TY - GEN A1 - Samm, Doris A1 - Perteck, Patrik T1 - Der Helium-Neon-Laser N2 - In der Lerneinheit werden zunächst anschaulich die Eigenschaften verschiedener Lichtquellen sowie wichtige Begriffe erläutert. Anschließen wird das physikalische Prinzip des HeNe-Lasers erklärt. Die Lerneinheit endet mit der Beschreibung des technischen Aufbaus eines HeNe-Lasers. KW - Helium-Neon-Laser KW - Lichtquelle KW - Lichtabsorption KW - Lichtemission KW - Resonator KW - Simulation KW - Virtuelle Realität KW - Lichtbetrachtung KW - Besetzungsinversion KW - He-Ne Laser KW - He-Ne Schema Y1 - 2003 ER - TY - GEN A1 - Samm, Doris A1 - Meurer, Marcel T1 - Die elektrische Leitung und Supraleitung N2 - Die Lerneinheit stellt in anschaulicher Weise die verschiedenen Modelle der elektrischen Leitung dar und führt über diese zur Erklärung der Supraleitung. Effekte und Anwendungen der Supraleitung werden in Animationen und Bildern vorgeführt. Ein umfangreiches Glossar erläutert wichtige Begriffe. KW - Elektrische Leitung KW - Supraleitung KW - Elektronengas KW - Bändermodell KW - Festkörper KW - Elektrische Leitung KW - Supraleitung Y1 - 2003 ER - TY - JOUR A1 - Baroud, G. A1 - Wu, J.Z. A1 - Bohner, M A1 - Sponagel, Stefan A1 - Steffen, T. T1 - How to determine the permeability for cement infiltration into osteoporotic cancellous bone JF - Medical Engineering & Physics. 25 (2003), H. 4 N2 - Cement augmentation is an emerging surgical procedure in which bone cement is used to infiltrate and reinforce osteoporotic vertebrae. Although this infiltration procedure has been widely applied, it is performed empirically and little is known about the flow characteristics of cement during the injection process. We present a theoretical and experimental approach to investigate the intertrabecular bone permeability during the infiltration procedure. The cement permeability was considered to be dependent on time, bone porosity, and cement viscosity in our analysis. In order to determine the time-dependent permeability, ten cancellous bone cores were harvested from osteoporotic vertebrae, infiltrated with acrylic cement at a constant flow rate, and the pressure drop across the cores during the infiltration was measured. The viscosity dependence of the permeability was determined based on published experimental data. The theoretical model for the permeability as a function of bone porosity and time was then fit to the testing data. Our findings suggest that the intertrabecular bone permeability depends strongly on time. For instance, the initial permeability (60.89 mm4/N.s) reduced to approximately 63% of its original value within 18 seconds. This study is the first to analyze cement flow through osteoporotic bone. The theoretical and experimental models provided in this paper are generic. Thus, they can be used to systematically study and optimize the infiltration process for clinical practice. KW - Osteoporose KW - Permeabilität KW - Viskose Strömung KW - Viskosität KW - Vertebroplastie KW - Cement infiltration KW - Vertebroplasty KW - Osteoporosis KW - Permeability KW - Experiment KW - Analysis KW - Viscous flow Y1 - 2003 SN - 1350-4533 SP - 283 EP - 288 ER - TY - JOUR A1 - Kämper, Klaus-Peter A1 - Picard, Antoni A1 - Brill, Manfred A1 - Cassel, Detlev A1 - Jentsch, Andreas A1 - Merten, Sabine A1 - Rollwa, Markus T1 - The Virtual Clean Room - a new tool in teaching MST process technologies N2 - The Virtual Clean Room - a new tool in teaching MST process technologies University education in high-technology fields like MST is not complete without intensive laboratory sessions. Students cannot fully grasp the complexity and the special problems related to the manufacturing of microsystems without a thorough hands-on experience in a MST clean room. KW - Virtuelle Maschine KW - VM KW - Mikrosystemtechnik KW - MST KW - virtual clean room Y1 - 2003 ER - TY - CHAP A1 - Merten, Sabine A1 - Kämper, Klaus-Peter A1 - Brill, Manfred A1 - Picard, Antoni A1 - Cassel, Detlev A1 - Jentsch, Andreas A1 - Rollwa, Markus T1 - Vom virtuellen Wafer zum realen Drucksensor N2 - Das Technologiepraktikum „Virtuelle Sensor-Fertigung“ ist ein Beispiel für die medientechnische Aufbereitung von Lern- und Lehrmaterial unter didaktischen Gesichtspunkten. Studierende lernen einen Fertigungsprozess mit Hilfe von virtuellen Maschinen kennen, bevor sie die reale Prozesskette im Laborpraktikum im Reinraum durchführen. N2 - The technology course “Fabrication of a microsensor” represents a multimediabased approach towards education in high technology production in consideration of didactical aspects. The students learn the operation of a complex microfabrication line with the help of virtual fabrication machines before they perform the actual process in a hands-on training in an actual clean room. KW - Virtuelle Maschine KW - VM KW - Virtuelle Sensor-Fertigung KW - virtual fabrication of a microsensor Y1 - 2003 ER - TY - CHAP A1 - Merten, Sabine A1 - Kämper, Klaus-Peter A1 - Brill, Manfred A1 - Picard, Antoni A1 - Cassel, Detlev A1 - Jentsch, Andreas A1 - Rollwa, Markus T1 - Virtuelle Sensor-Fertigung: Hightech mit LabVIEW N2 - Eine neue Generation von Praktika an Hochschulen wächst heran. Moderne Wege beim Verstehen und Erlernen naturwissenschaftlicher Zusammenhänge sowie industrieller Fertigungsprozesse sind gefordert. Das Technologiepraktikum „Virtuelle Sensor- Fertigung“, entwickelt im Verbundprojekt INGMEDIA an den Fachhochschulen Aachen und Zweibrücken, trägt als neuartiges Lern- und Lehrmodul dieser Forderung Rechnung. Die Studierenden lernen einen vollständigen Fertigungsprozess mit Hilfe von virtuellen, in LabVIEW programmierten Maschinen kennen, bevor sie die reale Prozesskette im Reinraum durchführen. N2 - A new generation of university laboratory courses is presently being developed. Modern concepts for the understanding and learning of applied science and industrial fabrication processes are required. The technology course “Fabrication of a microsensor”, developed by the Universities of Applied Sciences Aachen and Zweibrücken in the joint research project INGMEDIA, represents a new approach towards education in high technology production. The students learn the operation of the complex microfabrication line with the help of virtual fabrication machines, programmed in LabVIEW, before they perform the actual process in a genuine clean room. KW - LabVIEW KW - Virtuelle Sensor-Fertigung KW - Fertigungsprozess KW - virtuelle Maschinen KW - virtual sensor fabrication KW - manufacturing process KW - virtual KW - virtual machines Y1 - 2003 ER - TY - JOUR A1 - Fabo, Sabine T1 - Das Museum lebt? Der Diskurs der Vernetzung im virtuellen Kunstraum JF - Zeitenblicke N2 - Kunstwerke sowie ihre Präsentation und Vermittlung werden zunehmend von digitalen Technologien unterstützt. Virtuelle Ausstellungen, Internet-Projekte und komplexe Datenarchive stellen das Kunstwerk in einen medialen Kontext, der weit über das Moment einer technischen Reproduzierbarkeit hinausgeht. Das allgegenwärtige Konzept der Vernetzung dynamisiert Kunst, ihre Rezipienten und Ausstellungsorte. Die Beziehungen zwischen diesen Feldern werden mit Hilfe physiologischer Metaphern definiert und visualisiert. Frühere Speicher und Archive geraten in einen prozessualen Sog, in dem alles fluktuiert, sich kurzweilig verknüpft, auflöst und in permanente Dialoge mit seiner Umgebung tritt - das virtuelle Museum gerät in aktuellen Standortbestimmungen in die definitorische Nähe des Künstlichen Lebens. KW - Elektronische Kunst KW - Netzkunst KW - Museum KW - Museumsorganisation KW - Virtuelles Museum KW - Virtuelle Ausstellung KW - Digitales Museum KW - Vernetzung KW - Elektronische Kunst KW - Virtual Art KW - Virtual Museum KW - Virtual Exhibition KW - Digital Museum KW - Electronic Art Y1 - 2003 VL - 2(2003) IS - 1 ER - TY - CHAP A1 - Staat, Manfred T1 - Design by Analysis of Pressure Components by non-linear Optimization N2 - This paper presents the direct route to Design by Analysis (DBA) of the new European pressure vessel standard in the language of limit and shakedown analysis (LISA). This approach leads to an optimization problem. Its solution with Finite Element Analysis is demonstrated for some examples from the DBA-Manual. One observation from the examples is, that the optimisation approach gives reliable and close lower bound solutions leading to simple and optimised design decision. KW - Analytischer Zulaessigkeitsnachweis KW - FEM KW - Einspiel-Analyse KW - design-by-analysis KW - finite element analysis KW - limit and shakedown analysis Y1 - 2003 ER - TY - JOUR A1 - Staat, Manfred T1 - Shakedown and ratchetting under tension-torsion loadings: analysis and experiments N2 - Structural design analyses are conducted with the aim of verifying the exclusion of ratchetting. To this end it is important to make a clear distinction between the shakedown range and the ratchetting range. The performed experiment comprised a hollow tension specimen which was subjected to alternating axial forces, superimposed with constant moments. First, a series of uniaxial tests has been carried out in order to calibrate a bounded kinematic hardening rule. The load parameters have been selected on the basis of previous shakedown analyses with the PERMAS code using a kinematic hardening material model. It is shown that this shakedown analysis gives reasonable agreement between the experimental and the numerical results. A linear and a nonlinear kinematic hardening model of two-surface plasticity are compared in material shakedown analysis. KW - Einspielen KW - Einspielen KW - Ratchetting KW - Zug-Druck Belastung KW - shakedown KW - ratchetting KW - tension–torsion loading Y1 - 2003 ER - TY - CHAP A1 - Dielmann, Klaus-Peter A1 - Velden, Alwin van der T1 - Virtuelle Kraftwerke - Stand der Technik N2 - Ausgangslage, Funktionsprinzip des virtuellen Kraftwerkes, Energiemanagementsysteme (EMS), Einsatzgebiete, Anlagesysteme eines VKW's, Einsatzbereich der verschiedenen dezentralen Energieanlagen, Vorteile des virtuellen Kraftwerkes, Auswirkungen auf das elektrische Netz, Wirtschaftliche Aspekte, Beispielprojekte KW - Virtuelle Kraftwerke Y1 - 2003 ER -