TY - JOUR A1 - Reisgen, Uwe A1 - Schleser, Markus A1 - Mokrov, Oleg A1 - Ahmed, Essam T1 - Shielding gas influences on laser weldability of tailored blanks of advanced automotive steels JF - Applied surface science N2 - The effects of shielding gas types and flow rates on CO2 laser weldability of DP600/TRIP700 steel sheets were studied in this work. The evaluated shielding gases were helium (He), argon (Ar) and different mixtures of He and Ar. Weld penetration, tensile strength and formability (Erichsen test) of laser welds were found to be strongly dependent upon the shielding gas types. The ability of shielding gas in removing plasma plume and thus increasing weld penetration is believed to be closely related to ionization potential and atomic weight which determine the period of plasma formation and disappearance. It was found that the higher helium shielding gas flow rate, the deeper weld penetration and the lower weld width. Y1 - 2010 U6 - http://dx.doi.org/10.1016/j.apsusc.2010.08.042 SN - 0169-4332 (E-Journal); 0169-4332 (Print) VL - 257 IS - 5 SP - 1401 EP - 1406 PB - Elsevier CY - Amsterdam ER - TY - JOUR A1 - Gebhardt, Andreas A1 - Mathar, W. A1 - Plum, H.-D. T1 - SFM-System Stereolithographie und selektives Lasersintern im Vergleich Y1 - 1994 N1 - Konferenz-Einzelbericht : Solid freeform manufacturing/Intelligente Produktionssysteme, Internationale Konferenz, Dresden, DE, 29.-30.9.1994 SP - 85 EP - 95 ER - TY - JOUR A1 - Kämper, Klaus-Peter A1 - Berg, U. A1 - Begemann, M. A1 - Hagemann, B. (u.a.) T1 - Series production and testing of a micro motor. Serienfertigung und Prüfung eines Mikromotors JF - Actuator 98 : 6th International Conference on New Actuators ; 17 - 19 June, 1998, Bremen, Germany ; conference proceedings / ed.: Hubert Borgmann ... Y1 - 1998 SN - 3-933339-00-6 N1 - Konferenz-Einzelbericht: ACTUATOR, Internat. Conf. on New Actuators SP - 552 EP - 555 PB - Messe Bremen CY - Bremen ER - TY - JOUR A1 - Gebhardt, Andreas A1 - Mathar, W. A1 - Plum, H-D. A1 - Wolf, M. T1 - Serienqualität und -stückzahlen durch Abformprozesse Y1 - 1996 N1 - Konferenz-Einzelbericht : Produkt- und Prozeßentwicklung mit neuen Technologien, Intelligente Produktionssysteme - Solid Freeform Manufacturing, 4. Anwendertagung, Dresden, DE, 25.-26.09.1996 SP - 147 EP - 159 ER - TY - JOUR A1 - Starke, Günther A1 - Drews, P. T1 - Sensorik für das Schutzgasschweißen mit Robotern JF - DVS-Berichte. 143 (1992) Y1 - 1992 SN - 0418-9639 N1 - Konferenz-Einzelbericht SP - 62 EP - 66 ER - TY - JOUR A1 - Starke, Günther A1 - Drews, P. T1 - Sensoren in der Schweisstechnik JF - Die Umschau. 84 (1985), H. 5 Y1 - 1985 SN - 0041-6347 SP - 296 EP - 300 ER - TY - JOUR A1 - Starke, Günther A1 - Beckmann, L.-H. A1 - Rogos, J. A1 - Schmall, K-H. (u.a.) T1 - Sensoren in der automatisierten Schweisstechnik Y1 - 1987 N1 - Konferenz-Einzelbericht: Schweissen mit Robotern. Vortragsband zum Aachener Kolloquium, Schweissen mit Robotern, Aachen, 30.03.1987-31.03.1987 SP - 61 EP - 147 ER - TY - JOUR A1 - Starke, Günther T1 - Sensoren fuer Schutzgasschweissroboter: Problemstellung, Funktionsweise, Handhabung und Programmierung von praxiserprobten Systemen Y1 - 1986 N1 - Konferenz-Einzelbericht : Kommtech '86. 3. Int. Kongressmesse fuer Technischr Automation. ONLINE Ges., Essen, D, 13.-16.5.1986 SP - 1 EP - 22 ER - TY - JOUR A1 - Rieper, Harald A1 - Gebhardt, Andreas A1 - Stucker, Brent T1 - Selective Laser Melting of the Eutectic Silver-Copper Alloy Ag 28 wt % Cu JF - RTejournal - Forum für Rapid Technologie N2 - The aim of this work was to perform a detailed investigation of the use of Selective Laser Melting (SLM) technology to process eutectic silver-copper alloy Ag 28 wt. % Cu (also called AgCu28). The processing occurred with a Realizer SLM 50 desktop machine. The powder analysis (SEM-topography, EDX, particle distribution) was reported as well as the absorption rates for the near-infrared (NIR) spectrum. Microscope imaging showed the surface topography of the manufactured parts. Furthermore, microsections were conducted for the analysis of porosity. The Design of Experiments approach used the response surface method in order to model the statistical relationship between laser power, spot distance and pulse time. KW - SLM KW - Response Surface Method KW - Porositat KW - Eutectic Silver Copper alloy KW - Additive Manufacturing Y1 - 2016 U6 - http://nbn-resolving.de/urn/resolver.pl?nbn:de:0009-2-44141 SN - 1614-0923 VL - 13 ER - TY - JOUR A1 - Fateri, Miranda A1 - Gebhardt, Andreas T1 - Selective Laser Melting of Soda-Lime Glass Powder JF - International Journal of Applied Ceramic Technology Y1 - 2015 U6 - http://dx.doi.org/10.1111/ijac.12338 SN - 1744-7402 VL - 12 IS - 1 SP - 53 EP - 61 PB - Wiley-Blackwell CY - Oxford ER - TY - JOUR A1 - Hötter, Jan-Steffen A1 - Fateri, Miranda A1 - Gebhardt, Andreas T1 - Selective laser melting of metals: desktop machines open up new chances even for small companies JF - Advanced materials research N2 - Additive manufacturing (AM) of metal parts by using Selective Laser Melting (SLM) has become a powerful tool mostly in the area of automotive, aerospace engineering and others. Especially in the field of dentistry, jewelry and related branches that require individualized or even one-of-a-kind products, the direct digital manufacturing process opens up new ways of design and manufacturing. In these fields, mostly small and medium sized businesses (SME) are operating which do not have sufficient human and economic resources to invest in this technology. But to stay competitive, the application of AM can be regarded as a necessity. In this situation a new desktop machine (Realizer SLM 50) was introduced that cost about 1/3 of a shop floor SLM machine and promises small quality parts. To find out whether the machine really is an alternative for SMEs the University of Applied Science, Aachen, Germany, designed, build and optimized typical parts from the dentistry and the jewelry branches using CoCr and silver material, the latter being new with this application. The paper describes the SLM procedure and how to find and optimize the most important parameters. The test is accompanied by digital simulation in order to verify the build parameters and to plan future builds. The procedure is shown as well as the resulting parts made from CoCr and silver material. Y1 - 2012 U6 - http://dx.doi.org/10.4028/www.scientific.net/AMR.622-623.461 SN - 1662-8985 (E-Journal); 1022-6680 (Print) VL - 622-623 SP - 461 EP - 465 PB - Trans Tech Publ. CY - Baech ER - TY - JOUR A1 - Enning, Manfred A1 - Dolls, S. A1 - Brunberg, A. T1 - Selbsteinstellverfahren für Temperiervorrichtungen mit Außenverrohrung / Dolls, S. ; Enning, M. ; Brunberg, A. ; Abel, D. JF - Automation 2009 : Automatisierungskongress in Deutschland ; Kongress Baden-Baden, 16. und 17. Juni 2009 / VDI-VDE-Gesellschaft Mess- und Automatisierungstechnik Y1 - 2009 SN - 978-3-18-092067-2 N1 - Automatisierungskongress <2009, Baden-Baden> ; VDI-Berichte ; 2067 SP - 429 EP - 432 PB - VDI-Verl. CY - Düsseldorf ER - TY - JOUR A1 - Benner, Joachim T1 - Schwingungsbelastung von drehzahlgeregelten Antrieben mit Stromrichtermotoren JF - Antriebstechnik : Konstruktion, Entwicklung und Anwendung von Antrieben und Steuerungen ; Organ der Forschungsvereinigung Antriebstechnik e.V. Y1 - 1989 SN - 0341-2652 VL - 28 IS - 12 SP - 49 EP - 54 PB - Vereinigte Fachverl. CY - Mainz ER - TY - JOUR A1 - Starke, Günther A1 - Strunz, U. A1 - Spieß, C. T1 - Schweißprozeßparameteroptimierung mit Fuzzy-Logik JF - Schweißen und Schneiden. 47 (1995), H. 6 Y1 - 1995 SN - 0036-7184 SP - 494 EP - 503 ER - TY - JOUR A1 - Gebhardt, Andreas A1 - Guntermann, P. A1 - Häming, L. T1 - Schweißen mit dem Nd:YAG-Laser JF - Der Praktiker, Schweißen und Schneiden. 49 (1997), H. 4 Y1 - 1997 SN - 0554-9965 SP - 170 EP - 172 ER - TY - JOUR A1 - Gebhardt, Andreas T1 - Schnell und flexibel zur Kleinserie. Effizienzsteigerung bei der Realisierung von Komponenten und Teilsystemen JF - Ingenieur-Werkstoffe. 8 (1999), H. 3 Y1 - 1999 SN - 0935-5715 SP - 8 EP - 14 ER - TY - JOUR A1 - Wollert, Jörg T1 - Schlaue Produktion von smarten Autos : hinter der Smart-Produktion steckt ein innovatives Logistikkonzept JF - Technica Y1 - 1999 SN - 0040-866X VL - Bd. 48 IS - H. 4 SP - 20 EP - 23 ER - TY - JOUR A1 - Babilon, Katharina A1 - Wilbring, Daniela A1 - Tappert, Tim A1 - Pfaff, Raphael A1 - Enning, Manfred T1 - Schienenfahrzeugtechnik hands on – FH Aachen IMechE Railway Challenge JF - Ingenieurspiegel Y1 - 2018 SN - 1868-5919 IS - 2 SP - 20 EP - 22 PB - Public Verlag CY - Bingen ER - TY - JOUR A1 - Gebhardt, Andreas A1 - Brücker, Christoph A1 - Schmidt, Frank-Michael T1 - RP gestützte Herstellung komplexer transparenter Hohlräume für die Strömungsanalyse N2 - Die Berechnung der Durchströmung von Bauteilen ist gegenüber derjenigen von umströmten Bauteilen deutlich im Hintertreffen. Das liegt vor allem an der fehlenden Verfügbarkeit geeigneter optisch transparenter Modellkanäle für die experimentelle Analyse. Der Beitrag stellt ein Verfahren zur Herstellung transparenter durchströmter Geometrien auf der Basis generativ gefertigter Urmodelle vor. Damit können beliebig komplexe Innenströmungen optisch analysiert werden. Anhand von zwei Beispielen aus der Medizin, der Modellierung der oberen Atemwege und des Bronchialbaums, wird das Verfahren vorgeführt. Der generative Bauprozess mittels 3D-Printing wird beschrieben und die Abformung in transparentem Silikon gezeigt. Schließlich werden beispielhaft der Messaufbau und Ergebnisse der Anwendung vorgestellt. Das Verfahren bildet die Grundlage für die Analyse und Berechnung komplexer Innenströmungen und trägt somit zur Verbesserung zahlreicher technischer Anwendungen bei. N2 - Unlike the flow around technical products the interior flow is not understood very well. That’s mainly because of a lack of suitable transparent investigation tunnels that are needed to apply optical methods. The paper proposes a procedure to make precise complex hollow structures from a highly transparent material using masters from generative or Rapid Prototyping processes. Taking two examples from the medical field, the upper human airways and the bronchial tree, the entire process is shown. The 3D Printing build process is illustrated as well as the silicon casting process. Finally the measuring equipment is demonstrated and sample results are given. The process establishes the basis for the investigation and calculation of complex interior flow pattern and therefore contributes to a better understanding and consequently improvement of appropriate technical products. KW - Rapid prototyping KW - Rapid Prototyping KW - Strömungsanalyse KW - Innenströmung KW - Modellkanäle KW - 3D-Printing Y1 - 2005 ER - TY - JOUR A1 - Starke, Günther A1 - Ahlbehrendt, Norbert A1 - Bischoff, Rainer A1 - Melzer, Harald A1 - Sieber, Sven A1 - Senk, Burkhard A1 - Kramarczyk, Peter T1 - RoboTOOL. Technologien für den ortsflexiblen Einsatz von Robotern bei temporären Arbeitsaufgaben in der Fertigung JF - wt Werkstattstechnik online Y1 - 2009 SN - 1436-4980 VL - Bd. 99 IS - H. 9 SP - 661 EP - 670 ER -