TY - CHAP A1 - Helsper, Christoph A1 - Dressler, Jörg ED - Gail, Lothar ED - Gommel, Udo ED - Hortig, Hans-Peter T1 - Partikelmesstechnik T2 - Reinraumtechnik N2 - Der Schutz von Produkten vor der Kontamination durch Partikel gilt als eine zentrale Aufgabe der Reinraumtechnik. Da es dabei um Kontaminationseffekte weit unterhalb der visuellen Wahrnehmbarkeit geht, braucht es leistungsfähige Verfahren, um die Messgröße „Partikelkontamination“ über den gesamten Bereich, den Anwender fordern, präzise zu bestimmen. Neben der Partikelhäufigkeit ist dabei die Größe der Partikel, die sowohl das Transportverhalten wie auch die mögliche Wirkung auf das Produkt beeinflusst, von entscheidender Bedeutung. Ferner kann es für die Ermittlung von Kontaminationsquellen von Interesse sein, die Form und die chemische Natur der Partikel zu bestimmen (z. B. textile Fasern, Metallabrieb, flüssige Tröpfchen). Die Partikelhäufigkeit wird üblicherweise als Konzentration, d. h. bezogen auf das analysierte Gasvolumen angegeben. Bei den in reinen Technologien üblichen niedrigen Konzentrationen dient als Häufigkeitsmaß die Partikelanzahlkonzentration, also die Partikelanzahl pro Volumeneinheit des Trägermediums. Y1 - 2012 SN - 978-3-642-19435-1 U6 - http://dx.doi.org/10.1007/978-3-642-19435-1_3 VL - 2012 SP - 69 EP - 95 PB - Springer CY - Berlin ET - 3 ER - TY - CHAP A1 - Digel, Ilya A1 - Mansurov, Zulkhair A1 - Biisenbaev, Makhmut A1 - Savitskaya, Irina A1 - Kistaubaeva, Aida A1 - Akimbekov, Nuraly A1 - Zhubanova, Azhar ED - Hu, Ning T1 - Heterogeneous Composites on the Basis of Microbial Cells and Nanostructured Carbonized Sorbents T2 - Composites and Their Applications N2 - The fact that microorganisms prefer to grow on liquid/solid phase surfaces rather than in the surrounding aqueous phase was noticed long time ago [1]. Virtually any surface – animal, mineral, or vegetable – is a subject for microbial colonization and subsequent biofilm formation. It would be adequate to name just a few notorious examples on microbial colonization of contact lenses, ship hulls, petroleum pipelines, rocks in streams and all kinds of biomedical implants. The propensity of microorganisms to become surface-bound is so profound and ubiquitous that it vindicates the advantages for attached forms over their free-ranging counterparts [2]. Indeed, from ecological and evolutionary standpoints, for many microorganisms the surface-bound state means dwelling in nutritionally favorable, non-hostile environments [3]. Therefore, in most of natural and artificial ecosystems surface-associated microorganisms vastly outnumber organisms in suspension and often organize into complex communities with features that differ dramatically from those of free cells [4]. Y1 - 2012 SN - 978-953-51-0706-4 U6 - http://dx.doi.org/10.5772/47796 SP - 249 EP - 272 PB - Intech CY - London ER - TY - CHAP A1 - Fabo, Sabine ED - Hartmann, Doreen T1 - Gefährliche Liebschaften : Kunst zwischen Widerstand und Umarmung T2 - Interventionen : Grenzüberschreitungen in Ästhetik, Politik und Ökonomie KW - Politische Kunst KW - Künstlerisches Handeln Y1 - 2012 SN - 978-3-7705-5283-2 SP - 173 EP - 189 PB - Fink CY - München ER - TY - CHAP A1 - Fabo, Sabine T1 - Einführung T2 - Vielen Dank für Ihren Einkauf : Konsumkultur aus Sicht von Design, Kunst und Medien Y1 - 2012 SN - 978-3-8376-2170-9 SP - 9 EP - 13 PB - Transcript Verlag CY - Bielefeld ER - TY - CHAP A1 - Fabo, Sabine T1 - Die Kunst der Irritation und ihr Mehrwert T2 - Vielen Dank für Ihren Einkauf : Konsumkultur aus Sicht von Design, Kunst und Medien Y1 - 2012 SN - 978-3-8376-2170-9 SP - 112 EP - 145 PB - Transcript Verlag CY - Bielefeld ER - TY - CHAP A1 - Kurz, Melanie T1 - Prizing & Pricing : Design zwischen Rang und Regal T2 - Vielen Dank für Ihren Einkauf : Konsumkultur aus Sicht von Design, Kunst und Medien Y1 - 2012 SN - 978-3-8376-2170-9 U6 - http://dx.doi.org/10.1515/transcript.9783839421703.26 SP - 26 EP - 39 PB - Transcript Verlag CY - Bielefeld ER - TY - CHAP A1 - Jakobs, Helmut T1 - Vorwort T2 - Vielen Dank für Ihren Einkauf : Konsumkultur aus Sicht von Design, Kunst und Medien Y1 - 2012 SN - 978-3-8376-2170-9 SP - 7 PB - Transcript Verlag CY - Bielefeld ER - TY - CHAP A1 - Hoffschmidt, Bernhard A1 - Alexopoulos, Spiros A1 - Göttsche, Joachim A1 - Sauerborn, Markus T1 - High concentration solar collectors T2 - Comprehensive renewable energy / ed. Ali Sayigh. Vol. 3: Solar thermal systems: components and applications N2 - Solar thermal concentrated power is an emerging technology that provides clean electricity for the growing energy market. To the solar thermal concentrated power plant systems belong the parabolic trough, the Fresnel collector, the solar dish, and the central receiver system. For high-concentration solar collector systems, optical and thermal analysis is essential. There exist a number of measurement techniques and systems for the optical and thermal characterization of the efficiency of solar thermal concentrated systems. For each system, structure, components, and specific characteristics types are described. The chapter presents additionally an outline for the calculation of system performance and operation and maintenance topics. One main focus is set to the models of components and their construction details as well as different types on the market. In the later part of this chapter, different criteria for the choice of technology are analyzed in detail. KW - Central receiver system KW - Concentrated solar collector KW - Fresnel collector KW - Optical and thermal analysis KW - Solar concentration Y1 - 2012 SN - 978-0-08-087873-7 U6 - http://dx.doi.org/10.1016/B978-0-08-087872-0.00306-1 VL - 3 SP - 165 EP - 209 PB - Elsevier CY - Amsterdam ER - TY - CHAP A1 - Hoffschmidt, Bernhard A1 - Alexopoulos, Spiros A1 - Rau, Christoph A1 - Sattler, Johannes, Christoph A1 - Anthrakidis, Anette A1 - Teixeira Boura, Cristiano José A1 - O'Connor, P. A1 - Hilger, Patrick T1 - Concentrating solar power T2 - Comprehensive renewable energy / ed. Ali Sayigh. Vol. 3: Solar thermal systems: components and applications Y1 - 2012 SN - 978-0-08-087872-0 U6 - http://dx.doi.org/10.1016/B978-0-08-087872-0.00319-X VL - 3 SP - 595 EP - 636 PB - Elsevier CY - Amsterdam ER - TY - CHAP A1 - Fabo, Sabine ED - Hartmann, Doreen ED - [u.a.], T1 - Gefährliche Liebschaften : Kunst zwischen Wderstand und Umarmung T2 - Interventionen : Grenzüberschreitungen in Ästhetik, Politik und Ökonomie Y1 - 2012 SN - 978-3-7705-5283-2 SP - 173 EP - 189 PB - Fink CY - München [u.a.] ER - TY - CHAP A1 - Goldbach, Daniel T1 - Zuverlässigkeitsanalyse zur Verifikation der Einhaltung von quantitativen Sicherheitsanforderungen. T2 - Diagnose in mechatronischen Fahrzeugsystemen V : neue Verfahren für Test, Prüfung und Diagnose von E/E-Systemen im Kfz ; [anlässlich der 6. Tagung "Diagnose in Mechatronischen Fahrzeugsystemen" in Dresden]. Bernard Bäker ... (Hrsg.) Y1 - 2012 SN - 978-3-8169-3149-2 SP - 116 EP - 132 PB - Expert Verlag CY - Renningen ER - TY - CHAP A1 - Bagayoko, Lamine A1 - Geissler, Karsten A1 - Koch, Eckart T1 - Dynamik bei Eisenbahnbrücken T2 - Stahlbau-Kalender : [Eurocode-3-Grundnorm; Brücken] ; Jg. 14 / hrsg. von Ulrike Kuhlmann Y1 - 2012 SN - 978-3-433-02988-6 SP - 575 EP - 632 PB - Ernst & Sohn CY - Berlin ER - TY - CHAP A1 - Wollert, Jörg A1 - Rau, Sebastian T1 - Energietransparenz und optimierter Energieverbrauch durch ganzheitliche Automatisierungskonzepte T2 - Smart Energy 2012 : wie smart ist der Weg zur Energiewende? / Uwe Großmann, Ingo Kunold (Hrsg.) Y1 - 2012 SN - 978-3-86488-030-8 SP - 109 EP - 122 PB - Hülsbusch CY - Glückstadt ER - TY - CHAP A1 - Vismann, Ulrich T1 - Stahlbetonbau T2 - Wendehorst Beispiele aus der Baupraxis. - 4. Aufl. Y1 - 2012 SN - 978-3-8348-0999-5 ; 978-3-8348-8229-5 U6 - http://dx.doi.org/10.1007/978-3-8348-8229-5_9 SP - 223 EP - 262 PB - Springer Vieweg CY - Wiesbaden ER - TY - CHAP A1 - Stroetmann, Richard A1 - Lohse, Wolfram T1 - Stahlbau T2 - Wendehorst Beispiele aus der Baupraxis. - 4. Aufl. Y1 - 2012 SN - 978-3-8348-0999-5 ; 978-3-8348-8229-5 U6 - http://dx.doi.org/10.1007/978-3-8348-8229-5_10 SP - 263 EP - 361 PB - Springer Vieweg CY - Wiesbaden ER - TY - CHAP A1 - Feiser, Johannes T1 - Geotechnik T2 - Wendehorst Beispiele aus der Baupraxis. - 4. Aufl. Y1 - 2012 SN - 978-3-8348-0999-5 ; 978-3-8348-8229-5 U6 - http://dx.doi.org/10.1007/978-3-8348-8229-5_14 SP - 453 EP - 495 PB - Springer Vieweg CY - Wiesbaden ER - TY - CHAP A1 - Strohmeier, Andreas T1 - Siedlungswasserwirtschaft T2 - Wendehorst Beispiele aus der Baupraxis. - 4. Aufl. Y1 - 2012 SN - 978-3-8348-0999-5 ; 978-3-8348-8229-5 U6 - http://dx.doi.org/10.1007/978-3-8348-8229-5_16 SP - 527 EP - 566 PB - Springer Vieweg CY - Wiesbaden ER - TY - CHAP A1 - Biener, Ernst T1 - Abfallwirtschaft T2 - Wendehorst Beispiele aus der Baupraxis. - 4. Aufl. Y1 - 2012 SN - 978-3-8348-0999-5 ; 978-3-8348-8229-5 U6 - http://dx.doi.org/10.1007/978-3-8348-8229-5_17 SP - 567 EP - 603 PB - Springer Vieweg CY - Wiesbaden ER - TY - CHAP A1 - Borchert, Jörg A1 - Lintzel, P. ED - Zenke, Ines T1 - Risiken des Handels T2 - Energiehandel in Europa Y1 - 2012 SN - 978-3-9813142-9-8 SP - 303 EP - 312 PB - Beck CY - München ET - 3. Aufl. ER - TY - CHAP A1 - Borchert, Jörg ED - Zenke, Ines T1 - Aufbau von Handelseinheiten T2 - Energiehandel in Europa Y1 - 2012 SN - 978-3-406-63237-2 SP - 467 EP - 479 PB - Beck CY - München ET - 3. Aufl. ER - TY - CHAP A1 - Borchert, Jörg A1 - Michels, A. ED - Zenke, ines T1 - Beschaffungsstrategien an der Schnittstelle Energiehandel / Vertrieb T2 - Energiehandel in Europa Y1 - 2012 SN - 978-3-406-63237-2 SP - 508 EP - 522 PB - Beck CY - München ET - 3. Aufl. ER - TY - CHAP A1 - Lind, Thorsten Patric T1 - Wirkungen der Eröffnung des Insolvenzverfahrens : §§ 129, 132, 133, 144, 145 T2 - Bankenkommentar zum Insolvenzrecht. - 2. Aufl. Y1 - 2012 SN - 978-3-943170-03-0 SP - 1145 EP - 1585 PB - Finanz Colloquium CY - Heidelberg ER - TY - CHAP A1 - Butenweg, Christoph A1 - Roeser, W. T1 - Erdbebenbemessung von Stahlbetontragwerken nach DIN EN 1998-1 T2 - Stahlbetonbau aktuell : Praxishandbuch Y1 - 2012 SN - 978-3-410-21932-3 (Print) ; 978-341-02193-3-0 (E-Book) SP - A.1 EP - A.43 PB - Beuth CY - Berlin ER - TY - CHAP A1 - Kuhlmann, Wolfram A1 - Butenweg, Christoph A1 - Meskouris, Konstantin A1 - Kempen, Thomas T1 - Simulation des Tragverhaltens des Aachener Doms im Erdbebenfall T2 - Die karolingische Pfalzkapelle in Aachen : Material, Bautechnik, Restaurierung. (Arbeitshefte der rheinischen Denkmalpflege ; 78) Y1 - 2012 SN - 978-3-88462-325-1 SP - 237 EP - 248 PB - Wernersche Verlags-Gesellschaft CY - Worms ER - TY - CHAP A1 - Becker, Jörg A1 - Knackstedt, Ralf A1 - Eggert, Mathias A1 - Fleischer, Stefan T1 - Fachkonzeptionelle Modellierung von Berichtspflichten in Finanzaufsicht und Verwaltung mit dem H2-Toolset T2 - Auf dem Weg zu einer offenen, smarten und vernetzten Verwaltungskultur Y1 - 2012 SN - 978-3-88579-291-8 SP - 83 EP - 94 PB - Gesellschaft für Informatik CY - Bonn ER - TY - CHAP A1 - Borggrafe, Andreas A1 - Ohndorf, Andreas A1 - Dachwald, Bernd A1 - Seboldt, Wolfgang T1 - Analysis of interplanetary solar sail trajectories with attitude dynamics T2 - Dynamics and Control of Space Systems 2012 N2 - We present a new approach to the problem of optimal control of solar sails for low-thrust trajectory optimization. The objective was to find the required control torque magnitudes in order to steer a solar sail in interplanetary space. A new steering strategy, controlling the solar sail with generic torques applied about the spacecraft body axes, is integrated into the existing low-thrust trajectory optimization software InTrance. This software combines artificial neural networks and evolutionary algorithms to find steering strategies close to the global optimum without an initial guess. Furthermore, we implement a three rotational degree-of-freedom rigid-body attitude dynamics model to represent the solar sail in space. Two interplanetary transfers to Mars and Neptune are chosen to represent typical future solar sail mission scenarios. The results found with the new steering strategy are compared to the existing reference trajectories without attitude dynamics. The resulting control torques required to accomplish the missions are investigated, as they pose the primary requirements to a real on-board attitude control system. Y1 - 2012 SN - 978-0-87703-587-9 SP - 1553 EP - 1569 PB - Univelt Inc CY - San Diego ER - TY - CHAP A1 - Frühwald, Katja A1 - Peterson, Leif Arne A1 - Hasenstab, Andreas ED - Fouad, Nabil A. T1 - Prüfverfahren zur Begutachtung der Materialeigenschaften von Holztragwerken T2 - Bauphysik‐Kalender 2012: Schwerpunkt: Gebäudediagnostik N2 - Dieses Kapitel beinhaltet: - Einleitung - Ausgewählte typische Schäden an Holzbauwerken - Das Material Holz und seine Besonderheiten - Bestandserfassung - Labormethoden - Begutachtungsbeispiele - Zusammenfassung und Schlussfolgerungen - Literatur Y1 - 2012 SN - 9783433029862 (Print) SN - 9783433601235 (Online) U6 - http://dx.doi.org/10.1002/9783433601235.ch4 SP - 103 EP - 155 PB - Ernst & Sohn CY - Berlin ER - TY - CHAP A1 - Röth, Thilo A1 - Kampker, Achim A1 - Reisgen, Uwe A1 - Hameyer, Kay A1 - De Doncker, R. W. T1 - Entwicklung von elektrofahrzeugspezifischen Systemen T2 - Elektromobilität : Grundlagen einer Zukunftstechnologie N2 - Die Fahrzeugkarosserie bildet als größte funktionale und organisatorische Systemeinheit ein zentrales Kompetenzfeld der OEMs. Für den Fahrzeughersteller stellt der Karosserierohbau eine hohe Kernkompetenz sowohl in der Produktentwicklung als auch in der Produktion dar. Neue, innovative Karosseriebauweisen, bspw. aufgrund eines neuen Fahrzeugkonzeptes oder neuer Anforderungen, bedeuten für den OEM auch gleichzeitig die intensive Auseinandersetzung mit Kompetenzfokussierung bzw. Wertschöpfungsverlagerungen. Y1 - 2013 SN - 978-3-642-31986-0 SP - 235 EP - 336 PB - Springer CY - Berlin ER - TY - CHAP A1 - Wolf, Martin A1 - Fräntz, Birgit T1 - Erfolgreiches IT-Marketing T2 - Erfolgreiches IT-Marketing in Zeiten von Social Media, Cloud & Co. - (CIO-Handbuch ; 2) KW - IT-Marketing Y1 - 2013 SN - 978-3-86329-612-4 SP - 123 EP - 140 PB - Symposion Publishing CY - Düsseldorf ET - 1. Auflage ER - TY - CHAP A1 - Lingens, Hans A1 - Vollmann, Andreas T1 - Fügetechnik an der FH Aachen - Aus- und Weiterbildung mit Praxisbezug T2 - Innovation durch Kooperation : wie der Mittelstand durch Zusammenarbeit mit den Hochschulen seine Wettbewerbsfähigkeit steigert : Festschrift für Prof. Dr. rer. nat. Johannes Gartzen / Thomas Gartzen, Ute Gartzen (Hrsg.) Y1 - 2013 SN - 978-3-86359-136-6 N1 - Gedruckt in der Bibliothek unter der Signatur: 21 PZI 73 SP - 123 EP - 127 PB - Apprimus Verlag CY - Aachen ER - TY - CHAP A1 - Thomas, Axel T1 - Unternehmertum als Studienfach?! T2 - Innovation durch Kooperation : wie der Mittelstand durch Zusammenarbeit mit den Hochschulen seine Wettbewerbsfähigkeit steigert : Festschrift für Prof. Dr. rer. nat. Johannes Gartzen / Thomas Gartzen, Ute Gartzen (Hrsg.) Y1 - 2013 SN - 978-3-86359-136-6 SP - 139 EP - 144 PB - Apprimus Verlag CY - Aachen ER - TY - CHAP A1 - Mayer, Claudia T1 - Innovation und Kommunikation T2 - Innovation durch Kooperation : wie der Mittelstand durch Zusammenarbeit mit den Hochschulen seine Wettbewerbsfähigkeit steigert : Festschrift für Prof. Dr. rer. nat. Johannes Gartzen / Thomas Gartzen, Ute Gartzen (Hrsg.) Y1 - 2013 SN - 978-3-86359-136-6 SP - 145 EP - 149 PB - Apprimus Verlag CY - Aachen ER - TY - CHAP A1 - Janser, Frank T1 - Zukunftssicherung im Mittelstand - Kooperation zwischen der Stacke Tresorbau GmbH und der Fachhochschule Aachen T2 - Innovation durch Kooperation : wie der Mittelstand durch Zusammenarbeit mit den Hochschulen seine Wettbewerbsfähigkeit steigert : Festschrift für Prof. Dr. rer. nat. Johannes Gartzen / Thomas Gartzen, Ute Gartzen (Hrsg.) Y1 - 2013 SN - 978-3-86359-136-6 SP - 179 EP - 183 PB - Apprimus Verlag CY - Aachen ER - TY - CHAP A1 - Gebhardt, Andreas T1 - Entwicklung der 3D-Drucktechnologie und Potenziale für die Anwendung im Mittelstand T2 - Innovation durch Kooperation : wie der Mittelstand durch Zusammenarbeit mit den Hochschulen seine Wettbewerbsfähigkeit steigert : Festschrift für Prof. Dr. rer. nat. Johannes Gartzen / Thomas Gartzen, Ute Gartzen (Hrsg.) Y1 - 2013 SN - 978-3-86359-136-6 SP - 55 EP - 59 PB - Apprimus Verlag CY - Aachen ER - TY - CHAP A1 - Cordewiner, Hans-Josef T1 - Konstruktion im Wandel: von der technischen Zeichnung zum 3D-Produktmodell T2 - Innovation durch Kooperation : wie der Mittelstand durch Zusammenarbeit mit den Hochschulen seine Wettbewerbsfähigkeit steigert : Festschrift für Prof. Dr. rer. nat. Johannes Gartzen / Thomas Gartzen, Ute Gartzen (Hrsg.) Y1 - 2013 SN - 978--3-86359-136-6 SP - 115 EP - 121 PB - Apprimus Verlag CY - Aachen ER - TY - CHAP A1 - Dachwald, Bernd A1 - Ulamec, Stephan A1 - Biele, Jens T1 - Clean in situ subsurface exploration of icy environments in the solar system T2 - Habitability of other planets and satellites. - (Cellular origin, life in extreme habitats and astrobiology ; 28) N2 - "To assess the habitability of the icy environments in the solar system, for example, on Mars, Europa, and Enceladus, the scientific analysis of material embedded in or underneath their ice layers is very important. We consider self-steering robotic ice melting probes to be the best method to cleanly access these environments, that is, in compliance with planetary protection standards. The required technologies are currently developed and tested." Y1 - 2013 SN - 978-94-007-6545-0 (Druckausgabe) SN - 978-94-007-6546-7 (E-Book) SP - 367 EP - 397 PB - Springer CY - Dordrecht ER - TY - CHAP A1 - Naujokat, Anke T1 - Schichtung, Überblendung, Collage. Formen und Bedeutungen architektonischer Simultaneität T2 - Simultaneität : Modelle der Gleichzeitigkeit in den Wissenschaften und Künsten Y1 - 2013 SN - 978-3-8376-2261-4 SP - 171 EP - 190 PB - transcript-Verlag CY - Bielefeld ER - TY - CHAP A1 - Schleser, Markus T1 - Fügen für die Elektromobilität T2 - Innovation durch Kooperation : wie der Mittelstand durch Zusammenarbeit mit den Hochschulen seine Wettbewerbsfähigkeit steigert : Festschrift für Prof. Dr. rer. nat. Johannes Gartzen / Thomas Gartzen, Ute Gartzen (Hrsg.) Y1 - 2013 SN - 978-3-86359-136-6 SP - 65 EP - 70 PB - Apprimus Verlag CY - Aachen ER - TY - CHAP A1 - Goldbach, Daniel T1 - Diagnosemaßnahmen in der funktionalen Sicherheit T2 - Diagnose in mechatronischen Fahrzeugsystemen, VI : neue Verfahren für Test, Prüfung und Diagnose von E/E-Systemen im Kfz : 7. Tagung "Diagnose in Mechatronischen Fahrzeugsystemen". Bernhard Bäker ... (Hrsg.) Y1 - 2013 SN - 978-3-8169-3221-5 SP - 179 EP - 198 PB - Expert Verlag CY - Renningen ER - TY - CHAP A1 - Alexopoulos, Spiros T1 - Biomass technology and bio-fuels: Heating/cooling and power T2 - Renewable energy systems : theory, innovations, and intelligent applications / eds.: Socrates Kaplanis and Eleni Kaplani Y1 - 2013 SN - 9781624177415 SP - 501 EP - 523 PB - Nova Science Publ. CY - Hauppauge, NY ER - TY - CHAP A1 - Fabo, Sabine ED - Kacunko, Slavko T1 - Portrait of the artist as a spoilsport : Marcel Odenbach's concept of detachment T2 - Take it or leave it : Marcel Odenbach - anthology of texts and videos. - (eva - edition video art ; 2) Y1 - 2013 SN - 978-3-8325-3386-1 SP - 11 EP - 29 PB - Logos CY - Berlin ER - TY - CHAP A1 - Priede, Gareth A1 - Ferrein, Alexander T1 - Towards passive walking for the fully-actuated biped robot Nao T2 - Emerging trends in computing, informatics, systems sciences, and engineering. (Lecture notes in electrical engineering : vol. 151) N2 - Many biped robots deploy a form of gait that follows the zero moment point (ZMP) approach, that is, the robot is in a stable position at any point in time. This requires the robot to be fully actuated. While very stable, the draw-backs of this approach are a fairly slow gait and high energy consumption. An alternative approach is the so-called passive-dynamic walking, where the gait makes use of the inertia and dynamic stability of the robot. In this paper we describe our ongoing work of combining the principles of passive-dynamic walking on the fully-actuated biped robot Nao, which is also deployed for robotic soccer applications. We present a simple controller that allows the robot to stably rock sidewards, showing a closed limit-cycle. We discuss first results of superimposing a forward motion on the sidewards motion. Based on this we expect to endow the Nao with a fast, robust, and stable passive-dynamic walk on the fully-actuated Nao in the future. Y1 - 2013 SN - 978-1-4614-3557-0 ; 978-1-4614-3558-7 U6 - http://dx.doi.org/10.1007/978-1-4614-3558-7_18 SP - 225 EP - 236 PB - Springer CY - New York, NY ER - TY - CHAP A1 - Hoepner, Gert A1 - Schminke, Lutz H. T1 - Dialog-Marketing – 2 in 1 – mehr als 3-fach erfolgreich T2 - Marketing in Forschung und Praxis : [Jubiläumsausgabe zum 40-jährigen Bestehen der Arbeitsgemeinschaft für Marketing] / hrsg. von Günter Hofbauer ... Y1 - 2013 SN - 978-3-942171-98-4 SP - 375 EP - 396 PB - Uni-Ed. CY - Berlin ER - TY - CHAP A1 - Schmidt, Herbert T1 - Finanzierungspartnerwahl durch mittelständische Unternehmen T2 - Innovation durch Kooperation : wie der Mittelstand durch Zusammenarbeit mit den Hochschulen seine Wettbewerbsfähigkeit steigert ; Festschrift für Prof. Dr. rer. nat. Johannes Gartzen / Thomas Gartzen, Ute Gartzen (Hrsg.) Y1 - 2013 SN - 978-3-86359-136-6 SP - 163 EP - 166 PB - Apprimus Verlag CY - Aachen ER - TY - CHAP A1 - Pietsch, Wolfram T1 - A framework for strategic positioning of IT-products T2 - Software business : from physical products to software services and solutions : 4th International Conference on Software Business, ICSOB 2013; Potsdam; Germany; 11 June 2013 through 14 June 2013. (Lecture notes in business information processing ; 150) N2 - IT Products are viewed and managed differently depending on the perspectives and the stage within the life cycle. A model is presented that integrates different perspectives and stages serving as an aid for the analysis of business models and focused positioning of IT-products. Four generic business models are analysed with regard to the product management function in general and the positioning field for IT-products specifically: off-the-shelf (license), license plus service, project, and system service (incl. cloud computing). KW - Strategic Business Planning KW - IT Products KW - Business Models KW - Product Management Y1 - 2013 U6 - http://dx.doi.org/10.1007/978-3-642-39336-5_11 SP - 102 EP - 116 PB - Springer CY - Berlin ER - TY - CHAP A1 - Bialonski, Stephan A1 - Lehnertz, Klaus T1 - From time series to complex networks: an overview T2 - Recent Advances in Predicting and Preventing Epileptic Seizures: Proceedings of the 5th International Workshop on Seizure Prediction N2 - The network approach towards the analysis of the dynamics of complex systems has been successfully applied in a multitude of studies in the neurosciences and has yielded fascinating insights. With this approach, a complex system is considered to be composed of different constituents which interact with each other. Interaction structures can be compactly represented in interaction networks. In this contribution, we present a brief overview about how interaction networks are derived from multivariate time series, about basic network characteristics, and about challenges associated with this analysis approach. Y1 - 2013 SN - 978-981-4525-36-7 U6 - http://dx.doi.org/10.1142/9789814525350_0010 SP - 132 EP - 147 ER - TY - CHAP A1 - Kirsch, Hans-Jürgen A1 - Bassen, Yasmine T1 - IGW RS HFA 21 : konzeptionelle Lösung oder Einzelfall? ; Erfolg bei Spenden sammelnden Organisationen ; eine bilanztheoretische Untersuchung T2 - Jahrbuch für Controlling und Rechnungswesen. Vol. 29 Y1 - 2013 SP - 355 EP - 369 PB - LexisNexis, ARD Orac CY - Wien ER - TY - CHAP A1 - Matcha, Heike A1 - Karzel, Rüdiger A1 - Pahl, Katja-Annika T1 - Lehre als Praxis als Forschung: 1:1 Entwicklung von Messeständen unter Einsatz parametrisierter Software und computergesteuerter Herstellung T2 - ECHT?! Zum Bezug von Praxis und Lehre in der Architekturausbildung Y1 - 2013 SN - 978-3-94433111-9 SP - 95 EP - 108 PB - TUDpress - Verlag der Wissenschaften CY - Dresden ER - TY - CHAP A1 - Stangel-Meseke, Martina A1 - Hahn, Pia A1 - Steuer-Dankert, Linda T1 - Balance durch Diversity Management : Lösungsansätze für unternehmerische Herausforderungen aus Megatrends T2 - Balance Management N2 - Unsere unternehmerische Umwelt befindet sich in einem zunehmend dynamischen Wandel. Dies führt dazu, dass Herausforderungen, denen sich Unternehmen stellen müssen, immer komplexer werden. Hier gilt es zunehmend, eine Balance zwischen verschiedenen Spannungsfeldern zu erreichen. Sogenannte Megatrends stellen die Treiber dieses Wandels dar. Als Megatrend werden nach dem Zukunftsinstitut (2010a) richtungsweisende Veränderungstendenzen aufgefasst, die alle Bereiche des Lebens sowohl individuell als auch gesellschaftlich beeinflussen und langfristige Auswirkungen haben. Y1 - 2013 SN - 978-3-658-02191-7 U6 - http://dx.doi.org/10.1007/978-3-658-02192-4_6 SP - 145 EP - 166 PB - Springer Gabler CY - Wiesbaden ER - TY - CHAP A1 - Blome, Hans-Joachim T1 - Die Tragweite der physikalischen Kosmologie T2 - Exploring Uncertainty Y1 - 2013 SN - 978-3-658-00897-0 U6 - http://dx.doi.org/10.1007/978-3-658-00897-0_6 SP - 105 EP - 150 PB - Springer Gabler CY - Wiesbaden ER - TY - CHAP A1 - Bozakov, Zdravko A1 - Sander, Volker T1 - OpenFlow: A Perspective for Building Versatile Networks T2 - Network-Embedded Management and Applications Y1 - 2013 SN - 978-1-4419-6769-5 U6 - http://dx.doi.org/10.1007/978-1-4419-6769-5_11 SP - 217 EP - 245 PB - Springer CY - New York, NY ER - TY - CHAP A1 - Finkenberger, Isabel Maria ED - Bredenbeck, Martin T1 - Vox populi. (Transformations-)potenziale nachkriegsmoderner Freiraumressourcen T2 - Grün modern - Gärten und Parks der 1950er bis 1970er Jahre Y1 - 2024 SN - 9783925374357 N1 - Ein Kulturerbe als Herausforderung für Denkmalpflege und Vermittlungsarbeit ; Dokumentation der Tagung am 15. und 16. Oktober 2013 in Hamburg SP - 31 EP - 38 PB - BHU CY - Bonn ER - TY - CHAP A1 - Tran, Thanh Ngoc A1 - Staat, Manfred T1 - Shakedown analysis of Reissner-Mindlin plates using the edge-based smoothed finite element method T2 - Direct methods for limit states in structures and materials / Dieter Weichert ; Alan Ponter, ed. N2 - This paper concerns the development of a primal-dual algorithm for limit and shakedown analysis of Reissner-Mindlin plates made of von Mises material. At each optimization iteration, the lower bound of the shakedown load multiplier is calculated simultaneously with the upper bound using the duality theory. An edge-based smoothed finite element method (ES-FEM) combined with the discrete shear gap (DSG) technique is used to improve the accuracy of the solutions and to avoid the transverse shear locking behaviour. The method not only possesses all inherent features of convergence and accuracy from ES-FEM, but also ensures that the total number of variables in the optimization problem is kept to a minimum compared with the standard finite element formulation. Numerical examples are presented to demonstrate the effectiveness of the present method. Y1 - 2014 SN - 978-94-007-6826-0 (Print) 978-94-007-6827-7 (Online) U6 - http://dx.doi.org/10.1007/978-94-007-6827-7_5 SP - 101 EP - 117 PB - Springer CY - Dordrecht [u.a.] ER - TY - CHAP A1 - Wolff, Nino A1 - Seefeldt, Patric A1 - Bauer, Wolfgang A1 - Fiebig, Christopher A1 - Gerding, Patrick A1 - Parow-Souchon, Kai A1 - Pongs, Anna A1 - Reiffenrath, Matti A1 - Ziemann, Thomas T1 - Alternative application of solar sail technology T2 - Advances in solar sailing N2 - The development of Gossamer sail structures for solar sails contributes to a large field of future space applications like thin film solar generators, membrane antennas and drag sails. The focus of this paper is the development of a drag sail based on solar sail technology that could contribute to a reduction of space debris in low Earth orbits. The drag sail design and its connections to solar sail development, a first test on a sounding rocket, as well as the ongoing integration of the drag sail into a triple CubeSat is presented. Y1 - 2014 SN - 978-3-642-34906-5 (Print) ; 978-3-642-34907-2 (E-Book) U6 - http://dx.doi.org/10.1007/978-3-642-34907-2_23 SP - 351 EP - 365 PB - Springer CY - Berlin ER - TY - CHAP A1 - Dachwald, Bernd A1 - Boehnhardt, Herrmann A1 - Broj, Ulrich A1 - Geppert, Ulrich R. M. E. A1 - Grundmann, Jan-Thimo A1 - Seboldt, Wolfgang A1 - Seefeldt, Patric A1 - Spietz, Peter A1 - Johnson, Les A1 - Kührt, Ekkehard A1 - Mottola, Stefano A1 - Macdonald, Malcolm A1 - McInnes, Colin R. A1 - Vasile, Massimiliano A1 - Reinhard, Ruedeger T1 - Gossamer roadmap technology reference study for a multiple NEO Rendezvous Mission T2 - Advances in solar sailing N2 - A technology reference study for a multiple near-Earth object (NEO) rendezvous mission with solar sailcraft is currently carried out by the authors of this paper. The investigated mission builds on previous concepts, but adopts a strong micro-spacecraft philosophy based on the DLR/ESA Gossamer technology. The main scientific objective of the mission is to explore the diversity of NEOs. After direct interplanetary insertion, the solar sailcraft should—within less than 10 years—rendezvous three NEOs that are not only scientifically interesting, but also from the point of human spaceight and planetary defense. In this paper, the objectives of the study are outlined and a preliminary potential mission profile is presented. Y1 - 2014 SN - 978-3-642-34906-5 (Print) ; 978-3-642-34907-2 (E-Book) SP - 211 EP - 226 PB - Springer CY - Berlin [u.a.] ER - TY - CHAP A1 - McInnes, Colin R. A1 - Bothmer, Volker A1 - Dachwald, Bernd A1 - Geppert, Ulrich R. M. E. A1 - Heiligers, Jeannette A1 - Hilgers, Alan A1 - Johnson, Les A1 - Macdonald, Malcolm A1 - Reinhard, Ruedeger A1 - Seboldt, Wolfgang A1 - Spietz, Peter T1 - Gossamer roadmap technology reference study for a Sub-L1 Space Weather Mission T2 - Advances in solar sailing N2 - A technology reference study for a displaced Lagrange point space weather mission is presented. The mission builds on previous concepts, but adopts a strong micro-spacecraft philosophy to deliver a low mass platform and payload which can be accommodated on the DLR/ESA Gossamer-3 technology demonstration mission. A direct escape from Geostationary Transfer Orbit is assumed with the sail deployed after the escape burn. The use of a miniaturized, low mass platform and payload then allows the Gossamer-3 solar sail to potentially double the warning time of space weather events. The mission profile and mass budgets will be presented to achieve these ambitious goals. Y1 - 2014 SN - 978-3-642-34906-5 (Print) ; 978-3-642-34907-2 (E-Book) SP - 227 EP - 242 PB - Springer CY - Berlin [u.a.] ER - TY - CHAP A1 - Macdonald, Malcolm A1 - McGrath, C. A1 - Appourchaux, T. A1 - Dachwald, Bernd A1 - Finsterle, W. A1 - Gizon, L. A1 - Liewer, P. C. A1 - McInnes, Colin R. A1 - Mengali, G. A1 - Seboldt, W. A1 - Sekii, T. A1 - Solanki, S. K. A1 - Velli, M. A1 - Wimmer-Schweingruber, R. F. A1 - Spietz, Peter A1 - Reinhard, Ruedeger ED - Macdonald, Malcolm T1 - Gossamer roadmap technology reference study for a solar polar mission T2 - Advances in solar sailing N2 - A technology reference study for a solar polar mission is presented. The study uses novel analytical methods to quantify the mission design space including the required sail performance to achieve a given solar polar observation angle within a given timeframe and thus to derive mass allocations for the remaining spacecraft sub-systems, that is excluding the solar sail sub-system. A parametric, bottom-up, system mass budget analysis is then used to establish the required sail technology to deliver a range of science payloads, and to establish where such payloads can be delivered to within a given timeframe. It is found that a solar polar mission requires a solar sail of side-length 100–125 m to deliver a ‘sufficient value’ minimum science payload, and that a 2.5 μm sail film substrate is typically required, however the design is much less sensitive to the boom specific mass. Y1 - 2014 SN - 978-3-642-34906-5 U6 - http://dx.doi.org/10.1007/978-3-642-34907-2_17 SP - 243 EP - 257 PB - Springer CY - Berlin, Heidelberg ER - TY - CHAP A1 - Schöning, Michael Josef A1 - Poghossian, Arshak A1 - Glück, Olaf A1 - Thust, Marion T1 - Electrochemical composition measurement T2 - Measurement, instrumentation, and sensors handbook: electromagnetic, optical, radiation, chemical, and biomedical measuremen Y1 - 2014 SN - 978-1-4398-4891-3 SP - 55-1 EP - 55-54 PB - CRC Pr. CY - Boca Raton, Fa. ET - 2nd ed. ER - TY - CHAP A1 - Schmidt, Herbert T1 - Angst vor Zukunft, Lust auf Zukunft T2 - Re|peat-Jahrbuch Treasury und Private Banking : Produkte, Märkte und Strategien zum Nachschlagen und Verstehen Y1 - 2014 SP - 255 EP - 269 PB - Roland Eller CY - Potsdam ER - TY - CHAP A1 - Poghossian, Arshak A1 - Weiland, Maryam A1 - Schöning, Michael Josef ED - Lvova, Larisa ED - Kirsanov, Dmitry ED - di Natale, Corrado ED - Legin, Audrey T1 - Nanoplate field-effect capacitors: a new transducer structure for multiparameter (bio-)chemical sensing T2 - Multisensor system for chemical analysis : materials and sensors N2 - An array of electrically isolated nanoplate field-effect silicon-on-insulator (SOI) capacitors as a new transducer structure for multiparameter (bio-)chemical sensing is presented. The proposed approach allows addressable biasing and electrical readout of multiple nanoplate field-effect capacitive (bio-)chemical sensors on the same SOI chip, as well as differential-mode measurements. The realized sensor chip has been applied for pH and penicillin concentration measurements, electrical monitoring of polyelectrolyte multilayer formation, and the label-free electrical detection of consecutive deoxyribonucleic acid (DNA) hybridization and denaturation events. Y1 - 2014 SN - 978-981-4411-15-8 ; 978-981-4411-16-5 U6 - http://dx.doi.org/10.1201/b15491-11 SP - 333 EP - 373 PB - Jenny Stanford Publishing CY - Singapore ET - 1 ER - TY - CHAP A1 - Laack, Walter van T1 - Gefahren heutiger neurologischer Schlussfolgerungen für ethische Verantwortung T2 - Ethik und Moral in Staat, Wirtschaft und Gesellschaft : 5. Rotary-Tag, 14.-15.2.2014, Kleve Y1 - 2014 SN - 978-3-944011-21-9 SP - 98 EP - 114 PB - Edition Virgines CY - Lingen ER - TY - CHAP A1 - Laack, Walter van T1 - Zu neuen wissenschaftlichen Erkenntnissen zur Vereinbarkeit von Vernunft und Glaube T2 - Ethik und Moral in Staat, Wirtschaft und Gesellschaft : 5. Rotary-Tag, 14.-15.2.2014, Kleve Y1 - 2014 SN - 978-3-944011-21-9 SP - 152 EP - 162 PB - Edition Virgines CY - Lingen ER - TY - CHAP A1 - Niemüller, Tim A1 - Ewert, Daniel A1 - Reuter, Sebastian A1 - Ferrein, Alexander A1 - Jeschke, Sabina A1 - Lakemeyer, Gerhard T1 - RoboCup logistics league sponsored by festo: A competitive factory automation testbed T2 - RoboCup 2013: Robot World Cup XVII : Eindhoven; Netherlands; 1 July 2013 through 1 July 2013. (Lecture notes in computer science ; 8371) N2 - A new trend in automation is to deploy so-called cyber-physical systems (CPS) which combine computation with physical processes. The novel RoboCup Logistics League Sponsored by Festo (LLSF) aims at such CPS logistic scenarios in an automation setting. A team of robots has to produce products from a number of semi-finished products which they have to machine during the game. Different production plans are possible and the robots need to recycle scrap byproducts. This way, the LLSF is a very interesting league offering a number of challenging research questions for planning, coordination, or communication in an application-driven scenario. In this paper, we outline the objectives of the LLSF and present steps for developing the league further towards a benchmark for logistics scenarios for CPS. As a major milestone we present the new automated referee system which helps in governing the game play as well as keeping track of the scored points in a very complex factory scenario. Y1 - 2014 SN - 978-3-662-44467-2 (Print) 978-3-662-44468-9 (Online) SP - 336 EP - 347 PB - Springer CY - Berlin ER - TY - CHAP A1 - Reichert, Walter T1 - Der Vertriebsingenieur: Ausbildung und Beruf T2 - Berufsstart Technik : das Karriereportal für junge Akademiker ; Ingenieure, Naturwissenschaftler, Informatiker Y1 - 2014 SP - 456 EP - 458 PB - Resch CY - Großenkneten ER - TY - CHAP A1 - Kirchner, Patrick A1 - Reisert, Steffen A1 - Schöning, Michael Josef T1 - Calorimetric gas sensors for hydrogen peroxide monitoring in aseptic food processes T2 - Gas sensing fundamentals. (Springer Series on Chemical Sensors and Biosensors ; 15) N2 - For the sterilisation of aseptic food packages it is taken advantage of the microbicidal properties of hydrogen peroxide (H2O2). Especially, when applied in vapour phase, it has shown high potential of microbial inactivation. In addition, it offers a high environmental compatibility compared to other chemical sterilisation agents, as it decomposes into oxygen and water, respectively. Due to a lack in sensory detection possibilities, a continuous monitoring of the H2O2 concentration was recently not available. Instead, the sterilisation efficacy is validated using microbiological tests. However, progresses in the development of calorimetric gas sensors during the last 7 years have made it possible to monitor the H2O2 concentration during operation. This chapter deals with the fundamentals of calorimetric gas sensing with special focus on the detection of gaseous hydrogen peroxide. A sensor principle based on a calorimetric differential set-up is described. Special emphasis is given to the sensor design with respect to the operational requirements under field conditions. The state-of-the-art regarding a sensor set-up for the on-line monitoring and secondly, a miniaturised sensor for in-line monitoring are summarised. Furthermore, alternative detection methods and a novel multi-sensor system for the characterisation of aseptic sterilisation processes are described. KW - Calorimetric gas sensor KW - Hydrogen peroxide KW - Multi-sensor system Y1 - 2014 SN - 978-3-642-54518-4 (Print) ; 978-3-642-54519-1 (Online) U6 - http://dx.doi.org/10.1007/5346_2013_51 SP - 279 EP - 309 PB - Springer CY - Heidelberg ER - TY - CHAP A1 - Schöning, Michael Josef A1 - Poghossian, Arshak A1 - Glück, Olaf A1 - Thust, Marion T1 - Electrochemical methods for the determination of chemical variables in aqueous media T2 - Measurement, instrumentation, and sensors handbook / ed. by John G. Webster [u.a.] Vol. 2 : Electromagnetic, optical, radiation, chemical, and biomedical measurement Y1 - 2014 SN - 978-1-4398-4891-3 SP - 55-1 EP - 55-54 PB - CRC Pr. CY - Boca Raton, Fla. ER - TY - CHAP A1 - Knott, Thomas C. A1 - Sofronia, Raluca E. A1 - Gerressen, Marcus A1 - Law, Yuen A1 - Davidescu, Arjana A1 - Savii, George G. A1 - Gatzweiler, Karl-Heinz A1 - Staat, Manfred A1 - Kuhlen, Torsten W. T1 - Preliminary bone sawing model for a virtual reality-based training simulator of bilateral sagittal split osteotomy T2 - Biomedical simulation : 6th International Symposium, ISBMS 2014, Strasbourg, France, October 16-17, 2014 : proceedings (Lecture notes in computer science : vol. 8789) N2 - Successful bone sawing requires a high level of skill and experience, which could be gained by the use of Virtual Reality-based simulators. A key aspect of these medical simulators is realistic force feedback. The aim of this paper is to model the bone sawing process in order to develop a valid training simulator for the bilateral sagittal split osteotomy, the most often applied corrective surgery in case of a malposition of the mandible. Bone samples from a human cadaveric mandible were tested using a designed experimental system. Image processing and statistical analysis were used for the selection of four models for the bone sawing process. The results revealed a polynomial dependency between the material removal rate and the applied force. Differences between the three segments of the osteotomy line and between the cortical and cancellous bone were highlighted. KW - Bone sawing KW - virtual reality KW - training simulator Y1 - 2014 SN - 978-3-319-12057-7 (Online) SN - 978-3-319-12056-0 (Print) U6 - http://dx.doi.org/10.1007/978-3-319-12057-7_1 SP - 1 EP - 10 PB - Springer CY - Cham ER - TY - CHAP A1 - Timme, Michael T1 - Begriffsbestimmungen T2 - Wohnungseigentumsgesetz : Gesetz über das Wohnungseigentum und das Dauerwohnrecht ; Kommentar Y1 - 2014 SN - 978-3-406-66025-2 SP - 1 EP - 23 PB - Beck CY - München ET - 2. Auflage ER - TY - CHAP A1 - Alhwarin, Faraj A1 - Ferrein, Alexander A1 - Scholl, Ingrid T1 - IR stereo kinect: improving depth images by combining structured light with IR stereo T2 - PRICAI 2014: Trends in artificial intelligence : 13th Pacific Rim International Conference on Artificial Intelligence : Gold Coast, QLD, Australia, December 1-5, 2014 : proceedings. (Lecture notes in computer science ; vol. 8862) N2 - RGB-D sensors such as the Microsoft Kinect or the Asus Xtion are inexpensive 3D sensors. A depth image is computed by calculating the distortion of a known infrared light (IR) pattern which is projected into the scene. While these sensors are great devices they have some limitations. The distance they can measure is limited and they suffer from reflection problems on transparent, shiny, or very matte and absorbing objects. If more than one RGB-D camera is used the IR patterns interfere with each other. This results in a massive loss of depth information. In this paper, we present a simple and powerful method to overcome these problems. We propose a stereo RGB-D camera system which uses the pros of RGB-D cameras and combine them with the pros of stereo camera systems. The idea is to utilize the IR images of each two sensors as a stereo pair to generate a depth map. The IR patterns emitted by IR projectors are exploited here to enhance the dense stereo matching even if the observed objects or surfaces are texture-less or transparent. The resulting disparity map is then fused with the depth map offered by the RGB-D sensor to fill the regions and the holes that appear because of interference, or due to transparent or reflective objects. Our results show that the density of depth information is increased especially for transparent, shiny or matte objects. Y1 - 2014 SN - 978-3-319-13559-5 (Print) ; 978-3-319-13560-1 (E-Book) U6 - http://dx.doi.org/10.1007/978-3-319-13560-1_33 SP - 409 EP - 421 PB - Springer CY - München ER - TY - CHAP A1 - Hebel, Christoph T1 - Mehrwert T2 - Unser Dorf hat Zukunft Y1 - 2014 SP - 6 EP - 7 PB - StädteRegion Aachen CY - Aachen ER - TY - CHAP A1 - Benner, Joachim T1 - Berechnungsmethoden der Wälzlagerreibung und Einflussgrößen T2 - SMK 2014 : Schweizer Maschinenelemente Kolloquim 25. und 26. November 2014 Y1 - 2014 SN - 978-3-944331-81-2 SP - 151 EP - 170 PB - TUDpress Verl. der Wissenschaften CY - Dresden ER - TY - CHAP A1 - Heuermann, Holger A1 - Finger, Torsten ED - Günther, Michael T1 - Microwave Spark Plug for Very High-Pressure Conditions T2 - Ignition systems for gasoline engines Y1 - 2014 SP - 269 EP - 282 PB - DCM Druck CY - Meckenheim ER - TY - CHAP A1 - Borchert, Jörg A1 - Bremen, Frank T1 - Geschäfts- und Organisationsmodelle für ein Strom- und Gas-Portfoliomanagement T2 - Optimierte Strom- und Gasbeschaffung in der Energiewirtschaftsbranche Y1 - 2014 SN - 978-3-9813142-9-8 SP - 11 EP - 28 PB - KS-Energy-Verl. CY - Berlin ER - TY - CHAP A1 - Burger, Ulrich A1 - Kirsch, Ansgar A1 - Marcher, Thomas A1 - Höser, Sebastian T1 - Geologisch-geotechnischer Planungsprozess von Tunnelbauten mit Schwerpunkt tiefliegender Tunnel T2 - Beton-Kalender ; Bd. 103: Unterirdisches Bauen, Grundbau, Eurocode 7 Y1 - 2014 SN - 978-3-433-03051-6 ; 978-3-433-60335-2 ; 978-3-433-60508-0 ; 3-433-60508-4 SP - 37 EP - 62 PB - Ernst CY - Berlin ER - TY - CHAP A1 - Lind, Thorsten Patric T1 - Insolvenzverwalter, Organe der Gläubiger : §§ 56-62, 66-72, 74-79 T2 - Fachanwaltskommentar Insolvenzrecht / hrsg. von Martin Ahrens; Markus Gehrlein; Andreas Ringstmeier . - 2. Aufl. Y1 - 2014 SN - 978-3-472-08559-1 SP - 649 - 703; 728 - 745; 748 - 762 PB - Luchterhand CY - Köln ER - TY - CHAP A1 - Lind, Thorsten Patric T1 - Verwaltung und Verwertung der Insolvenzmasse : §§ 148 - 164 T2 - Fachanwaltskommentar Insolvenzrecht / hrsg. von Martin Ahrens; Markus Gehrlein; Andreas Ringstmeier . - 2. Aufl. Y1 - 2014 SN - 978-3-472-08559-1 SP - 1317 EP - 1356 PB - Luchterhand CY - Köln ER - TY - CHAP A1 - Butenweg, Christoph A1 - Norda, H. T1 - Erdbebenberechnung von Mauerwerksbauten nach DIN EN 1998-1:2010-12 T2 - Mauerwerksbau-Praxis nach Eurocode / Schubert, Schneider, Schoch (Hrsg.). - 3., vollständig überarbeitete Auflage Y1 - 2014 SN - 978-3-410-22739-7 SP - 367 EP - 412 PB - Beuth CY - Berlin, Wien, Zürich ER - TY - CHAP A1 - Altay, Okyay A1 - Taddei, Francesca A1 - Butenweg, Christoph A1 - Klinkel, Sven T1 - Vibration mitigation of wind turbine towers with tuned mass dampers T2 - Wind turbine control and monitoring. (Advances in industrial control) N2 - Because of its minor environmental impact, electricity generation using wind power is getting remarkable. The further growth of the wind industry depends on technological solutions to the challenges in production and construction of the turbines. Wind turbine tower vibrations, which limit power generation efficiency and cause fatigue problems with high maintenance costs, count as one of the main structural difficulties in the wind energy sector. To mitigate tower vibrations auxiliary measures are necessary. The effectiveness of tuned mass damper is verified by means of a numeric study on a 5 MW onshore reference wind turbine. Hereby, also seismic-induced vibrations and soil–structure interaction are considered. Acquired results show that tuned mass damper can effectively reduce resonant tower vibrations and improve the fatigue life of wind turbines. This chapter is also concerned with tuned liquid column damper and a semiactive application of it. Due to its geometric versatility and low prime costs, tuned liquid column dampers are a good alternative to other damping measures, in particular for slender structures like wind turbines. Y1 - 2014 SN - 978-3-319-08412-1 (Print) ; 978-3-319-08413-8 (E-Book) U6 - http://dx.doi.org/10.1007/978-3-319-08413-8_12 SP - 337 EP - 373 PB - Springer CY - Cham ; Heidelberg ; New York ; Dordrecht ; London ER - TY - CHAP A1 - Butenweg, Christoph A1 - Klinkel, Sven T1 - Dynamisches Verhalten von Stahlbetonplatten unter Impact-Belastungen T2 - Massivbau im Wandel : Festschrift zum 60. Geburtstag von Josef Hegger Y1 - 2014 SN - 3-939051-20-9 SP - 369 EP - 380 PB - Ernst CY - Berlin ER - TY - CHAP A1 - Kroll-Ludwigs, Kathrin ED - Ermann, Walter, ED - Grunewald, Barbara ED - Maier-Reimer, Georg T1 - Vorbemerkung vor § 1353 T2 - Erman, Bürgerliches Gesetzbuch : Handkommentar mit AGG, EGBGB (Auszug) , ErbbauRG, LPartG, ProdHaftG, VBVG, VersAus-glG und WEG Y1 - 2014 SN - 978-3-50447-102-6 PB - Verlag Dr. Otto Schmidt CY - Köln ER - TY - CHAP A1 - Kroll-Ludwigs, Kathrin ED - Ermann, Walter ED - Grunewald, Barbara ED - Maier-Reimer, Georg T1 - Vorbemerkung vor § 1297 T2 - Bürgerliches Gesetzbuch : Handkommentar mit AGG, EGBGB (Auszug), ErbbauRG, HausratsVO, LPartG, ProdHaftG, UKlaG, VAHRG und WEG Y1 - 2014 SN - 978-3-504-47102-6 PB - Verlag Dr. Otto Schmidt CY - Köln ER - TY - CHAP A1 - Kroll-Ludwigs, Kathrin T1 - Einleitung vor § 1297 T2 - Bürgerliches Gesetzbuch : Handkommentar mit AGG, EGBGB (Auszug), ErbbauRG, HausratsVO, LPartG, ProdHaftG, UKlaG, VAHRG und WEG Y1 - 2014 SN - 978-3-504-47102-6 PB - Verlag Dr. Otto Schmidt CY - Köln ER - TY - CHAP A1 - Frotscher, Ralf A1 - Goßmann, Matthias A1 - Raatschen, Hans-Jürgen A1 - Temiz Artmann, Aysegül A1 - Staat, Manfred T1 - Simulation of cardiac cell-seeded membranes using the edge-based smoothed FEM T2 - Shell and membrane theories in mechanics and biology. (Advanced structured materials ; 45) N2 - We present an electromechanically coupled Finite Element model for cardiac tissue. It bases on the mechanical model for cardiac tissue of Hunter et al. that we couple to the McAllister-Noble-Tsien electrophysiological model of purkinje fibre cells. The corresponding system of ordinary differential equations is implemented on the level of the constitutive equations in a geometrically and physically nonlinear version of the so-called edge-based smoothed FEM for plates. Mechanical material parameters are determined from our own pressure-deflection experimental setup. The main purpose of the model is to further examine the experimental results not only on mechanical but also on electrophysiological level down to ion channel gates. Moreover, we present first drug treatment simulations and validate the model with respect to the experiments. Y1 - 2015 SN - 978-3-319-02534-6 ; 978-3-319-02535-3 SP - 187 EP - 212 PB - Springer CY - Heidelberg ER - TY - CHAP A1 - Tran, Thanh Ngoc A1 - Staat, Manfred T1 - Uncertainty multimode failure and shakedown analysis of shells T2 - Direct methods for limit and shakedown analysis of structures / eds. Paolo Fuschi ... N2 - This paper presents a numerical procedure for reliability analysis of thin plates and shells with respect to plastic collapse or to inadaptation. The procedure involves a deterministic shakedown analysis for each probabilistic iteration, which is based on the upper bound approach and the use of the exact Ilyushin yield surface. Probabilistic shakedown analysis deals with uncertainties originated from the loads, material strength and thickness of the shell. Based on a direct definition of the limit state function, the calculation of the failure probability may be efficiently solved by using the First and Second Order Reliability Methods (FORM and SORM). The problem of reliability of structural systems (series systems) is handled by the application of a special technique which permits to find all the design points corresponding to all the failure modes. Studies show, in this case, that it improves considerably the FORM and SORM results. KW - Limit analysis KW - Shakedown analysis KW - Reliability analysis KW - Multimode failure KW - Non-linear optimization Y1 - 2015 SN - 978-3-319-12927-3 (print) ; 978-3-319-12928-0 (online) U6 - http://dx.doi.org/10.1007/978-3-319-12928-0_14 SP - 279 EP - 298 PB - Springer CY - Cham ER - TY - CHAP A1 - Vismann, Ulrich T1 - Beton T2 - Wendehorst bautechnische Zahlentafeln / hrsg. von Ulrich Vismann. Ernst Biener ... 35. Aufl. Y1 - 2015 SN - 978-3-658-01689-0 ; 978-3-410-24199-7 U6 - http://dx.doi.org/10.1007/978-3-658-01689-0_11 SP - 477 EP - 495 PB - Springer Vieweg CY - Wiesbaden ER - TY - CHAP A1 - Vismann, Ulrich T1 - Stahlbeton und Spannbeton nach Eurocode 2 T2 - Wendehorst bautechnische Zahlentafeln / hrsg. von Ulrich Vismann. Ernst Biener ... 35. Aufl. Y1 - 2015 SN - 978-3-658-01689-0 ; 978-3-410-24199-7 U6 - http://dx.doi.org/10.1007/978-3-658-01689-0_12 SP - 497 EP - 655 PB - Springer Vieweg CY - Wiesbaden ER - TY - CHAP A1 - Stroetmann, Richard A1 - Lohse, Wolfram ED - Vismann, Ulrich T1 - Stahlbau T2 - Wendehorst bautechnische Zahlentafeln / 35. Auflage N2 - Es ist zwischen Stählen bis S460 und solchen mit höherer Streckgrenze zu unterscheiden. Stähle bis S460 sind auch für die plastische Tragwerksberechnung nach dem Fließgelenkverfahren zugelassen. Bei Stählen oberhalb S460 bis S700 ist neben der elastischen eine nichtlineare plastische Tragwerksberechnung unter Berücksichtigung von Teilplastizierungen von Bauteilen in Fließzonen möglich. Y1 - 2015 SN - 978-3-658-01689-0 ; 978-3-410-24199-7 U6 - http://dx.doi.org/10.1007/978-3-658-01689-0_13 SP - 657 EP - 859 PB - Springer Vieweg CY - Wiesbaden ER - TY - CHAP A1 - Feiser, Johannes ED - Vismann, Ulrich T1 - Geotechnik T2 - Wendehorst Bautechnische Zahlentafeln / 35. Auflage N2 - In der nationalen und der europäischen Normung werden die geotechnischen Aufgaben zwecks Mindestanforderungen an Baugrunduntersuchung, rechnerische Nachweise und Überwachung der Ausführung in drei Klassen (Kategorien) eingeteilt. Sie richten sich nach der zu erwartenden Reaktion des Baugrundes, nach dem geotechnischen Schwierigkeitsgrad des Tragwerks und seiner Einflüsse auf die Umgebung. In DIN 4020 wurde die Einteilung bezüglich Art und Umfang der geotechnischen Untersuchungen bereits verbindlich eingeführt. Y1 - 2015 SN - 978-3-658-01688-3 (Print) SN - 978-3-658-01689-0 (Online) U6 - http://dx.doi.org/10.1007/978-3-658-01689-0_17 SP - 1019 EP - 1101 PB - Springer Vieweg CY - Wiesbaden ER - TY - CHAP A1 - Vismann, Ulrich A1 - Schüller, Michael T1 - Stahlbetonbau T2 - Wendehorst Beispiele aus der Baupraxis. / 5. Auflage N2 - Das Kapitel Stahlbetonbau besteht aus einer Formelsammlung (Teil A) sowie einem Praxisbeispiel (Teil B). In dem Praxisbeispiel werden exemplarisch die erforderlichen Rechenschritte und Nachweise zur Bemessung im GZT und GZG nach Eurocode 2 [1] vorgestellt. Die Hinweise im Text beziehen sich, soweit nicht explizit erwähnt, auf Wendehorst, Bautechnische Zahlentafeln, 35. Auflage, „Stahlbeton- und Spannbetonbau nach Eurocode 2“ [2]. Die zum Praxisbeispiel zugehörigen Konstruktions- und Bewehrungszeichnungen stehen im Onlineportal zu diesem Buch zum kostenlosen Download bereit (siehe unter www.springer.com). Y1 - 2015 SN - 978-3-658-01680-7 ; 978-3-658-01681-4 U6 - http://dx.doi.org/10.1007/978-3-658-01681-4_9 SP - 243 EP - 322 PB - Springer Vieweg CY - Wiesbaden ER - TY - CHAP A1 - Stroetmann, Richard A1 - Lohse, Wolfram T1 - Stahlbau T2 - Wendehorst Beispiele aus der Baupraxis. / 5. Auflage Y1 - 2015 SN - 978-3-658-01689-0 ; 978-3-410-24199-7 U6 - http://dx.doi.org/10.1007/978-3-658-01681-4_10 SP - 323 EP - 431 PB - Springer Vieweg CY - Wiesbaden ER - TY - CHAP A1 - Feiser, Johannes T1 - Geotechnik T2 - Wendehorst Beispiele aus der Baupraxis. / 5. Auflage Y1 - 2015 SN - 978-3-658-01689-0 ; 978-3-410-24199-7 U6 - http://dx.doi.org/10.1007/978-3-658-01681-4_14 SP - 547 EP - 598 PB - Springer Vieweg CY - Wiesbaden ER - TY - CHAP A1 - Strohmeier, Andreas T1 - Siedlungswasserwirtschaft T2 - Wendehorst Beispiele aus der Baupraxis. / 5. Auflage N2 - Nachfolgende Ausführungen und Berechnungsbeispiele beziehen sich auf Kapitel 19 Siedlungswasserwirtschaft im „Wendehorst: Bautechnische Zahlentafeln 35. Auflage 2015“ (abgekürzt: BZ). Für den Bau von Anlagen der Siedlungswasserwirtschaft sind ebenso die Grundlagen der Hydraulik zu berücksichtigen. Aus diesem Grunde sind auch die entsprechenden Ausführungen zur Hydraulik zu beachten. Y1 - 2015 SN - 978-3-658-01689-0 ; 978-3-410-24199-7 U6 - http://dx.doi.org/10.1007/978-3-658-01681-4_16 SP - 635 EP - 678 PB - Springer Vieweg CY - Wiesbaden ER - TY - CHAP A1 - Biener, Ernst T1 - Abfallwirtschaft T2 - Wendehorst Beispiele aus der Baupraxis. - 5. Aufl. Y1 - 2015 SN - 978-3-658-01689-0 ; 978-3-410-24199-7 U6 - http://dx.doi.org/10.1007/978-3-658-01681-4_17 SP - 680 EP - 723 PB - Springer Vieweg CY - Wiesbaden ER - TY - CHAP A1 - Timme, Michael T1 - Wettbewerbsregeln (§§ 24-27) T2 - Münchener Kommentar zum europäischen und deutschen Wettbewerbsrecht (Kartellrecht) : Kartellrecht, Missbrauchs- und Fusionskontrolle / hrsg. von Joachim Bornkamm; Frank Montag; Franz Jürgen Säcker. Bd 2: Gesetz gegen Wettbewerbsbeschränkungen (GWB), §§ 1-96, 130, 131. Bd 2: Y1 - 2015 SN - 978-3-406-65462-6 SP - 267 EP - 286 PB - Beck CY - München ER - TY - CHAP A1 - Strohmeier, Andreas T1 - Siedlungswasserwirtschaft T2 - Wendehorst bautechnische Zahlentafeln / hrsg. von Ulrich Vismann. Ernst Biener ... 35. Aufl. Y1 - 2015 SN - 978-3-658-01688-3 SP - 1157 EP - 1230 PB - Springer Vieweg CY - Wiesbaden ER - TY - CHAP A1 - Biener, Ernst T1 - Abfallwirtschaft T2 - Wendehorst bautechnische Zahlentafeln / hrsg. von Ulrich Vismann. Ernst Biener ... 35. Aufl. Y1 - 2015 SN - 978-3-658-01688-3 SP - 1231 EP - 1260 PB - Springer Vieweg CY - Wiesbaden ER - TY - CHAP A1 - Rebel, Sören A1 - Hüning, Felix A1 - Scholl, Ingrid A1 - Ferrein, Alexander T1 - MQOne: Low-cost design for a rugged-terrain robot platform T2 - Intelligent robotics and applications : 8th International Conference, ICIRA 2015, Portsmouth, UK, August 24-27, 2015, Proceedings, Part II (Lecture notes in computer science : vol. 9245) N2 - Rugged terrain robot designs are important for field robotics missions. A number of commercial platforms are available, however, at an impressive price. In this paper, we describe the hardware and software component of a low-cost wheeled rugged-terrain robot. The robot is based on an electric children quad bike and is modified to be driven by wire. In terms of climbing properties, operation time and payload it can compete with some of the commercially available platforms, but at a far lower price. Y1 - 2015 SN - 978-3-319-22875-4 (print) ; 978-3-319-22876-1 (E-Book) U6 - http://dx.doi.org/10.1007/978-3-319-22876-1_19 SP - 209 EP - 221 PB - Springer CY - Cham ER - TY - CHAP A1 - Rahier, Michael A1 - Ritz, Thomas A1 - Wallenborn, Ramona T1 - Information and communication technology for integrated mobility concepts such as E-carsharing T2 - E-Mobility in Europe : trends and good practice N2 - During the past decade attitude towards sharing things has changed extremely. Not just personal data is shared (e.g. in social networks) but also mobility. Together with the increased ecological awareness of the recent years, new mobility concepts have evolved. E-carsharing has become a symbol for these changes of attitude. The management of a shared car fleet, the energy management of electric mobility and the management of various carsharing users with individual likes and dislikes are just some of the major challenges of e-carsharing. Weaving it into integrated mobility concepts, this raises complexity even further. These challenges can only be overcome by an appropriate amount of well-shaped information available at the right place and time. In order to gather, process and share the required information, fleet cars have to be equipped with modern information and communication technology (ICT) and become so-called fully connected cars. Ensuring the usability of these ICT systems is another challenge that is often neglected, even though it is usability that makes carsharing comfortable, attractive and supports users’ new attitudes. By means of an integrated and consistent concept for human-machine interaction (HMI), the usability of such systems can be raised tremendously. KW - Information and communication technology KW - Fully connected car KW - E-carsharing KW - Mobility management KW - Integrated mobility Y1 - 2015 SN - 978-3-319-13193-1 U6 - http://dx.doi.org/10.1007/978-3-319-13194-8_17 SP - 311 EP - 326 PB - Springer CY - Cham [u.a.] ER - TY - CHAP A1 - Busse, Daniel A1 - Esch, Thomas A1 - Muntaniol, Roman T1 - Thermal management in E-carsharing vehicles - preconditioning concepts of passenger compartments T2 - E-Mobility in Europe : trends and good practice N2 - The issue of thermal management in electric vehicles includes the topics of drivetrain cooling and heating, interior temperature, vehicle body conditioning and safety. In addition to the need to ensure optimal thermal operating conditions of the drivetrain components (drive motor, battery and electrical components), thermal comfort must be provided for the passengers. Thermal comfort is defined as the feeling which expresses the satisfaction of the passengers with the ambient conditions in the compartment. The influencing factors on thermal comfort are the temperature and humidity as well as the speed of the indoor air and the clothing and the activity of the passengers, in addition to the thermal radiation and the temperatures of the interior surfaces. The generation and the maintenance of free visibility (ice- and moisture-free windows) count just as important as on-demand heating and cooling of the entire vehicle. A Carsharing climate concept of the innovative ec2go vehicle stipulates and allows for only seating areas used by passengers to be thermally conditioned in a close-to-body manner. To enable this, a particular feature has been added to the preconditioning of the Carsharing electric vehicle during the electric charging phase at the parking station. KW - Carsharing KW - Thermal management KW - Thermal comfort KW - Electrical vehicle KW - Passenger compartment Y1 - 2015 SN - 978-3-319-13193-1 U6 - http://dx.doi.org/10.1007/978-3-319-13194-8_18 SP - 327 EP - 343 PB - Springer CY - Cham [u.a.] ER - TY - CHAP A1 - Kümmell, Steffen A1 - Hillgärtner, Michael T1 - Inductive charging comfortable and nonvisible charging stations for urbanised areas T2 - E-Mobility in Europe : trends and good practice N2 - For a wide acceptance of E-Mobility, a well-developed charging infrastructure is needed. Conductive charging stations, which are today’s state of the art, are of limited suitability for urbanised areas, since they cause a significant diversification in townscape. Furthermore, they might be destroyed by vandalism. Besides for those urbanistic reasons, inductive charging stations are a much more comfortable alternative, especially in urbanised areas. The usage of conductive charging stations requires more or less bulky charging cables. The handling of those standardised charging cables, especially during poor weather conditions, might cause inconvenience, such as dirty clothing etc. Wireless charging does not require visible and vandalism vulnerable charge sticks. No wired connection between charging station and vehicle is needed, which enable the placement below the surface of parking spaces or other points of interest. Inductive charging seems to be the optimal alternative for E-Mobility, as a high power transfer can be realised with a manageable technical and financial effort. For a well-accepted and working public charging infrastructure in urbanised areas it is essential that the infrastructure fits the vehicles’ needs. Hence, a well-adjusted standardisation of the charging infrastructure is essential. This is carried out by several IEC (International Electrotechnical Commission) and national standardisation committees. To ensure an optimised technical solution for future’s inductive charging infrastructures, several field tests had been carried out and are planned in near future. KW - E-mobility KW - Inductive charging KW - Charging stations KW - Urban areas Y1 - 2015 SN - 978-3-319-13193-1 U6 - http://dx.doi.org/10.1007/978-3-319-13194-8_16 SP - 297 EP - 309 PB - Springer CY - Cham [u.a.] ER -