TY  - JOUR
A1  - Kirchner, Patrick
A1  - Oberländer, Jan
A1  - Friedrich, Peter
A1  - Berger, Jörg
A1  - Rysstad, Gunnar
A1  - Schöning, Michael Josef
A1  - Keusgen, Michael
T1  - Realisation of a calorimetric gas sensor on polyimide foil for applications in aseptic food industry
JF  - Sensors and Actuators B: Chemical
N2  - A calorimetric gas sensor is presented for the monitoring of vapour-phase H2O2 at elevated temperature during sterilisation processes in aseptic food industry. The sensor was built up on a flexible polyimide foil (thickness: 25 μm) that has been chosen due to its thermal stability and low thermal conductivity. The sensor set-up consists of two temperature-sensitive platinum thin-film resistances passivated by a layer of SU-8 photo resist and catalytically activated by manganese(IV) oxide. Instead of an active heating structure, the calorimetric sensor utilises the elevated temperature of the evaporated H2O2 aerosol. In an experimental test rig, the sensor has shown a sensitivity of 4.78 °C/(%, v/v) in a H2O2 concentration range of 0%, v/v to 8%, v/v. Furthermore, the sensor possesses the same, unchanged sensor signal even at varied medium temperatures between 210 °C and 270 °C of the gas stream. At flow rates of the gas stream from 8 m3/h to 12 m3/h, the sensor has shown only a slightly reduced sensitivity at a low flow rate of 8 m3/h. The sensor characterisation demonstrates the suitability of the calorimetric gas sensor for monitoring the efficiency of industrial sterilisation processes.
KW  - Sterilisation process
KW  - Hydrogen peroxide
KW  - Polyimide
KW  - Calorimetric gas sensor
Y1  - 2012
U6  - http://dx.doi.org/10.1016/j.snb.2011.01.032
SN  - 0925-4005
N1  - Part of special issue "Eurosensors XXIV, 2010"
VL  - 170
SP  - 60
EP  - 66
PB  - Elsevier
CY  - Amsterdam
ER  - 
TY  - JOUR
A1  - Kirchner, Patrick
A1  - Li, Bin
A1  - Spelthahn, Heiko
A1  - Henkel, Hartmut
A1  - Schneider, Andreas
A1  - Friedrich, Peter
A1  - Kolstad, Jens
A1  - Keusgen, Michael
A1  - Schöning, Michael Josef
T1  - Thin-film calorimetric H2O2 gas sensor for the validation of germicidal effectivity in aseptic filling processes
JF  - Sensors and Actuators B: Chemical. 154 (2011), H. 2
Y1  - 2011
SN  - 1873-3077
N1  - EUROSENSORS XXIII
SP  - 257
EP  - 263
PB  - Elsevier
CY  - Amsterdam
ER  - 
TY  - JOUR
A1  - Kirchner, Patrick
A1  - Oberländer, Jan
A1  - Friedrich, Peter
A1  - Berger, Jörg
A1  - Suso, Henri-Pierre
A1  - Kupyna, Andriy
A1  - Keusgen, Michael
A1  - Schöning, Michael Josef
T1  - Optimisation and fabrication of a calorimetric gas sensor built up on a polyimide substrate for H2O2 monitoring
JF  - Physica status solidi (a) : applications and material science. 208 (2011), H. 6
Y1  - 2011
SN  - 1862-6319
SP  - 1235
EP  - 1240
PB  - Wiley
CY  - Weinheim
ER  - 
TY  - JOUR
A1  - Schöning, Michael Josef
A1  - Kirchner, Patrick
A1  - Ng, Yue Ann
A1  - Spelthahn, Heiko
A1  - Schneider, Andreas
A1  - Henkel, Hartmut
A1  - Friedrich, Peter
A1  - Kolstad, Jens
A1  - Berger, Jörg
A1  - Keusgen, Michael
T1  - Gas sensor investigation based on a catalytically activated thin-film thermopile for H2O2 detection
JF  - Physica Status Solidi (A). 207 (2010), H. 4
Y1  - 2010
SN  - 1862-6300
N1  - Special Issue: Engineering of Functional Interfaces EnFI 2009
SP  - 787
EP  - 792
ER  - 
TY  - JOUR
A1  - Kirchner, Patrick
A1  - Oberländer, Jan
A1  - Friedrich, Peter
A1  - Rysstad, G.
A1  - Berger, J.
A1  - Keusgen, M.
A1  - Schöning, Michael Josef
T1  - Realization of a calorimetric gas sensor on polyimide foil for applications in aseptic food industry
JF  - Procedia Engineering. 5 (2010)
Y1  - 2010
SN  - 1877-7058
N1  - Eurosensor XXIV Conference
SP  - 264
EP  - 267
ER  - 
TY  - GEN
A1  - Achten, Richard
A1  - Bauer, Andreas
A1  - Bertram, Walter
A1  - Cremer, Markus
A1  - Daemen, Jos
A1  - Dehnhardt, Markus
A1  - Fleischer, Manfred
A1  - Kirchner, Peter
A1  - Leyendecker, Marco
A1  - Pietrzyk, Uwe
A1  - Schmitz, Jakob
A1  - Ziemons, Karl
A1  - Zilles, Karl
T1  - Vorrichtung zum Halten eines lebenden Objektes bei physiologischen Messungen
N2  - Die vorliegende Erfindung betrifft eine Vorrichtung zum Halten eines lebenden Objektes bei physiologischen Messungen mit einem Basiselement und Mitteln zum Arretieren des lebenden Objektes, die atraumatische Ohrenhalter sowie ein Mundstück aufweisen, das mit einer Aussparung für die Zähne des Lebewesens versehen ist, mit einem Masseanteil von wenigstens 95% an glasfaserverstärktem Kunststoff.
Y1  - 2005
N1  - Patent Anmelder : Forschungszentrum Jülich GmbH
SP  - 1
EP  - 17
ER  -