TY - JOUR A1 - Kampker, Achim A1 - Schleser, Markus A1 - Triebs, Johannes A1 - Berg, Alexander-Karl A1 - Hansen, Jan Ole A1 - Fiedler, Falko T1 - Bauteilintegrierte Vorrichtungsfunktionen im Karosseriebau : Aktuelle Ergebnisse im Forschungsprojekt ProeK JF - ZWF Zeitschrift für wirtschaftlichen Fabrikbetrieb N2 - Das Forschungsprojekt Produktionseffizienz in der Kleinserie (ProeK) erarbeitet kostengünstige und effiziente Lösungsansätze für Prozessketten im Zukunftsfeld der Elektromobilität. Das Teilprojekt Karosserie setzt diese Zielsetzung durch innovative und praxisorientierte Produkt- und Prozesskonzepte mit neuartigen bauteilintegrierten Vorrichtungsfunktionen (BiV) um. Im Teilprojekt Außenhaut sollen Toleranzen adaptiv durch Anpassungen der Prozessparameter sowie Bauteilmanipulation kompensiert werden. Y1 - 2018 U6 - http://dx.doi.org/10.3139/104.112012 SN - 0947-0085 VL - 113 IS - 11 SP - 767 EP - 770 PB - De Gruyter CY - Berlin ER - TY - JOUR A1 - Wollert, Jörg T1 - Echtzeit-Ethernet – Basis für Industrie 4.0 JF - Design & Elektronik Y1 - 2018 SN - 0933-8667 N1 - Echtzeit für Industrie 4.0. - Teil 2 PB - WEKA-Fachmedien CY - München ER - TY - JOUR A1 - Schmidt, Bernd A1 - Enning, Manfred A1 - Pfaff, Raphael T1 - Güterwagen 4.0 – Der Güterwagen für das Internet der Dinge Teil 3: Einführungsszenarien für aktive, kommunikative Güterwagen JF - ETR - Eisenbahntechnische Rundschau N2 - Wenn durch innovative, automatisierte Güterwagen betriebswirtschaftliche Vorteile nutzbar gemacht werden sollen, muss die Migration auf das neue System in sinnvollen Teilschritten unter Berücksichtigung der organisationellen und betrieblichen Vereinbarkeit vorgenommen werden. Eine stufenweise Migration mit Nachrüstbarkeit und Kompatibilität kann die optimale Ausstattungsvariante für die unterschiedlichen Betriebsszenarien sowie eine Steigerung der Wirtschaftlichkeit des Gesamtsystems bieten. Y1 - 2018 SN - 0013-2845 VL - 67 IS - 5 SP - 60 EP - 64 PB - DVV Media Group CY - Hamburg ER - TY - JOUR A1 - Ziebura, Dawid A1 - Bremen, Sebastian A1 - Schleifenbaum, Johannes Henrich A1 - Gebhardt, Andreas T1 - Machbarkeitsstudie zur Verarbeitung von nicht rostendem Stahl 1.4404 unter Verwendung einer Diodenlaser-basierten LPBF-Maschine mit kartesischem Achssystem JF - RTejournal - Forum für Rapid Technologie Y1 - 2018 SN - 1614-0923 VL - 15 ER - TY - JOUR A1 - Franzen, Julius A1 - Pinders, Erik A1 - Pfaff, Raphael A1 - Enning, Manfred T1 - RailCrowd’s virtual fleets: Make most of your asset data JF - Deine Bahn N2 - For smaller railway operators or those with a diverse fleet, it can be difficult to collect sufficient data to improve maintenance programs. At the same time, new rules such as entity in charge of maintenance – ECM – regulations impose an additional workload by requiring a dedicated maintenance management system and specific reports. The RailCrowd platform sets out to facilitate compliance with ECM and similar regulations while at the same time pooling anonymised fleet data across operators to form virtual fleets, providing greater data insights. Y1 - 2018 SN - 0948-7263 IS - 9 SP - 11 EP - 13 PB - Bahn-Fachverlag CY - Berlin ER - TY - JOUR A1 - Michaux, F. A1 - Mattern, P. A1 - Kallweit, Stephan T1 - RoboPIV: how robotics enable PIV on a large industrial scale JF - Measurement Science and Technology N2 - This work demonstrates how the interaction between particle image velocimetry (PIV) and robotics can massively increase measurement efficiency. The interdisciplinary approach is shown using the complex example of an automated, large scale, industrial environment: a typical automotive wind tunnel application. Both the high degree of flexibility in choosing the measurement region and the complete automation of stereo PIV measurements are presented. The setup consists of a combination of three robots, individually used as a 6D traversing unit for the laser illumination system as well as for each of the two cameras. Synchronised movements in the same reference frame are realised through a master-slave setup with a single interface to the user. By integrating the interface into the standard wind tunnel management system, a single measurement plane or a predefined sequence of several planes can be requested through a single trigger event, providing the resulting vector fields within minutes. In this paper, a brief overview on the demands of large scale industrial PIV and the existing solutions is given. Afterwards, the concept of RoboPIV is introduced as a new approach. In a first step, the usability of a selection of commercially available robot arms is analysed. The challenges of pose uncertainty and importance of absolute accuracy are demonstrated through comparative measurements, explaining the individual pros and cons of the analysed systems. Subsequently, the advantage of integrating RoboPIV directly into the existing wind tunnel management system is shown on basis of a typical measurement sequence. In a final step, a practical measurement procedure, including post-processing, is given by using real data and results. Ultimately, the benefits of high automation are demonstrated, leading to a drastic reduction in necessary measurement time compared to non-automated systems, thus massively increasing the efficiency of PIV measurements. Y1 - 2018 U6 - http://dx.doi.org/10.1088/1361-6501/aab5c1 SN - 1361-6501 N1 - Special Section on the 12th International Symposium on Particle Image Velocimetry (PIV 2017) VL - 29 IS - 7 SP - 074009 PB - IOP CY - Bristol ER - TY - JOUR A1 - Babilon, Katharina A1 - Wilbring, Daniela A1 - Tappert, Tim A1 - Pfaff, Raphael A1 - Enning, Manfred T1 - Schienenfahrzeugtechnik hands on – FH Aachen IMechE Railway Challenge JF - Ingenieurspiegel Y1 - 2018 SN - 1868-5919 IS - 2 SP - 20 EP - 22 PB - Public Verlag CY - Bingen ER - TY - JOUR A1 - Kunkel, Maximilian Hugo A1 - Gebhardt, Andreas A1 - Mpofu, Khumbaulani A1 - Kallweit, Stephan T1 - Statistical assessment of mechanical properties of selective laser melted specimens of stainless steel JF - The International Journal of Advanced Manufacturing Technology N2 - The rail business is challenged by long product life cycles and a broad spectrum of assembly groups and single parts. When spare part obsolescence occurs, quick solutions are needed. A reproduction of obsolete parts is often connected to long waiting times and minimum lot quantities that need to be purchased and stored. Spare part storage is therefore challenged by growing stocks, bound capital and issues of part ageing. A possible solution could be a virtual storage of spare parts which will be 3D printed through additive manufacturing technologies in case of sudden demand. As mechanical properties of additive manufactured parts are neither guaranteed by machine manufacturers nor by service providers, the utilization of this relatively young technology is impeded and research is required to address these issues. This paper presents an examination of mechanical properties of specimens manufactured from stainless steel through the selective laser melting (SLM) process. The specimens were produced in multiple batches. This paper interrogates the question if the test results follow a normal distribution pattern and if mechanical property predictions can be made. The results will be put opposite existing threshold values provided as the industrial standard. Furthermore, probability predictions will be made in order to examine the potential of the SLM process to maintain state-of-the-art mechanical property requirements. Y1 - 2018 U6 - http://dx.doi.org/10.1007/s00170-018-2040-8 SN - 0268-3768 VL - 98 IS - 5-8 SP - 1409 EP - 1431 PB - Springer CY - London ER - TY - JOUR A1 - Thomas, Axel T1 - Technologiezentren in der Aachener Region – Retrospektiven und Perspektiven JF - VM Verwaltung und Management Y1 - 2018 U6 - http://dx.doi.org/10.5771/0947-9856-2018-3-147 SN - 0947-9856 VL - 24 IS - 3 SP - 147 EP - 156 PB - Nomos CY - Baden-Baden ER - TY - JOUR A1 - Wollert, Jörg T1 - TSN – Schluss mit dem Feldbuskrieg? JF - Design & Elektronik Y1 - 2018 SN - 0933-8667 N1 - Echtzeit für Industrie 4.0. - Teil 3 IS - 3 SP - 26 EP - 31 PB - WEKA-Fachmedien CY - München ER -