TY  - JOUR
A1  - Kowalewski, Paul
A1  - Bragard, Michael
A1  - Hüning, Felix
A1  - De Doncker, Rik W.
T1  - An inexpensive Wiegand-sensor-based rotary encoder without rotating magnets for use in electrical drives
JF  - IEEE Transactions on Instrumentation and Measurement
N2  - This paper introduces an inexpensive Wiegand-sensor-based rotary encoder that avoids rotating magnets and is suitable for electrical-drive applications. So far, Wiegand-sensor-based encoders usually include a magnetic pole wheel with rotating permanent magnets. These encoders combine the disadvantages of an increased magnet demand and a limited maximal speed due to the centripetal force acting on the rotating magnets. The proposed approach reduces the total demand of permanent magnets drastically. Moreover, the rotating part is manufacturable from a single piece of steel, which makes it very robust and cheap. This work presents the theoretical operating principle of the proposed approach and validates its benefits on a hardware prototype. The presented proof-of-concept prototype achieves a mechanical resolution of 4.5 ° by using only 4 permanent magnets, 2Wiegand sensors and a rotating steel gear wheel with 20 teeth.
KW  - Rotary encoder
KW  - Wiegand sensor
Y1  - 2023
U6  - http://dx.doi.org/10.1109/TIM.2023.3326166
SN  - 0018-9456 (Print)
SN  - 1557-9662 (Online)
N1  - Early Access
SP  - 10 Seiten
PB  - IEEE
ER  - 
TY  - JOUR
A1  - Wiegner, Jonas
A1  - Volker, Hanno
A1  - Mainz, Fabian
A1  - Backes, Andreas
A1  - Loeken, Michael
A1  - Hüning, Felix
T1  - Energy analysis of a wireless sensor node powered by a Wiegand sensor
JF  - Journal of Sensors and Sensor Systems (JSSS)
N2  - This article describes an Internet of things (IoT) sensing device with a wireless interface which is powered by the energy-harvesting method of the Wiegand effect. The Wiegand effect, in contrast to continuous sources like photovoltaic or thermal harvesters, provides small amounts of energy discontinuously in pulsed mode. To enable an energy-self-sufficient operation of the sensing device with this pulsed energy source, the output energy of the Wiegand generator is maximized. This energy is used to power up the system and to acquire and process data like position, temperature or other resistively measurable quantities as well as transmit these data via an ultra-low-power ultra-wideband (UWB) data transmitter. A proof-of-concept system was built to prove the feasibility of the approach. The energy consumption of the system during start-up was analysed, traced back in detail to the individual components, compared to the generated energy and processed to identify further optimization options. Based on the proof of concept, an application prototype was developed.
Y1  - 2023
U6  - http://dx.doi.org/10.5194/jsss-12-85-2023
SN  - 2194-878X
N1  - Corresponding author: Felix Hüning
VL  - 12
IS  - 1
SP  - 85
EP  - 92
PB  - Copernicus Publ.
CY  - Göttingen
ER  - 
TY  - JOUR
A1  - Hüning, Felix
A1  - Backes, Andreas
T1  - Direct observation of large Barkhausen jump in thin Vicalloy wires
JF  - IEEE Magnetics Letters
Y1  - 2020
SN  - 1949-307X
U6  - http://dx.doi.org/10.1109/LMAG.2020.3046411
VL  - 11
IS  - Art. 2506504
SP  - 1
EP  - 4
PB  - IEEE
CY  - New York, NY
ER  - 
TY  - JOUR
A1  - Hüning, Felix
A1  - De Matteis, Stefan
T1  - Entwicklung eines taktilen HMI für sehbehinderte und blinde Nutzerinnen und Nutzer
JF  - Blind - sehbehindert
Y1  - 2020
SN  - 0176-7836
VL  - 140
IS  - 2
SP  - 9
EP  - 19
PB  - Edition Bentheim
CY  - Würzburg
ER  - 
TY  - JOUR
A1  - Hüning, Felix
T1  - Nachrüstmöglichkeiten von Dieselfahrzeugen aus technischer Sicht
JF  - Zeitschrift für Verkehrsrecht : NZV
Y1  - 2019
IS  - 1
SP  - 27
EP  - 32
PB  - C.H.Beck
ER  - 
TY  - JOUR
A1  - Hüning, Felix
A1  - Heuermann, Holger
A1  - Wache, Franz-Josef
T1  - Wireless CAN without WLAN or Bluetooth
JF  - CAN Newsletter
N2  - In two developed concepts, dual-mode radio enables CAN participants to be integrated wirelessly into a CAN network. Constructed from a few components, a protocol-free, real-time transmission and thus transparent integration into CAN is provided.
Y1  - 2018
IS  - December 2018
SP  - 44
EP  - 46
ER  - 
TY  - JOUR
A1  - Hüning, Felix
A1  - Heuermann, Holger
A1  - Wache, Franz-Josef
T1  - Wireless CAN
JF  - Etz: Elektrotechnik & Automation
N2  - In modernen elektronischen und mechatronischen Systemen, z. B. im industriellen oder automobil Bereich, kommunizieren eingebettete Steuergeräte und Sensoren vielfach über Bussysteme wie CAN oder LIN. Die Kommunikation findet in der Regel drahtgebunden statt, so dass der Kabelbaum für die Kommunikation sehr groß werden kann. Daher ist es naheliegend, Leitungen und dazugehörige Stecker, z. B. für nicht-sicherheitskritische Komfortsysteme, einzusparen und diese durch gerichtete Funkstrecken für kurze Entfernungen zu ersetzen. Somit könnten Komponenten wie ECUs oder Sensoren kabel- und steckerlos in ein Bussystem integriert werden. Zudem ist eine einfache galvanische und mechanische Trennung zu erreichen. Funkübertragung wird bei diesen Bussystemen derzeit nicht eingesetzt, da insbesondere die Echtzeitfähigkeit und die Robustheit der vorhandenen Funksysteme nicht den Anforderungen der Anwendungen entspricht. Zudem sind bestehende Funksysteme wie WLAN oder Bluetooth im Vergleich zur konventionellen Verkabelung teuer und es besteht hierbei die Möglichkeit, dass sie ausspioniert werden können und so sensible Daten entwendet werden können. In dieser Arbeit wird eine alternative Realisierung zu den bestehenden Funksystemen vorgestellt, die aus wenigen Komponenten aufzubauen ist. Es ist eine protokolllose, echtzeitfähige Übertragung möglich und somit die transparente Integration in ein Bussystem wie CAN.
Y1  - 2018
SN  - 0170-1711
VL  - 139
IS  - 10
SP  - 22
EP  - 26
PB  - VDE-Verlag
CY  - Wuppertal
ER  - 
TY  - JOUR
A1  - Hüning, Felix
A1  - Heuermann, Holger
A1  - Wache, Franz-Josef
A1  - Jajo, Rami Audisho
T1  - A new wireless sensor interface using dual-mode radio
JF  - Journal of Sensors and Sensor Systems : JSSS
N2  - The integration of sensors is one of the major tasks in embedded, control and “internet of things” (IoT) applications. For the integration mainly digital interfaces are used, starting from rather simple pulse-width modulation (PWM) interface to more complex interfaces like CAN (Controller Area Network). Even though these interfaces are tethered by definition, a wireless realization is highly welcome in many applications to reduce cable and connector cost, increase the flexibility and realize new emerging applications like wireless control systems. Currently used wireless solutions like Bluetooth, WirelessHART or IO-Link Wireless use dedicated communication standards and corresponding higher protocol layers to realize the wireless communication. Due to the complexity of the communication and the protocol handling, additional latency and jitter are introduced to the data communication that can meet the requirements for many applications. Even though tunnelling of other bus data like CAN data is generally also possible the latency and jitter prevent the tunnelling from being transparent for the bus system. Therefore a new basic technology based on dual-mode radio is used to realize a wireless communication on the physical layer only, enabling a reliable and real-time data transfer. As this system operates on the physical layer it is independent of any higher layers of the OSI (open systems interconnection) model. Hence it can be used for several different communication systems to replace the tethered physical layer. A prototype is developed and tested for real-time wireless PWM, SENT (single-edge nibble transmission) and CAN data transfer with very low latency and jitter.
Y1  - 2018
U6  - http://dx.doi.org/10.5194/jsss-7-507-2018
VL  - Volume 7
IS  - 2
SP  - 507
EP  - 515
PB  - Copernicus Publ.
CY  - Göttingen
ER  - 
TY  - JOUR
A1  - Hüning, Felix
T1  - Die Anforderungen steigen : Entwicklungstrends bei MOSFETs für den Automobilbereich
JF  - Elektronik-Industrie. 39 (2008), H. 5
Y1  - 2008
SN  - 0174-5522
SP  - 74
EP  - 76
PB  - -
ER  - 
TY  - JOUR
A1  - Hüning, Felix
T1  - Using Trench PowerMOSFETs in Linear Mode
JF  - Power Electronics Europe (2012)
N2  - If we think about applications for modern Power MOSFETs using trench technology, running them in linear mode may not be top of the priority list. Yet there are multiple uses for Trench Power MOSFETs in linear mode. In fact, even turning the device on and off in switching applications is a form of linear operation. Also, these components can be run in linear mode to protect the device against voltage surges. This article will illustrate the factors that need to be considered for linear operation and show how Trench Power MOSFETs are suited to it.
Y1  - 2012
SN  - 1748-3530
SP  - 27
EP  - 29
PB  - DFA Media
CY  - Tonbridge
ER  - 
TY  - JOUR
A1  - Hüning, Felix
T1  - PowerMOSFETs in ANL2-Technologie : Ansteuerungen bis in den kW-Bereich mit wenig Verlustleistung und Platzbedarf
JF  - Elektronik-Industrie
Y1  - 2011
SN  - 0174-5522
VL  - 42
IS  - 10
SP  - 36
EP  - 39
PB  - Hüthig
CY  - Heidelberg
ER  - 
TY  - JOUR
A1  - Hüning, Felix
T1  - Hart im Nehmen : Low-Voltage-Powermosfets mit Super-Junction-1-Technologie optimieren
JF  - Elektronik-Journal. 44 (2009), H. 12
Y1  - 2009
SN  - 0013-5674
SP  - 36
EP  - 38
PB  - -
ER  - 
TY  - JOUR
A1  - Hüning, Felix
T1  - Mosfet ottimizzati per l’automotive
JF  - Selezione di Elettronica (2009)
Y1  - 2009
SP  - 115
EP  - 117
PB  - -
ER  - 
TY  - JOUR
A1  - Hüning, Felix
T1  - Entwicklungstrends bei MOSFETs für den Automobilbereich
JF  - Elektronik-Industrie . 39 (2008), H. 5
Y1  - 2008
SN  - 0174-5522
SP  - 74
EP  - 76
PB  - -
ER  - 
TY  - JOUR
A1  - Hüning, Felix
T1  - SMD packages for PowerMOSFETs in automotive applications – developments and trends
JF  - Automotive Designline Europe  (2009)
Y1  - 2009
PB  - -
ER  - 
TY  - JOUR
A1  - Hüning, Felix
A1  - Eifert, T.
A1  - Handrick, K.
A1  - Neuhausen, U.
T1  - Computational Magnetochemistry: Complementary Quantum Mechanical Tools / Eifert, T. ; Handrick, K. ; Hüning, F. ; Neuhausen, U. ; Schilder, H. ; Lueken, H.
JF  - 20 Jahre Wilhelm-Klemm-Stiftung / Kuratorium der Wilhelm-Klemm-Stiftung (Hrsg.)
Y1  - 2006
SN  - 978-3-8322-5520-6
SP  - 193ff
PB  - Shaker
CY  - Aachen
ER  - 
TY  - JOUR
A1  - Hüning, Felix
T1  - Robusti affidabili per le Sfide dell’automotive
JF  - Selezione di Elettronica (2008)
Y1  - 2008
SP  - 116
EP  - 117
PB  - -
ER  - 
TY  - JOUR
A1  - Hüning, Felix
A1  - Luken, Heiko
A1  - Schilder, Herbert
A1  - Eifert, Thomas
T1  - Magnetochemistry: Compounds and Concepts / Lueken, Heiko ; Schilder, Herbert ; Eifert, Thomas ; Handrick, Klaus ; Hüning, Felix
JF  - Advances in Solid State Physics. 201 (2001)
Y1  - 2001
SP  - 515
EP  - 532
PB  - -
ER  - 
TY  - JOUR
A1  - Hüning, Felix
A1  - Eifert, T.
A1  - Lueken, H.
A1  - Schmidt, P.
T1  - High-temperature series expansion of the magnetic susceptibility of extended magnetic systems in a complete computer implementation / Eifert, T. ; Hüning, F. ; Lueken, H. ; Schmidt, P. ; Thiele, G.
JF  - Chemical Physics Letters. 364 (2002), H. 1-2
Y1  - 2002
SN  - 0009-2614
SP  - 69
EP  - 74
PB  - -
ER  - 
TY  - JOUR
A1  - Hüning, Felix
A1  - Eifert, T.
A1  - Handrick, K.
A1  - Neuhausen, U.
T1  - Computational Magnetochemistry: Complementary Quantum Mechanical Tools / Eifert, T. ; Handrick, K. ; Hüning, F. ; Neuhausen, U. ; Schilder, H. ; Lueken, H.
JF  - Zeitschrift für Anorganische und Allgemeine Chemie (ZAAC) - Journal of Inorganic and General Chemistry . 632 (2006), H. 4
Y1  - 2006
SN  - 1521-3749
SP  - 521
EP  - 529
PB  - -
ER  -