TY  - JOUR
A1  - Ahmed, Essam
A1  - Reisgen, Uwe
A1  - Schleser, Markus
A1  - Mokrov, Oleg
T1  - On formability of tailor laser welded blanks of DP/TRIP steel sheets
JF  - Science and technology of welding and joining
N2  - This paper aims to evaluate the formability of tailor welded blanks of dual phase (DP600)/transformation induced plasticity (TRIP700) steel sheets. In this work, bead on plate butt joints of 2·5 mm DP600 and 1·2 mm TRIP700 steel sheets were performed using CO2 laser beam welding. Microhardness measurements and transverse tensile testing were carried out to characterise the welds. The formability of base metals and welds were investigated by standard Erichsen test. In a perpendicular tensile test to the weld line, all specimens were fractured at the TRIP base metal, and the strengths were somewhat higher than those of base metal. There was a significant reduction in formability caused by welding of the DP600/TRIP700 steel sheets, and the formability increased with increasing welding speed.
Y1  - 2010
U6  - http://dx.doi.org/10.1179/136217110X12731414739754
SN  - 1743-2936
VL  - 15
IS  - 5
SP  - 337
EP  - 342
PB  - Maney
CY  - Leeds
ER  - 
TY  - JOUR
A1  - Berg, Alexander-Karl
A1  - Schleser, Markus
A1  - Delidovich, Artem
A1  - Houben, Alexander
T1  - Ultraschallunterstützter Schmelzklebstoffauftrag
JF  - adhäsion KLEBEN & DICHTEN
Y1  - 2018
U6  - http://dx.doi.org/10.1007/s35145-018-0089-z
VL  - Volume 62
IS  - Issue 12
SP  - 32
EP  - 37
PB  - Springer
ER  - 
TY  - JOUR
A1  - Dilthey, Ulrich
A1  - Brandenburg, Annette
A1  - Schleser, Markus
T1  - Dispensing and application of unfilled adhesives in the micro range
JF  - Welding and cutting. 3 (2004), H. 4
Y1  - 2004
SN  - 1612-3433
SP  - 250
EP  - 254
ER  - 
TY  - JOUR
A1  - Dilthey, Ulrich
A1  - Schleser, Markus
A1  - Feldmann, Martin
A1  - Pak, Daniel
A1  - Geßler, Achim
T1  - Investigation of punctiform, plane and hybrid joints of textile-reinforced concrete parts
JF  - Cement and concrete composites
Y1  - 2008
SN  - 0958-9465
VL  - Vol. 30
IS  - iss. 2
SP  - 82
EP  - 87
ER  - 
TY  - JOUR
A1  - Dilthey, Ulrich
A1  - Schleser, Markus
A1  - Geßler, Achim
A1  - Rettweiler, Timo
A1  - Völling, Boris
T1  - Kleben textilbewehrter Betonbauteile
JF  - Schweissen und Schneiden : Fachzeitschrift für Schweißen und verwandte Verfahren. Jg. 57 (2005), Nr. 8
Y1  - 2005
SN  - 0036-7184
SP  - 373
EP  - 377
ER  - 
TY  - JOUR
A1  - Dilthey, Ulrich
A1  - Schleser, Markus
A1  - Hanisch, Vera
A1  - Gries, Thomas
T1  - Garnzugprüfung polymergetränkter Textilien für die Bewehrung von Beton
JF  - Technische Textilien
Y1  - 2006
SN  - 0323-3243
VL  - 49
IS  - 1
SP  - 48
EP  - 50
ER  - 
TY  - JOUR
A1  - Feldmann, Markus
A1  - Pak, Daniel
A1  - Geßler, Achim
A1  - Dilthey, Ulrich
A1  - Schleser, Markus
T1  - Bonded connections for textile reinforced concrete structures
JF  - Cailiao-gongcheng = Journal of materials engineering
Y1  - 2006
SN  - 1001-4381
IS  - Special iss.
SP  - 123
EP  - 127
ER  - 
TY  - JOUR
A1  - Feldmann, Markus
A1  - Pak, Daniel
A1  - Geßler, Achim
A1  - Schleser, Markus
T1  - Entwicklung eines Bemessungsmodells für punktförmige Verbindungen textibewehrter Betonbauteile
JF  - Bautechnik : Zeitschrift für den gesamten Ingenieurbau
Y1  - 2008
SN  - 0005-6820, 0341-1052, 0932-6359, 0932-8351, 0932-8351
N1  - Printausg. in der Bibliothek der FH Aachen vorhanden: 13 Z 177
VL  - Bd. 85
IS  - 2
SP  - 143
EP  - 147
ER  - 
TY  - JOUR
A1  - Glowania, Michael
A1  - Gries, Thomas
A1  - Schoene, Jens
A1  - Schleser, Markus
A1  - Reisgen, Uwe
T1  - Innovative coating technology for textile reinforcements of concrete applications
JF  - 13th International Congress on Polymers in Concrete : 10 - 12 February 2010, Funchal, Madeira, Portugal.(Key engineering materials. Vol. 466)
Y1  - 2011
SN  - 978-3-03785-008-4
SN  - 1013-9826 (E-Journal) ; 0252-1059 (Print)
SP  - 167
EP  - 173
PB  - Trans Tech Publications
CY  - Bäch
ER  - 
TY  - JOUR
A1  - Kampker, Achim
A1  - Schleser, Markus
A1  - Triebs, Johannes
A1  - Berg, Alexander-Karl
A1  - Hansen, Jan Ole
A1  - Fiedler, Falko
T1  - Bauteilintegrierte Vorrichtungsfunktionen im Karosseriebau : Aktuelle Ergebnisse im Forschungsprojekt ProeK
JF  - ZWF Zeitschrift für wirtschaftlichen Fabrikbetrieb
N2  - Das Forschungsprojekt Produktionseffizienz in der Kleinserie (ProeK) erarbeitet kostengünstige und effiziente Lösungsansätze für Prozessketten im Zukunftsfeld der Elektromobilität. Das Teilprojekt Karosserie setzt diese Zielsetzung durch innovative und praxisorientierte Produkt- und Prozesskonzepte mit neuartigen bauteilintegrierten Vorrichtungsfunktionen (BiV) um. Im Teilprojekt Außenhaut sollen Toleranzen adaptiv durch Anpassungen der Prozessparameter sowie Bauteilmanipulation kompensiert werden.
Y1  - 2018
U6  - http://dx.doi.org/10.3139/104.112012
SN  - 0947-0085
VL  - 113
IS  - 11
SP  - 767
EP  - 770
PB  - De Gruyter
CY  - Berlin
ER  - 
TY  - JOUR
A1  - Mukherjee, Krishnendu
A1  - Prahl, Ulrich
A1  - Bleck, Wolfgang
A1  - Reisgen, Uwe
A1  - Schleser, Markus
A1  - Abdurakhmanov, Aydemir
T1  - Characterization and modelling techniques for gas metal arc welding of DP 600 sheet steels
JF  - Materialwissenschaft und Werkstofftechnik
N2  - The objectives of the present work are to characterize the Gas Metal Arc Welding process of DP 600 sheet steel and to summarize the modelling techniques. The time-temperature evolution during the welding cycle was measured experimentally and modelled with the softwaretool SimWeld. To model the phase transformations during the welding cycle dilatometer tests were done to quantify the parameters for phase field modelling by MICRESS®. The important input parameters are interface mobility, nucleation density, etc. A contribution was made to include austenite to bainite transformation in MICRESS®. This is useful to predict the microstructure in the fast cooling segments. The phase transformation model is capable to predict the microstructure along the heating and cooling cycles of welding. Tensile tests have shown the evidence of failure at the heat affected zone, which has the ferrite-tempered martensite microstructure.
Y1  - 2010
U6  - http://dx.doi.org/10.1002/mawe.201000692
SN  - 1521-4052
VL  - 41
IS  - 11
SP  - 972
EP  - 983
PB  - Wiley-VCH
CY  - Weinheim
ER  - 
TY  - JOUR
A1  - Mukherjee, Krishnendu
A1  - Ramazani, Ali
A1  - Yang, Li
A1  - Prahl, Ulrich
A1  - Bleck, Wolfgang
A1  - Reisgen, Uwe
A1  - Schleser, Markus
A1  - Abdurakhmanov, Aydemir
T1  - Characterization of gas metal arc welded hot rolled DP600 steel
JF  - Steel research international
Y1  - 2011
SN  - 1869-344X (E-Book); 1611-3683 (Print)
VL  - Vol. 82
IS  - Iss. 12
SP  - 1408
EP  - 1416
PB  - Wiley
CY  - Weinheim
ER  - 
TY  - JOUR
A1  - Ramazani, Ali
A1  - Li, Yang
A1  - Mukherjee, Krishnendu
A1  - Prahl, Ulrich
A1  - Bleck, Wolfgang
A1  - Abdurakhmanov, Aydemir
A1  - Schleser, Markus
A1  - Reisgen, Uwe
T1  - Microstructure evolution simulation in hot rolled DP600 steel during gas metal arc welding
JF  - Computational materials science
Y1  - 2013
SN  - 1879-0801 (E-Book); 0927-0256 (Print)
VL  - Vol. 68
SP  - 107
EP  - 116
PB  - Elsevier
CY  - Amsterdam
ER  - 
TY  - JOUR
A1  - Reisgen, Uwe
A1  - Olschok, Simon
A1  - Jakobs, Stefan
A1  - Schleser, Markus
A1  - Mokrov, Oleg
A1  - Rossiter, Eduardo
T1  - Laser beam submerged arc hybrid welding
JF  - Physics procedia
N2  - The laser beam-submerged arc hybrid welding method originates from the knowledge that, with increasing penetration depth, the laser beam process has a tendency to pore formation in the lower weld regions. The coupling with the energy-efficient submerged-arc process improves degassing and reduces the tendency to pore formation. The high deposition rate of the SA process in combination with the laser beam process offers, providing the appropriate choice of weld preparation, the possibility of welding plates with a thickness larger than 20° mm in a single pass, and also of welding thicker plates with the double-sided single pass technique.
Y1  - 2012
U6  - http://dx.doi.org/10.1016/j.phpro.2012.10.016
SN  - 1875-3892
N1  - Part of special issue "Laser assisted net shape engineering 7 (LANE 2012)"
VL  - 39
SP  - 75
EP  - 83
PB  - Elsevier
CY  - Amsterdam
ER  - 
TY  - JOUR
A1  - Reisgen, Uwe
A1  - Schleser, Markus
A1  - Abdurakhmanov, Aydemir
A1  - Gumenyuk, Andrey
T1  - Measuring of plasma properties induced by non-vacuum electron beam welding
JF  - Physics of plasma
N2  - Electron beam plasma measurement was realised by means of DIABEAM system invented by ISF RWTH Aachen. The Langmuir probe method is used for measurement. The relative simplicity of the method and the possibility of dispersion of high power on the probe allow its application for the investigation of high-power electron beams. The key element of the method is a rotating thin tungsten wire, which intersects the beam transversely on its axis and collects part of the current by itself. The signals, which are registered in the DIABEAM as a voltage, were taken in the form of amplitude. The conversion of the probe current into the distribution along the beam radius was realised using the Abel’s method. A voltage-current characteristic was built for the beam current. The local electron density as well as the electron temperature, the floating potential and the plasma potential were measured and calculated by means of this characteristic.
Y1  - 2012
U6  - http://dx.doi.org/10.1063/1.3675874
SN  - 1089-7674 (E-Journal); 1070-664X (Print)
VL  - 19
IS  - 1
SP  - 1
EP  - 7
PB  - AIP Publishing
CY  - Melville, NY
ER  - 
TY  - JOUR
A1  - Reisgen, Uwe
A1  - Schleser, Markus
A1  - Abdurakhmanov, Aydemir
A1  - Turichin, Gleb
A1  - Valdaitseva, Elena
A1  - Bach, Friedrich-Wilhelm
A1  - Hassel, Thomas
A1  - Beniyashi, Alexander
T1  - Investigation of factors influencing the formation of weld defects in non-vacuum electron beam welding
JF  - The Paton welding journal
N2  - The influence of welding condition parameters and properties of material on formation of defects, such as humping and undercuts, in non-vacuum electron beam welding was investigated. The influence of separate welding parameters on the quality of welds was determined.
Y1  - 2012
SN  - 0957-798X
VL  - 2012
IS  - 2
SP  - 11
EP  - 18
PB  - Paton Publishing House
CY  - Kiev
ER  - 
TY  - JOUR
A1  - Reisgen, Uwe
A1  - Schleser, Markus
A1  - Feldmann, Martin
A1  - Pak, Daniel
A1  - Geßler, Achim
T1  - Kleben dünnwandiger Bauteile aus textilbewehrtem Beton
JF  - Schweissen und Schneiden : Fachzeitschrift für Schweißen und verwandte Verfahren
Y1  - 2008
SN  - 0036-7184
VL  - Bd. 60
IS  - H. 7/8
SP  - 408
EP  - 412
ER  - 
TY  - JOUR
A1  - Reisgen, Uwe
A1  - Schleser, Markus
A1  - Harms, Alexander
A1  - Schiebahn, Alexander
A1  - Naumov, Andreas
T1  - Erweiterung des Parameterfelds zum Rührreibschweißen mittels konduktiver Unterstützung
JF  - Schweissen und Schneiden : Fachzeitschrift für Schweißen und verwandte Verfahren
Y1  - 2011
SN  - 0036-7184
VL  - Bd. 63
IS  - H. 12
SP  - 710
EP  - 714
PB  - DVS-Media GmbH
CY  - Düsseldorf
ER  - 
TY  - JOUR
A1  - Reisgen, Uwe
A1  - Schleser, Markus
A1  - Harms, Alexander
A1  - Schiebahn, Alexander
A1  - Thiele, Regina
ED  - Kampker, Achim
T1  - Elektromobilität - Herausforderungen an die Fügetechnik
JF  - mobilität morgen - Magazin zu Mobilität und Elektromobilität
Y1  - 2011
VL  - Jg. 1
IS  - Nr. 2
SP  - 16
EP  - 17
ER  - 
TY  - JOUR
A1  - Reisgen, Uwe
A1  - Schleser, Markus
A1  - Jerabek, Jakub
A1  - Chudoba, Rostislav
T1  - Messung der Strahlqualität einer Elektronenstrahlanlage in Umgebungsatmosphäre
JF  - Materialwissenschaft und Werkstofftechnik
N2  - In den letzten Jahrzehnten hat das Elektronenstrahlschweißen, das bereits im größeren Maßstab verwendet wird, seine Fähigkeit als qualitatives Werkzeug für die Verbindung verschiedener Materialen nachgewiesen. Das Non Vacuum Electron Beam Welding (NV-EBW) hat zahlreiche Vorteile im Vergleich zum Elektronenstrahlschweißen im Vakuum, da man unter normalem Atmosphärendruck arbeiten kann. Im Hinblick auf die reproduzierbare Qualität, insbesondere im Bereich der Massen-Fertigung, ist die Kontrolle der Strahlparameter sowie deren Einfluss auf das Schweißergebnis von großer Bedeutung. Durch eine genaue Kenntnis der Strahlkenngrößen wie des Strahldurchmessers und der Leistungsdichteverteilung kann eine Aussage über die sich ausbildende Schweißnaht sowie die Schweißbaddynamik getroffen werden. Messungen der Strahlkenngrößen im Prozess erlauben insbesondere die Untersuchung von Humping-Effekten. In diesem Beitrag wird der Prozess der Elektronenstrahlvermessung unter atmosphärischen Bedingungen beschrieben. Es wird zudem die Abhängigkeit der Elektronenstrahlcharakteristika von den verschiedenen Prozessparametern dargestellt.
Y1  - 2010
SN  - 1521-4052
VL  - 41
IS  - 1
SP  - 45
EP  - 52
PB  - Wiley-VCH
CY  - Weinheim
ER  -