TY - JOUR A1 - Michaux, F. A1 - Mattern, P. A1 - Kallweit, Stephan T1 - RoboPIV: how robotics enable PIV on a large industrial scale JF - Measurement Science and Technology N2 - This work demonstrates how the interaction between particle image velocimetry (PIV) and robotics can massively increase measurement efficiency. The interdisciplinary approach is shown using the complex example of an automated, large scale, industrial environment: a typical automotive wind tunnel application. Both the high degree of flexibility in choosing the measurement region and the complete automation of stereo PIV measurements are presented. The setup consists of a combination of three robots, individually used as a 6D traversing unit for the laser illumination system as well as for each of the two cameras. Synchronised movements in the same reference frame are realised through a master-slave setup with a single interface to the user. By integrating the interface into the standard wind tunnel management system, a single measurement plane or a predefined sequence of several planes can be requested through a single trigger event, providing the resulting vector fields within minutes. In this paper, a brief overview on the demands of large scale industrial PIV and the existing solutions is given. Afterwards, the concept of RoboPIV is introduced as a new approach. In a first step, the usability of a selection of commercially available robot arms is analysed. The challenges of pose uncertainty and importance of absolute accuracy are demonstrated through comparative measurements, explaining the individual pros and cons of the analysed systems. Subsequently, the advantage of integrating RoboPIV directly into the existing wind tunnel management system is shown on basis of a typical measurement sequence. In a final step, a practical measurement procedure, including post-processing, is given by using real data and results. Ultimately, the benefits of high automation are demonstrated, leading to a drastic reduction in necessary measurement time compared to non-automated systems, thus massively increasing the efficiency of PIV measurements. Y1 - 2018 U6 - https://doi.org/10.1088/1361-6501/aab5c1 SN - 1361-6501 N1 - Special Section on the 12th International Symposium on Particle Image Velocimetry (PIV 2017) VL - 29 IS - 7 SP - 074009 PB - IOP CY - Bristol ER - TY - JOUR A1 - Kämper, Klaus-Peter A1 - Pappas, D. P. A1 - Hopster, H. T1 - Reversible transition between perpendicular and in-plane magnetization in ultrathin films. Pappas, D. P.; Kämper, K.-P.; Hopster, H. JF - Physical Review Letters. 64 (1990), H. 26 Y1 - 1990 SN - 1079-7114 SP - 3179 EP - 3182 ER - TY - JOUR A1 - Willms, Herbert A1 - Beer, Stefan A1 - Fröhlke, K. A1 - Haidn, O.J. T1 - Regelung eines Wasserstoff-/Sauerstoff-Dampferzeugers mit Hilfe eines modifizierten Zirkondioxid-Sensors Y1 - 1993 N1 - Report: Deutsche Forschungsanstalt für Luft- und Raumfahrt, EN-CA/E (1993) Seite 1-17 (17 Seiten, 14 Bilder, 2 Tabellen, 14 Quellen) ER - TY - JOUR A1 - Willms, Herbert T1 - Regelung eines H2/O2-Dampferzeugers mit Hilfe eines modifizierten Zirkondioxid-Sensors JF - Chemie Ingenieur Technik Y1 - 1993 SN - 0009-286X VL - 65 IS - 8 SP - 954 EP - 956 PB - Wiley-VCH CY - Weinheim ER - TY - JOUR A1 - Willms, Herbert A1 - Beer, Stefan T1 - Regelung eines H(IND 2)/O(IND 2)-Dampferzeugers Y1 - 1992 SN - 0939-2963 N1 - Report: Regelung eines H(IND 2)/O(IND 2)-Dampferzeugers, Deutsche Forschungsanstalt fuer Luft- und Raumfahrt e.V. (DLR), Hardthausen am Kocher (DE). Inst. fuer Chemische Antriebe und Verfahrenstechnik, Sep 1992, (116 S. Gesamtumfang) ER - TY - JOUR A1 - Baatz, Udo A1 - Butz, Hans-Werner T1 - Rechnerunterstuetztes Konstruieren mit Symbolen JF - TZ für praktische Metallbearbeitung Y1 - 1972 SN - 0177-8900 VL - 66 IS - 9 SP - 366 EP - 370 PB - Grossmann CY - Stuttgart ER - TY - JOUR A1 - Heinrichs, Horst A1 - Weck, M. A1 - Heimann, A. T1 - Rechnerunterstuetzte Aufbereitung von Finite-Elemente-Rechenmodellen-Erfassung der Bauteilgeometrie JF - Industrieanzeiger. 99 (1977), H. 78 Y1 - 1977 SP - 1509 EP - 1512 ER - TY - JOUR A1 - Heinrichs, Horst A1 - Weck, M. T1 - Rechnerunterstuetzte Aufbereitung von Finite-Elemente-Rechenmodellen -Erstellen der FEM-Netzwerke JF - Industrieanzeiger. 99 (1977), H. 102 Y1 - 1977 SP - 2059 EP - 2061 ER - TY - JOUR A1 - Starke, Günther A1 - Kremer-Wasmuth, S. T1 - Rechnergestützte Prozeßkontrolle und -dokumentation zur Qualitätsüberwachung beim Schweißen JF - Qualitätsorientierte Schweißtechnik als Wettbewerbsfaktor, DVS-Berichte. 196 (1999) Y1 - 1999 SN - 0418-9639 N1 - Report SP - 49 EP - 52 ER - TY - JOUR A1 - Leidinger, Rafael A1 - Noisten, Thomas A1 - Wollert, Jörg T1 - Realtime automation networks in moVing industrial environments JF - Journal of systemics, cybernetics and informatics N2 - The radio-based wireless data communication has made the realization of new technical solutions possible in many fields of the automation technology (AT). For about ten years, a constant disproportionate growth of wireless technologies can be observed in the automation technology. However, it shows that especially for the AT, conventional technologies of office automation are unsuitable and/or not manageable. The employment of mobile services in the industrial automation technology has the potential of significant cost and time savings. This leads to an increased productivity in various fields of the AT, for example in the factory and process automation or in production logistics. In this paper technologies and solutions for an automation-suited supply of mobile wireless services will be introduced under the criteria of real time suitability, IT-security and service orientation. Emphasis will be put on the investigation and development of wireless convergence layers for different radio technologies, on the central provision of support services for an easy-to-use, central, backup enabled management of combined wired / wireless networks and on the study on integrability in a Profinet real-time Ethernet network. KW - PROFINET KW - Distributed Control Systems, KW - Industrial Automation Technology, KW - 802.15.4 KW - Bluetooth KW - Wireless Networks Y1 - 2012 SN - 1690-4532 VL - Vol. 10 IS - Iss. 2 SP - 52 EP - 56 PB - IIIC CY - Orlando ER - TY - JOUR A1 - Grundmann, Reinhard T1 - Raumlufttechnik, Lüftungstechnik, Klimatechnik, Lärm JF - HLH - Zeitschrift für Heizung, Lüftung, Klimatechnik, Haustechnik. 55 (2004), H. 12 Y1 - 2004 SN - 0017-9906 SP - 46 EP - 49 ER - TY - JOUR A1 - Gebhardt, Andreas T1 - Rapid Tooling. Der schnelle Weg zum Spritzgießwerkzeug. JF - Kunststoffe, München. 88 (1998), H. 11 Y1 - 1998 SN - 0023-5563 SP - 1992 EP - 2000 ER - TY - JOUR A1 - Gebhardt, Andreas A1 - Schmachtenberg, E. T1 - Rapid Prototyping und Tooling Y1 - 1996 N1 - Konferenz-Einzelbericht : 7. Würzburger Werkzeugtage, Produktivitätsverbesserungen, neue Technologien, Fachtagung, Würzburg, DE, 24.-25. Sep, 1996 SP - 1 EP - 20 ER - TY - JOUR A1 - Gebhardt, Andreas T1 - Rapid Prototyping and PIV Y1 - 2001 N1 - Workshop on Industrial Applications of Particle Image Velocimetry <2001, Köln> ER - TY - JOUR A1 - Gebhardt, Andreas T1 - Rapid Prototyping : Grundlagen, Verfahren und Einsatzkriterien für die industrielle Praxis JF - Konstruieren mit Kunststoffen. - 3. Aufl. Y1 - 2003 SN - 3-935065-13-2 N1 - Kap. 7 PB - Springer -VDI-Verl. CY - Düsseldorf ER - TY - JOUR A1 - Gebhardt, Andreas T1 - Rapid Prototyping - Laser-gestützte Revolution der Produktentwicklung. Teil I JF - Laser Magazin (1996) Y1 - 1996 SN - 0945-8875 SP - 6 EP - 9 ER - TY - JOUR A1 - Gebhardt, Andreas T1 - Rapid Prototyping JF - Landolt-Börnstein - Group VIII Advanced Materials and Technologies‡Vol. 1 Laser Physics and Applications‡Subvol. C Laser Applications / authors: Bäuerle, D. ... Y1 - 2004 SN - 3-540-00105-0 SP - 105 EP - 123 PB - Heidelberg CY - Springer ER - TY - JOUR A1 - Franzen, Julius A1 - Pinders, Erik A1 - Pfaff, Raphael A1 - Enning, Manfred T1 - RailCrowd’s virtual fleets: Make most of your asset data JF - Deine Bahn N2 - For smaller railway operators or those with a diverse fleet, it can be difficult to collect sufficient data to improve maintenance programs. At the same time, new rules such as entity in charge of maintenance – ECM – regulations impose an additional workload by requiring a dedicated maintenance management system and specific reports. The RailCrowd platform sets out to facilitate compliance with ECM and similar regulations while at the same time pooling anonymised fleet data across operators to form virtual fleets, providing greater data insights. Y1 - 2018 SN - 0948-7263 IS - 9 SP - 11 EP - 13 PB - Bahn-Fachverlag CY - Berlin ER - TY - JOUR A1 - Kunkel, Maximilian Hugo A1 - Gebhardt, Andreas A1 - Mpofu, Khumbulani A1 - Kallweit, Stephan T1 - Quality assurance in metal powder bed fusion via deep-learning-based image classification JF - Rapid Prototyping Journal Y1 - 2019 U6 - https://doi.org/10.1108/RPJ-03-2019-0066 SN - 1355-2546 VL - 26 IS - 2 SP - 259 EP - 266 ER - TY - JOUR A1 - Starke, Günther A1 - Drews, P. T1 - Qualitaetssicherung in der automatisierten schweisstechnischen Fertigung durch Einsatz von Sensoren JF - Technisches Messen tm. 50 (1983), H. 12 Y1 - 1983 SN - 0171-8096 SP - 467 EP - 473 ER -