TY - CHAP A1 - Stoschek, Oliver A1 - Potthoff, Michael A1 - Petersen, Ole Svenstrup A1 - Larsen, Ole A1 - Engels, Ralf T1 - Ökologische Modellierung von Gewässergüteparametern an der Tide-Elbe N2 - Dr.-Ing. Oliver Stoschek [u.a.] DHI Wasser und Umwelt GmbH, Syke. 14 S. (S. 45-58). Beitrag zum 2. Aachener Softwaretag in der Wasserwirtschaft <2, 2009, Aachen> Ökologische Modelle zur Berechnung der Temperaturveränderung und den Einfluss von Kühlwasser auf die Wassertemperatur der Elbe. Die vorgelegte Arbeit wurde beauftragt und unterstützt von der ARGE Elbe im Zuge der Neuauflage des Wärmelastplans Elbe. KW - Wassergüte KW - Wasserwirtschaft KW - Wärmelastplan Y1 - 2009 ER - TY - CHAP A1 - Lang, H. A1 - Wirtz, K. A1 - Heitzer, Michael A1 - Staat, Manfred A1 - Oettel, R. T1 - Zyklische Einspielversuche zur Verifikation von Shakedown-Analysen mittels FEM T1 - Cyclic plastic deformation test to verify FEM-based shakedown analysis N2 - Im Rahmen von Ermüdungsanalysen ist nachzuweisen, daß die thermisch bedingten fortschreitenden Deformationen begrenzt bleiben. Hierzu ist die Abgrenzung des Shakedown-Bereiches (Einspielen) vom Ratchetting-Bereich (fortschreitende Deformation) von Interesse. Im Rahmen eines EU-geförderten Forschungsvorhabens wurden Experimente mit einem 4-Stab-Modell durchgeführt. Das Experiment bestand aus einem wassergekühlten inneren Rohr und drei isolierten und beheizbaren äußeren Probestäben. Das System wurde durch alternierende Axialkräfte, denen alternierende Temperaturen an den äußeren Stäben überlagert wurden, belastet. Die Versuchsparameter wurden teilweise nach vorausgegangenen Einspielanalysen gewählt. Während der Versuchsdurchführung wurden Temperaturen und Dehnungen zeitabhängig gemessen. Begleitend und nachfolgend zur Versuchsdurchführung wurden die Belastungen und die daraus resultierenden Beanspruchungen nachvollzogen. Bei dieser inkrementellen elasto-plastischen Analyse mit dem Programm ANSYS wurden unterschiedliche Werkstoffmodelle angesetzt. Die Ergebnisse dieser Simulationsberechnung dienen dazu, die Shakedown-Analysen mittels FE-Methode zu verifizieren. KW - Einspielen KW - Traglast KW - Finite-Elemente-Methode KW - Shakedown KW - shakedown analysis KW - plastic deformation Y1 - 1999 ER - TY - CHAP A1 - Schermutzki, Margret T1 - Zur Bedeutung der Workload N2 - Informationen zur Einführung von ECTS zur europäisch einheitlichen Bewertung von Studienleistungen Basierung der ECTS auf der tatsächlichen Arbeitsbelastung der Studierenden Möglichkeiten zur Ermittlung der Arbeitsbelastung KW - Bologna-Prozess KW - ECTS KW - Arbeitsbelastung KW - Europäisches Leistungspunktesystem KW - Bewertung von Studienleistungen . Studierendenmobilität KW - European Credit Transfer System KW - Workload Y1 - 2005 ER - TY - CHAP A1 - Koplin, Tobias J. A1 - Siemons, Maike A1 - Océn-Valéntin, César A1 - Sanders, Daniel A1 - Simon, Ulrich T1 - Workflow for high throughput screening of gas sensing materials N2 - The workflow of a high throughput screening setup for the rapid identification of new and improved sensor materials is presented. The polyol method was applied to prepare nanoparticular metal oxides as base materials, which were functionalised by surface doping. Using multi-electrode substrates and high throughput impedance spectroscopy (HT-IS) a wide range of materials could be screened in a short time. Applying HT-IS in search of new selective gas sensing materials a NO2-tolerant NO sensing material with reduced sensitivities towards other test gases was identified based on iridium doped zinc oxide. Analogous behaviour was observed for iridium doped indium oxide. KW - Biosensor KW - High throughput experimentation KW - gas sensor KW - metal oxide KW - doping KW - impedance spectroscopy KW - nitrogen oxides Y1 - 2006 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:hbz:a96-opus-1407 ER - TY - CHAP A1 - Hüning, Felix A1 - Heuermann, Holger A1 - Wache, Franz-Josef T1 - Wireless CAN T2 - Tagungsband AALE 2018 : das Forum für Fachleute der Automatisierungstechnik aus Hochschulen und Wirtschaft ; 15. Fachkonferenz, Regensburg ; [15. Konferenz für Angewandte Automatisierungstechnik in Lehre und Entwicklung / TH Köln; VFAALE, Verein der Freunde und Förderer der Angewandten Automatisierungstechnik] N2 - Das vorgestellte System zu Wireless CAN bietet die Möglichkeit, CAN kabellos zu übertragen. Beide vorgestellten und entwickelten Konzepte funktionieren korrekt und ermöglichen den Auf-bau von kabellosen CAN Schnittstellen. Durch den kleinen Aufbau kann diese Technologie auch für eingebettete Systeme verwendet werden. Zudem bietet dieser Ansatz die Möglichkeit, durch die Entwicklung von geeigneten ICs die Größe des Systems bis auf Bauteilgröße zu reduzieren, um eine noch bessere Integration in eingebettete Systeme zu ermöglichen. Dadurch wird die Technologie attraktiv für Einsatzgebiete, wo die oben aufgelisteten Vorteile zum Tragen kommen können. Diese Einsatzgebiete können sowohl im Automobil als auch im Industriebereich liegen. Y1 - 2018 SP - 135 EP - 144 PB - VDE Verlag ER - TY - CHAP A1 - Arinkin, Vladimir A1 - Digel, Ilya T1 - Water bridge phenomenon : [abstract] N2 - One of interesting but not well known water properties is related to appearance of highly ordered structures in response to strong electrical field. In 1893 Sir William Armstrong placed a cotton thread between two wine glasses filled with chemically pure water. When high DC voltage was applied between the glasses, a connection consisting of water formed, producing a "water bridge" KW - Hydrodynamik KW - Elektrodynamik KW - Wasserbrücke KW - water bridge phenomenon Y1 - 2009 ER - TY - CHAP A1 - Kraft, Bodo A1 - Zöll, Axel ED - Engstler, Martin T1 - Von der Langstrecke zum Sprint – Agile Methoden in traditionellen Unternehmen T2 - Projektmanagement und Vorgehensmodelle 2014 : soziale Aspekte und Standardisierung Y1 - 2014 SN - 978-3-88579-630-5 N1 - Gemeinsame Tagung der Fachgruppen Projektmanagement (WI-PM) und Vorgehensmodelle (WI-VM) im Fachgebiet Wirtschaftsinformatik der Gesellschaft für Informatik e.V. ; 16. und 17. Oktober 2014 in Stuttgart ; PVM <1, 2014, Stuttgart> GI-Edition : Proceedings ; 236 SP - 35 EP - 46 PB - Gesellschaft für Informatik CY - Bonn ER - TY - CHAP A1 - Merten, Sabine A1 - Kämper, Klaus-Peter A1 - Brill, Manfred A1 - Picard, Antoni A1 - Cassel, Detlev A1 - Jentsch, Andreas A1 - Rollwa, Markus T1 - Vom virtuellen Wafer zum realen Drucksensor N2 - Das Technologiepraktikum „Virtuelle Sensor-Fertigung“ ist ein Beispiel für die medientechnische Aufbereitung von Lern- und Lehrmaterial unter didaktischen Gesichtspunkten. Studierende lernen einen Fertigungsprozess mit Hilfe von virtuellen Maschinen kennen, bevor sie die reale Prozesskette im Laborpraktikum im Reinraum durchführen. N2 - The technology course “Fabrication of a microsensor” represents a multimediabased approach towards education in high technology production in consideration of didactical aspects. The students learn the operation of a complex microfabrication line with the help of virtual fabrication machines before they perform the actual process in a hands-on training in an actual clean room. KW - Virtuelle Maschine KW - VM KW - Virtuelle Sensor-Fertigung KW - virtual fabrication of a microsensor Y1 - 2003 ER - TY - CHAP A1 - Heisterkamp, Reinhold T1 - Vom Desktop-GIS zur mobilen 3D-Lösung N2 - Dipl.-Ing. Reinhold Heisterkamp - GDS Geo Daten Service GmbH, Borken (Westf.). 8 S. (S. 24-31). Beitrag zum 2. Aachener Softwaretag in der Wasserwirtschaft <2, 2009, Aachen>. Einleitung Web-GIS Leistungsmerkmale von aktuellen Web-GIS Mobile GIS-Lösungen Dreidimensionale GIS-Lösungen KW - Geoinformationssystem KW - Geodatenbank KW - Geodatenhaltung KW - Geoinformationen Y1 - 2009 ER - TY - CHAP A1 - Kraft, Bodo A1 - Wilhelms, Nils T1 - Visual Knowledge Specification for Conceptual Design N2 - Proc. of the 2005 ASCE Intl. Conf. on Computing in Civil Engineering (ICCC 2005) eds. L. Soibelman und F. Pena-Mora, Seite 1-14, ASCE (CD-ROM), Cancun, Mexico, 2005 Current CAD tools are not able to support the fundamental conceptual design phase, and none of them provides consistency analyses of sketches produced by architects. To give architects a greater support at the conceptual design phase, we develop a CAD tool for conceptual design and a knowledge specification tool allowing the definition of conceptually relevant knowledge. The knowledge is specific to one class of buildings and can be reused. Based on a dynamic knowledge model, different types of design rules formalize the knowledge in a graph-based realization. An expressive visual language provides a user-friendly, human readable representation. Finally, consistency analyses enable conceptual designs to be checked against this defined knowledge. In this paper we concentrate on the knowledge specification part of our project. KW - CAD KW - CAD KW - Bauingenieurwesen KW - CAD KW - civil engineering Y1 - 2005 ER - TY - CHAP A1 - Merten, Sabine A1 - Kämper, Klaus-Peter A1 - Brill, Manfred A1 - Picard, Antoni A1 - Cassel, Detlev A1 - Jentsch, Andreas A1 - Rollwa, Markus T1 - Virtuelle Sensor-Fertigung: Hightech mit LabVIEW N2 - Eine neue Generation von Praktika an Hochschulen wächst heran. Moderne Wege beim Verstehen und Erlernen naturwissenschaftlicher Zusammenhänge sowie industrieller Fertigungsprozesse sind gefordert. Das Technologiepraktikum „Virtuelle Sensor- Fertigung“, entwickelt im Verbundprojekt INGMEDIA an den Fachhochschulen Aachen und Zweibrücken, trägt als neuartiges Lern- und Lehrmodul dieser Forderung Rechnung. Die Studierenden lernen einen vollständigen Fertigungsprozess mit Hilfe von virtuellen, in LabVIEW programmierten Maschinen kennen, bevor sie die reale Prozesskette im Reinraum durchführen. N2 - A new generation of university laboratory courses is presently being developed. Modern concepts for the understanding and learning of applied science and industrial fabrication processes are required. The technology course “Fabrication of a microsensor”, developed by the Universities of Applied Sciences Aachen and Zweibrücken in the joint research project INGMEDIA, represents a new approach towards education in high technology production. The students learn the operation of the complex microfabrication line with the help of virtual fabrication machines, programmed in LabVIEW, before they perform the actual process in a genuine clean room. KW - LabVIEW KW - Virtuelle Sensor-Fertigung KW - Fertigungsprozess KW - virtuelle Maschinen KW - virtual sensor fabrication KW - manufacturing process KW - virtual KW - virtual machines Y1 - 2003 ER - TY - CHAP A1 - Dielmann, Klaus-Peter A1 - Velden, Alwin van der T1 - Virtuelle Kraftwerke - Stand der Technik N2 - Ausgangslage, Funktionsprinzip des virtuellen Kraftwerkes, Energiemanagementsysteme (EMS), Einsatzgebiete, Anlagesysteme eines VKW's, Einsatzbereich der verschiedenen dezentralen Energieanlagen, Vorteile des virtuellen Kraftwerkes, Auswirkungen auf das elektrische Netz, Wirtschaftliche Aspekte, Beispielprojekte KW - Virtuelle Kraftwerke Y1 - 2003 ER - TY - CHAP A1 - Merten, Sabine A1 - Conrad, Thorsten A1 - Kämper, Klaus-Peter A1 - Picard, Antoni A1 - Schütze, Andreas T1 - Virtual Technology Labs - an efficient tool for the preparation of hands-on-MEMS-courses in training foundries N2 - Hands-on-training in high technology areas is usually limited due to the high cost for lab infrastructure and equipment. One specific example is the field of MEMS, where investment and upkeep of clean rooms with microtechnology equipment is either financed by production or R&D projects greatly reducing the availability for education purposes. For efficient hands-on-courses a MEMS training foundry, currently used jointly by six higher education institutions, was established at FH Kaiserslautern. In a typical one week course, students manufacture a micromachined pressure sensor including all lithography, thin film and packaging steps. This compact and yet complete program is only possible because participants learn to use the different complex machines in advance via a Virtual Training Lab (VTL). In this paper we present the concept of the MEMS training foundry and the VTL preparation together with results from a scientific evaluation of the VTL over the last three years. KW - Virtuelles Laboratorium KW - Virtuelles Labor KW - Hand-on-training KW - Virtual Technology Lab KW - MEMS ; education and training foundry Y1 - 2006 ER - TY - CHAP A1 - Baader, Fabian A1 - Reiswich, M. A1 - Bartsch, M. A1 - Keller, D. A1 - Tiede, E. A1 - Keck, G. A1 - Demircian, A. A1 - Friedrich, M. A1 - Dachwald, Bernd A1 - Schüller, K. A1 - Lehmann, R. A1 - Chojetzki, R. A1 - Durand, C. A1 - Rapp, L. A1 - Kowalski, Julia A1 - Förstner, R. T1 - VIPER - Student research on extraterrestrical ice penetration technology T2 - Proceedings of the 2nd Symposium on Space Educational Activities N2 - Recent analysis of scientific data from Cassini and earth-based observations gave evidence for a global ocean under a surrounding solid ice shell on Saturn's moon Enceladus. Images of Enceladus' South Pole showed several fissures in the ice shell with plumes constantly exhausting frozen water particles, building up the E-Ring, one of the outer rings of Saturn. In this southern region of Enceladus, the ice shell is considered to be as thin as 2 km, about an order of magnitude thinner than on the rest of the moon. Under the ice shell, there is a global ocean consisting of liquid water. Scientists are discussing different approaches the possibilities of taking samples of water, i.e. by melting through the ice using a melting probe. FH Aachen UAS developed a prototype of maneuverable melting probe which can navigate through the ice that has already been tested successfully in a terrestrial environment. This means no atmosphere and or ambient pressure, low ice temperatures of around 100 to 150K (near the South Pole) and a very low gravity of 0,114 m/s^2 or 1100 μg. Two of these influencing measures are about to be investigated at FH Aachen UAS in 2017, low ice temperature and low ambient pressure below the triple point of water. Low gravity cannot be easily simulated inside a large experiment chamber, though. Numerical simulations of the melting process at RWTH Aachen however are showing a gravity dependence of melting behavior. Considering this aspect, VIPER provides a link between large-scale experimental simulations at FH Aachen UAS and numerical simulations at RWTH Aachen. To analyze the melting process, about 90 seconds of experiment time in reduced gravity and low ambient pressure is provided by the REXUS rocket. In this time frame, the melting speed and contact force between ice and probes are measured, as well as heating power and a two-dimensional array of ice temperatures. Additionally, visual and infrared cameras are used to observe the melting process. Y1 - 2018 SP - 1 EP - 6 ER - TY - CHAP A1 - Jacobs, Stephan T1 - Verwendung von Netzwerkmustern in der Telekommunikationsindustrie : [Vortragsfolien] T2 - Test Patterns - Intelligente Wiederverwendung von Testware : Software-QS-Tag 2007 ; 08. November 2007, Nürnberg N2 - "[...] Der erste Teil des Vortags konzentriert sich auf die bei Ericsson gemachten Erfahrungen. Welche Muster wurden identifiziert, für welche Tests wurden sie eingesetzt. Wie werden diese Muster verwendet, wie werden sie beschrieben und spezifiziert. Und schließlich, wie entsteht eine Art Standardisierung, in der das Wissen über diese Muster als Organisationswissen zur Verfügung steht. Im zweiten Teil des Vortrags werden die bei Ericsson gemachten Erfahrungen verallgemeinert. Die bei Ericsson verwendeten Muster werden auf allgemeine Strukturen übertragen (z.B. Client-Server). Es wird gezeigt, wie die Zuordnung von Testverfahren auf Netzwerkmuster auch in anderen Domänen verwendet wird und welche Vorteile sich damit erzielen lassen." Quelle: http://www.qs-tag.de/fileadmin/software-qs-tag/public/2007/abstract_jacobs.shtml Y1 - 2007 ER - TY - CHAP A1 - Engels, Elmar A1 - Luszczynski, Kai T1 - Vergleichende Untersuchung zur Topologie von zelloptimalen, elektromobilitäts-optimierten Ladungsausgleichsvorrichtungen N2 - Mit freundlicher Genehmigung der Autoren und des Oldenbourg Industrieverlags https://www.oldenbourg-industrieverlag.de/de/9783835633223-33223 erschienen als Beitrag im Tagungsband zur AALE-Tagung 2012. 9. Fachkonferenz 4.-5. Mai 2012, Aachen, Fachhochschule. ISBN 9783835633223 S 6-2. S. 165-174 Zusammenfassung der Autoren: "Abschließend kann festgehalten werden, dass die gesamten durchgeführten Überlegungen von den Messergebnissen der Inbetriebnahme positiv bestätigt werden. Es wird durch diese Topologie eine maximale Systemverfügbarkeit garantiert und die Zellen werden optimal betrieben. Ein Blick in die Zukunft für dieses Projekt zeigt viele Erweiterungs- und Optimierungsaufgaben. So muss der DC/DC-Wandler für einen bidirektionalen Betrieb erweitert werden, um einen Rekuperationsbetrieb zu gewährleisten bzw. die Zellen laden zu können. Dadurch können gleichzeitig die Gleichrichterdioden im Sekundärleistungsteil durch IGBTs oder MOSFETs ersetzt werden. Die voll funktionsfähige Version des DC/DC-Wandlers könnte höchstwahrscheinlich direkt auf die Anschlusspole der Zelle montiert werden, wodurch das Gewicht gesenkt wird. Durch die verringerte Verlustleistung in den Zuleitungen könnte der Wirkungsgrad noch einmal gesteigert werden. KW - Gleichspannungswandler Y1 - 2012 ER - TY - CHAP A1 - Sedlacek, G. A1 - Geßler, A. A1 - Schleser, Markus A1 - Mund, F. A1 - Völling, B. T1 - Verbindungen vorgefertigter Textilbetonbauteile T2 - Textile reinforced structures : proceedings of the 2nd Colloquium on Textile Reinforced Structures (CTRS2), Dresden, Germany, 29.9. - 1.10.2003 Y1 - 2003 SN - 3-86005-386-8 SP - 481 EP - 493 PB - Techn. Univ. CY - Dresden ER - TY - CHAP A1 - Nakagawa, Masaki A1 - Michaux, Frank A1 - Kallweit, Stephan A1 - Maeda, Kazuhiro T1 - Unsteady flow measurements in the wake behind a wind-tunnel car model by using high-speed planar PIV T2 - 11TH International Symposium on Particle Image Velocimetry – PIV15 Santa Barbara, California, September 14-16, 2015 N2 - This study investigates unsteady characteristics of the wake behind a 28%-scale car model in a wind tunnel using highspeed planar particle image velocimetry (PIV). The car model is based on a hatchback passenger car that is known to have relatively high fluctuations in its aerodynamic loads. This study primarily focuses on the lateral motion of the flow on the horizontal plane to determine the effect of the flow motion on the straight-line stability and the initial steering response of the actual car on a track. This paper first compares the flow fields in the wake behind the above mentioned model obtained using conventional and high-speed planar PIV, with sampling frequencies of 8 Hz and 1 kHz, respectively. Large asymmetrically coherent flow structures, which fluctuate at frequencies below 2 Hz, are observed in the results of highspeed PIV measurements, whereas conventional PIV is unable to capture these features of the flow owing to aliasing. This flow pattern with a laterally swaying motion is represented by opposite signs of cross-correlation coefficients of streamwise velocity fluctuations for the two sides of the car model. Effects of two aerodynamic devices that are known to reduce the fluctuation levels of the aerodynamic loads are then extensively investigated. The correlation analyses reveal that these devices indeed reduce the fluctuation levels of the flow and the correlation values around the rear combination-lamp, but it is found that the effects of these devices are different around the c-pillar. Y1 - 2015 ER - TY - CHAP A1 - Engels, Elmar A1 - Gabler, Thomas T1 - Universelle Programmierschnittstelle für Motion-Logic Systeme : Struktur, Funktionen und Anwendung in der Forschung und Lehre N2 - Mit freundlicher Genehmigung der Autoren und des Oldenbourg Industrieverlags https://www.oldenbourg-industrieverlag.de/de/9783835633223-33223 erschienen als Beitrag im Tagungsband zur AALE-Tagung 2012. 9. Fachkonferenz 4.-5. Mai 2012, Aachen, Fachhochschule. ISBN 9783835633223 S 2-1 S. 37-46 Original-Abstract der Autoren: "Dieser Artikel beschreibt eine universelle Programmierschnittstelle zur Entwicklung von Motion-Logic Applikationen für industrielle Motion-Controller. Sie ermöglicht die Entwicklung von Software mit modernen Hochsprachen, wie C/C++. Visual Basic, C#, Java, Objective-Cund visuellen Programmiersprachen, wie LabVIEW in Koexistenz mit klassischen Programmiersprachen für speicherprogrammierbare Steuerungen nach IEC 61131-3. Daraus ergeben sich neue Möglichkeiten industrielle Antriebs- und Steuerungssysteme mit ihrem IT-Umfeld zu verbinden." KW - Speicherprogrammierte Steuerung KW - Motion-Logic System KW - SPS KW - IndraMotion Y1 - 2012 ER - TY - CHAP A1 - Tran, Thanh Ngoc A1 - Staat, Manfred ED - Onate, E. T1 - Uncertain multimode failure and limit analysis of shells T2 - 11th World Congress on Computational Mechanics (WCCM XI) ; 5th European Conference on Computational Mechanics (ECCM V) ; 6th European Conference on Computational Fluid Dynamics (ECFD VI) ; July 20-25, 2014, Barcelona Y1 - 2014 SP - 1 EP - 12 ER -