TY - JOUR A1 - Ulmer, Jessica A1 - Braun, Sebastian A1 - Cheng, Chi-Tsun A1 - Dowey, Steve A1 - Wollert, Jörg T1 - Human-Centered Gamification Framework for Manufacturing Systems JF - Procedia CIRP N2 - While bringing new opportunities, the Industry 4.0 movement also imposes new challenges to the manufacturing industry and all its stakeholders. In this competitive environment, a skilled and engaged workforce is a key to success. Gamification can generate valuable feedbacks for improving employees’ engagement and performance. Currently, Gamification in workspaces focuses on computer-based assignments and training, while tasks that require manual labor are rarely considered. This research provides an overview of Enterprise Gamification approaches and evaluates the challenges. Based on that, a skill-based Gamification framework for manual tasks is proposed, and a case study in the Industry 4.0 model factory is shown. Y1 - 2020 U6 - http://dx.doi.org/10.1016/j.procir.2020.04.076 SN - 2212-8271 VL - 93 SP - 670 EP - 675 PB - Elsevier CY - Amsterdam ER - TY - JOUR A1 - Wollbrink, Moritz A1 - Maslo, Semir A1 - Zimmer, Daniel A1 - Abbas, Karim A1 - Arntz, Kristian A1 - Bergs, Thomas T1 - Clamping and substrate plate system for continuous additive build-up and post-processing of metal parts JF - Procedia CIRP N2 - The manufacturing share of laser powder bed fusion (L-PBF) increases in industrial application, but still many process steps are manually operated. Additionally, it is not possible to achieve tight dimensional tolerances or low surfaces roughness. Hence, a process chain has to be set up to combine additive manufacturing (AM) with further machining technologies. To achieve a continuous workpiece flow as basis for further industrialization of L-PBF, the paper presents a novel substrate system and its application on L-PBF machines and post-processing. The substrate system consists of a zero-point clamping system and a matrix-like interface of contact pins to be substantially connected to the workpiece within the L-PBF process. Y1 - 2020 U6 - http://dx.doi.org/10.1016/j.procir.2020.04.015 SN - 2212-8271 VL - 93 SP - 108 EP - 113 PB - Elsevier CY - Amsterdam ER - TY - JOUR A1 - Franko, Josef A1 - Du, Shengzhi A1 - Kallweit, Stephan A1 - Duelberg, Enno Sebastian A1 - Engemann, Heiko T1 - Design of a Multi-Robot System for Wind Turbine Maintenance JF - Energies N2 - The maintenance of wind turbines is of growing importance considering the transition to renewable energy. This paper presents a multi-robot-approach for automated wind turbine maintenance including a novel climbing robot. Currently, wind turbine maintenance remains a manual task, which is monotonous, dangerous, and also physically demanding due to the large scale of wind turbines. Technical climbers are required to work at significant heights, even in bad weather conditions. Furthermore, a skilled labor force with sufficient knowledge in repairing fiber composite material is rare. Autonomous mobile systems enable the digitization of the maintenance process. They can be designed for weather-independent operations. This work contributes to the development and experimental validation of a maintenance system consisting of multiple robotic platforms for a variety of tasks, such as wind turbine tower and rotor blade service. In this work, multicopters with vision and LiDAR sensors for global inspection are used to guide slower climbing robots. Light-weight magnetic climbers with surface contact were used to analyze structure parts with non-destructive inspection methods and to locally repair smaller defects. Localization was enabled by adapting odometry for conical-shaped surfaces considering additional navigation sensors. Magnets were suitable for steel towers to clamp onto the surface. A friction-based climbing ring robot (SMART— Scanning, Monitoring, Analyzing, Repair and Transportation) completed the set-up for higher payload. The maintenance period could be extended by using weather-proofed maintenance robots. The multi-robot-system was running the Robot Operating System (ROS). Additionally, first steps towards machine learning would enable maintenance staff to use pattern classification for fault diagnosis in order to operate safely from the ground in the future. Y1 - 2020 U6 - http://dx.doi.org/10.3390/en13102552 SN - 1996-1073 VL - 13 IS - 10 SP - Article 2552 PB - MDPI CY - Basel ER - TY - JOUR A1 - Raffeis, Iris A1 - Adjei-Kyeremeh, Frank A1 - Vroomen, Uwe A1 - Westhoff, Elmar A1 - Bremen, Sebastian A1 - Hohoi, Alexandru A1 - Bührig-Polaczek, Andreas T1 - Qualification of a Ni-Cu alloy for the laser powder bed fusion process (LPBF): Its microstructure and mechanical properties JF - Applied Sciences N2 - As researchers continue to seek the expansion of the material base for additive manufacturing, there is a need to focus attention on the Ni–Cu group of alloys which conventionally has wide industrial applications. In this work, the G-NiCu30Nb casting alloy, a variant of the Monel family of alloys with Nb and high Si content is, for the first time, processed via the laser powder bed fusion process (LPBF). Being novel to the LPBF processes, optimum LPBF parameters were determined, and hardness and tensile tests were performed in as-built conditions and after heat treatment at 1000 °C. Microstructures of the as-cast and the as-built condition were compared. Highly dense samples (99.8% density) were achieved after varying hatch distance (80 µm and 140 µm) with scanning speed (550 mm/s–1500 mm/s). There was no significant difference in microhardness between varied hatch distance print sets. Microhardness of the as-built condition (247 HV0.2) exceeded the as-cast microhardness (179 HV0.2.). Tensile specimens built in vertical (V) and horizontal (H) orientations revealed degrees of anisotropy and were superior to conventionally reported figures. Post heat treatment increased ductility from 20% to 31% (V), as well as from 16% to 25% (H), while ultimate tensile strength (UTS) and yield strength (YS) were considerably reduced. Y1 - 2020 U6 - http://dx.doi.org/10.3390/app10103401 SN - 2076-3417 N1 - Special Issue Materials Development by Additive Manufacturing Techniques VL - 10 IS - Art. 3401 SP - 1 EP - 15 PB - MDPI CY - Basel ER - TY - JOUR A1 - Cosma, Cosmin A1 - Kessler, Julia A1 - Gebhardt, Andreas A1 - Campbell, Ian A1 - Balc, Nicolae T1 - Improving the Mechanical Strength of Dental Applications and Lattice Structures SLM Processed JF - Materials N2 - To manufacture custom medical parts or scaffolds with reduced defects and high mechanical characteristics, new research on optimizing the selective laser melting (SLM) parameters are needed. In this work, a biocompatible powder, 316L stainless steel, is characterized to understand the particle size, distribution, shape and flowability. Examination revealed that the 316L particles are smooth, nearly spherical, their mean diameter is 39.09 μm and just 10% of them hold a diameter less than 21.18 μm. SLM parameters under consideration include laser power up to 200 W, 250–1500 mm/s scanning speed, 80 μm hatch spacing, 35 μm layer thickness and a preheated platform. The effect of these on processability is evaluated. More than 100 samples are SLM-manufactured with different process parameters. The tensile results show that is possible to raise the ultimate tensile strength up to 840 MPa, adapting the SLM parameters for a stable processability, avoiding the technological defects caused by residual stress. Correlating with other recent studies on SLM technology, the tensile strength is 20% improved. To validate the SLM parameters and conditions established, complex bioengineering applications such as dental bridges and macro-porous grafts are SLM-processed, demonstrating the potential to manufacture medical products with increased mechanical resistance made of 316L. Y1 - 2020 U6 - http://dx.doi.org/10.3390/ma13040905 SN - 1996-1944 VL - 13 IS - 4 SP - 1 EP - 18 PB - MDPI CY - Basel ER - TY - JOUR A1 - Engemann, Heiko A1 - Du, Shengzhi A1 - Kallweit, Stephan A1 - Cönen, Patrick A1 - Dawar, Harshal T1 - OMNIVIL - an autonomous mobile manipulator for flexible production JF - Sensors Y1 - 2020 SN - 1424-8220 U6 - http://dx.doi.org/10.3390/s20247249 N1 - Special issue: Sensor Networks Applications in Robotics and Mobile Systems VL - 20 IS - 24, art. no. 7249 SP - 1 EP - 30 PB - MDPI CY - Basel ER - TY - JOUR A1 - Bucur, Alexandru A1 - Lazarescu, Lucian A1 - Pop, Grigore Marian A1 - Achimas, Gheorghe A1 - Gebhardt, Andreas T1 - Tribological performance of biodegradable lubricants under different surface roughness of tools JF - Academic Journal of Manufacturing Engineering Y1 - 2019 SN - 1583-7904 VL - 17 IS - 1 SP - 172 EP - 178 ER - TY - JOUR A1 - Panc, Nicolae A1 - Contiu, Glad A1 - Bocanet, Vlad A1 - Thurn, Laura A1 - Sabau, Emilia T1 - The influence of cutting technology on surface wear hardness JF - Academic Journal of Manufacturing Engineering Y1 - 2019 SN - 1583-7904 VL - 17 IS - 3 SP - 205 EP - 210 ER - TY - JOUR A1 - Kunkel, Maximilian Hugo A1 - Gebhardt, Andreas A1 - Mpofu, Khumbulani A1 - Kallweit, Stephan T1 - Quality assurance in metal powder bed fusion via deep-learning-based image classification JF - Rapid Prototyping Journal Y1 - 2019 U6 - http://dx.doi.org/10.1108/RPJ-03-2019-0066 SN - 1355-2546 VL - 26 IS - 2 SP - 259 EP - 266 ER - TY - JOUR A1 - Schwarz, Alexander A1 - Gebhardt, Andreas A1 - Schleser, Markus A1 - Popoola, Patricia T1 - New Welding Joint Geometries Manufactured by Powder Bed Fusion from 316L JF - Materials Performance and Characterization 8 Y1 - 2019 U6 - http://dx.doi.org/10.1520/MPC20180096 SN - 2379-1365 IS - in press ER - TY - JOUR A1 - Michaux, F. A1 - Mattern, P. A1 - Kallweit, Stephan T1 - RoboPIV: how robotics enable PIV on a large industrial scale JF - Measurement Science and Technology N2 - This work demonstrates how the interaction between particle image velocimetry (PIV) and robotics can massively increase measurement efficiency. The interdisciplinary approach is shown using the complex example of an automated, large scale, industrial environment: a typical automotive wind tunnel application. Both the high degree of flexibility in choosing the measurement region and the complete automation of stereo PIV measurements are presented. The setup consists of a combination of three robots, individually used as a 6D traversing unit for the laser illumination system as well as for each of the two cameras. Synchronised movements in the same reference frame are realised through a master-slave setup with a single interface to the user. By integrating the interface into the standard wind tunnel management system, a single measurement plane or a predefined sequence of several planes can be requested through a single trigger event, providing the resulting vector fields within minutes. In this paper, a brief overview on the demands of large scale industrial PIV and the existing solutions is given. Afterwards, the concept of RoboPIV is introduced as a new approach. In a first step, the usability of a selection of commercially available robot arms is analysed. The challenges of pose uncertainty and importance of absolute accuracy are demonstrated through comparative measurements, explaining the individual pros and cons of the analysed systems. Subsequently, the advantage of integrating RoboPIV directly into the existing wind tunnel management system is shown on basis of a typical measurement sequence. In a final step, a practical measurement procedure, including post-processing, is given by using real data and results. Ultimately, the benefits of high automation are demonstrated, leading to a drastic reduction in necessary measurement time compared to non-automated systems, thus massively increasing the efficiency of PIV measurements. Y1 - 2018 U6 - http://dx.doi.org/10.1088/1361-6501/aab5c1 SN - 1361-6501 N1 - Special Section on the 12th International Symposium on Particle Image Velocimetry (PIV 2017) VL - 29 IS - 7 SP - 074009 PB - IOP CY - Bristol ER - TY - JOUR A1 - Kunkel, Maximilian Hugo A1 - Gebhardt, Andreas A1 - Mpofu, Khumbaulani A1 - Kallweit, Stephan T1 - Statistical assessment of mechanical properties of selective laser melted specimens of stainless steel JF - The International Journal of Advanced Manufacturing Technology N2 - The rail business is challenged by long product life cycles and a broad spectrum of assembly groups and single parts. When spare part obsolescence occurs, quick solutions are needed. A reproduction of obsolete parts is often connected to long waiting times and minimum lot quantities that need to be purchased and stored. Spare part storage is therefore challenged by growing stocks, bound capital and issues of part ageing. A possible solution could be a virtual storage of spare parts which will be 3D printed through additive manufacturing technologies in case of sudden demand. As mechanical properties of additive manufactured parts are neither guaranteed by machine manufacturers nor by service providers, the utilization of this relatively young technology is impeded and research is required to address these issues. This paper presents an examination of mechanical properties of specimens manufactured from stainless steel through the selective laser melting (SLM) process. The specimens were produced in multiple batches. This paper interrogates the question if the test results follow a normal distribution pattern and if mechanical property predictions can be made. The results will be put opposite existing threshold values provided as the industrial standard. Furthermore, probability predictions will be made in order to examine the potential of the SLM process to maintain state-of-the-art mechanical property requirements. Y1 - 2018 U6 - http://dx.doi.org/10.1007/s00170-018-2040-8 SN - 0268-3768 VL - 98 IS - 5-8 SP - 1409 EP - 1431 PB - Springer CY - London ER - TY - JOUR A1 - Franzen, Julius A1 - Pinders, Erik A1 - Pfaff, Raphael A1 - Enning, Manfred T1 - RailCrowd’s virtual fleets: Make most of your asset data JF - Deine Bahn N2 - For smaller railway operators or those with a diverse fleet, it can be difficult to collect sufficient data to improve maintenance programs. At the same time, new rules such as entity in charge of maintenance – ECM – regulations impose an additional workload by requiring a dedicated maintenance management system and specific reports. The RailCrowd platform sets out to facilitate compliance with ECM and similar regulations while at the same time pooling anonymised fleet data across operators to form virtual fleets, providing greater data insights. Y1 - 2018 SN - 0948-7263 IS - 9 SP - 11 EP - 13 PB - Bahn-Fachverlag CY - Berlin ER - TY - JOUR A1 - Kilic, S. A. A1 - Raatschen, Hans-Jürgen A1 - Körfgen, B. A1 - Apaydin, N. M. A1 - Astaneh-Asl, A. T1 - FE Model of the Fatih Sultan Mehmet Suspension Bridge Using Thin Shell Finite Elements JF - Arabian Journal for Science and Engineering N2 - This paper presents the results of an eigenvalue analysis of the Fatih Sultan Mehmet Bridge. A high-resolution finite element model was created directly from the available design documents. All physical properties of the structural components were included in detail, so no calibration to the measured data was necessary. The deck and towers were modeled with shell elements. A nonlinear static analysis was performed before the eigenvalue calculation. The calculated natural frequencies and corresponding mode shapes showed good agreement with the available measured ambient vibration data. The calculation of the effective modal mass showed that nine modes had single contributions higher than 5 % of the total mass. They were in a frequency range up to 1.2 Hz. The comparison of the results for the torsional modes especially demonstrated the advantage of using thin shell finite elements over the beam modeling approach. KW - Suspension bridge KW - 3D nonlinear finite element model KW - Thin shell finite elements KW - Natural frequency KW - Effective modal mass Y1 - 2017 U6 - http://dx.doi.org/10.1007/s13369-016-2316-y SN - 2191-4281 VL - 42 IS - 3 SP - 1103 EP - 1116 PB - Springer Nature ER - TY - JOUR A1 - Koster, Arie A1 - Scheidweiler, Robert A1 - Tieves, Martin T1 - A flow based pruning scheme for enumerative equitable coloring algorithms JF - A flow based pruning scheme for enumerative equitable coloring algorithms N2 - An equitable graph coloring is a proper vertex coloring of a graph G where the sizes of the color classes differ by at most one. The equitable chromatic number is the smallest number k such that G admits such equitable k-coloring. We focus on enumerative algorithms for the computation of the equitable coloring number and propose a general scheme to derive pruning rules for them: We show how the extendability of a partial coloring into an equitable coloring can be modeled via network flows. Thus, we obtain pruning rules which can be checked via flow algorithms. Computational experiments show that the search tree of enumerative algorithms can be significantly reduced in size by these rules and, in most instances, such naive approach even yields a faster algorithm. Moreover, the stability, i.e., the number of solved instances within a given time limit, is greatly improved. Since the execution of flow algorithms at each node of a search tree is time consuming, we derive arithmetic pruning rules (generalized Hall-conditions) from the network model. Adding these rules to an enumerative algorithm yields an even larger runtime improvement. Y1 - 2016 U6 - http://dx.doi.org/10.48550/arXiv.1607.08754 N1 - Lehrstuhl II für Mathematik, RWTH Aachen University SP - 1 EP - 30 ER - TY - JOUR A1 - Beckenbach, Isabel A1 - Scheidweiler, Robert T1 - Perfect ƒ-Matchings and ƒ-Factors in Hypergraphs - A Combinatorial Approach JF - Discrete Mathematics N2 - We prove characterizations of the existence of perfect ƒ-matchings in uniform mengerian and perfect hypergraphs. Moreover, we investigate the ƒ-factor problem in balanced hypergraphs. For uniform balanced hypergraphs we prove two existence theorems with purely combinatorial arguments, whereas for non-uniform balanced hypergraphs we show that the ƒ-factor problem is NP-hard. Y1 - 2016 U6 - http://dx.doi.org/10.1016/j.disc.2017.05.005 SN - 2192-7782 N1 - Als Volltext auch bei ZIB (Zuse Institute Berlin) VL - 240 IS - 10 SP - 2499 EP - 2506 PB - Elsevier CY - Amsterdam ER - TY - JOUR A1 - Scheidweiler, Robert A1 - Triesch, Eberhard T1 - A note on the duality between matchings and vertex covers in balanced hypergraphs JF - Journal of Combinatorial Optimization N2 - We present a new Min-Max theorem for an optimization problem closely connected to matchings and vertex covers in balanced hypergraphs. The result generalizes Kőnig’s Theorem (Berge and Las Vergnas in Ann N Y Acad Sci 175:32–40, 1970; Fulkerson et al. in Math Progr Study 1:120–132, 1974) and Hall’s Theorem (Conforti et al. in Combinatorica 16:325–329, 1996) for balanced hypergraphs. KW - Hall’s Theorem KW - Koenig’s Theorem KW - Duality KW - Balanced hypergraph KW - Hypergraph KW - Vertex cover KW - Matching Y1 - 2016 U6 - http://dx.doi.org/10.1007/s10878-015-9887-5 SN - 1573-2886 N1 - Lehrstuhl II für Mathematik RWTH Aachen VL - 32 IS - 2 SP - 639 EP - 644 PB - Springer CY - Berlin ER - TY - JOUR A1 - Rieper, Harald A1 - Gebhardt, Andreas A1 - Stucker, Brent T1 - Selective Laser Melting of the Eutectic Silver-Copper Alloy Ag 28 wt % Cu JF - RTejournal - Forum für Rapid Technologie N2 - The aim of this work was to perform a detailed investigation of the use of Selective Laser Melting (SLM) technology to process eutectic silver-copper alloy Ag 28 wt. % Cu (also called AgCu28). The processing occurred with a Realizer SLM 50 desktop machine. The powder analysis (SEM-topography, EDX, particle distribution) was reported as well as the absorption rates for the near-infrared (NIR) spectrum. Microscope imaging showed the surface topography of the manufactured parts. Furthermore, microsections were conducted for the analysis of porosity. The Design of Experiments approach used the response surface method in order to model the statistical relationship between laser power, spot distance and pulse time. KW - SLM KW - Response Surface Method KW - Porositat KW - Eutectic Silver Copper alloy KW - Additive Manufacturing Y1 - 2016 U6 - http://nbn-resolving.de/urn/resolver.pl?nbn:de:0009-2-44141 SN - 1614-0923 VL - 13 ER - TY - JOUR A1 - Fateri, Miranda A1 - Gebhardt, Andreas T1 - Selective Laser Melting of Soda-Lime Glass Powder JF - International Journal of Applied Ceramic Technology Y1 - 2015 U6 - http://dx.doi.org/10.1111/ijac.12338 SN - 1744-7402 VL - 12 IS - 1 SP - 53 EP - 61 PB - Wiley-Blackwell CY - Oxford ER - TY - JOUR A1 - Fateri, Miranda A1 - Gebhardt, Andreas T1 - Process Parameters Development of Selective Laser Melting of Lunar Regolith for On-Site Manufacturing Applications JF - International Journal of Applied Ceramic Technology Y1 - 2015 SN - 1744-7402 U6 - http://dx.doi.org/10.1111/ijac.12326 VL - 12 IS - 1 SP - 46 EP - 52 PB - Wiley-Blackwell CY - Oxford ER - TY - JOUR A1 - Fateri, Miranda A1 - Gebhardt, Andreas T1 - Additive manufactured mechanical disentanglement lock JF - RTejournal - Forum für Rapid Technologie Y1 - 2015 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:0009-2-42147 SN - 1614-0923 VL - 12 PB - Fachhochschule Aachen CY - Aachen ER - TY - JOUR A1 - Kessler, Julia A1 - Balc, Nicolae A1 - Gebhardt, Andreas A1 - Abbas, Karim T1 - Basic Research on Lattice Structures Focused on the Tensile Strength JF - Applied Mechanics and Materials Y1 - 2015 U6 - http://dx.doi.org/10.4028/www.scientific.net/AMM.808.193 SN - 1662-7482 N1 - MTeM ; October 14-16, 2015, Cluj-Napoca, Romania VL - Vol. 808 SP - 193 EP - 198 PB - Trans Tech Publications CY - Bäch ER - TY - JOUR A1 - Fateri, Miranda A1 - Gebhardt, Andreas A1 - Thümmler, Stefan A1 - Thurn, Laura T1 - Experimental investigation on selective laser melting of glass JF - Physics procedia : 8th International Conference on Laser Assisted Net Shape Engineering LANE 2014 Y1 - 2014 U6 - http://dx.doi.org/10.1016/j.phpro.2014.08.118 SN - 1875-3892 (E-Journal); 1875-3884 (Print) VL - 56 (2014) SP - 357 EP - 364 PB - Elsevier CY - Amsterdam ER - TY - JOUR A1 - Haag, S. A1 - Zontar, D. A1 - Schleupen, Josef A1 - Müller, T. A1 - Brecher, C. T1 - Chain of refined perception in self-optimizing assembly of micro-optical systems JF - Journal of sensors and sensor systems N2 - Today, the assembly of laser systems requires a large share of manual operations due to its complexity regarding the optimal alignment of optics. Although the feasibility of automated alignment of laser optics has been shown in research labs, the development effort for the automation of assembly does not meet economic requirements – especially for low-volume laser production. This paper presents a model-based and sensor-integrated assembly execution approach for flexible assembly cells consisting of a macro-positioner covering a large workspace and a compact micromanipulator with camera attached to the positioner. In order to make full use of available models from computer-aided design (CAD) and optical simulation, sensor systems at different levels of accuracy are used for matching perceived information with model data. This approach is named "chain of refined perception", and it allows for automated planning of complex assembly tasks along all major phases of assembly such as collision-free path planning, part feeding, and active and passive alignment. The focus of the paper is put on the in-process image-based metrology and information extraction used for identifying and calibrating local coordinate systems as well as the exploitation of that information for a part feeding process for micro-optics. Results will be presented regarding the processes of automated calibration of the robot camera as well as the local coordinate systems of part feeding area and robot base. Y1 - 2014 U6 - http://dx.doi.org/10.5194/jsss-3-87-2014 SN - 2194-878X VL - 3 IS - 1 SP - 87 EP - 95 PB - Copernicus Publ. CY - Göttingen ER - TY - JOUR A1 - Gebhardt, Andreas A1 - Fateri, Miranda T1 - 3D printing and its applications JF - RTejournal - Forum für Rapid Technologie N2 - Eine zunehmende Anzahl von Artikeln in Publikumszeitschriften und Journalen rückt die direkte Herstellung von Bauteilen und Figuren immer mehr in das Bewusstsein einer breiten Öffentlichkeit. Leider ergibt sich nur selten ein einigermaßen vollständiges Bild davon, wie und in welchen Lebensbereichen diese Techniken unseren Alltag verändern werden. Das liegt auch daran, dass die meisten Artikel sehr technisch geprägt sind und sich nur punktuell auf Beispiele stützen. Dieser Beitrag geht von den Bedürfnissen der Menschen aus, wie sie z.B. in der Maslow’schen Bedürfnispyramide strukturiert dargestellt sind und unterstreicht dadurch, dass 3D Printing (oder Additive Manufacturing resp. Rapid Prototyping) bereits alle Lebensbereiche erfasst hat und im Begriff ist, viele davon zu revolutionieren. N2 - An increasing amount of popular articles focus on making models and sculptures by 3D Printing thus making more and more even private users aware of this technology. Unfortunately they mostly draw an incomplete picture of how our daily life will be influenced by this new technology. Often this is caused by a very technical point of view based on not very representative examples. This article focuses on the peoples needs as they have been structured by the so-called Maslow pyramid. Doing so, it underlines that 3D Printing (called Additive Manufacturing or Rapid Prototyping as well) already touches all aspects of life and is about to revolutionize most of them. Y1 - 2013 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:0009-2-35626 SN - 1614-0923 VL - 10 IS - 1 PB - Fachhochschule Aachen CY - Aachen ER - TY - JOUR A1 - Ramazani, Ali A1 - Li, Yang A1 - Mukherjee, Krishnendu A1 - Prahl, Ulrich A1 - Bleck, Wolfgang A1 - Abdurakhmanov, Aydemir A1 - Schleser, Markus A1 - Reisgen, Uwe T1 - Microstructure evolution simulation in hot rolled DP600 steel during gas metal arc welding JF - Computational materials science Y1 - 2013 SN - 1879-0801 (E-Book); 0927-0256 (Print) VL - Vol. 68 SP - 107 EP - 116 PB - Elsevier CY - Amsterdam ER - TY - JOUR A1 - Fateri, Miranda A1 - Hötter, Jan-Steffen A1 - Gebhardt, Andreas T1 - Experimental and Theoretical Investigation of Buckling Deformation of Fabricated Objects by Selective Laser Melting JF - Physics Procedia N2 - Although Selective Laser Melting (SLM) process is an innovative manufacturing method, there are challenges such as inferior mechanical properties of fabricated objects. Regarding this, buckling deformation which is caused by thermal stress is one of the undesired mechanical properties which must be alleviated. As buckling deformation is more observable in hard to process materials, silver is selected to be studied theoretically and experimentally for this paper. Different scanning strategies are utilized and a Finite Element Method (FEM) is applied to calculate the temperature gradient in order to determine its effect on the buckling deformation of the objects from experiments. Y1 - 2012 U6 - http://dx.doi.org/10.1016/j.phpro.2012.10.062 SN - 1875-3892 N1 - Part of special issue "Laser Assisted Net shape Engineering 7 (LANE 2012)" VL - 39 SP - 464 EP - 470 PB - Elsevier CY - Amsterdam ER - TY - JOUR A1 - Reisgen, Uwe A1 - Schleser, Markus A1 - Mokrov, Oleg A1 - Ahmed, Essam T1 - Statistical modeling of laser welding of DP/TRIP steel sheets JF - Optics and laser technology N2 - In this research work, a statistical analysis of the CO2 laser beam welding of dual phase (DP600)/transformation induced plasticity (TRIP700) steel sheets was done using response surface methodology. The analysis considered the effect of laser power (2–2.2 kW), welding speed (40–50 mm/s) and focus position (−1 to 0 mm) on the heat input, the weld bead geometry, uniaxial tensile strength, formability limited dome height and welding operation cost. The experimental design was based on Box–Behnken design using linear and quadratic polynomial equations for predicting the mathematical models. The results indicate that the proposed models predict the responses adequately within the limits of welding parameters being used and the welding speed is the most significant parameter during the welding process. Y1 - 2012 U6 - http://dx.doi.org/10.1016/j.optlastec.2011.05.025 SN - 1879-2545 (E-Journal); 0030-3992 (Print); 0308-4280 (Print) VL - 44 IS - 1 SP - 92 EP - 101 PB - Elsevier CY - Amsterdam ER - TY - JOUR A1 - Reisgen, Uwe A1 - Schleser, Markus A1 - Mokrov, Oleg A1 - Ahmed, Essam T1 - Optimization of laser welding of DP/TRIP steel sheets using statistical approach JF - Optics and laser technology N2 - Generally, the quality of a weld joint is directly influenced by the welding input parameter settings. Selection of proper process parameters is important to obtain the desired weld bead profile and quality. In this research work, numerical and graphical optimization techniques of the CO2 laser beam welding of dual phase (DP600)/transformation induced plasticity (TRIP700) steel sheets were carried out using response surface methodology (RSM) based on Box–Behnken design. The procedure was established to improve the weld quality, increase the productivity and minimize the total operation cost by considering the welding parameters range of laser power (2–2.2 kW), welding speed (40–50 mm/s) and focus position (−1 to 0 mm). It was found that, RSM can be considered as a powerful tool in experimental welding optimization, even when the experimenter does not have a model for the process. Strong, efficient and low cost weld joints could be achieved using the optimum welding conditions. Y1 - 2012 U6 - http://dx.doi.org/10.1016/j.optlastec.2011.06.028 SN - 1879-2545 (E-Journal); 0030-3992 (Print); 0308-4280 (Print) VL - 44 IS - 1 SP - 255 EP - 262 PB - Elsevier CY - Amsterdam ER - TY - JOUR A1 - Reisgen, Uwe A1 - Olschok, Simon A1 - Jakobs, Stefan A1 - Schleser, Markus A1 - Mokrov, Oleg A1 - Rossiter, Eduardo T1 - Laser beam submerged arc hybrid welding JF - Physics procedia N2 - The laser beam-submerged arc hybrid welding method originates from the knowledge that, with increasing penetration depth, the laser beam process has a tendency to pore formation in the lower weld regions. The coupling with the energy-efficient submerged-arc process improves degassing and reduces the tendency to pore formation. The high deposition rate of the SA process in combination with the laser beam process offers, providing the appropriate choice of weld preparation, the possibility of welding plates with a thickness larger than 20° mm in a single pass, and also of welding thicker plates with the double-sided single pass technique. Y1 - 2012 U6 - http://dx.doi.org/10.1016/j.phpro.2012.10.016 SN - 1875-3892 N1 - Part of special issue "Laser assisted net shape engineering 7 (LANE 2012)" VL - 39 SP - 75 EP - 83 PB - Elsevier CY - Amsterdam ER - TY - JOUR A1 - Reisgen, Uwe A1 - Schleser, Markus A1 - Abdurakhmanov, Aydemir A1 - Gumenyuk, Andrey T1 - Measuring of plasma properties induced by non-vacuum electron beam welding JF - Physics of plasma N2 - Electron beam plasma measurement was realised by means of DIABEAM system invented by ISF RWTH Aachen. The Langmuir probe method is used for measurement. The relative simplicity of the method and the possibility of dispersion of high power on the probe allow its application for the investigation of high-power electron beams. The key element of the method is a rotating thin tungsten wire, which intersects the beam transversely on its axis and collects part of the current by itself. The signals, which are registered in the DIABEAM as a voltage, were taken in the form of amplitude. The conversion of the probe current into the distribution along the beam radius was realised using the Abel’s method. A voltage-current characteristic was built for the beam current. The local electron density as well as the electron temperature, the floating potential and the plasma potential were measured and calculated by means of this characteristic. Y1 - 2012 U6 - http://dx.doi.org/10.1063/1.3675874 SN - 1089-7674 (E-Journal); 1070-664X (Print) VL - 19 IS - 1 SP - 1 EP - 7 PB - AIP Publishing CY - Melville, NY ER - TY - JOUR A1 - Reisgen, Uwe A1 - Schleser, Markus A1 - Mokrov, Oleg A1 - Zabirov, Alexander A1 - Füssel, Uwe A1 - Schnick, Michael A1 - Hertel, Martin A1 - Jaeckel, Sebastian T1 - Modelling and visualisation of the GMA process JF - Welding and Cutting Y1 - 2012 SN - 1612-3433 VL - 11 IS - 4 SP - 242 EP - 249 PB - DVS Verlag CY - Düsseldorf ER - TY - JOUR A1 - Hötter, Jan-Steffen A1 - Fateri, Miranda A1 - Gebhardt, Andreas T1 - Selective laser melting of metals: desktop machines open up new chances even for small companies JF - Advanced materials research N2 - Additive manufacturing (AM) of metal parts by using Selective Laser Melting (SLM) has become a powerful tool mostly in the area of automotive, aerospace engineering and others. Especially in the field of dentistry, jewelry and related branches that require individualized or even one-of-a-kind products, the direct digital manufacturing process opens up new ways of design and manufacturing. In these fields, mostly small and medium sized businesses (SME) are operating which do not have sufficient human and economic resources to invest in this technology. But to stay competitive, the application of AM can be regarded as a necessity. In this situation a new desktop machine (Realizer SLM 50) was introduced that cost about 1/3 of a shop floor SLM machine and promises small quality parts. To find out whether the machine really is an alternative for SMEs the University of Applied Science, Aachen, Germany, designed, build and optimized typical parts from the dentistry and the jewelry branches using CoCr and silver material, the latter being new with this application. The paper describes the SLM procedure and how to find and optimize the most important parameters. The test is accompanied by digital simulation in order to verify the build parameters and to plan future builds. The procedure is shown as well as the resulting parts made from CoCr and silver material. Y1 - 2012 U6 - http://dx.doi.org/10.4028/www.scientific.net/AMR.622-623.461 SN - 1662-8985 (E-Journal); 1022-6680 (Print) VL - 622-623 SP - 461 EP - 465 PB - Trans Tech Publ. CY - Baech ER - TY - JOUR A1 - Leidinger, Rafael A1 - Noisten, Thomas A1 - Wollert, Jörg T1 - Realtime automation networks in moVing industrial environments JF - Journal of systemics, cybernetics and informatics N2 - The radio-based wireless data communication has made the realization of new technical solutions possible in many fields of the automation technology (AT). For about ten years, a constant disproportionate growth of wireless technologies can be observed in the automation technology. However, it shows that especially for the AT, conventional technologies of office automation are unsuitable and/or not manageable. The employment of mobile services in the industrial automation technology has the potential of significant cost and time savings. This leads to an increased productivity in various fields of the AT, for example in the factory and process automation or in production logistics. In this paper technologies and solutions for an automation-suited supply of mobile wireless services will be introduced under the criteria of real time suitability, IT-security and service orientation. Emphasis will be put on the investigation and development of wireless convergence layers for different radio technologies, on the central provision of support services for an easy-to-use, central, backup enabled management of combined wired / wireless networks and on the study on integrability in a Profinet real-time Ethernet network. KW - PROFINET KW - Distributed Control Systems, KW - Industrial Automation Technology, KW - 802.15.4 KW - Bluetooth KW - Wireless Networks Y1 - 2012 SN - 1690-4532 VL - Vol. 10 IS - Iss. 2 SP - 52 EP - 56 PB - IIIC CY - Orlando ER - TY - JOUR A1 - Mukherjee, Krishnendu A1 - Ramazani, Ali A1 - Yang, Li A1 - Prahl, Ulrich A1 - Bleck, Wolfgang A1 - Reisgen, Uwe A1 - Schleser, Markus A1 - Abdurakhmanov, Aydemir T1 - Characterization of gas metal arc welded hot rolled DP600 steel JF - Steel research international Y1 - 2011 SN - 1869-344X (E-Book); 1611-3683 (Print) VL - Vol. 82 IS - Iss. 12 SP - 1408 EP - 1416 PB - Wiley CY - Weinheim ER - TY - JOUR A1 - Glowania, Michael A1 - Gries, Thomas A1 - Schoene, Jens A1 - Schleser, Markus A1 - Reisgen, Uwe T1 - Innovative coating technology for textile reinforcements of concrete applications JF - 13th International Congress on Polymers in Concrete : 10 - 12 February 2010, Funchal, Madeira, Portugal.(Key engineering materials. Vol. 466) Y1 - 2011 SN - 978-3-03785-008-4 SN - 1013-9826 (E-Journal) ; 0252-1059 (Print) SP - 167 EP - 173 PB - Trans Tech Publications CY - Bäch ER - TY - JOUR A1 - Reisgen, Uwe A1 - Schleser, Markus A1 - Mokrov, Oleg A1 - Ahmed, Essam T1 - Numerical and experimental investigation of tensile behavior of laser beam welded TRIP700 steel JF - ISIJ international Y1 - 2011 SN - 1347-5460 (E-Journal); 0915-1559 (Print) VL - Vol. 51 IS - No. 3 SP - 429 EP - 434 PB - ISIJ CY - Tōkyō ER - TY - JOUR A1 - Roesner, Andreas A1 - Scheik, Sven A1 - Olowinsky, Alexander A1 - Gillner, Arnold A1 - Propawe, Reinhart A1 - Schleser, Markus A1 - Reisgen, Uwe T1 - Innovative approach of joining hybrid components JF - Journal of laser applications Y1 - 2011 SN - 1042-346X VL - Vol. 23 IS - Iss. 3 SP - 32007 PB - Laser Institute of America CY - Orlando, Fla. ER - TY - JOUR A1 - Roesner, Andreas A1 - Scheik, Sven A1 - Olowinsky, Alexander A1 - Gillner, Arnold A1 - Reisgen, Uwe A1 - Schleser, Markus T1 - Laser assisted joining of plastic metal hybrids JF - Lasers in manufacturing 2011 : proceedings of the sixth International WLT Conference on Lasers in Manufacturing, Munich, May 23 - 26 2011. (Physics procedia ; Vol. 12 (2011), Part B) Y1 - 2011 SN - 1875-3892 (E-Journal); 1875-3884 (Print) SP - 370 EP - 377 PB - Elsevier CY - Amsterdam ER - TY - JOUR A1 - Reisgen, Uwe A1 - Schleser, Markus A1 - Mokrov, Oleg A1 - Zabirov, Alexander T1 - Virtual welding equipment for simulation of GMAW processes with integration of power source regulation JF - Frontiers of materials science Y1 - 2011 SN - 2095-0268 (E-Journal); 2095-025X (Print) VL - Vol. 5 IS - Iss. 2 SP - 79 EP - 89 PB - Springer CY - Berlin ER - TY - JOUR A1 - Gebhardt, Andreas A1 - Schmidt, Frank-Michael A1 - Hötter, Jan-Steffen A1 - Sokalla, Wolfgang A1 - Sokalla, Patrick T1 - Additive Manufacturing by selective laser melting the realizer desktop machine and its application for the dental industry JF - Physics Procedia Y1 - 2010 SN - 1875-3892 N1 - Laser Assisted Net Shape Engineering 6, Proceedings of the LANE 2010, Part 2 VL - 5 IS - 2 SP - 543 EP - 549 ER - TY - JOUR A1 - Reisgen, Uwe A1 - Schleser, Markus A1 - Mokrov, Oleg A1 - Ahmed, Essam T1 - Uni- and bi-axial deformation behavior of laser welded advanced high strength steel sheets JF - Journal of materials processing technology N2 - Bead-on-plate butt joints of 2.5 mm hot rolled DP600/DP600 and 1.2 mm cold rolled TRIP700/TRIP700 steel sheets were performed using 6 kW CO2 laser beam welding. The welding speed ranged from 1.5 to 3.0 and from 2.1 to 3.9 m/min in DP/DP and TRIP/TRIP steel weldments respectively. A top surface helium gas was used as a shielding gas at a flow rate of 20 l/min. Metallographic examinations and transverse tensile testing (DIN EN 895: 1995) were carried out to characterize the weldments. The formability of base metals and weldments were investigated by standard Erichsen test (DIN EN ISO 20482). It was found that the uniaxial plastic behavior of both DP600 and TRIP700 base metals was in agreement with Swift and modified Mecking–Kocks models respectively. In a perpendicular tensile test to the weld line, all specimens were fractured at the base metal however the strengths were somewhat higher than those of base metal. There was a significant reduction in formability caused by welding of both DP/DP and TRIP/TRIP steel weldments and the formability has been improved with the increase of the welding speed. Y1 - 2010 U6 - http://dx.doi.org/http10.1016/j.jmatprotec.2010.08.003 SN - 0924-0136 VL - 210 IS - 15 SP - 2188 EP - 2196 PB - Elsevier CY - Amsterdam ER - TY - JOUR A1 - Mukherjee, Krishnendu A1 - Prahl, Ulrich A1 - Bleck, Wolfgang A1 - Reisgen, Uwe A1 - Schleser, Markus A1 - Abdurakhmanov, Aydemir T1 - Characterization and modelling techniques for gas metal arc welding of DP 600 sheet steels JF - Materialwissenschaft und Werkstofftechnik N2 - The objectives of the present work are to characterize the Gas Metal Arc Welding process of DP 600 sheet steel and to summarize the modelling techniques. The time-temperature evolution during the welding cycle was measured experimentally and modelled with the softwaretool SimWeld. To model the phase transformations during the welding cycle dilatometer tests were done to quantify the parameters for phase field modelling by MICRESS®. The important input parameters are interface mobility, nucleation density, etc. A contribution was made to include austenite to bainite transformation in MICRESS®. This is useful to predict the microstructure in the fast cooling segments. The phase transformation model is capable to predict the microstructure along the heating and cooling cycles of welding. Tensile tests have shown the evidence of failure at the heat affected zone, which has the ferrite-tempered martensite microstructure. Y1 - 2010 U6 - http://dx.doi.org/10.1002/mawe.201000692 SN - 1521-4052 VL - 41 IS - 11 SP - 972 EP - 983 PB - Wiley-VCH CY - Weinheim ER - TY - JOUR A1 - Reisgen, Uwe A1 - Schleser, Markus A1 - Mokrov, Oleg A1 - Ahmed, Essam T1 - Shielding gas influences on laser weldability of tailored blanks of advanced automotive steels JF - Applied surface science N2 - The effects of shielding gas types and flow rates on CO2 laser weldability of DP600/TRIP700 steel sheets were studied in this work. The evaluated shielding gases were helium (He), argon (Ar) and different mixtures of He and Ar. Weld penetration, tensile strength and formability (Erichsen test) of laser welds were found to be strongly dependent upon the shielding gas types. The ability of shielding gas in removing plasma plume and thus increasing weld penetration is believed to be closely related to ionization potential and atomic weight which determine the period of plasma formation and disappearance. It was found that the higher helium shielding gas flow rate, the deeper weld penetration and the lower weld width. Y1 - 2010 U6 - http://dx.doi.org/10.1016/j.apsusc.2010.08.042 SN - 0169-4332 (E-Journal); 0169-4332 (Print) VL - 257 IS - 5 SP - 1401 EP - 1406 PB - Elsevier CY - Amsterdam ER - TY - JOUR A1 - Ahmed, Essam A1 - Reisgen, Uwe A1 - Schleser, Markus A1 - Mokrov, Oleg T1 - On formability of tailor laser welded blanks of DP/TRIP steel sheets JF - Science and technology of welding and joining N2 - This paper aims to evaluate the formability of tailor welded blanks of dual phase (DP600)/transformation induced plasticity (TRIP700) steel sheets. In this work, bead on plate butt joints of 2·5 mm DP600 and 1·2 mm TRIP700 steel sheets were performed using CO2 laser beam welding. Microhardness measurements and transverse tensile testing were carried out to characterise the welds. The formability of base metals and welds were investigated by standard Erichsen test. In a perpendicular tensile test to the weld line, all specimens were fractured at the TRIP base metal, and the strengths were somewhat higher than those of base metal. There was a significant reduction in formability caused by welding of the DP600/TRIP700 steel sheets, and the formability increased with increasing welding speed. Y1 - 2010 U6 - http://dx.doi.org/10.1179/136217110X12731414739754 SN - 1743-2936 VL - 15 IS - 5 SP - 337 EP - 342 PB - Maney CY - Leeds ER - TY - JOUR A1 - Haselgruber, Nikolaus A1 - Mautner, Karin A1 - Thiele, Jan T1 - Usage Space Analysis for Reliability Testing JF - Quality and Reliability Engineering International N2 - During the development process of a complex technical product, one widely used and important technique is accelerated testing where the applied stress on a component is chosen to exceed the reference stress, i.e. the stress encountered in field operation, in order to reduce the time to failure. For that, the reference stress has to be known. Since a complex technical product may fail regarding numerous failure modes, stress in general is highly dimensional rather than scalar. In addition, customers use their products individually, i.e. field operation should be described by a distribution rather than by one scalar stress value. In this paper, a way to span the customer usage space is shown. It allows the identification of worst case reference stress profiles in significantly reduced dimensions with minimal loss of information. The application example shows that even for a complex product like a combustion engine, stress information can be compressed significantly. With low measurement effort it turned out that only three reference stress cycles were sufficient to cover a broad range of customer stress variety. Y1 - 2010 U6 - http://dx.doi.org/10.1002/qre.1155 SN - 1099-1638 N1 - Special Issue: Business and Industrial Statistics: Developments and Industrial Practices in Quality and Reliability VL - 26 IS - 8 SP - 877 EP - 885 PB - Wiley CY - New York ER - TY - JOUR A1 - Enning, Manfred A1 - Baier, M. T1 - Energetic and operational use of FlexCargoRail freight wagons in the single wagon load traffic / Baier, M. ; Enning, M. JF - Towards zero emission : EVS 24, the 24th International Battery, Hybrid and Fuel Cell Electric Vehicle Symposium & Exhibition, Stavanger, Norway, May 13 - 16, 2009 ; symposium proceedings / organised by AVERE ... Robert Stüssi [Hrsg.] Y1 - 2009 N1 - European Association of Electric Road Vehicles ; EVS ; (24 : ; 2009.05.13-16 : ; Stavanger) CY - Stavanger ER - TY - JOUR A1 - Pfaff, Raphael A1 - Burnham, Keith J. T1 - On abstraction and interpretability: a behavioural perspective JF - Systems Science Y1 - 2009 SN - 0137-1223 VL - Vol. 35 IS - Iss. 2 SP - 19 EP - 26 ER - TY - JOUR A1 - Seiler, Friedrich A1 - Pichler, Alexander A1 - Pfaff, Raphael A1 - Srulijes, Julio T1 - Novel processing tools for automated doppler picture velocimetry (DPV) evaluation JF - Journal of visualization Y1 - 2009 SN - 1343-8875 VL - Vol. 12 IS - Iss. 4 SP - 323 EP - 337 ER - TY - JOUR A1 - Mautner, Karin A1 - Forster, Ralf A1 - Kornhuber, Ralf A1 - Sander, Oliver T1 - Fast and Reliable Pricing of American Options with Local Volatility / Forster, Ralf ; Kornhuber, Ralf ; Mautner, Karin ; Sander, Oliver JF - Domain Decomposition Methods in Science and Engineering XVII Y1 - 2008 SN - 978-3-540-75198-4 N1 - Lecture Notes in Computational Sciece and Engineering ; 60 SP - 383 EP - 390 ER - TY - JOUR A1 - Kallweit, Stephan A1 - Kaminsky, Radoslav A1 - Rossi, Massimiliano A1 - Morbiducci, Umberto T1 - PIV Measurements of Flows in Artificial Heart Valves / Kaminsky, Radoslav ; Kallweit, Stephan ; Rossi, Massimiliano ; Morbiducci, Umberto ; Scalise, Lorenzo JF - Particle Image Velocimetry - New Developments and Recent Applications Y1 - 2008 SN - 978-3-540-73528-1 N1 - Topics in Applied Physics SP - 55 EP - 72 ER - TY - JOUR A1 - Kallweit, Stephan A1 - Willert, Chris A1 - Dues, Michael A1 - Müller, Ulrich T1 - PIV for Volume Flow Metering / Kallweit, Stephan ; Willert, Chris ; Dues, Michael ; Müller, Ulrich ; Lederer, Thomas Y1 - 2008 N1 - 14th International Symposium on Applications of Laser Techniques to Fluid Mechanics, 2008-07-07 - 2008-07-10, Lisbon (Portugal) SP - 6 S. ER - TY - JOUR A1 - Dilthey, Ulrich A1 - Schleser, Markus A1 - Feldmann, Martin A1 - Pak, Daniel A1 - Geßler, Achim T1 - Investigation of punctiform, plane and hybrid joints of textile-reinforced concrete parts JF - Cement and concrete composites Y1 - 2008 SN - 0958-9465 VL - Vol. 30 IS - iss. 2 SP - 82 EP - 87 ER - TY - JOUR A1 - Kallweit, Stephan A1 - Vanlanduit, S. A1 - Vanherzeele, J. A1 - Brouns, M. T1 - Time resolved PIV reconstruction of periodic flows / Vanlanduit, S. ; Vanherzeele, J. ; Kallweit, S. ; Brouns, M. ; Guillaume, P. JF - PIV'07, 7th International Symposium on Particle Image Velocimetry, Roma, IT, Sep 11-14, 2007 Y1 - 2007 N1 - PIV, Internional Symposium on Particle Image Velocimetry, 7 ; Datei: Vanlanduit.pdf SP - 1 EP - 14 ER - TY - JOUR A1 - Kämper, Klaus-Peter A1 - Picard, A. A1 - Schütze, A. A1 - Wallach, D. T1 - Adopting the Foundry Concept of Semiconductor Fabrication on Educational Schemes and the Virtual Technology Lab (VTL). Picard, A.; Kämper, K.-P.; Schütze, A.; Wallach, D.; Walter, T. JF - Mst-News (2006) Y1 - 2006 SN - 0948-3128 SP - 15, 16 EP - u. 35 ER - TY - JOUR A1 - Enning, Manfred A1 - Stützle, Thorsten A1 - Viereck, Uwe A1 - Stribersky, Anton T1 - Creepage control for use in wheelslide protection systems / Stützle, Thorsten ; Viereck, Uwe ; Stribersky, Anton ; Rulka, Wolfgang ; Enning, Manfred ; Abel, Dirk JF - Control in transportation systems : proceedings of the 11th IFAC symposium on control in transportation systems (CTS 2006), August 29-31, 2006, Delft, the Netherlands / International Federation of Automatic Control Y1 - 2006 SN - 0742-5953 ER - TY - JOUR A1 - Schleser, Markus A1 - Walk-Lauffer, Bernd A1 - Raupach, Michael A1 - Dilthey, Ulrich T1 - Application of polymers for textile-reinforced concrete JF - Journal of materials in civil engineering : properties, applications, durability Y1 - 2006 SN - 0899-1561 VL - 18 IS - 5 SP - 670 EP - 676 ER - TY - JOUR A1 - Feldmann, Markus A1 - Pak, Daniel A1 - Geßler, Achim A1 - Dilthey, Ulrich A1 - Schleser, Markus T1 - Bonded connections for textile reinforced concrete structures JF - Cailiao-gongcheng = Journal of materials engineering Y1 - 2006 SN - 1001-4381 IS - Special iss. SP - 123 EP - 127 ER - TY - JOUR A1 - Gebhardt, Andreas T1 - Generative Manufacturing of Ceramic Parts "Vision Rapid Prototyping" N2 - Table of Contents Introduction 1. Generative Manufacturing Processes 2. Classification of Generative Manufacturing Processes 3. Application of Generative Processes on the Fabrication of Ceramic Parts 3.1 Extrusion 3.2 3D-Printing 3.3 Sintering – Laser Sintering 3.4 Layer-Laminate Processes 3.5 Stereolithography (sometimes written: Stereo Lithography) 4. Layer Milling 5. Conclusion - Vision KW - Rapid prototyping KW - Rapid Technologie KW - Rapid Prototyping Y1 - 2006 ER - TY - JOUR A1 - Enning, Manfred A1 - Zambou, N. A1 - Abel, D. T1 - Longitudinal Control of Following Vehicles within Platoon : A Model-Based Predictive Approach / Zambou, N. ; Enning, M. ; Abel, D. JF - Advances in automotive control 2004 : a proceedings volume from the IFAC symposium, Salerno, Italy, 19 - 23 April 2004 / ed. C. Pianese Y1 - 2005 SN - 0080442501 N1 - International Federation of Automatic Control ; Symposium on Advances in Automotive Control ; (4, 2004, Salerno) SP - 733 EP - 738 PB - Elsevier CY - Oxford ER - TY - JOUR A1 - Kallweit, Stephan A1 - Kaminsky, R. A1 - Rossi, M. A1 - Morbiducci, U. T1 - Time resolved PIV technique for high temporal resolution measurements of prosthetic heart valves fluid dynamics / Kaminsky, R. ; Rossi, M. ; Morbiducci, U. ; Scalise, L. ; Catellini, P. ; Kallweit, S. ; Verdonck, P. ; Grigioni, M. JF - The International Journal of Artificial Organs. 28 (2005), H. 9 Y1 - 2005 SN - 1724-6040 N1 - Abstracts: XXXII Annual ESAO Congress, 5-8 October 2005, Bologna - Italy SP - 946 ER - TY - JOUR A1 - Kallweit, Stephan A1 - Kaminsky, R. A1 - Rossi, M. A1 - Morbiducci, U. T1 - 2D PIV Study of the flow downstream : Two prototypes of a ney monoleaflet artificial aortic heart valve prosthesis / Kaminsky, R. ; Kramm, K. ; Weber, H. J. ; Simons, A. P. ; Kallweit, S. ; Verdonck, P. R. JF - The International Journal of Artificial Organs. 28 (2005), H. 9 Y1 - 2005 SN - 1724-6040 N1 - Abstracts: XXXII Annual ESAO Congress, 5-8 October 2005, Bologna - Italy SP - 921 ER - TY - JOUR A1 - Kallweit, Stephan A1 - Kaminsky, R. A1 - Rossi, M. A1 - Morbiducci, U. T1 - 3D PIV measurements of prosthetic heart valve dynamics / Kaminsky, R. ; Rossi, M. ; Morbiducci, U. ; Scalise, L. ; Castellini, P. ; Kallweit, S. ; Verdonck, P. ; Grigioni, M. JF - The International Journal of Artificial Organs. 28 (2005), H. 9 Y1 - 2005 SN - 1724-6040 N1 - Abstracts: XXXII Annual ESAO Congress, 5-8 October 2005, Bologna - Italy SP - 868 ER - TY - JOUR A1 - Kallweit, Stephan A1 - Kaminsky, R. A1 - Rossi, M. A1 - Scalise, L. T1 - PIV Measurements with high temporal Resolution behind Artificial Heart Valves / Kaminsky, R. ; Rossi, M. ; Scalise, L. ; Kallweit, S. ; Verdonck, P. JF - Proceedings of the 6th International Symposium on Particle Image Velocimetry Y1 - 2005 N1 - link zum abstract PB - Caltech CY - Pasadena, CA ER - TY - JOUR A1 - Gebhardt, Andreas T1 - Rapid Prototyping JF - Landolt-Börnstein - Group VIII Advanced Materials and Technologies‡Vol. 1 Laser Physics and Applications‡Subvol. C Laser Applications / authors: Bäuerle, D. ... Y1 - 2004 SN - 3-540-00105-0 SP - 105 EP - 123 PB - Heidelberg CY - Springer ER - TY - JOUR A1 - Enning, Manfred A1 - Zambou, Nathan A1 - Abel, Dirk T1 - Nonlinear spacing control of following vehicles within platoon a controlled lagrangian approach / Zambou, Nathan ; Enning, Manfred ; Abel, Dirk JF - NOLCOS, IFAC Symposium on Nonlinear Control Systems Y1 - 2004 N1 - NOLCOS, 2004, IFAC Symposium on Nonlinear Control Systems, 6th, Stuttgart, DE, 2004-09-01 - 2004-09-03 SP - 1211 EP - 1216 ER - TY - JOUR A1 - Dilthey, Ulrich A1 - Brandenburg, Annette A1 - Schleser, Markus T1 - Dispensing and application of unfilled adhesives in the micro range JF - Welding and cutting. 3 (2004), H. 4 Y1 - 2004 SN - 1612-3433 SP - 250 EP - 254 ER - TY - JOUR A1 - Kämper, Klaus-Peter A1 - Picard, Antoni A1 - Brill, Manfred A1 - Cassel, Detlef (u.a.) T1 - The Virtual Cleanroom – a new tool in teaching MST process technologies JF - mst news International newsletter on micro - nano Integration (2003) Y1 - 2003 SN - 0948-3128 SP - 35 EP - 36 ER - TY - JOUR A1 - Kämper, Klaus-Peter T1 - Education and Training in MST. Kämper, K.-P.; Picard, A.; Brill, M.; Cassel, D.; Jentsch, A.; Merten, S.; Rollwa, M. JF - Mst-News (2003) Y1 - 2003 SN - 0948-3128 SP - 35 ER - TY - JOUR A1 - Enning, Manfred A1 - Mann, S. A1 - Bollig, A. A1 - Kaierle, S. T1 - Autonomous Production Cell for Laser Beam Welding / Mann S. ; Bollig, A. ; Kaierle, S. ; Abel, D. ; Poprawe, R. Y1 - 2003 SN - 0912035757 N1 - ICALEO 2003, Florida ; Laser Materials Processing Conference ; (2003, Jacksonville, Fla.) ; ICALEO ; (22, 2003, Jacksonville, Fla.) PB - LIA CY - Orlando, Fla ER - TY - JOUR A1 - Kallweit, Stephan A1 - Schimpf, Axel T1 - Photogrammetric Particle Image Velocimetry / Schimpf, Axel ; Kallweit, Stephan JF - Particle image velocimetry : recent improvements; proceedings of the Europiv 2 Workshop held in Zaragoza, Spain, March 31 - April 1, 2003 / edited by M. Stanislas ... Y1 - 2003 SN - 3-540-21423-2 SP - 295 PB - Springer CY - Berlin ER - TY - JOUR A1 - Kämper, Klaus-Peter A1 - Picard, Antoni A1 - Brill, Manfred A1 - Cassel, Detlev A1 - Jentsch, Andreas A1 - Merten, Sabine A1 - Rollwa, Markus T1 - The Virtual Clean Room - a new tool in teaching MST process technologies N2 - The Virtual Clean Room - a new tool in teaching MST process technologies University education in high-technology fields like MST is not complete without intensive laboratory sessions. Students cannot fully grasp the complexity and the special problems related to the manufacturing of microsystems without a thorough hands-on experience in a MST clean room. KW - Virtuelle Maschine KW - VM KW - Mikrosystemtechnik KW - MST KW - virtual clean room Y1 - 2003 ER - TY - JOUR A1 - Gebhardt, Andreas A1 - Schmidt, Frank-Michael T1 - Practical experiences with making and finishing of coloured models using 3D printing Y1 - 2002 N1 - International Conference on Rapid Prototyping and Manufacturing <2, 2002, Beijing> ER - TY - JOUR A1 - Gebhardt, Andreas T1 - Rapid Prototyping and PIV Y1 - 2001 N1 - Workshop on Industrial Applications of Particle Image Velocimetry <2001, Köln> ER - TY - JOUR A1 - Gebhardt, Andreas T1 - Laserwelding with fillerwire JF - LIA handbook of laser material processing / Laser Institute of America Y1 - 2001 SN - 3-540-41770-2 N1 - Chapter 11.2.12 CY - Orlando, Florida ER - TY - JOUR A1 - Enning, Manfred A1 - Hücker, Jan A1 - Jenayeh, Imad A1 - Rake, Heinrich T1 - A Parametric Identification Scheme for a Self-tuning Industrial Compact Controller - INTERKAMA 1999 / Hucker, Jan ; Jenayeh, Imad ; Enning, Manfred ; Rake, Heinrich Y1 - 1999 N1 - ISA TP99UN139 ; Proceedings ISA-Tech Conference, Düsseldorf 1999 ER - TY - JOUR A1 - Kämper, Klaus-Peter A1 - Berg, U. A1 - Begemann, M. A1 - Hagemann, B. (u.a.) T1 - Series production and testing of a micro motor. Serienfertigung und Prüfung eines Mikromotors JF - Actuator 98 : 6th International Conference on New Actuators ; 17 - 19 June, 1998, Bremen, Germany ; conference proceedings / ed.: Hubert Borgmann ... Y1 - 1998 SN - 3-933339-00-6 N1 - Konferenz-Einzelbericht: ACTUATOR, Internat. Conf. on New Actuators SP - 552 EP - 555 PB - Messe Bremen CY - Bremen ER - TY - JOUR A1 - Kämper, Klaus-Peter A1 - Döpper, J. A1 - Ehrfeld, W. A1 - Oberbeck, S. T1 - A self-filling low-cost membrane micropump JF - Proceedings : an investigation of micro structures, sensors, actuators, machines and systems / sponsored by the IEEE Robotics and Automation Society in cooperation with the ASME Dynamic Systems and Control Division Y1 - 1998 SN - 078034412X N1 - International Workshop on Micro-Electro-Mechanical Systems <11, 1998, Heidelberg> SP - 432 EP - 437 PB - IEEE Service Center CY - Piscataway, NJ ER - TY - JOUR A1 - Kämper, Klaus-Peter A1 - Abraham, M. A1 - Ehrfeld, W. A1 - Hessel, V. T1 - Microsystem technology: Between research and industrial application. Abraham, M.; Ehrfeld, W.; Hessel, V.; Kämper, K.-P.; Lacher, M.; Picard, A. JF - Microelectronic Engineering. 41-42 (1998) Y1 - 1998 SN - 0167-9317 N1 - International Conference on Micro- and Nanofarbication SP - 47 EP - 52 ER - TY - JOUR A1 - Enning, Manfred A1 - Jenayeh, I. A1 - Müller, C. A1 - Kositza, N. T1 - Mechatronics in automating shunting processes in marshalling yards / Jenayeh, I. ; Müller, C.; Kositza, N. ; Enning, M. ; Rake, H. JF - Mechatronics '98 : proceedings of the 6th UK Mechatronics Forum International Conference, Skövde, Sweden, 9-11 September 1998 Y1 - 1998 SN - 0-08-043339-1 N1 - UK Mechatronics Forum International Conference (6 : 1998 : Skövde) PB - Pergamon CY - Amsterdam ER - TY - JOUR A1 - Enning, Manfred A1 - Jenayeh, I. A1 - Müller, C. A1 - Kositza, N. T1 - A New Approach for Automating Shunting Processes in Marshalling Yards / Jenayeh, I.; Müller, C. ; Kositza, N. ; Enning, M. ; Rake, H. JF - Computational Engineering in Systems Applications : 2nd IMACS International Multiconference CESA'98; [abstracts; Nabeul-Hammamet, Tunisia, April 1 - 4, 1998] / ed. by Pierre Borne Y1 - 1998 SP - 338 EP - 343 PB - UCIS CY - Villeneuve d'Ascq ER - TY - JOUR A1 - Kallweit, Stephan A1 - Uchiyama, R. A1 - Siekmann, H. T1 - Fault Diagnostic Method for Pump Running Conditions Based on Process Modeling and Neural Network / Uchiyama, R. ; Kallweit, S. ; Siekmann, H. JF - International Journal of Rotating Machinery. 4 (1998), H. 1 Y1 - 1998 SN - 1542-3034 SP - 49 EP - 59 ER - TY - JOUR A1 - Kämper, Klaus-Peter A1 - Döpper, J. A1 - Clemens, M. A1 - Ehrfeld, W. T1 - Micro gear pumps for dosing of viscous fluids. / Döpper, J. (u.a.) JF - Journal of Micromechanics and Microengineering. 7 (1997), H. 3 Y1 - 1997 SN - 0960-1317 SP - 230 EP - 232 ER - TY - JOUR A1 - Kämper, Klaus-Peter A1 - Ehrfeld, W. A1 - Döpper, J. A1 - Hessel, V. T1 - Microfluidic components for biological and chemical microreactors. Kämper, K.-P.; Ehrfeld, W.; Döpper, J.; Hessel, V.; Lehr, H.; Löwe, H.; Richter, T.; Wolf, A. JF - Proceedings : an investigation of micro structures, sensors, actuators, machines and robots ; Nagoya, Japan, January 26 - 30, 1997 / IEEE Robotics and Automation Society ... Y1 - 1997 SN - 0-7803-3744-1 N1 - International Workshop on Micro-Electro-Mechanical Systems <10, 1997, Nagoya> SP - 338 EP - 343 PB - IEEE Service Center CY - Piscataway, NJ ER - TY - JOUR A1 - Kämper, Klaus-Peter A1 - Ehrfeld, W. A1 - Hessel, V. A1 - Lacher, M. T1 - Market oriented development and production of microdevices. Ehrfeld, W.; Hessel, V.; Kämper, K.-P.; Lacher, M.; Picard, A.; Schmidt, M.; Schulz, C. JF - Proceedings : 21th International Conference on Microelectronics : MIEL '97 ; Niš, Yugoslavia, 14-17 September 1997. Vol. 1 Y1 - 1997 SN - 0-7803-3664-X SP - 71 EP - 79 PB - IEEE Service Center CY - Piscataway, NJ ER - TY - JOUR A1 - Kämper, Klaus-Peter A1 - Lehr, H. A1 - Ehrfeld, W. A1 - Hagemann, B. T1 - Development of micro and millimotors. Lehr, H.; Ehrfeld, W.; Hagemann, B.; Kämper, K.-P.; Michel, F.; Schulz, C.; Thürigen C. JF - Minimally Invasive Therapy and Allied Technologies. 6 (1997) Y1 - 1997 SN - 1364-5706 ER - TY - JOUR A1 - Enning, Manfred A1 - Jenayeh, I. A1 - Müller, C. A1 - Rake, Heinrich T1 - Development and realization of a manipulator for automatic decoupling of freight cars in marshalling yards / Jenayeh, I. ; Müller, C. ; Enning, Manfred ; Rake, Heinrich ; Peter, J. Y1 - 1997 N1 - World Congress on Railway Research, Florenz, 16.-19.11.1997, 1997 ER - TY - JOUR A1 - Kämper, Klaus-Peter A1 - Lehr, H. A1 - Abel, S. A1 - Döpper, J. T1 - Microactuators as driving units for microrobotic systems. Herstellung von Mikroaktoren mit dem LIGA-Verfahren für Mikroroboter / Lehr, H.; Abel, S.; Döpper, J.; Ehrfeld, W.; Hagemann, B.; Kämper, K.-P.; Michel, F.; Schulu, c.; Thürigen, C. JF - Proceedings of the SPIE - The International Society for Optical Engineering Y1 - 1996 SN - 0277-786X N1 - Konferenz-Einzelbericht. SP - 202 EP - 210 ER - TY - JOUR A1 - Kämper, Klaus-Peter T1 - Development of low-cost injection moulded micropumps. Entwicklung von kostengünstigen, mittels Spritzguß hergestellten Mikropumpen / Döpper, J. (u.a.) JF - Actuator 96 : Conference Proceedings ; 5th International Conference on New Actuators ; 26- 28 June, Bremen, Germany / Ed.: Hubert Borgmann. Publ. by: AXON Technology Consult GmbH Y1 - 1996 N1 - Konferenz-Einzelbericht: ACTUATOR, Internat. Conf. on New Actuators, 5 SP - 37 EP - 40 CY - Bremen ER - TY - JOUR A1 - Kämper, Klaus-Peter A1 - Ehrfeld, W. A1 - Hagemann, B. A1 - Lehr, H. T1 - Electromagnetic permanent magnet micromotor with integrated micro gear box. Kämper, K.-P.; Ehrfeld, W.; Hagemann, B.; Lehr, H.; Michel, F.; Schirling, A.; Thürigen, C.; Wittig, T. JF - Actuator 96 : Conference Proceedings ; 5th International Conference on New Actuators ; 26- 28 June, Bremen, Germany / Ed.: Hubert Borgmann. Publ. by: AXON Technology Consult GmbH Y1 - 1996 N1 - International Conference on New Actuators <5, 1996, Bremen> SP - 429 CY - Bremen ER - TY - JOUR A1 - Klocke, Martina T1 - Study Units in the CIM-Oriented Study Factory JF - Qualification for Computer-Integrated Manufacturing. Hrsg.: Felix Rauner Y1 - 1995 SN - 3-540-19971-3 SP - 38 EP - 51 PB - Springer CY - Berlin [u.a.] ER - TY - JOUR A1 - Kämper, Klaus-Peter A1 - Lehr, H. A1 - Abel, S. A1 - Ehrfeld, W. T1 - Assembly of Electromagnetic Milliactuators with LIGA Components. Lehr, H.; Abel, S.; Ehrfeld, W.; Hagemann, B.; Kämper, K.-P.; Michel, F.; Thürigen, C. JF - Proceedings 2nd Japan-France Congress on Mechatronics, Takamatsu (Kagawa, Japan) 1.-3. November 1994, 31 (1994) Y1 - 1995 N1 - 2nd Japan-France Congress on mechatronics (1994 Nov : Takamatsu, Japan) SP - 31 EP - 31 PB - Fuji Technology Press ER - TY - JOUR A1 - Kämper, Klaus-Peter A1 - Döpper, J. A1 - Ehrfeld, W. A1 - Hagemann, B. T1 - Simulation supported design of LIGA Microsystems. Kämper, K.-P.; Döpper, J.; Ehrfeld, W.; Hagemann, B.; Hill, S.D.J.; Lehr, H. JF - Simulation and design of microsystems and microstructures : [... contains the papers presented at the First International Conference on the Simulation and Design of Microsystems and Microstructures, MicroSIM '95, which was held in Southampton, UK, in September 1995] / [organised by: Wessex Institute of Technology, UK]. Ed.: R. A. Adey Y1 - 1995 SN - 1-85312-390-0 SP - 3 EP - 10 PB - Computational Mechanics Publ. CY - Southampton [u.a.] ER - TY - JOUR A1 - Kämper, Klaus-Peter A1 - Döpper, J. A1 - Ehrfeld, W. A1 - Hagemann, B. T1 - An investigation of computer modelling for micro-injection moulding. Hill, S.D.J.; Kämper, K.-P.; Dasbach, U.; Döpper, J.; Ehrfeld, W.; Kaupert, M. JF - Simulation and design of microsystems and microstructures : [... contains the papers presented at the First International Conference on the Simulation and Design of Microsystems and Microstructures, MicroSIM '95, which was held in Southampton, UK, in September 1995] / [organised by: Wessex Institute of Technology, UK]. Ed.: R. A. Adey Y1 - 1995 SN - 1-85312-390-0 SP - 275 PB - Computational Mechanics Publ. CY - Southampton [u.a.] ER - TY - JOUR A1 - Kämper, Klaus-Peter A1 - Hagemann, B. A1 - Lehr, H. A1 - Michel, F. T1 - LIGA Example 2: Electromagnetic Micromotor. Hagemann, B.; Kämper, K.-P.; Lehr, H.; Michel, F.; Thürigen, C. JF - LIGA technique / Hans-Dieter Bauer (ed.). [Developed by UETP-MEMS, University Training Partnership for Micro-Electro-Mechanical Systems ...]. - 2.ed. Y1 - 1995 N1 - University Enterprise Training Partnership for Micro-Electro-Mechanical Systems SP - 100 EP - 110 PB - FSRM CY - Neuchatel ER - TY - JOUR A1 - Starke, Günther A1 - Drews, P. T1 - Le soudage au siecle de l'informatique JF - Souder. 18 (1994), H. 6 Y1 - 1994 SN - 0246-1900 SP - 33 EP - 44 ER - TY - JOUR A1 - Starke, Günther T1 - Welding in the century of information technology. Session 1 JF - Welding in the World. 34 (1994), H. 9 Y1 - 1994 SN - 0043-2288 SP - 1 EP - 20 ER - TY - JOUR A1 - Kämper, Klaus-Peter A1 - Lehr, H. A1 - Ehrfeld, W. A1 - Michel, F. T1 - LIGA Components for the Construction of Milliactuators. Lehr, H.; Ehrfeld, W.; Kämper, K.-P.; Michel, F.; Schmidt, M. JF - 1994 IEEE Symposium on Emerging Technologies & Factory Automation : novel disciplines for the next century ; proceedings, November 6 - 10, 1994, Tokyo, Japan / ETFA '94. Hiroyuki Fujita [chairman] ... Sponsored by: Institute of Industrial Science, SEIKEN Y1 - 1994 SN - 0780321146 SP - 43 EP - 47 CY - Piscataway, N.J. ER - TY - JOUR A1 - Kämper, Klaus-Peter A1 - Schulz, C. A1 - Ehrfeld, W. A1 - Erbel, R. T1 - LIGA Fabricated Microsystems for Medical and Related Applications. Schulz, C.; Ehrfeld, W.; Erbel, R.; Kämper, K.-P.; Koch, L.; Lehr, H.; Roth, T. JF - 3-Day Course on Microengineering in Medicine and Biology and its Applications to Minimally Invasive Techniques for Therapy and Medical Diagnosis : EURO-BME 94; October 5, 6, and 7, 1994, Swiss Federal Institute of Technology, EPFL, Lausanne, Switzerland / [the 1994 EURO-BME Microengineering in Medicine and Biology Training Course. Staff: Christian D. Depeursinge ...] Y1 - 1994 N1 - Microengineering in Medicine and Biology Training Course 1994, Lausanne PB - REPRO EPFL CY - Lausanne ER - TY - JOUR A1 - Enning, Manfred A1 - Bernhard, S. A1 - Rake, H. T1 - Automation of a laboratory plant for direct casting of thin steel strips / Bernhard, S. ; Enning, M. ; Rake, H. JF - Control Engineering Practice. 2 (1994), H. 6 Y1 - 1994 SN - 0967-0661 SP - 961 EP - 967 ER -