TY - GEN A1 - Gamgami, Farid A1 - Czupalla, Markus A1 - Garcia, Antonio A1 - Agnolon, David T1 - From planetary transits to spacecraft design: achieving PLATO’s pointing performance T2 - A7. Symposium on technological Requirement for future space astronomy and solar-system science missions N2 - In the last decades, several hundred exoplanets could be detected thanks to space-based observatories, namely CNES’ COROT and NASA’s Kepler. To expand this quest ESA plans to launch CHEOPS as the f irst small class mission in the cosmic visions program (S1) and PLATO as the 3rd medium class mission, so called M3 . PLATO’s primary objective is the detection of Earth like Exoplanets orbiting solar type stars in the habitable zone and characterisation of their bulk properties. This is possible by precise lightcurve measurement via 34 cameras. That said it becomes obvious that accurate pointing is key to achieve the required signal to noise ratio for positive transit detection. The paper will start with a comprehensive overview of PLATO’s mission objectives and mission architecture. Hereafter, special focus will be devoted to PLATO’s pointing requirements. Understanding the very nature of PLATO’s pointing requirements is essential to derive a design baseline to achieve the required performance. The PLATO frequency domain is of particular interest, ranging from 40 mHz to 3 Hz. Due to the very different time-scales involved, the spectral pointing requirement is decomposed into a high frequency part dominated by the attitude control system and the low frequency part dominated by the thermo-elastic properties of the spacecraft’s configuration. Both pose stringent constraints on the overall design as well as technology properties to comply with the derived requirements and thus assure a successful mission. Y1 - 2016 N1 - 67th International Astronautical Congress, 26. - 30. September 2016, Guadalajara, Mexico ER - TY - GEN A1 - Hering, T. A1 - Ulber, Roland A1 - Tippkötter, Nils T1 - Antimikrobielle Oberflächenmodifikation durch Mikropartikel T2 - Chemie Ingenieur Technik N2 - Die Ausbildung von Biofilmen in technischen Anlagen, wie z. B. Kühlkreisläufen, Wasseraufbereitungssystemen und Bioreaktoren, führen zu Materialschäden (Biofouling) und stark erhöhtem Energieaufwand. Im Rahmen der aktuellen Forschungsarbeiten erfolgen aktive sowie passive Bio-Modifikationen auf funktionalisierten magnetischen Mikropartikelober-flächen. Um die verschiedenen funktionalisierten magnetischen Mikropartikel zu analysieren und ihre antimikrobielle Wirkung zu testen, wird der Einsatz einer 3D-gedruckten, magnetischen Plattform für ein Fluoreszenz-basiertes Screening-System untersucht. Für den Oberflächenschutz wurden verschiedene, antimikrobiell funktionalisierte Partikelkombinationen mit dem Mikroorganismus Escherichia coli GFPmut2 in Bezug auf aktiven Oberflächenschutz verglichen. Um die antimikrobielle Oberflächeneffekte von synergistischen Kombinationen unterschiedlich funktionalisierter Partikel zu bestimmen, werden Oberflächen einem Magnetfeld ausgesetzt, das die Mikropartikel als definierte Schicht auf ihnen zurück hält. Diese modifizierten Oberflächen können sowohl durch Fluoreszenzspektroskopie als auch -mikroskopie analysiert werden. Y1 - 2016 U6 - https://doi.org/10.1002/cite.201650084 N1 - ProcessNet-Jahrestagung 2016 und 32. DECHEMA-Jahrestagung der Biotechnologen 2016, 12. - 15. September 2016, Eurogress Aachen VL - 88 IS - 9 SP - 1302 PB - Wiley-VCH CY - Weinheim ER - TY - GEN A1 - Kuthan, K. A1 - Al-Kaidy, H. A1 - Tippkötter, Nils T1 - Tropfenbasierte Enzymreaktionen auf Glasoberflächen im μL-Maßstab mit ortsaufgelöster pL-Dosierung der Reaktanden T2 - Chemie Ingenieur Technik N2 - Mit der Entwicklung wässriger Tropfen, die mit einer schützenden Hülle magnetisierbarer, hydrophober Partikel umgeben sind, ergeben sich neue Möglichkeiten im Bereich der Mikrofluidik. So können die Tropfen als flüssige Mikroreaktoren eingesetzt werden. Der wässrige Kern dieser Mikroreaktoren besteht aus einer Substratlösung für enzymatische Umsetzungen. Durch Bewegen der Mikroreaktoren können diese über immobilisierten Enzymen positioniert werden, um so einen enzymatischen Umsatz innerhalb der Mikroreaktoren zu realisieren. Hierfür wurde eine neue Mikroreaktorplattform-Technologie etabliert. Die Mikroreaktoren können aufgrund ihrer magnetisierbaren Hüllenpartikel über elektromagnetische Spulen bewegt werden. Die Bewegung erfolgt dabei mit einer automatisierten Aktuatorplattform, bestehend aus einer 3x3 Doppelspulenmatrix mit Magnetkernen. Als modellhaftes Reaktionssystem wird eine Enzymkaskade eingesetzt, die sich aus einer b-Glucosidase, Glucose-Oxidase und Meerrettichperoxidase zusammensetzt. Primär untersuchte Substrate sind Fluorescein-di-b-D-glucopyranoside, und 1-(3,7-Dihydroxy-10H-phenoxazin-10-yl)-ethanon, bei deren Umsatz fluoreszierende Produkte entstehen. Y1 - 2016 U6 - https://doi.org/10.1002/cite.201650117 N1 - ProcessNet-Jahrestagung 2016 und 32. DECHEMA-Jahrestagung der Biotechnologen 2016, 12. - 15. September 2016, Eurogress Aachen VL - 88 IS - 9 SP - 1336 EP - 1337 PB - Wiley-VCH CY - Weinheim ER - TY - GEN A1 - Roth, J. A1 - Tippkötter, Nils T1 - New Approach for Enzymatic Hydrolysis of Lignocellulose with Selective Diffusion Separation of the Monosaccharide Products T2 - Chemie Ingenieur Technik N2 - Enzymatic hydrolysis of lignocellulosic material plays an important role in the classical biorefinery approach. Apart from the pretreatment of the raw material, hydrolysis is the basis for the conversion of the cellulose and hemicellulose fraction into fermentable sugars. After hydrolysis, usually a solid-liquid separation takes place, in order to separate the residual plant material from the sugar-rich fraction, which can be subsequently used in a fermentation step. In order to factor out the separation step, the usage of in alginate immobilized crude cellulose fiber beads (CFBs) were evaluated. Pretreated cellulose fibers are incorporated in an alginate matrix together with the relevant enzymes. In doing so, sugars diffuse trough the alginate matrix, allowing a simplified delivery into the surrounding fluid. This again reduces product inhibition of the glucose on the enzyme catalysts. By means of standardized bead production the hydrolysis in lab scale was possible. First results show that liberation of glucose and xylose is possible, allowing a maximum total sugar yield of 75 %. Y1 - 2016 U6 - https://doi.org/10.1002/cite.201650301 SN - 0009-286X SN - 1522-2640 (eISSN) N1 - ProcessNet-Jahrestagung 2016 und 32. DECHEMA-Jahrestagung der Biotechnologen 2016, 12. - 15. September 2016, Eurogress Aachen VL - 88 IS - 9 SP - 1237 PB - Wiley-VCH CY - Weinheim ER - TY - GEN A1 - Wulfhorst, H. A1 - Merseburg, J. A1 - Tippkötter, Nils T1 - Batteriekomponenten aus nachwachsenden Rohstoffen T2 - Chemie Ingenieur Technik N2 - In diesem Beitrag geht es um die Integration von Stoffströmen einer Lignocellulose-Bioraffinerie in Verfahren zur Batterieherstellung. Pflanzliche Reststoffe aus der Biokraftstoffherstellung wie Lignin sollen zur Herstellung neuer Batteriematerialien verwendet werden. Hierbei wird das Lignin als Matrix für die vorgraphitischen C-haltigen Einlagerungsverbindungen in den Elektroden genutzt. Die Si-C-Komposite werden durch das Einbetten von Si in eine Ligninmatrix mit anschließender Carbonisierung hergestellt. Das Lignin hierfür wird durch die sequentielle hydrothermale Vorbehandlung von Buchenholz bei variablen Bedingungen gewonnen und mit Si-Nanopartikel sowie als Referenz ohne Si-Nanopartikel gefällt. Die Ergebnisse zeigen, dass die sequenzielle Vorbehandlung höhere Ausbeuten im Vergleich zum LHW- oder Organosolv-Aufschluss liefert. Um eine Anode herzustellen, wurde das resultierende Si–C-Kompositmaterial carbonisiert, auf einen Stromsammler aufgetragen und elektro-chemisch charakterisiert. Der Einfluss der Vorbehandlungsschritte auf den Herstellungsprozess und die ökonomische Bewertung des untersuchten Bioraffinerie-Prozesses wurde mithilfe eines Stoffstrommodells analysiert. Y1 - 2016 U6 - https://doi.org/10.1002/cite.201650333 SN - 0009-286X SN - 1522-2640 (eISSN) N1 - ProcessNet-Jahrestagung 2016 und 32. DECHEMA-Jahrestagung der Biotechnologen 2016, 12. - 15. September 2016, Eurogress Aachen VL - 88 IS - 9 SP - 1234 EP - 1235 PB - Wiley-VCH CY - Weinheim ER - TY - GEN A1 - Engel, M. A1 - Tippkötter, Nils T1 - Einfluss eines Phenazin-Mediators und elektrischen Potenzials auf die Aceton-Butanol-Ethanol-Fermentation T2 - Chemie Ingenieur Technik N2 - In den letzten Jahren haben nachhaltige, biotechnologische Prozesse zunehmend an Bedeutung gewonnen. Die Aceton-Butanol-Ethanol-Fermentation (ABE-Fermentation) mit dem anaeroben Bakterium Clostridium acetobutylicum zur Gewinnung von Biobutanol könnte in diesem Zusammenhang eine Möglichkeit der nachhaltigen Kraftstoffproduktion darstellen. In dieser Arbeit wird der Einfluss zusätzlich verfügbarer Elektronen durch den Einsatz des Phenazin-Farbstoffs Neutralrot als Redoxmediator sowie das Anlegen eines elektrischen Potenzials während der ABE-Fermentation untersucht. Es wird gezeigt, dass das Neutralrot keinen Einfluss auf die Leerlaufspannung von ca. 500 mV vs. Ag/AgCl während der Fermentation hat. Der Mediator bewirkt allerdings eine frühere Butanolbildung sowie höhere Butanolkonzentrationen. Wird zudem die Mediatorkonzentration von 125 mM auf 250 mM angehoben, wird dabei auch die maximale Butanolkonzentration um 36 % ± 1,8 % innerhalb von28 Stunden gesteigert. Y1 - 2016 U6 - https://doi.org/10.1002/cite.201650105 SN - 0009-286X SN - 1522-2640 (eISSN) N1 - ProcessNet-Jahrestagung 2016 und 32. DECHEMA-Jahrestagung der Biotechnologen 2016, 12. - 15. September 2016, Eurogress Aachen VL - 88 IS - 9 SP - 1254 PB - Wiley-VCH CY - Weinheim ER - TY - GEN A1 - Capitain, C. A1 - Hering, T. A1 - Tippkötter, Nils T1 - Enzymatische Polymerisation von Ligninmodellkomponenten und Organosolv-Lignin mit aromatischen Aminosäuren T2 - Chemie Ingenieur Technik N2 - Die stoffliche Nutzung von Lignin aus Bioraffinerien ist ein wichtiger Bestandteil für den Wertschöpfungsprozess von nachwachsenden, pflanzlichen Rohstoffen. Lignin zählt zu den wenigen erneuerbaren Quellen für phenolische Bestandteile, wird aber derzeit meist nur thermisch verwertet. Ziel dieses Forschungsvorhabens ist die Funktionalisierung von Lignin zur Verbesserung der Adhäsionseigenschaften. Als funktionelle Gruppe wird die aromatische Aminosäure L-DOPA verwendet, die charakteristisch für die Adhäsionskraft von Muscheln ist. Lignin ist ein geeignetes Stützgerüst, da es ein Polymer ist, das durch enzymkatalysierte Polymerisation gebildet wird. Essenziell für die Entwicklung ist ein besseres Verständnis über die Bildung von Lignin-Polymeren und deren verschiedene Eigenschaften. Um die Einflussfaktoren auf Kettenlänge und Polymerisationseffizienz zu untersuchen, werden zurzeit sowohl Ligninmodellkomponenten (LMK) als auch gelöstes Organosolv-Lignin verwendet. Laufende Untersuchungen werden zeigen, ob sich die enzymatische Polymerisationsreaktion auf ein gelöstes Ligninpolymer aus einem Organosolv-Aufschluss übertragen lässt. Y1 - 2016 U6 - https://doi.org/10.1002/cite.201650374 SN - 0009-286X SN - 1522-2640 (eISSN) N1 - ProcessNet-Jahrestagung 2016 und 32. DECHEMA-Jahrestagung der Biotechnologen 2016, 12. - 15. September 2016, Eurogress Aachen VL - 88 IS - 9 SP - 1236 PB - Wiley-VCH CY - Weinheim ER - TY - GEN A1 - Möhring, S. A1 - Wulfhorst, H. A1 - Capitain, C. A1 - Roth, J. A1 - Tippkötter, Nils T1 - Fractioning of lignocellulosic biomass: Scale-down and automation of thermal pretreatment for parameter optimization T2 - Chemie Ingenieur Technik N2 - In order to efficiently convert lignocellulose, it is often necessary to conduct a pretreatment. The biomass considered in this study typically comprises of agricultural and horticultural residues, as well as beechwood. A very environmentally friendly method, namely, fungal pretreatment using white-rot fungi, leads to an enhanced enzymatic hydrolysis. In contrast to other processes presented, the energy input is extremely low. However, the fungal growth on the lignocellulosic substrates takes several weeks at least in order to be effective. Thus, the reduction of chemicals and energy for thermal processing is a target of our current research. Liquid hot water (LHW) and solvent-based pretreatment (OrganoSolv) require more complex equipment, as they depend on high temperatures (160 – 180 °C) and enhanced pressure (up to 20 bar). However, they prove to be promising processes in regard to the fractioning of lignocellulose. For optimal lignin recovery the parameters differ from those established in cellulose extraction. A novel screening system scaled down to a reaction volume of 100 mL has been developed and successfully tested for this purpose. Y1 - 2016 U6 - https://doi.org/10.1002/cite.201650288 SN - 0009-286X SN - 1522-2640 (eISSN) N1 - ProcessNet-Jahrestagung und 32. DECHEMA-Jahrestagung der Biotechnologen 2016, 12. - 15. September 2016, Eurogress Aachen VL - 88 IS - 9 SP - 1229 PB - Wiley-VCH CY - Weinheim ER - TY - CHAP A1 - Engel, Mareike A1 - Thieringer, Julia A1 - Tippkötter, Nils T1 - Linking bioprocess engineering and electrochemistry for sustainable biofuel production T2 - Young Researchers Symposium, YRS 2016. Proceedings N2 - Electromicrobial engineering is an emerging, highly interdisciplinary research area linking bioprocesses with electrochemistry. In this work, microbial electrosynthesis (MES) of biobutanol is carried out during acetone-butanol-ethanol (ABE) fermentations with Clostridium acetobutylicum. A constant electric potential of −600mV (vs. Ag/AgCl) with simultaneous addition of the soluble redox mediator neutral red is used in order to study the electron transfer between the working electrode and the bacterial cells. The results show an earlier initiation of solvent production for all fermentations with applied potential compared to the conventional ABE fermentation. The f inal butanol concentration can be more than doubled by the application of a negative potential combined with addition of neutral red. Moreover a higher biofilm formation on the working electrode compared to control cultivations has been observed. In contrast to previous studies, our results also indicate that direct electron transfer (DET) might be possible with C. acetobutylicum. The presented results make microbial butanol production economically attractive and therefore support the development of sustainable production processes in the chemical industry aspired by the “Centre for resource-efficient chemistry and raw material change” as well as the the project “NanoKat” working on nanostructured catalysts in Kaiserslautern. Y1 - 2016 N1 - Young Researchers Symposium, YRS 2016, 14th - 15th April 2016, Fraunhofer-Zentrum Kaiserslautern SP - 49 EP - 53 PB - Fraunhofer Verlag CY - Karlsruhe ER - TY - CHAP A1 - Lu, S. A1 - Beyer, K. A1 - Bosiljkov, V. A1 - Butenweg, Christoph A1 - D’Ayala, D. A1 - Degee, H. A1 - Gams, M. A1 - Klouda, J. A1 - Lagomarsino, S. A1 - Penna, A. A1 - Mojsilovic, N. A1 - da Porto, F. A1 - Sorrentino, L. A1 - Vintzileou, E. ED - Modena, Claudio ED - da Porto, F. ED - Valluzzi, M.R. T1 - Next generation of Eurocode 8, masonry chapter T2 - Brick and Block Masonry Proceedings of the 16th International Brick and Block Masonry Conference, Padova, Italy, 26-30 June 2016 N2 - This paper describes the procedure on the evaluation of the masonry chapter for the next generation of Eurocode 8, the European Standard for earthquake-resistant design. In CEN, TC 250/SC8, working group WG 1 has been established to support the subcommittee on the topic of masonry on both design of new structures (EN1998-1) and assessment of existing structures (EN1998-3). The aim is to elaborate suggestions for amendments which fit the current state of the art in masonry and earthquake-resistant design. Focus will be on modelling, simplified methods, linear-analysis (q-values, overstrength-values), nonlinear procedures, out-of-plane design as well as on clearer definition of limit states. Beside these, topics related to general material properties, reinforced masonry, confined masonry, mixed structures and non-structural infills will be covered too. This paper presents the preliminary work and results up to the submission date. Y1 - 2016 SN - 978-1-138-02999-6 (Print) SN - 9781315374963 (E-Book) SP - 695 EP - 700 PB - Taylor & Francis CY - London ER - TY - RPRT A1 - Höfler, Matthias A1 - Groß, Rolf Fritz T1 - Optimierung der Oxidationskinetik von Sulfit zu Sulfat durch effiziente feinblasige Belüftung bei Anlagen zur Rauchgasentschwefelung fossil befeuerter Kraftwerke und Industrieanlagen mittels Seewasser ("Optiox") N2 - Das Forschungsvorhaben Optiox beschäftigt sich mit der Optimierung eines Belüftungsbeckens zur Rauchgasentschwefelung fossil befeuerter Kraftwerke mittels Seewasser. Unter Neutralisierung der entstehenden Hydroniumionen (H3O+) durch die natürliche Alkalität des Seewassers dissoziiert Schwefeldioxid aus dem Rauchgase im vorgeschalteten Absorber beim Phasenübergang von der Gas- in die Flüssigphase zu Sulfiten. Im Belüftungsbecken werden diese Sulfite mittels eingeblasener Luft zu Sulfaten oxidiert, was zu einer geringen Erhöhung der Sulfatfracht vor Einleitung ins Meer führt, die unterhalb der natürlichen Schwankungen liegt. Daneben dient das Belüftungsbecken der Konditionierung des Seewassers hinsichtlich pH-Wert und Sauerstoffgehalt und ist mit hoch effizienten Belüftern ausgestattet, deren Spezifikation den jeweiligen Randbedingungen, wie Abscheideleistung des Absorbers, Beckengeometrie sowie lokalen Gegebenheiten angepasst wird. Y1 - 2016 N1 - Projektlaufzeit: 10/2012 – 09/2015 Gefördert durch: BMBF – Förderkennlinie Ingenieurnachwuchs Kooperationspartner: Doosan Lentjes GmbH, Ratingen, FH Aachen, Fachbereich Energietechnik, Prof. Dr.-Ing. Rolf Groß ER - TY - THES A1 - Gaigall, Daniel T1 - Vergleich von statistischen Tests im verbundenen und unabhängigen Stichprobenfall N2 - Es werden Effizienzbegriffe zum Vergleich von statistischen Tests basierend auf verschiedenen statistischen Experimenten eingeführt. Dabei handelt es sich um die schon aus dem Vergleich von statistischen Tests in je demselben Modell bekannten asymptotischen relativen Effizienzen wie die Hodges-Lehmann-Effizienz, die Bahadur-Effizienz und die Pitman-Effizienz sowie um Kriterien basierend auf Volumina von Konfidenzbereichen. Effizienzaussagen werden unter anderem für Likelihood-Quotienten-Tests und Waldsche Tests im Rahmen eines allgemeinen multivariaten parametrischen Modells erhalten. Statistische Tests zur Prüfung von Hypothesen über die relative Wirksamkeit zweier Experimente werden vorgeschlagen. Auf der Grundlage der erhaltenen Ergebnisse erfolgt ein Vergleich der Wirksamkeit von korrespondierenden Verfahren bei verbundener Stichprobenerhebung und unabhängiger Stichprobenerhebung. Die Rolle der Kovarianzmatrix bei verbundener Stichprobenerhebung wird insbesondere unter der Annahme, dass die zugrunde liegenden Verteilungen durch k-parametrische Exponentialfamilien modellierbar sind, herausgearbeitet. Verbindungen zu Effizienzbegriffen bei Punkt- und Konfidenzbereichsschätzverfahren werden aufgezeigt. Ausführlichere Untersuchungen betreffen die korrespondierenden Hotellingschen T²-Tests im multivariaten Normalverteilungsfall, die klassischen Homogenitatstests bei k × k-Kontingenztafeln und die Wilcoxon Tests in nichtparametrischen Lagealternativmodellen KW - Vergleich von Experimenten KW - Hypothesentests KW - Effizienz KW - testing hypotheses KW - efficiency Y1 - 2016 U6 - https://doi.org/10.15488/8678 N1 - Dissertation, Gottfried Wilhelm Leibniz Universität Hannover, 2016 PB - Gottfried Wilhelm Leibniz Universität Hannover CY - Hannover ER - TY - JOUR A1 - Hörenbaum, Christoph A1 - Laumann, Jörg A1 - Prokop, Ines T1 - Zur Anwendung des Eurocode 3 Teil 1-2 für die Heißbemessung und Anregungen für dessen Novellierung JF - Stahlbau N2 - Die Eurocodes werden bis zum Jahr 2020 im Europäischen Komitee für Normung (CEN), Technisches Komitee TC 250, überarbeitet. In Vorbereitung auf die Eurocode-Novellierung haben engagierte Ingenieure im Rahmen der Initiative PraxisRegeln Bau (PRB) die für die praktische Anwendung häufig genutzten Teile des Eurocode 3 untersucht. Mit dem Ziel, die Praxistauglichkeit des Eurocode 3 für die Heißbemessung zu verbessern, wurden die bestehende Norm EN 1993 Teil 1-2 insbesondere in Bezug auf die Anwenderfreundlichkeit analysiert und Vorschläge für die europäische Novellierung erarbeitet. Die Analysen zeigen, dass durch Umstrukturierungen und durch die Einführung von Tabellen die Verständlichkeit und Anwenderfreundlichkeit der Regeln für die Heißbemessung bedeutend erhöht werden können. KW - EN 1993-1-2 KW - Tragwerksbemessung KW - Brandfall KW - Forschung, pränormativ KW - structural design Y1 - 2016 U6 - https://doi.org/10.1002/stab.201610382 SN - 1437-1049 VL - 85 IS - 6 SP - 429 EP - 434 PB - Ernst & Sohn GmbH CY - Berlin ER - TY - CHAP A1 - Nursinski-Stolberg, André A1 - Gangatharan, Kiritharan A1 - Czarnecki, Christian ED - Mayr, Heinrich C. ED - Pinzger, Martin T1 - Development of a subject-oriented reference process model for the telecommunications industry T2 - GI Edition Proceedings Band 259 INFORMATIK 2016 N2 - Generally the usage of reference models can be structured top-down or bottom-up. The practical need of agile change and flexible organizational implementation requires a consistent mapping to an operational level. In this context, well-established reference process models are typically structured top-down. The subject-oriented Business Process Management (sBPM) offers a modeling concept that is structured bottom-up and concentrates on the process actors on an operational level. This paper applies sBPM to the enhanced Telecom Operations Map (eTOM), a well-accepted reference process model in the telecommunications industry. The resulting design artifact is a concrete example for a combination of a bottom-up and top-down developed reference model. The results are evaluated and confirmed in practical context through the involvement of the industry body TMForum. KW - Subject-oriented Business Process Management KW - Reference Process Model KW - eTOM KW - Telecommunications Industry. Y1 - 2016 SN - 9783885796534 SN - 1617-5468 N1 - 26.-30. September 2016, Klagenfurt. SP - 699 EP - 712 PB - Gesellschaft für Informatik e.V. CY - Bonn ER - TY - CHAP A1 - Czarnecki, Christian ED - Mayr, Heinrich C. ED - Pinzger, Martin ED - Gesellschaft für Informatik e. V. (GI), T1 - Design und Nutzung einer industriespezifischen Referenzarchitektur für die Telekommunikationsindustrie T2 - GI Edition Proceedings Band 259 INFORMATIK 2016. 26.-30. September 2016 Klagenfurt N2 - Zur Unterstützung des Transformationsbedarfs von Telekommunikationsunternehmen sind die Referenzmodelle des TM Forums in der Praxis weltweit anerkannt. Dabei findet jedoch meist eine losgelöste Nutzung für spezifische Einzelthemen statt. Daher führt dieser Artikel die bestehenden Inhalte in einer industriespezifischen, übergreifenden Referenzarchitektur zusammen. Der Fokus liegt auf den Ebenen Aufbauorganisation, Prozesse, Applikationen und Daten. Darüber hinaus werden inhaltliche Architekturdomänen zur Strukturierung angeboten. Die Referenzarchitektur ist hierarchisch aufgebaut und wird hier beispielhaft für ausgewählte, aggregierte Inhalte beschrieben. Als erste Evaluation wird die Anwendung der Referenzarchitektur in drei Praxisprojekten erläutert. KW - Referenzmodellierung KW - Unternehmensarchitektur KW - Unternehmenstransformation KW - TM Forum KW - enhanced Telecom Operations Map (eTOM) Y1 - 2016 SN - 9783885796534 SN - 1617-5468 SP - 807 EP - 814 PB - Köllen CY - Bonn ER - TY - CHAP A1 - Steuer-Dankert, Linda A1 - Leicht-Scholten, Carmen T1 - Social responsibility and innovation - Key competencies for engineers T2 - ICERI 2016: 9th International Conference of Education, Research and Innovation: Conference Proceedings : Seville (Spain), 14-16 November N2 - Engineers are of particular importance for the societies of tomorrow. The big social challenges society has to cope with in future, can only be mastered, if engineers link the development and innovation process closely with the requirements of people. As a result, in the frame of the innovation process engineers have to design and develop products for diverse users. Therefore, the consideration of diversity in this process is a core competence engineers should have. Implementing the consideration of diverse requirements into product design is also linked to the development of sustainable products and thus leads to social responsible research and development, the core concept formulated by the EU. For this reason, future engineers should be educated to look at the technical perspectives of a problem embedded in the related questions within societies they are developing their artefacts for. As a result, the aim of teaching engineering should be to prepare engineers for these requirements and to draw attention to the diverse needs in a globalized world. To match the competence profiles of future engineers to the global challenges and the resulting social responsibility, RWTH Aachen University, one of the leading technical universities in Germany, has established the bridging professorship “Gender and Diversity in Engineering” (GDI) which educates engineers with an interdisciplinary approach to expand engineering limits. The interdisciplinary teaching concept of the research group pursues an approach which imparts an application oriented Gender and Diversity expertise to future engineers. In the frame of an established teaching concept, which is a result of experiences and expertise of the research group, students gain theoretical knowledge about Gender and Diversity and learn how to transfer their knowledge into their later field of action. In the frame of the conference the institutional approach will be presented as well as the teaching concept which will be introduced by concrete course examples. KW - diversity KW - innovation KW - social responsible engineering KW - engineering education Y1 - 2016 SN - 978-84-617-5895-1 U6 - https://doi.org/10.21125/iceri.2016.0353 SN - 2340-1095 SP - 5967 EP - 5976 ER - TY - CHAP A1 - Leicht-Scholten, Carmen A1 - Steuer-Dankert, Linda A1 - Bouffier, Anna T1 - Facing Future Challenges: Building Engineers for Tomorrow T2 - Conference proceedings : new perspectives in science education : 5th Conference edition, Florence, Italy, 17-18 March 2016 N2 - Future engineers are increasingly confronted with the so-called Megatrends which are the big social challenges society has to cope with. These Megatrends, such as “Silver Society”, “Globalization”, “Mobility” and “Female Shift” require an application-oriented perspective on Diversity especially in the engineering field. Therefore, it is necessary to enable future engineers not only to look at the technical perspectives of a problem, but also to be able to see the related questions within societies they are developing their artefacts for. The aim of teaching engineering should be to prepare engineers for these requirements and to draw attention to the diverse needs in a globalized world. Bringing together technical knowledge and social competences which go beyond a mere training of the so-called “soft skills”, is a new approach followed at RWTH Aachen University, one of the leading technical universities in Germany. RWTH Aachen University has established the bridging professorship “Gender and Diversity in Engineering” (GDI) which educates engineers with an interdisciplinary approach to expand engineering limits. In the frame of a sustainable teaching concept the research group under the leadership of Prof. Carmen Leicht-Scholten has developed an approach which imparts a supplication-specific Gender and Diversity expertise to engineers. In workshops students gain theoretical knowledge about Gender and Diversity and learn how to transfer their knowledge in their special field of study and later work. To substantiate this, the course participants have to solve case studies from real life. The cases which are developed in collaboration with non-profit organizations and enterprises from economy rise the students to challenges which are inspired by professional life. Evaluation shows the success of this approach as well as an increasing demand for such teaching formats. KW - Diversity KW - Engineering Education KW - Gender KW - Higher Education Y1 - 2016 SN - 978-886292-705-5 SP - 32 EP - 37 ER - TY - CHAP A1 - Grundmann, Jan Thimo A1 - Biele, Jens A1 - Dachwald, Bernd A1 - Grimm, Christian A1 - Lange, Caroline A1 - Ulamec, Stephan T1 - Small spacecraft for small solar system body science, planetary defence and applications T2 - IEEE Aerospace Conference 2016 N2 - Following the recent successful landings and occasional re-awakenings of PHILAE, the lander carried aboard ROSETTA to comet 67P/Churyumov-Gerasimenko, and the launch of the Mobile Asteroid Surface Scout, MASCOT, aboard the HAYABUSA2 space probe to asteroid (162173) Ryugu we present an overview of the characteristics and peculiarities of small spacecraft missions to small solar system bodies (SSSB). Their main purpose is planetary science which is transitioning from a ‘pure’ science of observation of the distant to one also supporting in-situ applications relevant for life on Earth. Here we focus on missions at the interface of SSSB science and planetary defence applications. We provide a brief overview of small spacecraft SSSB missions and on this background present recent missions, projects and related studies at the German Aerospace Center, DLR, that contribute to the worldwide planetary defence community. These range from Earth orbit technology demonstrators to active science missions in interplanetary space. We provide a summary of experience from recently flown missions with DLR participation as well as a number of studies. These include PHILAE, the lander of ESA’s ROSETTA comet rendezvous mission now on the surface of comet 67P/Churyumov-Gerasimenko, and the Mobile Asteroid Surface Scout, MASCOT, now in cruise to the ~1 km diameter C-type near-Earth asteroid (162173) Ryugu aboard the Japanese sample-return probe HAYABUSA2. We introduce the differences between the conventional methods employed in the design, integration and testing of large spacecraft and the new approaches developed by small spacecraft projects. We expect that the practical experience that can be gained from projects on extremely compressed timelines or with high-intensity operation phases on a newly explored small solar system body can contribute significantly to the study, preparation and realization of future planetary defence related missions. One is AIDA (Asteroid Impact & Deflection Assessment), a joint effort of ESA, JHU/APL, NASA, OCA and DLR, combining JHU/APL’s DART (Double Asteroid Redirection Test) and ESA’s AIM (Asteroid Impact Monitor) spacecraft in a mission towards near-Earth binary asteroid system (65803) Didymos. DLR is currently applying MASCOT heritage and lessons learned to the design of MASCOT2, a lander for the AIM mission to support a bistatic low frequency radar experiment with PHILAE/ROSETTA CONSERT heritage to explore the inner structure of Didymoon which is the designated impact target for DART. Y1 - 2016 SP - 1 EP - 20 ER - TY - CHAP A1 - Hallmann, Marcus A1 - Heidecker, Ansgar A1 - Schlotterer, Markus A1 - Dachwald, Bernd T1 - GTOC8: results and methods of team 15 DLR T2 - 26th AAS/AIAA Space Flight Mechanics Meeting, Napa, CA N2 - This paper describes the results and methods used during the 8th Global Trajectory Optimization Competition (GTOC) of the DLR team. Trajectory optimization is crucial for most of the space missions and usually can be formulated as a global optimization problem. A lot of research has been done to different type of mission problems. The most demanding ones are low thrust transfers with e.g. gravity assist sequences. In that case the optimal control problem is combined with an integer problem. In most of the GTOCs we apply a filtering of the problem based on domain knowledge. Y1 - 2016 N1 - 26th AAS/AIAA Space Flight Mechanics Meeting, February 14-18, 2016, Napa, California, U.S.A. Napa, CA ER - TY - CHAP A1 - König, Johannes Alexander A1 - Wolf, Martin T1 - A new definition of competence developing games - and a framework to assess them T2 - ACHI 2016 : The Ninth International Conference on Advances in Computer-Human Interactions N2 - There are different types of games that try to make use of the motivation of a gaming situation in learning contexts. This paper introduces the new terminology ‘Competence Developing Game’ (CDG) as an umbrella term for all games with this intention. Based on this new terminology, an assessment framework has been developed and validated in scope of an empirical study. Now, all different types of CDGs can be evaluated according to a defined and uniform set of assessment criteria and, thus, are comparable according to their characteristics and effectiveness. KW - Serious Games KW - Gamification KW - Business Simulations KW - Assessment Y1 - 2016 SN - 978-1-61208-468-8 N1 - Proceeding of the Ninth International Conference on Advances in Computer-Human Interactions (ACHI 2016), Venice. SP - 95 EP - 97 ER -