TY - BOOK ED - Raatschen, Hans-Jürgen T1 - Ingenieurfreunde FH Aachen : 75 Jahre Förderverein; Elektrotechnik und Informationstechnik, Luft- und Raumfahrttechnik, Maschinenbau und Mechatronik / [Hrsg.: Ingenieurfreunde FH Aachen e. V. ; Red.: H. J. Raatschen] Y1 - 2010 SN - 978-3-941704-03-9 PB - Klinkenberg CY - Aachen ER - TY - JOUR A1 - Abbas, Karim A1 - Balc, Nicolae A1 - Bremen, Sebastian A1 - Skupin, Marco T1 - Crystallization and aging behavior of polyetheretherketone PEEK within rapid tooling and rubber molding JF - Journal of Manufacturing and Materials Processing N2 - In times of short product life cycles, additive manufacturing and rapid tooling are important methods to make tool development and manufacturing more efficient. High-performance polymers are the key to mold production for prototypes and small series. However, the high temperatures during vulcanization injection molding cause thermal aging and can impair service life. The extent to which the thermal stress over the entire process chain stresses the material and whether it leads to irreversible material aging is evaluated. To this end, a mold made of PEEK is fabricated using fused filament fabrication and examined for its potential application. The mold is heated to 200 ◦C, filled with rubber, and cured. A differential scanning calorimetry analysis of each process step illustrates the crystallization behavior and first indicates the material resistance. It shows distinct cold crystallization regions at a build chamber temperature of 90 ◦C. At an ambient temperature above Tg, crystallization of 30% is achieved, and cold crystallization no longer occurs. Additional tensile tests show a decrease in tensile strength after ten days of thermal aging. The steady decrease in recrystallization temperature indicates degradation of the additives. However, the tensile tests reveal steady embrittlement of the material due to increasing crosslinking. KW - additive manufacturing KW - fused filament fabrication KW - crystallization KW - polyetheretherketone KW - rapid tooling Y1 - 2022 U6 - http://dx.doi.org/10.3390/jmmp6050093 SN - 2504-4494 N1 - The article belongs to the Special Issue Advances in Injection Molding: Process, Materials and Applications VL - 6 IS - 5 SP - 1 EP - 12 PB - MDPI CY - Basel ER - TY - JOUR A1 - Abbas, Karim A1 - Hedwig, Lukas A1 - Balc, Nicolae A1 - Bremen, Sebastian T1 - Advanced FFF of PEEK: Infill strategies and material characteristics for rapid tooling JF - Polymers N2 - Traditional vulcanization mold manufacturing is complex, costly, and under pressure due to shorter product lifecycles and diverse variations. Additive manufacturing using Fused Filament Fabrication and high-performance polymers like PEEK offer a promising future in this industry. This study assesses the compressive strength of various infill structures (honeycomb, grid, triangle, cubic, and gyroid) when considering two distinct build directions (Z, XY) to enhance PEEK’s economic and resource efficiency in rapid tooling. A comparison with PETG samples shows the behavior of the infill strategies. Additionally, a proof of concept illustrates the application of a PEEK mold in vulcanization. A peak compressive strength of 135.6 MPa was attained in specimens that were 100% solid and subjected to thermal post-treatment. This corresponds to a 20% strength improvement in the Z direction. In terms of time and mechanical properties, the anisotropic grid and isotropic cubic infill have emerged for use in rapid tooling. Furthermore, the study highlights that reducing the layer thickness from 0.15 mm to 0.1 mm can result in a 15% strength increase. The study unveils the successful utilization of a room-temperature FFF-printed PEEK mold in vulcanization injection molding. The parameters and infill strategies identified in this research enable the resource-efficient FFF printing of PEEK without compromising its strength properties. Using PEEK in rapid tooling allows a cost reduction of up to 70% in tool production. KW - polyetheretherketone (PEEK) KW - rapid tooling KW - infill strategy KW - compression behavior KW - additive manufacturing KW - fused filament fabrication Y1 - 2023 U6 - http://dx.doi.org/10.3390/polym15214293 N1 - This article belongs to the Special Issue "Polymer Materials and Design Processes for Additively Manufactured Products" VL - 2023 IS - 15 PB - MDPI CY - Basel ER - TY - CHAP A1 - Abbas, Karim A1 - Thurn, Laura A1 - Kessler, Julia A1 - Eichler, Fabian T1 - Basic research of the consideration of additive manufactured lattice structures under thermoand fluid dynamic loads T2 - Modern technologies in manufacturing (MTeM 2019) Y1 - 2019 U6 - http://dx.doi.org/10.1051/matecconf/201929901009 N1 - MATEC Web of Conferences 299; MTeM 2019 VL - 299 IS - Article 01009 ER - TY - JOUR A1 - Abdel-Latif, Lotfie Ahmed A1 - Peeken, Heinz A1 - Benner, Joachim T1 - Thermohydrodynamic analysis of thrust-bearing with circular pads running on bubbly oil (BTHD-theory) JF - Journal of tribology Y1 - 1985 SN - 0742-4787 SN - 1528-8897 VL - 107 IS - 4 SP - 527 EP - 537 ER - TY - JOUR A1 - Abdel-Latif, Lotfie Ahmed A1 - Peeken, Heinz A1 - Benner, Joachim T1 - Термогидродинамический расчет упорных подшипников с круговыми подушками на масляной пленке, содержащей пузырьки газа JF - Проблемы трения и смазки Y1 - 1985 N1 - Russ. Parallelausg. zum gleichzeitig ersch. Titel in der Zeitschr. "Journal of Tribology", 107(1985), 4 VL - 107 IS - 4 SP - 94 EP - 102 ER - TY - CHAP A1 - Adenacker, J. A1 - Gerhards, Benjamin A1 - Otten, Christian A1 - Schleser, Markus T1 - Laserstrahlschweißen von Aluminium-Kupfer-Werkstoffkombinationen für die Elektromobilität T2 - DVS CONGRESS 2021 Y1 - 2021 SN - 978-3-96144-146-4 N1 - DVS CONGRESS 2021, 14. – 17. September 2021, Essen. Große Schweißtechnische Tagung 2021, DVS CAMPUS 2021. DVS Berichte, Band: 371 SP - 31 EP - 38 PB - DVS Media GmbH CY - Düsseldorf ER - TY - CHAP A1 - Adomeit, G. A1 - Willms, Herbert ED - Skupinski, Edwin T1 - Experimental investigation of the acceleration of deflagration in wake flow T2 - Safety of thermal water reactors : proceedings of a Seminar on the Results of the European Communities’ Indirect Action Research Programme on Safety of Thermal Water Reactors, held in Brussels, 1–3 October 1984 / Commission of the European Communities Y1 - 1984 SN - 0-86010-678-0 SN - 978-94-009-4972-0 (Online-Nachdr. vom Springer-Verl.) N1 - Forschungsvorhaben Nr. 024 SRD SP - 294 EP - 304 PB - Graham & Trotman [u.a.] CY - London Gaithersburg, Md. ER - TY - RPRT A1 - Adomeit, G. A1 - Willms, Herbert T1 - Experimental investigation of the acceleration of deflagration in wake flow : final report. - (Euratom-publications-EUR ; 9593 : Nuclear science and technology) Y1 - 1984 SN - 92-825-4699-3 PB - Commission of the European Communities CY - Luxembourg ER - TY - JOUR A1 - Ahmed, Essam A1 - Reisgen, Uwe A1 - Schleser, Markus A1 - Mokrov, Oleg T1 - On formability of tailor laser welded blanks of DP/TRIP steel sheets JF - Science and technology of welding and joining N2 - This paper aims to evaluate the formability of tailor welded blanks of dual phase (DP600)/transformation induced plasticity (TRIP700) steel sheets. In this work, bead on plate butt joints of 2·5 mm DP600 and 1·2 mm TRIP700 steel sheets were performed using CO2 laser beam welding. Microhardness measurements and transverse tensile testing were carried out to characterise the welds. The formability of base metals and welds were investigated by standard Erichsen test. In a perpendicular tensile test to the weld line, all specimens were fractured at the TRIP base metal, and the strengths were somewhat higher than those of base metal. There was a significant reduction in formability caused by welding of the DP600/TRIP700 steel sheets, and the formability increased with increasing welding speed. Y1 - 2010 U6 - http://dx.doi.org/10.1179/136217110X12731414739754 SN - 1743-2936 VL - 15 IS - 5 SP - 337 EP - 342 PB - Maney CY - Leeds ER -