TY  - CHAP
A1  - Wild, Dominik
A1  - Czupalla, Markus
A1  - Förstner, Roger
T1  - Modeling, prediction and test of additive manufactured integral structures with embedded lattice and phase change material applying Infused Thermal Solutions (ITS)
T2  - ICES104: Advances in Thermal Control Technology
N2  - Infused Thermal Solutions (ITS) introduces a method for passive thermal control to stabilize structural components thermally without active heating and cooling systems, but with phase change material (PCM) for thermal energy storage (TES), in combination with lattice - both embedded in additive manufactured functional structures. In this ITS follow-on paper a thermal model approach and associated predictions are presented, related on the ITS functional breadboards developed at FH Aachen. Predictive TES by PCM is provided by a specially developed ITS PCM subroutine, which is applicable in ESATAN. The subroutine is based on the latent heat storage (LHS) method to numerically embed thermo-physical PCM behavior. Furthermore, a modeling approach is introduced to numerically consider the virtual PCM/lattice nodes within the macro-encapsulated PCM voids of the double wall ITS design. Related on these virtual nodes, in-plane and out-of-plane conductive links are defined. The recent additive manufactured ITS breadboard series are thermally cycled in the thermal vacuum chamber, both with and without embedded PCM. Related on breadboard hardware tests, measurement results are compared with predictions and are subsequently correlated. The results of specific simulations and measurements are presented. Recent predictive results of star tracker analyses are also presented in ICES-2021-106, based on this ITS PCM subroutine.
KW  - latent heat
KW  - thermo-physical
KW  - lattice
KW  - ESATAN
KW  - subroutine
KW  - PCM
KW  - ITS
Y1  - 2021
N1  - 50th International Conference on Environmental Systems, 12-15 July 2021, held virtually
PB  - Texas Tech University
CY  - Lubbock, Tex.
ER  - 
TY  - JOUR
A1  - Schopen, Oliver
A1  - Shah, Neel
A1  - Esch, Thomas
A1  - Shabani, Bahman
T1  - Critical quantitative evaluation of integrated health management methods for fuel cell applications
JF  - International Journal of Hydrogen Energy
N2  - Online fault diagnostics is a crucial consideration for fuel cell systems, particularly in mobile applications, to limit downtime and degradation, and to increase lifetime. Guided by a critical literature review, in this paper an overview of Health management systems classified in a scheme is presented, introducing commonly utilised methods to diagnose FCs in various applications. In this novel scheme, various Health management system methods are summarised and structured to provide an overview of existing systems including their associated tools. These systems are classified into four categories mainly focused on model-based and non-model-based systems. The individual methods are critically discussed when used individually or combined aimed at further understanding their functionality and suitability in different applications. Additionally, a tool is introduced to evaluate methods from each category based on the scheme presented. This tool applies the technique of matrix evaluation utilising several key parameters to identify the most appropriate methods for a given application. Based on this evaluation, the most suitable methods for each specific application are combined to build an integrated Health management system.
KW  - Fuel cell
KW  - Health management system
KW  - Online diagnostic
KW  - Fault detection
KW  - Non-model-based Evaluation
Y1  - 2024
U6  - https://doi.org/10.1016/j.ijhydene.2024.05.156
SN  - 0360-3199
VL  - 70
SP  - 370
EP  - 388
PB  - Elsevier
CY  - Amsterdam
ER  - 
TY  - JOUR
A1  - Czupalla, Markus
T1  - Ein Garten im Weltraum
JF  - Spektrum der Wissenschaft
Y1  - 2017
PB  - Spektrum-der-Wiss.-Verl.-Ges.
CY  - Heidelberg
ER  - 
TY  - GEN
A1  - Eccleston, Paul
A1  - Drummond, Rachel
A1  - Middleton, Kevin
A1  - Bishop, Georgia
A1  - Caldwell, Andrew
A1  - Desjonqueres, Lucile
A1  - Tosh, Ian
A1  - Cann, Nick
A1  - Crook, Martin
A1  - Hills, Matthew
A1  - Pearson, Chris
A1  - Simpson, Caroline
A1  - Stamper, Richard
A1  - Tinetti, Giovanna
A1  - Pascale, Enzo
A1  - Swain, Mark
A1  - Holmes, Warren A.
A1  - Wong, Andre
A1  - Puig, Ludovic
A1  - Pilbratt, Göran
A1  - Linder, Martin
A1  - Boudin, Nathalie
A1  - Ertel, Hanno
A1  - Gambicorti, Lisa
A1  - Halain, Jean-Philippe
A1  - Pace, Emanuele
A1  - Vilardell, Francesc
A1  - Gómez, José M.
A1  - Colomé, Josep
A1  - Amiaux, Jérôme
A1  - Cara, Christophe
A1  - Berthe, Michel
A1  - Moreau, Vincent
A1  - Morgante, Gianluca
A1  - Malaguti, Giuseppe
A1  - Alonso, Gustavo
A1  - Álvarez, Javier P.
A1  - Ollivier, Marc
A1  - Philippon, Anne
A1  - Hellin, Marie-Laure
A1  - Roose, Steve
A1  - Frericks, Martin
A1  - Krijger, Matthijs
A1  - Rataj, Miroslaw
A1  - Wawer, Piotr
A1  - Skup, Konrad
A1  - Sobiecki, Mateusz
A1  - Christian Jessen, Niels
A1  - Møller Pedersen, Søren
A1  - Hargrave, Peter
A1  - Griffin, Matt
A1  - Ottensamer, Roland
A1  - Hunt, Thomas
A1  - Rust, Duncan
A1  - Saleh, Aymen
A1  - Winter, Berend
A1  - Focardi, Mauro
A1  - Da Deppo, Vania
A1  - Zuppella, Paola
A1  - Czupalla, Markus
ED  - Lystrup, Makenzie
ED  - Perrin, Marshall D.
ED  - Batalha, Natalie
ED  - Siegler, Nicholas
ED  - Tong, Edward C.
T1  - The ARIEL payload: A technical overview
T2  - Space Telescopes and Instrumentation 2020: Optical, Infrared, and Millimeter Wave
N2  - The Atmospheric Remote-Sensing Infrared Exoplanet Large-survey, ARIEL, has been selected to be the next (M4) medium class space mission in the ESA Cosmic Vision programme. From launch in 2028, and during the following 4 years of operation, ARIEL will perform precise spectroscopy of the atmospheres of ~1000 known transiting exoplanets using its metre-class telescope. A three-band photometer and three spectrometers cover the 0.5 µm to 7.8 µm region of the electromagnetic spectrum. This paper gives an overview of the mission payload, including the telescope assembly, the FGS (Fine Guidance System) - which provides both pointing information to the spacecraft and scientific photometry and low-resolution spectrometer data, the ARIEL InfraRed Spectrometer (AIRS), and other payload infrastructure such as the warm electronics, structures and cryogenic cooling systems.
KW  - Exoplanet
KW  - Spectroscopy
KW  - Transit
KW  - Atmospheres
KW  - Payload
Y1  - 2020
U6  - https://doi.org/10.1117/12.2561478
N1  - Space Telescopes and Instrumentation 2020: Optical, Infrared, and Millimeter Wave, 14–22 December 2020, Online Only, United States
VL  - 11443
SP  - 114430Z
PB  - SPIE
CY  - Washington
ER  - 
TY  - GEN
A1  - Reiswich, Martin
A1  - Brandt, Hannes
A1  - Czupalla, Markus
T1  - Passive thermal control by integration of phase change material into additively manufactured structures
T2  - E2. 47th Student conference
N2  - Optical Instruments require an extremely stable thermal surrounding to prevent loss of data quality by misalignments of the instrument components resulting from material deformation due to temperature f luctuations (e.g. from solar intrusion). Phase Change Material (PCM) can be applied as a thermal damper to achieve a more uniform temperature distribution. The challenge of this method is, among others, the integration of PCM into affected areas. If correctly designed, incoming heat is latently absorbed during phase change of the PCM, i.e. the temperature of a structure remains almost constant. In a cold phase, the heat during phase change is released again latently until the PCM returns to its original state of aggregation. Thus, the structure is thermally stabilized. At FH Aachen– University of Applied Sciences research is conducted to apply PCM directly into the structures of affected components (baffles, optical benches, electronic boxes, etc.). Through the application of Additive Manufacturing, the necessary voids are directly printed into these structures and filled later with PCM. Additive Manufacturing enables complex structures that would not have been possible with conservative manufacturing methods. A corresponding Breadboard was developed and manufactured by Selective Laser Melting (SLM). The current state of research includes the handling and analysis of the Breadboard, tests and a correlation of the thermal model. The results have shown analytically and practically that it is possible to use PCM as an integral part of the structure as a thermal damper. The results serve as a basis for the further development of the technology, which should maximize performance and enable the integration of PCM into much more complex structures.
Y1  - 2019
N1  - 70th International Astronautical Congress, 21. - 25. Oktober 2019, Washington D.C., United States
ER  - 
TY  - GEN
A1  - Gamgami, Farid
A1  - Czupalla, Markus
A1  - Garcia, Antonio
A1  - Agnolon, David
T1  - From planetary transits to spacecraft design: achieving PLATO’s pointing performance
T2  - A7. Symposium on technological Requirement for future space astronomy and solar-system science missions
N2  - In the last decades, several hundred exoplanets could be detected thanks to space-based observatories, namely CNES’ COROT and NASA’s Kepler. To expand this quest ESA plans to launch CHEOPS as the f irst small class mission in the cosmic visions program (S1) and PLATO as the 3rd medium class mission, so called M3 . PLATO’s primary objective is the detection of Earth like Exoplanets orbiting solar type stars in the habitable zone and characterisation of their bulk properties. This is possible by precise lightcurve measurement via 34 cameras. That said it becomes obvious that accurate pointing is key to achieve the required signal to noise ratio for positive transit detection. The paper will start with a comprehensive overview of PLATO’s mission objectives and mission architecture. Hereafter, special focus will be devoted to PLATO’s pointing requirements. Understanding the very nature of PLATO’s pointing requirements is essential to derive a design baseline to achieve the required performance. The PLATO frequency domain is of particular interest, ranging from 40 mHz to 3 Hz. Due to the very different time-scales involved, the spectral pointing requirement is decomposed into a high frequency part dominated by the attitude control system and the low frequency part dominated by the thermo-elastic properties of the spacecraft’s configuration. Both pose stringent constraints on the overall design as well as technology properties to comply with the derived requirements and thus assure a successful mission.
Y1  - 2016
N1  - 67th International Astronautical Congress, 26. - 30. September 2016, Guadalajara, Mexico
ER  - 
TY  - CHAP
A1  - Bung, Daniel Bernhard
A1  - Langohr, Phillip
A1  - Waldenberger, Lisa
ED  - Habersack, Helmut
ED  - Tritthart, Michael
T1  - Influence of cycle number in CFD studies of labyrinth weirs
T2  - Proceedings of the 40th IAHR World Congress (Vienna, 2023)
N2  - The major advantage of labyrinth weirs over linear weirs is hydraulic efficiency. In hydraulic modeling efforts, this strength contrasts with limited pump capacity as well as limited computational power for CFD simulations. For the latter, reducing the number of investigated cycles can significantly reduce necessary computational time. In this study, a labyrinth weir with different cycle numbers was investigated. The simulations were conducted in FLOW-3D HYDRO as a Large Eddy Simulation. With a mean deviation of 1.75 % between simulated discharge coefficients and literature design equations, a reasonable agreement was found. For downstream conditions, overall consistent results were observed as well. However, the orientation of labyrinth weirs with a single cycle should be chosen carefully under consideration of the individual research purpose.
KW  - CFD
KW  - Large Eddy Simulation
KW  - Labyfrinth weirs
Y1  - 2023
SN  - 978-90-833476-1-5
U6  - https://doi.org/10.3850/978-90-833476-1-5_iahr40wc-p0531-cd
SN  - L 2521-7119 (online)
N1  - Vienna, Austria, from August 21 to 25, 2023
PB  - International Association for Hydro-Environment Engineering and Research (IAHR)
CY  - Madrid
ER  - 
TY  - JOUR
A1  - Droop, Philipp
A1  - Chen, Shaohuang
A1  - Radford, Melissa J.
A1  - Paulßen, Elisabeth
A1  - Gates, Byron D.
A1  - Reilly, Raymond M.
A1  - Radchenko, Valery
A1  - Hoehr, Cornelia
T1  - Synthesis of 197m/gHg labelled gold nanoparticles for targeted radionuclide therapy
JF  - Radiochimica Acta
N2  - Meitner-Auger-electron emitters have a promising potential for targeted radionuclide therapy of cancer because of their short range and the high linear energy transfer of Meitner-Auger-electrons (MAE). One promising MAE candidate is 197m/gHg with its half-life of 23.8 h and 64.1 h, respectively, and high MAE yield. Gold nanoparticles (AuNPs) that are labelled with 197m/gHg could be a helpful tool for radiation treatment of glioblastoma multiforme when infused into the surgical cavity after resection to prevent recurrence. To produce such AuNPs, 197m/gHg was embedded into pristine AuNPs. Two different syntheses were tested starting from irradiated gold containing trace amounts of 197m/gHg. When sodium citrate was used as reducing agent, no 197m/gHg labelled AuNPs were formed, but with tannic acid, 197m/gHg labeled AuNPs were produced. The method was optimized by neutralizing the pH (pH = 7) of the Au/197m/gHg solution, which led to labelled AuNPs with a size of 12.3 ± 2.0 nm as measured by transmission electron microscopy. The labelled AuNPs had a concentration of 50 μg (gold)/mL with an activity of 151 ± 93 kBq/mL (197gHg, time corrected to the end of bombardment).
KW  - 197m/gHg
KW  - Gold nanoparticle (AuNP)
KW  - Meitner-Auger-electron (MAE)
KW  - Targeted radionuclide therapy (TRT)
Y1  - 2023
U6  - https://doi.org/10.1515/ract-2023-0144
SN  - 2193-3405
VL  - 111
IS  - 10
SP  - 773
EP  - 779
PB  - De Gruyter
CY  - Berlin [u.a.]
ER  - 
TY  - JOUR
A1  - Mues genannt Koers, Lucas
A1  - McNeil, S. W.
A1  - Radchenko, V.
A1  - Paulßen, Elisabeth
A1  - Hoehr, Cornelia
T1  - Production of Co-58m in a siphon-style liquid target on a medical cyclotron
N2  - We present the production of 58mCo on a small, 13 MeV medical cyclotron utilizing a siphon style liquid target system. Different concentrated iron(III)-nitrate solutions of natural isotopic distribution were irradiated at varying initial pressures and subsequently separated by solid phase extraction chromatography. The radio cobalt (58m/gCo and 56Co) was successfully produced with saturation activities of (0.35 ± 0.03) MBq μA−1 for 58mCo with a separation recovery of (75 ± 2) % of cobalt after one separation step utilizing LN-resin.
Y1  - 2023
U6  - https://doi.org/10.1016/j.apradiso.2023.110734
SN  - 0969-8043
VL  - 195
IS  - Art. 110734
PB  - Elsevier
CY  - Amsterdam
ER  - 
TY  - JOUR
A1  - Mues genannt Koers, Lucas
A1  - Prevost, David
A1  - Paulßen, Elisabeth
A1  - Hoehr, Cornelia
T1  - Density reduction effects on the production of [11C]CO2 in Nb-body targets on a medical cyclotron
N2  - Medical isotope production of 11C is commonly performed in gaseous targets. The power deposition of the proton beam during the irradiation decreases the target density due to thermodynamic mixing and can cause an increase of penetration depth and divergence of the proton beam. In order to investigate the difference how the target-body length influences the operation conditions and the production yield, a 12 cm and a 22 cm Nb-target body containing N2/O2 gas were irradiated using a 13 MeV proton cyclotron. It was found that the density reduction has a large influence on the pressure rise during irradiation and the achievable radioactive yield. The saturation activity of [11C]CO2 for the long target (0.083 Ci/μA) is about 10% higher than in the short target geometry (0.075 Ci/μA).
Y1  - 2023
U6  - https://doi.org/10.1016/j.apradiso.2023.110911
VL  - 199
IS  - Art. 110911
PB  - Elsevier
CY  - Amsterdam
ER  - 
TY  - THES
A1  - Bung, Daniel Bernhard
T1  - Imaging techniques for investigation of free-surface flows in hydraulic laboratories
N2  - This thesis aims at the presentation and discussion of well-accepted and new
imaging techniques applied to different types of flow in common hydraulic
engineering environments. All studies are conducted in laboratory conditions and
focus on flow depth and velocity measurements. Investigated flows cover a wide
range of complexity, e.g. propagation of waves, dam-break flows, slightly and fully
aerated spillway flows as well as highly turbulent hydraulic jumps.
Newimagingmethods are compared to different types of sensorswhich are frequently
employed in contemporary laboratory studies. This classical instrumentation as well
as the general concept of hydraulic modeling is introduced to give an overview on
experimental methods.
Flow depths are commonly measured by means of ultrasonic sensors, also known as
acoustic displacement sensors. These sensors may provide accurate data with high
sample rates in case of simple flow conditions, e.g. low-turbulent clear water flows.
However, with increasing turbulence, higher uncertainty must be considered.
Moreover, ultrasonic sensors can provide point data only, while the relatively large
acoustic beam footprint may lead to another source of uncertainty in case of
relatively short, highly turbulent surface fluctuations (ripples) or free-surface
air-water flows. Analysis of turbulent length and time scales of surface fluctuations
from point measurements is also difficult. Imaging techniques with different
dimensionality, however, may close this gap. It is shown in this thesis that edge
detection methods (known from computer vision) may be used for two-dimensional
free-surface extraction (i.e. from images taken through transparant sidewalls in
laboratory flumes). Another opportunity in hydraulic laboratory studies comes with
the application of stereo vision. Low-cost RGB-D sensors can be used to gather
instantaneous, three-dimensional free-surface elevations, even in flows with very
high complexity (e.g. aerated hydraulic jumps). It will be shown that the uncertainty
of these methods is of similar order as for classical instruments.
Particle Image Velocimetry (PIV) is a well-accepted and widespread imaging
technique for velocity determination in laboratory conditions. In combination with
high-speed cameras, PIV can give time-resolved velocity fields in 2D/3D or even as
volumetric flow fields. PIV is based on a cross-correlation technique applied to small
subimages of seeded flows. The minimum size of these subimages defines the
maximum spatial resolution of resulting velocity fields. A derivative of PIV for
aerated flows is also available, i.e. the so-called Bubble Image Velocimetry (BIV). This
thesis emphasizes the capacities and limitations of both methods, using relatively
simple setups with halogen and LED illuminations. It will be demonstrated that
PIV/BIV images may also be processed by means of Optical Flow (OF) techniques.
OF is another method originating from the computer vision discipline, based on the
assumption of image brightness conservation within a sequence of images. The
Horn-Schunck approach, which has been first employed to hydraulic engineering
problems in the studies presented herein, yields dense velocity fields, i.e. pixelwise
velocity data. As discussed hereinafter, the accuracy of OF competes well with PIV
for clear-water flows and even improves results (compared to BIV) for aerated flow
conditions. In order to independently benchmark the OF approach, synthetic images
with defined turbulence intensitiy are used.
Computer vision offers new opportunities that may help to improve the
understanding of fluid mechanics and fluid-structure interactions in laboratory
investigations. In prototype environments, it can be employed for obstacle detection
(e.g. identification of potential fish migration corridors) and recognition (e.g. fish
species for monitoring in a fishway) or surface reconstruction (e.g. inspection of
hydraulic structures). It can thus be expected that applications to hydraulic
engineering problems will develop rapidly in near future. Current methods have not
been developed for fluids in motion. Systematic future developments are needed to
improve the results in such difficult conditions.
Y1  - 2023
U6  - https://doi.org/10.25926/BUW/0-172
ER  - 
TY  - JOUR
A1  - Kleefeld, Andreas
A1  - Pieronek, J.
T1  - Elastic transmission eigenvalues and their computation via the method of fundamental solutions
JF  - Applicable Analysis
N2  - A stabilized version of the fundamental solution method to catch ill-conditioning effects is investigated with focus on the computation of complex-valued elastic interior transmission eigenvalues in two dimensions for homogeneous and isotropic media. Its algorithm can be implemented very shortly and adopts to many similar partial differential equation-based eigenproblems as long as the underlying fundamental solution function can be easily generated. We develop a corroborative approximation analysis which also implicates new basic results for transmission eigenfunctions and present some numerical examples which together prove successful feasibility of our eigenvalue recovery approach.
KW  - elastic scattering
KW  - method of fundamental solutions
KW  - Interior transmission eigenvalues
Y1  - 2020
U6  - https://doi.org/10.1080/00036811.2020.1721473
SN  - 1563-504X
VL  - 100
IS  - 16
SP  - 3445
EP  - 3462
PB  - Taylore & Francis
CY  - London
ER  - 
TY  - CHAP
A1  - Mayntz, Joscha
A1  - Keimer, Jona
A1  - Dahmann, Peter
A1  - Hille, Sebastian
A1  - Stumpf, Eike
A1  - Fisher, Alex
A1  - Dorrington, Graham
T1  - Electrical Drive and Regeneration in General Aviation Flight with Propellers
T2  - Deutscher Luft- und Raumfahrtkongress 2020
N2  - Electric flight has the potential for a more sustainable and energy-saving way of aviation compared to fossil fuel aviation. The electric motor can be used as a generator inflight to regenerate energy during descent. Three different approaches to regenerating with electric propeller powertrains are proposed in this paper. The powertrain is to be set up in a wind tunnel to determine the propeller efficiency in both working modes as well as the noise emissions. Furthermore, the planned flight tests are discussed. In preparation for these tests, a yaw stability analysis is performed with the result that the aeroplane is controllable during flight and in the most critical failure case. The paper shows the potential for inflight regeneration and addresses the research gaps in the dual role of electric powertrains for propulsion and regeneration of general aviation aircraft.
KW  - Propeller Aerodynamics
KW  - Flight Tests
KW  - Flight Mechanics
KW  - Electrical Flight
KW  - Inflight Regeneration, Recuperation
Y1  - 2022
U6  - https://doi.org/10.25967/530100
N1  - Deutscher Luft- und Raumfahrtkongress 2020, 1. - 3. September 2020, Online
PB  - DGLR
CY  - Bonn
ER  - 
TY  - GEN
A1  - Mayntz, Joscha
A1  - Keimer, Jona
A1  - Tegtmeyer, Philipp
A1  - Dahmann, Peter
A1  - Hille, Sebastian
A1  - Stumpf, Eike
A1  - Fisher, Alex
A1  - Dorrington, Graham
T1  - Aerodynamic Investigation on Efficient Inflight Transition of a Propeller from Propulsion to Regeneration Mode
T2  - AIAA SCITECH 2022 Forum
N2  - This paper discusses a new way of inflight power regeneration for electric or hybrid-electric driven general aviation aircraft with one powertrain for both configurations. Three different approaches for the shift from propulsion to regeneration mode are analyzed. Numerical cal-culation and wind tunnel results are compared and show the highest regeneration potential for the "Windmill" approach, where the propeller blades are flipped, and rotation is reversed. A combination of all regeneration approaches for a realistic flight mission is discussed.
Y1  - 2021
U6  - https://doi.org/10.2514/6.2022-0546
N1  - AIAA SCITECH 2022 Forum, January 3-7, 2022, San Diego, CA & Virtual
PB  - AIAA
CY  - Reston, Va.
ER  - 
TY  - JOUR
A1  - Saretzki, Charlotte
A1  - Bergmann, Ole
A1  - Dahmann, Peter
A1  - Janser, Frank
A1  - Keimer, Jona
A1  - Machado, Patricia
A1  - Morrison, Audry
A1  - Page, Henry
A1  - Pluta, Emil
A1  - Stübing, Felix
A1  - Küpper, Thomas
T1  - Are small airplanes safe with regards to COVID-19 transmission?
JF  - Journal of Travel Medicine
Y1  - 2021
U6  - https://doi.org/10.1093/jtm/taab105
SN  - 1708-8305
VL  - 28
IS  - 7
PB  - Oxford University Press
CY  - Oxford
ER  - 
TY  - CHAP
A1  - Treuling, Clemens
A1  - Czarnecki, Christian
A1  - Wolf, Martin
T1  - Projekt WiLMo – Wirtschaftsinformatik Lehr- und Lernmodule
T2  - Angewandte Forschung in der Wirtschaftsinformatik 2023 : Tagungsband zur 36. AKWI-Jahrestagung
N2  - Die potenziellen Auswirkungen der Digitalisierung auf die Lehre sind seit langem Gegenstand ausführlicher Diskussionen innerhalb der Wirtschaftsinformatik (WI) (z. B. in Auth et al. 2021, Barton et al. 2019, Klotz et al. 2019). Nicht zuletzt der in nahezu allen Wirtschaftszweigen bestehende Mangel an qualifizierten Fachkräften lenkt den Diskurs auf einen verbesserten Zugang zu Bildung und gleichen Bildungschancen. Aus dieser Vision heraus und dem Schub der Digitalisierung entstehen Bildungskonzepte wie Open Educational Resources (OER), die gesellschaftlichen Problemen, wie dem des Fachkräftemangels, entgegenwirken sollen. Im Rahmen dieses Kurzbeitrags wird das Projekt WiLMo - "Wirtschaftsinformatik Lehr- und Lernmodule" vorgestellt. WiLMo wird im Rahmen von OERContent.nrw unter Beteiligung von sechs Hochschulen entwickelt und gefördert. Alle Projektbeteiligten arbeiten gemeinsam daran, einheitliche digitale Lehr- und Lernmaterialien im OER-Format für die Kernmodule der Wirtschaftsinformatik zu entwickeln und in garantiert hoher Qualität zur Verfügung zu stellen.
KW  - Wirtschaftsinformatik
KW  - Open Educational Resources (OER)
KW  - WiLMo
Y1  - 2023
N1  - 36. AKWI-Jahrestagung, 11.09.2023 bis 13.09.2023, ausgerichtet von der Technischen Hochschule Wildau
SP  - 161
EP  - 169
ER  - 
TY  - GEN
A1  - Keimer, Jona
A1  - Girbig, Leo
A1  - Mayntz, Joscha
A1  - Tegtmeyer, Philipp
A1  - Wendland, Frederik
A1  - Dahman, Peter
A1  - Fisher, Alex
A1  - Dorrington, Graham
T1  - Flight mission optimization for eco-efficiency in consideration of electric regeneration and atmospheric conditions
T2  - AIAA AVIATION 2022 Forum
N2  - The development and operation of hybrid or purely electrically powered aircraft in regional air mobility is a significant challenge for the entire aviation sector. This technology is expected to lead to substantial advances in flight performance, energy efficiency, reliability, safety, noise reduction, and exhaust emissions. Nevertheless, any consumed energy results in heat or carbon dioxide emissions and limited electric energy storage capabilities suppress commercial use. Therefore, the significant challenges to achieving eco-efficient aviation are increased aircraft efficiency, the development of new energy storage technologies, and the optimization of flight operations. Two major approaches for higher eco-efficiency are identified: The first one, is to take horizontal and vertical atmospheric motion phenomena into account. Where, in particular, atmospheric waves hold exciting potential. The second one is the use of the regeneration ability of electric aircraft. The fusion of both strategies is expected to improve efficiency. The objective is to reduce energy consumption during flight while not neglecting commercial usability and convenient flight characteristics. Therefore, an optimized control problem based on a general aviation class aircraft has to be developed and validated by flight experiments. The formulated approach enables a development of detailed knowledge of the potential and limitations of optimizing flight missions, considering the capability of regeneration and atmospheric influences to increase efficiency and range.
Y1  - 2022
U6  - https://doi.org/10.2514/6.2022-4118
N1  - AIAA AVIATION 2022 Forum, June 27-July 1, 2022 Chicago, IL & Virtual
PB  - AIAA
CY  - Reston, Va.
ER  - 
TY  - BOOK
A1  - Czarnecki, Christian
ED  - Czarnecki, Christian
ED  - Lübbe, Alexander
ED  - Meister, Vera G.
ED  - Müller, Christian
ED  - Steglich, Mike
ED  - Walther, Mathias
T1  - Angewandte Forschung in der Wirtschaftsinformatik 2023 : Tagungsband zur 36. AKWI-Jahrestagung
N2  - Beiträge der Fachtagung „Angewandte Forschung in der Wirtschaftsinformatik – Zukunft gestalten“ im Rahmen der 36. Jahrestagung des Arbeitskreises Wirtschaftsinformatik an Hochschulen für Angewandte Wissenschaften (AKWI) vom 11. bis 13.09.2023 an der Technischen Hochschule Wildau
Y1  - 2023
U6  - https://doi.org/10.15771/1794
N1  - 36. AKWI-Jahrestagung, 11.09.2023 bis 13.09.2023, ausgerichtet von der Technischen Hochschule Wildau
ER  - 
TY  - JOUR
A1  - Bung, Daniel Bernhard
T1  - Kamerabasierte Fließtiefen- und Geschwindigkeitsmessungen
JF  - Wasserwirtschaft
N2  - In der wasserbaulichen Forschung werden neben klassischen Messinstrumenten zunehmend kamerabasierte Verfahren genutzt. Diese erlauben neben der Bestimmung von Fließgeschwindigkeiten auch die Detektion der freien Wasseroberfläche oder zeitliche Vermessung von Kolken. Durch die hohen räumlichen und zeitlichen Auflösungen, welche neueste Kamerasensoren liefern, können neue Erkenntnisse in turbulenten, komplexen Strömungen gewonnen werden. Auch in der Praxis können diese Verfahren mit geringem Aufwand wichtige Daten liefern.
KW  - Wasserbau
KW  - Architektur
KW  - Wasserwirtschaft
KW  - Deutschland
Y1  - 2024
SN  - 0043-0978
VL  - 114
IS  - 4
SP  - 47
EP  - 53
PB  - Springer Vieweg
CY  - Wiesbaden
ER  - 
TY  - CHAP
A1  - Schult, Prince Garcia
A1  - Losse, Ann-Kathrin
A1  - Czarnecki, Christian
A1  - Sultanow, Eldar
T1  - Proposing a Framework to address the Sustainable Development Goals
T2  - EnviroInfo 2023
N2  - Reducing poverty, protecting the planet, and improving life on earth for everyone are the essential goals of the "2030 Agenda for Sustainable Development"committed by the United Nations (UN). Achieving those goals will require technological innovation as well as their implementation in almost all areas of our business and day-to-day life. This paper proposes a high-level framework that collects and structures different uses cases addressing the goals defined by the UN. Hence, it contributes to the discussion by proposing technical innovations that can be used to achieve those goals. As an example, the goal "Climate Actionïs discussed in detail by describing use cases related to tackling biodiversity loss in order to conservate ecosystems.
Y1  - 2023
SN  - 978-3-88579-736-4
U6  - https://doi.org/10.18420/env2023-022
SN  - 1617-5468
N1  - EnviroInfo 2023, 11. - 23. October 2023, Garching, Germany
SP  - 243
EP  - 249
PB  - GI - Gesellschaft für Informatik
CY  - Bonn
ER  -