TY - JOUR A1 - Hötter, Jan-Steffen A1 - Fateri, Miranda A1 - Gebhardt, Andreas T1 - Prozessoptimierung des SLM-Prozesses mit hoch-reflektiven und thermisch sehr gut leitenden Materialien durch systematische Parameterfindung und begleitende Simulationen am Beispiel von Silber JF - RTejournal - Forum für Rapid Technologie N2 - Additive Manufacturing durch Aufschmelzen von Metallpulvern hat sich auf breiter Front als Herstellverfahren, auch für Endprodukte, etabliert. Besonders für die Variante des Selective Laser Melting (SLM) sind Anwendungen in der Zahntechnik bereits weit verbreitet und der Einsatz in sensitiven Branchen wie der Luftfahrt ist in greifbare Nähe gerückt. Deshalb werden auch vermehrt Anstrengungen unternommen, um bisher nicht verarbeitete Materialien zu qualifizieren. Dies sind vorzugsweise Nicht-Eisen- und Edelmetalle, die sowohl eine sehr hohe Reflektivität als auch eine sehr gute Wärmeleitfähigkeit aufweisen – beides Eigenschaften, die die Beherrschung des Laser-Schmelzprozesses erschweren und nur kleine Prozessfenster zulassen. Die Arbeitsgruppe SLM des Lehr- und Forschungsgebietes Hochleistungsverfahren der Fertigungstechnik hat sich unter der Randbedingung einer kleinen und mit geringer Laserleistung ausgestatteten SLM Maschine der Aufgabe gewidmet und am Beispiel von Silber die Parameterfelder für Einzelspuren und wenig komplexe Geometrien systematisch untersucht. Die Arbeiten wurden von FEM Simulationen begleitet und durch metallographische Untersuchungen verifiziert. Die Ergebnisse bilden die Grundlage zur schnellen Parameterfindung bei komplexen Geometrien und bei Veränderungen der Zusammensetzung, wie sie bei zukünftigen Legierungen zu erwarten sind. Die Ergebnisse werden exemplarisch auf unterschiedliche Geometrien angewandt und entsprechende Bauteile gezeigt. N2 - Additive manufacturing by melting of metal powders is a method that has been established even for the manufacturing of final products. In particular, Selective Laser Melting (SLM) is currently applied for prosthetic dentistry. In the near future, this technology will access sensitive industries like aerospace engineering. This leads to the need to process new materials. Therefore, especially non-ferrous metals and noble metals must be determined and qualified. These materials have in common a very high reflectivity and an excellent thermal conductivity. In general, these two properties counteract the control of the melt pool and contribute to very narrow process windows. The “SLM” research team of the Aachen University of Applied Science, AcUAS (FH Aachen) systematically investigated process parameter fields for silver. The work focused on a small SLM desktop machine with comparably low laser power. The results are verified using FEA and metallographic inspections and will support future set-ups for complex geometries. Furthermore, the obtained parameter fields are applied to make different geometric objects and to manufactured parts, which are presented. KW - SLM KW - Selektives Laser Schmelzen KW - Silber Y1 - 2012 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:0009-2-33639 SN - 1614-0923 VL - 9 IS - 1 SP - 1 EP - 14 PB - Fachhoschule Aachen CY - Aachen ER - TY - JOUR A1 - Starke, Günther T1 - Prozesssteuerung und Automatisierung in der Schweisstechnik Y1 - 1984 N1 - Konferenz-Einzelbericht : Vortragsband zum Aachener Kolloquium. Schweissen mit Robotern, Aachen, 16.04.1984-17.04.1984 SP - 341 EP - 351 ER - TY - JOUR A1 - Starke, Günther T1 - Prozeßkontrolle und Prozeßsteuerung für die Fertigung in schweißtechnischen Betrieben Y1 - 1998 N1 - Konferenz-Einzelbericht : Duisburger Schweißtage, Duisburg, DE, 28.-29.05.1998 SP - 45 EP - 52 ER - TY - JOUR A1 - Raffeis, Iris A1 - Adjei-Kyeremeh, Frank A1 - Vroomen, Uwe A1 - Westhoff, Elmar A1 - Bremen, Sebastian A1 - Hohoi, Alexandru A1 - Bührig-Polaczek, Andreas T1 - Qualification of a Ni-Cu alloy for the laser powder bed fusion process (LPBF): Its microstructure and mechanical properties JF - Applied Sciences N2 - As researchers continue to seek the expansion of the material base for additive manufacturing, there is a need to focus attention on the Ni–Cu group of alloys which conventionally has wide industrial applications. In this work, the G-NiCu30Nb casting alloy, a variant of the Monel family of alloys with Nb and high Si content is, for the first time, processed via the laser powder bed fusion process (LPBF). Being novel to the LPBF processes, optimum LPBF parameters were determined, and hardness and tensile tests were performed in as-built conditions and after heat treatment at 1000 °C. Microstructures of the as-cast and the as-built condition were compared. Highly dense samples (99.8% density) were achieved after varying hatch distance (80 µm and 140 µm) with scanning speed (550 mm/s–1500 mm/s). There was no significant difference in microhardness between varied hatch distance print sets. Microhardness of the as-built condition (247 HV0.2) exceeded the as-cast microhardness (179 HV0.2.). Tensile specimens built in vertical (V) and horizontal (H) orientations revealed degrees of anisotropy and were superior to conventionally reported figures. Post heat treatment increased ductility from 20% to 31% (V), as well as from 16% to 25% (H), while ultimate tensile strength (UTS) and yield strength (YS) were considerably reduced. Y1 - 2020 U6 - http://dx.doi.org/10.3390/app10103401 SN - 2076-3417 N1 - Special Issue Materials Development by Additive Manufacturing Techniques VL - 10 IS - Art. 3401 SP - 1 EP - 15 PB - MDPI CY - Basel ER - TY - JOUR A1 - Starke, Günther A1 - Drews, P. T1 - Qualitaetssicherung in der automatisierten schweisstechnischen Fertigung durch Einsatz von Sensoren JF - Sensor. 6 (1983) Y1 - 1983 N1 - Konferenz-Einzelbericht : SENSOR '83. Tranducer-Technik: Entwicklung und Anwendung. Schweizer Mustermesse, Basel, 17.-19.5.1983 SP - 29 EP - 45 ER - TY - JOUR A1 - Starke, Günther A1 - Drews, P. T1 - Qualitaetssicherung in der automatisierten schweisstechnischen Fertigung durch Einsatz von Sensoren JF - Technisches Messen tm. 50 (1983), H. 12 Y1 - 1983 SN - 0171-8096 SP - 467 EP - 473 ER - TY - JOUR A1 - Kunkel, Maximilian Hugo A1 - Gebhardt, Andreas A1 - Mpofu, Khumbulani A1 - Kallweit, Stephan T1 - Quality assurance in metal powder bed fusion via deep-learning-based image classification JF - Rapid Prototyping Journal Y1 - 2019 U6 - http://dx.doi.org/10.1108/RPJ-03-2019-0066 SN - 1355-2546 VL - 26 IS - 2 SP - 259 EP - 266 ER - TY - JOUR A1 - Franzen, Julius A1 - Pinders, Erik A1 - Pfaff, Raphael A1 - Enning, Manfred T1 - RailCrowd’s virtual fleets: Make most of your asset data JF - Deine Bahn N2 - For smaller railway operators or those with a diverse fleet, it can be difficult to collect sufficient data to improve maintenance programs. At the same time, new rules such as entity in charge of maintenance – ECM – regulations impose an additional workload by requiring a dedicated maintenance management system and specific reports. The RailCrowd platform sets out to facilitate compliance with ECM and similar regulations while at the same time pooling anonymised fleet data across operators to form virtual fleets, providing greater data insights. Y1 - 2018 SN - 0948-7263 IS - 9 SP - 11 EP - 13 PB - Bahn-Fachverlag CY - Berlin ER - TY - JOUR A1 - Gebhardt, Andreas T1 - Rapid Prototyping JF - Landolt-Börnstein - Group VIII Advanced Materials and Technologies‡Vol. 1 Laser Physics and Applications‡Subvol. C Laser Applications / authors: Bäuerle, D. ... Y1 - 2004 SN - 3-540-00105-0 SP - 105 EP - 123 PB - Heidelberg CY - Springer ER - TY - JOUR A1 - Gebhardt, Andreas T1 - Rapid Prototyping - Laser-gestützte Revolution der Produktentwicklung. Teil I JF - Laser Magazin (1996) Y1 - 1996 SN - 0945-8875 SP - 6 EP - 9 ER -