a do-it-yourself carbon dioxide measuring device for the classroom T2 - PETRA '21: Proceedings of the 14th Pervasive Technologies Related to Assistive Environments Conference N2 - In this paper we report on CO2 Meter, a do-it-yourself carbon dioxide measuring device for the classroom. Part of the current measures for dealing with the SARS-CoV-2 pandemic is proper ventilation in indoor settings. This is especially important in schools with students coming back to the classroom even with high incidents rates. Static ventilation patterns do not consider the individual situation for a particular class. Influencing factors like the type of activity, the physical structure or the room occupancy are not incorporated. Also, existing devices are rather expensive and often provide only limited information and only locally without any networking. This leaves the potential of analysing the situation across different settings untapped. Carbon dioxide level can be used as an indicator of air quality, in general, and of aerosol load in particular. Since, according to the latest findings, SARS-CoV-2 can be transmitted primarily in the form of aerosols, carbon dioxide may be used as a proxy for the risk of a virus infection. Hence, schools could improve the indoor air quality and potentially reduce the infection risk if they actually had measuring devices available in the classroom. Our device supports schools in ventilation and it allows for collecting data over the Internet to enable a detailed data analysis and model generation. First deployments in schools at different levels were received very positively. A pilot installation with a larger data collection and analysis is underway. KW - embedded hardware KW - sensor networks KW - information systems KW - education KW - do-it-yourself Y1 - 2021 SN - 9781450387927 U6 - https://doi.org/10.1145/3453892.3462697 N1 - PETRA '21: The 14th PErvasive Technologies Related to Assistive Environments Conference Corfu Greece 29 June 2021- 2 July 2021 SP - 292 EP - 299 PB - Association for Computing Machinery CY - New York ER - TY - CHAP A1 - Maurer, Florian T1 - Framework to provide a simulative comparison of different energy market designs T2 - Energy Informatics N2 - Useful market simulations are key to the evaluation of diferent market designs existing of multiple market mechanisms or rules. Yet a simulation framework which has a comparison of diferent market mechanisms in mind was not found. The need to create an objective view on different sets of market rules while investigating meaningful agent strategies concludes that such a simulation framework is needed to advance the research on this subject. An overview of diferent existing market simulation models is given which also shows the research gap and the missing capabilities of those systems. Finally, a methodology is outlined how a novel market simulation which can answer the research questions can be developed. Y1 - 2022 U6 - https://doi.org/10.1186/s42162-022-00215-6 SN - 2520-8942 N1 - 11th DACH+ Conference on Energy Informatics, 15-16 September 2022, Freiburg, Germany VL - 5 IS - 2, Article number: 12 SP - 18 EP - 20 PB - Springer Nature ER - TY - CHAP A1 - Altherr, Lena A1 - Conzen, Max A1 - Elsen, Ingo A1 - Frauenrath, Tobias A1 - Lyrmann, Andreas ED - Reiff-Stephan, Jörg ED - Jäkel, Jens ED - Schwarz, André T1 - Sensor retrofitting of existing buildings in an interdisciplinary teaching project at university level T2 - Tagungsband AALE 2023 : mit Automatisierung gegen den Klimawandel N2 - Existing residential buildings have an average lifetime of 100 years. Many of these buildings will exist for at least another 50 years. To increase the efficiency of these buildings while keeping costs at reasonable rates, they can be retrofitted with sensors that deliver information to central control units for heating, ventilation and electricity. This retrofitting process should happen with minimal intervention into existing infrastructure and requires new approaches for sensor design and data transmission. At FH Aachen University of Applied Sciences, students of different disciplines work together to learn how to design, build, deploy and operate such sensors. The presented teaching project already created a low power design for a combined CO2, temperature and humidity measurement device that can be easily integrated into most home automation systems KW - Building Automation KW - Smart Building KW - CO2 KW - Carbon Dioxide KW - Education Y1 - 2023 SN - 978-3-910103-01-6 U6 - https://doi.org/10.33968/2023.04 N1 - 19. AALE-Konferenz. Luxemburg, 08.03.-10.03.2023. BTS Connected Buildings & Cities Luxemburg (Tagungsband unter https://doi.org/10.33968/2023.01) SP - 31 EP - 40 PB - le-tex publishing services GmbH CY - Leipzig ER - TY - THES A1 - Balthazar, Kim T1 - SWASH : endlich bequem waschen N2 - Der S W A S H ist eine innovative Produktlösung zur Reduzierung von Pain Points beim alltäglichen Reinigen von Textilien. Schmutzige Kleidungsstücke müssen in Zukunft weniger mit Wasser und Waschmitteln in Berührung kommen. Dadurch minimiert sich der Ressourcenverbrauch, die Langlebigkeit der Kleidung wird erhöht und die umfangreiche Aufgabe des Waschens wird bequemer, ohne Einbußen in Sauberkeit und Hygiene haben zu müssen. Der S W A S H wird durch KI gesteuert und gewährleistet so eine kinderleichte Nutzbarkeit. Da er mit Wassertanks betrieben wird, benötigt man keinen Wasseranschluss und kann die Platzierung frei wählen. Durch den modularen und minimalistischen Aufbau kann er auf die Ästhetik des individuellen Wohnraums angepasst werden. Der Refresher mit Waschfunktion kann als freistehendes Möbelstück erworben oder in einen vorhandenen Kleiderschrank integriert werden. KW - Waschmaschine KW - nachhaltig KW - Produktdesign KW - Skandinavien KW - modular Y1 - 2023 PB - FH Aachen CY - Aachen ER - TY - THES A1 - Brunsbach, Katharina T1 - Lesesessel im dänischen Stil N2 - Bei dem Möbel wurde Wert auf Nachhaltigkeit, Langlebigkeit und zeitloses Design gelegt. Ziel war es, ein Möbel zu entwerfen, welches bequem, minimalistisch und alltagstauglich ist. Der Sessel mit passendem Hocker besteht aus einem Holzgestell mit aufliegenden Polstern. Die Gestelle sind aus Rüsterholz mit handwerklichen Verbindungen gefertigt. Die Polster bestehen aus 10 cm dickem Schaumstoff, bezogen mit einem Chenille Möbelstoff. Durch lösbare Verbindungen und Sitzlatten, die in Austaschungen gesteckt werden, lassen sich die Möbel vom Endkunden leicht selbst aufbauen und ermöglichen einen flachen Versandkarton. Der Sessel lädt zum Entspannen und Lesen ein. Er ist bequem und gewährleistet dadurch ein stundenlanges Nutzen. „HVILE“ ein Ort der Ruhe und Eintritt in eine andere Welt. KW - Lesesessel KW - Dänisch KW - Holzverbindungen KW - Polster KW - Rüster Y1 - 2023 PB - FH Aachen CY - Aachen ER - TY - THES A1 - Donker, Carla T1 - ADIE : Keramische Fassaden- und Wandverkleidung - Funktion und Wirkung von Schönheit im Design N2 - „ADIE“ ist eine Produktfamilie von Keramikplatten und Fliesen mit dreidimensionaler Oberfläche, welche durch Form und Farbe Schönheit zum Ausdruck bringen. Sie sind sowohl im Kontext der Architektur als Fassadenverkleidung anwendbar als auch im Innenbereich als Wandverkleidung. Die Fähigkeit von Schönheit, unsere Umgebung zu transformieren, nimmt eine leitende Rolle in dieser Arbeit ein. Als Inspirationsquelle für die Entwürfe dienten Dinge, die dem allgemeinen Schönheitsempfinden entsprechen: Wasser, Blüten, der Himmel und andere Naturphänomene. Diese wurden abstrahiert, in Reliefs übersetzt und in drei unterschiedliche Module weiterentwickelt. Sie sind konzeptionell frei skalierbar und wurden in Kleinserie im Gussverfahren prototypisiert. Mit „ADIE“ sollte auf die Funktion von Schönheit im Design Bezug genommen werden und etwas entstehen, das einfach „nur“ schön ist. KW - Fliesen KW - Keramik KW - Fassadenverkleidung KW - Wandverkleidung KW - Schönheit Y1 - 2023 PB - FH Aachen CY - Aachen ER - TY - THES A1 - Elsen, Charles T1 - VEKSLE N2 - Die beste Form der Nachhaltigkeit ist jahrzehntelange Freude. VEKSLE beschreibt eine Möbelkollektion, die sich in Zeiten des Überangebots und des ständigen Wohnraumwechsels anpasst. Die minimalistische Ästhetik mit hohem Sitzkomfort orientiert sich dabei an den Bedürfnissen von Verbraucher:innen und lässt sich im Laufe seiner Nutzungsperiode stetig an neue Einrichtungsstyles und Veränderungen anpassen. Als Verwandlungskünstler bereichert VEKSLE jeden Wohnraum. Die gesamte Serie ist unter Berücksichtigung der schnelllebigen und sich wandelnden Welt entworfen worden und beschreibt ein Konzept, bei dem sich alle Einzelteile kontinuierlich wechseln, pflegen und reparieren lassen. Die Kollektion ist den flexiblen Anforderungen des Menschen gewachsen, birgt für jeden die richtige Lösung und hinterlässt durch die Verwendung von natürlichen und recyclebaren Materialien nachhaltig Eindruck. KW - Stuhl KW - auswechseln KW - nachhaltig KW - recyclebar KW - reparierbar Y1 - 2023 PB - FH Aachen CY - Aachen ER - TY - THES A1 - Herrmann, Luna T1 - Blind Shopping N2 - Das Einkaufen in Einkaufszentren oder Ladenstraßen ist für Menschen ohne Sehbehinderung eine selbstverständliche Tätigkeit. Für Menschen mit Sehbehinderung gibt es bis heute keine Möglichkeit, sich ohne Hilfe von Familienmitgliedern, Freund:innen oder Pflegepersonal in einem Einkaufszentrum zurechtzufinden. Genau dieses Problem löst "NAVON.". Er ist ein intelligenter und smarter Blindenstock, welcher durch Ultraschalldistanzsensoren frühzeitig Hindernisse erkennt und die Möglichkeit bietet, den Betroffenen durch das Einkaufszentrum zu lotsen. Die Logik des Systems liegt innerhalb des Handgriffs, welcher die wichtigsten Einstellungen bzgl. Sprache und haptischer Bedienelemente steuert. Ebenfalls gibt er dem Betroffenen auch ein haptisches Feedback, um Hindernisse frühzeitig umgehen zu können. "NAVON." ist ein wichtiger Ansatz für eine neue Kategorie von Produkten und Blindenstöcken. Darüber hinaus birgt das Konzept auch weitere Potenziale für öffentliche Gebäude (Ämter, Krankenhäuser, etc..). KW - Inklusion KW - Sehbehinderung KW - Einkaufen KW - Hindernisse KW - Blindenstock Y1 - 2023 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER - TY - GEN A1 - Wiegner, J. A1 - Volker, H. A1 - Mainz, F. A1 - Backes, A. A1 - Löken, M. A1 - Hüning, Felix T1 - Wiegand-Effect-Powered Wireless IT Sensor Node N2 - With the growing interest in small distributed sensors for the “Internet of Things”, more attention is being paid to energy harvesting techologies. Reducing or eliminating the need for external power sources or batteries make devices more self-sufficient, more reliable, and reduces maintenance requirements. The Wiegand effect is a proven technology for harvesting small amounts of electrical power from mechanical motion. Y1 - 2022 N1 - PSMA International Energy Harvesting Workshop ~ 5-7 April 2022, Raleigh, NC, USA ER - TY - JOUR A1 - Gaigall, Daniel T1 - On the applicability of several tests to models with not identically distributed random effects JF - Statistics : A Journal of Theoretical and Applied Statistics N2 - We consider Kolmogorov–Smirnov and Cramér–von-Mises type tests for testing central symmetry, exchangeability, and independence. In the standard case, the tests are intended for the application to independent and identically distributed data with unknown distribution. The tests are available for multivariate data and bootstrap procedures are suitable to obtain critical values. We discuss the applicability of the tests to random effects models, where the random effects are independent but not necessarily identically distributed and with possibly unknown distributions. Theoretical results show the adequacy of the tests in this situation. The quality of the tests in models with random effects is investigated by simulations. Empirical results obtained confirm the theoretical findings. A real data example illustrates the application. KW - central symmetry test KW - exchangeability test KW - independence test KW - random effects KW - not identically distributed Y1 - 2023 SN - 0323-3944 U6 - https://doi.org/10.1080/02331888.2023.2193748 SN - 1029-4910 VL - 57 PB - Taylor & Francis CY - London ER - TY - CHAP A1 - Tran, Ngoc Trinh A1 - Trinh, Tu Luc A1 - Dao, Ngoc Tien A1 - Giap, Van Tan A1 - Truong, Manh Khuyen A1 - Dinh, Thuy Ha A1 - Staat, Manfred T1 - Limit and shakedown analysis of structures under random strength T2 - Proceedings of (NACOME2022) The 11th National Conference on Mechanics, Vol. 1. Solid Mechanics, Rock Mechanics, Artificial Intelligence, Teaching and Training N2 - Direct methods comprising limit and shakedown analysis is a branch of computational mechanics. It plays a significant role in mechanical and civil engineering design. The concept of direct method aims to determinate the ultimate load bearing capacity of structures beyond the elastic range. For practical problems, the direct methods lead to nonlinear convex optimization problems with a large number of variables and onstraints. If strength and loading are random quantities, the problem of shakedown analysis is considered as stochastic programming. This paper presents a method so called chance constrained programming, an effective method of stochastic programming, to solve shakedown analysis problem under random condition of strength. In this our investigation, the loading is deterministic, the strength is distributed as normal or lognormal variables. KW - Reliability of structures KW - Stochastic programming KW - Chance constrained programming KW - Shakedown analysis KW - Limit analysis Y1 - 2022 SN - 978-604-357-084-7 N1 - 11th National Conference on Mechanics (NACOME 2022), December 2-3, 2022, VNU University of Engineering and Technology, Hanoi, Vietnam SP - 510 EP - 518 PB - Nha xuat ban Khoa hoc tu nhien va Cong nghe (Verlag Naturwissenschaft und Technik) CY - Hanoi ER - TY - JOUR A1 - Gaigall, Daniel ED - AitSahlia, Farid T1 - Allocating and forecasting changes in risk JF - Journal of risk N2 - We consider time-dependent portfolios and discuss the allocation of changes in the risk of a portfolio to changes in the portfolio’s components. For this purpose we adopt established allocation principles. We also use our approach to obtain forecasts for changes in the risk of the portfolio’s components. To put the approach into practice we present an implementation based on the output of a simulation. Allocation is illustrated with an example portfolio in the context of Solvency II. The quality of the forecasts is investigated with an empirical study. KW - portfolio risk KW - allocation KW - forecast KW - covariance principle KW - conditional expectation principle Y1 - 2023 U6 - https://doi.org/10.21314/JOR.2022.048 SN - 1755-2842 SN - 1465-1211 VL - 25 IS - 3 SP - 1 EP - 24 PB - Infopro Digital Risk CY - London ER - TY - THES A1 - Tappert, Celine T1 - Die Zukunft des Energiemanagements : ein modulares Konzept und Design für verschiedene Nutzergruppen. N2 - Enma ist eine Energiemanagement-Anwendung, die verschiedene Nutzer:innengruppen zusammenführt und damit den Prozess vereinfacht. Die aktuelle Energiekrise betrifft insbesondere Unternehmen, die in der Energieerzeugung tätig sind. Die Digitalisierung wird für Unternehmen in der Zukunft immer wichtiger und sie werden sich ihr nicht entziehen können. Daher benötigen insbesondere Unternehmen, die keinen dedizierten Energiemanager:innen beschäftigen, gezielte Unterstützung von Anwendungen. Auch Vertriebspartner:innen und Hersteller:innen von Produkten wie PV-Anlagen und Stromspeichern, die von solch einer Anwendung profitieren können, wollen ihren Kunden:innen Sicherheit und Unterstützung bieten. Dafür ist eine Anwendung erforderlich, die dies vereint. Das Ziel war es, das Backend von OpenEMS (Energiemanagementsystems) zu nutzen und zusätzlich einen menschenzentrierten und umweltfreundlichen Ansatz zu bieten. Um die Anwendung realistischer zu gestalten, wurde sie in Kooperation mit dem Unternehmen Voltfang entwickelt. KW - Enma KW - Voltfang KW - OpenEMS KW - Energiemanagement KW - EMS Y1 - 2023 PB - FH Aachen CY - Aachen ER - TY - THES A1 - Stollenwerk, Hannah T1 - Rabbit Hole : welchen Einfluss digitale Plattformen auf rechte Radikalisierungsprozesse haben N2 - Obwohl 2019 als das Jahr rechtsterroristischer Anschläge weltweit gilt und die rechte Szene in den letzten Jahren auch in der gesellschaftlichen Mitte deutlich an Zuwachs gewinnen konnte, ist das Thema rund um rechtsextreme Online-Radikalisierung noch verhältnismäßig wenig erforscht. Laut Expert*innen ist dabei jeder Mensch potenziell für eine Radikalisierung anfällig, wenn es die Umstände begünstigen. Dass unsere Leben on- und offline immer weiter miteinander verschmelzen, erhöht die Gefahr für eine mögliche Radikalisierung zusätzlich. »Rabbit Hole« wurde als monothematisch erscheinende Bookazine-Reihe konzipiert, welche pro Ausgabe ein Thema rund um die Gefahren, Herausforderungen und Phänomene, die das Internet und digitale Plattformen mit sich bringen, beleuchtet. Sie soll zur Aufklärung von insbesondere jungen Erwachsenen beitragen. Die erste Ausgabe wurde beispielhaft ausgearbeitet. KW - Editorial Design KW - Typografie KW - Rabbit Hole KW - Bookazine KW - Online-Radikalisierung Y1 - 2023 PB - FH Aachen CY - Aachen ER - TY - THES A1 - Shafaghi, Shiva T1 - Zan, Zendegi, Azadi N2 - Das Projekt „Zan, Zendegi, Azadi" (Frau, Leben, Freiheit) setzt sich mit der aktuellen Situation im Iran auseinander. Bereits nach der Machtübernahme der islamischen Republik im Jahr 1979 wird die iranische Bevölkerung durch das brutale Regime unterdrückt und zum Schweigen gezwungen. Dieser Druck hat sich lange aufgestaut und nun gibt es seit Jahren in größeren Abständen Proteste gegen die Regierung. Der gewaltsame Tod der kurdischen Iranerin Mahsā Jîna Amīnī in Polizeigewahrsam am 16.09.2022 hat eine beispiellose Welle des Protests in allen Landesteilen Irans ausgelöst. Ihr Protest wird von Frauen angeführt und hat sich in eine beeindruckende Welle des Widerstands und der Rebellion entwickelt. Die unterschiedlichen Medien in diesem Projekt wie Dokumentarfotografie, Illustration, Projektion und Texte geben Betrachter:innen einen Eindruck der unmittelbaren Wirkung der revolutionären Ereignisse und der Reaktion des totalitären Regimes auf die Betroffenen. KW - Frau KW - Leben KW - Freiheit KW - Revolution KW - Iran Y1 - 2023 PB - FH Aachen CY - Aachen ER - TY - THES A1 - Schlappa, Anja T1 - Death & Decay : a journey into deathly oddities N2 - Wir werden alle eines Tages sterben. Obwohl – oder gerade weil – der Tod ein unausweichlicher Teil unseres Lebens ist, schreckt uns die Konversation über ihn und all seine Facetten ab, und die Furcht vor unserem eventuellen Ende bleibt bestehen. Jene Ehrfurcht hindert uns daran, das Ableben als mehr als nur den deprimierenden finalen Abschnitt unseres Seins zu betrachten. In ""Death & Decay"" wird sich mit den weniger bekannten Seiten des Todes auseinandergesetzt, denn das Ende unserer Existenz ist nicht gleich das Ende unserer Geschichte. Von kultureller Symbolik bis zu Tod unter unüblichen Umständen – ""Death & Decay"" nimmt Sie mit die Seiten des Todes kennenzulernen, die den meisten verborgen bleiben oder mit denen wir nie rechnen würden. KW - Tod KW - Verwesung KW - Leichen KW - Riten KW - Grabstaetten Y1 - 2023 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER - TY - THES A1 - Riederer, Estella Charlotte T1 - ITFS : Redesign des Erscheinungsbildes des Internationalen Trickfilm-Festival Stuttgart N2 - Film ab! Das Internationale Trickfilm-Festival Stuttgart ist seit 30 Jahren ein fester Bestandteil der internationalen Film- und Animations-Branche und zählt zu einer der renommiertesten Veranstaltungen. Das Festival ist ein Ort der Inspiration und des Austausches – die neusten Animationsfilme werden hier präsentiert, junge Talente entdeckt und gefördert. Im Fokus des neugestalteten Corporate Design steht die eigens entwickelte Schrift, welche den einzigartigen Charakter des Festivals widerspiegelt und so zum Trickfilm der Typografie wird. Das medienübergreifende Erscheinungsbild, in animierter oder statischer Form, kommuniziert so die qualitativ hochwertigen Inhalte des Festivals. Durch die dynamische und plakative Gestaltung wird das Festival zu einem unvergesslichen Erlebnis für alle Besucher:innen. KW - Redesign KW - Corporate Design KW - ITFS KW - Trickfilm-Festival KW - Stuttgart Y1 - 2023 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER - TY - THES A1 - Raring, Theresa T1 - Multimar Wattforum : die Entwicklung eines neuen Erscheinungsbildes N2 - Das Multimar Wattforum ist das größte Informationszentrum zum Thema Wattenmeer in Deutschland. Auf über 3000 Quadratmetern können große und kleine Besucher:innen eine interaktive Ausstellung über Wale, Watt und Weltnaturerbe bestaunen. Das Wattenmeer ist ein ganz besonderer Lebensraum und bietet vielen Lebewesen Zuflucht. Es wird durch die Gezeiten geprägt, bei Ebbe trocken und der Sonne ausgesetzt, bei Flut nass und salzig. Das neue Erscheinungsbild für das Multimar Wattforum soll die zentralen Werte und Alleinstellungsmerkmale hervorheben und dem Informationszentrum helfen, seiner Aufgabe als bildende, wissenschaftliche und schützende Einrichtung gerecht zu werden. So wurde ein einheitliches und skalierbares Erscheinungsbild und eine flexible Bild- und Wortmarke entwickel KW - Erscheinungsbild KW - Corporate Design KW - Branding KW - Wattenmeer KW - Wortmarke Y1 - 2023 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER - TY - THES A1 - Palm, Kevin John T1 - Viva sin Aqua : Konzeption einer Kampagne zum virtuellen Wasserbedarf N2 - Den aktuellen Zustand unserer Welt positiv zu beeinflussen, ist ein übergeordnetes Ziel, welches nur kollektiv als Gesellschaft erreicht werden kann. Das Einsparen von Ressourcen ist ein leichter Weg für jede einzelne Person, um ihren Beitrag für dieses Ziel zu leisten. Doch wie bewegt man die Bevölkerung zum Sparen? Und was soll eingespart werden? Die Kampagne "Viva sin Agua” sensibilisiert für die Ressource Wasser und nutzt dabei den öffentlichen Raum. Aufgeklärt wird über das sogenannte virtuelle Wasser. Dieses fällt in teilweise extremen Mengen für die Produktion jeglicher Konsumwaren an. Das Ziel der Kampagne ist das Kennzeichnen dieses Wasserverbrauchs direkt am Produkt über eigene Labels. Dadurch soll ein Bewusstsein für den kritischen Kontext geschaffen und das allgemeine Konsumverhalten nachhaltig verändert werden. KW - Wasserknappheit KW - Kampagne KW - Virtuelles Wasser KW - Latentes Wasser KW - Nachhaltigkeit Y1 - 2023 PB - FH Aachen CY - Aachen ER - TY - THES A1 - Outkina, Ioulia T1 - Kassandra : wetterbedingte Extremereignisse werden zunehmend die neue Realität bestimmen N2 - Wetterbedingte Extremereignisse nehmen mit dem Klimawandel in vielen Regionen der Welt an Intensität und Häufigkeit zu. Immer wieder unterstreichen tragische Krisenvorfälle die Notwendigkeit der Aufklärung im Nachgang. Doch ausgerechnet wenn sich Leute über eins der aktuellsten und schwerwiegendsten Themen unserer heutigen Zeit informieren wollen, wird es dafür keinen konsistenten Kanal in Deutschland geben. Kassandra bietet die Möglichkeit, sich verständlich mit den Ereignissen und Missständen sachlich im Krisenbereich auseinanderzusetzen. Transparenz und Seriosität sind Schwerpunkte im qualitativ hochwertigen Bereich, die dabei von Wichtigkeit sind. Mit den Prinzipien des investigativen Journalismus schafft Kassandra als Onlineformat einen Denkanstoß, wie im Bereich der Krisenkommunikation eine Verbesserung stattfinden kann. KW - UX KW - UI KW - Krise KW - klimakrise KW - klimawandel Y1 - 2023 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER - TY - THES A1 - Ostheimer, Johanna T1 - Somnio : ein aufklärendes Medium zum Thema Schlaf im 21. Jahrhundert N2 - Jede Nacht aufs Neue begeben wir uns in einen Zustand äußerer Ruhe. Unser Bewusstsein geht dabei ganz oder teilweise verloren, wir reagieren vermindert auf äußere Reize, die meisten unserer Körperfunktionen sind aufgehoben und am nächsten Morgen erinnern wir uns maximal an Bruchteile der letzten Stunden: Wir schlafen. Doch was genau passiert mit uns in dieser Zeit? Welche Vorteile bringt es uns zu schlafen? Welche Bedeutung haben unsere Träume? Und wieso steigt die Zahl an Menschen, die unter Schlafstörungen leiden, rapide an? In 'Somnio' wird diesen und weiteren Fragen auf den Grund gegangen und ein Blick in die Welt des Schlafs geboten. Ziel dieser Publikation ist es, Licht in eine oft noch unbekannte und gleichzeitig unglaubliche Welt zu bringen. Eine Welt, in der jeder von uns im Durchschnitt immerhin ein Drittel seines Lebens verbringt. KW - Illustration KW - Editorial Design KW - Publikation KW - schlafen KW - Schlafstörungen Y1 - 2023 PB - FH Aachen CY - Aachen ER - TY - CHAP A1 - Laack, Walter van ED - Ortmanns, Bruno ED - Brauers, Angelika T1 - Nahtoderfahrungen, Sterben und Tod aus der Perspektive von Medizin, Naturwissenschaften und Philosophie T2 - Thanatologie im deutschsprachigen Raum – Interdisziplinäre Perspektiven Y1 - 2023 SN - 978-3-98527-661-5 SP - 129 EP - 139 PB - Rediroma-Verlag ER - TY - JOUR A1 - Wiegner, Jonas A1 - Volker, Hanno A1 - Mainz, Fabian A1 - Backes, Andreas A1 - Loeken, Michael A1 - Hüning, Felix T1 - Energy analysis of a wireless sensor node powered by a Wiegand sensor JF - Journal of Sensors and Sensor Systems (JSSS) N2 - This article describes an Internet of things (IoT) sensing device with a wireless interface which is powered by the energy-harvesting method of the Wiegand effect. The Wiegand effect, in contrast to continuous sources like photovoltaic or thermal harvesters, provides small amounts of energy discontinuously in pulsed mode. To enable an energy-self-sufficient operation of the sensing device with this pulsed energy source, the output energy of the Wiegand generator is maximized. This energy is used to power up the system and to acquire and process data like position, temperature or other resistively measurable quantities as well as transmit these data via an ultra-low-power ultra-wideband (UWB) data transmitter. A proof-of-concept system was built to prove the feasibility of the approach. The energy consumption of the system during start-up was analysed, traced back in detail to the individual components, compared to the generated energy and processed to identify further optimization options. Based on the proof of concept, an application prototype was developed. Y1 - 2023 U6 - https://doi.org/10.5194/jsss-12-85-2023 SN - 2194-878X N1 - Corresponding author: Felix Hüning VL - 12 IS - 1 SP - 85 EP - 92 PB - Copernicus Publ. CY - Göttingen ER - TY - THES A1 - Oltmanns, Maireni T1 - Digitale Medien wollen gelernt sein : Kampagne für die "Medienscouts NRW" zur Kompetenzförderung N2 - ,,Digitale Medien wollen gelernt sein" ist eine Kampagne für das Projekt Medienscouts. Hier werden im ersten Schritt interessierte Schüler:innen an weiterführenden Schulen zu Medienexpert:innen ausgebildet. Im Zweiten geben sie ihr Wissen an ihre Mitschüler:innen weiter und fungieren in ihren Schulen als gleichaltrige Ansprechpartner:innen bei Fragen oder Problemen. Um weitere Schüler:innen für das Projekt zu werben, konzentriert sich die Kampagne auf eine altersgerechte Social Media-Präsenz. Ebenso wie das Projekt gibt auch die Kampagne den teilnehmenden Medienscouts die Freiheit, ihre Erfahrungen und Tipps zu teilen. Hierzu ist ein praktikables Konzept entworfen worden, mit dem die Scouts fortlaufend ihre offiziellen Kanäle bespielen können. KW - Medienkompetenz KW - Medienscouts KW - Social Media Kampagne Y1 - 2023 PB - FH Aachen CY - Aachen ER - TY - THES A1 - Krüger, Niklas A1 - Stupp, Anna-Lena T1 - Raubgut : Zusammenführung der in Deutschland befindlichen Objekte aus dem ehemaligen Königreich Benin N2 - Die Benin-Objekte wurden vor 126 Jahren durch britische Kolonialmächte aus ihrer Heimat geraubt. Sie wurden über die ganze Welt verstreut und ca. 1500 Stücke landeten auch in deutschen Museen. Bei den Objekten handelt es sich um das kulturelle Erbe und das Nationalarchiv eines Volkes. In „Raubgut“ finden die Leser:innen eine Zusammenführung aller Objekte, die sich in deutschen Museen befinden. „Raubgut“ ist das Ergebnis einer umfangreichen Recherche, in der die erste Zusammenführung auf bildlicher Ebene in einem Bildarchiv, auf textlicher Ebene u. a. in einer einzigartigen Inventarliste sowie in Texten zum ehemaligen Königreich, dem Kolonialismus und weiteren Themen gegeben ist. Nach all den Jahren wurde am 01. Juli 2022 die vollständige Eigentumsübertragung an Nigeria beschlossen. Ob das nun der Grundstein für die Entwicklung der Restitutionsdebatte war, wird sich in Zukunft zeigen. KW - Benin Bronzen KW - Rückgabe KW - Kulturgut KW - Museum KW - Sammlung Y1 - 2023 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER - TY - THES A1 - Laschet, Kimberly T1 - Berufsbegleitende Bildungsplattform für Designer : Lebenslanges Lernen für alle. N2 - Academia ist eine berufsbegleitende Bildungsplattform für Designer:innen. Die Mission der Plattform ist es, Designer:innen während ihres kreativen Ausbildungsweges und auch lange nach ihrem Berufseinstieg zu begleiten und zu unterstützen. Durch Videokurse, Online-Lehrveranstaltungen, etwa Gruppenseminare, Design Talks und Challenges sollen Nutzer:innen passend auf ihre Interessen und ihrem Niveau entsprechend gefördert werden. Academias Fokus liegt auf eine nachhaltige Weiterentwicklung der Fähigkeiten und der fachlichen Expertise. KW - Design KW - Lernen KW - Expertise KW - Weiterentwicklung KW - Kreativer Bildungsweg Y1 - 2023 PB - FH Aachen CY - Aachen ER - TY - THES A1 - Lorse, Hannah T1 - Gemüsevolle Aussichten : eine bunte Sammlung essbarer Pflanzenteile N2 - Die Bachelorarbeit „Gemüsevolle Aussichten“ / „Eine bunte Sammlung essbarer Pflanzenteile“ umfasst eine illustrative Auseinandersetzung, bunte Sammlung essbarer Pflanzenteile (Gemüse). Mit ihr entsteht ein visueller Anreiz, sich mehr mit dem gesunden Nahrungsmittel auseinanderzusetzen. Viele Kinder sowie Erwachsene kennen viele Gemüsesorten überhaupt nicht, Gemüse wie z. B. Schwarzwurzeln, Pastinaken oder gar Fenchel ist oftmals wenig bekannt. Mit der Arbeit wird ein informeller, illustrativer Überblick über Gemüse geschaffen, um zum Beispiel auch über die Inhaltsstoffe zu informieren. Denn viele wissen gar nicht, was eigentlich in dem wertvollen Nahrungsmitteln steckt, wie gut ein regelmäßiger Konsum von Gemüse eigentlich für uns ist. Dabei hat der tägliche Konsum von verschiedenen Gemüsesorten nicht nur eine Auswirkung auf die körperliche sondern auch auf die mentale Gesundheit. Viele Gemüsesorten beinhalten bestimmte Vitamine oder weitere Inhaltsstoffe, die sich positiv auf unsere Psyche auswirken und dazu beitragen, zum Bespiel einen depressiven Zustand zu verbessern. Auch die Umwelt kann von einem häufigeren Konsum von Gemüse anstatt Fleisch profitieren. Denn bei der Produktion von Fleisch entsteht viel mehr Kohlenstoffdioxid als bei der Produktion von Gemüse. Auch der Anteil des virtuellen Wassers ist bei der Produktion von Fleisch viel höher. Das Projekt besteht aus einem fadengebundenen Hardcover-Buch und einer Poster-Serie. Zu Beginn der Arbeit wird eine allgemeine Einleitung in das Thema Gemüse gegeben. Im folgenden Hauptteil werden verschiedene Gemüsegruppen und einige der zugehörigen Sorten visuell und informativ erklärt. Bei der Poster-Serie wurden die sechs Hauptfarben, die jeweiligen Gemüseillustrationen separiert und im Stil der Arbeit nummeriert benannt. Mit dem Projekt soll die Unwissenheit über viele Gemüsesorten gesenkt und der Konsum von weniger Fleisch und mehr Gemüse angeregt werden. KW - Gemüse KW - Pflanzenteile KW - Lebensmittel KW - Nahrung KW - Gesundheit Y1 - 2023 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER - TY - THES A1 - Kreutz, Delayne Sara T1 - Auf links gedreht : eine informative Auseinandersetzung mit der Benachteiligung durch Linkshändigkeit N2 - Unsere Welt funktioniert seit jeher völlig rechtsorientiert. Rechtshändigkeit stellt die Norm dar, während Linkshändigkeit eine Besonderheit ist – ein Phänomen, oder gar eine Kuriosität, welche im Laufe der Menschheitsgeschichte bei Weitem nicht so akzeptiert wurde wie in der Gegenwart. Das Buch „Auf links gedreht“ thematisiert die Wahrnehmung der linken Seite in der Vergangenheit und sensibilisiert für die Probleme von Linkshänder:innen in der heutigen Zeit. Ein Buch, fernab der Norm, mit einer Gestaltung ausgelegt auf die Linkshändigkeit. Es führt Rechtshänder:innen die Problematik vor Augen. So wird sich nicht nur inhaltlich für eine händigkeitsneutrale Gestaltung eingesetzt. Ein Buch über die linke Hand, gestaltet für die linke Hand. KW - Linkshändigkeit KW - Print KW - Publikation KW - Sachbuch KW - Editorial Y1 - 2023 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER - TY - THES A1 - Merkel, Tobias T1 - Unterstützung für Familien : barrierearme Inanspruchnahme von Sozialleistungen für Familien und Kinder N2 - Familienbezogene Sozialleistungen sind wichtige Bestandteile eines Sozialstaats: Nicht nur helfen sie Kindern und Familien bei der Bewältigung ihres Alltags, vielmehr sichern sie ein ̈würdevolles Zusammenleben, gleichen in Teilen soziale Unterschiede aus und korrigieren ungleiche Startchancen. Chancengleichheit ist kein triviales Thema: Eine Gesellschaft, die auf sozialen Grundpfeilern aufbaut, muss ständig die Umsetzung dieses eigenen Anspruchs bewerten. Finanzielle Mittel, die deswegen angeboten werden, sind nur dann wirksam, wenn sie Betroffene erreichen. 
Die Nicht-Inanspruchnahme von Sozialleistungen ist ein komplexes Problem. Als Ursache wird gemeinhin die Attraktivität der Leistungen genannt. Vielfach sind aber die Kommunikation und die Informationsbeschaffung entscheidende Faktoren, warum Hilfe ungenutzt bleibt. In dem Projekt ist demgemäß zu erörtern, wie über zeitgemäße digitale Instrumente das Angebot und die Leistungen der Familienkasse zugänglich, barrierearm und intuitiv gestaltet werden können. KW - Sozialleistungen KW - Familienkasse KW - Optimierung KW - Unterstützung KW - Informationsdesign Y1 - 2023 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER - TY - THES A1 - Martinez, Mariana T1 - The Taste of Memories : a recipe book of memories N2 - What does the word 'home' means and at what age do we give it meaning? Many of us grew up in one, in a home that our parents, grandparents, aunts, uncles and relatives shaped. Who, as we grew up, taught us about the world from their perspective as we interpreted and saw it for the first time and with it, its colors, its smells, its tastes, its sounds, its dances, and its languages. When we migrate, we take all that with us, like a piece of luggage that was stored in some corner inside a lung, or inside the memory in a heart’s artery. And then you arrive in this new world, which we were told was the Old World, with other colors, other flavors, other words, in which yours no longer make sense. And you try to connect with all your senses, but, above all, we try to belong, because we belonged all our lives to something, to someone, to some place where we learned to be. When we migrate, without saying, we go through the grieve that comes with the beautiful discomfort of leaving everything we once knew. We mourn, because we can’t go to lunch at our grandmas on Sundays, or have mom bring us soup when we are sick, or the Christmas meals and celebrations that we like so much, or that special dish that was made for us on our birthdays or on a family BBQ on a Sunday or a holiday. I wonder if emotions come inside us through the taste and respiratory track, if it is that we breathe life, and with that what we love finds its ways inside and finds its corner somewhere in the body. If what we have loved and what we have lived hides somewhere in our body, I doubtlessly think it came in through one of our senses, and in this attempt at my first illustrated book I’ll share which, I think, are the senses through which at first instance part of what we perceive as cultural identity enters. KW - Illustration KW - Heimat KW - Kindheit KW - Gehirn KW - Gerüche Y1 - 2023 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER - TY - THES A1 - Kouchev, Veronique T1 - Shiba Moments : 2D Adventure Story Game N2 - Shiba Moments ist ein 2D-Top-Down-Abenteuer Story-Spiel über die Wertschätzung der Zeit, die wir mit unseren Haustieren verbringen. Als Hundebesitzerin Conny wandert der / die Spieler:in durch eine Shiba-Traumwelt, die vergangene Momente mit ihrem Hund assoziieren und sich mit eigenen seltsamen Träumen vermischen. Die Spieler:innen erwartet eine Geschichte voller Emotionen, dunklem Humor und verrückter Ereignisse! KW - Computerspiel KW - 2D KW - Storytelling KW - Shiba Inu KW - niedlich Y1 - 2023 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER - TY - CHAP A1 - Thoma, Andreas A1 - Stiemer, Luc A1 - Braun, Carsten A1 - Fisher, Alex A1 - Gardi, Alessandro G. T1 - Potential of hybrid neural network local path planner for small UAV in urban environments T2 - AIAA SCITECH 2023 Forum N2 - This work proposes a hybrid algorithm combining an Artificial Neural Network (ANN) with a conventional local path planner to navigate UAVs efficiently in various unknown urban environments. The proposed method of a Hybrid Artificial Neural Network Avoidance System is called HANNAS. The ANN analyses a video stream and classifies the current environment. This information about the current Environment is used to set several control parameters of a conventional local path planner, the 3DVFH*. The local path planner then plans the path toward a specific goal point based on distance data from a depth camera. We trained and tested a state-of-the-art image segmentation algorithm, PP-LiteSeg. The proposed HANNAS method reaches a failure probability of 17%, which is less than half the failure probability of the baseline and around half the failure probability of an improved, bio-inspired version of the 3DVFH*. The proposed HANNAS method does not show any disadvantages regarding flight time or flight distance. Y1 - 2023 U6 - https://doi.org/10.2514/6.2023-2359 N1 - AIAA SCITECH 2023 Forum, 23-27 January 2023, National Harbor, Md & Online PB - AIAA CY - Reston, Va. ER - TY - THES A1 - Koch, Greta T1 - Eine monothematische Publikation zum Thema "Zeit" N2 - Zeit spielt in unser aller Leben eine allgegenwärtige Rolle. Sie ist immer da, war schon immer da und nimmt ihren Lauf, ganz egal was wir tun. Aber was macht die Zeit und was hat sie für einen Einfluss auf uns? Ist sie unsere ständige Begleiterin oder unsere »Gegnerin«? Wie unterschiedlich wir auf Zeit blicken können, was sie bewirkt und wie unser Umgang mit ihr das Leben beeinflusst, zeigt die Reihe an monothematischen Magazinen »about time«. Das Thema wird aus unterschiedlichsten Blickwinkeln beleuchtet und soll so eine gewisse Sensibilität für den Umgang mit der eigenen Zeit schaffen — denn sie ist am Ende das Wertvollste, das bleibt. KW - Magazin KW - Editorial KW - Sammlung KW - Print KW - Zeit Y1 - 2023 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER - TY - JOUR A1 - Dickhoff, Jens A1 - Horikawa, Atsushi A1 - Funke, Harald T1 - Hydrogen Combustion - new DLE Combustor Addresses NOx Emissions and Flashback JF - Turbomachinery international : the global journal of energy equipment Y1 - 2021 SN - 2767-2328 SN - 0149-4147 VL - 62 IS - 4 SP - 26 EP - 27 PB - MJH Life Sciences CY - Cranbury ER - TY - CHAP A1 - Horikawa, Atsushi A1 - Ashikaga, Mitsugu A1 - Yamaguchi, Masato A1 - Ogino, Tomoyuki A1 - Aoki, Shigeki A1 - Wirsum, Manfred A1 - Funke, Harald A1 - Kusterer, Karsten T1 - Combined heat and power supply demonstration of Micro-Mix Hydrogen Combustion Applied to M1A-17 Gas Turbine T2 - Proceedings of ASME Turbo Expo 2022: Turbomachinery Technical Conference and Exposition (GT2022) (Volume 3A) N2 - Kawasaki Heavy Industries, Ltd. (KHI), Aachen University of Applied Sciences, and B&B-AGEMA GmbH have investigated the potential of low NOx micro-mix (MMX) hydrogen combustion and its application to an industrial gas turbine combustor. Engine demonstration tests of a MMX combustor for the M1A-17 gas turbine with a co-generation system were conducted in the hydrogen-fueled power generation plant in Kobe City, Japan. This paper presents the results of the commissioning test and the combined heat and power (CHP) supply demonstration. In the commissioning test, grid interconnection, loading tests and load cut-off tests were successfully conducted. All measurement results satisfied the Japanese environmental regulation values. Dust and soot as well as SOx were not detected. The NOx emissions were below 84 ppmv at 15 % O2. The noise level at the site boundary was below 60 dB. The vibration at the site boundary was below 45 dB. During the combined heat and power supply demonstration, heat and power were supplied to neighboring public facilities with the MMX combustion technology and 100 % hydrogen fuel. The electric power output reached 1800 kW at which the NOx emissions were 72 ppmv at 15 % O2, and 60 %RH. Combustion instabilities were not observed. The gas turbine efficiency was improved by about 1 % compared to a non-premixed type combustor with water injection as NOx reduction method. During a total equivalent operation time of 1040 hours, all combustor parts, the M1A-17 gas turbine as such, and the co-generation system were without any issues. KW - industrial gas turbine KW - combustor development KW - fuels KW - hydrogen KW - emission Y1 - 2022 SN - 978-0-7918-8599-4 U6 - https://doi.org/10.1115/GT2022-81620 N1 - ASME Turbo Expo 2022: Turbomachinery Technical Conference and Exposition June 13–17, 2022 Rotterdam, Netherlands PB - American Society of Mechanical Engineers CY - Fairfield ER - TY - CHAP A1 - Möhren, Felix A1 - Bergmann, Ole A1 - Janser, Frank A1 - Braun, Carsten T1 - On the determination of harmonic propeller loads T2 - AIAA SCITECH 2023 Forum N2 - Dynamic loads significantly impact the structural design of propeller blades due to fatigue and static strength. Since propellers are elastic structures, deformations and aerodynamic loads are coupled. In the past, propeller manufacturers established procedures to determine unsteady aerodynamic loads and the structural response with analytical steady-state calculations. According to the approach, aeroelastic coupling primarily consists of torsional deformations. They neglect bending deformations, deformation velocities, and inertia terms. This paper validates the assumptions above for a General Aviation propeller and a lift propeller for urban air mobility or large cargo drones. Fully coupled reduced-order simulations determine the dynamic loads in the time domain. A quasi-steady blade element momentum approach transfers loads to one-dimensional finite beam elements. The simulation results are in relatively good agreement with the analytical method for the General Aviation propeller but show increasing errors for the slender lift propeller. The analytical approach is modified to consider the induced velocities. Still, inertia and velocity proportional terms play a significant role for the lift propeller due to increased elasticity. The assumption that only torsional deformations significantly impact the dynamic loads of propellers is not valid. Adequate determination of dynamic loads of such designs requires coupled aeroelastic simulations or advanced analytical procedures. Y1 - 2023 U6 - https://doi.org/10.2514/6.2023-2404 N1 - AIAA SCITECH 2023 Forum, 23-27 January 2023, National Harbor, Md & Online PB - AIAA ER - TY - GEN A1 - Hille, Sebastian A1 - Stumpf, Eike A1 - Mayntz, Joscha A1 - Dahmann, Peter T1 - Prediction of sound exposure caused by a landing motor glider with recuperating propellers T2 - AIAA SCITECH 2023 Forum N2 - This paper presents an approach to predicting the sound exposure on the ground caused by a landing aircraft with recuperating propellers. The noise source along the trajectory of a flight specified for a steeper approach is simulated based on measurements of sound power levels and additional parameters of a single propeller placed in a wind tunnel. To validate the measured data/measurement results, these simulations are also supported by overflight measurements of a test aircraft. It is shown that the simple source models of propellers do not provide fully satisfactory results since the sound levels are estimated too low. Nevertheless, with a further reference comparison, margins for an acceptable increase in the sound power level of the aircraft on its now steeper approach path could be estimated. Thus, in this case, a +7 dB increase in SWL would not increase the SEL compared to the conventional approach within only 2 km ahead of the airfield. Y1 - 2023 U6 - https://doi.org/10.2514/6.2023-0211 N1 - AIAA SCITECH 2023 Forum, 23-27 January 2023, National Harbor, Md & Online PB - AIAA CY - Reston, Va. ER - TY - JOUR A1 - Ringers, Christa A1 - Bialonski, Stephan A1 - Ege, Mert A1 - Solovev, Anton A1 - Hansen, Jan Niklas A1 - Jeong, Inyoung A1 - Friedrich, Benjamin M. A1 - Jurisch-Yaksi, Nathalie T1 - Novel analytical tools reveal that local synchronization of cilia coincides with tissue-scale metachronal waves in zebrafish multiciliated epithelia JF - eLife N2 - Motile cilia are hair-like cell extensions that beat periodically to generate fluid flow along various epithelial tissues within the body. In dense multiciliated carpets, cilia were shown to exhibit a remarkable coordination of their beat in the form of traveling metachronal waves, a phenomenon which supposedly enhances fluid transport. Yet, how cilia coordinate their regular beat in multiciliated epithelia to move fluids remains insufficiently understood, particularly due to lack of rigorous quantification. We combine experiments, novel analysis tools, and theory to address this knowledge gap. To investigate collective dynamics of cilia, we studied zebrafish multiciliated epithelia in the nose and the brain. We focused mainly on the zebrafish nose, due to its conserved properties with other ciliated tissues and its superior accessibility for non-invasive imaging. We revealed that cilia are synchronized only locally and that the size of local synchronization domains increases with the viscosity of the surrounding medium. Even though synchronization is local only, we observed global patterns of traveling metachronal waves across the zebrafish multiciliated epithelium. Intriguingly, these global wave direction patterns are conserved across individual fish, but different for left and right noses, unveiling a chiral asymmetry of metachronal coordination. To understand the implications of synchronization for fluid pumping, we used a computational model of a regular array of cilia. We found that local metachronal synchronization prevents steric collisions, i.e., cilia colliding with each other, and improves fluid pumping in dense cilia carpets, but hardly affects the direction of fluid flow. In conclusion, we show that local synchronization together with tissue-scale cilia alignment coincide and generate metachronal wave patterns in multiciliated epithelia, which enhance their physiological function of fluid pumping. Y1 - 2023 U6 - https://doi.org/10.7554/eLife.77701 SN - 2050-084X VL - 12 PB - eLife Sciences Publications ER - TY - JOUR A1 - Ulmer, Jessica A1 - Braun, Sebastian A1 - Cheng, Chi-Tsun A1 - Dowey, Steve A1 - Wollert, Jörg T1 - A human factors-aware assistance system in manufacturing based on gamification and hardware modularisation JF - International Journal of Production Research N2 - Assistance systems have been widely adopted in the manufacturing sector to facilitate various processes and tasks in production environments. However, existing systems are mostly equipped with rigid functional logic and do not provide individual user experiences or adapt to their capabilities. This work integrates human factors in assistance systems by adjusting the hardware and instruction presented to the workers’ cognitive and physical demands. A modular system architecture is designed accordingly, which allows a flexible component exchange according to the user and the work task. Gamification, the use of game elements in non-gaming contexts, has been further adopted in this work to provide level-based instructions and personalised feedback. The developed framework is validated by applying it to a manual workstation for industrial assembly routines. KW - Human factors KW - assistance system KW - gamification KW - adaptive systems KW - manufacturing Y1 - 2023 U6 - https://doi.org/10.1080/00207543.2023.2166140 SN - 0020-7543 (Print) SN - 1366-588X (Online) PB - Taylor & Francis ER - TY - JOUR A1 - Bergmann, Ole A1 - Möhren, Felix A1 - Braun, Carsten A1 - Janser, Frank T1 - On the influence of elasticity on swept propeller noise JF - AIAA SCITECH 2023 Forum N2 - High aerodynamic efficiency requires propellers with high aspect ratios, while propeller sweep potentially reduces noise. Propeller sweep and high aspect ratios increase elasticity and coupling of structural mechanics and aerodynamics, affecting the propeller performance and noise. Therefore, this paper analyzes the influence of elasticity on forward-swept, backward-swept, and unswept propellers in hover conditions. A reduced-order blade element momentum approach is coupled with a one-dimensional Timoshenko beam theory and Farassat's formulation 1A. The results of the aeroelastic simulation are used as input for the aeroacoustic calculation. The analysis shows that elasticity influences noise radiation because thickness and loading noise respond differently to deformations. In the case of the backward-swept propeller, the location of the maximum sound pressure level shifts forward by 0.5 °, while in the case of the forward-swept propeller, it shifts backward by 0.5 °. Therefore, aeroacoustic optimization requires the consideration of propeller deformation. Y1 - 2023 U6 - https://doi.org/10.2514/6.2023-0210 N1 - Session: Propeller, Open Rotor, and Rotorcraft Noise II AIAA SCITECH 2023 Forum, 23-27 January 2023, National Harbor, MD & Online PB - AIAA CY - Reston, Va. ER - TY - JOUR A1 - Böhnisch, Nils A1 - Braun, Carsten A1 - Muscarello, Vincenzo A1 - Marzocca, Pier T1 - A sensitivity study on aeroelastic instabilities of slender wings with a large propeller JF - AIAA SCITECH 2023 Forum N2 - Next-generation aircraft designs often incorporate multiple large propellers attached along the wingspan. These highly flexible dynamic systems can exhibit uncommon aeroelastic instabilities, which should be carefully investigated to ensure safe operation. The interaction between the propeller and the wing is of particular importance. It is known that whirl flutter is stabilized by wing motion and wing aerodynamics. This paper investigates the effect of a propeller onto wing flutter as a function of span position and mounting stiffness between the propeller and wing. The analysis of a comparison between a tractor and pusher configuration has shown that the coupled system is more stable than the standalone wing for propeller positions near the wing tip for both configurations. The wing fluttermechanism is mostly affected by the mass of the propeller and the resulting change in eigenfrequencies of the wing. For very weak mounting stiffnesses, whirl flutter occurs, which was shown to be stabilized compared to a standalone propeller due to wing motion. On the other hand, the pusher configuration is, as to be expected, the more critical configuration due to the attached mass behind the elastic axis. Y1 - 2023 U6 - https://doi.org/10.2514/6.2023-1893 N1 - AIAA SCITECH 2023 Forum, 23-27 January 2023, National Harbor, MD & Online SP - 1 EP - 14 PB - AIAA CY - Reston, Va. ER - TY - JOUR A1 - Liphardt, Anna-Maria A1 - Fernandez-Gonzalo, Rodrigo A1 - Albracht, Kirsten A1 - Rittweger, Jörn A1 - Vico, Laurence T1 - Musculoskeletal research in human space flight – unmet needs for the success of crewed deep space exploration JF - npj Microgravity N2 - Based on the European Space Agency (ESA) Science in Space Environment (SciSpacE) community White Paper “Human Physiology – Musculoskeletal system”, this perspective highlights unmet needs and suggests new avenues for future studies in musculoskeletal research to enable crewed exploration missions. The musculoskeletal system is essential for sustaining physical function and energy metabolism, and the maintenance of health during exploration missions, and consequently mission success, will be tightly linked to musculoskeletal function. Data collection from current space missions from pre-, during-, and post-flight periods would provide important information to understand and ultimately offset musculoskeletal alterations during long-term spaceflight. In addition, understanding the kinetics of the different components of the musculoskeletal system in parallel with a detailed description of the molecular mechanisms driving these alterations appears to be the best approach to address potential musculoskeletal problems that future exploratory-mission crew will face. These research efforts should be accompanied by technical advances in molecular and phenotypic monitoring tools to provide in-flight real-time feedback. Y1 - 2023 U6 - https://doi.org/10.1038/s41526-023-00258-3 SN - 2373-8065 VL - 9 IS - Article number: 9 SP - 1 EP - 9 PB - Springer Nature ER - TY - JOUR A1 - Funke, Harald A1 - Beckmann, Nils T1 - Flexible fuel operation of a Dry-Low-NOx Micromix Combustor with Variable Hydrogen Methane Mixture JF - International Journal of Gas Turbine, Propulsion and Power Systems N2 - The role of hydrogen (H2) as a carbon-free energy carrier is discussed since decades for reducing greenhouse gas emissions. As bridge technology towards a hydrogen-based energy supply, fuel mixtures of natural gas or methane (CH4) and hydrogen are possible. The paper presents the first test results of a low-emission Micromix combustor designed for flexible-fuel operation with variable H2/CH4 mixtures. The numerical and experimental approach for considering variable fuel mixtures instead of recently investigated pure hydrogen is described. In the experimental studies, a first generation FuelFlex Micromix combustor geometry is tested at atmospheric pressure at gas turbine operating conditions corresponding to part- and full-load. The H2/CH4 fuel mixture composition is varied between 57 and 100 vol.% hydrogen content. Despite the challenges flexible-fuel operation poses onto the design of a combustion system, the evaluated FuelFlex Micromix prototype shows a significant low NOx performance Y1 - 2022 SN - 1882-5079 VL - 13 IS - 2 SP - 1 EP - 7 ER - TY - JOUR A1 - Gaigall, Daniel A1 - Gerstenberg, Julian T1 - Cramér-von-Mises tests for the distribution of the excess over a confidence level JF - Journal of Nonparametric Statistics N2 - The Cramér-von-Mises distance is applied to the distribution of the excess over a confidence level. Asymptotics of related statistics are investigated, and it is seen that the obtained limit distributions differ from the classical ones. For that reason, quantiles of the new limit distributions are given and new bootstrap techniques for approximation purposes are introduced and justified. The results motivate new one-sample goodness-of-fit tests for the distribution of the excess over a confidence level and a new confidence interval for the related fitting error. Simulation studies investigate size and power of the tests as well as coverage probabilities of the confidence interval in the finite sample case. A practice-oriented application of the Cramér-von-Mises tests is the determination of an appropriate confidence level for the fitting approach. The adoption of the idea to the well-known problem of threshold detection in the context of peaks over threshold modelling is sketched and illustrated by data examples. KW - Cramér-von-Mises test KW - conditional excess distribution KW - confidence interval KW - goodness-of-fit test Y1 - 2023 U6 - https://doi.org/10.1080/10485252.2023.2173958 SN - 1048-5252 (Print) SN - 1029-0311 (Online) PB - Taylor & Francis ER - TY - JOUR A1 - Ayala, Rafael Ceja A1 - Harris, Isaac A1 - Kleefeld, Andreas A1 - Pallikarakis, Nikolaos T1 - Analysis of the transmission eigenvalue problem with two conductivity parameters JF - Applicable Analysis N2 - In this paper, we provide an analytical study of the transmission eigenvalue problem with two conductivity parameters. We will assume that the underlying physical model is given by the scattering of a plane wave for an isotropic scatterer. In previous studies, this eigenvalue problem was analyzed with one conductive boundary parameter whereas we will consider the case of two parameters. We prove the existence and discreteness of the transmission eigenvalues as well as study the dependence on the physical parameters. We are able to prove monotonicity of the first transmission eigenvalue with respect to the parameters and consider the limiting procedure as the second boundary parameter vanishes. Lastly, we provide extensive numerical experiments to validate the theoretical work. KW - Transmission Eigenvalues KW - Conductive Boundary Condition KW - Inverse Scattering Y1 - 2023 U6 - https://doi.org/10.1080/00036811.2023.2181167 SN - 0003-6811 PB - Taylor & Francis ER - TY - THES A1 - Jacobsen, Finn T1 - Designexperiments with Artificial Intelligence N2 - Künstliche Intelligenz (KI) hat die Designbranche erreicht, doch die Angst, dass KI Designer:innen die Arbeitsplätze wegnimmt, ist unbegründet. Künstliche Intelligenz kann Designer:innen als Werkzeug dienen. Durch das Zusammenspiel von Designer:innen und KI entstehen innerhalb von kürzester Zeit neuartige Kreationen. Das Projekt „Designexperiments with Artificial Intelligence“ ist eine Sammlung von visuellen Experimenten, welche mit der Hilfe von künstlicher Intelligenz durchgeführt wurden. Eines dieser Experimente wird in Form einer Installation ausgestellt. Dabei werden die Besucher*innen aufgefordert mit der Maschine zusammen ein Bild zu gestalten. Dieser Input wird anschließend von einer KI verarbeitet. Das Projekt „Designexperimente with Artificial Intelligence“ ist ein Versuch, mittels künstlicher Intelligenz eine neue Ästhetik zu finden. KW - Künstliche Intelligenz KW - Experimente KW - Installation KW - KI Kunst KW - Pix2Pix Y1 - 2023 PB - FH Aachen CY - Aachen ER - TY - THES A1 - Kappe, Lisa T1 - 59 von 47.900.000 Fußball-Fans N2 - Fan sein bedeutet für viele Menschen unterschiedliche Dinge. Viele würden sich selber vielleicht nicht mal als Solche bezeichnen. Nichtsdestotrotz gibt es etwas, das diese Gruppe von Menschen verbindet: Die gemeinsame Leidenschaft für eine bestimmte Sache, die sie im Alltag nicht missen wollen. In Deutschland alleine würden sich 47.900.000 Menschen selber als Fußball-Fan bezeichnen. Und natürlich lässt sich nicht jeder dieser Menschen in den selben Topf werfen. Die Publikation „59 von 47.900.00 Fußball-Fans“ beschäftigt sich mit 59 dieser Fans, verschiedenen Wissenschaftler*innen und Psycholog*innen, um dem Fan-Sein auf den Grund zu gehen. Warum sind Menschen überhaupt Fußball-Fans? Was macht Fan-Sein aus? Und wer sind diese Ultras? KW - Fans KW - Fußball KW - Fan-Kultur KW - Politik KW - Perspektive Y1 - 2023 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER - TY - THES A1 - Karry, Lena T1 - siso - lerne was du willst N2 - Kinder konsumieren heutzutage für viele Stunden am Tag soziale Medien. Jedoch sind die Inhalte auf diesen Plattformen oftmals nur oberflächlich und bieten wenig bis keinen Mehrwert durch z. B. zusätzliches Wissen. Dabei lernen Kinder einfacher, wenn ihr Interesse am Thema geweckt ist und sie Spaß an der Beschäftigung haben. Die individuellen Interessen der Kinder – und damit die möglichen Lerninhalte – sind vielfältig. Eine mögliche Lösung hierfür ist siso. Siso ist eine Lernplattform, die sich dadurch auszeichnet, dass Kinder ihren Interessen nachgehen sowie neue Fertigkeiten und Fähigkeiten erlernen können. Des Weiteren regt siso die Nutzer*innen durch Aufgaben dazu an, selbst aktiv zu werden. Durch die in der Anwendung verbaute soziale Komponente können Kinder sich auch über ihre Interessen austauschen und dadurch neue Freunde finden. KW - Lernen KW - Kinder KW - Interessen KW - Medienkompetenz KW - Eltern Y1 - 2023 PB - FH Aachen CY - Aachen ER - TY - THES A1 - Kauffmann, Michael T1 - OpenCouch : Therapiesuche leicht gemacht. N2 - Die Auswirkungen psychischer Erkrankungen stellen ein zunehmendes Thema in unserer Gesellschaft dar. Allein in Deutschland erkranken jedes Jahr ein Viertel aller Menschen psychisch. Besonders seit der Pandemie wächst die Nachfrage nach psychotherapeutischer Behandlung stetig an, wodurch die Wartelisten in den Praxen immer länger werden. Betroffene müssen oft ein halbes Jahr oder länger auf einen Therapieplatz warten und sind gezwungen zu nehmen, was gerade frei ist. Dabei ist es für den Therapieerfolg essenziell, dass nicht nur die Therapie auf einen abgestimmt ist, sondern auch die Chemie zwischen Therapeut:in und Patient:in passt. OpenCouch ist eine Anwendung, die Betroffene bei der Therapieplatzsuche unterstützen soll, indem sie Informationen und Tools zur Verfügung stellt, um trotz der geringen Verfügbarkeit einen Therapieplatz finden zu können, der einen Behandlungserfolg garantiert. KW - Psychotherapie KW - Therapieplatzsuche KW - Therapeutensuche KW - Mental Health KW - UX-Design Y1 - 2023 PB - FH Aachen CY - Aachen ER - TY - THES A1 - Keith, Anna-Lena T1 - KI und Sprache : explorativer Blick auf Word Embeddings im NLP N2 - Künstliche Intelligenz (KI) wird heute vielfältig eingesetzt, so auch im Bereich der Sprache. Persönliche Assistent:innen und Chatbots beeindrucken, da sie so etwas Vielschichtiges wie die menschliche Sprache beherrschen. Dass Maschinen dabei nur komplexen mathematischen Regeln folgen, ist den meisten klar. Doch was verbirgt sich hinter dem vermeintlichen „Sprachverständnis“ einer KI? Word Embeddings bilden eine numerische Repräsentation von Sprache ab und dienen einem Machine Learning Algorithmus als eine Art „Wortschatz“, mit dem gerechnet werden kann. Das Projekt bildet einen hundertdimensionalen Word Embedding Datensatz auf verschiedene Weise und mittels explorierbarer interaktiver Tools ab. Kombiniert mit Erklärungen und eigenen Erkenntnissen finden sich diese Tools in einem Blog, der fachfremden Einsteigenden ins Thema KI erste tiefergehende Einblicke „hinter die Kulissen“ bieten soll." KW - Datenvisualisierung KW - interaktiv KW - Generatives Design KW - Blog KW - Künstliche Intelligenz (KI) Y1 - 2023 PB - FH Aachen CY - Aachen ER - TY - THES A1 - Kieslich, Jasmina T1 - Roverandom : eine illustrative Aufarbeitung und Neuinterpretation des Kinderbuches von J.R.R Tolkien N2 - Die Geschichte „Roverandom“ von J.R.R Tolkien lädt auf eine spannende Reise an der Seite des kleinen Hundes Rover ein, welche zum Mond und in die Tiefsee, vorbei an Zauberern und Drachen führt. Um das Abenteuer Tolkiens neu aufleben zu lassen, befasst sich dieses Projekt mit der illustrativen Aufarbeitung der Geschichte. Auf Grundlage der Betrachtung von Inspirationen und eigenen Illustrationen des englischen Schriftstellers entwickelte sich eine einheitliche Gestaltung innerhalb des Projekts. Durch die Kombination analoger und digitaler Medien entstanden über 40 Illustrationen, welche verschiedenste Szenen visualisieren und so die Welt des kleinen Hundes Rover auf eine anschauliche Art und Weise darstellen. Die Geschichte „Roverandom“ wird so durch eine ganz eigene Bildsprache visuell begleitet und für interessierte Leser:innen neu geöffnet. KW - Illustration KW - Editorial KW - Roverandom KW - J.R.R Tolkien KW - analog Y1 - 2023 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER - TY - THES A1 - Heindrichs, Maik T1 - Intrinsic Motion in Type : eine Bewegtbild Plakatreihe für das Düsseldorfer Schauspielhaus N2 - Gestaltung und Programmierung dynamischer Motion-Design Plakate zwecks Kommunikation der Theaterstücke des Düsseldorfer Schauspielhauses. Der Fokus liegt dabei auf der Typografie und ihrer intrinsischen Bewegung. Der technische Fortschritt bietet viele neue Möglichkeiten im Umgang mit Schrift. Diese Arbeit dient dazu, mithilfe von aktuellen Techniken einen neuen Ansatz im Bereich Gestaltung mit Schrift, sowie Variable Fonts, in Kombination mit Motion-Design aufzuzeigen. Dies wird anhand von Eigenschaften der Schrift und der inhaltlichen Ebene, ohne die Buchstaben dabei zu dekonstruieren, umgesetzt. Die Bewegungen werden dann in das Format Plakat übertragen und dargestellt. KW - Bewegtbild KW - Plakat KW - Animation KW - Variable Schriften KW - Schriftvarianten Y1 - 2023 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER - TY - THES A1 - Fleißner, Annette Michaela T1 - Niemals gut genug : Narzissmus bei Frauen in der Mutter-Tochter-Beziehung N2 - Narzissmus ist ein vielgenutzter Begriff. Häufig wird er im Kontext toxischer Beziehungen verwendet. Nur selten wird das Leben von Frauen thematisiert, deren Mutter narzisstisch ist. Die Graphic Novel „Niemals gut genug“ leistet einen Beitrag zu diesem wenig beachteten Thema. „Niemals gut genug“ schildert anhand von illustrierten Kurzgeschichten alltägliche Situationen von Töchtern narzisstischer Mütter. Die Kurzgeschichten berücksichtigen die Vielfalt narzisstischer Persönlichkeitsstörungen und werfen ein Schlaglicht auf die Vergangenheit narzisstischer Mütter. Dadurch rückt auch die transgenerationale Weitergabe von Narzissmus in den Fokus. „Niemals gut genug“ stellt einen einfühlsamen Zugang zu diesem sensiblen Thema dar und hilft dadurch Betroffenen beim Verstehen und Genesen. KW - Narzissmus KW - Mutter KW - Familie KW - Psychologie KW - Illustration Y1 - 2023 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER - TY - THES A1 - Farjam, Ina T1 - Farfilia : experimenteller Tanzfilm über eine Vater-Tochter-Beziehung N2 - Der experimentelle Tanzfilm „Farfilia“ behandelt die Beziehung einer Tochter zu ihrem Vater. Beide Parteien funktionieren sehr unterschiedlich, denken, kommunizieren und leben in völlig verschiedenen Welten. Es findet ein Konflikt zwischen den Generationen statt, zwischen zwei sehr gegensätzlichen Prägungen und Charakteren. Die zwei Welten unterscheiden sich nicht nur in ihrer Visualität, sondern durch die in ihr lebenden und handelnden zwei Hauptprotagonist*innen, welches bildgestalterisch durch ein Zusammenspiel von Cinematographie, Choreographie und Setting ausgearbeitet und dargestellt wird. Durch die gemeinsame Wirkung vieler unterschiedlicher Gestaltungsmittel soll eine Geschichte erzählt werden, in der sich beide Welten aufeinander zu bewegen und am Ende Elemente der jeweils anderen Welt in sich aufnehmen und für die eigene Empfindung in der jeweiligen Umgebung adaptieren. KW - Experimentalfilm KW - Vater KW - Tochter KW - Tanz KW - Abstrakt Y1 - 2023 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER - TY - THES A1 - Eilert, Denny T1 - Massenwohnungsbau in Berlin : eine Publikation zur Architektur des Massenwohnungsbaus in Berlin N2 - Berlin. Eine Stadt, die immer weiter wächst und beinahe aus allen Nähten platzt. Doch das Problem ist kein neues, denn bereits seit den 1920er-Jahren ist der Wohnraummangel in Berlin ein bekanntes Thema und immer wieder mussten hierfür in den letzten 100 Jahren Lösungen gefunden werden. Diese Publikation dokumentiert einen Querschnitt der Massenwohnbauten in Berlin, welche seit dem ersten Weltkrieg und auch insbesondere nach der Teilung der Stadt für die Unterbringung großer Menschenmengen konzipiert und gebaut wurden. Das Buch klärt über die Entstehung der Viertel und Gebäude auf, enthält Interviews einiger Bewohner*innen und bietet zudem fotografisch einen Blick hinter die Fassaden. Das Ziel ist es, das Thema Massenwohnraum vorzustellen und durch die detaillierten Einblicke die damit verknüpften – meist negativen – Stigmata abzubauen. KW - Sozialer Wohnungsbau KW - Architektur KW - Editorial-Design KW - Typografie KW - Fotografie Y1 - 2023 PB - FH Aachen CY - Aachen ER - TY - JOUR A1 - Schöning, Michael Josef A1 - Bronder, Thomas A1 - Wu, Chunsheng A1 - Scheja, Sabrina A1 - Jessing, Max A1 - Metzger-Boddien, Christoph A1 - Keusgen, Michael A1 - Poghossian, Arshak T1 - Label-Free DNA Detection with Capacitive Field-Effect Devices—Challenges and Opportunities JF - Proceedings N2 - Field-effect EIS (electrolyte-insulator-semiconductor) sensors modified with a positively charged weak polyelectrolyte layer have been applied for the electrical detection of DNA (deoxyribonucleic acid) immobilization and hybridization by the intrinsic molecular charge. The EIS sensors are able to detect the existence of target DNA amplicons in PCR (polymerase chain reaction) samples and thus, can be used as tool for a quick verification of DNA amplification and the successful PCR process. Due to their miniaturized setup, compatibility with advanced micro- and nanotechnologies, and ability to detect biomolecules by their intrinsic molecular charge, those sensors can serve as possible platform for the development of label-free DNA chips. Possible application fields as well as challenges and limitations will be discussed. Y1 - 2017 U6 - https://doi.org/10.3390/proceedings1080719 SN - 2504-3900 N1 - This article belongs to the Proceedings of "Proceedings of the 5th International Symposium on Sensor Science (I3S 2017)" VL - 1 IS - 8 SP - Artikel 719 PB - MDPI CY - Basel ER - TY - CHAP A1 - Gömmel, Andreas A1 - Frauenrath, Tobias A1 - Otten, Mario A1 - Niendorf, Thoralf A1 - Butenweg, Christoph ED - Möser, Michael ED - Schulte-Fortkamp, Brgitte ED - Ochmann, Martin T1 - In-vivo measurements of vocal fold geometry using Magnetic Resonance Imaging T2 - Fortschritte der Akustik - DAGA 2010, 36. Jahrestagung für Akustik Y1 - 2010 SN - 978-3-9808659-8-2 PB - Deutsche Gesellschaft für Akustik CY - Berlin ER - TY - BOOK A1 - Laack, Walter van T1 - Aufruf zum Nachdenken: Corona und neue Kriege – Wie kann die Menschheit überleben? T1 - Call for Reflection: Corona and New Wars – How can Mankind survive? Y1 - 2022 SN - 978-3-936624-56-4 N1 - Dritter Band der Buchreihe “Vorträge & Einsichten – Lectures & Insights” und hier das zweite “Upside-Down-Buch”: Deutsche und englische Version in einem Buch. PB - van Laack GmbH CY - Aachen ER - TY - BOOK A1 - Laack, Walter van T1 - Schnittstelle Tod: Was lernen wir durch Corona über Leben und Tod? Y1 - 2022 SN - 978-3-936624-53-3 N1 - Siebter Tagungsband aus der Buchreihe “Schnittstelle Tod” PB - van Laack GmbH CY - Aachen ER - TY - BOOK A1 - Laack, Walter van T1 - Greater Than the Entire Universe Y1 - 2022 SN - 978-3-936624-52-6 PB - van Laack GmbH CY - Aachen ER - TY - CHAP A1 - Butenweg, Christoph A1 - Marinković, Marko A1 - Pavese, Alberto A1 - Lanese, Igor A1 - Hoffmeister, Benno A1 - Pinkawa, Marius A1 - Vulcu, Mihai-Cristian A1 - Bursi, Oreste A1 - Nardin, Chiara A1 - Paolacci, Fabrizio A1 - Quinci, Gianluca A1 - Fragiadakis, Michalis A1 - Weber, Felix A1 - Huber, Peter A1 - Renault, Philippe A1 - Gündel, Max A1 - Dyke, Shirley A1 - Ciucci, M. A1 - Marino, A. T1 - Seismic performance of multi-component systems in special risk industrial facilities T2 - Proceedings of the seventeenth world conference on earthquake engineering N2 - Past earthquakes demonstrated the high vulnerability of industrial facilities equipped with complex process technologies leading to serious damage of the process equipment and multiple and simultaneous release of hazardous substances in industrial facilities. Nevertheless, the design of industrial plants is inadequately described in recent codes and guidelines, as they do not consider the dynamic interaction between the structure and the installations and thus the effect of seismic response of the installations on the response of the structure and vice versa. The current code-based approach for the seismic design of industrial facilities is considered not enough for ensure proper safety conditions against exceptional event entailing loss of content and related consequences. Accordingly, SPIF project (Seismic Performance of Multi- Component Systems in Special Risk Industrial Facilities) was proposed within the framework of the European H2020 - SERA funding scheme (Seismology and Earthquake Engineering Research Infrastructure Alliance for Europe). The objective of the SPIF project is the investigation of the seismic behavior of a representative industrial structure equipped with complex process technology by means of shaking table tests. The test structure is a three-story moment resisting steel frame with vertical and horizontal vessels and cabinets, arranged on the three levels and connected by pipes. The dynamic behavior of the test structure and installations is investigated with and without base isolation. Furthermore, both firmly anchored and isolated components are taken into account to compare their dynamic behavior and interactions with each other. Artificial and synthetic ground motions are applied to study the seismic response at different PGA levels. After each test, dynamic identification measurements are carried out to characterize the system condition. The contribution presents the numerical simulations to calibrate the tests on the prototype, the experimental setup of the investigated structure and installations, selected measurement data and finally describes preliminary experimental results. KW - industrial facilities KW - piping KW - installations KW - seismic loading KW - earthquakes Y1 - 2021 N1 - 17. World Conference on Earthquake Engineering, 17WCEE, Sendai, Japan, 2021-09-27 - 2021-10-02 ER - TY - CHAP A1 - Taddei, Francesca A1 - Lozana, Lara A1 - Michel, Philipp A1 - Butenweg, Christoph A1 - Klinkel, Sven ED - Papadrakakis, Manolis ED - Papadrakakis, M. ED - Papadopoulos, V. ED - Plevris, V. T1 - Practical recommendations for the foundation design of onshore wind turbines including soil-structure interaction T2 - 5th International Conference on Computational Methods in Structural , Hersonissos, Greece Dynamics and Earthquake Engineering, COMPDYN 2015, 25.05.2015-27.05.2015, Hersonissos, Greece. Y1 - 2015 ER - TY - JOUR A1 - Welden, Rene A1 - Jablonski, Melanie A1 - Wege, Christina A1 - Keusgen, Michael A1 - Wagner, Patrick Hermann A1 - Wagner, Torsten A1 - Schöning, Michael Josef T1 - Light-Addressable Actuator-Sensor Platform for Monitoring and Manipulation of pH Gradients in Microfluidics: A Case Study with the Enzyme Penicillinase JF - Biosensors N2 - The feasibility of light-addressed detection and manipulation of pH gradients inside an electrochemical microfluidic cell was studied. Local pH changes, induced by a light-addressable electrode (LAE), were detected using a light-addressable potentiometric sensor (LAPS) with different measurement modes representing an actuator-sensor system. Biosensor functionality was examined depending on locally induced pH gradients with the help of the model enzyme penicillinase, which had been immobilized in the microfluidic channel. The surface morphology of the LAE and enzyme-functionalized LAPS was studied by scanning electron microscopy. Furthermore, the penicillin sensitivity of the LAPS inside the microfluidic channel was determined with regard to the analyte’s pH influence on the enzymatic reaction rate. In a final experiment, the LAE-controlled pH inhibition of the enzyme activity was monitored by the LAPS. KW - microfluidics KW - enzyme kinetics KW - actuator-sensor system KW - light-addressable electrode KW - light-addressable potentiometric sensor Y1 - 2021 U6 - https://doi.org/10.3390/bios11060171 SN - 2079-6374 N1 - This article belongs to the Special Issue "Selected Papers from the 1st International Electronic Conference on Biosensors (IECB 2020)" VL - 11 IS - 6 PB - MDPI CY - Basel ER - TY - JOUR A1 - Welden, Melanie A1 - Poghossian, Arshak A1 - Vahidpour, Farnoosh A1 - Wendlandt, Tim A1 - Keusgen, Michael A1 - Wege, Christina A1 - Schöning, Michael Josef T1 - Towards multi-analyte detection with field-effect capacitors modified with tobacco mosaic virus bioparticles as enzyme nanocarriers JF - Biosensors N2 - Utilizing an appropriate enzyme immobilization strategy is crucial for designing enzyme-based biosensors. Plant virus-like particles represent ideal nanoscaffolds for an extremely dense and precise immobilization of enzymes, due to their regular shape, high surface-to-volume ratio and high density of surface binding sites. In the present work, tobacco mosaic virus (TMV) particles were applied for the co-immobilization of penicillinase and urease onto the gate surface of a field-effect electrolyte-insulator-semiconductor capacitor (EISCAP) with a p-Si-SiO₂-Ta₂O₅ layer structure for the sequential detection of penicillin and urea. The TMV-assisted bi-enzyme EISCAP biosensor exhibited a high urea and penicillin sensitivity of 54 and 85 mV/dec, respectively, in the concentration range of 0.1–3 mM. For comparison, the characteristics of single-enzyme EISCAP biosensors modified with TMV particles immobilized with either penicillinase or urease were also investigated. The surface morphology of the TMV-modified Ta₂O₅-gate was analyzed by scanning electron microscopy. Additionally, the bi-enzyme EISCAP was applied to mimic an XOR (Exclusive OR) enzyme logic gate. KW - urease KW - enzyme-logic gate KW - bi-enzyme biosensor KW - capacitive field-effect sensor KW - tobacco mosaic virus (TMV) KW - penicillinase Y1 - 2022 U6 - https://doi.org/10.3390/bios12010043 SN - 2079-6374 N1 - This article belongs to the Special Issue "Biosensors: 10th Anniversary Feature Papers" VL - 12 IS - 1 PB - MDPI CY - Basel ER - TY - JOUR A1 - Zhantlessova, Sirina A1 - Savitskaya, Irina A1 - Kistaubayeva, Aida A1 - Ignatova, Ludmila A1 - Talipova, Aizhan A1 - Pogrebnjak, Alexander A1 - Digel, Ilya T1 - Advanced “Green” prebiotic composite of bacterial cellulose/pullulan based on synthetic biology-powered microbial coculture strategy JF - Polymers N2 - Bacterial cellulose (BC) is a biopolymer produced by different microorganisms, but in biotechnological practice, Komagataeibacter xylinus is used. The micro- and nanofibrillar structure of BC, which forms many different-sized pores, creates prerequisites for the introduction of other polymers into it, including those synthesized by other microorganisms. The study aims to develop a cocultivation system of BC and prebiotic producers to obtain BC-based composite material with prebiotic activity. In this study, pullulan (PUL) was found to stimulate the growth of the probiotic strain Lactobacillus rhamnosus GG better than the other microbial polysaccharides gellan and xanthan. BC/PUL biocomposite with prebiotic properties was obtained by cocultivation of Komagataeibacter xylinus and Aureobasidium pullulans, BC and PUL producers respectively, on molasses medium. The inclusion of PUL in BC is proved gravimetrically by scanning electron microscopy and by Fourier transformed infrared spectroscopy. Cocultivation demonstrated a composite effect on the aggregation and binding of BC fibers, which led to a significant improvement in mechanical properties. The developed approach for “grafting” of prebiotic activity on BC allows preparation of environmentally friendly composites of better quality. KW - coculture KW - pullulan KW - exopolysaccharides KW - prebiotic KW - bacterial cellulose Y1 - 2022 U6 - https://doi.org/10.3390/polym14153224 SN - 2073-4360 N1 - This article belongs to the Special Issue "Cellulose Based Composites" VL - 14 IS - 15 PB - MDPI CY - Basel ER - TY - JOUR A1 - Ojovan, Michael I. A1 - Steinmetz, Hans-Jürgen T1 - Approaches to Disposal of Nuclear Waste JF - Energies N2 - We present a concise mini overview on the approaches to the disposal of nuclear waste currently used or deployed. The disposal of nuclear waste is the end point of nuclear waste management (NWM) activities and is the emplacement of waste in an appropriate facility without the intention to retrieve it. The IAEA has developed an internationally accepted classification scheme based on the end points of NWM, which is used as guidance. Retention times needed for safe isolation of waste radionuclides are estimated based on the radiotoxicity of nuclear waste. Disposal facilities usually rely on a multi-barrier defence system to isolate the waste from the biosphere, which comprises the natural geological barrier and the engineered barrier system. Disposal facilities could be of a trench type, vaults, tunnels, shafts, boreholes, or mined repositories. A graded approach relates the depth of the disposal facilities’ location with the level of hazard. Disposal practices demonstrate the reliability of nuclear waste disposal with minimal expected impacts on the environment and humans. KW - borehole disposal KW - geological disposal KW - disposal facility KW - retention time KW - nuclear waste Y1 - 2022 U6 - https://doi.org/10.3390/en15207804 SN - 1996-1073 N1 - This article belongs to the Special Issue "Treatment of Radioactive Waste and Sustainability Energy" VL - 15 IS - 20 PB - MDPI CY - Basel ER - TY - CHAP A1 - Welden, Melanie A1 - Severins, Robin A1 - Poghossian, Arshak A1 - Wege, Christina A1 - Siegert, Petra A1 - Keusgen, Michael A1 - Schöning, Michael Josef T1 - Studying the immobilization of acetoin reductase with Tobacco mosaic virus particles on capacitive field-effect sensors T2 - 2022 IEEE International Symposium on Olfaction and Electronic Nose (ISOEN) N2 - A capacitive electrolyte-insulator-semiconductor (EISCAP) biosensor modified with Tobacco mosaic virus (TMV) particles for the detection of acetoin is presented. The enzyme acetoin reductase (AR) was immobilized on the surface of the EISCAP using TMV particles as nanoscaffolds. The study focused on the optimization of the TMV-assisted AR immobilization on the Ta 2 O 5 -gate EISCAP surface. The TMV-assisted acetoin EISCAPs were electrochemically characterized by means of leakage-current, capacitance-voltage, and constant-capacitance measurements. The TMV-modified transducer surface was studied via scanning electron microscopy. KW - Tobacco mosaic virus KW - acetoin KW - capacitive field-effect biosensor KW - enzyme immobilization Y1 - 2022 SN - 978-1-6654-5860-3 (Online) SN - 978-1-6654-5861-0 (Print) U6 - https://doi.org/10.1109/ISOEN54820.2022.9789657 N1 - IEEE International Symposium on Olfaction and Electronic Nose (ISOEN), 29 May 2022 - 01 June 2022, Aveiro, Portugal. PB - IEEE ER - TY - JOUR A1 - Welden, Melanie A1 - Severins, Robin A1 - Poghossian, Arshak A1 - Wege, Christina A1 - Bongaerts, Johannes A1 - Siegert, Petra A1 - Keusgen, Michael A1 - Schöning, Michael Josef T1 - Detection of acetoin and diacetyl by a tobacco mosaic virus-assisted field-effect biosensor JF - Chemosensors N2 - Acetoin and diacetyl have a major impact on the flavor of alcoholic beverages such as wine or beer. Therefore, their measurement is important during the fermentation process. Until now, gas chromatographic techniques have typically been applied; however, these require expensive laboratory equipment and trained staff, and do not allow for online monitoring. In this work, a capacitive electrolyte–insulator–semiconductor sensor modified with tobacco mosaic virus (TMV) particles as enzyme nanocarriers for the detection of acetoin and diacetyl is presented. The enzyme acetoin reductase from Alkalihalobacillus clausii DSM 8716ᵀ is immobilized via biotin–streptavidin affinity, binding to the surface of the TMV particles. The TMV-assisted biosensor is electrochemically characterized by means of leakage–current, capacitance–voltage, and constant capacitance measurements. In this paper, the novel biosensor is studied regarding its sensitivity and long-term stability in buffer solution. Moreover, the TMV-assisted capacitive field-effect sensor is applied for the detection of diacetyl for the first time. The measurement of acetoin and diacetyl with the same sensor setup is demonstrated. Finally, the successive detection of acetoin and diacetyl in buffer and in diluted beer is studied by tuning the sensitivity of the biosensor using the pH value of the measurement solution. Y1 - 2022 U6 - https://doi.org/10.3390/chemosensors10060218 SN - 2227-9040 N1 - This article belongs to the Special Issue "Nanostructured Devices for Biochemical Sensing" VL - 10 IS - 6 PB - MDPI CY - Basel ER - TY - JOUR A1 - Haeger, Gerrit A1 - Bongaerts, Johannes A1 - Siegert, Petra T1 - A convenient ninhydrin assay in 96-well format for amino acid-releasing enzymes using an air-stable reagent JF - Analytical Biochemistry N2 - An improved and convenient ninhydrin assay for aminoacylase activity measurements was developed using the commercial EZ Nin™ reagent. Alternative reagents from literature were also evaluated and compared. The addition of DMSO to the reagent enhanced the solubility of Ruhemann's purple (RP). Furthermore, we found that the use of a basic, aqueous buffer enhances stability of RP. An acidic protocol for the quantification of lysine was developed by addition of glacial acetic acid. The assay allows for parallel processing in a 96-well format with measurements microtiter plates. Y1 - 2022 U6 - https://doi.org/10.1016/j.ab.2022.114819 SN - 1096-0309 IS - 624 PB - Elsevier CY - Amsterdam ER - TY - JOUR A1 - Falkenberg, Fabian A1 - Bott, Michael A1 - Bongaerts, Johannes A1 - Siegert, Petra T1 - Phylogenetic survey of the subtilase family and a data-mining-based search for new subtilisins from Bacillaceae JF - Frontiers in Microbiology N2 - The subtilase family (S8), a member of the clan SB of serine proteases are ubiquitous in all kingdoms of life and fulfil different physiological functions. Subtilases are divided in several groups and especially subtilisins are of interest as they are used in various industrial sectors. Therefore, we searched for new subtilisin sequences of the family Bacillaceae using a data mining approach. The obtained 1,400 sequences were phylogenetically classified in the context of the subtilase family. This required an updated comprehensive overview of the different groups within this family. To fill this gap, we conducted a phylogenetic survey of the S8 family with characterised holotypes derived from the MEROPS database. The analysis revealed the presence of eight previously uncharacterised groups and 13 subgroups within the S8 family. The sequences that emerged from the data mining with the set filter parameters were mainly assigned to the subtilisin subgroups of true subtilisins, high-alkaline subtilisins, and phylogenetically intermediate subtilisins and represent an excellent source for new subtilisin candidates. Y1 - 2022 U6 - https://doi.org/10.3389/fmicb.2022.1017978 SN - 1664-302X VL - 2022 IS - 13 PB - Frontiers CY - Lausanne ER - TY - CHAP A1 - Altay, Okyay A1 - Butenweg, Christoph A1 - Klinkel, Sven T1 - Vibration mitigation of wind turbine towers by a new semiactive Tuned Liquid Column Damper T2 - 6. Word Congress on Structural Control and Monitoring, 15 - 17 July, 2014 Barcelona,Spain Y1 - 2014 ER - TY - THES A1 - Dorn, Aileen Sakura T1 - Effizienz und Gesundheitsförderung im Krankenhaus : Dienstplanung im Krankenhaus unter Berücksichtigung der berufsbedingten psychischen und physischen Gesundheit des Klinikpersonals N2 - Dass der Stress im Krankenhaus eine Belastung für das Klinikpersonal darstellt, ist eine allseits bekannte Tatsache. Das liegt an dem anstrengenden Klinikalltag, welcher die Mitarbeiter:innen auf Belastungsprobe stellt. Lange Dienste und Überstunden, wenig Pausen und hohe Arbeitsverdichtung, Nacht- und Schichtdienst, zudem auch die aufwendige Dokumentation und ̈Bürokratie. Timewise behandelt die Thematik der Dienstplanerstellung im Krankenhaus unter der Berücksichtigung der psychischen und physischen Gesundheit des Klinikpersonals im Nacht- und Schichtdienst. Essenzielle Funktionen sind kürzere Kommunikationswege und eine gute Übersicht über den Soll-Ist-Abgleich inklusive Überstunden, Minusstunden, Abwesenheiten und den monatlichen Lohn. Der einfache Schichttausch und die Option der Berücksichtigung individueller Präferenzen und Wünsche ermöglicht es dem Personal, die Arbeit und das private Leben besser miteinander vereinen zu können, was sich positiv auf die Arbeitszufriedenheit auswirkt. KW - Dienstplanung KW - Gesundheitsförderung KW - Effizienz KW - Prävention KW - Schichtarbeit Y1 - 2023 PB - FH Aachen CY - Aachen ER - TY - CHAP A1 - Altay, Okyay A1 - Butenweg, Christoph A1 - Klinkel, Sven T1 - Vibration control of slender structures by semi-active tuned liquid column dampers T2 - Conference of the ASCE Engineering Mechanics Institute , Evanston, IL , USA , EMI 2013 , 2013-08-04 - 2013-08-07 Y1 - 2013 N1 - http://www.emi2013.northwestern.edu/openconf/modules/request.php?module=oc_program&action=view.php&a=&id=213&type=1 Seite kann nicht gefunden werden. ER - TY - CHAP A1 - Butenweg, Christoph A1 - Norda, Hannah ED - Adam, Christoph ED - Heuer, Rudolf ED - Lenhardt, Wolfgang ED - Schranz, Christian T1 - Nonlinear analysis of masonry structures according to Eurocode 8 T2 - Proceedings - Vienna Congress on Recent Advances in Earthquake Engineering and Structural Dynamics 2013 (VEESD 2013) Y1 - 2013 SN - 978-3-902749-04-8 N1 - Vienna Congress on Recent Advances in Earthquake Engineering and Structural Dynamics, Vienna, Austria, Paper No. 523 13. D-A-CH Tagung ; Vienna, Austria, 29. - 30. August 2013 http://hdl.handle.net/20.500.12188/15830 (Error - Cannot Connect to Server) ER - TY - CHAP A1 - Churilov, Sergej A1 - Dumova-Jovanoska, Elena A1 - Butenweg, Christoph ED - Adam, Christoph ED - Heuer, Rudolf ED - Lenhardt, Wolfgang ED - Schranz, Christian T1 - Seismic verification of existing masonry buildings and strengthening with reinforced concrete jackets T2 - Proceedings - Vienna Congress on Recent Advances in Earthquake Engineering and Structural Dynamics 2013 (VEESD 2013) N2 - A methodology for assessment, seismic verification and strengthening of existing masonry buildings is presented in this paper. The verification is performed using a calculation model calibrated with the results from ambient vibration measurements. The calibrated model serves as an input for a deformation-based verification procedure based on the Capacity Spectrum Method (CSM). The bearing capacity of the building is calculated from experimental capacity curves of the individual walls idealized with bilinear elastic-perfectly plastic curves. The experimental capacity curves were obtained from in-plane cyclic loading tests on unreinforced and strengthened masonry walls with reinforced concrete jackets. The seismic action is compared with the load-bearing capacity of the building considering non-linear material behavior with its post-peak capacity. The application of the CSM to masonry buildings and the influence of a traditional strengthening method are demonstrated on the example of a public school building in Skopje, Macedonia. Y1 - 2013 SN - 978-3-902749-04-8 N1 - Vienna Congress on Recent Advances in Earthquake Engineering and Structural Dynamics, Vienna, Austria, Paper No. 523 13. D-A-CH Tagung ; Vienna, Austria, 29. - 30. August 2013 http://hdl.handle.net/20.500.12188/15830 (Error - Cannot Connect to Server) ER - TY - THES A1 - Donath, Paula T1 - Die Hebamme : Portrait eines der ältesten Berufe unserer Zeit N2 - Seit Jahrhunderten tragen Hebammen die Verantwortung für neues Leben und geben ihre Erfahrungen und ihr Können weiter. Trotz dieser ehrwürdigen Aufgabe gehören sie zu einer kleinen Berufsgruppe, die viel zu oft unterschätzt, überlastet und unterbezahlt wird. Sie sind Begleiter*innen in einer der sensibelsten und emotionalsten Zeiten des Lebens. Die Unterstützung einer Hebamme gewährleistet Aufklärung und Beistand während der Schwangerschaft, der Geburt und der Zeit im Wochenbett. Das Projekt »Die Hebamme« ist ein Berufsportrait. Die Arbeit gibt Einblicke in die Tätigkeit und seine verschiedenen Bereiche und erzählt dabei hauptsächlich in Bildern. Zusätzlich berichten Hebammen aus unterschiedlichen Blickwinkeln über ihre Arbeit. Dieses Portrait stellt die Realtität der Arbeit dar und soll die Bedeutung der Tätigkeit näher bringen. KW - Fotografie KW - Dokumentation KW - Dokumentarfotografie KW - Portrait KW - Hebamme Y1 - 2023 PB - FH Aachen CY - Aachen ER - TY - THES A1 - Alef, Sabrina T1 - Miela : digitale Wissensvermittlung für Vorschulkinder N2 - Kinder sind bei der Suche nach Antworten auf ihre Fragen in unserer medialen Gesellschaft stark mit dem digitalen Raum konfrontiert. Diese Medien können bei einer nicht kindergerechten Benutzung wichtige Entwicklungsprozesse hindern. Im Gegensatz dazu geben diese aber auch die Möglichkeit, Kindern wichtige Denkgewohnheiten beizubringen und sie besser auf die Zukunft vorzubereiten. Ziel der Arbeit ist es, eine Verbindung zwischen der analogen und digitalen Welt herzustellen und ein vielfältiges Lernen zu ermöglichen. Die App „miela“ schafft eine neue Ebene der Wissensvermittlung durch die Kombination von digitaler und analoger Welt. Das Userinterface ist altersentsprechend gestaltet und bietet unterschiedliche Themenfelder an, wobei die Wissensvermittlung und die Kreativität im Fokus stehen. Eine Zusammenarbeit mit der Toniebox als digitale Erweiterung kann weitere Themenfelder anbieten. KW - Digitales Lernen KW - Kinder KW - Analoge und Digitale Welt KW - Kreativität KW - Wissensvermittlung Y1 - 2023 PB - FH Aachen CY - Aachen ER - TY - JOUR A1 - Bialonski, Stephan A1 - Grieger, Niklas T1 - Der KI-Chatbot ChatGPT: Eine Herausforderung für die Hochschulen JF - Die neue Hochschule N2 - Essays, Gedichte, Programmcode: ChatGPT generiert automatisch Texte auf bisher unerreicht hohem Niveau. Dieses und nachfolgende Systeme werden nicht nur die akademische Welt nachhaltig verändern. Y1 - 2023 U6 - https://doi.org/10.5281/zenodo.7533758 SN - 0340-448X VL - 2023 IS - 1 SP - 24 EP - 27 PB - HLB CY - Bonn ER - TY - CHAP A1 - Pütz, Sebastian A1 - Baier, Ralph A1 - Brauner, Philipp A1 - Brillowski, Florian A1 - Dammers, Hannah A1 - Liehner, Luca A1 - Mertens, Alexander A1 - Rodemann, Niklas A1 - Schneider, Sebastian A1 - Schollemann, Alexander A1 - Steuer-Dankert, Linda A1 - Vervier, Luisa A1 - Gries, Thomas A1 - Leicht-Scholten, Carmen A1 - Nagel, Saskia K. A1 - Piller, Frank T. A1 - Schuh, Günther A1 - Ziefle, Martina A1 - Nitsch, Verena T1 - An interdisciplinary view on humane interfaces for digital shadows in the internet of production T2 - 2022 15th International Conference on Human System Interaction (HSI) N2 - Digital shadows play a central role for the next generation industrial internet, also known as Internet of Production (IoP). However, prior research has not considered systematically how human actors interact with digital shadows, shaping their potential for success. To address this research gap, we assembled an interdisciplinary team of authors from diverse areas of human-centered research to propose and discuss design and research recommendations for the implementation of industrial user interfaces for digital shadows, as they are currently conceptualized for the IoP. Based on the four use cases of decision support systems, knowledge sharing in global production networks, human-robot collaboration, and monitoring employee workload, we derive recommendations for interface design and enhancing workers’ capabilities. This analysis is extended by introducing requirements from the higher-level perspectives of governance and organization. KW - digital twin KW - digital shadow KW - cyber-physical production system KW - human-machine interface Y1 - 2022 SN - 978-1-6654-6823-7 (Print) SN - 978-1-6654-6822-0 (Online) U6 - https://doi.org/10.1109/HSI55341.2022.9869467 SN - 2158-2246 (Print) SN - 2158-2254 (Online) N1 - 15th International Conference on Human System Interaction (HSI), 28-31 July 2022, Melbourne, Australia. PB - IEEE ER - TY - CHAP A1 - Riga, Evi A1 - Pitilakis, Kyriazis A1 - Butenweg, Christoph A1 - Apostolaki, Stefania A1 - Karatzetzou, Anna ED - Arion, Cristian ED - Scupin, Alexandra ED - Ţigănescu, Alexandru T1 - Investigating the impact of the new European Seismic Hazard Model ESHM20 on the seismic design and safety control of industrial facilities T2 - The Third European Conference on Earthquake Engineering and Seismology N2 - The seismic performance and safety of major European industrial facilities has a global interest for Europe, its citizens and economy. A potential major disaster at an industrial site could affect several countries, probably far beyond the country where it is located. However, the seismic design and safety assessment of these facilities is practically based on national, often outdated seismic hazard assessment studies, due to many reasons, including the absence of a reliable, commonly developed seismic hazard model for whole Europe. This important gap is no more existing, as the 2020 European Seismic Hazard Model ESHM20 was released in December 2021. In this paper we investigate the expected impact of the adoption of ESHM20 on the seismic demand for industrial facilities, through the comparison of the ESHM20 probabilistic hazard at the sites where industrial facilities are located with the respective national and European regulations. The goal of this preliminary work in the framework of Working Group 13 of the European Association for Earthquake Engineering (EAEE), is to identify potential inadequacies in the design and safety control of existing industrial facilities and to highlight the expected impact of the adoption of the new European Seismic Hazard Model on the design of new industrial facilities and the safety assessment of existing ones. KW - ESHM20, industrial facilities KW - seismic hazard KW - seismic design KW - safety control Y1 - 2022 SN - 978-973-100-533-1 N1 - 3ECEES - Third European Conference on Earthquake Engineering and Seismology, September 4 – September 9, 2022, Bucharest SP - 3261 EP - 3270 ER - TY - CHAP A1 - Milijaš, Aleksa A1 - Šakić, Bogdan A1 - Marinković, Marko A1 - Butenweg, Christoph A1 - Gams, Matija A1 - Klinkel, Sven ED - Arion, Cristian ED - Scupin, Alexandra ED - Ţigănescu, Alexandru T1 - Effects of prior in-plane damage on out-of-plane response of masonry infills with openings T2 - The Third European Conference on Earthquake Engineering and Seismology N2 - Masonry infill walls are the most traditional enclosure system that is still widely used in RC frame buildings all over the world, particularly in seismic active regions. Although infill walls are usually neglected in seismic design, during an earthquake event they are subjected to in-plane and out-of-plane forces that can act separately or simultaneously. Since observations of damage to buildings after recent earthquakes showed detrimental effects of in-plane and out-of-plane load interaction on infill walls, the number of studies that focus on influence of in-plane damage on out-of-plane response has significantly increased. However, most of the xperimental campaigns have considered only solid infills and there is a lack of combined in-plane and out-of-plane experimental tests on masonry infills with openings, although windows and doors strongly affect seismic performance. In this paper, two types of experimental tests on infills with window openings are presented. The first is a pure out-of-plane test and the second one is a sequential in-plane and out-of-plane test aimed at investigating the effects of existing in-plane damage on outof-plane response. Additionally, findings from two tests with similar load procedure that were carried out on fully infilled RC frames in the scope of the same project are used for comparison. Test results clearly show that window opening increased vulnerability of infills to combined seismic actions and that prevention of damage in infills with openings is of the utmost importance for seismic safety. KW - Seismic loading KW - In-plane load KW - Out-of-plane load KW - Interaction KW - Window opening Y1 - 2022 SN - 978-973-100-533-1 N1 - 3ECEES - Third European Conference on Earthquake Engineering and Seismology, September 4 – September 9, 2022, Bucharest SP - 2747 EP - 2756 ER - TY - CHAP A1 - Morandi, Paolo A1 - Butenweg, Christoph A1 - Breis, Khaled A1 - Beyer, Katrin A1 - Magenes, Guido ED - Arion, Christian ED - Scupin, Alexandra ED - Ţigănescu, Alexandru T1 - Behaviour factor q for the seismic design of URM buildings T2 - The Third European Conference on Earthquake Engineering and Seismology N2 - Recent earthquakes showed that low-rise URM buildings following codecompliant seismic design and details behaved in general very well without substantial damages. Although advances in simulation tools make nonlinear calculation methods more readily accessible to designers, linear analyses will still be the standard design method for years to come. The present paper aims to improve the linear seismic design method by providing a proper definition of the q-factor of URM buildings. Values of q-factors are derived for low-rise URM buildings with rigid diaphragms, with reference to modern structural configurations realized in low to moderate seismic areas of Italy and Germany. The behaviour factor components for deformation and energy dissipation capacity and for overstrength due to the redistribution of forces are derived by means of pushover analyses. As a result of the investigations, rationally based values of the behaviour factor q to be used in linear analyses in the range of 2.0 to 3.0 are proposed. KW - unreinforced masonry buildings KW - modern constructions KW - seismic design KW - linear elastic analysis; KW - behaviour factor q Y1 - 2022 SN - 978-973-100-533-1 N1 - 3ECEES - Third European Conference on Earthquake Engineering and Seismology, September 4 – September 9, 2022, Bucharest SP - 1184 EP - 1194 ER - TY - CHAP A1 - Tomić, Igor A1 - Penna, Andrea A1 - DeJong, Matthew A1 - Butenweg, Christoph A1 - Correia, António A. A1 - Candeias, Paulo X. A1 - Senaldi, Ilaria A1 - Guerrini, Gabriele A1 - Malomo, Daniele A1 - Beyer, Katrin T1 - Seismic testing of adjacent interacting masonry structures T2 - 12th International Conference on Structural Analysis of Historical Constructions (SAHC 2020) N2 - In many historical centres in Europe, stone masonry buildings are part of building aggregates, which developed when the layout of the city or village was densified. In these aggregates, adjacent buildings share structural walls to support floors and roofs. Meanwhile, the masonry walls of the façades of adjacent buildings are often connected by dry joints since adjacent buildings were constructed at different times. Observations after for example the recent Central Italy earthquakes showed that the dry joints between the building units were often the first elements to be damaged. As a result, the joints opened up leading to pounding between the building units and a complicated interaction at floor and roof beam supports. The analysis of such building aggregates is very challenging and modelling guidelines do not exist. Advances in the development of analysis methods have been impeded by the lack of experimental data on the seismic response of such aggregates. The objective of the project AIMS (Seismic Testing of Adjacent Interacting Masonry Structures), included in the H2020 project SERA, is to provide such experimental data by testing an aggregate of two buildings under two horizontal components of dynamic excitation. The test unit is built at half-scale, with a two-storey building and a one-storey building. The buildings share one common wall while the façade walls are connected by dry joints. The floors are at different heights leading to a complex dynamic response of this smallest possible building aggregate. The shake table test is conducted at the LNEC seismic testing facility. The testing sequence comprises four levels of shaking: 25%, 50%, 75% and 100% of nominal shaking table capacity. Extensive instrumentation, including accelerometers, displacement transducers and optical measurement systems, provides detailed information on the building aggregate response. Special attention is paid to the interface opening, the globa KW - Historical centres KW - Stone masonry KW - Adjacent buildings KW - Shake table test Y1 - 2020 U6 - https://doi.org/10.23967/sahc.2021.234 N1 - 12th International Conference on Structural Analysis of Historical Constructions (SAHC 2021), September 29-30 and October 1, 2021, online N1 - (SAHC 2020 ursprünglich geplant für September 2020 in Barelona - verschoben wg. Covid-Pandemie) SP - 1 EP - 12 ER - TY - CHAP A1 - Tomic, Igor A1 - Penna, Andrea A1 - DeJong, Matthew A1 - Butenweg, Christoph A1 - Senaldi, Ilaria A1 - Guerrini, Gabriele A1 - Malomo, Daniele A1 - Beyer, Katrin T1 - Blind predictions of shake table testing of aggregate masonry buildings T2 - Proceedings of the 17th World Conference on Earthquake Engineering N2 - In many historical centers in Europe, stone masonry is part of building aggregates, which developed when the layout of the city or village was densified. The analysis of such building aggregates is very challenging and modelling guidelines missing. Advances in the development of analysis methods have been impeded by the lack of experimental data on the seismic response of such aggregates. The SERA project AIMS (Seismic Testing of Adjacent Interacting Masonry Structures) provides such experimental data by testing an aggregate of two buildings under two horizontal components of dynamic excitation. With the aim to advance the modelling of unreinforced masonry aggregates, a blind prediction competition is organized before the experimental campaign. Each group has been provided a complete set of construction drawings, material properties, testing sequence and the list of measurements to be reported. The applied modelling approaches span from equivalent frame models to Finite Element models using shell elements and discrete element models with solid elements. This paper compares the first entries, regarding the modelling approaches, results in terms of base shear, roof displacements, interface openings, and the failure modes. KW - Historical centres KW - Stone masonry KW - Adjacent buildings KW - Shake table test KW - Blind prediction competition Y1 - 2020 N1 - 17th World Conference on Earthquake Engineering, Sendai, Japan, September 27 to October 2, 2021 N1 - (Die Konferenz war ursprünglich für den 13-18 September 2020 angesetzt) ER - TY - CHAP A1 - Šakić, Bogdan A1 - Milijaš, Aleksa A1 - Marinković, Marko A1 - Butenweg, Christoph A1 - Klinkel, Sven ED - Papadrakakis, Manolis ED - Fragiadakis, Michalis T1 - Influence of prior in-plane damage on the out-of-plane response of non-load bearing unreinforced masonry walls under seismic load T2 - Proceedings of COMPDYN 2021 N2 - Reinforced concrete frames with masonry infill walls are popular form of construction all over the world as well in seismic regions. While severe earthquakes can cause high level of damage of both reinforced concrete and masonry infills, earthquakes of lower to medium intensity some-times can cause significant level of damage of masonry infill walls. Especially important is the level of damage of face loaded infill masonry walls (out-of-plane direction) as out-of-plane load cannot only bring high level of damage to the wall, it can also be life-threating for the people near the wall. The response in out-of-plane direction directly depends on the prior in-plane damage, as previous investigation shown that it decreases resistance capacity of the in-fills. Behaviour of infill masonry walls with and without prior in-plane load is investigated in the experimental campaign and the results are presented in this paper. These results are later compared with analytical approaches for the out-of-plane resistance from the literature. Conclusions based on the experimental campaign on the influence of prior in-plane damage on the out-of-plane response of infill walls are compared with the conclusions from other authors who investigated the same problematic. KW - Earthquake Engineering KW - Unreinforced masonry walls KW - Out-of-plane load KW - In- plane damage KW - Out-of-plane failure Y1 - 2021 SN - 9786188507258 U6 - https://doi.org/10.7712/120121.8527.18913 SN - 2623-3347 N1 - COMPDYN 2021, 28-30 June 2021, Streamed from Athens, Greece, 8th International Conference on Computational Methods in Structural Dynamics and Earthquake Engineering SP - 808 EP - 828 PB - National Technical University of Athens CY - Athen ER - TY - CHAP A1 - Milijaš, Aleksa A1 - Šakić, Bogdan A1 - Marinković, Marko A1 - Butenweg, Christoph ED - Papadrakakis, Manolis ED - Fragiadakis, Michalis T1 - Experimental investigation of behaviour of masonry infilled RC frames under out-of-plane loading T2 - Proceedings of COMPDYN 2021 N2 - Masonry infills are commonly used as exterior or interior walls in reinforced concrete (RC) frame structures and they can be encountered all over the world, including earthquake prone regions. Since the middle of the 20th century the behaviour of these non-structural elements under seismic loading has been studied in numerous experimental campaigns. However, most of the studies were carried out by means of in-plane tests, while there is a lack of out-of-plane experimental investigations. In this paper, the out-of-plane tests carried out on full scale masonry infilled frames are described. The results of the out-of-plane tests are presented in terms of force-displacement curves and measured out-of-plane displacements. Finally, the reliability of existing analytical approaches developed to estimate the out-of-plane strength of masonry infills is examined on presented experimental results. KW - Seismic loading KW - Masonry infill KW - Out-of-plane load KW - Out-of-plane strength Y1 - 2021 SN - 978-618-85072-5-8 U6 - https://doi.org/10.7712/120121.8528.18914 SN - 2623-3347 N1 - COMPDYN 2021, 28-30 June 2021, Streamed from Athens, Greece, 8th International Conference on Computational Methods in Structural Dynamics and Earthquake Engineering SP - 829 EP - 846 PB - National Technical University of Athens CY - Athen ER - TY - CHAP A1 - Butenweg, Christoph ED - Kuzmanović, Vladan ED - Ignjatović, Ivan T1 - Integrated approach for monitoring and management of buildings with digital building models and modern sensor technologies T2 - Proceedings of the International Conference Civil Engineering 2021 - Achievements and Visions N2 - Nowadays modern high-performance buildings and facilities are equipped with monitoring systems and sensors to control building characteristics like energy consumption, temperature pattern and structural safety. The visualization and interpretation of sensor data is typically based on simple spreadsheets and non-standardized user-oriented solutions, which makes it difficult for building owners, facility managers and decision-makers to evaluate and understand the data. The solution of this problem in the future are integrated BIM-Sensor approaches which allow the generation of BIM models incorporating all relevant information of monitoring systems. These approaches support both the dynamic visualization of key structural performance parameters, the effective long-term management of sensor data based on BIM and provide a user-friendly interface to communicate with various stakeholders. A major benefit for the end user is the use of the BIM software architecture, which is the future standard anyway. In the following, the application of the integrated BIM-Sensor approach is illustrated for a typical industrial facility as a part of an early warning and rapid response system for earthquake events currently developed in the research project “ROBUST” with financial support by the German Federal Ministry for Economic Affairs and Energy (BMWI). Y1 - 2021 N1 - Civil Engineering 2021 – Achievements and Visions, University of Belgrade, October 25 – 26, 2021 Belgrade, Serbia SP - 67 EP - 75 PB - University of Belgrade CY - Belgrade ER - TY - CHAP A1 - Milkova, Kristina A1 - Butenweg, Christoph A1 - Dumova-Jovanoska, Elena T1 - Region-sensitive comprehensive procedure for determination of seismic fragility curves T2 - 1st Croatian Conference on Earthquake Engineering 1CroCEE N2 - Seismic vulnerability estimation of existing structures is unquestionably interesting topic of high priority, particularly after earthquake events. Having in mind the vast number of old masonry buildings in North Macedonia serving as public institutions, it is evident that the structural assessment of these buildings is an issue of great importance. In this paper, a comprehensive methodology for the development of seismic fragility curves of existing masonry buildings is presented. A scenario – based method that incorporates the knowledge of the tectonic style of the considered region, the active fault characterization, the earth crust model and the historical seismicity (determined via the Neo Deterministic approach) is used for calculation of the necessary response spectra. The capacity of the investigated masonry buildings has been determined by using nonlinear static analysis. MINEA software (SDA Engineering) is used for verification of the structural safety of the structures Performance point, obtained from the intersection of the capacity of the building and the spectra used, is selected as a response parameter. The thresholds of the spectral displacement are obtained by splitting the capacity curve into five parts, utilizing empirical formulas which are represented as a function of yield displacement and ultimate displacement. As a result, four levels of damage limit states are determined. A maximum likelihood estimation procedure for the process of fragility curves determination is noted as a final step in the proposed procedure. As a result, region specific series of vulnerability curves for structures are defined. KW - seismic risk KW - seismic vulnerability KW - fragility curves KW - masonry structures Y1 - 2021 U6 - https://doi.org/10.5592/CO/1CroCEE.2021.158 N1 - 1st Croatian Conference on Earthquake Engineering 1CroCEE 2021, 22.–24. März 2021, University of Zagreb Faculty of Civil Engineering, Zagreb, Croatia SP - 121 EP - 128 PB - University of Zagreb CY - Zagreb ER - TY - CHAP A1 - Balaskas, Georgios A1 - Hoffmeister, Benno A1 - Butenweg, Christoph A1 - Pilz, Marco A1 - Bauer, Anna ED - Papadrakakis, Manolis ED - Fragiadakis, Michalis T1 - Earthquake early warning and response system based on intelligent seismic and monitoring sensors embedded in a communication platform and coupled with BIM models T2 - Proceedings of COMPDYN 2021 N2 - This paper describes the concept of an innovative, interdisciplinary, user-oriented earthquake warning and rapid response system coupled with a structural health monitoring system (SHM), capable to detect structural damages in real time. The novel system is based on interconnected decentralized seismic and structural health monitoring sensors. It is developed and will be exemplarily applied on critical infrastructures in Lower Rhine Region, in particular on a road bridge and within a chemical industrial facility. A communication network is responsible to exchange information between sensors and forward warnings and status reports about infrastructures’health condition to the concerned recipients (e.g., facility operators, local authorities). Safety measures such as emergency shutdowns are activated to mitigate structural damages and damage propagation. Local monitoring systems of the infrastructures are integrated in BIM models. The visualization of sensor data and the graphic representation of the detected damages provide spatial content to sensors data and serve as a useful and effective tool for the decision-making processes after an earthquake in the region under consideration. KW - early warning and response system KW - interconnected sensor systems KW - seismic structural damage detection via SHM KW - integration SHM in BIM Y1 - 2021 SN - 978-618-85072-5-8 U6 - https://doi.org/10.7712/120121.8539.18855 SN - 2623-3347 N1 - COMPDYN 2021, 28-30 June 2021, Streamed from Athens, Greece, 8th International Conference on Computational Methods in Structural Dynamics and Earthquake Engineering SP - 987 EP - 998 PB - National Technical University of Athens CY - Athen ER - TY - CHAP A1 - Butenweg, Christoph A1 - Bursi, Oreste S. A1 - Nardin, Chiara A1 - Lanese, Igor A1 - Pavese, Alberto A1 - Marinković, Marko A1 - Paolacci, Fabrizio A1 - Quinci, Gianluca T1 - Experimental investigation on the seismic performance of a multi-component system for major-hazard industrial facilities T2 - Conference Proceedings: Pressure Vessels & Piping Conference Vol.5 N2 - Past earthquakes demonstrated the high vulnerability of industrial facilities equipped with complex process technologies leading to serious damage of the process equipment and multiple and simultaneous release of hazardous substances in industrial facilities. Nevertheless, the design of industrial plants is inadequately described in recent codes and guidelines, as they do not consider the dynamic interaction between the structure and the installations and thus the effect of seismic response of the installations on the response of the structure and vice versa. The current code-based approach for the seismic design of industrial facilities is considered not enough for ensure proper safety conditions against exceptional event entailing loss of content and related consequences. Accordingly, SPIF project (Seismic Performance of Multi-Component Systems in Special Risk Industrial Facilities) was proposed within the framework of the European H2020 - SERA funding scheme (Seismology and Earthquake Engineering Research Infrastructure Alliance for Europe). The objective of the SPIF project is the investigation of the seismic behaviour of a representative industrial structure equipped with complex process technology by means of shaking table tests. The test structure is a three-story moment resisting steel frame with vertical and horizontal vessels and cabinets, arranged on the three levels and connected by pipes. The dynamic behaviour of the test structure and of its relative several installations is investigated. Furthermore, both process components and primary structure interactions are considered and analyzed. Several PGA-scaled artificial ground motions are applied to study the seismic response at different levels. After each test, dynamic identification measurements are carried out to characterize the system condition. The contribution presents the experimental setup of the investigated structure and installations, selected measurement data and describes the obtained damage. Furthermore, important findings for the definition of performance limits, the effectiveness of floor response spectra in industrial facilities will be presented and discussed. KW - industrial facilities KW - piping KW - installations KW - seismic loading KW - earthquakes Y1 - 2021 SN - 9780791885352 U6 - https://doi.org/10.1115/PVP2021-61696 N1 - ASME 2021 Pressure Vessels & Piping Conference, July 13–15, 2021, Virtual, Online PB - American Society of Mechanical Engineers (ASME) CY - New York ER - TY - CHAP A1 - Milkova, Kristina A1 - Butenweg, Christoph A1 - Dumova-Jovanoska, Elena T1 - Methodology for development of seismic vulnerability curve for existing unreinforced Masonry buildings T2 - Proceedings of the 17th World Conference on Earthquake Engineering N2 - Seismic behavior of an existing unreinforced masonry building built pre-modern code, located in the City of Ohrid, Republic of North Macedonia has been investigated in this paper. The analyzed school building is selected as an archetype in an ongoing project named “Seismic vulnerability assessment of existing masonry structures in Republic of North Macedonia (SeismoWall)”. Two independent segments were included in this research: Seismic hazard assessment by creating a cite specific response spectra and Seismic vulnerability definition by creating a region - specific series of vulnerability curves for the chosen building topology. A reliable Seismic Hazard Assessment for a selected region is a crucial point for performing a seismic risk analysis of a characteristic building class. In that manner, a scenario – based method that incorporates together the knowledge of tectonic style of the considered region, the active fault characterization, the earth crust model and the historical seismicity named Neo Deterministic approach is used for calculation of the response spectra for the location of the building. Variations of the rupturing process are taken into account in the nucleation point of the rupture, in the rupture velocity pattern and in the istribution of the slip on the fault. The results obtained from the multiple scenarios are obtained as an envelope of the response spectra computed for the cite using the procedure Maximum Credible Seismic Input (MCSI). Capacity of the selected building has been determined by using nonlinear static analysis. MINEA software (SDA Engineering) was used for verification of the structural safety of the chosen unreinforced masonry structure. In the process of optimization of the number of samples, computational cost required in a Monte Carlo simulation is significantly reduced since the simulation is performed on a polynomial response surface function for prediction of the structural response. Performance point, found as the intersection of the capacity of the building and the spectra used, is chosen as a response parameter. Five levels of damage limit states based on the capacity curve of the building are defined in dependency on the yield displacement and the maximum displacement. Maximum likelihood estimation procedure is utilized in the process of vulnerability curves determination. As a result, region specific series of vulnerability curves for the chosen type of masonry structures are defined. The obtained probabilities of exceedance a specific damage states as a result from vulnerability curves are compared with the observed damages happened after the earthquake in July 2017 in the City of Ohrid, North Macedonia. KW - Masonry structures KW - Vulnerability Curves KW - Capacity Curve KW - Neo-Deterministic KW - Seismic Hazard Y1 - 2020 N1 - 17th World Conference on Earthquake Engineering, Sendai, Japan, September 27 to October 2, 2021 N1 - (Die Konferenz war ursprünglich für den 13-18 September 2020 angesetzt) ER - TY - CHAP A1 - Marinković, Marko A1 - Butenweg, Christoph T1 - Out-of-plane behavior of decoupled masonry infills under seismic loading T2 - Proceedings of the 17th World Conference on Earthquake Engineering N2 - Masonry is used in many buildings not only for load-bearing walls, but also for non-load-bearing enclosure elements in the form of infill walls. Many studies confirmed that infill walls interact with the surrounding reinforced concrete frame, thus changing dynamic characteristics of the structure. Consequently, masonry infills cannot be neglected in the design process. However, although the relevant standards contain requirements for infill walls, they do not describe how these requirements are to be met concretely. This leads in practice to the fact that the infill walls are neither dimensioned nor constructed correctly. The evidence of this fact is confirmed by the recent earthquakes, which have led to enormous damages, sometimes followed by the total collapse of buildings and loss of human lives. Recently, the increasing effort has been dedicated to the approach of decoupling of masonry infills from the frame elements by introducing the gap in between. This helps in removing the interaction between infills and frame, but raises the question of out-of-plane stability of the panel. This paper presents the results of the experimental campaign showing the out-of-plane behavior of masonry infills decoupled with the system called INODIS (Innovative decoupled infill system), developed within the European project INSYSME (Innovative Systems for Earthquake Resistant Masonry Enclosures in Reinforced Concrete Buildings). Full scale specimens were subjected to the different loading conditions and combinations of in-plane and out-of-plane loading. Out-of-plane capacity of the masonry infills with the INODIS system is compared with traditionally constructed infills, showing that INODIS system provides reliable out-of-plane connection under various loading conditions. In contrast, traditional infills performed very poor in the case of combined and simultaneously applied in-plane and out-of-plane loading, experiencing brittle behavior under small in-plane drifts followed by high out-of-plane displacements. Decoupled infills with the INODIS system have remained stable under out-of-plane loads, even after reaching high in-plane drifts and being damaged. KW - in-plane KW - out-of-plane KW - INODIS KW - earthquake KW - connection detail Y1 - 2020 N1 - 17th World Conference on Earthquake Engineering, Sendai, Japan, September 27 to October 2, 2021 N1 - (Die Konferenz war ursprünglich für den 13-18 September 2020 angesetzt) ER - TY - CHAP A1 - Michel, Philipp A1 - Alder, Philipp A1 - Butenweg, Christoph A1 - Klinkel, Sven T1 - Berechnung der Fluid-Struktur-Interaktion für flexibel gelagerte Flüssigkeitstanks T2 - 16. D-A-CH Tagung Erdbebeningenieurwesen & Baudynamik: 26. und 27. September 2019, Universität Innsbruck Y1 - 2019 SN - 978-3-200-06454-6 ER - TY - CHAP A1 - Marinković, Marko A1 - Butenweg, Christoph ED - Papadrakakis, Manolis ED - Fragiadakis, Michalis T1 - Experimental and numerical analysis of RC frames with decoupled masonry infills T2 - 7th ECCOMAS Thematic Conference on Computational Methods in Structural Dynamics and Earthquake Engineering N2 - Masonry infill walls are commonly used in reinforced concrete (RC) frame structures, also in seismically active areas, although they often experience serious damage during earthquakes. One of the main reasons for their poor behaviour is the connection to the frame, which is usually constructed using mortar. This paper describes the novel solution for infill/frame connection based on application of elastomeric material between them. The system called INODIS (Innovative Decoupled Infill System) has the aim to postpone the activation of infill in in-plane direction and at the same time to provide sufficient out-of-plane support. First, experimental tests on infilled frame specimens are presented and the comparison of the results between traditionally infilled frames and infilled frames with the INODIS system are given. The results are then used for calibration and validation of numerical model, which can be further employed for investigating the influence of some material parameters on the behaviour of infilled frames with the INODIS system. KW - Earthquake KW - In-plane KW - Out-of-plane KW - Isolation KW - Seismic Y1 - 2019 SN - 978-618-82844-5-6 U6 - https://doi.org/10.7712/120119.7088.18845 SN - 2623-3347 N1 - COMPDYN 2019, 24-26 June 2019, Crete, Greece. SP - 2464 EP - 2479 PB - National Technical University of Athens CY - Athen ER - TY - JOUR A1 - Butenweg, Christoph A1 - Marinković, Marko A1 - Kubalski, Thomas A1 - Fehling, Ekkehard A1 - Pfetzing, Thomas A1 - Meyer, Udo ED - Voss, Michael T1 - Auslegung von Stahlbetonrahmentragwerken mit Ausfachungen aus Ziegelmauerwerk (Teil 2) T1 - Design of reinforced concrete enclosures infilled with clay block masonry (Part 2) JF - Ziegelindustrie international : ZI = Brick and tile industry international N2 - Im Rahmen des europäischen Verbundprojekts INSYSME wurden von den deutschen Partnern die Systeme IMES und INODIS zur Verbesserung des seismischen Verhaltens von ausgefachten Stahlbetonrahmen entwickelt. Ziel beider Systeme ist es, Stahlbetonrahmen und Ausfachung zu entkoppeln, anstatt die Tragfähigkeit durch aufwendige und kostspielige zusätzliche Bewehrungseinlagen zu erhöhen. Erste Ergebnisse des Systems IMES für Belastungen in und senkrecht zu der Wandebene werden vorgestellt. N2 - Within the scope of the joint European project INSYSME, the German partners developed two systems - IMES and INODIS - for improving the seismic behaviour of masonry infilled reinforced concrete frames. The purpose of both systems is to decouple frame and infill instead of working to improve their load-bearing capacity by means of elaborate, expensive, supplementary reinforcing elements. Initial findings for the IMES system with regard to the loads acting in-plane and perpendicular to the wall plane (out-of-plane) are presented. Y1 - 2018 SN - 0341-0552 IS - 6 SP - 24 EP - 43 PB - Bauverlag BV GmbH CY - Gütersloh ER - TY - JOUR A1 - Butenweg, Christoph A1 - Marinković, Marko A1 - Kubalski, Thomas A1 - Fehling, Ekkehard A1 - Pfetzing, Thomas A1 - Meyer, Udo ED - Voss, Michael T1 - Auslegung von Stahlbetonrahmentragwerken mit Ausfachungen aus Ziegelmauerwerk (Teil 1) T1 - Design of reinforced concrete enclosures infilled with clay block masonry (Part 1) JF - Ziegelindustrie international : ZI = Brick and tile industry international N2 - Im Rahmen des europäischen Verbundprojekts INSYSME wurden von den deutschen Partnern die Systeme IMES und INODIS zur Verbesserung des seismischen Verhaltens von ausgefachten Stahlbetonrahmen entwickelt. Ziel beider Systeme ist es, Stahlbetonrahmen und Ausfachung zu entkoppeln, anstatt die Tragfähigkeit durch aufwendige und kostspielige zusätzliche Bewehrungseinlagen zu erhöhen. Erste Ergebnisse des Systems IMES für Belastungen in und senkrecht zu der Wandebene werden vorgestellt. N2 - Within the scope of the joint European project INSYSME, the German partners developed two systems - IMES and INODIS - for improving the seismic behaviour of masonry infilled reinforced concrete frames. The purpose of both systems is to decouple frame and infill instead of working to improve their load-bearing capacity by means of elaborate, expensive, supplementary reinforcing elements. Initial findings for the IMES system with regard to the loads acting in-plane and perpendicular to the wall plane (out-of-plane) are presented. Y1 - 2018 SN - 0341-0552 IS - 4 SP - 30 EP - 39 PB - Bauverlag BV GmbH CY - Gütersloh ER - TY - GEN A1 - Topcu, Murat A1 - Madabhushi, Gopal Santana Phani A1 - Staat, Manfred T1 - Datasets from FEM Simulations done with COMSOL Multiphysics and Code_Aster N2 - Datasets from FEM Simulations done with COMSOL Multiphysics and Code_Aster for an elastic stress transfer between matrix and fibres having a variable radius. KW - Natural fibres KW - Polymer-matrix composites KW - Biocomposites KW - Stress concentrations KW - Finite element analysis (FEA) Y1 - 2022 U6 - https://doi.org/10.6084/m9.figshare.19333295.v2 ER - TY - JOUR A1 - Vahidpour, Farnoosh A1 - Guthman, Eric A1 - Arreola, Julia A1 - Alghazali, Yousef H. M. A1 - Wagner, Torsten A1 - Schöning, Michael Josef T1 - Assessment of Various Process Parameters for Optimized Sterilization Conditions Using a Multi-Sensing Platform JF - Foods N2 - In this study, an online multi-sensing platform was engineered to simultaneously evaluate various process parameters of food package sterilization using gaseous hydrogen peroxide (H₂O₂). The platform enabled the validation of critical aseptic parameters. In parallel, one series of microbiological count reduction tests was performed using highly resistant spores of B. atrophaeus DSM 675 to act as the reference method for sterility validation. By means of the multi-sensing platform together with microbiological tests, we examined sterilization process parameters to define the most effective conditions with regards to the highest spore kill rate necessary for aseptic packaging. As these parameters are mutually associated, a correlation between different factors was elaborated. The resulting correlation indicated the need for specific conditions regarding the applied H₂O₂ gas temperature, the gas flow and concentration, the relative humidity and the exposure time. Finally, the novel multi-sensing platform together with the mobile electronic readout setup allowed for the online and on-site monitoring of the sterilization process, selecting the best conditions for sterility and, at the same time, reducing the use of the time-consuming and costly microbiological tests that are currently used in the food package industry. KW - spore kill rate KW - sterility KW - aseptic parameters KW - multi-sensing platform KW - gaseous hydrogen peroxide Y1 - 2022 U6 - https://doi.org/10.3390/foods11050660 SN - 2304-8158 N1 - This article belongs to the Special Issue "Sensors and Biosensors Application for Food Industries" VL - 11 IS - 5 PB - MDPI CY - Basel ER - TY - CHAP A1 - Rajan, Sreelakshmy A1 - Kubalski, Thomas A1 - Altay, Okyay A1 - Dalguer, Luis A A1 - Butenweg, Christoph T1 - Multi-dimensional fragility analysis of a RC building with components using response surface method T2 - 24th International Conference on Structural Mechanics in Reactor Technology, Busan, Korea, 20-25 August, 2017 N2 - Conventional fragility curves describe the vulnerability of the main structure under external hazards. However, in complex structures such as nuclear power plants, the safety or the risk depends also on the components associated with a system. The classical fault tree analysis gives an overall view of the failure and contains several subsystems to the main event, however, the interactions in the subsystems are not well represented. In order to represent the interaction of the components, a method suggested by Cimellaro et al. (2006) using multidimensional performance limit state functions to obtain the system fragility curves is adopted. This approach gives the possibility of deriving the cumulative fragility taking into account the interaction of the response of different components. In this paper, this approach is used to evaluate seismic risk of a representative electrical building infrastructure, including the component, of a nuclear power plant. A simplified model of the structure, with nonlinear material behavior is employed for the analysis in Abaqus©. The input variables considered are the material parameters, boundary conditions and the seismic input. The variability of the seismic input is obtained from selected ground motion time histories of spectrum compatible synthetic ccelerograms. Unlike the usual Monte Carlo methods used for the probabilistic analysis of the structure, a computationally effective response surface method is used. This method reduces the computational effort of the calculations by reducing the required number of samples. Y1 - 2017 SN - 9781510856776 SP - 3126 EP - 3135 PB - International Assn for Structural Mechanics in Reactor Technology (IASMiRT) CY - Raleigh, USA ER - TY - JOUR A1 - Heuermann, Holger A1 - Harzheim, Thomas A1 - Cronenbroeck, Tobias T1 - First SIMO harmonic radar based on the SFCW concept and the HR transfer function JF - Remote sensing N2 - This paper presents a new SIMO radar system based on a harmonic radar (HR) stepped frequency continuous wave (SFCW) architecture. Simple tags that can be electronically individually activated and deactivated via a DC control voltage were developed and combined to form an MO array field. This HR operates in the entire 2.45 GHz ISM band for transmitting the illumination signal and receives at twice the stimulus frequency and bandwidth centered around 4.9 GHz. This paper presents the development, the basic theory of a HR system for the characterization of objects placed into the propagation path in-between the radar and the reflectors (similar to a free-space measurement with a network analyzer) as well as first measurements performed by the system. Further detailed measurement series will be made available later on to other researchers to develop AI and machine learning based signal processing routines or synthetic aperture radar algorithms for imaging, object recognition, and feature extraction. For this purpose, the necessary information is published in this paper. It is explained in detail why this SIMO-HR can be an attractive solution augmenting or replacing existing systems for radar measurements in production technology for material under test measurements and as a simplified MIMO system. The novel HR transfer function, which is a basis for researchers and developers for material characterization or imaging algorithms, is introduced and metrologically verified in a well traceable coaxial setup. KW - MUT measurement; scanner KW - transponder KW - SFCW KW - harmonic radar KW - nonlinear radar Y1 - 2021 U6 - https://doi.org/10.3390/rs13245088 SN - 2072-4292 N1 - This article belongs to the Special Issue "Nonlinear Junction Detection and Harmonic Radar" VL - 13 IS - 24 PB - MDPI CY - Basel ER - TY - JOUR A1 - Gorzalka, Philip A1 - Schmiedt, Jacob Estevam A1 - Schorn, Christian T1 - Automated Generation of an Energy Simulation Model for an Existing Building from UAV Imagery JF - Buildings N2 - An approach to automatically generate a dynamic energy simulation model in Modelica for a single existing building is presented. It aims at collecting data about the status quo in the preparation of energy retrofits with low effort and costs. The proposed method starts from a polygon model of the outer building envelope obtained from photogrammetrically generated point clouds. The open-source tools TEASER and AixLib are used for data enrichment and model generation. A case study was conducted on a single-family house. The resulting model can accurately reproduce the internal air temperatures during synthetical heating up and cooling down. Modelled and measured whole building heat transfer coefficients (HTC) agree within a 12% range. A sensitivity analysis emphasises the importance of accurate window characterisations and justifies the use of a very simplified interior geometry. Uncertainties arising from the use of archetype U-values are estimated by comparing different typologies, with best- and worst-case estimates showing differences in pre-retrofit heat demand of about ±20% to the average; however, as the assumptions made are permitted by some national standards, the method is already close to practical applicability and opens up a path to quickly estimate possible financial and energy savings after refurbishment. KW - Modelica KW - heat transfer coefficient KW - heat demand KW - building energy modelling KW - building energy simulation Y1 - 2021 U6 - https://doi.org/10.3390/buildings11090380 SN - 2075-5309 N1 - This article belongs to the Special Issue "Application of Computer Technology in Buildings" VL - 11 IS - 9 PB - MDPI CY - Basel ER - TY - JOUR A1 - Pourshahidi, Ali Mohammad A1 - Achtsnicht, Stefan A1 - Nambipareechee, Mrinal Murali A1 - Offenhäusser, Andreas A1 - Krause, Hans-Joachim T1 - Multiplex detection of magnetic beads using offset field dependent frequency mixing magnetic detection JF - Sensors N2 - Magnetic immunoassays employing Frequency Mixing Magnetic Detection (FMMD) have recently become increasingly popular for quantitative detection of various analytes. Simultaneous analysis of a sample for two or more targets is desirable in order to reduce the sample amount, save consumables, and save time. We show that different types of magnetic beads can be distinguished according to their frequency mixing response to a two-frequency magnetic excitation at different static magnetic offset fields. We recorded the offset field dependent FMMD response of two different particle types at frequencies ƒ₁ + n⋅ƒ₂, n = 1, 2, 3, 4 with ƒ₁ = 30.8 kHz and ƒ₂ = 63 Hz. Their signals were clearly distinguishable by the locations of the extremes and zeros of their responses. Binary mixtures of the two particle types were prepared with different mixing ratios. The mixture samples were analyzed by determining the best linear combination of the two pure constituents that best resembled the measured signals of the mixtures. Using a quadratic programming algorithm, the mixing ratios could be determined with an accuracy of greater than 14%. If each particle type is functionalized with a different antibody, multiplex detection of two different analytes becomes feasible. KW - colorization KW - multiplex detection KW - frequency mixing magnetic detection KW - magnetic nanoparticles Y1 - 2021 U6 - https://doi.org/10.3390/s21175859 SN - 1424-8220 N1 - This article belongs to the Special Issue "Advanced Nanomaterial-Based Sensors for Biomedical Applications" VL - 21 IS - 17 PB - MDPI CY - Basel ER - TY - JOUR A1 - Poghossian, Arshak A1 - Welden, Rene A1 - Buniatyan, Vahe V. A1 - Schöning, Michael Josef T1 - An Array of On-Chip Integrated, Individually Addressable Capacitive Field-Effect Sensors with Control Gate: Design and Modelling JF - Sensors N2 - The on-chip integration of multiple biochemical sensors based on field-effect electrolyte-insulator-semiconductor capacitors (EISCAP) is challenging due to technological difficulties in realization of electrically isolated EISCAPs on the same Si chip. In this work, we present a new simple design for an array of on-chip integrated, individually electrically addressable EISCAPs with an additional control gate (CG-EISCAP). The existence of the CG enables an addressable activation or deactivation of on-chip integrated individual CG-EISCAPs by simple electrical switching the CG of each sensor in various setups, and makes the new design capable for multianalyte detection without cross-talk effects between the sensors in the array. The new designed CG-EISCAP chip was modelled in so-called floating/short-circuited and floating/capacitively-coupled setups, and the corresponding electrical equivalent circuits were developed. In addition, the capacitance-voltage curves of the CG-EISCAP chip in different setups were simulated and compared with that of a single EISCAP sensor. Moreover, the sensitivity of the CG-EISCAP chip to surface potential changes induced by biochemical reactions was simulated and an impact of different parameters, such as gate voltage, insulator thickness and doping concentration in Si, on the sensitivity has been discussed. KW - equivalent circuit KW - multianalyte detection KW - control gate KW - on-chip integrated addressable EISCAP sensors KW - capacitive field-effect sensor Y1 - 2021 U6 - https://doi.org/10.3390/s21186161 SN - 1424-8220 N1 - This article belongs to the Special Issue "Field-Effect Sensors: From pH Sensing to Biosensing" VL - 21 IS - 18 SP - 17 PB - MDPI CY - Basel ER - TY - JOUR A1 - Akimbekov, Nuraly S. A1 - Digel, Ilya A1 - Tastambek, Kuanysh T. A1 - Sherelkhan, Dinara K. A1 - Jussupova, Dariya B. A1 - Altynbay, Nazym P. T1 - Low-rank coal as a source of humic substances for soil amendment and fertility management JF - Agriculture N2 - Humic substances (HS), as important environmental components, are essential to soil health and agricultural sustainability. The usage of low-rank coal (LRC) for energy generation has declined considerably due to the growing popularity of renewable energy sources and gas. However, their potential as soil amendment aimed to maintain soil quality and productivity deserves more recognition. LRC, a highly heterogeneous material in nature, contains large quantities of HS and may effectively help to restore the physicochemical, biological, and ecological functionality of soil. Multiple emerging studies support the view that LRC and its derivatives can positively impact the soil microclimate, nutrient status, and organic matter turnover. Moreover, the phytotoxic effects of some pollutants can be reduced by subsequent LRC application. Broad geographical availability, relatively low cost, and good technical applicability of LRC offer the advantage of easy fulfilling soil amendment and conditioner requirements worldwide. This review analyzes and emphasizes the potential of LRC and its numerous forms/combinations for soil amelioration and crop production. A great benefit would be a systematic investment strategy implicating safe utilization and long-term application of LRC for sustainable agricultural production. KW - soil remediation KW - crop yield KW - soil health KW - soil amendment KW - low-rank coal Y1 - 2021 U6 - https://doi.org/10.3390/agriculture11121261 SN - 2077-0472 N1 - This article belongs to the Special Issue "From Waste to Fertilizer in Sustainable Agriculture" VL - 11 IS - 12 PB - MDPI CY - Basel ER - TY - JOUR A1 - Fiedler, Thomas M. A1 - Orzada, Stephan A1 - Flöser, Martina A1 - Rietsch, Stefan H. G. A1 - Schmidt, Simon A1 - Stelter, Jonathan K. A1 - Wittrich, Marco A1 - Quick, Harald H. A1 - Bitz, Andreas A1 - Ladd, Mark E. T1 - Performance and safety assessment of an integrated transmit array for body imaging at 7 T under consideration of specificabsorption rate, tissue temperature, and thermal dose JF - NMR in Biomedicine N2 - In this study, the performance of an integrated body-imaging array for 7 T with 32 radiofrequency (RF) channels under consideration of local specific absorption rate (SAR), tissue temperature, and thermal dose limits was evaluated and the imaging performance was compared with a clinical 3 T body coil. Thirty-two transmit elements were placed in three rings between the bore liner and RF shield of the gradient coil. Slice-selective RF pulse optimizations for B1 shimming and spokes were performed for differently oriented slices in the body under consideration of realistic constraints for power and local SAR. To improve the B1+ homogeneity, safety assessments based on temperature and thermal dose were performed to possibly allow for higher input power for the pulse optimization than permissible with SAR limits. The results showed that using two spokes, the 7 T array outperformed the 3 T birdcage in all the considered regions of interest. However, a significantly higher SAR or lower duty cycle at 7 T is necessary in some cases to achieve similar B1+ homogeneity as at 3 T. The homogeneity in up to 50 cm-long coronal slices can particularly benefit from the high RF shim performance provided by the 32 RF channels. The thermal dose approach increases the allowable input power and the corresponding local SAR, in one example up to 100 W/kg, without limiting the exposure time necessary for an MR examination. In conclusion, the integrated antenna array at 7 T enables a clinical workflow for body imaging and comparable imaging performance to a conventional 3 T clinical body coil. KW - body imaging at 7 T MRI KW - thermal dose KW - tissue temperature KW - transmit antenna arrays Y1 - 2022 U6 - https://doi.org/10.1002/nbm.4656 SN - 0952-3480 (Print) SN - 1099-1492 (Online) VL - 35 IS - 5 SP - 1 EP - 17 PB - Wiley ER - TY - JOUR A1 - Angermann, Susanne A1 - Günthner, Roman A1 - Hanssen, Henner A1 - Lorenz, Georg A1 - Braunisch, Matthias C. A1 - Steubl, Dominik A1 - Matschkal, Julia A1 - Kemmner, Stephan A1 - Hausinger, Renate A1 - Block, Zenonas A1 - Haller, Bernhard A1 - Heemann, Uwe A1 - Kotliar, Konstantin A1 - Grimmer, Timo A1 - Schmaderer, Christoph T1 - Cognitive impairment and microvascular function in end-stage renal disease JF - International Journal of Methods in Psychiatric Research (MPR) N2 - Objective Hemodialysis patients show an approximately threefold higher prevalence of cognitive impairment compared to the age-matched general population. Impaired microcirculatory function is one of the assumed causes. Dynamic retinal vessel analysis is a quantitative method for measuring neurovascular coupling and microvascular endothelial function. We hypothesize that cognitive impairment is associated with altered microcirculation of retinal vessels. Methods 152 chronic hemodialysis patients underwent cognitive testing using the Montreal Cognitive Assessment. Retinal microcirculation was assessed by Dynamic Retinal Vessel Analysis, which carries out an examination recording retinal vessels' reaction to a flicker light stimulus under standardized conditions. Results In unadjusted as well as in adjusted linear regression analyses a significant association between the visuospatial executive function domain score of the Montreal Cognitive Assessment and the maximum arteriolar dilation as response of retinal arterioles to the flicker light stimulation was obtained. Conclusion This is the first study determining retinal microvascular function as surrogate for cerebral microvascular function and cognition in hemodialysis patients. The relationship between impairment in executive function and reduced arteriolar reaction to flicker light stimulation supports the involvement of cerebral small vessel disease as contributing factor for the development of cognitive impairment in this patient population and might be a target for noninvasive disease monitoring and therapeutic intervention. KW - cerebral small vessel disease KW - cognitive impairment KW - dialysis KW - retinal vessels Y1 - 2022 U6 - https://doi.org/10.1002/mpr.1909 SN - 1049-8931 (Print) SN - 1557-0657 (Online) VL - 31 IS - 2 SP - 1 EP - 10 PB - Wiley ER - TY - RPRT A1 - Ghinaiya, Jagdishkumar A1 - Lehmann, Thomas A1 - Göttsche, Joachim T1 - LOCAL+ – ein kreislauffähiger Holzmodulbau mit nachhaltigem Energie- und Wohnraumkonzept T2 - Bauphysik N2 - Mit dem Beitrag des Teams der FH Aachen zum SDE 21/22 wird im Projekt LOCAL+ ein kreislauffähiger Holzmodulbau mit einem innovativen Wohnraumkonzept geplant und umgesetzt. Ziel dieses Konzeptes ist die Verringerung des stetig steigenden Wohnflächenbedarfs durch ein Raum-in-Raum Konzept. Gebäudetechnisch wird in dem Projekt nicht nur das Einzelgebäude betrachtet, sondern unter Berücksichtigung des Gebäudebestandes wird für das Quartier ein innovatives und nachhaltiges Energiekonzept entwickelt. Ein zentrales Wasserstoffsystem ist für ein Quartier geplant, um den Stromverbrauch aus dem Netz im Winter zu reduzieren. Zentraler Bestandteil des TGA-Konzepts ist ein unterirdischer Eisspeicher, eine PVT und eine Wärmepumpe mit intelligenter Regelstrategie. Ein Teil des neuen Gebäudes (Design Challenge DC) wird in Wuppertal als Hausdemonstrationseinheit (HDU) präsentiert. Eine hygrothermische Simulation der HDU wurde mit der WUFI-Software durchgeführt. Da im Innenraum Lehmmodule und -platten als Feuchtigkeitspuffer verwendet werden, spielen die Themen Feuchtigkeit, Holzfäule und Schimmelwachstum eine wichtige Rolle. KW - Energiekonzept KW - Gesamtwassergehalt KW - Feuchtigkeit KW - Verdunstungskälte KW - energy concept Y1 - 2022 U6 - https://doi.org/10.1002/bapi.202200010 SN - 0171-5445 (Print) SN - 1437-0980 (Online) VL - 44 IS - 3 SP - 136 EP - 142 PB - Ernst & Sohn CY - Hoboken ER - TY - JOUR A1 - Karschuck, Tobias A1 - Kaulen, Corinna A1 - Poghossian, Arshak A1 - Wagner, Patrick H. A1 - Schöning, Michael Josef T1 - Gold nanoparticle-modified capacitive field-effect sensors: Studying the surface density of nanoparticles and coupling of charged polyelectrolyte macromolecules JF - Electrochemical Science Advances N2 - The coupling of ligand-stabilized gold nanoparticles with field-effect devices offers new possibilities for label-free biosensing. In this work, we study the immobilization of aminooctanethiol-stabilized gold nanoparticles (AuAOTs) on the silicon dioxide surface of a capacitive field-effect sensor. The terminal amino group of the AuAOT is well suited for the functionalization with biomolecules. The attachment of the positively-charged AuAOTs on a capacitive field-effect sensor was detected by direct electrical readout using capacitance-voltage and constant capacitance measurements. With a higher particle density on the sensor surface, the measured signal change was correspondingly more pronounced. The results demonstrate the ability of capacitive field-effect sensors for the non-destructive quantitative validation of nanoparticle immobilization. In addition, the electrostatic binding of the polyanion polystyrene sulfonate to the AuAOT-modified sensor surface was studied as a model system for the label-free detection of charged macromolecules. Most likely, this approach can be transferred to the label-free detection of other charged molecules such as enzymes or antibodies. KW - polystyrene sulfonate KW - gold nanoparticles KW - field-effect sensor KW - detection of charged macromolecules KW - capacitive EIS sensor Y1 - 2021 U6 - https://doi.org/10.1002/elsa.202100179 SN - 0938-5193 VL - 2 IS - 5 PB - Wiley-VCH CY - Weinheim ER - TY - JOUR A1 - Hoffmann, Andreas A1 - Rohrbach, Felix A1 - Uhl, Matthias A1 - Ceblin, Maximilian A1 - Bauer, Thomas A1 - Mallah, Marcel A1 - Jacob, Timo A1 - Heuermann, Holger A1 - Kuehne, Alexander J. C. T1 - Atmospheric pressure plasma-jet treatment of polyacrylonitrile-nonwovens—Stabilization and roll-to-roll processing JF - Journal of Applied Polymer Science N2 - Carbon nanofiber nonwovens represent a powerful class of materials with prospective application in filtration technology or as electrodes with high surface area in batteries, fuel cells, and supercapacitors. While new precursor-to-carbon conversion processes have been explored to overcome productivity restrictions for carbon fiber tows, alternatives for the two-step thermal conversion of polyacrylonitrile precursors into carbon fiber nonwovens are absent. In this work, we develop a continuous roll-to-roll stabilization process using an atmospheric pressure microwave plasma jet. We explore the influence of various plasma-jet parameters on the morphology of the nonwoven and compare the stabilized nonwoven to thermally stabilized samples using scanning electron microscopy, differential scanning calorimetry, and infrared spectroscopy. We show that stabilization with a non-equilibrium plasma-jet can be twice as productive as the conventional thermal stabilization in a convection furnace, while producing electrodes of comparable electrochemical performance. KW - batteries and fuel cells KW - electrospinning KW - fibers KW - irradiation KW - porous materials Y1 - 2022 U6 - https://doi.org/10.1002/app.52887 SN - 0021-8995 (Print) SN - 1097-4628 (Online) N1 - Weitere Informationen: Bundesministerium für Bildung und Forschung, Fördernummer: 13XP5036E. Deutsche Forschungsgemeinschaft, Fördernummern: 390874152, 441209207, 327886311 VL - 139 IS - 37 SP - 1 EP - 9 PB - Wiley ER - TY - CHAP A1 - Butenweg, Christoph A1 - Marinković, Marko A1 - Kubalski, Thomas A1 - Fehling, Ekkehard A1 - Pfetzing, Thomas A1 - Meyer, Udo ED - Zabel, Volkmar ED - Beinersdorf, Silke T1 - Innovative Ansätze für die seismische Auslegung von Stahlbetonrahmentragwerken mit Ausfachungen aus Ziegelmauerwerk T2 - Vortragsband der 15. D-A-CH-Tagung Erdbebeningenieurwesen und Baudynamik KW - Stahlbetonrahmen KW - Ausfachungsmauerwerk KW - INSYSME KW - Erdbeben KW - Ziegelmauerwerk Y1 - 2017 SN - 978-3-930108-13-5 SP - 130 EP - 145 PB - Deutsche Gesellschaft für Erdbebeningenieurwesen und Baudynamik (DGEB) e.V. CY - Weimar ER - TY - JOUR A1 - Pourshahidi, Ali Mohammad A1 - Achtsnicht, Stefan A1 - Offenhäusser, Andreas A1 - Krause, Hans-Joachim ED - Offenhäusser, Andreas T1 - Frequency Mixing Magnetic Detection Setup Employing Permanent Ring Magnets as a Static Offset Field Source JF - Sensors N2 - Frequency mixing magnetic detection (FMMD) has been explored for its applications in fields of magnetic biosensing, multiplex detection of magnetic nanoparticles (MNP) and the determination of core size distribution of MNP samples. Such applications rely on the application of a static offset magnetic field, which is generated traditionally with an electromagnet. Such a setup requires a current source, as well as passive or active cooling strategies, which directly sets a limitation based on the portability aspect that is desired for point of care (POC) monitoring applications. In this work, a measurement head is introduced that involves the utilization of two ring-shaped permanent magnets to generate a static offset magnetic field. A steel cylinder in the ring bores homogenizes the field. By variation of the distance between the ring magnets and of the thickness of the steel cylinder, the magnitude of the magnetic field at the sample position can be adjusted. Furthermore, the measurement setup is compared to the electromagnet offset module based on measured signals and temperature behavior. KW - magnetic sensors KW - biosensors KW - frequency mixing magnetic detection KW - magnetic nanoparticles Y1 - 2022 U6 - https://doi.org/10.3390/s22228776 SN - 1424-8220 VL - 22 IS - 22 PB - MDPI CY - Basel ER - TY - JOUR A1 - Poghossian, Arshak A1 - Karschuck, Tobias A1 - Wagner, Patrick A1 - Schöning, Michael Josef T1 - Field-Effect Capacitors Decorated with Ligand-Stabilized Gold Nanoparticles: Modeling and Experiments JF - Biosensors N2 - Nanoparticles are recognized as highly attractive tunable materials for designing field-effect biosensors with enhanced performance. In this work, we present a theoretical model for electrolyte-insulator-semiconductor capacitors (EISCAP) decorated with ligand-stabilized charged gold nanoparticles. The charged AuNPs are taken into account as additional, nanometer-sized local gates. The capacitance-voltage (C–V) curves and constant-capacitance (ConCap) signals of the AuNP-decorated EISCAPs have been simulated. The impact of the AuNP coverage on the shift of the C–V curves and the ConCap signals was also studied experimentally on Al–p-Si–SiO₂ EISCAPs decorated with positively charged aminooctanethiol-capped AuNPs. In addition, the surface of the EISCAPs, modified with AuNPs, was characterized by scanning electron microscopy for different immobilization times of the nanoparticles. KW - aminooctanethiol KW - nanoparticle coverage KW - capacitive model KW - gold nanoparticles KW - field-effect sensor KW - electrolyte-insulator-semiconductor capacitors Y1 - 2022 U6 - https://doi.org/10.3390/bios12050334 SN - 2079-6374 N1 - This article belongs to the Special Issue "Biosensors in Nanotechnology" VL - 12 IS - 5 PB - MDPI CY - Basel ER - TY - CHAP A1 - Boesen, Niklas A1 - Rosin, Julia A1 - Butenweg, Christoph A1 - Deichsel, Anne A1 - Klinkel, Sven ED - Zabel, Volkmar ED - Beinersdorf, Silke T1 - Untersuchung vorhandenerTragreserven moderner unbewehrter Mauerwerksbauten T2 - Vortragsband der 15. D-A-CH-Tagung Erdbebeningenieurwesen und Baudynamik Y1 - 2017 SN - 978-3-930108-13-5 N1 - 21.-22. September 2017, Weimar. ISBN laut DNB falsch SP - 408 EP - 418 PB - Deutsche Gesellschaft für Erdbebeningenieurwesen und Baudynamik (DGEB) e.V. CY - Weimar ER - TY - JOUR A1 - Vahidpour, Farnoosh A1 - Alghazali, Yousef A1 - Akca, Sevilay A1 - Hommes, Gregor A1 - Schöning, Michael Josef T1 - An Enzyme-Based Interdigitated Electrode-Type Biosensor for Detecting Low Concentrations of H₂O₂ Vapor/Aerosol JF - Chemosensors N2 - This work introduces a novel method for the detection of H₂O₂ vapor/aerosol of low concentrations, which is mainly applied in the sterilization of equipment in medical industry. Interdigitated electrode (IDE) structures have been fabricated by means of microfabrication techniques. A differential setup of IDEs was prepared, containing an active sensor element (active IDE) and a passive sensor element (passive IDE), where the former was immobilized with an enzymatic membrane of horseradish peroxidase that is selective towards H₂O₂. Changes in the IDEs’ capacitance values (active sensor element versus passive sensor element) under H₂O₂ vapor/aerosol atmosphere proved the detection in the concentration range up to 630 ppm with a fast response time (<60 s). The influence of relative humidity was also tested with regard to the sensor signal, showing no cross-sensitivity. The repeatability assessment of the IDE biosensors confirmed their stable capacitive signal in eight subsequent cycles of exposure to H₂O₂ vapor/aerosol. Room-temperature detection of H₂O₂ vapor/aerosol with such miniaturized biosensors will allow a future three-dimensional, flexible mapping of aseptic chambers and help to evaluate sterilization assurance in medical industry. Y1 - 2022 U6 - https://doi.org/10.3390/chemosensors10060202 SN - 2227-9040 N1 - This article belongs to the Special Issue "Bioinspired Chemical Sensors and Micro-Nano Devices" VL - 10 IS - 6 PB - MDPI CY - Basel ER - TY - JOUR A1 - Hoffmann, Andreas A1 - Uhl, Matthias A1 - Ceblin, Maximilian A1 - Rohrbach, Felix A1 - Bansmann, Joachim A1 - Mallah, Marcel A1 - Heuermann, Holger A1 - Jacob, Timo A1 - Kuehne, Alexander J.C. T1 - Atmospheric pressure plasma-jet treatment of PAN-nonwovens—carbonization of nanofiber electrodes JF - C - Journal of Carbon Research N2 - Carbon nanofibers are produced from dielectric polymer precursors such as polyacrylonitrile (PAN). Carbonized nanofiber nonwovens show high surface area and good electrical conductivity, rendering these fiber materials interesting for application as electrodes in batteries, fuel cells, and supercapacitors. However, thermal processing is slow and costly, which is why new processing techniques have been explored for carbon fiber tows. Alternatives for the conversion of PAN-precursors into carbon fiber nonwovens are scarce. Here, we utilize an atmospheric pressure plasma jet to conduct carbonization of stabilized PAN nanofiber nonwovens. We explore the influence of various processing parameters on the conductivity and degree of carbonization of the converted nanofiber material. The precursor fibers are converted by plasma-jet treatment to carbon fiber nonwovens within seconds, by which they develop a rough surface making subsequent surface activation processes obsolete. The resulting carbon nanofiber nonwovens are applied as supercapacitor electrodes and examined by cyclic voltammetry and impedance spectroscopy. Nonwovens that are carbonized within 60 s show capacitances of up to 5 F g⁻¹. Y1 - 2022 U6 - https://doi.org/10.3390/c8030033 SN - 2311-5629 N1 - This article belongs to the Collection "Nanoporous Carbon Materials for Advanced Technological Applications" VL - 8 IS - 3 PB - MDPI CY - Basel ER - TY - CHAP A1 - Butenweg, Christoph A1 - Meyer, Udo A1 - Fehling, Ekkehard T1 - INSYSME: first activities of the German partners T2 - 9th International Masonry Conference 2014 in Guimaraes, Portugal, 2014 Y1 - 2014 ER - TY - JOUR A1 - Akimbekov, Nuraly S. A1 - Digel, Ilya A1 - Tastambek, Kuanysh T. A1 - Marat, Adel K. A1 - Turaliyeva, Moldir A. A1 - Kaiyrmanova, Gulzhan K. T1 - Biotechnology of Microorganisms from Coal Environments: From Environmental Remediation to Energy Production JF - Biology N2 - It was generally believed that coal sources are not favorable as live-in habitats for microorganisms due to their recalcitrant chemical nature and negligible decomposition. However, accumulating evidence has revealed the presence of diverse microbial groups in coal environments and their significant metabolic role in coal biogeochemical dynamics and ecosystem functioning. The high oxygen content, organic fractions, and lignin-like structures of lower-rank coals may provide effective means for microbial attack, still representing a greatly unexplored frontier in microbiology. Coal degradation/conversion technology by native bacterial and fungal species has great potential in agricultural development, chemical industry production, and environmental rehabilitation. Furthermore, native microalgal species can offer a sustainable energy source and an excellent bioremediation strategy applicable to coal spill/seam waters. Additionally, the measures of the fate of the microbial community would serve as an indicator of restoration progress on post-coal-mining sites. This review puts forward a comprehensive vision of coal biodegradation and bioprocessing by microorganisms native to coal environments for determining their biotechnological potential and possible applications. Y1 - 2022 U6 - https://doi.org/10.3390/biology11091306 SN - 2079-7737 N1 - This article belongs to the Special Issue "Microbial Ecology and Evolution in Extreme Environments" VL - 11 IS - 9 PB - MDPI CY - Basel ER - TY - JOUR A1 - Schulte-Tigges, Joschua A1 - Förster, Marco A1 - Nikolovski, Gjorgji A1 - Reke, Michael A1 - Ferrein, Alexander A1 - Kaszner, Daniel A1 - Matheis, Dominik A1 - Walter, Thomas T1 - Benchmarking of various LiDAR sensors for use in self-driving vehicles in real-world environments JF - Sensors N2 - Abstract In this paper, we report on our benchmark results of the LiDAR sensors Livox Horizon, Robosense M1, Blickfeld Cube, Blickfeld Cube Range, Velodyne Velarray H800, and Innoviz Pro. The idea was to test the sensors in different typical scenarios that were defined with real-world use cases in mind, in order to find a sensor that meet the requirements of self-driving vehicles. For this, we defined static and dynamic benchmark scenarios. In the static scenarios, both LiDAR and the detection target do not move during the measurement. In dynamic scenarios, the LiDAR sensor was mounted on the vehicle which was driving toward the detection target. We tested all mentioned LiDAR sensors in both scenarios, show the results regarding the detection accuracy of the targets, and discuss their usefulness for deployment in self-driving cars. KW - Lidar KW - Benchmark KW - Self-driving Y1 - 2022 U6 - https://doi.org/10.3390/s22197146 SN - 1424-8220 N1 - This article belongs to the Special Issue "Sensor Fusion for Vehicles Navigation and Robotic Systems" VL - 22 IS - 19 PB - MDPI CY - Basel ER - TY - CHAP A1 - Butenweg, Christoph A1 - Rajan, Sreelakshmy T1 - Design and construction techniques of AAC masonry buildings in earthquakes regions T2 - 10 years Xella research in Building Materials : Symposium on the 4th and 5th of September, Potsdam 2014 Y1 - 2014 ER - TY - RPRT A1 - Kluge, Katharina A1 - Kirsch, Ansgar A1 - Budach, Christoph T1 - Digitale Lehre in der Geotechnik: Aktueller Stand und weitere Entwicklungen T2 - geotechntik N2 - Digitale Lehrmaterialien werden seit mehreren Jahren in den Hochschulen eingesetzt und eröffnen ganz neue Wege zur Vermittlung des Lehrstoffs. Die Erstellung dieser Lehrmaterialien kann allerdings je nach Art und Qualität sehr zeitintensiv sein und für Lehrende einen großen Mehraufwand bedeuten. Im Rahmen eines Kooperationsprojekts zur Erstellung von Lehrvideos für geotechnische Feld- und Laborversuche haben die Autoren dieses Beitrags allerdings die Erfahrung gemacht, dass das gemeinsame, hochschulübergreifende Erstellen von Lehrmaterialien viele Vorteile mit sich bringt. Dadurch inspiriert, führten die Autoren dieses Berichts eine Umfrage unter den deutschsprachigen Geotechnik-Lehrstühlen der (Technischen) Universitäten und (Fach-)Hochschulen durch. Nach drei Semestern, in denen Lehrveranstaltungen an den Hochschulen aufgrund der Corona-Pandemie überwiegend digital durchgeführt werden mussten, war es ein Ziel dieser Umfrage, den Bestand und den Einsatz digitaler Lehrmaterialien im Fachgebiet Geotechnik zu erheben. Ein weiteres Ziel war die Initiierung eines Netzwerks, in dem sich Geotechnik-Professorinnen und -Professoren zu Lehrthemen austauschen können und gemeinsam (digitale) Lehrmaterialien erstellen und nutzen. Der vorliegende Beitrag stellt das gemeinsame Lehrprojekt der Autoren vor, präsentiert die Ergebnisse der durchgeführten Umfrage und berichtet über die ersten Aktivitäten des neuen Netzwerks. KW - digitale Lehre KW - Geotechnik KW - digital teaching KW - geotechnical engineering KW - Didaktik Y1 - 2022 U6 - https://doi.org/10.1002/gete.202200013 SN - 0172-6145 (Print) SN - 2190-6653 (Online) IS - Early View PB - Ernst & Sohn CY - Berlin ER - TY - JOUR A1 - Haeger, Gerrit A1 - Grankin, Alina A1 - Wagner, Michaela T1 - Construction of an Aspergillus oryzae triple amylase deletion mutant as a chassis to evaluate industrially relevant amylases using multiplex CRISPR/Cas9 editing technology JF - Applied Research N2 - Aspergillus oryzae is an industrially relevant organism for the secretory production of heterologous enzymes, especially amylases. The activities of potential heterologous amylases, however, cannot be quantified directly from the supernatant due to the high background activity of native α-amylase. This activity is caused by the gene products of amyA, amyB, and amyC. In this study, an in vitro CRISPR/Cas9 system was established in A. oryzae to delete these genes simultaneously. First, pyrG of A. oryzae NSAR1 was mutated by exploiting NHEJ to generate a counter-selection marker. Next, all amylase genes were deleted simultaneously by co-transforming a repair template carrying pyrG of Aspergillus nidulans and flanking sequences of amylase gene loci. The rate of obtained triple knock-outs was 47%. We showed that triple knockouts do not retain any amylase activity in the supernatant. The established in vitro CRISPR/Cas9 system was used to achieve sequence-specific knock-in of target genes. The system was intended to incorporate a single copy of the gene of interest into the desired host for the development of screening methods. Therefore, an integration cassette for the heterologous Fpi amylase was designed to specifically target the amyB locus. The site-specific integration rate of the plasmid was 78%, with exceptional additional integrations. Integration frequency was assessed via qPCR and directly correlated with heterologous amylase activity. Hence, we could compare the efficiency between two different signal peptides. In summary, we present a strategy to exploit CRISPR/Cas9 for gene mutation, multiplex knock-out, and the targeted knock-in of an expression cassette in A. oryzae. Our system provides straightforward strain engineering and paves the way for development of fungal screening systems. KW - aspergillus KW - CRISPR/Cas9 KW - filamentous fungi KW - genome engineering Y1 - 2023 U6 - https://doi.org/10.1002/appl.202200106 SN - 2702-4288 IS - Early View SP - 1 EP - 15 PB - Wiley-VCH ER - TY - JOUR A1 - Rübbelke, Dirk A1 - Vögele, Stefan A1 - Grajewski, Matthias A1 - Zobel, Luzy T1 - Cross border adjustment mechanism: Initial data for the assessment of hydrogen-based steel production JF - Data in Brief N2 - Ambitious climate targets affect the competitiveness of industries in the international market. To prevent such industries from moving to other countries in the wake of increased climate protection efforts, cost adjustments may become necessary. Their design requires knowledge of country-specific production costs. Here, we present country-specific cost figures for different production routes of steel, paying particular attention to transportation costs. The data can be used in floor price models aiming to assess the competitiveness of different steel production routes in different countries (Rübbelke, 2022). KW - Energy-intensive industry KW - Steel industry KW - Competitiveness KW - Floor prices KW - Cross border adjustment mechanism Y1 - 2023 U6 - https://doi.org/10.1016/j.dib.2023.108907 SN - 2352-3409 VL - 47 IS - Article 108907 SP - 1 EP - 5 PB - Elsevier CY - Amsterdam ER - TY - JOUR A1 - Penner, Crystal A1 - Usherovich, Samuel A1 - Niedermeier, Jana A1 - Bélanger-Champagne, Camille A1 - Trinczek, Michael A1 - Paulßen, Elisabeth A1 - Hoehr, Cornelia T1 - Organic Scintillator-Fibre Sensors for Proton Therapy Dosimetry: SCSF-3HF and EJ-260 JF - electronics N2 - In proton therapy, the dose from secondary neutrons to the patient can contribute to side effects and the creation of secondary cancer. A simple and fast detection system to distinguish between dose from protons and neutrons both in pretreatment verification as well as potentially in vivo monitoring is needed to minimize dose from secondary neutrons. Two 3 mm long, 1 mm diameter organic scintillators were tested for candidacy to be used in a proton–neutron discrimination detector. The SCSF-3HF (1500) scintillating fibre (Kuraray Co. Chiyoda-ku, Tokyo, Japan) and EJ-260 plastic scintillator (Eljen Technology, Sweetwater, TX, USA) were irradiated at the TRIUMF Neutron Facility and the Proton Therapy Research Centre. In the proton beam, we compared the raw Bragg peak and spread-out Bragg peak response to the industry standard Markus chamber detector. Both scintillator sensors exhibited quenching at high LET in the Bragg peak, presenting a peak-to-entrance ratio of 2.59 for the EJ-260 and 2.63 for the SCSF-3HF fibre, compared to 3.70 for the Markus chamber. The SCSF-3HF sensor demonstrated 1.3 times the sensitivity to protons and 3 times the sensitivity to neutrons as compared to the EJ-260 sensor. Combined with our equations relating neutron and proton contributions to dose during proton irradiations, and the application of Birks’ quenching correction, these fibres provide valid candidates for inexpensive and replicable proton-neutron discrimination detectors Y1 - 2022 U6 - https://doi.org/10.3390/electronics12010011 SN - 2079-9292 N1 - This article belongs to the Special Issue "Applications of Optical Fiber Sensors" VL - 12 IS - 1 PB - MDPI CY - Basel ER - TY - JOUR A1 - Niedermeier, Jana A1 - Penner, Crystal A1 - Usherovich, Samuel A1 - Bélanger-Champagne, Camille A1 - Paulßen, Elisabeth A1 - Hoehr, Cornelia T1 - Optical Fibers as Dosimeter Detectors for Mixed Proton/Neutron Fields - A Biological Dosimeter JF - electronics N2 - In recent years, proton therapy has gained importance as a cancer treatment modality due to its conformality with the tumor and the sparing of healthy tissue. However, in the interaction of the protons with the beam line elements and patient tissues, potentially harmful secondary neutrons are always generated. To ensure that this neutron dose is as low as possible, treatment plans could be created to also account for and minimize the neutron dose. To monitor such a treatment plan, a compact, easy to use, and inexpensive dosimeter must be developed that not only measures the physical dose, but which can also distinguish between proton and neutron contributions. To that end, plastic optical fibers with scintillation materials (Gd₂O₂S:Tb, Gd₂O₂S:Eu, and YVO₄:Eu) were irradiated with protons and neutrons. It was confirmed that sensors with different scintillation materials have different sensitivities to protons and neutrons. A combination of these three scintillators can be used to build a detector array to create a biological dosimeter. KW - biological dosimeter KW - Bragg peak KW - relative dosimetry KW - optical fibers KW - proton therapy KW - protons KW - neutrons Y1 - 2023 U6 - https://doi.org/10.3390/electronics12020324 SN - 2079-9292 N1 - This article belongs to the Special Issue "Applications of Optical Fiber Sensors" VL - 12 IS - 2 PB - MDPI CY - Basel ER - TY - CHAP A1 - Rosin, Julia A1 - Kubalski, Thomas A1 - Butenweg, Christoph ED - Klinkel, Sven ED - Butenweg, Christoph ED - Lin, Gao ED - Holtschoppen, Britta T1 - Seismic isolation of cylindrical liquid storage tanks T2 - Seismic design of industrial facilities N2 - Seismic excited liquid filled tanks are subjected to extreme loading due to hydrodynamic pressures, which can lead to nonlinear stability failure of the thinwalled cylindrical tanks, as it is known from past earthquakes. A significant reduction of the seismically induced loads can be obtained by the application of base isolation systems, which have to be designed carefully with respect to the modified hydrodynamic behaviour of the tank in interaction with the liquid. For this reason a highly sophisticated fluid-structure interaction model has to be applied for a realistic simulation of the overall dynamic system. In the following, such a model is presented and compared with the results of simplified mathematical models for rigidly supported tanks. Finally, it is examined to what extent a simple mechanical model can represent the behaviour of a base isolated tank in case of seismic excitation Y1 - 2013 SN - 978-3-658-02810-7 SN - 978-3-658-02809-1 SN - 978-3-658-14037-3 U6 - https://doi.org/10.1007/978-3-658-02810-7_36 N1 - International Conference on Seismic Design of Industrial Facilities, Aachen, Germany, 26.-27.09.2013. https://sedif-conference.jimdofree.com/ SP - 429 EP - 440 PB - Springer Vieweg CY - Wiesbaden ER - TY - GEN A1 - Butenweg, Christoph A1 - Gellert, Christoph A1 - Reindl, Lukas A1 - Meskouris, Konstantin T1 - A nonlinear method for the seismic safety verification of masonry buildings N2 - In order for traditional masonry to stay a competitive building material in seismically active regions there is an urgent demand for modern, deformation-based verification procedures which exploit the nonlinear load bearing reserves. The Capacity Spectrum Method (CSM) is a widely accepted design approach in the field of reinforced concrete and steel construction. It compares the seismic action with the load-bearing capacity of the building considering nonlinear material behavior with its post-peak capacity. The bearing capacity of the building is calculated iteratively using single wall capacity curves. This paper presents a new approach for the bilinear approximation of single wall capacity curves in the style of EC6/EC8 respectively FEMA 306/FEMA 356 based on recent shear wall test results of the European Collective-Research Project “ESECMaSE”. The application of the CSM to masonry structures by using bilinear approximations of capacity curves as input is demonstrated on the example of a typical German residential home. Y1 - 2009 N1 - COMPDYN 2009 - 2nd International Conference on Computational Methods in Structural Dynamics & Earthquake Engineering. Isles of Rhodes, Greece, June 22-24,2009. PB - National Technical University of Athens CY - Athen ER - TY - THES A1 - Ihl, Andrea T1 - Sehen und gesehen werden: Eine Darstellung (post-)migrantischer Perspektiven N2 - In einer Welt, definiert durch Grenzziehungen, ist es vor allem für diejenigen schwer, ihren Platz zu finden, die bereits über diese hinauswachsen mussten. Denn Migration bedeutet nicht nur, eine Strecke über eine ländliche Linie hinter sich zu bringen. Oft werden die komplexen emotionalen Facetten dieser permanenten Überquerung vergessen, die über Generationen ihre Spuren hinterlassen. Was bedeutet es, ein Leben ganz von neu aufbauen zu müssen, wenn man bereits eins hinter sich gelassen hat? Wieso verspüren wir Sehnsucht nach einer Heimat, die es so gar nicht geben kann? Und wann haben wir das Gefühl, endlich angekommen zu sein? Über diese und viele weitere Fragen wird in »Mesta« zusammen mit (Post-)Migrant:innen reflektiert, die intensiv ihre Erfahrungen teilen. Ziel der Publikation ist das, was meistens vernachlässigt wird: einfach zuzuhören. KW - Illustration KW - Editorialdesign KW - Interview KW - Print KW - Postmigrantisch Y1 - 2022 PB - FH Aachen CY - Aachen ER - TY - JOUR A1 - Šakić, Bogdan A1 - Marinković, Marko A1 - Butenweg, Christoph A1 - Klinkel, Sven ED - Yang, J. T1 - Influence of slab deflection on the out-of-plane capacity of unreinforced masonry partition walls JF - Engineering Structures N2 - Severe damage of non-structural elements is noticed in previous earthquakes, causing high economic losses and posing a life threat for the people. Masonry partition walls are one of the most commonly used non-structural elements. Therefore, their behaviour under earthquake loading in out-of-plane (OOP) direction is investigated by several researches in the past years. However, none of the existing experimental campaigns or analytical approaches consider the influence of prior slab deflection on OOP response of partition walls. Moreover, none of the existing construction techniques for the connection of partition walls with surrounding reinforced concrete (RC) is investigated for the combined slab deflection and OOP loading. However, the inevitable time-dependent behaviour of RC slabs leads to high values of final slab deflections which can further influence boundary conditions of partition walls. Therefore, a comprehensive study on the influence of slab deflection on the OOP capacity of masonry partitions is conducted. In the first step, experimental tests are carried out. Results of experimental tests are further used for the calibration of the numerical model employed for a parametric study. Based on the results, behaviour under combined loading for different construction techniques is explained. The results show that slab deflection leads either to severe damage or to a high reduction of OOP capacity. Existing practical solutions do not account for these effects. In this contribution, recommendations to overcome the problems of combined slab deflection and OOP loading on masonry partition walls are given. Possible interaction of in-plane (IP) loading, with the combined slab deflection and OOP loading on partition walls, is not investigated in this study. KW - Masonry partition walls KW - Earthquake KW - Out-of-plane capacity KW - Slab deflection Y1 - 2023 U6 - https://doi.org/10.1016/j.engstruct.2022.115342 SN - 0141-0296 VL - 276 PB - Elsevier CY - Amsterdam ER - TY - JOUR A1 - Kubalski, Thomas A1 - Butenweg, Christoph A1 - El-Deib, Khaled ED - Jesse, Dirk T1 - Vereinfachte Berücksichtigung der Rahmentragwirkung in Mauerwerksgebäuden T1 - Simplified consideratioon of framing effects in masonry buildings JF - Bautechnik N2 - Aufgrund der gestiegenen Anforderungen durch höhere Ein-wirkungen aus Wind und Erdbeben ist eine Verbesserung und Optimierung der Berechnungs- und Bemessungsansätze für Mauerwerksbauten erforderlich. Eine bessere Ausnutzung der Tragwerksreserven ist durch die Berücksichtigung der Rah-mentragwirkung mit einer Aktivierung der Deckenscheiben in den Rechenmodellen möglich, die in der Praxis aufgrund der Komplexität der Wand-Decken-Interaktion bislang nicht aus-genutzt wird. Im vorliegenden Aufsatz wird ein vereinfachter Ansatz auf Grundlage der mitwirkenden Plattenbreite von Schubwänden aus Mauerwerk vorgestellt, der die wesentli-chen Einfl ussfaktoren in parametrisierten Tabellen erfasst. Damit steht den Tragwerksplanern ein einfach anwendbares Werkzeug zur Verfügung, um die Rahmentragwirkung in der Mauerwerksbemessung anzusetzen. N2 - Due to the increased requirements resulting from higher wind and earthquake loads, it is necessary to improve and optimise the calculation and design approaches for masonry structures. An important contribution to a better utilisation of the structural load-bearing reserves is the consideration of the framing ef-fects through the activation of the fl oor slabs in the calculation models, which has not been utilised in practice so far due to the complexity of the wall-slab interaction. The paper presents a simplifi ed approach based on the contributory slab width, which captures the essential infl uencing factors in parameter-ised tables. This provides structural engineers with a simple tool to exploit the frame load-bearing effect in masonry design. KW - Rahmentragwirkung KW - Mauerwerksgebäude KW - Wand-Decken-Interaktion KW - Momentenverteilung KW - DIN EN 1996 Y1 - 2022 U6 - https://doi.org/10.1002/bate.202200081 SN - 0932-8351 SN - 1437-0999 VL - 99 IS - 12 SP - 865 EP - 928 PB - Ernst & Sohn CY - Berlin ER - TY - JOUR A1 - Butenweg, Christoph A1 - Marinkovic, Marko A1 - Phlipp, Michel A1 - Lins, Robin A1 - Renaut, Philipp ED - Haghsheno, Shervin T1 - Isolierung und BIM-basiertes Bauwerksmonitoring des neuen Gebäudekomplexes für das BioSense-Institut in Novi Sad, Serbien JF - Bauingenieur N2 - Im Norden von Serbien erfolgt in Novi Sad der Neubau eines modernen Forschungsgebäudes für das BioSense-Institut mit finanzieller Unterstützung durch die Eu-ropäische Union. Der Gebäudeteil mit Laboren wird zum Schutz und zur Sicherstellung des reibungslosen Betriebs der sensiblen und kapitalintensiven technischen Einbauten mit ei-ner Erdbebenisolierung mit integrierter Körperschallisolation versehen. Zusätzlich wird der entkoppelte Laborteil des For-schungsgebäudes mit einem BIM-basierten Bauwerksmonito-ring versehen, um Änderungen des Gebäudezustands jederzeit abfragen und beurteilen zu können. KW - BIM KW - Sensor KW - Monitoring KW - Bauwerksüberwachung KW - Basisisolierung Y1 - 2022 U6 - https://doi.org/10.37544/0005-6650-2022-06-28 SN - 1436-4867 SN - 0005-6650 N1 - D-A-CH-Teil VL - 97 IS - 6 SP - S3 EP - S5 PB - VDI Fachmedien CY - Düsseldorf ER - TY - JOUR A1 - Morandi, Paolo A1 - Butenweg, Christoph A1 - Breis, Khaled A1 - Beyer, Katrin A1 - Magenes, Guido ED - Ansal, Atilla T1 - Latest findings on the behaviour factor q for the seismic design of URM buildings JF - Bulletin of Earthquake Engineering N2 - Recent earthquakes as the 2012 Emilia earthquake sequence showed that recently built unreinforced masonry (URM) buildings behaved much better than expected and sustained, despite the maximum PGA values ranged between 0.20–0.30 g, either minor damage or structural damage that is deemed repairable. Especially low-rise residential and commercial masonry buildings with a code-conforming seismic design and detailing behaved in general very well without substantial damages. The low damage grades of modern masonry buildings that was observed during this earthquake series highlighted again that codified design procedures based on linear analysis can be rather conservative. Although advances in simulation tools make nonlinear calculation methods more readily accessible to designers, linear analyses will still be the standard design method for years to come. The present paper aims to improve the linear seismic design method by providing a proper definition of the q-factor of URM buildings. These q-factors are derived for low-rise URM buildings with rigid diaphragms which represent recent construction practise in low to moderate seismic areas of Italy and Germany. The behaviour factor components for deformation and energy dissipation capacity and for overstrength due to the redistribution of forces are derived by means of pushover analyses. Furthermore, considerations on the behaviour factor component due to other sources of overstrength in masonry buildings are presented. As a result of the investigations, rationally based values of the behaviour factor q to be used in linear analyses in the range of 2.0–3.0 are proposed. KW - Unreinforced masonry buildings KW - Modern constructions KW - Seismic design KW - Linear elastic analysis KW - Behaviour factor q Y1 - 2022 U6 - https://doi.org/10.1007/s10518-022-01419-7 SN - 1573-1456 SN - 1570-761X VL - 20 IS - 11 SP - 5797 EP - 5848 PB - Springer Nature CY - Cham ER - TY - THES A1 - Gehrig, Jana T1 - Gynaika - Ungleichbehandlung ist besser N2 - „Gynaika“ – ist griechisch und bedeutet Frau, Frausein. Das Frausein stellt besonders in der Medizin und der Forschung ein Problem dar. Ihre Gesundheit leidet unter der Gleichbehandlung in der Medizin, da die Beschwerden von Frauen zu häufig nicht beachtet werden und undiagnostiziert bleiben. Das medizinisch fundierte Magazin ""Gynaika"" soll über Erkrankungen bei Frauen aufklären, die Leser:innen zu einer Diagnose und guten Behandlung verhelfen. Beschreibung der Erkrankung, Erklärungen zum Ablauf im Körper und Behandlungsmöglichkeiten stehen neben neusten Studien und Erfahrungen von Betroffenen an erster Stelle. Die Informationen werden durch erklärende Einschübe sowie anschauliche Illustrationen und Grafiken begleitet. Ziel ist es, mehr Aufmerksamkeit auf die Notwendigkeit einer Ungleichbehandlung der Geschlechter in der Medizin zu ziehen. KW - Illustration KW - Editorial KW - Informationsvisualisierung KW - Magazin KW - Frauengesundheit Y1 - 2022 PB - FH Aachen CY - Aachen ER - TY - THES A1 - Heining, Theresa Marie T1 - Das Museum Küppersmühle : Entwicklung eines neuen Erscheinungsbildes und Orientierungssystems für das Museum N2 - Der Raum des Museums ist kein funktionaler Ort. Er dient den Besucher:innen als Inspiration, gefüllt mit Kunst, Poesie und Konzept. Das Museum Küppersmühle ist dabei eine klassische White Cube Gallery mit weitläufigen Räumen, viel Platz für die Kunst und einer hochwertigen Sammlung. Es befindet sich in einem umgebauten, alten Speichergebäude im Duisburger Innenhafen. Im Zuge der Masterarbeit wurden ein Erscheinungsbild und Orientierungssystem für das Museums entwickelt. Das Gestaltungssystem ist ein Spiel von Verbindungen, die mal gradlinig, teilweise geschwungen und manchmal verdreht sind. Der geschwungene Pfeil wird hierbei zum Visual des Umwegs, des Gedankensprungs und des Entdeckens. Es ist ein Informationskonzept entstanden, das dazu einlädt, über die geführten Wege hinauszublicken. Es leitet digital und mittels verschiedener Printmedien durch die Ausstellung für moderne Kunst. KW - Erscheinungsbild KW - Orientierungssystem KW - Museum KW - Leitsystem KW - Architektur Y1 - 2022 PB - FH Aachen CY - Aachen ER - TY - THES A1 - Frohn, Paul T1 - Intrinsische Raster N2 - Das Projekt »Intrinsische Raster« erforscht Raster für Webseiten, beginnend mit Untersuchungen aus dem Bereich Print bis hin zu intrinsischen Rastern im Web. Die Entwicklung des Rasters ist von dem Bereich Print geprägt. Heute ist das Medium digital und responsiv. Das Raster wird im CSS definiert und verändert sich intrinsisch in allen Formatgrößen. »Intrinsisch« beschreibt hier die neue Stufe von programmierbaren Rastern im Webdesign, welche Spalten und Module nach vordefinierten Parametern verändert. Variable Fonts verfügen über individuelle Parameter und werden in dem Projekt als Color Fonts in Raster integriert. Im Zentrum steht die Weiterentwicklung der Designprofession, um Raster für zukünftige Anwendungen vorzubereiten. KW - Raster KW - Rastersysteme KW - Webdesign KW - Designwissenschaften KW - Typografie Y1 - 2022 PB - FH Aachen CY - Aachen ER - TY - THES A1 - Freh, Katharine T1 - The Distance : ein dystpischer Kurzfilm N2 - "THE DISTANCE" ist ein fiktionaler, dystopischer Kurzfilm, welcher sich mit dem Leben in einem diktatorischen Polizeistaat auseinandersetzt. Jegliche Art von Aufstand oder negativer Äußerung dem Staat gegenüber ist untersagt und wird hoch bestraft. Ziel dieser Arbeit ist es, die Zuschauer:innen zum Denken und zum Hinterfragen gesellschaftlicher Strukturen anzuregen. Durch passende Kostüme, Locations und Set-Design entsteht eine düstere und unbehagliche Atmosphäre. Die passende Musik und das Sounddesign unterstützen diese Atmosphäre und geben den Zuschauer:innen einen guten Einblick in diese neue Welt. Zuletzt stellt sich die Frage, ob Dystopien überhaupt noch fiktional sind oder doch schon zu unserer Realität geworden sind. KW - Dystopie KW - Kurzfilm KW - Zukunft KW - Gesellschaftskritik Y1 - 2022 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER - TY - THES A1 - Franca, Erma T1 - Cai : eine Orientierungshilfe für Geflüchtete und Migrant*innen in Deutschland N2 - Migration und Integration sind weltweit zwei allseits aktuelle Themen. Umso wichtiger ist es, die Ankunft und Integration von Migrant:innen und Geflüchteten so anschaulich wie nur möglich zu gestalten. Die Zielsetzung der Arbeit „Cai – Your guide through Germany“ ist es eine digitale Anwendung in Form einer App zu konzipieren, die Geflüchtete und Migrant:innen in Deutschland während des Migrations- und Integrationsprozesses unterstützt. Dies gelingt durch das strukturierte und themenspezifische Herantragen von notwendigen Informationen, Organisation sowie Selbsthilfeangeboten an die unterschiedlichen Zielgruppen. Unter der Berücksichtigung des Migrationsgrundes und des Standortes wird eine Ausgangssituation geschaffen mit individuellen Bedürfnissen und Fragen, die es zu beantworten gilt. Während Nutzer:innen durch „Cai“ digital, selbstständig und schnell an Informationen gelangen, werden gleichzeitig Behörden und Anlaufstellen sowie ihre Leistungen und Schwerpunkte aufgeführt, die Betroffene bei weiteren Anliegen aufsuchen können, um Unterstützung zu erhalten. Im Rahmen dieser Bachelorarbeit fokussiert sich das Projekt auf die Migrationsgruppe der Geflüchteten sowie ihre Fragen, Herausforderungen und Bedürfnisse in Deutschland. KW - Migration KW - Integration KW - Flucht KW - Geflüchtete KW - Migrationsgruppe Y1 - 2022 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER - TY - THES A1 - Atlioglu, Dennis T1 - Live it up : eine digitale Plattform für die Live–Veranstaltungsbranche N2 - Mit der App »atmosphere« soll die Veranstaltungsbranche in die digitale Welt eingeführt werden. Insbesondere nach der COVID–19 Pandemie bedarf es einer Erneuerung in dem Sektor für Liveunterhaltung. Die Auswirkungen der Krise auf diesen Wirtschaftszweig waren enorm und auch das Publikum litt unter der Situation. Die Mission von »atmosphere« besteht darin, den Zugang zu Veranstaltungen, Konzerten, Stand–Up–Auftritten und Festivals zu vereinfachen. Hierbei werden die Bereiche der Planung und der Buchung komplett in dem Service der App abgedeckt und die digitale Teilnahme an einem Event ermöglicht. Dies bietet neue Möglichkeiten für die Zukunft und dient als Alternative für Krisen. Insgesamt soll der Service den Zugang vereinfachen, die aufwendigen Planungsschritte reduzieren und die Knackpunkte in der Nutzererfahrung digitalisieren. KW - Veranstaltung KW - Konzert KW - Auftritt KW - Stand–Up–Comedy KW - App Y1 - 2022 PB - FH Aachen CY - Aachen ER - TY - JOUR A1 - Timme, Michael T1 - Beweislast beim gutgläubigen Erwerb eines Kraftfahrzeugs ohne Erhalt der Zulassungsbescheinigung Teil II — Zugleich eine Besprechung von BGH, Urt. v. 23.9.2022 – V ZR 148/21, MDR 2022, 1542 JF - Monatsschrift für Deutsches Recht N2 - Im Handel mit Kraftfahrzeugen gehören Aspekte des gutgläubigen Erwerbs zu den beinahe alltäglichen Standardproblemen. Der BGH fügt in seiner Entscheidung v. 23.9.2022–VZR148/21, MDR 2022, 1541 diesem im Detail breit gefächerten Themenfeld einen weiteren Mosaikstein hinzu: Der Erwerber erhielt das verkaufte Kfz ohne Übergabe einer Zulassungsbescheinigung Teil II, behauptet aber, diese Bescheinigung sei dem vom ihm eingeschalteten Vermittler bei Erwerb (als Fälschung) vorgelegt worden. Tatsächlich befand sich das Original durchgängig beim wahren Eigentümer, der nunmehr Herausgabe des Fahrzeugs verlangt. Der BGH schützt in dieser Gestaltung im Ergebnis den Erwerber. Die Entscheidung ist in mehrfacher Hinsicht bemerkenswert. Y1 - 2022 U6 - https://doi.org/doi.org/10.9785/mdtr-2023-770102 SN - 0340-1812 VL - 77 IS - 1 SP - r5 EP - r7 PB - Verlag Dr. Otto Schmidt CY - Köln ER - TY - JOUR A1 - Marinković, Marko A1 - Butenweg, Christoph ED - Ford, Michael C. T1 - Experimental testing of decoupled masonry infills with steel anchors for out-of-plane support under combined in-plane and out-of-plane seismic loading JF - Construction and Building Materials N2 - Because of simple construction process, high energy efficiency, significant fire resistance and excellent sound isolation, masonry infilled reinforced concrete (RC) frame structures are very popular in most of the countries in the world, as well as in seismic active areas. However, many RC frame structures with masonry infills were seriously damaged during earthquake events, as the traditional infills are generally constructed with direct contact to the RC frame which brings undesirable infill/frame interaction. This interaction leads to the activation of the equivalent diagonal strut in the infill panel, due to the RC frame deformation, and combined with seismically induced loads perpendicular to the infill panel often causes total collapses of the masonry infills and heavy damages to the RC frames. This fact was the motivation for developing different approaches for improving the behaviour of masonry infills, where infill isolation (decoupling) from the frame has been more intensively studied in the last decade. In-plane isolation of the infill wall reduces infill activation, but causes the need for additional measures to restrain out-of-plane movements. This can be provided by installing steel anchors, as proposed by some researchers. Within the framework of European research project INSYSME (Innovative Systems for Earthquake Resistant Masonry Enclosures in Reinforced Concrete Buildings) the system based on a use of elastomers for in-plane decoupling and steel anchors for out-of-plane restrain was tested. This constructive solution was tested and deeply investigated during the experimental campaign where traditional and decoupled masonry infilled RC frames with anchors were subjected to separate and combined in-plane ‬and out-of-plane loading. Based on a detailed evaluation and comparison of the test results, the performance and effectiveness of the developed system are illustrated. KW - Masonry infill KW - Reinforced concrete frame KW - Earthquake KW - INSYSME KW - Decoupling Y1 - 2022 U6 - https://doi.org/10.1016/j.conbuildmat.2021.126041 SN - 1879-0526 SN - 0950-0618 VL - 318 IS - 1 PB - Elsevier CY - Amsterdam ER - TY - JOUR A1 - El-Deib, Khaled A1 - Butenweg, Christoph A1 - Klinkel, Sven ED - Jesse, Dirk T1 - Erdbebennachweis von Mauerwerksbauten mit realistischen Modellen und erhöhten Verhaltensbeiwerten JF - Mauerwerk N2 - Die Anwendung des linearen Nachweiskonzepts auf Mauerwerksbauten führt dazu, dass bereits heute Standsicherheitsnachweise für Gebäude mit üblichen Grundrissen in Gebieten mit moderaten Erdbebeneinwirkungen nicht mehr geführt werden können. Diese Problematik wird sich in Deutschland mit der Einführung kontinuierlicher probabilistischer Erdbebenkarten weiter verschärfen. Aufgrund der Erhöhung der seismischen Einwirkungen, die sich vielerorts ergibt, ist es erforderlich, die vorhandenen, bislang nicht berücksichtigten Tragfähigkeitsreserven in nachvollziehbaren Nachweiskonzepten in der Baupraxis verfügbar zu machen. Der vorliegende Beitrag stellt ein Konzept für die gebäudespezifische Ermittlung von erhöhten Verhaltensbeiwerten vor. Die Verhaltensbeiwerte setzen sich aus drei Anteilen zusammen, mit denen die Lastumverteilung im Grundriss, die Verformungsfähigkeit und Energiedissipation sowie die Überfestigkeiten berücksichtigt werden. Für die rechnerische Ermittlung dieser drei Anteile wird ein nichtlineares Nachweiskonzept auf Grundlage von Pushover-Analysen vorgeschlagen, in denen die Interaktionen von Wänden und Geschossdecken durch einen Einspanngrad beschrieben werden. Für die Bestimmung der Einspanngrade wird ein nichtlinearer Modellierungsansatz eingeführt, mit dem die Interaktion von Wänden und Decken abgebildet werden kann. Die Anwendung des Konzepts mit erhöhten gebäudespezifischen Verhaltensbeiwerten wird am Beispiel eines Mehrfamilienhauses aus Kalksandsteinen demonstriert. Die Ergebnisse der linearen Nachweise mit erhöhten Verhaltensbeiwerten für dieses Gebäude liegen deutlich näher an den Ergebnissen nichtlinearer Nachweise und somit bleiben übliche Grundrisse in Erdbebengebieten mit den traditionellen linearen Rechenansätzen nachweisbar. N2 - Seismic verification of masonry buildings based on realistic calculation models and increased behavior factorsWith the application of the traditional linear verification con­cept to masonry structures it is already no longer possible to carry out structural safety verifications even for buildings with standard ground plan configurations in areas with moderate seismicity. This problem will be exacerbated in Germany with the introduction of continuous probabilistic earthquake maps. Due to the increased seismic actions, it is necessary to make the existing load­bearing capacity reserves that have not yet been taken into account available in comprehensible verifica­tion concepts in construction practice. This article presents a concept for the building­specific determination of increased behavior factors. The behavior factors are composed of three components, which take into account the load redistribution in ground plans, the deformation capability and energy dissipation and all kinds of overstrength effects. For the calculation of these three components, a non­linear verification concept based on pushover analyses is applied, in which the interac­tions of walls and floor slabs are described by a level of re­straint. A non­linear modeling approach of the overall building is introduced for the determination of the restraint levels, with which the interaction of walls and floor slabs can be simulated. The results of the linear verifications with increased behavior factors for this building are significantly closer to the results of non­linear verifications and thus the standard ground plan con­figurations in areas with moderate seismicity can still be veri­fied with the traditional linear calculation approaches. KW - Mauerwerksbauten KW - Erdbebeneinwirkung KW - Bemessung KW - Verhaltensbeiwerte KW - Pushover­Analysen Y1 - 2021 U6 - https://doi.org/10.1002/dama.202110014 SN - 1437-1022 SN - 1432-3427 VL - 2021 IS - 3 SP - 110 EP - 119 PB - Wiley CY - Weinheim ER - TY - JOUR A1 - Rossi, Leonardo A1 - Winands, Mark H. M. A1 - Butenweg, Christoph ED - Zhang, Jessica T1 - Monte Carlo Tree Search as an intelligent search tool in structural design problems JF - Engineering with Computers : An International Journal for Simulation-Based Engineering N2 - Monte Carlo Tree Search (MCTS) is a search technique that in the last decade emerged as a major breakthrough for Artificial Intelligence applications regarding board- and video-games. In 2016, AlphaGo, an MCTS-based software agent, outperformed the human world champion of the board game Go. This game was for long considered almost infeasible for machines, due to its immense search space and the need for a long-term strategy. Since this historical success, MCTS is considered as an effective new approach for many other scientific and technical problems. Interestingly, civil structural engineering, as a discipline, offers many tasks whose solution may benefit from intelligent search and in particular from adopting MCTS as a search tool. In this work, we show how MCTS can be adapted to search for suitable solutions of a structural engineering design problem. The problem consists of choosing the load-bearing elements in a reference reinforced concrete structure, so to achieve a set of specific dynamic characteristics. In the paper, we report the results obtained by applying both a plain and a hybrid version of single-agent MCTS. The hybrid approach consists of an integration of both MCTS and classic Genetic Algorithm (GA), the latter also serving as a term of comparison for the results. The study’s outcomes may open new perspectives for the adoption of MCTS as a design tool for civil engineers. KW - Monte Carlo Tree Search KW - Structural design KW - Artificial intelligence KW - Civil engineering KW - Genetic algorithm Y1 - 2022 U6 - https://doi.org/10.1007/s00366-021-01338-2 SN - 1435-5663 SN - 0177-0667 VL - 38 IS - 4 SP - 3219 EP - 3236 PB - Springer Nature CY - Cham ER - TY - JOUR A1 - Butenweg, Christoph A1 - Kubalski, Thomas A1 - El-Deib, Khaled A1 - Gellert, Christoph ED - Jesse, Dirk T1 - Erdbebennachweis von Mauerwerksbauten nach DIN EN 1998-1/NA-2021 JF - Bautechnik : Zeitschrift für den gesamten Ingenieurbau N2 - Mauerwerksbauten in Deutschland sind mit Einführung des nationalen Anwendungsdokuments DIN EN 1998-1/NA auf Grundlage einer neuen probabilistischen Erdbebenkarte nachzuweisen. Für erfolgreiche Erdbebennachweise üblicher Grundrissformen von Mauerwerksbauten stehen in dem zukünftigen Anwendungsdokument neue rechnerische Nachweismöglichkeiten zur Verfügung, mit denen die Tragfähigkeitsreserven von Mauerwerksbauten in der Baupraxis mit einem überschaubaren Aufwand besser in Ansatz gebracht werden können. Das Standardrechenverfahren ist weiterhin der kraftbasierte Nachweis, der nun mit höheren Verhaltensbeiwerten im Vergleich zur DIN 4149 durchgeführt werden kann. Die höheren Verhaltensbeiwerte basieren auf der besseren Ausnutzung der gebäudespezifischen Verformungsfähigkeit und Energiedissipation sowie der Lastumverteilung der Schubkräfte im Grundriss mit Ansatz von Rahmentragwirkung durch Wand-Deckeninteraktionen. Alternativ dazu kann ein nichtlinearer Nachweis auf Grundlage von Pushover-Analysen zur Anwendung kommen. Vervollständigt werden die Regelungen für Mauerwerksbauten durch neue Regelungen für nichttragende Innenwände und Außenmauerschalen. Der vorliegende Beitrag stellt die Grundlagen und Hintergründe der neuen rechnerischen Nachweise in DIN EN 1998-1/NA vor und demonstriert deren Anwendung an einem Beispiel aus der Praxis. Y1 - 2021 U6 - https://doi.org/10.1002/bate.202100064 SN - 1437-0999 SN - 0005-6820, 0932-8351 VL - 98 IS - 11 SP - 852 EP - 863 PB - Ernst & Sohn CY - Berlin ER - TY - THES A1 - Gaigall, Daniel T1 - Vergleich von statistischen Tests im verbundenen und unabhängigen Stichprobenfall N2 - Es werden Effizienzbegriffe zum Vergleich von statistischen Tests basierend auf verschiedenen statistischen Experimenten eingeführt. Dabei handelt es sich um die schon aus dem Vergleich von statistischen Tests in je demselben Modell bekannten asymptotischen relativen Effizienzen wie die Hodges-Lehmann-Effizienz, die Bahadur-Effizienz und die Pitman-Effizienz sowie um Kriterien basierend auf Volumina von Konfidenzbereichen. Effizienzaussagen werden unter anderem für Likelihood-Quotienten-Tests und Waldsche Tests im Rahmen eines allgemeinen multivariaten parametrischen Modells erhalten. Statistische Tests zur Prüfung von Hypothesen über die relative Wirksamkeit zweier Experimente werden vorgeschlagen. Auf der Grundlage der erhaltenen Ergebnisse erfolgt ein Vergleich der Wirksamkeit von korrespondierenden Verfahren bei verbundener Stichprobenerhebung und unabhängiger Stichprobenerhebung. Die Rolle der Kovarianzmatrix bei verbundener Stichprobenerhebung wird insbesondere unter der Annahme, dass die zugrunde liegenden Verteilungen durch k-parametrische Exponentialfamilien modellierbar sind, herausgearbeitet. Verbindungen zu Effizienzbegriffen bei Punkt- und Konfidenzbereichsschätzverfahren werden aufgezeigt. Ausführlichere Untersuchungen betreffen die korrespondierenden Hotellingschen T²-Tests im multivariaten Normalverteilungsfall, die klassischen Homogenitatstests bei k × k-Kontingenztafeln und die Wilcoxon Tests in nichtparametrischen Lagealternativmodellen KW - Vergleich von Experimenten KW - Hypothesentests KW - Effizienz KW - testing hypotheses KW - efficiency Y1 - 2016 U6 - https://doi.org/10.15488/8678 N1 - Dissertation, Gottfried Wilhelm Leibniz Universität Hannover, 2016 PB - Gottfried Wilhelm Leibniz Universität Hannover CY - Hannover ER - TY - JOUR A1 - Butenweg, Christoph A1 - Bursi, Oreste S. A1 - Paolacci, Fabrizio A1 - Marinković, Marko A1 - Lanese, Igor A1 - Nardin, Chiara A1 - Quinci, Gianluca ED - Yang, J. T1 - Seismic performance of an industrial multi-storey frame structure with process equipment subjected to shake table testing JF - Engineering Structures N2 - Past earthquakes demonstrated the high vulnerability of industrial facilities equipped with complex process technologies leading to serious damage of process equipment and multiple and simultaneous release of hazardous substances. Nonetheless, current standards for seismic design of industrial facilities are considered inadequate to guarantee proper safety conditions against exceptional events entailing loss of containment and related consequences. On these premises, the SPIF project -Seismic Performance of Multi-Component Systems in Special Risk Industrial Facilities- was proposed within the framework of the European H2020 SERA funding scheme. In detail, the objective of the SPIF project is the investigation of the seismic behaviour of a representative industrial multi-storey frame structure equipped with complex process components by means of shaking table tests. Along this main vein and in a performance-based design perspective, the issues investigated in depth are the interaction between a primary moment resisting frame (MRF) steel structure and secondary process components that influence the performance of the whole system; and a proper check of floor spectra predictions. The evaluation of experimental data clearly shows a favourable performance of the MRF structure, some weaknesses of local details due to the interaction between floor crossbeams and process components and, finally, the overconservatism of current design standards w.r.t. floor spectra predictions. KW - Multi-storey KW - Frame structure KW - Earthquake KW - Tank KW - Piping Y1 - 2021 U6 - https://doi.org/10.1016/j.engstruct.2021.112681 SN - 0141-0296 VL - 243 IS - 15 PB - Elsevier CY - Amsterdam ER - TY - JOUR A1 - Baringhaus, Ludwig A1 - Gaigall, Daniel T1 - On Hotelling’s T² test in a special paired sample case JF - Communications in Statistics - Theory and Methods N2 - In a special paired sample case, Hotelling’s T² test based on the differences of the paired random vectors is the likelihood ratio test for testing the hypothesis that the paired random vectors have the same mean; with respect to a special group of affine linear transformations it is the uniformly most powerful invariant test for the general alternative of a difference in mean. We present an elementary straightforward proof of this result. The likelihood ratio test for testing the hypothesis that the covariance structure is of the assumed special form is derived and discussed. Applications to real data are given. KW - complete block symmetry KW - Hotelling’s T² test KW - likelihood ratio test KW - uniformly most powerful invariant test Y1 - 2017 U6 - https://doi.org/10.1080/03610926.2017.1408828 SN - 1532-415X VL - 48 IS - 2 SP - 257 EP - 267 PB - Taylor & Francis CY - London ER - TY - JOUR A1 - Baringhaus, Ludwig A1 - Gaigall, Daniel T1 - Hotelling’s T² tests in paired and independent survey samples: An efficiency comparison JF - Journal of Multivariate Analysis N2 - Hotelling’s T² tests in paired and independent survey samples are compared using the traditional asymptotic efficiency concepts of Hodges–Lehmann, Bahadur and Pitman, as well as through criteria based on the volumes of corresponding confidence regions. Conditions characterizing the superiority of a procedure are given in terms of population canonical correlation type coefficients. Statistical tests for checking these conditions are developed. Test statistics based on the eigenvalues of a symmetrized sample cross-covariance matrix are suggested, as well as test statistics based on sample canonical correlation type coefficients. Y1 - 2017 U6 - https://doi.org/10.1016/j.jmva.2016.11.004 SN - 0047-259X VL - 2017 IS - 154 SP - 177 EP - 198 PB - Elsevier CY - Amsterdam ER - TY - JOUR A1 - Baringhaus, Ludwig A1 - Gaigall, Daniel T1 - On an asymptotic relative efficiency concept based on expected volumes of confidence regions JF - Statistics - A Journal of Theoretical and Applied Statistic N2 - The paper deals with an asymptotic relative efficiency concept for confidence regions of multidimensional parameters that is based on the expected volumes of the confidence regions. Under standard conditions the asymptotic relative efficiencies of confidence regions are seen to be certain powers of the ratio of the limits of the expected volumes. These limits are explicitly derived for confidence regions associated with certain plugin estimators, likelihood ratio tests and Wald tests. Under regularity conditions, the asymptotic relative efficiency of each of these procedures with respect to each one of its competitors is equal to 1. The results are applied to multivariate normal distributions and multinomial distributions in a fairly general setting. KW - Volume of confidence regions KW - asymptotic relative efficiency KW - likelihood ratio test KW - multivariate normal distribution KW - multinomial distribution Y1 - 2019 U6 - https://doi.org/10.1080/02331888.2019.1683560 SN - 1029-4910 VL - 53 IS - 6 SP - 1396 EP - 1436 PB - Taylor & Francis CY - London ER - TY - JOUR A1 - Gaigall, Daniel T1 - On a new approach to the multi-sample goodness-of-fit problem JF - Communications in Statistics - Simulation and Computation N2 - Suppose we have k samples X₁,₁,…,X₁,ₙ₁,…,Xₖ,₁,…,Xₖ,ₙₖ with different sample sizes ₙ₁,…,ₙₖ and unknown underlying distribution functions F₁,…,Fₖ as observations plus k families of distribution functions {G₁(⋅,ϑ);ϑ∈Θ},…,{Gₖ(⋅,ϑ);ϑ∈Θ}, each indexed by elements ϑ from the same parameter set Θ, we consider the new goodness-of-fit problem whether or not (F₁,…,Fₖ) belongs to the parametric family {(G₁(⋅,ϑ),…,Gₖ(⋅,ϑ));ϑ∈Θ}. New test statistics are presented and a parametric bootstrap procedure for the approximation of the unknown null distributions is discussed. Under regularity assumptions, it is proved that the approximation works asymptotically, and the limiting distributions of the test statistics in the null hypothesis case are determined. Simulation studies investigate the quality of the new approach for small and moderate sample sizes. Applications to real-data sets illustrate how the idea can be used for verifying model assumptions. KW - Goodness-of-fit test KW - Multi-sample problem KW - Parametric bootstrap Y1 - 2019 U6 - https://doi.org/10.1080/03610918.2019.1618472 SN - 1532-4141 VL - 53 IS - 10 SP - 2971 EP - 2989 PB - Taylor & Francis CY - London ER - TY - JOUR A1 - Ditzhaus, Marc A1 - Gaigall, Daniel T1 - A consistent goodness-of-fit test for huge dimensional and functional data JF - Journal of Nonparametric Statistics N2 - A nonparametric goodness-of-fit test for random variables with values in a separable Hilbert space is investigated. To verify the null hypothesis that the data come from a specific distribution, an integral type test based on a Cramér-von-Mises statistic is suggested. The convergence in distribution of the test statistic under the null hypothesis is proved and the test's consistency is concluded. Moreover, properties under local alternatives are discussed. Applications are given for data of huge but finite dimension and for functional data in infinite dimensional spaces. A general approach enables the treatment of incomplete data. In simulation studies the test competes with alternative proposals. KW - Cramér-von-Mises statistic KW - separable Hilbert space KW - huge dimensional data KW - functional data Y1 - 2018 U6 - https://doi.org/10.1080/10485252.2018.1486402 SN - 1029-0311 VL - 30 IS - 4 SP - 834 EP - 859 PB - Taylor & Francis CY - Abingdon ER - TY - JOUR A1 - Baringhaus, Ludwig A1 - Gaigall, Daniel A1 - Thiele, Jan Philipp T1 - Statistical inference for L²-distances to uniformity JF - Computational Statistics N2 - The paper deals with the asymptotic behaviour of estimators, statistical tests and confidence intervals for L²-distances to uniformity based on the empirical distribution function, the integrated empirical distribution function and the integrated empirical survival function. Approximations of power functions, confidence intervals for the L²-distances and statistical neighbourhood-of-uniformity validation tests are obtained as main applications. The finite sample behaviour of the procedures is illustrated by a simulation study. KW - Integrated empirical distribution (survival) function KW - Goodness-of-fit tests for uniformity KW - Numerical inversion of Laplace transforms KW - Coverage probability KW - Equivalence test Y1 - 2018 U6 - https://doi.org/10.1007/s00180-018-0820-0 SN - 1613-9658 VL - 2018 IS - 33 SP - 1863 EP - 1896 PB - Springer CY - Berlin ER - TY - JOUR A1 - Baringhaus, Ludwig A1 - Gaigall, Daniel T1 - Efficiency comparison of the Wilcoxon tests in paired and independent survey samples JF - Metrika N2 - The efficiency concepts of Bahadur and Pitman are used to compare the Wilcoxon tests in paired and independent survey samples. A comparison through the length of corresponding confidence intervals is also done. Simple conditions characterizing the dominance of a procedure are derived. Statistical tests for checking these conditions are suggested and discussed. KW - Wilcoxon tests KW - Pitman efficiency KW - Bahadur efficiency KW - Length of confidence intervals KW - Kernel density estimator Y1 - 2018 U6 - https://doi.org/10.1007/s00184-018-0661-4 SN - 1435-926X VL - 2018 IS - 81 SP - 891 EP - 930 PB - Springer CY - Berlin ER - TY - JOUR A1 - Baringhaus, Ludwig A1 - Gaigall, Daniel T1 - On an independence test approach to the goodness-of-fit problem JF - Journal of Multivariate Analysis N2 - Let X₁,…,Xₙ be independent and identically distributed random variables with distribution F. Assuming that there are measurable functions f:R²→R and g:R²→R characterizing a family F of distributions on the Borel sets of R in the way that the random variables f(X₁,X₂),g(X₁,X₂) are independent, if and only if F∈F, we propose to treat the testing problem H:F∈F,K:F∉F by applying a consistent nonparametric independence test to the bivariate sample variables (f(Xᵢ,Xⱼ),g(Xᵢ,Xⱼ)),1⩽i,j⩽n,i≠j. A parametric bootstrap procedure needed to get critical values is shown to work. The consistency of the test is discussed. The power performance of the procedure is compared with that of the classical tests of Kolmogorov–Smirnov and Cramér–von Mises in the special cases where F is the family of gamma distributions or the family of inverse Gaussian distributions. KW - Goodness-of-fit test KW - Independence test KW - Parametric bootstrap KW - Vapnik–Čhervonenkis class KW - Gamma distribution Y1 - 2015 U6 - https://doi.org/10.1016/j.jmva.2015.05.013 SN - 0047-259X VL - 2015 IS - 140 SP - 193 EP - 208 PB - Elsevier CY - Amsterdam ER - TY - JOUR A1 - Gaigall, Daniel T1 - Test for Changes in the Modeled Solvency Capital Requirement of an Internal Risk Model JF - ASTIN Bulletin N2 - In the context of the Solvency II directive, the operation of an internal risk model is a possible way for risk assessment and for the determination of the solvency capital requirement of an insurance company in the European Union. A Monte Carlo procedure is customary to generate a model output. To be compliant with the directive, validation of the internal risk model is conducted on the basis of the model output. For this purpose, we suggest a new test for checking whether there is a significant change in the modeled solvency capital requirement. Asymptotic properties of the test statistic are investigated and a bootstrap approximation is justified. A simulation study investigates the performance of the test in the finite sample case and confirms the theoretical results. The internal risk model and the application of the test is illustrated in a simplified example. The method has more general usage for inference of a broad class of law-invariant and coherent risk measures on the basis of a paired sample. KW - Bootstrap KW - Empirical process KW - Functional Delta Method KW - Hadamard differentiability KW - Paired sample Y1 - 2021 U6 - https://doi.org/10.1017/asb.2021.20 SN - 1783-1350 VL - 51 IS - 3 SP - 813 EP - 837 PB - Cambridge Univ. Press CY - Cambridge ER - TY - JOUR A1 - Gaigall, Daniel T1 - Hoeffding-Blum-Kiefer-Rosenblatt independence test statistic on partly not identically distributed data JF - Communications in Statistics - Theory and Methods N2 - The established Hoeffding-Blum-Kiefer-Rosenblatt independence test statistic is investigated for partly not identically distributed data. Surprisingly, it turns out that the statistic has the well-known distribution-free limiting null distribution of the classical criterion under standard regularity conditions. An application is testing goodness-of-fit for the regression function in a non parametric random effects meta-regression model, where the consistency is obtained as well. Simulations investigate size and power of the approach for small and moderate sample sizes. A real data example based on clinical trials illustrates how the test can be used in applications. KW - Brownian Pillow KW - Hoeffding-Blum-Kiefer-Rosenblatt independence test KW - not identically distributed KW - random effects meta-regression model Y1 - 2020 U6 - https://doi.org/10.1080/03610926.2020.1805767 SN - 1532-415X VL - 51 IS - 12 SP - 4006 EP - 4028 PB - Taylor & Francis CY - London ER - TY - JOUR A1 - Gaigall, Daniel T1 - Testing marginal homogeneity of a continuous bivariate distribution with possibly incomplete paired data JF - Metrika N2 - We discuss the testing problem of homogeneity of the marginal distributions of a continuous bivariate distribution based on a paired sample with possibly missing components (missing completely at random). Applying the well-known two-sample Crámer–von-Mises distance to the remaining data, we determine the limiting null distribution of our test statistic in this situation. It is seen that a new resampling approach is appropriate for the approximation of the unknown null distribution. We prove that the resulting test asymptotically reaches the significance level and is consistent. Properties of the test under local alternatives are pointed out as well. Simulations investigate the quality of the approximation and the power of the new approach in the finite sample case. As an illustration we apply the test to real data sets. KW - Marginal homogeneity test KW - Crámer–von-Mises distance KW - Paired sample KW - Incomplete data KW - Resampling test Y1 - 2019 U6 - https://doi.org/10.1007/s00184-019-00742-5 SN - 1435-926X VL - 2020 IS - 83 SP - 437 EP - 465 PB - Springer ER - TY - JOUR A1 - Gaigall, Daniel T1 - Rothman–Woodroofe symmetry test statistic revisited JF - Computational Statistics & Data Analysis N2 - The Rothman–Woodroofe symmetry test statistic is revisited on the basis of independent but not necessarily identically distributed random variables. The distribution-freeness if the underlying distributions are all symmetric and continuous is obtained. The results are applied for testing symmetry in a meta-analysis random effects model. The consistency of the procedure is discussed in this situation as well. A comparison with an alternative proposal from the literature is conducted via simulations. Real data are analyzed to demonstrate how the new approach works in practice. Y1 - 2020 U6 - https://doi.org/10.1016/j.csda.2019.106837 SN - 0167-9473 VL - 2020 IS - 142 SP - Artikel 106837 PB - Elsevier CY - Amsterdam ER - TY - CHAP A1 - Gaigall, Daniel T1 - On Consistent Hypothesis Testing In General Hilbert Spaces T2 - Proceedings of the 4th International Conference on Statistics: Theory and Applications (ICSTA’22) N2 - Inference on the basis of high-dimensional and functional data are two topics which are discussed frequently in the current statistical literature. A possibility to include both topics in a single approach is working on a very general space for the underlying observations, such as a separable Hilbert space. We propose a general method for consistently hypothesis testing on the basis of random variables with values in separable Hilbert spaces. We avoid concerns with the curse of dimensionality due to a projection idea. We apply well-known test statistics from nonparametric inference to the projected data and integrate over all projections from a specific set and with respect to suitable probability measures. In contrast to classical methods, which are applicable for real-valued random variables or random vectors of dimensions lower than the sample size, the tests can be applied to random vectors of dimensions larger than the sample size or even to functional and high-dimensional data. In general, resampling procedures such as bootstrap or permutation are suitable to determine critical values. The idea can be extended to the case of incomplete observations. Moreover, we develop an efficient algorithm for implementing the method. Examples are given for testing goodness-of-fit in a one-sample situation in [1] or for testing marginal homogeneity on the basis of a paired sample in [2]. Here, the test statistics in use can be seen as generalizations of the well-known Cramérvon-Mises test statistics in the one-sample and two-samples case. The treatment of other testing problems is possible as well. By using the theory of U-statistics, for instance, asymptotic null distributions of the test statistics are obtained as the sample size tends to infinity. Standard continuity assumptions ensure the asymptotic exactness of the tests under the null hypothesis and that the tests detect any alternative in the limit. Simulation studies demonstrate size and power of the tests in the finite sample case, confirm the theoretical findings, and are used for the comparison with concurring procedures. A possible application of the general approach is inference for stock market returns, also in high data frequencies. In the field of empirical finance, statistical inference of stock market prices usually takes place on the basis of related log-returns as data. In the classical models for stock prices, i.e., the exponential Lévy model, Black-Scholes model, and Merton model, properties such as independence and stationarity of the increments ensure an independent and identically structure of the data. Specific trends during certain periods of the stock price processes can cause complications in this regard. In fact, our approach can compensate those effects by the treatment of the log-returns as random vectors or even as functional data. Y1 - 2022 U6 - https://doi.org/10.11159/icsta22.157 N1 - 4th International Conference on Statistics: Theory and Applications (ICSTA’22), Prague, Czech Republic – July 28- 30 SP - Paper No. 157 PB - Avestia Publishing CY - Orléans, Kanada ER - TY - JOUR A1 - Ditzhaus, Marc A1 - Gaigall, Daniel T1 - Testing marginal homogeneity in Hilbert spaces with applications to stock market returns JF - Test N2 - This paper considers a paired data framework and discusses the question of marginal homogeneity of bivariate high-dimensional or functional data. The related testing problem can be endowed into a more general setting for paired random variables taking values in a general Hilbert space. To address this problem, a Cramér–von-Mises type test statistic is applied and a bootstrap procedure is suggested to obtain critical values and finally a consistent test. The desired properties of a bootstrap test can be derived that are asymptotic exactness under the null hypothesis and consistency under alternatives. Simulations show the quality of the test in the finite sample case. A possible application is the comparison of two possibly dependent stock market returns based on functional data. The approach is demonstrated based on historical data for different stock market indices. Y1 - 2022 U6 - https://doi.org/10.1007/s11749-022-00802-5 SN - 1863-8260 VL - 2022 IS - 31 SP - 749 EP - 770 PB - Springer ER - TY - JOUR A1 - Gaigall, Daniel A1 - Gerstenberg, Julian A1 - Trinh, Thi Thu Ha T1 - Empirical process of concomitants for partly categorial data and applications in statistics JF - Bernoulli N2 - On the basis of independent and identically distributed bivariate random vectors, where the components are categorial and continuous variables, respectively, the related concomitants, also called induced order statistic, are considered. The main theoretical result is a functional central limit theorem for the empirical process of the concomitants in a triangular array setting. A natural application is hypothesis testing. An independence test and a two-sample test are investigated in detail. The fairly general setting enables limit results under local alternatives and bootstrap samples. For the comparison with existing tests from the literature simulation studies are conducted. The empirical results obtained confirm the theoretical findings. KW - bootstrap KW - Categorial variable KW - Concomitant KW - Empirical process KW - Independence test Y1 - 2022 U6 - https://doi.org/10.3150/21-BEJ1367 SN - 1573-9759 VL - 28 IS - 2 SP - 803 EP - 829 PB - International Statistical Institute CY - Den Haag, NL ER - TY - CHAP A1 - Staat, Manfred A1 - Tran, Ngoc Trinh T1 - Strain based brittle failure criteria for rocks T2 - Proceedings of (NACOME2022) The 11th National Conference on Mechanics, Vol. 1. Solid Mechanics, Rock Mechanics, Artificial Intelligence, Teaching and Training N2 - When confining pressure is low or absent, extensional fractures are typical, with fractures occurring on unloaded planes in rock. These “paradox” fractures can be explained by a phenomenological extension strain failure criterion. In the past, a simple empirical criterion for fracture initiation in brittle rock has been developed. But this criterion makes unrealistic strength predictions in biaxial compression and tension. A new extension strain criterion overcomes this limitation by adding a weighted principal shear component. The weight is chosen, such that the enriched extension strain criterion represents the same failure surface as the Mohr–Coulomb (MC) criterion. Thus, the MC criterion has been derived as an extension strain criterion predicting failure modes, which are unexpected in the understanding of the failure of cohesive-frictional materials. In progressive damage of rock, the most likely fracture direction is orthogonal to the maximum extension strain. The enriched extension strain criterion is proposed as a threshold surface for crack initiation CI and crack damage CD and as a failure surface at peak P. Examples show that the enriched extension strain criterion predicts much lower volumes of damaged rock mass compared to the simple extension strain criterion. KW - Extension fracture KW - Extension strain criterion KW - Mohr–Coulomb criterion KW - Evolution of damage Y1 - 2023 SN - 978-604-357-084-7 N1 - 11th National Conference on Mechanics (NACOME 2022), December 2-3, 2022, VNU University of Engineering and Technology, Hanoi, Vietnam SP - 500 EP - 509 PB - Nha xuat ban Khoa hoc tu nhien va Cong nghe (Verlag Naturwissenschaft und Technik) CY - Hanoi ER - TY - BOOK A1 - Drumm, Christian A1 - Scheuermann, Bernd A1 - Weidner, Stefan T1 - Einstieg in SAP S/4HANA® : Geschäftsprozesse, Anwendungen, Zusammenhänge – Erklärt am Beispielunternehmen Global Bike N2 - Dieser verständliche Einstieg in SAP S/4HANA führt Sie anhand des Beispielunternehmens Global Bike durch die zentralen Abläufe in Vertrieb, Einkauf, Rechnungswesen, Produktion und Lagerverwaltung. Sie werden mit den betriebswirtschaftlichen Grundlagen, den relevanten Organisationsstrukturen und Stammdaten sowie den Prozessen vertraut gemacht. Mithilfe von Praxisbeispielen und Fallstudien sind Sie schon bald SAP-S/4HANA-Profi – für mehr Erfolg in Studium und Beruf! Y1 - 2023 SN - 9783836281560 (Print) SN - 9783836281584 (E-Book) N1 - Unter der Signatur 21 QGT 220 in der Bibliothek Eupener Straße vorhanden. PB - Rheinwerk Verlag CY - Bonn ER - TY - PAT A1 - Hüning, Felix A1 - Backes, Andreas T1 - Wiegand-Modul N2 - Ein Wiegand-Modul (110;210;310) umfassend- eine Sensorspule (112;212;312),- einen ersten Wiegand-Draht (116a;216a;316a), der zumindest teilweise innerhalb der Sensorspule (112;212;312) angeordnet ist, und- einen zweiten Wiegand-Draht (116b;216b;316b), der zumindest teilweise innerhalb der Sensorspule (112;212;312) angeordnet ist und sich im Wesentlichen parallel zu dem ersten Wiegand-Draht (116a;216a;316a) erstreckt, ist bekannt.Um eine effiziente Ausnutzung der durch die Ummagnetisierung der Wiegand-Drähte (116a,116b;216a,216b;316a,316b) in die Sensorspule (112;212;312) induzierten elektrischen Energie zu ermöglichen, sind der erste Wiegand-Draht (116a;216a;316a) und der zweite Wiegand-Draht (116b;216b;316b) bezogen auf eine axiale Richtung der Sensorspule (112;212;312) versetzt zueinander angeordnet. Y1 - 2023 N1 - Patent DE102021115745B3 2022.07.21 ER - TY - CHAP A1 - Engelmann, Ulrich M. A1 - Baumann, Martin ED - Herbig, Nicola ED - Poppelreuter, Stefan T1 - Moderationsexpertise für QMBs – das Mindset T2 - Qualitätsmanagement im Gesundheitswesen N2 - Teamsitzungen, Arbeitsgruppentreffen, Kickoffs und Meetings – sie alle werden mit dem Ziel durchgeführt, innerhalb einer vorgegebenen Zeitspanne ein gemeinsames Arbeitsziel zu erreichen. Damit die Zielerreichung auch bei komplexeren Arbeitsaufträgen nicht vom Zufall abhängt, empfiehlt es sich, die Leitung des Ablaufs einem Moderator zu übertragen. In diesem Beitrag einer mehrteiligen Serie wird beschrieben, über welches Mindset der Moderator verfügen sollte, welche grundsätzlichen Methoden hilfreich sind und was bei der Onlinemoderation im Besonderen zu beachten ist. Y1 - 2022 SN - 978-3-8249-0714-4 SP - Kapitel 10814 PB - TÜV-Verlag CY - Köln ET - 59. Update ER - TY - JOUR A1 - Marinković, Marko A1 - Flores Calvinisti, Santiago A1 - Butenweg, Christoph T1 - Numerical analysis of reinforced concrete frame buildings with decoupled infill walls T1 - Numerička analiza armiranobe tonskih okvirnih zgrada sa izolovanom zidanom ispunom JF - Building Materials and Structures JF - Građevinski materijali i konstrukcije N2 - Reinforced concrete (RC) buildings with masonry infill walls are widely used in many countries all over the world. Although infills are considered as non-structural elements, they significantly change dynamic characteristics of RC frame structures during earthquake excitation. Recently, significant effort was spent on studying decoupled infills, which are isolated from the surrounding frame usually by adding a gap between frame and infill. In this case, the frame deformation does not activate infill wall, thus infills are not influencing the behaviour of the frame. This paper presents the results of the investigation of the behaviour of RC frame buildings with the INODIS system that decouples masonry infills from the surrounding frame. Effect of masonry infill decoupling was investigated first on the one-bay onestorey frame. This was used as a base for parametric study on the frames with more bays and storeys, as well as on the building level. Change of stiffness and dynamic characteristics was analysed as well as response under earthquake loading. Comparison with the bare frame and traditionally infilled frame was performed. The results show that behaviour of the decoupled infilled frames is similar to the bare frame, whereas behaviour of frames with traditional infills is significantly different and demands complex numerical models. This means that if adequate decoupling is applied, design of N2 - Armiranobetonske (AB) zgrade sa zidanom ispunom se izvode u mnogim zemljama širom sveta. Iako se zidana ispuna posmatra kao nekonstruktivni element, ona značajno utiče na promenu dinamičkih karakteristika AB ramovskih konstrukcija u toku zemljotresnog dejstva. Odskora, značajan napor je utrošen na istraživanje izolovanih ispuna, koje su odvojene od okolnog rama obično ostavljanjem prostora između rama i ispune. U ovom slučaju deformacija rama ne aktivira ispunu i na taj način ispuna ne utiče na ponašanje rama. Ovaj rad predstavlja rezultate istraživanja ponašanja AB ramovskih zgrada sa INODIS sistemom koji izoluje ispunu u odnosu na okolni ram. Uticaj izolovane ispune je prvo ispitan na jednospratnim i jednobrodnim ramovima. Ovo je iskorišćeno kao osnova za parametarsku analizu na višespratnim i višebrodnim ramovima, kao i na primeru zgrade. Promena krutosti i dinamičkih karakteristika je analizirano kao i odgovor pri zemljotresnom dejstvu. Izvršeno je poređenje sa praznom ramovskom konstrukcijom kao i ramovima ispunjenim ispunom na tradicionalni način. Rezultati pokazuju da je ponašanje ramova sa izolovanom ispunom slično ponašanju praznih ramova, dok je ponašanje ramova sa tradicionalnom ispunom daleko drugačije i zahteva kompleksne numeričke modele. Ovo znači da ukoliko se primeni adekvatna konstruktivna mera izolacije ispune, proračun ramovskim zgrada sa zidanom ispunom se može značajno pojednostaviti. KW - masonry infill KW - seismic KW - INODIS KW - in-plane behaviour KW - out-of-plane behaviour Y1 - 2020 U6 - https://doi.org/10.5937/GRMK2004013M SN - 2217-8139 N1 - Text serbisch, ab 2011 serbisch und englisch VL - 63 IS - 4 SP - 13 EP - 48 PB - Society for Materials and Structures Testing of Serbia CY - Belgrad ER - TY - CHAP A1 - Chircu, Alina A1 - Czarnecki, Christian A1 - Friedmann, Daniel A1 - Pomaskow, Johanna A1 - Sultanow, Eldar T1 - Towards a Digital Twin of Society T2 - Proceedings of the 56th Hawaii International Conference on System Sciences 2023 N2 - This paper describes the potential for developing a digital twin of society- a dynamic model that can be used to observe, analyze, and predict the evolution of various societal aspects. Such a digital twin can help governmental agencies and policy makers in interpreting trends, understanding challenges, and making decisions regarding investments or policies necessary to support societal development and ensure future prosperity. The paper reviews related work regarding the digital twin paradigm and its applications. The paper presents a motivating case study- an analysis of opportunities and challenges faced by the German federal employment agency, Bundesagentur f¨ur Arbeit (BA), proposes solutions using digital twins, and describes initial proofs of concept for such solutions. KW - Digital twin KW - Digital transformation KW - Prototype KW - Society KW - Stress testing Y1 - 2023 SN - 978-0-9981331-6-4 N1 - 56th Hawaii International Conference on System Sciences, HICSS 2023, Maui, Hawaii, USA, January 3-6, 2023 SP - 6748 EP - 6757 PB - University of Hawai'i CY - Honolulu ER - TY - CHAP A1 - Butenweg, Christoph ED - Vacareanu, Radu ED - Ionescu, Constantin T1 - Seismic design and evaluation of industrial facilities T2 - The Third European Conference on Earthquake Engineering and Seismology N2 - Industrial facilities must be thoroughly designed to withstand seismic actions as they exhibit an increased loss potential due to the possibly wideranging damage consequences and the valuable process engineering equipment. Past earthquakes showed the social and political consequences of seismic damage to industrial facilities and sensitized the population and politicians worldwide for the possible hazard emanating from industrial facilities. However, a holistic approach for the seismic design of industrial facilities can presently neither be found in national nor in international standards. The introduction of EN 1998-4 of the new generation of Eurocode 8 will improve the normative situation with specific seismic design rules for silos, tanks and pipelines and secondary process components. The article presents essential aspects of the seismic design of industrial facilities based on the new generation of Eurocode 8 using the example of tank structures and secondary process components. The interaction effects of the process components with the primary structure are illustrated by means of the experimental results of a shaking table test of a three story moment resisting steel frame with different process components. Finally, an integrated approach of digital plant models based on building information modelling (BIM) and structural health monitoring (SHM) is presented, which provides not only a reliable decision-making basis for operation, maintenance and repair but also an excellent tool for rapid assessment of seismic damage. KW - Industrial facilities KW - Seismic design KW - Tanks KW - EN 1998-4 KW - Structural health monitoring Y1 - 2022 SN - 978-3-031-15103-3 SN - 978-3-031-15106-4 SN - 978-3-031-15104-0 U6 - https://doi.org/10.1007/978-3-031-15104-0 SN - 2524-342X SN - 2524-3438 N1 - 3ECEES - Third European Conference on Earthquake Engineering and Seismology, September 4 – September 9, 2022, Bucharest SP - 449 EP - 464 PB - Springer CY - Cham ER - TY - CHAP A1 - Gkatzogias, Konstantinos A1 - Veljkoviv, Ana A1 - Pohoryles, Daniel A. A1 - Tsionis, Georgios A1 - Bournas, Dionysios A. A1 - Crowley, Helen A1 - Norlén, Hedvig A1 - Butenweg, Christoph A1 - Gervasio, Helena A1 - Manfredi, Vincenzo A1 - Masi, Angelo A1 - Zaharieva, Roumiana ED - Gkatzogias, Konstantinos ED - Tsionis, Georgios T1 - Policy practice and regional impact assessment for building renovation T2 - REEBUILD Integrated Techniques for the Seismic Strengthening & Energy Efficiency of Existing Buildings N2 - The work presented in this report provides scientific support to building renovation policies in the EU by promoting a holistic point of view on the topic. Integrated renovation can be seen as a nexus between European policies on disaster resilience, energy efficiency and circularity in the building sector. An overview of policy measures for the seismic and energy upgrading of buildings across EU Member States identified only a few available measures for combined upgrading. Regulatory framework, financial instruments and digital tools similar to those for energy renovation, together with awareness and training may promote integrated renovation. A framework for regional prioritisation of building renovation was put forward, considering seismic risk, energy efficiency, and socioeconomic vulnerability independently and in an integrated way. Results indicate that prioritisation of building renovation is a multidimensional problem. Depending on priorities, different integrated indicators should be used to inform policies and accomplish the highest relative or most spread impact across different sectors. The framework was further extended to assess the impact of renovation scenarios across the EU with a focus on priority regions. Integrated renovation can provide a risk-proofed, sustainable, and inclusive built environment, presenting an economic benefit in the order of magnitude of the highest benefit among the separate interventions. Furthermore, it presents the unique capability of reducing fatalities and energy consumption at the same time and, depending on the scenario, to a greater extent. Y1 - 2022 SN - 978-92-76-60454-9 U6 - https://doi.org/10.2760/883122 SN - 1831-9424 SP - 1 EP - 68 PB - Publications Office of the European Union CY - Luxembourg ER - TY - CHAP A1 - Weber, Felix A1 - Bomholt, Frederik A1 - Butenweg, Christoph ED - Bergmeister, Konrad ED - Fingerloos, Frank ED - Wörner, Johann-Dietrich T1 - Erdbeben- und Schwingungsschutz von Bauwerken T2 - 2023 BetonKalender: Wasserundurchlässiger Beton, Brückenbau N2 - Dieser Beitrag beschreibt die herkömmlichen Maßnahmen wie die Kapazitätsbemessung der Tragwerksstruktur, die Isolation des Bauwerks mittels Basisisolatoren, die Dämpfungserhöhung der Struktur mittels Inter-Story-Dämpfern und die Schwingungsreduktion mittels Schwingungstilgern gegen Einwirkungen durch Erdbeben, Wind, Verkehr und Personen auf die Bauwerke. Ergänzend wird die erdbebengerechte Auslegung und Isolation von nichttragenden Bauteilen behandelt. Für die betrachteten Systeme werden die Bewegungsdifferenzialgleichungen unter Berücksichtigung der wesentlichen Nichtlinearitäten angegeben. Die vorgestellten Weiterentwicklungen in den Bereichen der Basisisolatoren, Dämpfern und Schwingungstilgern zeigen, dass das modellbasierte Design mittels Simulation ein sehr effektives, ökonomisches und dank der heutigen Computerleistung auch zeiteffizientes Werkzeug darstellt. Y1 - 2022 SN - 9783433611180 SN - 9783433033753 U6 - https://doi.org/10.1002/9783433611180.ch16 N1 - Beton-Kalender, 112. Jahrgang (2023): Wasserundurchlässiger Beton, Brückenbau ausleihbar unter der Sig. 11 XCF 3-2023,2 SP - 779 EP - 859 PB - Ernst & Sohn CY - Berlin ER - TY - CHAP A1 - Evans, Benjamin A1 - Braun, Sebastian A1 - Ulmer, Jessica A1 - Wollert, Jörg T1 - AAS implementations - current problems and solutions T2 - 20th International Conference on Mechatronics - Mechatronika (ME) N2 - The fourth industrial revolution presents a multitude of challenges for industries, one of which being the increased flexibility required of manufacturing lines as a result of increased consumer demand for individualised products. One solution to tackle this challenge is the digital twin, more specifically the standardised model of a digital twin also known as the asset administration shell. The standardisation of an industry wide communications tool is a critical step in enabling inter-company operations. This paper discusses the current state of asset administration shells, the frameworks used to host them and their problems that need to be addressed. To tackle these issues, we propose an event-based server capable of drastically reducing response times between assets and asset administration shells and a multi-agent system used for the orchestration and deployment of the shells in the field. KW - Industry 4.0 KW - Multi-agent Systems KW - Digital Twin KW - Asset Administration Shell Y1 - 2022 SN - 978-1-6654-1040-3 U6 - https://doi.org/10.1109/ME54704.2022.9982933 N1 - 20th International Conference on Mechatronics - Mechatronika (ME), 07-09 December 2022, Pilsen, Czech Republic PB - IEEE CY - New York, NY ER - TY - JOUR A1 - Baringhaus, Ludwig A1 - Gaigall, Daniel T1 - A goodness-of-fit test for the compound Poisson exponential model JF - Journal of Multivariate Analysis N2 - On the basis of bivariate data, assumed to be observations of independent copies of a random vector (S,N), we consider testing the hypothesis that the distribution of (S,N) belongs to the parametric class of distributions that arise with the compound Poisson exponential model. Typically, this model is used in stochastic hydrology, with N as the number of raindays, and S as total rainfall amount during a certain time period, or in actuarial science, with N as the number of losses, and S as total loss expenditure during a certain time period. The compound Poisson exponential model is characterized in the way that a specific transform associated with the distribution of (S,N) satisfies a certain differential equation. Mimicking the function part of this equation by substituting the empirical counterparts of the transform we obtain an expression the weighted integral of the square of which is used as test statistic. We deal with two variants of the latter, one of which being invariant under scale transformations of the S-part by fixed positive constants. Critical values are obtained by using a parametric bootstrap procedure. The asymptotic behavior of the tests is discussed. A simulation study demonstrates the performance of the tests in the finite sample case. The procedure is applied to rainfall data and to an actuarial dataset. A multivariate extension is also discussed. KW - Bootstrapping KW - Collective risk model Y1 - 2022 U6 - https://doi.org/10.1016/j.jmva.2022.105154 SN - 0047-259X SN - 1095-7243 VL - 195 IS - Article 105154 PB - Elsevier CY - Amsterdam ER - TY - JOUR A1 - Tran, Ngoc Trinh A1 - Trinh, Tu Luc A1 - Dao, Ngoc Tien A1 - Giap, Van Tan A1 - Truong, Manh Khuyen A1 - Dinh, Thuy Ha A1 - Staat, Manfred T1 - FEM shakedown analysis of structures under random strength with chance constrained programming JF - Vietnam Journal of Mechanics N2 - Direct methods, comprising limit and shakedown analysis, are a branch of computational mechanics. They play a significant role in mechanical and civil engineering design. The concept of direct methods aims to determine the ultimate load carrying capacity of structures beyond the elastic range. In practical problems, the direct methods lead to nonlinear convex optimization problems with a large number of variables and constraints. If strength and loading are random quantities, the shakedown analysis can be formulated as stochastic programming problem. In this paper, a method called chance constrained programming is presented, which is an effective method of stochastic programming to solve shakedown analysis problems under random conditions of strength. In this study, the loading is deterministic, and the strength is a normally or lognormally distributed variable. KW - limit analysis KW - shakedown analysis KW - chance constrained programming KW - stochastic programming KW - reliability of structures Y1 - 2022 U6 - https://doi.org/10.15625/0866-7136/17943 SN - 0866-7136 SN - 2815-5882 VL - 44 IS - 4 SP - 459 EP - 473 PB - Vietnam Academy of Science and Technology (VAST) ER - TY - JOUR A1 - Czarnecki, Christian T1 - Moderne Telekommunikationsprodukte erfordern standardisierte Geschäftsprozesse JF - Wirtschaft und Wissenschaft Y1 - 2015 IS - 2 SP - 7 EP - 7 PB - Deutsche Telekom AG. Fachhochschule Leipzig CY - Leipzig ER - TY - CHAP A1 - Bensberg, Frank A1 - Czarnecki, Christian A1 - Grob, Heinz Lothar ED - Bruhn, Manfred ED - Hadwich, Karsten T1 - Wirtschaftlichkeitsbewertung von Smart Services mit vollständigen Finanzplänen T2 - Smart Services: Band 1: Konzepte – Methoden – Prozesse N2 - Dieser Beitrag stellt einen Bewertungsrahmen für Smart Services vor, der auf dem Konzept vollständiger Finanzpläne (VOFI) basiert. Zunächst wird eine IoT-Architektur für Smart Services eingeführt, die die Grundlage für deren Betrachtung aus Sicht der Unternehmensplanung liefert. Hierauf aufbauend wird ein Bewertungsrahmen für die finanzplanorientierte Wirtschaftlichkeitsbewertung von Smart Services geschaffen, mit dem die relevanten Zahlungsfolgen differenziert erfasst werden. Mithilfe des entwickelten VOFI-Systems wird anschließend aufgezeigt, wie mithilfe einer Risikoanalyse die Unsicherheit von Modellparametern berücksichtigt werden kann. Y1 - 2022 SN - 978-3-658-37344-3 (Online) SN - 978-3-658-37343-6 (Print) U6 - https://doi.org/10.1007/978-3-658-37344-3_6 SP - 225 EP - 251 PB - Springer Gabler CY - Wiesbaden ER - TY - CHAP A1 - Czarnecki, Christian ED - vom Brocke, Jan ED - Mendling, Jan T1 - Establishment of a central process governance organization combined with operational process improvements : Insights from a BPM Project at a leading telecommunications operator in the Middle East T2 - Business process management cases : digital innovation and business transformation in practice N2 - Because of customer churn, strong competition, and operational inefficiencies, the telecommunications operator ME Telco (fictitious name due to confidentiality) launched a strategic transformation program that included a Business Process Management (BPM) project. Major problems were silo-oriented process management and missing cross-functional transparency. Process improvements were not consistently planned and aligned with corporate targets. Measurable inefficiencies were observed on an operational level, e.g., high lead times and reassignment rates of the incident management process. Y1 - 2018 SN - 978-3-319-58306-8 SN - 978-3-319-58307-5 SN - 978-3-319-86372-6 U6 - https://doi.org/10.1007/978-3-319-58307-5 N1 - Als Präsenzexemplar unter der Signatur 20 PZR 469-1 vorhanden. SP - 57 EP - 76 PB - Springer CY - Cham ER - TY - JOUR A1 - Röthenbacher, Annika A1 - Cesari, Matteo A1 - Doppler, Christopher E.J. A1 - Okkels, Niels A1 - Willemsen, Nele A1 - Sembowski, Nora A1 - Seger, Aline A1 - Lindner, Marie A1 - Brune, Corinna A1 - Stefani, Ambra A1 - Högl, Birgit A1 - Bialonski, Stephan A1 - Borghammer, Per A1 - Fink, Gereon R. A1 - Schober, Martin A1 - Sommerauer, Michael T1 - RBDtector: an open-source software to detect REM sleep without atonia according to visual scoring criteria JF - Scientific Reports N2 - REM sleep without atonia (RSWA) is a key feature for the diagnosis of rapid eye movement (REM) sleep behaviour disorder (RBD). We introduce RBDtector, a novel open-source software to score RSWA according to established SINBAR visual scoring criteria. We assessed muscle activity of the mentalis, flexor digitorum superficialis (FDS), and anterior tibialis (AT) muscles. RSWA was scored manually as tonic, phasic, and any activity by human scorers as well as using RBDtector in 20 subjects. Subsequently, 174 subjects (72 without RBD and 102 with RBD) were analysed with RBDtector to show the algorithm’s applicability. We additionally compared RBDtector estimates to a previously published dataset. RBDtector showed robust conformity with human scorings. The highest congruency was achieved for phasic and any activity of the FDS. Combining mentalis any and FDS any, RBDtector identified RBD subjects with 100% specificity and 96% sensitivity applying a cut-off of 20.6%. Comparable performance was obtained without manual artefact removal. RBD subjects also showed muscle bouts of higher amplitude and longer duration. RBDtector provides estimates of tonic, phasic, and any activity comparable to human scorings. RBDtector, which is freely available, can help identify RBD subjects and provides reliable RSWA metrics. Y1 - 2022 U6 - https://doi.org/10.1038/s41598-022-25163-9 SN - 2045-2322 VL - 12 IS - Article number: 20886 SP - 1 EP - 14 PB - Springer Nature CY - London ER - TY - JOUR A1 - Mueller, Tobias A1 - Segin, Alexander A1 - Weigand, Christoph A1 - Schmitt, Robert H. T1 - Feature selection for measurement models JF - International journal of quality & reliability management N2 - Purpose In the determination of the measurement uncertainty, the GUM procedure requires the building of a measurement model that establishes a functional relationship between the measurand and all influencing quantities. Since the effort of modelling as well as quantifying the measurement uncertainties depend on the number of influencing quantities considered, the aim of this study is to determine relevant influencing quantities and to remove irrelevant ones from the dataset. Design/methodology/approach In this work, it was investigated whether the effort of modelling for the determination of measurement uncertainty can be reduced by the use of feature selection (FS) methods. For this purpose, 9 different FS methods were tested on 16 artificial test datasets, whose properties (number of data points, number of features, complexity, features with low influence and redundant features) were varied via a design of experiments. Findings Based on a success metric, the stability, universality and complexity of the method, two FS methods could be identified that reliably identify relevant and irrelevant influencing quantities for a measurement model. Originality/value For the first time, FS methods were applied to datasets with properties of classical measurement processes. The simulation-based results serve as a basis for further research in the field of FS for measurement models. The identified algorithms will be applied to real measurement processes in the future. KW - Feature selection KW - Modelling KW - Measurement models KW - Measurement uncertainty Y1 - 2022 U6 - https://doi.org/10.1108/IJQRM-07-2021-0245 SN - 0265-671X IS - Vol. ahead-of-print, No. ahead-of-print. PB - Emerald Group Publishing Limited CY - Bingley ER - TY - BOOK A1 - Tünnemann, Thomas T1 - Formine 2022 : Concezione I N2 - Der diesjährige Workshop steht im Zeichen der räumlichen Konzeption. Das Definieren und Erfahren des engsten, ganz eigenen Betrachtungsraums, bis hin zur weitläufigen öffentlichen Umgebung des Ortes ist hierbei der erste Schritt. Hierzu stehen alle konzeptionellen Werkzeuge – von der Entwicklung vereinzelter Skizzenabfolgen, bis hin zur Collage - in den ersten Tagen des Workshops zur Verfügung. Abschließend gilt es, den Aufbau - das „Sichzusammenfügen“ aus Form, Relation und Material - in einer Plastik zu vereinen. Y1 - 2022 SN - 3-9811003-9-5 PB - FH Aachen, Fachbereich Architektur CY - Aachen ER - TY - CHAP A1 - Fissabre, Anke ED - Soldwisch, Ines ED - Schmitz, Stefan T1 - kirchen-bauhaus? – Die Kunstgewerbeschule in Aachen unter Rudolf Schwarz T2 - Zwischen den Zeiten - Besatzung und Aufbruch in Aachen, 1919-1932 Y1 - 2022 SN - 978-3-9825016-0-4 N1 - Zeitreisen Sammlung Crous, Schriftenreihe 15. SP - 54 EP - 65 PB - Aachener Karnevalsverein (AKV) CY - Aachen ER - TY - THES A1 - Keller, Simon Mark T1 - Risikoanalyse einer bordautonomen Schienenfahrzeugortung mittels GNSS N2 - Bei Schienenfahrzeugen, die mit dem Zugsicherungssystem ETCS betrieben sind, wird die Odometrie durch eine diskrete Ortung mittels physischen Balisen zurückgesetzt. Diese Arbeit befasst sich mit der Innovation von virtuellen Balisen. Virtuelle Balisen, können eingesetzt werden, um physische, im Gleisbett montierte Balisen zu ersetzen. Durch den Einsatz von virtuellen Balisen soll der Infrastrukturausbau von ETCS vorangetrieben werden, indem sie als virtuelle Komponente auf Schienenfahrzeugen eingesetzt werden. Im Rahmen dieser Arbeit wird die Fragestellung beantwortet, ob eine bordautonome Zugortung mittels virtuellen Balisen in einem ausgewählten Szenario mit einem akzeptablen Risiko verbunden ist? Das Szenario besteht aus einem Schienenfahrzeug, welches mit dem Zugsicherungssystem ETCS Level 2 auf einer eingleisigen Nebenstrecke betreiben wird. Hierzu werden zunächst die Grundlagen von ETCS und der satellitenbasierten Ortung erläutert. Des Weiteren werden die Grundlagen des CSM Prozesses und der expliziten Risikoabschätzung eingeführt. Aufbauend auf diesen Grundlagen wird der CSM Prozess angewandt und dabei eine Systemdefinition mit den Schnittstellen des Systems zur Umwelt erstellt. Mit der Hazop-Methode werden die Gefährdungen der Schnittstellen erfasst und beurteilt. Die sicherheitsrelevanten Gefährdungen werden in einer FMEA bewertet. In der folgenden Diskussion werden sicherheitsrelevante Gefährdungen nochmals betrachtet. Das Ergebnis der Arbeit ist, dass im ausgewählten Szenario, unter der Verwendung der CSM-Prozesse und der industriell anerkannten Methoden Hazop und FMEA, die Integration der Board-autonomen-Ortung mit einem akzeptablen Risiko verbunden ist. Y1 - 2022 PB - FH Aachen CY - Aachen ER - TY - BOOK A1 - Bundrock, Ronja A1 - Kremers, Nico A1 - Pankok, Lennard A1 - Weisheit, Theresa Maria A1 - Spoede, Jasper ED - Kroll-Ludwigs, Kathrin ED - Bernecker, Andreas ED - Bassen-Metz, Yasmine ED - Eggert, Mathias ED - Fritz, Thomas ED - Golland, Alexander ED - Höhne, Tim ED - Tran, Duc Hung ED - Vogt, Jürgen T1 - Aachener Online-Schriften Wirtschaft und Recht. Band 5. 02/2022 N2 - Inhaltsverzeichnis - Bachelorarbeiten 1. Testamentsgestaltung bei Patchworkfamilien – Lösungsansätze für typische Praxisprobleme unter Berücksichtigung der Interessenlagen der Parteien - Ronja Bundrock 4 - 58 2. Die Haftung des AG-Vorstands gegenüber der Gesellschaft in unterneh- mensinternen und -externen Krisen - Nico Kremers 59 - 122 3. The Relationship of the Ex-Ante Uncertainty about the Value of a Stock and its IPO Underpricing – An Analysis of the German Market - Lennard Pankok 123 - 179 4. Attractiveness Bias in Venture Capital – An Analysis of Investor Decision Making in “Die Höhle der Löwen” - Theresa Maria Weisheit 180 - 242 Inhaltsverzeichnis – Masterarbeiten Erhöhung der Energieautarkie in der Backbranche – Anwendung von bidi- rektionalem Laden und dessen Auswirkungen auf die Geschäftsprozesse und Informationssysteme - Jasper Spoede 243 - 355 T3 - Aachener Online-Schriften Wirtschaft und Recht - 5 Y1 - 2022 PB - FH Aachen / Fachbereich Wirtschaftswissenschaften CY - Aachen ER - TY - CHAP A1 - Hauk, Joachim A1 - Czarnecki, Christian A1 - Dietze, Christian ED - Rusnjak, Andreas ED - Schallmo, Daniel R. A. T1 - Prozessorientierte Messung der Customer Experience am Beispiel der Telekommunikationsindustrie T2 - Customer Experience im Zeitalter des Kunden : Best Practices, Lessons Learned und Forschungsergebnisse N2 - Hohe Wettbewerbsintensität und gestiegene Kundenanforderungen erfordern bei Telekommunikationsunternehmen eine aktive Gestaltung der Customer Experience (CX). Ein wichtiger Aspekt dabei ist die CX-Messung. Traditionelle Zufriedenheitsmessungen sind oft nicht ausreichend, um die Kundenerfahrung in komplexen Prozessen vollständig zu erfassen. Daher wird in diesem Kapitel eine prozessübergreifende Referenzlösung zur CX-Messung am Beispiel der Telekommunikationsindustrie vorgeschlagen. Ausgangspunkt ist ein industriespezifisches Prozessmodell, das sich an dem Referenzmodell eTOM orientiert. Dieses wird um Messpunkte erweitert, die Schwachstellen in Bezug auf die CX identifizieren. Für die erkannten Schwachstellen werden über eine Referenzmatrix mögliche Auslöser abgeleitet und anhand von typischen Geschäftsfallmengen bewertet. Somit ist eine direkte Zuordnung und Erfolgsmessung konkreter Maßnahmen zur Behebung der Schwachstellen möglich. Die so entwickelte Referenzlösung wurde im Projekt K1 bei der Deutschen Telekom erfolgreich umgesetzt. Details zur Umsetzung werden als Fallstudien dargestellt. Y1 - 2018 SN - 978-3-658-18961-7 SN - 978-3-658-18960-0 U6 - https://doi.org/10.1007/978-3-658-18961-7_7 SP - 195 EP - 216 PB - Springer Gabler CY - Wiesbaden ER - TY - THES A1 - Laubkermeier, Kim T1 - trust me N2 - "trust me" ist eine schwarz-weiß Fotoserie, präsentiert als Diashow mit unterlegtem Soundtrack. Es geht um das Vertrauen zwischen Model, Fotografin und Betrachter:innen. Die Darsteller sind ausschließlich homosexuelle Männer und begeben sich in intime Situationen und Posen. Die Fotos sind überwiegend Aktaufnahmen und nehmen eine pornografische Richtung an. Die Fragestellung zu Beginn war, wie weit vertrauen die unerfahrenen Models der Fotografin und was sind diese bereit, von sich zu zeigen. Die offene Kommunikation über die Richtung des Projekts war die essenzielle Basis für die Fotoshootings. Während des Fotografierens lag der Fokus auf möglichst verschiedenen Blickwinkeln, Kulissen, Ausleuchtungen und Motiven. Zusätzlich war der sensible Umgang mit den Männern eine Vertrauensprobe."trust me" lässt auf diversen Ebenen tief blicken und zeigt, wie loslassen aussieht. KW - Fotografie KW - schwarz-weiß KW - Diashow KW - Vertrauen KW - Portraits Y1 - 2022 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER - TY - GEN A1 - Steuer-Dankert, Linda A1 - Bernhard, Sebastian A1 - Langolf, Jessica A1 - Leicht-Scholten, Carmen T1 - Managing change and acceptance of digitalization strategies - Implementing the vision of „Internet of Production“ (IoP) in existing corporate structures T2 - Textile Impulse für die Zukunft: Aachen-Dresden-Denkendorf International Textile Conference 2022 N2 - The vision of the Internet of Production is to enable a new level of crossdomain collaboration by providing semantically adequate and context-aware data from production, development & usage in real-time. Y1 - 2022 N1 - Textile Impulse für die Zukunft: Aachen-Dresden-Denkendorf International Textile Conference 2022 : 1. – 2. Dezember 2022, Eurogress Aachen SP - 153 EP - 153 ER - TY - CHAP A1 - Schneider, Dominik A1 - Wisselink, Frank A1 - Czarnecki, Christian ED - Barton, Thomas ED - Müller, Christian ED - Seel, Christian T1 - Nutzen und Rahmenbedingungen 5 informationsgetriebener Geschäftsmodelle des Internets der Dinge T2 - Digitalisierung in Unternehmen: von den theoretischen Ansätzen zur praktischen Umsetzung N2 - Im Kontext der zunehmenden Digitalisierung wird das Internet der Dinge (englisch: Internet of Things, IoT) als ein technologischer Treiber angesehen, durch den komplett neue Geschäftsmodelle im Zusammenspiel unterschiedlicher Akteure entstehen können. Identifizierte Schlüsselakteure sind unter anderem traditionelle Industrieunternehmen, Kommunen und Telekommunikationsunternehmen. Letztere sorgen mit der Bereitstellung von Konnektivität dafür, dass kleine Geräte mit winzigen Batterien nahezu überall und direkt an das Internet angebunden werden können. Es sind schon viele IoT-Anwendungsfälle auf dem Markt, die eine Vereinfachung für Endkunden darstellen, wie beispielsweise Philips Hue Tap. Neben Geschäftsmodellen basierend auf Konnektivität besteht ein großes Potenzial für informationsgetriebene Geschäftsmodelle, die bestehende Geschäftsmodelle unterstützen sowie weiterentwickeln können. Ein Beispiel dafür ist der IoT-Anwendungsfall Park and Joy der Deutschen Telekom AG, bei dem Parkplätze mithilfe von Sensoren vernetzt und Autofahrer in Echtzeit über verfügbare Parkplätze informiert werden. Informationsgetriebene Geschäftsmodelle können auf Daten aufsetzen, die in IoT-Anwendungsfällen erzeugt werden. Zum Beispiel kann ein Telekommunikationsunternehmen Mehrwert schöpfen, indem es aus Daten entscheidungsrelevantere Informationen – sogenannte Insights – ableitet, die zur Steigerung der Entscheidungsagilität genutzt werden. Außerdem können Insights monetarisiert werden. Die Monetarisierung von Insights kann nur nachhaltig stattfinden, wenn sorgfältig gehandelt wird und Rahmenbedingungen berücksichtigt werden. In diesem Kapitel wird das Konzept informationsgetriebener Geschäftsmodelle erläutert und anhand des konkreten Anwendungsfalls Park and Joy verdeutlicht. Darüber hinaus werden Nutzen, Risiken und Rahmenbedingungen diskutiert. KW - Digitale Transformation KW - Internet der Dinge KW - Monetarisierung KW - Informationsgetriebene Geschäftsmodelle KW - Qualitative Wertschöpfungsanalyse Y1 - 2018 SN - 9783658227739 SN - 9783658227722 U6 - https://doi.org/10.1007/978-3-658-22773-9_5 SP - 67 EP - 85 PB - Springer CY - Wiesbaden ER - TY - THES A1 - Ioannidou, Martha T1 - Master of Procrastination N2 - In den letzten Jahren ist das Thema “Prokrastinieren” omnipräsent geworden. Gegensätzlich dazu versuchen immer mehr Menschen sich zu optimieren. Ziel dieser Arbeit ergibt sich in der Verbindung dieser paradoxen Vorgänge. Im Video wird nicht nur der Begriff Prokrastinieren erklärt, sondern auch ein faktisch basierter Leitfaden zum verbesserten Aufschieben präsentiert. Der Zuschauer kann sich in humoristisch und ironischer Art mit der Thematik auseinandersetzten, Ohne sich mit der negativen Konnotation zu beschäftigen. “Master of Procrastination” eröffnet einen neuen Blickwinkel und informierten Gleichermaßen zu einer unbeliebten Problematik. KW - Prokrastinieren KW - Aufschieben KW - Aufschieberitis KW - Machichmorgen KW - Leitfaden Y1 - 2022 PB - FH Aachen CY - Aachen ER - TY - THES A1 - Koscielniak, Luise T1 - Das Ludwig Forum Aachen : die Erstellung eines neuen Erscheinungsbildes N2 - Peter und Irene Ludwig galten als das Kunstsammlerpaar Deutschlands. Sie stellten ihre umfangreiche Sammlung der Öffentlichkeit zur Verfügung, so auch dem Ludwig Forum - das Stammmuseum der beiden Aachener. Doch es ist viel mehr als nur ein Museum. Der Gedanke des Forums als einen Ort des Austausches und der Kommunikation mit und über Kunst ist die leittragende Idee. Das neue Erscheinungsbild leitet sich in der Gestaltung bildlich von diesem Forumsgedanken ab. Zur Visualisierung dieser Idee wurden Kommunikationsachsen aufgegriffen, die zur typografischen Ausrichtung genutzt werden. Sie bieten die Möglichkeit, in verschiedene Richtungen zu kommunizieren und Inhalte vielseitig und prägnant zu visualisieren. Die Wortmarke des Ludwig Forums dient dabei als klammerndes Element, welches den Rahmen für die Gestaltung ermöglichen. Mit der Fokussierung auf den Forumsgedanken setzt sich das Ludwig Forum sowohl inhaltlich als nun auch gestalterisch von anderen Museumseinrichtungen ab. KW - Erscheinungsbild KW - Ludwig Forum KW - Forum KW - Kommunikation KW - Dialog Y1 - 2022 PB - FH Aachen CY - Aachen ER - TY - THES A1 - Larscheid, Maja Marlene T1 - The Future of Fitness : Konzeption und Gestaltung einer digitalen Fitness- und Gesundheitsanwendung N2 - Laut einer Langzeitstudie bewegt sich mehr als ein Viertel der Weltbevölkerung – rund 2 Milliarden Menschen – zu wenig. Trotzdem ließ sich zuletzt klares Interesse an Fitness- und Gesundheitsmöglichkeiten am stetigen Anstieg der Fitnessstudio-Mitgliederzahl erkennen. Nachdem die Zahl seit 2006 jedes Jahr anstieg, fiel sie in den Pandemie-Jahren. Seit der Pandemie besteht also Bedarf nach einer flexibleren Lösung zu klassischen Studios. Um diesen Bedarf zu decken, wurde eine digitale Lösung zum Thema entwickelt. Dazu wurden Sport und Ernährung zusammengefasst. Das beinhaltet Videoanleitungen, Ernährungs- und Trainingsplanerstellung, individuelle Körperanalyse im Onboarding-Prozess, Verbindung mit Wearables und ein flexibles Online- sowie Studioangebot. Meine Zielgruppe sind Menschen, die flexibel Sport machen, mit Sport anfangen oder ihre allgemeine Gesundheit verbessern wollen. KW - Fitness KW - Gesundheit KW - Ernährung KW - Sport KW - UXDesign Y1 - 2022 PB - FH Aachen CY - Aachen ER - TY - THES A1 - Lenz, Lena T1 - Frauen sind der Boss : eine Kampagne für mehr Gleichberechtigung in Führungspositionen N2 - Man könnte vermuten, dass in einem so weit entwickelten Land wie Deutschland Geschlechterdiskriminierung bereits erfolgreich überwunden wurde – doch das entspricht nicht der Realität. Besonders in Führungspositionen fällt dieses Ungleichgewicht auf. Eine Ursache dafür ist das historisch etablierte Rollenverständnis, aber auch vonseiten der Frauen gibt es häufig ein grundlegendes Problem: Sie trauen sich zu wenig zu. Die Kampagne soll junge Frauen dazu motivieren, ihre beruflichen Ambitionen hoch anzusetzen und zielstrebig zu verfolgen. Das Online-Portal "femiverse" ist dabei ihr Wegbereiter. Es ermöglicht einen direkten Austausch mit anderen Nutzer:innen und eröffnet durch Workshops mit Unternehmer:innen neue Perspektiven. Die Bezeichnung „Powerfrau“ ist überholt – Frauen in Führungspositionen sind keine Ausnahmetalente, sie sind die Normalität von morgen. KW - Kampagne KW - Geschlechtergerechtigkeit KW - Gleichberechtigung KW - Frauen KW - Beruf Y1 - 2022 PB - FH Aachen CY - Aachen ER - TY - THES A1 - Neumann, Julius T1 - Traces of urban change N2 - Eine Stadt ist das Ergebnis eines komplexen Urbanisierungsprozesses. Dieser ist vor allem dadurch bestimmt, dass immer mehr Menschen in Städten leben. Das Wachstum und Altern von Städten machen ständige räumliche und bauliche Veränderungen erforderlich. Die Bachelorarbeit verdeutlicht diese strukturellen Veränderungen der Stadt Aachen anhand von analogen Fotografien im Jahr 2022. Dabei werden Spuren aus unterschiedlichen Zeiten betrachtet und natürliche oder durch den Menschen beeinflusste Veränderungen in Form von Verfall, Nutzung und Erneuerung aufgezeigt. Ziel ist es, den Blick auf Details des urbanen Wandels zu richten, um diesen wahrnehmbar und bewusst zu machen. Die Betrachter:innen sollen zum Nachdenken und genauen Hinschauen angeregt werden. Die Fotografien versuchen den zurückliegenden Veränderungsprozess erkennen zu lassen und damit gewissermaßen dessen Geschichte abzubilden. KW - Fotografie KW - analog KW - Bildband KW - Aachen KW - Stadt Y1 - 2022 PB - FH Aachen CY - Aachen ER - TY - THES A1 - Pauly, Tim Christian T1 - Fantasy : Die Gefahren des Internets und der Sozialen Medien in Bezug auf Kinder N2 - Anhand der Geschichte des Protagonisten Max, wird auf die Gefahr des Internets und der Sozialen Medien hinsichtlich Kinder aufmerksam gemacht. Kinder sind im Internet einigen Gefahren ausgesetzt und ihre Eltern sind sich dessen oftmals kaum bewusst oder haben Probleme, das Tun der Kinder im Auge zu behalten. Die Geschichte wird durch die Lyrik eines Liedes erzählt. Im dazugehörigen Musikvideo bekommen die Zuschauer:innen einen Einblick in Max Leben und sein Leid. Des Weiteren ist zu sehen, wie Max den Täter verurteilt, seine Fantasie gestohlen zu haben. Unklar bleibt, ob sein Auftreten währenddessen in der Wirklichkeit oder aus seiner verbliebenen Fantasie heraus passiert. Sein schweres Schicksal, ausgedrückt mit aller Härte, soll den Zuschauenden schockierend auf die Problematik aufmerksam machen. Das Projekt soll helfen, diese fehlende Aufmerksamkeit einzudämmen. KW - Fantasie KW - Internet KW - Soziale Medien KW - Missbrauch KW - Bedrohung Y1 - 2022 PB - FH Aachen CY - Aachen ER - TY - THES A1 - Koenen, Rachel A1 - Pohlen, Britta T1 - Energie zur Teilhabe : Etablierung einer Plattform zum Ausbau der Energiewende für städtische Mieter N2 - Die gelungene Energiewende ist essenziell auf dem Weg zur geplanten Klimaneutralität bis 2045. Möglichkeiten für Immobilienbesitzer:innen, sich am Ausbau erneuerbarer Energien zu beteiligen, sind überwiegend bekannt. Mieter:innen im urbanen Raum werden jedoch nicht adäquat darüber aufgeklärt, wie auch sie teilhaben können. Die Online-Plattform „energiewende-teilhaben.de"" zentriert Wissen und schlägt konkrete personalisierte Maßnahmen zur Partizipation vor. Eine Werbekampagne etabliert die Plattform im städtischen Raum und zeigt bereits motivierten Mieter:innen einfache Möglichkeiten zur Beteiligung auf. Durch eine hohe Sichtbarkeit der wachsenden Community werden noch Unbeteiligte angesteckt und die Wende in der Stadt ausgelöst. Die Kampagne lenkt die Motivationsenergie der Bevölkerung über die Plattform auf Teilhabe und Klimaschutz. KW - Energiewende KW - erneuerbare Energien KW - Strom KW - Stadt KW - Mieter Y1 - 2022 PB - FH Aachen CY - Aachen ER - TY - THES A1 - Puzich, Simon T1 - komuniiio : Generationenaustausch & Engagement neu gedacht N2 - Aktuelle Ehrenämter und Möglichkeiten des Austauschs sind in alten Strukturen festgefahren und erfahren wenig Aufmerksamkeit. Die Potenziale von älteren Generationen werden zu selten geschätzt und ausgeschöpft. Dazu werden Sie in vielen neuen Dingen und Anwendungen nicht als Nutzer:innengruppe beachtet und somit Schritt für Schritt ausgegrenzt. Der Ansatz dieser Arbeit war es, eine gesellschaftlich fördernde digitale Oberfläche für den Generationenaustausch zwischen jung und alt zu schaffen - unabhängig von Vereinsstrukturen oder Organisationen. Vereinen wir das Bewusstsein der Alten mit der Neugier und Innovationskraft der Jungen, um eine Zukunft zu schaffen, in der es sich lohnt, jung zu sein, als auch alt zu werden. KW - Generationenaustausch KW - Accessability KW - Inklusion KW - Community KW - Sozial Y1 - 2022 PB - FH Aachen CY - Aachen ER - TY - THES A1 - Roentgen, Matthis T1 - Ketten, die die Welt umspannen : wie funktioniert Blockchain-Technologie und was kann sie uns bieten? N2 - Bitcoins und NFTs sind längst keine Neuheit mehr und vielen bereits ein Begriff. Doch was genau steckt hinter digitalen Währungen und kryptografischen Tokens? »Ketten, die die Welt umspannen« ist die erste Ausgabe des »101.mag« und setzt sich mit dieser Frage auseinander. Das Magazin versucht über ein unkonventionelles Layout, interessante Artikel und spannende Illustrationen seine Leser:innen in die Welt der vielversprechenden Technologie einzuführen. Die Kommunikationen zwischen Mensch und Computer steht nicht nur thematisch im Mittelpunkt dieser Arbeit. Auch die Gestaltung profitiert von dieser Zusammenarbeit. So wurde der Fließtext mithilfe eines Processing-Tools über das Raster verteilt. Auch die Illustration wurde über ein weiteres Programm in verpixelte Grafiken umgewandelt. Die statischen Bild- und Textelemente werden durch kleine Animationen ergänzt. Diese werden im digitalen Raum eingesetzt und unterstützen so das gesamte Konzept auf multimedialer Ebene. Das Ergebnis ist ein besonderes Magazin, welches eine neue Richtung einschlägt. KW - Editorial KW - generische Gestaltung KW - Layout KW - Magazin KW - Blockchain Y1 - 2022 PB - FH Aachen CY - Aachen ER - TY - THES A1 - Schmalfuss, Vanessa Dana T1 - LGBTQIA+ : Aufklärungskampagne für die Reduzierung des Gebrauchs von Schimpfwörtern an Schulen N2 - Der Missbrauch von Schimpfwörtern im Bereich Schule, die sich gegen LGBTQIA+ richten, ist nach wie vor ein ernst zu nehmendes Problem. Durch eine Aufklärungskampagne wird diesem Problem entgegengewirkt. Da man den Schüler:innen das Benutzen von Schimpfwörtern nicht ganz abgewöhnen kann, wird ihnen durch die Kampagne vorgemacht, wie man besser, cooler und intelligenter schimpft. Durch das Motto "Richtig schimpfen ganz unkompliziert" zeigt die Kampagne den Schüler:innen, wie man auf eine smarte Art und Weise mit Worten umgeht und gleichzeitig den eigenen Gebrauch von Schimpfwörtern reflektiert. KW - LGBTQIA+ KW - Aufklärungskampagne KW - Schule KW - Schimpfwörter Y1 - 2022 PB - FH Aachen CY - Aachen ER - TY - THES A1 - Sehl, Kristina T1 - Adapt or die : Heimische Wälder im Wandel durch Mensch und Zeit N2 - Wo einst fast lückenlos Laubwälder wuchsen, steht heute nur noch ein Drittel der ursprünglichen Waldfläche. Echte Urwälder gibt es hier schon lange nicht mehr: Die Rede ist vom deutschen Wald. Unsere Welt ist im Wandel. Auch in unseren heimischen Wäldern lassen sich die Einflüsse von Mensch und Klimawandel auf die Biodiversität beobachten. Die illustrierte Publikation „Adapt or die“ lädt mit mehr als 80 großformatigen Artenportraits, Habitat-Kartierungen und gestalteten Themenklappenseiten zur Auseinandersetzung mit dem Wandel unserer heimischen Wälder ein. Dabei sensibilisiert sie für einen bewussteren Umgang mit Umwelt und Natur. Erweiterungen durch Augmented Reality bieten vereinzelt neben dem Printprodukt aktualisierbare Prognosen, digital und ressourcenschonend. Das komplexe Ökosystem des Waldes reagiert empfindlich auf Veränderungen: Wer sich nicht anpassen kann, wird verschwinden. KW - Wald KW - Lebensraum KW - Wandel KW - Artenvielfalt KW - Biodiversität Y1 - 2022 PB - FH Aachen CY - Aachen ER - TY - THES A1 - Steimel, Nina T1 - An den Rand gedrängt : die Marginalisierung unserer Städte N2 - In der Arbeit »An den Rand gedrängt–Die Marginalisierung unserer Städte« wird anhand des Flächenverbrauchs des ruhenden Verkehrs erörtert, inwieweit der private Pkw die Entwicklung unserer Städte bestimmt. Die Zusammenstellung verschiedener Texte, Raumbeobachtungen und fotografischer Zeitdokumente soll die Problematik und Aktualität des Themas verstärken. Schritt für Schritt sollen die Leser:innen einen neuen Blick auf die eigene Stadt gewinnen und für das Problem der akuten Flächenknappheit sensibilisiert werden. Das Werk versteht sich als Aufruf, unseren Straßenraum zu entkarbonisieren, ihn neu zu entdecken und die möglichen Chancen im Wandel zu erkennen. Dabei geht es zunächst nicht um die Aufzählung von Klimaschäden, die Abschaffung von Parkplätzen oder gar des Autos, sondern um die Auswirkungen, die Parkplätze auf unser Leben haben und vor allem um ihr Potenzial für die Zukunft. KW - Parkplatz KW - Raumnot KW - Verkehrswende KW - Autofrei KW - Mobilitätswende Y1 - 2022 PB - FH Aachen CY - Aachen ER - TY - THES A1 - Surowiec, Julia Andrea T1 - Das wahre Gewicht des Smartphones : eine informative Erfahrung zu den ökologischen Auswirkungen N2 - Das Smartphone gehört zu den innovativsten Geräten unserer Zeit und befindet sich in einem ständigen Wandel, der nach immer mehr Leistung, größeren Displays und besseren Kameras strebt. Mit neuen Modellen, die jährlich auf den Markt kommen und den Milliarden Smartphones, die verkauft werden, entsteht aber nicht nur ein großer Markt voller Angebote, sondern gleichzeitig große Probleme für unsere Umwelt und letztlich auch für uns. Die Smartphone-Industrie schadet massiv unserem Ökosystem. Das Ziel der Arbeit ist die Aufklärung über die Auswirkungen der Smartphone-Industrie. Dafür wurden Visualisierung zu Daten und Prozessen gestaltet, die viele Aspekte des Lebenszyklus des Smartphones mit einbeziehen. Die Betrachter:innen sollen so informativ aufgeklärt werden, ihren eigenen Konsum zu dem Thema überdenken und ein Bewusstsein für ihren Elektronikverbrauch entwickeln. KW - Mobiltelefon KW - Ökonomie KW - Ökologie KW - Rohstoffgewinnung KW - Wegwerfgesellschaft Y1 - 2022 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER - TY - CHAP A1 - Czarnecki, Christian A1 - Auth, Gunnar ED - Barton, Thomas ED - Müller, Christian ED - Seel, Christian T1 - Prozessdigitalisierung durch Robotic 7 Process Automation T2 - Digitalisierung in Unternehmen: von den theoretischen Ansätzen zur praktischen Umsetzung N2 - Im Rahmen der digitalen Transformation werden innovative Technologiekonzepte, wie z. B. das Internet der Dinge und Cloud Computing als Treiber für weitreichende Veränderungen von Organisationen und Geschäftsmodellen angesehen. In diesem Kontext ist Robotic Process Automation (RPA) ein neuartiger Ansatz zur Prozessautomatisierung, bei dem manuelle Tätigkeiten durch sogenannte Softwareroboter erlernt und automatisiert ausgeführt werden. Dabei emulieren Softwareroboter die Eingaben auf der bestehenden Präsentationsschicht, so dass keine Änderungen an vorhandenen Anwendungssystemen notwendig sind. Die innovative Idee ist die Transformation der bestehenden Prozessausführung von manuell zu digital, was RPA von traditionellen Ansätzen des Business Process Managements (BPM) unterscheidet, bei denen z. B. prozessgetriebene Anpassungen auf Ebene der Geschäftslogik notwendig sind. Am Markt werden bereits unterschiedliche RPA-Lösungen als Softwareprodukte angeboten. Gerade bei operativen Prozessen mit sich wiederholenden Verarbeitungsschritten in unterschiedlichen Anwendungssystemen sind gute Ergebnisse durch RPA dokumentiert, wie z. B. die Automatisierung von 35 % der Backoffice-Prozesse bei Telefonica. Durch den vergleichsweise niedrigen Implementierungsaufwand verbunden mit einem hohen Automatisierungspotenzial ist in der Praxis (z. B. Banken, Telekommunikation, Energieversorgung) ein hohes Interesse an RPA vorhanden. Der Beitrag diskutiert RPA als innovativen Ansatz zur Prozessdigitalisierung und gibt konkrete Handlungsempfehlungen für die Praxis. Dazu wird zwischen modellgetriebenen und selbstlernenden Ansätzen unterschieden. Anhand von generellen Architekturen von RPA-Systemen werden Anwendungsszenarien sowie deren Automatisierungspotenziale, aber auch Einschränkungen, diskutiert. Es folgt ein strukturierter Marktüberblick ausgewählter RPA-Produkte. Anhand von drei konkreten Anwendungsbeispielen wird die Nutzung von RPA in der Praxis verdeutlicht. KW - Prozessautomatisierung KW - Geschäftsprozessmanagement KW - Softwareroboter KW - Digitale Transformation KW - Projektbeispiele Y1 - 2018 SN - 9783658227739 SN - 9783658227722 U6 - https://doi.org/10.1007/978-3-658-22773-9_7 SP - 113 EP - 131 PB - Springer CY - Wiesbaden ER - TY - CHAP A1 - Schmitz, Manfred A1 - Dietze, Christian A1 - Czarnecki, Christian ED - Urbach, Nils ED - Röglinger, Maximilian T1 - Enabling digital transformation through robotic process automation at Deutsche Telekom T2 - Enabling digital transformation through robotic process automation at Deutsche Telekom N2 - Due to the high number of customer contacts, fault clearances, installations, and product provisioning per year, the automation level of operational processes has a significant impact on financial results, quality, and customer experience. Therefore, the telecommunications operator Deutsche Telekom (DT) has defined a digital strategy with the objectives of zero complexity and zero complaint, one touch, agility in service, and disruptive thinking. In this context, Robotic Process Automation (RPA) was identified as an enabling technology to formulate and realize DT’s digital strategy through automation of rule-based, routine, and predictable tasks in combination with structured and stable data. Y1 - 2019 SN - 978-3-319-95272-7 U6 - https://doi.org/10.1007/978-3-319-95273-4_2 SP - 15 EP - 33 PB - Springer CY - Cham ER - TY - CHAP A1 - Bensberg, Frank A1 - Buscher, Gandalf A1 - Czarnecki, Christian ED - Nissen, Volker T1 - Digital transformation and IT topics in the consulting industry: a labor market perspective T2 - Advances in consulting research : recent findings and practical cases N2 - Information technologies, such as big data analytics, cloud computing, cyber physical systems, robotic process automation, and the internet of things, provide a sustainable impetus for the structural development of business sectors as well as the digitalization of markets, enterprises, and processes. Within the consulting industry, the proliferation of these technologies opened up the new segment of digital transformation, which focuses on setting up, controlling, and implementing projects for enterprises from a broad range of sectors. These recent developments raise the question, which requirements evolve for IT consultants as important success factors of those digital transformation projects. Therefore, this empirical contribution provides indications regarding the qualifications and competences necessary for IT consultants in the era of digital transformation from a labor market perspective. On the one hand, this knowledge base is interesting for the academic education of consultants, since it supports a market-oriented design of adequate training measures. On the other hand, insights into the competence requirements for consultants are considered relevant for skill and talent management processes in consulting practice. Assuming that consulting companies pursue a strategic human resource management approach, labor market information may also be useful to discover strategic behavioral patterns. Y1 - 2019 SN - 978-3-319-95998-6 SN - 978-3-030-07125-7 SN - 978-3-319-95999-3 U6 - https://doi.org/10.1007/978-3-319-95999-3_16 SP - 341 EP - 357 PB - Springer CY - Cham ER - TY - CHAP A1 - Fiedler, Gerda A1 - Gottschlich-Müller, Birgit A1 - Melcher, Karin ED - Liu-Henke, Xiaobo ED - Durak, Umut T1 - Online-Prüfungen mit STACK Aufgaben T2 - Tagungsband ASIM Workshop STS/GMMS/EDU 2021 N2 - Wir stellen hier exemplarisch STACK Aufgaben vor, die frei von der Problematik sind, welche sich durch diverse Kommunikationswege und (webbasierte) Computer Algebra Systeme (CAS) ergibt. Daher sind sie insbesondere für eine Open-Book Online Prüfung geeignet, da eine faire Prüfungssituation gewährleistet werden kann. Y1 - 2021 SN - 978-3-901608-69-8 U6 - https://doi.org/10.11128/arep.45 N1 - Virtueller Workshop, ASIM STS/GMMS & EDU 2021, 11.-12. März 2021 SP - 173 EP - 178 PB - ARGESIM Verlag CY - Wien ER - TY - JOUR A1 - Rübbelke, Dirk A1 - Vögele, Stefan A1 - Grajewski, Matthias A1 - Zobel, Luzy T1 - Hydrogen-based steel production and global climate protection: An empirical analysis of the potential role of a European cross border adjustment mechanism JF - Journal of Cleaner Production N2 - The European Union's aim to become climate neutral by 2050 necessitates ambitious efforts to reduce carbon emissions. Large reductions can be attained particularly in energy intensive sectors like iron and steel. In order to prevent the relocation of such industries outside the EU in the course of tightening environmental regulations, the establishment of a climate club jointly with other large emitters and alternatively the unilateral implementation of an international cross-border carbon tax mechanism are proposed. This article focuses on the latter option choosing the steel sector as an example. In particular, we investigate the financial conditions under which a European cross border mechanism is capable to protect hydrogen-based steel production routes employed in Europe against more polluting competition from abroad. By using a floor price model, we assess the competitiveness of different steel production routes in selected countries. We evaluate the climate friendliness of steel production on the basis of specific GHG emissions. In addition, we utilize an input-output price model. It enables us to assess impacts of rising cost of steel production on commodities using steel as intermediates. Our results raise concerns that a cross-border tax mechanism will not suffice to bring about competitiveness of hydrogen-based steel production in Europe because the cost tends to remain higher than the cost of steel production in e.g. China. Steel is a classic example for a good used mainly as intermediate for other products. Therefore, a cross-border tax mechanism for steel will increase the price of products produced in the EU that require steel as an input. This can in turn adversely affect competitiveness of these sectors. Hence, the effects of higher steel costs on European exports should be borne in mind and could require the cross-border adjustment mechanism to also subsidize exports. Y1 - 2022 U6 - https://doi.org/10.1016/j.jclepro.2022.135040 SN - 0959-6526 VL - 380 IS - Part 2, Art. Nr.:135040 PB - Elsevier ER - TY - CHAP A1 - Auth, Gunnar A1 - Czarnecki, Christian A1 - Bensberg, Frank A1 - Thor, Andreas ED - Barton, Thomas ED - Müller, Christian ED - Seel, Christian T1 - Digitalisierung des Forschungsprozesses aus Sicht von Forschenden – durch Serviceintegration zum persönlichen Forschungsinformationssystem T2 - Hochschulen in Zeiten der Digitalisierung : Lehre, Forschung und Organisation N2 - In der Diskussion über die Digitalisierung der Forschung spielt die Frage nach der optimalen IT-Unterstützung für Forschende eine wichtige Rolle. Forschende können heute an ihren Hochschulen bzw. Wissenschaftseinrichtungen auf ein breites Angebot interner IT-Dienstleistungen zurückgreifen, das auch kooperative IT-Dienste umfasst, die von mehreren Institutionen in Zusammenarbeit bereitgestellt werden. Außerhalb der eigenen Organisation und des weiteren Verbunds hat sich im Internet zudem ein breites externes Angebot an innovativen, häufig kostenlos nutzbaren Onlinediensten entwickelt. Neben horizontalen Onlinediensten, die sich prinzipiell an jeden Internetnutzer richten (bspw. Dropbox, Twitter, WhatsApp), nimmt auch die Zahl von vertikalen Diensten für wissenschaftliche bzw. Forschungszwecke immer weiter zu (bspw. GoogleScholar, ResearchGate, figshare). Für Forschende eröffnen sich damit vielfältige neue Möglichkeiten, ihren individuellen Forschungsprozess durch digitale Werkzeuge zu verbessern. Aufgrund rechtlicher, technischer und personeller Restriktionen können jedoch interne Dienstleister bei der Identifizierung, Auswahl und Nutzung externer Onlinedienste nur wenig Unterstützung leisten. Aus einer serviceorientierten Perspektive stehen Forschende zunehmend vor dem Problem, wie sich heterogene IT-Dienste interner und externer Anbieter in den eigenen Forschungsprozess integrieren lassen. Als Lösungsansatz skizziert das Kapitel das Konzept eines persönlichen Forschungsinformationssystems nach Gesichtspunkten eines digitalen Servicesystems. KW - Digitalisierung KW - Forschung KW - Forschungsprozess KW - Forschungsinformationssystem KW - Serviceintegration Y1 - 2019 SN - 978-3-658-26617-2 (Print) SN - 978-3-658-26618-9 (Online) U6 - https://doi.org/10.1007/978-3-658-26618-9_17 SP - 287 EP - 307 PB - Springer Vieweg CY - Wiesbaden ER - TY - CHAP A1 - Schneider, Dominik A1 - Wisselink, Frank A1 - Nölle, Nikolai A1 - Czarnecki, Christian ED - Bruhn, Manfred ED - Hadwich, Karsten T1 - Influence of artificial intelligence on commercial interactions in the consumer market T2 - Automatisierung und Personalisierung von Dienstleistungen : Methoden – Potenziale – Einsatzfelder N2 - Recently, novel AI-based services have emerged in the consumer market. AI-based services can affect the way consumers take commercial decisions. Research on the influence of AI on commercial interactions is in its infancy. In this chapter, a framework creating a first overview of the influence of AI on commercial interactions is introduced. This framework summarizes the findings of comparing numerous customer journeys of novel AI-based services with corresponding non-AI equivalents. Y1 - 2020 SN - 978-3-658-30167-5 (Print) SN - 978-3-658-30168-2 (Online) U6 - https://doi.org/10.1007/978-3-658-30168-2_7 SP - 183 EP - 205 PB - Springer Gabler CY - Wiesbaden ER - TY - CHAP A1 - Schneider, Dominik A1 - Wisselink, Frank A1 - Nölle, Nikolai A1 - Czarnecki, Christian ED - Barton, Thomas ED - Müller, Christian T1 - Einfluss von Künstlicher Intelligenz auf Customer Journeys am Beispiel von intelligentem Parken T2 - Künstliche Intelligenz in der Anwendung : Rechtliche Aspekte, Anwendungspotenziale und Einsatzszenarien N2 - Im Konsumentenmarkt entstehen vermehrt neue Anwendungen von Künstlicher Intelligenz (KI). Zunehmend drängen auch Geräte und Dienste in den Markt, die eigenständig über das Internet kommunizieren. Dadurch können diese Geräte und Dienste mit neuartigen KI-basierten Diensten verbessert werden. Solche Dienste können die Art und Weise beeinflussen, wie Kunden kommerzielle Entscheidungen treffen und somit das Kundenerlebnis maßgeblich verändern. Der Einfluss von KI auf kommerzielle Interaktionen wurde bisher noch nicht umfassend untersucht. Basierend auf einem Framework, welches einen ersten Überblick über die Effekte von KI auf kommerzielle Interaktionen gibt, wird in diesem Kapitel der Einfluss von KI auf Customer Journeys am konkreten Anwendungsfall des intelligenten Parkens analysiert. Die daraus gewonnenen Erkenntnisse können in der Praxis als Grundlage genutzt werden, um das Potenzial von KI zu verstehen und bei der Gestaltung eigener Customer Journeys umzusetzen. KW - Kommerzielle Interaktionen KW - Customer Journeys KW - Prozessagilität KW - Customer Experience Management KW - Intelligentes Parken Y1 - 2021 SN - 978-3-658-30935-0 (Print) SN - 978-3-658-30936-7 (Online) U6 - https://doi.org/10.1007/978-3-658-30936-7_7 SP - 99 EP - 122 PB - Springer Vieweg CY - Wiesbaden ER - TY - CHAP A1 - Croon, Philipp A1 - Czarnecki, Christian ED - Czarnecki, Christian ED - Fettke, Peter T1 - Liability for loss or damages caused by RPA T2 - Robotic process automation : Management, technology, applications N2 - Intelligent autonomous software robots replacing human activities and performing administrative processes are reality in today’s corporate world. This includes, for example, decisions about invoice payments, identification of customers for a marketing campaign, and answering customer complaints. What happens if such a software robot causes a damage? Due to the complete absence of human activities, the question is not trivial. It could even happen that no one is liable for a damage towards a third party, which could create an uncalculatable legal risk for business partners. Furthermore, the implementation and operation of those software robots involves various stakeholders, which result in the unsolvable endeavor of identifying the originator of a damage. Overall it is advisable to all involved parties to carefully consider the legal situation. This chapter discusses the liability of software robots from an interdisciplinary perspective. Based on different technical scenarios the legal aspects of liability are discussed. KW - robotic process automation KW - artificial intelligence KW - liability KW - culpability Y1 - 2021 SN - 9783110676778 SN - 9783110676693 SN - 9783110676686 U6 - https://doi.org/10.1515/9783110676693-202 SP - 135 EP - 151 PB - De Gruyter CY - Oldenbourg ER - TY - CHAP A1 - Bensberg, Frank A1 - Auth, Gunnar A1 - Czarnecki, Christian ED - Czarnecki, Christian ED - Fettke, Peter T1 - Finding the perfect RPA match : a criteria-based selection method for RPA solutions T2 - Robotic process automation : Management, technology, applications N2 - The benefits of robotic process automation (RPA) are highly related to the usage of commercial off-the-shelf (COTS) software products that can be easily implemented and customized by business units. But, how to find the best fitting RPA product for a specific situation that creates the expected benefits? This question is related to the general area of software evaluation and selection. In the face of more than 75 RPA products currently on the market, guidance considering those specifics is required. Therefore, this chapter proposes a criteria-based selection method specifically for RPA. The method includes a quantitative evaluation of costs and benefits as well as a qualitative utility analysis based on functional criteria. By using the visualization of financial implications (VOFI) method, an application-oriented structure is provided that opposes the total cost of ownership to the time savings times salary (TSTS). For the utility analysis a detailed list of functional criteria for RPA is offered. The whole method is based on a multi-vocal review of scientific and non-scholarly literature including publications by business practitioners, consultants, and vendors. The application of the method is illustrated by a concrete RPA example. The illustrated structures, templates, and criteria can be directly utilized by practitioners in their real-life RPA implementations. In addition, a normative decision process for selecting RPA alternatives is proposed before the chapter closes with a discussion and outlook. KW - robotic process automation KW - business process automation KW - commercial offthe- shelf solutions KW - software evaluation KW - software selection Y1 - 2021 SN - 978-3-11-067677-8 SN - 978-3-11-067669-3 SN - 9783110676686 U6 - https://doi.org/10.1515/9783110676693-201 SP - 47 EP - 75 PB - De Gruyter CY - Oldenbourg ER - TY - CHAP A1 - Czarnecki, Christian A1 - Fettke, Peter ED - Czarnecki, Christian ED - Fettke, Peter T1 - Robotic process automation : Positioning, structuring, and framing the work T2 - Robotic process automation : Management, technology, applications N2 - Robotic process automation (RPA) has attracted increasing attention in research and practice. This chapter positions, structures, and frames the topic as an introduction to this book. RPA is understood as a broad concept that comprises a variety of concrete solutions. From a management perspective RPA offers an innovative approach for realizing automation potentials, whereas from a technical perspective the implementation based on software products and the impact of artificial intelligence (AI) and machine learning (ML) are relevant. RPA is industry-independent and can be used, for example, in finance, telecommunications, and the public sector. With respect to RPA this chapter discusses definitions, related approaches, a structuring framework, a research framework, and an inside as well as outside architectural view. Furthermore, it provides an overview of the book combined with short summaries of each chapter. KW - Robotic process automation KW - management KW - technology KW - applications KW - research framework Y1 - 2021 SN - 978-3-11-067668-6 (Print) SN - 978-3-11-067669-3 (PDF) SN - 978-3-11-067677-8 (ePub) U6 - https://doi.org/10.1515/9783110676693-202 SP - 3 EP - 24 PB - De Gruyter CY - Oldenbourg ER - TY - CHAP A1 - Czarnecki, Christian A1 - Hong, Chin-Gi A1 - Schmitz, Manfred A1 - Dietze, Christian ED - Urbach, Nils ED - Röglinger, Maximilian ED - Kautz, Karlheinz ED - Alias, Rose Alinda ED - Saunders, Carol ED - Wiener, Martin T1 - Enabling digital transformation through cognitive robotic process automation at Deutsche Telekom Services Europe T2 - Digitalization Cases Vol. 2 : Mastering digital transformation for global business N2 - Subject of this case is Deutsche Telekom Services Europe (DTSE), a service center for administrative processes. Due to the high volume of repetitive tasks (e.g., 100k manual uploads of offer documents into SAP per year), automation was identified as an important strategic target with a high management attention and commitment. DTSE has to work with various backend application systems without any possibility to change those systems. Furthermore, the complexity of administrative processes differed. When it comes to the transfer of unstructured data (e.g., offer documents) to structured data (e.g., MS Excel files), further cognitive technologies were needed. Y1 - 2021 SN - 978-3-030-80002-4 (Print) SN - 978-3-030-80003-1 (Online) U6 - https://doi.org/10.1007/978-3-030-80003-1 SP - 123 EP - 138 PB - Springer CY - Cham ER - TY - THES A1 - Switalla, Justin T1 - Applause : Entwicklung eines Dokumentationssystems für die stationäre Altenpflege - Konzeption einer zukunftsgewandten Dokumentationslösung N2 - Der Personalmangel in der Pflege ist vor allem durch die Pandemie in den Fokus der Öffentlichkeit gerückt. Diese Situation wird sich in den nächsten Jahren aufgrund der steigenden Pflegequote in Folge des demografischen Wandels weiter zuspitzen. Das Dokumentieren der durchgeführten Tätigkeiten nimmt dabei viel Zeit in Anspruch, die nicht den Bewohner:innen zugutekommt. Das Dokumentationssystem „Applause“ soll Pflege- und Betreuungskräfte in ihrer Arbeit unterstützen und durch die einfache Nutzerführung den Schulungsaufwand reduzieren. Durch die Integration von modernen medizinischen Sensoren kann innerhalb des Systems der aktuelle Gesundheitsstatus der Bewohner:innen eingesehen werden. Zusätzlich wird die interne sowie externe Kommunikation innerhalb des Dokumentationssystems abgebildet. Bei Letzterer wird mittels einer datenschutzkonformen Software die auf Fax basierende Kommunikation abgelöst. KW - Pflegekräftemangel KW - Dokumentationssystem KW - Pflegekräfte KW - Gesundheit Y1 - 2022 PB - FH Aachen CY - Aachen ER - TY - JOUR A1 - Czarnecki, Christian A1 - Heuser, Marcus A1 - Krämer, Christian A1 - Stummer, Christoph A1 - Theisinger, Felix A1 - Wettklo, Michael T1 - How to get more customer satisfaction : Erfolg im Wettbewerb durch kundenzentrierte Prozesse JF - Detecon Management Report N2 - Unternehmen sind in der Regel überzeugt, dass sie die Bedürfnisse ihrer Kunden in den Mittelpunkt stellen. Aber in der direkten Interaktion mit dem Kunden zeigen sie häufig Schwächen. Der folgende Beitrag illustriert, wie durch eine konsequente Ausrichtung der Wertschöpfungsprozesse auf die zentralen Kundenbedürfnisse ein Dreifacheffekt erzielt werden kann: Nachhaltig erhöhte Kundenzufriedenheit, gesteigerte Effizienz und eine Differenzierung im Wettbewerb. Y1 - 2006 SN - 1867-3147 IS - 3 SP - 29 EP - 33 PB - Detecon Internat. GmbH CY - Eschborn ER - TY - THES A1 - Theis, Alina Naomi T1 - Nur ein Freitag : Ein Kurzfilm über Verlust und Freundschaft im Schatten des Zweiten Weltkrieges. N2 - Der Film zeigt die wahre Geschichte des 15-jährigen Hans Jokisch, welche auf den Erzählungen seiner jüngeren Schwester, der Zeitzeugin Maria Theis (geb. Jokisch), beruhen. Der Fokus liegt auf der Sichtweise von Kindern und Jugendlichen, einer Generation, die mit dem und im Zweiten Weltkrieg aufgewachsen ist und die gleichzeitig die letzte Generation ist, die uns das Erlebte noch aus erster Hand berichten kann. Hans gelangt mit seiner Familie nach einer harten Flucht vor der Frontlinie zurück in seine Heimat in Schlesien. Doch ihr geliebtes Heim ist besetzt von Familie Schöppe. Sie haben keine Wahl, die beiden Familien müssen sich das Haus von nun an teilen. Im Laufe der Zeit wird das Jokisch Haus auch für Familie Schöppe ein Zuhause und Hans freundet sich mit dem Jungen Bruno Schöppe an. Als Deutschland 1945 kapituliert und Schlesien nun zu Polen gehört, müssen plötzlich beide Familien endgültig das Haus und all ihren Besitz zurücklassen. Hans und Bruno beschließen, die Zwangsenteignung nicht hinzunehmen, doch ihr naiver Plan wird ihnen fast zum Verhängnis. KW - Zeitzeugen KW - historisches Drama KW - zweiter Weltkrieg KW - WW2 KW - Filmproduktion Y1 - 2022 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER - TY - JOUR A1 - Czarnecki, Christian A1 - Geier, Jari A1 - Pflug, Karolin T1 - Netzvirtualisierung durch SDN und NFV : Unternehmensprozesse auf dem Prüfstand JF - LANline N2 - Kundenanforderungen an Netzwerke haben sich in den vergangenen Jahren stark verändert. Mit NFV und SDN sind Unternehmen technisch in der Lage, diesen gerecht zu werden. Die Provider stehen jedoch vor großen Herausforderungen: Insbesondere Produkte und Prozesse müssen angepasst und agiler werden, um die Stärken von NFV und SDN zum Kundenvorteil auszuspielen. Y1 - 2017 SN - 0942-4172 PB - AWI Aktuelles Wissen Verl.-Ges. CY - Trostberg ER - TY - THES A1 - Vasevska, Ivana T1 - FEEL IT_HEAL IT - the process of healing repressed emotions N2 - Unsere Emotionen beeinflussen die Art und Weise, wie wir mit uns selbst und der Welt um uns herum umgehen. Sie wirken sich auf unsere geistige und körperliche Gesundheit aus. Da einige unserer Emotionen als „schlecht“ oder „negativ“ wahrgenommen werden, erlauben wir uns oft nicht, sie zu fühlen, und wir unterdrücken sie. Ziel dieses Projekts ist es, mithilfe von Fotografie und Grafik zu zeigen, wie man mit unangenehmen und so genannten „negativen“ Emotionen umgehen kann. Der Schwerpunkt liegt gleichermaßen auf dem konzeptionellen und kreativen Teil. Dabei wurden ein Modell und wechselnde Farblichter verwendet, um die emotionalen Zustände einer Person darzustellen, die diese Transformation durchläuft. Ein weiteres Ziel ist es, die Bedeutung eines bewussteren Umgangs mit unseren Emotionen zu betonen. Das Endmedium ist ein Fotobuch inkl. Piktogramme, die die fünf Stadien repräsentieren: Leiden, Bewusstsein, Konfrontation, Ausdruck und Akzeptanz. (Suffering, Awareness, Confrontation, Expression and Acceptance). KW - Emotionen KW - Integration KW - Verdrängung KW - Heilung KW - Emotionaler Schmerz Y1 - 2022 PB - FH Aachen CY - Aachen ER - TY - THES A1 - Victoria, Jacqueline T1 - IN BETWEEN : An attempt to capture emotions N2 - Emotionen durchlebt jeder Mensch. Von unserer Geburt bis zu unserem Tod. Der Psychologe Paul Eckman hat sechs grundlegende Emotionen identifiziert. Glück, Traurigkeit, Ekel, Angst, Überraschung und Wut. Emotionen können in positive und negative, aber auch in die weniger beachtete neutrale Emotion unterteilt werden. Emotionen werden ständig und wechselnd erlebt und sind deshalb vorstellbar als "Spektrum" oder als "Unendlichkeitschleife". Wie Menschen Emotionen erfahren, ist unterschiedlich. Sie sind abstrakt. Das Fotobuch "In Between" will das Emotionsspektrum und das Abstrakte mithilfe einer Kurzgeschichte sichtbar machen. Das Editorial und die fotografische Gestaltung greifen das Konzept der endlosen Schleife unserer Gefühlswelt auf und machen sie erlebbar. KW - Fotografie KW - Fotobuch KW - Emotion KW - Endlosschleife KW - Candid Fotografie Y1 - 2022 PB - FH Aachen CY - Aachen ER - TY - THES A1 - vom Endt, Ksenia T1 - MIR : 11 Kinder, 25 Sprachen und eine Welt - Graphic Novel über bilinguale Kinder N2 - Durch die zunehmende Globalisierung und Immigration steigt auch weltweit die Anzahl der Kinder, die mit mehr als einer Sprache aufwachsen. Dies kann für sie in vielerlei Hinsicht wichtig und förderlich sein. In der Graphic Novel „MIR“ wird in zehn Geschichten gezeigt, welche unterschiedlichen Formen von Bilingualismus es gibt, welche Vor- und Nachteile es hat, bilingual aufzuwachsen und wie es sich auf das Alltagsleben der Kinder und der ganzen Familie auswirkt. Die Geschichten sind realen Erlebnissen nachempfunden, die durch Interviews gesammelt wurden und illustrativ dargestellt sind. Mehrsprachigkeit ist weder ein Privileg noch ein Problem. Sprache ist zuallererst Kommunikation, und es ist wichtig, dass sie überhaupt stattfindet. KW - Graphic Novel KW - Illustration KW - Comic KW - Bilingual KW - Kinder Y1 - 2022 PB - FH Aachen CY - Aachen ER - TY - THES A1 - Wojcieszak, Marc David T1 - Da Capo - The Town of Music N2 - In dem Film geht es um die Musikstadt "Da Capo", in der jedes Genre sein eigenes Viertel hat. Unser Protagonist wurde im falschen Viertel geboren und muss sich nun heraus musizieren. KW - Musik KW - Film KW - Stadtviertel KW - Genre KW - musizieren Y1 - 2022 PB - FH Aachen CY - Aachen ER - TY - THES A1 - Wolters, Marina T1 - Zeitfenster : Prototyp einer animierten Installation zum Thema Mesokosmos und Lebensraum Erde N2 - Der Prototyp des Projekts "Zeitfenster" stellt eine Installation dar, inspiriert vom Museum für Naturkunde Berlin. Die Installation besteht aus einer Animation, die an die Fenster des Dinosauriersaals im Museum pojiziert wird. Die Animation zeigt in einer Art Zeitreise, wie das Erbe der Natur aussieht und was der Mensch daraus macht. In der Zeit des Klimawandels setzt sich Design vermehrt für die Aufklärung des Naturschutzes ein. Die Animation soll die Zuschauer, ob Jung oder Alt, für die Verbindung zwischen dem Menschen und der Erde sensibilisieren. Dies wird erreicht, indem sich die Installation die atemberaubende Atmosphäre des Dinosauriersaals zu Nutze macht. Die Fenster des Saals erlauben es, die Bildnisse in beeindruckender Lebensgröße darzustellen. Im Fokus steht, dass der Prototyp ein Erlebnis konzipiert, welches nur durch das Zusammenspiel der verschiedenen Medien möglich ist. KW - Animation KW - Animationsfilm KW - Installation KW - Museum KW - Natur Y1 - 2022 PB - FH Aachen CY - Aachen ER - TY - THES A1 - Wabner, Magnus T1 - Aeroux N2 - Aeroux ist eine Formstudie über die Gestalt einer Luftschiffgondel. Luftschiffe bzw. Zeppeline werden oft mit dem Unglück der Hindenburg in Lakehurst in Verbindung gebracht. Aeroux versucht diese Assoziation zu überwinden und Luftschiffe in der Gegenwart zu verankern. Durch die gezielte, psychologisch inspirierte Gestaltung soll Sicherheit und Ruhe vermittelt werden, sollen spezifische Assoziationen geweckt werden, die weg führen von Bildern vergangener Tage eines brennenden Luftschiffs, um so Zeppeline als klimafreundlichere Alternative zum Flugzeug wieder ins Spiel zu bringen. Aeroux ist ein hybrides Verkehrsmittel, dass in der Lage ist, sowohl Güter als auch Personen in verschiedenen Szenarien zu transportieren. Zeppeline bauchen keine befestigten Landebahnen oder Pisten. Regionen, die über Straßen schwer zugänglich sind, können so in den Warenhandel integriert werden. Gleichermaßen können aber auch Meschen in Regionen befördert werden, die durch Straßen oder Landebahnen nicht oder unzureichend erschlossen sind. Darüber hinaus kann Aeroux ein Ansatz sein die Unverträglichkeit von Fliegen und Klimaschutz aufzulösen. Nicht zuletzt liegt in der gemächlichen Art der Bewegung ein besonderer Zauber. Reisen könnten einen neuen Charakter erhalten: durch die großen Fensterfronten und die geringe Flughöhe können Landschaften auf der Reise neu wahrgenommen werden, der Weg wird wieder Teil des Reisens. Die Arbeit ist in erster Linie eine Auseinandersetzung mit der Form. Wie wirkt Form, wie lassen sich Assoziationen wecken, lenken, leiten. Wie kann technischer Anspruch, gesellschaftliche Bedingung, ökologisches Bewusstsein und nicht zuletzt Genuss in einem Objekt resultieren. Digitale und analoge Fertigung spielen im Zuge der Arbeit ineinander. So entstand das Design der Gondel, nach ersten händischen Skizzen, digital. Das Model der Gondel wurde aus diesen Daten 3D gedruckt und die Darstellung der Traghülle ebenfalls auf Grundlage dieser Daten gelasert. Aeroux möchte Lust auf alternatives Sehen, Denken und Handeln machen. Es gilt viel zu bewegen. KW - Luftschiff KW - Lasern KW - 3D-Druck KW - Renderings KW - Formensprache Y1 - 2022 PB - FH Aachen CY - Aachen ER - TY - THES A1 - Ebner, Nina T1 - Inside Out : a personal visualisation of aphantasia N2 - Das Projekt behandelt die Thematik von Aphantasie, welche die „Abwesenheit freiwilliger, visuell erzeugter Bilder“ (Fußnote) im Kopf beschreibt. Das Ziel der Arbeit ist die Aufklärung und Sensibilisierung Außenstehender. Durch eine reine faktenbasierte Betrachtungsweise ist dies kaum möglich, weshalb ein visueller Ansatz besser geeignet ist. Das Projekt lokalisiert sich in den Bereichen Fotografie & Ausstellung. Die Fotografien stehen für eine beispielhafte Visualisierung der subjektiven Wahrnehmung der Gestalterin – das Ausstellungsobjekt, eine begehbare Camera obscura, repräsentiert das Innere ihres Kopfes. Die Aufnahmen wurden bei Nacht mit verschiedenen Lichtern innerhalb der Camera obscura abgebildet und abgelichtet. Betrachter:innen der Ausarbeitung sollen einen weiteren Blickwinkel auf die Thematik, die Sichtweise und ihre Auswirkungen erhalten – auch im Kontext und der Arbeit als Designer:in. Fußnote: https://www.psychologie.uni-bonn.de/de/unser-institut/abteilungen/differentielle-biologische-psychologie/%20%20Aphantasia%20Research%20Project%20Bonn%20 KW - Aphantasie KW - Visualisierung KW - Abwesenheit KW - Camera Obscura KW - Wahrnehmung Y1 - 2022 PB - FH Aachen CY - Aachen ER - TY - THES A1 - Kannengießer, Justine T1 - Vom Airbag zum Rucksack mit Upcycling : Kampagne zur Steigerung der Bekanntheit der Marke Airpaq N2 - In der Automobilindustrie entsteht ein enormes Ausmaß an Abfall. Genau an dieser Stelle greift das Kölner Start-up Airpaq ein, das nachhaltige Rucksäcke und Accessoires aus Autoschrott unter fairen Arbeitsbedingungen in der EU herstellt. Das Ziel der Kampagne ist es, die Markenbekanntheit zu steigern und eine tiefergreifende und lang anhaltende Verbindung zur jungen Zielgruppe aufzubauen. Genau so, wie Airpaq den Taschen-Markt revolutioniert, stellt auch die junge Zielgruppe immer wieder Altbewährtes infrage. Mit der „HOLYSCRAP“-Bewegung ruft die Kampagne Upcycling-Abenteuer ins Leben. Die Kampagne ermutigt dazu, Teil der Upcycling-Community zu werden, um immer wieder neu und anders "schrottastische" Erlebnisse zu entdecken. So soll eingeladen werden, nicht nur beim Griff zur Tasche mal etwas Neues auszuprobieren, sondern auch bei allen gemeinsamen Aktivitäten, die man mit Airpaq erlebt. KW - Airpaq KW - Automobilbranche KW - nachhaltig KW - Kampagne KW - Rucksack Y1 - 2022 PB - FH Aachen CY - Aachen ER - TY - JOUR T1 - Dimensionen 1-2021: Magazin der FH Aachen University of Applied Sciences - 50 Jahre FH Aachen N2 - 04| Adieda & Welkomme 06| Das WIR wird großgeschrieben 08| Hoch aus dem Norden, da komm ich her! 12| „Ich möchte ein Heimatgefühl erzeugen“ 14| Das neue Rektorat – persönlich und privat 18| „Wir müssen uns einen Kompass geben“ 20| Keime im Wasser 22| „Ist mitgemeint auch wirklich mitgedacht?“ 24| Wachs für den Weltraum 28| Auslandssemester trotz Pandemie 30| Virtuelles Reinschnuppern 31| Top-Platzierungen für die FH 32| Luftstrom 36| Gründen will gelehrt sein 38| „Lebende Plastikkugel“ 40| Pioniere des 21. Jahrhunderts 43| Wir bleiben in Kontakt 44| Auszeit 46| Hand in Hand ins All 48| Kampf gegen tödliche Infektionen 50| Ein Bau für den Holzbau 52| Wissen ist Silber. Machen ist Gold. 60| Honorarprofessur für Dr. Roger Uhle 61| Faktoren ohne Null T3 - Dimensionen - Magazin der FH Aachen University of Applied Sciences - 2021, 1 Y1 - 2021 CY - Aachen ER - TY - JOUR T1 - Dimensionen 1-2020: Magazin der FH Aachen University of Applied Sciences - Bibliotheken im 21. Jahrhundert N2 - 04| Wissen stirbt nicht aus 12| Mathe ist sexy! 15| „Bei Grün bitte mit Abstand eintreten“ 16| Maschinenbau — mehr als nur Metall 17| Brasilianischer Doktorand der zweiten Generation 18| Aus Alt mach Neu 20| Virtuelle Verleihung 21| Ehrenvolle Auszeichnung 22| Mit Regenjacke und Gummistiefeln 24| Ein Herz aus Beton 27| Wissenstransfer für die Automobilindustrie 28| Mission zum Mond 30| Eine Brücke, die sich selbst überwacht 32| Licht an — Kanal frei 34| Ein Tropfen auf den heißen Stein 36| Ist ein Studium das Richtige für mich? 38| Himmelblau und Feuerrot 41| Kopfnuss 41| Impressum 42| Mit Leichtigkeit und Transparenz 46| Dialektik des Stillstands T3 - Dimensionen - Magazin der FH Aachen University of Applied Sciences - 2020, 1 Y1 - 2020 CY - Aachen ER - TY - JOUR T1 - Dimensionen 2-2019: Magazin der FH Aachen University of Applied Sciences - Namibia auf dem Weg in die Zukunft N2 - 06| Namibia auf der Suche nach dem Weg in die Zukunft 16| Dort arbeiten, wo andere an Urlaub denken 19| „Das macht unsere Qualität aus“ 20| Sicher auf See 24| Nachhaltig im All 26| Viel Kaffee in New York 29| Wo man Digitalisierung studieren kann 30| „Ein Leben reicht nicht aus“ 32| 3022 Kilometer durch Australien 36| Für die Zeit nach der Kohle 38| Der Taktgeber 40| Die Emsigen 44| Volle Kraft voraus 46| Einmal in der Zeit zurück 50| Exkursion in die Wolken 56| Echte Gefühle in virtuellen Welten 58| Wir sind FH 60| Mit Herz und Hand 61| Kopfnuss 62| Nachruf 63| Impressum T3 - Dimensionen - Magazin der FH Aachen University of Applied Sciences - 2019, 2 Y1 - 2019 CY - Aachen ER - TY - CHAP A1 - Czarnecki, Christian A1 - Bensberg, Frank T1 - Enhanced Telecom Operations Map (eTOM) T2 - Enzyklopädie der Wirtschaftsinformatik Y1 - 2019 N1 - Online-Lexikon SP - 1 EP - 4 PB - Gito CY - Berlin ER - TY - CHAP A1 - Czarnecki, Christian T1 - Robotergesteuerte Prozessautomatisierung T2 - Enzyklopädie der Wirtschaftsinformatik T2 - Robotic Process Automation (RPA) Y1 - 2019 N1 - Online-Lexikon SP - 1 EP - 3 PB - Gito CY - Berlin ER - TY - CHAP A1 - Czarnecki, Christian A1 - Bensberg, Frank T1 - Telekommunikationsunternehmen, Anwendungssysteme für T2 - Enzyklopädie der Wirtschaftsinformatik Y1 - 2019 N1 - Online-Lexikon SP - 1 EP - 3 PB - Gito CY - Berlin ER - TY - JOUR A1 - Bensberg, Frank A1 - Auth, Gunnar A1 - Czarnecki, Christian ED - Haake, Jörg M. T1 - Literaturanalyse mit Text Mining JF - E-Learning and Education (eleed) N2 - Die Durchführung einer systematischen Literaturrecherche ist eine zentrale Kompetenz wissenschaftlichen Arbeitens und bildet daher einen festen Ausbildungsbestandteil von Bachelor- und Masterstudiengängen. In entsprechenden Lehrveranstaltungen werden Studierende zwar mit den grundlegenden Hilfsmitteln zur Suche und Verwaltung von Literatur vertraut gemacht, allerdings werden die Potenziale textanalytischer Methoden und Anwendungssysteme (Text Mining, Text Analytics) dabei zumeist nicht abgedeckt. Folglich werden Datenkompetenzen, die zur systemgestützten Analyse und Erschließung von Literaturdaten erforderlich sind, nicht hinreichend ausgeprägt. Um diese Kompetenzlücke zu adressieren, ist an der Hochschule Osnabrück eine Lehrveranstaltung konzipiert und projektorientiert umgesetzt worden, die sich insbesondere an Studierende wirtschaftswissenschaftlicher Studiengänge richtet. Dieser Beitrag dokumentiert die fachliche sowie technische Ausgestaltung dieser Veranstaltung und zeigt Potenziale für die künftige Weiterentwicklung auf. KW - E-Learning KW - Text Mining KW - Text Analytics KW - Literaturrecherche KW - Literaturanalyse Y1 - 2020 SN - 1860-7470 N1 - Volltext, nur online IS - 13 SP - 1 EP - 13 PB - FernUniversität in Hagen CY - Hagen ER - TY - JOUR A1 - Czarnecki, Christian T1 - Buchbesprechung : Anwendungsorientierte Wirtschaftsinformatik - Strategische Planung, Entwicklung und Nutzung von Informationssystemen JF - Anwendungen und Konzepte der Wirtschaftsinformatik (AKWI-Journal) Y1 - 2020 U6 - https://doi.org/10.26034/lu.akwi.2020.3264 SN - 2296-4592 N1 - Das besprochene Buch ist im Katalog Plus als E-Book zu finden. Eine ältere Auflage steht im Regal unter der Grundsignatur 21 QGT 55 SP - 101 EP - 101 PB - Technische Hochschule Wildau CY - Wildau ER - TY - JOUR T1 - Dimensionen 1-2022: Magazin der FH Aachen University of Applied Sciences - Auf dem Weg zur Nachhaltigkeit N2 - Inhaltsverzeichnis: 06| "WIR" werden nachhaltig 10| Der Kraft-Stoff aus dem Bioreaktor 14| Energieverbrauch des Campus Jülich optimieren 16| „Eine große Hilfestellung für Flutopfer“ 20| Von der ersten Skizze zu den Blumen in der Vase 22|Wie schläft es sich im All, Herr Maurer? 24| Expedition Arktis 28| Eine Frage, zwei Antworten 30| Der schönste Arbeitsplatz der Welt 32| Im Einklang 36| Ein Vorgeschmack auf die echte Arbeitswelt 38| Den Rätseln des Universums auf der Spur 40| Auf Umwegen in die Spitzenforschung 42| Klappe FH Aachen, die erste … Kamera läuft! 44| Auszeit 46| „Fotografie öffnet Türen zu Parallelwelten“ 50| Es gibt viel zu tun 52| Durch-Blick 54| Weichen stellen für einen ganz besonderen Job 58| Souta, Iver und der Wind 60| Die FH Aachen ist systemakkreditiert 61| Der Vulkan 62| Kopfnuss, Impressum T3 - Dimensionen - Magazin der FH Aachen University of Applied Sciences - 2022, 1 Y1 - 2022 CY - Aachen ER - TY - CHAP A1 - Fissabre, Anke ED - Dux, Holger A. T1 - Ein Entwurf für die Umnutzung der Bauten des jüdischen Friedhofs an der Lütticher Straße T2 - Der jüdische Friedhof Aachen Lütticher Straße Aachen Y1 - 2022 SN - 978-3-87519-266-7 SP - 71 EP - 74 PB - Mayersche Buchhandlung Aachen GmbH CY - Aachen ER - TY - CHAP A1 - Fissabre, Anke ED - Dux, Holger A. T1 - Die Bauten des jüdischen Friedhofs an der Lütticher Straße T2 - Der Jüdische Friedhof Aachen Y1 - 2022 SN - 978-3-87519-266-7 SP - 51 EP - 69 PB - Mayersche Buchhandlung Aachen GmbH CY - Aachen ER - TY - JOUR A1 - Hörenbaum, Christoph A1 - Laumann, Jörg A1 - Prokop, Ines T1 - Zur Anwendung des Eurocode 3 Teil 1-2 für die Heißbemessung und Anregungen für dessen Novellierung JF - Stahlbau N2 - Die Eurocodes werden bis zum Jahr 2020 im Europäischen Komitee für Normung (CEN), Technisches Komitee TC 250, überarbeitet. In Vorbereitung auf die Eurocode-Novellierung haben engagierte Ingenieure im Rahmen der Initiative PraxisRegeln Bau (PRB) die für die praktische Anwendung häufig genutzten Teile des Eurocode 3 untersucht. Mit dem Ziel, die Praxistauglichkeit des Eurocode 3 für die Heißbemessung zu verbessern, wurden die bestehende Norm EN 1993 Teil 1-2 insbesondere in Bezug auf die Anwenderfreundlichkeit analysiert und Vorschläge für die europäische Novellierung erarbeitet. Die Analysen zeigen, dass durch Umstrukturierungen und durch die Einführung von Tabellen die Verständlichkeit und Anwenderfreundlichkeit der Regeln für die Heißbemessung bedeutend erhöht werden können. KW - EN 1993-1-2 KW - Tragwerksbemessung KW - Brandfall KW - Forschung, pränormativ KW - structural design Y1 - 2016 U6 - https://doi.org/10.1002/stab.201610382 SN - 1437-1049 VL - 85 IS - 6 SP - 429 EP - 434 PB - Ernst & Sohn GmbH CY - Berlin ER - TY - RPRT A1 - Geißler, Karsten A1 - Prokop, Ines A1 - Bubner, André A1 - Egner, Ralf A1 - Heyde, Stefan A1 - Kempkes, Marian A1 - Kühn, Bertram A1 - Laumann, Jörg A1 - Lieberwirth, Peter A1 - Naumes, Johannes A1 - Ruga, Julija A1 - Schilling, Sivo A1 - Schmidt, Herbert A1 - Ummenhofer, Thomas T1 - Verbesserung der Praxistauglichkeit der Baunormen durch pränormative Arbeit – Teilantrag 3: Stahlbau, Abschlussbericht Y1 - 2015 SN - 978-3-8167-9539-1 PB - Fraunhofer IRB Verlag CY - Stuttgart ER - TY - BOOK A1 - Laumann, Jörg A1 - Feldmann, Markus A1 - Frickel, Jörg A1 - Krahwinkel, Manuel A1 - Kraus, Matthias A1 - Stranghöner, Natalie A1 - Ummenhofer, Thomas T1 - Petersen Stahlbau : Grundlagen der Berechnung und baulichen Ausbildung von Stahlbauten N2 - Die Theorie und Konstruktion der wichtigsten Bereiche der Stahlbautechnik werden von den Grundlagen her entwickelt und durch viele Beispiele praxisbezogen erläutert. Das Buch ist aus Vorlesungen im Grund- und Vertiefungsstudium des Bauingenieurwesens entstanden. Der Inhalt wird zum Teil systematisch, zum Teil exemplarisch dargestellt. Für Konstrukteure und Statiker in den technischen Büros, der Beratenden Ingenieure und der Prüfämter enthält das Buch aufbereitete Berechnungsverfahren und Konstruktionsvorschläge in großer Zahl. KW - Behälterbau KW - Bemessung KW - Brandschutz KW - Brückenbau KW - Festigkeitslehre Y1 - 2022 SN - 978-3-658-20510-2 U6 - https://doi.org/10.1007/978-3-658-20510-2 PB - Springer Vieweg CY - Wiesbaden ET - 5. Auflage ER - TY - JOUR A1 - Kindmann, Rolf A1 - Kraus, Matthias A1 - Laumann, Jörg A1 - Vette, Jan T1 - Verallgemeinerte Berechnungsmethode für in Beton eingespannte Stahlprofile – Einspanntiefen, Tragfähigkeitsnachweise und Bemessungshilfen JF - Stahlbau N2 - Stützen und Träger aus Stahlprofilen können in Fundamente oder Wände aus Stahlbeton einbetoniert werden. Diese Anschlüsse wirken in der Regel wie Einspannungen, die eine ausreichende Einspanntiefe erfordern. Im Folgenden wird eine verallgemeinerte Berechnungsmethode für in Stahlbetonkonstruktionen eingespannte Stahlprofile aus gewalzten I-Profilen, geschweißten I-Profilen, runden Hohlprofilen, eckigen Hohlprofilen und einzelligen Kastenquerschnitten vorgestellt. Für Beanspruchungen infolge einachsiger Biegung um die starke und schwache Profilachse werden der profilabhängige Ansatz der Betondruckspannungen im Einspannbereich und die Ermittlung der Einspanntiefe behandelt. Unter Berücksichtigung der Normalkraft werden an den maßgebenden Stellen Tragfähigkeitsnachweise für die Stahlprofile geführt. Als Ergänzung zu den Berechnungsformeln werden Bemessungshilfen zur Verfügung gestellt, die die Wahl der mitwirkenden Breiten und der Einspanntiefen erleichtert. KW - Stahlprofile KW - Anschlüsse an Stahlbeton KW - Einspanntiefen KW - Eingespannte Stützen und Träger KW - steel profiles Y1 - 2022 U6 - https://doi.org/10.1002/stab.202200024 SN - 1437-1049 VL - 93 IS - Early View SP - 1 EP - 25 PB - Ernst & Sohn GmbH CY - Berlin ER - TY - JOUR A1 - Emig, J. A1 - Hebel, Christoph A1 - Schwark, A. T1 - Einsatzbereiche für Verkehrsnachfragemodelle JF - Straßenverkehrstechnik N2 - In der Praxis bestehen vielfältige Einsatzbereiche für Verkehrsnachfragemodelle. Mit ihnen können Kenngrößen des Verkehrsangebots und der Verkehrsnachfrage für den heutigen Zustand wie auch für zukünftige Zustände bereitgestellt werden, um so die Grundlagen für verkehrsplanerische Entscheidungen zu liefern. Die neuen „Empfehlungen zum Einsatz von Verkehrsnachfragemodellen für den Personenverkehr“ (EVNM-PV) (FGSV 2022) veranschaulichen anhand von typischen Planungsaufgaben, welche differenzierten Anforderungen daraus für die Modellkonzeption und -erstellung resultieren. Vor dem Hintergrund der konkreten Aufgabenstellung sowie deren spezifischer planerischer Anforderungen bildet die abzuleitende Modellspezifikation die verabredete Grundlage zwischen Auftraggeber und Modellersteller für die konkrete inhaltliche, fachliche Ausgestaltung des Verkehrsmodells. Y1 - 2022 U6 - https://doi.org/10.53184/SVT10-2022-2 SN - 0039-2219 VL - 66 IS - 10 SP - 727 EP - 736 PB - Kirschbaum Verlag GmbH CY - Bonn ER - TY - JOUR A1 - Hahn, Geogr W. A1 - Hebel, Christoph A1 - Manz, W. T1 - Die neuen Empfehlungen für Verkehrsnachfragemodellierung im Personenverkehr JF - Straßenverkehrstechnik N2 - Die neu erschienenen „Empfehlungen zum Einsatz von Verkehrsnachfragemodellen für den Personenverkehr“ liefern erstmals als Empfehlungspapier der Forschungsgesellschaft für Straßen- und Verkehrswesen einen umfassenden Überblick zu den verschiedenen Aspekten der Modellierung und geben dem Fachplaner konkrete Hilfestellung für die Konzeption von Nachfragemodellen. Das Empfehlungspapier zielt unter anderem darauf ab, die Erwartungen und das Anspruchsniveau in Hinblick auf Sachgerechtigkeit der Modelle, die erzielbare Modellqualität und den Detaillierungsgrad der Modellaussagen zu harmonisieren. Y1 - 2022 U6 - https://doi.org/10.53184/SVT10-2022-1 SN - 0039-2219 VL - 66 IS - 10 SP - 721 EP - 726 PB - Kirschbaum Verlag GmbH CY - Bonn ER - TY - THES A1 - Nelles, Charlene T1 - Brain Hack N2 - Protagonistin des Films ist Cassandra Becker, eine 25-jährige Informatikstudentin und Mitglied der Hackerorganisation PFABW (Progress For a Better World). Sie hat es sich zum Ziel gesetzt, die Welt zu einem besseren Ort zu machen. Sie legt sich allerdings mit den falschen Leuten an und wird für die Verbreitung eines zerstörerischen Computervirus verantwortlich gemacht, der gesundheitliche Folgen für den Menschen mit sich bringt. Sie und ihr bester Freund Jake Fischer haben bei einem PFABW-Mitglied Zuflucht gefunden. Dort versuchen sie gemeinsam herauszufinden, was es mit dem mysteriösen Virus auf sich hat. KW - Freundschaft KW - Schuld KW - Liebe KW - IT KW - Hacker Y1 - 2022 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER - TY - THES A1 - Schiffers, Simon T1 - Historische Stoffe im Spielfilm : Zwischen Authentizität und Unterhaltung N2 - Historische Stoffe im Spielfilm Zwischen Authentizität und Unterhaltung Spielfilme über wahre Begebenheiten stellen sich der Herausforderung, historisch korrekte Darstellung mit einer spannenden und sehenswerten Präsentation zu kombinieren. Dies ist ein schwieriger Balance Akt, gerade bei Studentenprojekten mit geringem Budget. Im Kurzfilm über Julius Erasmus, dem „Totengräber von Vossenack“, wurde sich dieser Aufgabe gestellt. Inhaltlich werden seine möglichen Beweggründe dargestellt, die ihn dazu brachten kurz nach dem 2. Weltkrieg zahlreiche gefallene Soldaten im ehemaligen Kampfgebiet im Hürtgenwald zu begraben. Die schriftliche Dokumentation des Projektes zeigt die Recherche des verfilmten Stoffes, Herausforderungen während der Produktion, sowie persönliche Eindrücke und Lerneffekte. Letztendlich ist ein Werk entstanden, dass respektvoll mit der zu Grunde liegenden Geschichte umgeht und gleichsam ein cineastisches Erlebnis für den Zuschauer darstellt. KW - Kurzfilm KW - Authentizität KW - wahre Begebenheit KW - Vossenack KW - Julius Erasmus Y1 - 2022 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER - TY - THES A1 - Treutlein, Antonia T1 - Entwicklung eines Erscheinungsbildes für die Meeresschutzorganisation Ocean Care N2 - Ocean Care ist eine politisch unabhängige Non-Profit-Organisation mit Sitz in der Schweiz. Sie setzt sich seit 1989 für den Schutz von Meeressäugern und deren Lebensraum ein. Seit 2011 ist Ocean Care außerdem UN-Sonderberaterin für Fragen im Meeresschutz. Da Ocean Care die Öffentlichkeit für das Thema Meeresschutz sensibilisieren möchte und ihre Arbeit durch Spenden finanziert wird, ist ein professionelles, vertrauenerweckendes Erscheinungsbild unerlässlich. Durch ein zeitgemäßes und seriöses Design, welches sich von anderen Organisationen abhebt, kann die Zielgruppe erweitert und die Bedeutsamkeit der Arbeit hervorgehoben werden. Das neue Erscheinungsbild beruht auf der Idee, dass sich die Informationen unter der Meeresoberfläche befinden. Die Linie, die den Meeresspiegel visualisiert, dient außerdem medienübergreifend als Orientierungshilfe. KW - Erscheinungsbild KW - Gestaltung KW - Corporate Design KW - Layout KW - Redesign Y1 - 2022 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER - TY - THES A1 - Wetzlar, Jana T1 - Vielgut Festival 2022 : Etablierung eines neuen Musikfestivals in Aachen N2 - Endlich! Nach über zwei Jahren kulturellen Stillstands richtet der Musiknetzwerk Aachen e.V. ein Festival aus. Die Bachelorandin Jana Wetzlar übernimmt hierbei die Veranstaltungsplanung und -bewerbung. Der erste Teil der Arbeit umfasst die Erarbeitung eines einzigartigen Festivalkonzepts, bei dem die Förderung von jungen Newcomerkünstler:innen und die ökologische Nachhaltigkeit der Veranstaltung im Vordergrund stehen. Eine weitere Besonderheit stellt das paritätisch besetzte Künstler:innen-Line-Up dar. Im zweiten Teil der Arbeit wurden eine umfangreiche Werbekampagne sowie ein passendes Corporate Design entwickelt, die die Besonderheiten des Festivals hervorheben und viele Festivalbesucher:innen generieren sollen. Die übergeordneten Ziele der Arbeit bestehen darin, einen Beitrag zur gesellschaftlichen Etablierung des Musiknetzwerk Aachen e.V. zu leisten und die Voraussetzungen für ein jährlich wiederkehrendes Festival zu schaffen. KW - Festival KW - Musik KW - Veranstaltung KW - Kampagne KW - Marketing Y1 - 2022 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER - TY - THES A1 - Wolf, Nina T1 - Koexistieren : Die Stufen der Mensch-Tier-Beziehung – Vom Nutztier bis zum Personenrecht N2 - Seit 2002 ist der Tierschutz fest im Grundgesetz verankert, jedoch herrscht immer noch ein enormes Ungleichgewicht bei der letztendlichen Durchsetzung gegenüber der Tiernutzungsinteressen. Die Nichteinhaltung des Tierschutzes stellt nicht nur aus Tierwohlsicht, sondern auch aus Klimaschutzgründen eine ernst zu nehmende Problematik dar, welche wir nur gemeinsam angehen können. Die Gesellschaft sollte sich über das eigene Konsumverhalten bewusst werden, gleichermaßen müssen auch überzeugende Alternativen aufgezeigt werden. Thematisch ist die Arbeit in drei Teile gegliedert. Die Geschichte, das Recht der Tiere und die Zukunftsaussichten stehen hier im Fokus. Wichtig ist es, den Istzustand neutral darzustellen, um die Fakten nicht zu harmonisieren. Die Publikation soll nicht abschrecken, vielmehr soll sie die Leser:innen motivieren, Dinge ändern zu wollen. Denn nur miteinander können wir friedlich „koexistieren“. KW - Koexistenz KW - Tierschutz KW - Nutztier KW - Kultur KW - Gesellschaft Y1 - 2022 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER - TY - THES A1 - Inceman Cremer, Suzan T1 - Kouyou : Ort im Raum N2 - Selbstliebe, der Moment der Ruhe, sich eine mentale Pause erlauben und von allem bewusst abzuschalten, sind aktuelle Themen unserer Gesellschaft. Die Zeit, in der wir leben, bewegt sich in einer Geschwindigkeit, die alle unsere Sinne überlastet und uns nicht mehr erlaubt, selbst zuzuhören oder volle Momente der Ruhe zu erleben. Thema der Bachelorarbeit ist der Entwurf eines Sitzmöbels, welches inspiriert ist durch die sakralische Architektur. Der Stuhl soll das Gefühl von Umformung und Leichtigkeit vermitteln. Er ist aus Eiche gebaut und unterstützt den Menschen in seiner bewussten Sitzhaltung. Die Eiche ist ein Baum, der für Kraft, Durchhaltevermögen und Gerechtigkeit steht. Es heißt auch, wenn man eine Eiche sieht, sie umarmen soll, da sie heilende Kräfte hat. Hier ist aber die Eiche, die den Menschen symbolisch umarmen soll, wenn man auf ihr sitzt. Und somit spielen Architektur, Möbel und der Mensch eine spielende Rolle, und zwar ist es die menschliche Haltung im Raum. KW - Philosophie KW - Architektur KW - Möbel KW - Reise KW - Eiche Y1 - 2022 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER - TY - THES A1 - Vogt, Lena T1 - Archäologischer Restaurator : Ausstellungskonzept Römisch-Germanisches Museum Köln N2 - Alte, geschichtsrelevante und thematisch angeordnete Objekte, welche man in den Vitrinen der Museen betrachten kann, das kennt sicher jeder. Doch wie kommen diese Artefakte eigentlich in die Vitrinen? Welche Menschen sind dafür verantwortlich, dass wir diese Kulturgüter bestaunen können? In diesem temporären Ausstellungskonzept für das Römisch-Germanische Museum Köln geht es darum, die sonst verborgene Arbeit der Restauratoren des Museums für die Besucher:innen sichtbar zu machen, ihnen genauere Einblicke in die Arbeit mit ihren Anforderungen zu geben und Restaurierungsprozesse auf zu zeigen. Diese Arbeit demonstriert, wie es abseits der Öffentlichkeit aussieht und wer dafür verantwortlich ist, dass wir einen Einblick in die vergangenen Zeit erhalten können. Das Projekt zeigt eine mögliche Bespielung des Museums, wie das Berufsbild der Restauratoren in die Dauerausstellung integriert werden könnte. KW - Ausstellungsdesign KW - Fotografie KW - Museumsdesign KW - Restauratoren KW - Restaurierung Y1 - 2022 PB - FH Aachen CY - Aachen ER - TY - THES A1 - Janssen, Hanna T1 - UMGARNT : Handarbeit als Mittel zur Festigung der emotionalen Bindung zu Möbelstücken N2 - Nach drei Jahren ist der Anblick der beigen Kommode doch etwas langweilig geworden und es steht ein Tapetenwechsel an? Das ist noch lange kein Grund, neue Möbel kaufen zu müssen. Mit dem „BOBBI“-Regal lässt sich das Farbkonzept des Möbelstücks fortlaufend anpassen. Das reduzierte Grundgestell basiert auf einem einfachen Stecksystem und ermöglicht nicht nur einen schnellen, intuitiven Aufbau, sondern auch eine modulare Erweiterung des Regalsystems. Eintönig? Nein Danke! Zeitloses, langlebiges Design muss nicht schlicht und farblos sein! Der Schlüssel liegt in der Individualisierbarkeit. Mithilfe einer einfachen textilen Bespannungstechnik passt der Kunde das Gerüst nach seinen Vorstellungen an. Auf diese Weise kann der Charakter des Möbelstücks nicht nur farblich, sondern auch strukturell regelmäßig verändert werden und trägt zu einer nachhaltigen und achtsamen Raumgestaltung bei. KW - Möbeldesign KW - Textil KW - Individualisierbarkeit KW - Achtsamkeit KW - Weben Y1 - 2022 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER - TY - THES A1 - Trinidad Avila, Maria Alejandra T1 - Work Habitat : Modular-skalierbare Office Markenstrategie für rasant wachsende Startups N2 - „Work Habitat“ ist eine markenorientierte Officelösung, die auf skalierbare Weise mit einem Start-up mitwächst und in Kooperation mit dem Unternehmen academa GmbH entstanden ist. Diese Brand Experience fördert Teambuilding und Identifikation mit dem Unternehmen. Sie passt sich an die Teammitglieder an, indem sie einen ganzheitlichen Blick auf das Office-System bewahrt. Ferner stellt sie eine nahtlose Verbindung digitaler und analoger Arbeitswelten dar und bietet eine einladende Umgebung verschiedener Arten zu Arbeiten an: von Deep-Focus bis zur kooperativen Zusammenarbeit und der Anregung zwangloser Begegnungen. Die modularen Komponenten können trotz Veränderungen, Umzügen oder unerwartet rasanten Entwicklungen nachhaltig und flexibel eingesetzt werden. Eine schnelllebige Welt erfordert eine angebrachte, sich ihr anpassende New-Work-Umgebung. KW - office design KW - spatial design KW - interior design KW - New York KW - Markenstrategie Y1 - 2022 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER - TY - THES A1 - Voth, Emily T1 - KiWA : Die Garderobe für kleine Selbstständige N2 - Kindertagesstätten bieten Kleinkindern den Zugang zu unbeschwertem und spielerischem Lernen. Was also, wenn schon der Eingangsbereich die Reizüberflutung bereit hält, der Stauraum der Entfaltung der Kinder nicht gerecht wird und ihre Eigenständigkeit ungefördert bleibt? Es kommt zu unzufriedenen Kindern und Frustration aller Beteilligten. "KIWA" ist das Garderobensystem für Kinder zur Stärkung der heranwachsenden Selbstständigkeit. Mithilfe von persönlichen Wiedererkennungsmerkmalen wird Eigenverantwortung geschult. Leicht und sicher zu erreichender Stauraum sorgt für Ordnung. Spielerisches lernen trotz Ordnung. KW - Kindermöbel KW - Kindergarten KW - Möbeldesign KW - Ordnung KW - Kleinkinder Y1 - 2022 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER - TY - THES A1 - Horvath, Nicolas T1 - Neues Corporate Design für das Rautenstrauch Joest Museum Köln N2 - Der Mensch in seinen Welten – das Konzept des Rautenstrauch Joest Museums verfolgt den Ansatz des Kulturvergleichs und strebt im Zuge dessen die Betonung der Ebenbürtigkeit aller Kulturen an. Die Sammlung unterteilt sich nicht – wie gewohnt – anhand geografischer Gesichtspunkte, sondern behandelt Themen, die Menschen auf der ganzen Welt beschäftigen. Das in dieser Arbeit gestaltete neue Erscheinungsbild greift den veränderten gesellschaftlichen Stellenwert von ethnologischen Museen auf und positioniert das Museum als aktiven Diskussionsteilnehmer im Zuge des Postkolonialismus. Das entwickelte Key-Visual aus eigener Schrift, einheitlicher Rastersystematik und prägnantem Farbkonzept gibt einen Einblick darin, wie Menschen früher probiert haben, ihre Welt zu verstehen und sie zu erschließen. KW - Markengestaltung KW - Museum KW - Redesign KW - Postkolonialismus KW - Kunst Y1 - 2022 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER - TY - THES A1 - Toma, Paul T1 - Scriptum : Geochronologische Darstellung der Schriftentstehung vom 33. Jh. v. Chr. bis heute N2 - Scriptum ist ein Interface mit Installationscharakter, welches die geschichtliche Entstehung von Schriftsystemen aus einer geochronologischen Perspektive darstellt. Die Installation wurde hauptsächlich für Museumsausstellungen konzipiert und besteht aus einer Wandprojektion, die durch iPads im Raum von mehreren Nutzern gleichzeitig gesteuert werden kann. Auf der Projektion sind alle 145 von Noto Sans unterstützten Schriftsysteme zu finden, die nach ihrer örtlichen Entstehung auf einer Weltkarte platziert wurden. Die Arbeit beruht auf dem wissenschaftlichen Datensatz aus dem Projekt „The World’s Writing Systems“ aufrufbar unter www.worldswritingsystems.org. Neben dem Informierungszweck dient die Installation auch als ein Ausrufezeichen für die Idee, dass Schrift ein wichtiger Aspekt unseres Kulturerbes ist und als ein Spiegel für die Evolution der Menschheit betrachtet werden kann. KW - Geschichte KW - Schriftsysteme KW - Typographie KW - Interaktiv KW - Interfacedesign Y1 - 2022 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER - TY - THES A1 - Meesters, Elena T1 - Gestaltung eines häuslichen Telemonitoringsystems zur Prognose kardialer Dekompensation N2 - Herzinsuffizienz ist eine der häufigsten Herzerkrankungen in Deutschland. Sie ist fortschreitend und nicht heilbar. Der Krankheitsverlauf ist geprägt von plötzlichen, z.T. lebensbedrohlichen Verschlechterungen und Krankenhauseinweisungen, nach denen die Leistung des Herzen vermindert bleibt. Diese Dekompensationen lassen sich bisher im heimischen Umfeld nicht durch Messwerte vorhersehen. Dieses Gerät bestimmt die Flüssigkeitsansammlungen in der Lunge, die ein mittelfristiges Symptom einer Dekompensation sind. Außerdem misst es über einen Hautsensor die im Schweiß enthaltene Menge eines Proteins, das bei Überdehnung des Herzmuskels vermehrt im Blutplasma zu finden ist. So können Dekompensationen bis zu zwei Wochen vor einem akuten Ereignis detektiert und behandelt werden. Außerdem gibt es tagesformabhängige Tipps für die Alltagsgestaltung mit der Erkrankung. KW - Herzinusffizienz KW - Medizin KW - Herz KW - Gesundheit KW - Telemonitoring Y1 - 2022 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER - TY - THES A1 - Czarnecki, Christian T1 - Entwicklung einer referenzmodellbasierten Unternehmensarchitektur für die Telekommunikationsindustrie N2 - Die Telekommunikationsindustrie hat in den letzten Jahrzehnten einen enormen Wandel vollzogen. Für Telekommunikationsunternehmen erfordert dies fundamentale Umstrukturierungen von Strategie, Prozessen, Anwendungssystemen und Netzwerktechnologien. Dabei spielen Unternehmensarchitekturen und Referenzmodelle eine wichtige Rolle. Zwar existieren in der Praxis anerkannte Referenzmodelle, aber wie sind diese für eine systematische Transformation zu gestalten? Wie sieht eine konkrete Lösung für die Telekommunikationsindustrie aus? Als Antwort stellt Christian Czarnecki in seinem Buch eine referenzmodellbasierte Unternehmensarchitektur vor. Basierend auf einer umfangreichen Untersuchung von Transformationsprojekten werden Probleme und Anforderungen der Praxis identifiziert, für die mit Methoden der Unternehmenstransformation, Referenzmodellierung und Unternehmensarchitektur ein Lösungsvorschlag entwickelt und evaluiert wird. Dieser besteht u. a. aus detaillierten Anwendungsfällen, Referenzprozessabläufen, einer Zuordnung von Prozessen zu Anwendungssystemen sowie Handlungsempfehlungen zur Virtualisierung. Für Wissenschaftler und Studierende der Wirtschaftsinformatik zeigt das Buch neue Erkenntnisse einer anwendungsorientierten Referenzmodellierung. Für Praktiker liefert es eine methodisch fundierte Lösung für die aktuellen Transformationsbedarfe der Telekommunikationsindustrie. Christian Czarnecki arbeitet seit 2004 als Unternehmensberater und hat viele Telekommunikationsunternehmen bei deren Transformation begleitet. In 2013 erfolgte die Promotion zum Doktoringenieur an der Otto-von-Guericke-Universität Magdeburg. KW - Referenzmodelle KW - Unternehmensstrukturen KW - Management Y1 - 2013 SN - 9783832535100 PB - Logos CY - Berlin ER - TY - BOOK A1 - Czarnecki, Christian A1 - Dietze, Christian T1 - Reference architecture for the telecommunications industry: Transformation of strategy, organization, processes, data, and applications N2 - This book reflects the tremendous changes in the telecommunications industry in the course of the past few decades – shorter innovation cycles, stiffer competition and new communication products. It analyzes the transformation of processes, applications and network technologies that are now expected to take place under enormous time pressure. The International Telecommunication Union (ITU) and the TM Forum have provided reference solutions that are broadly recognized and used throughout the value chain of the telecommunications industry, and which can be considered the de facto standard. The book describes how these reference solutions can be used in a practical context: it presents the latest insights into their development, highlights lessons learned from numerous international projects and combines them with well-founded research results in enterprise architecture management and reference modeling. The complete architectural transformation is explained, from the planning and set-up stage to the implementation. Featuring a wealth of examples and illustrations, the book offers a valuable resource for telecommunication professionals, enterprise architects and project managers alike. KW - Enterprise architecture KW - Enterprise transformation KW - Reference modelling KW - TM Forum KW - Telecommunication Y1 - 2017 SN - 978-3-319-46755-9 (Print) SN - 978-3-319-83578-5 (Print) SN - 978-3-319-46757-3 (PDF) U6 - https://doi.org/10.1007/978-3-319-46757-3 PB - Springer CY - Cham ER - TY - CHAP A1 - Czarnecki, Christian A1 - Heuser, Marcus A1 - Spiliopoulou, Myra ED - Irani, Zahir T1 - How does the implementation of a next generation network influence a telecommunication company? T2 - European and Mediterranean Conference on Information Systems N2 - As the potential of a Next Generation Network (NGN) is recognized, telecommunication companies consider switching to it. Although the implementation of an NGN seems to be merely a modification of the network infrastructure, it may trigger or require changes in the whole company and even influence the company strategy. To capture the effects of NGN we propose a framework based on concepts of business engineering and technical recommendations for the introduction of NGN technology. The specific design of solutions for the layers "Strategy", "Processes" and "Information Systems" as well as their interdependencies are an essential characteristic of the developed framework. We have per-formed a case study on NGN implementation and observed that all layers captured by our framework are influenced by the introduction of an NGN. KW - Next Generation Network KW - Business Engineering KW - Telecommunication Y1 - 2009 SN - 9781902316697 N1 - European and Mediterranean Conference on Information Systems 2009 (EMCIS2009), July 13-14, 2009, Crowne Plaza Hotel, Izmir SP - 1 EP - 11 PB - Brunel University CY - London ER - TY - CHAP A1 - Czarnecki, Christian ED - Eymann, Torsten T1 - Gestaltung von Customer Relationship Management über die Grenzen von Telekommunikationsunternehmen hinweg T2 - Tagungsband zum Doctoral Consortium der WI 2009 N2 - Durch die Fragmentierung von Wertschöpfungsketten ergeben sich neue Herausforderungen für das Management von Kundenbeziehungen. Die Dissertation untersucht die daraus resultierenden Anforderungen an eine übergreifende Integration von Customer Relationship Management in der Telekommunikationsindustrie. Ziel ist es, durch Anwendung von Methoden eines Enterprise Architecture Framework eine übergreifend Lösung zu gestalten. Grundlegende Prämisse dabei ist, dass die übergreifende Gestaltung eines Customer Relationship Management für alle an der Wertschöpfung beteiligten Unternehmen vorteilhaft ist. Y1 - 2011 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:703-opus-5462 SN - 1864-9300 SP - 11 EP - 23 PB - Universität Bayreuth Lehrstuhl für Wirtschaftsinformatik CY - Bayreuth ER - TY - CHAP A1 - Czarnecki, Christian A1 - Winkelmann, Axel A1 - Spiliopoulou, Myra ED - Pokorny, Jaroslav ED - Repa, Vaclav ED - Richta, Karel ED - Wojtkowski, Wita ED - Linger, Henry ED - Barry, Chris ED - Lang, Michael T1 - Making business systems in the telecommunication industry more customer-oriented T2 - Information Systems Development : Business Systems and Services: Modeling and Development N2 - Market changes have forced telecommunication companies to transform their business. Increased competition, short innovation cycles, changed usage patterns, increased customer expectations and cost reduction are the main drivers. Our objective is to analyze to what extend transformation projects have improved the orientation towards the end-customers. Therefore, we selected 38 real-life case studies that are dealing with customer orientation. Our analysis is based on a telecommunication-specific framework that aligns strategy, business processes and information systems. The result of our analysis shows the following: transformation projects that aim to improve the customer orientation are combined with clear goals on costs and revenue of the enterprise. These projects are usually directly linked to the customer touch points, but also to the development and provisioning of products. Furthermore, the analysis shows that customer orientation is not the sole trigger for transformation. There is no one-fits-all solution; rather, improved customer orientation needs aligned changes of business processes as well as information systems related to different parts of the company. KW - Business Process KW - Customer Orientation KW - Enterprise Architecture KW - Transformation Project KW - Telecommunication Industry Y1 - 2011 SN - 978-1-4419-9645-9 (Print) SN - 978-1-4419-9790-6 (Online) U6 - https://doi.org/10.1007/978-1-4419-9790-6_14 N1 - 19th International Conference on Information Systems Development held in Prague, Czech Republic, August 25 - 27, 2010. SP - 169 EP - 180 PB - Springer CY - New York ER - TY - CHAP A1 - Czarnecki, Christian A1 - Winkelmann, Axel A1 - Spiliopoulou, Myra ED - Mattfeld, Dirk Christian ED - Robra-Bissantz, Susanne T1 - Transformation in Telecommunication – Analyse und Clustering von Real-life Projekten T2 - Multikonferenz Wirtschaftsinformatik 2012 N2 - Die Veränderungen des Telekommunikationsmarktes haben in der Praxis zu einer Vielzahl von Transformationsprojekten geführt. Was gehört aber zu einem “Transformationsprojekt”, welche Prozesse und Systeme werden verändert? Zur Beantwortung dieser Frage haben wir 184 Berichte zu Projekten analysiert, die als "Transformationsprojekte" bezeichnet waren. Für die Analyse haben wir einen Kodierungsrahmen konzipiert und anhand dessen die Berichte mit einem hierarchischen Clustering-Verfahren in Themen gruppiert. Die Ergebnisse liefern Hinweise über die in der Praxis gesetzten Schwerpunkte und Prioritäten. Sie können somit als Unterstützung für Unternehmen dienen, die ein Transformationsprojekt planen. Sie weisen zudem darauf hin, in welchen Bereichen eines Unternehmens Unterstützung durch wissenschaftlich erprobte Werkzeuge und Modelle nötig ist. Y1 - 2012 SN - 9783942183635 N1 - MKWI 2012 : Multikonferenz Wirtschaftsinformatik, 29.02.2012-02.03.2012, Braunschweig SP - 985 EP - 998 PB - Gito CY - Berlin ER - TY - CHAP A1 - Nursinski-Stolberg, André A1 - Gangatharan, Kiritharan A1 - Czarnecki, Christian ED - Mayr, Heinrich C. ED - Pinzger, Martin T1 - Development of a subject-oriented reference process model for the telecommunications industry T2 - GI Edition Proceedings Band 259 INFORMATIK 2016 N2 - Generally the usage of reference models can be structured top-down or bottom-up. The practical need of agile change and flexible organizational implementation requires a consistent mapping to an operational level. In this context, well-established reference process models are typically structured top-down. The subject-oriented Business Process Management (sBPM) offers a modeling concept that is structured bottom-up and concentrates on the process actors on an operational level. This paper applies sBPM to the enhanced Telecom Operations Map (eTOM), a well-accepted reference process model in the telecommunications industry. The resulting design artifact is a concrete example for a combination of a bottom-up and top-down developed reference model. The results are evaluated and confirmed in practical context through the involvement of the industry body TMForum. KW - Subject-oriented Business Process Management KW - Reference Process Model KW - eTOM KW - Telecommunications Industry. Y1 - 2016 SN - 9783885796534 SN - 1617-5468 N1 - 26.-30. September 2016, Klagenfurt. SP - 699 EP - 712 PB - Gesellschaft für Informatik e.V. CY - Bonn ER - TY - CHAP A1 - Czarnecki, Christian ED - Mayr, Heinrich C. ED - Pinzger, Martin ED - Gesellschaft für Informatik e. V. (GI), T1 - Design und Nutzung einer industriespezifischen Referenzarchitektur für die Telekommunikationsindustrie T2 - GI Edition Proceedings Band 259 INFORMATIK 2016. 26.-30. September 2016 Klagenfurt N2 - Zur Unterstützung des Transformationsbedarfs von Telekommunikationsunternehmen sind die Referenzmodelle des TM Forums in der Praxis weltweit anerkannt. Dabei findet jedoch meist eine losgelöste Nutzung für spezifische Einzelthemen statt. Daher führt dieser Artikel die bestehenden Inhalte in einer industriespezifischen, übergreifenden Referenzarchitektur zusammen. Der Fokus liegt auf den Ebenen Aufbauorganisation, Prozesse, Applikationen und Daten. Darüber hinaus werden inhaltliche Architekturdomänen zur Strukturierung angeboten. Die Referenzarchitektur ist hierarchisch aufgebaut und wird hier beispielhaft für ausgewählte, aggregierte Inhalte beschrieben. Als erste Evaluation wird die Anwendung der Referenzarchitektur in drei Praxisprojekten erläutert. KW - Referenzmodellierung KW - Unternehmensarchitektur KW - Unternehmenstransformation KW - TM Forum KW - enhanced Telecom Operations Map (eTOM) Y1 - 2016 SN - 9783885796534 SN - 1617-5468 SP - 807 EP - 814 PB - Köllen CY - Bonn ER - TY - CHAP A1 - Czarnecki, Christian A1 - Dietze, Christian ED - Maedche, Alexander ED - vom Brocke, Jan ED - Hevner, Alan T1 - Domain-Specific reference modeling in the telecommunications industry T2 - DESRIST 2017: Designing the Digital Transformation N2 - The telecommunications industry is currently going through a major transformation. In this context, the enhanced Telecom Operations Map (eTOM) is a domain-specific process reference model that is offered by the industry organization TM Forum. In practice, eTOM is well accepted and confirmed as de facto standard. It provides process definitions and process flows on different levels of detail. This article discusses the reference modeling of eTOM, i.e., the design, the resulting artifact, and its evaluation based on three project cases. The application of eTOM in three projects illustrates the design approach and concrete models on strategic and operational levels. The article follows the Design Science Research (DSR) paradigm. It contributes with concrete design artifacts to the transformational needs of the telecommunications industry and offers lessons-learned from a general DSR perspective. KW - enhanced Telecom Operations Map (eTOM) KW - Process reference model KW - Process design KW - Map (eTOM) Process reference model Process design Telecommunications industry Y1 - 2017 SN - 978-3-319-59144-5 SN - 978-3-319-59143-8 U6 - https://doi.org/10.1007/978-3-319-59144-5_19 N1 - Designing the Digital Transformation 12th International Conference, DESRIST 2017, Karlsruhe, Germany, May 30 - June 1, 2017. SP - 313 EP - 329 PB - Springer CY - Cham ER - TY - CHAP A1 - Schneider, Dominik A1 - Wisselink, Frank A1 - Czarnecki, Christian ED - Barton, Thomas ED - Herrmann, Frank ED - Meister, Vera G. ED - Müller, Christian ED - Seel, Christian T1 - Qualitative Wertschöpfungsanalyse von Anwendungsfällen des Narrowband Internet of Things T2 - Prozesse, Technologie, Anwendungen, Systeme und Management 2017. Angewandte Forschung in der Wirtschaftsinformatik N2 - Primäre Ziele des Internets der Dinge sind die Steuerung physischer Gegenstände aus der Distanz und das Erfassen von Informationen aus dem Umfeld dieser Gegenstände. Dazu werden Hardwarekomponenten in Gegenstände des täglichen Lebens und die Umwelt integriert. Mithilfe von Informations- und Kommunikationstechnologien entsteht hieraus das Internet der Dinge (Internet of Things, IoT). Vor einem Jahr wurde mit Narrowband Internet of Things (NB-IoT) eine Technologie die es ermöglicht, Hardwarekomponenten energieeffizient und unmittelbar über das Mobilfunknetz zu vernetzen. Gegenstände werden dadurch über große Reichweiten eigenständig kommunikationsfähig. Das IoT steht mit NB-IoT vor einem gestiegenen Nutzenpotenzial, da eine zunehmende Anzahl miteinander verbundener Gegenstände und der Austausch größerer Datenmengen realisierbar sind. Damit sind aus wirtschaftlicher Sicht neue, innovative Anwendungsfälle des IoT möglich, die auch bereits in der Praxis diskutiert werden. In diesem Beitrag wird anhand eines konkreten Anwendungsfalls untersucht, welche neuen Geschäfts- bzw. Partnermodelle durch die gemeinsame Nutzung von NB-IoT-Daten und Big Data-Technologien entstehen und welcher qualitative Mehrwert für die an einem Anwendungsfall beteiligten Stakeholder geschaffen wird. Dazu wird – einem konstruktionsorientierten Forschungsansatz folgend – ein Bewertungsrahmen zur qualitativen Wertschöpfungsanalyse von NB-IoT entwickelt, der u.a. auf der Schablone nach Cockburn und dem Business Model Canvas basiert. Anhand dieses Bewertungsrahmens wird ein Anwendungsfall untersucht, der in anonymisierter Form an konkrete Praxisprojekte angelehnt ist. Konkret wird ein Anwendungsfall betrachtet, der einen Fahrradverleih 2.0 basierend auf dem Einsatz von NB-IoT vorschlägt. Aus den Untersuchungsergebnissen gehen beispielsweise Erkenntnisse hervor, wie Geschäftsmodelle auf Y1 - 2017 SN - 978-3-944330-56-3 N1 - Tagungsband zur 30. AKWI-Jahrestagung vom 17.09.2017 bis 20.09.2017 an der Hochschule Aschaffenburg SP - 184 EP - 193 PB - mana-Buch CY - Heide ER - TY - CHAP A1 - Thomé, Tristan Eberhard A1 - Czarnecki, Christian A1 - Auth, Gunnar A1 - Bensberg, Frank ED - Barton, Thomas ED - Herrmann, Frank ED - Meister, Vera G. ED - Müller, Christian ED - Seel, Christian T1 - Erweiterung des Referenzprozessmodells eTOM um die Anforderungen des deutschen IT-Sicherheitsgesetzes T2 - Prozesse, Technologie, Anwendungen, Systeme und Management 2017. Angewandte Forschung in der Wirtschaftsinformatik N2 - Kritische Infrastrukturen sind primäre Ziele krimineller Hacker. Der Deutsche Bundestag reagierte darauf am 25. Juli 2015 mit einem Gesetz zur Verbesserung der Sicherheit von ITSystemen, dem IT-Sicherheitsgesetz. Dies verlangt von Betreibern kritischer Infrastrukturen, angemessene Mindeststandards für organisatorische und technische Sicherheit zu implementieren, um den Betrieb und die Verfügbarkeit dieser Infrastruktur zu gewährleisten. Telekommunikationsunternehmen sind einerseits von diesem Gesetz in besonderem Maße betroffen und verfügen andererseits mit dem Rahmenwerk enhanced Telecom Operations Map (eTOM) über ein international anerkanntes Referenzmodell zur Gestaltung von Geschäftsprozessen in dieser Branche. Da sämtliche Telekommunikationsunternehmen in Deutschland verpflichtet sind, das Gesetz innerhalb eines bestimmten Zeitrahmens zu implementieren, präsentiert dieser Beitrag einen Vorschlag zur Erweiterung von eTOM um die relevanten Anforderungen des deutschen IT-Sicherheitsgesetzes. Y1 - 2017 SN - 978-3-944330-56-3 N1 - Tagungsband zur 30. AKWI-Jahrestagung vom 17.09.2017 bis 20.09.2017 an der Hochschule Aschaffenburg SP - 51 EP - 60 PB - mana-Buch CY - Heide ER - TY - CHAP A1 - Schnejider, Dominik A1 - Wisselink, Frank A1 - Czarnecki, Christian ED - Eibl, Maximilian ED - Gaedke, Martin ED - Gesellschaft für Informatik e. V. (GI), T1 - Transformation von Wertschöpfungsketten durch das Internet der Dinge – Bewertungsrahmen und Fallstudie T2 - GI Edition Proceedings Band 275 INFORMATIK 2017 N2 - Momentan finden in vielen Branchen umfassende Veränderungen von Märkten und Wertschöpfungsketten statt, welche auch als Digitale Transformation bezeichnet werden. In diesem Zusammenhang wird das Internet der Dinge (Internet of Things, IoT) als ein wichtiger technischer Enabler der Veränderungen angesehen. Primäre Ziele des IoT sind die Steuerung physischer Gegen-stände aus der Distanz und das Erfassen von Informationen aus dem Umfeld dieser Gegenstände. Welche neuen Geschäfts-bzw. Partnermodelle entstehen durch die gemeinsame Nutzung von IoT-Daten und Big-Data-Technologien und welcher qualitative Mehrwert wird dadurch geschaffen? Als Antwort wird in diesem Beitrag ein Bewertungsrahmen zur qualitativen Wertschöpfungsanalyse von IoT vorgeschlagen. Anhand dieses Bewertungsrahmens wird ein Anwendungsfall untersucht, der in anonymisierter Form an konkrete Praxisprojekte angelehnt ist. Konkret wird ein Anwendungsfall betrachtet, der eine Abfallwirtschaft 2.0 basierend auf dem Einsatz von IoT vorschlägt. Aus den Untersuchungsergebnissen gehen beispielsweise Erkenntnisse hervor, wie Geschäftsmodelle auf Basis eines unentgeltlichen Informationsaustauschs durch IoT gestaltet werden können. KW - Digitale Transformation KW - Unternehmensarchitekturen KW - Unternehmensarchitekturen Internet der Dinge KW - Geschäftsmodelle KW - Wertschöpfungskettenanalyse Y1 - 2017 SN - 978-3-88579-669-5 U6 - https://doi.org/10.18420/in2017_208 SN - 1617-5468 N1 - Unternehmensarchitektur in Forschung und Praxis, Chemnitz, 25.-29. September 2017 SP - 2081 EP - 2094 PB - Köllen CY - Bonn ER - TY - JOUR A1 - Czarnecki, Christian A1 - Winkelmann, Axel A1 - Spiliopoulou, Myra T1 - Services in electronic telecommunication markets: a framework for planning the virtualization of processes JF - Electronic Markets N2 - The potential of electronic markets in enabling innovative product bundles through flexible and sustainable partnerships is not yet fully exploited in the telecommunication industry. One reason is that bundling requires seamless de-assembling and re-assembling of business processes, whilst processes in telecommunication companies are often product-dependent and hard to virtualize. We propose a framework for the planning of the virtualization of processes, intended to assist the decision maker in prioritizing the processes to be virtualized: (a) we transfer the virtualization pre-requisites stated by the Process Virtualization Theory in the context of customer-oriented processes in the telecommunication industry and assess their importance in this context, (b) we derive IT-oriented requirements for the removal of virtualization barriers and highlight their demand on changes at different levels of the organization. We present a first evaluation of our approach in a case study and report on lessons learned and further steps to be performed. KW - Telecommunication KW - Services KW - Process virtualization KW - Product bundling KW - Transformation Y1 - 2010 U6 - https://doi.org/10.1007/s12525-010-0045-8 SN - 1422-8890 VL - 20 IS - 3-4 SP - 197 EP - 207 PB - Springer CY - Berlin ER - TY - JOUR A1 - Czarnecki, Christian A1 - Spiliopoulou, Myra T1 - A holistic framework for the implementation of a next generation network JF - International Journal of Business Information Systems N2 - As the potential of a next generation network (NGN) is recognised, telecommunication companies consider switching to it. Although the implementation of an NGN seems to be merely a modification of the network infrastructure, it may trigger or require changes in the whole company, because it builds upon the separation between service and transport, a flexible bundling of services to products and the streamlining of the IT infrastructure. We propose a holistic framework, structured into the layers ‘strategy’, ‘processes’ and ‘information systems’ and incorporate into each layer all concepts necessary for the implementation of an NGN, as well as the alignment of these concepts. As a first proof-of-concept for our framework we have performed a case study on the introduction of NGN in a large telecommunication company; we show that our framework captures all topics that are affected by an NGN implementation. KW - next generation network KW - telecommunication KW - NGN KW - IP-based networks KW - product bundling Y1 - 2012 U6 - https://doi.org/10.1504/IJBIS.2012.046291 SN - 1746-0972 VL - 9 IS - 4 SP - 385 EP - 401 PB - Inderscience Enterprises CY - Olney, Bucks ER - TY - JOUR A1 - Czarnecki, Christian A1 - Winkelmann, Axel A1 - Spiliopoulou, Myra T1 - Referenzprozessabläufe für Telekommunikationsunternehmen: Eine Erweiterung des eTOM-Modells JF - Wirtschaftsinformatik N2 - Der Telekommunikationsmarkt erfährt substanzielle Veränderungen. Neue Geschäftsmodelle, innovative Dienstleistungen und Technologien erfordern Reengineering, Transformation und Prozessstandardisierung. Mit der Enhanced Telecom Operation Map (eTOM) bietet das TM Forum ein international anerkanntes de facto Referenz-Prozess-Framework basierend auf spezifischen Anforderungen und Ausprägungen der Telekommunikationsindustrie an. Allerdings enthält dieses Referenz-Framework nur eine hierarchische Sammlung von Prozessen auf unterschiedlichen Abstraktionsebenen. Eine Kontrollsicht verstanden als sequenzielle Anordnung von Aktivitäten und daraus resultierend ein realer Prozessablauf fehlt ebenso wie eine Ende-zu-Ende-Sicht auf den Kunden. In diesem Artikel erweitern wir das eTOM-Referenzmodell durch Referenzprozessabläufe, in welchen wir das Wissen über Prozesse in Telekommunikationsunternehmen abstrahieren und generalisieren. Durch die Referenzprozessabläufe werden Unternehmen bei dem strukturierten und transparenten (Re-)Design ihrer Prozesse unterstützt. Wir demonstrieren die Anwendbarkeit und Nützlichkeit unserer Referenzprozessabläufe in zwei Fallstudien und evaluieren diese anhand von Kriterien für die Bewertung von Referenzmodellen. Die Referenzprozessabläufe wurden vom TM Forum in den Standard aufgenommen und als Teil von eTOM Version 9 veröffentlicht. Darüber hinaus diskutieren wir die Komponenten unseres Ansatzes, die auch außerhalb der Telekommunikationsindustrie angewandt werden können. KW - Prozessstandardisierung KW - Prozessabläufe KW - Prozessmodellierung KW - Referenzmodellierung KW - eTOM Y1 - 2013 U6 - https://doi.org/10.1007/s11576-013-0351-9 SN - 1861-8936 VL - 55 IS - 2 SP - 83 EP - 97 PB - Springer Fachmedien CY - Wiesbaden ER - TY - JOUR A1 - Bensberg, Frank A1 - Auth, Gunnar A1 - Czarnecki, Christian T1 - Einsatz von Text Analytics zur Unterstützung literaturintensiver Forschungsprozesse: Konzeption, Realisierung und Lessons Learned JF - Anwendungen und Konzepte der Wirtschaftsinformatik N2 - Das anhaltende Wachstum wissenschaftlicher Veröffentlichungen wirft die Fragestellung auf, wie Literaturana-lysen im Rahmen von Forschungsprozessen digitalisiert und somit produktiver realisiert werden können. Insbesondere in informationstechnischen Fachgebieten ist die Forschungspraxis durch ein rasant wachsendes Publikationsaufkommen gekennzeichnet. Infolgedessen bietet sich der Einsatz von Methoden der Textanalyse (Text Analytics) an, die Textdaten automatisch vorbereiten und verarbeiten können. Erkenntnisse entstehen dabei aus Analysen von Wortarten und Subgruppen, Korrelations- sowie Zeitreihenanalysen. Dieser Beitrag stellt die Konzeption und Realisierung eines Prototypen vor, mit dem Anwender bibliographische Daten aus der etablierten Literaturdatenbank EBSCO Discovery Service mithilfe textanalytischer Methoden erschließen können. Der Prototyp basiert auf dem Analysesystem IBM Watson Explorer, das Hochschulen lizenzkostenfrei zur Verfügung steht. Potenzielle Adressaten des Prototypen sind Forschungseinrichtungen, Beratungsunternehmen sowie Entscheidungsträger in Politik und Unternehmenspraxis. KW - Text Analytics KW - Literaturanalyse KW - Forschungsprozess KW - EBSCO Discovery Service KW - IBM Watson Explorer Y1 - 2018 U6 - https://doi.org/10.26034/lu.akwi.2018.3221 SN - 2296-4592 VL - 2018 IS - 8 SP - 1 EP - 6 PB - AKWI CY - Luzern ER - TY - JOUR A1 - Czarnecki, Christian A1 - Bensberg, Frank A1 - Auth, Gunnar T1 - Die Rolle von Softwarerobotern für die zukünftige Arbeitswelt JF - HMD Praxis der Wirtschaftsinformatik N2 - Im Rahmen der Digitalisierung ist die zunehmende Automatisierung von bisher manuellen Prozessschritten ein Aspekt, der massive Auswirkungen auf die zukünftige Arbeitswelt haben wird. In diesem Kontext werden an den Einsatz von Softwarerobotern zur Prozessautomatisierung hohe Erwartungen geknüpft. Bei den Implementierungsansätzen wird die Diskussion aktuell insbesondere durch Robotic Process Automation (RPA) und Chatbots geprägt. Beide Ansätze verfolgen das gemeinsame Ziel einer 1:1-Automatisierung von menschlichen Handlungen und dadurch ein direktes Ersetzen von Mitarbeitern durch Maschinen. Bei RPA werden Prozesse durch Softwareroboter erlernt und automatisiert ausgeführt. Dabei emulieren RPA-Roboter die Eingaben auf der bestehenden Präsentationsschicht, so dass keine Änderungen an vorhandenen Anwendungssystemen notwendig sind. Am Markt werden bereits unterschiedliche RPA-Lösungen als Softwareprodukte angeboten. Durch Chatbots werden Ein- und Ausgaben von Anwendungssystemen über natürliche Sprache realisiert. Dadurch ist die Automatisierung von unternehmensexterner Kommunikation (z. B. mit Kunden) aber auch von unternehmensinternen Assistenztätigkeiten möglich. Der Beitrag diskutiert die Auswirkungen von Softwarerobotern auf die Arbeitswelt anhand von Anwendungsbeispielen und erläutert die unternehmensindividuelle Entscheidung über den Einsatz von Softwarerobotern anhand von Effektivitäts- und Effizienzzielen. KW - Robotic Process Automation KW - Chatbots KW - Prozessautomatisierung KW - Arbeit 4.0 KW - Digitalisierung Y1 - 2019 U6 - https://doi.org/10.1365/s40702-019-00548-z SN - 2198-2775 VL - 56 IS - 4 SP - 795 EP - 808 PB - Springer CY - Cham ER - TY - CHAP A1 - Bensberg, Frank A1 - Auth, Gunnar A1 - Czarnecki, Christian ED - Hofmann, Georg Rainer ED - Alm, Wolfgang T1 - Unterstützung von Wissenstransferprozessen durch Erschließung von Literaturdatenbanken - ein gestaltungsorientierter Ansatz auf Basis von Text Analytics T2 - Wissenstransfer in der Wirtschaftsinformatik Fachgespräch im Rahmen der MKWI 2018 N2 - Angesichts des anhaltenden Wachstums wissenschaftlicher Veröffentlichungen werden Instrumente benötigt, um Literaturanalysen durch Digitalisierung produktiver zu gestalten. Dieser Beitrag stellt einen Ansatz vor, der bibliographische Daten aus der Literaturdatenbank EBSCO Discovery Service mithilfe von Text-Analytics-Methoden erschließt. Die Lösung basiert auf dem Textanalysesystem IBM Watson Explorer und eignet sich für explorative Literaturanalysen, um beispielsweise den Status quo emergierender Technologiefelder in der Literatur zu reflektieren. Die generierten Ergebnisse sind in den Kontext der zunehmenden Werkzeugunterstützung des Literaturrechercheprozesses einzuordnen und können für intra- sowie interinstitutionelle Wissenstransferprozesse in Forschungs- und Beratungskontexten genutzt werden. KW - Wissenstransfer KW - Text Analytics KW - Literaturdaten KW - Literaturanalyse KW - Literatur-analyse-prozess Y1 - 2018 SN - 9783981844207 N1 - MKWI 2018: Multikonferenz Wirtschaftsinformatik 2018 in Lüneburg, 06.03.2018-09.03.2018 SP - 6 EP - 15 PB - IMI-Verlag ; Hochschule Aschaffenburg, Information Management Institut CY - Aschaffenburg ER - TY - JOUR A1 - Czarnecki, Christian A1 - Dietze, Christian T1 - Gestaltungsorientierte Forschung am Beispiel der Referenzmodellierung in der Telekommunikationsindustrie JF - HMD Praxis der Wirtschaftsinformatik N2 - Am Beispiel der Telekommunikationsindustrie zeigt der Beitrag eine konkrete Ausgestaltung anwendungsorientierter Forschung, die sowohl für die Praxis als auch für die Wissenschaft nutzen- und erkenntnisbringend ist. Forschungsgegenstand sind die Referenzmodelle des Industriegremiums TM Forum, die von vielen Telekommunikationsunternehmen zur Transformation ihrer Strukturen und Systeme genutzt werden. Es wird die langjährige Forschungstätigkeit bei der Weiterentwicklung und Anwendung dieser Referenzmodelle beschrieben. Dabei wird ein konsequent gestaltungsorientierter Forschungsansatz verfolgt. Das Zusammenspiel aus kontinuierlicher Weiterentwicklung in Zusammenarbeit mit einem Industriegremium und der Anwendung in vielfältigen Praxisprojekten führt zu einer erfolgreichen Symbiose aus praktischer Nutzengenerierung sowie wissenschaftlichem Erkenntnisgewinn. Der Beitrag stellt den gewählten Forschungsansatz anhand konkreter Beispiele vor. Darauf basierend werden Empfehlungen und Herausforderungen für eine gestaltungs- und praxisorientierte Forschung diskutiert. KW - Design Science Research KW - Anwendungsorientierter Forschungsansatz KW - Praxisprojekte KW - Referenzmodellierung KW - Enhanced Telecom Operations Map Y1 - 2020 U6 - https://doi.org/10.1365/s40702-020-00594-y SN - 2198-2775 VL - 57 IS - 2 SP - 310 EP - 323 PB - Springer Nature CY - Cham ER - TY - JOUR A1 - Burger, René A1 - Rumpf, Jessica A1 - Do, Xuan Tung A1 - Monakhova, Yulia A1 - Diehl, Bernd W. K. A1 - Rehahn, Matthias A1 - Schulze, Margit T1 - Is NMR combined with multivariate regression applicable for the molecular weight determination of randomly cross-linked polymers such as lignin? JF - ACS Omega N2 - The molecular weight properties of lignins are one of the key elements that need to be analyzed for a successful industrial application of these promising biopolymers. In this study, the use of 1H NMR as well as diffusion-ordered spectroscopy (DOSY NMR), combined with multivariate regression methods, was investigated for the determination of the molecular weight (Mw and Mn) and the polydispersity of organosolv lignins (n = 53, Miscanthus x giganteus, Paulownia tomentosa, and Silphium perfoliatum). The suitability of the models was demonstrated by cross validation (CV) as well as by an independent validation set of samples from different biomass origins (beech wood and wheat straw). CV errors of ca. 7–9 and 14–16% were achieved for all parameters with the models from the 1H NMR spectra and the DOSY NMR data, respectively. The prediction errors for the validation samples were in a similar range for the partial least squares model from the 1H NMR data and for a multiple linear regression using the DOSY NMR data. The results indicate the usefulness of NMR measurements combined with multivariate regression methods as a potential alternative to more time-consuming methods such as gel permeation chromatography. Y1 - 2021 U6 - https://doi.org/10.1021/acsomega.1c03574 SN - 2470-1343 VL - 6 IS - 44 SP - 29516 EP - 29524 PB - ACS Publications CY - Washington, DC ER - TY - JOUR A1 - Monakhova, Yulia A1 - Diehl, Bernd W. K. T1 - Simplification of NMR Workflows by Standardization Using 2H Integral of Deuterated Solvent as Applied to Aloe vera Preparations JF - Applied Magnetic Resonance N2 - In this study, a recently proposed NMR standardization approach by 2H integral of deuterated solvent for quantitative multicomponent analysis of complex mixtures is presented. As a proof of principle, the existing NMR routine for the analysis of Aloe vera products was modified. Instead of using absolute integrals of targeted compounds and internal standard (nicotinamide) from 1H-NMR spectra, quantification was performed based on the ratio of a particular 1H-NMR compound integral and 2H-NMR signal of deuterated solvent D2O. Validation characteristics (linearity, repeatability, accuracy) were evaluated and the results showed that the method has the same precision as internal standardization in case of multicomponent screening. Moreover, a dehydration process by freeze drying is not necessary for the new routine. Now, our NMR profiling of A. vera products needs only limited sample preparation and data processing. The new standardization methodology provides an appealing alternative for multicomponent NMR screening. In general, this novel approach, using standardization by 2H integral, benefits from reduced sample preparation steps and uncertainties, and is recommended in different application areas (purity determination, forensics, pharmaceutical analysis, etc.). Y1 - 2021 U6 - https://doi.org/10.1007/s00723-021-01393-4 SN - 1613-7507 VL - 52 IS - 11 SP - 1591 EP - 1600 PB - Springer CY - Cham ER - TY - JOUR A1 - Burmistrova, Natalia A. A1 - Soboleva, Polina M. A1 - Monakhova, Yulia T1 - Is infrared spectroscopy combined with multivariate analysis a promising tool for heparin authentication? JF - Journal of Pharmaceutical and Biomedical Analysis N2 - The investigation of the possibility to determine various characteristics of powder heparin (n = 115) was carried out with infrared spectroscopy. The evaluation of heparin samples included several parameters such as purity grade, distributing company, animal source as well as heparin species (i.e. Na-heparin, Ca-heparin, and heparinoids). Multivariate analysis using principal component analysis (PCA), soft independent modelling of class analogy (SIMCA), and partial least squares – discriminant analysis (PLS-DA) were applied for the modelling of spectral data. Different pre-processing methods were applied to IR spectral data; multiplicative scatter correction (MSC) was chosen as the most relevant. Obtained results were confirmed by nuclear magnetic resonance (NMR) spectroscopy. Good predictive ability of this approach demonstrates the potential of IR spectroscopy and chemometrics for screening of heparin quality. This approach, however, is designed as a screening tool and is not considered as a replacement for either of the methods required by USP and FDA. KW - IR spectroscopy KW - Heparin KW - Authenticity KW - Principal component analysis KW - Soft independent modeling of class analogy Y1 - 2021 SN - 0731-7085 U6 - https://doi.org/10.1016/j.jpba.2020.113811 VL - 194 IS - Article number: 113811 PB - Elsevier CY - Amsterdam ER - TY - JOUR A1 - Monakhova, Yulia A1 - Diehl, Bernd W.K. T1 - Novel approach of qNMR workflow by standardization using 2H integral: Application to any intrinsic calibration standard JF - Talanta N2 - Quantitative nuclear magnetic resonance (qNMR) is routinely performed by the internal or external standardization. The manuscript describes a simple alternative to these common workflows by using NMR signal of another active nuclei of calibration compound. For example, for any arbitrary compound quantification by NMR can be based on the use of an indirect concentration referencing that relies on a solvent having both 1H and 2H signals. To perform high-quality quantification, the deuteration level of the utilized deuterated solvent has to be estimated. In this contribution the new method was applied to the determination of deuteration levels in different deuterated solvents (MeOD, ACN, CDCl3, acetone, benzene, DMSO-d6). Isopropanol-d6, which contains a defined number of deuterons and protons, was used for standardization. Validation characteristics (precision, accuracy, robustness) were calculated and the results showed that the method can be used in routine practice. Uncertainty budget was also evaluated. In general, this novel approach, using standardization by 2H integral, benefits from reduced sample preparation steps and uncertainties, and can be applied in different application areas (purity determination, forensics, pharmaceutical analysis, etc.). KW - qNMR KW - Deuterium NMR KW - Deuterated solvents KW - Standardization Y1 - 2021 SN - 0039-9140 U6 - https://doi.org/10.1016/j.talanta.2020.121504 VL - 222 IS - Article number: 121504 PB - Elsevier ER - TY - JOUR A1 - Monakhova, Yulia A1 - Soboleva, Polina M. A1 - Fedotova, Elena S. A1 - Musina, Kristina T. A1 - Burmistrova, Natalia A. T1 - Quantum chemical calculations of IR spectra of heparin disaccharide subunits JF - Computational and Theoretical Chemistry N2 - Heparin is a natural polysaccharide, which plays essential role in many biological processes. Alterations in building blocks can modify biological roles of commercial heparin products, due to significant changes in the conformation of the polymer chain. The variability structure of heparin leads to difficulty in quality control using different analytical methods, including infrared (IR) spectroscopy. In this paper molecular modelling of heparin disaccharide subunits was performed using quantum chemistry. The structural and spectral parameters of these disaccharides have been calculated using RHF/6-311G. In addition, over-sulphated chondroitin sulphate disaccharide was studied as one of the most widespread contaminants of heparin. Calculated IR spectra were analyzed with respect to specific structure parameters. IR spectroscopic fingerprint was found to be sensitive to substitution pattern of disaccharide subunits. Vibrational assignments of calculated spectra were correlated with experimental IR spectral bands of native heparin. Chemometrics was used to perform multivariate analysis of simulated spectral data. KW - IR spectroscopy KW - Chemometrics KW - Quantum chemistry KW - Molecular modelling KW - Quality control Y1 - 2022 SN - 2210-271X U6 - https://doi.org/10.1016/j.comptc.2022.113891 VL - 1217 IS - Article number: 113891 PB - Elsevier CY - New York, NY ER - TY - JOUR A1 - Burger, René A1 - Lindner, Simon A1 - Rumpf, Jessica A1 - Do, Xuan Tung A1 - Diehl, Bernd W.K. A1 - Rehahn, Matthias A1 - Monakhova, Yulia A1 - Schulze, Margit T1 - Benchtop versus high field NMR: Comparable performance found for the molecular weight determination of lignin JF - Journal of Pharmaceutical and Biomedical Analysis N2 - Lignin is a promising renewable biopolymer being investigated worldwide as an environmentally benign substitute of fossil-based aromatic compounds, e.g. for the use as an excipient with antioxidant and antimicrobial properties in drug delivery or even as active compound. For its successful implementation into process streams, a quick, easy, and reliable method is needed for its molecular weight determination. Here we present a method using 1H spectra of benchtop as well as conventional NMR systems in combination with multivariate data analysis, to determine lignin’s molecular weight (Mw and Mn) and polydispersity index (PDI). A set of 36 organosolv lignin samples (from Miscanthus x giganteus, Paulownia tomentosa and Silphium perfoliatum) was used for the calibration and cross validation, and 17 samples were used as external validation set. Validation errors between 5.6% and 12.9% were achieved for all parameters on all NMR devices (43, 60, 500 and 600 MHz). Surprisingly, no significant difference in the performance of the benchtop and high-field devices was found. This facilitates the application of this method for determining lignin’s molecular weight in an industrial environment because of the low maintenance expenditure, small footprint, ruggedness, and low cost of permanent magnet benchtop NMR systems. KW - NMR KW - PLS-regression KW - Molecular weight determination KW - Chemometrics KW - Biomass Y1 - 2022 SN - 0731-7085 U6 - https://doi.org/10.1016/j.jpba.2022.114649 VL - 212 IS - Article number: 114649 PB - Elsevier CY - New York, NY ER - TY - JOUR A1 - Monakhova, Yulia A1 - Diehl, Bernd W.K. T1 - Multinuclear NMR screening of pharmaceuticals using standardization by 2H integral of a deuterated solvent JF - Journal of Pharmaceutical and Biomedical Analysis N2 - NMR standardization approach that uses the 2H integral of deuterated solvent for quantitative multinuclear analysis of pharmaceuticals is described. As a proof of principle, the existing NMR procedure for the analysis of heparin products according to US Pharmacopeia monograph is extended to the determination of Na+ and Cl- content in this matrix. Quantification is performed based on the ratio of a 23Na (35Cl) NMR integral and 2H NMR signal of deuterated solvent, D2O, acquired using the specific spectrometer hardware. As an alternative, the possibility of 133Cs standardization using the addition of Cs2CO3 stock solution is shown. Validation characteristics (linearity, repeatability, sensitivity) are evaluated. A holistic NMR profiling of heparin products can now also be used for the quantitative determination of inorganic compounds in a single analytical run using a single sample. In general, the new standardization methodology provides an appealing alternative for the NMR screening of inorganic and organic components in pharmaceutical products. KW - NMR spectroscopy KW - Inorganic ions KW - Heparin KW - Standardization Y1 - 2022 SN - 0731-7085 U6 - https://doi.org/10.1016/j.jpba.2021.114530 VL - 209 IS - Article number: 114530 PB - Elsevier ER - TY - JOUR A1 - Lindner, Simon A1 - Burger, René A1 - Rutledge, Douglas N. A1 - Do, Xuan Tung A1 - Rumpf, Jessica A1 - Diehl, Bernd W. K. A1 - Schulze, Margit A1 - Monakhova, Yulia T1 - Is the calibration transfer of multivariate calibration models between high- and low-field NMR instruments possible? A case study of lignin molecular weight JF - Analytical chemistry N2 - Although several successful applications of benchtop nuclear magnetic resonance (NMR) spectroscopy in quantitative mixture analysis exist, the possibility of calibration transfer remains mostly unexplored, especially between high- and low-field NMR. This study investigates for the first time the calibration transfer of partial least squares regressions [weight average molecular weight (Mw) of lignin] between high-field (600 MHz) NMR and benchtop NMR devices (43 and 60 MHz). For the transfer, piecewise direct standardization, calibration transfer based on canonical correlation analysis, and transfer via the extreme learning machine auto-encoder method are employed. Despite the immense resolution difference between high-field and low-field NMR instruments, the results demonstrate that the calibration transfer from high- to low-field is feasible in the case of a physical property, namely, the molecular weight, achieving validation errors close to the original calibration (down to only 1.2 times higher root mean square errors). These results introduce new perspectives for applications of benchtop NMR, in which existing calibrations from expensive high-field instruments can be transferred to cheaper benchtop instruments to economize. Y1 - 2022 SN - 1520-6882 U6 - https://doi.org/10.1021/acs.analchem.1c05125 VL - 94 IS - 9 SP - 3997 EP - 4004 PB - ACS Publications CY - Washington, DC ER - TY - CHAP A1 - Brockmann, Carsten A1 - Sultanow, Eldar A1 - Czarnecki, Christian ED - Czarnecki, Christian ED - Brockmann, Carsten ED - Sultanow, Eldar ED - Koschmider, Agnes ED - Selzer, Annika ED - Gesellschaft für Informatik e. V., T1 - Enterprise architectures between agility and traditional methodologies T2 - GI Edition Proceedings Band 285 Workshops der INFORMATIK 2018 N2 - For this year’s workshop on Enterpirse Architecture in Research and Practice we have received eight submissions from which four have passed the rigorous peer-review. The acceptance quote of 50% assures that only advancements in the field are included in our workshop. KW - Agility KW - agile KW - Enterprise Architecture Y1 - 2018 SN - 9783885796794 SN - 1617-5468 N1 - 26.-27. September 2018 Berlin PB - Köllen CY - Bonn ER - TY - CHAP A1 - Bensberg, Frank A1 - Auth, Gunnar A1 - Czarnecki, Christian A1 - Wörndle, Christopher ED - Kemal İlter, H. T1 - Transforming literature-intensive research processes through text analytics – design, implementation and lessons learned N2 - The continuing growth of scientific publications raises the question how research processes can be digitalized and thus realized more productively. Especially in information technology fields, research practice is characterized by a rapidly growing volume of publications. For the search process various information systems exist. However, the analysis of the published content is still a highly manual task. Therefore, we propose a text analytics system that allows a fully digitalized analysis of literature sources. We have realized a prototype by using EBSCO Discovery Service in combination with IBM Watson Explorer and demonstrated the results in real-life research projects. Potential addressees are research institutions, consulting firms, and decision-makers in politics and business practice. KW - Text analytics KW - Text mining KW - Literature review KW - Research process Y1 - 2018 U6 - https://doi.org/10.6084/m9.figshare.7582073.v1 N1 - 5th International Management Information Systems Conference. October 24-26 2018, Ankara ER - TY - CHAP A1 - Brockmann, Carsten A1 - Sultanow, Eldar A1 - Czarnecki, Christian ED - Draude, Claude ED - Lange, Martin ED - Sick, Bernhard T1 - Is enterprise architecture still relevant in the digital age? T2 - GI Edition Proceedings Band 295 INFORMATIK 2019, Workshop-Beiträge KW - Preface KW - Enterprise Architecture KW - Digital Age Y1 - 2019 SN - 9783885796893 U6 - https://doi.org/10.18420/inf2019_ws01 SN - 1617-5468 N1 - 50 Jahre Gesellschaft für Informatik – Informatik für Gesellschaft. 16. September, Kassel SP - 21 EP - 21 PB - Köllen CY - Bonn ER - TY - CHAP A1 - Auth, Gunnar A1 - Czarnecki, Christian A1 - Bensberg, Frank ED - Draude, Claude ED - Lange, Martin ED - Sick, Bernhard ED - Gesellschaft für Informatik e.V. (GI), T1 - Impact of robotic process automation on enterprise architectures T2 - GI Edition Proceedings Band 295 INFORMATIK 2019, Workshop-Beiträge N2 - The initial idea of Robotic Process Automation (RPA) is the automation of business processes through the presentation layer of existing application systems. For this simple emulation of user input and output by software robots, no changes of the systems and architecture is required. However, considering strategic aspects of aligning business and technology on an enterprise level as well as the growing capabilities of RPA driven by artificial intelligence, interrelations between RPA and Enterprise Architecture (EA) become visible and pose new questions. In this paper we discuss the relationship between RPA and EA in terms of perspectives and implications. As workin- progress we focus on identifying new questions and research opportunities related to RPA and EA. KW - Robotic Process Automation KW - Enterprise Architecture KW - Software Robots Y1 - 2019 SN - 9783885796893 U6 - https://doi.org/10.18420/inf2019_ws05 SN - 1617-5468 N1 - 50 Jahre Gesellschaft für Informatik – Informatik für Gesellschaft. 16. September, Kassel SP - 59 EP - 65 PB - Köllen CY - Bonn ER - TY - CHAP A1 - Ritschel, Konstantin A1 - Stenzel, Adina A1 - Czarnecki, Christian A1 - Hong, Chin-Gi ED - Gesellschaft für Informatik e.V. (GI), T1 - Realizing robotic process automation potentials: an architectural perspective on a real-life implementation case T2 - GI Edition Proceedings Band 314 "INFORMATIK 2021" Computer Science & Sustainability N2 - The initial idea of Robotic Process Automation (RPA) is the automation of business processes through a simple emulation of user input and output by software robots. Hence, it can be assumed that no changes of the used software systems and existing Enterprise Architecture (EA) is required. In this short, practical paper we discuss this assumption based on a real-life implementation project. We show that a successful RPA implementation might require architectural work during analysis, implementation, and migration. As practical paper we focus on exemplary lessons-learned and new questions related to RPA and EA. KW - Robotic Process Automation KW - Enterprise Architecture KW - Implementation Case Y1 - 2021 SN - 9783885797081 U6 - https://doi.org/10.18420/informatik2021-108 SN - 1617-5468 N1 - INFORMATIK 2021 – 51. Jahrestagung der Gesellschaft für Informatik, 27. September – 01. Oktober 2021 / Virtuell SP - 1303 EP - 1311 PB - Köllen CY - Bonn ER - TY - CHAP A1 - Amir, Malik A1 - Bauckhage, Christian A1 - Chircu, Alina A1 - Czarnecki, Christian A1 - Knopf, Christian A1 - Piatkowski, Nico A1 - Sultanow, Eldar T1 - What can we expect from quantum (digital) twins? T2 - Wirtschaftsinformatik 2022 Proceedings N2 - Digital twins enable the modeling and simulation of real-world entities (objects, processes or systems), resulting in improvements in the associated value chains. The emerging field of quantum computing holds tremendous promise forevolving this virtualization towards Quantum (Digital) Twins (QDT) and ultimately Quantum Twins (QT). The quantum (digital) twin concept is not a contradiction in terms - but instead describes a hybrid approach that can be implemented using the technologies available today by combining classicalcomputing and digital twin concepts with quantum processing. This paperpresents the status quo of research and practice on quantum (digital) twins. It alsodiscuses their potential to create competitive advantage through real-timesimulation of highly complex, interconnected entities that helps companies better address changes in their environment and differentiate their products andservices. KW - Artificial Intelligence KW - Digital Twin Evolution KW - Machine Learning KW - Quantum Computing KW - Quantum Machine Learning Y1 - 2022 N1 - 17. Internationale Tagung Wirtschaftsinformatik, 21. – 23. Februar 2022, Nürnberg (online) SP - 1 EP - 14 PB - AIS Electronic Library (AISeL) ER - TY - JOUR A1 - Eggert, Mathias A1 - Kreuzer, Vincent T1 - Sprachsteuerung im Gesundheitswesen – Anforderungen und Auswahl geeigneter Anbieter T1 - Voice control in healthcare—requirements and provider selection JF - HMD Praxis der Wirtschaftsinformatik N2 - Das Gesundheitswesen ist konfrontiert mit steigenden Kosten und einer immer schwieriger werdenden Personalsituation. Zeitgleich versprechen moderne Sprachsteuerungssysteme Prozesse in Arztpraxen und Krankenhäusern zu verschlanken und Vorgänge zu beschleunigen. Dennoch wird derzeit der Einsatz von Sprachsteuerungssystemen in Arztpraxen oder Krankenhäusern nur selten beobachtet, was auch an den besonders strengen Datenschutzauflagen der Datenschutzgrundverordnung (DSGVO) liegt. Darüber hinaus wirft die niedrige Nutzungsrate die Frage nach den konkreten Anforderungen und ihrer Umsetzbarkeit auf, was durch den vorliegenden Beitrag adressiert wird, indem die Ergebnisse von Interviews mit acht medizinischen Fachexperten ausgewertet werden. Ergänzend wird die technische Umsetzbarkeit einzelner Anforderungen mit unterschiedlichen Cloud-Anbietern erprobt. KW - Gesundheitswesen KW - Sprachsteuerung KW - Sprachassistent KW - Anforderungen KW - Umsetzbarkeit Y1 - 2022 SN - 2198-2775 U6 - https://doi.org/10.1365/s40702-022-00919-z SN - 1436-3011 N1 - Corresponding author: Mathias Eggert VL - 59 SP - 1640 EP - 1652 PB - Springer Vieweg CY - Wiesbaden ER - TY - JOUR A1 - Schüller-Ruhl, Aaron A1 - Dinstühler, Leonard A1 - Senger, Thorsten A1 - Bergfeld, Stefan A1 - Ingenhag, Christian A1 - Fleischhaker, Robert ED - Mackenzie, Jacob T1 - Direct fabrication of arbitrary phase masks in optical glass via ultra-short pulsed laser writing of refractive index modifications JF - Applied Physics B N2 - We study the possibility to fabricate an arbitrary phase mask in a one-step laser-writing process inside the volume of an optical glass substrate. We derive the phase mask from a Gerchberg–Saxton-type algorithm as an array and create each individual phase shift using a refractive index modification of variable axial length. We realize the variable axial length by superimposing refractive index modifications induced by an ultra-short pulsed laser at different focusing depth. Each single modification is created by applying 1000 pulses with 15 μJ pulse energy at 100 kHz to a fixed spot of 25 μm diameter and the focus is then shifted axially in steps of 10 μm. With several proof-of-principle examples, we show the feasibility of our method. In particular, we identify the induced refractive index change to about a value of Δn=1.5⋅10−3. We also determine our current limitations by calculating the overlap in the form of a scalar product and we discuss possible future improvements. Y1 - 2022 U6 - https://doi.org/10.1007/s00340-022-07928-2 SN - 1432-0649 (Online) SN - 0946-2171 (Print) N1 - Corresponding author: Robert Fleischhaker VL - 128 IS - Article number: 208 SP - 1 EP - 11 PB - Springer CY - Berlin ER - TY - CHAP A1 - Blaneck, Patrick Gustav A1 - Bornheim, Tobias A1 - Grieger, Niklas A1 - Bialonski, Stephan T1 - Automatic readability assessment of german sentences with transformer ensembles T2 - Proceedings of the GermEval 2022 Workshop on Text Complexity Assessment of German Text N2 - Reliable methods for automatic readability assessment have the potential to impact a variety of fields, ranging from machine translation to self-informed learning. Recently, large language models for the German language (such as GBERT and GPT-2-Wechsel) have become available, allowing to develop Deep Learning based approaches that promise to further improve automatic readability assessment. In this contribution, we studied the ability of ensembles of fine-tuned GBERT and GPT-2-Wechsel models to reliably predict the readability of German sentences. We combined these models with linguistic features and investigated the dependence of prediction performance on ensemble size and composition. Mixed ensembles of GBERT and GPT-2-Wechsel performed better than ensembles of the same size consisting of only GBERT or GPT-2-Wechsel models. Our models were evaluated in the GermEval 2022 Shared Task on Text Complexity Assessment on data of German sentences. On out-of-sample data, our best ensemble achieved a root mean squared error of 0:435. Y1 - 2022 U6 - https://doi.org/10.48550/arXiv.2209.04299 N1 - Proceedings of the 18th Conference on Natural Language Processing / Konferenz zur Verarbeitung natürlicher Sprache (KONVENS 2022), 12-15 September, 2022, University of Potsdam, Potsdam, Germany SP - 57 EP - 62 PB - Association for Computational Linguistics CY - Potsdam ER - TY - CHAP A1 - Steuer-Dankert, Linda A1 - Sharma, Mamta Rameshwarlal A1 - Bleck, Wolfgang A1 - Leicht-Scholten, Carmen ED - Farn, C. K. T1 - Innovation through Diversity - Development of a Diversity and Innovation management concept T2 - International Conference on Innovation and Management : IAM23017S : Date: July 4-7, 2017, Osaka, Japan N2 - Acknowledging that a diverse workforce could be a potential source of innovation, the current research deals with the fine details of why diversity management is central to achieving innovation in heterogeneous research groups and how this could be effectively realized in an organization. The types of heterogeneities addressed mainly include gender, qualification, academic discipline and intercultural perspectives. The type of organization being dealt with in this work is a complex association of research institutes at a technical university in Germany (RWTH Aachen University), namely a 'Cluster of Excellence', whereby several institutes of the university work collaboratively in different sub-projects. The 'Cluster of Excellence' is a part of the 'Excellence Initiative' of the German federal and state governments German Research Foundation (DFG) and German Council of Science and Humanities, with the ultimate aim of promoting cutting-edge research. To support interdisciplinary collaboration and thus the performance of the cluster, the development of a diversity and innovation management concept is presently in the conceptual phase and will be described in the frame of this paper. The 3-S-Diversity Model, composed of the three elements: skills, structure and strategy, serves as a basis for the development of the concept. The proposed concept consists of six phases; the first two phases lay the ground work by developing an understanding of the status quo on the forms of diversity in the Cluster of Excellence, the type of organizational structure of the member institutes and the varieties of specialist work cultures of the same. The third and the fourth phases build up on this foundation by means of qualitative and quantitative studies. While the third phase deals with the sensitization of the management level to the close connection between diversity and innovation; the need to manage them thereafter and find tailor-made methods of doing so, the fourth phase shall mainly focus on the mindset of the employees in this regard. The fifth phase shall consolidate the learnings and the ideas developed in the course of the first four phases into an implementable strategy. The ultimate phase shall be the implementation of this concept in the Cluster. The first three phases have been accomplished successfully and the preliminary results are already available. Y1 - 2017 SN - 2218-6387 SP - Panel C PB - Kuang Hui Chiu CY - Osaka ER - TY - JOUR A1 - Molinnus, Denise A1 - Janus, Kevin Alexander A1 - Fang, Anyelina C. A1 - Drinic, Aleksander A1 - Achtsnicht, Stefan A1 - Köpf, Marius A1 - Keusgen, Michael A1 - Schöning, Michael Josef T1 - Thick-film carbon electrode deposited onto a biodegradable fibroin substrate for biosensing applications JF - Physica status solidi (a) N2 - This study addresses a proof-of-concept experiment with a biocompatible screen-printed carbon electrode deposited onto a biocompatible and biodegradable substrate, which is made of fibroin, a protein derived from silk of the Bombyx mori silkworm. To demonstrate the sensor performance, the carbon electrode is functionalized as a glucose biosensor with the enzyme glucose oxidase and encapsulated with a silicone rubber to ensure biocompatibility of the contact wires. The carbon electrode is fabricated by means of thick-film technology including a curing step to solidify the carbon paste. The influence of the curing temperature and curing time on the electrode morphology is analyzed via scanning electron microscopy. The electrochemical characterization of the glucose biosensor is performed by amperometric/voltammetric measurements of different glucose concentrations in phosphate buffer. Herein, systematic studies at applied potentials from 500 to 1200 mV to the carbon working electrode (vs the Ag/AgCl reference electrode) allow to determine the optimal working potential. Additionally, the influence of the curing parameters on the glucose sensitivity is examined over a time period of up to 361 days. The sensor shows a negligible cross-sensitivity toward ascorbic acid, noradrenaline, and adrenaline. The developed biocompatible biosensor is highly promising for future in vivo and epidermal applications. KW - biocompatible materials KW - biodegradable electronic devices KW - biosensors KW - carbon electrodes KW - glucose Y1 - 2022 U6 - https://doi.org/10.1002/pssa.202200100 SN - 1862-6319 N1 - Corresponding author: Michael J. Schöning VL - 219 IS - 23 SP - 1 EP - 9 PB - Wiley-VCH CY - Weinheim ER - TY - JOUR A1 - Maurischat, Andreas T1 - Algebraic independence of the Carlitz period and its hyperderivatives JF - Journal of Number Theory KW - Drinfeld modules KW - Periods KW - t-modules KW - Transcendence KW - Higher derivations Y1 - 2022 U6 - https://doi.org/10.1016/j.jnt.2022.01.006 SN - 0022-314X VL - 240 SP - 145 EP - 162 PB - Elsevier CY - Orlando, Fla. ER - TY - JOUR A1 - Kotliar, Konstantin A1 - Ortner, Marion A1 - Conradi, Anna A1 - Hacker, Patricia A1 - Hauser, Christine A1 - Günthner, Roman A1 - Moser, Michaela A1 - Muggenthaler, Claudia A1 - Diehl-Schmid, Janine A1 - Priller, Josef A1 - Schmaderer, Christoph A1 - Grimmer, Timo T1 - Altered retinal cerebral vessel oscillation frequencies in Alzheimer's disease compatible with impaired amyloid clearance JF - Neurobiology of Aging N2 - Retinal vessels are similar to cerebral vessels in their structure and function. Moderately low oscillation frequencies of around 0.1 Hz have been reported as the driving force for paravascular drainage in gray matter in mice and are known as the frequencies of lymphatic vessels in humans. We aimed to elucidate whether retinal vessel oscillations are altered in Alzheimer's disease (AD) at the stage of dementia or mild cognitive impairment (MCI). Seventeen patients with mild-to-moderate dementia due to AD (ADD); 23 patients with MCI due to AD, and 18 cognitively healthy controls (HC) were examined using Dynamic Retinal Vessel Analyzer. Oscillatory temporal changes of retinal vessel diameters were evaluated using mathematical signal analysis. Especially at moderately low frequencies around 0.1 Hz, arterial oscillations in ADD and MCI significantly prevailed over HC oscillations and correlated with disease severity. The pronounced retinal arterial vasomotion at moderately low frequencies in the ADD and MCI groups would be compatible with the view of a compensatory upregulation of paravascular drainage in AD and strengthen the amyloid clearance hypothesis. KW - Alzheimer's disease KW - Retinal vessel analysis KW - Vasomotions KW - Pulsations KW - Mild cognitive impairment Y1 - 2022 U6 - https://doi.org/10.1016/j.neurobiolaging.2022.08.012 SN - 0197-4580 VL - 120 SP - 117 EP - 127 PB - Elsevier CY - Amsterdam ER - TY - JOUR A1 - Colombo, Daniele A1 - Drira, Slah A1 - Frotscher, Ralf A1 - Staat, Manfred T1 - An element-based formulation for ES-FEM and FS-FEM models for implementation in standard solid mechanics finite element codes for 2D and 3D static analysis JF - International Journal for Numerical Methods in Engineering N2 - Edge-based and face-based smoothed finite element methods (ES-FEM and FS-FEM, respectively) are modified versions of the finite element method allowing to achieve more accurate results and to reduce sensitivity to mesh distortion, at least for linear elements. These properties make the two methods very attractive. However, their implementation in a standard finite element code is nontrivial because it requires heavy and extensive modifications to the code architecture. In this article, we present an element-based formulation of ES-FEM and FS-FEM methods allowing to implement the two methods in a standard finite element code with no modifications to its architecture. Moreover, the element-based formulation permits to easily manage any type of element, especially in 3D models where, to the best of the authors' knowledge, only tetrahedral elements are used in FS-FEM applications found in the literature. Shape functions for non-simplex 3D elements are proposed in order to apply FS-FEM to any standard finite element. KW - distorted element KW - ES-FEM KW - FS-FEM KW - non-simplex S-FEM elements KW - S-FEM Y1 - 2022 U6 - https://doi.org/10.1002/nme.7126 SN - 1097-0207 VL - 124 IS - 2 SP - 402 EP - 433 PB - Wiley CY - Chichester ER - TY - JOUR A1 - Bhattarai, Aroj A1 - May, Charlotte Anabell A1 - Staat, Manfred A1 - Kowalczyk, Wojciech A1 - Tran, Thanh Ngoc T1 - Layer-specific damage modeling of porcine large intestine under biaxial tension JF - Bioengineering N2 - The mechanical behavior of the large intestine beyond the ultimate stress has never been investigated. Stretching beyond the ultimate stress may drastically impair the tissue microstructure, which consequently weakens its healthy state functions of absorption, temporary storage, and transportation for defecation. Due to closely similar microstructure and function with humans, biaxial tensile experiments on the porcine large intestine have been performed in this study. In this paper, we report hyperelastic characterization of the large intestine based on experiments in 102 specimens. We also report the theoretical analysis of the experimental results, including an exponential damage evolution function. The fracture energies and the threshold stresses are set as damage material parameters for the longitudinal muscular, the circumferential muscular and the submucosal collagenous layers. A biaxial tensile simulation of a linear brick element has been performed to validate the applicability of the estimated material parameters. The model successfully simulates the biomechanical response of the large intestine under physiological and non-physiological loads. KW - biaxial tensile experiment KW - anisotropy KW - hyperelastic KW - constitutive modeling KW - damage Y1 - 2022 U6 - https://doi.org/10.3390/bioengineering9100528 SN - 2306-5354 N1 - Der Artikel gehört zum Sonderheft "Computational Biomechanics" VL - 9 IS - 10, Early Access SP - 1 EP - 17 PB - MDPI CY - Basel ER - TY - THES A1 - Bergerhausen, Florian T1 - Die Chance der fiktionalen Literatur : Literatur der Fiktion als Anstoß für Information und Diskurs N2 - Der informative Charakter fiktionaler Texte sollte nicht unterschätzt werden. Mit dem Projekt wird durch „Buddenbrooks“ von Thomas Mann gezeigt, wie relevante und redebedürftige Themen in der Literatur angesprochen werden. Dafür gibt es zusätzliche Text- und Info-Impulse als ergänzendes Buch zum Roman. Neben diesen Vertiefungsbüchern gibt es eine Inszenierung des Buches mit Beispielen aus den Büchern. Die Ausstellung kann Teil eines Messestandes sein oder für sich existieren und bietet einen ersten Kontakt mit der Idee des Projektes und mit den Büchern selbst. Zusätzliches Interesse an der Arbeit wird durch Social Media Posts generiert, die den wichtigen Part des Austauschs und der Diskussion fördern, wozu das Projekt auch anregen möchte. „Die Chance der fiktionalen Literatur“ regt Leser:innen an, fiktionale Literatur anders zu betrachten und einen größeren Nutzen aus der Fiktion zu ziehen. KW - Editorial Design KW - Illustration KW - Szenografie KW - Literatur KW - Buch Y1 - 2022 PB - FH Aachen CY - Aachen ER - TY - THES A1 - Böhler, Jennifer T1 - Environmental injustice : how environmental inequality impacts low socio-economic communities. N2 - Das Projekt beschäftigt sich mit der Informationsvermittlung zu dem Thema “Environmental Injustice” in Form einer Website. “Environmental Injustice” beschreibt die systematische unfaire Behandlung von verschiedenen Communities durch Länder/Regierungen, Firmen und unabhängige Akteure. In dem Bereich werden weitestgehend Schäden im Zusammenhang mit Ressourcen, dessen Abbau, gefährlichen Abfällen und Chancenungleichheit beschrieben. Das Projekt ist generell eine Sammlung, die als Anlaufstelle zur Weiterbildung in dem Thema dienen soll. Dies geschieht durch gestalterische Aufarbeitung, Illustration und Kategorisierung. KW - Informationsdesign KW - Illustration KW - Umweltungerechtigkeit KW - Website KW - Webdesign Y1 - 2022 PB - FH Aachen CY - Aachen ER - TY - THES A1 - Büchel, Carolin T1 - GYMLET : dein mobiles Freiluftstudio - Entwicklung eines serientauglichen Prototypen und einer Vermarktungsstrategie N2 - Sportvereine verlieren zunehmend Mitglieder. Grund dafür ist der wachsende Wunsch nach unabhängigen Trainingsmöglichkeiten. GYMLET bietet den Sportler:innen die Möglichkeit, ihre Fitness funktional, selbstorganisiert und unabhängig zu trainieren. Dabei kann durch den selbstbestimmten Trainingsort neben der körperlichen Fitness vor allem die Motivation zur sportlichen Aktivität und das Wohlbefinden gesteigert werden. Unterstützt wird das Trainingssystem durch eine App, welche den Sportler:innen neben Nutzungsmöglichkeiten als Coach und Trainingsplaner dient. Um diese Trainingsmöglichkeit an die Zielgruppe heranzutragen, ist eine Kampagnenstrategie aus zwei Phasen entstanden. In dieser sollen Postings und Clips über Instagram und Youtube veröffentlicht werden. Zusätzlich werden Zeitschriften und mögliche Kooperationen mit Therapeuten oder Freizeitunterkünften zur Veröffentlichung der Kampagne genutzt. KW - Fitnesstraining KW - Kampagne KW - Outdoortraining KW - selbstorganisiertes Training KW - Freizeitsport Y1 - 2022 PB - FH Aachen CY - Aachen ER - TY - THES A1 - Eigel, Nick T1 - uCo - the universal communicator : robotische Konversationen unserer Zukunft N2 - Kommunikationsroboter für den Kundenservice. Aktuell werden große Fortschritte im Bereich von künstlicher Intelligenz und Robotik getätigt, sodass wir bald intelligente Maschinen unter uns haben werden. Daher müssen wir uns die Frage beantworten, welche Rolle diese einnehmen sollen und vor allem wie wir mit ihnen interagieren und kommunizieren wollen. "uCo" bewältigt dies mithilfe einer mobilen, robotischen Plattform, welche mit einem holografischen 3-D-Interface ausgestattet ist. Neben der Entwicklung des robotischen Körpers beinhaltet das Projekt "uCo" die Grundlage für ein Kommunikationssystem für "uCo's" Gesicht. "uCo" kommuniziert hauptsächlich über Sprache, wird dabei jedoch von einem speziell entwickelten Mimik- und Emotionssytem unterstützt. "uCo" als Konzept versucht, erste Antworten auf die komplexen gestalterischen und moralischen Fragen zu geben, die mit der Entwicklung von künstlicher Intelligenz einhergehen. Und wer weiß - vielleicht wirst du eines Tages von einem "uCo" beraten. KW - Robotik KW - Hologram KW - Kommunikation KW - künstliche Intelligenz KW - KI Y1 - 2022 PB - FH Aachen CY - Aachen ER - TY - THES A1 - Geilhausen, Ayleen T1 - SUE : Restauranterlebnisse neu gestalten N2 - Gastronomiebetriebe, insbesondere diese ohne zeitgemäße und durchdachte Konzepte wurden durch die Pandemie stark getroffen. Während große Fast-Food-Ketten bereits vor der Pandemie digitale Lösungen einsetzten, stehen nun auch andere Restaurantbetreiber:innen vor der Herausforderung der Digitalisierung. Gerade die Pandemie hat an dieser Stelle verdeutlicht, welche Restaurants ihre Prozesse im Sinne der User Experience durchdacht haben und welche nicht. Die Tisch-Stuhl-Kombination der „SUE“-Serie bietet Restaurants, smarte und elegante Gastronomiemöbel, die je nach Konzept in Materialität und Farbe frei anpassbar sind. Wandelbarkeit, Komfort und die Integration digitaler Lösungen sind die Kernkompetenzen und Anforderungen, die das Gastronomie-Interior in Zukunft erfüllen muss. Der smarte Bistrotisch und der wandelbare Stuhl der „SUE“-Serie zeigt einen digitalisierten und anpassbaren Lösungsansatz. KW - Restaurantmöbel KW - Gastronomie KW - Designstuhl KW - Restauranttisch KW - Produktdesign Y1 - 2022 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER - TY - CHAP A1 - Striebing, Clemens A1 - Müller, Jörg A1 - Schraudner, Martina A1 - Gewinner, Irina Valerie A1 - Guerrero Morales, Patricia A1 - Hochfeld, Katharina A1 - Hoffman, Shekinah A1 - Kmec, Julie A. A1 - Nguyen, Huu Minh A1 - Schneider, Jannick A1 - Sheridan, Jennifer A1 - Steuer-Dankert, Linda A1 - Trimble O'Connor, Lindsey A1 - Vandevelde-Rougale, Agnès T1 - Promoting diversity and combatting discrimination in research organizations: a practitioner’s guide T2 - Diversity and discrimination in research organizations N2 - The essay is addressed to practitioners in research management and from academic leadership. It describes which measures can contribute to creating an inclusive climate for research teams and preventing and effectively dealing with discrimination. The practical recommendations consider the policy and organizational levels, as well as the individual perspective of research managers. Following a series of basic recommendations, six lessons learned are formulated, derived from the contributions to the edited collection on “Diversity and Discrimination in Research Organizations.” KW - Inclusive work climate KW - lessons learned KW - policy recommendations KW - recommendations for actions KW - bullying Y1 - 2022 SN - 978-1-80117-959-1 (Print) SN - 978-1-80117-956-0 (Online) U6 - https://doi.org/10.1108/978-1-80117-956-020221012 SP - 421 EP - 442 PB - Emerald Publishing Limited CY - Bingley ER - TY - CHAP A1 - Steuer-Dankert, Linda A1 - Leicht-Scholten, Carmen T1 - Perceiving diversity : an explorative approach in a complex research organization. T2 - Diversity and discrimination in research organizations N2 - Diversity management is seen as a decisive factor for ensuring the development of socially responsible innovations (Beacham and Shambaugh, 2011; Sonntag, 2014; López, 2015; Uebernickel et al., 2015). However, many diversity management approaches fail due to a one-sided consideration of diversity (Thomas and Ely, 2019) and a lacking linkage between the prevailing organizational culture and the perception of diversity in the respective organization. Reflecting the importance of diverse perspectives, research institutions have a special responsibility to actively deal with diversity, as they are publicly funded institutions that drive socially relevant development and educate future generations of developers, leaders and decision-makers. Nevertheless, only a few studies have so far dealt with the influence of the special framework conditions of the science system on diversity management. Focusing on the interdependency of the organizational culture and diversity management especially in a university research environment, this chapter aims in a first step to provide a theoretical perspective on the framework conditions of a complex research organization in Germany in order to understand the system-specific factors influencing diversity management. In a second step, an exploratory cluster analysis is presented, investigating the perception of diversity and possible influencing factors moderating this perception in a scientific organization. Combining both steps, the results show specific mechanisms and structures of the university research environment that have an impact on diversity management and rigidify structural barriers preventing an increase of diversity. The quantitative study also points out that the management level takes on a special role model function in the scientific system and thus has an influence on the perception of diversity. Consequently, when developing diversity management approaches in research organizations, it is necessary to consider the top-down direction of action, the special nature of organizational structures in the university research environment as well as the special role of the professorial level as role model for the scientific staff. KW - Diversity management KW - Organizational culture KW - Change management KW - Psychological concepts KW - Perception Y1 - 2022 SN - 978-1-80117-959-1 (Print) SN - 978-1-80117-956-0 (Online) U6 - https://doi.org/10.1108/978-1-80117-956-020221010 SP - 365 EP - 392 PB - Emerald Publishing Limited CY - Bingley ER - TY - CHAP A1 - Hinke, Christian A1 - Vervier, Luisa A1 - Brauner, Philipp A1 - Schneider, Sebastian A1 - Steuer-Dankert, Linda A1 - Ziefle, Martina A1 - Leicht-Scholten, Carmen T1 - Capability configuration in next generation manufacturing T2 - Forecasting next generation manufacturing : digital shadows, human-machine collaboration, and data-driven business models N2 - Industrial production systems are facing radical change in multiple dimensions. This change is caused by technological developments and the digital transformation of production, as well as the call for political and social change to facilitate a transformation toward sustainability. These changes affect both the capabilities of production systems and companies and the design of higher education and educational programs. Given the high uncertainty in the likelihood of occurrence and the technical, economic, and societal impacts of these concepts, we conducted a technology foresight study, in the form of a real-time Delphi analysis, to derive reliable future scenarios featuring the next generation of manufacturing systems. This chapter presents the capabilities dimension and describes each projection in detail, offering current case study examples and discussing related research, as well as implications for policy makers and firms. Specifically, we discuss the benefits of capturing expert knowledge and making it accessible to newcomers, especially in highly specialized industries. The experts argue that in order to cope with the challenges and circumstances of today’s world, students must already during their education at university learn how to work with AI and other technologies. This means that study programs must change and that universities must adapt their structural aspects to meet the needs of the students. Y1 - 2022 SN - 978-3-031-07733-3 U6 - https://doi.org/10.1007/978-3-031-07734-0_6 SP - 95 EP - 106 PB - Springer CY - Cham ER - TY - JOUR A1 - Philipp, Mohr A1 - Efthimiou, Nikos A1 - Pagano, Fiammetta A1 - Kratochwil, Nicolaus A1 - Pizzichemi, Marco A1 - Tsoumpas, Charalampos A1 - Auffray, Etiennette A1 - Ziemons, Karl T1 - Image reconstruction analysis for positron emission tomography with heterostructured scintillators JF - IEEE Transactions on Radiation and Plasma Medical Sciences N2 - The concept of structure engineering has been proposed for exploring the next generation of radiation detectors with improved performance. A TOF-PET geometry with heterostructured scintillators with a pixel size of 3.0×3.1×15 mm3 was simulated using Monte Carlo. The heterostructures consisted of alternating layers of BGO as a dense material with high stopping power and plastic (EJ232) as a fast light emitter. The detector time resolution was calculated as a function of the deposited and shared energy in both materials on an event-by-event basis. While sensitivity was reduced to 32% for 100 μm thick plastic layers and 52% for 50 μm, the CTR distribution improved to 204±49 ps and 220±41 ps respectively, compared to 276 ps that we considered for bulk BGO. The complex distribution of timing resolutions was accounted for in the reconstruction. We divided the events into three groups based on their CTR and modeled them with different Gaussian TOF kernels. On a NEMA IQ phantom, the heterostructures had better contrast recovery in early iterations. On the other hand, BGO achieved a better contrast to noise ratio (CNR) after the 15th iteration due to the higher sensitivity. The developed simulation and reconstruction methods constitute new tools for evaluating different detector designs with complex time responses. KW - TOF PET KW - Heterostructure KW - Metascintillator KW - Multiple TOF kernels KW - Image Reconstruction Y1 - 2022 U6 - https://doi.org/10.1109/TRPMS.2022.3208615 SN - 2469-7311 SN - 2469-7303 VL - 7 IS - 1 SP - 41 EP - 51 PB - IEEE CY - New York, NY ER - TY - CHAP A1 - Allal, D. A1 - Bannister, R. A1 - Buisman, K. A1 - Capriglione, D. A1 - Di Capua, G. A1 - García-Patrón, M. A1 - Gatzweiler, Thomas A1 - Gellersen, F. A1 - Harzheim, Thomas A1 - Heuermann, Holger A1 - Hoffmann, J. A1 - Izbrodin, A. A1 - Kuhlmann, K. A1 - Lahbacha, K. A1 - Maffucci, A. A1 - Miele, G. A1 - Mubarak, F. A1 - Salter, M. A1 - Pham, T.D. A1 - Sayegh, A. A1 - Singh, D. A1 - Stein, F. A1 - Zeier, M. T1 - RF measurements for future communication applications: an overview T2 - 2022 IEEE International Symposium on Measurements & Networking (M&N) N2 - In this paper research activities developed within the FutureCom project are presented. The project, funded by the European Metrology Programme for Innovation and Research (EMPIR), aims at evaluating and characterizing: (i) active devices, (ii) signal- and power integrity of field programmable gate array (FPGA) circuits, (iii) operational performance of electronic circuits in real-world and harsh environments (e.g. below and above ambient temperatures and at different levels of humidity), (iv) passive inter-modulation (PIM) in communication systems considering different values of temperature and humidity corresponding to the typical operating conditions that we can experience in real-world scenarios. An overview of the FutureCom project is provided here, then the research activities are described. KW - FPGA KW - signal integrity KW - power integrity KW - passive inter-modulation KW - metrological characterization Y1 - 2022 SN - 978-1-6654-8362-9 SN - 978-1-6654-8363-6 U6 - https://doi.org/10.1109/MN55117.2022.9887740 SN - 2639-5061 SN - 2639-507X N1 - 2022 IEEE International Symposium on Measurements & Networking (M&N), 18-20 July 2022, Padua, Italy. SP - 1 EP - 6 PB - IEEE ER - TY - JOUR A1 - Engelmann, Ulrich M. A1 - Pourshahidi, Mohammad Ali A1 - Shalaby, Ahmed A1 - Krause, Hans-Joachim T1 - Probing particle size dependency of frequency mixing magnetic detection with dynamic relaxation simulation JF - Journal of Magnetism and Magnetic Materials N2 - Biomedical applications of magnetic nanoparticles (MNP) fundamentally rely on the particles’ magnetic relaxation as a response to an alternating magnetic field. The magnetic relaxation complexly depends on the interplay of MNP magnetic and physical properties with the applied field parameters. It is commonly accepted that particle core size is a major contributor to signal generation in all the above applications, however, most MNP samples comprise broad distribution spanning nm and more. Therefore, precise knowledge of the exact contribution of individual core sizes to signal generation is desired for optimal MNP design generally for each application. Specifically, we present a magnetic relaxation simulation-driven analysis of experimental frequency mixing magnetic detection (FMMD) for biosensing to quantify the contributions of individual core size fractions towards signal generation. Applying our method to two different experimental MNP systems, we found the most dominant contributions from approx. 20 nm sized particles in the two independent MNP systems. Additional comparison between freely suspended and immobilized MNP also reveals insight in the MNP microstructure, allowing to use FMMD for MNP characterization, as well as to further fine-tune its applicability in biosensing. Y1 - 2022 U6 - https://doi.org/10.1016/j.jmmm.2022.169965 SN - 0304-8853 VL - 563 IS - In progress, Art. No. 169965 PB - Elsevier CY - Amsterdam ER - TY - JOUR A1 - Pourshahidi, Ali Mohammad A1 - Engelmann, Ulrich M. A1 - Offenhäusser, Andreas A1 - Krause, Hans-Joachim T1 - Resolving ambiguities in core size determination of magnetic nanoparticles from magnetic frequency mixing data JF - Journal of Magnetism and Magnetic Materials N2 - Frequency mixing magnetic detection (FMMD) has been widely utilized as a measurement technique in magnetic immunoassays. It can also be used for the characterization and distinction (also known as “colourization”) of different types of magnetic nanoparticles (MNPs) based on their core sizes. In a previous work, it was shown that the large particles contribute most of the FMMD signal. This leads to ambiguities in core size determination from fitting since the contribution of the small-sized particles is almost undetectable among the strong responses from the large ones. In this work, we report on how this ambiguity can be overcome by modelling the signal intensity using the Langevin model in thermodynamic equilibrium including a lognormal core size distribution fL(dc,d0,σ) fitted to experimentally measured FMMD data of immobilized MNPs. For each given median diameter d0, an ambiguous amount of best-fitting pairs of parameters distribution width σ and number of particles Np with R2 > 0.99 are extracted. By determining the samples’ total iron mass, mFe, with inductively coupled plasma optical emission spectrometry (ICP-OES), we are then able to identify the one specific best-fitting pair (σ, Np) one uniquely. With this additional externally measured parameter, we resolved the ambiguity in core size distribution and determined the parameters (d0, σ, Np) directly from FMMD measurements, allowing precise MNPs sample characterization. Y1 - 2022 U6 - https://doi.org/10.1016/j.jmmm.2022.169969 SN - 0304-8853 VL - 563 IS - In progress, Art. No. 169969 PB - Elsevier CY - Amsterdam ER - TY - CHAP A1 - Brauner, Philipp A1 - Vervier, Luisa A1 - Brillowski, Florian A1 - Dammers, Hannah A1 - Steuer-Dankert, Linda A1 - Schneider, Sebastian A1 - Baier, Ralph A1 - Ziefle, Martina A1 - Gries, Thomas A1 - Leicht-Scholten, Carmen A1 - Mertens, Alexander A1 - Nagel, Saskia K. T1 - Organization Routines in Next Generation Manufacturing T2 - Forecasting Next Generation Manufacturing N2 - Next Generation Manufacturing promises significant improvements in performance, productivity, and value creation. In addition to the desired and projected improvements regarding the planning, production, and usage cycles of products, this digital transformation will have a huge impact on work, workers, and workplace design. Given the high uncertainty in the likelihood of occurrence and the technical, economic, and societal impacts of these changes, we conducted a technology foresight study, in the form of a real-time Delphi analysis, to derive reliable future scenarios featuring the next generation of manufacturing systems. This chapter presents the organization dimension and describes each projection in detail, offering current case study examples and discussing related research, as well as implications for policy makers and firms. Specifically, we highlight seven areas in which the digital transformation of production will change how we work, how we organize the work within a company, how we evaluate these changes, and how employment and labor rights will be affected across company boundaries. The experts are unsure whether the use of collaborative robots in factories will replace traditional robots by 2030. They believe that the use of hybrid intelligence will supplement human decision-making processes in production environments. Furthermore, they predict that artificial intelligence will lead to changes in management processes, leadership, and the elimination of hierarchies. However, to ensure that social and normative aspects are incorporated into the AI algorithms, restricting measurement of individual performance will be necessary. Additionally, AI-based decision support can significantly contribute toward new, socially accepted modes of leadership. Finally, the experts believe that there will be a reduction in the workforce by the year 2030. Y1 - 2022 SN - 978-3-031-07734-0 U6 - https://doi.org/10.1007/978-3-031-07734-0_5 SP - 75 EP - 94 PB - Springer CY - Cham ER - TY - CHAP A1 - Mertens, Alexander A1 - Brauner, Philipp A1 - Baier, Ralph A1 - Brillowski, Florian A1 - Dammers, Hannah A1 - van Dyck, Marc A1 - Kong, Iris A1 - Königs, Peter A1 - Kordtomeikel, Frauke A1 - Liehner, Gian Luca A1 - Pütz, Sebastian A1 - Rodermann, Niklas A1 - Schaar, Anne Kathrin A1 - Steuer-Dankert, Linda A1 - Vervier, Luisa A1 - Wlecke, Shari A1 - Gries, Thomas A1 - Leicht-Scholten, Carmen A1 - Nagel, Saskia K. A1 - Piller, Frank T. A1 - Schuh, Günther A1 - Ziefle, Martina A1 - Nitsch, Verena ED - Michael, Judith ED - Pfeiffer, Jérôme ED - Wortmann, Andreas T1 - Modelling Human Factors in Cyber Physical Production Systems by the Integration of Human Digital Shadows T2 - Modellierung 2022 Satellite Events N2 - The future of industrial manufacturing and production will increasingly manifest in the form of cyber-physical production systems. Here, Digital Shadows will act as mediators between the physical and digital world to model and operationalize the interactions and relationships between different entities in production systems. Until now, the associated concepts have been primarily pursued and implemented from a technocentric perspective, in which human actors play a subordinate role, if they are considered at all. This paper outlines an anthropocentric approach that explicitly considers the characteristics, behavior, and traits and states of human actors in socio-technical production systems. For this purpose, we discuss the potentials and the expected challenges and threats of creating and using Human Digital Shadows in production. KW - human digital shadow KW - cyber physical production system KW - human factors Y1 - 2022 U6 - https://doi.org/10.18420/modellierung2022ws-018 N1 - Modellierung 2022, 27. Juni - 01. Juli 2022, Hamburg, Deutschland SP - 147 EP - 149 PB - GI Gesellschaft für Informatik CY - Bonn ER - TY - CHAP A1 - Mertens, Alexander A1 - Pütz, Sebastian A1 - Brauner, Philipp A1 - Brillowski, Florian Sascha A1 - Buczak, Nadine A1 - Dammers, Hannah A1 - van Dyck, Marc A1 - Kong, Iris A1 - Königs, Peter A1 - Kortomeikel, Frauke Carole A1 - Rodemann, Niklas A1 - Schaar, Anne Kathrin A1 - Steuer-Dankert, Linda A1 - Wlecke, Shari A1 - Gries, Thomas A1 - Leicht-Scholten, Carmen A1 - Nagel, Saskia K. A1 - Piller, Frank Thomas A1 - Schuh, Günther A1 - Ziefle, Martina A1 - Nitsch, Verena T1 - Human digital shadow: Data-based modeling of users and usage in the internet of production T2 - 14th Conference Human System Interaction Conference Proceedings N2 - Digital Shadows as the aggregation, linkage and abstraction of data relating to physical objects are a central vision for the future of production. However, the majority of current research takes a technocentric approach, in which the human actors in production play a minor role. Here, the authors present an alternative anthropocentric perspective that highlights the potential and main challenges of extending the concept of Digital Shadows to humans. Following future research methodology, three prospections that illustrate use cases for Human Digital Shadows across organizational and hierarchical levels are developed: human-robot collaboration for manual work, decision support and work organization, as well as human resource management. Potentials and challenges are identified using separate SWOT analyses for the three prospections and common themes are emphasized in a concluding discussion. KW - digital shadow KW - cyber physical production system KW - user & usage KW - internet of production Y1 - 2021 U6 - https://doi.org/10.1109/HSI52170.2021.9538729 N1 - 14th International Conference on Human System Interaction : 8-10 July 2021. Gdańsk, Poland SP - 1 EP - 8 PB - IEEE ER - TY - THES A1 - Steuer-Dankert, Linda T1 - Diversity in complex organizations : the triangle of diversity management, change management and organizational culture from a system-theoretical perspective N2 - Insbesondere im wirtschaftlichen Kontext wird die Diversität von Belegschaften zunehmend als ein kritischer Erfolgsfaktor gesehen. Neben dem Potenzial, welches sich laut Studien aus einem vielfältigen Team ergibt, werden jedoch ebenfalls die aus menschlicher Diversität resultierenden Herausforderungen thematisiert und wissenschaftlich untersucht. Sowohl aus dem Potenzial als auch aus den Herausforderungen ergibt sich dabei die Notwendigkeit der Implementierung eines organisationsspezifischen Diversity Managements, welches die Gewinnung neuer Mitarbeiter*innen einerseits und das Management der vorhandenen Vielfalt andererseits gleichermaßen unterstützt. In der psychologischen, sozial- und wirtschaftswissenschaftlichen Literatur gibt es unterschiedliche Definitionen von Diversität, woraus sich verschiedene Perspektiven auf das Vorgehen bei der Gestaltung und Umsetzung eines Diversity Management Ansatzes ergeben. Insbesondere vor dem Hintergrund der Komplexität des Organisationsumfeldes und der steigenden Anforderungen an die organisationsinterne Agilität besteht die Notwendigkeit, Diversität in Organisationen stärker zu reflektieren und systemspezifische Ansätze zu entwickeln. Dies erfordert die Berücksichtigung organisationsspezifischer Strukturen und Prozesse sowie die Reflexion des Wandels der Organisationskultur durch die Umsetzung eines Diversity Management Ansatzes, der die gegebene Komplexität aufgreift und bewältigen kann. Darüber hinaus sind die psychologischen Auswirkungen solcher Veränderungen auf die Mitarbeiter*innen zu berücksichtigen, um Reaktanzen zu vermeiden und eine nachhaltige Umsetzung von Diversity Management zu ermöglichen. In Ermangelung entsprechender Ansätze im Rahmen öffentlich finanzierter, komplexer Forschungsorganisationen, ist das Ziel dieser Dissertation die Entwicklung und Erprobung eines Forschungsdesigns, welches die Ansätze des Diversity- und Change Managements mit der Organisationskultur verknüpft, indem es eine systemtheoretische Perspektive einnimmt. Dabei wird das Forschungsdesign auf eine komplexe wissenschaftliche Organisation angewendet. Als Basis dient die in Teil A durchgeführte Betrachtung des aktuellen Forschungsstandes aus einer interdisziplinären Perspektive und die damit einhergehende umfassende Einführung in das Forschungsfeld. Im Zuge dessen wird detailliert auf die begriffliche Definition von Diversität eingegangen, bevor dann die psychologischen Konzepte im Diversitätskontext den Übergang zu einer differenzierten Auseinandersetzung mit dem Konzept des Diversity Managements bilden. Auf dieser Grundlage werden das Forschungsdesign sowie die daraus resultierenden Forschungsphasen abgeleitet. Teil A stellt somit die theoretische Grundlage für die in Teil B präsentierten Fachaufsätze dar. Jeder Fachaufsatz beleuchtet dabei in chronologischer Reihenfolge die unterschiedlichen Forschungsphasen. Fachaufsatz I präsentiert den sechsstufigen Forschungsansatz und beleuchtet die besonderen Rahmenbedingungen des Forschungsobjektes aus einer theoretischen Perspektive. Im Anschluss werden die Ergebnisse der Organisationsanalyse, welche zugleich Phase I und II des Forschungskonzeptes darstellen, vorgestellt. Aufbauend auf diesen Forschungsergebnissen fokussiert Forschungsaufsatz II die Darlegung der Ergebnisse aus Forschungsphase III, der Befragung der Führungsebene. Die Befragung thematisierte dabei die Wahrnehmung von Diversity und Diversity Management auf Führungsebene, die Verknüpfung von Diversität mit Innovation sowie die Reflexion des eigenen Führungsstils. Als Ergebnis der Befragung konnten sechs Typen identifiziert werden, die das Führungsverständnis im Diversitätskontext widerspiegeln und somit den Ansatzpunkt für eine top-down gerichtete Diversity Management Strategie darstellen. Darauf aufbauend wird in Forschungsphase IV die Mitarbeiter*innenebene beforscht. Im Zentrum der quantitativen Befragung standen die vorherrschenden Einstellungen zum Themenkomplex Diversity und Diversity Management, die Wahrnehmung von Diversität sowie die Untersuchung des Einflusses der Führungsebene auf die Mitarbeiter*innenebene. Forschungsaufsatz III präsentiert erste Ergebnisse dieser Untersuchung. Die Analyse weist auf eine unterschiedliche Gewichtung der verschiedenen Diversitätskategorien hinsichtlich der Verknüpfung mit Innovationen und somit der Reflexion des Kontextes zwischen Diversität und Innovationen hin. Vergleichbar mit den identifizierten Typen auf der Führungsebene, deutet die Analyse auf die Existenz unterschiedlicher Reflexionsgrade auf Mitarbeiter*innenebene hin. Auf Basis dessen wird im Rahmen von Forschungsaufsatz IV eine nähere Untersuchung des Reflexionsgrades auf Mitarbeiter*innenebene präsentiert und der Diversity Management Ansatz mit Elementen des Change Managements kombiniert. Besondere Berücksichtigung findet als Schlussfolgerung einer theoretischen Analyse die Organisationskultur als zentrales Element bei der Entwicklung und Einführung eines Diversity Management Ansatzes in eine komplexe Forschungsorganisation in Deutschland. Die Analyse zeigt, dass die Wahrnehmung von Diversität heterogen aber zunächst losgelöst vom individuellen Hintergrund ist (im Rahmen dieser Analyse lag der Fokus auf den Diversitätskategorien Gender und Herkunft). Hinsichtlich der Wertschätzung von Diversität zeigt sich dabei ebenfalls ein heterogenes Bild. In der Gesamtbetrachtung stimmen lediglich 17% der Mitarbeiter*innen zu, dass Diversitätskategorien wie Gender, Herkunft oder auch Alter einen Mehrwert darstellen können. Zugleich bewertet diese Gruppe die dem Thema beigemessene Wichtigkeit im CoE als ausreichend. Zusammengefasst lassen sich folgende Erkenntnisse im Rahmen dieser Dissertation ableiten und dienen somit als Grundlage für die Entwicklung eines Diversity Management Ansatzes: (1) Die Entwicklung eines bedarfsorientierten Diversity Management Ansatzes erfordert einen systemtheoretischen Prozess, der sowohl organisationsinterne als auch externe Einflussfaktoren berücksichtigt. Der im Rahmen des Forschungsprojektes entwickelte sechsstufige Forschungsprozess hat sich dabei als geeignetes Instrument erwiesen. (2)Im Rahmen öffentlicher Forschungseinrichtungen lassen sich dabei drei zentrale Faktoren identifizieren: die individuelle Reflexionsebene, die Organisationskultur sowie extern beeinflusste Organisationsstrukturen, Prozesse und Systeme.(3)Vergleichbar mit privatwirtschaftlichen Unternehmen hat auch in wissenschaftlichen Organisationen die Führungsebene einen maßgeblichen Einfluss auf die Wahrnehmung von Diversität und somit einen Einfluss auf die Umsetzung einer Diversity Management Strategie. Daher ist auch im wissenschaftlichen Kontext, bedingt durch die rechtlichen Rahmenbedingungen des Hochschulsystems, ein top-down Ansatz für eine nachhaltige Implementierung erforderlich. (4) Diversity Management steht in einem engen Zusammenhang mit einem organisationalen Wandel, was die Reflexion von Veränderungsprozesse aus einer psychologischen Perspektive erfordert und eine Verknüpfung von Diversity und Change Management bedingt. Aufbauend auf den im Rahmen des entwickelten Forschungskonzeptes gewonnenen zentralen Erkenntnissen wird ein Ansatz entwickelt, der die Ableitung theoretischer Implikationen sowie Implikationen für das Management ermöglicht. Insbesondere vor dem Hintergrund der Reflexion der besonderen Rahmenbedingungen öffentlich finanzierter Forschungsorganisationen werden darüber hinaus politische Implikationen abgeleitet, die auf die Veränderung struktureller Dimensionen abzielen. Y1 - 2020 U6 - https://doi.org/10.18154/RWTH-2020-11830 ER - TY - CHAP A1 - Bauschat, J.-Michael A1 - Benner, Miriam A1 - Klinge, Henner A1 - Ziegler, Simon T1 - Urbane Mobilität entdeckt die 3. Dimension T2 - Transforming Mobility – What Next? N2 - Der Themenkomplex urbane Mobilität ist getrieben durch den Verkehrsinfarkt in Ballungszentren, durch Luftverschmutzung und Lärm, sowie den Trend zum Leben in der Stadt in den städteplanerischen Fokus gerückt. Emissionsneutrale Antriebskonzepte in der Luftfahrt führen zu Ansätzen Fluggeräte einzusetzen, die batteriegetrieben vertikal aufsteigen und landen können. Flugphysikalisch und energetisch ist diese Technik nur dann sinnvoll, wenn es zwingende Gründe gibt (z.B. Rettungseinsätze), daher wird der flugphysikalische Hintergrund prinzipiell erläutert. Es werden einige aktuelle Lufttransportkonzepte für eine urbane Personenbeförderung vorgestellt. Sollte es verstärkt zu Lufttransport über Städten kommen, müssen betroffene Lufträume geordnet und überwacht werden. Wie kompatibel Lufttransportsysteme mit den heute bereits relevanten urbanen Beförderungsmitteln sein müssen, wird kritisch diskutiert. Abschließend werden die Aspekte Akzeptanz durch die Kunden und Wirtschaftlichkeit ebenso angerissen, wie die hochproblematische Rohstoffgewinnung, die Entsorgung und das Recycling von Batterien. Y1 - 2022 SN - 978-3-658-36429-8 U6 - https://doi.org/10.1007/978-3-658-36430-4_53 N1 - Tagungsband zum 13. Wissenschaftsforum Mobilität, Beiträge des Wissenschaftsforums SP - 895 EP - 916 PB - Springer Gabler CY - Wiesbaden ER - TY - CHAP A1 - Hebel, Christoph A1 - Herrmann, Ulf A1 - Ritz, Thomas A1 - Röth, Thilo A1 - Anthrakidis, Anette A1 - Böker, Jörg A1 - Franzke, Till A1 - Grodzki, Thomas A1 - Merkens, Torsten A1 - Schöttler, Mirjam T1 - FlexSHARE – Methodisches Framework zur innovativen Gestaltung der urbanen Mobilität durch Sharing- Angebote T2 - Transforming Mobility – What Next? N2 - Das Ziel des INTERREG-Projektes „SHAREuregio“ (FKZ: 34.EFRE-0300134) ist es, grenzüberschreitende Mobilität in der Euregio Rhein-Maas-Nord zu ermöglichen und zu fördern. Dazu soll ein elektromobiles Car- und Bikesharing- System entwickelt und in der Stadt Mönchengladbach, im Kreis Viersen sowie in den Gemeinden Roermond und Venlo (beide NL) zusammen mit den Partnern Wirtschaftsförderung Mönchengladbach, Wirtschaftsförderung für den Kreis Viersen, NEW AG, Goodmoovs (NL), Greenflux (NL) und der FH Aachen implementiert werden. Zunächst richtet sich das Angebot, bestehend aus 40 Elektroautos und 40 Elektrofahrrädern, an Unternehmen und wird nach einer Erprobungsphase, mit einer größeren Anzahl an Fahrzeugen, auch für Privatpersonen verfügbar gemacht werden. Die Fahrzeuge stehen bei den jeweiligen Anwendungspartnern in Deutschland und den Niederlanden. Im Rahmen dieses Projektes hat die FH Aachen „FlexSHARE“ entwickelt – ein methodisches Framework zur innovativen Gestaltung urbaner Sharing- Angebote. Das Framework ermöglicht es, anhand von messbaren Kenngrößen, bedarfsgerechte und auf die Region abgestimmte Sharing-Systeme zu entwickeln. Y1 - 2022 SN - 978-3-658-36429-8 U6 - https://doi.org/10.1007/978-3-658-36430-4_10 N1 - Tagungsband zum 13. Wissenschaftsforum Mobilität, Beiträge des Wissenschaftsforums SP - 153 EP - 169 PB - Springer Gabler CY - Wiesbaden ER - TY - CHAP A1 - Philipp, Brauner A1 - Brillowski, Florian Sascha A1 - Dammers, Hannah A1 - Königs, Peter A1 - Kordtomeikel, Frauke Carole A1 - Petruck, Henning A1 - Schaar, Anne Kathrin A1 - Schmitz, Seth A1 - Steuer-Dankert, Linda A1 - Mertens, Alexander A1 - Gries, Thomas A1 - Leicht-Scholten, Carmen A1 - Nagel, Saskia K. A1 - Nitsch, Verena A1 - Schuh, Günther A1 - Ziefle, Martina ED - Mrugalska, Beata ED - Trzcielinski, Stefan ED - Karwowski, Waldemar ED - Nicolantonio, Massimo Di ED - Roossi, Emilio T1 - A research framework for human aspects in the internet of production: an intra-company perspective T2 - Proceedings of the AHFE 2020 N2 - Digitalization in the production sector aims at transferring concepts and methods from the Internet of Things (IoT) to the industry and is, as a result, currently reshaping the production area. Besides technological progress, changes in work processes and organization are relevant for a successful implementation of the “Internet of Production” (IoP). Focusing on the labor organization and organizational procedures emphasizes to consider intra-company factors such as (user) acceptance, ethical issues, and ergonomics in the context of IoP approaches. In the scope of this paper, a research approach is presented that considers these aspects from an intra-company perspective by conducting studies on the shop floor, control level and management level of companies in the production area. Focused on four central dimensions—governance, organization, capabilities, and interfaces—this contribution presents a research framework that is focused on a systematic integration and consideration of human aspects in the realization of the IoP. KW - Human factors KW - Digitalization KW - Acceptance KW - Ethics KW - Human-robot collaboration Y1 - 2020 SN - 978-3-030-51980-3 U6 - https://doi.org/10.1007/978-3-030-51981-0_1 N1 - AHFE 2020 Virtual Conferences on Human Aspects of Advanced Manufacturing, Advanced Production Management and Process Control, and Additive Manufacturing, Modeling Systems and 3D Prototyping, July 16–20, 2020, USA SP - 3 EP - 17 PB - Springer CY - Cham ER - TY - CHAP A1 - von den Driesch, Elena A1 - Steuer-Dankert, Linda A1 - Berg, Tobias A1 - Leicht-Scholten, Carmen T1 - Implementation of gender and diversity perspectives in transport development plans in germany T2 - Engendering cities: designing sustainable urban spaces for all N2 - As mobility should ensure the accessibility to and participation in society, transport planning has to deal with a variety of gender and diversity categories affecting users’ mobility needs and patterns. Exemplified by an analysis of an instrument of transport development processes – German Transport Development Plans (TDPs) – we investigated to what extent diverse target groups and their mobility requirements are implemented in transport strategy papers. Research results illustrate a still-prevalent neglect of several relevant gender and diversity categories while prioritizing and focusing on eco-friendly topics. But how sustainable can transport be without facing the diversification of life circumstances? Y1 - 2020 SN - 978-1-351-20090-5 SP - 90 EP - 109 PB - Routledge CY - London ER - TY - CHAP A1 - Leicht-Scholten, Carmen A1 - Steuer-Dankert, Linda T1 - Educating engineers for socially responsible solutions through design thinking T2 - Design thinking in higher education: interdisciplinary encounters N2 - There is a broad international discussion about rethinking engineering education in order to educate engineers to cope with future challenges, and particularly the sustainable development goals. In this context, there is a consensus about the need to shift from a mostly technical paradigm to a more holistic problem-based approach, which can address the social embeddedness of technology in society. Among the strategies suggested to address this social embeddedness, design thinking has been proposed as an essential complement to engineering precisely for this purpose. This chapter describes the requirements for integrating the design thinking approach in engineering education. We exemplify the requirements and challenges by presenting our approach based on our course experiences at RWTH Aachen University. The chapter first describes the development of our approach of integrating design thinking in engineering curricula, how we combine it with the Sustainable Development Goals (SDG) as well as the role of sustainability and social responsibility in engineering. Secondly, we present the course “Expanding Engineering Limits: Culture, Diversity, and Gender” at RWTH Aachen University. We describe the necessity to theoretically embed the method in social and cultural context, giving students the opportunity to reflect on cultural, national, or individual “engineering limits,” and to be able to overcome them using design thinking as a next step for collaborative project work. The paper will suggest that the successful implementation of design thinking as a method in engineering education needs to be framed and contextualized within Science and Technology Studies (STS). Y1 - 2020 SN - 978-981-15-5780-4 U6 - https://doi.org/10.1007/978-981-15-5780-4 SP - 229 EP - 246 PB - Springer CY - Singapore ER - TY - CHAP A1 - Steuer-Dankert, Linda A1 - Leicht-Scholten, Carmen ED - Tipurić, Darko ED - Hruška, Domagoj T1 - Diversity- and innovation management in complex engineering organizations T2 - 7th International OFEL Conference on Governance, Management and Entrepreneurship: Embracing Diversity in Organisations. April 5th - 6th, 2019, Dubrovnik, Croatia N2 - Diversity is increasingly being addressed as an innovation-promoting factor. For this reason, companies and institutions tackle the integration of a diversity management approach that enables a heterogenic perspective on innovation development. However, system-theoretical frameworks state that the implementation of diversity measures that are not tailored to the needs of the organization often leads to a rejection or reactivity with regard to the management approach. In this context, especially organizations, which are characterized by a specific hierarchical structure, a dominant habitus or specialist culture, must face the challenge of realizing a sustainable change of the corporate culture that sets the basis for implementing diversity management approaches. The presented research project focuses on analyzing the situation in a huge scientific collaborative project - so called Cluster of Excellence (CoE) - with the aim to implement a diversity - and innovation management strategy. Considering the influencing determinants, the CoE is characterized by its embeddedness in the scientific system, a complex organizational structure, and a high fluctuation rate. The paper presents a systemic approach of reflecting these factors in order to develop a diversity- and innovation management strategy. In this frame, the results of a quantitative survey of CoE employees and derived mindset-types are presented. The results show a need for taking different mindset-types into account, to be able to develop a tailored management strategy. The aim of the project is to give recommendations for developing a sustainable management concept that promotes both diversity and innovation by drawing on the persisting mindsets of organization members while reflecting top down as well as bottom up factors of implementation processes as well as the psychology of change. This paper addresses all who are concerned with the management of human resources in innovation processes and are striving for a cultural change within the framework of complex organizations. KW - Change Management KW - Corporate Culture KW - Diversity Management KW - Engineering KW - Innovation Management Y1 - 2019 SP - 136 EP - 157 PB - Governance Research and Development Centre (CIRU) CY - Zagreb ER - TY - JOUR A1 - Steuer-Dankert, Linda A1 - Gilmartin, Shannon K. A1 - Muller, Carol B. A1 - Dungs, Carolin A1 - Sheppard, Sheri A1 - Leicht-Scholten, Carmen T1 - Expanding engineering limits : a concept for socially responsible education of engineers JF - The international journal of engineering education Y1 - 2019 SN - 0949-149X VL - 35 IS - 2 SP - 658 EP - 673 ER - TY - CHAP A1 - Müller-Abdelrazeq, Sarah Luisa A1 - Brauner, Philipp A1 - Calero Valdez, André A1 - Jansen, Ulrich A1 - Platte, Laura A1 - Schaar, Anne-Kathrin A1 - Steuer-Dankert, Linda A1 - Zachow, Sebastian A1 - Schönefeld, Kathrin A1 - Haberstroh, Max A1 - Leicht-Scholten, Carmen A1 - Ziefle, Martina ED - Pather, Shaun T1 - Interdisciplinary cooperation management in research clusters: a review of twelve years. T2 - Proceedings of the 15th International Conference on Intellectual Capital, Knowledge Management & Organisational Learning N2 - As an interdisciplinary research network, the Cluster of Excellence “Integrative Production Technology for High-Wage Countries” (CoE) comprises of around 150 researchers. Their scientific background ranges from mechanical engineering and computer science to social sciences such as sociology and psychology. In addition to content- and methodbased challenges, the CoE’s employees are faced with heterogenic organizational cultures, different hierarchical levels, an imbalanced gender distribution, and a high employee fluctuation. The sub-project Scientific Cooperation Engineering 1 (CSP1) addresses the challenge of interdisciplinary cooperation and organizational learning and aims at fostering interdisciplinarity and its synergies as a source of innovation. Therefore, the project examines means of reaching an organizational development, ranging from temporal structures to a sustainable network in production technology. To achieve this aim, a broad range of means has been developed during the last twelve years: In addition to physical measures such as regular network events and trainings, virtual measures such as the Terminology App were focused. The app is an algorithmic analysis method for uncovering latent topic structures of publications of the CoE to highlight thematic intersections and synergy potentials. The detection and promotion of has been a vital and long known element in knowledge management. Furthermore, CSP1 focusses on project management and thus developed evaluation tools to measure and control the success of interdisciplinary cooperation. In addition to the cooperation fostering measures, CSP1 conducted studies about interdisciplinarity and diversity and their relationship with innovation. The scientific background of these means and the research results of CSP1 are outlined in this paper to offer approaches for successful interdisciplinary cooperation management. Y1 - 2018 SN - 978-1-912764-09-9 N1 - hosted by University of the Western Cape, South Africa 29-30 November 2018 SP - 216 EP - 224 PB - ACPIL ER - TY - JOUR A1 - Steuer-Dankert, Linda A1 - Sharma, Mamta Rameshwarlal A1 - Bleck, Wolfgang A1 - Leicht-Scholten, Carmen T1 - Diversity and innovation management in large research groups JF - International Journal of Innovation Management N2 - Contemporary research appreciates a diverse workforce as a potential source of innovation. Researchers explore the fine details of why diversity management is central for generating innovations in heterogeneous research groups and how it could be effectively implemented into organizations. Complex research associations that discuss topics with a high impact on society increasingly address the necessity of establishing a diverse workforce to confront the challenges of tomorrow. Characterized by complex management structures as well as hierarchies, research associations have not been a subject of investigation until now. For this reason, the presented research project aims to develop a diversity and innovation management strategy with the ultimate goal of inducing change in the corporate culture. The proposed approach consisted of six phases; the first two phases investigated the status quo of diversity in the existing organizational structures of member institutes and the variety of particular working cultures within the research association. The third and the fourth phases utilized qualitative and quantitative studies. The third phase focused on the connection of management level to diversity and innovation, and the need for diversity and innovation management, and tailor-made methods of implementing them. The first three phases have been accomplished successfully; preliminary results are already available. The fourth phase will mainly focus on exploring the mind-set of the employees. The fifth phase will consolidate the findings in the first four phases into an implementable strategy. The final phase will address the implementation of this strategy into the organization. Phases 4 to 6 have not yet been undertaken KW - diversity management KW - innovation management KW - research association KW - change management KW - engineering Y1 - 2017 SN - 1757-5877 VL - 5 IS - 2 SP - 49 EP - 72 ER - TY - CHAP A1 - Zähl, Philipp M. A1 - Biewendt, Marcel A1 - Wolf, Martin A1 - Eggert, Mathias T1 - Requirements for competence developing games in the environment of SE Competence Development T2 - AKWI-Tagungsband zur 35. AKWI-Jahrestagung N2 - Many of today’s factors make software development more and more complex, such as time pressure, new technologies, IT security risks, et cetera. Thus, a good preparation of current as well as future software developers in terms of a good software engineering education becomes progressively important. As current research shows, Competence Developing Games (CDGs) and Serious Games can offer a potential solution. This paper identifies the necessary requirements for CDGs to be conducive in principle, but especially in software engineering (SE) education. For this purpose, the current state of research was summarized in the context of a literature review. Afterwards, some of the identified requirements as well as some additional requirements were evaluated by a survey in terms of subjective relevance. KW - software engineering KW - requirements KW - competence developing games KW - systematic literature review Y1 - 2022 SN - 978-3-95545-409-8 U6 - https://doi.org/10.30844/AKWI_2022_05 N1 - Tagungsband zur 35. Jahrestagung des Arbeitskreises Wirtschaftsinformatik an Hochschulen für Angewandte Wissenschaften im deutschsprachigen Raum (AKWI), 11.09. bis 13.09.2022, Hochschule für Technik und Wirtschaft Berlin (HTW Berlin) und Hochschule für Wirtschaft und Recht Berlin (HWR Berlin) SP - 73 EP - 88 PB - GITO CY - Berlin ER - TY - CHAP A1 - Steuer-Dankert, Linda A1 - Leicht-Scholten, Carmen T1 - Innovation and Diversity : Integrating new perspectives into research associations T2 - 12th European Conference on Innovation and Entrepreneurship (ECIE 2017) : Paris, France, 21-22 September 2017 N2 - The link between diversity and innovation is broadly discussed in the context of research and innovation processes. Many institutions and enterprises, specifically in commerce, have already tried to establish sustainable diversity management concepts, in order to increase the diversity of their workforce in addition to establishing a corporate culture of openness. Alongside the creation of a working place where different experiences and skills are valued equally, the entrepreneurial intention is to transfer diversity into economically relevant advantages. Taking into account the potential of diversity in research and innovation processes, the project “Diversity- and Innovation Management” was incorporated within a large interdisciplinary research Cluster. The project’s purpose was to study the context between diversity and innovation in research associations and to later develop a customised management concept into an interdisciplinary research Cluster on integrative production technology with full integration. The challenge of such research associations lays in an organisational structure which is often described as being decentralised. Researchers coming from different academic disciplines, while having diverse habits, conduct research on large scientific issues and challenges. In addition, these researchers are socialised in different institutions and university chairs. Theses differences in leadership styles, business cultures and organisational strategies, follow into their research team work. Taking a closer look into the management of human resources suggests that decentral organised recruitment processes, as well as allocation of human resources, lead to a lacking overview in regard to missing competencies, perspectives and backgrounds in research networks. These circumstances are comparable to big corporate groups. While developing a management concept for research associations, these characteristics must be considered. To ensure this, the project follows a human-centred approach, which considers top-down, as well as bottom-up perspectives. This paper presents the applied mixed-method approach in the scientific issue described above. In the frame of the Cluster of Excellence “Integrative Production Technology for High-Wage Countries” research results based on quantitative, as well as qualitative studies, were presented as an application example. This paper provides a new perspective on the innovation and diversity context. Against the background of complex research organisations, the development approach of a management concept is particularly interesting. KW - Innovation KW - Diversity KW - Innovation Management KW - Diversity Management KW - Leadership Y1 - 2017 SN - 978-1-911218-54-8 SP - 767 EP - 776 ER - TY - CHAP A1 - Steuer-Dankert, Linda A1 - Bouffier, Anna A1 - Gaedicke, Sonja A1 - Leicht-Scholten, Carmen T1 - Diversifying engineering education: a transdisciplinary approach from RWTH Aachen University T2 - Strategies for increasing diversity in engineering majors and careers N2 - Engineers and therefore engineering education are challenged by the increasing complexity of questions to be answered globally. The education of future engineers therefore has to answer with curriculums that build up relevant skills. This chapter will give an example how to bring engineering and social responsibility successful together to build engineers of tomorrow. Through the integration of gender and diversity perspectives, engineering research and teaching is expanded with new perspectives and contents providing an important potential for innovation. Aiming on the enhancement of engineering education with distinctive competencies beyond technical expertise, the teaching approach introduced in the chapter represents key factors to ensure that coming generations of engineers will be able to meet the requirements and challenges a changing globalized world holds for them. The chapter will describe how this approach successfully has been implemented in the curriculum in engineering of a leading technical university in Germany. Y1 - 2017 SN - 9781522522126 U6 - https://doi.org/10.4018/978-1-5225-2212-6.ch010 SP - 201 EP - 235 PB - IGI Global CY - Hershey, USA ER - TY - CHAP A1 - Steuer-Dankert, Linda A1 - Leicht-Scholten, Carmen T1 - Social responsibility and innovation - Key competencies for engineers T2 - ICERI 2016: 9th International Conference of Education, Research and Innovation: Conference Proceedings : Seville (Spain), 14-16 November N2 - Engineers are of particular importance for the societies of tomorrow. The big social challenges society has to cope with in future, can only be mastered, if engineers link the development and innovation process closely with the requirements of people. As a result, in the frame of the innovation process engineers have to design and develop products for diverse users. Therefore, the consideration of diversity in this process is a core competence engineers should have. Implementing the consideration of diverse requirements into product design is also linked to the development of sustainable products and thus leads to social responsible research and development, the core concept formulated by the EU. For this reason, future engineers should be educated to look at the technical perspectives of a problem embedded in the related questions within societies they are developing their artefacts for. As a result, the aim of teaching engineering should be to prepare engineers for these requirements and to draw attention to the diverse needs in a globalized world. To match the competence profiles of future engineers to the global challenges and the resulting social responsibility, RWTH Aachen University, one of the leading technical universities in Germany, has established the bridging professorship “Gender and Diversity in Engineering” (GDI) which educates engineers with an interdisciplinary approach to expand engineering limits. The interdisciplinary teaching concept of the research group pursues an approach which imparts an application oriented Gender and Diversity expertise to future engineers. In the frame of an established teaching concept, which is a result of experiences and expertise of the research group, students gain theoretical knowledge about Gender and Diversity and learn how to transfer their knowledge into their later field of action. In the frame of the conference the institutional approach will be presented as well as the teaching concept which will be introduced by concrete course examples. KW - diversity KW - innovation KW - social responsible engineering KW - engineering education Y1 - 2016 SN - 978-84-617-5895-1 U6 - https://doi.org/10.21125/iceri.2016.0353 SN - 2340-1095 SP - 5967 EP - 5976 ER - TY - CHAP A1 - Leicht-Scholten, Carmen A1 - Steuer-Dankert, Linda A1 - Bouffier, Anna T1 - Facing Future Challenges: Building Engineers for Tomorrow T2 - Conference proceedings : new perspectives in science education : 5th Conference edition, Florence, Italy, 17-18 March 2016 N2 - Future engineers are increasingly confronted with the so-called Megatrends which are the big social challenges society has to cope with. These Megatrends, such as “Silver Society”, “Globalization”, “Mobility” and “Female Shift” require an application-oriented perspective on Diversity especially in the engineering field. Therefore, it is necessary to enable future engineers not only to look at the technical perspectives of a problem, but also to be able to see the related questions within societies they are developing their artefacts for. The aim of teaching engineering should be to prepare engineers for these requirements and to draw attention to the diverse needs in a globalized world. Bringing together technical knowledge and social competences which go beyond a mere training of the so-called “soft skills”, is a new approach followed at RWTH Aachen University, one of the leading technical universities in Germany. RWTH Aachen University has established the bridging professorship “Gender and Diversity in Engineering” (GDI) which educates engineers with an interdisciplinary approach to expand engineering limits. In the frame of a sustainable teaching concept the research group under the leadership of Prof. Carmen Leicht-Scholten has developed an approach which imparts a supplication-specific Gender and Diversity expertise to engineers. In workshops students gain theoretical knowledge about Gender and Diversity and learn how to transfer their knowledge in their special field of study and later work. To substantiate this, the course participants have to solve case studies from real life. The cases which are developed in collaboration with non-profit organizations and enterprises from economy rise the students to challenges which are inspired by professional life. Evaluation shows the success of this approach as well as an increasing demand for such teaching formats. KW - Diversity KW - Engineering Education KW - Gender KW - Higher Education Y1 - 2016 SN - 978-886292-705-5 SP - 32 EP - 37 ER - TY - CHAP A1 - Steuer-Dankert, Linda A1 - Berg, Tobias A1 - Leicht-Scholten, Carmen T1 - Breaking the habit – new approaches in engineering education T2 - Proceedings of the 43rd Annual Conference of the European Society for Engineering Education N2 - Within the framework of the project a genderand diversity-oriented teaching evaluation and modern, media-supported blended learning approaches were used in order to achieve the intended goals. First research results of the literature and status quo analysis were already implemented and tested in newly designed teaching approaches, for example in a multidisciplinary introductory lecture of civil engineering at RWTH Aachen University. KW - teaching KW - engineering education KW - gender and diversity KW - best practice Y1 - 2015 SN - 978-2-87352-012-0 N1 - Annual Conference of the European Society for Engineering Education , Orléans , France , SEFI , 2015-06-29 - 2015-07-02 ER - TY - CHAP A1 - Stangel-Meseke, Martina A1 - Hahn, Pia A1 - Steuer-Dankert, Linda T1 - Ausblick: Der individualitätsbezogene Diversity Management-Ansatz als Antwort auf Individualisierung T2 - Diversity Management und Individualisierung N2 - Der Megatrend Individualisierung fordert von Unternehmen, ihre Strategien und Prozessabläufe bei zunehmender Globalisierung grundlegend zu überdenken. Während Strategien und Prozessabläufe im Unternehmen Standards unterliegen, entwickelt sich unsere Gesellschaft immer stärker zu einem individuumszentrierten System, in dem es gilt, Werte und Lebensstile der Individuen zu berücksichtigen und derart wertzuschätzen, dass Mitarbeitende motiviert und mit hoher Bindung an das Unternehmen die anstehenden Leistungen für das Unternehmen erbringen. Im Konzept DiM sind Standardisierung und Individualisierung keine gegensätzlichen Aspekte, da bei DiM neben der Betrachtung des betriebswirtschaftlichen Nutzens dieses Konzepts für Unternehmen die Wertschätzung des Individuums als genuines Merkmal betont wird. Y1 - 2015 SN - 978-3-658-07485-2 SP - 23 EP - 24 PB - Springer Gabler CY - Wiesbaden ER - TY - CHAP A1 - Stangel-Meseke, Martina A1 - Hahn, Pia A1 - Steuer-Dankert, Linda T1 - Der Individualisierungs-Trend prägt die Unternehmenszukunft T2 - Diversity Management und Individualisierung N2 - Laut Zukunftsinstitut (2010) stellt die Individualisierung eine langfristige und nachhaltige Veränderung dar, die die gesamte Gesellschaft (den einzelnen Menschen, Unternehmen, den Staat) betrifft und Auswirkungen auf nahezu alle Lebensbereiche (z. B. Arbeit, Wohnen, Partnerschaft) hat. Die Individualisierung beschreibt dabei die Entwicklung hin zur Fokussierung persönlicher Interessen und Lebensentscheidungen der einzelnen Person (Kunze, Individualisierung, 2011). Der Grund für diese Entwicklung sind laut Kunze (Individualisierung, 2011) Treiber wie steigendes Vermögen, Bildung und Mobilität, was die einzelne Person unabhängiger von größeren Gemeinschaften macht und mehr Freiheit zur Selbstverwirklichung bietet. Als eine Konsequenz daraus werden Wertevorstellungen nicht mehr einfach hingenommen, sondern für die eigene Person überprüft und individualisiert (Kunze, Individualisierung, 2011). So wies Beck bereits 1996 darauf hin, dass Individualisierung meint „erstens die Auflösung und zweitens die Ablösung industriegesellschaftlicher Lebensformen durch andere, in denen die Einzelnen ihre Biographie selbst herstellen, inszenieren, zusammenflickschustern müssen“ (Beck, Die Erfindung des Politischen, 1996, S. 150). Y1 - 2015 SN - 978-3-658-07484-5 U6 - https://doi.org/10.1007/978-3-658-07485-2_1 SP - 1 EP - 3 PB - Springer Gabler CY - Wiesbaden ER - TY - CHAP A1 - Stangel-Meseke, Martina A1 - Hahn, Pia A1 - Steuer-Dankert, Linda T1 - Balance durch Diversity Management : Lösungsansätze für unternehmerische Herausforderungen aus Megatrends T2 - Balance Management N2 - Unsere unternehmerische Umwelt befindet sich in einem zunehmend dynamischen Wandel. Dies führt dazu, dass Herausforderungen, denen sich Unternehmen stellen müssen, immer komplexer werden. Hier gilt es zunehmend, eine Balance zwischen verschiedenen Spannungsfeldern zu erreichen. Sogenannte Megatrends stellen die Treiber dieses Wandels dar. Als Megatrend werden nach dem Zukunftsinstitut (2010a) richtungsweisende Veränderungstendenzen aufgefasst, die alle Bereiche des Lebens sowohl individuell als auch gesellschaftlich beeinflussen und langfristige Auswirkungen haben. Y1 - 2013 SN - 978-3-658-02191-7 U6 - https://doi.org/10.1007/978-3-658-02192-4_6 SP - 145 EP - 166 PB - Springer Gabler CY - Wiesbaden ER - TY - JOUR A1 - Falkenberg, Fabian A1 - Rahba, Jade A1 - Fischer, David A1 - Bott, Michael A1 - Bongaerts, Johannes A1 - Siegert, Petra T1 - Biochemical characterization of a novel oxidatively stable, halotolerant, and high-alkaline subtilisin from Alkalihalobacillus okhensis Kh10-101T JF - FEBS Open Bio N2 - Halophilic and halotolerant microorganisms represent a promising source of salt-tolerant enzymes suitable for various biotechnological applications where high salt concentrations would otherwise limit enzymatic activity. Considering the current growing enzyme market and the need for more efficient and new biocatalysts, the present study aimed at the characterization of a high-alkaline subtilisin from Alkalihalobacillus okhensis Kh10-101T. The protease gene was cloned and expressed in Bacillus subtilis DB104. The recombinant protease SPAO with 269 amino acids belongs to the subfamily of high-alkaline subtilisins. The biochemical characteristics of purified SPAO were analyzed in comparison with subtilisin Carlsberg, Savinase, and BPN'. SPAO, a monomer with a molecular mass of 27.1 kDa, was active over a wide range of pH 6.0–12.0 and temperature 20–80 °C, optimally at pH 9.0–9.5 and 55 °C. The protease is highly oxidatively stable to hydrogen peroxide and retained 58% of residual activity when incubated at 10 °C with 5% (v/v) H2O2 for 1 h while stimulated at 1% (v/v) H2O2. Furthermore, SPAO was very stable and active at NaCl concentrations up to 5.0 m. This study demonstrates the potential of SPAO for biotechnological applications in the future. KW - Alkalihalobacillus okhensis KW - detergent protease KW - halotolerant protease KW - high-alkaline subtilisin KW - oxidative stable protease Y1 - 2022 U6 - https://doi.org/10.1002/2211-5463.13457 SN - 2211-5463 N1 - Corresponding author: Petra Siegert VL - 12 IS - 10 SP - 1729 EP - 1746 PB - Wiley CY - Hoboken, NJ ER - TY - JOUR A1 - Monakhova, Yulia A1 - Diehl, Bernd W.K. T1 - Nuclear magnetic resonance spectroscopy as an elegant tool for a complete quality control of crude heparin material JF - Journal of Pharmaceutical and Biomedical Analysis N2 - Nuclear magnetic resonance (NMR) spectrometric methods for the quantitative analysis of pure heparin in crude heparin is proposed. For quantification, a two-step routine was developed using a USP heparin reference sample for calibration and benzoic acid as an internal standard. The method was successfully validated for its accuracy, reproducibility, and precision. The methodology was used to analyze 20 authentic porcine heparinoid samples having heparin content between 4.25 w/w % and 64.4 w/w %. The characterization of crude heparin products was further extended to a simultaneous analysis of these common ions: sodium, calcium, acetate and chloride. A significant, linear dependence was found between anticoagulant activity and assayed heparin content for thirteen heparinoids samples, for which reference data were available. A Diffused-ordered NMR experiment (DOSY) can be used for qualitative analysis of specific glycosaminoglycans (GAGs) in heparinoid matrices and, potentially, for quantitative prediction of molecular weight of GAGs. NMR spectrometry therefore represents a unique analytical method suitable for the simultaneous quantitative control of organic and inorganic composition of crude heparin samples (especially heparin content) as well as an estimation of other physical and quality parameters (molecular weight, animal origin and activity). KW - NMR spectroscopy KW - Heparin KW - Crude heparin KW - USP KW - Ions Y1 - 2022 U6 - https://doi.org/10.1016/j.jpba.2022.114915 SN - 0731-7085 VL - 219 IS - Article number: 114915 PB - Elsevier CY - New York, NY ER - TY - JOUR A1 - Cheenakula, Dheeraja A1 - Hoffstadt, Kevin A1 - Krafft, Simone A1 - Reinecke, Diana A1 - Klose, Holger A1 - Kuperjans, Isabel A1 - Grömping, Markus T1 - Anaerobic digestion of algal–bacterial biomass of an Algal Turf Scrubber system JF - Biomass Conversion and Biorefinery N2 - This study investigated the anaerobic digestion of an algal–bacterial biofilm grown in artificial wastewater in an Algal Turf Scrubber (ATS). The ATS system was located in a greenhouse (50°54′19ʺN, 6°24′55ʺE, Germany) and was exposed to seasonal conditions during the experiment period. The methane (CH4) potential of untreated algal–bacterial biofilm (UAB) and thermally pretreated biofilm (PAB) using different microbial inocula was determined by anaerobic batch fermentation. Methane productivity of UAB differed significantly between microbial inocula of digested wastepaper, a mixture of manure and maize silage, anaerobic sewage sludge, and percolated green waste. UAB using sewage sludge as inoculum showed the highest methane productivity. The share of methane in biogas was dependent on inoculum. Using PAB, a strong positive impact on methane productivity was identified for the digested wastepaper (116.4%) and a mixture of manure and maize silage (107.4%) inocula. By contrast, the methane yield was significantly reduced for the digested anaerobic sewage sludge (50.6%) and percolated green waste (43.5%) inocula. To further evaluate the potential of algal–bacterial biofilm for biogas production in wastewater treatment and biogas plants in a circular bioeconomy, scale-up calculations were conducted. It was found that a 0.116 km2 ATS would be required in an average municipal wastewater treatment plant which can be viewed as problematic in terms of space consumption. However, a substantial amount of energy surplus (4.7–12.5 MWh a−1) can be gained through the addition of algal–bacterial biomass to the anaerobic digester of a municipal wastewater treatment plant. Wastewater treatment and subsequent energy production through algae show dominancy over conventional technologies. KW - Biogas KW - Methane KW - Algal Turf Scrubber KW - Algal–bacterial bioflm KW - Circular bioeconomy Y1 - 2022 U6 - https://doi.org/10.1007/s13399-022-03236-z SN - 2190-6823 N1 - Corresponding author: Dheeraja Cheenakula VL - 13 SP - 15 Seiten PB - Springer CY - Berlin ER - TY - CHAP A1 - Weiss, Christian A1 - Heslenfeld, Jonas A1 - Saewe, Jasmin Kathrin A1 - Bremen, Sebastian A1 - Häfner, Constantin Leon T1 - Investigation on the influence of powder humidity in Laser Powder Bed Fusion (LPBF) T2 - Procedia CIRP 12th CIRP Conference on Photonic Technologies [LANE 2022] N2 - In the Laser Powder Bed Fusion (LPBF) process, parts are built out of metal powder material by exposure of a laser beam. During handling operations of the powder material, several influencing factors can affect the properties of the powder material and therefore directly influence the processability during manufacturing. Contamination by moisture due to handling operations is one of the most critical aspects of powder quality. In order to investigate the influences of powder humidity on LPBF processing, four materials (AlSi10Mg, Ti6Al4V, 316L and IN718) are chosen for this study. The powder material is artificially humidified, subsequently characterized, manufactured into cubic samples in a miniaturized process chamber and analyzed for their relative density. The results indicate that the processability and reproducibility of parts made of AlSi10Mg and Ti6Al4V are susceptible to humidity, while IN718 and 316L are barely influenced. KW - LPBF KW - Additive Manufacturing KW - Powder Material KW - Humidity Y1 - 2022 U6 - https://doi.org/10.1016/j.procir.2022.08.102 SN - 2212-8271 N1 - 12th CIRP Conference on Photonic Technologies [LANE 2022], 04. September 2022 bis 08. September 2022, Fürth VL - 111 SP - 115 EP - 120 PB - Elsevier CY - Amsterdam ER - TY - CHAP A1 - Eggert, Mathias A1 - Dyong, Julian T1 - Applying process mining in small and medium sized IT enterprises – challenges and guidelines T2 - Business Process Management, 20th International Conference, BPM 2022, Proceedings N2 - Process mining gets more and more attention even outside large enterprises and can be a major benefit for small and medium sized enterprises (SMEs) to gain competitive advantages. Applying process mining is challenging, particularly for SMEs because they have less resources and process maturity. So far, IS researchers analyzed process mining challenges with a focus on larger companies. This paper investigates the application of process mining by means of a case study and sheds light into the particular challenges of an IT SME. The results reveal 13 SME process mining challenges and seven guidelines to address them. In this way, the paper contributes to the understanding of process mining application in SME and shows similarities and differences to larger companies. KW - Process mining KW - Challenges KW - Guidelines KW - SME KW - Case Study Y1 - 2022 SN - 978-3-031-16103-2 U6 - https://doi.org/10.1007/978-3-031-16103-2_11 N1 - International Conference on Business Process Management (BPM 2022), Münster, Germany, Sept. 11-16, 2022 SP - 125 EP - 142 PB - Springer CY - Cham ER - TY - THES A1 - Christiani, Fabian T1 - Nachhaltiger Bauen : eine interaktive Plattform zum Vergleich von Baustoffen N2 - Bei dem Projekt „Nachhaltiger Bauen – Eine interaktive Plattform zum Vergleich von Baustoffen“ handelt es sich um eine Datenbank, die verschiedene Baustoffe mit deren Eigenschaften listet und einen Vergleich dieser ermöglicht. Das Baugewerbe trägt einen erheblichen Teil zum Klimawandel bei. Besonders der CO2-Ausstoß, der Ressourcenverbrauch und die Abfallproduktion sind hier zu nennen. Deshalb ist der Aspekt der Nachhaltigkeit von zentraler Bedeutung für die Zukunft der Baubranche.Ziel des Projekts ist es, sowohl die technischen als auch die ökologischen Eigenschaften von Baustoffen darzustellen und miteinander zu vergleichen. So kann die Plattform aktiv und effektiv gegen die umwelttechnischen Probleme der Baubranche wirken. KW - Nachhaltigkeit KW - Bauwesen KW - Baustoffe KW - Zukunft KW - Ökologie Y1 - 2022 PB - FH Aachen CY - Aachen ER - TY - THES A1 - Crott, Anne T1 - Textil- und Industriemuseum (TIM) Augsburg : Entwicklung eines neuen Erscheinungsbildes N2 - Die Stadt Augsburg war eine der größten Textilstädte Europas. Seit 2010 präsentiert das Textil- und Industriemuseum (TIM) eine Vielzahl von Exponaten in der alten Kammgarnspinnerei im ehemaligen Augsburger Textilviertel und ist somit ein wichtiger Bestandteil der bayrischen Museumslandschaft und deutschen Textilgeschichte. Neben seiner besonderen Lage überzeugt das TIM vor allem mit einer großen Musterbuchsammlung. Im Fokus des in dieser Arbeit neugestalteten Erscheinungsbildes stehen die verschiedenen Muster, die den textilen Schwerpunkt in den Vordergrund rücken und dem Museum damit einen einprägsamen Wiedererkennungswert geben. Mithilfe des neuen Corporate Designs soll das Museum für regionale und überregionale Besucher:innen attraktiver gemacht und somit die einmalige geschichtliche Bedeutung vermittelt und erhalten werden. KW - Corporate Design KW - TIM KW - Mode KW - Textil KW - Augsburg Y1 - 2022 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER - TY - THES A1 - Cekic, Dilara T1 - Visionsbild eines BMW AG internen Tools : Optimierung einer datenzentrierten Plattform der BMW AG N2 - Die BMW AG verfolgt mehrere Ansätze eine optimierte Effizienzsteigerung durch eigens entwickelte Softwaretools zu erreichen. Der Fokus hierbei liegt in der Ermöglichung einer datenzentrierten, nutzerorientierten und hochautomatisierten Fahrzeugentwicklung. Das eigen von der BMW AG entwickelte Software-Tool „Parts List“ dient als digitale Bauteilliste für Entwicklungsteams. Das Tool bündelt mehrere Datenbanken und stellt diese in Echtzeit zur Verfügung. Somit kann der manuelle Pflegeaufwand erheblich reduziert und eine Durchgängigkeit einer Vielzahl von Daten ermöglicht werden. Der Fokus der Abschlussarbeit liegt in der konzeptionellen und gestalterischen Optimierung des Tools. Dabei wird insbesondere der User Centered Design Prozess betrachtet, bei dem die Nutzer bzw. die Entwicklungsteams im Zentrum stehen. KW - UX/UI Design KW - Nutzeroberfläche KW - BMW AG KW - Softwarentwicklung Y1 - 2022 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER - TY - THES A1 - Buhr, Amelie T1 - Entschleunigen : warum unser Modekonsum verlangsamt werden muss N2 - In Zeiten von Schnelllebigkeit ändern immer mehr Menschen bewusst ihren Umgang mit alltäglichen Dingen. Was dabei häufig in den Hintergrund rückt, ist das Thema "bewusste Kleidung". Beeinflusst durch sogenannte Fast-Fashion-Modeketten und Social Media leben wir in einer regelrechten Wegwerfgesellschaft. „Entschleunigen“ beschäftigt sich mit den Schattenseiten der Modeindustrie, zeigt aber ebenso (neue) Wege auf, die auf eine bessere Zukunft für uns und unsere Umwelt hoffen lassen. Aufgeteilt in zwei Kapitel gibt „Entschleunigen“ einen Einblick in den ökologischen und sozialen Fußabdruck der Modeindustrie und stellt zum anderen die Gegenseite vor, bei der Wert auf faire Produktion und Nachhaltigkeit gelegt wird. Das Buch „Entschleunigen“ soll über die Missstände in der Textilbranche informieren, jedoch im Umkehrschluss dazu motivieren, diese mit einfachen Mitteln zu verbessern. KW - Modeindustrie KW - Kleidung KW - langsam KW - schnell KW - nachhaltig Y1 - 2022 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER - TY - THES A1 - Bayer, Sebastian T1 - Ligatura : a contemporary blackletter N2 - Die Ligatura ist eine modulare, experimentelle Schrift, die für die Anwendung in großen Formaten gestaltet ist. In ihrer äußeren Erscheinung orientiert sie sich an verschiedenen gebrochenen Schriften. Der Fokus in der Gestaltung der Schrift liegt allerdings auf der Verwendung von Ligaturen, welche sowohl nach historischen als auch nach zeitgenössischen Vorbildern und Gestaltungsprinzipien gebildet werden. Die Ligatura ermöglicht es, eine große Anzahl an Buchstabenkombinationen als Ligatur zu setzen. Dadurch wird innerhalb der Schrift mit Abständen zwischen Buchstaben und somit auch mit unseren Lesegewohnheiten gespielt. Die Ligatura verbindet nicht nur Buchstaben, Wörter und Zeilen, sondern auch klassische Schriftelemente mit der Moderne. KW - Typographie KW - Schriftgestaltung KW - Schriftmuster KW - Ligatur KW - Plakate Y1 - 2022 PB - FH Aachen CY - Aachen ER - TY - BOOK A1 - Kurz, Melanie A1 - Schwer, Thilo T1 - Geschichte des Designs N2 - Dieser Band bietet einen kompakten Überblick über die wichtigsten Stationen des Produktdesigns vom Beginn der Industrialisierung bis heute. Im Zentrum stehen ikonische Alltagsgegenstände vom Thonet-Stuhl bis zum iPhone. Anschaulich und kenntnisreich nehmen Melanie Kurz und Thilo Schwer dabei auch die gesellschaftspolitische Situation, in der die Objekte entstanden sind, in den Blick. Y1 - 2022 SN - 978-3-406-78813-0 PB - Beck CY - München ET - 1. Auflage ER - TY - JOUR A1 - Kurz, Melanie T1 - Was heißt: Verantwortung im Design? Historische Positionen JF - Boxhorn: das Magazin aus dem Fachbereich Gestaltung der FH Aachen Y1 - 2018 IS - 34 SP - 26 EP - 33 CY - Aachen ER - TY - CHAP A1 - Kurz, Melanie T1 - Betrifft Design : von historischen Zukunftsperspektiven zu gegenwärtigen Vergangenheitssehnsüchten T2 - Positionen des Neuen : Zukunft im Design Y1 - 2019 SN - 978-3-89986-301-7 SP - 136 EP - 144 PB - avedition CY - Stuttgart ER - TY - JOUR A1 - Kurz, Melanie T1 - Images of Sweden in Germany: from Sundborn and Bullerby to Ikea JF - nomad: the magazine for new design culture, business affairs and contemporary lifestyle Y1 - 2019 SN - 2513-0714 IS - 8 SP - 136 EP - 147 ER - TY - CHAP A1 - Kurz, Melanie T1 - Zur Multikausalität von Designentscheidungen - eine Beispielsammlung T2 - Designentscheidungen: über Begründungen im Entwurfsprozess Y1 - 2021 SN - 978-3-89986-353-6 SP - 22 EP - 43 PB - avedition CY - Stuttgart ER - TY - JOUR A1 - Uysal, Karya A1 - Creutz, Till A1 - Firat, Ipek Seda A1 - Artmann, Gerhard A1 - Teusch, Nicole A1 - Temiz Artmann, Aysegül T1 - Bio-functionalized ultra-thin, large-area and waterproof silicone membranes for biomechanical cellular loading and compliance experiments JF - Polymers N2 - Biocompatibility, flexibility and durability make polydimethylsiloxane (PDMS) membranes top candidates in biomedical applications. CellDrum technology uses large area, <10 µm thin membranes as mechanical stress sensors of thin cell layers. For this to be successful, the properties (thickness, temperature, dust, wrinkles, etc.) must be precisely controlled. The following parameters of membrane fabrication by means of the Floating-on-Water (FoW) method were investigated: (1) PDMS volume, (2) ambient temperature, (3) membrane deflection and (4) membrane mechanical compliance. Significant differences were found between all PDMS volumes and thicknesses tested (p < 0.01). They also differed from the calculated values. At room temperatures between 22 and 26 °C, significant differences in average thickness values were found, as well as a continuous decrease in thicknesses within a 4 °C temperature elevation. No correlation was found between the membrane thickness groups (between 3–4 µm) in terms of deflection and compliance. We successfully present a fabrication method for thin bio-functionalized membranes in conjunction with a four-step quality management system. The results highlight the importance of tight regulation of production parameters through quality control. The use of membranes described here could also become the basis for material testing on thin, viscous layers such as polymers, dyes and adhesives, which goes far beyond biological applications. Y1 - 2022 SN - 2073-4360 VL - 14 IS - 11 SP - 2213 PB - MDPI CY - Basel ER - TY - CHAP A1 - Alt, Helmut T1 - Speicher speichern, Leiter leiten T2 - Generationenprojekt Energiewende : Elektroenergiepolitik im Spannungsfeld zwischen Vision und Mission / Herbert Niederhausen (Hrsg.) Y1 - 2022 SN - 9783755774389 N1 - gedruckt in der Bereichsbibliothek Eupener Str. unter der Signatur 21 ZPM 4 SP - 125 EP - 136 PB - Books on Demand CY - Norderstedt ER - TY - RPRT A1 - Büdenbender, Martin T1 - Atomausstieg in Deutschland – ein zukunftsfähiger Sonderweg im europäischen Kontext? T2 - Arbeitspapiere des Instituts für Genossenschaftswesen der Westfälischen Wilhelms-Universität Münster, Nr. 90 Y1 - 2009 ER - TY - RPRT A1 - Büdenbender, Martin T1 - Entflechtung von Stromnetzen in Deutschland und Europa im Rahmen des dritten EU-Legislativpakets – Eine Problemdarstellung T2 - Arbeitspapiere des Instituts für Genossenschaftswesen der Westfälischen Wilhelms-Universität Münster, Nr. 91 Y1 - 2010 ER - TY - JOUR A1 - Büdenbender, Martin A1 - Janssen, Matthias A1 - Wobben, Magnus T1 - Versorgungssicherheit auf Elektrizitätsmärkten — Investitionsdilemma durch ineffizientes Marktdesign? JF - Zeitschrift für Energiewirtschaft N2 - Dieser Artikel befasst sich mit dem Investitionsdilemma in der Stromerzeugung, welches in unzureichend ausgestalteten liberalisierten Strommärkten zu einem gesamtwirtschaftlich unerwünscht geringen Niveau an Versorgungssicherheit führt. Die originären Ursachen im deutschen Strommarkt liegen in einer eingeschränkten Schadenersatzpflicht der Lieferanten im Falle eines kapazitätsbedingten Stromausfalls und in der zeitlichen Differenz zwischen letzter Handelsmöglichkeit und Lieferung. Letzteres verhindert ein jederzeitiges individuelles Glattstellen von unerwartet auftretenden Ein- bzw. Ausspeiseänderungen. Des Weiteren führen Faktoren wie die fehlende Partizipation der Endverbraucher am Großhandelsmarkt, die nur undifferenziert mögliche Abschaltung von Endverbrauchern oder time lags durch lange Bau- und Genehmigungszeiten von Erzeugungskapazitäten in Verbindung mit über lange Zeiträume nicht versicherbaren Risiken bezüglich Brennstoff-, CO2-Zertifikate- und Strompreisen zu einer Verschärfung der Problematik. Sinnvolle Lösungsansätze sind zum einen die Erhöhung der Intraday-Handelsliquidität zur Verbesserung der Markträumungsfunktion bis möglichst kurz vor Stromlieferung, was z. B. durch eine Förderung der Direktvermarktung Erneuerbarer Energien erreicht werden kann. Zum anderen trägt ein verstärkter Ausbau von smart metern bei Endverbrauchern zu einer höheren Versorgungssicherheit bei, da dies die Glättung von Lastspitzen und die Artikulation der tatsächlichen Zahlungsbereitschaft von Endverbrauchern am Großhandelsmarkt ermöglicht. Y1 - 2009 SN - 1866-2765 VL - 33 IS - 1 SP - 49 EP - 61 ER - TY - JOUR A1 - Büdenbender, Martin T1 - Der Atomausstieg in Deutschland – ein zukunftsfähiger Sonderweg im europäischen Kontext? JF - atw International Journal for Nuclear Power T2 - Opting out of the Peaceful Use of Nuclear Power in Germany — A Promising Special Approach in the European Context KW - Kernenergie KW - Atomausstieg KW - Europäische Energiepolitik Y1 - 2009 SN - 14315254 VL - 54 IS - 10 SP - 616 EP - 627 PB - Inforum CY - Berlin ER - TY - JOUR A1 - Büdenbender, Martin T1 - Auswirkungen der europäischen Energiepolitik auf den deutschen Atomausstieg JF - Zeitschrift für Energiewirtschaft N2 - Nach der Bundestagswahl am 27. September 2009 steht der Atomausstieg in Deutschland wieder ganz oben auf der politischen Agenda. Eine aktuelle Bestandsaufnahme aller ma\geblichen Argumente erscheint somit zwingend notwendig. Dabei sollte der Blickwinkel nicht national beschränkt bleiben, sondern vor allem der Einfluss der europäischen Dimension dieser Thematik miteinbezogen werden. Auf europäischer Ebene zeigt sich eine Position zu Gunsten der Kernenergie. Unter den 27 EU-Staaten findet gerade eine Renaissance der Atomkraft statt. Die drei europäischen Organe befürworten den umfangreichen Einsatz der Kernenergie als langfristigen Bestandteil des Energieträgermix. Deutschland gehört mit seinem Beschluss zum Atomausstieg einer Minderheit an. Als Teil eines immer stärker zusammen wachsenden und letztendlich vollständig integrierten europäischen Strommarktes wird Deutschland langfristig stets mit Atomstrom versorgt werden. Dies gilt losgelöst von dem Einsatz von Kernkraftwerken im Inland. Eine Abschaltung der Anlagen führt damit nicht zur Zielerreichung der Atomkraftgegner, sondern lediglich zu zusätzlichen energietechnischen Herausforderungen bei der Sicherstellung der deutschen Stromversorgung. Der deutsche Atomausstieg sollte aus diesem Grund von der neuen Bundesregierung zurück genommen werden. Y1 - 2009 SN - 1866-2765 U6 - https://doi.org/10.1007/s12398-009-0039-4 VL - 33 IS - 4 SP - 341 EP - 350 PB - Vieweg CY - Wiesbaden ER - TY - BOOK A1 - Büdenbender, Martin T1 - Auswirkungen des europäischen CO2-Handelssystems auf Stromerzeugungsinvestitionen - mögliche Ausgestaltung des Systems ab 2013 T3 - Düsseldorfer Schriften zum Energie- und Kartellrecht ; Bd. 13 N2 - Zahlreiche Einflussfaktoren haben in den vergangenen Jahren das Gesicht der Elektrizitätsmärkte stark verändert. Hierzu zählen vor allem die Einführung der ökonomischen Gesetze des Wettbewerbsmarktes durch die Liberalisierung sowie die nun kostenpflichtige Berücksichtigung des bei der Stromerzeugung hervorgerufenen CO2-Ausstoßes durch die Einführung des europäischen Emissionshandelssystems (EUTS). Die Folgen dieses Veränderungsprozesses lassen sich auf Grund der langen Investitionszyklen im Kraftwerksbau bisher nur unvollständig überblicken. Dies ist insbesondere im Hinblick auf die Versorgungssicherheit als Teil des energiewirtschaftlichen Zieldreiecks des § 1 EnWG von großer Bedeutung. Dazu zählt insbesondere, ob die Versorgungssicherheit in Deutschland bei gegenwärtigem Marktdesign auch dauerhaft gewährleistet sein wird. Es stellt sich heraus, dass es im Bereich der Spitzenlastkraftwerke zu Investitionen in gesamtwirtschaftlich zu geringen Umfang kommen kann. Dieses Investitionsdilemma beruht auf einem externen Effekt, der durch die aktuelle Ausgestaltung des deutschen Schadenersatzrechtes entsteht. Hierdurch ist die sichere Stromversorgung in Zeiten hoher Last potenziell gefährdet. Um die Wirkungen des Investitionsdilemmas abzumildern oder ganz zu beseitigen sind verschiedene Investitionsanreize durch entsprechende Ausgestaltung des EUTS denkbar. Diese werden im Einzelnen analysiert. KW - Elektrizitätserzeugung KW - Investitionsentscheidung KW - Umweltzertifikathandel KW - Emissionshandelssystem Y1 - 2009 SN - 9783942370318 PB - etv Energieverlag CY - Essen ER - TY - THES A1 - Büdenbender, Martin T1 - Entflechtungskonzepte für Stromübertragungsnetze : ein ökonomischer Vergleich T2 - Münstersche Schriften zur Kooperation ; Bd. 101 N2 - Netzsektoren und deren adäquate Regulierung sind ein sehr relevantes und aktuelles Thema. Dies gilt sowohl für die ökonomische Theorie, die sich sehr intensiv damit auseinandersetzt und in den letzten Jahrzehnten zahlreiche neue Erkenntnisse gewonnen hat. Es gilt ebenso für die Politik, in der Regulierungsfragen kontrovers diskutiert werden und dies nicht nur unter ökonomischen Gesichtspunkten. Es gilt selbstverständlich für die regulierten Unternehmen selbst, deren Tätigkeit durch die staatlichen Regulierungsvorgaben markant beeinflusst wird. Nicht nur die konkreten Inhalte der Regulierungsregime sowie die verbleibenden Freiheitsgrade in der Ausgestaltung sind von Bedeutung, sondern ebenso die Umsetzung durch die Regulierungsbehörden. All dies gilt für den Strommarkt und seinen regulatorischen Hintergrund in besonderer Weise. Die Entflechtung der Stromübertragungsnetze von der Stromproduktion und damit die Vorgaben für die Organisation der Wertschöpfungsketten in den Elektrizitätsunternehmen sind seit dem Beginn des europäischen Liberalisierungsprozesses der Strommärkte ein wichtiges und kontrovers diskutiertes Regulierungselement. Den Fokus bildet das vertikale Unbundling, das letztlich die Diskriminierung von Wettbewerbern durch Anbieter mit aggregierten Wertschöpfungsketten verhindern soll, indem diese gezwungen werden, ihren "Netzteil" anders zu organisieren oder zu verkaufen. Den Mitgliedsstaaten blieben Freiräume in der Ausgestaltung, die in Deutschland erst vor kurzem konkretisiert wurden, und die für die regulierten Unternehmen die Nutzung eines Wahlrechts beinhalten. Der wirtschaftspolitischen folgt nun eine unternehmerische Abwägungsentscheidung. KW - Energiewirtschaft KW - Ownership Unbundling KW - Übertragungsnetz KW - Stromnetz KW - 3. EU Legislativpaket Y1 - 2012 SN - 978-3-8440-1460-0 N1 - Zugl.: Münster (Westfalen), Univ., Diss., 2012 Inhaltsverzeichnis: https://d-nb.info/1027395791/04 PB - Shaker CY - Düren ER - TY - CHAP A1 - Ostkotte, Sebastian A1 - Peters, Constantin A1 - Hüning, Felix A1 - Bragard, Michael T1 - Design, implementation and verification of an rotational incremental position encoder based on the magnetic Wiegand effect T2 - 2022 ELEKTRO (ELEKTRO) N2 - This paper covers the use of the magnetic Wiegand effect to design an innovative incremental encoder. First, a theoretical design is given, followed by an estimation of the achievable accuracy and an optimization in open-loop operation. Finally, a successful experimental verification is presented. For this purpose, a permanent magnet synchronous machine is controlled in a field-oriented manner, using the angle information of the prototype. KW - Position Encoder KW - Rotational Encoder KW - Wiegand Effect KW - Angle Sensor KW - Incremental Encoder Y1 - 2022 SN - 978-1-6654-6726-1 SN - 978-1-6654-6727-8 U6 - https://doi.org/10.1109/ELEKTRO53996.2022.9803477 SN - 2691-0616 N1 - 2022 ELEKTRO (ELEKTRO), 23-26 Mai 2022, Krakow, Poland. PB - IEEE ER - TY - JOUR A1 - Schneider, Jules A1 - Schwabedal, Justus T. C. A1 - Bialonski, Stephan T1 - Schlafspindeln – Funktion, Detektion und Nutzung als Biomarker für die psychiatrische Diagnostik JF - Der Nervenarzt N2 - Hintergrund: Die Schlafspindel ist ein Graphoelement des Elektroenzephalogramms (EEG), das im Leicht- und Tiefschlaf beobachtet werden kann. Veränderungen der Spindelaktivität wurden für verschiedene psychiatrische Erkrankungen beschrieben. Schlafspindeln zeigen aufgrund ihrer relativ konstanten Eigenschaften Potenzial als Biomarker in der psychiatrischen Diagnostik. Methode: Dieser Beitrag liefert einen Überblick über den Stand der Wissenschaft zu Eigenschaften und Funktionen der Schlafspindeln sowie über beschriebene Veränderungen der Spindelaktivität bei psychiatrischen Erkrankungen. Verschiedene methodische Ansätze und Ausblicke zur Spindeldetektion werden hinsichtlich deren Anwendungspotenzial in der psychiatrischen Diagnostik erläutert. Ergebnisse und Schlussfolgerung: Während Veränderungen der Spindelaktivität bei psychiatrischen Erkrankungen beschrieben wurden, ist deren exaktes Potenzial für die psychiatrische Diagnostik noch nicht ausreichend erforscht. Diesbezüglicher Erkenntnisgewinn wird in der Forschung gegenwärtig durch ressourcenintensive und fehleranfällige Methoden zur manuellen oder automatisierten Spindeldetektion ausgebremst. Neuere Detektionsansätze, die auf Deep-Learning-Verfahren basieren, könnten die Schwierigkeiten bisheriger Detektionsmethoden überwinden und damit neue Möglichkeiten für die praktisch KW - Schlafspindeldetektion KW - Psychiatrische Biomarker KW - · Psychiatrische Erkrankungen/Diagnostik KW - Elektroenzephalographie KW - Deep Learning Y1 - 2022 U6 - https://doi.org/10.1007/s00115-022-01340-z SN - 1433-0407 SP - 1 EP - 8 PB - Springer CY - Berlin, Heidelberg ER - TY - CHAP A1 - Büsgen, André A1 - Klöser, Lars A1 - Kohl, Philipp A1 - Schmidts, Oliver A1 - Kraft, Bodo A1 - Zündorf, Albert T1 - Exploratory analysis of chat-based black market profiles with natural language processing T2 - Proceedings of the 11th International Conference on Data Science, Technology and Applications N2 - Messenger apps like WhatsApp or Telegram are an integral part of daily communication. Besides the various positive effects, those services extend the operating range of criminals. Open trading groups with many thousand participants emerged on Telegram. Law enforcement agencies monitor suspicious users in such chat rooms. This research shows that text analysis, based on natural language processing, facilitates this through a meaningful domain overview and detailed investigations. We crawled a corpus from such self-proclaimed black markets and annotated five attribute types products, money, payment methods, user names, and locations. Based on each message a user sends, we extract and group these attributes to build profiles. Then, we build features to cluster the profiles. Pretrained word vectors yield better unsupervised clustering results than current state-of-the-art transformer models. The result is a semantically meaningful high-level overview of the user landscape of black market chatrooms. Additionally, the extracted structured information serves as a foundation for further data exploration, for example, the most active users or preferred payment methods. KW - Clustering KW - Natural Language Processing KW - Information Extraction KW - Profile Extraction KW - Text Mining Y1 - 2022 SN - 978-989-758-583-8 U6 - https://doi.org/10.5220/0011271400003269 SN - 2184-285X N1 - 11th International Conference on Data Science, Technology and Applications DATA - Volume 1, 83-94, 2022, Lisbon, Portugal SP - 83 EP - 94 ER - TY - THES A1 - Lesmeister, David T1 - VIUR : urbanes Lagerfeuer N2 - Es kann ganze Lebensräume auslöschen, und doch wäre unsere Welt nicht die gleiche ohne Feuer. Feuer spielt eine wichtige Rolle in der menschlichen Evolution und diente unseren Vorfahren zum Schutz vor wilden Tieren, Kochen und zum Wärmen. Auch Gespräche am Lagerfeuer sollen einen erheblichen Einfluss auf die soziale und kulturelle Evolution des Menschen gehabt haben. Kein Wunder also, dass die Menschen bis heute mit Feuer ein Gefühl von Gemeinschaft und Geborgenheit verbinden. Genau diese Wirkung greift „VIUR“ auf und macht Feuer alltagstauglich für eine Welt, die von Urbanisierung und Digitalisierung geprägt ist. Entstanden ist ein Hybrid aus einem Tischfeuer und einem Grill. Somit entsteht sowohl das sinnliche Erlebnis einer Feuerstelle als auch die Möglichkeit, kleine Speisen zuzubereiten. Die smarte Konstruktion und ein Sicherheitsbrennstoff, mit dem sich kaum Rauch entwickeln kann, ermöglicht die Nutzung im kleinen Garten, aber eben auch auf einem Stadtbalkon. So kann das Lagerfeuer wieder seinen Zauber entfalten. KW - Lagerfeuer KW - Social Cocooning KW - Stress KW - Achtsamkeit KW - Flamme Y1 - 2022 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER - TY - THES A1 - Nigge-Mans, Leonard T1 - Entwicklung einer Arbeitsplatzleuchte N2 - Für manche mag es banal wirken, doch für Gestalter:innen ist sie unverzichtbar: eine wirklich gute Leuchte für den Arbeitsplatz. Sie hat nämlich einen enormen Einfluss auf die Konzentration und den Komfort. Zudem ermöglicht gutes Licht erst ein sauberes und farbechtes Ergebnis. Dafür wurde in diesem Projekt die perfekte Leuchte entwickelt. Sie leuchtet die Arbeitsfläche ideal aus und unterstützt das Lesen, Schreiben oder die Arbeit mit technischen Geräten. Durch fünf Drehpunkte ist die Leuchte in alle Richtungen zu bewegen und lässt sich somit individuell auf ihre Aufgaben anpassen. Außerdem wurde Wert daraufgelegt, bestehende Normen und Vorschiften einzuhalten, um den Arbeit- und Gesundheitsschutz zu gewährleisten. Feierabend? Durch die Dim-Funktion wird die Arbeitsleuchte zu einer gemütlichen Lichtquelle. Unter anderem durch die unsichtbare Stromführung überzeugt die Lampe mit ihrer minimalistischen Designsprache und lässt sich in unterschiedlichste Räume integrieren. KW - Minimalistisch KW - Elegant KW - Auffällig KW - Multifunktional KW - Steuerbar Y1 - 2022 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER - TY - THES A1 - Kaspor, Alexej T1 - Kritik der digitalen Rationalisierung N2 - Digitalisierung macht’s möglich: mittlerweile beziehen sich Designer:innen in ihrer Konzeptentwicklung immer häufiger auf Referenzdesigns. Sie picken sich die Eigenschaften aus ihnen heraus, von denen sie sich die größte Marktfähigkeit versprechen, und basteln sie zu einem neuen Produkt zusammen. Voilà. Doch wie unkonventionell kann Design noch sein? Wie viel Luft bleibt der Kreativität unter dem immer enger geschnürten Korsett der Marktfähigkeit? Alexej Kaspor eröffnet die Diskussion mit einem provokanten Projekt, das einen kritischen Blick in die Zukunft des Industriedesigns wirft. Dazu fasst er gängige Designprogramme in einer Software zusammen und verbindet sie mit einer künstlichen Intelligenz, die die aktuelle Entwicklung digital rationalisieren und auf die Spitze treiben soll. Diese führt Meta-Analysen über das Nutzungsverhalten durch und prüft damit Frameworks von Referenzdesigns auf ihre Vermarktbarkeit. Aus diesen entwickelt sie dann Gestaltungsvorschläge, ohne beim Seiltanz zwischen Trendhörigkeit und Scheinindividualismus aus dem Gleichgewicht zu kommen. Innerhalb von Sekunden werden den Designer:innen perfekte Vorschläge übers Metaverse simuliert. Auf dem Silbertablett serviert, übersichtlich und gefährlich einfach. Bereit, kombiniert und in Produktion gebracht zu werden. Auch mit dem Tracking der KI kann niemand mithalten: um immer am Puls der Zeit zu bleiben, benachrichtigt sie die Designer:innen in Echtzeit über die neuesten Innovationen und Trends. Ressourcenraubendes Herumprobieren in CAD-Programmen gehört also der Vergangenheit an. Das Programm schafft Abhilfe, und verspricht dabei auch noch die höchste Effizienz, konkret: garantiertes Kapital. Schlagende Argumente, die die Schwächen der Konsumgesellschaft und Kommerzialisierung gezielt ausgenutzen. Es entsteht die perfekte Marketingmaßnahme, ein genialer Treiber für den Turbokapitalismus. Kram, den niemand braucht und zynische Statussymbole inklusive. Der Stolz der geltungsbedürftigen Designer:innen wird dabei selbstverständlich nicht untergraben. Sie sollen mitziehen. Mit zahlreichen Notches wird der Erfolg und die Konkurrenzfähigkeit des Produkts prognostiziert und ihnen Honig ums Maul geschmiert. Die beklemmende Vorahnung wird sich bestätigen. Schritt für Schritt enteignet die KI den Designer:innen ihre Kreativität, bis sie nicht mehr sind als die Kurator:innen berechenbarer Produktkonzepte. Der Spätkapitalismus hat sie in der Mangel. Versprochen: diese Arbeit lässt niemanden kalt. KW - Digitalisierung KW - Designprogramme KW - Nutzungsverhalten KW - Marktfähigkeit KW - künstliche Intelligenz Y1 - 2022 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER - TY - THES A1 - Leontieva, Ksenia Andreevna T1 - Die Facetten Hamburgs N2 - Im Rahmen dieser Masterarbeit entsteht ein neues Erscheinungsbild für die "Stiftung Historische Museen Hamburg". Dabei wurde ein medienübergreifendes Gestaltungskonzept entwickelt, welches dazu dienen soll, die Stiftung und deren musealen Einrichtungen modern, aussagekräftig und repräsentativ neu aufleben zu lassen, als auch das Interesse unserer Gesellschaft für Kunst, Kultur und Geschichte zu wecken und damit die Zielgruppe zu erweitern. Hierzu wurde das Corporate Design neu entwickelt, minimalisiert und modernisiert. Durch den aufgeräumten und organisierten digitalen Auftritt gelangen Interessenten schneller und gezielter zu Informationen über die Stiftung, die einzelnen Museen und deren Programm und Ausstellungen. Zusätzlich dienen als weiterführende Informationsquellen neu getslatete analoge Medien in Form von Plakaten, Flyern, Broschüren und Eintrittskarten. Weitestgehend wurde das Corporate Design in den urbanen Lebensraum der Stadt Hamburg integriert und neu interpretiert. Aus dem Gestaltungskonzept lässt sich ebenfalls ein neues Leitsystem zur besseren Orientierung in den Museen ableiten. Das Designkonzept zieht sich wie ein roter Faden durch alle Medien, um eine Einheit und einen Wiedererkennungswert zu schaffen und seriös und informativ zu wirken. Das Projekt ist rein fiktiv. KW - Informativ KW - Aufklärend KW - Historisch KW - Emotional KW - Wegweisend Y1 - 2022 PB - FH Aachen CY - Aachen ER - TY - THES A1 - Scherer, Maike T1 - Social Integrity for distributed Workforces : ein Design System für soziale Interaktion eines Unternehmens N2 - Eine Applikation für die soziale Interaktion zwischen Teams und Arbeitnehmern eines Unternehmens, welche Remote und/oder Hybrid arbeiten. Wissen teilen, Weiterbilden, Wohlfühlen In den letzten zwei Jahren kam es auf Grund der Corona-Pandemie, trotz der vielen Kommunikationsmöglichkeiten, im Privat-, sowie Arbeitsleben zu erheblichen sozialen Einschränkungen. Genau hier setzt die Applikation „Companion“ an, um dem Arbeitnehmer das In-Office-Gefühl auch Remote übersetzen zu können. Der Arbeitnehmer kann mit seinen Kollegen sozialisieren, diese besser kennenlernen und wird zusätzlich durch Events und Workshops professionell weitergebildet. KW - Remote Work KW - Hybrid Work KW - soziale Integration KW - Integration KW - Interaktion Y1 - 2022 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER - TY - THES A1 - Lawrenz, Anne Murielle T1 - Lebens.Mittel.Punkt : Konzeption und Gestaltung einer Anwendung für Ernährungsberatung N2 - „kocotte“ (eine Abwandlung eines kleinen Kochtopfs) soll drei aktuelle ­Ernährungstrends kombinieren: Gesundheit, Nachhaltigkeit und Genuss. Der Markt bietet viele Angebote, die einen oder auch zwei Themen kombinieren – von Special-Interest-Publikationen über Diätprogramme bis hin zu Foodvereinigungen – alle mit Daseinsberechtigung. Will oder muss ich aber beispielsweise meine Essgewohnheiten umstellen, gibt es kein überzeugendes Werkzeug, das mir alle drei Themen zusammenfasst. Hier soll „kocotte“ ein neues Angebot machen. KW - Ernährung KW - Genuss KW - Nachhaltigkeit KW - Geschmack KW - Gesundheit Y1 - 2022 PB - FH Aachen CY - Aachen ER - TY - THES A1 - Krebs, Benedikt T1 - Das Online-Ich : Erlebnis-Installation zur Reflexion über das digitale Selbst N2 - Soziale Netzwerke gehören zu den größten Konzernen der Welt. Hier werden minütlich Millionen von Nachrichten verschickt. Das Internet spielt eine stetig wachsende Rolle in der zwischenmenschlichen Kommunikation. Und doch funktioniert dort nicht nur die Sprache anders, auch die Persönlichkeit der Menschen kann sich auch verändern. Diese Arbeit beschäftigt sich mit dem „Online-Ich“, das jeder in sich tragen soll. Häufig ist dieses offener, hilfsbereiter und selbstloser, aber eben auch reizbarer, aggressiver und energetischer. Um auf diese Veränderung aufmerksam zu machen, werden die analoge und digitale Persönlichkeit verglichen. Dazu schöpft die Arbeit aus den vielfältigen Möglichkeiten von Virtual Reality, um Betrachtende in die Arbeit miteinzubeziehen. KW - Virtuelle Realität KW - Online KW - Enthemmung KW - Messestand KW - 3D Y1 - 2022 PB - FH Aachen CY - Aachen ER - TY - THES A1 - Zimmer, Miriam T1 - Uniform : Identitätsbildende Prozesse uniformer Bekleidungspraxen N2 - Kleidung umgibt den menschlichen Körper seit etwa 75.000 Jahren. Seitdem dient sie dabei längst mehr nur als Schutz, sondern ist zu einem wichtigen Kommunikationsmittel geworden. Vor allem Identität spielte schon immer eine wichtige Rolle in ihrer Funktion. Im 15. Jahrhundert entstand die erste Uniform, die durch identische Kleidung Zusammengehörigkeit vermitteln sollte. Dieses Konzept findet heute in der Corporate Fashion, Berufskleidung und zivilen Kontexten Verwendung und vermittelt nebenher Visionen und Philosophien der Corporate Identities. In dieser Arbeit wurde eine tiefgehende Recherche über die Geschichte, Funktion und Wirkung von Uniformen betrieben und Kategorien untersucht, in die sich diese einteilen lassen. Anschließend wurden die Ergebnisse in einem ausgewählten Layout als Buch zusammengefasst und mit Portraits uniformtragender Menschen unterstützt. Abschließend folgt ein Leitfaden, der eine gezielte Gestaltung von Uniformen ermöglicht. KW - Uniform KW - Buchgestaltung KW - Unternehmensbekleidung KW - Erscheinungsbild KW - Designtheorie Y1 - 2022 PB - FH Aachen CY - Aachen ER - TY - THES A1 - Nicolay, Victoria T1 - Shaping the future of gender equality N2 - Die Thematik um die Gleichberechtigung von Mann und Frau ist eine hoch aktuelle und wird die Gesellschaft auch in Zukunft weiterhin beschäftigen. Probleme bestehen dabei überall auf der Welt, unterscheiden sich jedoch grundlegend. Obwohl die Voraussetzungen global andere sind, ist das Ziel das gleiche. Die Gleichberechtigung von Mann und Frau. Mit Equality Help entsteht eine Möglichkeit, individuelle Lösungen und Hilfestellungen für jede:n einzelne:n Nutzer:in zu finden. Entscheidend ist dabei die Zusammenarbeit von Wirtschaft, Gesellschaft und Hilfsorganisationen. Mit Hilfe der Digitalisierung kann ein globaler Austausch stattfinden, sowie effizient Prozesse erleichtert werden und für die Thematik sensibilisiert werden. Ziel ist es, Betroffenen zu helfen, als auch jeden Einzelnen in Verantwortung zu nehmen um den gesellschaftlichen Wandel positiv zu beeinflussen.  KW - Gleichberechtigung KW - Hilfsangebote KW - Austausch KW - Digitalisierung KW - Gesellschaft Y1 - 2022 PB - FH Aachen CY - Aachen ER - TY - THES A1 - Deckers Catorze, Yoko Joana T1 - Self Made Man N2 - Selbst in unserer heutigen, modernen Gesellschaft gehört das Thema ‚Transgender‘ noch für einige Menschen zu den Tabuthemen. Transgender sind Menschen, bei denen die gefühlte, geschlechtliche Identität nicht mit dem bei der Geburt zugewiesenem, körperlichem Geschlecht übereinstimmt. Dabei definiert sich die Geschlechterrolle nicht nur durch die Sexualität, sondern durch die ganze Persönlichkeit eines Menschen. Trans* Personen wollen in erster Linie von der Gesellschaft als Menschen akzeptiert werden. Eine erfolgte oder angestrebte Geschlechtsumwandlung ist damit nicht zwingend verbunden. Das Projekt soll zeigen, dass Trans*Personen Menschen sind wie jeder andere auch. Es geht nicht um die Sexualität sondern um den Menschen und seine Geschichte. Mithilfe des Bildbandes soll man die Person “Jay Moch“ ohne Vorurteile gegenüber dem Thema “Transgeschlechtlichkeit“ kennenlernen. Am Anfang lernt man einen jungen Mann kennen, der gerne ins Fitnessstudio geht und Shisha raucht. Je tiefer man das Buch durchblättert und hinschaut, desto mehr erfährt man über seine inspirierende Lebensgeschichte und die Umwandlung zum Mann. KW - Transgender KW - Diversität KW - intim KW - LGBTQI KW - Fotodokumentation Y1 - 2022 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER - TY - THES A1 - Gaspard, Luca T1 - Bratnice N2 - Als Sohn meines Vaters und Enkelsohn meiner Großeltern war Slowenien immer Bestandteil meiner Sozialisation, ein unsichtbarer Teil, dem ich durch meine Fotografien auf der Reise nach „Bratnice“ eine Gestalt gegeben habe. Dabei handelt es sich um ein Dorf, indem meine Familie vor ungefähr 35 Jahren eine Holzhütte unmittelbar in der Nähe der Geburtsstätte meines Großvaters errichtet hat. Ich begann den alten Geschichten Eigene hinzuzufügen, die alten Bilder um neue zu erweitern und Slowenien und die Menschen neu kennenzulernen. Dies heißt auch, mich zum Teil von den Vorstellungen meines Vaters und denen meiner Großeltern loszulösen. Meine eigene Auseinandersetzung mit der slowenischen – ehemals sozialistischen – Realität und dem kapitalistisch westlichen System ist eng verknüpft mit einer Untersuchung des Begriffs „Status“. Wie sind meine slowenischen und deutschen Wurzeln für mich vereinbar? Woher kommt das Streben nach den einschlägigen Statussymbolen und sind materielle Vorstellungen immer noch prägend? KW - persönlich KW - "Bratnice" KW - Heimat KW - materieller Status KW - fotografisches Forschen Y1 - 2022 PB - FH Aachen CY - Aachen ER -