TY  - CHAP
A1  - Reisgen, Uwe
A1  - Schleser, Markus
A1  - Abdurakhmanov, Aydemir
A1  - Turichin, Gleb
A1  - Valdaitseva, Elena
A1  - Bach, Friedrich-Wilhelm
A1  - Hassel, Thomas
A1  - Beniyashi, Alexander
T1  - Investigation of factors for defect-free weld formation by non-vacuum electron beam welding
T2  - Laser technologies in welding and materials processing : proceedings of the fifth international conference, 24 - 27 May 2011, Katsiveli, Crimea, Ukraine
Y1  - 2011
SP  - 104
EP  - 109
PB  - Paton Publ. House
CY  - Kiev
ER  - 
TY  - JOUR
A1  - Reisgen, Uwe
A1  - Schleser, Markus
A1  - Abdurakhmanov, Aydemir
A1  - Gumenyuk, Andrey
T1  - Measuring of plasma properties induced by non-vacuum electron beam welding
JF  - Physics of plasma
N2  - Electron beam plasma measurement was realised by means of DIABEAM system invented by ISF RWTH Aachen. The Langmuir probe method is used for measurement. The relative simplicity of the method and the possibility of dispersion of high power on the probe allow its application for the investigation of high-power electron beams. The key element of the method is a rotating thin tungsten wire, which intersects the beam transversely on its axis and collects part of the current by itself. The signals, which are registered in the DIABEAM as a voltage, were taken in the form of amplitude. The conversion of the probe current into the distribution along the beam radius was realised using the Abel’s method. A voltage-current characteristic was built for the beam current. The local electron density as well as the electron temperature, the floating potential and the plasma potential were measured and calculated by means of this characteristic.
Y1  - 2012
U6  - http://dx.doi.org/10.1063/1.3675874
SN  - 1089-7674 (E-Journal); 1070-664X (Print)
VL  - 19
IS  - 1
SP  - 1
EP  - 7
PB  - AIP Publishing
CY  - Melville, NY
ER  - 
TY  - CHAP
A1  - Reisgen, Uwe
A1  - Schleser, Markus
A1  - Abdurakhmanov, Aydemir
A1  - Gumenyuk, Andrej
T1  - Application of electron beam welding to fabrication of steel-aluminium dissimilar joint
T2  - Beam technologies & laser application : proceedings of the VII international conference, Saint Petersburg, Sept. 18-21, 2012
Y1  - 2012
SP  - 265
EP  - 279
PB  - Publ. House
CY  - Saint Petersburg
ER  - 
TY  - CHAP
A1  - Reisgen, Uwe
A1  - Schleser, Markus
A1  - Abdurakhmanov, Aydemir
A1  - Gumenyuk, Amdrej V.
ED  - Turichin, G.
T1  - Measurement method of electron beam plasma parameters by non-vacuum electron beam welding
T2  - Beam technologies & laser application : proceedings of the VI international conference, Saint Petersburg, Sept. 23-25, 2009
Y1  - 2009
SP  - 259
EP  - 267
PB  - Politechnical Univ.
CY  - Saint Petersburg
ER  - 
TY  - JOUR
A1  - Reisgen, Uwe
A1  - Olschok, Simon
A1  - Jakobs, Stefan
A1  - Schleser, Markus
A1  - Mokrov, Oleg
A1  - Rossiter, Eduardo
T1  - Laser beam submerged arc hybrid welding
JF  - Physics procedia
N2  - The laser beam-submerged arc hybrid welding method originates from the knowledge that, with increasing penetration depth, the laser beam process has a tendency to pore formation in the lower weld regions. The coupling with the energy-efficient submerged-arc process improves degassing and reduces the tendency to pore formation. The high deposition rate of the SA process in combination with the laser beam process offers, providing the appropriate choice of weld preparation, the possibility of welding plates with a thickness larger than 20° mm in a single pass, and also of welding thicker plates with the double-sided single pass technique.
Y1  - 2012
U6  - http://dx.doi.org/10.1016/j.phpro.2012.10.016
SN  - 1875-3892
N1  - Part of special issue "Laser assisted net shape engineering 7 (LANE 2012)"
VL  - 39
SP  - 75
EP  - 83
PB  - Elsevier
CY  - Amsterdam
ER  - 
TY  - CHAP
A1  - Raupach, Michael
A1  - Orlowsky, Jeannette
A1  - Büttner, T.
A1  - Dilthey, Ulrich
A1  - Schleser, Markus
ED  - Hegger, Josef
T1  - Epoxy-impregnated textiles in concrete - load bearing capacity and durability
T2  - Textile reinforced concrete : proceedings of the 1. International RILEM Conference, held at the RWTH Aachen, September 6/7, 2006. (RILEM proceedings ; 50)
Y1  - 2006
SN  - 2-912143-97-7
SP  - 77
EP  - 88
PB  - RILEM Publ.
CY  - Bagneux
ER  - 
TY  - JOUR
A1  - Ramazani, Ali
A1  - Li, Yang
A1  - Mukherjee, Krishnendu
A1  - Prahl, Ulrich
A1  - Bleck, Wolfgang
A1  - Abdurakhmanov, Aydemir
A1  - Schleser, Markus
A1  - Reisgen, Uwe
T1  - Microstructure evolution simulation in hot rolled DP600 steel during gas metal arc welding
JF  - Computational materials science
Y1  - 2013
SN  - 1879-0801 (E-Book); 0927-0256 (Print)
VL  - Vol. 68
SP  - 107
EP  - 116
PB  - Elsevier
CY  - Amsterdam
ER  - 
TY  - CHAP
A1  - Quadflieg, Till
A1  - Schoene, Jens
A1  - Schleser, Markus
A1  - Jockenhövel, Stefan
A1  - Reisgen, Uwe
A1  - Gries, Thomas
ED  - Heslehurst, Rikard Benton
T1  - Shear connectors for hybrid joints of metal and FRP
T2  - Diversity in composites : conference proceedings : Composites Australia and CRC-ACS 2012 conference
Y1  - 2012
SN  - 978-0-9873285-0-2
SP  - [152]
EP  - [160]
PB  - Composites Australia
CY  - Hawthorne
ER  - 
TY  - CHAP
A1  - Pak, Daniel
A1  - Piegeler, D.
A1  - Feldmann, Markus
A1  - Schleser, Markus
A1  - Dilthey, Ulrich
ED  - Hegger, Josef
T1  - Hybrid joints of textile reinforced concrete parts - designed for assembly
T2  - Textile reinforced concrete : proceedings of the 1. International RILEM Conference, held at the RWTH Aachen, September 6/7, 2006. (RILEM proceedings ; 50)
Y1  - 2006
SN  - 2-912143-97-7
SP  - 181
EP  - 190
PB  - RILEM Publ.
CY  - Bagneux
ER  - 
TY  - JOUR
A1  - Mukherjee, Krishnendu
A1  - Ramazani, Ali
A1  - Yang, Li
A1  - Prahl, Ulrich
A1  - Bleck, Wolfgang
A1  - Reisgen, Uwe
A1  - Schleser, Markus
A1  - Abdurakhmanov, Aydemir
T1  - Characterization of gas metal arc welded hot rolled DP600 steel
JF  - Steel research international
Y1  - 2011
SN  - 1869-344X (E-Book); 1611-3683 (Print)
VL  - Vol. 82
IS  - Iss. 12
SP  - 1408
EP  - 1416
PB  - Wiley
CY  - Weinheim
ER  -