TY - JOUR A1 - Braun, Sebastian A1 - Cheng, Chi-Tsun A1 - Dowey, Steve A1 - Wollert, Jörg T1 - Performance evaluation of skill-based order-assignment in production environments with multi-agent systems JF - IEEE Journal of Emerging and Selected Topics in Industrial Electronics N2 - The fourth industrial revolution introduces disruptive technologies to production environments. One of these technologies are multi-agent systems (MASs), where agents virtualize machines. However, the agent's actual performances in production environments can hardly be estimated as most research has been focusing on isolated projects and specific scenarios. We address this gap by implementing a highly connected and configurable reference model with quantifiable key performance indicators (KPIs) for production scheduling and routing in single-piece workflows. Furthermore, we propose an algorithm to optimize the search of extrema in highly connected distributed systems. The benefits, limits, and drawbacks of MASs and their performances are evaluated extensively by event-based simulations against the introduced model, which acts as a benchmark. Even though the performance of the proposed MAS is, on average, slightly lower than the reference system, the increased flexibility allows it to find new solutions and deliver improved factory-planning outcomes. Our MAS shows an emerging behavior by using flexible production techniques to correct errors and compensate for bottlenecks. This increased flexibility offers substantial improvement potential. The general model in this paper allows the transfer of the results to estimate real systems or other models. KW - cyber-physical production systems KW - event-based simulation KW - multi-agent systems KW - digital factory KW - industrial agents Y1 - 2021 U6 - http://dx.doi.org/10.1109/JESTIE.2021.3108524 SN - 2687-9735 IS - Early Access PB - IEEE CY - New York ER - TY - CHAP A1 - Braun, Sebastian A1 - Cheng, Chi-Tsun A1 - Lai, Chow Yin A1 - Wollert, Jörg T1 - Microservice Architecture for Automation - Realization by the example of a model-factory’s manufacturing execution system T2 - Proceedings of the 23rd World Multi-Conference on Systemics, Cybernetics and Informatics: WMSCI 2019 Y1 - 2019 SP - 33 EP - 37 ER - TY - JOUR A1 - Bucur, Alexandru A1 - Lazarescu, Lucian A1 - Pop, Grigore Marian A1 - Achimas, Gheorghe A1 - Gebhardt, Andreas T1 - Tribological performance of biodegradable lubricants under different surface roughness of tools JF - Academic Journal of Manufacturing Engineering Y1 - 2019 SN - 1583-7904 VL - 17 IS - 1 SP - 172 EP - 178 ER - TY - CHAP A1 - Buda, Aurel A1 - Jozenfini, B. A1 - Wollert, Jörg T1 - Mobile ad-hoc Network for home automation based on ZigBee application framework T2 - 1st European ZigBee Developer's Conference : June 18 - 20, 2007, Munich, Germany Y1 - 2007 SP - 1 EP - 5 PB - Design & Elektronik CY - Poing ER - TY - CHAP A1 - Buda, Aurel A1 - Schürmann, Volker A1 - Wollert, Jörg T1 - Wireless technologies in factory automation T2 - Factory automation / ed. by Javier Silvestre-Blanes Y1 - 2010 SN - 978-953-7619-42-8 SP - 29 EP - 50 PB - Intech CY - London ER - TY - CHAP A1 - Buschkühle, Peter A1 - Schürmann, Volker A1 - Wollert, Jörg T1 - Abstraction of wireless communication by a convergence middleware in conjunction with a XML-configuration T2 - Information technology and electrical engineering : devices and systems, materials and technologies for the future ; Ilmenau 07 - 10 September 2009 ; 54. IWK Internationales Wissenschaftliches Kolloquium Y1 - 2009 SN - 978-3-938843-44-4 SP - 95 EP - 96 PB - Techn. Univ. CY - Ilmenau ER - TY - CHAP A1 - Bücking, Henrik A1 - Pfaff, Raphael A1 - Dirksmeier, Roger T1 - Sensor positioning and thermal model for condition monitoring of pressure gas reservoirs in vehicles T2 - Proceedings of the Fourth European Conference of the Prognostics and Health Management Society, Utrecht, Netherlands, 2018 Y1 - 2018 ER - TY - CHAP A1 - Chavez Bermudez, Victor Francisco A1 - Cruz Castanon, Victor Fernando A1 - Ruchay, Marco A1 - Wollert, Jörg ED - Leipzig, Hochschule für Technik, Wirtschaft und Kultur T1 - Rapid prototyping framework for automation applications based on IO-Link T2 - Tagungsband AALE 2022 N2 - The development of protype applications with sensors and actuators in the automation industry requires tools that are independent of manufacturer, and are flexible enough to be modified or extended for any specific requirements. Currently, developing prototypes with industrial sensors and actuators is not straightforward. First of all, the exchange of information depends on the industrial protocol that these devices have. Second, a specific configuration and installation is done based on the hardware that is used, such as automation controllers or industrial gateways. This means that the development for a specific industrial protocol, highly depends on the hardware and the software that vendors provide. In this work we propose a rapid-prototyping framework based on Arduino to solve this problem. For this project we have focused to work with the IO-Link protocol. The framework consists of an Arduino shield that acts as the physical layer, and a software that implements the IO-Link Master protocol. The main advantage of such framework is that an application with industrial devices can be rapid-prototyped with ease as its vendor independent, open-source and can be ported easily to other Arduino compatible boards. In comparison, a typical approach requires proprietary hardware, is not easy to port to another system and is closed-source. KW - Rapid-prototyping KW - Arduino KW - IO-Link KW - Industrial Communication Y1 - 2022 SN - 978-3-910103-00-9 U6 - http://dx.doi.org/10.33968/2022.28 N1 - 18. AALE-Konferenz, Pforzheim, 09.03.-11.03.2022. CY - Leipzig ER - TY - CHAP A1 - Chavez Bermudez, Victor Francisco A1 - Wollert, Jörg T1 - 10BASE-T1L industry 4.0 smart switch for field devices based on IO-Link T2 - 2022 IEEE 18th International Conference on Factory Communication Systems (WFCS) N2 - The recent amendment to the Ethernet physical layer known as the IEEE 802.3cg specification, allows to connect devices up to a distance of one kilometer and delivers a maximum of 60 watts of power over a twisted pair of wires. This new standard, also known as 10BASE-TIL, promises to overcome the limits of current physical layers used for field devices and bring them a step closer to Ethernet-based applications. The main advantage of 10BASE- TIL is that it can deliver power and data over the same line over a long distance, where traditional solutions (e.g., CAN, IO-Link, HART) fall short and cannot match its 10 Mbps bandwidth. Due to its recentness, IOBASE- TIL is still not integrated into field devices and it has been less than two years since silicon manufacturers released the first Ethernet-PHY chips. In this paper, we present a design proposal on how field devices could be integrated into a IOBASE-TIL smart switch that allows plug-and-play connectivity for sensors and actuators and is compliant with the Industry 4.0 vision. Instead of presenting a new field-level protocol for this work, we have decided to adopt the IO-Link specification which already includes a plug-and-play approach with features such as diagnosis and device configuration. The main objective of this work is to explore how field devices could be integrated into 10BASE-TIL Ethernet, its adaption with a well-known protocol, and its integration with Industry 4.0 technologies. KW - 10BASE-T1L KW - Ethernet KW - Field device KW - Sensors KW - IO-Link Y1 - 2022 SN - 978-1-6654-1086-1 SN - 978-1-6654-1087-8 U6 - http://dx.doi.org/10.1109/WFCS53837.2022.9779176 N1 - 2022 IEEE 18th International Conference on Factory Communication Systems (WFCS), 27-29 April 2022, Pavia, Italy- PB - IEEE ER - TY - CHAP A1 - Chavez Bermudez, Victor Francisco A1 - Wollert, Jörg T1 - Gateway for Automation Controllers and Cloud based Voice Recognition Services T2 - KommA, 10. Jahreskolloquium Kommunikation in der Automation Y1 - 2019 SN - 978-3-944722-85-6 SP - 1 EP - 8 PB - Institut für Automation und Kommunikation CY - Magdeburg ER - TY - CHAP A1 - Chavez Bermudez, Victor Francisco A1 - Wollert, Jörg T1 - Arduino based Framework for Rapid Application Development of a Generic IO-Link interface T2 - Kommunikation und Bildverarbeitung in der Automation N2 - The implementation of IO-Link in the automation industry has increased over the years. Its main advantage is it offers a digital point-to-point plugand-play interface for any type of device or application. This simplifies the communication between devices and increases productivity with its different features like self-parametrization and maintenance. However, its complete potential is not always used. The aim of this paper is to create an Arduino based framework for the development of generic IO-Link devices and increase its implementation for rapid prototyping. By generating the IO device description file (IODD) from a graphical user interface, and further customizable options for the device application, the end-user can intuitively develop generic IO-Link devices. The peculiarity of this framework relies on its simplicity and abstraction which allows to implement any sensor functionality and virtually connect any type of device to an IO-Link master. This work consists of the general overview of the framework, the technical background of its development and a proof of concept which demonstrates the workflow for its implementation. Y1 - 2020 SN - 978-3-662-59895-5 SN - 978-3-662-59894-8 U6 - http://dx.doi.org/10.1007/978-3-662-59895-5_2 N1 - Teil der Buchserie "Technologien für die intelligente Automation" (TIA,volume 12) SP - 21 EP - 33 PB - Springer Vieweg CY - Berlin ER - TY - JOUR A1 - Cheng, Chi-Tsun A1 - Wollert, Jörg A1 - Chen, Xi A1 - Fapojuwo, Abraham O. T1 - Guest Editorial : Circuits and Systems for Industry X.0 Applications JF - IEEE Journal on Emerging and Selected Topics in Circuits and Systems Y1 - 2023 U6 - http://dx.doi.org/10.1109/JETCAS.2023.3278843 SN - 2156-3357 (Print) SN - 2156-3365 (Online) VL - 13 SP - 457 EP - 460 PB - IEEE CY - New York ET - 2 ER - TY - CHAP A1 - Chudoba, Rostislav A1 - Konrad, Martin A1 - Schleser, Markus A1 - Meskouris, Konstantin A1 - Reisgen, Uwe ED - Curbach, Manfred T1 - Parametric study of tensile response of TRC specimens reinforced with epoxy-penetrated multi-filament yarns T2 - Textilbeton - Theorie und Praxis : Tagungsband zum 4. Kolloquium zu textilbewehrten Tragwerken (CTRS4) und zur 1. Anwendertagung, Dresden, 3.6.2009 - 5.6.2009 Y1 - 2009 SN - 978-3-86780-122-5 SP - 87 EP - 98 PB - Techn. Univ. CY - Dresden ER - TY - JOUR A1 - Cosma, Cosmin A1 - Kessler, Julia A1 - Gebhardt, Andreas A1 - Campbell, Ian A1 - Balc, Nicolae T1 - Improving the Mechanical Strength of Dental Applications and Lattice Structures SLM Processed JF - Materials N2 - To manufacture custom medical parts or scaffolds with reduced defects and high mechanical characteristics, new research on optimizing the selective laser melting (SLM) parameters are needed. In this work, a biocompatible powder, 316L stainless steel, is characterized to understand the particle size, distribution, shape and flowability. Examination revealed that the 316L particles are smooth, nearly spherical, their mean diameter is 39.09 μm and just 10% of them hold a diameter less than 21.18 μm. SLM parameters under consideration include laser power up to 200 W, 250–1500 mm/s scanning speed, 80 μm hatch spacing, 35 μm layer thickness and a preheated platform. The effect of these on processability is evaluated. More than 100 samples are SLM-manufactured with different process parameters. The tensile results show that is possible to raise the ultimate tensile strength up to 840 MPa, adapting the SLM parameters for a stable processability, avoiding the technological defects caused by residual stress. Correlating with other recent studies on SLM technology, the tensile strength is 20% improved. To validate the SLM parameters and conditions established, complex bioengineering applications such as dental bridges and macro-porous grafts are SLM-processed, demonstrating the potential to manufacture medical products with increased mechanical resistance made of 316L. Y1 - 2020 U6 - http://dx.doi.org/10.3390/ma13040905 SN - 1996-1944 VL - 13 IS - 4 SP - 1 EP - 18 PB - MDPI CY - Basel ER - TY - CHAP A1 - Dannen, Tammo A1 - Schindele, Benedikt A1 - Prümmer, Marcel A1 - Arntz, Kristian A1 - Bergs, Thomas T1 - Methodology for the self-optimizing determination of additive manufacturing process eligibility and optimization potentials in toolmaking T2 - Procedia CIRP N2 - Additive Manufacturing (AM) of metallic workpieces faces a continuously rising technological relevance and market size. Producing complex or highly strained unique workpieces is a significant field of application, making AM highly relevant for tool components. Its successful economic application requires systematic workpiece based decisions and optimizations. Considering geometric and technological requirements as well as the necessary post-processing makes deciding effortful and requires in-depth knowledge. As design is usually adjusted to established manufacturing, associated technological and strategic potentials are often neglected. To embed AM in a future proof industrial environment, software-based self-learning tools are necessary. Integrated into production planning, they enable companies to unlock the potentials of AM efficiently. This paper presents an appropriate methodology for the analysis of process-specific AM-eligibility and optimization potential, added up by concrete optimization proposals. For an integrated workpiece characterization, proven methods are enlarged by tooling-specific figures. The first stage of the approach specifies the model’s initialization. A learning set of tooling components is described using the developed key figure system. Based on this, a set of applicable rules for workpiece-specific result determination is generated through clustering and expert evaluation. Within the following application stage, strategic orientation is quantified and workpieces of interest are described using the developed key figures. Subsequently, the retrieved information is used for automatically generating specific recommendations relying on the generated ruleset of stage one. Finally, actual experiences regarding the recommendations are gathered within stage three. Statistic learning transfers those to the generated ruleset leading to a continuously deepening knowledge base. This process enables a steady improvement in output quality. KW - Additive manufacturing KW - Laser-Powder Bed Fusion KW - L-PBF KW - Binder Jetting KW - Directed Energy Deposition Y1 - 2022 U6 - http://dx.doi.org/10.1016/j.procir.2022.05.188 SN - 2212-8271 N1 - 55th CIRP Conference on Manufacturing Systems VL - 107 SP - 1539 EP - 1544 PB - Elsevier CY - Amsterdam ER - TY - JOUR A1 - Dilthey, Ulrich A1 - Brandenburg, Annette A1 - Schleser, Markus T1 - Dispensing and application of unfilled adhesives in the micro range JF - Welding and cutting. 3 (2004), H. 4 Y1 - 2004 SN - 1612-3433 SP - 250 EP - 254 ER - TY - CHAP A1 - Dilthey, Ulrich A1 - Mund, F. A1 - Raupach, Michael A1 - Schleser, Markus A1 - Walk-Lauffer, Bernd T1 - Improvement of textile reinforced concrete by polymer additives T2 - ICPIC '04 : 11th International Congress on Polymers in Concrete : 2nd-4th June, 2004 at BAM, Berlin, Germany : proceedings / ed. by M. Maultzsch Y1 - 2004 SN - 3-00-013706-8 SP - 469 EP - 476 PB - BAM CY - Berlin ER - TY - CHAP A1 - Dilthey, Ulrich A1 - Schleser, Markus ED - Barroso de Aguiar, Jose ED - Jalali, Said ED - Camoes, Aires ED - Ferrera, Rui Miguel T1 - Composite improvement of textile reinforced concrete by polymeric impregnation of the textiles T2 - International Symposium Polymers in Concrete : proceedings of ISPIC 2006, 2-4 April 2006 - University of Minho - Guimarães, Portugal Y1 - 2006 SN - 972-99179-1-4 SP - 185 EP - 192 PB - Universidade do Minho, Departamento de Engenharia Civil CY - Guimarães ER - TY - CHAP A1 - Dilthey, Ulrich A1 - Schleser, Markus A1 - Chudoba, Rostislav A1 - Konrad, Martin ED - Triantafillou, T. C. T1 - Experimental investigation and micro-mechanical simulaltion of concrete reinforced with epoxy impregnated fabrics T2 - Fibre-reinforced polymer reinforcement for concrete structures : proceedings of the 8th international conference : Patras, Greece, July 16- 18, 2007 Y1 - 2007 SN - 9608969107 SP - 456 EP - 457 PB - Univ. CY - Patras ER - TY - JOUR A1 - Dilthey, Ulrich A1 - Schleser, Markus A1 - Feldmann, Martin A1 - Pak, Daniel A1 - Geßler, Achim T1 - Investigation of punctiform, plane and hybrid joints of textile-reinforced concrete parts JF - Cement and concrete composites Y1 - 2008 SN - 0958-9465 VL - Vol. 30 IS - iss. 2 SP - 82 EP - 87 ER - TY - CHAP A1 - Dilthey, Ulrich A1 - Schleser, Markus A1 - Hegger, Josef A1 - Voss, Stefan ED - Reinhardt, Hans W. T1 - Load-bearing behaviour of polymer-impregnated textiles in concrete T2 - Fifth International Workshop on High Performance Fiber Reinforced Cement Composites (HPFRCC 5) : Mainz, July 10 - 13, 2007. (RILEM proceedings. 53) Y1 - 2007 SN - 978-2-35158-046-2 SP - 183 EP - 192 PB - RILEM Publ. CY - Bagneux ER - TY - CHAP A1 - Dilthey, Ulrich A1 - Schleser, Markus A1 - Möller, M. A1 - Weichhold, O. ED - Hegger, Josef T1 - Application of polymers in textile reinforced concrete : from the interface to construction elements T2 - Textile reinforced concrete : proceedings of the 1. International RILEM Conference, held at the RWTH Aachen, September 6/7, 2006. (RILEM proceedings ; 50) Y1 - 2006 SN - 2-912143-97-7 SP - 55 EP - 64 PB - RILEM Publ. CY - Bagneux ER - TY - CHAP A1 - Dilthey, Ulrich A1 - Schleser, Markus A1 - Puterman, Moshe T1 - Investigation and improvement of concrete reinforced with epoxy impregnated fabrics T2 - Proceedings / 12th International Congress Polymers in Concrete, ICPIC 07, chuncheon, Korea, Sept. 26. - 28., 2007 Y1 - 2007 SN - 978-89-9600450-9 SP - 725 EP - 733 PB - Kangwoon National Univ. CY - Chancheon ER - TY - JOUR A1 - Dues, M. A1 - Gebhardt, Andreas A1 - Kallweit, Stephan A1 - Scheffler, T. A1 - Siekmann, H. A1 - Uchiyama, T. T1 - Flow Visualization in a Cavitating Flow JF - Proceedings of the German-Japanese Symposium on Multi-Phase Flow : Karlsruhe, Germany, August 23 - 25, 1994 / comp. by U. Müller ... Y1 - 1994 N1 - German Japanese Symposium on Multi-Phase Flow <1994, Karlsruhe> ; Kernforschungszentrum Karlsruhe ; 5389 SP - 391 EP - 402 PB - Kernforschungszentrum Karlsruhe CY - Karlsruhe ER - TY - CHAP A1 - Eichler, Fabian A1 - Skupin, Marco A1 - Thurn, Laura A1 - Kasch, Susanne A1 - Schmidt, Thomas T1 - Operating limits for beam melting of glass materials T2 - Modern Technologies in Manufacturing (MTeM 2019) N2 - Laser-based Additive Manufacturing (AM) processes for the use of metals out of the powder bed have been investigated profusely and are prevalent in industry. Although there is a broad field of application, Laser Powder Bed Fusion (LPBF), also known as Selective Laser Melting (SLM) of glass is not fully developed yet. The material properties of glass are significantly different from the investigated metallic material for LPBF so far. As such, the process cannot be transferred, and the parameter limits and the process sequence must be redefined for glass. Starting with the characterization of glass powders, a parameter field is initially confined to investigate the process parameter of different glass powder using LPBFprocess. A feasibility study is carried out to process borosilicate glass powder. The effects of process parameters on the dimensional accuracy of fabricated parts out of borosilicate and hints for the post-processing are analysed and presented in this paper. Y1 - 2019 U6 - http://dx.doi.org/10.1051/matecconf/201929901004 N1 - MATEC Web of Conferences 299; MTeM 2019 VL - 299 IS - Article 01004 ER - TY - BOOK A1 - Engeln-Müllges, Gisela A1 - Uhlig, Frank T1 - Numeric Algorithms with Fortran Y1 - 1996 SN - 3-540-60529-0 PB - Springer CY - Berlin [u.a.] ER - TY - BOOK A1 - Engeln-Müllges, Gisela A1 - Uhlig, Frank T1 - Numerical algorithms with C Y1 - 1996 SN - 3-540-60530-0 PB - Springer CY - Berlin [u.a.] ER - TY - CHAP A1 - Engemann, Heiko A1 - Badri, Sriram A1 - Wenning, Marius A1 - Kallweit, Stephan T1 - Implementation of an Autonomous Tool Trolley in a Production Line T2 - Advances in Service and Industrial Robotics. RAAD 2019. Advances in Intelligent Systems and Computing, vol 980 Y1 - 2019 SN - 978-3-030-19648-6 U6 - http://dx.doi.org/10.1007/978-3-030-19648-6_14 SP - 117 EP - 125 PB - Springer CY - Cham ER - TY - JOUR A1 - Engemann, Heiko A1 - Cönen, Patrick A1 - Dawar, Harshal A1 - Du, Shengzhi A1 - Kallweit, Stephan T1 - A robot-assisted large-scale inspection of wind turbine blades in manufacturing using an autonomous mobile manipulator JF - Applied Sciences N2 - Wind energy represents the dominant share of renewable energies. The rotor blades of a wind turbine are typically made from composite material, which withstands high forces during rotation. The huge dimensions of the rotor blades complicate the inspection processes in manufacturing. The automation of inspection processes has a great potential to increase the overall productivity and to create a consistent reliable database for each individual rotor blade. The focus of this paper is set on the process of rotor blade inspection automation by utilizing an autonomous mobile manipulator. The main innovations include a novel path planning strategy for zone-based navigation, which enables an intuitive right-hand or left-hand driving behavior in a shared human–robot workspace. In addition, we introduce a new method for surface orthogonal motion planning in connection with large-scale structures. An overall execution strategy controls the navigation and manipulation processes of the long-running inspection task. The implemented concepts are evaluated in simulation and applied in a real-use case including the tip of a rotor blade form. KW - mobile manipulation KW - large-scale inspection KW - wind turbine production KW - autonomous navigation KW - surface-orthogonal path planning Y1 - 2021 U6 - http://dx.doi.org/10.3390/app11199271 SN - 2076-3417 N1 - Belongs to the Special Issue "Advances in Industrial Robotics and Intelligent Systems" VL - 11 IS - 19 SP - 1 EP - 22 PB - MDPI CY - Basel ER - TY - JOUR A1 - Engemann, Heiko A1 - Du, Shengzhi A1 - Kallweit, Stephan A1 - Cönen, Patrick A1 - Dawar, Harshal T1 - OMNIVIL - an autonomous mobile manipulator for flexible production JF - Sensors Y1 - 2020 SN - 1424-8220 U6 - http://dx.doi.org/10.3390/s20247249 N1 - Special issue: Sensor Networks Applications in Robotics and Mobile Systems VL - 20 IS - 24, art. no. 7249 SP - 1 EP - 30 PB - MDPI CY - Basel ER - TY - CHAP A1 - Engemann, Heiko A1 - Du, Shengzhi A1 - Kallweit, Stephan A1 - Ning, Chuanfang A1 - Anwar, Saqib T1 - AutoSynPose: Automatic Generation of Synthetic Datasets for 6D Object Pose Estimation T2 - Machine Learning and Artificial Intelligence. Proceedings of MLIS 2020 N2 - We present an automated pipeline for the generation of synthetic datasets for six-dimension (6D) object pose estimation. Therefore, a completely automated generation process based on predefined settings is developed, which enables the user to create large datasets with a minimum of interaction and which is feasible for applications with a high object variance. The pipeline is based on the Unreal 4 (UE4) game engine and provides a high variation for domain randomization, such as object appearance, ambient lighting, camera-object transformation and distractor density. In addition to the object pose and bounding box, the metadata includes all randomization parameters, which enables further studies on randomization parameter tuning. The developed workflow is adaptable to other 3D objects and UE4 environments. An exemplary dataset is provided including five objects of the Yale-CMU-Berkeley (YCB) object set. The datasets consist of 6 million subsegments using 97 rendering locations in 12 different UE4 environments. Each dataset subsegment includes one RGB image, one depth image and one class segmentation image at pixel-level. Y1 - 2020 SN - 978-1-64368-137-5 U6 - http://dx.doi.org/10.3233/FAIA200770 N1 - Frontiers in Artificial Intelligence and Applications. Vol 332 SP - 89 EP - 97 PB - IOS Press CY - Amsterdam ER - TY - CHAP A1 - Engemann, Heiko A1 - Wiesen, Patrick A1 - Kallweit, Stephan A1 - Deshpande, Harshavardhan A1 - Schleupen, Josef T1 - Autonomous mobile manipulation using ROS T2 - Advances in Service and Industrial Robotics Y1 - 2018 SN - 978-3-319-61276-8 U6 - http://dx.doi.org/10.1007/978-3-319-61276-8_43 N1 - International Conference on Robotics in Alpe-Adria Danube Region RAAD 2017; Mechanisms and Machince Science book series, Vol 49. SP - 389 EP - 401 PB - Springer CY - Cham ER - TY - JOUR A1 - Enning, Manfred A1 - Baier, M. T1 - Energetic and operational use of FlexCargoRail freight wagons in the single wagon load traffic / Baier, M. ; Enning, M. JF - Towards zero emission : EVS 24, the 24th International Battery, Hybrid and Fuel Cell Electric Vehicle Symposium & Exhibition, Stavanger, Norway, May 13 - 16, 2009 ; symposium proceedings / organised by AVERE ... Robert Stüssi [Hrsg.] Y1 - 2009 N1 - European Association of Electric Road Vehicles ; EVS ; (24 : ; 2009.05.13-16 : ; Stavanger) CY - Stavanger ER - TY - JOUR A1 - Enning, Manfred A1 - Bernhard, S. A1 - Rake, H. T1 - Automation of a laboratory plant for direct casting of thin steel strips / Bernhard, S. ; Enning, M. ; Rake, H. JF - Control Engineering Practice. 2 (1994), H. 6 Y1 - 1994 SN - 0967-0661 SP - 961 EP - 967 ER - TY - JOUR A1 - Enning, Manfred A1 - Hücker, Jan A1 - Jenayeh, Imad A1 - Rake, Heinrich T1 - A Parametric Identification Scheme for a Self-tuning Industrial Compact Controller - INTERKAMA 1999 / Hucker, Jan ; Jenayeh, Imad ; Enning, Manfred ; Rake, Heinrich Y1 - 1999 N1 - ISA TP99UN139 ; Proceedings ISA-Tech Conference, Düsseldorf 1999 ER - TY - JOUR A1 - Enning, Manfred A1 - Jenayeh, I. A1 - Müller, C. A1 - Kositza, N. T1 - Mechatronics in automating shunting processes in marshalling yards / Jenayeh, I. ; Müller, C.; Kositza, N. ; Enning, M. ; Rake, H. JF - Mechatronics '98 : proceedings of the 6th UK Mechatronics Forum International Conference, Skövde, Sweden, 9-11 September 1998 Y1 - 1998 SN - 0-08-043339-1 N1 - UK Mechatronics Forum International Conference (6 : 1998 : Skövde) PB - Pergamon CY - Amsterdam ER - TY - JOUR A1 - Enning, Manfred A1 - Jenayeh, I. A1 - Müller, C. A1 - Kositza, N. T1 - A New Approach for Automating Shunting Processes in Marshalling Yards / Jenayeh, I.; Müller, C. ; Kositza, N. ; Enning, M. ; Rake, H. JF - Computational Engineering in Systems Applications : 2nd IMACS International Multiconference CESA'98; [abstracts; Nabeul-Hammamet, Tunisia, April 1 - 4, 1998] / ed. by Pierre Borne Y1 - 1998 SP - 338 EP - 343 PB - UCIS CY - Villeneuve d'Ascq ER - TY - JOUR A1 - Enning, Manfred A1 - Jenayeh, I. A1 - Müller, C. A1 - Rake, Heinrich T1 - Development and realization of a manipulator for automatic decoupling of freight cars in marshalling yards / Jenayeh, I. ; Müller, C. ; Enning, Manfred ; Rake, Heinrich ; Peter, J. Y1 - 1997 N1 - World Congress on Railway Research, Florenz, 16.-19.11.1997, 1997 ER - TY - JOUR A1 - Enning, Manfred A1 - Mann, S. A1 - Bollig, A. A1 - Kaierle, S. T1 - Autonomous Production Cell for Laser Beam Welding / Mann S. ; Bollig, A. ; Kaierle, S. ; Abel, D. ; Poprawe, R. Y1 - 2003 SN - 0912035757 N1 - ICALEO 2003, Florida ; Laser Materials Processing Conference ; (2003, Jacksonville, Fla.) ; ICALEO ; (22, 2003, Jacksonville, Fla.) PB - LIA CY - Orlando, Fla ER - TY - JOUR A1 - Enning, Manfred A1 - Stützle, Thorsten A1 - Viereck, Uwe A1 - Stribersky, Anton T1 - Creepage control for use in wheelslide protection systems / Stützle, Thorsten ; Viereck, Uwe ; Stribersky, Anton ; Rulka, Wolfgang ; Enning, Manfred ; Abel, Dirk JF - Control in transportation systems : proceedings of the 11th IFAC symposium on control in transportation systems (CTS 2006), August 29-31, 2006, Delft, the Netherlands / International Federation of Automatic Control Y1 - 2006 SN - 0742-5953 ER - TY - JOUR A1 - Enning, Manfred A1 - Zambou, N. A1 - Abel, D. T1 - Longitudinal Control of Following Vehicles within Platoon : A Model-Based Predictive Approach / Zambou, N. ; Enning, M. ; Abel, D. JF - Advances in automotive control 2004 : a proceedings volume from the IFAC symposium, Salerno, Italy, 19 - 23 April 2004 / ed. C. Pianese Y1 - 2005 SN - 0080442501 N1 - International Federation of Automatic Control ; Symposium on Advances in Automotive Control ; (4, 2004, Salerno) SP - 733 EP - 738 PB - Elsevier CY - Oxford ER - TY - JOUR A1 - Enning, Manfred A1 - Zambou, Nathan A1 - Abel, Dirk T1 - Nonlinear spacing control of following vehicles within platoon a controlled lagrangian approach / Zambou, Nathan ; Enning, Manfred ; Abel, Dirk JF - NOLCOS, IFAC Symposium on Nonlinear Control Systems Y1 - 2004 N1 - NOLCOS, 2004, IFAC Symposium on Nonlinear Control Systems, 6th, Stuttgart, DE, 2004-09-01 - 2004-09-03 SP - 1211 EP - 1216 ER - TY - CHAP A1 - Evans, Benjamin A1 - Braun, Sebastian A1 - Ulmer, Jessica A1 - Wollert, Jörg T1 - AAS implementations - current problems and solutions T2 - 20th International Conference on Mechatronics - Mechatronika (ME) N2 - The fourth industrial revolution presents a multitude of challenges for industries, one of which being the increased flexibility required of manufacturing lines as a result of increased consumer demand for individualised products. One solution to tackle this challenge is the digital twin, more specifically the standardised model of a digital twin also known as the asset administration shell. The standardisation of an industry wide communications tool is a critical step in enabling inter-company operations. This paper discusses the current state of asset administration shells, the frameworks used to host them and their problems that need to be addressed. To tackle these issues, we propose an event-based server capable of drastically reducing response times between assets and asset administration shells and a multi-agent system used for the orchestration and deployment of the shells in the field. KW - Industry 4.0 KW - Multi-agent Systems KW - Digital Twin KW - Asset Administration Shell Y1 - 2022 SN - 978-1-6654-1040-3 U6 - http://dx.doi.org/10.1109/ME54704.2022.9982933 PB - IEEE ER - TY - CHAP A1 - Fateri, Miranda A1 - Gebhardt, Andreas T1 - Jewelry fabrication via selective laser melting of glass T2 - ASME 2014 12th Biennial Conference on Engineering Systems Design and Analysis Volume 1: Applied Mechanics; Automotive Systems; Biomedical Biotechnology Engineering; Computational Mechanics; Design; Digital Manufacturing; Education; Marine and Aerospace Applications N2 - Selective Laser Melting (SLM) is one of the Additive Manufacturing (AM) technologies applicable for producing complex geometries which are typically expensive or difficult to fabricate using conventional methods. This process has been extensively investigated experimentally for various metals and the fabrication process parameters have been established for different applications; however, fabricating 3D glass objects using SLM technology has remained a challenge so far although it could have many applications. This paper presents a summery on various experimental evaluations of a material database incorporating the build parameters of glass powder using the SLM process for jewelry applications. Y1 - 2014 SN - 978-0-7918-4583-7 U6 - http://dx.doi.org/10.1115/ESDA2014-20380 SP - V001T06A005 ER - TY - JOUR A1 - Fateri, Miranda A1 - Gebhardt, Andreas T1 - Selective Laser Melting of Soda-Lime Glass Powder JF - International Journal of Applied Ceramic Technology Y1 - 2015 U6 - http://dx.doi.org/10.1111/ijac.12338 SN - 1744-7402 VL - 12 IS - 1 SP - 53 EP - 61 PB - Wiley-Blackwell CY - Oxford ER - TY - JOUR A1 - Fateri, Miranda A1 - Gebhardt, Andreas T1 - Process Parameters Development of Selective Laser Melting of Lunar Regolith for On-Site Manufacturing Applications JF - International Journal of Applied Ceramic Technology Y1 - 2015 SN - 1744-7402 U6 - http://dx.doi.org/10.1111/ijac.12326 VL - 12 IS - 1 SP - 46 EP - 52 PB - Wiley-Blackwell CY - Oxford ER - TY - JOUR A1 - Fateri, Miranda A1 - Gebhardt, Andreas T1 - Additive manufactured mechanical disentanglement lock JF - RTejournal - Forum für Rapid Technologie Y1 - 2015 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:0009-2-42147 SN - 1614-0923 VL - 12 PB - Fachhochschule Aachen CY - Aachen ER - TY - CHAP A1 - Fateri, Miranda A1 - Gebhardt, Andreas T1 - Introduction to Additive Manufacturing T2 - 3D Printing of Optical Components N2 - Additive manufacturing (AM) works by creating objects layer by layer in a manner similar to a 2D printer with the “printed” layers stacked on top of each other. The layer-wise manufacturing nature of AM enables fabrication of freeform geometries which cannot be fabricated using conventional manufacturing methods as a one part. Depending on how each layer is created and bonded to the adjacent layers, different AM methods have been developed. In this chapter, the basic terms, common materials, and different methods of AM are described, and their potential applications are discussed. KW - Additive manufacturing KW - 3D printing KW - Digital manufacturing KW - Rapid prototyping KW - Rapid manufacturing Y1 - 2020 SN - 978-3-030-58960-8 U6 - http://dx.doi.org/10.1007/978-3-030-58960-8_1 SP - 1 EP - 22 PB - Springer CY - Cham ER - TY - CHAP A1 - Fateri, Miranda A1 - Gebhardt, Andreas A1 - Gabrielli, Roland Antonius A1 - Herdrich, Georg A1 - Fasoulas, Stefanos A1 - Großmann, Agnes A1 - Schnauffer, Peter A1 - Middendorf, Peter T1 - Additive Manufacturing of Lunar Regolith for Extra-terrestrial Industry Plant T2 - International Symposium on Space Technology and Science (ICTS). July 2015, Kobe, Japan Y1 - 2015 ER - TY - CHAP A1 - Fateri, Miranda A1 - Gebhardt, Andreas A1 - Khosravi, Maziar T1 - Experimental investigation of selective laser melting of lunar regolith for in-situ applications T2 - ASME 2013 International Mechanical Engineering Congress and Exposition : San Diego, California, USA, November 15–21, 2013. Vol. 2A: Advanced manufacturing Y1 - 2013 SN - 978-0-7918-5618-5 SP - V02AT02A008 PB - ASME ER -