TY - JOUR A1 - Pieper, Martin A1 - Klein, Peter T1 - A simple and accurate numerical network flow model for bionic micro heat exchangers JF - Heat mass transfer Y1 - 2011 SN - 0947-7411 VL - 47 IS - 5 SP - 491 EP - 503 PB - Springer CY - Berlin ER - TY - JOUR A1 - Pieper, Martin A1 - Klein, Peter T1 - Application of simple, periodic homogenization techniques to non-linear heat conduction problems in non-periodic, porous media JF - Heat mass transfer N2 - Often, detailed simulations of heat conduction in complicated, porous media have large runtimes. Then homogenization is a powerful tool to speed up the calculations by preserving accurate solutions at the same time. Unfortunately real structures are generally non-periodic, which requires unpractical, complicated homogenization techniques. We demonstrate in this paper, that the application of simple, periodic techniques to realistic media, that are just close to periodic, gives accurate, approximative solutions. In order to obtain effective parameters for the homogenized heat equation, we have to solve a so called “cell problem”. In contrast to periodic structures it is not trivial to determine a suitable unit cell, which represents a non-periodic media. To overcome this problem, we give a rule of thumb on how to choose a good cell. Finally we demonstrate the efficiency of our method for virtually generated foams as well as real foams and compare these results to periodic structures. Y1 - 2012 U6 - http://dx.doi.org/10.1007/s00231-011-0879-4 SN - 0947-7411 VL - 48 IS - 2 SP - 291 EP - 300 PB - Springer CY - Berlin ER - TY - JOUR A1 - Pham, Phu Tinh A1 - Staat, Manfred T1 - An Upper Bound Algorithm for Limit and Shakedown Analysis of Bounded Linearly Kinematic Hardening Structures JF - Limit State of Materials and Structures : Direct Methods 2. Saxcé, Géry de (Hrsg.) Y1 - 2013 SN - 978-94-007-5424-9 SP - 71 EP - 87 PB - Springer CY - Dordrecht ER - TY - JOUR A1 - Tran, Thanh Ngoc A1 - Staat, Manfred T1 - An Edge-Based Smoothed Finite Element Method for Primal-Dual Shakedown Analysis of Structures Under Uncertainties JF - Limit State of Materials and Structures : Direct Methods 2. Saxcé, Géry de (Hrsg.) Y1 - 2013 SN - 978-94-007-5424-9 SP - 89 EP - 102 PB - Springer CY - Dordrecht ER - TY - CHAP A1 - Mandelartz, Johannes T1 - VDI-Richtlinien – mit Technischen Regeln Wirtschaftlichkeit erhöhen und Standards setzen T2 - Betriebliche Instandhaltung N2 - Der Verein Deutscher Ingenieure e.V. (VDI) ist ein gemeinnütziger, wirtschaftlich und politisch unabhängiger, technisch-wissenschaftlicher Verein von Ingenieuren und Naturwissenschaftlern. Mit über 137 000 persönlich zugeordneten Mitgliedern ist er eine der größten Ingenieur-Vereinigungen Europas und gilt in Deutschland als führender Sprecher der Technik und der Ingenieure. 1856 gegründet, hat er viele für die Technik wesentliche Entwicklungen in Gang gesetzt, so im Bereich der technischen Überwachung, der technischen Regelsetzung und Normung, der Arbeitsstudien, im gewerblichen Rechtsschutz und im Patentwesen. Seit seiner Gründung sieht es der VDI als seine Aufgabe, "das Zusammenwirken aller geistiger Kräfte der Technik im Bewusstsein ethischer Verantwortung zu fördern" und die Lebensmöglichkeiten aller Menschen durch Entwicklung und sinnvoller Anwendung technischer Mittel zu verbessern. Y1 - 2009 SN - 978-3-642-00502-2 U6 - http://dx.doi.org/10.1007/978-3-642-00502-2_26 SP - 311 EP - 317 PB - Springer CY - Berlin [u.a.] ER - TY - JOUR A1 - Nomdedeu, Mar Monsonis A1 - Willen, Christine A1 - Schieffer, Andre A1 - Arndt, Hartmut T1 - Temperature-dependent ranges of coexistence in a model of a two-prey-one-predator microbial food web JF - Marine Biology N2 - The objective of our study was to analyze the effects of temperature on the population dynamics of a three-species food web consisting of two prey bacteria (Pedobacter sp. and Acinetobacter johnsonii) and a protozoan predator (Tetrahymena pyriformis) as model organisms. We assessed the effects of temperature on the growth rates of all three species with the objective of developing a model with four differential equations based on the experimental data. The following hypotheses were tested at a theoretical level: Firstly, temperature changes can affect the dynamic behavior of a system by temperature-dependent parameters and interactions and secondly, food web response to temperature cannot be derived from the single species temperature response. The main outcome of the study is that temperature changes affect the parameter range where coexistence is possible within all three species. This has significant consequences on our ideas regarding the evaluation of effects of global warming. Y1 - 2012 U6 - http://dx.doi.org/10.1007/s00227-012-1966-x SN - 1432-1793 VL - 159 IS - 11 SP - 2423 EP - 2430 PB - Springer CY - Berlin ER - TY - CHAP A1 - Röth, Thilo A1 - Kampker, Achim A1 - Reisgen, Uwe A1 - Hameyer, Kay A1 - De Doncker, R. W. T1 - Entwicklung von elektrofahrzeugspezifischen Systemen T2 - Elektromobilität : Grundlagen einer Zukunftstechnologie N2 - Die Fahrzeugkarosserie bildet als größte funktionale und organisatorische Systemeinheit ein zentrales Kompetenzfeld der OEMs. Für den Fahrzeughersteller stellt der Karosserierohbau eine hohe Kernkompetenz sowohl in der Produktentwicklung als auch in der Produktion dar. Neue, innovative Karosseriebauweisen, bspw. aufgrund eines neuen Fahrzeugkonzeptes oder neuer Anforderungen, bedeuten für den OEM auch gleichzeitig die intensive Auseinandersetzung mit Kompetenzfokussierung bzw. Wertschöpfungsverlagerungen. Y1 - 2013 SN - 978-3-642-31986-0 SP - 235 EP - 336 PB - Springer CY - Berlin ER - TY - CHAP A1 - Reimer, Lars A1 - Braun, Carsten A1 - Wellmer, Georg A1 - Behr, Marek A1 - Ballmann, Josef T1 - Development of a modular method for computational aero-structural analysis of aircraft T2 - Summary of flow modulation and fluid-structure interaction findings. Results of the Collaborative Research Center SFB 401 at the RWTH Aachen University, Aachen, Germany, 1997-2008 / ed.: Wolfgang Schröder. Notes on numerical fluid mechanics and multidisciplinary design. Vol. 109 Y1 - 2010 SN - 978-3-642-04087-0 SP - 205 EP - 238 PB - Springer CY - Berlin ER - TY - CHAP A1 - Reimer, Lars A1 - Wellmer, Georg A1 - Braun, Carsten A1 - Ballmann, Josef T1 - Computational methods for aero-structural analysis and optimisation of aircrafts based on reduced-order structural models T2 - MEGADESIGN and MegaOpt - German initiatives for aerodynamic simulation and optimization in aircraft design. Results of the closing symposium of the MEGADESIGN and MegaOpt projects, Braunschweig, Germany, 23 - 24 May, 2007 / Norbert Kroll ... (Eds.) Notes on numerical fluid mechanics and multidisciplinary design. Vol. 107 N2 - In this part of the MEGADESIGN project, aeroelastic effects are introduced into the aerodynamic analysis of aircrafts by coupling DLR’s flow solvers TAU and FLOWer to a Timoshenko-beam solver. The emerging aeroelastic solvers and a method for the automatic identification of Timoshenko-beam models for wing-box structures were integrated into a simulation environment enabling the combined optimisation of aerodynamic wing shape and structure. Y1 - 2009 SN - 978-3-642-04092-4 SP - 135 EP - 150 PB - Springer CY - Berlin ER - TY - CHAP A1 - Reimer, Lars A1 - Braun, Carsten A1 - Ballmann, Josef T1 - Computational study of the aeroelastic equilibrium configuration of a swept wind tunnel wing model in subsonic flow T2 - High performance computing in science and engineering '06. Transactions of the High Performance Computing Center Stuttgart (HLRS) 2006 / Wolfgang E. Nagel ... Eds. N2 - In the Collaborative Research Center SFB 401 at RWTH Aachen University, the numerical aeroelastic method SOFIA for direct numerical aeroelastic simulation is being progressively developed. Numerical results obtained by applying SOFIA were compared with measured data of static and dynamic aeroelastic wind tunnel tests for an elastic swept wing in subsonic flow. Y1 - 2007 SN - 978-3-540-36165-7 SP - 421 EP - 434 PB - Springer CY - Berlin [u.a.] ER - TY - CHAP A1 - Braun, Carsten A1 - Boucke, Alexander A1 - Ballmann, Josef T1 - Numerical study of the influence of dynamic pressure and deflected ailerons on the deformation of a high speed wing model T2 - High performance computing in science and engineering '04. Transactions of the High Performance Computing Center Stuttgart (HLRS) 2004 / Eds.: Egon Krause ... Y1 - 2005 SN - 3-540-22943-4 SP - 225 EP - 236 PB - Springer CY - Berlin ER - TY - CHAP A1 - Braun, Carsten A1 - Boucke, Alexander A1 - Hanke, M. A1 - Karavas, Alexandros A1 - Ballmann, Josef T1 - Prediction of the model deformation of a high speed transport aircraft type wing by direct aeroelastic simulation T2 - High performance computing in science and engineering '03. Transactions of the High Performance Computing Center Stuttgart (HLRS) 2003 / Eds.: Egon Krause ... Y1 - 2003 SN - 978-3-540-40850-5 SP - 331 EP - 342 PB - Springer CY - Berlin ER - TY - CHAP A1 - Britten, G. A1 - Braun, Carsten A1 - Hesse, M. A1 - Ballmann, Josef T1 - Computational aeroelasticity with reduced structural models T2 - Flow modulation and fluid-structure interaction at airplane wings : research results of the Collaborative Research Center SFB 401 at RWTH Aachen, University of Technology, Aachen, Germany / Josef Ballmann (Ed.) Notes on numerical fluid mechanics and multidisciplinary design. Vol. 84 Y1 - 2003 SN - 3-540-40209-8 SP - 275 EP - 299 PB - Springer CY - Berlin ER - TY - CHAP A1 - Cresser, J. D. A1 - Häger, J. A1 - Leuchs, G. A1 - Rateike, Franz-Matthias A1 - Walther, H. T1 - Resonance fluorescence of atoms in strong monochromatic laser fields T2 - Dissipative systems in quantum optics. Ed. by Rodolfo Bonifacio. Topics in current physics. Vol. 27 N2 - The investigation of atomic resonance fluorescence has always been of special interest as a means for the determination of atomic parameters. In addition, information on the interaction mechanism between atoms and radiation can be obtained. In the standard fluorescence experiment the frequency distribution of the incident photons is larger than the natural width of the respective transition; as a consequence the correlation time in the photon-atom interaction is determined by the lifetime of the atoms in the excited state. With the development of lasers and especially of tunable dye lasers in recent years it became possible to study the case where the incident radiation has a spectral distribution which is narrower than the natural width. This corresponds to a correlation time of the incoming light wave which is much longer than the excited-state lifetime. In this chapter a survey of experiments on the resonance fluorescence of atoms in monochromatic laser fields will be given. Y1 - 1982 SN - 978-3-642-81719-9 U6 - http://dx.doi.org/10.1007/978-3-642-81717-5_3 SP - 21 EP - 59 PB - Springer CY - Berlin ER - TY - CHAP A1 - Weber, Hans-Joachim T1 - Applied physics of compressible and incompressible fluids T2 - Critical care nephrology / [Hrsg.:] Claudio Ronco and Rinaldo Bellomo Y1 - 1998 SN - 978-94-010-6306-7 SP - 63 EP - 84 PB - Springer CY - Dordrecht ER - TY - CHAP A1 - Dikta, Gerhard T1 - Fundamentals of applied probability and basic statistics T2 - Critical care nephrology / [Hrsg.:] Claudio Ronco and Rinaldo Bellomo Y1 - 1998 SN - 978-94-010-6306-7 SP - 51 EP - 61 PB - Springer CY - Dordrecht ER - TY - CHAP A1 - Dachwald, Bernd A1 - Ulamec, Stephan A1 - Biele, Jens T1 - Clean in situ subsurface exploration of icy environments in the solar system T2 - Habitability of other planets and satellites. - (Cellular origin, life in extreme habitats and astrobiology ; 28) N2 - "To assess the habitability of the icy environments in the solar system, for example, on Mars, Europa, and Enceladus, the scientific analysis of material embedded in or underneath their ice layers is very important. We consider self-steering robotic ice melting probes to be the best method to cleanly access these environments, that is, in compliance with planetary protection standards. The required technologies are currently developed and tested." Y1 - 2013 SN - 978-94-007-6545-0 (Druckausgabe) SN - 978-94-007-6546-7 (E-Book) SP - 367 EP - 397 PB - Springer CY - Dordrecht ER - TY - CHAP A1 - Meliß, Michael A1 - Späte, Frank T1 - Berechnung von Sonnenstand und -strahlung T2 - Regenerative Energiequellen : Praktikum / ed. Michael Meliß Y1 - 1997 SN - 3-540-63218-2 U6 - http://dx.doi.org/10.1007/978-3-642-60864-3_2 SP - 5 EP - 22 PB - Springer CY - Berlin ER - TY - CHAP A1 - Meliß, Michael A1 - Späte, Frank T1 - Auslegung von solarthermischen Anlagen T2 - Regenerative Energiequellen : Praktikum / ed. Michael Meliß Y1 - 1997 SN - 3-540-63218-2 U6 - http://dx.doi.org/10.1007/978-3-642-60864-3_3 SP - 23 EP - 47 PB - Springer CY - Berlin ER - TY - JOUR A1 - Dietzel, F. A1 - Weber, Hans-Joachim A1 - Porschen, W. A1 - Feinendegen, L. E. T1 - Zur Wärmeempfindlichkeit von oxischen und hypoxischen Zellen in einem Tumor JF - Naturwissenschaften Y1 - 1976 U6 - http://dx.doi.org/10.1007/BF00622808 SN - 0028-1042 VL - 63 IS - 12 SP - 585 EP - 586 PB - Springer CY - Heidelberg ER - TY - CHAP A1 - Dilthey, Ulrich A1 - Brandenburg, Annette A1 - Schleser, Markus T1 - Mikrokleben T2 - Montage hybrider Mikrosysteme : Handhabungs- und Fügetechniken für die Klein- und Mittelserienfertigung Y1 - 2005 SN - 978-3-540-23706-8 SP - 161 EP - 172 PB - Springer CY - Berlin [u.a.] ER - TY - CHAP A1 - Hirt, Gerhard A1 - Bleck, Wolfgang A1 - Bobzin, Kirsten A1 - Schleser, Markus A1 - [u.a.], T1 - Hybride Produktionssysteme T2 - Integrative Produktionstechnik für Hochlohnländer / hrsg. von Christian Brecher N2 - Während die virtuelle Produktentstehungskette große Gestaltungsfreiräume bietet, ist die reale Produktentstehungskette durch wesentlich mehr Randbedingungen gekennzeichnet, die nicht oder nur ansatzweise beeinflussbar sind. Die Realisierung des aus logistischer Sicht optimalen One-Piece-Flow bei gleichzeitiger Steigerung von Flexibilität und Produktivität sowie des Verschiebens der Grenze des technologisch Machbaren müssen in zukünftigen Forschungsansätzen gleichermaßen betrachtet werden. Die Grenzverschiebung auf Basis der Integration von Technologien ist dabei ein viel versprechender Ansatz, der es in vielen Fällen ermöglicht, in allen genannten Zielrichtungen gleichermaßen Potentiale zu erschließen. Y1 - 2011 SN - 978-3-642-20692-4 (Print) ; 978-3-642-20693-1 (E-Book) U6 - http://dx.doi.org/10.1007/978-3-642-20693-1_5 SP - 465 EP - 745 PB - Springer CY - Berlin [u.a.] ER - TY - JOUR A1 - Reisgen, Uwe A1 - Schleser, Markus A1 - Mokrov, Oleg A1 - Zabirov, Alexander T1 - Virtual welding equipment for simulation of GMAW processes with integration of power source regulation JF - Frontiers of materials science Y1 - 2011 SN - 2095-0268 (E-Journal); 2095-025X (Print) VL - Vol. 5 IS - Iss. 2 SP - 79 EP - 89 PB - Springer CY - Berlin ER - TY - CHAP A1 - Tran, Thanh Ngoc A1 - Staat, Manfred T1 - Shakedown analysis of Reissner-Mindlin plates using the edge-based smoothed finite element method T2 - Direct methods for limit states in structures and materials / Dieter Weichert ; Alan Ponter, ed. N2 - This paper concerns the development of a primal-dual algorithm for limit and shakedown analysis of Reissner-Mindlin plates made of von Mises material. At each optimization iteration, the lower bound of the shakedown load multiplier is calculated simultaneously with the upper bound using the duality theory. An edge-based smoothed finite element method (ES-FEM) combined with the discrete shear gap (DSG) technique is used to improve the accuracy of the solutions and to avoid the transverse shear locking behaviour. The method not only possesses all inherent features of convergence and accuracy from ES-FEM, but also ensures that the total number of variables in the optimization problem is kept to a minimum compared with the standard finite element formulation. Numerical examples are presented to demonstrate the effectiveness of the present method. Y1 - 2014 SN - 978-94-007-6826-0 (Print) 978-94-007-6827-7 (Online) U6 - http://dx.doi.org/10.1007/978-94-007-6827-7_5 SP - 101 EP - 117 PB - Springer CY - Dordrecht [u.a.] ER - TY - JOUR A1 - Winckler, Silvia A1 - Krueger, Rolf A1 - Schnitzler, Thomas A1 - Zang, Werner A1 - Fischer, Rainer A1 - Biselli, Manfred T1 - A sensitive monitoring system for mammalian cell cultivation processes: a PAT approach JF - Bioprocess and biosystems engineering N2 - Biopharmaceuticals such as antibodies are produced in cultivated mammalian cells, which must be monitored to comply with good manufacturing practice. We, therefore, developed a fully automated system comprising a specific exhaust gas analyzer, inline analytics and a corresponding algorithm to precisely determine the oxygen uptake rate, carbon dioxide evolution rate, carbon dioxide transfer rate, transfer quotient and respiratory quotient without interrupting the ongoing cultivation, in order to assess its reproducibility. The system was verified using chemical simulation experiments and was able to measure the respiratory activity of hybridoma cells and DG44 cells (derived from Chinese hamster ovary cells) with satisfactory results at a minimum viable cell density of ~2.0 × 10⁵ cells ml⁻¹. The system was suitable for both batch and fed-batch cultivations in bubble-aerated and membrane-aerated reactors, with and without the control of pH and dissolved oxygen. Y1 - 2014 U6 - http://dx.doi.org/10.1007/s00449-013-1062-8 SN - 1615-7591 (Print) 1615-7605 (Online) VL - 37 IS - 5 SP - 901 EP - 912 PB - Springer CY - Berlin, Heidelberg ER - TY - JOUR A1 - Deppe, Veronika Maria A1 - Bongaerts, Johannes A1 - O'Connell, Timothy A1 - Maurer, Karl-Heinz A1 - Meinhardt, Friedhelm T1 - Enzymatic deglycation of Amadori products in bacteria JF - Applied microbiology and biotechnology Y1 - 2011 SN - 1432-0614 (E-Journal); 0171-1741 (Print); 0175-7598 (Print); 0340-2118 (Print) VL - Vol. 90 IS - Iss. 2 SP - 399 EP - 406 PB - Springer CY - Berlin ER - TY - JOUR A1 - Kirschner-Hermanns, Ruth A1 - Klementz, T. A1 - Haselhuhn, Angelika A1 - Jakse, Gerhard A1 - Heidenreich, A. A1 - Brehmer, Bernhard T1 - Drangsymptomatik nach onkologisch erfolgreicher Prostatakarzinomtherapie : prospektive Studie zum Einfluss von Therapiemodalität, Morbidität und epidemiologischen Faktoren auf die Lebensqualität JF - Der Urologe Y1 - 2011 SN - 1433-0563 VL - Vol. 50 IS - Iss. 11 SP - 1412 EP - 1419 PB - Springer CY - Berlin ER - TY - JOUR A1 - Bung, Daniel B. T1 - Fließcharakteristik und Sauerstoffeintrag bei selbstbelüfteten Gerinneströmungen auf Kaskaden mit gemäßigter Neigung JF - Österreichische Wasser- und Abfallwirtschaft Y1 - 2011 SN - 1613-7566 (E-Journal); 0945-358X (Print) VL - Vol. 63 IS - Iss. 3-4 SP - 76 EP - 81 PB - Springer CY - Berlin ER - TY - CHAP A1 - Wolff, Nino A1 - Seefeldt, Patric A1 - Bauer, Wolfgang A1 - Fiebig, Christopher A1 - Gerding, Patrick A1 - Parow-Souchon, Kai A1 - Pongs, Anna A1 - Reiffenrath, Matti A1 - Ziemann, Thomas T1 - Alternative application of solar sail technology T2 - Advances in solar sailing N2 - The development of Gossamer sail structures for solar sails contributes to a large field of future space applications like thin film solar generators, membrane antennas and drag sails. The focus of this paper is the development of a drag sail based on solar sail technology that could contribute to a reduction of space debris in low Earth orbits. The drag sail design and its connections to solar sail development, a first test on a sounding rocket, as well as the ongoing integration of the drag sail into a triple CubeSat is presented. Y1 - 2014 SN - 978-3-642-34906-5 (Print) ; 978-3-642-34907-2 (E-Book) U6 - http://dx.doi.org/10.1007/978-3-642-34907-2_23 SP - 351 EP - 365 PB - Springer CY - Berlin ER - TY - CHAP A1 - Dachwald, Bernd A1 - Boehnhardt, Herrmann A1 - Broj, Ulrich A1 - Geppert, Ulrich R. M. E. A1 - Grundmann, Jan-Thimo A1 - Seboldt, Wolfgang A1 - Seefeldt, Patric A1 - Spietz, Peter A1 - Johnson, Les A1 - Kührt, Ekkehard A1 - Mottola, Stefano A1 - Macdonald, Malcolm A1 - McInnes, Colin R. A1 - Vasile, Massimiliano A1 - Reinhard, Ruedeger T1 - Gossamer roadmap technology reference study for a multiple NEO Rendezvous Mission T2 - Advances in solar sailing N2 - A technology reference study for a multiple near-Earth object (NEO) rendezvous mission with solar sailcraft is currently carried out by the authors of this paper. The investigated mission builds on previous concepts, but adopts a strong micro-spacecraft philosophy based on the DLR/ESA Gossamer technology. The main scientific objective of the mission is to explore the diversity of NEOs. After direct interplanetary insertion, the solar sailcraft should—within less than 10 years—rendezvous three NEOs that are not only scientifically interesting, but also from the point of human spaceight and planetary defense. In this paper, the objectives of the study are outlined and a preliminary potential mission profile is presented. Y1 - 2014 SN - 978-3-642-34906-5 (Print) ; 978-3-642-34907-2 (E-Book) SP - 211 EP - 226 PB - Springer CY - Berlin [u.a.] ER - TY - CHAP A1 - McInnes, Colin R. A1 - Bothmer, Volker A1 - Dachwald, Bernd A1 - Geppert, Ulrich R. M. E. A1 - Heiligers, Jeannette A1 - Hilgers, Alan A1 - Johnson, Les A1 - Macdonald, Malcolm A1 - Reinhard, Ruedeger A1 - Seboldt, Wolfgang A1 - Spietz, Peter T1 - Gossamer roadmap technology reference study for a Sub-L1 Space Weather Mission T2 - Advances in solar sailing N2 - A technology reference study for a displaced Lagrange point space weather mission is presented. The mission builds on previous concepts, but adopts a strong micro-spacecraft philosophy to deliver a low mass platform and payload which can be accommodated on the DLR/ESA Gossamer-3 technology demonstration mission. A direct escape from Geostationary Transfer Orbit is assumed with the sail deployed after the escape burn. The use of a miniaturized, low mass platform and payload then allows the Gossamer-3 solar sail to potentially double the warning time of space weather events. The mission profile and mass budgets will be presented to achieve these ambitious goals. Y1 - 2014 SN - 978-3-642-34906-5 (Print) ; 978-3-642-34907-2 (E-Book) SP - 227 EP - 242 PB - Springer CY - Berlin [u.a.] ER - TY - CHAP A1 - Macdonald, Malcolm A1 - McGrath, C. A1 - Appourchaux, T. A1 - Dachwald, Bernd A1 - Finsterle, W. A1 - Gizon, L. A1 - Liewer, P. C. A1 - McInnes, Colin R. A1 - Mengali, G. A1 - Seboldt, W. A1 - Sekii, T. A1 - Solanki, S. K. A1 - Velli, M. A1 - Wimmer-Schweingruber, R. F. A1 - Spietz, Peter A1 - Reinhard, Ruedeger ED - Macdonald, Malcolm T1 - Gossamer roadmap technology reference study for a solar polar mission T2 - Advances in solar sailing N2 - A technology reference study for a solar polar mission is presented. The study uses novel analytical methods to quantify the mission design space including the required sail performance to achieve a given solar polar observation angle within a given timeframe and thus to derive mass allocations for the remaining spacecraft sub-systems, that is excluding the solar sail sub-system. A parametric, bottom-up, system mass budget analysis is then used to establish the required sail technology to deliver a range of science payloads, and to establish where such payloads can be delivered to within a given timeframe. It is found that a solar polar mission requires a solar sail of side-length 100–125 m to deliver a ‘sufficient value’ minimum science payload, and that a 2.5 μm sail film substrate is typically required, however the design is much less sensitive to the boom specific mass. Y1 - 2014 SN - 978-3-642-34906-5 U6 - http://dx.doi.org/10.1007/978-3-642-34907-2_17 SP - 243 EP - 257 PB - Springer CY - Berlin, Heidelberg ER - TY - CHAP A1 - Pulini, Paola A1 - Gligorevic, Snjezana T1 - WIMAX performance in the airport environment T2 - Multi-carrier systems & solutions 2009. (Lecture notes in electrical engineering ; 41) N2 - In this paper, the multicarrier physical layers of WiMAX are evaluated in the context of airport data links. The orthogonal frequency-division multiplexing (OFDM) and orthogonal frequency-division multiple-access (OFDMA) cases are applied to the forward link (FL) and reverse link (RL), respectively. The performance of the so called parking and taxi scenarios is presented for airport communications in C-band. Numerical results show that the proposed scheme brings good performance for both the FL and the RL. For the OFDMA case a structure changing called double-tile is also proposed to improve the system performance. Y1 - 2009 SN - 978-90-481-2529-6 (Print) ; 978-90-481-2530-2 (Online) SP - 301 EP - 310 PB - Springer CY - Berlin [u.a.] ER - TY - CHAP A1 - Priede, Gareth A1 - Ferrein, Alexander T1 - Towards passive walking for the fully-actuated biped robot Nao T2 - Emerging trends in computing, informatics, systems sciences, and engineering. (Lecture notes in electrical engineering : vol. 151) N2 - Many biped robots deploy a form of gait that follows the zero moment point (ZMP) approach, that is, the robot is in a stable position at any point in time. This requires the robot to be fully actuated. While very stable, the draw-backs of this approach are a fairly slow gait and high energy consumption. An alternative approach is the so-called passive-dynamic walking, where the gait makes use of the inertia and dynamic stability of the robot. In this paper we describe our ongoing work of combining the principles of passive-dynamic walking on the fully-actuated biped robot Nao, which is also deployed for robotic soccer applications. We present a simple controller that allows the robot to stably rock sidewards, showing a closed limit-cycle. We discuss first results of superimposing a forward motion on the sidewards motion. Based on this we expect to endow the Nao with a fast, robust, and stable passive-dynamic walk on the fully-actuated Nao in the future. Y1 - 2013 SN - 978-1-4614-3557-0 ; 978-1-4614-3558-7 U6 - http://dx.doi.org/10.1007/978-1-4614-3558-7_18 SP - 225 EP - 236 PB - Springer CY - New York, NY ER - TY - JOUR A1 - Alebouyeh Samami, Behzad A1 - Pieper, Martin A1 - Breitbach, Gerd A1 - Hodapp, Josef T1 - Heat production in the windings of the stators of electric machines under stationary condition JF - Heat and mass transfer N2 - In electric machines due to high currents and resistive losses (joule heating) heat is produced. To avoid damages by overheating the design of effective cooling systems is required. Therefore the knowledge of heat sources and heat transfer processes is necessary. The purpose of this paper is to illustrate a good and effective calculation method for the temperature analysis based on homogenization techniques. These methods have been applied for the stator windings in a slot of an electric machine consisting of copper wires and resin. The key quantity here is an effective thermal conductivity, which characterizes the heterogeneous wire resin-arrangement inside the stator slot. To illustrate the applicability of the method, the analysis of a simplified, homogenized model is compared with the detailed analysis of temperature behavior inside a slot of an electric machine according to the heat generation. We considered here only the stationary situation. The achieved numerical results are accurate and show that the applied homogenization technique works in practice. Finally the results of simulations for the two cases, the original model of the slot and the homogenized model chosen for the slot (unit cell), are compared to experimental results. Y1 - 2014 U6 - http://dx.doi.org/10.1007/s00231-014-1371-8 SN - 0947-7411 (Print) ; 1432-1181 (E-Journal) VL - 50 SP - 1707 EP - 1716 PB - Springer CY - Heidelberg ER - TY - CHAP A1 - Niemüller, Tim A1 - Ewert, Daniel A1 - Reuter, Sebastian A1 - Ferrein, Alexander A1 - Jeschke, Sabina A1 - Lakemeyer, Gerhard T1 - RoboCup logistics league sponsored by festo: A competitive factory automation testbed T2 - RoboCup 2013: Robot World Cup XVII : Eindhoven; Netherlands; 1 July 2013 through 1 July 2013. (Lecture notes in computer science ; 8371) N2 - A new trend in automation is to deploy so-called cyber-physical systems (CPS) which combine computation with physical processes. The novel RoboCup Logistics League Sponsored by Festo (LLSF) aims at such CPS logistic scenarios in an automation setting. A team of robots has to produce products from a number of semi-finished products which they have to machine during the game. Different production plans are possible and the robots need to recycle scrap byproducts. This way, the LLSF is a very interesting league offering a number of challenging research questions for planning, coordination, or communication in an application-driven scenario. In this paper, we outline the objectives of the LLSF and present steps for developing the league further towards a benchmark for logistics scenarios for CPS. As a major milestone we present the new automated referee system which helps in governing the game play as well as keeping track of the scored points in a very complex factory scenario. Y1 - 2014 SN - 978-3-662-44467-2 (Print) 978-3-662-44468-9 (Online) SP - 336 EP - 347 PB - Springer CY - Berlin ER - TY - JOUR A1 - Khaydukova, M. M. A1 - Zadorozhnaya, O. A. A1 - Kirsanov, D. O. A1 - Iken, Heiko A1 - Rolka, David A1 - Schöning, Michael Josef A1 - Babain, V. A. A1 - Vlasov, Yu. G. A1 - Legin, A. V. T1 - Multivariate processing of atomic-force microscopy images for detection of the response of plasticized polymeric membranes JF - Russian journal of applied chemistry N2 - The possibility of using the atomic-force microscopy as a method for detection of the analytical signal from plasticized polymeric sensor membranes was analyzed. The surfaces of cadmium-selective membranes based on two polymeric matrices were examined. The digital images were processed with multivariate image analysis techniques. A correlation was found between the surface profile of an ion-selective membrane and the concentration of the ion in solution. Y1 - 2014 U6 - http://dx.doi.org/10.1134/S1070427214030112 SN - 1608-3296 (E-Journal); 1070-4272 (Print) VL - 87 IS - 3 SP - 307 EP - 314 PB - Springer CY - Dordrecht ER - TY - JOUR A1 - Jakob, Felix A1 - Martinez, Ronny A1 - Mandawe, John A1 - Hellmuth, Hendrik A1 - Siegert, Petra A1 - Maurer, Karl-Heinz A1 - Schwaneberg, Ulrich T1 - Surface charge engineering of a Bacillus gibsonii subtilisin protease JF - Applied microbiology and biotechnology Y1 - 2013 SN - 1432-0614 (E-Journal); 0171-1741 (Print); 0175-7598 (Print); 0340-2118 (Print) VL - Vol. 97 IS - Iss. 15 SP - 6793 EP - 6802 PB - Springer CY - Berlin ER - TY - JOUR A1 - Niehaus, F. A1 - Gabor, E. A1 - Wieland, S. A1 - Siegert, Petra A1 - Maurer, Karl-Heinz A1 - Eck, J. T1 - Enzymes for the laundry industries: tapping the vast metagenomic pool of alkaline proteases JF - Microbial biotechnology Y1 - 2011 SN - 1432-0614 (E-Journal); 0171-1741 (Print); 0175-7598 (Print); 0340-2118 (Print) VL - Vol. 4 IS - Iss. 6 SP - 767 EP - 776 PB - Springer CY - Berlin ER - TY - CHAP A1 - Pietsch, Wolfram T1 - A framework for strategic positioning of IT-products T2 - Software business : from physical products to software services and solutions : 4th International Conference on Software Business, ICSOB 2013; Potsdam; Germany; 11 June 2013 through 14 June 2013. (Lecture notes in business information processing ; 150) N2 - IT Products are viewed and managed differently depending on the perspectives and the stage within the life cycle. A model is presented that integrates different perspectives and stages serving as an aid for the analysis of business models and focused positioning of IT-products. Four generic business models are analysed with regard to the product management function in general and the positioning field for IT-products specifically: off-the-shelf (license), license plus service, project, and system service (incl. cloud computing). KW - Strategic Business Planning KW - IT Products KW - Business Models KW - Product Management Y1 - 2013 U6 - http://dx.doi.org/10.1007/978-3-642-39336-5_11 SP - 102 EP - 116 PB - Springer CY - Berlin ER - TY - CHAP A1 - Kirchner, Patrick A1 - Reisert, Steffen A1 - Schöning, Michael Josef T1 - Calorimetric gas sensors for hydrogen peroxide monitoring in aseptic food processes T2 - Gas sensing fundamentals. (Springer Series on Chemical Sensors and Biosensors ; 15) N2 - For the sterilisation of aseptic food packages it is taken advantage of the microbicidal properties of hydrogen peroxide (H2O2). Especially, when applied in vapour phase, it has shown high potential of microbial inactivation. In addition, it offers a high environmental compatibility compared to other chemical sterilisation agents, as it decomposes into oxygen and water, respectively. Due to a lack in sensory detection possibilities, a continuous monitoring of the H2O2 concentration was recently not available. Instead, the sterilisation efficacy is validated using microbiological tests. However, progresses in the development of calorimetric gas sensors during the last 7 years have made it possible to monitor the H2O2 concentration during operation. This chapter deals with the fundamentals of calorimetric gas sensing with special focus on the detection of gaseous hydrogen peroxide. A sensor principle based on a calorimetric differential set-up is described. Special emphasis is given to the sensor design with respect to the operational requirements under field conditions. The state-of-the-art regarding a sensor set-up for the on-line monitoring and secondly, a miniaturised sensor for in-line monitoring are summarised. Furthermore, alternative detection methods and a novel multi-sensor system for the characterisation of aseptic sterilisation processes are described. KW - Calorimetric gas sensor KW - Hydrogen peroxide KW - Multi-sensor system Y1 - 2014 SN - 978-3-642-54518-4 (Print) ; 978-3-642-54519-1 (Online) U6 - http://dx.doi.org/10.1007/5346_2013_51 SP - 279 EP - 309 PB - Springer CY - Heidelberg ER - TY - CHAP A1 - Knott, Thomas C. A1 - Sofronia, Raluca E. A1 - Gerressen, Marcus A1 - Law, Yuen A1 - Davidescu, Arjana A1 - Savii, George G. A1 - Gatzweiler, Karl-Heinz A1 - Staat, Manfred A1 - Kuhlen, Torsten W. T1 - Preliminary bone sawing model for a virtual reality-based training simulator of bilateral sagittal split osteotomy T2 - Biomedical simulation : 6th International Symposium, ISBMS 2014, Strasbourg, France, October 16-17, 2014 : proceedings (Lecture notes in computer science : vol. 8789) N2 - Successful bone sawing requires a high level of skill and experience, which could be gained by the use of Virtual Reality-based simulators. A key aspect of these medical simulators is realistic force feedback. The aim of this paper is to model the bone sawing process in order to develop a valid training simulator for the bilateral sagittal split osteotomy, the most often applied corrective surgery in case of a malposition of the mandible. Bone samples from a human cadaveric mandible were tested using a designed experimental system. Image processing and statistical analysis were used for the selection of four models for the bone sawing process. The results revealed a polynomial dependency between the material removal rate and the applied force. Differences between the three segments of the osteotomy line and between the cortical and cancellous bone were highlighted. KW - Bone sawing KW - virtual reality KW - training simulator Y1 - 2014 SN - 978-3-319-12057-7 (Online) SN - 978-3-319-12056-0 (Print) U6 - http://dx.doi.org/10.1007/978-3-319-12057-7_1 SP - 1 EP - 10 PB - Springer CY - Cham ER - TY - CHAP A1 - Frotscher, Ralf A1 - Goßmann, Matthias A1 - Raatschen, Hans-Jürgen A1 - Temiz Artmann, Aysegül A1 - Staat, Manfred T1 - Simulation of cardiac cell-seeded membranes using the edge-based smoothed FEM T2 - Shell and membrane theories in mechanics and biology. (Advanced structured materials ; 45) N2 - We present an electromechanically coupled Finite Element model for cardiac tissue. It bases on the mechanical model for cardiac tissue of Hunter et al. that we couple to the McAllister-Noble-Tsien electrophysiological model of purkinje fibre cells. The corresponding system of ordinary differential equations is implemented on the level of the constitutive equations in a geometrically and physically nonlinear version of the so-called edge-based smoothed FEM for plates. Mechanical material parameters are determined from our own pressure-deflection experimental setup. The main purpose of the model is to further examine the experimental results not only on mechanical but also on electrophysiological level down to ion channel gates. Moreover, we present first drug treatment simulations and validate the model with respect to the experiments. Y1 - 2015 SN - 978-3-319-02534-6 ; 978-3-319-02535-3 SP - 187 EP - 212 PB - Springer CY - Heidelberg ER - TY - JOUR A1 - Fonti, Patrick A1 - Eilmann, Britta A1 - García-González, Ignacio A1 - von Arx, Georg T1 - Expeditious building of ring-porous earlywood vessel chronologies without loosing signal information JF - Trees : structure and function Y1 - 2009 U6 - http://dx.doi.org/10.1007/s00468-008-0310-z SN - 0931-1890 (Print) SN - 1432-2285 (Online) VL - 23 IS - 3 SP - 665 EP - 671 PB - Springer CY - Berlin ER - TY - CHAP A1 - Alhwarin, Faraj A1 - Ferrein, Alexander A1 - Scholl, Ingrid T1 - IR stereo kinect: improving depth images by combining structured light with IR stereo T2 - PRICAI 2014: Trends in artificial intelligence : 13th Pacific Rim International Conference on Artificial Intelligence : Gold Coast, QLD, Australia, December 1-5, 2014 : proceedings. (Lecture notes in computer science ; vol. 8862) N2 - RGB-D sensors such as the Microsoft Kinect or the Asus Xtion are inexpensive 3D sensors. A depth image is computed by calculating the distortion of a known infrared light (IR) pattern which is projected into the scene. While these sensors are great devices they have some limitations. The distance they can measure is limited and they suffer from reflection problems on transparent, shiny, or very matte and absorbing objects. If more than one RGB-D camera is used the IR patterns interfere with each other. This results in a massive loss of depth information. In this paper, we present a simple and powerful method to overcome these problems. We propose a stereo RGB-D camera system which uses the pros of RGB-D cameras and combine them with the pros of stereo camera systems. The idea is to utilize the IR images of each two sensors as a stereo pair to generate a depth map. The IR patterns emitted by IR projectors are exploited here to enhance the dense stereo matching even if the observed objects or surfaces are texture-less or transparent. The resulting disparity map is then fused with the depth map offered by the RGB-D sensor to fill the regions and the holes that appear because of interference, or due to transparent or reflective objects. Our results show that the density of depth information is increased especially for transparent, shiny or matte objects. Y1 - 2014 SN - 978-3-319-13559-5 (Print) ; 978-3-319-13560-1 (E-Book) U6 - http://dx.doi.org/10.1007/978-3-319-13560-1_33 SP - 409 EP - 421 PB - Springer CY - München ER - TY - CHAP A1 - Tran, Thanh Ngoc A1 - Staat, Manfred T1 - Uncertainty multimode failure and shakedown analysis of shells T2 - Direct methods for limit and shakedown analysis of structures / eds. Paolo Fuschi ... N2 - This paper presents a numerical procedure for reliability analysis of thin plates and shells with respect to plastic collapse or to inadaptation. The procedure involves a deterministic shakedown analysis for each probabilistic iteration, which is based on the upper bound approach and the use of the exact Ilyushin yield surface. Probabilistic shakedown analysis deals with uncertainties originated from the loads, material strength and thickness of the shell. Based on a direct definition of the limit state function, the calculation of the failure probability may be efficiently solved by using the First and Second Order Reliability Methods (FORM and SORM). The problem of reliability of structural systems (series systems) is handled by the application of a special technique which permits to find all the design points corresponding to all the failure modes. Studies show, in this case, that it improves considerably the FORM and SORM results. KW - Limit analysis KW - Shakedown analysis KW - Reliability analysis KW - Multimode failure KW - Non-linear optimization Y1 - 2015 SN - 978-3-319-12927-3 (print) ; 978-3-319-12928-0 (online) U6 - http://dx.doi.org/10.1007/978-3-319-12928-0_14 SP - 279 EP - 298 PB - Springer CY - Cham ER - TY - CHAP A1 - Wollert, Jörg T1 - Bussysteme T2 - Handbuch der Mess- und Automatisierungstechnik in der Produktion / Hans-Jürgen Gevatter ... (Hrsg.). - 2. Aufl. Y1 - 2006 SN - 3-540-21207-8 ; 978-3-540-21207-2 SP - 475 EP - 653 PB - Springer CY - Berlin [u.a.] ER - TY - JOUR A1 - Hafner, David A1 - Demetz, Oliver A1 - Weickert, Joachim A1 - Reißel, Martin T1 - Mathematical Foundations and Generalisations of the Census Transform for Robust Optic Flow Computation JF - Journal of Mathematical Imaging and Vision Y1 - 2014 U6 - http://dx.doi.org/10.1007/s10851-014-0529-9 SN - 1573-7683 (Online) N1 - Springer Online First (ohne Seitenang. und Heftzuteilung) PB - Springer CY - New York ER - TY - CHAP A1 - Pietsch, Wolfram A1 - Siedentopf, Jukka A1 - Teubner, Alexander ED - Gaul, Wolfgang ED - Bachem, Achim ED - Habenicht, Walter ED - Runge, Walter ED - Stahl, Wolfgang W. T1 - Vergleich konnektionistischer Modelle und konventioneller Optimierungsverfahren am Beispiel der Maschinenbelegungsplanung T2 - Operations Research Proceedings 1991 / Papers of the 20th Annual Meeting = Vorträge der 20. Jahrestagung N2 - Für die Erstellung von Maschinenbelegungsplanen wurden im Operations Research aufwendige Optimierungsverfahren konzipiert und entsprechende Programme entwickelt. Maschinenbelegungsprobleme sind klassische Vertreter der Klasse der np-vollständigen Probleme, also sichere Kandidaten für kombinatorische Explosion der Lösungsalternativen. Deshalb ist der Einsatz konventioneller Planungssysteme wegen der hohen Rechneranforderungen der gängigen Verfahren an die Hardware oft nicht praktikabel. Y1 - 1992 SN - 978-3-642-46773-8 (Online) SN - 978-3-540-55410-3 (Print) U6 - http://dx.doi.org/https://doi.org/10.1007/978-3-642-46773-8_58 N1 - Part of the book series: Operations Research Proceedings (ORP, volume 1991) SP - 223 PB - Springer CY - Berlin ; Heidelberg ER - TY - JOUR A1 - Borchert, Jörg A1 - Hasenbeck, Marc A1 - Jungbluth, Christian A1 - Schemm, Ralf T1 - Bewertung und Steuerung von Gasspeichern bzw. Gasspeicherscheiben JF - Zeitschrift für Energiewirtschaft N2 - In diesem Artikel werden zunächst einleitend der Gasmarkt Deutschland und der sich daraus ergebende Speicherbedarf skizziert. Folgend wird auf verschiedene Speichernutzen aus betriebswirtschaftlicher Perspektive eingegangen und die in diesem Artikel vorgestellten Bewertungsverfahren einleitend beschrieben. In diesem Artikel werden stochastische Optimierungsmethoden aufgegriffen, die sowohl eine Bewertung der Speicher gegenüber einem Spotpreis, als auch gegenüber einer gesamten Forwardcurve ermöglichen. Hierzu werden zunächst Modelle zur Beschreibung der Marktpreise vorgestellt und anhand empirischer Daten kalibriert. Dann wird eine beispielhafte Speicherscheibe zunächst auf Basis der LeastSquareMonteCarloTechnik gegenüber dem stochastischen mehrfaktoriellen Spotpreismodell bewertet. Hieran schließt sich die Vorstellung der Bewertung sowie des Hedgings gegenüber der Forwardcurve an. Abschließend erfolgt eine vergleichende Gegenüberstellung beider Verfahren. Y1 - 2009 U6 - http://dx.doi.org/10.1007/s12398-009-0033-x SN - 1866-2765 VL - 33 IS - 4 SP - 279 EP - 293 PB - Springer CY - Berlin ER -