TY - JOUR A1 - Bergmann, Ole A1 - Möhren, Felix A1 - Braun, Carsten A1 - Janser, Frank T1 - On the influence of elasticity on swept propeller noise JF - AIAA SCITECH 2023 Forum N2 - High aerodynamic efficiency requires propellers with high aspect ratios, while propeller sweep potentially reduces noise. Propeller sweep and high aspect ratios increase elasticity and coupling of structural mechanics and aerodynamics, affecting the propeller performance and noise. Therefore, this paper analyzes the influence of elasticity on forward-swept, backward-swept, and unswept propellers in hover conditions. A reduced-order blade element momentum approach is coupled with a one-dimensional Timoshenko beam theory and Farassat's formulation 1A. The results of the aeroelastic simulation are used as input for the aeroacoustic calculation. The analysis shows that elasticity influences noise radiation because thickness and loading noise respond differently to deformations. In the case of the backward-swept propeller, the location of the maximum sound pressure level shifts forward by 0.5 °, while in the case of the forward-swept propeller, it shifts backward by 0.5 °. Therefore, aeroacoustic optimization requires the consideration of propeller deformation. Y1 - 2023 U6 - https://doi.org/10.2514/6.2023-0210 N1 - Session: Propeller, Open Rotor, and Rotorcraft Noise II AIAA SCITECH 2023 Forum, 23-27 January 2023, National Harbor, MD & Online PB - AIAA CY - Reston, Va. ER - TY - GEN A1 - Hille, Sebastian A1 - Stumpf, Eike A1 - Mayntz, Joscha A1 - Dahmann, Peter T1 - Prediction of sound exposure caused by a landing motor glider with recuperating propellers T2 - AIAA SCITECH 2023 Forum N2 - This paper presents an approach to predicting the sound exposure on the ground caused by a landing aircraft with recuperating propellers. The noise source along the trajectory of a flight specified for a steeper approach is simulated based on measurements of sound power levels and additional parameters of a single propeller placed in a wind tunnel. To validate the measured data/measurement results, these simulations are also supported by overflight measurements of a test aircraft. It is shown that the simple source models of propellers do not provide fully satisfactory results since the sound levels are estimated too low. Nevertheless, with a further reference comparison, margins for an acceptable increase in the sound power level of the aircraft on its now steeper approach path could be estimated. Thus, in this case, a +7 dB increase in SWL would not increase the SEL compared to the conventional approach within only 2 km ahead of the airfield. Y1 - 2023 U6 - https://doi.org/10.2514/6.2023-0211 N1 - AIAA SCITECH 2023 Forum, 23-27 January 2023, National Harbor, Md & Online PB - AIAA CY - Reston, Va. ER - TY - CHAP A1 - Möhren, Felix A1 - Bergmann, Ole A1 - Janser, Frank A1 - Braun, Carsten T1 - On the determination of harmonic propeller loads T2 - AIAA SCITECH 2023 Forum N2 - Dynamic loads significantly impact the structural design of propeller blades due to fatigue and static strength. Since propellers are elastic structures, deformations and aerodynamic loads are coupled. In the past, propeller manufacturers established procedures to determine unsteady aerodynamic loads and the structural response with analytical steady-state calculations. According to the approach, aeroelastic coupling primarily consists of torsional deformations. They neglect bending deformations, deformation velocities, and inertia terms. This paper validates the assumptions above for a General Aviation propeller and a lift propeller for urban air mobility or large cargo drones. Fully coupled reduced-order simulations determine the dynamic loads in the time domain. A quasi-steady blade element momentum approach transfers loads to one-dimensional finite beam elements. The simulation results are in relatively good agreement with the analytical method for the General Aviation propeller but show increasing errors for the slender lift propeller. The analytical approach is modified to consider the induced velocities. Still, inertia and velocity proportional terms play a significant role for the lift propeller due to increased elasticity. The assumption that only torsional deformations significantly impact the dynamic loads of propellers is not valid. Adequate determination of dynamic loads of such designs requires coupled aeroelastic simulations or advanced analytical procedures. Y1 - 2023 U6 - https://doi.org/10.2514/6.2023-2404 N1 - AIAA SCITECH 2023 Forum, 23-27 January 2023, National Harbor, Md & Online PB - AIAA ER - TY - THES A1 - Mok, Pia Peixia T1 - Flowcean Qi : a gentle Reminder to take a deep breath. N2 - Atmen tut jeder, automatisch. Es wird nicht auf die Ausführung geachtet. Doch was, wenn nur ein wenig Feinschliff an unserer Atmung bereits Großes für unsere Gesundheit bewirkt? Von etlichen unterschiedlichen Studien wurde bezeugt, dass Atmung und Empfinden eins sind. Das persönliche Empfinden ist unser Portal zur Außenwelt. Die Art wie wir auf äußerliche Reize reagieren, wie achtsam wir im Tun und Denken sind, spiegelt unsere Innenwelt und körperliches Wohlbefinden wieder. FLOWCEAN QI dient dazu, Stress- und Angststörungen im Alltagsleben für Berufstätige mit hohem Stressfaktor zu reduzieren. Vor allem, um das Gesundheitssystem zu entlasten und die Psyche der Menschen gesund wieder aufzubauen. Sind Berufstätige viel gelassener, steigen auch Leistung und Produktivität. Es ist immer wichtig, die Kernursache von Problemen zu finden und zu lösen. So können auch vielerlei andere auf die Psyche zurückzuführende Probleme der Gesellschaft gelöst werden. FLOWCEAN QI agiert durch modernste Technologie aktiv mit dem Nutzer. Die KI-Assistenz gestaltet das Lernen der Atemtechniken spaßiger, was wiederum den Lerneffekt verbessert. Der Beamer wird im Innenbereich platziert und der Tracker begleitet einen unterwegs und zeichnet die Datenanalyse auf. Für mehr Datenschutz ist das Armband ein reines offline Produkt. Förmlich sollte es dem Nutzer nah sein, naturverbunden, vertrauenswürdig und beruhigend wirken. FLOWCEAN QI basiert gestalterisch auf eine antike japanische Philosophie namens „Kintsugi“. Nach der japanischen Philosophie Kintsugi werden zerbrochene Teegläser wiederzusammengeklebt statt weggeworfen. Die in Teile getrennten Elemente werden glatt und geschmeidig wieder zusammengefügt. Sie formen ein neues Ganzes, dass die Schönheit des Originals meist übertrifft. Die Ästhetik hinter „Kintsugi“ nennt man „Wabi-Sabi“. Es bedeutet, die Schönheit im Vergänglichen, Alten oder Fehlerhaften zu verstehen. Die Philosophie dahinter wird metaphorisch auf das Design abgebildet und auf unsere Gesundheit übertragen. Statt letztere zu ignorieren, schenken wir ihr unsere volle Aufmerksamkeit. Ziel der Produkte ist, uns stets an sie zu erinnern, sodass wir täglich an unserem Wohlbefinden arbeiten können. KW - Atmen KW - KI KW - Stress KW - Japan KW - Angststörungen Y1 - 2023 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER - TY - THES A1 - Namakiravesh, Ehsan T1 - Coupé Nr. 13 N2 - Coupé Nr. 13 ist eine kurze Animation über ein Zugcoupé mit 6 individuellen Passagieren und den 5 Stufen der Kommunikationsentwicklung zwischen ihnen. Die Passagiere des "Coupé Nummer 13" werden zu ihrem wahren Ich, wenn sie sich gegenseitig die Kofferklappen öffnen. Doch dieses Offen-Sein ist gar nicht so einfach. Es fühlt sich anfangs verletzlich an, psychologisch nackt und meist ängstlich. Aber diese Verletzlichkeit ist aus psychologischer Sicht der Schlüssel zu engen Beziehungen. Wahre Verbundenheit entsteht nur, wenn man den Weg zur Schattenseite des anderen findet – indem man sie so sieht und annimmt, wie sie wirklich sind. In der Tat bewundern und respektieren wir meistens die Verletzlichkeit anderer Menschen. Wir sehen sie in der Regel als ein Zeichen von Stärke und Mut – nicht von Schwäche. KW - Animation KW - Kommunikation KW - Zug KW - Schattenseite KW - Schein Y1 - 2023 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER - TY - CHAP A1 - Viehmann, Tarik A1 - Limpert, Nicolas A1 - Hofmann, Till A1 - Henning, Mike A1 - Ferrein, Alexander A1 - Lakemeyer, Gerhard ED - Eguchi, Amy ED - Lau, Nuno ED - Paetzel-Prüsmann, Maike ED - Wanichanon, Thanapat T1 - Winning the RoboCup logistics league with visual servoing and centralized goal reasoning T2 - RoboCup 2022: Robot World Cup XXV N2 - The RoboCup Logistics League (RCLL) is a robotics competition in a production logistics scenario in the context of a Smart Factory. In the competition, a team of three robots needs to assemble products to fulfill various orders that are requested online during the game. This year, the Carologistics team was able to win the competition with a new approach to multi-agent coordination as well as significant changes to the robot’s perception unit and a pragmatic network setup using the cellular network instead of WiFi. In this paper, we describe the major components of our approach with a focus on the changes compared to the last physical competition in 2019. Y1 - 2023 SN - 978-3-031-28468-7 (Print) SN - 978-3-031-28469-4 (Online) U6 - https://doi.org/https://doi.org/10.1007/978-3-031-28469-4_25 N1 - Robot World Cup, RoboCup 2022. 17. July 2023. Bangkok, Thailand. Part of the Lecture Notes in Computer Science book series (LNAI,volume 13561) SP - 300 EP - 312 PB - Springer CY - Cham ER - TY - JOUR A1 - Pfaff, Raphael T1 - Braking distance prediction for vehicle consist in low-speed on-sight operation: a Monte Carlo approach JF - Railway Engineering Science N2 - The first and last mile of a railway journey, in both freight and transit applications, constitutes a high effort and is either non-productive (e.g. in the case of depot operations) or highly inefficient (e.g. in industrial railways). These parts are typically managed on-sight, i.e. with no signalling and train protection systems ensuring the freedom of movement. This is possible due to the rather short braking distances of individual vehicles and shunting consists. The present article analyses the braking behaviour of such shunting units. For this purpose, a dedicated model is developed. It is calibrated on published results of brake tests and validated against a high-definition model for low-speed applications. Based on this model, multiple simulations are executed to obtain a Monte Carlo simulation of the resulting braking distances. Based on the distribution properties and established safety levels, the risk of exceeding certain braking distances is evaluated and maximum braking distances are derived. Together with certain parameters of the system, these can serve in the design and safety assessment of driver assistance systems and automation of these processes. KW - Freight rail KW - Shunting KW - Braking curves KW - Brake set-up KW - Driver assistance system Y1 - 2023 U6 - https://doi.org/10.1007/s40534-023-00303-7 SN - 2662-4753 (eISSN) SN - 2662-4745 (Print) VL - 31 IS - 2 SP - 135 EP - 144 PB - SpringerOpen ER - TY - CHAP A1 - Engelmann, Ulrich M. A1 - Baumann, Martin ED - Thomann, Hermann ED - Träger, Thomas T1 - Moderationsexpertise für QMBs – die Methoden T2 - Qualitätsmanagement in Dienstleistungsunternehmen N2 - Damit Sie als Moderator effektiv und professionell moderieren können, sollten Sie die entsprechenden Methoden kennen. Mit den richtigen Methoden können Sie Diskussionen leiten, Konflikte lösen, die Teilnehmer motivieren und dafür sorgen, dass die Ziele der Veranstaltung erreicht werden. Außerdem helfen sie Ihnen, eine positive Atmosphäre zu schaffen und das Interesse der Teilnehmer zu halten. In diesem zweiten Beitrag der mehrteiligen Serie lernen Sie die grundsätzlichen Methoden kennen, um erfolgreiche Teamsitzungen, Arbeitsgruppentreffen, Kick-offs und Meetings durchzuführen. Y1 - 2023 SN - 978-3-8249-0473-0 SP - Kapitel 08631 PB - TÜV-Verlag CY - Köln ER - TY - CHAP A1 - Engelmann, Ulrich M. A1 - Baumann, Martin ED - Lindinger, Markus ED - Bartsch, Oliver T1 - Moderationsexpertise – die Methoden T2 - IT-Servicemanagement N2 - Damit Sie als Moderator effektiv und professionell moderieren können, sollten Sie die entsprechenden Methoden kennen. Mit den richtigen Methoden können Sie Diskussionen leiten, Konflikte lösen, die Teilnehmer motivieren und dafür sorgen, dass die Ziele der Veranstaltung erreicht werden. Außerdem helfen sie Ihnen, eine positive Atmosphäre zu schaffen und das Interesse der Teilnehmer zu halten. In diesem zweiten Beitrag der mehrteiligen Serie lernen Sie die grundsätzlichen Methoden kennen, um erfolgreiche Teamsitzungen, Arbeitsgruppentreffen, Kick-offs und Meetings durchzuführen. Y1 - 2023 SN - 978-3-8249-1154-7 SP - Kapitel 05531 PB - TÜV-Verlag CY - Köln ET - 54. Update ER - TY - BOOK A1 - Kurz, Melanie A1 - Schwer, Thilo T1 - Design für Spiel, Spaß, Spannung: Gestaltung von Artefakten zum spielerischen Handeln / herausgegeben von Melanie Kurz und Thilo Schwer T3 - Schriften / Gesellschaft für Designgeschichte N2 - Die kulturgeschichtlichen Stationen des Spielens vom Beginn der Industrialisierung bis zur Jahrtausendwende werden sowohl aus dem Blickwinkel der Designgeschichte als auch aus dem der Game Studies betrachtet. Die Bandbreite der Themen reicht von der Bauhaus-Wurfpuppe bis zur Barbie, vom Japonismus bis zur Pixelgrafik, von der grafischen Raumillusion zu 3D-Umgebungen und Interaktionsgestaltung, vom Brettspiel bis zum Kriegsspielzeug, von den Utopien der beginnenden Neuzeit bis zu merkantilen Absichten digitaler Spielkonzepte. Y1 - 2023 SN - 978-3-89986-396-3 N1 - Band 6 PB - avedition CY - Stuttgart ET - 1. Auflage ER - TY - THES A1 - Thiele, Jana T1 - Düsseldorfer Schauspielhaus : „Entwicklung eines neuen Erscheinungsbildes“ N2 - In der heutigen digitalisierten und individualisierten Welt spielt das Theater weiterhin eine bedeutende Rolle als kulturelle Institution und als Ort des künstlerischen Ausdrucks. Dabei ist einer der wichtigsten Aspekte die Bewegung. Sie findet auf der Bühne in jeglicher Form statt – Tanz, Gestik, Mimik, die Schritte der Schauspieler:innen, Sprünge, Armbewegungen. All diese unterschiedlichen Arten von Bewegung sind ausschlaggebend für die Wirkung der Texte und Stücke. Für das neue Erscheinungsbild des Düsseldorfer Schauspielhauses wurde dieser Bewegungsaspekt in ein spannendes, modernes und übersichtliches Corporate Design übersetzt. Das Ergebnis: Sonderzeichen, die „Bewegung“ aufgreifen und entsprechend „verformt“ wurden. Durch ihr verändertes Aussehen spiegeln sie diese Bewegung abstrahiert wider und führen abwechslungsreich durch die verschiedenen Medien. KW - Schauspiel KW - Theater KW - Bewegung KW - Sonderzeichen KW - Schauspielhaus Y1 - 2023 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER - TY - THES A1 - Thiem, Antonia T1 - Entwicklung eines neuen Corporate Design für ein Museum mit dem Schwerpunkt Lichtkunst N2 - Weithin leuchtend – tief unter der Erde strahlend: Das »Zentrum für internationale Lichtkunst« in Unna ist ein »Unikat« unter den Kunstmuseen weltweit, da das Museum das Einzige ist, welches sich ausschließlich der zeitgenössischen Lichtkunst widmet. Seit 2001 erstreckt sich die Sammlung von 21 dauerhaften Werken in einem großzügigen Kellergewölbe. Viele der Lichtinstallationen wurden eigens für die Räumlichkeiten konzipiert und sind sowohl in ihrem technischen, als auch ästhetischen und perspektivischen Auftritt unverwechselbar. Die Zielsetzung des Projektes ist es, ein systematisches und einheitliches Erscheinungsbild, welches crossmedial eingesetzt werden kann, zu erarbeiten. Des Weiteren soll die Thematik Lichtkunst in dem Corporate Design aufgegriffen und widergespiegelt werden, sodass die Berührungspunkte des Publikums spannungsvoll und einprägend aufgenommen werden. KW - Lichtkunst KW - Kunst KW - Corporate Design KW - Museum KW - Lichtkunst Museum Y1 - 2023 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER - TY - THES A1 - Von Dallwitz, Sophia T1 - (un)said : Offene Gespräche über Alltagssexismus N2 - Unsaid ist ein didaktisches Starterkit für offene Gespräche über Alltagssexismus mit einem Schwerpunkt auf sexueller Belästigung im öffentlichen Raum. Es beinhaltet mehrere Schritte – die Broschüre bietet euch das benötigte Wissen für einen konstruktiven Diskurs. Zusätzlich sind Karten mit Fragen enthalten, die dazu anregen, sexistische Denkmuster und Verhaltensweisen im Alltag zu erkennen und zu reflektieren. Und schließlich zeigt es konkrete Aktionen auf, wie ihr selbst aktiv werden und euch gegen sexistisches Verhalten aussprechen könnt. Das Kit ist darauf ausgerichtet, dass Lehrende an weiterführenden Schulen es in ihren Unterricht integrieren können. Ihr könnt es jedoch genauso gut unter euren Freund*innen, Kolleg*innen oder anderen Interessierten nutzen, um eure Meinungen und Erfahrungen miteinander zu teilen. Unsaid ist ein weiterer Schritt, um Alltagssexismus zu bekämpfen und eine Gesellschaft zu schaffen, in der Gleichberechtigung und Respekt selbstverständlich sind. KW - Typografie KW - Starterkit KW - Broschüre KW - Leitfaden KW - Diskussionskarten Y1 - 2023 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER - TY - THES A1 - Waliszewska, Laura T1 - Werkstatt voller Historie N2 - Das Buch „Werkstatt voller Historie“ gibt einen Einblick in das Handwerk der Restaurierung und Konservierung. Wir leben in einer Gesellschaft, die von Konsum und schneller Verfügbarkeit geprägt ist. Produkte werden in Massen produziert, genutzt und oft schon nach kurzer Zeit wieder weggeworfen. Durch diese Mentalität der Wegwerfgesellschaft werden die Ressourcen unserer Erde erschöpft, und Umweltprobleme werden immer größer. Deshalb ist es wichtig, sich intensiv mit der Bewahrung von Kulturgut auseinanderzusetzen. Durch die Verwendung von Illustrationen und visuellen Darstellungen erleichtert das Buch die Kommunikation. Dadurch kann der Restaurierungsprozess einfacher verstanden werden. Mit dem Projekt soll das Interesse geweckt und über die Grundlagen und Herausforderungen der Restaurierung aufgeklärt werden. KW - Restaurierung KW - Konservierung KW - Werkstatt KW - Historie KW - Handwerk Y1 - 2023 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER - TY - THES A1 - Wamper, Lukas T1 - Bachelorzeit N2 - Die Bachelorarbeit behandelt die Konzeption und Produktion der Sendung "Bachelorzeit". Ziel ist es, eine innovative Plattform für junge Zuschauer:innen zu schaffen und Einblicke in das Leben und die Themen der Stadt Aachen zu geben. Die Arbeit umfasst den gesamten Produktionsprozess inklusive der Einbindung der Zuschauer:innen und der visuellen Gestaltung. Die erfolgreiche Umsetzung ermöglicht eine ansprechende und nahbare Atmosphäre für ein jüngeres Publikum. KW - Visuelle Gestaltung KW - Sendungskonzeption KW - Produktion KW - Innovation KW - Stadt Aachen Y1 - 2023 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER - TY - CHAP A1 - Nierle, Elisabeth A1 - Pieper, Martin T1 - Measuring social impacts in engineering education to improve sustainability skills T2 - European Society for Engineering Education (SEFI) N2 - In times of social climate protection movements, such as Fridays for Future, the priorities of society, industry and higher education are currently changing. The consideration of sustainability challenges is increasing. In the context of sustainable development, social skills are crucial to achieving the United Nations Sustainable Development Goals (SDGs). In particular, the impact that educational activities have on people, communities and society is therefore coming to the fore. Research has shown that people with high levels of social competence are better able to manage stressful situations, maintain positive relationships and communicate effectively. They are also associated with better academic performance and career success. However, especially in engineering programs, the social pillar is underrepresented compared to the environmental and economic pillars. In response to these changes, higher education institutions should be more aware of their social impact - from individual forms of teaching to entire modules and degree programs. To specifically determine the potential for improvement and derive resulting change for further development, we present an initial framework for social impact measurement by transferring already established approaches from the business sector to the education sector. To demonstrate the applicability, we measure the key competencies taught in undergraduate engineering programs in Germany. The aim is to prepare the students for success in the modern world of work and their future contribution to sustainable development. Additionally, the university can include the results in its sustainability report. Our method can be applied to different teaching methods and enables their comparison. KW - Social impact measurement KW - Key competences KW - Sustainable engineering education KW - Future skills Y1 - 2023 U6 - https://doi.org/10.21427/QPR4-0T22 N1 - 51st Annual Conference of the European Society for Engineering Education, Technological University Dublin, 10th-14th September, 2023 N1 - Corresponding Author: Elisabeth Nierle ER - TY - BOOK A1 - Lauth, Jakob T1 - Physical chemistry in a nutshell: Basics for engineers and scientists N2 - This book is based on a multimedia course for biological and chemical engineers, which is designed to trigger students' curiosity and initiative. A solid basic knowledge of thermodynamics and kinetics is necessary for understanding many technical, chemical, and biological processes. The one-semester basic lecture course was divided into 12 workshops (chapters). Each chapter covers a practically relevant area of physical chemistry and contains the following didactic elements that make this book particularly exciting and understandable: - Links to Videos at the start of each chapter as preparation for the workshop - Key terms (in bold) for further research of your own - Comprehension questions and calculation exercises with solutions as learning checks - Key illustrations as simple, easy-to-replicate blackboard pictures Humorous cartoons for each workshop (by Faelis) additionally lighten up the text and facilitate the learning process as a mnemonic. To round out the book, the appendix includes a summary of the most popular experiments in basic physical chemistry courses, as well as suggestions for designing workshops with exhibits, experiments, and "questions of the day." Suitable for students minoring in chemistry; chemistry majors are sure to find this slimmed-down, didactically valuable book helpful as well. The book is excellent for self-study. KW - Physical chemistry KW - Thermodynamics as minor KW - Physical chemistry starters KW - Minor chemistry KW - Physical chemistry basics Y1 - 2023 SN - 978-3-662-67636-3 (Softcover) SN - 978-3-662-67637-0 (eBook) U6 - https://doi.org/10.1007/978-3-662-67637-0 PB - Springer CY - Berlin ER - TY - CHAP A1 - Engelmann, Ulrich M. A1 - Baumann, Martin ED - Herbig, Nicola ED - Poppelreuter, Stefan T1 - Moderationsexpertise für QMBs – Onlinemoderation T2 - Qualitätsmanagement im Gesundheitswesen N2 - Damit Sie auch in den immer häufiger werdenden Onlineveranstaltungen als Moderator gut bestehen, sollten Sie wissen, was bei der Onlinemoderation im Besonderen zu beachten ist. In diesem dritten Teil der Beitragsserie erfahren Sie, warum online anders als offline ist. Die technischen Möglichkeiten werden vorgestellt und auch wie diese zu nutzen sind. Schließlich erhalten Sie Tipps, die Sie beim Sprechen online beachten sollten. Y1 - 2023 SN - 978-3-8249-0714-4 SP - Kapitel 10816 PB - TÜV-Verlag CY - Köln ER - TY - CHAP A1 - Engelmann, Ulrich M. ED - Lindinger, Markus ED - Bartsch, Oliver T1 - Moderationsexpertise – Onlinemoderation T2 - IT-Servicemanagement N2 - Damit Sie auch in den immer häufiger werdenden Onlineveranstaltungen als Moderator gut bestehen, sollten Sie wissen, was bei der Onlinemoderation im Besonderen zu beachten ist. In diesem dritten Teil der Beitragsserie erfahren Sie, warum online anders als offline ist. Die technischen Möglichkeiten werden vorgestellt und auch wie diese zu nutzen sind. Schließlich erhalten Sie Tipps, die Sie beim Sprechen online beachten sollten. Y1 - 2023 SN - 978-3-8249-1154-7 SP - Kapitel 05532 PB - TÜV-Verlag CY - Köln ER - TY - THES A1 - Glück, Anna T1 - Entwicklung eines Erscheinungsbildes für ein Unternehmen im Bereich Bioenergiefassaden N2 - Nachhaltige Technologien, die Ressourcen schonen und Energie gewinnen, erlangen zunehmend an Bedeutung im urbanen Raum. Diese Bachelorarbeit befasst sich mit der Entwicklung eines Corporate Designs für ein Unternehmen, das sich auf die Fertigung und Planung von Bioenergiefassaden spezialisiert hat. Das Unternehmen sorgt durch seinen Fokus auf nachhaltige Energiegewinnung und effiziente Gebäudeplanung für die Verbesserung der ökologischen Herausforderungen. Das Ziel des neuen Corporate Designs ist es, die komplexe Thematik der Bioenergiefassaden der Zielgruppe effektiv zu vermitteln und ihr Interesse für dieses System zu wecken. Dabei werden Illustrationen und Infografiken eingesetzt, um die Technologie verständlich darzustellen, die positiven Umweltauswirkungen sowie Vorteile der Bioenergiefassaden deutlich hervorzuheben und mehr Umsetzungen zu erzielen. KW - Bioenergiefassaden KW - Erscheinungsbild KW - Nachhaltigkeit KW - Technologie KW - Algen Y1 - 2023 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER - TY - CHAP A1 - Neth, Jannik A1 - Schuba, Marko A1 - Brodkorb, Karsten A1 - Neugebauer, Georg A1 - Höner, Tim A1 - Hack, Sacha T1 - Digital forensics triage app for android T2 - ARES '23: Proceedings of the 18th International Conference on Availability, Reliability and Security N2 - Digital forensics of smartphones is of utmost importance in many criminal cases. As modern smartphones store chats, photos, videos etc. that can be relevant for investigations and as they can have storage capacities of hundreds of gigabytes, they are a primary target for forensic investigators. However, it is exactly this large amount of data that is causing problems: extracting and examining the data from multiple phones seized in the context of a case is taking more and more time. This bears the risk of wasting a lot of time with irrelevant phones while there is not enough time left to analyze a phone which is worth examination. Forensic triage can help in this case: Such a triage is a preselection step based on a subset of data and is performed before fully extracting all the data from the smartphone. Triage can accelerate subsequent investigations and is especially useful in cases where time is essential. The aim of this paper is to determine which and how much data from an Android smartphone can be made directly accessible to the forensic investigator – without tedious investigations. For this purpose, an app has been developed that can be used with extremely limited storage of data in the handset and which outputs the extracted data immediately to the forensic workstation in a human- and machine-readable format. KW - Android KW - Digital triage KW - Triage-app Y1 - 2023 SN - 9798400707728 U6 - https://doi.org/10.1145/3600160.3605017 N1 - ARES 2023: The 18th International Conference on Availability, Reliability and Security. August 29 - September 1, 2023. Benevento, Italy. PB - ACM ER - TY - JOUR A1 - Dellmann, Sophia Florence A1 - Glorius, J. A1 - Litvinov, Yu A. A1 - Reifarth, R. A1 - Al-Khasawneh, Kafa A1 - Aliotta, M. A1 - Bott, L. A1 - Brückner, Benjamin A1 - Bruno, C. G. A1 - Chen, Ruijiu A1 - Davinson, T. A1 - Dickel, T. A1 - Dillmann, Iris A1 - Dmytriev, D. A1 - Erbacher, P. A1 - Freire-Fernández, D. A1 - Forstner, Oliver A1 - Geissel, H. A1 - Göbel, K. A1 - Griffin, Christopher J. A1 - Grisenti, R. A1 - Gumberidze, Alexandre A1 - Haettner, Emma A1 - Hagmann, Siegbert A1 - Heil, M. A1 - Heß, R. A1 - Hillenbrand, P.-M. A1 - Joseph, R. A1 - Jurado, B. A1 - Kozhuharov, Christophor A1 - Kulikov, I. A1 - Löher, Bastian A1 - Langer, Christoph A1 - Leckenby, Guy A1 - Lederer-Woods, C. A1 - Lestinsky, M. A1 - Litvinov, S. A. A1 - Lorenz, B. A. A1 - Lorenz, E. A1 - Marsh, J. A1 - Menz, Esther Babette A1 - Morgenroth, T. A1 - Petridis, N. A1 - Pibernat, Jerome A1 - Popp, U. A1 - Psaltis, Athanasios A1 - Sanjari, Shahab A1 - Scheidenberger, C. A1 - Sguazzin, M. A1 - Sidhu, Ragandeep Singh A1 - Spillmann, Uwe A1 - Steck, M. A1 - Stöhlker, T. A1 - Surzhykov, A. A1 - Swartz, J. A. A1 - Törnqvist, H. A1 - Varga, L. A1 - Vescovi, Diego A1 - Weick, H. A1 - Weigand, M. A1 - Woods, P. A1 - Xing, Y. A1 - Yamaguchi, Taiyo T1 - Proton capture on stored radioactive ¹¹⁸Te ions JF - EPJ Web of Conferences N2 - Experimental determination of the cross sections of proton capture on radioactive nuclei is extremely difficult. Therefore, it is of substantial interest for the understanding of the production of the p-nuclei. For the first time, a direct measurement of proton-capture cross sections on stored, radioactive ions became possible in an energy range of interest for nuclear astrophysics. The experiment was performed at the Experimental Storage Ring (ESR) at GSI by making use of a sensitive method to measure (p,γ) and (p,n) reactions in inverse kinematics. These reaction channels are of high relevance for the nucleosyn-thesis processes in supernovae, which are among the most violent explosions in the universe and are not yet well understood. The cross section of the ¹¹⁸Te(p,γ) reaction has been measured at energies of 6 MeV/u and 7 MeV/u. The heavy ions interacted with a hydrogen gas jet target. The radiative recombination process of the fully stripped ¹¹⁸Te ions and electrons from the hydrogen target was used as a luminosity monitor. An overview of the experimental method and preliminary results from the ongoing analysis will be presented. Y1 - 2023 U6 - https://doi.org/10.1051/epjconf/202327911018 SN - 2100-014X N1 - Volume 279, 2023. Nuclear Physics in Astrophysics – X (NPA-X 2022). VL - 279 IS - Article Number: 11018 SP - 1 EP - 5 PB - EDP Sciences ER - TY - CHAP A1 - Arndt, Tobias A1 - Conzen, Max A1 - Elsen, Ingo A1 - Ferrein, Alexander A1 - Galla, Oskar A1 - Köse, Hakan A1 - Schiffer, Stefan A1 - Tschesche, Matteo T1 - Anomaly detection in the metal-textile industry for the reduction of the cognitive load of quality control workers T2 - PETRA '23: Proceedings of the 16th International Conference on PErvasive Technologies Related to Assistive Environments N2 - This paper presents an approach for reducing the cognitive load for humans working in quality control (QC) for production processes that adhere to the 6σ -methodology. While 100% QC requires every part to be inspected, this task can be reduced when a human-in-the-loop QC process gets supported by an anomaly detection system that only presents those parts for manual inspection that have a significant likelihood of being defective. This approach shows good results when applied to image-based QC for metal textile products. KW - Datasets KW - Neural networks KW - Anomaly detection KW - Quality control KW - Process optimization Y1 - 2023 SN - 9798400700699 U6 - https://doi.org/10.1145/3594806.3596558 N1 - PETRA '23: Proceedings of the 16th International Conference on PErvasive Technologies Related to Assistive Environments, Corfu, Greece, July 5 - 7, 2023 SP - 535 EP - 542 PB - ACM ER - TY - CHAP A1 - Zähl, Philipp M. A1 - Theis, Sabine A1 - Wolf, Martin A1 - Köhler, Klemens ED - Chen, Jessie Y. C. ED - Fragomeni, Gino T1 - Teamwork in software development and what personality has to do with it - an overview T2 - Virtual, Augmented and Mixed Reality N2 - Due to the increasing complexity of software projects, software development is becoming more and more dependent on teams. The quality of this teamwork can vary depending on the team composition, as teams are always a combination of different skills and personality types. This paper aims to answer the question of how to describe a software development team and what influence the personality of the team members has on the team dynamics. For this purpose, a systematic literature review (n=48) and a literature search with the AI research assistant Elicit (n=20) were conducted. Result: A person’s personality significantly shapes his or her thinking and actions, which in turn influences his or her behavior in software development teams. It has been shown that team performance and satisfaction can be strongly influenced by personality. The quality of communication and the likelihood of conflict can also be attributed to personality. KW - Teamwork KW - Software KW - Personality KW - Performance KW - Elicit Y1 - 2023 SN - 978-3-031-35633-9 (Print) SN - 978-3-031-35634-6 (Online) U6 - https://doi.org/10.1007/978-3-031-35634-6_10 N1 - Virtual, Augmented and Mixed Reality: 15th International Conference. VAMR 2023. Held as Part of the 25th HCI International Conference. HCII 2023. Copenhagen, Denmark. July 23–28, 2023. SP - 130 EP - 153 PB - Springer CY - Cham ER - TY - JOUR A1 - Bertz, Morten A1 - Molinnus, Denise A1 - Schöning, Michael Josef A1 - Homma, Takayuki T1 - Real-time monitoring of H₂O₂ sterilization on individual bacillus atrophaeus spores by optical sensing with trapping Raman spectroscopy JF - Chemosensors N2 - Hydrogen peroxide (H₂O₂), a strong oxidizer, is a commonly used sterilization agent employed during aseptic food processing and medical applications. To assess the sterilization efficiency with H₂O₂, bacterial spores are common microbial systems due to their remarkable robustness against a wide variety of decontamination strategies. Despite their widespread use, there is, however, only little information about the detailed time-resolved mechanism underlying the oxidative spore death by H₂O₂. In this work, we investigate chemical and morphological changes of individual Bacillus atrophaeus spores undergoing oxidative damage using optical sensing with trapping Raman microscopy in real-time. The time-resolved experiments reveal that spore death involves two distinct phases: (i) an initial phase dominated by the fast release of dipicolinic acid (DPA), a major spore biomarker, which indicates the rupture of the spore’s core; and (ii) the oxidation of the remaining spore material resulting in the subsequent fragmentation of the spores’ coat. Simultaneous observation of the spore morphology by optical microscopy corroborates these mechanisms. The dependence of the onset of DPA release and the time constant of spore fragmentation on H₂O₂ shows that the formation of reactive oxygen species from H₂O₂ is the rate-limiting factor of oxidative spore death. KW - DPA (dipicolinic acid) KW - sterilization KW - Bacillus atrophaeus spores KW - optical trapping KW - Raman spectroscopy KW - optical sensor setup Y1 - 2023 U6 - https://doi.org/10.3390/chemosensors11080445 SN - 2227-9040 N1 - This article belongs to the Special Issue "Biosensors and Chemical Sensors for Food and Healthcare Monitoring—Celebrating the 10th Anniversary" VL - 8 IS - 11 PB - MDPI CY - Basel ER - TY - JOUR A1 - Wendlandt, Tim A1 - Koch, Claudia A1 - Britz, Beate A1 - Liedek, Anke A1 - Schmidt, Nora A1 - Werner, Stefan A1 - Gleba, Yuri A1 - Vahidpour, Farnoosh A1 - Welden, Melanie A1 - Poghossian, Arshak A1 - Schöning, Michael Josef T1 - Facile Purification and Use of Tobamoviral Nanocarriers for Antibody-Mediated Display of a Two-Enzyme System JF - Viruses N2 - Immunosorbent turnip vein clearing virus (TVCV) particles displaying the IgG-binding domains D and E of Staphylococcus aureus protein A (PA) on every coat protein (CP) subunit (TVCVPA) were purified from plants via optimized and new protocols. The latter used polyethylene glycol (PEG) raw precipitates, from which virions were selectively re-solubilized in reverse PEG concentration gradients. This procedure improved the integrity of both TVCVPA and the wild-type subgroup 3 tobamovirus. TVCVPA could be loaded with more than 500 IgGs per virion, which mediated the immunocapture of fluorescent dyes, GFP, and active enzymes. Bi-enzyme ensembles of cooperating glucose oxidase and horseradish peroxidase were tethered together on the TVCVPA carriers via a single antibody type, with one enzyme conjugated chemically to its Fc region, and the other one bound as a target, yielding synthetic multi-enzyme complexes. In microtiter plates, the TVCVPA-displayed sugar-sensing system possessed a considerably increased reusability upon repeated testing, compared to the IgG-bound enzyme pair in the absence of the virus. A high coverage of the viral adapters was also achieved on Ta2O5 sensor chip surfaces coated with a polyelectrolyte interlayer, as a prerequisite for durable TVCVPA-assisted electrochemical biosensing via modularly IgG-assembled sensor enzymes. KW - biosensor KW - horseradish peroxidase (HRP) KW - glucose oxidase (GOx) KW - enzyme cascade KW - turnip vein clearing virus (TVCV) KW - tobacco mosaic virus (TMV) Y1 - 2023 U6 - https://doi.org/doi.org/10.3390/v15091951 SN - 1999-4915 N1 - This article belongs to the Special Issue "Tobamoviruses 2023" VL - 9 IS - 15 PB - MDPI CY - Basel ER - TY - GEN A1 - Steuer-Dankert, Linda A1 - Berg-Postweiler, Julia A1 - Leicht-Scholten, Carmen T1 - One does not fit all: applying anti-bias trainings in academia T2 - Twenty-third international conference on diversity in organizations, communities & nations June 22 - 23, 2023 Toronto Metropolitan University, Rogers Communication Centre Toronto, Canada N2 - Anti-bias trainings are increasingly demanded and practiced in academia and industry to increase employees’ sensitivity to discrimination, racism, and diversity. Under the heading of “Diversity Management”, anti-bias trainings are mainly offered as one-off workshops intending to raise awareness of unconscious biases, create a diversity-affirming corporate culture, awake awareness of the potential of diversity, and ultimately enable the reflection of diversity in development processes. However, coming from childhood education, research and scientific articles on the sustainable effectiveness of anti-bias in adulthood, especially in academia, are very scarce. In order to fill this research gap, the paper explores how sustainable the effects of individual anti-bias trainings on the behavior of participants are. In order to investigate this, participant observation in a qualitative pre-post setting was conducted, analyzing anti-bias trainings in an academic context. Two observers actively participated in the training sessions and documented the activities and reflection processes of the participants. Overall, the results question the effectiveness of single anti-bias trainings and show that a target-group adaptive approach is mandatory due to the background of the approach in early childhood education. Therefore, it can be concluded that anti-bias work needs to be adapted to the target group’s needs and reality of life. Furthermore, the study reveals that single anti-bias trainings must be embedded in a holistic diversity management approach to stimulate sustainable reflection processes among the target group. This paper is one of the first to scientifically evaluate anti-bias training effectiveness, especially in engineering sciences and the university context. KW - Academia KW - Engineering Habitus KW - Organizational Culture KW - Diversity Management KW - Anti-Bias Y1 - 2023 ER - TY - CHAP A1 - Eggert, Mathias A1 - Zähl, Philipp M. A1 - Wolf, Martin R. A1 - Haase, Martin ED - Cooper, Kendra M.L. ED - Bucchiarone, Antonio T1 - Applying leaderboards for quality improvement in software development projects T2 - Software Engineering for Games in Serious Contexts N2 - Software development projects often fail because of insufficient code quality. It is now well documented that the task of testing software, for example, is perceived as uninteresting and rather boring, leading to poor software quality and major challenges to software development companies. One promising approach to increase the motivation for considering software quality is the use of gamification. Initial research works already investigated the effects of gamification on software developers and come to promising. Nevertheless, a lack of results from field experiments exists, which motivates the chapter at hand. By conducting a gamification experiment with five student software projects and by interviewing the project members, the chapter provides insights into the changing programming behavior of information systems students when confronted with a leaderboard. The results reveal a motivational effect as well as a reduction of code smells. KW - Leaderboard KW - Gamification KW - Software testing KW - Software development Y1 - 2023 SN - 978-3-031-33337-8 (Print) SN - 978-3-031-33338-5 (Online) U6 - https://doi.org/10.1007/978-3-031-33338-5_11 SP - 243 EP - 263 PB - Springer CY - Cham ER - TY - INPR A1 - Bornheim, Tobias A1 - Niklas, Grieger A1 - Blaneck, Patrick Gustav A1 - Bialonski, Stephan T1 - Preprint: Speaker attribution in German parliamentary debates with QLoRA-adapted large language models T2 - Journal for Language Technology and Computational Linguistics N2 - The growing body of political texts opens up new opportunities for rich insights into political dynamics and ideologies but also increases the workload for manual analysis. Automated speaker attribution, which detects who said what to whom in a speech event and is closely related to semantic role labeling, is an important processing step for computational text analysis. We study the potential of the large language model family Llama 2 to automate speaker attribution in German parliamentary debates from 2017-2021. We fine-tune Llama 2 with QLoRA, an efficient training strategy, and observe our approach to achieve competitive performance in the GermEval 2023 Shared Task On Speaker Attribution in German News Articles and Parliamentary Debates. Our results shed light on the capabilities of large language models in automating speaker attribution, revealing a promising avenue for computational analysis of political discourse and the development of semantic role labeling systems. Y1 - 2023 U6 - https://doi.org/10.48550/arXiv.2309.09902 N1 - Veröffentlichte Version verfügbar unter: https://doi.org/10.21248/jlcl.37.2024.244 ER - TY - THES A1 - Thoennißen, Amber Katharina T1 - Boys will be boys N2 - "boys will be boys" erkundet bestehende Meinungen zum Thema Männlichkeit und versucht Alternativen zu finden: Wege, die Männlichkeit gehen und Richtungen, in die sich Männlichkeit verändern kann. Auf 236 Seiten wird das Thema von so vielen Seiten wie irgendwie möglich beleuchtet. Es gibt sowohl sehr persönliche, subjektive Beschäftigung mit dem Thema als auch eine objektive, wissenschaftliche Herangehensweise. Das Buch ist vor allem mit typografischen Elementen gestaltet worden, wobei in Inhalt und Typografie viel Wert auf Niedrigschwelligkeit gelegt wurde. Außen ist ein partieller Relieflack aufgetragen worden, innen hat das Buch bedrucktes Vorsatzpapier. Ziel des Projektes war es, Männlichkeit und die verschiedenen Meinungen dazu möglichst verständlich wiedergeben zu können, um so einen Dialog zum Thema anzuregen. KW - Männlichkeit KW - Editorial KW - Typografie KW - Gesellschaftskritik KW - Diskurs Y1 - 2023 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER - TY - THES A1 - Stiphout, Maret van T1 - Entwicklung eines neuen Erscheinungsbildes für das Wallraf-Richartz-Museum und Fondation Carboud N2 - Das Wallraf-Richartz-Museum & Fondation Corboud besitzt eine der wichtigsten europäischen Kunstsammlungen vom Mittelalter bis zum 19. Jahrhundert. Durch das Zusammenspiel von Forschung und Vermittlung der Kunst- und Epochengeschichte trägt das Museum maßgeblich zum Erhalt des kulturellen Erbes und dem Meinungsaustausch über die Vergangenheit, Gegenwart und die Zukunft bei. Im Fokus des neuen Erscheinungsbildes steht die an den kulturellen und historischen Kontext angepasste Szenografie des Museums. Die beeindruckend verzierten Bilderrahmen der gezeigten Kunstepochen werden abstrahiert und durch einen typografischen Rahmen neu interpretiert. Das entwickelte Headline-Prinzip wird durch eine sehr zurückhaltende Gestaltung ergänzt, was der Thematik und den gezeigten Meisterwerken Raum zum Wirken verleiht. KW - Corporatedesign KW - Wallrafmuseum KW - Neugestaltung KW - Mittelalter KW - Barock Y1 - 2023 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER - TY - THES A1 - Transfeld, Janine T1 - Ein Kl-gestütztes Software-Tool : zur Unterstützung der Projektgestaltung der BMW AG N2 - Die Bachelorarbeit beschäftigte sich mit der Integration von künstlicher Intelligenz (KI) in softwarebasierte Lösungen und hatte das Ziel, ein prototypisches Lösungsmodell zu entwickeln. Dabei wurde das User-Experience-Designverfahren angewendet, um eine neue innovative Arbeitsweise zu schaffen, die KI-gestützte Produktentwicklungsprozesse umfasst. KW - Kooperation KW - FH Aachen KW - BMW KW - Künstliche Intelligenz KW - Neue Arbeitsweise Y1 - 2023 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER - TY - THES A1 - Vaut, Ina T1 - Hippocampus N2 - Hippocampus – Eine Publikation über das Erscheinungsbild und Verhaltensweisen von Seepferdchen, ihre Lebensräume, Bedrohungen und die Schutzmaßnahmen. Seepferdchen gehören zu den wenigen Fischarten, die allgemein bekannt sind. In den meisten Fällen werden Seepferdchen einfach als »süß« beschrieben. Doch Seepferdchen haben weit mehr zu bieten als ihr märchenhaftes Aussehen. Diese Publikation setzt sich mit kuriosen Erkenntnissen, aktuellen Forschungsergebnissen und Mythen rund um Seepferdchen auseinander und dient als Einstieg in die Thematik. KW - Editorail Design KW - Publikation KW - Seepferdchen KW - Habitate KW - Spezies Y1 - 2023 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER - TY - JOUR A1 - Kowalewski, Paul A1 - Bragard, Michael A1 - Hüning, Felix A1 - De Doncker, Rik W. T1 - An inexpensive Wiegand-sensor-based rotary encoder without rotating magnets for use in electrical drives JF - IEEE Transactions on Instrumentation and Measurement N2 - This paper introduces an inexpensive Wiegand-sensor-based rotary encoder that avoids rotating magnets and is suitable for electrical-drive applications. So far, Wiegand-sensor-based encoders usually include a magnetic pole wheel with rotating permanent magnets. These encoders combine the disadvantages of an increased magnet demand and a limited maximal speed due to the centripetal force acting on the rotating magnets. The proposed approach reduces the total demand of permanent magnets drastically. Moreover, the rotating part is manufacturable from a single piece of steel, which makes it very robust and cheap. This work presents the theoretical operating principle of the proposed approach and validates its benefits on a hardware prototype. The presented proof-of-concept prototype achieves a mechanical resolution of 4.5 ° by using only 4 permanent magnets, 2Wiegand sensors and a rotating steel gear wheel with 20 teeth. KW - Rotary encoder KW - Wiegand sensor Y1 - 2023 U6 - https://doi.org/10.1109/TIM.2023.3326166 SN - 0018-9456 (Print) SN - 1557-9662 (Online) N1 - Early Access SP - 10 Seiten PB - IEEE ER - TY - CHAP A1 - Heimes, Heiner Hans A1 - Kampker, Achim A1 - Kehrer, Mario A1 - Dünnwald, Simon A1 - Heetfeld, Lennart A1 - Polzenberg, Jens A1 - Budde, Lucas A1 - Keusen, Maximilian A1 - Pandey, Rahul A1 - Röth, Thilo ED - Kampker, Achim ED - Heimes, Heiner Hans T1 - Fahrzeugstruktur T2 - Elektromobilität: Grundlagen einer Fortschrittstechnologie N2 - Um sowohl Treibhausgas-Emissionen zu verringern als auch Kraftstoffressourcen zu schonen, wird zunehmend an einer Transformation konventionell angetriebener Kraftfahrzeuge hin zu elektrifizierten Antriebskonzepten gearbeitet. Basierend auf herkömmlichen Fahrzeugen mit Verbrennungsmotor wurde eine Vielzahl neuer Antriebssysteme mit verschiedenem Elektrifizierungsgrad entwickelt. Mitte der 1990er-Jahre kamen erste Fahrzeuge mit einem Hybridantrieb auf den Markt. Die Kombination aus Verbrennungs- und Elektromotor erlaubt eine Verbrauchsreduktion und Bremsenergierückgewinnung sowie lokal emissionsfreies Fahren. Y1 - 2023 SN - 978-3-662-65811-6 (Print) SN - 978-3-662-65812-3 (Online) U6 - https://doi.org/10.1007/978-3-662-65812-3_5 N1 - Corresponding author: Heiner Hans Heimes SP - 69 EP - 106 PB - Springer Vieweg CY - Berlin ER - TY - CHAP A1 - Heimes, Heiner Hans A1 - Kampker, Achim A1 - Dorn, Benjamin A1 - Kehrer, Mario A1 - Dünnwald, Simon A1 - Badura, Dennis A1 - Terren, Maximilian A1 - Röth, Thilo ED - Kampker, Achim ED - Heimes, Heiner Hans T1 - Produktionsprozesse der Fahrzeugstruktur T2 - Elektromobilität: Grundlagen einer Fortschrittstechnologie Y1 - 2023 SN - 978-3-662-65811-6 (Print) SN - 978-3-662-65812-3 (Online) U6 - https://doi.org/10.1007/978-3-662-65812-3_13 N1 - Corresponding author: Benjamin Dorn SP - 227 EP - 247 PB - Springer Vieweg CY - Berlin ER - TY - CHAP A1 - Kurz, Melanie T1 - Waffen und militärische Ausrüstung in Systemspielzeugwelten T2 - Design für Spiel, Spaß, Spannung: Gestaltung von Artefakten zum spielerischen Handeln / herausgegeben von Melanie Kurz und Thilo Schwer Y1 - 2023 SN - 978-3-89986-396-3 SP - 104 EP - 121 PB - avedition CY - Stuttgart ER - TY - THES A1 - Leiwen, Sophie T1 - Steinreich : Mineralien des Siegerlands N2 - Der Aufbau und die Entstehung unseres Planeten sind untrennbar mit der Bildung von Gesteinen verbunden – diese setzen sich aus verschiedenen Mineralien zusammen. Sie sind in der Natur weit verbreitet und spielen eine entscheidende Rolle in unserem täglichen Leben. Obwohl vielen Menschen der Nutzen von Bodenschätzen bewusst ist, besteht ein geringes Wissen über deren Vorkommen und Relevanz. Für die wirtschaftliche Entwicklung des Siegerlandes beispielsweise waren der Abbau und der Handel mit Mineralien von großer Bedeutung. Insbesondere der langjährige Abbau von Eisenerz legte den Grundstein für die gesamte Metallindustrie der Region. Die Publikation visualisiert eine umfangreiche Sammlung Siegerländer Mineralien und vermittelt ein grundlegendes Verständnis von Mineralien. KW - Mineralien KW - Mineral KW - Siegerland KW - Gesteine KW - Eisenerz Y1 - 2023 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER - TY - CHAP A1 - Alhaskir, Mohamed A1 - Tschesche, Matteo A1 - Linke, Florian A1 - Schriewer, Elisabeth A1 - Weber, Yvonne A1 - Wolking, Stefan A1 - Röhrig, Rainer A1 - Koch, Henner A1 - Kutafina, Ekaterina ED - Röhrig, Rainer ED - Grabe, Niels ED - Haag, Martin ED - Hübner, Ursula ED - Sax, Ulrich ED - Schmidt, Carsten Oliver ED - Sedlmayr, Martin ED - Zapf, Antonia T1 - ECG matching: an approach to synchronize ECG datasets for data quality comparisons T2 - Proceedings of the 68th Annual Meeting of the German Association of Medical Informatics, Biometry, and Epidemiology e.V. (gmds) 2023 N2 - Clinical assessment of newly developed sensors is important for ensuring their validity. Comparing recordings of emerging electrocardiography (ECG) systems to a reference ECG system requires accurate synchronization of data from both devices. Current methods can be inefficient and prone to errors. To address this issue, three algorithms are presented to synchronize two ECG time series from different recording systems: Binned R-peak Correlation, R-R Interval Correlation, and Average R-peak Distance. These algorithms reduce ECG data to their cyclic features, mitigating inefficiencies and minimizing discrepancies between different recording systems. We evaluate the performance of these algorithms using high-quality data and then assess their robustness after manipulating the R-peaks. Our results show that R-R Interval Correlation was the most efficient, whereas the Average R-peak Distance and Binned R-peak Correlation were more robust against noisy data. KW - Electrocardiography KW - Wearable electronic device KW - Sensors comparison KW - Time-series synchronization Y1 - 2023 SN - 978-1-64368-428-4 (Print) SN - 978-1-64368-429-1 (Online) U6 - https://doi.org/10.3233/SHTI230718 N1 - Proceedings of the 68th Annual Meeting of the German Association of Medical Informatics, Biometry, and Epidemiology e.V. (gmds) 2023, 17. - 21.9.23, Heilbronn, Germany Part of the series: Studies in Health Technology and Informatics VL - 307 SP - 225 EP - 232 PB - IOS Press ER - TY - BOOK A1 - Heuermann, Holger T1 - Hochfrequenztechnik. Komponenten und Mess-, Funk-, RFID- sowie Lokalisierungssysteme N2 - Dieses Lehr- und Fachbuch vermittelt anschaulich die Grundlagen der HF-Technik, gibt konkrete Beschreibungen für den Entwurf von linearen Komponenten aus Bauteilen wie auch Leitungen für High-Speed- und HF-Schaltungen. Dem Leser wird vermittelt, wie Bauteile modelliert und Schaltungen synthetisiert und optimiert werden. Mit Hilfe frei verfügbarer Simulationssoftware können GHz-Schaltungen selbst entwickelt werden. Viele Übungsbeispiele ermöglichen die Eigenkontrolle des Wissensstandes. Weiterhin werden komplexe nichtlineare Komponenten wie Hochfrequenzmischer, Oszillatoren und Synthesegeneratoren in ihrer Funktionalität dargestellt. Die neuen Mixed-Mode-Streuparameter sowie deren Leitungs- und Schaltungstechnik für Anwendungen der schnellen Digital- und der modernen HF-Technik sind ausführlich beschrieben. Es wird auf Systeme für folgende Bereiche eingegangen: Streuparametermesstechnik, verschiedene Funktechniken, UHF-RFID und Lokalisierung- und Ortung. Dem Leser wird somit ermöglicht, komplexe GHz-Schaltungen insbesondere mit Halbleiter-, SMD- und LTCC-Schaltungen zu entwickeln. Y1 - 2023 SN - 978-3-658-37825-7 (Print) SN - 978-3-658-37826-4 (eBook) PB - Springer Fachmedien CY - Wiesbaden ET - 4 ER - TY - THES A1 - Scheffel, Zeno Samuel T1 - Identität, Zusammenhalt, Zugehörigkeit : Die Exploration der Gestaltung von Fußballtrikots N2 - Das Fußballtrikot – Arbeitsbekleidung, Identifikationsmerkmal, Distinktionsmerkmal? Was ist das Fußballtrikot, was sind seine identitätsstiftenden Merkmale und welche Gestaltungsparameter prägen sein heutiges Aussehen? In dieser Publikation wird die Geschichte des Trikots ebenso wie die äußeren Einflüsse auf sein heutiges Erscheinungsbild dokumentiert und analysiert. Die Publikation definiert die verschiedenen Gestaltungsparameter, erläutert diese und ordnet sie ein. Ebenso wird ein Einblick in den kreativen Gestaltungsprozess von Fußballtrikots gewährt. Das Ziel dieser Publikation besteht darin, das Erscheinungsbild von Trikots zu verstehen und eine kritische Reflexion darüber zu ermöglichen, wie das Fußballtrikot individuell definiert wird. KW - Fußballtrikot KW - Trikot KW - Arbeitsbekleidung KW - Identifikation KW - Distinktion KW - Kommunikationsdesign Y1 - 2023 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER - TY - THES A1 - Schlepütz, Nico T1 - News Flow : Nachrichten- und Informationsprozesse im digitalen Wandel N2 - "News Flow" Nachrichten- und Informationsprozesse im digitalen Wandel. In der digitalen Welt sind wir von Informationen aus unterschiedlichen Medien umgeben. Die ständige Verfügbarkeit führt zu Überforderung und Orientierungslosigkeit. Junge Menschen bevorzugen Streaming und Social Media gegenüber traditionellen Nachrichten. Angesichts globaler Krisen und Desinformation sind innovative Lösungen wichtig, um den Informationsfluss zu verbessern. "News Flow" ist eine digitale Anwendung für Alternativen des Nachrichtenkonsums. Sie berücksichtigt individuelle Bedürfnisse und nutzt moderne Technologien. Durch die visuelle Vermittlung wird das Interesse an Nachrichten gesteigert und junge Zielgruppen angesprochen. Diese Arbeit stellt sich den Herausforderungen des digitalen Wandels im Nachrichtenbereich und eröffnet eine neue Perspektive auf den Nachrichtenkonsum. KW - Informationsfluss KW - Good News Fokus KW - UX Design KW - UI Design KW - Alternative Konsumoption Y1 - 2023 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER - TY - THES A1 - Schmidt, Lucie T1 - „Keine Schmerzen in der Regel“ : Aufklärungskampagne zur Früherkennung der Krankheit Endometriose N2 - Jede zehnte Frau hat Endometriose. Hierbei entstehen Zysten und Entzündungen, welche sich beispielsweise an den Eierstöcken ansiedeln können. Wie kann es also sein, dass so viele noch nie was von dieser Erkrankung gehört haben? Mit der online Aufklärungskampagne „ Keine Schmerzen in der Regel“ soll sich das ändern. In vielen Fällen werden Beschwerden der Endometriose fälschlicherweise als normale Menstruationsbeschwerden abgetan. Die Differenzierung zwischen normal und nicht normal misslingt. Die Aufmerksamkeit von Mädchen und Frauen, die sich in den nicht normalen Aspekten wiederfinden, soll erregt werden. Dafür werden vier Symptome visualisiert und gegenübergestellt. Zusätzlich bietet ein Schnellcheck weitere Informationen. Diese Kampagne soll dem Problem der Unbekanntheit von Endometriose entgegenwirken und ein gesellschaftliches Bewusstsein für sie schaffen. KW - Aufklärungskampagne KW - Endometriose KW - Krankheit KW - Kommunikationsdesign Y1 - 2023 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER - TY - BOOK A1 - Heuermann, Holger T1 - Mikrowellentechnik : Feldsimulation, nichtlineare Schaltungstechnik, Komponenten und Subsysteme, Plasmatechnik, Antennen und Ausbreitung N2 - Das Lehrbuch behandelt alle Aspekte, die den aktuellen Stand der GHz-Technik betreffen. Das Buch behandelt die verschiedenen numerischen Feldsimulationsverfahren. Mit vielen modernen Themen. KW - Elektrotechnik KW - Hochfrequenztechnik KW - Feldsimulation KW - Plasmatechnik KW - Antennen Y1 - 2023 SN - 978-3-658-41286-9 U6 - https://doi.org/10.1007/978-3-658-41287-6 PB - Springer Vieweg CY - Wiesbaden ET - 2. Auflage ER - TY - CHAP A1 - Eichenbaum, Julian A1 - Nikolovski, Gjorgji A1 - Mülhens, Leon A1 - Reke, Michael A1 - Ferrein, Alexander A1 - Scholl, Ingrid T1 - Towards a lifelong mapping approach using Lanelet 2 for autonomous open-pit mine operations T2 - 2023 IEEE 19th International Conference on Automation Science and Engineering (CASE) N2 - Autonomous agents require rich environment models for fulfilling their missions. High-definition maps are a well-established map format which allows for representing semantic information besides the usual geometric information of the environment. These are, for instance, road shapes, road markings, traffic signs or barriers. The geometric resolution of HD maps can be as precise as of centimetre level. In this paper, we report on our approach of using HD maps as a map representation for autonomous load-haul-dump vehicles in open-pit mining operations. As the mine undergoes constant change, we also need to constantly update the map. Therefore, we follow a lifelong mapping approach for updating the HD maps based on camera-based object detection and GPS data. We show our mapping algorithm based on the Lanelet 2 map format and show our integration with the navigation stack of the Robot Operating System. We present experimental results on our lifelong mapping approach from a real open-pit mine. Y1 - 2023 SN - 979-8-3503-2069-5 (Online) SN - 979-8-3503-2070-1 (Print) U6 - https://doi.org/10.1109/CASE56687.2023.10260526 N1 - 19th International Conference on Automation Science and Engineering (CASE), 26-30 August 2023, Auckland, New Zealand. PB - IEEE ER - TY - CHAP A1 - Tischbein, Franziska A1 - Kean, Kilian A1 - Vertgewall, Chris Martin A1 - Ulbig, Andreas A1 - Altherr, Lena T1 - Determination of the topology of low-voltage distribution grids using cluster methods T2 - 27th International Conference on Electricity Distribution (CIRED 2023) N2 - Due to the decarbonization of the energy sector, the electric distribution grids are undergoing a major transformation, which is expected to increase the load on the operating resources due to new electrical loads and distributed energy resources. Therefore, grid operators need to gradually move to active grid management in order to ensure safe and reliable grid operation. However, this requires knowledge of key grid variables, such as node voltages, which is why the mass integration of measurement technology (smart meters) is necessary. Another problem is the fact that a large part of the topology of the distribution grids is not sufficiently digitized and models are partly faulty, which means that active grid operation management today has to be carried out largely blindly. It is therefore part of current research to develop methods for determining unknown grid topologies based on measurement data. In this paper, different clustering algorithms are presented and their performance of topology detection of low voltage grids is compared. Furthermore, the influence of measurement uncertainties is investigated in the form of a sensitivity analysis. Y1 - 2023 SN - 978-1-83953-855-1 U6 - https://doi.org/10.1049/icp.2023.0478 N1 - 27th International Conference on Electricity Distribution (CIRED 2023), 12-15 June 2023, Rome, Italy. SP - 1 EP - 5 PB - IEEE ER - TY - CHAP A1 - Freyer, Nils A1 - Kempt, Hendrik ED - Bhakuni, Himani ED - Miotto, Lucas T1 - AI-DSS in healthcare and their power over health-insecure collectives T2 - Justice in global health N2 - AI-based systems are nearing ubiquity not only in everyday low-stakes activities but also in medical procedures. To protect patients and physicians alike, explainability requirements have been proposed for the operation of AI-based decision support systems (AI-DSS), which adds hurdles to the productive use of AI in clinical contexts. This raises two questions: Who decides these requirements? And how should access to AI-DSS be provided to communities that reject these standards (particularly when such communities are expert-scarce)? This chapter investigates a dilemma that emerges from the implementation of global AI governance. While rejecting global AI governance limits the ability to help communities in need, global AI governance risks undermining and subjecting health-insecure communities to the force of the neo-colonial world order. For this, this chapter first surveys the current landscape of AI governance and introduces the approach of relational egalitarianism as key to (global health) justice. To discuss the two horns of the referred dilemma, the core power imbalances faced by health-insecure collectives (HICs) are examined. The chapter argues that only strong demands of a dual strategy towards health-secure collectives can both remedy the immediate needs of HICs and enable them to become healthcare independent. Y1 - 2023 SN - 9781003399933 U6 - https://doi.org/10.4324/9781003399933-4 SP - 38 EP - 55 PB - Routledge CY - London ER - TY - THES A1 - Schmitz, Marvin T1 - Eishockey Uni-Cup der RWTH Aachen : Produktion einer Sportübertragung N2 - Der Uni-Cup ist ein Amateur Eishockey Turnier der RWTH Aachen. Es treten Studierende und Professor:innen gegeneinander an. Ausgetragen wurde das Turnier vor etwa 2.500 Zuschauern in der 100,5 Arena am Tivoli. Um das Event einer breiteren Masse zugänglich zu machen, wurde dort im Rahmen der Bachelorarbeit erstmals eine Live Übertragung produziert. Das Ziel dabei war es, eine möglichst professionelle und unterhaltsame Show zu kreieren. KW - Livestream KW - Eishockey KW - Sport KW - RWTH Aachen KW - Regie Y1 - 2023 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER - TY - BOOK A1 - Janser, Frank A1 - Havermann, Marc A1 - Hoeveler, Bastian A1 - Hertz, Cyril A1 - Bergmann, Ole T1 - Strömungslehre und Aerodynamik : inkompressible Profile und Tragflügelaerodynamik, Band 2 N2 - Das vorliegende Buch dient als Grundlage für die Bachelor- und Master-Ausbildung von Studierenden im Fachgebiet Strömungslehre und Aerodynamik. Im hier behandelten Teilbereich der inkompressiblen Profile und Tragflügelaerodynamik werden schwerpunktmäßig die folgenden Themen besprochen: - Profilaerodynamik - Tragflügelaerodynamik - Flugzeugpolare - Methoden zur Flugbereichserweiterung - Schwebeschub und Schwebeleistung - Propellerblattaerodynamik - Numerische Methoden zur Tragflügelberechnung Y1 - 2023 SN - 978-3-8107-0261-6 PB - Mainz CY - Aachen ET - 4. Auflage ER - TY - THES A1 - Farjam, Ina T1 - Farfilia : experimenteller Tanzfilm über eine Vater-Tochter-Beziehung N2 - Der experimentelle Tanzfilm „Farfilia“ behandelt die Beziehung einer Tochter zu ihrem Vater. Beide Parteien funktionieren sehr unterschiedlich, denken, kommunizieren und leben in völlig verschiedenen Welten. Es findet ein Konflikt zwischen den Generationen statt, zwischen zwei sehr gegensätzlichen Prägungen und Charakteren. Die zwei Welten unterscheiden sich nicht nur in ihrer Visualität, sondern durch die in ihr lebenden und handelnden zwei Hauptprotagonist*innen, welches bildgestalterisch durch ein Zusammenspiel von Cinematographie, Choreographie und Setting ausgearbeitet und dargestellt wird. Durch die gemeinsame Wirkung vieler unterschiedlicher Gestaltungsmittel soll eine Geschichte erzählt werden, in der sich beide Welten aufeinander zu bewegen und am Ende Elemente der jeweils anderen Welt in sich aufnehmen und für die eigene Empfindung in der jeweiligen Umgebung adaptieren. KW - Experimentalfilm KW - Vater KW - Tochter KW - Tanz KW - Abstrakt Y1 - 2023 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER -