TY  - JOUR
A1  - Anik, Sabri
A1  - Topuz, A.
A1  - Tuncel, H. S.
T1  - Einfluß der Parameter beim Diffusionsschweißen der Stähle X 210 Cr 12 und 25 MoCr 4 auf ihre mechanischen Eigenschaften
JF  - Schweißen und Schneiden : Fachzeitschrift für Schweißen und verwandte Verfahren
Y1  - 1991
SN  - 0036-7184
VL  - 43
IS  - 6
SP  - 341
EP  - 344
ER  - 
TY  - JOUR
A1  - Peeken, Heinz
A1  - Benner, Joachim
A1  - Platt, Werner
T1  - Ausfallkriterien elastomerbestückter Wellenkupplungen
JF  - Antriebstechnik : Konstruktion, Entwicklung und Anwendung von Antrieben und Steuerungen ; Organ der Forschungsvereinigung Antriebstechnik e.V.
Y1  - 1989
SN  - 0341-2652
VL  - 28
IS  - 11
SP  - 85
EP  - 88
PB  - Vereinigte Fachverl.
CY  - Mainz
ER  - 
TY  - JOUR
A1  - Eichler, Fabian
A1  - Balc, Nicolae
A1  - Bremen, Sebastian
A1  - Nink, Philipp
T1  - Investigation of laser powder bed fusion parameters with respect to their influence on the thermal conductivity of 316L samples
JF  - Journal of Manufacturing and Materials Processing
N2  - The thermal conductivity of components manufactured using Laser Powder Bed Fusion (LPBF), also called Selective Laser Melting (SLM), plays an important role in their processing. Not only does a reduced thermal conductivity cause residual stresses during the process, but it also makes subsequent processes such as the welding of LPBF components more difficult. This article uses 316L stainless steel samples to investigate whether and to what extent the thermal conductivity of specimens can be influenced by different LPBF parameters. To this end, samples are set up using different parameters, orientations, and powder conditions and measured by a heat flow meter using stationary analysis. The heat flow meter set-up used in this study achieves good reproducibility and high measurement accuracy, so that comparative measurements between the various LPBF influencing factors to be tested are possible. In summary, the series of measurements show that the residual porosity of the components has the greatest influence on conductivity. The degradation of the powder due to increased recycling also appears to be detectable. The build-up direction shows no detectable effect in the measurement series.
KW  - Additive manufacturing
KW  - LPBF
KW  - SLM
KW  - Thermal conductivity
KW  - 316L
Y1  - 2024
U6  - https://doi.org/10.3390/jmmp8040166
SN  - 2504-4494
N1  - Corresponding author: Fabian Eichler
VL  - 8
IS  - 4
PB  - MDPI
CY  - Basel
ER  - 
TY  - JOUR
A1  - Raffeis, Iris
A1  - Adjei-Kyeremeh, Frank
A1  - Vroomen, Uwe
A1  - Westhoff, Elmar
A1  - Bremen, Sebastian
A1  - Hohoi, Alexandru
A1  - Bührig-Polaczek, Andreas
T1  - Qualification of a Ni-Cu alloy for the laser powder bed fusion process (LPBF): Its microstructure and mechanical properties
JF  - Applied Sciences
N2  - As researchers continue to seek the expansion of the material base for additive manufacturing, there is a need to focus attention on the Ni–Cu group of alloys which conventionally has wide industrial applications. In this work, the G-NiCu30Nb casting alloy, a variant of the Monel family of alloys with Nb and high Si content is, for the first time, processed via the laser powder bed fusion process (LPBF). Being novel to the LPBF processes, optimum LPBF parameters were determined, and hardness and tensile tests were performed in as-built conditions and after heat treatment at 1000 °C. Microstructures of the as-cast and the as-built condition were compared. Highly dense samples (99.8% density) were achieved after varying hatch distance (80 µm and 140 µm) with scanning speed (550 mm/s–1500 mm/s). There was no significant difference in microhardness between varied hatch distance print sets. Microhardness of the as-built condition (247 HV0.2) exceeded the as-cast microhardness (179 HV0.2.). Tensile specimens built in vertical (V) and horizontal (H) orientations revealed degrees of anisotropy and were superior to conventionally reported figures. Post heat treatment increased ductility from 20% to 31% (V), as well as from 16% to 25% (H), while ultimate tensile strength (UTS) and yield strength (YS) were considerably reduced.
Y1  - 2020
U6  - https://doi.org/10.3390/app10103401
SN  - 2076-3417
N1  - Special Issue Materials Development by Additive Manufacturing Techniques
VL  - 10
IS  - Art. 3401
SP  - 1
EP  - 15
PB  - MDPI
CY  - Basel
ER  -