TY - JOUR A1 - Harris, Isaac A1 - Kleefeld, Andreas T1 - The inverse scattering problem for a conductive boundary condition and transmission eigenvalues JF - Applicable Analysis N2 - In this paper, we consider the inverse scattering problem associated with an inhomogeneous media with a conductive boundary. In particular, we are interested in two problems that arise from this inverse problem: the inverse conductivity problem and the corresponding interior transmission eigenvalue problem. The inverse conductivity problem is to recover the conductive boundary parameter from the measured scattering data. We prove that the measured scatted data uniquely determine the conductivity parameter as well as describe a direct algorithm to recover the conductivity. The interior transmission eigenvalue problem is an eigenvalue problem associated with the inverse scattering of such materials. We investigate the convergence of the eigenvalues as the conductivity parameter tends to zero as well as prove existence and discreteness for the case of an absorbing media. Lastly, several numerical and analytical results support the theory and we show that the inside–outside duality method can be used to reconstruct the interior conductive eigenvalues. KW - Transmission eigenvalues KW - Conductive boundary condition KW - Inverse scattering Y1 - 2018 U6 - https://doi.org/10.1080/00036811.2018.1504028 SN - 1563-504X VL - 99 IS - 3 SP - 508 EP - 529 PB - Taylor & Francis CY - London ER - TY - GEN A1 - Engel, M. A1 - Bayer, H. A1 - Ulber, Roland A1 - Tippkötter, Nils T1 - Kommt es in Elektrofermentationen mit Clostridium acetobutylicum zu einer Eisenlimitierung? T2 - Chemie Ingenieur Technik N2 - Das strikt anaerobe Bakterium Clostridium acetobutylicum bildet die Lösemittel Aceton, Butanol und Ethanol (ABE-Fermentation). Im Fall einer Eisenlimitierung kommt es zusätzlich zu einer Riboflavinsekretion (RF), was durch die gelbe Färbung des Kulturüberstands erkennbar ist. In dieser Arbeit wurde beobachtet, dass während Elektrofermentationen mit C. acetobutylicum bei –600 mV eine gelbe Färbung auftritt. Es wurde deshalb untersucht, ob eine Eisenlimitierung im bio-elektrochemischen System (BES) vorliegt. Hierzu wurden die Flavinspezien bei Kultivierungen in Medien mit einer Eisenlimitierung bzw. mit ausreichend Eisen in Serumflaschen sowie im BES mit und ohne angelegtem Potenzial verglichen. In den Serumflaschenversuchen wurden RF und Flavinadenindinukleotid (FAD)-Konzentrationen von ‡ 20 mg L⁻¹ sowie Flavinmononukleotid (FMN)-Konzentrationen von ca. 5 mg L⁻¹ detektiert. Bei ausreichender Eisenverfügbarkeit hingegen wurden in den Serumflaschen fast keine Flavine sekretiert. Im BES bei –600 mV hingegen wurde auch in diesen Kulturüberständen FMN und FAD (1–5 mg L⁻¹ ),jedoch kein RF gemessen. Diese Ergebnisse zeigen, dass die Flavinbildung im BES mit angelegtem Potenzial nicht mit der Flavinbildung unter Eisenlimitierung in Serumflaschen korreliert. Andere Faktoren für eine mögliche Flavinbildung werden aktuell näher betrachtet. Y1 - 2018 U6 - https://doi.org/10.1002/cite.201855047 SN - 0009-286X SN - 1522-2640 (eISSN) N1 - ProcessNet-Jahrestagung und 33. DECHEMA-Jahrestagung der Biotechnologen 2018, 10. - 13. September 2018, Eurogress Aachen VL - 90 IS - 9 SP - 1154 PB - Wiley-VCH CY - Weinheim ER - TY - GEN A1 - Capitain, C. C. A1 - Lukeba, L. A1 - Ulber, Roland A1 - Tippkötter, Nils T1 - Biomimetische Klebstoffe aus Organosolv-Lignin T2 - Chemie Ingenieur Technik N2 - Aufgrund von EU-Regularien und Umweltinitiativen wächst der Markt für nachhaltige und abbaubare Klebstoffe stetig. Organosolv (OS)-Lignin ist ein kommerziell wenig ertragreicher Nebenstrom der Lignocellulose-Bioraffinerie. Durch das "Nachahmen" der Adhäsionseigenschaften mit strukturverwandten Muschel-Aminosäuren soll OS-Lignin in einen starkes, vollständig biobasiertes Adhäsiv umgewandelt werden. Funktionsweisend für die Adhäsion des Muschelklebstoffes ist die Catecholgruppe der Aminosäure L-DOPA. Die laccase-katalysierte Polymerisationsreaktion von Lignin und L-DOPA ist schwierig zu kontrollieren, da L-DOPA eine Ringschlussreaktion eingeht. Stattdessen wurde eine zweistufige Reaktion mit einem Diamin als Ankermolekül etabliert. Die Catecholgruppe, die im zweiten Schritt enzymatisch an das Lignin-Amin gebunden wird, kann durch Komplexbildung mit Fe(III)-Ionen sowohl zur Adhäsion als auch zur Kohäsion des Klebstoffes beitragen. Der Lignin-Catechol-Klebstoff ist frei von petrochemischen Chemikalien und biologisch abbaubar. In ersten Stirnzugversuchen konnte eine Haftkraft von 0,3 MPa erreicht werden. Y1 - 2018 U6 - https://doi.org/10.1002/cite.201855076 SN - 0009-286X SN - 1522-2640 (eISSN) N1 - ProcessNet-Jahrestagung und 33. DECHEMA-Jahrestagung der Biotechnologen 2018, 10. - 13. September 2018, Eurogress Aachen VL - 90 IS - 9 SP - 1167 PB - Wiley-VCH CY - Weinheim ER - TY - GEN A1 - Ross-Jones, J. A1 - Teumer, T. A1 - Capitain, C. A1 - Tippkötter, Nils A1 - Krause, M. J. A1 - Methner, F.-J. A1 - Rädle, M. T1 - Analytical methods for in-line characterization of beer haze T2 - Trends in Brewing N2 - In most beers, producers strive to minimize haze to maximize visual appeal. To detect the formation of particulates, a measurement system for sub-micron particles is required. Beer haze is naturally occurring, composed of protein or polyphenol particles; in their early stage of growth their size is smaller than 2 µm. Microscopy analysis is time and resource intensive; alternatively, backscattering is an inexpensive option for detecting particle sizes of interest. Y1 - 2018 N1 - Trends in Brewing, April 8 –12, 2018, Ghent, Belgium ER - TY - RPRT A1 - Drescher, Hans Paul T1 - The irreversible thermodynamic’s theorem of minimum entropy production applied to the laminar and the turbulent Couette flow N2 - Analyzing thermodynamic non-equilibrium processes, like the laminar and turbulent fluid flow, the dissipation is a key parameter with a characteristic minimum condition. That is applied to characterize laminar and turbulent behaviour of the Couette flow, including its transition in both directions. The Couette flow is chosen as the only flow form with constant shear stress over the flow profile, being laminar, turbulent or both. The local dissipation defines quantitative and stable criteria for the transition and the existence of turbulence. There are basic results: The Navier Stokes equations cannot describe the experimental flow profiles of the turbulent Couette flow. But they are used to quantify the dissipation of turbulent fluctuation. The dissipation minimum requires turbulent structures reaching maximum macroscopic dimensions, describing turbulence as a “non-local” phenomenon. At the transition the Couette flow profiles and the shear stress change by a factor ≅ 5 due to a change of the “apparent” turbulent viscosity by a calculated factor ≅ 27. The resulting difference of the laminar and the turbulent profiles results in two different Reynolds numbers and different loci of transition, which are identified by calculation. KW - Turbulence KW - Transition KW - Minimum dissipation Y1 - 2018 ER - TY - CHAP A1 - Finkenberger, Isabel Maria T1 - Die Stadt als städtisch-theatrale Versuchsanordnung: Wie wollen wir in Zukunft leben und welche Stadt brauchen wir dafür? T2 - Un/Certain Futures - Rollen des Designs in gesellschaftlichen Transformationsprozessen Y1 - 2024 SN - 9783839443323 U6 - https://doi.org/https://doi.org/10.1515/9783839443323-009 SP - 86 EP - 95 PB - transcript CY - Bielefeld ER - TY - JOUR A1 - Werkhausen, Amelie A1 - Albracht, Kirsten A1 - Cronin, Neil J A1 - Paulsen, Gøran A1 - Bojsen-Møller, Jens A1 - Seynnes, Olivier R T1 - Effect of training-induced changes in achilles tendon stiffness on muscle-tendon behavior during landing JF - Frontiers in physiology N2 - During rapid deceleration of the body, tendons buffer part of the elongation of the muscle-tendon unit (MTU), enabling safe energy dissipation via eccentric muscle contraction. Yet, the influence of changes in tendon stiffness within the physiological range upon these lengthening contractions is unknown. This study aimed to examine the effect of training-induced stiffening of the Achilles tendon on triceps surae muscle-tendon behavior during a landing task. Twenty-one male subjects were assigned to either a 10-week resistance-training program consisting of single-leg isometric plantarflexion (n = 11) or to a non-training control group (n = 10). Before and after the training period, plantarflexion force, peak Achilles tendon strain and stiffness were measured during isometric contractions, using a combination of dynamometry, ultrasound and kinematics data. Additionally, testing included a step-landing task, during which joint mechanics and lengths of gastrocnemius and soleus fascicles, Achilles tendon, and MTU were determined using synchronized ultrasound, kinematics and kinetics data collection. After training, plantarflexion strength and Achilles tendon stiffness increased (15 and 18%, respectively), and tendon strain during landing remained similar. Likewise, lengthening and negative work produced by the gastrocnemius MTU did not change detectably. However, in the training group, gastrocnemius fascicle length was offset (8%) to a longer length at touch down and, surprisingly, fascicle lengthening and velocity were reduced by 27 and 21%, respectively. These changes were not observed for soleus fascicles when accounting for variation in task execution between tests. These results indicate that a training-induced increase in tendon stiffness does not noticeably affect the buffering action of the tendon when the MTU is rapidly stretched. Reductions in gastrocnemius fascicle lengthening and lengthening velocity during landing occurred independently from tendon strain. Future studies are required to provide insight into the mechanisms underpinning these observations and their influence on energy dissipation. KW - achilles tendon KW - energy absorption KW - energy dissipation KW - mechanical buffer KW - stiffness Y1 - 2018 U6 - https://doi.org/10.3389/fphys.2018.00794 SN - 1664-042X IS - 9 PB - Frontiers Research Foundation CY - Lausanne ER - TY - JOUR A1 - Ketelhut, Maike A1 - Göll, Fabian A1 - Braunstein, Björn A1 - Albracht, Kirsten A1 - Abel, Dirk T1 - Comparison of different training algorithms for the leg extension training with an industrial robot JF - Current Directions in Biomedical Engineering N2 - In the past, different training scenarios have been developed and implemented on robotic research platforms, but no systematic analysis and comparison have been done so far. This paper deals with the comparison of an isokinematic (motion with constant velocity) and an isotonic (motion against constant weight) training algorithm. Both algorithms are designed for a robotic research platform consisting of a 3D force plate and a high payload industrial robot, which allows leg extension training with arbitrary six-dimensional motion trajectories. In the isokinematic as well as the isotonic training algorithm, individual paths are defined i n C artesian s pace by sufficient s upport p oses. I n t he i sotonic t raining s cenario, the trajectory is adapted to the measured force as the robot should only move along the trajectory as long as the force applied by the user exceeds a minimum threshold. In the isotonic training scenario however, the robot’s acceleration is a function of the force applied by the user. To validate these findings, a simulative experiment with a simple linear trajectory is performed. For this purpose, the same force path is applied in both training scenarios. The results illustrate that the algorithms differ in the force dependent trajectory adaption. KW - Rehabilitation Technology and Prosthetics KW - Surgical Navigation and Robotics Y1 - 2018 U6 - https://doi.org/10.1515/cdbme-2018-0005 SN - 2364-5504 VL - 4 IS - 1 SP - 17 EP - 20 PB - De Gruyter CY - Berlin ER - TY - CHAP A1 - Groß, Rolf Fritz T1 - Möglichkeiten und Grenzen für Forschung an Fachhochschulen T2 - Smart Building Convention und BIMconvention in Aachen im September Y1 - 2018 N1 - 10. und 11. September 2018, Aachen ER - TY - JOUR A1 - Rabehi, Amine A1 - Garlan, Benjamin A1 - Achtsnicht, Stefan A1 - Krause, Hans-Joachim A1 - Offenhäusser, Andreas A1 - Ngo, Kieu A1 - Neveu, Sophie A1 - Graff-Dubois, Stephanie A1 - Kokabi, Hamid T1 - Magnetic detection structure for Lab-on-Chip applications based on the frequency mixing technique JF - Sensors N2 - A magnetic frequency mixing technique with a set of miniaturized planar coils was investigated for use with a completely integrated Lab-on-Chip (LoC) pathogen sensing system. The system allows the detection and quantification of superparamagnetic beads. Additionally, in terms of magnetic nanoparticle characterization ability, the system can be used for immunoassays using the beads as markers. Analytical calculations and simulations for both excitation and pick-up coils are presented; the goal was to investigate the miniaturization of simple and cost-effective planar spiral coils. Following these calculations, a Printed Circuit Board (PCB) prototype was designed, manufactured, and tested for limit of detection, linear response, and validation of theoretical concepts. Using the magnetic frequency mixing technique, a limit of detection of 15 µg/mL of 20 nm core-sized nanoparticles was achieved without any shielding. KW - Lab-on-Chip KW - magnetic sensing KW - frequency mixing KW - superparamagnetic nanoparticles KW - magnetic beads Y1 - 2018 U6 - https://doi.org/10.3390/s18061747 SN - 1424-8220 VL - 18 IS - 6 PB - MDPI CY - Basel ER - TY - JOUR A1 - Butenweg, Christoph A1 - Marinković, Marko A1 - Kubalski, Thomas A1 - Fehling, Ekkehard A1 - Pfetzing, Thomas A1 - Meyer, Udo ED - Voss, Michael T1 - Auslegung von Stahlbetonrahmentragwerken mit Ausfachungen aus Ziegelmauerwerk (Teil 2) T1 - Design of reinforced concrete enclosures infilled with clay block masonry (Part 2) JF - Ziegelindustrie international : ZI = Brick and tile industry international N2 - Im Rahmen des europäischen Verbundprojekts INSYSME wurden von den deutschen Partnern die Systeme IMES und INODIS zur Verbesserung des seismischen Verhaltens von ausgefachten Stahlbetonrahmen entwickelt. Ziel beider Systeme ist es, Stahlbetonrahmen und Ausfachung zu entkoppeln, anstatt die Tragfähigkeit durch aufwendige und kostspielige zusätzliche Bewehrungseinlagen zu erhöhen. Erste Ergebnisse des Systems IMES für Belastungen in und senkrecht zu der Wandebene werden vorgestellt. N2 - Within the scope of the joint European project INSYSME, the German partners developed two systems - IMES and INODIS - for improving the seismic behaviour of masonry infilled reinforced concrete frames. The purpose of both systems is to decouple frame and infill instead of working to improve their load-bearing capacity by means of elaborate, expensive, supplementary reinforcing elements. Initial findings for the IMES system with regard to the loads acting in-plane and perpendicular to the wall plane (out-of-plane) are presented. Y1 - 2018 SN - 0341-0552 IS - 6 SP - 24 EP - 43 PB - Bauverlag BV GmbH CY - Gütersloh ER - TY - JOUR A1 - Butenweg, Christoph A1 - Marinković, Marko A1 - Kubalski, Thomas A1 - Fehling, Ekkehard A1 - Pfetzing, Thomas A1 - Meyer, Udo ED - Voss, Michael T1 - Auslegung von Stahlbetonrahmentragwerken mit Ausfachungen aus Ziegelmauerwerk (Teil 1) T1 - Design of reinforced concrete enclosures infilled with clay block masonry (Part 1) JF - Ziegelindustrie international : ZI = Brick and tile industry international N2 - Im Rahmen des europäischen Verbundprojekts INSYSME wurden von den deutschen Partnern die Systeme IMES und INODIS zur Verbesserung des seismischen Verhaltens von ausgefachten Stahlbetonrahmen entwickelt. Ziel beider Systeme ist es, Stahlbetonrahmen und Ausfachung zu entkoppeln, anstatt die Tragfähigkeit durch aufwendige und kostspielige zusätzliche Bewehrungseinlagen zu erhöhen. Erste Ergebnisse des Systems IMES für Belastungen in und senkrecht zu der Wandebene werden vorgestellt. N2 - Within the scope of the joint European project INSYSME, the German partners developed two systems - IMES and INODIS - for improving the seismic behaviour of masonry infilled reinforced concrete frames. The purpose of both systems is to decouple frame and infill instead of working to improve their load-bearing capacity by means of elaborate, expensive, supplementary reinforcing elements. Initial findings for the IMES system with regard to the loads acting in-plane and perpendicular to the wall plane (out-of-plane) are presented. Y1 - 2018 SN - 0341-0552 IS - 4 SP - 30 EP - 39 PB - Bauverlag BV GmbH CY - Gütersloh ER - TY - JOUR A1 - Ditzhaus, Marc A1 - Gaigall, Daniel T1 - A consistent goodness-of-fit test for huge dimensional and functional data JF - Journal of Nonparametric Statistics N2 - A nonparametric goodness-of-fit test for random variables with values in a separable Hilbert space is investigated. To verify the null hypothesis that the data come from a specific distribution, an integral type test based on a Cramér-von-Mises statistic is suggested. The convergence in distribution of the test statistic under the null hypothesis is proved and the test's consistency is concluded. Moreover, properties under local alternatives are discussed. Applications are given for data of huge but finite dimension and for functional data in infinite dimensional spaces. A general approach enables the treatment of incomplete data. In simulation studies the test competes with alternative proposals. KW - Cramér-von-Mises statistic KW - separable Hilbert space KW - huge dimensional data KW - functional data Y1 - 2018 U6 - https://doi.org/10.1080/10485252.2018.1486402 SN - 1029-0311 VL - 30 IS - 4 SP - 834 EP - 859 PB - Taylor & Francis CY - Abingdon ER - TY - JOUR A1 - Baringhaus, Ludwig A1 - Gaigall, Daniel A1 - Thiele, Jan Philipp T1 - Statistical inference for L²-distances to uniformity JF - Computational Statistics N2 - The paper deals with the asymptotic behaviour of estimators, statistical tests and confidence intervals for L²-distances to uniformity based on the empirical distribution function, the integrated empirical distribution function and the integrated empirical survival function. Approximations of power functions, confidence intervals for the L²-distances and statistical neighbourhood-of-uniformity validation tests are obtained as main applications. The finite sample behaviour of the procedures is illustrated by a simulation study. KW - Integrated empirical distribution (survival) function KW - Goodness-of-fit tests for uniformity KW - Numerical inversion of Laplace transforms KW - Coverage probability KW - Equivalence test Y1 - 2018 U6 - https://doi.org/10.1007/s00180-018-0820-0 SN - 1613-9658 VL - 2018 IS - 33 SP - 1863 EP - 1896 PB - Springer CY - Berlin ER - TY - JOUR A1 - Baringhaus, Ludwig A1 - Gaigall, Daniel T1 - Efficiency comparison of the Wilcoxon tests in paired and independent survey samples JF - Metrika N2 - The efficiency concepts of Bahadur and Pitman are used to compare the Wilcoxon tests in paired and independent survey samples. A comparison through the length of corresponding confidence intervals is also done. Simple conditions characterizing the dominance of a procedure are derived. Statistical tests for checking these conditions are suggested and discussed. KW - Wilcoxon tests KW - Pitman efficiency KW - Bahadur efficiency KW - Length of confidence intervals KW - Kernel density estimator Y1 - 2018 U6 - https://doi.org/10.1007/s00184-018-0661-4 SN - 1435-926X VL - 2018 IS - 81 SP - 891 EP - 930 PB - Springer CY - Berlin ER - TY - CHAP A1 - Czarnecki, Christian ED - vom Brocke, Jan ED - Mendling, Jan T1 - Establishment of a central process governance organization combined with operational process improvements : Insights from a BPM Project at a leading telecommunications operator in the Middle East T2 - Business process management cases : digital innovation and business transformation in practice N2 - Because of customer churn, strong competition, and operational inefficiencies, the telecommunications operator ME Telco (fictitious name due to confidentiality) launched a strategic transformation program that included a Business Process Management (BPM) project. Major problems were silo-oriented process management and missing cross-functional transparency. Process improvements were not consistently planned and aligned with corporate targets. Measurable inefficiencies were observed on an operational level, e.g., high lead times and reassignment rates of the incident management process. Y1 - 2018 SN - 978-3-319-58306-8 SN - 978-3-319-58307-5 SN - 978-3-319-86372-6 U6 - https://doi.org/10.1007/978-3-319-58307-5 N1 - Als Präsenzexemplar unter der Signatur 20 PZR 469-1 vorhanden. SP - 57 EP - 76 PB - Springer CY - Cham ER - TY - CHAP A1 - Hauk, Joachim A1 - Czarnecki, Christian A1 - Dietze, Christian ED - Rusnjak, Andreas ED - Schallmo, Daniel R. A. T1 - Prozessorientierte Messung der Customer Experience am Beispiel der Telekommunikationsindustrie T2 - Customer Experience im Zeitalter des Kunden : Best Practices, Lessons Learned und Forschungsergebnisse N2 - Hohe Wettbewerbsintensität und gestiegene Kundenanforderungen erfordern bei Telekommunikationsunternehmen eine aktive Gestaltung der Customer Experience (CX). Ein wichtiger Aspekt dabei ist die CX-Messung. Traditionelle Zufriedenheitsmessungen sind oft nicht ausreichend, um die Kundenerfahrung in komplexen Prozessen vollständig zu erfassen. Daher wird in diesem Kapitel eine prozessübergreifende Referenzlösung zur CX-Messung am Beispiel der Telekommunikationsindustrie vorgeschlagen. Ausgangspunkt ist ein industriespezifisches Prozessmodell, das sich an dem Referenzmodell eTOM orientiert. Dieses wird um Messpunkte erweitert, die Schwachstellen in Bezug auf die CX identifizieren. Für die erkannten Schwachstellen werden über eine Referenzmatrix mögliche Auslöser abgeleitet und anhand von typischen Geschäftsfallmengen bewertet. Somit ist eine direkte Zuordnung und Erfolgsmessung konkreter Maßnahmen zur Behebung der Schwachstellen möglich. Die so entwickelte Referenzlösung wurde im Projekt K1 bei der Deutschen Telekom erfolgreich umgesetzt. Details zur Umsetzung werden als Fallstudien dargestellt. Y1 - 2018 SN - 978-3-658-18961-7 SN - 978-3-658-18960-0 U6 - https://doi.org/10.1007/978-3-658-18961-7_7 SP - 195 EP - 216 PB - Springer Gabler CY - Wiesbaden ER - TY - CHAP A1 - Schneider, Dominik A1 - Wisselink, Frank A1 - Czarnecki, Christian ED - Barton, Thomas ED - Müller, Christian ED - Seel, Christian T1 - Nutzen und Rahmenbedingungen 5 informationsgetriebener Geschäftsmodelle des Internets der Dinge T2 - Digitalisierung in Unternehmen: von den theoretischen Ansätzen zur praktischen Umsetzung N2 - Im Kontext der zunehmenden Digitalisierung wird das Internet der Dinge (englisch: Internet of Things, IoT) als ein technologischer Treiber angesehen, durch den komplett neue Geschäftsmodelle im Zusammenspiel unterschiedlicher Akteure entstehen können. Identifizierte Schlüsselakteure sind unter anderem traditionelle Industrieunternehmen, Kommunen und Telekommunikationsunternehmen. Letztere sorgen mit der Bereitstellung von Konnektivität dafür, dass kleine Geräte mit winzigen Batterien nahezu überall und direkt an das Internet angebunden werden können. Es sind schon viele IoT-Anwendungsfälle auf dem Markt, die eine Vereinfachung für Endkunden darstellen, wie beispielsweise Philips Hue Tap. Neben Geschäftsmodellen basierend auf Konnektivität besteht ein großes Potenzial für informationsgetriebene Geschäftsmodelle, die bestehende Geschäftsmodelle unterstützen sowie weiterentwickeln können. Ein Beispiel dafür ist der IoT-Anwendungsfall Park and Joy der Deutschen Telekom AG, bei dem Parkplätze mithilfe von Sensoren vernetzt und Autofahrer in Echtzeit über verfügbare Parkplätze informiert werden. Informationsgetriebene Geschäftsmodelle können auf Daten aufsetzen, die in IoT-Anwendungsfällen erzeugt werden. Zum Beispiel kann ein Telekommunikationsunternehmen Mehrwert schöpfen, indem es aus Daten entscheidungsrelevantere Informationen – sogenannte Insights – ableitet, die zur Steigerung der Entscheidungsagilität genutzt werden. Außerdem können Insights monetarisiert werden. Die Monetarisierung von Insights kann nur nachhaltig stattfinden, wenn sorgfältig gehandelt wird und Rahmenbedingungen berücksichtigt werden. In diesem Kapitel wird das Konzept informationsgetriebener Geschäftsmodelle erläutert und anhand des konkreten Anwendungsfalls Park and Joy verdeutlicht. Darüber hinaus werden Nutzen, Risiken und Rahmenbedingungen diskutiert. KW - Digitale Transformation KW - Internet der Dinge KW - Monetarisierung KW - Informationsgetriebene Geschäftsmodelle KW - Qualitative Wertschöpfungsanalyse Y1 - 2018 SN - 9783658227739 SN - 9783658227722 U6 - https://doi.org/10.1007/978-3-658-22773-9_5 SP - 67 EP - 85 PB - Springer CY - Wiesbaden ER - TY - CHAP A1 - Czarnecki, Christian A1 - Auth, Gunnar ED - Barton, Thomas ED - Müller, Christian ED - Seel, Christian T1 - Prozessdigitalisierung durch Robotic 7 Process Automation T2 - Digitalisierung in Unternehmen: von den theoretischen Ansätzen zur praktischen Umsetzung N2 - Im Rahmen der digitalen Transformation werden innovative Technologiekonzepte, wie z. B. das Internet der Dinge und Cloud Computing als Treiber für weitreichende Veränderungen von Organisationen und Geschäftsmodellen angesehen. In diesem Kontext ist Robotic Process Automation (RPA) ein neuartiger Ansatz zur Prozessautomatisierung, bei dem manuelle Tätigkeiten durch sogenannte Softwareroboter erlernt und automatisiert ausgeführt werden. Dabei emulieren Softwareroboter die Eingaben auf der bestehenden Präsentationsschicht, so dass keine Änderungen an vorhandenen Anwendungssystemen notwendig sind. Die innovative Idee ist die Transformation der bestehenden Prozessausführung von manuell zu digital, was RPA von traditionellen Ansätzen des Business Process Managements (BPM) unterscheidet, bei denen z. B. prozessgetriebene Anpassungen auf Ebene der Geschäftslogik notwendig sind. Am Markt werden bereits unterschiedliche RPA-Lösungen als Softwareprodukte angeboten. Gerade bei operativen Prozessen mit sich wiederholenden Verarbeitungsschritten in unterschiedlichen Anwendungssystemen sind gute Ergebnisse durch RPA dokumentiert, wie z. B. die Automatisierung von 35 % der Backoffice-Prozesse bei Telefonica. Durch den vergleichsweise niedrigen Implementierungsaufwand verbunden mit einem hohen Automatisierungspotenzial ist in der Praxis (z. B. Banken, Telekommunikation, Energieversorgung) ein hohes Interesse an RPA vorhanden. Der Beitrag diskutiert RPA als innovativen Ansatz zur Prozessdigitalisierung und gibt konkrete Handlungsempfehlungen für die Praxis. Dazu wird zwischen modellgetriebenen und selbstlernenden Ansätzen unterschieden. Anhand von generellen Architekturen von RPA-Systemen werden Anwendungsszenarien sowie deren Automatisierungspotenziale, aber auch Einschränkungen, diskutiert. Es folgt ein strukturierter Marktüberblick ausgewählter RPA-Produkte. Anhand von drei konkreten Anwendungsbeispielen wird die Nutzung von RPA in der Praxis verdeutlicht. KW - Prozessautomatisierung KW - Geschäftsprozessmanagement KW - Softwareroboter KW - Digitale Transformation KW - Projektbeispiele Y1 - 2018 SN - 9783658227739 SN - 9783658227722 U6 - https://doi.org/10.1007/978-3-658-22773-9_7 SP - 113 EP - 131 PB - Springer CY - Wiesbaden ER - TY - JOUR A1 - Bensberg, Frank A1 - Auth, Gunnar A1 - Czarnecki, Christian T1 - Einsatz von Text Analytics zur Unterstützung literaturintensiver Forschungsprozesse: Konzeption, Realisierung und Lessons Learned JF - Anwendungen und Konzepte der Wirtschaftsinformatik N2 - Das anhaltende Wachstum wissenschaftlicher Veröffentlichungen wirft die Fragestellung auf, wie Literaturana-lysen im Rahmen von Forschungsprozessen digitalisiert und somit produktiver realisiert werden können. Insbesondere in informationstechnischen Fachgebieten ist die Forschungspraxis durch ein rasant wachsendes Publikationsaufkommen gekennzeichnet. Infolgedessen bietet sich der Einsatz von Methoden der Textanalyse (Text Analytics) an, die Textdaten automatisch vorbereiten und verarbeiten können. Erkenntnisse entstehen dabei aus Analysen von Wortarten und Subgruppen, Korrelations- sowie Zeitreihenanalysen. Dieser Beitrag stellt die Konzeption und Realisierung eines Prototypen vor, mit dem Anwender bibliographische Daten aus der etablierten Literaturdatenbank EBSCO Discovery Service mithilfe textanalytischer Methoden erschließen können. Der Prototyp basiert auf dem Analysesystem IBM Watson Explorer, das Hochschulen lizenzkostenfrei zur Verfügung steht. Potenzielle Adressaten des Prototypen sind Forschungseinrichtungen, Beratungsunternehmen sowie Entscheidungsträger in Politik und Unternehmenspraxis. KW - Text Analytics KW - Literaturanalyse KW - Forschungsprozess KW - EBSCO Discovery Service KW - IBM Watson Explorer Y1 - 2018 U6 - https://doi.org/10.26034/lu.akwi.2018.3221 SN - 2296-4592 VL - 2018 IS - 8 SP - 1 EP - 6 PB - AKWI CY - Luzern ER -