TY - CHAP A1 - Wiegner, Jonas A1 - Volker, Hanno A1 - Mainz, Fabian A1 - Backes, Andreas A1 - Löken, Michael A1 - Hüning, Felix T1 - Wiegand-effect-powered wireless IoT sensor node T2 - Sensoren und Messsysteme 2022 N2 - In this article we describe an Internet-of-Things sensing device with a wireless interface which is powered by the oftenoverlooked harvesting method of the Wiegand effect. The sensor can determine position, temperature or other resistively measurable quantities and can transmit the data via an ultra-low power ultra-wideband (UWB) data transmitter. With this approach we can energy-self-sufficiently acquire, process, and wirelessly transmit data in a pulsed operation. A proof-of-concept system was built up to prove the feasibility of the approach. The energy consumption of the system is analyzed and traced back in detail to the individual components, compared to the generated energy and processed to identify further optimization options. Based on the proof-of-concept, an application demonstrator was developed. Finally, we point out possible use cases. Y1 - 2022 SN - 978-3-8007-5835-7 SP - 255 EP - 260 PB - VDE Verlag GmbH CY - Berlin ER - TY - JOUR A1 - Wiegner, Jonas A1 - Volker, Hanno A1 - Mainz, Fabian A1 - Backes, Andreas A1 - Loeken, Michael A1 - Hüning, Felix T1 - Energy analysis of a wireless sensor node powered by a Wiegand sensor JF - Journal of Sensors and Sensor Systems (JSSS) N2 - This article describes an Internet of things (IoT) sensing device with a wireless interface which is powered by the energy-harvesting method of the Wiegand effect. The Wiegand effect, in contrast to continuous sources like photovoltaic or thermal harvesters, provides small amounts of energy discontinuously in pulsed mode. To enable an energy-self-sufficient operation of the sensing device with this pulsed energy source, the output energy of the Wiegand generator is maximized. This energy is used to power up the system and to acquire and process data like position, temperature or other resistively measurable quantities as well as transmit these data via an ultra-low-power ultra-wideband (UWB) data transmitter. A proof-of-concept system was built to prove the feasibility of the approach. The energy consumption of the system during start-up was analysed, traced back in detail to the individual components, compared to the generated energy and processed to identify further optimization options. Based on the proof of concept, an application prototype was developed. Y1 - 2023 U6 - http://dx.doi.org/10.5194/jsss-12-85-2023 SN - 2194-878X N1 - Corresponding author: Felix Hüning VL - 12 IS - 1 SP - 85 EP - 92 PB - Copernicus Publ. CY - Göttingen ER - TY - GEN A1 - Wiegner, J. A1 - Volker, H. A1 - Mainz, F. A1 - Backes, A. A1 - Löken, M. A1 - Hüning, Felix T1 - Wiegand-Effect-Powered Wireless IT Sensor Node N2 - With the growing interest in small distributed sensors for the “Internet of Things”, more attention is being paid to energy harvesting techologies. Reducing or eliminating the need for external power sources or batteries make devices more self-sufficient, more reliable, and reduces maintenance requirements. The Wiegand effect is a proven technology for harvesting small amounts of electrical power from mechanical motion. Y1 - 2022 N1 - PSMA International Energy Harvesting Workshop ~ 5-7 April 2022, Raleigh, NC, USA ER - TY - CHAP A1 - Wallnöfer, Armin A1 - Drath, Rainer A1 - Hüning, Felix T1 - Was ist Funktionales Engineering? Einordnung, Definition, Randbedingungen T2 - Automation 2015 : 16. Branchentreff der Mess- und Automatisierungstechnik, 11. und 12. Juni 2015, Baden-Baden / VDI/VDE-Gesellschaft Mess- und Automatisierungstechnik Y1 - 2015 SN - 978-3-18-092258-4 PB - VDI-Verl. CY - Düsseldorf ER - TY - CHAP A1 - Rebel, Sören A1 - Hüning, Felix A1 - Scholl, Ingrid A1 - Ferrein, Alexander T1 - MQOne: Low-cost design for a rugged-terrain robot platform T2 - Intelligent robotics and applications : 8th International Conference, ICIRA 2015, Portsmouth, UK, August 24-27, 2015, Proceedings, Part II (Lecture notes in computer science : vol. 9245) N2 - Rugged terrain robot designs are important for field robotics missions. A number of commercial platforms are available, however, at an impressive price. In this paper, we describe the hardware and software component of a low-cost wheeled rugged-terrain robot. The robot is based on an electric children quad bike and is modified to be driven by wire. In terms of climbing properties, operation time and payload it can compete with some of the commercially available platforms, but at a far lower price. Y1 - 2015 SN - 978-3-319-22875-4 (print) ; 978-3-319-22876-1 (E-Book) U6 - http://dx.doi.org/10.1007/978-3-319-22876-1_19 SP - 209 EP - 221 PB - Springer CY - Cham ER - TY - CHAP A1 - Rao, Deepak A1 - Pathrose, Plato A1 - Hüning, Felix A1 - Sid, Jithin T1 - An Approach for Validating Safety of Perception Software in Autonomous Driving Systems T2 - Model-Based Safety and Assessment: 6th International Symposium, IMBSA 2019, Thessaloniki, Greece, October 16–18, 2019, Proceedings N2 - The increasing complexity of Advanced Driver Assistance Systems (ADAS) presents a challenging task to validate safe and reliable performance of these systems under varied conditions. The test and validation of ADAS/AD with real test drives, although important, involves huge costs and time. Simulation tools provide an alternative with the added advantage of reproducibility but often use ideal sensors, which do not reflect real sensor output accurately. This paper presents a new validation methodology using fault injection, as recommended by the ISO 26262 standard, to test software and system robustness. In our work, we investigated and developed a tool capable of inserting faults at different software and system levels to verify its robustness. The scope of this paper is to cover the fault injection test for the Visteon’s DriveCore™ system, a centralized domain controller for Autonomous driving which is sensor agnostic and SoC agnostic. With this new approach, the validation of safety monitoring functionality and its behavior can be tested using real-world data instead of synthetic data from simulation tools resulting in having better confidence in system performance before proceeding with in-vehicle testing. KW - Advanced driver assistance systems (ADAS/AD) KW - ISO 26262 KW - Safety-critical systems validation KW - Safety of the intended functionality (SOTIF) Y1 - 2019 SN - 978-3-030-32872-6 U6 - http://dx.doi.org/10.1007/978-3-030-32872-6_20 SP - 303 EP - 316 PB - Springer CY - Cham ER - TY - CHAP A1 - Ostkotte, Sebastian A1 - Peters, Constantin A1 - Hüning, Felix A1 - Bragard, Michael T1 - Design, implementation and verification of an rotational incremental position encoder based on the magnetic Wiegand effect T2 - 2022 ELEKTRO (ELEKTRO) N2 - This paper covers the use of the magnetic Wiegand effect to design an innovative incremental encoder. First, a theoretical design is given, followed by an estimation of the achievable accuracy and an optimization in open-loop operation. Finally, a successful experimental verification is presented. For this purpose, a permanent magnet synchronous machine is controlled in a field-oriented manner, using the angle information of the prototype. KW - Position Encoder KW - Rotational Encoder KW - Wiegand Effect KW - Angle Sensor KW - Incremental Encoder Y1 - 2022 SN - 978-1-6654-6726-1 SN - 978-1-6654-6727-8 U6 - http://dx.doi.org/10.1109/ELEKTRO53996.2022.9803477 SN - 2691-0616 N1 - 2022 ELEKTRO (ELEKTRO), 23-26 Mai 2022, Krakow, Poland. PB - IEEE ER - TY - JOUR A1 - Kowalewski, Paul A1 - Bragard, Michael A1 - Hüning, Felix A1 - De Doncker, Rik W. T1 - An inexpensive Wiegand-sensor-based rotary encoder without rotating magnets for use in electrical drives JF - IEEE Transactions on Instrumentation and Measurement N2 - This paper introduces an inexpensive Wiegand-sensor-based rotary encoder that avoids rotating magnets and is suitable for electrical-drive applications. So far, Wiegand-sensor-based encoders usually include a magnetic pole wheel with rotating permanent magnets. These encoders combine the disadvantages of an increased magnet demand and a limited maximal speed due to the centripetal force acting on the rotating magnets. The proposed approach reduces the total demand of permanent magnets drastically. Moreover, the rotating part is manufacturable from a single piece of steel, which makes it very robust and cheap. This work presents the theoretical operating principle of the proposed approach and validates its benefits on a hardware prototype. The presented proof-of-concept prototype achieves a mechanical resolution of 4.5 ° by using only 4 permanent magnets, 2Wiegand sensors and a rotating steel gear wheel with 20 teeth. KW - Rotary encoder KW - Wiegand sensor Y1 - 2023 U6 - http://dx.doi.org/10.1109/TIM.2023.3326166 SN - 0018-9456 (Print) SN - 1557-9662 (Online) N1 - Early Access SP - 10 Seiten PB - IEEE ER - TY - RPRT A1 - Jaekel, C. A1 - Klein, C. A1 - Barth, R. A1 - Roskos, H. A1 - Kyas, G. A1 - Schroeer, M. A1 - Hüning, Felix T1 - Dynamik von Nichtgleichgewichtszustaenden in Hochtemperatursupraleitern Abschlussbericht N2 - Im Projekt wurden mit Hilfe zeitaufgeloester optischer Messtechniken Relaxations-Dynamiken von optisch angeregten Ladungstraegern und Hochfrequenzeigenschaften von Hochtemperatursupraleitern untersucht. Oberhalb der Sprungtemperatur wurden die Elektron-Phonon-Kopplungskonstanten fuer YBCO und BSCCO bestimmt. Dabei wurde erstmalig ein direkter Zusammenhang zwischen der Sprungtemperatur und der Kopplungstaerke gefunden. Der Kopplungsmechanismus enthaelt sowohl phononische als auch elektronische (spindynamische) Anteile. Unterhalb von T_c wird die Dynamik durch Aufbrechen und Rekombination von Cooper-Paaren bestimmt. Bei den Arbeiten zu den kohaerenten Phononen wurde ein Modell entwickelt, das das 'Anwerfen' der Phononen und das Amplitudenverhalten unterhalb der Sprungtemperatur erklaert. Als begleitende Untersuchungen wurden breitbandige Hochfrequenz-Messungen vorgenommen. Die Methode erlaubt die Untersuchung von Ladungstraegerdichten und von Streumechanismen. Erstmalig wurde in verspannten YBCO-Duennfilmen eine starke temperaturabhaengige Resonanz-Absorption beobachtet, die als Josephson-Plasmaresonanz an intrinsischen Kontakten identifiziert werden konnte. Die Nutzbarkeit dieser Kontakte fuer Bauelemente wurde durch einen Mikrowellendetektor demonstriert. Durch den Nachweis von emittierter gepulster Strahlung aus einer stromdurchflossenen supraleitenden Bruecke nach optischer Anregung wurde erstmals die Einsatzmoeglichkeit von HTSL fuer schnelle optische Schalter demonstriert. Es wurde gezeigt, dass die Schaltgeschwindigkeit eine direkte Folge der Ladungstraegerdynamik ist. T2 - Dynamics of non-equilibrium states in HTSC. Final report KW - Relaxation KW - Phonons KW - Calcium oxides KW - Electron-phonon coupling Y1 - 1996 N1 - Foerderkennzeichen BMBF 13N6288; TRN: DE97FD184 ER - TY - JOUR A1 - Hüning, Felix A1 - Wilke, I. A1 - Nakielski, G. A1 - Kotzler, J. T1 - Dynamic conductivity of YBCO thin films from low to very high frequencies / Wilke, I. ; Nakielski, G. ; Kotzler, J. ; Subke, K. O. ; Jaekel, C. ; Hüning, F. ; Roskos, H. G. ; Kurz, Heinrich JF - Applied superconductivity 1997 : proceedings of EUCAS 1997, the Third European Conference on Applied Superconductivity, held in the Netherlands, 30 June - 3 July 1997 / ed. by H. Rogalla Y1 - 1997 SN - 0-7503-0487-1 N1 - Institute of Physics conference series 158 SP - 121 EP - 124 PB - IOP CY - Bristol ER - TY - CHAP A1 - Hüning, Felix A1 - Wache, Franz-Josef A1 - Magiera, David T1 - Redundant bus systems using dual-mode radio T2 - Proceedings of Sixth International Congress on Information and Communication Technology N2 - Communication via serial bus systems, like CAN, plays an important role for all kinds of embedded electronic and mechatronic systems. To cope up with the requirements for functional safety of safety-critical applications, there is a need to enhance the safety features of the communication systems. One measure to achieve a more robust communication is to add redundant data transmission path to the applications. In general, the communication of real-time embedded systems like automotive applications is tethered, and the redundant data transmission lines are also tethered, increasing the size of the wiring harness and the weight of the system. A radio link is preferred as a redundant transmission line as it uses a complementary transmission medium compared to the wired solution and in addition reduces wiring harness size and weight. Standard wireless links like Wi-Fi or Bluetooth cannot meet the requirements for real-time capability with regard to bus communication. Using the new dual-mode radio enables a redundant transmission line meeting all requirements with regard to real-time capability, robustness and transparency for the data bus. In addition, it provides a complementary transmission medium with regard to commonly used tethered links. A CAN bus system is used to demonstrate the redundant data transfer via tethered and wireless CAN. Y1 - 2021 SN - 978-981-16-2379-0 SN - 978-981-16-2380-6 U6 - http://dx.doi.org/10.1007/978-981-16-2380-6_73 N1 - Proceedings of Sixth International Congress on Information and Communication Technology, ICICT 2021, Brunel University, London, February 25–26, 2021 SP - 835 EP - 842 PB - Springer CY - Singapore ER - TY - CHAP A1 - Hüning, Felix A1 - Stüttgen, Marcel T1 - Work in Progress: Interdisciplinary projects in times of COVID-19 crisis – challenges, risks and chances T2 - 2021 IEEE Global Engineering Education Conference (EDUCON) Y1 - 2021 U6 - http://dx.doi.org/10.1109/EDUCON46332.2021.9454006 SP - 1175 EP - 1179 ER - TY - JOUR A1 - Hüning, Felix A1 - Sparta, K. A1 - Redhammer, G. J. A1 - Roussel, P. T1 - Structural Phase Transition in the 2D Spin Dimer Compound SrCu2(BO3)2 / Sparta, K. ; Redhammer, G. J. ; Roussel, P. ; Heger, G. ; Roth, G. ; Ionescu, A. Lemmens, P. ; Grove, M. ; Güntherrodt, G. ; Hüning, F. ; Lueken, H. ; Kageyama, H. ; Onizuka, K ; Ueda JF - The European Physical Journal B - Condensed Matter and Complex Systems. 19 (2001), H. 4 Y1 - 2001 SN - 1434-6036 SP - 507 EP - 516 PB - - ER - TY - CHAP A1 - Hüning, Felix A1 - Mund, Cindy T1 - Integration of agile development in standard labs T2 - 51st Annual Conference of the European Society for Engineering Education (SEFI) N2 - In addition to the technical content, modern courses at university should also teach professional skills to enhance the competencies of students towards their future work. The competency driven approach including technical as well as professional skills makes it necessary to find a suitable way for the integration into the corresponding module in a scalable and flexible manner. Agile development, for example, is essential for the development of modern systems and applications and makes use of dedicated professional skills of the team members, like structured group dynamics and communication, to enable the fast and reliable development. This paper presents an easy to integrate and flexible approach to integrate Scrum, an agile development method, into the lab of an existing module. Due to the different role models of Scrum the students have an individual learning success, gain valuable insight into modern system development and strengthen their communication and organization skills. The approach is implemented and evaluated in the module Vehicle Systems, but it can be transferred easily to other technical courses as well. The evaluation of the implementation considers feedback of all stakeholders, students, supervisor and lecturers, and monitors the observations during project lifetime. KW - professional skills KW - active learning KW - lab work KW - Agile development Y1 - 2023 U6 - http://dx.doi.org/10.21427/NK4Z-WS73 N1 - 51st Annual Conference of the European Society for Engineering Education, Technological University Dublin 10th-14th September, 2023 ER - TY - JOUR A1 - Hüning, Felix A1 - Luken, Heiko A1 - Schilder, Herbert A1 - Eifert, Thomas T1 - Magnetochemistry: Compounds and Concepts / Lueken, Heiko ; Schilder, Herbert ; Eifert, Thomas ; Handrick, Klaus ; Hüning, Felix JF - Advances in Solid State Physics. 201 (2001) Y1 - 2001 SP - 515 EP - 532 PB - - ER - TY - JOUR A1 - Hüning, Felix A1 - Leineweber, A. A1 - Jacobs, H. A1 - Lueken, H. T1 - ε-Fe3N: magnetic structure, magnetization and temperature dependent disorder of nitrogen / Leineweber, A. ; Jacobs, H. ; Hüning, F. ; Lueken, H. ; Schilder, H. ; Kockelmann, W. JF - Journal of Alloys and Compounds. 288 (1999), H. 1-2 N2 - ε-Fe3N has been investigated by time-of-flight neutron diffraction (temperature range 4.2–618 K) and SQUID magnetometry (2–700 K, B≤5 T). A ferromagnetic spin structure is observed with magnetic moments oriented perpendicular to the c-axis of the hexagonal nuclear structure. The magnetic saturation moment of iron is 2.2 μB at 4.2 K from neutron diffraction and 2.0 μB from magnetic measurements and decreases in a Brillouin-like manner on heating to TC=575 K. Above 450 K an increasing but reversible disorder of the nitrogen partial structure is observed. Y1 - 1999 SN - 1873-4669 VL - 288 IS - 1-2 SP - 79 EP - 87 PB - Elsevier CY - Amsterdam ER - TY - JOUR A1 - Hüning, Felix A1 - Leineweber, A. A1 - Jacobs, H. A1 - Lueken, H. T1 - Nitrogen Ordering and ferromagnetic properties of -Fe3N1+x (0.10  x  0.39) and -Fe3(N0.80C0.20)1.38 / Leineweber, A. ; Jacobs, H. ; Hüning, F. ; Lueken, H. ; Kockelmann, W. JF - Journal of Alloys and Compounds. 316 (2001), H. 1-2 Y1 - 2001 SN - 1873-4669 SP - 21 EP - 38 PB - - ER - TY - JOUR A1 - Hüning, Felix A1 - Jaekel, C. A1 - Francois, I. A1 - Kyas, G. T1 - Microwave surface impedance measurements on high-Tc superconductors / Jaekel, C. ; Francois, I. ; Kyas, G. ; Hüning, F. ; Roskos, H. G. ; Borghs, G. ; Kurz, H. JF - Czechoslovak Journal of Physics. 46 (1996), H. Suppl. 2 Y1 - 1996 SN - 1572-9486 IS - 46 SP - 1117 EP - 1118 PB - Springer Science+Business Media CY - Dordrecht ER - TY - JOUR A1 - Hüning, Felix A1 - Hillgärtner, Michael A1 - Reke, Michael T1 - Rolling Labs – Teaching Vehicle Electronics from the Beginning JF - International Journal of Engineering Pedagogy (iJEP) Y1 - 2019 U6 - http://dx.doi.org/10.3991/ijep.v9i1.9241 SN - 2192-4880 VL - 9 IS - 1 SP - 34 EP - 49 ER - TY - JOUR A1 - Hüning, Felix A1 - Heuermann, Holger A1 - Wache, Franz-Josef A1 - Jajo, Rami Audisho T1 - A new wireless sensor interface using dual-mode radio JF - Journal of Sensors and Sensor Systems : JSSS N2 - The integration of sensors is one of the major tasks in embedded, control and “internet of things” (IoT) applications. For the integration mainly digital interfaces are used, starting from rather simple pulse-width modulation (PWM) interface to more complex interfaces like CAN (Controller Area Network). Even though these interfaces are tethered by definition, a wireless realization is highly welcome in many applications to reduce cable and connector cost, increase the flexibility and realize new emerging applications like wireless control systems. Currently used wireless solutions like Bluetooth, WirelessHART or IO-Link Wireless use dedicated communication standards and corresponding higher protocol layers to realize the wireless communication. Due to the complexity of the communication and the protocol handling, additional latency and jitter are introduced to the data communication that can meet the requirements for many applications. Even though tunnelling of other bus data like CAN data is generally also possible the latency and jitter prevent the tunnelling from being transparent for the bus system. Therefore a new basic technology based on dual-mode radio is used to realize a wireless communication on the physical layer only, enabling a reliable and real-time data transfer. As this system operates on the physical layer it is independent of any higher layers of the OSI (open systems interconnection) model. Hence it can be used for several different communication systems to replace the tethered physical layer. A prototype is developed and tested for real-time wireless PWM, SENT (single-edge nibble transmission) and CAN data transfer with very low latency and jitter. Y1 - 2018 U6 - http://dx.doi.org/10.5194/jsss-7-507-2018 VL - Volume 7 IS - 2 SP - 507 EP - 515 PB - Copernicus Publ. CY - Göttingen ER -