TY - JOUR A1 - Willms, Herbert A1 - Beer, Stefan A1 - Fröhlke, K. A1 - Haidn, O.J. A1 - [u.a.], T1 - Regelung eines Wasserstoff-/Sauerstoff-Dampferzeugers mit Hilfe eines modifizierten Zirkondioxid-Sensors Y1 - 1993 N1 - Report: Deutsche Forschungsanstalt für Luft- und Raumfahrt, EN-CA/E (1993) Seite 1-17 (17 Seiten, 14 Bilder, 2 Tabellen, 14 Quellen) ER - TY - JOUR A1 - Kämper, Klaus-Peter A1 - Pappas, D. P. A1 - Hopster, H. T1 - Reversible transition between perpendicular and in-plane magnetization in ultrathin films. Pappas, D. P.; Kämper, K.-P.; Hopster, H. JF - Physical Review Letters. 64 (1990), H. 26 Y1 - 1990 SN - 1079-7114 SP - 3179 EP - 3182 ER - TY - JOUR A1 - Michaux, F. A1 - Mattern, P. A1 - Kallweit, Stephan T1 - RoboPIV: how robotics enable PIV on a large industrial scale JF - Measurement Science and Technology N2 - This work demonstrates how the interaction between particle image velocimetry (PIV) and robotics can massively increase measurement efficiency. The interdisciplinary approach is shown using the complex example of an automated, large scale, industrial environment: a typical automotive wind tunnel application. Both the high degree of flexibility in choosing the measurement region and the complete automation of stereo PIV measurements are presented. The setup consists of a combination of three robots, individually used as a 6D traversing unit for the laser illumination system as well as for each of the two cameras. Synchronised movements in the same reference frame are realised through a master-slave setup with a single interface to the user. By integrating the interface into the standard wind tunnel management system, a single measurement plane or a predefined sequence of several planes can be requested through a single trigger event, providing the resulting vector fields within minutes. In this paper, a brief overview on the demands of large scale industrial PIV and the existing solutions is given. Afterwards, the concept of RoboPIV is introduced as a new approach. In a first step, the usability of a selection of commercially available robot arms is analysed. The challenges of pose uncertainty and importance of absolute accuracy are demonstrated through comparative measurements, explaining the individual pros and cons of the analysed systems. Subsequently, the advantage of integrating RoboPIV directly into the existing wind tunnel management system is shown on basis of a typical measurement sequence. In a final step, a practical measurement procedure, including post-processing, is given by using real data and results. Ultimately, the benefits of high automation are demonstrated, leading to a drastic reduction in necessary measurement time compared to non-automated systems, thus massively increasing the efficiency of PIV measurements. Y1 - 2018 U6 - http://dx.doi.org/10.1088/1361-6501/aab5c1 SN - 1361-6501 N1 - Special Section on the 12th International Symposium on Particle Image Velocimetry (PIV 2017) VL - 29 IS - 7 SP - 074009 PB - IOP CY - Bristol ER - TY - JOUR A1 - Starke, Günther A1 - Ahlbehrendt, Norbert A1 - Bischoff, Rainer A1 - Melzer, Harald A1 - Sieber, Sven A1 - Senk, Burkhard A1 - Kramarczyk, Peter T1 - RoboTOOL. Technologien für den ortsflexiblen Einsatz von Robotern bei temporären Arbeitsaufgaben in der Fertigung JF - wt Werkstattstechnik online Y1 - 2009 SN - 1436-4980 VL - Bd. 99 IS - H. 9 SP - 661 EP - 670 ER - TY - JOUR A1 - Gebhardt, Andreas A1 - Brücker, Christoph A1 - Schmidt, Frank-Michael T1 - RP gestützte Herstellung komplexer transparenter Hohlräume für die Strömungsanalyse N2 - Die Berechnung der Durchströmung von Bauteilen ist gegenüber derjenigen von umströmten Bauteilen deutlich im Hintertreffen. Das liegt vor allem an der fehlenden Verfügbarkeit geeigneter optisch transparenter Modellkanäle für die experimentelle Analyse. Der Beitrag stellt ein Verfahren zur Herstellung transparenter durchströmter Geometrien auf der Basis generativ gefertigter Urmodelle vor. Damit können beliebig komplexe Innenströmungen optisch analysiert werden. Anhand von zwei Beispielen aus der Medizin, der Modellierung der oberen Atemwege und des Bronchialbaums, wird das Verfahren vorgeführt. Der generative Bauprozess mittels 3D-Printing wird beschrieben und die Abformung in transparentem Silikon gezeigt. Schließlich werden beispielhaft der Messaufbau und Ergebnisse der Anwendung vorgestellt. Das Verfahren bildet die Grundlage für die Analyse und Berechnung komplexer Innenströmungen und trägt somit zur Verbesserung zahlreicher technischer Anwendungen bei. N2 - Unlike the flow around technical products the interior flow is not understood very well. That’s mainly because of a lack of suitable transparent investigation tunnels that are needed to apply optical methods. The paper proposes a procedure to make precise complex hollow structures from a highly transparent material using masters from generative or Rapid Prototyping processes. Taking two examples from the medical field, the upper human airways and the bronchial tree, the entire process is shown. The 3D Printing build process is illustrated as well as the silicon casting process. Finally the measuring equipment is demonstrated and sample results are given. The process establishes the basis for the investigation and calculation of complex interior flow pattern and therefore contributes to a better understanding and consequently improvement of appropriate technical products. KW - Rapid prototyping KW - Rapid Prototyping KW - Strömungsanalyse KW - Innenströmung KW - Modellkanäle KW - 3D-Printing Y1 - 2005 ER - TY - JOUR A1 - Babilon, Katharina A1 - Wilbring, Daniela A1 - Tappert, Tim A1 - Pfaff, Raphael A1 - Enning, Manfred T1 - Schienenfahrzeugtechnik hands on – FH Aachen IMechE Railway Challenge JF - Ingenieurspiegel Y1 - 2018 SN - 1868-5919 IS - 2 SP - 20 EP - 22 PB - Public Verlag CY - Bingen ER - TY - JOUR A1 - Wollert, Jörg T1 - Schlaue Produktion von smarten Autos : hinter der Smart-Produktion steckt ein innovatives Logistikkonzept JF - Technica Y1 - 1999 SN - 0040-866X VL - Bd. 48 IS - H. 4 SP - 20 EP - 23 ER - TY - JOUR A1 - Gebhardt, Andreas T1 - Schnell und flexibel zur Kleinserie. Effizienzsteigerung bei der Realisierung von Komponenten und Teilsystemen JF - Ingenieur-Werkstoffe. 8 (1999), H. 3 Y1 - 1999 SN - 0935-5715 SP - 8 EP - 14 ER - TY - JOUR A1 - Gebhardt, Andreas A1 - Guntermann, P. A1 - Häming, L. T1 - Schweißen mit dem Nd:YAG-Laser JF - Der Praktiker, Schweißen und Schneiden. 49 (1997), H. 4 Y1 - 1997 SN - 0554-9965 SP - 170 EP - 172 ER - TY - JOUR A1 - Starke, Günther A1 - Strunz, U. A1 - Spieß, C. T1 - Schweißprozeßparameteroptimierung mit Fuzzy-Logik JF - Schweißen und Schneiden. 47 (1995), H. 6 Y1 - 1995 SN - 0036-7184 SP - 494 EP - 503 ER -