TY - JOUR A1 - Luft, Angela A1 - Bremen, Sebastian A1 - Luft, Nils T1 - A cost/benefit and flexibility evaluation framework for additive technologies in strategic factory planning JF - Processes N2 - There is a growing demand for more flexibility in manufacturing to counter the volatility and unpredictability of the markets and provide more individualization for customers. However, the design and implementation of flexibility within manufacturing systems are costly and only economically viable if applicable to actual demand fluctuations. To this end, companies are considering additive manufacturing (AM) to make production more flexible. This paper develops a conceptual model for the impact quantification of AM on volume and mix flexibility within production systems in the early stages of the factory-planning process. Together with the model, an application guideline is presented to help planners with the flexibility quantification and the factory design process. Following the development of the model and guideline, a case study is presented to indicate the potential impact additive technologies can have on manufacturing flexibility Within the case study, various scenarios with different production system configurations and production programs are analyzed, and the impact of the additive technologies on volume and mix flexibility is calculated. This work will allow factory planners to determine the potential impacts of AM on manufacturing flexibility in an early planning stage and design their production systems accordingly. KW - additive manufacturing KW - factory planning KW - manufacturing flexibility KW - volume flexibility KW - mix flexibility Y1 - 2023 U6 - http://dx.doi.org/10.3390/pr11071968 SN - 2227-9717 VL - 11 IS - 7 PB - MDPI CY - Basel ER - TY - JOUR A1 - Pfaff, Raphael A1 - Enning, Manfred A1 - Sutter, Stefan T1 - A risk‑based approach to automatic brake tests for rail freight service: incident analysis and realisation concept JF - SN Applied Sciences N2 - This study reviews the practice of brake tests in freight railways, which is time consuming and not suitable to detect certain failure types. Public incident reports are analysed to derive a reasonable brake test hardware and communication architecture, which aims to provide automatic brake tests at lower cost than current solutions. The proposed solutions relies exclusively on brake pipe and brake cylinder pressure sensors, a brake release position switch as well as radio communication via standard protocols. The approach is embedded in the Wagon 4.0 concept, which is a holistic approach to a smart freight wagon. The reduction of manual processes yields a strong incentive due to high savings in manual labour and increased productivity. KW - Freight rail KW - Brake test KW - Incident analysis KW - Train composition KW - Brake set-up Y1 - 2022 U6 - http://dx.doi.org/10.1007/s42452-022-05007-x SN - 2523-3971 N1 - Corresponding author: Raphael Pfaff VL - 4 IS - 4 SP - 1 EP - 14 PB - Springer CY - Cham ER - TY - JOUR A1 - Engemann, Heiko A1 - Cönen, Patrick A1 - Dawar, Harshal A1 - Du, Shengzhi A1 - Kallweit, Stephan T1 - A robot-assisted large-scale inspection of wind turbine blades in manufacturing using an autonomous mobile manipulator JF - Applied Sciences N2 - Wind energy represents the dominant share of renewable energies. The rotor blades of a wind turbine are typically made from composite material, which withstands high forces during rotation. The huge dimensions of the rotor blades complicate the inspection processes in manufacturing. The automation of inspection processes has a great potential to increase the overall productivity and to create a consistent reliable database for each individual rotor blade. The focus of this paper is set on the process of rotor blade inspection automation by utilizing an autonomous mobile manipulator. The main innovations include a novel path planning strategy for zone-based navigation, which enables an intuitive right-hand or left-hand driving behavior in a shared human–robot workspace. In addition, we introduce a new method for surface orthogonal motion planning in connection with large-scale structures. An overall execution strategy controls the navigation and manipulation processes of the long-running inspection task. The implemented concepts are evaluated in simulation and applied in a real-use case including the tip of a rotor blade form. KW - mobile manipulation KW - large-scale inspection KW - wind turbine production KW - autonomous navigation KW - surface-orthogonal path planning Y1 - 2021 U6 - http://dx.doi.org/10.3390/app11199271 SN - 2076-3417 N1 - Belongs to the Special Issue "Advances in Industrial Robotics and Intelligent Systems" VL - 11 IS - 19 SP - 1 EP - 22 PB - MDPI CY - Basel ER - TY - JOUR A1 - Gebhardt, Andreas T1 - Generative Manufacturing of Ceramic Parts "Vision Rapid Prototyping" N2 - Table of Contents Introduction 1. Generative Manufacturing Processes 2. Classification of Generative Manufacturing Processes 3. Application of Generative Processes on the Fabrication of Ceramic Parts 3.1 Extrusion 3.2 3D-Printing 3.3 Sintering – Laser Sintering 3.4 Layer-Laminate Processes 3.5 Stereolithography (sometimes written: Stereo Lithography) 4. Layer Milling 5. Conclusion - Vision KW - Rapid prototyping KW - Rapid Technologie KW - Rapid Prototyping Y1 - 2006 ER - TY - CHAP A1 - Reisgen, Uwe A1 - Schoene, Jens A1 - Schleser, Markus A1 - Gries, Thomas A1 - Glowania, Michael T1 - Impregnated textile reinforcements for concrete applications T2 - European Coatings Congress : Nürnberg, Germany, 30.3. - 1.4. 2009 Y1 - 2009 ER - TY - CHAP A1 - Schleser, Markus A1 - Dilthey, Ulrich A1 - Mund, F. A1 - Böhm, Stefan ED - Czarnecki, Lech ED - Garbacz, Andrzej T1 - Improvement of textile reinforced concrete by use of polymers T2 - Adhesion in interfaces of building materials: a multi-scale approach : [Symposium "Adhesion in Building Bonds: Macro-, Micro- and Nano-Scale" at Warsaw University of Technology in the framework of the European Materials Research Society, fall meeting 2005 ; selected papers]. (Advances in materials science and restoration. No. 2) Y1 - 2007 SN - 978-3-931681-89-0 SP - 153 EP - 162 PB - Aedificatio Publ. CY - Freiburg ER - TY - CHAP A1 - Dilthey, Ulrich A1 - Schleser, Markus A1 - Puterman, Moshe T1 - Investigation and improvement of concrete reinforced with epoxy impregnated fabrics T2 - Proceedings / 12th International Congress Polymers in Concrete, ICPIC 07, chuncheon, Korea, Sept. 26. - 28., 2007 Y1 - 2007 SN - 978-89-9600450-9 SP - 725 EP - 733 PB - Kangwoon National Univ. CY - Chancheon ER - TY - CHAP A1 - Ferrein, Alexander A1 - Kallweit, Stephan A1 - Scholl, Ingrid A1 - Reichert, Walter T1 - Learning to Program Mobile Robots in the ROS Summer School Series T2 - Proceedings 6th International Conference on Robotics in Education (RiE 15) N2 - The main objective of our ROS Summer School series is to introduce MA level students to program mobile robots with the Robot Operating System (ROS). ROS is a robot middleware that is used my many research institutions world-wide. Therefore, many state-of-the-art algorithms of mobile robotics are available in ROS and can be deployed very easily. As a basic robot platform we deploy a 1/10 RC cart that is wquipped with an Arduino micro-controller to control the servo motors, and an embedded PC that runs ROS. In two weeks, participants get to learn the basics of mobile robotics hands-on. We describe our teaching concepts and our curriculum and report on the learning success of our students. Y1 - 2015 ER - TY - GEN A1 - Kämper, Klaus-Peter T1 - Lecture notes Sensors and Actuators N2 - Kennwortgeschützter Zugang nur für Studierende bei Prof. Dr. Klaus-Peter Kämper. Wintersemester 2007/2008. Version vom 30.08.2007. 472 Seiten (pdf-Format) N2 - Password necessarily. Access only for Students by Prof. Dr. Klaus-Peter Kämper. Winter semester 2007/2008. Version 2007-08-30. 472 pages (pdf) Contents 1. Introduction 2. Introduction to Sensors 3. Introduction to Microfabrication 4. Pressure Sensors 5. Acceleration Sensors 6. Angular Rate Sensors 7. Position Sensors 8. Flow Sensors 9. Piezoelectric Actuators 10. Magnetostrictive Actuators 11. Actuators based on Shape Memory Alloys 12. Actuators based on Electrorheological Fluids 13. Actuators based on Magnetorheological Fluids KW - Sensor KW - Aktor KW - Sensoren KW - Aktoren KW - Sensores KW - Actuators KW - Microfabrication Y1 - 2007 ER - TY - GEN A1 - Kämper, Klaus-Peter T1 - Lecture notes Sensors and Actuators WS 2008/2009 N2 - Password necessarily. Access only for Students by Prof. Dr. Klaus-Peter Kämper. Winter semester 2008/2009. 488 pages (pdf) Contents 1. Introduction 2. Introduction to Sensors 3. Introduction to Microfabrication 4. Pressure Sensors 5. Acceleration Sensors 6. Angular Rate Sensors 7. Position Sensors 8. Flow Sensors 9. Piezoelectric Actuators 10. Magnetostrictive Actuators 11. Actuators based on Shape Memory Alloys 12. Actuators based on Electrorheological Fluids 13. Actuators based on Magnetorheological Fluids 14. Index N2 - Kennwortgeschützter Zugang nur für Studierende bei Prof. Dr. Klaus-Peter Kämper. Wintersemester 2008/2009. 488 Seiten (pdf-Format) KW - Sensor KW - Aktor KW - Sensoren KW - Aktoren KW - Sensores KW - Actuators KW - Microfabrication Y1 - 2008 ER -