TY - JOUR A1 - Kilic, S. A. A1 - Raatschen, Hans-Jürgen A1 - Körfgen, B. A1 - Apaydin, N. M. A1 - Astaneh-Asl, A. T1 - FE Model of the Fatih Sultan Mehmet Suspension Bridge Using Thin Shell Finite Elements JF - Arabian Journal for Science and Engineering N2 - This paper presents the results of an eigenvalue analysis of the Fatih Sultan Mehmet Bridge. A high-resolution finite element model was created directly from the available design documents. All physical properties of the structural components were included in detail, so no calibration to the measured data was necessary. The deck and towers were modeled with shell elements. A nonlinear static analysis was performed before the eigenvalue calculation. The calculated natural frequencies and corresponding mode shapes showed good agreement with the available measured ambient vibration data. The calculation of the effective modal mass showed that nine modes had single contributions higher than 5 % of the total mass. They were in a frequency range up to 1.2 Hz. The comparison of the results for the torsional modes especially demonstrated the advantage of using thin shell finite elements over the beam modeling approach. KW - Suspension bridge KW - 3D nonlinear finite element model KW - Thin shell finite elements KW - Natural frequency KW - Effective modal mass Y1 - 2017 U6 - http://dx.doi.org/10.1007/s13369-016-2316-y SN - 2191-4281 VL - 42 IS - 3 SP - 1103 EP - 1116 PB - Springer Nature ER - TY - JOUR A1 - Kessler, Julia A1 - Balc, Nicolae A1 - Gebhardt, Andreas A1 - Abbas, Karim T1 - Basic Research on Lattice Structures Focused on the Tensile Strength JF - Applied Mechanics and Materials Y1 - 2015 U6 - http://dx.doi.org/10.4028/www.scientific.net/AMM.808.193 SN - 1662-7482 N1 - MTeM ; October 14-16, 2015, Cluj-Napoca, Romania VL - Vol. 808 SP - 193 EP - 198 PB - Trans Tech Publications CY - Bäch ER - TY - JOUR A1 - Kasch, Susanne A1 - Schmidt, Thomas A1 - Jahn, Simon A1 - Eichler, Fabian A1 - Thurn, Laura A1 - Bremen, Sebastian T1 - Lösungsansätze und Verfahrenskonzepte zum Laserstrahlschmelzen von Glas JF - Schweissen und Schneiden Y1 - 2021 SN - 0036-7184 VL - 73 IS - Heft 1-2 SP - 32 EP - 39 PB - DVS Verlag CY - Düsseldorf ER - TY - JOUR A1 - Kampker, Achim A1 - Schleser, Markus A1 - Triebs, Johannes A1 - Berg, Alexander-Karl A1 - Hansen, Jan Ole A1 - Fiedler, Falko T1 - Bauteilintegrierte Vorrichtungsfunktionen im Karosseriebau : Aktuelle Ergebnisse im Forschungsprojekt ProeK JF - ZWF Zeitschrift für wirtschaftlichen Fabrikbetrieb N2 - Das Forschungsprojekt Produktionseffizienz in der Kleinserie (ProeK) erarbeitet kostengünstige und effiziente Lösungsansätze für Prozessketten im Zukunftsfeld der Elektromobilität. Das Teilprojekt Karosserie setzt diese Zielsetzung durch innovative und praxisorientierte Produkt- und Prozesskonzepte mit neuartigen bauteilintegrierten Vorrichtungsfunktionen (BiV) um. Im Teilprojekt Außenhaut sollen Toleranzen adaptiv durch Anpassungen der Prozessparameter sowie Bauteilmanipulation kompensiert werden. Y1 - 2018 U6 - http://dx.doi.org/10.3139/104.112012 SN - 0947-0085 VL - 113 IS - 11 SP - 767 EP - 770 PB - De Gruyter CY - Berlin ER - TY - JOUR A1 - Kallweit, Stephan A1 - Willert, Chris A1 - Dues, Michael A1 - Müller, Ulrich T1 - PIV for Volume Flow Metering / Kallweit, Stephan ; Willert, Chris ; Dues, Michael ; Müller, Ulrich ; Lederer, Thomas Y1 - 2008 N1 - 14th International Symposium on Applications of Laser Techniques to Fluid Mechanics, 2008-07-07 - 2008-07-10, Lisbon (Portugal) SP - 6 S. ER - TY - JOUR A1 - Kallweit, Stephan A1 - Vanlanduit, S. A1 - Vanherzeele, J. A1 - Brouns, M. T1 - Time resolved PIV reconstruction of periodic flows / Vanlanduit, S. ; Vanherzeele, J. ; Kallweit, S. ; Brouns, M. ; Guillaume, P. JF - PIV'07, 7th International Symposium on Particle Image Velocimetry, Roma, IT, Sep 11-14, 2007 Y1 - 2007 N1 - PIV, Internional Symposium on Particle Image Velocimetry, 7 ; Datei: Vanlanduit.pdf SP - 1 EP - 14 ER - TY - JOUR A1 - Kallweit, Stephan A1 - Uchiyama, R. A1 - Siekmann, H. T1 - Fault Diagnostic Method for Pump Running Conditions Based on Process Modeling and Neural Network / Uchiyama, R. ; Kallweit, S. ; Siekmann, H. JF - International Journal of Rotating Machinery. 4 (1998), H. 1 Y1 - 1998 SN - 1542-3034 SP - 49 EP - 59 ER - TY - JOUR A1 - Kallweit, Stephan A1 - Schimpf, Axel T1 - Photogrammetric Particle Image Velocimetry / Schimpf, Axel ; Kallweit, Stephan JF - Particle image velocimetry : recent improvements; proceedings of the Europiv 2 Workshop held in Zaragoza, Spain, March 31 - April 1, 2003 / edited by M. Stanislas ... Y1 - 2003 SN - 3-540-21423-2 SP - 295 PB - Springer CY - Berlin ER - TY - JOUR A1 - Kallweit, Stephan A1 - Korculanin, O. A1 - Fröhlig, F. A1 - Gabi, M. A1 - Mattern, P. T1 - Photogrammetrische Rekonstruktion von Partikelpositionen mittels Rückprojektion für 3D-PIV JF - Lasermethoden in der Strömungsmesstechnik : 19. Fachtagung, 6. - 8. September 2011, Ilmenau ; [Tagungsband enthält ... Beiträge, die anlässlich der 19. Fachtagaung "Lasermethoden in der Strömungsmesstechnik" ... vorgetragen und diskutiert wurden] / veranst. von der Deutschen Gesellschaft für Laser-Anemometrie GALA e.V. Hrsg. A. Thess... Y1 - 2011 SN - 978-3-9805613-7-2 N1 - Fachtagung Lasermethoden in der Strömungsmesstechnik <19, 2011, Ilmenau> ; Deutsche Gesellschaft für Laser-Anemometrie SP - 28/1 EP - 28/6 PB - Dt. Ges. für Laser-AnemometrieGALA e. V. CY - Karlsruhe ER - TY - JOUR A1 - Kallweit, Stephan A1 - Kisife, F. A1 - Utzenrad, M. A1 - Weber, J. T1 - Hispeed Scanning Stereo PIV hinter einer künstlichen Herzklappe / Kallweit, S. ; Kisife, F. ; Utzenrad, M. ; Weber, J. JF - Lasermethoden in der Strömungsmesstechnik : 16. Fachtagung, 9. - 11. September 2008, Karlsruhe / veranst. von der Deutschen Gesellschaft für Laser-Anemometrie GALA e.V. Hrsg.: B. Ruck Y1 - 2008 SN - 978-3-9805613-4-1 N1 - Fachtagung Lasermethoden in der Strömungsmesstechnik ; (16, 2008, Karlsruhe) ; Deutsche Gesellschaft für Laser-Anemometrie SP - 29 PB - GALA e.V. CY - Karlsruhe ER - TY - JOUR A1 - Kallweit, Stephan A1 - Kaminsky, Radoslav A1 - Rossi, Massimiliano A1 - Morbiducci, Umberto T1 - PIV Measurements of Flows in Artificial Heart Valves / Kaminsky, Radoslav ; Kallweit, Stephan ; Rossi, Massimiliano ; Morbiducci, Umberto ; Scalise, Lorenzo JF - Particle Image Velocimetry - New Developments and Recent Applications Y1 - 2008 SN - 978-3-540-73528-1 N1 - Topics in Applied Physics SP - 55 EP - 72 ER - TY - JOUR A1 - Kallweit, Stephan A1 - Kaminsky, R. A1 - Rossi, M. A1 - Scalise, L. T1 - PIV Measurements with high temporal Resolution behind Artificial Heart Valves / Kaminsky, R. ; Rossi, M. ; Scalise, L. ; Kallweit, S. ; Verdonck, P. JF - Proceedings of the 6th International Symposium on Particle Image Velocimetry Y1 - 2005 N1 - link zum abstract PB - Caltech CY - Pasadena, CA ER - TY - JOUR A1 - Kallweit, Stephan A1 - Kaminsky, R. A1 - Rossi, M. A1 - Morbiducci, U. T1 - Time resolved PIV technique for high temporal resolution measurements of prosthetic heart valves fluid dynamics / Kaminsky, R. ; Rossi, M. ; Morbiducci, U. ; Scalise, L. ; Catellini, P. ; Kallweit, S. ; Verdonck, P. ; Grigioni, M. JF - The International Journal of Artificial Organs. 28 (2005), H. 9 Y1 - 2005 SN - 1724-6040 N1 - Abstracts: XXXII Annual ESAO Congress, 5-8 October 2005, Bologna - Italy SP - 946 ER - TY - JOUR A1 - Kallweit, Stephan A1 - Kaminsky, R. A1 - Rossi, M. A1 - Morbiducci, U. T1 - 2D PIV Study of the flow downstream : Two prototypes of a ney monoleaflet artificial aortic heart valve prosthesis / Kaminsky, R. ; Kramm, K. ; Weber, H. J. ; Simons, A. P. ; Kallweit, S. ; Verdonck, P. R. JF - The International Journal of Artificial Organs. 28 (2005), H. 9 Y1 - 2005 SN - 1724-6040 N1 - Abstracts: XXXII Annual ESAO Congress, 5-8 October 2005, Bologna - Italy SP - 921 ER - TY - JOUR A1 - Kallweit, Stephan A1 - Kaminsky, R. A1 - Rossi, M. A1 - Morbiducci, U. T1 - 3D PIV measurements of prosthetic heart valve dynamics / Kaminsky, R. ; Rossi, M. ; Morbiducci, U. ; Scalise, L. ; Castellini, P. ; Kallweit, S. ; Verdonck, P. ; Grigioni, M. JF - The International Journal of Artificial Organs. 28 (2005), H. 9 Y1 - 2005 SN - 1724-6040 N1 - Abstracts: XXXII Annual ESAO Congress, 5-8 October 2005, Bologna - Italy SP - 868 ER - TY - JOUR A1 - Kallweit, Stephan A1 - Kaminsky, R. A1 - Canneyt, C. van A1 - Eloot, S. T1 - High-Speed und Stereo-PIV in einem künstlichen Blutgefäß / Kallweit, S. ; Kaminsky, R. ; Canneyt, C. van ; Eloot, S. JF - Lasermethoden in der Strömungsmesstechnik: 15. Fachtagung 2007 Rostock / Hrsg.: Alfred Leder .... Y1 - 2007 SN - 978-3-86009-007-7 N1 - Deutsche Gesellschaft für Laser-Anemometrie ; Fachtagung Lasermethoden in der Strömungsmesstechnik <15, 2007, Rostock> SP - 48 ER - TY - JOUR A1 - Kallweit, Stephan A1 - Helbing, M. A1 - Orglmeister, R. A1 - Siekmann, H. E. T1 - Image Processing Techniques with Neural Networks for Flow Visualization in Rotating Machinery / Helbing, M. ; Orgimeiste, R. [Orglmeister, R.] ; Kallweit, S. ; Siekmann, H. E. ; Dues, M. ; Cronemeyer, J. JF - FLUCOME '94 : the 4th Triennial International Symposium on Fluid Control, Measurement and Visualization; August 29 - September 1, 1994, Toulouse, France, International Congress Centre, DIGORA-Labège / CERT/ONERA. General chairman Patrick Hebrard Y1 - 1994 SP - 87 EP - 94 CY - Toulouse ER - TY - JOUR A1 - Kallweit, Stephan A1 - Ebinger, G. A1 - Dues, M. A1 - Siekmann, H. T1 - Anwendung des Laserlichtschnitt-Verfahrens zur qualitativen Untersuchung der Durchströmung von Kreiselpumpen / Ebinger, G. ; Kallweit, S. ; Dues, M. ; Siekmann, H. JF - Lasermethoden in der Strömungsmesstechnik, 2. Fachtagung der Deutschen Gesellschaft für Laser-Anemometrie (GALA), PTB Braunschweig, DE, 14.-16. Sep, 1993 Y1 - 1993 SN - 3-86111-595-6 N1 - Lasermethoden in der Strömungsmesstechnik, Fachtagung, 2 SP - 37.1 EP - 37.4 PB - Shaker CY - Aachen ER - TY - JOUR A1 - Kallweit, Stephan A1 - Dues, Michael A1 - Radke, Michael T1 - Möglichkeiten und Grenzen laseroptischer Verfahren zur Untersuchung hydraulischer Strömungsmaschinen / Dues, Michael ; Kallweit, Stephan ; Radke, Michael JF - Forschung im Ingenieurwesen. 60 (1994), H. 11-12 Y1 - 1994 SN - 0015-7899 SP - 332 EP - 336 ER - TY - JOUR A1 - Kallweit, Stephan A1 - Dues, Michael A1 - Müller, Ulli A1 - Lederer, Thomas T1 - Einsatz der Particle Image Velocimetry zur Untersuchung von Rohrströmungen / Kallweit, Stephan ; Dues, Michael ; Müller, Ulli ; Lederer, Thomas ; Schroll, Michael ; Willert, Christian JF - Lasermethoden in der Strömungsmesstechnik: 15. Fachtagung 2007 Rostock / Hrsg.: Alfred Leder .... Y1 - 2007 SN - 978-3-86009-007-7 N1 - Deutsche Gesellschaft für Laser-Anemometrie ; Fachtagung Lasermethoden in der Strömungsmesstechnik <15, 2007, Rostock> SP - 35 ER - TY - JOUR A1 - Kallweit, Stephan A1 - Dues, M. W. A1 - Siekmann, H. E. T1 - Spectral Analysis of Pressure Fluctuations and Velocity Fields as Investigated on Propeller Pumps / Dues, M. W. ; Kallweit, S. D. ; Siekmann, H. E. JF - Preprints : Fifth International Symposium on Transport Phenomena and Dynamics of Rotating Machinery (ISROMAC-5) : May 8 - 11, 1994, Maui Marriott Hotel, Kaanapali, Maui, Hawaii, U.S.A / sponsored by Pacific Center of Thermal-Fluids Engineering. [W.-J. Yang, chairman] / Vol. B. Y1 - 1994 N1 - International Symposium on Transport Phenomena and Dynamics of Rotating Machinery 5, 1994, Kaanapali, Hawaii SP - 98 EP - 112 ER - TY - JOUR A1 - Kallweit, Stephan A1 - Dues, M. A1 - Siekmann, H. T1 - Particle-Image-Velocimetry (PIV) in rotierenden Maschinen / Dues, M. ; Kallweit, S. ; Siekmann, H. JF - Lasermethoden in der Strömungsmesstechnik, 3. Fachtagung der Deutschen Gesellschaft für Laser-Anemometrie (GALA), Bremen, DE, 5.-7. Sep, 1994 Y1 - 1994 SN - 3-8265-0162-4 N1 - Lasermethoden in der Strömungsmesstechnik, Fachtagung, 3 SP - 19.1 EP - 19-5 PB - Shaker CY - Aachen ER - TY - JOUR A1 - Kallweit, Stephan A1 - Abromeit, W. A1 - Dues, M. A1 - Siekmann, H. T1 - Anwendung der LDA zur Untersuchung der instationären Strömung im Nachleitrad einer axialen Kreiselpumpenstufe / Abromeit, W. ; Dues, M. ; Siekmann, H. ; Kallweit, S. JF - Lasermethoden in der Strömungsmesstechnik, 3. Fachtagung der Deutschen Gesellschaft für Laser-Anemometrie (GALA), Bremen, DE, 5.-7. Sep, 1994 Y1 - 1994 SN - 3-8265-0162-4 N1 - Lasermethoden in der Strömungsmesstechnik, Fachtagung, 3 SP - 27.1 EP - 27.6 PB - Shaker CY - Aachen ER - TY - JOUR A1 - Hötter, Jan-Steffen A1 - Fateri, Miranda A1 - Gebhardt, Andreas T1 - Prozessoptimierung des SLM-Prozesses mit hoch-reflektiven und thermisch sehr gut leitenden Materialien durch systematische Parameterfindung und begleitende Simulationen am Beispiel von Silber JF - RTejournal - Forum für Rapid Technologie N2 - Additive Manufacturing durch Aufschmelzen von Metallpulvern hat sich auf breiter Front als Herstellverfahren, auch für Endprodukte, etabliert. Besonders für die Variante des Selective Laser Melting (SLM) sind Anwendungen in der Zahntechnik bereits weit verbreitet und der Einsatz in sensitiven Branchen wie der Luftfahrt ist in greifbare Nähe gerückt. Deshalb werden auch vermehrt Anstrengungen unternommen, um bisher nicht verarbeitete Materialien zu qualifizieren. Dies sind vorzugsweise Nicht-Eisen- und Edelmetalle, die sowohl eine sehr hohe Reflektivität als auch eine sehr gute Wärmeleitfähigkeit aufweisen – beides Eigenschaften, die die Beherrschung des Laser-Schmelzprozesses erschweren und nur kleine Prozessfenster zulassen. Die Arbeitsgruppe SLM des Lehr- und Forschungsgebietes Hochleistungsverfahren der Fertigungstechnik hat sich unter der Randbedingung einer kleinen und mit geringer Laserleistung ausgestatteten SLM Maschine der Aufgabe gewidmet und am Beispiel von Silber die Parameterfelder für Einzelspuren und wenig komplexe Geometrien systematisch untersucht. Die Arbeiten wurden von FEM Simulationen begleitet und durch metallographische Untersuchungen verifiziert. Die Ergebnisse bilden die Grundlage zur schnellen Parameterfindung bei komplexen Geometrien und bei Veränderungen der Zusammensetzung, wie sie bei zukünftigen Legierungen zu erwarten sind. Die Ergebnisse werden exemplarisch auf unterschiedliche Geometrien angewandt und entsprechende Bauteile gezeigt. N2 - Additive manufacturing by melting of metal powders is a method that has been established even for the manufacturing of final products. In particular, Selective Laser Melting (SLM) is currently applied for prosthetic dentistry. In the near future, this technology will access sensitive industries like aerospace engineering. This leads to the need to process new materials. Therefore, especially non-ferrous metals and noble metals must be determined and qualified. These materials have in common a very high reflectivity and an excellent thermal conductivity. In general, these two properties counteract the control of the melt pool and contribute to very narrow process windows. The “SLM” research team of the Aachen University of Applied Science, AcUAS (FH Aachen) systematically investigated process parameter fields for silver. The work focused on a small SLM desktop machine with comparably low laser power. The results are verified using FEA and metallographic inspections and will support future set-ups for complex geometries. Furthermore, the obtained parameter fields are applied to make different geometric objects and to manufactured parts, which are presented. KW - SLM KW - Selektives Laser Schmelzen KW - Silber Y1 - 2012 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:0009-2-33639 SN - 1614-0923 VL - 9 IS - 1 SP - 1 EP - 14 PB - Fachhoschule Aachen CY - Aachen ER - TY - JOUR A1 - Hötter, Jan-Steffen A1 - Fateri, Miranda A1 - Gebhardt, Andreas T1 - Selective laser melting of metals: desktop machines open up new chances even for small companies JF - Advanced materials research N2 - Additive manufacturing (AM) of metal parts by using Selective Laser Melting (SLM) has become a powerful tool mostly in the area of automotive, aerospace engineering and others. Especially in the field of dentistry, jewelry and related branches that require individualized or even one-of-a-kind products, the direct digital manufacturing process opens up new ways of design and manufacturing. In these fields, mostly small and medium sized businesses (SME) are operating which do not have sufficient human and economic resources to invest in this technology. But to stay competitive, the application of AM can be regarded as a necessity. In this situation a new desktop machine (Realizer SLM 50) was introduced that cost about 1/3 of a shop floor SLM machine and promises small quality parts. To find out whether the machine really is an alternative for SMEs the University of Applied Science, Aachen, Germany, designed, build and optimized typical parts from the dentistry and the jewelry branches using CoCr and silver material, the latter being new with this application. The paper describes the SLM procedure and how to find and optimize the most important parameters. The test is accompanied by digital simulation in order to verify the build parameters and to plan future builds. The procedure is shown as well as the resulting parts made from CoCr and silver material. Y1 - 2012 U6 - http://dx.doi.org/10.4028/www.scientific.net/AMR.622-623.461 SN - 1662-8985 (E-Journal); 1022-6680 (Print) VL - 622-623 SP - 461 EP - 465 PB - Trans Tech Publ. CY - Baech ER - TY - JOUR A1 - Huber, M. A1 - Streblow, R. A1 - Müller, D. A1 - Lange, S. A1 - Joneleit, R. A1 - Sefker, T. A1 - Rau, Sebastian A1 - Wollert, Jörg T1 - Funksignalübertragung in Luftleitungen JF - HLH : Lüftung, Klima, Heizung, Sanitär, Gebäudetechnik Y1 - 2014 SN - 1436-5103 VL - Bd. 65 IS - H. 7/8 SP - 36 EP - 40 ER - TY - JOUR A1 - Heptner, K. A1 - Wollert, Jörg T1 - FML-Report - VDI-Richtlinie 4485 'E-Commerce und Logistik' JF - Logistik für Unternehmen : das Fachmagazin der internen und externen Logistik Y1 - 2005 SN - 0930-7834 N1 - Printausg. in der Bibliothek vorhanden: 43 Z 513 VL - 19 SP - 58 EP - 59 ER - TY - JOUR A1 - Henn, Gudrun A1 - Polaczek, Christa T1 - Studienerfolg in den Ingenieurwissenschaften JF - Das Hochschulwesen : HSW ; Forum für Hochschulforschung, -praxis und -politik Y1 - 2007 SN - 0018-2974 VL - 55 IS - 5 SP - 144 EP - 147 ER - TY - JOUR A1 - Heinrichs, Horst A1 - Weck, M. A1 - Heimann, A. T1 - Rechnerunterstuetzte Aufbereitung von Finite-Elemente-Rechenmodellen-Erfassung der Bauteilgeometrie JF - Industrieanzeiger. 99 (1977), H. 78 Y1 - 1977 SP - 1509 EP - 1512 ER - TY - JOUR A1 - Heinrichs, Horst A1 - Weck, M. T1 - Wirtschaftliche FEM-Strukturanalyse durch graphisch interaktive Netzaufbereitung JF - Industrie Anzeiger. 103 (1981), H. 79 Y1 - 1981 SP - 16 EP - 20 ER - TY - JOUR A1 - Heinrichs, Horst A1 - Weck, M. T1 - Problemloesungen im Rahmen der konstruktiven Gestaltung JF - Industrieanzeiger. 101 (1979), H. 73 Y1 - 1979 SP - 26 EP - 29 ER - TY - JOUR A1 - Heinrichs, Horst A1 - Weck, M. T1 - Rechnerunterstuetzte Aufbereitung von Finite-Elemente-Rechenmodellen -Erstellen der FEM-Netzwerke JF - Industrieanzeiger. 99 (1977), H. 102 Y1 - 1977 SP - 2059 EP - 2061 ER - TY - JOUR A1 - Heinrichs, Horst A1 - Weck, H. T1 - Efficient finite-element structural analysis by interactive graphic mesh generation JF - CIRP Annals. 30 (1981), H. 1 Y1 - 1981 SP - 279 EP - 284 ER - TY - JOUR A1 - Heinrichs, Horst A1 - Steinke, P. T1 - Praxisgerechter Einsatz der Finite-Element-Methode zur Bauteilanalyse JF - Industrie Anzeiger. 103 (1981), H. 79 Y1 - 1981 SP - 42 EP - 43 ER - TY - JOUR A1 - Heinrichs, Horst A1 - Haub, A. T1 - Grafische Oberflächen vereinfachen den FEM-Einsatz JF - CAD-CAM Report. 10 (1991), H. 3 Y1 - 1991 SP - 79 EP - 85 ER - TY - JOUR A1 - Heinrichs, Horst T1 - STEP bietet mehr Y1 - 1992 N1 - Konferenz-Einzelbericht : FEM '92 Congress, Int. FEM-Congress, Baden-Baden, DE, 16.-17. Nov, 1992 SP - 327 EP - 344 PB - IKOSS CY - Stuttgart ER - TY - JOUR A1 - Heinrichs, Horst T1 - Mit Grafik schafft FEM den Durchbruch JF - Maschinen, Anlagen, Verfahren (1993) Y1 - 1993 SN - 0343-043X SP - 58 EP - 59 ER - TY - JOUR A1 - Heinrichs, Horst T1 - Verbindung von CAD und CAE mittels der systemneutralen CAD I Schnittstelle Y1 - 1989 N1 - Konferenz-Einzelbericht : FEM '89, International FEM-Congress, IKO Software Service, Baden-Baden, D, 20.-21.11.1989 SP - 391 EP - 408 ER - TY - JOUR A1 - Heinrichs, Horst T1 - Graphische Datenverarbeitung bei FEM-Berechnungen von Maschinen : interaktive Geometrieerfassung u. Netzwerkerstellung Y1 - 1981 N1 - Dissertation, RWTH Aachen ER - TY - JOUR A1 - Heinrichs, Horst T1 - Graphisch interaktive FE-Netzwerksgenerierung mit dem Programm FEDIG auf Rechnern ab 64 KB-Memory mit Digitizer JF - IKO Software Service. 12 (1983) Y1 - 1983 N1 - Konferenz-Einzelbericht : International FEM-Congress. IKO Software Service, Baden-Baden, 14.- 15.11.1983 SP - 191 EP - 215 ER - TY - JOUR A1 - Heinrichs, Horst T1 - Graphisch interaktiver FEM-Berechnungsarbeitsplatz JF - Konstruktion, Elemente, Methoden. 21 (1984), H. 2 Y1 - 1984 SP - 82 EP - 85 ER - TY - JOUR A1 - Haselgruber, Nikolaus A1 - Mautner, Karin A1 - Thiele, Jan T1 - Usage Space Analysis for Reliability Testing JF - Quality and Reliability Engineering International N2 - During the development process of a complex technical product, one widely used and important technique is accelerated testing where the applied stress on a component is chosen to exceed the reference stress, i.e. the stress encountered in field operation, in order to reduce the time to failure. For that, the reference stress has to be known. Since a complex technical product may fail regarding numerous failure modes, stress in general is highly dimensional rather than scalar. In addition, customers use their products individually, i.e. field operation should be described by a distribution rather than by one scalar stress value. In this paper, a way to span the customer usage space is shown. It allows the identification of worst case reference stress profiles in significantly reduced dimensions with minimal loss of information. The application example shows that even for a complex product like a combustion engine, stress information can be compressed significantly. With low measurement effort it turned out that only three reference stress cycles were sufficient to cover a broad range of customer stress variety. Y1 - 2010 U6 - http://dx.doi.org/10.1002/qre.1155 SN - 1099-1638 N1 - Special Issue: Business and Industrial Statistics: Developments and Industrial Practices in Quality and Reliability VL - 26 IS - 8 SP - 877 EP - 885 PB - Wiley CY - New York ER - TY - JOUR A1 - Hanrath, Wilhelm A1 - Plesken, Wilhelm T1 - Group rings and irreducible representations of space groups / by W. Hanrath and W. Plesken JF - Journal für die reine und angewandte Mathematik. 362 (1985) Y1 - 1985 SN - 0075-4102 SP - 130 EP - 140 ER - TY - JOUR A1 - Hanrath, Wilhelm A1 - Plesken, Wilhelm T1 - The lattices of six-dimensional euclidean space JF - Mathematics of computation. 43 (1984), H. 168 Y1 - 1984 SN - 0025-5718 SP - 573 EP - 587 ER - TY - JOUR A1 - Hanrath, Wilhelm T1 - Character tables of some factor groups of space groups JF - Perfect groups / Derek F. Holt and W. Plesken Y1 - 1989 SN - 0-19-853559-7 SP - 357 EP - 359 PB - Clarendon Press CY - Oxford ER - TY - JOUR A1 - Haag, S. A1 - Zontar, D. A1 - Schleupen, Josef A1 - Müller, T. A1 - Brecher, C. T1 - Chain of refined perception in self-optimizing assembly of micro-optical systems JF - Journal of sensors and sensor systems N2 - Today, the assembly of laser systems requires a large share of manual operations due to its complexity regarding the optimal alignment of optics. Although the feasibility of automated alignment of laser optics has been shown in research labs, the development effort for the automation of assembly does not meet economic requirements – especially for low-volume laser production. This paper presents a model-based and sensor-integrated assembly execution approach for flexible assembly cells consisting of a macro-positioner covering a large workspace and a compact micromanipulator with camera attached to the positioner. In order to make full use of available models from computer-aided design (CAD) and optical simulation, sensor systems at different levels of accuracy are used for matching perceived information with model data. This approach is named "chain of refined perception", and it allows for automated planning of complex assembly tasks along all major phases of assembly such as collision-free path planning, part feeding, and active and passive alignment. The focus of the paper is put on the in-process image-based metrology and information extraction used for identifying and calibrating local coordinate systems as well as the exploitation of that information for a part feeding process for micro-optics. Results will be presented regarding the processes of automated calibration of the robot camera as well as the local coordinate systems of part feeding area and robot base. Y1 - 2014 U6 - http://dx.doi.org/10.5194/jsss-3-87-2014 SN - 2194-878X VL - 3 IS - 1 SP - 87 EP - 95 PB - Copernicus Publ. CY - Göttingen ER - TY - JOUR A1 - Grundmann, Reinhard A1 - Kramer, Carl A1 - Gerhardt, Hans Joachim T1 - Zonenabsaugung und Belüftung für eine Produktionshalle mit zeitweilig auftretender hoher Staubentwicklung JF - DKV-Tagungsbericht, Deutscher Kälte- und Klimatechnischer Verein. 4 (1989) Y1 - 1989 SN - 0172-8849 N1 - Konferenz-Einzelbericht SP - 981 EP - 998 ER - TY - JOUR A1 - Grundmann, Reinhard A1 - Kramer, Carl T1 - Einheitliche Darstellung von Strömungsgeräuschen. Beschreibung der Schalleistung und Darstellung einiger Strömungsgeräusche - 2. Teil. JF - HLH - Zeitschrift für Heizung, Lüftung, Klimatechnik, Haustechnik. 42 (1991), H. 4 Y1 - 1991 SN - 0017-9906 SP - 275 EP - 281 ER - TY - JOUR A1 - Grundmann, Reinhard A1 - Kramer, Carl T1 - Einheitliche Darstellung von Strömungsgeräuschen. Beschreibung der Schalleistung und Darstellung einiger Strömungsgeräusche. 1. Teil. JF - HLH - Zeitschrift für Heizung, Lüftung, Klimatechnik, Haustechnik. 42 (1991), H. 3 Y1 - 1991 SN - 0017-9906 SP - 233 EP - 238 ER - TY - JOUR A1 - Grundmann, Reinhard A1 - Kramer, Carl T1 - Entwurfskriterien für Aeroakustik-Windkanäle und Möglichkeiten zur Nachrüstung bestehender Windkanäle  Entwurfskriterien für Aeroakustik-Windkanäle und Möglichkeiten zur Nachrüstung bestehender Windkanäle JF - Akustik und Aerodynamik des Kraftfahrzeuges : Grundlagen - Optimierungsmethoden - Meß- und Versuchstechnik ; mit 11 Tabellen und 243 Literaturstellen ; [Beiträge der Tagung 'Akustik und Aerodynamik des Kraftfahrzeuges' ... am 1. und 2. Februar 1994] / Sye Y1 - 1995 SN - 3-8169-1190-0 SP - 377 EP - 394 PB - Expert-Verl. CY - Renningen-Malmsheim ER -