TY - JOUR A1 - Kampker, Achim A1 - Schleser, Markus A1 - Triebs, Johannes A1 - Berg, Alexander-Karl A1 - Hansen, Jan Ole A1 - Fiedler, Falko T1 - Bauteilintegrierte Vorrichtungsfunktionen im Karosseriebau : Aktuelle Ergebnisse im Forschungsprojekt ProeK JF - ZWF Zeitschrift für wirtschaftlichen Fabrikbetrieb N2 - Das Forschungsprojekt Produktionseffizienz in der Kleinserie (ProeK) erarbeitet kostengünstige und effiziente Lösungsansätze für Prozessketten im Zukunftsfeld der Elektromobilität. Das Teilprojekt Karosserie setzt diese Zielsetzung durch innovative und praxisorientierte Produkt- und Prozesskonzepte mit neuartigen bauteilintegrierten Vorrichtungsfunktionen (BiV) um. Im Teilprojekt Außenhaut sollen Toleranzen adaptiv durch Anpassungen der Prozessparameter sowie Bauteilmanipulation kompensiert werden. Y1 - 2018 U6 - http://dx.doi.org/10.3139/104.112012 SN - 0947-0085 VL - 113 IS - 11 SP - 767 EP - 770 PB - De Gruyter CY - Berlin ER - TY - CHAP A1 - Kasch, Susanne A1 - Schmidt, Thomas A1 - Eichler, Fabian A1 - Thurn, Laura A1 - Jahn, Simon A1 - Bremen, Sebastian T1 - Solution approaches and process concepts for powder bed-based melting of glass T2 - Industrializing Additive Manufacturing. Proceedings of AMPA2020 N2 - In the study, the process chain of additive manufacturing by means of powder bed fusion will be presented based on the material glass. In order to reliably process components additively, new concepts with different solutions were developed and investigated. Compared to established metallic materials, the properties of glass materials differ significantly. Therefore, the process control was adapted to the material glass in the investigations. With extensive parameter studies based on various glass powders such as borosilicate glass and quartz glass, scientifically proven results on powder bed fusion of glass are presented. Based on the determination of the particle properties with different methods, extensive investigations are made regarding the melting behavior of glass by means of laser beams. Furthermore, the experimental setup was steadily expanded. In addition to the integration of coaxial temperature measurement and regulation, preheating of the building platform is of major importance. This offers the possibility to perform 3D printing at the transformation temperatures of the glass materials. To improve the component’s properties, the influence of a subsequent heat treatment was also investigated. The experience gained was incorporated into a new experimental system, which allows a much better exploration of the 3D printing of glass. Currently, studies are being conducted to improve surface texture, building accuracy, and geometrical capabilities using three-dimensional specimen. The contribution shows the development of research in the field of 3D printing of glass, gives an insight into the machine and process engineering as well as an outlook on the possibilities and applications. KW - Glass powder KW - Laser processing KW - Additive manufacturing KW - Melting KW - L-PBF Y1 - 2020 SN - 978-3-030-54333-4 (Print) SN - 978-3-030-54334-1 (Online) U6 - http://dx.doi.org/10.1007/978-3-030-54334-1_7 N1 - International Conference on Additive Manufacturing in Products and Applications. 01.-03. September 2020. Zurich, Switzerland SP - 82 EP - 95 PB - Springer CY - Cham ER - TY - JOUR A1 - Kasch, Susanne A1 - Schmidt, Thomas A1 - Jahn, Simon A1 - Eichler, Fabian A1 - Thurn, Laura A1 - Bremen, Sebastian T1 - Lösungsansätze und Verfahrenskonzepte zum Laserstrahlschmelzen von Glas JF - Schweissen und Schneiden Y1 - 2021 SN - 0036-7184 VL - 73 IS - Heft 1-2 SP - 32 EP - 39 PB - DVS Verlag CY - Düsseldorf ER - TY - CHAP A1 - Kessler, Julia A1 - Balc, Nicolae A1 - Gebhardt, Andreas T1 - Basic research on lattice structures focused on the strut shape and welding beads T2 - Physics Procedia Y1 - 2016 U6 - http://dx.doi.org/10.1016/j.phpro.2016.08.086 SN - 1875-3884 N1 - Laser Assisted Net Shape Engineering 9th International Conference on Photonic Technologies Proceedings of the LANE 2016 VL - Vol. 83 SP - 833 EP - 838 ER - TY - JOUR A1 - Kessler, Julia A1 - Balc, Nicolae A1 - Gebhardt, Andreas A1 - Abbas, Karim T1 - Basic Research on Lattice Structures Focused on the Tensile Strength JF - Applied Mechanics and Materials Y1 - 2015 U6 - http://dx.doi.org/10.4028/www.scientific.net/AMM.808.193 SN - 1662-7482 N1 - MTeM ; October 14-16, 2015, Cluj-Napoca, Romania VL - Vol. 808 SP - 193 EP - 198 PB - Trans Tech Publications CY - Bäch ER - TY - CHAP A1 - Kessler, Julia A1 - Balc, Nicolae A1 - Gebhardt, Andreas A1 - Abbas, Karim T1 - Basic research on lattice structures focused on the reliance of the cross sectional area and additional coatings T2 - The 4th International Conference on Computing and Solutions in Manufacturing Engineering 2016 – CoSME’16 Y1 - 2017 U6 - http://dx.doi.org/10.1051/matecconf/20179403008 N1 - MATEC Web Conf. Vol 94, 2017, 03008 MATEC Web of Conferences 94, 03008 (2017) ET - Vol. 94 ER - TY - CHAP A1 - Kilic, S. A. A1 - Raatschen, Hans-Jürgen A1 - Astaneh-Asl, A. A1 - Apaydin, N. M. T1 - Finite element modeling of the Fatih Sultan Mehmet Suspension Bridge T2 - Multi-Span Large Bridges - Proceedings of the International Conference on Multi-Span Large Bridges Y1 - 2015 SN - 9781138027572 SP - 1169 EP - 1173 PB - CRC Press CY - Leiden ER - TY - JOUR A1 - Kilic, S. A. A1 - Raatschen, Hans-Jürgen A1 - Körfgen, B. A1 - Apaydin, N. M. A1 - Astaneh-Asl, A. T1 - FE Model of the Fatih Sultan Mehmet Suspension Bridge Using Thin Shell Finite Elements JF - Arabian Journal for Science and Engineering N2 - This paper presents the results of an eigenvalue analysis of the Fatih Sultan Mehmet Bridge. A high-resolution finite element model was created directly from the available design documents. All physical properties of the structural components were included in detail, so no calibration to the measured data was necessary. The deck and towers were modeled with shell elements. A nonlinear static analysis was performed before the eigenvalue calculation. The calculated natural frequencies and corresponding mode shapes showed good agreement with the available measured ambient vibration data. The calculation of the effective modal mass showed that nine modes had single contributions higher than 5 % of the total mass. They were in a frequency range up to 1.2 Hz. The comparison of the results for the torsional modes especially demonstrated the advantage of using thin shell finite elements over the beam modeling approach. KW - Suspension bridge KW - 3D nonlinear finite element model KW - Thin shell finite elements KW - Natural frequency KW - Effective modal mass Y1 - 2017 U6 - http://dx.doi.org/10.1007/s13369-016-2316-y SN - 2191-4281 VL - 42 IS - 3 SP - 1103 EP - 1116 PB - Springer Nature ER - TY - CHAP A1 - Kleine, Harald A1 - Kallweit, Stephan A1 - Michaux, Frank A1 - Havermann, Marc A1 - Olivier, Herbert T1 - PIV Measurement of Shock Wave Diffraction T2 - 18th International Symposium on Applications of Laser Techniques to Fluid Mechanics, 2016, Lissabon Y1 - 2016 SP - 1 EP - 14 ER - TY - BOOK A1 - Klocke, Martina T1 - Einfluß des Gefüges von Edelkorundschleifscheiben auf ihre Werkstoffkennwerte und das Schleifverhalten Y1 - 1986 SN - 3446148299 N1 - Produktionstechnik Berlin ; 52 ; Nebent.: Gefüge und Schleifverhalten von Edelkorundschleifscheiben. Techn. Univ., Diss. , Berlin, 1986. PB - Hanser CY - München ER - TY - JOUR A1 - Klocke, Martina T1 - Entwicklung der Feinbearbeitung am Institut für Werkzeugmaschinen und Fertigungstechnik der Technischen Universität Berlin / Klocke, M.; Klocke, F. ; Stark, C. JF - Zeitschrift für wirtschaftliche Fertigung: ZwF. 83 (1988), H. 10 Y1 - 1988 SN - 0044-3743 SP - 521 EP - 529 ER - TY - BOOK A1 - Klocke, Martina T1 - CIM, Bedeutung für die Weiterbildung in Klein- und Mittelbetrieben : [Bericht über den EUROTECNET-Workshop "CIM - Bedeutung für die Weiterbildung in Klein- und Mittelbetrieben" vom 16. bis 17. Oktober 1991 in Elmshorn (BR Deutschland)] / [Bericht erstattet von Martina Klocke] Y1 - 1992 N1 - Workshop "CIM - Bedeutung für die Weiterbildung in Klein- und Mittelbetrieben" <1991, Elmshorn> PB - EUROTECNET CY - Brüssel ER - TY - JOUR A1 - Klocke, Martina T1 - Die Situation von Ingenieurinnen in Europa - ein Ländervergleich JF - Neue Impulse (1995) Y1 - 1995 SN - 0943-4240 SP - 7 EP - 16 ER - TY - JOUR A1 - Klocke, Martina T1 - Angebotsstrukturen und Kosten bzw. Wirtschaftlichkeit von Bildungsangeboten JF - Entwicklung und Umsetzung regionaler Qualifizierungsstrategien : Reader zum Workshop am 21.02.1994 in Berlin / Hrsg.: Bundesinstitut für Berufsbildung. Christel Alt ... (Hrsg.) Y1 - 1995 SN - 3-7639-0531-6 N1 - Bundesinstitut für Berufsbildung Tagungen und Expertengespräche zur beruflichen Bildung ; 24 SP - 37 EP - 40 PB - Bertelsmann CY - Bielefeld ER - TY - JOUR A1 - Klocke, Martina T1 - Lernfabrik - externer Ort für Personalentwicklung JF - Entwicklung und Umsetzung regionaler Qualifizierungsstrategien : Reader zum Workshop am 21.02.1994 in Berlin / Hrsg.: Bundesinstitut für Berufsbildung. Christel Alt ... (Hrsg.) Y1 - 1995 SN - 3-7639-0531-6 N1 - Bundesinstitut für Berufsbildung Tagungen und Expertengespräche zur beruflichen Bildung ; 24 ; in der Vorlage fälschlicherweise: Marina Klocke SP - 89 EP - 94 PB - Bertelsmann CY - Bielefeld ER - TY - JOUR A1 - Klocke, Martina T1 - Study Units in the CIM-Oriented Study Factory JF - Qualification for Computer-Integrated Manufacturing. Hrsg.: Felix Rauner Y1 - 1995 SN - 3-540-19971-3 SP - 38 EP - 51 PB - Springer CY - Berlin [u.a.] ER - TY - JOUR A1 - Klocke, Martina T1 - Kiel – eine Fachhochschule macht Stadtteilarbeit Y1 - 2000 N1 - http://www.zukunft-der-regionen.de (aufgerufen am 17.07.2006) CY - Kiel ER - TY - JOUR A1 - Klocke, Martina T1 - Die Situation von Ingenieurinnen in Europa - ein Ländervergleich JF - Berufsziel: Ingenieurin : Aufbruch in die/der Technik / hrsg. von Renate Kosuch Y1 - 1996 SN - 3-89271-645-5 SP - 26 EP - 38 PB - Deutscher Studien-Verl. CY - Weinheim ER - TY - JOUR A1 - Klocke, Martina T1 - Lernfabrik - externer Ort für Personalentwicklung? JF - Lean-Management : Potentiale und Erfolge ; mit den Referaten zur 19. Deutschen Industrial-Engeneering-Fachtagung am 2. und 3. Dezember 1993 und weiteren Beiträgen zum angewandten Industrial engineering / REFA-IE Y1 - 1993 N1 - Deutsche Industrial-Engineering-Fachtagung, <19, 1993, Darmstadt> Deutsches IE-Jahrbuch 1993 SP - 6/1 EP - 6/15 CY - Darmstadt ER - TY - JOUR A1 - Klocke, Martina T1 - Entwicklung von modularen Lerneinheiten in der CIM-orientierten Lernfabrik JF - CIM, Bedeutung für die Weiterbildung in Klein- und Mittelbetrieben : [Bericht über den EUROTECNET-Workshop "CIM - Bedeutung für die Weiterbildung in Klein- und Mittelbetrieben" vom 16. bis 17. Oktober 1991 in Elmshorn (BR Deutschland)] / [Bericht erstattet von Martina Klocke] Y1 - 1992 N1 - Workshop "CIM - Bedeutung für die Weiterbildung in Klein- und Mittelbetrieben" <1991, Elmshorn> SP - 49 EP - 60 PB - EUROTECNET CY - Brüssel ER -