TY - CHAP A1 - Ludowicy, Jonas A1 - Rings, René A1 - Finger, Felix A1 - Braun, Carsten T1 - Sizing Studies of Light Aircraft with Parallel Hybrid Propulsion Systems T2 - Deutscher Luft- und Raumfahrtkongress 2018 Y1 - 2018 U6 - http://dx.doi.org/10.25967/480227 ER - TY - CHAP A1 - Ludowicy, Jonas A1 - Rings, René A1 - Finger, Felix A1 - Braun, Carsten A1 - Bil, Cees T1 - Impact of Propulsion Technology Levels on the Sizing and Energy Consumption for Serial HybridElectric General Aviation Aircraft T2 - Asia Pacific International Symposium on Aerospace Technology. APISAT 2019 Y1 - 2019 ER - TY - CHAP A1 - Mathiak, Gerhard A1 - Plescher, Engelbert A1 - Willnecker, Rainer T1 - Parabolic flight experiments about vibrational effects on diffusion experiments T2 - 54th International Astronautical Congress of the International Astronautical Federation (IAF) : Bremen, 29 Sept. 2003 through 3 Oct. 2003 ; vol. 1 Y1 - 2003 SP - 4389 EP - 4396 ER - TY - CHAP A1 - Mertens, Josef T1 - Laminar leading edges: manufacturing, contamination, and operational aspects - results from the German RaWid programme N2 - RaWid was the German national technology programme on transonic aerodynamics and supporting technologies, lasting from 1995 to 1998. One of the main topics was laminar wing development. Besides aerodynamic design work, many operational aspects were investigated. A manufacturing concept was developed to be applied to operational laminar wings and empennages. It was built in a large scale manufacturing demonstrator with the aerodynamic shape of a 1,5 m section of the A320 fin nose. Tolerances in shape and roughness fulfilled all requirements. The construction can easily be adapted to varying stiffness and strength requirements. Weight and manufacturing costs are comparable to common nose designs. The mock-up to be designed in ALTTA is based on this manufacturing principle. Another critical point is contamination of suction surfaces. Several tests were performed to investigate perforated titanium suction surfaces at realistic operational conditions: - a one year flight test with a suction plate in the stagnation area of the Airbus "Beluga" - a one year test of several suction plates in a ground test near the airport - a one year test of a working suction ground test installation at all weather conditions. No critical results were found. There is no long term suction degradation visible. Icing conditions and ground de-icing fluids used on airports did not pose severe problems. Some problems detected require only respection of weak design constraints. KW - Laminare Strömung KW - Ansaugsystem KW - Profilumströmung KW - Laminarprofil KW - RaWid KW - hybrid laminar flow KW - suction systems KW - suction structure KW - contamination KW - operational aspects Y1 - 2000 ER - TY - CHAP A1 - Mertens, Josef T1 - Next steps envisaged to improve wing performance of commercial aircraft T2 - Aerodynamic drag reduction technologies : proceedings of the CEAS/DragNet European Drag Reduction Conference, 19–21 June 2000, Potsdam, Germany. - (Notes on numerical fluid mechanics ; 76) Y1 - 2001 SN - 3-540-41911-X (Print) SN - 978-3-540-45359-8 (Elektronisch) U6 - http://dx.doi.org/10.1007/978-3-540-45359-8_26 SP - 246 EP - 255 PB - Springer CY - Berlin [u.a.] ER - TY - CHAP A1 - Mertens, Josef ED - Nitsche, Wolfgang T1 - Some important results of the technology programme RaWid T2 - New Results in Numerical and Experimental Fluid Mechanics : Contributions to the 11th AG STAB/DGLR Symposium Berlin, Germany 1998. - Vol. 2. - (Notes on Numerical Fluid Mechanics ; 72) Y1 - 1999 SN - 978-3-663-10903-7 (Print) SN - 978-3-663-10901-3 (Elektronisch) U6 - http://dx.doi.org/10.1007/978-3-663-10901-3_41 SP - 315 EP - 322 PB - Springer Fachmedien CY - Wiesbaden ER - TY - CHAP A1 - Möhren, Felix A1 - Bergmann, Ole A1 - Janser, Frank A1 - Braun, Carsten T1 - On the determination of harmonic propeller loads T2 - AIAA SCITECH 2023 Forum N2 - Dynamic loads significantly impact the structural design of propeller blades due to fatigue and static strength. Since propellers are elastic structures, deformations and aerodynamic loads are coupled. In the past, propeller manufacturers established procedures to determine unsteady aerodynamic loads and the structural response with analytical steady-state calculations. According to the approach, aeroelastic coupling primarily consists of torsional deformations. They neglect bending deformations, deformation velocities, and inertia terms. This paper validates the assumptions above for a General Aviation propeller and a lift propeller for urban air mobility or large cargo drones. Fully coupled reduced-order simulations determine the dynamic loads in the time domain. A quasi-steady blade element momentum approach transfers loads to one-dimensional finite beam elements. The simulation results are in relatively good agreement with the analytical method for the General Aviation propeller but show increasing errors for the slender lift propeller. The analytical approach is modified to consider the induced velocities. Still, inertia and velocity proportional terms play a significant role for the lift propeller due to increased elasticity. The assumption that only torsional deformations significantly impact the dynamic loads of propellers is not valid. Adequate determination of dynamic loads of such designs requires coupled aeroelastic simulations or advanced analytical procedures. Y1 - 2023 U6 - http://dx.doi.org/10.2514/6.2023-2404 N1 - AIAA SCITECH 2023 Forum, 23-27 January 2023, National Harbor, MD & Online PB - AIAA ER - TY - CHAP A1 - Neu, Eugen A1 - Janser, Frank A1 - Khatibi, Akbar A. A1 - Orifici, Adrian C. T1 - Operational modal analysis of a cantilever in a wind tunnel using optical fiber bragg grating sensors T2 - 6th International Operational Modal Analysis Conference. IOMAC´15. 2015 May 12-14 Gijon - Spain Y1 - 2015 U6 - http://dx.doi.org/10.13140/RG.2.1.3753.0324 ER - TY - CHAP A1 - Neu, Eugen A1 - Janser, Frank A1 - Khatibi, Akbar A. A1 - Orifici, Adrian C. T1 - In-flight vibration-based structural health monitoring of aircraft wings T2 - 30th Congress of the internatonal council of the aeronautical sciences : 25.-30. September 2016, Daejeon, Korea N2 - This work presents a methodology for automated damage-sensitive feature extraction and anomaly detection under multivariate operational variability for in-flight assessment of wings. The method uses a passive excitation approach, i. e. without the need for artificial actuation. The modal system properties (natural frequencies and damping ratios) are used as damage-sensitive features. Special emphasis is placed on the use of Fiber Bragg Grating (FBG) sensing technology and the consideration of Operational and Environmental Variability (OEV). Measurements from a wind tunnel investigation with a composite cantilever equipped with FBG and piezoelectric sensors are used to successfully detect an impact damage. In addition, the feasibility of damage localisation and severity estimation is evaluated based on the coupling found between damageand OEV-induced feature changes. Y1 - 2016 ER - TY - CHAP A1 - Niedermeier, H. A1 - Clemens, J. A1 - Kowalski, Julia A1 - Macht, S. A1 - Heinen, D. A1 - Hoffmann, R. A1 - Linder, Peter T1 - Navigation system for a research ice probe for antarctic glaciers T2 - IEEE/ION Position, Location and Navigation Symposium (PLANS) ; 5-8 May 2014, Monterey, Calif. Y1 - 2014 SN - 978-1-4799-3319-8 SP - 959 EP - 975 PB - IEEE CY - Piscataway, NJ ER -