TY - CHAP A1 - Šakić, Bogdan A1 - Milijaš, Aleksa A1 - Marinković, Marko A1 - Butenweg, Christoph A1 - Klinkel, Sven ED - Papadrakakis, Manolis ED - Fragiadakis, Michalis T1 - Influence of prior in-plane damage on the out-of-plane response of non-load bearing unreinforced masonry walls under seismic load T2 - 8th ECCOMAS Thematic Conference on Computational Methods in Structural Dynamics and Earthquake Engineering N2 - Reinforced concrete frames with masonry infill walls are popular form of construction all over the world as well in seismic regions. While severe earthquakes can cause high level of damage of both reinforced concrete and masonry infills, earthquakes of lower to medium intensity some-times can cause significant level of damage of masonry infill walls. Especially important is the level of damage of face loaded infill masonry walls (out-of-plane direction) as out-of-plane load cannot only bring high level of damage to the wall, it can also be life-threating for the people near the wall. The response in out-of-plane direction directly depends on the prior in-plane damage, as previous investigation shown that it decreases resistance capacity of the in-fills. Behaviour of infill masonry walls with and without prior in-plane load is investigated in the experimental campaign and the results are presented in this paper. These results are later compared with analytical approaches for the out-of-plane resistance from the literature. Conclusions based on the experimental campaign on the influence of prior in-plane damage on the out-of-plane response of infill walls are compared with the conclusions from other authors who investigated the same problematic. KW - Earthquake Engineering KW - Unreinforced masonry walls KW - Out-of-plane load KW - In- plane damage KW - Out-of-plane failure Y1 - 2021 SN - 9786188507258 U6 - http://dx.doi.org/10.7712/120121.8527.18913 SN - 2623-3347 N1 - COMPDYN 2021 28-30 June 2021, Streamed from Athens, Greece SP - 808 EP - 828 PB - National Technical University of Athens CY - Athen ER - TY - THES A1 - Zosgornik, Julia T1 - Temporärer, mobiler Lebensraum: ein Wohnkonzept für Tinyhouses aus alten, ungenutzten Bahnwaggons N2 - Das Olympiagelände in München wurde im Jahre 1972 durch die Münchener S-Bahn erreichbar. Nach der Nutzung während der Olympischen Spiele wurde die Strecke weiterhin von der Linie S3angefahren, aber schließlich 1988 stillgelegt und steht seither unter Denkmalschutz. Das umfassende Gelände ist bis heute gut ausgebaut und bietet viel Raum für Freizeitaktivitäten. Nun bietet sich dieser Standort für ein neues Wohnkonzept an. Aus alten, nicht mehr nutzbaren Bahnwaggons entstehen Tinyhouse-Module. Aus dem alten Olympiabahnhof der S3 wird ein neues Viertel für junge Leute, Studenten und alle anderen, die sich vorstellen können in einem Tinyhouse zu wohnen. KW - Wohnkonzept KW - Denkmalschutz KW - Bahnwaggons KW - Tinyhouse-Module Y1 - 2021 PB - FH Aachen CY - Aachen ER - TY - THES A1 - Zaunbrecher, Fabienne T1 - Living Spaces - By OASE: Konzeption eines Flagship-Stores mit Wohlfühl- und Erlebnis-Spaces N2 - Konzeption eines Flagship-Stores mit Wohlfühl- und Erlebnis-Spaces Die Bedürfnisse von Besuchern und Kunden eines Geschäfts haben sich über die letzten Jahre stark verändert. Sie möchten das ihr Kauf zum Erlebnis wird. Auf Basis dieser Erkenntnis wurde im Rahmen dieser Arbeit zusammen mit den Produkten des Weltmarktführers für Teichtechnik und Aquaristik „OASE – Living Water“ ein Storekonzept geschaffen. Dieses verbindet den Verkaufsraum mit unterschiedlichen Erlebniswelten, welche auf die jeweilig ausgestellte Produktkategorie abgestimmt sind. Zusätzlich eröffnet ein diverser und aufregend gestalteter Gartenbereich der zum Entspannen und Verweilen einlädt. Der herausstechende Aspekt des Konzepts ist, dass die Produkte sowohl als reines Produkt, als auch in verbauter Version in Aktion zu sehen sind. Auf diese Art bietet die Marke „OASE – Living Water“ ein neues Kauf-Erlebnis an. KW - Storekonzept KW - Verkaufsraum KW - Teichtechnik KW - Aquaristik KW - Wasser Y1 - 2021 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER - TY - JOUR A1 - Zabirov, Alexander A1 - Schleser, Markus A1 - Bucherer, Sebastian T1 - Füge- und Dichtkonzept für einen Leichtbauverbrennungsmotor JF - adhäsion KLEBEN & DICHTEN Y1 - 2021 U6 - http://dx.doi.org/10.1007/s35145-021-0531-5 SN - 2192-8681 VL - 65 IS - 11 SP - 12 EP - 19 PB - Springer Nature CY - Cham ER - TY - JOUR A1 - Yoshinobu, Tatsuo A1 - Schöning, Michael Josef T1 - Light-addressable potentiometric sensors (LAPS) for cell monitoring and biosensing JF - Current Opinion in Electrochemistry Y1 - 2021 U6 - http://dx.doi.org/10.1016/j.coelec.2021.100727 SN - 2451-9103 IS - In Press, Journal Pre-proof PB - Elsevier CY - Amsterdam ER - TY - THES A1 - Yilmaz, Dilara T1 - Deutsches Hygiene-Museum Dresden: Entwicklung und Konzeption eines neuen Erscheinungsbildes N2 - In Zeiten der COVID-19-Pandemie ist die Aufklärung der Bevölkerung, besonders in Hygiene- und Gesundheitsfragen, wichtiger denn je. Das Deutsche Hygiene-Museum macht sich genau das zur Aufgabe. Unter Einbeziehung des Museumsprofils „Das Museum vom Menschen“ und der Architektur zwischen Bauhaus und Neoklassizismus erhält das Museum ein neues Erscheinungsbild. Dabei wird der Sammlungsaspekt gezielt visualisiert, denn das Museum zeichnet sich durch einen umfangreichen Sammlungsbestand aus. Die heterogene Sammlungsbreite macht es europaweit zu einem Unikat. Da das Museum einen Teil des Gesundheitssystems darstellt, ist das überwiegend rot gehaltene Corporate Design und die Wort-Bild-Marke eine Anlehnung an das Deutsche Rote Kreuz. Das medienübergreifende Erscheinungsbild unterstreicht somit die Werte und Besonderheiten des Museums und hat zusätzlich den Auftrag, über Hygiene und Gesundheit aufzuklären. KW - Hygiene KW - Museum KW - Neoklassizismus KW - Gesundheit KW - Forschung Y1 - 2021 PB - FH Aachen CY - Aachen ER - TY - THES A1 - Wrutniak, Sophia Stefanie T1 - Monitoring-System für die Luftrettung: ergonomisches Designkonzept für den medizinischen Anwender N2 - Bei einem Luftrettungseinsatz hat die Herstellung der Transportfähigkeit des Patienten Priorität. Im Anschluss erfolgt das Monitoring während des Fluges. Das Problem dabei ist: Es gibt keine einheitliche Basis zur ergonomischen Nutzung und Datenverwertung der medizinischen Geräte. Kabel, Positionierung und individuelle Displays beeinträchtigen die Anwendenden. Dies kann im schlimmsten Fall die erfolgreiche Patientenbehandlung gefährden und die Übergabe des Patienten verzögern. Im Konzept wurden die Geräte drahtlos gestaltet. Mittels Knopfdruck am Gerät werden Daten an den Monitor übertragen. Schnell und sicher können EKG, Blutdruck, SPO2 und Temperatur gemessen und Stethoskop, Ultraschall und Videolaryngoskop verwendet werden. Ein Barcode-Scanner dokumentiert Medikamente und verbrauchte Materialien. Im Anschluss wird ein Zielkrankenhaus ausgewählt, die Ankunftszeit angezeigt und Daten protokolliert und übertragen. KW - Luftrettung KW - Diagnostik KW - Ergonomie KW - medizinische Geräte KW - Medical Design Y1 - 2021 PB - FH Aachen CY - Aachen ER - TY - THES A1 - Wild, Lisa T1 - UKIYO: Eine Neuinterpretation der fließenden Welt N2 - Ukiyo kommt aus dem Japanischen und bedeutet übersetzt so viel wie: „Den Moment leben, ohne von den Sorgen des Lebens berührt zu werden.“ Gerade in Zeiten der Pandemie verliert man oft den Blick für das Schöne im Leben. Der Fotoband „UKIYO“ soll dazu anregen, alltägliche Dinge aus einem neuen Blickwinkel zu betrachten und die Schönheit im Vergänglichen zu erkennen. Die Fotografien sind inspiriert durch das japanische Kunstgenre Ukiyo-e, was wörtlich übersetzt etwa „Bilder der heiteren, fließenden Welt“ heißt. Die Gestaltung des Bildbandes orientiert sich an verschiedenen japanischen Stilmitteln, wie zum Beispiel Wabi-Sabi (die Schönheit im Unvollkommenen) und Mono no aware (eine melancholische Mischung aus Freude, Trauer und Hinnahme). „UKIYO“ nimmt die Betrachter mit auf eine kleine Reise durch die fließende Welt.  KW - Fotografie KW - Japan KW - Ukiyo KW - Bildband KW - Fotoband Y1 - 2021 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER - TY - THES A1 - Wichmann, Hanna T1 - Bordsteinkanten: Dokumentation über das Leben als Mensch mit einer Behinderung N2 - Fast jeder zehnte Mensch in Deutschland hat eine Behinderung. Dennoch gibt es gegenüber diesen Personen eine Menge Vorurteile und unangemessenes Verhalten. Dieses Projekt befasst sich mit der Frage, wie Menschen mit einer Behinderung leben, wie sie denken und welche Rolle Barrieren in ihrem Alltag spielen. Dazu wurden Personen mit unterschiedlichen Lebenseinstellungen und Behinderungen porträtiert. Die Arbeit dokumentiert, inwieweit die Behinderung in ihr Leben und in ihre Persönlichkeit mit einspielt. Die Bilderserie in Kombination mit einem Textteil als Printmedium wird ergänzt durch eine Audiodatei. Dieses Zusammenspiel ist wichtig, um eine Barrierefreiheit der Arbeit zu gewährleisten. Auch die Bindungsform und Schriftgestaltung orientieren sich an barrierefreier Gestaltung. Das Projekt trägt dazu bei, Barrieren aufzuheben - sowohl in unseren Köpfen als auch an Bordsteinkanten. KW - Behinderung KW - Inklusion KW - Teilhabe KW - Selbstbestimmung KW - Dokumentation Y1 - 2021 PB - FH Aachen CY - Aachen ER - TY - JOUR A1 - Wert, Stefan A1 - Iken, Heiko A1 - Schöning, Michael Josef A1 - Matysik, Frank-Michael T1 - Development of a temperature‐pulse enhanced electrochemical glucose biosensor and characterization of its stability via scanning electrochemical microscopy JF - Electroanalysis N2 - Glucose oxidase (GOx) is an enzyme frequently used in glucose biosensors. As increased temperatures can enhance the performance of electrochemical sensors, we investigated the impact of temperature pulses on GOx that was drop-coated on flattened Pt microwires. The wires were heated by an alternating current. The sensitivity towards glucose and the temperature stability of GOx was investigated by amperometry. An up to 22-fold increase of sensitivity was observed. Spatially resolved enzyme activity changes were investigated via scanning electrochemical microscopy. The application of short (<100 ms) heat pulses was associated with less thermal inactivation of the immobilized GOx than long-term heating. Y1 - 2021 U6 - http://dx.doi.org/10.1002/elan.202100089 SN - 1521-4109 IS - Early View PB - Wiley-VCH CY - Weinheim ER - TY - JOUR A1 - Werkhausen, Amelie A1 - Willwacher, Steffen A1 - Albracht, Kirsten T1 - Medial gastrocnemius muscle fascicles shorten throughout stance during sprint acceleration JF - Scandinavian Journal of Medicine & Science in Sports N2 - The compliant nature of distal limb muscle-tendon units is traditionally considered suboptimal in explosive movements when positive joint work is required. However, during accelerative running, ankle joint net mechanical work is positive. Therefore, this study aims to investigate how plantar flexor muscle-tendon behavior is modulated during fast accelerations. Eleven female sprinters performed maximum sprint accelerations from starting blocks, while gastrocnemius muscle fascicle lengths were estimated using ultrasonography. We combined motion analysis and ground reaction force measurements to assess lower limb joint kinematics and kinetics, and to estimate gastrocnemius muscle-tendon unit length during the first two acceleration steps. Outcome variables were resampled to the stance phase and averaged across three to five trials. Relevant scalars were extracted and analyzed using one-sample and two-sample t-tests, and vector trajectories were compared using statistical parametric mapping. We found that an uncoupling of muscle fascicle behavior from muscle-tendon unit behavior is effectively used to produce net positive mechanical work at the joint during maximum sprint acceleration. Muscle fascicles shortened throughout the first and second steps, while shortening occurred earlier during the first step, where negative joint work was lower compared with the second step. Elastic strain energy may be stored during dorsiflexion after touchdown since fascicles did not lengthen at the same time to dissipate energy. Thus, net positive work generation is accommodated by the reuse of elastic strain energy along with positive gastrocnemius fascicle work. Our results show a mechanism of how muscles with high in-series compliance can contribute to net positive joint work. KW - locomotion KW - muscle mechanics KW - running KW - sprint start KW - ultrasonography Y1 - 2021 U6 - http://dx.doi.org/10.1111/sms.13956 SN - 0905-7188 (Druckausgabe) SN - 1600-0838 (Onlineausgabe) VL - 31 IS - 7 SP - 1471 EP - 1480 PB - Wiley-Blackwell CY - Oxford ER - TY - JOUR A1 - Welden, Rene A1 - Nagamine Komesu, Cindy A. A1 - Wagner, Patrick H. A1 - Schöning, Michael Josef A1 - Wagner, Torsten T1 - Photoelectrochemical enzymatic penicillin biosensor: A proof-of-concept experiment JF - Electrochemical Science Advances N2 - Photoelectrochemical (PEC) biosensors are a rather novel type of biosensors thatutilizelighttoprovideinformationaboutthecompositionofananalyte,enablinglight-controlled multi-analyte measurements. For enzymatic PEC biosensors,amperometric detection principles are already known in the literature. In con-trast, there is only a little information on H+-ion sensitive PEC biosensors. Inthis work, we demonstrate the detection of H+ions emerged by H+-generatingenzymes, exemplarily demonstrated with penicillinase as a model enzyme on atitanium dioxide photoanode. First, we describe the pH sensitivity of the sensorand study possible photoelectrocatalytic reactions with penicillin. Second, weshow the enzymatic PEC detection of penicillin. KW - enzymatic biosensor KW - penicillin KW - penicillinase KW - photoelectrochemistry KW - titanium dioxide photoanode Y1 - 2021 U6 - http://dx.doi.org/10.1002/elsa.202100131 SN - 2698-5977 N1 - Corresponding auhtor: Michael J. Schöning VL - 2 IS - 4 SP - 1 EP - 5 PB - Wiley-VCH CY - Weinheim ER - TY - JOUR A1 - Welden, Rene A1 - Jablonski, Melanie A1 - Wege, Christina A1 - Keusgen, Michael A1 - Wagner, Patrick Hermann A1 - Wagner, Torsten A1 - Schöning, Michael Josef T1 - Light-Addressable Actuator-Sensor Platform for Monitoring and Manipulation of pH Gradients in Microfluidics: A Case Study with the Enzyme Penicillinase JF - Biosensors N2 - The feasibility of light-addressed detection and manipulation of pH gradients inside an electrochemical microfluidic cell was studied. Local pH changes, induced by a light-addressable electrode (LAE), were detected using a light-addressable potentiometric sensor (LAPS) with different measurement modes representing an actuator-sensor system. Biosensor functionality was examined depending on locally induced pH gradients with the help of the model enzyme penicillinase, which had been immobilized in the microfluidic channel. The surface morphology of the LAE and enzyme-functionalized LAPS was studied by scanning electron microscopy. Furthermore, the penicillin sensitivity of the LAPS inside the microfluidic channel was determined with regard to the analyte’s pH influence on the enzymatic reaction rate. In a final experiment, the LAE-controlled pH inhibition of the enzyme activity was monitored by the LAPS. KW - microfluidics KW - enzyme kinetics KW - actuator-sensor system KW - light-addressable electrode KW - light-addressable potentiometric sensor Y1 - 2021 U6 - http://dx.doi.org/10.3390/bios11060171 SN - 2079-6374 N1 - This article belongs to the Special Issue "Selected Papers from the 1st International Electronic Conference on Biosensors (IECB 2020)" VL - 11 IS - 6 PB - MDPI CY - Basel ER - TY - THES A1 - Weber, Jana T1 - Botanischer Garten und Botanisches Museum Berlin: Entwicklung eines neuen Erscheinungsbildes N2 - Die Pflanzenvielfalt der Erde steht im Fokus aller Aktivitäten am Botanischen Garten und Botanischen Museum Berlin (BGBM). Umfangreiche wissenschaftliche Sammlungen bilden zusammen mit den historischen Garten- und Gewächshausanlagen, dem Museum und einer modernen Forschungsinfrastruktur die Grundlage für die dortige Arbeit. Darüber hinaus trägt das BGBM mit seinen Forschungs- und Entwicklungsprojekten zu nationalen und internationalen Biodiversitätsprogrammen bei. Umso wichtiger ist es, der Einrichtung ein klares und modernes Auftreten zu geben. Das neue Erscheinungsbild lässt Garten und Museum durch eine rahmende Typografie zu einer Einheit werden und kommuniziert so auch gleichzeitig das Leitbild der Einrichtung, als „Schaufenster in die Pflanzenwelt“ zu dienen. Es positioniert das BGBM zum einen als wissenschaftliche Institution und zum anderen als farbenfrohes Ausflugsziel und Erholungsort. KW - Gestaltung KW - Botanik KW - Pflanzenwelt KW - Botanischer Garten KW - Umwelt Y1 - 2021 PB - FH Aachen CY - Aachen ER - TY - JOUR A1 - Waldvogel, Janice A1 - Ritzmann, Ramona A1 - Freyler, Kathrin A1 - Helm, Michael A1 - Monti, Elena A1 - Albracht, Kirsten A1 - Stäudle, Benjamin A1 - Gollhofer, Albert A1 - Narici, Marco T1 - The Anticipation of Gravity in Human Ballistic Movement JF - Frontiers in Physiology N2 - Stretch-shortening type actions are characterized by lengthening of the pre-activated muscle-tendon unit (MTU) in the eccentric phase immediately followed by muscle shortening. Under 1 g, pre-activity before and muscle activity after ground contact, scale muscle stiffness, which is crucial for the recoil properties of the MTU in the subsequent push-off. This study aimed to examine the neuro-mechanical coupling of the stretch-shortening cycle in response to gravity levels ranging from 0.1 to 2 g. During parabolic flights, 17 subjects performed drop jumps while electromyography (EMG) of the lower limb muscles was combined with ultrasound images of the gastrocnemius medialis, 2D kinematics and kinetics to depict changes in energy management and performance. Neuro-mechanical coupling in 1 g was characterized by high magnitudes of pre-activity and eccentric muscle activity allowing an isometric muscle behavior during ground contact. EMG during pre-activity and the concentric phase systematically increased from 0.1 to 1 g. Below 1 g the EMG in the eccentric phase was diminished, leading to muscle lengthening and reduced MTU stretches. Kinetic energy at take-off and performance were decreased compared to 1 g. Above 1 g, reduced EMG in the eccentric phase was accompanied by large MTU and muscle stretch, increased joint flexion amplitudes, energy loss and reduced performance. The energy outcome function established by linear mixed model reveals that the central nervous system regulates the extensor muscles phase- and load-specifically. In conclusion, neuro-mechanical coupling appears to be optimized in 1 g. Below 1 g, the energy outcome is compromised by reduced muscle stiffness. Above 1 g, loading progressively induces muscle lengthening, thus facilitating energy dissipation. Y1 - 2021 U6 - http://dx.doi.org/10.3389/fphys.2021.614060 SN - 1664-042X PB - Frontiers CY - Lausanne ER - TY - THES A1 - Wahlefeld, Leon T1 - Generative Gestaltung: wie eine Herangehensweise die Zukunft des Designs revolutionieren könnte. N2 - Diese Bachelorarbeit setzt sich mit der „Generativen Gestaltung“ und ihren Möglichkeiten für Gestaltende auseinander. Die automatisierte Bearbeitung eines gestalterischen Projektes soll vorrangig Vorteile beim Arbeiten mit großen Datenmengen bieten. Ziel war es, eine Plakatreihe zu entwerfen, die auf der Grundlage eines Codes - also eines strikten Regelwerks - basiert. Mithilfe dieses Verfahrens kann auf Knopfdruck eine beliebige Menge an Plakaten generiert werden. Durch die Festlegung bestimmter Parameter innerhalb des Codes wird gewährleistet, dass jedes ausgespielte Plakat anders ist als sein Vorgänger. Diese Arbeit dient als eine erste anskizzierte Grundlage dafür, wie grafischer Output automatisiert und vor allem aktualisiert generiert werden kann. Dieses Prinzip kann auf eine Vielzahl von Inhalten und Umsetzungen angewendet werden. KW - Layout KW - Plakat KW - Generativ KW - Satellitenbilder KW - Processing Y1 - 2021 PB - FH Aachen CY - Aachen ER - TY - THES A1 - Vorholt, Lara T1 - Fitted Fashion: Sizing-Lösung zur Steigerung der Konversion & Reduzierung von E-Commerce-Retouren N2 - Die Zahl der Nutzenden beim Onlineshopping ist in den letzten Jahren deutlich gewachsen. Eines der größten Probleme dabei: Die Retouren. Sowohl die Wirtschaft als auch die Umwelt leiden darunter. Der Hauptgrund für Rücksendungen sind dabei Schwierigkeiten bei der Auswahl der individuell richtigen Größe. Das Ziel dieses Projektes ist es daher, eine 3D-Körperscan-App zu erstellen. Mit dieser ist es möglich, einen auf die eigenen Körpermaße angepassten Avatar zu erstellen und eine angepasste Stilberatung für die jeweilige Körperform angeboten zu bekommen. Zudem gibt es eine Applikation in Form eines Software Development Kits, welches in Onlineshops eingebunden werden kann. Mit Hilfe der Applikation bekommen Konsumenten die richtige Größe auch beim Onlineshopping angezeigt und tätigen so weniger Fehlkäufe. Dies bringt nicht nur Vorteile für die Umwelt mit sich und den Unternehmen eine massive Kostenersparnis durch die Einsparung von Retouren, Müll und Personal, sondern schlussendlich auch eine zufriedenere Kundschaft. KW - Lidarscanner KW - Mode KW - Innovation KW - Nachhaltig KW - E-Commerce Y1 - 2021 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER - TY - THES A1 - Vels, Lina T1 - Bauwerk Stadt: Konzeption eines digitalen Informationsmediums zum Thema Urban Mining N2 - Architekten und Ingenieure entwerfen häufig Gebäude, ohne zu berücksichtigen, wie die verwendeten Baumaterialien nach ihrer Nutzung zurückgeführt werden können. Daher gelangen Rohstoffe über den Lebenszyklus eines Produkts nicht hinaus oder nicht in den Produktionsprozess zurück. »Bauwerk Stadt« ist ein digitaler Leitfaden, der durch Bewertungssysteme zur Klassifizierung von Produkten beiträgt und so den Wert sowie die potenzielle Abbauwürdigkeit des Materials ermittelt. Ebenso wird auf der Webseite ein umfassendes Bild der Thematik vermittelt: von der Planung über die Realisierung bis hin zum Rückbau. Durch dokumentarische Texte in modularen Boxen und animierte Grafiken, die selbst zur Architektur werden, werden gewissenhaft Informationen dargeboten. Die dynamisch gestaltete Webseite soll bei der Planung zum nachhaltigen Bauen helfen und so umsetzbare Handlungsmöglichkeiten aufzeigen sowie das Recyceln unterstützen. KW - Städtischer Bergbau KW - Informationsdesign KW - Recycling KW - Webseite KW - Nachhaltiges Bauen Y1 - 2021 PB - FH Aachen CY - Aachen ER - TY - JOUR A1 - Valero, Daniel A1 - Schalko, Isabella A1 - Friedrich, Heide A1 - Abad, Jorge D. A1 - Bung, Daniel B. A1 - Donchyts, Gennadii A1 - Felder, Stefan A1 - Ferreira, Rui M. L. A1 - Hohermuth, Benjamin A1 - Kramer, Matthias A1 - Li, Danxun A1 - Mendes, Luis A1 - Moreno-Rodenas, Antonio A1 - Nones, Michael A1 - Paron, Paolo A1 - Ruiz-Villanueva, Virginia A1 - Wang, Ruo-Qian A1 - Franca, Mario J. T1 - Pathways towards democratization of hydro-environment observations and data JF - Iahr White Paper Series Y1 - 2021 IS - 1 SP - 1 EP - 9 PB - International Association for Hydro-Environment Engineering and Research (IAHR) ER - TY - CHAP A1 - Ulmer, Jessica A1 - Braun, Sebastian A1 - Wollert, Jörg T1 - Adaptive VR-Produktionsumgebungen für Evaluations- und Schulungstätigkeiten T1 - Adaptive VR production environments for evaluation and training purposes T2 - Automation 2021: Navigating towards resilient Production N2 - Industrie 4.0 stellt viele Herausforderungen an produzierende Unternehmen und ihre Beschäf-tigten. Innovative und effektive Trainingsstrategien sind erforderlich, um mit den sich schnell verändernden Produktionsumgebungen und neuen Fertigungstechnologien Schritt halten zu können. Virtual Reality (VR) bietet neue Möglichkeiten für On-the-Job, On-Demand- und Off-Premise-Schulungen. Diese Arbeit stellt ein neues VR Schulungssystem vor, welches sich flexible an unterschiedliche Trainingsobjekte auf Grundlage von Rezepten und CAD Modellen anpassen lässt. Das Konzept basiert auf gerichteten azyklischen Graphen und einem Level-system. Es ermöglicht eine benutzerindividuelle Lerngeschwindigkeit mittels visueller Ele-mente. Das Konzept wurde für einen mechanischen Anwendungsfall mit Industriekomponen-ten implementiert und in der Industrie 4.0-Modellfabrik der FH Aachen umgesetzt. N2 - Industry 4.0 poses many challenges for manufacturing companies and their employees. Inno-vative and effective training strategies are needed to keep pace with rapidly changing produc-tion environments and new manufacturing technologies. Virtual reality (VR) offers new oppor-tunities for on-the-job, on-demand, and off-premise training. This work presents a new VR training system that can be flexibly adapted to different training objects based on recipes and CAD models. The concept is based on directed acyclic graphs and a level system. It allows a user-individual learning speed by means of visual elements. The concept was implemented for a mechanical use case with industrial components and implemented in the industry 4.0 model factory of the FH Aachen University of Applied Sciences. Y1 - 2021 SN - 978-3-18-092392-5 U6 - http://dx.doi.org/10.51202/9783181023921-55 SN - 0083-5560 N1 - 22. Leitkongress der Mess- und Automatisierungstechnik, 9. und 30. Juni 2021. SP - 55 EP - 64 PB - VDI CY - Düsseldorf ER - TY - CHAP A1 - Ulmer, Jessica A1 - Braun, Sebastian A1 - Cheng, Chi-Tsun A1 - Dowey, Steve A1 - Wollert, Jörg T1 - Adapting Augmented Reality Systems to the users’ needs using Gamification and error solving methods T2 - Procedia CIRP N2 - Animations of virtual items in AR support systems are typically predefined and lack interactions with dynamic physical environments. AR applications rarely consider users’ preferences and do not provide customized spontaneous support under unknown situations. This research focuses on developing adaptive, error-tolerant AR systems based on directed acyclic graphs and error resolving strategies. Using this approach, users will have more freedom of choice during AR supported work, which leads to more efficient workflows. Error correction methods based on CAD models and predefined process data create individual support possibilities. The framework is implemented in the Industry 4.0 model factory at FH Aachen. KW - Augmented Reality KW - Adaptive Systems KW - Gamification KW - Error Recovery Y1 - 2021 U6 - http://dx.doi.org/10.1016/j.procir.2021.11.024 SN - 2212-8271 N1 - Part of special issue: 54th CIRP CMS 2021 - Towards Digitalized Manufacturing 4.0 VL - 104 SP - 140 EP - 145 PB - Elsevier CY - Amsterdam ER - TY - THES A1 - Türeyenler, Bahadir T1 - Dying Craft: die aussterbende Handwerkskunst N2 - Die Buchbinderei ist eine besonders faszinierende Handwerkskunst, da sie ein besonderes Augenmerk auf Detailliertheit, Individualität und Design legt. Mit diesen Charakteristiken hebt sie sich bewusst von den üblichen erhältlichen, massenproduzierten Büchern ab. Seit Jahren geht die Anzahl der Personen, die den Beruf dieses Kunsthandwerks erlernen, stark zurück. Besonders die aktuelle Pandemie zeigt die Unsicherheiten, die mit dieser Arbeit verbunden sind. In der Dokumentation "Dying Craft" wird daher die Besonderheiten dieses Berufs gezeigt, mehr Öffentlichkeit dafür geschaffen und ganz besonders die Begeisterung dafür weitergegeben. KW - Handwerk KW - Buchbinderei KW - Dokumentation KW - Aachen KW - Kunsthandwerk Y1 - 2021 PB - FH Aachen CY - Aachen ER - TY - BOOK A1 - Trümpener, Nora A1 - Peters, Jan A1 - Herzel, Manuel A1 - Vollmann, Alina A1 - Breuer, Gina ED - Kroll-Ludwigs, Kathrin ED - Bassen-Metz, Yasmine ED - Eggert, Mathias ED - Fritz, Thomas ED - Höhne, Tim ED - Tran, Duc Hung ED - Vogt, Jürgen T1 - Aachener Online-Schriften Wirtschaft und Recht. Band 3/2021 N2 - Inhaltsverzeichnis 1. Die ordentliche Kündigung chronisch Kranker im Anwendungsbereich des KSchG – Nora Trümpener 3-56 2. Die Legitimationswirkung der Gesellschafterliste - Erfolg trotz Grenzen? – Jan Peters 57-112 3. Marktmanipulation – Arten, Abgrenzung und gesetzliche Handhabe – Manuel Herzel 113-170 4. Die Zulässigkeit der Verdachtskündigung im Arbeitsverhältnis – Alina Vollmann 171-248 5. Praxisorientierter Arbeitgeberleitfaden zur rechtssicheren Einführung von Homeoffice im Arbeitsverhältnis – Gina Breuer 249-304 T3 - Aachener Online-Schriften Wirtschaft und Recht - 3 Y1 - 2021 PB - FH Aachen / Fachbereich Wirtschaftswissenschaften CY - Aachen ER - TY - THES A1 - Tran, Thuy Tien T1 - Shaping the Future of E-Government: Design System zur Implementierung digitaler öffentlicher Services N2 - Der digitale Transformationsprozess ist einer der größten gesellschaftlichen Umbrüche in der Geschichte der Menschheit. Aufgrund der Corona-Pandemie stieg die Nutzung von digitalen Kanälen bei den Bürger:innen wie nie zuvor und führt zu einem sprunghaften Anstieg der Nachfrage nach öffentlichen Services in digitaler Form. Das Ziel dieser Bachelorarbeit ist es, einen digitalen Raum zu gestalten, der den analogen Weg zum Amt größtenteils erspart. Mit geeigneten Kommunikationskanälen kann auf die Bedürfnisse unterschiedlicher Gruppen eingegangen werden. Die Entwicklung der Anwendung IDport bietet sowohl private als auch staatliche Einsparpotenziale. Bürokratische Aufwände sollen durch eine neue Art des E-Government beseitigt werden. Die Konzeption ist infolge der aktuellen Gegebenheit in Deutschland weit entfernt von einer realitätsnahen Umsetzung, weshalb es sich bei der Anwendung um eine revolutionäre Zukunftsvision handelt. KW - E-Government KW - Design System KW - Revolution KW - Zukunftsvision KW - Optimierung Y1 - 2021 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER - TY - JOUR A1 - Tran, Ngoc Trinh A1 - Staat, Manfred T1 - Direct plastic structural design under random strength and random load by chance constrained programming JF - European Journal of Mechanics - A/Solids Y1 - 2021 U6 - http://dx.doi.org/10.1016/j.euromechsol.2020.104106 SN - 0997-7538 VL - 85 IS - Article 104106 PB - Elsevier CY - Amsterdam ER - TY - CHAP A1 - Tran, Ngoc Trinh A1 - Staat, Manfred T1 - FEM shakedown analysis of Kirchhoff-Love plates under uncertainty of strength T2 - Proceedings of UNCECOMP 2021 N2 - A new formulation to calculate the shakedown limit load of Kirchhoff plates under stochastic conditions of strength is developed. Direct structural reliability design by chance con-strained programming is based on the prescribed failure probabilities, which is an effective approach of stochastic programming if it can be formulated as an equivalent deterministic optimization problem. We restrict uncertainty to strength, the loading is still deterministic. A new formulation is derived in case of random strength with lognormal distribution. Upper bound and lower bound shakedown load factors are calculated simultaneously by a dual algorithm. Y1 - 2021 SN - 978-618-85072-6-5 U6 - http://dx.doi.org/10.7712/120221.8041.19047 N1 - Proceedings of UNCECOMP 2021, 4th International Conference on Uncertainty Quantification in Computational Sciences and Engineering, streamed from Athens, Greece, 28–30 June 2021. SP - 323 EP - 338 ER - TY - JOUR A1 - Tran, Duc Hung A1 - Ebeling, Felix T1 - Die risikoadäquate Bestimmung von Eigenkapitalkosten bei konzerninternen Routinefunktionen JF - Der Betrieb N2 - Eigenkapitalkosten sind eine wesentliche Determinante bei der Wertbestimmung von Unternehmen und Unternehmensteilen. Die Eigenkapitalkosten werden regelmäßig mittels des CAPM bestimmt. Für sog. konzerninterne Routinefunktionen mit geringem Risiko stellt diese Bestimmung mittels CAPM ein Problem dar, da börsennotierte Peergroups für eine zuverlässige Bestimmung des Beta-Faktors meist nicht identifizierbar sind. Damit ergeben sich bei Bewertungen von Routineunternehmen Unsicherheiten und Konfliktpotenzial in steuerlichen Betriebsprüfungen. Dieser Beitrag gibt einen Überblick der in der Praxis genutzten Ansätze und stellt eine theoretische Fundierung zur Bestimmung der Eigenkapitalkosten von konzerninternen Routinefunktionen vor. Dabei wird verdeutlicht, dass Eigenkapitalkosten von konzerninternen Routinefunktionen nicht denen des Gesamtkonzerns entsprechen und Praktikeransätze eine grundsätzliche Berechtigung besitzen. Y1 - 2021 SN - 0005-9935 VL - 74 IS - 29 SP - 1553 EP - 1560 ER - TY - BOOK A1 - Tings, Franziska A1 - Lehner, Julian A1 - Hoß, Elena A1 - Gotzens, Franziska A1 - Creutz, Marie-Sophie A1 - Christ, Nils ED - Kroll-Ludwigs, Kathrin ED - Bassen-Metz, Yasmine ED - Eggert, Mathias ED - Fritz, Thomas ED - Höhne, Tim ED - Tran, Duc Hung ED - Vogt, Jürgen T1 - Aachener Online-Schriften Wirtschaft und Recht. Band 02/2021 N2 - Inhaltsverzeichnis 1. Die Haftung des GmbH-Geschäftsführers in der Insolvenz - Grundsätze und Modifikationen infolge der Covid-19 Pandemie – Franziska Tings 3-61 2. Disquotale Gewinnausschüttung in der Organschaft – Die Neuregelung des § 14 Abs. 2 KStG und die Auslegung durch die Finanzverwaltung – Julian Lehner 62-149 3. Auswirkungen des Mauracher Entwurfs auf die Gesellschaft bürgerlichen Rechts – Neuerfindung oder bloße Korrektur des Personengesellschaftsrechts? – Elena Hoß 150-209 4. Befristung von Arbeitsverhältnissen - Rechtliche Rahmenbedingungen und arbeitsmarktpolitische Chancen und Risiken – Franziska Gotzens 210-270 5. Die Rolle der psychischen Gesundheit am Arbeitsplatz Entwicklung exemplarischer Handlungsempfehlungen für den ganzheitlichen Umgang mit psychischen Belastungen im Homeoffice – Marie-Sophie Creutz 271-346 6. Tokenisierung von illiquiden Vermögenswerten – Wie Blockchain die Immobilienwirtschaft verändern kann – Nils Christ 347-404 T3 - Aachener Online-Schriften Wirtschaft und Recht - 2 Y1 - 2021 PB - FH Aachen / Fachbereich Wirtschaftswissenschaften CY - Aachen ER - TY - JOUR A1 - Timme, Michael T1 - Rechtsprechungsübersicht zum Wohnraummietrecht JF - Monatsschrift für Deutsches Recht Y1 - 2021 U6 - http://dx.doi.org/10.9785/mdtr-2021-750113 SN - 2194-4202 VL - 75 IS - 1 SP - 6 EP - 11 PB - Verlag Dr. Otto Schmidt CY - Köln ER - TY - BOOK A1 - Timme, Michael T1 - BGB Crashkurs: der sichere Weg durch die Prüfung N2 - Dieser "Crashkurs" eignet sich ausgezeichnet für die kompakte Wiederholung und die zielgerichtete Prüfungsvorbereitung. Das Buch ist aufgrund seiner fallbezogenen Ausrichtung vor allem für Anfänger gedacht, eignet sich aber auch für fortgeschrittene Studierende zur kompakten Wiederholung. Einfache Merksätze, Fälle, Übersichten, Definitionen und kurze Zusammenfassungen lassen sich leicht einprägen und geben Sicherheit für die Prüfung. Vorteile auf einen Blick: Das wichtigste BGB-Know-how als Repetitorium vor der Prüfung, mit erprobten Merksätzen und kurzen Zusammenfassungen, Fall für Fall sicher durch die Prüfung Y1 - 2021 SN - 978-3-406-77349-5 PB - C.H. Beck CY - München ET - 6. Auflage ER - TY - THES A1 - Thomaschik, Annika T1 - Medical Design for Kids: Integration der Bedürfnisse von Kindern in medizinische Produkte N2 - Kinder im Kontext von medizinischen Einrichtungen. Kinder sind keine kleinen Erwachsenen und erfordern einen auf sie angepassten Zugang zu medizinischen Behandlungsabläufen. Das Konzept basiert auf dem Gestaltungsprinzip des „Child Centered Design“ mit Befragungen von Experten der Pädiatrie und Forschung sowie mit enger Zusammenarbeit mit Kindern. Entstanden ist ein Produkt welches Skepsis und Angst junger Patienten im Alter von 6 bis 14 Jahren bei stationären Aufenthalten in Krankenhäusern mindert und ihren Heilungsprozess positiv unterstützt. Unter Einbezug von digitalen Möglichkeiten wie Augmented Reality erklärt „ViU“, ein Krankenhaus-Companion in Eulen-Optik, den kleinen Patienten Funktionen und das Wirken verschiedenster medizinischer Geräte und Behandlungen. So wird nicht nur der Rate an Traumata durch Krankenhausaufenthalte bei Kindern entgegengewirkt, sondern auch das Krankenhauspersonal im Umgang mit Kindern im Klinikalltag entlastet. KW - Medizin KW - Technik KW - Kinder KW - Krankenhaus KW - Pädiatrie Y1 - 2021 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER - TY - THES A1 - Theisen, Paul T1 - Die ästhetische Tonalität des Jazz : Immersion durch 3D-Visualisierung und musikalische Interaktion N2 - Das Ausstellungskonzept »Free Jazz: A Collective Improvisation« widmet sich der ästhetischen Tonalität des gleichnamigen Albums von Ornette Coleman. Das besagte Album bildete den Grundstein für die Etablierung des Free Jazz – einer Musikform, die sich durch ihre schrille, hierarchiefreie Klangwelt sowie ein freies Improvisationsspiel auszeichnet und mit den gängigen Konventionen des Jazz bricht. Zu jedem der 8 Musiker, welche gemeinsam das von Coleman zusammengestellte Doppelquartett ergeben, wurden individuell abgestimmte, animierte und interaktive 3D-Gebilde konzipiert. Diese reagieren auf den Sound der jeweiligen Instrumente sowie die Position der Besuchenden und ermöglichen einen audiovisuellen, immersiven Zugang zum Album. Die Interaktion zwischen dem Publikum und den Gebilden schafft Raum für eine kollektive Improvisation auf sowohl der visuellen als auch auditiven Ebene. KW - Musik KW - Jazz KW - Improvisation KW - Immersion KW - Animation Y1 - 2021 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER - TY - JOUR A1 - Temiz Artmann, Aysegül A1 - Kurulgan demirci, Eylem A1 - Fırat, Ipek Seda A1 - Oflaz, Hakan A1 - Artmann, Gerhard T1 - Recombinant activated protein C (rhAPC) affects lipopolysaccharide-induced mechanical compliance changes and beat frequency of mESC-derived cardiomyocyte monolayers JF - SHOCK KW - Septic cardiomyopathy KW - LPS KW - cardiomyocyte biomechanics KW - CellDrum KW - actin cytoskeleton Y1 - 2021 U6 - http://dx.doi.org/10.1097/SHK.0000000000001845 SN - 1540-0514 PB - Wolters Kluwer CY - Köln ER - TY - RPRT A1 - Stölzle-Feix, Sonja A1 - Thomas, Ulrich A1 - Engelstädter, Max A1 - Goßmann, Matthias A1 - Linder, Peter A1 - Staat, Manfred A1 - Raman, Aravind Hariharan A1 - Jung, Alexander A1 - Fertig, Niels T1 - Plattformtechnologie für kardiale Sicherheitspharmakologie basierend auf teilsynthetischem Herzmuskelgewebe (FLEXcyte) : gemeinsamer FuE-Abschlussbericht aller Partner des Verbundprojektes : Projektlaufzeit: 01.10.2018 bis 30.09.2020 Y1 - 2021 U6 - http://dx.doi.org/10.2314/KXP:1813208581 N1 - Förderkennzeichen BMBF 02P18K020-021 Verbundnummer 01185221 PB - Nanion Technologies GmbH CY - München ER - TY - JOUR A1 - Stäudle, Benjamin A1 - Seynnes, Olivier A1 - Laps, Guido A1 - Göll, Fabian A1 - Brüggemann, Gert-Peter A1 - Albracht, Kirsten T1 - Recovery from achilles tendon repair: a combination of Postsurgery Outcomes and Insufficient remodeling of muscle and tendon JF - Medicine & Science in Sports & Exercise N2 - Achilles tendon rupture (ATR) patients have persistent functional deficits in the triceps surae muscle–tendon unit (MTU). The complex remodeling of the MTU accompanying these deficits remains poorly understood. The purpose of the present study was to associate in vivo and in silico data to investigate the relations between changes inMTU properties and strength deficits inATR patients. Methods: Elevenmale subjects who had undergone surgical repair of complete unilateral ATR were examined 4.6 ± 2.0 (mean ± SD) yr after rupture. Gastrocnemius medialis (GM) tendon stiffness, morphology, and muscle architecture were determined using ultrasonography. The force–length relation of the plantar flexor muscles was assessed at five ankle joint angles. In addition, simulations (OpenSim) of the GM MTU force–length properties were performed with various iterations of MTU properties found between the unaffected and the affected side. Results: The affected side of the patients displayed a longer, larger, and stiffer GM tendon (13% ± 10%, 105% ± 28%, and 54% ± 24%, respectively) compared with the unaffected side. The GM muscle fascicles of the affected side were shorter (32% ± 12%) and with greater pennation angles (31% ± 26%). A mean deficit in plantarflexion moment of 31% ± 10% was measured. Simulations indicate that pairing an intact muscle with a longer tendon shifts the optimal angular range of peak force outside physiological angular ranges, whereas the shorter muscle fascicles and tendon stiffening seen in the affected side decrease this shift, albeit incompletely. Conclusions: These results suggest that the substantial changes in MTU properties found in ATR patients may partly result from compensatory remodeling, although this process appears insufficient to fully restore muscle function. KW - Tendon Rupture KW - Stiffness KW - Simulation KW - Muscle Force KW - Muscle Fascicle Y1 - 2021 U6 - http://dx.doi.org/10.1249/MSS.0000000000002592 SN - 1530-0315 VL - 53 IS - 7 SP - 1356 EP - 1366 PB - American College of Sports Medicine CY - Philadelphia, Pa. ER - TY - JOUR A1 - Stollenwerk, Dominik A1 - Reinkensmeier, Sebastian A1 - Georg, Jörg Heiner A1 - Jungbluth, Christian T1 - „Smartes“ Laden an öffentlich zugänglichen Ladesäulen – Teil 2: USER-Verhalten und -Erwartungen JF - Energiewirtschaftliche Tagesfragen : et ; Zeitschrift für Energiewirtschaft, Recht, Technik und Umwelt Y1 - 2021 SN - 0720-6240 SN - 0013-743X VL - 71 IS - 3 SP - 38 EP - 42 PB - ETV Energieverlag CY - Essen ER - TY - THES A1 - Steinicke, Nicola T1 - Ein Erscheinungsbild für die Deutsche Stiftung Denkmalschutz N2 - Die Deutsche Stiftung Denkmalschutz (DSD) ist die größte, private Stiftung Deutschlands, die sich für die Förderung von unter Denkmalschutz stehenden Objekten einsetzt. Das neugestaltete Erscheinungsbild soll die Fachlichkeit der Organisation herausstellen und zugleich kreativ und kommunikativ eine breite Zielgruppe ansprechen. Die DSD bietet neben der Denkmalerhaltung auch Bildungsangebote für Jung und Alt an, wie auch Veranstaltungen für die Bewusstseinsbildung im Denkmalschutz. Als Sprachrohr zwischen der Stiftung und den Fördernden dient das Magazin MONUMENTE. Denkmalschutz mag für manche uninteressant und eingestaubt wirken, da die Beschäftigung mit bereits Bestehendem und das Verhindern von Verfall belanglos sein könnte. Weiß man allerdings über die Bedeutung für Kultur, Gesellschaft und Wirtschaft, so macht Denkmalschutz eine essenzielle Komponente unserer Kulturlandschaft aus. Die Auseinandersetzung mit der DSD soll das herausstellen und das Bewusstsein für diesen kulturellen Bestandteil des Denkmalschutzes vertiefen.  KW - Erscheinungsbild KW - Magazingestaltung KW - Denkmalschutz KW - Deutsche Stiftung Y1 - 2021 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER - TY - THES A1 - Steffens, Nina T1 - Bahn-Buddy: Informative Gamification Reiseapp für die DB für Kinder N2 - „Bahn-Buddy“ ist eine App, die Kindern bei Bahnfahrten auf unterhaltsame Weise ihre Umgebung näherbringt. Dabei wird mit GPS gearbeitet, um die Inhalte der App auf die jeweilige Bahnstrecke abzustimmen. Verschiedene Minispiele und Infoscreens sollen der Fahrt ein interaktiveres Gefühl verleihen und somit die gefühlte Fahrzeit für die Zielgruppe reduzieren. Den Kindern soll dabei auf eine spielerische Art und Weise Wissen über das Land, aber auch über alternative Verkehrsmittel und den Einfluss des Verkehrs auf die Umwelt vermittelt werden. Ziel ist es, die generelle Erfahrung des Bahnfahrens positiver zu gestalten. Dies soll zu einer frühen Kundenbindung führen und durch den geringeren CO2-Ausstoß bei Reisen mit der Bahn einen positiven Effekt auf die Umwelt haben. KW - Bahn KW - Gamification KW - Nachhaltigkeit KW - UX Design KW - UI Design Y1 - 2021 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER - TY - JOUR A1 - Staat, Manfred T1 - An extension strain type Mohr–Coulomb criterion JF - Rock mechanics and rock engineering N2 - Extension fractures are typical for the deformation under low or no confining pressure. They can be explained by a phenomenological extension strain failure criterion. In the past, a simple empirical criterion for fracture initiation in brittle rock has been developed. In this article, it is shown that the simple extension strain criterion makes unrealistic strength predictions in biaxial compression and tension. To overcome this major limitation, a new extension strain criterion is proposed by adding a weighted principal shear component to the simple criterion. The shear weight is chosen, such that the enriched extension strain criterion represents the same failure surface as the Mohr–Coulomb (MC) criterion. Thus, the MC criterion has been derived as an extension strain criterion predicting extension failure modes, which are unexpected in the classical understanding of the failure of cohesive-frictional materials. In progressive damage of rock, the most likely fracture direction is orthogonal to the maximum extension strain leading to dilatancy. The enriched extension strain criterion is proposed as a threshold surface for crack initiation CI and crack damage CD and as a failure surface at peak stress CP. Different from compressive loading, tensile loading requires only a limited number of critical cracks to cause failure. Therefore, for tensile stresses, the failure criteria must be modified somehow, possibly by a cut-off corresponding to the CI stress. Examples show that the enriched extension strain criterion predicts much lower volumes of damaged rock mass compared to the simple extension strain criterion. Y1 - 2021 U6 - http://dx.doi.org/10.1007/s00603-021-02608-7 SN - 1434-453X N1 - Corresponding author: Manfred Staat VL - 54 IS - 12 SP - 6207 EP - 6233 PB - Springer Nature CY - Cham ER - TY - THES A1 - Spomer, Ruth T1 - Zoologisches Forschungsmuseum Alexander König : Entwicklung eines neuen Erscheinungsbildes N2 - Artenvielfalt erforschen und erklären – So lautet der Leitsatz des Bonner Forschungsmuseums. Durch inszenierte Lebensräume sowie beeindruckende sammlungsbasierte Ausstellungen werden komplexe biologische Phänomene erklärt und die Biodiversitätsforschung für ein breites Publikum zugänglich gemacht. Dabei wird das übergeordnete Ziel verfolgt, das Interesse der Allgemeinheit an zoologischer Wissenschaft zu wecken. Das neue Erscheinungsbild schafft Wiedererkennbarkeit und positioniert das Museum als wissenschaftliche Institution. Dabei stellt die Verknüpfung des Forschungsaspektes und der Artenvielfalt die Basis der Gestaltung dar und kommuniziert die wesentlichen Inhalte. Zudem sorgt ein medienübergreifendes Ordnungssystem für eine bessere Übersicht und erleichtert den Zugang zu komplexen Inhalten. So erhält das Museum eine spannendere, attraktivere Wirkung nach Außen und eine bessere Orientierung im Inneren. KW - Museum KW - Corporate Design KW - Artenvielfalt KW - Biodiversität KW - Wissenschaft Y1 - 2021 PB - FH Aachen CY - Aachen ER - TY - JOUR A1 - Spietz, Peter A1 - Spröwitz, Tom A1 - Seefeldt, Patric A1 - Grundmann, Jan Thimo A1 - Jahnke, Rico A1 - Mikschl, Tobias A1 - Mikulz, Eugen A1 - Montenegro, Sergio A1 - Reershemius, Siebo A1 - Renger, Thomas A1 - Ruffer, Michael A1 - Sasaki, Kaname A1 - Sznajder, Maciej A1 - Tóth, Norbert A1 - Ceriotti, Matteo A1 - Dachwald, Bernd A1 - Macdonald, Malcolm A1 - McInnes, Colin A1 - Seboldt, Wolfgang A1 - Quantius, Dominik A1 - Bauer, Waldemar A1 - Wiedemann, Carsten A1 - Grimm, Christian D. A1 - Hercik, David A1 - Ho, Tra-Mi A1 - Lange, Caroline A1 - Schmitz, Nicole T1 - Paths not taken – The Gossamer roadmap’s other options JF - Advances in Space Research KW - Solar sail KW - Small spacecraft KW - DLR-ESTEC GOSSAMER roadmap for solar sailing KW - GOSSAMER-1 Y1 - 2021 U6 - http://dx.doi.org/10.1016/j.asr.2021.01.044 SN - 0273-1177 VL - 67 IS - 9 SP - 2912 EP - 2956 PB - Elsevier CY - Amsterdam ER - TY - THES A1 - Sorgalla, Jonas T1 - Skidio - die digitale Transformation der Kosmetikindustrie : die Entwicklung eines digitalen Vertriebskanals N2 - Skidio basiert dabei auf dem Konzept, dass das Video für die Kosmetikindustrie das optimale Medium für Produktvorstellungen ist. Der Ausgangspunkt für das Einkaufserlebnis des Nutzers ist daher ein Video-Feed, bestehend aus Kurz- und Live-Videos, die einen direkten Kauf der gezeigten Produkte ermöglichen. So entsteht ein Ort, an dem Nutzer auf eine unterhaltsame Art und Weise Inspiration für die eigene Hautpflege finden können. Dabei ist das Video als Medium nicht nur unterhaltsamer, sondern zugleich auch deutlich informativer als klassische Produktlistings. Die Produktpräsentation wird interaktiver, erlebbarer und deutlich effektiver. Gemeinsam mit Technologien wie einer digitalen Hautanalyse, wird so das Potenzial des E-Commerce für die Beautyindustrie vollständig entfaltet. KW - Kosmetik KW - Einkaufen KW - Ecommerce KW - Digitatlisierung KW - App Y1 - 2021 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER - TY - THES A1 - Sonntag, Jana T1 - Konzeption und Entwicklung einer Corporate Identity und einer Tourismuskampagne für das Siegerland N2 - Im Rahmen meiner Bachelorarbeit werden ich mich mit der Konzeption und Entwicklung einer Corporate Identity für das Siegerland beschäftigen. Weiterhin möchte ich eine Tourismuskampagne für diese Region gestalten. KW - Corporate Identity KW - Tourismuskampagne Y1 - 2021 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER - TY - JOUR A1 - Serror, Martin A1 - Hack, Sacha A1 - Henze, Martin A1 - Schuba, Marko A1 - Wehrle, Klaus T1 - Challenges and Opportunities in Securing the Industrial Internet of Things JF - IEEE Transactions on Industrial Informatics Y1 - 2021 U6 - http://dx.doi.org/10.1109/TII.2020.3023507 SN - 1941-0050 VL - 17 IS - 5 SP - 2985 EP - 2996 PB - IEEE CY - New York ER - TY - JOUR A1 - Seefeldt, Patric A1 - Dachwald, Bernd T1 - Temperature increase on folded solar sail membranes JF - Advances in Space Research Y1 - 2021 U6 - http://dx.doi.org/10.1016/j.asr.2020.09.026 SN - 0273-1177 VL - 67 IS - 9 SP - 2688 EP - 2695 PB - Elsevier CY - Amsterdam ER - TY - THES A1 - Schönlau, Jennifer T1 - Deutsche in der Türkei: Wenn Deutsche in die Türkei auswandern N2 - Warum wandern immer mehr Deutsche in die Türkei aus, obwohl wir denken, dass es uns in Deutschland gut geht? Haben deutsche Auswanderer in der Türkei ein besseres Leben? Diese und weitere Fragen wurden in diesem Projekt genauer beleuchtet. Die Beweggründe der Menschen sind so unterschiedlich wie das Leben selbst. Diese Bachelorarbeit beinhaltet Interviews von früher in Deutschland lebenden Personen, die in die Türkei ausgewandert sind und mit ihnen ihre ganz persönliche Geschichte. Zusammen mit diesem Thema wurde untersucht, wie das aktuelle Leben der Protagonisten in der Türkei ist: soziales Umfeld, das Einleben in eine neue Kultur und die Lebensqualität. Ein persönliches und intimes Interview lag hier besonders im Fokus. Die Arbeit wird mit Fotografien unterstützt, die den Alltag Deutscher in der Türkei zeigen. Mit diesem Projekt werden Vorurteile über die Türkei und die dort lebenden Menschen bestätigt, widerlegt und neue Erkenntnisse zur Frage „warum Deutsche in die Türkei auswandern“ gewonnen. KW - Deutsch KW - Deutschland KW - Türkisch KW - Türkei KW - Kultur Y1 - 2021 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER - TY - THES A1 - Schwinges, Katrin T1 - Der/Die/Das Spielzeug: Gestaltung eines geschlechtsneutralen Spielzeugs N2 - Das Projekt bezieht sich auf das globale Konsumverhalten gegenüber Spielwaren unter den Bedingungen des Gender-Marketings im Hinblick auf die nachteiligen Bedingungen für die Entwicklung des Kindes und der Umwelt. Gestaltet wurde ein Baukastensystem, das sich keiner geschlechtsspezifischen Zuweisung bedient, und so verhindert, dass Kinder, die sich im binären Rollenbild nicht wiederfinden, ausgegrenzt werden. Das Stecksystem ohne Vorgabe einer Anleitung ermöglicht freie Entfaltung beim Spiel und die Förderung der spielerischen und didaktischen Entwicklung eines Kindes. Spielen ist eine Art des Kindes sich und seine Umwelt zu begreifen und sich dazu auszudrücken. Es werden nicht nur Fähigkeiten erprobt, sondern auch Verhaltensweisen angeeignet und Identitätsmerkmale definiert. Dadurch erhält das Spielzeug eine Vorbildfunktion. Dieser Vorbildfunktion soll das entworfene Produkt gerecht werden. KW - Konstruktionsspielzeug KW - Baukastensystem KW - Rollenbild Y1 - 2021 PB - FH Aachen CY - Aachen ER - TY - CHAP A1 - Schulze-Buxloh, Lina A1 - Groß, Rolf Fritz A1 - Ulbrich, Michelle T1 - Digital planning using building information modelling and virtual reality: new approach for students’ remote practical training under lockdown conditions in the course of smart building engineering T2 - Proceedings of International Conference on Education in Mathematics, Science and Technology 2021 N2 - The worldwide Corona pandemic has severely restricted student projects in the higher semesters of engineering courses. In order not to delay the graduation, a new concept had to be developed for projects under lockdown conditions. Therefore, unused rooms at the university should be digitally recorded in order to develop a new usage concept as laboratory rooms. An inventory of the actual state of the rooms was done first by taking photos and listing up all flaws and peculiarities. After that, a digital site measuring was done with a 360° laser scanner and these recorded scans were linked to a coherent point cloud and transferred to a software for planning technical building services and supporting Building Information Modelling (BIM). In order to better illustrate the difference between the actual and target state, two virtual reality models were created for realistic demonstration. During the project, the students had to go through the entire digital planning phases. Technical specifications had to be complied with, as well as documentation, time planning and cost estimate. This project turned out to be an excellent alternative to on-site practical training under lockdown conditions and increased the students’ motivation to deal with complex technical questions. KW - smart building engineering KW - building information modelling KW - virtual reality KW - lockdown conditions KW - emote practical training Y1 - 2021 SN - 978-1-952092-17-6 N1 - April 1-4, 2021 in Antalya, Turkey. SP - 118 EP - 123 PB - ISTES Organization CY - San Antonio, TX ER - TY - CHAP A1 - Schulze-Buxloh, Lina A1 - Groß, Rolf Fritz T1 - Miniature urban farming plant: a complex educational “Toy” for engineering students T2 - The Future of Education 11th Edition 2021 N2 - Urban farming is an innovative and sustainable way of food production and is becoming more and more important in smart city and quarter concepts. It also enables the production of certain foods in places where they usually dare not produced, such as production of fish or shrimps in large cities far away from the coast. Unfortunately, it is not always possible to show students such concepts and systems in real life as part of courses: visits of such industry plants are sometimes not possible because of distance or are permitted by the operator for hygienic reasons. In order to give the students the opportunity of getting into contact with such an urban farming system and its complex operation, an industrial urban farming plant was set up on a significantly smaller scale. Therefore, all needed technical components like water aeriation, biological and mechanical filtration or water circulation have been replaced either by aquarium components or by self-designed parts also using a 3D-printer. Students from different courses like mechanical engineering, smart building engineering, biology, electrical engineering, automation technology and civil engineering were involved in this project. This “miniature industrial plant” was also able to start operation and has now been running for two years successfully. Due to Corona pandemic, home office and remote online lectures, the automation of this miniature plant should be brought to a higher level in future for providing a good control over the system and water quality remotely. The aim of giving the student a chance to get to know the operation of an urban farming plant was very well achieved and the students had lots of fun in “playing” and learning with it in a realistic way. KW - urban farming KW - food production KW - smart engineering KW - 3D printing KW - sustainability Y1 - 2021 N1 - FOE 2021 : The Future of Education International Conference – Fully Virtual Edition; 01.07.2021-02.07.2021; Florence, Italy ER - TY - CHAP A1 - Schulze-Buxloh, Lina A1 - Groß, Rolf Fritz T1 - Interdisciplinary Course Smart Building Engineering: A new approach of teaching freshmen in remote teamwork project under pandemic restrictions T2 - New Perspectives in Science Education -International Conference (virtual event, 18-19 March 2021) N2 - In the context of the Corona pandemic and its impact on teaching like digital lectures and exercises a new concept especially for freshmen in demanding courses of Smart Building Engineering became necessary. As there were hardly any face-to-face events at the university, the new teaching concept should enable a good start into engineering studies under pandemic conditions anyway and should also replace the written exam at the end. The students should become active themselves in small teams instead of listening passively to a lecture broadcast online with almost no personal contact. For this purpose, a role play was developed in which the freshmen had to work out a complete solution to the realistic problem of designing, construction planning and implementing a small guesthouse. Each student of the team had to take a certain role like architect, site manager, BIM-manager, electrician and the technitian for HVAC installations. Technical specifications must be complied with, as well as documentation, time planning and cost estimate. The final project folder had to contain technical documents like circuit diagrams for electrical components, circuit diagrams for water and heating, design calculations and components lists. On the other hand construction schedule, construction implementation plan, documentation of the construction progress and minutes of meetings between the various trades had to be submitted as well. In addition to the project folder, a model of the construction project must also be created either as a handmade model or as a digital 3D-model using Computer-aided design (CAD) software. The first steps in the field of Building information modelling (BIM) had also been taken by creating a digital model of the building showing the current planning status in real time as a digital twin. This project turned out to be an excellent training of important student competencies like teamwork, communication skills, and self -organisation and also increased motivation to work on complex technical questions. The aim of giving the student a first impression on the challenges and solutions in building projects with many different technical trades and their points of view was very well achieved and should be continued in the future. KW - Freshmen KW - roleplay KW - Smart Building Engineering KW - BIM KW - remote teamwork Y1 - 2021 N1 - New Perspectives in Science Education - 10th Edition 18-19 March 2021 Fully Virtual Conference PB - Filodiritto CY - Bologna ER - TY - THES A1 - Schulze, Lasse T1 - SCHRECKLICHES : Eine Comic-Antholologie über alltägliche Ängste N2 - Ängste und Phobien sind vielseitig. Furcht im Alltag spiegelt sich sowohl in spezifischen Objekten als auch in allgemeinen Situationen wider. Für unbetroffene Menschen sind diese Emotionen oft unbegreiflich, irrational und abstrakt. In 15 Bildergeschichten werden verschiedene persönliche Ängste humoristisch illustriert und in einer gebundenen Comic-Anthologie zusammengeführt. Der überzogene, bizarre Zeichenstil demonstriert die empfundene Wahrnehmung bei alltäglichen Ängsten auf eine nicht allzu ernst gemeinte Weise. Zeichnerische Ästhetik, von klassischem Comic-Stil bis zum grafischen Horror, und Storytelling stehen hier im Vordergrund. Lesende finden sich selbst in den absurden Geschichten wieder und werden im besten Fall zum Lachen gebracht. Die Bachelorarbeit SCHRECKLICHES versucht das abstrakte Gefühl der Angst auf nachvollziehbare Art zeichnerisch und mit einer guten Portion Übertreibung zu vermitteln. KW - Comicbuch KW - Angst KW - Phobien KW - Digitale Zeichnung KW - Comic Y1 - 2021 PB - FH Aachen CY - Aachen ER - TY - THES A1 - Schultheis, Anna Laura T1 - EmanziPardon: Sind die Aussagen von Simone de Beauvoir aus ‚Das andere Geschlecht‘ heute noch relevant? N2 - Simone de Beauvoir veröffentlichte 1949 ihr Werk ‚Das andere Geschlecht‘, in welchem sie die subjektiven und objektiven Einschränkungen, Belastungen und die Abhängigkeiten vom Mann darlegt, denen Frauen schon seit tausenden Jahren ausgesetzt waren und sind. Aber wie ist das heute? Sind diese Aussagen überhaupt noch aktuell bzw. relevant? Innerhalb der Publikation werden Kernthesen aber auch Textausschnitte aus ihrem Werk aufgeführt sowie aktuelle Artikel, die sich mit der derzeitigen Lage befassen. Durch das gestalterische Konzept innerhalb der Publikation, haben die Lesenden die Möglichkeit, sich konkret mit genau den Themen zu befassen, die jeweils dem persönlichen Interesse entsprechen. Die Publikation dient als Erinnerung und als Nachschlagewerk, um immer wieder lesen können, welche Kämpfe hinsichtlich der Gleichstellung der Geschlechter bereits gekämpft wurden und welche noch gekämpft werden müssen. KW - Emanzipation KW - Geschlechterungerechtigkeit KW - Simone de Beauvoir KW - Feminismus KW - Frauenrolle Y1 - 2021 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER - TY - CHAP A1 - Schulte, Maximilian A1 - Eggert, Mathias T1 - Predicting hourly bitcoin prices based on long short-term memory neural networks T2 - Proceedings of the International Conference on Wirtschaftsinformatik (WI) 2021 N2 - Bitcoin is a cryptocurrency and is considered a high-risk asset class whose price changes are difficult to predict. Current research focusses on daily price movements with a limited number of predictors. The paper at hand aims at identifying measurable indicators for Bitcoin price movement s and the development of a suitable forecasting model for hourly changes. The paper provides three research contributions. First, a set of significant indicators for predicting the Bitcoin price is identified. Second, the results of a trained Long Short-term Memory (LSTM) neural network that predicts price changes on an hourly basis is presented and compared with other algorithms. Third, the results foster discussions of the applicability of neural nets for stock price predictions. In total, 47 input features for a period of over 10 months could be retrieved to train a neural net that predicts the Bitcoin price movements with an error rate of 3.52 %. Y1 - 2021 N1 - 16th International Conference on Wirtschaftsinformatik, March 2021, Essen, Germany ER - TY - THES A1 - Schrey, Leander T1 - Less Waste Shelf: Ein Möbel zur Reduzierung der häuslich anfallenden Lebensmittelabfälle N2 - Mit dem Projekt wird sich dem Problem der weltweiten Lebensmittelverschwendung angenommen und versucht Abfälle in Privathaushalten primär industrialisierter Staaten zu reduzieren. Mit jährlich 1,3 Milliarden Tonnen landet circa ein Drittel aller weltweit produzierten Lebensmittel im Müll. Einen Großteil dieser Abfälle ist vermeidbar, besonders dort, wo man im Überfluss lebt. Das konzipierte Möbelstück soll die Lagerungsmöglichkeiten des Nutzers optimieren und somit für die Wertschätzung von Lebensmitteln sensibilisieren. Für das Möbelstück werden ausschließlich natürliche Materialien verwendet, welche in ihrer Charakteristik optimal zum Funktionsumfang passen, der für die Lagerung benötigt wird. Das Material Terracotta ermöglicht es, mittels Verdunstungskühlung stromlos Gemüse kalt zu halten. Antibakterielles Holz tötet schädliche Bakterien ab. Die Konstruktion ermöglicht somit eine fachgerechte Lebensmittelagerung und ermöglicht sowohl sehr flexible Nutzung, wie auch leichte Reparatur. KW - Regal KW - Möbel KW - Holz KW - Keramik KW - Lebensmittel Y1 - 2021 PB - FH Aachen CY - Aachen ER - TY - CHAP A1 - Schoutetens, Frederic A1 - Dachwald, Bernd A1 - Heiligers, Jeannette T1 - Optimisation of photon-sail trajectories in the alpha-centauri system using evolutionary neurocontrol T2 - 8th ICATT (International Conference on Astrodynamics Tools and Techniques) 23 - 25 June 2021, Virtual N2 - With the increased interest for interstellar exploration after the discovery of exoplanets and the proposal by Breakthrough Starshot, this paper investigates the optimisation of photon-sail trajectories in Alpha Centauri. The prime objective is to find the optimal steering strategy for a photonic sail to get captured around one of the stars after a minimum-time transfer from Earth. By extending the idea of the Breakthrough Starshot project with a deceleration phase upon arrival, the mission’s scientific yield will be increased. As a secondary objective, transfer trajectories between the stars and orbit-raising manoeuvres to explore the habitable zones of the stars are investigated. All trajectories are optimised for minimum time of flight using the trajectory optimisation software InTrance. Depending on the sail technology, interstellar travel times of 77.6-18,790 years can be achieved, which presents an average improvement of 30% with respect to previous work. Still, significant technological development is required to reach and be captured in the Alpha-Centauri system in less than a century. Therefore, a fly-through mission arguably remains the only option for a first exploratory mission to Alpha Centauri, but the enticing results obtained in this work provide perspective for future long-residence missions to our closest neighbouring star system. Y1 - 2021 N1 - 8th ICATT (International Conference on Astrodynamics Tools and Techniques) 23 - 25 June 2021, Virtual SP - 1 EP - 15 ER - TY - CHAP A1 - Schopen, Oliver A1 - Kemper, Hans A1 - Esch, Thomas T1 - Development of a comparison methodology and evaluation matrix for electrically driven compressors in ICE and FC T2 - Proceedings of the 1st UNITED – Southeast Asia Automotive Interest Group (SAIG) International Conference N2 - In addition to electromobility and alternative drive systems, a focus is set on electrically driven compressors (EDC), with a high potential for increasing the efficiency of internal combustion engines (ICE) and fuel cells [01]. The primary objective is to increase the ICE torque, provided independently of the ICE speed by compressing the intake air and consequently the ICE filling level supported by the compressor. For operation independent from the ICE speed, the EDC compressor is decoupled from the turbine by using an electric compressor motor (CM) instead of the turbine. ICE performances can be increased by the use of EDC where individual compressor parameters are adapted to the respective application area [02] [03]. This task contains great challenges, increased by demands with regard to pollutant reduction while maintaining constant performance and reduced fuel consumption. The FH-Aachen is equipped with an EDC test bench which enables EDC-investigations in various configurations and operating modes. Characteristic properties of different compressors can be determined, which build the basis for a comparison methodology. Subject of this project is the development of a comparison methodology for EDC with an associated evaluation method and a defined overall evaluation method. For the application of this comparison methodology, corresponding series of measurements are carried out on the EDC test bench using an appropriate test device. KW - electro mobility KW - fuel cell KW - internal combustion engine KW - electrically driven compressors Y1 - 2021 SN - 978-3-902103-94-9 N1 - 1st UNITED-SAIG International Conference, 21-22 APR 2021, Chulalongkorn University, Thailand SP - 45 EP - 46 PB - FH Joanneum CY - Graz ER - TY - CHAP A1 - Schneider, Dominik A1 - Wisselink, Frank A1 - Nölle, Nikolai A1 - Czarnecki, Christian ED - Barton, Thomas ED - Müller, Christian T1 - Einfluss von Künstlicher Intelligenz auf Customer Journeys am Beispiel von intelligentem Parken T2 - Künstliche Intelligenz in der Anwendung : Rechtliche Aspekte, Anwendungspotenziale und Einsatzszenarien N2 - Im Konsumentenmarkt entstehen vermehrt neue Anwendungen von Künstlicher Intelligenz (KI). Zunehmend drängen auch Geräte und Dienste in den Markt, die eigenständig über das Internet kommunizieren. Dadurch können diese Geräte und Dienste mit neuartigen KI-basierten Diensten verbessert werden. Solche Dienste können die Art und Weise beeinflussen, wie Kunden kommerzielle Entscheidungen treffen und somit das Kundenerlebnis maßgeblich verändern. Der Einfluss von KI auf kommerzielle Interaktionen wurde bisher noch nicht umfassend untersucht. Basierend auf einem Framework, welches einen ersten Überblick über die Effekte von KI auf kommerzielle Interaktionen gibt, wird in diesem Kapitel der Einfluss von KI auf Customer Journeys am konkreten Anwendungsfall des intelligenten Parkens analysiert. Die daraus gewonnenen Erkenntnisse können in der Praxis als Grundlage genutzt werden, um das Potenzial von KI zu verstehen und bei der Gestaltung eigener Customer Journeys umzusetzen. KW - Kommerzielle Interaktionen KW - Customer Journeys KW - Prozessagilität KW - Customer Experience Management KW - Intelligentes Parken Y1 - 2021 SN - 978-3-658-30935-0 (Print) SN - 978-3-658-30936-7 (Online) U6 - http://dx.doi.org/10.1007/978-3-658-30936-7_7 SP - 99 EP - 122 PB - Springer Vieweg CY - Wiesbaden ER - TY - THES A1 - Schmitz, Jennifer T1 - Inklusives Design: Multisensorisches Branding für sehbehinderte, blinde und sehende Menschen N2 - Multisensorisches Branding bezeichnet die Gestaltung für mindestens zwei Sinne. Diese Bachelorarbeit beinhaltet daher ein Konzept, um sehbehinderten Menschen und Blinden das Branding einer Marke im Bereich der Bekleidungsindustrie zugänglich zu machen. Durch die gezielte Kombination von Haptik und Optik ist im Rahmen dieser Arbeit eine Bekleidungsmarke entstanden, deren Textilien jegliche Informationen für sehbehinderte und blinde Menschen enthalten, ohne dabei auf eine ansprechende Optik für Sehende zu verzichten. Vor allem durch neu entwickelte Open Source Symbole, die fühlbar sind, und einen Barcode wird Betroffenen in Zukunft der Kauf von Bekleidung sowie der Waschvorgang erleichtert. KW - Inklusion KW - Barrierefrei KW - Textilbranche KW - Waschetiketten KW - Haptik Y1 - 2021 PB - FH Aachen CY - Aachen ER - TY - CHAP A1 - Schmidts, Oliver A1 - Kraft, Bodo A1 - Winkens, Marvin A1 - Zündorf, Albert T1 - Catalog integration of heterogeneous and volatile product data T2 - DATA 2020: Data Management Technologies and Applications N2 - The integration of frequently changing, volatile product data from different manufacturers into a single catalog is a significant challenge for small and medium-sized e-commerce companies. They rely on timely integrating product data to present them aggregated in an online shop without knowing format specifications, concept understanding of manufacturers, and data quality. Furthermore, format, concepts, and data quality may change at any time. Consequently, integrating product catalogs into a single standardized catalog is often a laborious manual task. Current strategies to streamline or automate catalog integration use techniques based on machine learning, word vectorization, or semantic similarity. However, most approaches struggle with low-quality or real-world data. We propose Attribute Label Ranking (ALR) as a recommendation engine to simplify the integration process of previously unknown, proprietary tabular format into a standardized catalog for practitioners. We evaluate ALR by focusing on the impact of different neural network architectures, language features, and semantic similarity. Additionally, we consider metrics for industrial application and present the impact of ALR in production and its limitations. Y1 - 2021 SN - 978-3-030-83013-7 U6 - http://dx.doi.org/10.1007/978-3-030-83014-4_7 N1 - International Conference on Data Management Technologies and Applications, DATA 2020, 7-9 July SP - 134 EP - 153 PB - Springer CY - Cham ER - TY - CHAP A1 - Schmidt, Thomas A1 - Kasch, Susanne A1 - Eichler, Fabian A1 - Thurn, Laura T1 - Process strategies on laser-based melting of glass powder T2 - Lasers in Manufacturing Conference 2021 N2 - This paper presents the laser-based powder bed fusion (L-PBF) using various glass powders (borosilicate and quartz glass). Compared to metals, these require adapted process strategies. First, the glass powders were characterized with regard to their material properties and their processability in the powder bed. This was followed by investigations of the melting behavior of the glass powders with different laser wavelengths (10.6 µm, 1070 nm). In particular, the experimental setup of a CO2 laser was adapted for the processing of glass powder. An experimental setup with integrated coaxial temperature measurement/control and an inductively heatable build platform was created. This allowed the L-PBF process to be carried out at the transformation temperature of the glasses. Furthermore, the component’s material quality was analyzed on three-dimensional test specimen with regard to porosity, roughness, density and geometrical accuracy in order to evaluate the developed L-PBF parameters and to open up possible applications. KW - 3D-printing KW - glass KW - additive manufactureing KW - laser based powder fusion Y1 - 2021 ER - TY - THES A1 - Rittner, Jasper T1 - Wald im Wandel N2 - Die Arbeit „Wald im Wandel“ beschäftigt sich mit dem derzeitigen Zustand des Waldes in Deutschland und seiner kulturhistorischen Bedeutung. Im dazugehörigen Kurzfilm sieht man Aufnahmen der menschlichen Einflussnahme auf den Wald. Diese wurden mit „waldromantischen“ Motiven umgestaltet. Die Kraft „waldromantischer“ Bilder ist so überzeugend, dass hieraus Überlegungen zu einer klimapolitischen Kampagne entstanden sind. Diese sind auf einer Informations-Webpage mit dem Titel „Projekt: Wald im Wandel“ nachzulesen. Die Arbeit schlägt eine Brücke vom kulturhistorischen Symbol „deutscher Wald“ hin zur Gegenwart - und dem Wald in Deutschland als einem potenziellen klimapolitischen Symbol. KW - Wald KW - Borkenkäfer KW - Klimawandel KW - Waldsterben KW - Waldromantik Y1 - 2021 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER - TY - CHAP A1 - Ritschel, Konstantin A1 - Stenzel, Adina A1 - Czarnecki, Christian A1 - Hong, Chin-Gi ED - Gesellschaft für Informatik e.V. (GI), T1 - Realizing robotic process automation potentials: an architectural perspective on a real-life implementation case T2 - GI Edition Proceedings Band 314 "INFORMATIK 2021" Computer Science & Sustainability N2 - The initial idea of Robotic Process Automation (RPA) is the automation of business processes through a simple emulation of user input and output by software robots. Hence, it can be assumed that no changes of the used software systems and existing Enterprise Architecture (EA) is required. In this short, practical paper we discuss this assumption based on a real-life implementation project. We show that a successful RPA implementation might require architectural work during analysis, implementation, and migration. As practical paper we focus on exemplary lessons-learned and new questions related to RPA and EA. KW - Robotic Process Automation KW - Enterprise Architecture KW - Implementation Case Y1 - 2021 SN - 9783885797081 SN - 1617-5468 N1 - INFORMATIK 2021 – 51. Jahrestagung der Gesellschaft für Informatik, 27. September – 01. Oktober 2021 / Virtuell, Berlin. https://informatik2021.gi.de/ SP - 1303 EP - 1311 PB - Köllen CY - Bonn ER - TY - INPR A1 - Ringers, Christa A1 - Bialonski, Stephan A1 - Solovev, Anton A1 - Hansen, Jan N. A1 - Ege, Mert A1 - Friedrich, Benjamin M. A1 - Jurisch-Yaksi, Nathalie T1 - Preprint: Local synchronization of cilia and tissue-scale cilia alignment are sufficient for global metachronal waves T2 - bioRxiv N2 - Motile cilia are hair-like cell extensions present in multiple organs of the body. How cilia coordinate their regular beat in multiciliated epithelia to move fluids remains insufficiently understood, particularly due to lack of rigorous quantification. We combine here experiments, novel analysis tools, and theory to address this knowledge gap. We investigate collective dynamics of cilia in the zebrafish nose, due to its conserved properties with other ciliated tissues and its superior accessibility for non-invasive imaging. We revealed that cilia are synchronized only locally and that the size of local synchronization domains increases with the viscosity of the surrounding medium. Despite the fact that synchronization is local only, we observed global patterns of traveling metachronal waves across the multiciliated epithelium. Intriguingly, these global wave direction patterns are conserved across individual fish, but different for left and right nose, unveiling a chiral asymmetry of metachronal coordination. To understand the implications of synchronization for fluid pumping, we used a computational model of a regular array of cilia. We found that local metachronal synchronization prevents steric collisions and improves fluid pumping in dense cilia carpets, but hardly affects the direction of fluid flow. In conclusion, we show that local synchronization together with tissue-scale cilia alignment are sufficient to generate metachronal wave patterns in multiciliated epithelia, which enhance their physiological function of fluid pumping. Y1 - 2021 U6 - http://dx.doi.org/10.1101/2021.11.23.469646 N1 - Veröffentlicht in eLife 12:e77701 (https://doi.org/10.7554/eLife.77701). ER - TY - JOUR A1 - Richter, Charlotte A1 - Braunstein, Björn A1 - Stäudle, Benjamin A1 - Attias, Julia A1 - Süss, Alexander A1 - Weber, Tobias A1 - Mileva, Katya N. A1 - Rittweger, Jörn A1 - Green, David A. A1 - Albracht, Kirsten T1 - Gastrocnemius medialis contractile behavior during running differs between simulated Lunar and Martian gravities JF - Scientific reports N2 - The international partnership of space agencies has agreed to proceed forward to the Moon sustainably. Activities on the Lunar surface (0.16 g) will allow crewmembers to advance the exploration skills needed when expanding human presence to Mars (0.38 g). Whilst data from actual hypogravity activities are limited to the Apollo missions, simulation studies have indicated that ground reaction forces, mechanical work, muscle activation, and joint angles decrease with declining gravity level. However, these alterations in locomotion biomechanics do not necessarily scale to the gravity level, the reduction in gastrocnemius medialis activation even appears to level off around 0.2 g, while muscle activation pattern remains similar. Thus, it is difficult to predict whether gastrocnemius medialis contractile behavior during running on Moon will basically be the same as on Mars. Therefore, this study investigated lower limb joint kinematics and gastrocnemius medialis behavior during running at 1 g, simulated Martian gravity, and simulated Lunar gravity on the vertical treadmill facility. The results indicate that hypogravity-induced alterations in joint kinematics and contractile behavior still persist between simulated running on the Moon and Mars. This contrasts with the concept of a ceiling effect and should be carefully considered when evaluating exercise prescriptions and the transferability of locomotion practiced in Lunar gravity to Martian gravity. KW - Bone quality and biomechanics KW - Environmental impact KW - Skeletal muscle KW - Tendons KW - Ultrasound Y1 - 2021 U6 - http://dx.doi.org/10.1038/s41598-021-00527-9 SN - 2045-2322 N1 - Corresponding author: Charlotte Richter VL - 11 IS - Article number: 22555 PB - Springer Nature CY - London ER - TY - JOUR A1 - Richter, Charlotte A1 - Braunstein, Bjoern A1 - Stäudle, Benjamin A1 - Attias, Julia A1 - Suess, Alexander A1 - Weber, Tobias A1 - Mileva, Katja N. A1 - Rittweger, Joern A1 - Green, David A. A1 - Albracht, Kirsten T1 - Gastrocnemius medialis contractile behavior is preserved during 30% body weight supported gait training JF - Frontiers in Sports and Active Living N2 - Rehabilitative body weight supported gait training aims at restoring walking function as a key element in activities of daily living. Studies demonstrated reductions in muscle and joint forces, while kinematic gait patterns appear to be preserved with up to 30% weight support. However, the influence of body weight support on muscle architecture, with respect to fascicle and series elastic element behavior is unknown, despite this having potential clinical implications for gait retraining. Eight males (31.9 ± 4.7 years) walked at 75% of the speed at which they typically transition to running, with 0% and 30% body weight support on a lower-body positive pressure treadmill. Gastrocnemius medialis fascicle lengths and pennation angles were measured via ultrasonography. Additionally, joint kinematics were analyzed to determine gastrocnemius medialis muscle–tendon unit lengths, consisting of the muscle's contractile and series elastic elements. Series elastic element length was assessed using a muscle–tendon unit model. Depending on whether data were normally distributed, a paired t-test or Wilcoxon signed rank test was performed to determine if body weight supported walking had any effects on joint kinematics and fascicle–series elastic element behavior. Walking with 30% body weight support had no statistically significant effect on joint kinematics and peak series elastic element length. Furthermore, at the time when peak series elastic element length was achieved, and on average across the entire stance phase, muscle–tendon unit length, fascicle length, pennation angle, and fascicle velocity were unchanged with respect to body weight support. In accordance with unchanged gait kinematics, preservation of fascicle–series elastic element behavior was observed during walking with 30% body weight support, which suggests transferability of gait patterns to subsequent unsupported walking. KW - AlterG KW - rehabilitation KW - gait KW - walking KW - ultrasound imaging KW - series elastic element behavior KW - muscle fascicle behavior KW - unloading Y1 - 2021 U6 - http://dx.doi.org/10.3389/fspor.2020.614559 SN - 2624-9367 VL - 2021 IS - 2 PB - Frontiers CY - Lausanne ER - TY - JOUR A1 - Richter, Charlotte A1 - Braunstein, Bjoern A1 - Staeudle, Benjamin A1 - Attias, Julia A1 - Suess, Alexander A1 - Weber, Tobias A1 - Mileva, Katya N. A1 - Rittweger, Joern A1 - Green, David A. A1 - Albracht, Kirsten T1 - Contractile behavior of the gastrocnemius medialis muscle during running in simulated hypogravity JF - npj Microgravity N2 - Vigorous exercise countermeasures in microgravity can largely attenuate muscular degeneration, albeit the extent of applied loading is key for the extent of muscle wasting. Running on the International Space Station is usually performed with maximum loads of 70% body weight (0.7 g). However, it has not been investigated how the reduced musculoskeletal loading affects muscle and series elastic element dynamics, and thereby force and power generation. Therefore, this study examined the effects of running on the vertical treadmill facility, a ground-based analog, at simulated 0.7 g on gastrocnemius medialis contractile behavior. The results reveal that fascicle−series elastic element behavior differs between simulated hypogravity and 1 g running. Whilst shorter peak series elastic element lengths at simulated 0.7 g appear to be the result of lower muscular and gravitational forces acting on it, increased fascicle lengths and decreased velocities could not be anticipated, but may inform the development of optimized running training in hypogravity. However, whether the alterations in contractile behavior precipitate musculoskeletal degeneration warrants further study. Y1 - 2021 U6 - http://dx.doi.org/10.1038/s41526-021-00155-7 SN - 2373-8065 N1 - Corresponding author: Charlotte Richter VL - 7 IS - Article number: 32 PB - Springer Nature CY - New York ER - TY - THES A1 - Raithel, Luise Marie T1 - Die Wilhelma Stuttgart: Ein neues Erscheinungsbild für den zoologisch-botanischen Garten N2 - Inmitten des Stuttgarter Kessels findet sich Deutschlands einziger zoologisch-botanischer Garten wieder – die Wilhelma. Umrahmt von einer denkmalgeschützten Parkanlage des 19. Jahrhunderts mit maurischen Gebäuden lässt sie Bildung mit Freizeit verschmelzen. Das neue Erscheinungsbild positioniert die schwäbische Einrichtung sowohl als Ort des Zusammenkommens als auch der Erholung und Wissensvermittlung. Bereits vor dem Betreten der Wilhelma soll ihre besondere Charakteristik aufgezeigt und entscheidend von ähnlichen Institutionen distanziert werden. Das grundlegende Gestaltungskonzept rückt die Symbiose aus Zoologie, Botanik und Historie in den Vordergrund. Inspiriert von der maurischen Architektur basiert die Gesamtgestaltung auf feinen geometrischen Formen. Diese bieten Orientierung, unterstreichen die Vielfältigkeit der Wilhelma und vereinen sich darüber hinaus im Logo miteinander. KW - Wilhelma KW - Stuttgart KW - Zoo KW - Botanik KW - Redesign Y1 - 2021 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER - TY - JOUR A1 - Pourshahidi, Ali Mohammad A1 - Achtsnicht, Stefan A1 - Nambipareechee, Mrinal Murali A1 - Offenhäusser, Andreas A1 - Krause, Hans-Joachim T1 - Multiplex detection of magnetic beads using offset field dependent frequency mixing magnetic detection JF - Sensors N2 - Magnetic immunoassays employing Frequency Mixing Magnetic Detection (FMMD) have recently become increasingly popular for quantitative detection of various analytes. Simultaneous analysis of a sample for two or more targets is desirable in order to reduce the sample amount, save consumables, and save time. We show that different types of magnetic beads can be distinguished according to their frequency mixing response to a two-frequency magnetic excitation at different static magnetic offset fields. We recorded the offset field dependent FMMD response of two different particle types at frequencies ƒ₁ + n⋅ƒ₂, n = 1, 2, 3, 4 with ƒ₁ = 30.8 kHz and ƒ₂ = 63 Hz. Their signals were clearly distinguishable by the locations of the extremes and zeros of their responses. Binary mixtures of the two particle types were prepared with different mixing ratios. The mixture samples were analyzed by determining the best linear combination of the two pure constituents that best resembled the measured signals of the mixtures. Using a quadratic programming algorithm, the mixing ratios could be determined with an accuracy of greater than 14%. If each particle type is functionalized with a different antibody, multiplex detection of two different analytes becomes feasible. KW - colorization KW - multiplex detection KW - frequency mixing magnetic detection KW - magnetic nanoparticles Y1 - 2021 U6 - http://dx.doi.org/10.3390/s21175859 SN - 1424-8220 N1 - This article belongs to the Special Issue "Advanced Nanomaterial-Based Sensors for Biomedical Applications" VL - 21 IS - 17 PB - MDPI CY - Basel ER - TY - JOUR A1 - Poghossian, Arshak A1 - Welden, Rene A1 - Buniatyan, Vahe V. A1 - Schöning, Michael Josef T1 - An Array of On-Chip Integrated, Individually Addressable Capacitive Field-Effect Sensors with Control Gate: Design and Modelling JF - Sensors N2 - The on-chip integration of multiple biochemical sensors based on field-effect electrolyte-insulator-semiconductor capacitors (EISCAP) is challenging due to technological difficulties in realization of electrically isolated EISCAPs on the same Si chip. In this work, we present a new simple design for an array of on-chip integrated, individually electrically addressable EISCAPs with an additional control gate (CG-EISCAP). The existence of the CG enables an addressable activation or deactivation of on-chip integrated individual CG-EISCAPs by simple electrical switching the CG of each sensor in various setups, and makes the new design capable for multianalyte detection without cross-talk effects between the sensors in the array. The new designed CG-EISCAP chip was modelled in so-called floating/short-circuited and floating/capacitively-coupled setups, and the corresponding electrical equivalent circuits were developed. In addition, the capacitance-voltage curves of the CG-EISCAP chip in different setups were simulated and compared with that of a single EISCAP sensor. Moreover, the sensitivity of the CG-EISCAP chip to surface potential changes induced by biochemical reactions was simulated and an impact of different parameters, such as gate voltage, insulator thickness and doping concentration in Si, on the sensitivity has been discussed. KW - equivalent circuit KW - multianalyte detection KW - control gate KW - on-chip integrated addressable EISCAP sensors KW - capacitive field-effect sensor Y1 - 2021 U6 - http://dx.doi.org/10.3390/s21186161 SN - 1424-8220 N1 - This article belongs to the Special Issue "Field-Effect Sensors: From pH Sensing to Biosensing" VL - 21 IS - 18 SP - 17 PB - MDPI CY - Basel ER - TY - JOUR A1 - Poghossian, Arshak A1 - Schöning, Michael Josef T1 - Recent progress in silicon-based biologically sensitive field-effect devices JF - Current Opinion in Electrochemistry N2 - Biologically sensitive field-effect devices (BioFEDs) advantageously combine the electronic field-effect functionality with the (bio)chemical receptor’s recognition ability for (bio)chemical sensing. In this review, basic and widely applied device concepts of silicon-based BioFEDs (ion-sensitive field-effect transistor, silicon nanowire transistor, electrolyte-insulator-semiconductor capacitor, light-addressable potentiometric sensor) are presented and recent progress (from 2019 to early 2021) is discussed. One of the main advantages of BioFEDs is the label-free sensing principle enabling to detect a large variety of biomolecules and bioparticles by their intrinsic charge. The review encompasses applications of BioFEDs for the label-free electrical detection of clinically relevant protein biomarkers, deoxyribonucleic acid molecules and viruses, enzyme-substrate reactions as well as recording of the cell acidification rate (as an indicator of cellular metabolism) and the extracellular potential. Y1 - 2021 U6 - http://dx.doi.org/10.1016/j.coelec.2021.100811 SN - 2451-9103 IS - Article number: 100811 PB - Elsevier CY - Amsterdam ER - TY - BOOK A1 - Pieper, Martin T1 - Quantum mechanics: Introduction to mathematical formulation N2 - Anyone who has always wanted to understand the hieroglyphs on Sheldon's blackboard in the TV series The Big Bang Theory or who wanted to know exactly what the fate of Schrödinger's cat is all about will find a short, descriptive introduction to the world of quantum mechanics in this essential. The text particularly focuses on the mathematical description in the Hilbert space. The content goes beyond popular scientific presentations, but is nevertheless suitable for readers without special prior knowledge thanks to the clear examples. KW - Quantenmechanik KW - Hilbert Room KW - Postulates KW - Schrödingers cat KW - Operators Y1 - 2021 SN - 978-3-658-32644-9 SN - 978-3-658-32645-6 U6 - http://dx.doi.org/10.1007/978-3-658-32645-6 PB - Springer CY - Wiesbaden ER - TY - CHAP A1 - Pfetsch, Marc E. A1 - Abele, Eberhard A1 - Altherr, Lena A1 - Bölling, Christian A1 - Brötz, Nicolas A1 - Dietrich, Ingo A1 - Gally, Tristan A1 - Geßner, Felix A1 - Groche, Peter A1 - Hoppe, Florian A1 - Kirchner, Eckhard A1 - Kloberdanz, Hermann A1 - Knoll, Maximilian A1 - Kolvenbach, Philip A1 - Kuttich-Meinlschmidt, Anja A1 - Leise, Philipp A1 - Lorenz, Ulf A1 - Matei, Alexander A1 - Molitor, Dirk A. A1 - Niessen, Pia A1 - Pelz, Peter F. A1 - Rexer, Manuel A1 - Schmitt, Andreas A1 - Schmitt, Johann M. A1 - Schulte, Fiona A1 - Ulbrich, Stefan A1 - Weigold, Matthias T1 - Strategies for mastering uncertainty T2 - Mastering uncertainty in mechanical engineering N2 - This chapter describes three general strategies to master uncertainty in technical systems: robustness, flexibility and resilience. It builds on the previous chapters about methods to analyse and identify uncertainty and may rely on the availability of technologies for particular systems, such as active components. Robustness aims for the design of technical systems that are insensitive to anticipated uncertainties. Flexibility increases the ability of a system to work under different situations. Resilience extends this characteristic by requiring a given minimal functional performance, even after disturbances or failure of system components, and it may incorporate recovery. The three strategies are described and discussed in turn. Moreover, they are demonstrated on specific technical systems. Y1 - 2021 SN - 978-3-030-78353-2 U6 - http://dx.doi.org/10.1007/978-3-030-78354-9_6 N1 - Part of the Springer Tracts in Mechanical Engineering book series (STME) SP - 365 EP - 456 PB - Springer CY - Cham ER - TY - CHAP A1 - Pfeiffer, Johann A1 - Balc, N. A1 - Gebhardt, Andreas T1 - Studie zur Untersuchung der Auswirkung von Fräsbahnstrategien auf die Oberflächenqualität von mittels SLM gefertigten Metallteilen T2 - Tagungsband 21. Nachwuchswissenschaftler*innenkonferenz N2 - Für die Herstellung von metallischen Bauteilen wird in der heutigen Zeit eine Vielzahl von Verfahren auf dem Markt angeboten. Dabei stehen die additiven im Wettbewerb zu den konventionellen Verfahren. Die erreichbaren Oberflächenqualitäten der additiven sind nicht mit denen spanender Verfahren vergleichbar. Für diesen Beitrag wurde analysiert, ob sich ein mittels Selektivem Laserschmelzen (SLM) additiv hergestellter Edelstahl hinsichtlich seiner Oberflächenqualität nach der Zerspanung von einem umgeformten konventionell hergestellten Edelstahl gleicher Sorte unterscheidet. Y1 - 2021 SN - 978-3-932886-36-2 N1 - 21. Nachwuchswissenschaftler*innenkonferenz, Ernst-Abbe-Hochschule Jena 26. und 27. Mai 2021 SP - 99 EP - 102 PB - Verlag Ernst-Abbe-Hochschule Jena CY - Jena ER - TY - CHAP A1 - Peterson, Leif Arne ED - Schlüter, Dominik T1 - Holzbau T2 - Wofür braucht man das eigentlich? Ein Handbuch für Mathematiklehrkräfte der Sekundarstufe I und II Y1 - 2021 SN - 978-3-7543-2606-0 SP - 21 EP - 23 PB - BoD CY - Norderstedt ER - TY - THES A1 - Paulzen, Lena T1 - Nachhaltiges Corporate Packaging Design: Am Beispiel von Naturkosmetik Produkten. N2 - Diese Bachelorarbeit widmet sich dem nachhaltigen Packaging-Design von Kosmetikprodukten. Dies wird am Beispiel eines Naturkosmetik-Unternehmens dargestellt. Die Gestaltung einer Shampoo-Flasche wird in dem vorliegenden Projekt exemplarisch für die thematische und gestalterische Untersuchung genutzt. Zudem wurden mit Tube und Tiegel noch zwei weitere Verpackungsformen erstellt. Das Ziel dieser Arbeit ist es, eine nachhaltige Verpackung zu gestalten. Diese soll den hohen CO2-Ausstoß bei der Herstellung von Verpackungen verringern und dabei dem Anspruch des Marketings gerecht werden. Hierbei wurde ein Logo-Design, ein Farbkonzept, eine einheitliche Formsprache und eine Typografie erarbeitet. KW - Corporate Design KW - nachhaltig KW - Packaging Design KW - Naturkosmetik KW - Shampooflasche Y1 - 2021 PB - FH Aachen CY - Aachen ER - TY - THES A1 - Ossenkop, Birte T1 - Prepare to care: Kampagne für mehr Unterstützung und Wertschätzung von Young Carern durch ihr direktes Lebensumfeld N2 - In jeder Schulklasse in Deutschland gibt es laut Statistik einen bis zwei Young Carer. Das sind Kinder und Jugendliche, die ein Familienmitglied pflegen. Doch wegen Unverständnis und Ausgrenzung seitens ihres sozialen Umfeldes vertrauen sich Young Carer niemandem an. Es mangelt schlichtweg an öffentlichem Bewusstsein für das Phänomen. Die Kampagne #nichtbloßjung soll das ändern. Sie zeigt einer jungen Zielgruppe, was es bedeutet, nicht bloß jung, sondern Young Carer zu sein. Dabei regt sie dazu an, ebenfalls #nichtbloßjung zu bleiben, sondern als „Young Supporter“ die Young Carer zu unterstützen. Dazu wird diverse Informationsmaterial sowie ein kostenloses Armband bereitgestellt. Die Armbandtragenden zeigen so, dass sie Young Carer unterstützen und als Ansprechpersonen zur Verfügung stehen. So lernen Young Carer, dass sie mit ihrer Situation nicht allein sind und an wen sie sich gegebenenfalls wenden können. KW - Young Carer KW - Kampagne KW - Kinder KW - Sensibilisierung KW - Aufklärung Y1 - 2021 PB - FH Aachen CY - Aachen ER - TY - JOUR A1 - Oliveira, Danilo A. A1 - Molinnus, Denise A1 - Beging, Stefan A1 - Siqueira Jr, José R. A1 - Schöning, Michael Josef T1 - Biosensor Based on Self-Assembled Films of Graphene Oxide and Polyaniline Using a Field-Effect Device Platform JF - physica status solidi (a) applications and materials science N2 - A new functionalization method to modify capacitive electrolyte–insulator–semiconductor (EIS) structures with nanofilms is presented. Layers of polyallylamine hydrochloride (PAH) and graphene oxide (GO) with the compound polyaniline:poly(2-acrylamido-2-methyl-1-propanesulfonic acid) (PANI:PAAMPSA) are deposited onto a p-Si/SiO2 chip using the layer-by-layer technique (LbL). Two different enzymes (urease and penicillinase) are separately immobilized on top of a five-bilayer stack of the PAH:GO/PANI:PAAMPSA-modified EIS chip, forming a biosensor for detection of urea and penicillin, respectively. Electrochemical characterization is performed by constant capacitance (ConCap) measurements, and the film morphology is characterized by atomic force microscopy (AFM) and scanning electron microscopy (SEM). An increase in the average sensitivity of the modified biosensors (EIS–nanofilm–enzyme) of around 15% is found in relation to sensors, only carrying the enzyme but without the nanofilm (EIS–enzyme). In this sense, the nanofilm acts as a stable bioreceptor onto the EIS chip improving the output signal in terms of sensitivity and stability. KW - capacitive electrolyte–insulator–semiconductor sensors KW - graphene oxide KW - layer-by-layer technique KW - nanomaterials KW - polyaniline Y1 - 2021 U6 - http://dx.doi.org/10.1002/pssa.202000747 SN - 1862-6319 N1 - Corresponding author: José R. Siqueira Jr & Michael J. Schöning VL - 218 IS - 13 SP - 1 EP - 9 PB - Wiley-VCH CY - Weinheim ER - TY - CHAP A1 - Olderog, M. A1 - Mohr, P. A1 - Beging, Stefan A1 - Tsoumpas, C. A1 - Ziemons, Karl T1 - Simulation study on the role of tissue-scattered events in improving sensitivity for a compact time of flight compton positron emission tomograph T2 - 2020 IEEE Nuclear Science Symposium and Medical Imaging Conference (NSS/MIC) N2 - In positron emission tomography improving time, energy and spatial detector resolutions and using Compton kinematics introduces the possibility to reconstruct a radioactivity distribution image from scatter coincidences, thereby enhancing image quality. The number of single scattered coincidences alone is in the same order of magnitude as true coincidences. In this work, a compact Compton camera module based on monolithic scintillation material is investigated as a detector ring module. The detector interactions are simulated with Monte Carlo package GATE. The scattering angle inside the tissue is derived from the energy of the scattered photon, which results in a set of possible scattering trajectories or broken line of response. The Compton kinematics collimation reduces the number of solutions. Additionally, the time of flight information helps localize the position of the annihilation. One of the questions of this investigation is related to how the energy, spatial and temporal resolutions help confine the possible annihilation volume. A comparison of currently technically feasible detector resolutions (under laboratory conditions) demonstrates the influence on this annihilation volume and shows that energy and coincidence time resolution have a significant impact. An enhancement of the latter from 400 ps to 100 ps leads to a smaller annihilation volume of around 50%, while a change of the energy resolution in the absorber layer from 12% to 4.5% results in a reduction of 60%. The inclusion of single tissue-scattered data has the potential to increase the sensitivity of a scanner by a factor of 2 to 3 times. The concept can be further optimized and extended for multiple scatter coincidences and subsequently validated by a reconstruction algorithm. Y1 - 2021 SN - 978-1-7281-7693-2 U6 - http://dx.doi.org/10.1109/NSS/MIC42677.2020.9507901 N1 - 2020 IEEE Nuclear Science Symposium and Medical Imaging Conference (NSS/MIC), 31 Oct.-7 Nov. 2020, Boston, MA, USA PB - IEEE ER - TY - JOUR A1 - Olbertz, Klaus T1 - Die Dienstreisezeit als Arbeitszeit – oder doch nicht? : Zur arbeitgeberfreundlichen Bewertung von Dienstreisezeiten durch das Bundesarbeitsgericht JF - NWB - Steuer- und Wirtschaftsrecht N2 - Der arbeitsrechtlich richtige Umgang mit Zeiten einer Dienstreise kann in der betrieblichen Praxis Probleme bereiten. Ob die Reisezeiten als solche Arbeitszeit i. S. des Arbeitszeitgesetzes (ArbZG ) darstellen, also bspw. auf die tägliche Höchstarbeitszeit angerechnet werden müssen oder nicht, ist oftmals genauso unklar wie die Frage, ob und inwieweit Reisezeiten vergütungspflichtig sind. Aber auch, ob ein Arbeitnehmer überhaupt zur Durchführung einer Dienstreise verpflichtet werden kann, ist ein möglicher Anlass von Streitigkeiten zwischen den Arbeitsvertragsparteien, wie verschiedene Gerichtsentscheidungen zeigen. Der nachfolgende Beitrag beantwortet die aufgeworfenen Fragen und gibt hierzu einen praxisorientierten Überblick. Y1 - 2021 SN - 0028-3460 IS - 1 SP - 38 EP - 44 ER - TY - JOUR A1 - Olbertz, Klaus T1 - Wichtige arbeitsrechtliche Entwicklungen im Jahr 2020 : Der Jahresrückblick auf alles Wissenswerte im Arbeitsrecht des vergangenen Jahres JF - NWB - Steuer- und Wirtschaftsrecht N2 - Im Anschluss an die arbeitsrechtlichen Jahresübersichten der vergangenen Jahre (NWB 5/2019 S. 266; NWB 8/2020 S. 557) gibt der nachfolgende Beitrag einen Überblick über relevante Entwicklungen im Arbeitsrecht des Jahres 2020. Der erste Teil beschäftigt sich hierbei mit gesetzlichen Änderungen. Neben Regelungen, die auf die COVID-19-Pandemie zurückgeführt werden können, hat der Gesetzgeber auch andere Vorhaben umgesetzt. So wurde u. a. das Arbeitnehmerentsenderecht reformiert. Für Diskussionen sorgt(e) zudem das Gesetzesvorhaben zur Regelung mobiler Arbeit. Im zweiten Teil werden für die Praxis wichtige höchstrichterliche Gerichtsentscheidungen zum Arbeitsrecht erläutert, alphabetisch sortiert von A (wie Antidiskriminierungsrecht) bis U (wie Urlaub). Y1 - 2021 SN - 0028-3460 IS - 10 SP - 703 EP - 715 ER - TY - JOUR A1 - Olbertz, Klaus T1 - Die Flexibilisierung von Arbeitszeit durch den Abruf von Arbeit : Möglichkeiten und Grenzen arbeitsvertraglicher Gestaltung zur Vermeidung von „Leerlaufzeiten“ JF - NWB - Steuer- und Wirtschaftsrecht N2 - Die Arbeitswelt ist im Umbruch. Der Bedarf an flexiblen Arbeitszeitmodellen nimmt stetig zu, wobei die Corona-Pandemie dieses Bedürfnis nochmals verschärft hat. Gerade auch in kleineren und mittleren Unternehmen wächst die Notwendigkeit, den Einsatz der Beschäftigten möglichst bedarfsgerecht zu steuern, also bei guter Auftragslage mehr Arbeitszeit abzurufen und bei ausbleibenden Aufträgen die Arbeitszeit zu reduzieren und somit bezahlte „Leerlaufzeiten“ zu vermeiden. Der Gesetzgeber stellt den Arbeitgebern hierfür das Instrument der sog. Abrufarbeit ( § 12 Teilzeit- und Befristungsgesetz – TzBfG ) zur Verfügung. In dem nachfolgenden Beitrag werden Möglichkeiten und Grenzen der Abrufarbeit skizziert und konkrete arbeitsvertragliche Gestaltungsmöglichkeiten aufgezeigt. Y1 - 2021 SN - 0028-3460 IS - 15 SP - 1055 EP - 1063 ER - TY - JOUR A1 - Olbertz, Klaus T1 - Vertragsgestaltungen bei der Beschäftigung von Rentnern in Unternehmen : (Befristete) Beschäftigungsverhältnisse als sinnvolles Instrument zum Schließen von Personallücken JF - NWB - Steuer- und Wirtschaftsrecht Y1 - 2021 SN - 0028-3460 IS - 25 SP - 1810 EP - 1817 ER - TY - CHAP A1 - Nikolovski, Gjorgji A1 - Reke, Michael A1 - Elsen, Ingo A1 - Schiffer, Stefan T1 - Machine learning based 3D object detection for navigation in unstructured environments T2 - 2021 IEEE Intelligent Vehicles Symposium Workshops (IV Workshops) N2 - In this paper we investigate the use of deep neural networks for 3D object detection in uncommon, unstructured environments such as in an open-pit mine. While neural nets are frequently used for object detection in regular autonomous driving applications, more unusual driving scenarios aside street traffic pose additional challenges. For one, the collection of appropriate data sets to train the networks is an issue. For another, testing the performance of trained networks often requires tailored integration with the particular domain as well. While there exist different solutions for these problems in regular autonomous driving, there are only very few approaches that work for special domains just as well. We address both the challenges above in this work. First, we discuss two possible ways of acquiring data for training and evaluation. That is, we evaluate a semi-automated annotation of recorded LIDAR data and we examine synthetic data generation. Using these datasets we train and test different deep neural network for the task of object detection. Second, we propose a possible integration of a ROS2 detector module for an autonomous driving platform. Finally, we present the performance of three state-of-the-art deep neural networks in the domain of 3D object detection on a synthetic dataset and a smaller one containing a characteristic object from an open-pit mine. KW - 3D object detection KW - LiDAR KW - autonomous driving KW - Deep learning KW - Three-dimensional displays Y1 - 2021 SN - 978-1-6654-7921-9 U6 - http://dx.doi.org/10.1109/IVWorkshops54471.2021.9669218 N1 - 2021 IEEE Intelligent Vehicles Symposium Workshops (IV Workshops), 11-17 July 2021, Nagoya, Japan. SP - 236 EP - 242 PB - IEEE ER - TY - THES A1 - Niederschmidt, Sören T1 - Living product: ein Ansatz, lebendige Organismen mit einem Produkt zu vereinen und nutzbar zu machen N2 - Diese Arbeit setzt sich mit der Frage auseinander, in welcher Form sich lebendige Organismen – hier insbesondere Pilze - in die Produktwelt integrieren lassen. In welcher Art und Weise beeinflusst ein Organismus das Produkterlebnis? Im Rahmen dieser Arbeit sind vier verschiedene Produkte entstanden, die die Stärken des Materials Myzelium demonstrieren. Myzelium bezeichnet das sehr dichte Wurzelnetzwerk eines Pilzes. Dieses lebendige Netzwerk kann dazu genutzt werden, um organische Stoffe miteinander zu verwachsen und somit Formen entstehen zu lassen. Die so entstandenen Produkte sind in eine Konzeptumgebung eingebettet, in der der Verbrauchende die Natur durch naturnähere Produkte (Form, Material und gewachsene Strukturen) neu erlebt. Gezeigt wird ein Packaging für Einmachgläser, ein Kressebeet, ein Wandregal und ein Teelicht. KW - Myzelium KW - biofabrication KW - biodesign KW - fungalmaterials KW - Bioluminszenz Y1 - 2021 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER - TY - THES A1 - Niedermeier, Jacqueline T1 - Aachener Tierpark Euregiozoo: Corporate Design für eine Institution mit Bildungsauftrag N2 - Der Aachener Tierpark Euregiozoo lässt die Aspekte "Bildung" und "Forschung" mit "Erholung" und "Erhaltung" an einem Ort miteinander verschmelzen. Auf einer Fläche von rund 8,9 ha beherbergt der Zoo etwa 1.000 Tiere aus 200 verschiedenen Arten und Rassen in großzügigen und natürlich gestalteten Gehegen. Das neue Designkonzept soll den Bildungsaspekt in den Vordergrund rücken und modernisieren. Der Einsatz verschiedenster Medien soll die breite Zielgruppe von Jung bis Alt ansprechen und das Interesse nach neuem Wissen anregen. Das neue Leitsystem sorgt nicht nur für Orientierung im Park, es ermöglicht auch interaktive und individuelle Führungen durch den Zoo. Kombiniert mit einem Wissensquiz und zahlreichen spannenden Fakten über die Tierwelt des Parks wird der Zoobesuch zu einem ganz besonderen Erlebnis. KW - Corporate Design KW - Interaktives Design KW - Zoologischer Garten KW - Tierpark KW - Euregiozoo Y1 - 2021 PB - FH Aachen CY - Aachen ER - TY - CHAP A1 - Neumann, Hannah A1 - Adam, Mario A1 - Backes, Klaus A1 - Börner, Martin A1 - Clees, Tanja A1 - Doetsch, Christian A1 - Glaeser, Susanne A1 - Herrmann, Ulf A1 - May, Johanna A1 - Rosenthal, Florian A1 - Sauer, Dirk Uwe A1 - Stadler, Ingo T1 - Development of open educational resources for renewable energy and the energy transition process T2 - ISES SWC 2021 N2 - The dissemination of knowledge about renewable energies is understood as a social task with the highest topicality. The transfer of teaching content on renewable energies into digital open educational resources offers the opportunity to significantly accelerate the implementation of the energy transition. Thus, in the here presented project six German universities create open educational resources for the energy transition. These materials are available to the public on the internet under a free license. So far there has been no publicly accessible, editable media that cover entire learning units about renewable energies extensively and in high technical quality. Thus, in this project, the content that remains up-to-date for a longer period is appropriately prepared in terms of media didactics. The materials enable lecturers to provide students with in-depth training about technologies for the energy transition. In a particular way, the created material is also suitable for making the general public knowledgeable about the energy transition with scientifically based material. KW - energy transition KW - renewable energies KW - open educational resources KW - dissemination KW - digitalization Y1 - 2021 U6 - http://dx.doi.org/10.18086/swc.2021.47.03 N1 - ISES Solar World Congress, virtual conference 25-29 October 2021 PB - International Solar Energy Society CY - Freiburg ER - TY - JOUR A1 - Neumaier, Felix A1 - Weiss, Miriam A1 - Veldeman, Michael A1 - Kotliar, Konstantin A1 - Wiesmann, Martin A1 - Schulze-Steinen, Henna A1 - Höllig, Anke A1 - Clusmann, Hans A1 - Schubert, Gerrit Alexander A1 - Albanna, Walid T1 - Changes in endogenous daytime melatonin levels after aneurysmal subarachnoid hemorrhage – preliminary findings from an observational cohort study JF - Clinical Neurology and Neurosurgery N2 - Aneurysmal subarachnoid hemorrhage (aSAH) is associated with early and delayed brain injury due to several underlying and interrelated processes, which include inflammation, oxidative stress, endothelial, and neuronal apoptosis. Treatment with melatonin, a cytoprotective neurohormone with anti-inflammatory, anti-oxidant and anti-apoptotic effects, has been shown to attenuate early brain injury (EBI) and to prevent delayed cerebral vasospasm in experimental aSAH models. Less is known about the role of endogenous melatonin for aSAH outcome and how its production is altered by the pathophysiological cascades initiated during EBI. In the present observational study, we analyzed changes in melatonin levels during the first three weeks after aSAH. KW - constructive alignment KW - examination KW - long-term retention KW - multimodal KW - practical learning Y1 - 2021 U6 - http://dx.doi.org/10.1016/j.clineuro.2021.106870 SN - 0303-8467 VL - 208 IS - Article No.: 106870 PB - Elsevier CY - Amsterdam ER - TY - JOUR A1 - Neumaier, Felix A1 - Kotliar, Konstantin A1 - Haeren, Roel Hubert Louis A1 - Temel, Yasin A1 - Lüke, Jan Niklas A1 - Seyam, Osama A1 - Lindauer, Ute A1 - Clusmann, Hans A1 - Hescheler, Jürgen A1 - Schubert, Gerrit Alexander A1 - Schneider, Toni A1 - Albanna, Walid T1 - Retinal Vessel Responses to Flicker Stimulation Are Impaired in Ca v 2.3-Deficient Mice—An in- vivo Evaluation Using Retinal Vessel Analysis (RVA) JF - Frontiers in Neurology Y1 - 2021 U6 - http://dx.doi.org/10.3389/fneur.2021.659890 VL - 12 SP - 1 EP - 11 PB - Frontiers ER - TY - THES A1 - Najarov, Azer T1 - Ich sehe was, was Du nicht siehst: Herkunft & Identität jüdischer Menschen in Deutschland nach der Nachkriegszeit N2 - Wir alle haben schon einmal von ihnen gehört. Die einen kennen sie aus dem Geschichtsunterricht, die anderen haben sie vielleicht auch schon mal bewusst oder unbewusst auf der Straße gesehen. Einige sind es sogar selbst. Die Rede ist von jüdischen Menschen in Deutschland. In unserer Bundesrepublik wird die jüdische Bevölkerung unausweichlich mit dem Gedanken des Holocausts verbunden. Jüdinnen und Juden wird somit eine Identität zugesprochen, mit der sie nichts zu tun haben. Es findet eine Stigmatisierung statt. Dabei sind jüdische Menschen heutzutage so divers wie noch nie. Das Printmedium »Ich sehe was, was Du nicht siehst« beleuchtet diese selten wahrgenommene Diversität und zeigt durch spannende Interviews eine jüdische Welt, die außerhalb der NS-Verbrechen liegt. Darüber hinaus findet man Informationen zu verschiedenen jüdischen Bräuchen, historischen Ereignissen und interessanten Infografiken.  KW - Juden KW - Tora KW - Israel KW - Davidstern KW - Holocaust Y1 - 2021 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER - TY - THES A1 - Nahrstedt, Sarah T1 - Any Cargo: Das Fahrrad als Hauptverkehrsmittel in der Stadt N2 - Durch die Urbanisierung, wird es in Städten immer enger und der Verkehr nimmt zu. Das hat hohe Emissionen und Platzmangel zur Folge. In der Masterarbeit wurde die Abhängigkeit zum Auto in der Stadt hinterfragt und ein Konzept erarbeitet, welches die Autonutzung und den Autobesitz ablöst. Dabei entstand ein neuer Fahrradanhänger, der eine multifunktionale Nutzung zulässt und einen elektrischen Antrieb besitzt. Dadurch bietet er einen komfortablen Support im Alltag. Zudem wurde ein Geschäftskonzept entwickelt, welches ermöglicht, den Anhänger mit einem digitalen Ausleihsystem unter Nachbarn oder Freunden zu teilen. Ein wichtiges Kriterium für das Produkt und den Service war, dass die Mobilität der Zukunft nicht nur nachhaltig sein soll, sondern auch Laune machen muss. KW - Mobilität KW - Nachhaltigkeit KW - E-Mobility KW - Transport KW - E-Bike Y1 - 2021 PB - FH Aachen CY - Aachen ER - TY - CHAP A1 - Müller, Tim M. A1 - Schmitt, Andreas A1 - Leise, Philipp A1 - Meck, Tobias A1 - Altherr, Lena A1 - Pelz, Peter F. A1 - Pfetsch, Marc E. T1 - Validation of an optimized resilient water supply system T2 - Uncertainty in Mechanical Engineering N2 - Component failures within water supply systems can lead to significant performance losses. One way to address these losses is the explicit anticipation of failures within the design process. We consider a water supply system for high-rise buildings, where pump failures are the most likely failure scenarios. We explicitly consider these failures within an early design stage which leads to a more resilient system, i.e., a system which is able to operate under a predefined number of arbitrary pump failures. We use a mathematical optimization approach to compute such a resilient design. This is based on a multi-stage model for topology optimization, which can be described by a system of nonlinear inequalities and integrality constraints. Such a model has to be both computationally tractable and to represent the real-world system accurately. We therefore validate the algorithmic solutions using experiments on a scaled test rig for high-rise buildings. The test rig allows for an arbitrary connection of pumps to reproduce scaled versions of booster station designs for high-rise buildings. We experimentally verify the applicability of the presented optimization model and that the proposed resilience properties are also fulfilled in real systems. KW - Optimization KW - Mixed-integer nonlinear programming KW - Water distribution system KW - Resilience KW - Validation Y1 - 2021 SN - 978-3-030-77255-0 SN - 978-3-030-77256-7 U6 - http://dx.doi.org/10.1007/978-3-030-77256-7_7 N1 - Proceedings of the 4th International Conference on Uncertainty in Mechanical Engineering (ICUME 2021), June 7–8, 2021 SP - 70 EP - 80 PB - Springer CY - Cham ER - TY - THES A1 - Müller, Elona T1 - Aus den Augen aus dem Sinn?: Ein Bookazine deckt das Problem des Unsichtbaren Mülls auf N2 - Müll ist immer und überall vorhanden – auch wenn wir ihn nicht sehen. Gerade unsichtbarer Müll birgt für den Menschen und seine Umwelt erhebliche Gefahren, die durch seine Unsichtbarkeit irrelevant erscheinen. Die Publikation mit dem Titel mikromakro deckt durch verschiedene Artikel, Interviews und Texte die Gefahren auf, die durch den unsichtbaren Müll entstehen. Ziel war es, eine Bookazine-Reihe zu konzipieren, die in sechs Ausgaben das Thema des unsichtbaren Mülls beleuchtet. Die erste Ausgabe zum Thema Kunststoff wurde exemplarisch gestaltet. Zusätzlich zum redaktionellen Teil untermauern Infografiken die Texte faktisch und Fotoserien emotional. Da unsichtbarer Müll auf zwei Ebenen zu finden ist – der Makro- (groß) und Mikroebene (klein) – wurde die Publikation inhaltlich zweigeteilt, sodass sich das Layout und die Fotoserien vom Mikro- und Makroteil unterscheiden.  KW - Bookazine KW - Publikation KW - Editorialdesign KW - Magazingestaltung KW - Umweltschutz Y1 - 2021 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER - TY - THES A1 - Mühl, Leonie T1 - Neues Erscheinungsbild für den APX: Redesign des LVR - Archäologischen Park Xanten und des Römermuseums N2 - Der Archäologische Park Xanten (APX) gilt als Deutschlands einziger archäologischer Freiluftpark. Er zeichnet sich im Verbund mit dem Römermuseum durch seine Lage auf dem historischen Grund einer römischen Metropole und seine kontinuierliche Forschungsaktivität aus und bietet so ein einzigartiges Umfeld von kultureller Relevanz. Ziel dieses Projektes war es, ein neues Erscheinungsbild zu entwickeln, welches klar die Thematik des Parks in den Medien erkennbar macht. Das Corporate Design dient dazu, die Inhalte des Verbundes in einem einheitlichen System medienübergreifend zu präsentieren. Das Design unterstützt den APX in seiner Funktion als Begegnungs- und Bildungsstätte. Aufgrund dessen ist es im Hinblick auf das Ziel relevant, das Interesse an Kulturgeschichte und Forschung zu wecken. KW - Redesign KW - Corporate Design KW - Archäologie KW - Museumsidendität KW - Branding Y1 - 2021 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER - TY - THES A1 - Mros, Christina T1 - Entwicklung eines Erscheinungsbildes sowie einer Kampagne für die Allianz Chronischer Seltener Erkrankungen N2 - Die Allianz Chronischer Seltener Erkrankungen (ACHSE) ist das einzige krankheitsübergreifende Netzwerk von und für Menschen mit einer seltenen Erkrankung in Deutschland. Insgesamt sind 4 Millionen Menschen in Deutschland von einer der rund 8.000 seltenen Krankheiten betroffen. Durch die Seltenheit der verschiedenen Krankheiten ist es oft schwer, Experten zu finden, die richtige Versorgung sicherzustellen oder Studien durchzuführen. Betroffene fühlen sich oft nicht wahrgenommen und alleine gelassen. Die ACHSE dient als unabhängige Schnittstelle und Knotenpunkt zwischen Betroffenen, Regierung, Politik und Wirtschaft. Gemeinsam bündeln sich hier 130 Patientenorganisationen unter einem Dach, um die Betroffenen in den Fokus zu rücken. Ziel der Bachelorarbeit ist die Entwicklung eines Erscheinungsbildes sowie einer Kampagne, die das Thema mehr ins Bewusstsein der Öffentlichkeit bringt und informiert. KW - Pro bono KW - Corporate Design KW - Redesign KW - Rare Diseases KW - Seltene Erkrankungen Y1 - 2021 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER - TY - JOUR A1 - Monti, Elena A1 - Waldvogel, Janice A1 - Ritzmann, Ramona A1 - Freyler, Kathrin A1 - Albracht, Kirsten A1 - Helm, Michael A1 - De Cesare, Niccolò A1 - Pavan, Piero A1 - Reggiani, Carlo A1 - Gollhofer, Albert A1 - Narici, Marco Vincenzo T1 - Muscle in variable gravity: “I do not know where I am, but I know what to do” JF - Frontiers in Physiology N2 - Performing tasks, such as running and jumping, requires activation of the agonist and antagonist muscles before (motor unit pre-activation) and during movement performance (Santello and Mcdonagh, 1998). A well-timed and regulated muscle activation elicits a stretch-shortening cycle (SSC) response, naturally occurring in bouncing movements (Ishikawa and Komi, 2004; Taube et al., 2012). By definition, the SSC describes the stretching of a pre-activated muscle-tendon complex immediately followed by a muscle shortening in the concentric push-off phase (Komi, 1984). Given the importance of SSC actions for human movement, it is not surprising that many studies investigated the biomechanics of this phenomenon; in particular, drop jumps (DJs) represent a good paradigm to study muscle fascicle and tendon behavior in ballistic movements involving the SSC. Within a DJ, three main phases [pre-activation, braking, and push-off (PO; Komi, 2000)] have been recognized and extensively studied in common and challenging conditions, such as changes in load, falling height, or simulated hypo-gravity (Avela et al., 1994; Arampatzis et al., 2001; Fukashiro et al., 2005; Ishikawa et al., 2005; Sousa et al., 2007; Ritzmann et al., 2016; Helm et al., 2020). These studies show that the timing and amount of triceps-surae muscle-tendon unit pre-activation in DJs are differentially regulated based on the load applied to the muscle, being optimal in normal “Earth” gravity conditions (Avela et al., 1994), but decreased in simulated hypo-gravity, hyper-gravity (Avela et al., 1994; Ritzmann et al., 2016), or unknown conditions (i.e., unknown falling heights; Helm et al., 2020). Some authors indicated that, when falling from heights different from the optimal one [defined as the drop height giving a maximum DJ performance indicated as peak ground reaction force (GRF) or jump high], electromyographic (EMG) activity of the plantar flexors increases from lower than optimal to higher than optimal heights (Ishikawa and Komi, 2004; Sousa et al., 2007). These findings highlight the ability of the central nervous system to regulate the timing and amount of pre-activation according to different jumping conditions, thus regulating muscle fascicle length, tendon and joint stiffness as well as position, in order to safely land on the ground and quickly re-bounce. Similarly, to pre-activation, also in the braking phase, the plantar flexors are differentially regulated. In optimal height (i.e., load) jumping conditions, gastrocnemius medialis (GM) fascicles shorten at early ground contact (possibly due to the intervention of the stretch reflex; Gollhofer et al., 1992) and behave quasi-isometrically in the late braking phase, enabling tendon elongation, and storage of elastic energy (Gollhofer et al., 1992; Fukashiro et al., 2005; Sousa et al., 2007). When increasing the falling height (augmenting the impact GRF), the quasi-isometric behavior of fascicles disappears, and fast fascicle lengthening occurs (Ishikawa et al., 2005; Sousa et al., 2007). In the third and last PO phase, fascicles shorten and the tendon releases the elastic energy previously stored. Bobbert et al. (1987) reported no influence of jumping height on the work done and on the net vertical impulse assessed during PO; this observation suggests that, despite an optimal DJ performance might be achieved only in specific conditions (falling heights, loads), the central nervous system seems to be able to regulate muscle behavior in order to effectively perform the required task also in challenging situations. Although the regulation of triceps-surae muscle-tendon unit in DJs has been extensively investigated, very few studies focused on sarcomeres behavior during the performance of this SSC movement (Kurokawa et al., 2003; Fukashiro et al., 2005, 2006). Sarcomeres represent muscle contractile units and are known to express different amounts of force depending on their length (Gordon et al., 1966; Walker and Schrodt, 1974); thus, understanding the time course of their responses during DJs is fundamental to gain further insights into muscle force-generating capacity. In vivo measurement of sarcomere length in humans has been so far been performed only in static positions and under highly controlled experimental conditions (Llewellyn et al., 2008; Sanchez et al., 2015). Instead, human sarcomere length estimation (achieved by dividing GM measured fascicle length for a fixed sarcomere number) in dynamic contractions provided an indirect measure of sarcomere operating range during squat jump, countermovement jump, and DJ (Fukashiro et al., 2005, 2006; Kurokawa et al., 2003). The results of these studies showed that sarcomeres operate in the ascending limb of their length-tension (L-T) relationship in all types of jumps, and particularly so in DJ. However, most of the available observations on sarcomere and muscle fascicle behavior were made in condition of constant gravity. Thus, in order to understand how sarcomere and muscle fascicle length are regulated in variable gravity conditions, we performed experiments in a parabolic flight, involving variable gravity levels, ranging from about zero-g to about double the Earth’s gravity (1 g; Waldvogel et al., 2021). Specifically, the aims of the present study were as follows: 1. To investigate the ability of the neuromuscular system in regulating fascicle length in response to conditions of variable gravity. 2. To estimate sarcomere operative length in the different DJ phases, in order to calculate its theoretical force production and its possible modulation in conditions of variable gravity. We hypothesized that muscle fascicles would be differentially regulated in different gravity conditions compared to 1 g, particularly in anticipation of landing and re-bouncing in unknown gravity levels. In addition, we hypothesized that sarcomeres would operate in the upper part of the ascending limb of their L-T relationship, possibly lengthening during the braking phase (especially in hyper-gravity) while operating quasi-isometrically in 1 g. KW - parabolic flight KW - drop jump KW - hypo-gravity KW - hyper-gravity KW - sarcomere operating length Y1 - 2021 U6 - http://dx.doi.org/10.3389/fphys.2021.714655 SN - 1664-042X VL - 12 PB - Frontiers Research Foundation CY - Lausanne ER - TY - THES A1 - Monse, Henry T1 - (K)eine Opposition: Die Wahlkampfgestaltung der SPD und CDU von 1945—1990 im historischen Kontext N2 - Im Zentrum des Buches stehen die beiden Volksparteien CDU und SPD, die sich als gegensätzliche, gar verfeindete Parteien startend, gegenwärtig in ihren visuellen und inhaltlichen Identitäten immer unerkenntlicher vermischen. Das Buch geht dem Ursprung dieser Vermischung auf die Spur und untersucht inwiefern sich die visuellen Identitäten der beiden Parteien zwischen 1945 und 1990 in Form der Gestaltung nach außen aneinander angeglichen haben und wer wann federführend in der Gestaltung war. Beginnend 1945 in der »Stunde Null« führt das Buch in den einzelnen Kapiteln durch das Zeitgeschehen der Bundesrepublik bis ins Jahr 1990. Der historische Querschnitt beleuchtet dabei das gesellschaftspolitische Zeitgeschehen, das den Wahlkämpfen zugrunde liegt. Dabei stehen die politischen Wahlplakate im Fokus der Untersuchung: SPD und CDU — (k)eine gestalterische Opposition? KW - Bundesrepublik Deutschland KW - Parteien KW - Opposition Y1 - 2021 PB - FH Aachen CY - Aachen ER - TY - JOUR A1 - Monakhova, Yulia A1 - Diehl, Bernd W.K. T1 - Novel approach of qNMR workflow by standardization using 2H integral: Application to any intrinsic calibration standard JF - Talanta N2 - Quantitative nuclear magnetic resonance (qNMR) is routinely performed by the internal or external standardization. The manuscript describes a simple alternative to these common workflows by using NMR signal of another active nuclei of calibration compound. For example, for any arbitrary compound quantification by NMR can be based on the use of an indirect concentration referencing that relies on a solvent having both 1H and 2H signals. To perform high-quality quantification, the deuteration level of the utilized deuterated solvent has to be estimated. In this contribution the new method was applied to the determination of deuteration levels in different deuterated solvents (MeOD, ACN, CDCl3, acetone, benzene, DMSO-d6). Isopropanol-d6, which contains a defined number of deuterons and protons, was used for standardization. Validation characteristics (precision, accuracy, robustness) were calculated and the results showed that the method can be used in routine practice. Uncertainty budget was also evaluated. In general, this novel approach, using standardization by 2H integral, benefits from reduced sample preparation steps and uncertainties, and can be applied in different application areas (purity determination, forensics, pharmaceutical analysis, etc.). KW - qNMR KW - Deuterium NMR KW - Deuterated solvents KW - Standardization Y1 - 2021 SN - 0039-9140 U6 - http://dx.doi.org/10.1016/j.talanta.2020.121504 VL - 222 IS - Article number: 121504 PB - Elsevier ER - TY - JOUR A1 - Monakhova, Yulia A1 - Diehl, Bernd W. K. T1 - Simplification of NMR Workflows by Standardization Using 2H Integral of Deuterated Solvent as Applied to Aloe vera Preparations JF - Applied Magnetic Resonance N2 - In this study, a recently proposed NMR standardization approach by 2H integral of deuterated solvent for quantitative multicomponent analysis of complex mixtures is presented. As a proof of principle, the existing NMR routine for the analysis of Aloe vera products was modified. Instead of using absolute integrals of targeted compounds and internal standard (nicotinamide) from 1H-NMR spectra, quantification was performed based on the ratio of a particular 1H-NMR compound integral and 2H-NMR signal of deuterated solvent D2O. Validation characteristics (linearity, repeatability, accuracy) were evaluated and the results showed that the method has the same precision as internal standardization in case of multicomponent screening. Moreover, a dehydration process by freeze drying is not necessary for the new routine. Now, our NMR profiling of A. vera products needs only limited sample preparation and data processing. The new standardization methodology provides an appealing alternative for multicomponent NMR screening. In general, this novel approach, using standardization by 2H integral, benefits from reduced sample preparation steps and uncertainties, and is recommended in different application areas (purity determination, forensics, pharmaceutical analysis, etc.). Y1 - 2021 U6 - http://dx.doi.org/10.1007/s00723-021-01393-4 SN - 1613-7507 VL - 52 IS - 11 SP - 1591 EP - 1600 PB - Springer CY - Cham ER - TY - JOUR A1 - Monakhova, Yulia A1 - Diehl, Bernd W. K. T1 - A step towards optimization of the qNMR workflow: proficiency testing exercise at an GxP-accredited laboratory JF - Applied Magnetic Resonance N2 - Quantitative nuclear magnetic resonance (qNMR) is considered as a powerful tool for multicomponent mixture analysis as well as for the purity determination of single compounds. Special attention is currently paid to the training of operators and study directors involved in qNMR testing. To assure that only qualified personnel are used for sample preparation at our GxP-accredited laboratory, weighing test was proposed. Sixteen participants performed six-fold weighing of the binary mixture of dibutylated hydroxytoluene (BHT) and 1,2,4,5-tetrachloro-3-nitrobenzene (TCNB). To evaluate the quality of data analysis, all spectra were evaluated manually by a qNMR expert and using in-house developed automated routine. The results revealed that mean values are comparable and both evaluation approaches are free of systematic error. However, automated evaluation resulted in an approximately 20% increase in precision. The same findings were revealed for qNMR analysis of 32 compounds used in pharmaceutical industry. Weighing test by six-fold determination in binary mixtures and automated qNMR methodology can be recommended as efficient tools for evaluating staff proficiency. The automated qNMR method significantly increases throughput and precision of qNMR for routine measurements and extends application scope of qNMR. Y1 - 2021 U6 - http://dx.doi.org/10.1007/s00723-021-01324-3 SN - 1613-7507 N1 - Corresponding author: Yulia Monakhova VL - 52 SP - 581 EP - 593 PB - Springer Nature CY - Wien ER - TY - JOUR A1 - Molinnus, Denise A1 - Drinic, Aleksander A1 - Iken, Heiko A1 - Kröger, Nadja A1 - Zinser, Max A1 - Smeets, Ralf A1 - Köpf, Marius A1 - Kopp, Alexander A1 - Schöning, Michael Josef T1 - Towards a flexible electrochemical biosensor fabricated from biocompatible Bombyx mori silk JF - Biosensors and Bioelectronics Y1 - 2021 U6 - http://dx.doi.org/10.1016/j.bios.2021.113204 SN - 0956-5663 VL - 183 IS - Art. 113204 PB - Elsevier CY - Amsterdam ER -