TY - JOUR A1 - Kern, Alexander A1 - Krichel, Frank T1 - Überlegungen zum Blitzschutzkonzept für regenerative Energieanlagen N2 - Dem Blitzschutz von Anlagen der regenerativen Energien kommt in Zukunft eine steigende Bedeutung zu. Dabei ist es notwendig zu berücksichtigen, dass die Schutzmaßnahmen technisch/wirtschaftlich ausgewogen sind. Erbauer, Besitzer oder Benutzer von netzautarken Hybridanlagen haben zu entscheiden, ob die Anlage einen Schutz braucht oder nicht. Um diese Entscheidung zu fällen, ist eine Risikoanalyse als erster Schritt sinnvoll. Diese muss dabei die für die Hybridanlage relevanten Schadenarten und spezifischen Parameter, Werte und Randbedingungen mit einbeziehen. Dazu ist die Hilfe eines Blitzschutzexperten sehr hilfreich. KW - Alternative Energiequelle KW - Energietechnische Anlage KW - Blitzschutz KW - Blitzschutz KW - Regenerative Energieanlagen KW - Lightning protection KW - renewable energy Y1 - 2003 ER - TY - JOUR A1 - Kämper, Klaus-Peter A1 - Picard, Antoni A1 - Brill, Manfred A1 - Cassel, Detlev A1 - Jentsch, Andreas A1 - Merten, Sabine A1 - Rollwa, Markus T1 - The Virtual Clean Room - a new tool in teaching MST process technologies N2 - The Virtual Clean Room - a new tool in teaching MST process technologies University education in high-technology fields like MST is not complete without intensive laboratory sessions. Students cannot fully grasp the complexity and the special problems related to the manufacturing of microsystems without a thorough hands-on experience in a MST clean room. KW - Virtuelle Maschine KW - VM KW - Mikrosystemtechnik KW - MST KW - virtual clean room Y1 - 2003 ER - TY - JOUR A1 - Schermutzki, Margret A1 - Kluß, Stefan T1 - Kontaktstunden oder workload? Die Vergabe von ECTS credits N2 - Informationen darüber, wie die Arbeitsbelastung (workload) der Studierenden ermittelt werden kann KW - Bologna-Prozess KW - ECTS KW - Kontaktstunden KW - Arbeitsbelastung KW - Europäisches Leistungspunktesystem KW - Bewertung von Studienleistungen KW - European Credit Transfer System KW - Workload Y1 - 2004 ER - TY - JOUR A1 - Staat, Manfred T1 - Plastic collapse analysis of longitudinally flawed pipes and vessels N2 - Improved collapse loads of thick-walled, crack containing pipes and vessels are suggested. Very deep cracks have a residual strength which is better modelled by a global limit load. In all burst tests, the ductility of pressure vessel steels was sufficiently high whereby the burst pressure could be predicted by limit analysis with no need to apply fracture mechanics. The relative prognosis error increases however, for long and deep defects due to uncertainties of geometry and strength data. KW - Druckbehälter KW - Stahl KW - Druckbelastung KW - Druckbeanspruchung KW - Rohr KW - Rohrbruch KW - Druckbehälter KW - Stahl KW - Druckbelastung KW - Druckbeanspruchung KW - Rohrbruch KW - Fehlerstellen KW - pipes KW - vessels KW - load limit KW - burst tests KW - burst pressure KW - flaw Y1 - 2004 ER - TY - JOUR A1 - Vu, Duc-Khoi A1 - Staat, Manfred T1 - An algorithm for shakedown analysis of structure with temperature dependent yield stress N2 - This work is an attempt to answer the question: How to use convex programming in shakedown analysis of structures made of materials with temperature-dependent properties. Based on recently established shakedown theorems and formulations, a dual relationship between upper and lower bounds of the shakedown limit load is found, an algorithmfor shakedown analysis is proposed. While the original problem is neither convex nor concave, the algorithm presented here has the advantage of employing convex programming tools. KW - Einspielen KW - Temperaturabhängigkeit KW - Fließgrenze KW - Shakedown KW - shakedown analysis KW - yield stress Y1 - 2004 ER - TY - JOUR A1 - Kühn, Raoul-Roman A1 - Haugner, Werner A1 - Staat, Manfred A1 - Sponagel, Stefan T1 - A Two Phase Mixture Model based on Bone Observation N2 - An optimization method is developed to describe the mechanical behaviour of the human cancellous bone. The method is based on a mixture theory. A careful observation of the behaviour of the bone material leads to the hypothesis that the bone density is controlled by the principal stress trajectories (Wolff’s law). The basic idea of the developed method is the coupling of a scalar value via an eigenvalue problem to the principal stress trajectories. On the one hand this theory will permit a prediction of the reaction of the biological bone structure after the implantation of a prosthesis, on the other hand it may be useful in engineering optimization problems. An analytical example shows its efficiency. KW - Knochen KW - Knochenbildung KW - Knochenchirugie KW - Strukturanalyse KW - Schwammknochen KW - Knochendichte KW - Wolffsches Gesetz KW - bone structure KW - bone density KW - Wolff's Law KW - cancellous bone Y1 - 2004 ER - TY - JOUR A1 - Heger, Michael A1 - Kock, Winfried T1 - INGMEDIA, blended learning im Laborpraktikum. Ein hochschuldidaktisches Projekt T1 - INGMEDIA, blended learning in the laboratory practical course. A universitydidactical project N2 - Laborpraktika bieten Studierenden besondere Lernmöglichkeiten. Sie erleben im Praktikum mit Kopf (kognitiv), Herz (affektiv) und Hand (motorisch) Zusammenhänge und Zusammenarbeit. Durch die multimediale Vorbereitung und Unterstützung der Laborpraktika mit INGMEDIA können diese Lernvorteile intensiver genutzt werden. Vielfältige und differenzierte Kontextangebote bieten individuelle Lerneinstiegsmöglichkeiten und aktivieren zu Selbstgesteuertem Lernen. Durch die Verbesserung von Vorwissen und Motivation eröffnen scih Lehrenden und Lernenden neue Freiräume bei der Gestaltung der Präsenzveranstaltung. Durch hochschuldidaktische Aktionsforschung beim Einsatz im Lehrbetrieb wird die weitere Entwicklung von Software und Präsenzveranstaltung prozesshaft begleitet. N2 - Laboratory practical training courses offer special learning possibilities for university students. In practical training courses they experience contexts and team work by involving head (cognitive learning), heart (emotional / affective learning) and hand (motoric learning). Because of the multimedia-based preparation and support of the laboratory training courses by INGMEDIA these learning experiences can be used to a better advantage. Manifold and differentiated context-specific offers present individually chosen starting points and activate the self-directed learning process. The improvement of previous knowledge and motivation allows the teacher as well as the learner more freedom for the arrangement of the actual training course. University didactics-specific activity research in the course of the practical application will accompany the further development of both software and training course in a trial-like way. KW - Hochschuldidaktik KW - blended learning KW - Didactics KW - blended learning Y1 - 2004 ER - TY - JOUR A1 - Heger, Michael T1 - Konzept hochschuldidaktischer Aktionsforschung am Beispiel INGMEDIA N2 - "INGMEDIA: Entwicklung und Evaluation interaktiver, multimedialer Lernsoftware für technische und physikalische Praktika in Ingenieurstudiengängen". So lautet der Titel des vom bmb+f im Förderprogramm "Neue Medien in der Hochschullehre" unterstützten Verbundprojekts. [...] Im vorliegenden Beitrag wird über das Evaluationskonzept von INGMEDIA berichtet. Es handelt sich hierbei um einen im E-Learning-Bereich bisher kaum vertretenen Ansatz hochschuldidaktischer Aktionsforschung. Der Beitrag betont entsprechend des kevih - Tagungskonzepts (Tübingen 11./12.3.03) die besonderen hochschuldidaktischen Zielrichtungen, fokussiert also klar auf der konzeptionellen Ebene. Die Umsetzung und Evaluationsergebnisse zu INGMEDIA werden nach Projektabschluss an anderer Stelle veröffentlicht. KW - Hochschuldidaktik KW - E-Learning Y1 - 2004 ER - TY - JOUR A1 - Gebhardt, Andreas T1 - Grundlagen des Rapid Prototyping: Eine Kurzdarstellung der Rapid Prototyping Verfahren N2 - Generative Verfahren sind seit etwa 1987 in den USA und seit etwa 1990 in Europa und Deutschland in Form von Rapid Prototyping Verfahren bekannt und haben sich in dieser Zeit von eher als exotisch anzusehenden Modellbauverfahren zu effizienten Werkzeugen für die Beschleunigung der Produktentstehung gewandelt. Mit der Weiterentwicklung der Verfahren und insbesondere der Materialien wird mehr und mehr das Feld der direkten Anwendung der Rapid Technologie zur Fertigung erschlossen. Rapid Technologien werden daher zum Schlüssel für neue Konstruktionssystematiken und Fertigungsstrategien. N2 - Generative procedures have been known under the term of 'rapid prototyping method' for about 18 years in the USA and about 15 years in Europe and Germany. In this time they changed from what was regarded as being a rather exotic way of model construction procedures to a very efficient and useful instrument for faster product manufacturing. In the course of the further development of the methods, and in particular the materials, the field for direct application of rapid technology opens up for manufacturing. Therefore rapid technologies become the key for new construction systematics and manufacturing strategies. KW - Rapid prototyping KW - Laserstrahlsintern KW - 3D-Printing KW - Extrusionsverfahren KW - Gießharzwerkzeuge KW - Laminat Verfahren KW - Lasersintern KW - Stereolithographie KW - Vakuumgießen KW - FLM KW - Fused deposition modelling KW - Laminated-Object-Manufacturing Y1 - 2004 ER - TY - JOUR A1 - Staat, Manfred T1 - Local and global collapse pressure of longitudinally flawed pipes and cylindrical vessels N2 - Limit loads can be calculated with the finite element method (FEM) for any component, defect geometry, and loading. FEM suggests that published long crack limit formulae for axial defects under-estimate the burst pressure for internal surface defects in thick pipes while limit loads are not conservative for deep cracks and for pressure loaded crack-faces. Very deep cracks have a residual strength, which is modelled by a global collapse load. These observations are combined to derive new analytical local and global collapse loads. The global collapse loads are close to FEM limit analyses for all crack dimensions. KW - Finite-Elemente-Methode KW - Grenzwertberechnung KW - Axialbelastung KW - FEM KW - Grenzwertberechnung KW - Axialbelastung KW - Traglastanalyse KW - Limit analysis KW - Global and local collapse KW - Axially cracked pipe KW - Pressure loaded crack-face Y1 - 2005 ER - TY - JOUR A1 - Staat, Manfred T1 - Direct finite element route for design-by-analysis of pressure components N2 - In the new European standard for unfired pressure vessels, EN 13445-3, there are two approaches for carrying out a Design-by-Analysis that cover both the stress categorization method (Annex C) and the direct route method (Annex B) for a check against global plastic deformation and against progressive plastic deformation. This paper presents the direct route in the language of limit and shakedown analysis. This approach leads to an optimization problem. Its solution with Finite Element Analysis is demonstrated for mechanical and thermal actions. One observation from the examples is that the so-called 3f (3Sm) criterion fails to be a reliable check against progressive plastic deformation. Precise conditions are given, which greatly restrict the applicability of the 3f criterion. KW - Einspielen KW - Plastizität KW - Deformation KW - Analytischer Zulaessigkeitsnachweis KW - Einspiel-Analyse KW - fortschreitende plastische Deformation KW - alternierend Verformbarkeit KW - Einspiel-Kriterium KW - Design-by-analysis KW - Shakedown analysis KW - Progressive plastic deformation KW - Alternating plasticity KW - Shakedown criterion Y1 - 2005 ER - TY - JOUR A1 - Gebhardt, Andreas T1 - Rapid Prototyping für metallische Werkstücke: Direkte und indirekte Verfahren N2 - Die generative Herstellung von Kunststoffbauteilen hat im Gewand des Rapid Prototyping die Produktentwicklung nachhaltig positiv beeinflusst und ist im Begriff als Rapid Manufacturing die Fertigung zu revolutionieren. Je mehr sich die besonderen Eigenschaften generativ gefertigter Kunststoffbauteile herumsprechen, desto lauter wird der Ruf nach Metallbauteilen. Die Entwicklung entsprechender Prozesse läuft auf Hochtouren, kann aber bisher aber erst vereinzelt Erfolge vorweisen. Dabei wären es gerade die Metallbauteile, die ausgestattet mit den besonderen Merkmalen generativ gefertigter Werkstücke, in vielen Branchen einen deutlichen Entwicklungsschub auslösen könnten. Für den potenziellen Anwender ist dabei besonders verwirrend, dass die unterschiedlichsten Ansätze nebeneinander verfolgt werden. Im Folgenden soll daher der Versuche unternommen werden, dieses weite Feld systematisiert darzustellen und Möglichkeiten und Trends zu erläutern. N2 - The generative manufacturing of plastic components via rapid prototyping has positively affected the product development. As 'rapid manufacturing' the method is about to revolutionize the manufacturing in general. The more the special characteristics of generative manufactured plastic components are getting about, the louder becomes the call for generative manufactured metal components. The development of analogical processes runs on full speed. So far however, only sporadic successes can be registered. Though there are in particular the metal components which could, equipped with the special characteristics of generative manufactured components, initiate a developmental boost in many industries. For the potential operator it is particularly confusing that the different approaches are traced parallel. Therefore in the following contribution the attempt is undertaken not only to represent this wide field in a systematic way but to describe possibilities and trends as well. KW - Rapid prototyping KW - Rapid Prototyping KW - Rapid Manufacturing KW - generative Fertigungsverfahren KW - Werkzeugeinsätze KW - Werkzeuge KW - Rapid prototyping KW - rapid manufacturing Y1 - 2005 ER - TY - JOUR A1 - Gebhardt, Andreas A1 - Brücker, Christoph A1 - Schmidt, Frank-Michael T1 - RP gestützte Herstellung komplexer transparenter Hohlräume für die Strömungsanalyse N2 - Die Berechnung der Durchströmung von Bauteilen ist gegenüber derjenigen von umströmten Bauteilen deutlich im Hintertreffen. Das liegt vor allem an der fehlenden Verfügbarkeit geeigneter optisch transparenter Modellkanäle für die experimentelle Analyse. Der Beitrag stellt ein Verfahren zur Herstellung transparenter durchströmter Geometrien auf der Basis generativ gefertigter Urmodelle vor. Damit können beliebig komplexe Innenströmungen optisch analysiert werden. Anhand von zwei Beispielen aus der Medizin, der Modellierung der oberen Atemwege und des Bronchialbaums, wird das Verfahren vorgeführt. Der generative Bauprozess mittels 3D-Printing wird beschrieben und die Abformung in transparentem Silikon gezeigt. Schließlich werden beispielhaft der Messaufbau und Ergebnisse der Anwendung vorgestellt. Das Verfahren bildet die Grundlage für die Analyse und Berechnung komplexer Innenströmungen und trägt somit zur Verbesserung zahlreicher technischer Anwendungen bei. N2 - Unlike the flow around technical products the interior flow is not understood very well. That’s mainly because of a lack of suitable transparent investigation tunnels that are needed to apply optical methods. The paper proposes a procedure to make precise complex hollow structures from a highly transparent material using masters from generative or Rapid Prototyping processes. Taking two examples from the medical field, the upper human airways and the bronchial tree, the entire process is shown. The 3D Printing build process is illustrated as well as the silicon casting process. Finally the measuring equipment is demonstrated and sample results are given. The process establishes the basis for the investigation and calculation of complex interior flow pattern and therefore contributes to a better understanding and consequently improvement of appropriate technical products. KW - Rapid prototyping KW - Rapid Prototyping KW - Strömungsanalyse KW - Innenströmung KW - Modellkanäle KW - 3D-Printing Y1 - 2005 ER - TY - JOUR A1 - Matheis, Anton A1 - Röth, Thilo A1 - Wagner, Manfred T1 - Studentenprojekt "Capro" – eine virtuelle Sportwagenstudie "Vision 2015" N2 - Design- und Karosseriebaustudenten der FH Aachen entwickeln gemeinsam mit externen Fachleuten unter Einsatz virtueller Entwicklungswerkzeuge ein Konzept für einen Sportwagen KW - Karosseriebau KW - Sportwagen KW - Kraftfahrzeugbau KW - Studentenprojekt KW - Virtuelle Fahrzeugentwicklung KW - car body construction Y1 - 2005 ER - TY - JOUR A1 - Dick, Angela A1 - Wagner, Manfred A1 - Röth, Thilo T1 - Capro Automotive Group FH Aachen N2 - Design- und Karosseriebaustudenten der FH Aachen entwickeln gemeinsam mit externen Fachleuten unter Einsatz virtueller Entwicklungswerkzeuge ein Konzept für einen Sportwagen KW - Karosseriebau KW - Sportwagen KW - Kraftfahrzeugbau KW - Studentenprojekt KW - Virtuelle Fahrzeugentwicklung KW - car body construction Y1 - 2005 ER - TY - JOUR A1 - Gebhardt, Andreas T1 - Rapid Manufacturing - eine interdisziplinäre Strategie N2 - Als um 1987 ein Verfahren namens Stereolithographie und ein Stereolithography Apparatus (SLA) vorgestellt wurden, war der Traum von der Herstellung beliebiger dreidimensionaler Bauteile direkt aus Computerdaten und ohne bauteilspezifische Werkzeuge Realität geworden. Ein Anwendungs-Szenario wurde gleich mitgeliefert. Diese Technologie würde es möglich machen, die gesamte Ersatzteilversorgung der Amerikanischen Pazifikflotte mittels ein paar dieser Maschinen, umfangreicher Datenstätze und genügend Rohmaterial vor Ort auf einem Flugzeugträger direkt nach Bedarf zu fertigen. Diese Vorstellung definierte schon damals die direkte digitale Fertigung, das Rapid Manufacturing. In der Realität bestanden die mit diesem Verfahren hergestellten Bauteile nur aus Kunststoff, waren ungenau, bruchempfindlich und klebrig und allein in der Produktentwicklung, eben als Prototypen zu benutzen. Sie waren schnell verfügbar, weil zu Ihrer Herstellung keine Werkzeuge benötigt wurden. Folgerichtige und zudem modern hießen sie: Rapid Prototyping. Rapid Prototyping wurde schnell zum Synonym eines neuen Zweiges der Fertigungstechnik, der Generativen Fertigungstechnik. Die weitere Entwicklung brachte neue Verfahren, höhere Genauigkeiten, verbesserte Werkstoffe und neue Anwendungen. Die Herstellung von Negativen, also Werkzeugen, mit dem gleichen Verfahren wurde marketing-getrieben Rapid Tooling genannt und als die ersten Bauteile nicht mehr als Prototypen, sondern als Endprodukte eingesetzt wurden, nannte man dies Rapid Manufacturing - das Ziel war erreicht. War das Ziel wirklich erreicht? Ist es Rapid Manufacturing, wenn ein generativ gefertigtes Bauteil die gewünschte Spezifikation erreicht? Was muss passieren, damit aus dem Phänomen Rapid Prototyping eine Strategie wird, die geeignet ist, einen Paradigmenwechsel von der heutigen Hersteller-induzierten Massenproduktion von Massenartikeln zur Verbraucher-induzierten (und verantworteten) Massenproduktion von Einzelteilen für jedermann ermöglichen und möglicherweise unsere Arbeits- und Lebensformen tiefgreifend zu beeinflussen? Im Beitrag wird der Begriff der (Fertigungs-) Strategie „Rapid Manufacturing“ näher beleuchtet. Es wird diskutiert, welche Maßnahmen auf der technischen und der operative Ebene getroffen werden müssen, damit die generative Fertigungstechnik im Sinne dieser Strategie umgesetzt werden kann. Beispiele belegen, dass diese Entwicklung bereits begonnen hat und geben Anregungen für eine konstruktive Diskussion auf der RapidTech 2006. N2 - As a process called stereolithography and a stereolithography apparatus (SLA) was presented in 1987, the dream of manufacturing any three-dimensional component directly from computer data and without component-specific tools became reality. An application scenario was supplied at the same time. This technology would make it possible to produce the entire spare parts requirement of the American Pacific Fleet merely through the use of a couple of such machines, extensive datasets and enough raw material on board an aircraft carrier directly as required. This image defined direct digital fabrication, rapid manufacturing, even at that time. In reality, this procedure only managed to produce components in plastic which were imprecise, fragile and sticky and only usable as prototypes in product development. They were rapidly available, because no tools were required for their manufacture. Consequentially, they are now known as Rapid Prototyping in modern jargon. Rapid Prototyping quickly became a synonym for a new branch of production engineering known as generative production engineering. Continued development brought new processes, improved accuracy, improved materials and new applications. The manufacturing of negatives, in other words tools, using the same procedure was quickly named rapid tooling by the marketing sector, and once the first components were used as final products instead of just prototypes the process was renamed "rapid manufacturing" - the goal had been reached. Was the goal really reached? Is it rapid manufacturing if a generatively manufactured component reaches the required specifications? What has to happen so that the rapid prototyping phenomenon becomes a strategy which is suitable for enabling the paradigm change from current manufacture-induced mass production of mass articles to consumer-induced (and consumer-responsible) mass production of single parts for anyone, and in all possibility makes dramatic changes in our way of working and living? The lecture includes detailed information about the (production) strategy term "rapid manufacturing". We will be discussing which measures need to be taken on the technical and operative level so that generative production engineering can be implemented in the sense of this strategy. Examples will show that this development has already started, and should provoke stimulation leading to constructive discussion during RapidTech 2006. KW - Rapid prototyping KW - Rapid Manufacturing KW - Rapid Prototyping KW - Stereolithographie KW - Generative Fertigungstechnik KW - Rapid prototyping KW - rapid manufacturing Y1 - 2006 ER - TY - JOUR A1 - Gebhardt, Andreas T1 - Generative Manufacturing of Ceramic Parts "Vision Rapid Prototyping" N2 - Table of Contents Introduction 1. Generative Manufacturing Processes 2. Classification of Generative Manufacturing Processes 3. Application of Generative Processes on the Fabrication of Ceramic Parts 3.1 Extrusion 3.2 3D-Printing 3.3 Sintering – Laser Sintering 3.4 Layer-Laminate Processes 3.5 Stereolithography (sometimes written: Stereo Lithography) 4. Layer Milling 5. Conclusion - Vision KW - Rapid prototyping KW - Rapid Technologie KW - Rapid Prototyping Y1 - 2006 ER - TY - JOUR A1 - Kraft, Bodo A1 - Nagl, Manfred T1 - Visual Knowledge Specification for Conceptual Design: Definition and Tool Support N2 - In: Advanced Engineering Informatics. Vol 21, Issue 1, 2007, Pages 67-83 http://dx.doi.org/10.1016/j.aei.2006.10.001 eds. J.C. Kunz, I.F.C. Smith and T. Tomiyama, Elsevier, Seite 1-22 Current CAD tools are not able to support the conceptual design phase, and none of them provides a consistency analysis for sketches produced by architects. This phase is fundamental and crucial for the whole design and construction process of a building. To give architects a better support, we developed a CAD tool for conceptual design and a knowledge specification tool. The knowledge is specific to one class of buildings and it can be reused. Based on a dynamic and domain-specific knowledge ontology, different types of design rules formalize this knowledge in a graph-based form. An expressive visual language provides a user-friendly, human readable representation. Finally, a consistency analysis tool enables conceptual designs to be checked against this formal conceptual knowledge. In this article, we concentrate on the knowledge specification part. For that, we introduce the concepts and usage of a novel visual language and describe its semantics. To demonstrate the usability of our approach, two graph-based visual tools for knowledge specification and conceptual design are explained. KW - CAD KW - CAD KW - Bauingenieurwesen KW - CAD KW - civil engineering Y1 - 2007 ER - TY - JOUR A1 - Zhubanova, Azhar A. A1 - Digel, Ilya A1 - Nojima, H. A1 - Artmann, Gerhard T1 - The use of bactericidal effects of cluster ions generated by plasma in medical biotechnology N2 - The most of conventional methods of air purification use the power of a fan to draw in air and pass it through a filter. The problem of bacterial contamination of inner parts of such a type of air conditioners in some cases draws attention towards alternative air-cleaning systems. Some manufacturers offer to use the ozone's bactericidal and deodorizing effects, but the wide spreading of such systems is restricted by the fact that toxic effects of ozone in respect of human beings are well known. In 2000 Sharp Inc. introduced "Plasma Cluster Ions (PCI)" air purification technology, which uses plasma discharge to generate cluster ions (I 0-14 ). This technology has been developed for those customers that are conscious about health and hygiene. In our experiments, we focused on some principal aspects of plasma-generated ions application - time-dependency and irreversibility of bactericidal action, spatial and kinetic characteristics of emitted cluster particles, their chemical targets in the microbial cells. KW - Clusterion KW - Raumluft KW - Luftreiniger KW - Plasmacluster ion technology KW - Air purification Y1 - 2007 ER - TY - JOUR A1 - Uibel, Thomas T1 - Bemessung stiftförmiger Verbindungsmittel in Brettsperrholz – Anwendung aktueller Forschungsergebnisse JF - Praktische Anwendung von Massivholzplatten : 39. Fortbildungskurs SAH Schweizerische Arbeitsgemeinschaft für Holzforschung ; 7./8. November 2007 in Weinfelden Y1 - 2007 SN - 3-906703-19-3 N1 - Fortbildungskurs SAH Schweizerische Arbeitsgemeinschaft für Holzforschung ; (39 ; 2007.11.07-08 ; Weinfelden) SP - 183 EP - 192 PB - SAH CY - Dübendorf ER -