TY  - JOUR
A1  - Butenweg, Christoph
A1  - Marinković, Marko
A1  - Kubalski, Thomas
A1  - Fehling, Ekkehard
A1  - Pfetzing, Thomas
A1  - Meyer, Udo
ED  - Voss, Michael
T1  - Auslegung von Stahlbetonrahmentragwerken mit Ausfachungen aus Ziegelmauerwerk (Teil 1)
T1  - Design of reinforced concrete enclosures infilled with clay block masonry (Part 1)
JF  - Ziegelindustrie international : ZI = Brick and tile industry international
N2  - Im Rahmen des europäischen Verbundprojekts INSYSME wurden von den deutschen Partnern die Systeme IMES und INODIS zur Verbesserung des seismischen Verhaltens von ausgefachten Stahlbetonrahmen entwickelt. Ziel beider Systeme ist es, Stahlbetonrahmen und Ausfachung zu entkoppeln, anstatt die Tragfähigkeit durch aufwendige und kostspielige zusätzliche Bewehrungseinlagen zu erhöhen. Erste Ergebnisse des Systems IMES für Belastungen in und senkrecht zu der Wandebene werden vorgestellt.
N2  - Within the scope of the joint European project INSYSME, the German partners developed two systems - IMES and INODIS - for improving the seismic behaviour of masonry infilled reinforced concrete frames. The purpose of both systems is to decouple frame and infill instead of working to improve their load-bearing capacity by means of elaborate, expensive, supplementary reinforcing elements. Initial findings for the IMES system with regard to the loads acting in-plane and perpendicular to the wall plane (out-of-plane) are presented.
Y1  - 2018
SN  - 0341-0552
IS  - 4
SP  - 30
EP  - 39
PB  - Bauverlag BV GmbH
CY  - Gütersloh
ER  - 
TY  - CHAP
A1  - Butenweg, Christoph
A1  - Roeser, W.
T1  - Auslegung von Bauwerken gegen Erdbeben - Rechenbeispiele
T2  - Stahlbetonbau aktuell 2016 : Praxishandbuch / herausgegeben von: Prof. Dr.-Ing. Josef Hegger, Prof. Dr.-Ing. habil. Peter Mark
Y1  - 2016
SN  - 978-3-410-25202-3 (Print) ; 978-3-410-25203-0 (E-Book)
PB  - Beuth Verlag GmbH
CY  - Berlin ; Wien ; Zürich
ER  - 
TY  - CHAP
A1  - Kubalski, T.
A1  - Butenweg, Christoph
T1  - Ausfachungsmauerwerk unter kombinierter seismischer Beanspruchung
T2  - Erdbeben und bestehende Bauten : 14. D-A-C-H Tagung 20.08. - 21.08.2015, ETH Zürich. (Dokumentation / SIA ; D 0255)
Y1  - 2015
SN  - 978-3-03732-060-0
SP  - 117
EP  - 122
PB  - SGEB
CY  - Zürich
ER  - 
TY  - JOUR
A1  - Marinkovic, Marko
A1  - Butenweg, Christoph
T1  - Ausfachungen aus Ziegelmauerwerk in Stahlbetonrahmentragwerken unter Erdbebenbeanspruchung
JF  - Mauerwerk
N2  - Stahlbetonrahmentragwerke mit Ausfachungen aus Mauerwerk weisen nach Erdbeben häufig schwere Schäden auf. Gründe hierfür sind die Beanspruchungen der Ausfachungswände durch die aufgezwungenen Rahmenverformungen in Wandebene und die gleichzeitig auftretenden Trägheitskräfte senkrecht zur Wandebene in Kombination mit der konstruktiven Ausführung des Ausfachungsmauerwerks. Die Ausfachung wird in der Regel knirsch gegen die Rahmenstützen gemauert, wobei der Verschluss der oberen Fuge mit Mörtel oder Montageschaum erfolgt. Dadurch kommt es im Erdbebenfall zu lokalen Interaktionen zwischen Ausfachung und Rahmen, die in der Folge zu einem Versagen einzelner Ausfachungswände oder zu einem sukzessiven Versagen des Gesamtgebäudes führen können. Die beobachteten Schäden waren die Motivation dafür, in dem europäischen Forschungsprojekt INSYSME für Stahlbetonrahmentragwerke mit Ausfachungen aus hochwärmedämmenden Ziegelmauerwerk innovative Lösungen zur Verbesserung des seismischen Verhaltens zu entwickeln. Der vorliegende Beitrag stellt die im Rahmen des Projekts von den deutschen Projektpartnern (Universität Kassel, SDA-engineering GmbH) entwickelten Lösungen vor und vergleicht deren seismisches Verhalten mit der traditionellen Ausführung der Ausfachungswände. Grundlage für den Vergleich sind statisch-zyklische Wandversuche und Simulationen auf Wandebene. Aus den Ergebnissen werden Empfehlungen für die erdbebensichere Auslegung von Stahlbetonrahmentragwerken mit Ausfachungen aus Ziegelmauerwerk abgeleitet.
Y1  - 2020
U6  - https://doi.org/10.1002/dama.202000011
SN  - 1437-1022
VL  - 24
IS  - 4
SP  - 194
EP  - 205
PB  - Wiley
CY  - Weinheim
ER  - 
TY  - CHAP
A1  - Butenweg, Christoph
A1  - Kubalski, Thomas
A1  - Marinkovic, Marko
A1  - Pfetzing, Thomas
A1  - Ismail, Mohammed
A1  - Fehling, Ekkehard
T1  - Ausfachungen aus Ziegelmauerwerk
T2  - Mauerwerk-Kalender 2016: Baustoffe, Sanierung, Eurocode-Praxis
Y1  - 2016
SN  - 978-3-433-03131-5
PB  - Ernst & Sohn
CY  - Berlin
ER  - 
TY  - JOUR
A1  - Brüssermann, Klaus
T1  - Ausbreitungsrechnungen aus ingenieurtechnischer Sicht
JF  - Meeting of Umweltbundesamt Working Group for Diffusion Calculation, Berlin (Germany, F.R.), 10 May 1984
Y1  - 1984
N1  - Heft 21/85
SP  - 1
EP  - 11
ER  - 
TY  - CHAP
A1  - Stangel-Meseke, Martina
A1  - Hahn, Pia
A1  - Steuer-Dankert, Linda
T1  - Ausblick: Der individualitätsbezogene Diversity Management-Ansatz als Antwort auf Individualisierung
T2  - Diversity Management und Individualisierung
N2  - Der Megatrend Individualisierung fordert von Unternehmen, ihre Strategien und Prozessabläufe bei zunehmender Globalisierung grundlegend zu überdenken. Während Strategien und Prozessabläufe im Unternehmen Standards unterliegen, entwickelt sich unsere Gesellschaft immer stärker zu einem individuumszentrierten System, in dem es gilt, Werte und Lebensstile der Individuen zu berücksichtigen und derart wertzuschätzen, dass Mitarbeitende motiviert und mit hoher Bindung an das Unternehmen die anstehenden Leistungen für das Unternehmen erbringen. Im Konzept DiM sind Standardisierung und Individualisierung keine gegensätzlichen Aspekte, da bei DiM neben der Betrachtung des betriebswirtschaftlichen Nutzens dieses Konzepts für Unternehmen die Wertschätzung des Individuums als genuines Merkmal betont wird.
Y1  - 2015
SN  - 978-3-658-07485-2
SP  - 23
EP  - 24
PB  - Springer Gabler
CY  - Wiesbaden
ER  - 
TY  - JOUR
A1  - Buck, H.
A1  - Schwarzer, Klemens
A1  - Meliß, Michael
A1  - Faber, Christian
T1  - Aus- und Weiterbildung am Solar-Institut Jülich
JF  - Energiewirtschaftliche Tagesfragen. 44 (1994), H. 9
Y1  - 1994
SN  - 0720-6240
SP  - 65
EP  - 68
ER  - 
TY  - JOUR
A1  - Buck, H.
A1  - Faber, Christian
A1  - Meliß, Michael
A1  - Schwarzer, Klemens
T1  - Aus- und Weiterbildung am Solar-Institut Jülich
JF  - Energie für die Zukunft : 28. Juni bis 1. Juli 1994 ; [Tagungsbericht 2] / 9. Internationales Sonnenforum '94. [Hrsg. Deutsche Gesellschaft für Sonnenenergie e.V. - DGS. Red. A. Hohmann ; H. H. Hohmann].  - (Internationales Sonnenforum ; 9,2)
Y1  - 1995
N1  - Internationales Sonnenforum <9, 1994, Stuttgart> ; Deutsche Gesellschaft für Sonnenenergie
SP  - 1779
EP  - 1785
PB  - DGS-Sonnenenergie
CY  - München
ER  - 
TY  - CHAP
A1  - Dören, Horst-Peter
A1  - Wernicke, K.
T1  - Auftragen von verschleißfesten stranggegossenen Hartlegierungen auf Kobaltbasis durch das WIG- und Gasschweißen
T2  - Schweißen und Schneiden '83 = Welding and Cutting '83. Vorträge der Großen Schweißtechnischen Tagung in Aachen vom 28. bis 30. September 1983. Veranst.: Deutscher Verband für Schweißtechnik (DVS). DVS-Berichte. 83
Y1  - 1983
SN  - 3-87155-388-3
SP  - 109
EP  - 113
PB  - Dt. Verl. für Schweißtechnik
CY  - Düsseldorf
ER  - 
TY  - CHAP
A1  - Borchert, Jörg
ED  - Zenke, Ines
T1  - Aufbau von Handelseinheiten
T2  - Energiehandel in Europa
Y1  - 2012
SN  - 978-3-406-63237-2
SP  - 467
EP  - 479
PB  - Beck
CY  - München
ET  - 3. Aufl.
ER  - 
TY  - JOUR
A1  - Thielemann, Frank
A1  - Bock, Jürgen
T1  - Aufbau und Management deutsch-russischer Joint-ventures. Bock Jürgen; Thielemann, Frank
JF  - Mit Innovation vom Plan zum Markt
Y1  - 1993
SP  - 111
EP  - 135
CY  - Bochum
ER  - 
TY  - BOOK
A1  - Rateike, Franz-Matthias
A1  - Werner, Linus
A1  - Wunderer, Bernd
T1  - Aufbau und Entwicklung frequenzveränderlicher Hochdruck-Gaslaser für photochemische Anwendungen / Matthias Rateike ; Linus Werner ; Bernd Wunderer.
Y1  - 1980
N1  - Forschungsbericht / Bundesministerium fuer Forschung und Technologie : T ; 80,107
PB  - Fachinformationszentrum Energie, Physik, Mathematik
CY  - Eggenstein-Leopoldshafen
ER  - 
TY  - BOOK
A1  - Hardt, Arno
A1  - Müller, Gerhard
A1  - Berg, G. P.
A1  - Kelleter, H.-J.
T1  - Aufbau eines Plastikszintillationszählers für den Magnetspektrographen "BIG KARL" am Jülicher Zyklotron "JULIC".  Müller, Gerhard; Berg , G. P.; Hardt, A.; Kelleter, H.-J.; Martin, S.-A.; Meissburger, J.
Y1  - 1980
N1  - Spezielle Berichte der Kernforschungsanlage Jülich  ; Nr. 0084
PB  - Kernforschungsanlage Jülich
CY  - Jülich
ER  - 
TY  - JOUR
A1  - Förster, Arnold
A1  - Rosenauer, A.
A1  - Remmele, T.
T1  - Atomic scale strain measurements by the digital analysis of transmission electron microscopic lattice images / A. Rosenauer ; T. Remmele ; D. Gerthsen ... A. Förster
JF  - Optik : international journal for light and electron optics. 105 (1997), H. 3
Y1  - 1997
SN  - 0030-4026
SP  - 99
EP  - 107
ER  - 
TY  - JOUR
A1  - Förster, Arnold
A1  - Rosenauer, A.
A1  - Oberst, W.
A1  - Gerthsen, D.
T1  - Atomic scale analysis of the indium distribution in InGaAs/GaAs (001) heterostructures: segregation, lateral indium redistribution and the effect of growth interruptions. Rosenauer, A. ; Oberst, W. ; Gerthsen, D. ; Förster, A.
JF  - Thin Solid Films. 357 (1999)
Y1  - 1999
SN  - 0040-6090
SP  - 18
EP  - 21
ER  - 
TY  - JOUR
A1  - Lück, Reinhard
A1  - Gerling, Ulrich
A1  - Predel, Bruno
T1  - Assoziation in Mehrstoffsystemen
JF  - Zeitschrift für Metallkunde : international journal of materials research and advanced techniques. Bd. 77, H. 10
Y1  - 1986
SN  - 0044-3093 ; 0179-4841
SP  - 667
EP  - 672
ER  - 
TY  - JOUR
A1  - Gerling, Ulrich
A1  - Predel, Bruno
T1  - Assoziation in flüssigen Gold-Zink-Legierungen und die Zuverlässigkeit der Modellparameter
JF  - Zeitschrift für Metallkunde : international journal of materials research and advanced techniques. Bd. 75, H. 8
Y1  - 1984
SN  - 0044-3093 ; 0179-4841
SP  - 592
EP  - 598
ER  - 
TY  - JOUR
A1  - Gerling, Ulrich
A1  - Lück, Reinhard
A1  - Predel, Bruno
T1  - Assoziation in flüssigen Germanium-Zink-Legierungen
JF  - Zeitschrift für Metallkunde : international journal of materials research and advanced techniques. Bd. 77, H. 6
Y1  - 1986
SN  - 0044-3093 ; 0179-4841
SP  - 489
EP  - 496
ER  - 
TY  - JOUR
A1  - Gerling, Ulrich
A1  - Lück, Reinhard
A1  - Predel, Bruno
T1  - Assoziation in flüssigen Antimon-Zink-Legierungen und die Berücksichtigung der Größenverhältnisse der Teilchen in der Schmelze
JF  - Zeitschrift für Metallkunde : international journal of materials research and advanced techniques. Bd. 77, H. 2
Y1  - 1986
SN  - 0044-3093 ; 0179-4841
SP  - 80
EP  - 86
ER  - 
TY  - GEN
A1  - Frauenrath, Tobias
A1  - de Geyer d'Orth, Thibaut
A1  - Niendorf, Thoralf
T1  - Assessment of Accuracy & Reproducibility of ECG, Pulse Oximetry & Phonocardiogram Gating of Cardiac MRI at 7T
T2  - 2011 ISMRM Annual Meeting Proceedings
N2  - At (ultra)high magnetic fields the artifact sensitivity of ECG recordings increases. This bears the risk of R-wave mis-registration which has been consistently reported for ECG triggered CMR at 7.0T. Realizing the constraints of conventional ECG, acoustic cardiac triggering (ACT) has been proposed. The clinical ACT has not been carefully examined yet. For this reason, this work scrutinizes the suitability, accuracy and reproducibility of ACT for CMR at 7.0T. For this purpose, the trigger reliability and trigger detection variance are examined together with an qualitative and quantitative assessment of image quality of the heart at 7.0T.
Y1  - 2011
SN  - 1545-4428
N1  - ISMRM 19th Annual Meeting & Exhibition, 7-13 May 2011, Montreal, Quebec, Canada
ER  - 
TY  - JOUR
A1  - Förster, Arnold
A1  - Schäfer, B.-J.
A1  - Londschien, M.
T1  - Arsenic passivation of MOMBE grown GaAs surfaces / B. -J. Schäfer ;  A. Förster ; M. Londschien ...
JF  - Surface Science. 204 (1988), H. 3
Y1  - 1988
SN  - 0039-6028
N1  - ISSN der E-Ausg.: 0039-6028
SP  - 485
EP  - 490
ER  - 
TY  - JOUR
A1  - Förster, Arnold
A1  - Resch, U.
A1  - Essera, N.
A1  - Raptis, Y. S.
T1  - Arsenic passivation of MBE grown GaAs(100): structural and electronic properties of the decapped surfaces / U. Resch ;  N. Essera ; Y. S. Raptis ... A. Förster ...
JF  - Surface Science. 269-270 (1992)
Y1  - 1992
SN  - 0039-6028
N1  - ISSN der E-Ausg.: 0039-6028
SP  - 797
EP  - 803
ER  - 
TY  - CHAP
A1  - Hellmanns, Mark
A1  - Fischer, F.
A1  - Dilger, K.
A1  - Wittor, B.
A1  - Hildebrand, J.
A1  - Werner, F.
T1  - Applikation und Einsatz von faserverstärkten Klebstoffen im Bauwesen abgeschlossenes IGF-Projekt Nr. 16956 B (DVS 08.072, Laufzeit 01.02.2011 - 31.01.2013)
T2  - Tagungsband / 14. Kolloquium Gemeinsame Forschung in der Klebtechnik : 18. und 19. Februar 2014, DECHEMA-Haus, Frankfurt am Main
Y1  - 2014
SP  - 26
EP  - 27
ER  - 
TY  - RPRT
A1  - Dilger, Klaus
A1  - Fischer, Fabian
A1  - Hellmanns, Mark
A1  - Werner, Frank
A1  - Wittor, Björn
T1  - Applikation und Einsatz von faserverstärkten Klebstoffen im Bauwesen (FibrAdh) : Schlussbericht : gefördertes Vorhaben 16.956 B / DVS-Nr. 08.072
Y1  - 2013
ER  - 
TY  - CHAP
A1  - Hellmanns, Mark
A1  - Fischer, F.
A1  - Dilger, Klaus
T1  - Applikation und Einsatz von faserverstärkten Klebstoffen im Bauwesen
T2  - Tagungsband / 13. Kolloquium Gemeinsame Forschung in der Klebtechnik : 26. und 27. Februar 2013, Frankfurt am Main
Y1  - 2013
SP  - 61
EP  - 62
PB  - DECHEMA
CY  - Frankfurt a.M.
ER  - 
TY  - JOUR
A1  - Pieper, Martin
A1  - Klein, Peter
T1  - Application of simple, periodic homogenization techniques to non-linear heat conduction problems in non-periodic, porous media
JF  - Heat mass transfer
N2  - Often, detailed simulations of heat conduction in complicated, porous media have large runtimes. Then homogenization is a powerful tool to speed up the calculations by preserving accurate solutions at the same time. Unfortunately real structures are generally non-periodic, which requires unpractical, complicated homogenization techniques. We demonstrate in this paper, that the application of simple, periodic techniques to realistic media, that are just close to periodic, gives accurate, approximative solutions. In order to obtain effective parameters for the homogenized heat equation, we have to solve a so called “cell problem”. In contrast to periodic structures it is not trivial to determine a suitable unit cell, which represents a non-periodic media. To overcome this problem, we give a rule of thumb on how to choose a good cell. Finally we demonstrate the efficiency of our method for virtually generated foams as well as real foams and compare these results to periodic structures.
Y1  - 2012
U6  - https://doi.org/10.1007/s00231-011-0879-4
SN  - 0947-7411
VL  - 48
IS  - 2
SP  - 291
EP  - 300
PB  - Springer
CY  - Berlin
ER  - 
TY  - JOUR
A1  - Helsper, Christoph
A1  - Nießner, R.
A1  - Rönicke, G.
T1  - Application of a Multistep Condensation Nuclei Counter as a Detector for Particle Surface Composition / Nießner, R.; Helsper, C.; Rönicke, G.
JF  - Aerosols : science, technology, and industr. applications of airborne particles ; proceedings of the 1. Internat. Aerosol Conference held Sept. 17-21, 1984, Minneapolis, Minn., U.S.A / ed.: Benjamin Y. H. Liu
Y1  - 1984
SN  - 0444009477
N1  - International Aerosol Conference ; (1, 1984, Minneapolis, Minn.)
SP  - 63
EP  - 66
PB  - Elsevier
CY  - New York [u.a.]
ER  - 
TY  - JOUR
A1  - Helsper, Christoph
A1  - Nießner, R.
T1  - Application of a Multistep Condensation Nuclei Counter as a Detector for Particle Surface Composition / Nießner, R. ; Helsper, C.
JF  - Journal of Aerosol Science. 16 (1985), H. 3
Y1  - 1985
SN  - 0021-8502
SP  - 201
EP  - 209
ER  - 
TY  - CHAP
A1  - Kruska, Martin
A1  - Kuperjans, Isabel
T1  - Análisis Thermodinámicos : [Capítulo 3.3]
T2  - Uso racional de energía : eficiencia energética y energías renovables. - (Manual para consultores y expertos)
Y1  - 1999
SP  - 3.3-1
EP  - 3.3-15
PB  - Ministerio de Energía y Minas
CY  - Lima
ER  - 
TY  - BOOK
A1  - Dören, Horst-Peter
T1  - Anwendung von AlN- bzw. AlN-Al2O3-Mischungen als Festelektrolyt in Eisenschmelzen bei 1640° C
Y1  - 1977
N1  - Dissertation, RWTH Aachen
CY  - Aachen
ER  - 
TY  - JOUR
A1  - Schwarzer, Klemens
T1  - Anwendung solarer Hochtemperaturwärme am Beispiel eines Solarkochers
JF  - Wege in die Solargesellschaft 4 : Dokumentation zur Vortragsreihe an der Fachhochschule Darmstadt in Zusammenarbeit mit dem IKU-Institut für kommunale Wirtschaft und Umweltplanung im Sommersemester 1993 / [Hrsg.: Projektgruppe Solarenergie an der Fachhochschule Darmstadt ; IKU-Inst. für Kommunale Wirtschaft u. Umweltplanung. Red.: Helmut C. Büscher]
Y1  - 1993
N1  - Ringvorlesung Wege in die Solargesellschaft  <4, 1993, Darmstadt>
SP  - 13
EP  - 24
PB  - FHD
CY  - Darmstadt
ER  - 
TY  - BOOK
A1  - Förster, Arnold
T1  - Anwendung der hochauflösenden Elektronenenergieverlustspektroskopie zum Studium von Halbleiterschichtsystemen. - (Berichte der Kernforschungsanlage Jülich / Kernforschungsanlage  ; 2247)
Y1  - 1988
N1  - Zugl.: Aachen, Techn. Hochsch., Diss., 1988
PB  - Zentralbibliothek der Kernforschungsanlage
CY  - Jülich
ER  - 
TY  - JOUR
A1  - Breitbach, Gerd
A1  - Altes, J.
A1  - Szimmat, J.
T1  - Anwendung der Finite-Element-Methode bei der Berechnung des Wärmetransports durch Strahlung / J. Altes ; G. Breitbach ; J. Szimmat
JF  - International FEM-Congress : Baden-Baden, Federal Republic of Germany, 17./18. November 1986
Y1  - 1989
N1  - International FEM Congress <15, 1986, Baden-Baden>
SP  - 127
EP  - 148
PB  - IKO Software Service GmbH
CY  - Stuttgart
ER  - 
TY  - BOOK
A1  - Breitbach, Gerd
A1  - Altes, Jürgen
T1  - Anwendung der Finite Elemente Methode auf Probleme mit Wärmestrahlungsaustausch
Y1  - 1985
N1  - (Berichte der Kernforschungsanlage Jülich / Kernforschungsanlage ; 2013)
PB  - Zentralbibliothek der Kernforschungsanlage
CY  - Jülich
ER  - 
TY  - JOUR
A1  - Förster, Arnold
A1  - Darmo, J.
A1  - Dubecky, F.
A1  - Kordos, P.
T1  - Annealing effect on concentration of EL6-like deep-level state in low-temperature-grown molecular beam epitaxial GaAs. Darmo, J.; Dubecky, F.; Kordos, P.; Förster, A.
JF  - Applied Physics Letters. 72 (1998), H. 5
Y1  - 1998
SN  - 1077-3118
SP  - 590
EP  - 592
ER  - 
TY  - JOUR
A1  - Förster, Arnold
A1  - Darmo, J.
A1  - Dubecký, F.
A1  - Kordos, P.
T1  - Annealing characteristics of native defects in low-temperature-grown MBE GaAs / J. Darmo ; F. Dubecky ; P. Kordos ; A. Förster
JF  - Semiconducting and insulating materials 1996 : proceedings of the 9th Conference on Semiconducting and Insulating Materials (SIMC '9), April 29 - May 3, 1996, Toulouse, France / [IEEE]
Y1  - 1996
SN  - 0-7803-3095-1
N1  - 2. ISBN: 0-7803-3179-6 ; Conference on Semiconducting and Insulating Materials <9, 1996, Toulouse> ; Institute of Electrical and Electronics Engineers ; IEEE Cat. No.96CH35881
SP  - 67
EP  - ff.
CY  - Piscataway, NJ [u.a.]
ER  - 
TY  - JOUR
A1  - Kern, Alexander
A1  - Zischank, Wolfgang
A1  - Beierl, Ottmar
T1  - Anmerkungen zur Berechnung des Trennungsabstands nach DIN EN 62305-3 (VDE 0185-305-3): 2006-10  / Zischank, Wolfgang ; Beierl, Ottmar ; Kern, Alexander
JF  - 7. VDE-ABB-Blitzschutztagung : Vorträge der VDE-ABB-Fachtagung vom 15. bis 16. November 2007 in Neu-Ulm / Veranst.: Ausschuss für Blitzschutz und Blitzforschung (ABB) im VDE, Verband der Elektrotechnik, Elektronik, Informationstechnik e.V. Wiss. Tagungsltg.: K. Stimper
Y1  - 2007
SN  - 978-3-8007-3062-9
N1  - VDE-Fachbericht ; 64  ; Blitzschutztagung <7, 2007, Neu-Ulm>
SP  - 1
EP  - 8
PB  - VDE-Verl.
CY  - Berlin
ER  - 
TY  - JOUR
A1  - Barsov, S.
A1  - Bechstedt, U.
A1  - Hardt, Arno
T1  - ANKE, a new facility for medium energy hadron physics at COSY-Jülich / S. Barsov [u.a.]
JF  - Nuclear instruments and methods in Physics Research Section A: Accelerators, Spectrometers, Detectors and Associated Equipment. Vol. 462, iss. 3
Y1  - 2001
SN  - 0167-5087 (Print) ; 0168-9002 (E-journal)
SP  - 364
EP  - 381
ER  - 
TY  - CHAP
A1  - Breitbach, Gerd
A1  - Alexopoulos, Spiros
A1  - May, Martin
A1  - Teixeira Boura, Cristiano José
A1  - Herrmann, Ulf
T1  - Analysis of volumetric solar radiation absorbers made of wire meshes
T2  - AIP Conference Proceedings
Y1  - 2019
U6  - https://doi.org/10.1063/1.5117521
SN  - 0094243X
VL  - 2126
SP  - 030009-1
EP  - 030009-6
ER  - 
TY  - JOUR
A1  - Butenweg, Christoph
A1  - Rosin, Julia
A1  - Holler, Stefan
T1  - Analysis of cylindrical granular material silos under seismic excitation
JF  - Buildings
N2  - Silos generally work as storage structures between supply and demand for various goods, and their structural safety has long been of interest to the civil engineering profession. This is especially true for dynamically loaded silos, e.g., in case of seismic excitation. Particularly thin-walled cylindrical silos are highly vulnerable to seismic induced pressures, which can cause critical buckling phenomena of the silo shell. The analysis of silos can be carried out in two different ways. In the first, the seismic loading is modeled through statically equivalent loads acting on the shell. Alternatively, a time history analysis might be carried out, in which nonlinear phenomena due to the filling as well as the interaction between the shell and the granular material are taken into account. The paper presents a comparison of these approaches. The model used for the nonlinear time history analysis considers the granular material by means of the intergranular strain approach for hypoplasticity theory. The interaction effects between the granular material and the shell is represented by contact elements. Additionally, soil–structure interaction effects are taken into account.
KW  - granular silo
KW  - earthquake engineering
KW  - hypoplasticity
KW  - nonlinear transient analyses
Y1  - 2017
U6  - https://doi.org/10.3390/buildings7030061
SN  - 2075-5309
VL  - 7
IS  - 3
SP  - 1
EP  - 12
PB  - MDPI
CY  - Basel
ER  - 
TY  - CHAP
A1  - Rosin, J.
A1  - Mykoniou, K.
A1  - Butenweg, Christoph
T1  - Analysis Of Base Isolated Liquid Storage Tanks With 3D Fsi-Analysis As Well As Simplified Approaches
T2  - 16th World Conference on Earthquake Engineering, 16WCEE 2017 Santiago Chile, January 9th to 13th 2017
N2  - Tanks are preferably designed, for cost-saving reasons, as circular, cylindrical, thin-walled shells. In case of seismic excitation, these constructions are highly vulnerable to stability failures. An earthquake-resistant design of rigidly supported tanks for high seismic loading demands, however, uneconomic wall thicknesses. A cost-effective alternative can be provided by base isolation systems. In this paper, a simplified seismic design procedure for base isolated tanks is introduced, by appropriately modifying the standard mechanical model for flexible, rigidly supported tanks. The non-linear behavior of conventional base isolation systems becomes an integral part of a proposed simplified process, which enables
the assessment of the reduced hydrodynamic forces acting on the tank walls and the corresponding stress distribution. The impulsive and convective actions of the liquid are taken into account. The validity of this approach is evaluated by
employing a non-linear fluid-structure interaction algorithm of finite element method. Special focus is placed on the boundary conditions imposed from the base isolation and the resulting hydrodynamic pressures. Both horizontal and vertical
component of ground motion are considered in order to study the principal effects of the base isolation on the pressure distribution of the tank walls. The induced rocking effects associated with elastomeric bearings are discussed. The results
manifest that base isolated tanks can be designed for seismic loads by means of the proposed procedure with sufficient accuracy, allowing to dispense with numerically expensive techniques.
KW  - liquid storage tank
KW  - seismic isolation
KW  - elastomeric bearing
KW  - friction pendulum bearing
KW  - simplified approach
Y1  - 2017
N1  - Paper No 2246
SP  - 1
EP  - 14
PB  - Chilean Association on Seismology and Earthquake Engineering (ACHISINA)
ER  - 
TY  - CHAP
A1  - Gedle, Yibekal
A1  - Schmitz, Mark
A1  - Gielen, Hans
A1  - Schmitz, Pascal
A1  - Herrmann, Ulf
A1  - Teixeira Boura, Cristiano José
A1  - Mahdi, Zahra
A1  - Chico Caminos, Ricardo Alexander
A1  - Dersch, Jürgen
T1  - Analysis of an integrated CSP-PV hybrid power plant
T2  - SOLARPACES 2020
N2  - In the past, CSP and PV have been seen as competing technologies. Despite massive reductions in the electricity generation costs of CSP plants, PV power generation is - at least during sunshine hours - significantly cheaper. If electricity is required not only during the daytime, but around the clock, CSP with its inherent thermal energy storage gets an advantage in terms of LEC. There are a few examples of projects in which CSP plants and PV plants have been co-located, meaning that they feed into the same grid connection point and ideally optimize their operation strategy to yield an overall benefit. In the past eight years, TSK Flagsol has developed a plant concept, which merges both solar technologies into one highly Integrated CSP-PV-Hybrid (ICPH) power plant. Here, unlike in simply co-located concepts, as analyzed e.g. in [1] – [4], excess PV power that would have to be dumped is used in electric molten salt heaters to increase the storage temperature, improving storage and conversion efficiency. The authors demonstrate the electricity cost sensitivity to subsystem sizing for various market scenarios, and compare the resulting optimized ICPH plants with co-located hybrid plants. Independent of the three feed-in tariffs that have been assumed, the ICPH plant shows an electricity cost advantage of almost 20% while maintaining a high degree of flexibility in power dispatch as it is characteristic for CSP power plants. As all components of such an innovative concept are well proven, the system is ready for commercial market implementation. A first project is already contracted and in early engineering execution.
KW  - Hybrid energy system
KW  - Power plants
KW  - Electricity generation
KW  - Energy storage
KW  - Associated liquids
Y1  - 2022
SN  - 978-0-7354-4195-8
U6  - https://doi.org/10.1063/5.0086236
SN  - 1551-7616 (online)
SN  - 0094-243X (print)
N1  - SOLARPACES 2020: 26th International Conference on Concentrating Solar Power and Chemical Energy Systems, 28 September–2 October 2020, Freiburg, Germany
IS  - 2445 / 1
PB  - AIP conference proceedings / American Institute of Physics
CY  - Melville, NY
ER  - 
TY  - JOUR
A1  - Block, Simon
A1  - Viebahn, Peter
A1  - Jungbluth, Christian
T1  - Analysing direct air capture for enabling negative emissions in Germany: an assessment of the resource requirements and costs of a potential rollout in 2045
JF  - Frontiers in Climate
N2  - Direct air capture (DAC) combined with subsequent storage (DACCS) is discussed as one promising carbon dioxide removal option. The aim of this paper is to analyse and comparatively classify the resource consumption (land use, renewable energy and water) and costs of possible DAC implementation pathways for Germany. The paths are based on a selected, existing climate neutrality scenario that requires the removal of 20 Mt of carbon dioxide (CO2) per year by DACCS from 2045. The analysis focuses on the so-called “low-temperature” DAC process, which might be more advantageous for Germany than the “high-temperature” one. In four case studies, we examine potential sites in northern, central and southern Germany, thereby using the most suitable renewable energies for electricity and heat generation. We show that the deployment of DAC results in large-scale land use and high energy needs. The land use in the range of 167–353 km2 results mainly from the area required for renewable energy generation. The total electrical energy demand of 14.4 TWh per year, of which 46% is needed to operate heat pumps to supply the heat demand of the DAC process, corresponds to around 1.4% of Germany's envisaged electricity demand in 2045. 20 Mt of water are provided yearly, corresponding to 40% of the city of Cologne‘s water demand (1.1 million inhabitants). The capture of CO2 (DAC) incurs levelised costs of 125–138 EUR per tonne of CO2, whereby the provision of the required energy via photovoltaics in southern Germany represents the lowest value of the four case studies. This does not include the costs associated with balancing its volatility. Taking into account transporting the CO2 via pipeline to the port of Wilhelmshaven, followed by transporting and sequestering the CO2 in geological storage sites in the Norwegian North Sea (DACCS), the levelised costs increase to 161–176 EUR/tCO2. Due to the longer transport distances from southern and central Germany, a northern German site using wind turbines would be the most favourable.
KW  - rollout
KW  - economics
KW  - Germany
KW  - negative emissions
KW  - carbon dioxide removal
KW  - climate neutrality
KW  - DAC
KW  - direct air capture
Y1  - 2024
U6  - https://doi.org/10.3389/fclim.2024.1353939
SN  - 2624-9553
VL  - 6
PB  - Frontiers
CY  - Lausanne
ER  - 
TY  - THES
A1  - Borchert, Jörg
T1  - Analyse von Determinanten der Großhandelspreise für Elektrizität anhand einer Systemstudie des deutschen Marktes
Y1  - 2003
N1  - Berlin, Techn. Univ., Diss., 2003
ER  - 
TY  - JOUR
A1  - Kuperjans, Isabel
A1  - Starke, M.
A1  - Esser, J.
A1  - [u.a.], 
T1  - Analyse und Konzeption von Energieanlagen unter ökologischen, wirtschaftlichen und technischen Gesichtspunkten
JF  - WLB : Umwelttechnik für Industrie und Kommune
Y1  - 2000
SN  - 0341-2679
VL  - 44
IS  - 11/12
SP  - 26
EP  - 29
ER  - 
TY  - JOUR
A1  - Förster, Arnold
A1  - Verghese, S.
A1  - Zamdmer, N.
A1  - Hu, Qing
T1  - An optical correlator using a low-temperature-grown GaAs photoconductor / S. Verghese ; N. Zamdmer ; Qing Hu .... A. Förster
JF  - Applied physics letters. 69 (1996), H. 6
Y1  - 1996
SN  - 0003-6951
N1  - ISSN der E-Ausg.: 1077-3118
SP  - 842
EP  - 844
ER  - 
TY  - CHAP
A1  - Pütz, Sebastian
A1  - Baier, Ralph
A1  - Brauner, Philipp
A1  - Brillowski, Florian
A1  - Dammers, Hannah
A1  - Liehner, Luca
A1  - Mertens, Alexander
A1  - Rodemann, Niklas
A1  - Schneider, Sebastian
A1  - Schollemann, Alexander
A1  - Steuer-Dankert, Linda
A1  - Vervier, Luisa
A1  - Gries, Thomas
A1  - Leicht-Scholten, Carmen
A1  - Nagel, Saskia K.
A1  - Piller, Frank T.
A1  - Schuh, Günther
A1  - Ziefle, Martina
A1  - Nitsch, Verena
T1  - An interdisciplinary view on humane interfaces for digital shadows in the internet of production
T2  - 2022 15th International Conference on Human System Interaction (HSI)
N2  - Digital shadows play a central role for the next generation industrial internet, also known as Internet of Production (IoP). However, prior research has not considered systematically how human actors interact with digital shadows, shaping their potential for success. To address this research gap, we assembled an interdisciplinary team of authors from diverse areas of human-centered research to propose and discuss design and research recommendations for the implementation of industrial user interfaces for digital shadows, as they are currently conceptualized for the IoP. Based on the four use cases of decision support systems, knowledge sharing in global production networks, human-robot collaboration, and monitoring employee workload, we derive recommendations for interface design and enhancing workers’ capabilities. This analysis is extended by introducing requirements from the higher-level perspectives of governance and organization.
KW  - digital twin
KW  - digital shadow
KW  - cyber-physical production system
KW  - human-machine interface
Y1  - 2022
SN  - 978-1-6654-6823-7 (Print)
SN  - 978-1-6654-6822-0 (Online)
U6  - https://doi.org/10.1109/HSI55341.2022.9869467
SN  - 2158-2246 (Print)
SN  - 2158-2254 (Online)
N1  - 15th International Conference on Human System Interaction (HSI), 28-31 July 2022, Melbourne, Australia.
PB  - IEEE
ER  - 
TY  - JOUR
A1  - Förster, Arnold
A1  - Marso, M.
A1  - Gersdorf, P.
A1  - Fox, A.
T1  - An InAlAs-InGaAs OPFET with responsivity above 200 A/W at 1.3-&#956;m wavelength. Marso, M.; Gersdorf, P.; Fox, A.; Hodel, U.; Lambertini, R.; Kordos, P.
JF  - IEEE Photonics Technology Letters. 11 (1999), H. 1
Y1  - 1999
SN  - 1041-1135
SP  - 117
EP  - 119
ER  - 
TY  - JOUR
A1  - Lück, Reinhard
A1  - Gerling, Ulrich
A1  - Predel, Bruno
T1  - An entropy paradox of the association model
JF  - Zeitschrift für Metallkunde : international journal of materials research and advanced techniques. Bd. 80, H. 4
Y1  - 1989
SN  - 0044-3093 ; 0179-4841
SP  - 270
EP  - 275
ER  -